amr(4): Sync with FreeBSD.
[dragonfly.git] / sys / config / LINT
CommitLineData
984263bc
MD
1#
2# LINT -- config file for checking all the sources, tries to pull in
3# as much of the source tree as it can.
4#
5# $FreeBSD: src/sys/i386/conf/LINT,v 1.749.2.144 2003/06/04 17:56:59 sam Exp $
84bc65d9
TN
6#
7# See the kernconf(5) manual page for more information on the format of
8# this file.
984263bc
MD
9#
10# NB: You probably don't want to try running a kernel built from this
11# file. Instead, you should start from GENERIC, and add options from
12# this file as required.
13#
14
a9295349
MD
15# These directives are mandatory. The machine directive specifies the
16# platform and the machine_arch directive specifies the cpu architecture.
984263bc 17#
0955fd91
MD
18platform pc32
19machine i386
a9295349 20machine_arch i386
984263bc
MD
21
22#
23# This is the ``identification'' of the kernel. Usually this should
24# be the same as the name of your kernel.
25#
26ident LINT
27
28#
29# The `maxusers' parameter controls the static sizing of a number of
30# internal system tables by a formula defined in subr_param.c. Setting
31# maxusers to 0 will cause the system to auto-size based on physical
32# memory.
33#
34maxusers 10
35
36#
37# The `makeoptions' parameter allows variables to be passed to the
38# generated Makefile in the build area.
39#
40# CONF_CFLAGS gives some extra compiler flags that are added to ${CFLAGS}
41# after most other flags. Here we use it to inhibit use of non-optimal
42# gcc builtin functions (e.g., memcmp).
43#
44# DEBUG happens to be magic.
45# The following is equivalent to 'config -g KERNELNAME' and creates
46# 'kernel.debug' compiled with -g debugging as well as a normal
47# 'kernel'. Use 'make install.debug' to install the debug kernel
48# but that isn't normally necessary as the debug symbols are not loaded
49# by the kernel and are not useful there anyway.
50#
51# KERNEL can be overridden so that you can change the default name of your
52# kernel.
53#
54# MODULES_OVERRIDE can be used to limit modules built to a specific list.
55#
c2c83759
MD
56# INSTALLSTRIPPED can be set to cause installkernel to install stripped
57# kernels and modules rather than a kernel and modules with debug symbols.
58#
59# INSTALLSTRIPPEDMODULES can be set to allow a full debug kernel to be
60# installed, but to strip the installed modules.
61#
984263bc
MD
62makeoptions CONF_CFLAGS=-fno-builtin #Don't allow use of memcmp, etc.
63#makeoptions DEBUG=-g #Build kernel with gdb(1) debug symbols
64#makeoptions KERNEL=foo #Build kernel "foo" and install "/foo"
65# Only build Linux API modules and plus those parts of the sound system I need.
66#makeoptions MODULES_OVERRIDE="linux sound/snd sound/pcm sound/driver/maestro3"
c2c83759
MD
67#makeoptions INSTALLSTRIPPED=1
68#makeoptions INSTALLSTRIPPEDMODULES=1
984263bc
MD
69
70#
71# Certain applications can grow to be larger than the 128M limit
fc29bf55 72# that DragonFly initially imposes. Below are some options to
984263bc
MD
73# allow that limit to grow to 256MB, and can be increased further
74# with changing the parameters. MAXDSIZ is the maximum that the
75# limit can be set to, and the DFLDSIZ is the default value for
76# the limit. MAXSSIZ is the maximum that the stack limit can be
d856dabc 77# set to. You might want to set the default lower than the max,
984263bc
MD
78# and explicitly set the maximum with a shell command for processes
79# that regularly exceed the limit like INND.
80#
81options MAXDSIZ="(256*1024*1024)"
82options MAXSSIZ="(256*1024*1024)"
83options DFLDSIZ="(256*1024*1024)"
84
85#
86# BLKDEV_IOSIZE sets the default block size used in user block
56be8454 87# device I/O. Note that this value will be overridden by the label
984263bc
MD
88# when specifying a block device from a label with a non-0
89# partition blocksize. The default is PAGE_SIZE.
90#
91options BLKDEV_IOSIZE=8192
92
93# Options for the VM subsystem.
94options PQ_CACHESIZE=512 # color for 512k/16k cache
984263bc
MD
95
96# This allows you to actually store this configuration file into
97# the kernel binary itself, where it may be later read by saying:
98# strings -n 3 /kernel | sed -n 's/^___//p' > MYKERNEL
99#
100options INCLUDE_CONFIG_FILE # Include this file in kernel
101
102#
103# The root device and filesystem type can be compiled in;
104# this provides a fallback option if the root device cannot
105# be correctly guessed by the bootstrap code, or an override if
106# the RB_DFLTROOT flag (-r) is specified when booting the kernel.
107#
108options ROOTDEVNAME=\"ufs:da0s2e\"
109
110\f
111#####################################################################
112# SMP OPTIONS:
113#
114# SMP enables building of a Symmetric MultiProcessor Kernel.
984263bc
MD
115#
116# Notes:
117#
118# An SMP kernel will ONLY run on an Intel MP spec. qualified motherboard.
119#
4db955e1 120# Be sure to disable 'cpu I486_CPU' for SMP kernels.
984263bc
MD
121#
122# Check the 'Rogue SMP hardware' section to see if additional options
123# are required by your hardware.
124#
125
3b0db00f 126# SMP boxes with severely broken BIOSes which
84bc65d9 127# boot fine for non-SMP builds *might* work in SMP mode
3b0db00f 128# if you disable APIC_IO by setting the loader tunable
1f15ba20 129# hw.apic_io_enable to 0.
84bc65d9 130#
984263bc 131options SMP # Symmetric MultiProcessor Kernel
984263bc
MD
132
133#
134# Rogue SMP hardware:
135#
136
137# Bridged PCI cards:
138#
139# The MP tables of most of the current generation MP motherboards
140# do NOT properly support bridged PCI cards. To use one of these
141# cards you should refer to ???
142
143\f
144#####################################################################
145# CPU OPTIONS
146
147#
148# You must specify at least one CPU (the one you intend to run on);
149# deleting the specification for CPUs you don't need to use may make
4db955e1 150# parts of the system run faster.
984263bc 151#
984263bc
MD
152cpu I486_CPU
153cpu I586_CPU # aka Pentium(tm)
154cpu I686_CPU # aka Pentium Pro(tm)
155
156#
157# Options for CPU features.
158#
53c1a7a7
MD
159# CPU_AMD64X2_INTR_SPAM tries to route HyperTransport EXTINT and NMI
160# messages to LINT0 on the local APIC when the BIOS has forgotten to
161# do that. If this is not done on a multi-core cpu, EXTINT and NMI
3f5e28f4 162# get routed to the INTR/NMI pins on *BOTH* cores simultaneously, causing
53c1a7a7 163# two INTA ack cycles one of which will almost certainly result in a
d856dabc 164# spurious interrupt vector being presented. This is often visible as
53c1a7a7
MD
165# an unmaskable IRQ 7 which occurs for every normal interrupt that occurs
166# on a system.
167#
984263bc
MD
168# CPU_ATHLON_SSE_HACK tries to enable SSE instructions when the BIOS has
169# forgotten to enable them.
170#
171# CPU_BLUELIGHTNING_FPU_OP_CACHE enables FPU operand cache on IBM
172# BlueLightning CPU. It works only with Cyrix FPU, and this option
173# should not be used with Intel FPU.
174#
175# CPU_BLUELIGHTNING_3X enables triple-clock mode on IBM Blue Lightning
176# CPU if CPU supports it. The default is double-clock mode on
177# BlueLightning CPU box.
178#
179# CPU_BTB_EN enables branch target buffer on Cyrix 5x86 (NOTE 1).
180#
181# CPU_DIRECT_MAPPED_CACHE sets L1 cache of Cyrix 486DLC CPU in direct
182# mapped mode. Default is 2-way set associative mode.
183#
184# CPU_CYRIX_NO_LOCK enables weak locking for the entire address space
185# of Cyrix 6x86 and 6x86MX CPUs by setting the NO_LOCK bit of CCR1.
186# Otherwise, the NO_LOCK bit of CCR1 is cleared. (NOTE 3)
187#
188# CPU_DISABLE_5X86_LSSER disables load store serialize (i.e. enables
189# reorder). This option should not be used if you use memory mapped
190# I/O device(s).
191#
642a6e88 192# CPU_DISABLE_SSE disables SSE/MMX2 instructions support.
984263bc 193#
18a582c9
JR
194# CPU_ENABLE_TCC enables Thermal Control Circuitry (TCC) found in some
195# Pentium(tm) 4 and (possibly) later CPUs. When enabled and detected,
196# TCC supports restricting power consumption using the hw.p4tcc.*
197# sysctls. This operates independently of SpeedStep and is useful on
198# systems where other mechanisms such as apm(4) or acpi(4) don't work.
199#
5d327b77
YT
200# CPU_ENABLE_EST enables support for Enhanced SpeedStep technology
201# found in Pentium(tm) M processors.
202#
984263bc
MD
203# CPU_FASTER_5X86_FPU enables faster FPU exception handler.
204#
205# CPU_I486_ON_386 enables CPU cache on i486 based CPU upgrade products
206# for i386 machines.
207#
208# CPU_IORT defines I/O clock delay time (NOTE 1). Default values of
209# I/O clock delay time on Cyrix 5x86 and 6x86 are 0 and 7,respectively
210# (no clock delay).
211#
3f5e28f4 212# CPU_L2_LATENCY specified the L2 cache latency value. This option is used
984263bc
MD
213# only when CPU_PPRO2CELERON is defined and Mendocino Celeron is detected.
214# The default value is 5.
215#
216# CPU_ELAN enables support for AMDs ElanSC520 CPU.
217#
80c3f755
AH
218# CPU_GEODE enables support for AMD Geode LX, Geode SC1100 and AMD CS5536
219#
984263bc
MD
220# CPU_LOOP_EN prevents flushing the prefetch buffer if the destination
221# of a jump is already present in the prefetch buffer on Cyrix 5x86(NOTE
222# 1).
223#
224# CPU_PPRO2CELERON enables L2 cache of Mendocino Celeron CPUs. This option
225# is useful when you use Socket 8 to Socket 370 converter, because most Pentium
226# Pro BIOSs do not enable L2 cache of Mendocino Celeron CPUs.
227#
228# CPU_RSTK_EN enables return stack on Cyrix 5x86 (NOTE 1).
229#
230# CPU_SUSP_HLT enables suspend on HALT. If this option is set, CPU
231# enters suspend mode following execution of HALT instruction.
232#
233# CPU_WT_ALLOC enables write allocation on Cyrix 6x86/6x86MX and AMD
234# K5/K6/K6-2 cpus.
235#
236# CYRIX_CACHE_WORKS enables CPU cache on Cyrix 486 CPUs with cache
237# flush at hold state.
238#
239# CYRIX_CACHE_REALLY_WORKS enables (1) CPU cache on Cyrix 486 CPUs
240# without cache flush at hold state, and (2) write-back CPU cache on
241# Cyrix 6x86 whose revision < 2.7 (NOTE 2).
242#
243# NO_F00F_HACK disables the hack that prevents Pentiums (and ONLY
244# Pentiums) from locking up when a LOCK CMPXCHG8B instruction is
245# executed. This option is only needed if I586_CPU is also defined,
246# and should be included for any non-Pentium CPU that defines it.
247#
248# NO_MEMORY_HOLE is an optimisation for systems with AMD K6 processors
249# which indicates that the 15-16MB range is *definitely* not being
250# occupied by an ISA memory hole.
251#
252# NOTE 1: The options, CPU_BTB_EN, CPU_LOOP_EN, CPU_IORT,
253# CPU_LOOP_EN and CPU_RSTK_EN should not be used because of CPU bugs.
254# These options may crash your system.
255#
256# NOTE 2: If CYRIX_CACHE_REALLY_WORKS is not set, CPU cache is enabled
257# in write-through mode when revision < 2.7. If revision of Cyrix
258# 6x86 >= 2.7, CPU cache is always enabled in write-back mode.
259#
260# NOTE 3: This option may cause failures for software that requires
261# locked cycles in order to operate correctly.
262#
e71347e9 263options CPU_AMD64X2_INTR_SPAM
984263bc
MD
264options CPU_ATHLON_SSE_HACK
265options CPU_BLUELIGHTNING_FPU_OP_CACHE
266options CPU_BLUELIGHTNING_3X
267options CPU_BTB_EN
e71347e9 268options CPU_CYRIX_NO_LOCK
984263bc
MD
269options CPU_DIRECT_MAPPED_CACHE
270options CPU_DISABLE_5X86_LSSER
e71347e9 271options CPU_DISABLE_SSE
984263bc 272options CPU_ELAN
5d327b77 273options CPU_ENABLE_EST
18a582c9 274options CPU_ENABLE_TCC
984263bc 275options CPU_FASTER_5X86_FPU
80c3f755 276options CPU_GEODE
984263bc
MD
277options CPU_I486_ON_386
278options CPU_IORT
279options CPU_L2_LATENCY=5
280options CPU_LOOP_EN
281options CPU_PPRO2CELERON
282options CPU_RSTK_EN
283options CPU_SUSP_HLT
284options CPU_WT_ALLOC
285options CYRIX_CACHE_WORKS
286options CYRIX_CACHE_REALLY_WORKS
287#options NO_F00F_HACK
e71347e9 288options NO_MEMORY_HOLE
984263bc
MD
289
290#
291# A math emulator is mandatory if you wish to run on hardware which
6f535fd5 292# does not have a floating-point processor.
984263bc 293options MATH_EMULATE #Support for x87 emulation
984263bc
MD
294\f
295#####################################################################
d856dabc 296# COMPATIBILITY OPTIONS
984263bc
MD
297
298#
299# Implement system calls compatible with 4.3BSD and older versions of
300# FreeBSD. You probably do NOT want to remove this as much current code
301# still relies on the 4.3 emulation.
302#
303options COMPAT_43
304
305#
db37e804
JS
306# Implement system calls compatible with DragonFly 1.2 and older.
307#
308options COMPAT_DF12 #Compatible with DragonFly 1.2 and earlier
309
310#
984263bc
MD
311# These three options provide support for System V Interface
312# Definition-style interprocess communication, in the form of shared
313# memory, semaphores, and message queues, respectively.
314#
315# System V shared memory and tunable parameters
316options SYSVSHM # include support for shared memory
317options SHMMAXPGS=1025 # max amount of shared memory pages (4k on i386)
318options SHMALL=1025 # max amount of shared memory (bytes)
319options SHMMAX="(SHMMAXPGS*PAGE_SIZE+1)"
320 # max shared memory segment size (bytes)
321options SHMMIN=2 # min shared memory segment size (bytes)
322options SHMMNI=33 # max number of shared memory identifiers
323options SHMSEG=9 # max shared memory segments per process
324
325# System V semaphores and tunable parameters
326options SYSVSEM # include support for semaphores
327options SEMMAP=31 # amount of entries in semaphore map
328options SEMMNI=11 # number of semaphore identifiers in the system
329options SEMMNS=61 # number of semaphores in the system
330options SEMMNU=31 # number of undo structures in the system
331options SEMMSL=61 # max number of semaphores per id
332options SEMOPM=101 # max number of operations per semop call
333options SEMUME=11 # max number of undo entries per process
334
335# System V message queues and tunable parameters
336options SYSVMSG # include support for message queues
337options MSGMNB=2049 # max characters per message queue
338options MSGMNI=41 # max number of message queue identifiers
339options MSGSEG=2049 # max number of message segments in the system
340options MSGSSZ=16 # size of a message segment MUST be power of 2
341options MSGTQL=41 # max amount of messages in the system
342
343\f
344#####################################################################
345# DEBUGGING OPTIONS
346
347#
348# Enable the kernel debugger.
349#
350options DDB
351
352#
4ad6607f
SW
353# Print a stack trace on kernel panic.
354#
355options DDB_TRACE
356
357#
984263bc
MD
358# Don't drop into DDB for a panic. Intended for unattended operation
359# where you may want to drop to DDB from the console, but still want
360# the machine to recover from a panic
361#
362options DDB_UNATTENDED
363
364#
365# If using GDB remote mode to debug the kernel, there's a non-standard
366# extension to the remote protocol that can be used to use the serial
367# port as both the debugging port and the system console. It's non-
368# standard and you're on your own if you enable it. See also the
fc29bf55 369# "remotechat" variables in the DragonFly specific version of gdb.
984263bc
MD
370#
371options GDB_REMOTE_CHAT
372
373#
374# KTRACE enables the system-call tracing facility ktrace(2).
375#
376options KTRACE #kernel tracing
377
378#
379# The INVARIANTS option is used in a number of source files to enable
380# extra sanity checking of internal structures. This support is not
381# enabled by default because of the extra time it would take to check
382# for these conditions, which can only occur as a result of
383# programming errors.
384#
385options INVARIANTS
386
387#
984263bc
MD
388# The DIAGNOSTIC option is used to enable extra debugging information
389# from some parts of the kernel. As this makes everything more noisy,
390# it is disabled by default.
391#
392options DIAGNOSTIC
393
394#
395# PERFMON causes the driver for Pentium/Pentium Pro performance counters
396# to be compiled. See perfmon(4) for more information.
397#
398options PERFMON
399
400
401#
402# This option let some drivers co-exist that can't co-exist in a running
403# system. This is used to be able to compile all kernel code in one go for
404# quality assurance purposes (like this file, which the option takes it name
405# from.)
406#
407options COMPILING_LINT
408
409
410# XXX - this doesn't belong here.
411# Allow ordinary users to take the console - this is useful for X.
412options UCONSOLE
413
414# XXX - this doesn't belong here either
415options USERCONFIG #boot -c editor
416options INTRO_USERCONFIG #imply -c and show intro screen
417options VISUAL_USERCONFIG #visual boot -c editor
418
419\f
420#####################################################################
421# NETWORKING OPTIONS
422
423#
424# Protocol families:
fc29bf55 425# Only the INET (Internet) family is officially supported in DragonFly.
984263bc
MD
426# Source code for the NS (Xerox Network Service) is provided for amusement
427# value.
428#
429options INET #Internet communications protocols
430options INET6 #IPv6 communications protocols
431options IPSEC #IP security
432options IPSEC_ESP #IP security (crypto; define w/ IPSEC)
433options IPSEC_DEBUG #debug for IP security
434#
435# Set IPSEC_FILTERGIF to force packets coming through a gif tunnel
436# to be processed by any configured packet filtering (ipfw, ipf).
437# The default is that packets coming from a tunnel are _not_ processed;
438# they are assumed trusted.
439#
440# Note that enabling this can be problematic as there are no mechanisms
441# in place for distinguishing packets coming out of a tunnel (e.g. no
442# encX devices as found on openbsd).
443#
444#options IPSEC_FILTERGIF #filter ipsec packets from a tunnel
445
446#
447# Experimental IPsec implementation that uses the kernel crypto
448# framework. This cannot be configured together with IPSEC and
449# (currently) supports only IPv4. To use this you must also
450# configure the crypto device (see below). Note that with this
451# you get all the IPsec protocols (e.g. there is no FAST_IPSEC_ESP).
452# IPSEC_DEBUG is used, as above, to configure debugging support
453# within the IPsec protocols.
454#
455#options FAST_IPSEC #new IPsec
456
457options IPX #IPX/SPX communications protocols
458options IPXIP #IPX in IP encapsulation (not available)
459options IPTUNNEL #IP in IPX encapsulation (not available)
460
461options NCP #NetWare Core protocol
462
b202117f
NA
463options MPLS #Multi-Protocol Label Switching
464
984263bc
MD
465options NETATALK #Appletalk communications protocols
466
467# These are currently broken but are shipped due to interest.
468#options NS #Xerox NS protocols
469#options NSIP #XNS over IP
470
471#
472# SMB/CIFS requester
473# NETSMB enables support for SMB protocol, it requires LIBMCHAIN and LIBICONV
474# options.
475# NETSMBCRYPTO enables support for encrypted passwords.
476options NETSMB #SMB/CIFS requester
477options NETSMBCRYPTO #encrypted password support for SMB
478
479# mchain library. It can be either loaded as KLD or compiled into kernel
480options LIBMCHAIN #mbuf management library
481
482# netgraph(4). Enable the base netgraph code with the NETGRAPH option.
483# Individual node types can be enabled with the corresponding option
484# listed below; however, this is not strictly necessary as netgraph
485# will automatically load the corresponding KLD module if the node type
486# is not already compiled into the kernel. Each type below has a
4ad6607f 487# corresponding man page, e.g., ng_async(4).
984263bc
MD
488options NETGRAPH #netgraph(4) system
489options NETGRAPH_ASYNC
490options NETGRAPH_BPF
4ad6607f 491options NETGRAPH_BRIDGE
984263bc
MD
492options NETGRAPH_CISCO
493options NETGRAPH_ECHO
7dab44e5 494options NETGRAPH_EIFACE
984263bc
MD
495options NETGRAPH_ETHER
496options NETGRAPH_FRAME_RELAY
497options NETGRAPH_HOLE
498options NETGRAPH_IFACE
499options NETGRAPH_KSOCKET
500options NETGRAPH_L2TP
501options NETGRAPH_LMI
502# MPPC compression requires proprietary files (not included)
503#options NETGRAPH_MPPC_COMPRESSION
504options NETGRAPH_MPPC_ENCRYPTION
505options NETGRAPH_ONE2MANY
506options NETGRAPH_PPP
507options NETGRAPH_PPPOE
508options NETGRAPH_PPTPGRE
509options NETGRAPH_RFC1490
510options NETGRAPH_SOCKET
511options NETGRAPH_TEE
512options NETGRAPH_TTY
513options NETGRAPH_UI
514options NETGRAPH_VJC
515
516device mn # Munich32x/Falc54 Nx64kbit/sec cards.
517
518#
519# Network interfaces:
520# The `loop' pseudo-device is MANDATORY when networking is enabled.
521# The `ether' pseudo-device provides generic code to handle
522# Ethernets; it is MANDATORY when a Ethernet device driver is
b15531e9 523# configured.
984263bc 524# The `sppp' pseudo-device serves a similar role for certain types
9e2b517e 525# of synchronous PPP links (like `ar').
984263bc
MD
526# The `sl' pseudo-device implements the Serial Line IP (SLIP) service.
527# The `ppp' pseudo-device implements the Point-to-Point Protocol.
528# The `bpf' pseudo-device enables the Berkeley Packet Filter. Be
529# aware of the legal and administrative consequences of enabling this
530# option. The number of devices determines the maximum number of
531# simultaneous BPF clients programs runnable.
532# The `disc' pseudo-device implements a minimal network interface,
533# which throws away all packets sent and never receives any. It is
534# included for testing purposes. This shows up as the 'ds' interface.
535# The `tun' pseudo-device implements (user-)ppp and nos-tun
536# The `gif' pseudo-device implements IPv6 over IP4 tunneling,
537# IPv4 over IPv6 tunneling, IPv4 over IPv4 tunneling and
538# IPv6 over IPv6 tunneling.
539# The `gre' device implements two types of IP4 over IP4 tunneling:
540# GRE and MOBILE, as specified in the RFC1701 and RFC2004.
541# The `faith' pseudo-device captures packets sent to it and diverts them
542# to the IPv4/IPv6 translation daemon.
543# The `stf' device implements 6to4 encapsulation.
544# The `ef' pseudo-device provides support for multiple ethernet frame types
545# specified via ETHER_* options. See ef(4) for details.
546#
547# The PPP_BSDCOMP option enables support for compress(1) style entire
548# packet compression, the PPP_DEFLATE is for zlib/gzip style compression.
549# PPP_FILTER enables code for filtering the ppp data stream and selecting
550# events for resetting the demand dial activity timer - requires bpf.
551# See pppd(8) for more details.
552#
553pseudo-device ether #Generic Ethernet
554pseudo-device vlan 1 #VLAN support
db37145f 555pseudo-device bridge #Bridging support
984263bc
MD
556pseudo-device sppp #Generic Synchronous PPP
557pseudo-device loop #Network loopback device
558pseudo-device bpf #Berkeley packet filter
559pseudo-device disc #Discard device (ds0, ds1, etc)
560pseudo-device tun #Tunnel driver (ppp(8), nos-tun(8))
561pseudo-device sl 2 #Serial Line IP
562pseudo-device gre #IP over IP tunneling
563pseudo-device ppp 2 #Point-to-point protocol
564options PPP_BSDCOMP #PPP BSD-compress support
565options PPP_DEFLATE #PPP zlib/deflate/gzip support
566options PPP_FILTER #enable bpf filtering (needs bpf)
567
568pseudo-device ef # Multiple ethernet frames support
569options ETHER_II # enable Ethernet_II frame
570options ETHER_8023 # enable Ethernet_802.3 (Novell) frame
571options ETHER_8022 # enable Ethernet_802.2 frame
572options ETHER_SNAP # enable Ethernet_802.2/SNAP frame
573
574# for IPv6
575pseudo-device gif #IPv6 and IPv4 tunneling
576pseudo-device faith 1 #for IPv6 and IPv4 translation
577pseudo-device stf #6to4 IPv6 over IPv4 encapsulation
578
579#
580# Internet family options:
581#
582# MROUTING enables the kernel multicast packet forwarder, which works
583# with mrouted(8).
584#
f1f552f6
JH
585# PIM enables Protocol Independent Multicast in the kernel.
586# Requires MROUTING enabled.
587#
984263bc
MD
588# IPFIREWALL enables support for IP firewall construction, in
589# conjunction with the `ipfw' program. IPFIREWALL_VERBOSE sends
590# logged packets to the system logger. IPFIREWALL_VERBOSE_LIMIT
591# limits the number of times a matching entry can be logged.
592#
593# WARNING: IPFIREWALL defaults to a policy of "deny ip from any to any"
594# and if you do not add other rules during startup to allow access,
595# YOU WILL LOCK YOURSELF OUT. It is suggested that you set firewall_type=open
596# in /etc/rc.conf when first enabling this feature, then refining the
597# firewall rules in /etc/rc.firewall after you've tested that the new kernel
598# feature works properly.
599#
600# IPFIREWALL_DEFAULT_TO_ACCEPT causes the default rule (at boot) to
601# allow everything. Use with care, if a cracker can crash your
602# firewall machine, they can get to your protected machines. However,
603# if you are using it as an as-needed filter for specific problems as
604# they arise, then this may be for you. Changing the default to 'allow'
605# means that you won't get stuck if the kernel and /sbin/ipfw binary get
606# out of sync.
607#
608# IPDIVERT enables the divert IP sockets, used by ``ipfw divert''
609#
610# IPSTEALTH enables code to support stealth forwarding (i.e., forwarding
611# packets without touching the ttl). This can be useful to hide firewalls
612# from traceroute and similar tools.
613#
614# TCPDEBUG is undocumented.
615#
616options MROUTING # Multicast routing
f1f552f6 617options PIM # Protocol Independent Multicast
984263bc 618options IPFIREWALL #firewall
8d0865c8 619options IPFIREWALL_DEBUG #debug prints
984263bc
MD
620options IPFIREWALL_VERBOSE #enable logging to syslogd(8)
621options IPFIREWALL_FORWARD #enable transparent proxy support
622options IPFIREWALL_VERBOSE_LIMIT=100 #limit verbosity
623options IPFIREWALL_DEFAULT_TO_ACCEPT #allow everything by default
624options IPV6FIREWALL #firewall for IPv6
625options IPV6FIREWALL_VERBOSE
626options IPV6FIREWALL_VERBOSE_LIMIT=100
627options IPV6FIREWALL_DEFAULT_TO_ACCEPT
628options IPDIVERT #divert sockets
629options IPFILTER #ipfilter support
630options IPFILTER_LOG #ipfilter logging
631options IPFILTER_DEFAULT_BLOCK #block all packets by default
632options IPSTEALTH #support for stealth forwarding
633options TCPDEBUG
634
02742ec6
JS
635device pf
636device pfsync
637device pflog
638
0d16ba1d
MD
639#CARP
640pseudo-device carp
641options CARP
642
984263bc
MD
643# The MBUF_STRESS_TEST option enables options which create
644# various random failures / extreme cases related to mbuf
645# functions. See the mbuf(9) manpage for a list of available
646# test cases.
647options MBUF_STRESS_TEST
648
984263bc
MD
649# Statically link in accept filters
650options ACCEPT_FILTER_DATA
651options ACCEPT_FILTER_HTTP
652
b1992928
MD
653# TCP_SIGNATURE adds support for RFC 2385 (TCP-MD5) digests. These are
654# carried in TCP option 19. This option is commonly used to protect
655# TCP sessions (e.g. BGP) where IPSEC is not available nor desirable.
656# This is enabled on a per-socket basis using the TCP_MD5SIG socket option.
657# This requires the use of 'device crypto', 'options IPSEC'
658# or 'device cryptodev'.
659options TCP_SIGNATURE #include support for RFC 2385
660
984263bc
MD
661#
662# TCP_DROP_SYNFIN adds support for ignoring TCP packets with SYN+FIN. This
663# prevents nmap et al. from identifying the TCP/IP stack, but breaks support
664# for RFC1644 extensions and is not recommended for web servers.
665#
666options TCP_DROP_SYNFIN #drop TCP packets with SYN+FIN
667
668# ICMP_BANDLIM enables icmp error response bandwidth limiting. You
669# typically want this option as it will help protect the machine from
670# D.O.S. packet attacks.
671#
672options ICMP_BANDLIM
673
674# DUMMYNET enables the "dummynet" bandwidth limiter. You need
675# IPFIREWALL as well. See the dummynet(4) and ipfw(8) manpages for more info.
984263bc 676#
984263bc 677options DUMMYNET
a951f6d4 678options DUMMYNET_DEBUG
984263bc
MD
679
680#
681# ATM (HARP version) options
682#
683# ATM_CORE includes the base ATM functionality code. This must be included
684# for ATM support.
685#
686# ATM_IP includes support for running IP over ATM.
687#
688# At least one (and usually only one) of the following signalling managers
689# must be included (note that all signalling managers include PVC support):
690# ATM_SIGPVC includes support for the PVC-only signalling manager `sigpvc'.
691# ATM_SPANS includes support for the `spans' signalling manager, which runs
692# the FORE Systems's proprietary SPANS signalling protocol.
693# ATM_UNI includes support for the `uni30' and `uni31' signalling managers,
694# which run the ATM Forum UNI 3.x signalling protocols.
695#
696# The `hea' driver provides support for the Efficient Networks, Inc.
697# ENI-155p ATM PCI Adapter.
698#
699# The `hfa' driver provides support for the FORE Systems, Inc.
700# PCA-200E ATM PCI Adapter.
701#
702options ATM_CORE #core ATM protocol family
703options ATM_IP #IP over ATM support
704options ATM_SIGPVC #SIGPVC signalling manager
705options ATM_SPANS #SPANS signalling manager
706options ATM_UNI #UNI signalling manager
707device hea #Efficient ENI-155p ATM PCI
708device hfa #FORE PCA-200E ATM PCI
709
710# DEVICE_POLLING adds support for mixed interrupt-polling handling
711# of network device drivers, which has significant benefits in terms
712# of robustness to overloads and responsivity, as well as permitting
713# accurate scheduling of the CPU time between kernel network processing
84bc65d9
TN
714# and other activities. The drawback is a moderate (up to 1/pollhz seconds)
715# potential increase in response times. See polling(4) for further details.
d856dabc 716#
984263bc
MD
717options DEVICE_POLLING
718
6792e4fa
SZ
719# IFPOLL_ENABLE adds hardware queues' based polling
720options IFPOLL_ENABLE
721
984263bc
MD
722\f
723#####################################################################
724# FILESYSTEM OPTIONS
725
726#
727# Only the root, /usr, and /tmp filesystems need be statically
728# compiled; everything else will be automatically loaded at mount
86fab417 729# time. (Exception: the UFS family --- FFS, and MFS ---
84bc65d9
TN
730# cannot currently be demand-loaded.) Some people still prefer
731# to statically compile other filesystems as well.
984263bc 732#
36a06697 733# NB: The PORTAL and UNION filesystems are known to be
984263bc
MD
734# buggy, and WILL panic your system if you attempt to do anything with
735# them. They are included here as an incentive for some enterprising
736# soul to sit down and fix them.
737#
738
739# One of these is mandatory:
740options FFS #Fast filesystem
4ab1cc4a
DR
741options MFS #Memory filesystem
742options NFS #Network filesystem
984263bc
MD
743
744# The rest are optional:
745#options NFS_NOSERVER #Disable the NFS-server code.
746options CD9660 #ISO 9660 filesystem
747options FDESC #File descriptor filesystem
4ab1cc4a
DR
748options MSDOSFS #MS DOS filesystem
749options NTFS #NT filesystem
36a06697 750options NULLFS #NULL filesystem
984263bc
MD
751options NWFS #NetWare filesystem
752options PORTAL #Portal filesystem
753options PROCFS #Process filesystem
754options SMBFS #SMB/CIFS filesystem
4a77c3ab 755options UDF #UDF filesystem
9daa0298 756options HAMMER #HAMMER filesystem
7a2de9a4 757options TMPFS #Temporary filesystem
9daa0298 758
03c6405b 759# YYY-DR Till we rework the VOP methods for this filesystem
03c6405b 760#options UNION #Union filesystem
984263bc 761# The xFS_ROOT options REQUIRE the associated ``options xFS''
984263bc
MD
762options FFS_ROOT #FFS usable as root device
763options NFS_ROOT #NFS usable as root device
764
84bc65d9 765# Soft updates is technique for improving UFS filesystem speed and
984263bc
MD
766# making abrupt shutdown less risky.
767options SOFTUPDATES
768
769# Directory hashing improves the speed of operations on very large
770# directories at the expense of some memory.
771options UFS_DIRHASH
772
773# Make space in the kernel for a root filesystem on a md device.
774# Define to the number of kilobytes to reserve for the filesystem.
775options MD_ROOT_SIZE=10
776
777# Make the md device a potential root device, either with preloaded
778# images of type mfs_root or md_root.
779options MD_ROOT
780
781# Specify double the default maximum size for malloc(9)-backed md devices.
782options MD_NSECT=40000
783
784# Allow this many swap-devices.
785#
786# In order to manage swap, the system must reserve bitmap space that
d856dabc 787# scales with the largest mounted swap device multiplied by NSWAPDEV,
531c762a 788# regardless of whether other swap devices exist or not. So it
984263bc
MD
789# is not a good idea to make this value too large.
790options NSWAPDEV=5
791
792# Disk quotas are supported when this option is enabled.
793options QUOTA #enable disk quotas
794
795# If you are running a machine just as a fileserver for PC and MAC
796# users, using SAMBA or Netatalk, you may consider setting this option
797# and keeping all those users' directories on a filesystem that is
798# mounted with the suiddir option. This gives new files the same
799# ownership as the directory (similar to group). It's a security hole
800# if you let these users run programs, so confine it to file-servers
801# (but it'll save you lots of headaches in those cases). Root owned
802# directories are exempt and X bits are cleared. The suid bit must be
803# set on the directory as well; see chmod(1) PC owners can't see/set
804# ownerships so they keep getting their toes trodden on. This saves
805# you all the support calls as the filesystem it's used on will act as
806# they expect: "It's my dir so it must be my file".
807#
808options SUIDDIR
809
810# NFS options:
811options NFS_MINATTRTIMO=3 # VREG attrib cache timeout in sec
812options NFS_MAXATTRTIMO=60
813options NFS_MINDIRATTRTIMO=30 # VDIR attrib cache timeout in sec
814options NFS_MAXDIRATTRTIMO=60
815options NFS_GATHERDELAY=10 # Default write gather delay (msec)
816options NFS_UIDHASHSIZ=29 # Tune the size of nfssvc_sock with this
817options NFS_WDELAYHASHSIZ=16 # and with this
818options NFS_MUIDHASHSIZ=63 # Tune the size of nfsmount with this
819options NFS_DEBUG # Enable NFS Debugging
820
0e63c0c7
SW
821# MSDOSFS options:
822options MSDOSFS_DEBUG # Enable MSDOSFS Debugging
823
984263bc
MD
824#
825# Add support for the EXT2FS filesystem of Linux fame. Be a bit
826# careful with this - the ext2fs code has a tendency to lag behind
827# changes and not be exercised very much, so mounting read/write could
828# be dangerous (and even mounting read only could result in panics.)
829#
830options EXT2FS
831
832# Use real implementations of the aio_* system calls. There are numerous
833# stability and security issues in the current aio code that make it
834# unsuitable for inclusion on machines with untrusted local users.
835options VFS_AIO
836
837\f
838#####################################################################
839# POSIX P1003.1B
840
841# Real time extensions added in the 1993 Posix
842# P1003_1B: Infrastructure
843# _KPOSIX_PRIORITY_SCHEDULING: Build in _POSIX_PRIORITY_SCHEDULING
844# _KPOSIX_VERSION: Version kernel is built for
845
846options P1003_1B
847options _KPOSIX_PRIORITY_SCHEDULING
848options _KPOSIX_VERSION=199309L
849
850\f
851#####################################################################
852# CLOCK OPTIONS
853
854# The granularity of operation is controlled by the kernel option HZ whose
855# default value (100) means a granularity of 10ms (1s/HZ).
984263bc
MD
856# Consider, however, that reducing the granularity too much might
857# cause excessive overhead in clock interrupt processing,
858# potentially causing ticks to be missed and thus actually reducing
859# the accuracy of operation.
860
861options HZ=100
862
863# The following options are used for debugging clock behavior only, and
864# should not be used for production systems.
d856dabc 865#
984263bc
MD
866# CLK_CALIBRATION_LOOP will run the clock calibration loop at startup
867# until the user presses a key.
868
869options CLK_CALIBRATION_LOOP
870
871# The following two options measure the frequency of the corresponding
872# clock relative to the RTC (onboard mc146818a).
873
874options CLK_USE_I8254_CALIBRATION
875options CLK_USE_TSC_CALIBRATION
876
877\f
878#####################################################################
879# SCSI DEVICES
880
881# SCSI DEVICE CONFIGURATION
882
883# The SCSI subsystem consists of the `base' SCSI code, a number of
884# high-level SCSI device `type' drivers, and the low-level host-adapter
885# device drivers. The host adapters are listed in the ISA and PCI
886# device configuration sections below.
887#
888# Beginning with FreeBSD 2.0.5 you can wire down your SCSI devices so
889# that a given bus, target, and LUN always come on line as the same
890# device unit. In earlier versions the unit numbers were assigned
891# in the order that the devices were probed on the SCSI bus. This
892# means that if you removed a disk drive, you may have had to rewrite
893# your /etc/fstab file, and also that you had to be careful when adding
894# a new disk as it may have been probed earlier and moved your device
895# configuration around.
896
897# This old behavior is maintained as the default behavior. The unit
898# assignment begins with the first non-wired down unit for a device
899# type. For example, if you wire a disk as "da3" then the first
900# non-wired disk will be assigned da4.
901
902# The syntax for wiring down devices is:
903
904# device scbus0 at ahc0 # Single bus device
905# device scbus1 at ahc1 bus 0 # Single bus device
906# device scbus3 at ahc2 bus 0 # Twin bus device
907# device scbus2 at ahc2 bus 1 # Twin bus device
908# device da0 at scbus0 target 0 unit 0
909# device da1 at scbus3 target 1
910# device da2 at scbus2 target 3
911# device sa1 at scbus1 target 6
912# device cd
913
914# "units" (SCSI logical unit number) that are not specified are
915# treated as if specified as LUN 0.
916
917# All SCSI devices allocate as many units as are required.
918
919# The "unknown" device (uk? in pre-2.0.5) is now part of the base SCSI
920# configuration and doesn't have to be explicitly configured.
921
922device scbus #base SCSI code
923device ch #SCSI media changers
924device da #SCSI direct access devices (aka disks)
925device sa #SCSI tapes
926device cd #SCSI CD-ROMs
927device pass #CAM passthrough driver
58c79c32 928device sg #Passthrough device (linux scsi generic)
984263bc
MD
929device pt #SCSI processor type
930device ses #SCSI SES/SAF-TE driver
931
61413047
AH
932# Options for device mapper
933device dm
7115a22b
AH
934device dm_target_crypt
935device dm_target_linear
936device dm_target_striped
61413047 937
e25c779e
MD
938# Options for iSCSI
939device iscsi_initiator
33805800 940options ISCSI_INITIATOR_DEBUG=8
e25c779e 941
984263bc
MD
942# CAM OPTIONS:
943# debugging options:
944# -- NOTE -- If you specify one of the bus/target/lun options, you must
945# specify them all!
946# CAMDEBUG: When defined enables debugging macros
947# CAM_DEBUG_BUS: Debug the given bus. Use -1 to debug all busses.
948# CAM_DEBUG_TARGET: Debug the given target. Use -1 to debug all targets.
949# CAM_DEBUG_LUN: Debug the given lun. Use -1 to debug all luns.
950# CAM_DEBUG_FLAGS: OR together CAM_DEBUG_INFO, CAM_DEBUG_TRACE,
951# CAM_DEBUG_SUBTRACE, and CAM_DEBUG_CDB
952#
953# CAM_MAX_HIGHPOWER: Maximum number of concurrent high power (start unit) cmds
954# SCSI_NO_SENSE_STRINGS: When defined disables sense descriptions
955# SCSI_NO_OP_STRINGS: When defined disables opcode descriptions
956# SCSI_DELAY: The number of MILLISECONDS to freeze the SIM (scsi adapter)
957# queue after a bus reset, and the number of milliseconds to
cf66c265
PA
958# freeze the device queue after a bus device reset. This
959# can be changed at boot and runtime with the
960# kern.cam.scsi_delay tunable/sysctl.
984263bc
MD
961options CAMDEBUG
962options CAM_DEBUG_BUS=-1
963options CAM_DEBUG_TARGET=-1
964options CAM_DEBUG_LUN=-1
965options CAM_DEBUG_FLAGS="CAM_DEBUG_INFO|CAM_DEBUG_TRACE|CAM_DEBUG_CDB"
966options CAM_MAX_HIGHPOWER=4
967options SCSI_NO_SENSE_STRINGS
968options SCSI_NO_OP_STRINGS
969options SCSI_DELAY=8000 # Be pessimistic about Joe SCSI device
970
971# Options for the CAM CDROM driver:
972# CHANGER_MIN_BUSY_SECONDS: Guaranteed minimum time quantum for a changer LUN
973# CHANGER_MAX_BUSY_SECONDS: Maximum time quantum per changer LUN, only
974# enforced if there is I/O waiting for another LUN
975# The compiled in defaults for these variables are 2 and 10 seconds,
976# respectively.
977#
978# These can also be changed on the fly with the following sysctl variables:
979# kern.cam.cd.changer.min_busy_seconds
980# kern.cam.cd.changer.max_busy_seconds
981#
982options CHANGER_MIN_BUSY_SECONDS=2
983options CHANGER_MAX_BUSY_SECONDS=10
984
985# Options for the CAM sequential access driver:
986# SA_IO_TIMEOUT: Timeout for read/write/wfm operations, in minutes
987# SA_SPACE_TIMEOUT: Timeout for space operations, in minutes
988# SA_REWIND_TIMEOUT: Timeout for rewind operations, in minutes
989# SA_ERASE_TIMEOUT: Timeout for erase operations, in minutes
990# SA_1FM_AT_EOD: Default to model which only has a default one filemark at EOT.
991options SA_IO_TIMEOUT="(4)"
992options SA_SPACE_TIMEOUT="(60)"
993options SA_REWIND_TIMEOUT="(2*60)"
994options SA_ERASE_TIMEOUT="(4*60)"
995options SA_1FM_AT_EOD
996
997# Optional timeout for the CAM processor target (pt) device
998# This is specified in seconds. The default is 60 seconds.
999options SCSI_PT_DEFAULT_TIMEOUT="60"
1000
1001# Optional enable of doing SES passthrough on other devices (e.g., disks)
1002#
1003# Normally disabled because a lot of newer SCSI disks report themselves
1004# as having SES capabilities, but this can then clot up attempts to build
1005# build a topology with the SES device that's on the box these drives
1006# are in....
1007options SES_ENABLE_PASSTHROUGH
1008
1009\f
1010#####################################################################
1011# MISCELLANEOUS DEVICES AND OPTIONS
1012
1013# The `pty' device usually turns out to be ``effectively mandatory'',
1014# as it is required for `telnetd', `rlogind', `screen', `emacs', and
1015# `xterm', among others.
1016
1017pseudo-device pty #Pseudo ttys
984263bc
MD
1018pseudo-device gzip #Exec gzipped a.out's
1019pseudo-device vn #Vnode driver (turns a file into a device)
1020pseudo-device md #Memory/malloc disk
1021pseudo-device snp #Snoop device - to look at pty/vty/etc..
1022pseudo-device ccd 4 #Concatenated disk driver
1023
1024# Configuring Vinum into the kernel is not necessary, since the kld
1025# module gets started automatically when vinum(8) starts. This
1026# device is also untested. Use at your own risk.
1027#
1028# The option VINUMDEBUG must match the value set in CFLAGS
1029# in src/sbin/vinum/Makefile. Failure to do so will result in
1030# the following message from vinum(8):
1031#
1032# Can't get vinum config: Invalid argument
1033#
1034# see vinum(4) for more reasons not to use these options.
02bda9cd 1035pseudo-device vinum #Vinum concat/mirror/raid driver
984263bc
MD
1036options VINUMDEBUG #enable Vinum debugging hooks
1037
1038# Kernel side iconv library
1039options LIBICONV
1040
1041# Size of the kernel message buffer. Should be N * pagesize.
1042options MSGBUF_SIZE=40960
1043
1044\f
1045#####################################################################
1046# HARDWARE DEVICE CONFIGURATION
1047
1048# ISA and EISA devices:
1049# EISA support is available for some device, so they can be auto-probed.
984263bc
MD
1050
1051#
1052# Mandatory ISA devices: isa, npx
1053#
1054device isa
1055
0e1cb2e2
JS
1056# ISA-PnP BIOS support
1057device pnpbios
1058
984263bc
MD
1059#
1060# Options for `isa':
1061#
1062# AUTO_EOI_1 enables the `automatic EOI' feature for the master 8259A
1063# interrupt controller. This saves about 0.7-1.25 usec for each interrupt.
1064# This option breaks suspend/resume on some portables.
1065#
1066# AUTO_EOI_2 enables the `automatic EOI' feature for the slave 8259A
1067# interrupt controller. This saves about 0.7-1.25 usec for each interrupt.
1068# Automatic EOI is documented not to work for for the slave with the
1069# original i8259A, but it works for some clones and some integrated
1070# versions.
1071#
1072# MAXMEM specifies the amount of RAM on the machine; if this is not
fc29bf55 1073# specified, DragonFly will first read the amount of memory from the CMOS
984263bc
MD
1074# RAM, so the amount of memory will initially be limited to 64MB or 16MB
1075# depending on the BIOS. If the BIOS reports 64MB, a memory probe will
1076# then attempt to detect the installed amount of RAM. If this probe
1077# fails to detect >64MB RAM you will have to use the MAXMEM option.
1078# The amount is in kilobytes, so for a machine with 128MB of RAM, it would
1079# be 131072 (128 * 1024).
1080#
1081# BROKEN_KEYBOARD_RESET disables the use of the keyboard controller to
1082# reset the CPU for reboot. This is needed on some systems with broken
1083# keyboard controllers.
984263bc 1084
66cc79ca 1085options COMPAT_OLDISA #FreeBSD 2.2 and 3.x compatibility shims
984263bc
MD
1086options AUTO_EOI_1
1087#options AUTO_EOI_2
1088options MAXMEM="(128*1024)"
1089#options BROKEN_KEYBOARD_RESET
984263bc
MD
1090
1091# Enable support for the kernel PLL to use an external PPS signal,
1092# under supervision of [x]ntpd(8)
1093# More info in ntpd documentation: http://www.eecis.udel.edu/~ntp
1094
1095options PPS_SYNC
1096
984263bc
MD
1097# The keyboard controller; it controls the keyboard and the PS/2 mouse.
1098device atkbdc0 at isa? port IO_KBD
1099
1100# The AT keyboard
1101device atkbd0 at atkbdc? irq 1
1102
1103# Options for atkbd:
1104options ATKBD_DFLT_KEYMAP # specify the built-in keymap
1105makeoptions ATKBD_DFLT_KEYMAP="jp.106"
1106
1107# These options are valid for other keyboard drivers as well.
1108options KBD_DISABLE_KEYMAP_LOAD # refuse to load a keymap
1109options KBD_INSTALL_CDEV # install a CDEV entry in /dev
1110
1111# `flags' for atkbd:
1112# 0x01 Force detection of keyboard, else we always assume a keyboard
1113# 0x02 Don't reset keyboard, useful for some newer ThinkPads
1114# 0x03 Force detection and avoid reset, might help with certain
1115# dockingstations
1116# 0x04 Old-style (XT) keyboard support, useful for older ThinkPads
1117
1118# PS/2 mouse
1119device psm0 at atkbdc? irq 12
1120
1121# Options for psm:
1122options PSM_HOOKRESUME #hook the system resume event, useful
1123 #for some laptops
1124options PSM_RESETAFTERSUSPEND #reset the device at the resume event
1125
07cf6114
SW
1126device kbdmux # keyboard multiplexer
1127
984263bc
MD
1128# The video card driver.
1129device vga0 at isa?
1130
1131# Options for vga:
1132# Try the following option if the mouse pointer is not drawn correctly
1133# or font does not seem to be loaded properly. May cause flicker on
1134# some systems.
1135options VGA_ALT_SEQACCESS
1136
9c06b297
SW
1137options VGA_DEBUG=2 # enable VGA debug output
1138
fb5d6e26
SW
1139# If you experience problems switching back to 80x25 (or a derived mode),
1140# the following option might help.
1141#options VGA_KEEP_POWERON_MODE # use power-on settings for 80x25
1142
984263bc
MD
1143# If you can dispense with some vga driver features, you may want to
1144# use the following options to save some memory.
6fbe6059
SW
1145#options VGA_NO_FONT_LOADING # don't save/load font
1146#options VGA_NO_MODE_CHANGE # don't change video modes
984263bc 1147
984263bc
MD
1148# The following option probably won't work with the LCD displays.
1149options VGA_WIDTH90 # support 90 column modes
1150
1151# To include support for VESA video modes
1152options VESA
9c06b297 1153options VESA_DEBUG=2 # enable VESA debug output
d856dabc 1154
984263bc
MD
1155# Splash screen at start up! Screen savers require this too.
1156pseudo-device splash
1157
984263bc
MD
1158# The syscons console driver (sco color console compatible).
1159device sc0 at isa?
1160options MAXCONS=16 # number of virtual consoles
1161options SC_ALT_MOUSE_IMAGE # simplified mouse cursor in text mode
9c06b297 1162options SC_DEBUG_LEVEL=5 # enable debug output
984263bc
MD
1163options SC_DFLT_FONT # compile font in
1164makeoptions SC_DFLT_FONT=cp850
1165options SC_DISABLE_DDBKEY # disable `debug' key
1166options SC_DISABLE_REBOOT # disable reboot key sequence
1167options SC_HISTORY_SIZE=200 # number of history buffer lines
1168options SC_MOUSE_CHAR=0x3 # char code for text mode mouse cursor
1169options SC_PIXEL_MODE # add support for the raster text mode
1170
1171# The following options will let you change the default colors of syscons.
1172options SC_NORM_ATTR="(FG_GREEN|BG_BLACK)"
1173options SC_NORM_REV_ATTR="(FG_YELLOW|BG_GREEN)"
1174options SC_KERNEL_CONS_ATTR="(FG_RED|BG_BLACK)"
1175options SC_KERNEL_CONS_REV_ATTR="(FG_BLACK|BG_RED)"
1176
1177# If you have a two button mouse, you may want to add the following option
1178# to use the right button of the mouse to paste text.
1179options SC_TWOBUTTON_MOUSE
1180
1181# You can selectively disable features in syscons.
6fbe6059
SW
1182#options SC_NO_CUTPASTE
1183#options SC_NO_FONT_LOADING
1184#options SC_NO_HISTORY
1185#options SC_NO_SYSMOUSE
984263bc
MD
1186
1187#
1188# The Numeric Processing eXtension driver. In addition to this, you
1189# may configure a math emulator (see above). If your machine has a
1190# hardware FPU and the kernel configuration includes the npx device
1191# *and* a math emulator compiled into the kernel, the hardware FPU
1192# will be used, unless it is found to be broken or unless "flags" to
1193# npx0 includes "0x08", which requests preference for the emulator.
1194device npx0 at nexus? port IO_NPX flags 0x0 irq 13
1195
1196#
1197# `flags' for npx0:
1198# 0x01 don't use the npx registers to optimize bcopy.
1199# 0x02 don't use the npx registers to optimize bzero.
1200# 0x04 don't use the npx registers to optimize copyin or copyout.
1201# 0x08 use emulator even if hardware FPU is available.
1202# The npx registers are normally used to optimize copying and zeroing when
1203# all of the following conditions are satisfied:
1204# I586_CPU is an option
1205# the cpu is an i586 (perhaps not a Pentium)
1206# the probe for npx0 succeeds
1207# INT 16 exception handling works.
1208# Then copying and zeroing using the npx registers is normally 30-100% faster.
1209# The flags can be used to control cases where it doesn't work or is slower.
1210# Setting them at boot time using userconfig works right (the optimizations
1211# are not used until later in the bootstrap when npx0 is attached).
1212# Flag 0x08 automatically disables the i586 optimized routines.
1213#
1214
1215#
1216# Optional ISA and EISA devices:
1217#
1218
1219#
1220# SCSI host adapters: `aha', `aic', `bt'
1221#
1222# adv: All Narrow SCSI bus AdvanSys controllers.
1223# adw: Second Generation AdvanSys controllers including the ADV940UW.
1224# aha: Adaptec 154x
1225# ahc: Adaptec 274x/284x/294x
1226# aic: Adaptec 152x
1227# bt: Most Buslogic controllers
1228# ncv: NCR 53C500 based SCSI host adapters.
1229# nsp: Workbit Ninja SCSI-3 based PC Card SCSI host adapters.
1230# stg: TMC 18C30, 18C50 based ISA/PC Card SCSI host adapters.
1231#
1232# Note that the order is important in order for Buslogic cards to be
1233# probed correctly.
1234#
1235
1236device bt0 at isa? port IO_BT0
1237device adv0 at isa?
1238device adw
1239device aha0 at isa?
1240device aic0 at isa?
1241device ncv
1242device nsp
1243device stg0 at isa? port 0x140 irq 11
1244
1245#
1246# Adaptec FSA RAID controllers, including integrated DELL controller,
1247# the Dell PERC 2/QC and the HP NetRAID-4M
1248#
1249device aac
09ccaff3 1250options AAC_DEBUG=4
984263bc
MD
1251device aacp # SCSI Passthrough interface (optional, CAM required)
1252
1253#
1254# Compaq Smart RAID, Mylex DAC960 and AMI MegaRAID controllers. Only
1255# one entry is needed; the code will find and configure all supported
1256# controllers.
1257#
1258device ida # Compaq Smart RAID
1259device mlx # Mylex DAC960
1260device amr # AMI MegaRAID
1fcd0ba2 1261device amrp # SCSI Passthrough interface (optional, CAM req.)
249d29c8
SW
1262device mfi # LSI MegaRAID SAS
1263device mfip # LSI MegaRAID SAS passthrough, requires CAM
1264options MFI_DEBUG
984263bc
MD
1265
1266#
9c57a36d 1267# Areca RAID (CAM is required).
1901a965
SW
1268#
1269device arcmsr # Areca SATA II RAID
1270
1271#
984263bc
MD
1272# 3ware ATA RAID
1273#
1274device twe # 3ware ATA RAID
df54c2f9 1275device twa # 3ware 9000 series PATA/SATA RAID
4ad6607f 1276options TWA_DEBUG=10 # enable debug messages
984263bc
MD
1277
1278#
e6f8991b
DR
1279# Promise Supertrack SX6000
1280#
1281device pst
1282
1283#
2114ec03
DR
1284# IBM ServeRAID
1285#
1286device ips
1287
1288#
984263bc 1289# The 'ATA' driver supports all ATA and ATAPI devices.
984263bc
MD
1290# You only need one "device ata" for it to find all
1291# PCI ATA/ATAPI devices on modern machines.
f203b3ea
SW
1292#device ata
1293#device atadisk # ATA disk drives
1294#device atapicd # ATAPI CDROM drives
1295#device atapifd # ATAPI floppy drives
1296#device atapist # ATAPI tape drives
1297#device atapicam # emulate ATAPI devices as SCSI ditto via CAM
984263bc 1298 # needs CAM to be present (scbus & pass)
a579f9bc
MD
1299# AHCI driver, this will override NATA for AHCI devices,
1300# both drivers may be included.
1301#
1302device ahci
1303
d856dabc 1304# SiI3124/3132 driver
7c5306ee
SW
1305#
1306device sili
1307
4068acee
TS
1308# The 'NATA' set of drivers are set to replace the previous ATA drivers,
1309# and this set of drivers is mutually exclusive with the old ones. This means,
1310# you can't have both at the same time!
f203b3ea
SW
1311device nata
1312device natadisk # ATA disk drives
1313device natapicd # ATAPI CD/DVD drives
1314device natapifd # ATAPI floppy drives
1315device natapist # ATAPI tape drives
1316device natapicam # ATAPI CAM layer emulation
1317device nataraid # support for ATA software RAID controllers
1318device natausb # ATA-over-USB support
984263bc 1319
84bc65d9 1320#The following options are valid on the ATA & NATA drivers:
984263bc
MD
1321#
1322# ATA_STATIC_ID: controller numbering is static (like the old driver)
1323# else the device numbers are dynamically allocated.
1324options ATA_STATIC_ID
1325
1326#
1327# For older non-PCI systems, these are the lines to use:
1328#device ata0 at isa? port IO_WD1 irq 14
1329#device ata1 at isa? port IO_WD2 irq 15
1330
1331#
984263bc
MD
1332# Standard floppy disk controllers: `fdc' and `fd'
1333#
1334device fdc0 at isa? port IO_FD1 irq 6 drq 2
1335#
1336# FDC_DEBUG enables floppy debugging. Since the debug output is huge, you
1337# gotta turn it actually on by setting the variable fd_debug with DDB,
1338# however.
1339options FDC_DEBUG
1340
1341device fd0 at fdc0 drive 0
1342device fd1 at fdc0 drive 1
1343
984263bc
MD
1344#
1345# Other standard PC hardware: `mse', `sio', etc.
1346#
1347# mse: Logitech and ATI InPort bus mouse ports
1348# sio: serial ports (see sio(4))
1349
1350device mse0 at isa? port 0x23c irq 5
1351
1352device sio0 at isa? port IO_COM1 flags 0x10 irq 4
1353
1354#
1355# `flags' for serial drivers that support consoles (only for sio now):
1356# 0x10 enable console support for this unit. The other console flags
1357# are ignored unless this is set. Enabling console support does
1358# not make the unit the preferred console - boot with -h or set
1359# the 0x20 flag for that. Currently, at most one unit can have
1360# console support; the first one (in config file order) with
1361# this flag set is preferred. Setting this flag for sio0 gives
1362# the old behaviour.
1363# 0x20 force this unit to be the console (unless there is another
1364# higher priority console). This replaces the COMCONSOLE option.
1365# 0x40 reserve this unit for low level console operations. Do not
1366# access the device in any normal way.
1367# 0x80 use this port for serial line gdb support in ddb.
1368#
1369# PnP `flags' (set via userconfig using pnp x flags y)
1370# 0x1 disable probing of this device. Used to prevent your modem
1371# from being attached as a PnP modem.
1372#
1373
1374# Options for serial drivers that support consoles (only for sio now):
1375options BREAK_TO_DEBUGGER #a BREAK on a comconsole goes to
1376 #DDB, if available.
1377options CONSPEED=115200 # speed for serial console
1378 # (default 9600)
1379
1380# Solaris implements a new BREAK which is initiated by a character
1381# sequence CR ~ ^b which is similar to a familiar pattern used on
1382# Sun servers by the Remote Console.
1383options ALT_BREAK_TO_DEBUGGER
1384
1385# Options for sio:
1386options COM_ESP #code for Hayes ESP
1387options COM_MULTIPORT #code for some cards with shared IRQs
1388
1389# Other flags for sio that aren't documented in the man page.
1390# 0x20000 enable hardware RTS/CTS and larger FIFOs. Only works for
1391# ST16650A-compatible UARTs.
1392
1393# PCI Universal Communications driver
1394# Supports various single and multi port PCI serial cards. Maybe later
1395# also the parallel ports on combination serial/parallel cards. New cards
fc29bf55 1396# can be added in src/sys/dev/misc/puc/pucdata.c.
984263bc 1397device puc
984263bc
MD
1398
1399#
9e2b517e 1400# Network interfaces: `ed', `el', `ep', `ie', `is', `le', `lnc'
984263bc
MD
1401#
1402# ar: Arnet SYNC/570i hdlc sync 2/4 port V.35/X.21 serial driver (requires sppp)
984263bc 1403# cs: IBM Etherjet and other Crystal Semi CS89x0-based adapters
984263bc
MD
1404# ed: Western Digital and SMC 80xx; Novell NE1000 and NE2000; 3Com 3C503
1405# el: 3Com 3C501 (slow!)
1406# ep: 3Com 3C509
1407# ex: Intel EtherExpress Pro/10 and other i82595-based adapters
1408# fe: Fujitsu MB86960A/MB86965A Ethernet
1409# ie: AT&T StarLAN 10 and EN100; 3Com 3C507; unknown NI5210; Intel EtherExpress
1410# le: Digital Equipment EtherWorks 2 and EtherWorks 3 (DEPCA, DE100,
1411# DE101, DE200, DE201, DE202, DE203, DE204, DE205, DE422)
1412# lnc: Lance/PCnet cards (Isolan, Novell NE2100, NE32-VL, AMD Am7990 & Am79C960)
1413# rdp: RealTek RTL 8002-based pocket ethernet adapters
1414# sbni: Granch SBNI12-xx adapters
1415# sbsh: Granch SBNI16 SHDSL modem PCI adapters
1416# sr: RISCom/N2 hdlc sync 1/2 port V.35/X.21 serial driver (requires sppp)
1417# wl: Lucent Wavelan (ISA card only).
984263bc
MD
1418# wi: Lucent WaveLAN/IEEE 802.11 PCMCIA adapters. Note: this supports both
1419# the PCMCIA and ISA cards: the ISA card is really a PCMCIA to ISA
1420# bridge with a PCMCIA adapter plugged into it.
1421# an: Aironet 4500/4800 802.11 wireless adapters. Supports the PCMCIA,
1422# PCI and ISA varieties.
1423# xe: Xircom/Intel EtherExpress Pro100/16 PC Card ethernet controller.
984263bc
MD
1424#
1425device ar0 at isa? port 0x300 irq 10 iomem 0xd0000
984263bc 1426device cs0 at isa? port 0x300
984263bc
MD
1427device ed0 at isa? port 0x280 irq 5 iomem 0xd8000
1428device el0 at isa? port 0x300 irq 9
1429device ep
1430device ex
1431device fe0 at isa? port 0x300
1432device ie0 at isa? port 0x300 irq 5 iomem 0xd0000
1433device ie1 at isa? port 0x360 irq 7 iomem 0xd0000
1434device le0 at isa? port 0x300 irq 5 iomem 0xd0000
1435device lnc0 at isa? port 0x280 irq 10 drq 0
1436device rdp0 at isa? port 0x378 irq 7 flags 2
1437device sbni0 at isa? port 0x210 irq 5 flags 0xefdead
3fabb142 1438device sln
8b1bfc35 1439device sr
984263bc 1440device sn0 at isa? port 0x300 irq 10
d8a8ea86
JR
1441
1442# Wlan support is mandatory for some wireless LAN devices.
98091aa8
SW
1443options IEEE80211_DEBUG #enable debugging msgs
1444options IEEE80211_AMPDU_AGE #age frames in AMPDU reorder q's
1445options IEEE80211_SUPPORT_MESH #enable 802.11s D3.0 support
1446options IEEE80211_SUPPORT_TDMA #enable TDMA support
841ab66c
SZ
1447device wlan # 802.11 support
1448device wlan_acl # 802.11 MAC-based access control for AP
1449device wlan_ccmp # 802.11 CCMP support
1450device wlan_tkip # 802.11 TKIP support
1451device wlan_wep # 802.11 WEP support
1452device wlan_xauth # 802.11 WPA or 802.1x authentication for AP
e15de849 1453device wlan_amrr # 802.11 AMRR TX rate control algorithm
984263bc
MD
1454options WLCACHE # enables the signal-strength cache
1455options WLDEBUG # enables verbose debugging output
d8a8ea86 1456device an # Aironet Communications 4500/4800
54170488 1457device ath # Atheros AR521x
e0f55c69 1458options AH_SUPPORT_AR5416
54170488
SW
1459device ath_hal # Atheros Hardware Access Layer
1460#device ath_rate_amrr # Atheros AMRR TX rate control algorithm
1461#device ath_rate_onoe # Atheros Onoe TX rate control algorithm
1462device ath_rate_sample # Atheros Sample TX rate control algorithm
1463options ATH_DEBUG # turn on debugging output (see hw.ath.debug)
1464options ATH_DIAGAPI # diagnostic interface to the HAL
1465options ATH_RXBUF=80 # number of RX buffers to allocate
1466options ATH_TXBUF=400 # number of TX buffers to allocate
5c32bcdd 1467#device iwl # Intel PRO/Wireless 2100
1d97534a 1468device iwi # Intel PRO/Wireless 2200BG/2915ABG
8f13cc2d 1469device iwn # Intel WiFi Link 4965/1000/5000/5150/5300/6000/6050
d8a8ea86 1470device wi # WaveLAN/IEEE, PRISM-II, Spectrum24 802.11DS
5c32bcdd
RP
1471#device rtw # RealTek 8180
1472#device acx # TI ACX100/ACX111.
d8a8ea86
JR
1473device wl0 at isa? port 0x300 # T1 speed ISA/radio lan
1474device xe # Xircom PCMCIA
5fdff524 1475device ral # Ralink Technology 802.11 wireless NIC
f37bbeda 1476device wpi
984263bc 1477
da226b53
SW
1478# IEEE 802.11 adapter firmware modules
1479
1480# iwifw: Intel PRO/Wireless 2200BG/2225BG/2915ABG firmware
8f13cc2d 1481# iwnfw: Intel WiFi Link 4965/1000/5000/5150/5300/6000/6050
da226b53
SW
1482# ralfw: Ralink Technology RT25xx and RT26xx firmware
1483# wpifw: Intel 3945ABG Wireless LAN Controller firmware
1484
1485device iwifw
8f13cc2d 1486device iwnfw
da226b53
SW
1487device ralfw
1488device wpifw
1489
22012581
SW
1490# Bluetooth Protocols
1491device bluetooth
1492
984263bc
MD
1493#
1494# ATM related options
1495#
1496# The `en' device provides support for Efficient Networks (ENI)
1497# ENI-155 PCI midway cards, and the Adaptec 155Mbps PCI ATM cards (ANA-59x0).
1498#
1499# atm pseudo-device provides generic atm functions and is required for
1500# atm devices.
1501# NATM enables the netnatm protocol family that can be used to
1502# bypass TCP/IP.
1503#
1504# the current driver supports only PVC operations (no atm-arp, no multicast).
1505# for more details, please read the original documents at
1506# http://www.ccrc.wustl.edu/pub/chuck/tech/bsdatm/bsdatm.html
1507#
1508pseudo-device atm
1509device en
1510options NATM #native ATM
1511
e798f335 1512# Sound drivers
984263bc
MD
1513#
1514# The flags of the device tells the device a bit more info about the
1515# device that normally is obtained through the PnP interface.
1516# bit 2..0 secondary DMA channel;
1517# bit 4 set if the board uses two dma channels;
1518# bit 15..8 board type, overrides autodetection; leave it
1519# zero if don't know what to put in (and you don't,
1520# since this is unsupported at the moment...).
1521#
e798f335
JS
1522# This driver will use the new PnP code if it's available. You might
1523# need PNPBIOS for ISA devices.
984263bc 1524#
984263bc
MD
1525# If you have a GUS-MAX card and want to use the CS4231 codec on the
1526# card the drqs for the gus max must be 8 bit (1, 2, or 3).
1527#
1528# If you would like to use the full duplex option on the gus, then define
1529# flags to be the ``read dma channel''.
1530#
984263bc 1531
558a398b 1532# Basic sound card support:
984263bc 1533device pcm
6ceb4487 1534# For PnP/PCI sound cards:
e2339ccc 1535device "snd_ad1816"
558a398b
SS
1536device "snd_als4000"
1537device "snd_atiixp"
1538device "snd_cmi"
1539device "snd_cs4281"
1540device "snd_csa"
1541device "snd_ds1"
1542device "snd_emu10k1"
1543device "snd_es137x"
e2339ccc 1544device "snd_ess"
558a398b 1545device "snd_fm801"
e2339ccc 1546device "snd_hda"
558a398b
SS
1547device "snd_ich"
1548device "snd_maestro"
1549device "snd_maestro3"
e2339ccc 1550device "snd_mss"
558a398b 1551device "snd_neomagic"
e2339ccc
SW
1552device "snd_sb16"
1553device "snd_sb8"
1554device "snd_sbc"
558a398b
SS
1555device "snd_solo"
1556device "snd_t4dwave"
1557device "snd_via8233"
1558device "snd_via82c686"
1559device "snd_vibes"
e798f335 1560# For non-pnp sound cards:
558a398b 1561device pcm0 at isa? irq 10 drq 1 flags 0x0
e2339ccc 1562# USB
558a398b 1563device "snd_uaudio"
984263bc 1564
984263bc
MD
1565#
1566# Miscellaneous hardware:
1567#
984263bc
MD
1568# wt: Wangtek and Archive QIC-02/QIC-36 tape drives
1569# ctx: Cortex-I frame grabber
1570# apm: Laptop Advanced Power Management (experimental)
1571# spigot: The Creative Labs Video Spigot video-acquisition board
1572# meteor: Matrox Meteor video capture board
1573# bktr: Brooktree bt848/848a/849a/878/879 video capture and TV Tuner board
1574# cy: Cyclades serial driver
1575# dgb: Digiboard PC/Xi and PC/Xe series driver (ALPHA QUALITY!)
1576# dgm: Digiboard PC/Xem driver
1577# gp: National Instruments AT-GPIB and AT-GPIB/TNT board
1578# asc: GI1904-based hand scanners, e.g. the Trust Amiscan Grey
1579# gsc: Genius GS-4500 hand scanner.
1580# joy: joystick
1581# labpc: National Instrument's Lab-PC and Lab-PC+
1582# rc: RISCom/8 multiport card
1583# rp: Comtrol Rocketport(ISA) - single card
1584# tw: TW-523 power line interface for use with X-10 home control products
1585# si: Specialix SI/XIO 4-32 port terminal multiplexor
1586# spic: Sony Programmable I/O controller (VAIO notebooks)
1587# stl: Stallion EasyIO and EasyConnection 8/32 (ISA and PCI), EasyConnection 8/64 PCI
1588# stli: Stallion EasyConnection 8/64 ISA/EISA, ONboard, Brumby (intelligent)
1589# nmdm: nullmodem terminal driver (see nmdm(4))
1590
1591# Notes on APM
1592# The flags takes the following meaning for apm0:
1593# 0x0020 Statclock is broken.
1594# If apm is omitted, some systems require sysctl -w kern.timecounter.method=1
1595# for correct timekeeping.
1596
1597# Notes on the spigot:
1598# The video spigot is at 0xad6. This port address can not be changed.
1599# The irq values may only be 10, 11, or 15
1600# I/O memory is an 8kb region. Possible values are:
1601# 0a0000, 0a2000, ..., 0fffff, f00000, f02000, ..., ffffff
1602# The start address must be on an even boundary.
1603# Add the following option if you want to allow non-root users to be able
1604# to access the spigot. This option is not secure because it allows users
1605# direct access to the I/O page.
1606# options SPIGOT_UNSECURE
1607
1608# Notes on the Comtrol Rocketport driver:
1609#
1610# The exact values used for rp0 depend on how many boards you have
1611# in the system. The manufacturer's sample configs are listed as:
1612#
1613# Comtrol Rocketport ISA single card
1614# device rp0 at isa? port 0x280
1615#
1616# If instead you have two ISA cards, one installed at 0x100 and the
1617# second installed at 0x180, then you should add the following to
1618# your kernel configuration file:
1619#
1620# device rp0 at isa? port 0x100
1621# device rp1 at isa? port 0x180
1622#
1623# For 4 ISA cards, it might be something like this:
1624#
1625# device rp0 at isa? port 0x180
1626# device rp1 at isa? port 0x100
1627# device rp2 at isa? port 0x340
1628# device rp3 at isa? port 0x240
1629#
1630# And for PCI cards, you only need say:
1631#
1632# device rp
1633
1634# Notes on the Digiboard driver:
1635#
1636# The following flag values have special meanings:
1637# 0x01 - alternate layout of pins (dgb & dgm)
1638# 0x02 - use the windowed PC/Xe in 64K mode (dgb only)
1639
1640# Notes on the Specialix SI/XIO driver:
1641# **This is NOT a Specialix supported Driver!**
1642# The host card is memory, not IO mapped.
1643# The Rev 1 host cards use a 64K chunk, on a 32K boundary.
1644# The Rev 2 host cards use a 32K chunk, on a 32K boundary.
1645# The cards can use an IRQ of 11, 12 or 15.
1646
1647# Notes on the Stallion stl and stli drivers:
fc29bf55 1648# See src/sys/platform/pc32/isa/README.stl for complete instructions.
984263bc
MD
1649# This is version 2.0.0, unsupported by Stallion.
1650# The stl driver has a secondary IO port hard coded at 0x280. You need
fc29bf55 1651# to change src/sys/dev/serial/stl/stallion.c if you reconfigure this on the boards.
984263bc
MD
1652# The "flags" and "iosiz" settings on the stli driver depend on the board:
1653# EasyConnection 8/64 ISA: flags 23 iosiz 0x1000
1654# EasyConnection 8/64 EISA: flags 24 iosiz 0x10000
984263bc
MD
1655# ONboard ISA: flags 4 iosiz 0x10000
1656# ONboard EISA: flags 7 iosiz 0x10000
984263bc
MD
1657# Brumby: flags 2 iosiz 0x4000
1658# Stallion: flags 1 iosiz 0x10000
1659# For the PCI cards, "device stl" will suffice.
1660
984263bc
MD
1661# for the SoundBlaster 16 multicd - up to 4 devices
1662device wt0 at isa? port 0x300 irq 5 drq 1
1663device ctx0 at isa? port 0x230 iomem 0xd0000
1664device spigot0 at isa? port 0xad6 irq 15 iomem 0xee000
1665device apm0
1666device gp0 at isa? port 0x2c0
1667device gsc0 at isa? port IO_GSC1 drq 3
1668device joy0 at isa? port IO_GAME
1669device cy0 at isa? irq 10 iomem 0xd4000 iosiz 0x2000
49ec7c3b
JS
1670#device dgb0 at isa? port 0x220 iomem 0xfc000
1671#options NDGBPORTS=16 # Defaults to 16*NDGB
984263bc
MD
1672device dgm0 at isa? port 0x104 iomem 0xd0000
1673device labpc0 at isa? port 0x260 irq 5
1674device rc0 at isa? port 0x220 irq 12
49ec7c3b
JS
1675device nrp
1676#device rp0 at isa? port 0x280
984263bc
MD
1677# the port and irq for tw0 are fictitious
1678device tw0 at isa? port 0x380 irq 11
1679device si0 at isa? iomem 0xd0000 irq 12
1680device asc0 at isa? port IO_ASC1 drq 3 irq 10
1681device spic0 at isa? irq 0 port 0x10a0
1682device stl0 at isa? port 0x2a0 irq 10
1683device stli0 at isa? port 0x2a0 iomem 0xcc000 flags 23 iosiz 0x1000
984263bc
MD
1684# nullmodem terminal driver
1685device nmdm
1686
1687#
984263bc
MD
1688# EISA devices:
1689#
1690# The EISA bus device is `eisa'. It provides auto-detection and
1691# configuration support for all devices on the EISA bus.
1692#
1693# The `ahb' device provides support for the Adaptec 174X adapter.
1694#
1695# The `ahc' device provides support for the Adaptec 274X and 284X
1696# adapters. The 284X, although a VLB card, responds to EISA probes.
984263bc
MD
1697device eisa
1698device ahb
1699device ahc
984263bc
MD
1700
1701# The aic7xxx driver will attempt to use memory mapped I/O for all PCI
1702# controllers that have it configured only if this option is set. Unfortunately,
1703# this doesn't work on some motherboards, which prevents it from being the
1704# default.
1705options AHC_ALLOW_MEMIO
1706
1707# The adw driver will attempt to use memory mapped I/O for all PCI
1708# controllers that have it configured only if this option is set.
1709options ADW_ALLOW_MEMIO
1710
1711# By default, only 10 EISA slots are probed, since the slot numbers
1712# above clash with the configuration address space of the PCI subsystem,
1713# and the EISA probe is not very smart about this. This is sufficient
1714# for most machines, but in particular the HP NetServer LC series comes
1715# with an onboard AIC7770 dual-channel SCSI controller on EISA slot #11,
1716# thus you need to bump this figure to 12 for them.
1717options EISA_SLOTS=12
1718
1719#
1720# PCI devices & PCI options:
1721#
1722# The main PCI bus device is `pci'. It provides auto-detection and
1723# configuration support for all devices on the PCI bus, using either
1724# configuration mode defined in the PCI specification.
1725
1726device pci
1727
1728# PCI options
1729#
d856dabc 1730#Enable pci resources left off by a "lazy" BIOS.
7fe5a2bd 1731#
dc5a7bd2 1732options COMPAT_OLDPCI #FreeBSD 2.2 and 3.x compatibility shims
984263bc
MD
1733
1734# AGP GART support
1735#
1736device agp
1737
1738
1739# The `ahc' device provides support for the Adaptec 29/3940(U)(W)
1740# and motherboard based AIC7870/AIC7880 adapters.
4ad6607f
SW
1741options AHC_DEBUG
1742options AHC_DEBUG_OPTS=0xffffffff
1743options AHC_REG_PRETTY_PRINT
1744options AHC_TMODE_ENABLE
984263bc
MD
1745#
1746# The 'ahd' device provides support for the Adaptec 79xx Ultra320
1747# SCSI adapters. Options are documented in the ahd(4) manpage:
1748options AHD_DEBUG
1749options AHD_DEBUG_OPTS=0xffffffff
1750options AHD_REG_PRETTY_PRINT
1751#options AHD_TMODE_ENABLE=0xff
1752#
1753# The `amd' device provides support for the AMD 53C974 SCSI host
1754# adapter chip as found on devices such as the Tekram DC-390(T).
1755#
1756# The `bge' device provides support for gigabit ethernet adapters
3f625015 1757# based on the Broadcom BCM570x family of controllers, including the
984263bc
MD
1758# 3Com 3c996-T, the Netgear GA302T, the SysKonnect SK-9D21 and SK-9D41,
1759# and the embedded gigE NICs on Dell PowerEdge 2550 servers.
1760#
1761# The `ncr' device provides support for the NCR 53C810 and 53C825
1762# self-contained SCSI host adapters.
1763#
1764# The `isp' device provides support for the Qlogic ISP 1020, 1040
1765# nd 1040B PCI SCSI host adapters, ISP 1240 Dual Ultra SCSI,
1766# ISP 1080 and 1280 (Dual) Ultra2, ISP 12160 Ultra3 SCSI, as well as
1767# the Qlogic ISP 2100 and ISP 2200 Fibre Channel Host Adapters.
1768#
1769# The `dc' device provides support for PCI fast ethernet adapters
1770# based on the DEC/Intel 21143 and various workalikes including:
1771# the ADMtek AL981 Comet and AN985 Centaur, the ASIX Electronics
1772# AX88140A and AX88141, the Davicom DM9100 and DM9102, the Lite-On
1773# 82c168 and 82c169 PNIC, the Lite-On/Macronix LC82C115 PNIC II
1774# and the Macronix 98713/98713A/98715/98715A/98725 PMAC. This driver
1775# replaces the old al, ax, dm, pn and mx drivers. List of brands:
d856dabc
TN
1776# Digital DE500-BA, Kingston KNE100TX, D-Link DFE-570TX, SOHOware SFA110,
1777# SVEC PN102-TX, CNet Pro110B, 120A, and 120B, Compex RL100-TX,
984263bc
MD
1778# LinkSys LNE100TX, LNE100TX V2.0, Jaton XpressNet, Alfa Inc GFC2204,
1779# KNE110TX.
1780#
1781# The `de' device provides support for the Digital Equipment DC21040
1782# self-contained Ethernet adapter.
1783#
1784# The `em' device provides support for the Intel Pro/1000 Family of Gigabit
1785# adapters (82542, 82543, 82544, 82540).
1786#
d217d4d9
SZ
1787# The `et' device provides support for the Agere ET1310 10/100/1000 PCIe
1788# adapters.
1789#
984263bc
MD
1790# The `fxp' device provides support for the Intel EtherExpress Pro/100B
1791# PCI Fast Ethernet adapters.
1792#
984263bc
MD
1793# The 'lge' device provides support for PCI gigabit ethernet adapters
1794# based on the Level 1 LXT1001 NetCellerator chipset. This includes the
1795# D-Link DGE-500SX, SMC TigerCard 1000 (SMC9462SX), and some Addtron cards.
1796#
1797# The 'my' device provides support for the Myson MTD80X and MTD89X PCI
1798# Fast Ethernet adapters.
1799#
1800# The 'nge' device provides support for PCI gigabit ethernet adapters
1801# based on the National Semiconductor DP83820 and DP83821 chipset. This
1802# includes the SMC EZ Card 1000 (SMC9462TX), D-Link DGE-500T, Asante
1803# FriendlyNet GigaNIX 1000TA and 1000TPC, the Addtron AEG320T, the
1804# LinkSys EG1032 and EG1064, the Surecom EP-320G-TX and the Netgear GA622T.
1805#
1806# The 'pcn' device provides support for PCI fast ethernet adapters based
1807# on the AMD Am79c97x chipsets, including the PCnet/FAST, PCnet/FAST+,
1808# PCnet/PRO and PCnet/Home. These were previously handled by the lnc
1809# driver (and still will be if you leave this driver out of the kernel).
1810#
44ac28ea
JS
1811# Te 're' device provides support for PCI GigaBit ethernet adapters based
1812# on the RealTek 8169 chipset. It also supports the 8139C+ and is the
56be8454 1813# preferred driver for that chip.
44ac28ea 1814#
984263bc
MD
1815# The 'rl' device provides support for PCI fast ethernet adapters based
1816# on the RealTek 8129/8139 chipset. Note that the RealTek driver defaults
1817# to using programmed I/O to do register accesses because memory mapped
1818# mode seems to cause severe lockups on SMP hardware. This driver also
1819# supports the Accton EN1207D `Cheetah' adapter, which uses a chip called
1820# the MPX 5030/5038, which is either a RealTek in disguise or a RealTek
1821# workalike. Note that the D-Link DFE-530TX+ uses the RealTek chipset
1822# and is supported by this driver, not the 'vr' driver.
1823#
1824# The 'sf' device provides support for Adaptec Duralink PCI fast
1825# ethernet adapters based on the Adaptec AIC-6915 "starfire" controller.
1826# This includes dual and quad port cards, as well as one 100baseFX card.
1827# Most of these are 64-bit PCI devices, except for one single port
1828# card which is 32-bit.
1829#
1830# The 'ste' device provides support for adapters based on the Sundance
1831# Technologies ST201 PCI fast ethernet controller. This includes the
1832# D-Link DFE-550TX.
1833#
1834# The 'sis' device provides support for adapters based on the Silicon
1835# Integrated Systems SiS 900 and SiS 7016 PCI fast ethernet controller
1836# chips.
1837#
1838# The 'sk' device provides support for the SysKonnect SK-984x series
1839# PCI gigabit ethernet NICs. This includes the SK-9841 and SK-9842
1840# single port cards (single mode and multimode fiber) and the
1841# SK-9843 and SK-9844 dual port cards (also single mode and multimode).
1842# The driver will autodetect the number of ports on the card and
1843# attach each one as a separate network interface.
1844#
1845# The 'ti' device provides support for PCI gigabit ethernet NICs based
1846# on the Alteon Networks Tigon 1 and Tigon 2 chipsets. This includes the
1847# Alteon AceNIC, the 3Com 3c985, the Netgear GA620 and various others.
1848# Note that you will probably want to bump up NMBCLUSTERS a lot to use
1849# this driver.
1850#
1851# The 'tl' device provides support for the Texas Instruments TNETE100
1852# series 'ThunderLAN' cards and integrated ethernet controllers. This
1853# includes several Compaq Netelligent 10/100 cards and the built-in
1854# ethernet controllers in several Compaq Prosignia, Proliant and
1855# Deskpro systems. It also supports several Olicom 10Mbps and 10/100
1856# boards.
1857#
1858# The `tx' device provides support for the SMC 9432 TX, BTX and FTX cards.
1859#
1860# The `txp' device provides support for the 3Com 3cR990 "Typhoon"
1861# 10/100 adapters.
1862#
1863# The `vr' device provides support for various fast ethernet adapters
1864# based on the VIA Technologies VT3043 `Rhine I' and VT86C100A `Rhine II'
d856dabc 1865# chips, including the D-Link DFE530TX (see 'rl' for DFE530TX+), the Hawking
984263bc
MD
1866# Technologies PN102TX, and the AOpen/Acer ALN-320.
1867#
1868# The `vx' device provides support for the 3Com 3C590 and 3C595
1869# early support
1870#
1871# The `wb' device provides support for various fast ethernet adapters
1872# based on the Winbond W89C840F chip. Note: this is not the same as
1873# the Winbond W89C940F, which is an NE2000 clone.
1874#
984263bc
MD
1875# The `xl' device provides support for the 3Com 3c900, 3c905 and
1876# 3c905B (Fast) Etherlink XL cards and integrated controllers. This
1877# includes the integrated 3c905B-TX chips in certain Dell Optiplex and
1878# Dell Precision desktop machines and the integrated 3c905-TX chips
1879# in Dell Latitude laptop docking stations.
1880#
984263bc
MD
1881# The `meteor' device is a PCI video capture board. It can also have the
1882# following options:
1883# options METEOR_ALLOC_PAGES=xxx preallocate kernel pages for data entry
1884# figure (ROWS*COLUMN*BYTES_PER_PIXEL*FRAME+PAGE_SIZE-1)/PAGE_SIZE
1885# options METEOR_DEALLOC_PAGES remove all allocated pages on close(2)
1886# options METEOR_DEALLOC_ABOVE=xxx remove all allocated pages above the
1887# specified amount. If this value is below the allocated amount no action
1888# taken
1889# options METEOR_SYSTEM_DEFAULT={METEOR_PAL|METEOR_NTSC|METEOR_SECAM}, used
1890# for initialization of fps routine when a signal is not present.
1891#
1892# The 'bktr' device is a PCI video capture device using the Brooktree
1893# bt848/bt848a/bt849a/bt878/bt879 chipset. When used with a TV Tuner it forms a
1894# TV card, eg Miro PC/TV, Hauppauge WinCast/TV WinTV, VideoLogic Captivator,
1895# Intel Smart Video III, AverMedia, IMS Turbo, FlyVideo.
1896#
1897# options OVERRIDE_CARD=xxx
1898# options OVERRIDE_TUNER=xxx
1899# options OVERRIDE_MSP=1
1900# options OVERRIDE_DBX=1
1901# These options can be used to override the auto detection
fc29bf55 1902# The current values for xxx are found in src/sys/dev/video/bktr/bktr_card.h
984263bc
MD
1903# Using sysctl(8) run-time overrides on a per-card basis can be made
1904#
4ad6607f 1905# options BKTR_SYSTEM_DEFAULT=BROOKTREE_PAL
984263bc 1906# or
4ad6607f 1907# options BKTR_SYSTEM_DEFAULT=BROOKTREE_NTSC
984263bc
MD
1908# Specifes the default video capture mode.
1909# This is required for Dual Crystal (28&35Mhz) boards where PAL is used
1910# to prevent hangs during initialisation. eg VideoLogic Captivator PCI.
1911#
1912# options BKTR_USE_PLL
1913# PAL or SECAM users who have a 28Mhz crystal (and no 35Mhz crystal)
1914# must enable PLL mode with this option. eg some new Bt878 cards.
1915#
1916# options BKTR_GPIO_ACCESS
1917# This enable IOCTLs which give user level access to the GPIO port.
1918#
1919# options BKTR_NO_MSP_RESET
1920# Prevents the MSP34xx reset. Good if you initialise the MSP in another OS first
1921#
1922# options BKTR_430_FX_MODE
1923# Switch Bt878/879 cards into Intel 430FX chipset compatibility mode.
1924#
1925# options BKTR_SIS_VIA_MODE
1926# Switch Bt878/879 cards into SIS/VIA chipset compatibility mode which is
1927# needed for some old SiS and VIA chipset motherboards.
1928# This also allows Bt878/879 chips to work on old OPTi (<1997) chipset
1929# motherboards and motherboards with bad or incomplete PCI 2.1 support.
1930# As a rough guess, old = before 1998
1931#
a35cc233
JS
1932# options BKTR_NEW_MSP34XX_DRIVER
1933# Use new, more complete initialization scheme for the msp34* soundchip.
1934# Should fix stereo autodetection if the old driver does only output
1935# mono sound.
1936#
4ad6607f
SW
1937# options BKTR_OVERRIDE_CARD=xxx
1938# options BKTR_OVERRIDE_DBX=xxx
1939# options BKTR_OVERRIDE_MSP=xxx
1940# options BKTR_OVERRIDE_TUNER=xxx
1941# These options can be used to select a specific device, regardless of
1942# the autodetection and i2c device checks (see comments in bktr_card.c).
1943#
984263bc
MD
1944device ahc # AHA2940 and onboard AIC7xxx devices
1945device ahd # AIC79xx devices
1946device amd # AMD 53C974 (Tekram DC-390(T))
1947device isp # Qlogic family
1948device ispfw # Firmware for QLogic HBAs
07ee0d26 1949device mpt # LSI '909 FC adapters
984263bc
MD
1950device ncr # NCR/Symbios Logic
1951device sym # NCR/Symbios Logic (newer chipsets)
1952device trm # Tekram DC395U/UW/F and DC315U
1953#
1954# Options for ISP
1955#
1956# ISP_TARGET_MODE - enable target mode operation
1957#options ISP_TARGET_MODE=1
1958
1959# Options used in dev/sym/ (Symbios SCSI driver).
1960#options SYM_SETUP_LP_PROBE_MAP #-Low Priority Probe Map (bits)
1961 # Allows the ncr to take precedence
1962 # 1 (1<<0) -> 810a, 860
1963 # 2 (1<<1) -> 825a, 875, 885, 895
d856dabc 1964 # 4 (1<<2) -> 895a, 896, 1510d
984263bc
MD
1965#options SYM_SETUP_SCSI_DIFF #-HVD support for 825a, 875, 885
1966 # disabled:0 (default), enabled:1
1967#options SYM_SETUP_PCI_PARITY #-PCI parity checking
1968 # disabled:0, enabled:1 (default)
1969#options SYM_SETUP_MAX_LUN #-Number of LUNs supported
1970 # default:8, range:[1..64]
1971
1972
1973# MII bus support is required for some PCI 10/100 ethernet NICs,
1974# namely those which use MII-compliant transceivers or implement
3f625015 1975# transceiver control interfaces that operate like an MII. Adding
984263bc
MD
1976# "device miibus0" to the kernel config pulls in support for
1977# the generic miibus API and all of the PHY drivers, including a
1978# generic one for PHYs that aren't specifically handled by an
1979# individual driver.
1980device miibus
1981
1982# PCI Ethernet NICs that use the common MII bus controller code.
e8e8c780 1983device ae # Attansic/Atheros L2 Fast Ethernet
da7d5358 1984device alc # Atheros AR8131/AR8132
8466ae84 1985device ale # Atheros AR8121/AR8113/AR8114
bcf4d50c 1986device age # Attansic/Atheros L1 Gigabit Ethernet
43c2aeb0 1987device bce # Broadcom NetXtreme II Gigabit Ethernet
7f186839 1988device bfe # Broadcom BCM440x 10/100 Ethernet
984263bc
MD
1989device dc # DEC/Intel 21143 and various workalikes
1990device fxp # Intel EtherExpress PRO/100B (82557, 82558)
1991device my # Myson Fast Ethernet (MTD80X, MTD89X)
1992device pcn # AMD Am79C97x PCI 10/100 NICs
44ac28ea 1993device re # RealTek 8139C+/8169
984263bc
MD
1994device rl # RealTek 8129/8139
1995device sbsh # Granch SBNI16 SHDSL modem
1996device sf # Adaptec AIC-6915 (``Starfire'')
1997device sis # Silicon Integrated Systems SiS 900/SiS 7016
1998device ste # Sundance ST201 (D-Link DFE-550TX)
1999device tl # Texas Instruments ThunderLAN
2000device tx # SMC EtherPower II (83c17x ``EPIC'')
13bca4c6 2001device vge # VIA 612x GigE
984263bc
MD
2002device vr # VIA Rhine, Rhine II
2003device wb # Winbond W89C840F
2004device xl # 3Com 3c90x (``Boomerang'', ``Cyclone'')
2005
2006# PCI Ethernet NICs.
2007device de # DEC/Intel DC21x4x (``Tulip'')
2008device txp # 3Com 3cR990 (``Typhoon'')
2009device vx # 3Com 3c590, 3c595 (``Vortex'')
2010
2011# Gigabit Ethernet NICs.
2012device bge # Broadcom BCM570x (``Tigon III'')
5330213c
SZ
2013device em # Intel Pro/1000 (8254x,8257x)
2014 # Requires ig_hal
2015device emx # Intel Pro/1000 (8257{1,2,3,4})
2016 # Requires ig_hal
9c80d176 2017device ig_hal # Intel Pro/1000 hardware abstraction layer
d217d4d9 2018device et # Agere ET1310 10/100/1000 Ethernet
984263bc 2019device lge # Level 1 LXT1001 (``Mercury'')
d47346da 2020device mxge # Myricom Myri-10G 10GbE NIC
ffb8a862 2021device nfe # nVidia nForce2/3 MCP04/51/55 CK804
984263bc 2022device nge # NatSemi DP83820 and DP83821
0db5ca13 2023device sk # SysKonnect GEnesis, LinkSys EG1023, D-Link
984263bc 2024device ti # Alteon (``Tigon I'', ``Tigon II'')
1da2c9db 2025device stge # Sundance/Tamarack TC9021 Gigabit Ethernet
2d586421 2026device msk # Marvell/SysKonnect Yukon II Gigabit Ethernet
e7a389e6 2027device jme # JMicron Gigabit/Fast Ethernet
984263bc 2028
984263bc 2029device meteor
984263bc
MD
2030
2031
2032# Brooktree driver has been ported to the new I2C framework. Thus,
2033# you'll need to have the following 3 lines in the kernel config.
2034# device smbus
2035# device iicbus
2036# device iicbb
2037# The iic and smb devices are only needed if you want to control other
2038# I2C slaves connected to the external connector of some cards.
2039#
2040device bktr
a35cc233 2041options BKTR_NEW_MSP34XX_DRIVER
984263bc 2042
e9afadfd
SW
2043# WinTV PVR-250/350 driver
2044device cxm
2045
984263bc
MD
2046#
2047# PCCARD/PCMCIA
2048#
666d2603 2049# pccard: pccard slots
6f535fd5 2050# cardbus/cbb: cardbus bridge
666d2603
JS
2051device pccard
2052device cardbus
2053device cbb
984263bc
MD
2054
2055#
2056# Laptop/Notebook options:
2057#
2058# See also:
2059# apm under `Miscellaneous hardware'
2060# above.
2061
2062# For older notebooks that signal a powerfail condition (external
2063# power supply dropped, or battery state low) by issuing an NMI:
2064
2065options POWERFAIL_NMI # make it beep instead of panicing
2066
2067#
d6644679
SW
2068# MMC/SD
2069#
2070# mmc MMC/SD bus
2071# mmcsd MMC/SD memory card
2072# sdhci Generic PCI SD Host Controller
2073#
2074device mmc
2075device mmcsd
2076device sdhci
2077
2078#
984263bc
MD
2079# SMB bus
2080#
2081# System Management Bus support is provided by the 'smbus' device.
2082# Access to the SMBus device is via the 'smb' device (/dev/smb*),
2083# which is a child of the 'smbus' device.
2084#
2085# Supported devices:
2086# smb standard io through /dev/smb*
2087#
2088# Supported SMB interfaces:
2089# iicsmb I2C to SMB bridge with any iicbus interface
2090# bktr brooktree848 I2C hardware interface
2091# intpm Intel PIIX4 (82371AB, 82443MX) Power Management Unit
2092# alpm Acer Aladdin-IV/V/Pro2 Power Management Unit
2093# ichsmb Intel ICH SMBus controller chips (82801AA, 82801AB, 82801BA)
2094# viapm VIA VT82C586B,596,686A and VT8233 SMBus controllers
2095# amdpm AMD 756 Power Management Unit
6f4e0622 2096# amdsmb AMD 8111 SMBus 2.0 Controller
984263bc
MD
2097#
2098device smbus # Bus support, required for smb below.
2099
2100device intpm
2101device alpm
2102device ichsmb
2103device viapm
2104device amdpm
6f4e0622 2105device amdsmb
984263bc
MD
2106
2107device smb
2108
2109#
2110# I2C Bus
2111#
2112# Philips i2c bus support is provided by the `iicbus' device.
2113#
2114# Supported devices:
2115# ic i2c network interface
2116# iic i2c standard io
2117# iicsmb i2c to smb bridge. Allow i2c i/o with smb commands.
2118#
2119# Supported interfaces:
2120# pcf Philips PCF8584 ISA-bus controller
2121# bktr brooktree848 I2C software interface
2122#
2123# Other:
2124# iicbb generic I2C bit-banging code (needed by lpbb, bktr)
2125#
2126device iicbus # Bus support, required for ic/iic/iicsmb below.
2127device iicbb
2128
2129device ic
2130device iic
2131device iicsmb # smb over i2c bridge
2132
2133device pcf0 at isa? port 0x320 irq 5
2134
3a514b87
HT
2135# Intel Core and newer CPUs on-die digital thermal sensor support
2136device coretemp
2137
39990074
CM
2138# AMD Family 0Fh, 10h and 11h temperature sensors
2139device kate
2140device km
2141
23e32507
CM
2142# ThinkPad Active Protection System accelerometer
2143device aps0 at isa? port 0x1600
2144
80c3f755 2145# HW monitoring devices lm(4), it(4) and nsclpcsio.
1d03db02
HT
2146device lm0 at isa? port 0x290
2147device it0 at isa? port 0x290
2148device it1 at isa? port 0xc00
2149device it2 at isa? port 0xd00
fe2da6de 2150device it3 at isa? port 0x228
80c3f755
AH
2151device nsclpcsio0 at isa? port 0x2e
2152device nsclpcsio1 at isa? port 0x4e
f81520ed
CM
2153device wbsio0 at isa? port 0x2e
2154device wbsio1 at isa? port 0x4e
2155device lm#3 at wbsio?
b7609e3d 2156device uguru0 at isa? port 0xe0 # ABIT uGuru
1d03db02 2157
984263bc
MD
2158#---------------------------------------------------------------------------
2159# ISDN4BSD
2160#
2161# See /usr/share/examples/isdn/ROADMAP for an introduction to isdn4bsd.
2162#
2163# i4b passive ISDN cards support contains the following hardware drivers:
2164#
2165# isic - Siemens/Infineon ISDN ISAC/HSCX/IPAC chipset driver
2166# iwic - Winbond W6692 PCI bus ISDN S/T interface controller
2167# ifpi - AVM Fritz!Card PCI driver
2168# ifpi2 - AVM Fritz!Card PCI driver Version 2
2169# ihfc - Cologne Chip HFC ISA/ISA-PnP chipset driver
d856dabc 2170# ifpnp - AVM Fritz!Card PnP driver
984263bc
MD
2171# itjc - Siemens ISAC / TJNet Tiger300/320 chipset
2172#
2173# i4b active ISDN cards support contains the following hardware drivers:
2174#
2175# iavc - AVM B1 PCI, AVM B1 ISA, AVM T1
2176#
2177# Note that the ``options'' (if given) and ``device'' lines must BOTH
2178# be uncommented to enable support for a given card !
2179#
2180# In addition to a hardware driver (and probably an option) the mandatory
d856dabc 2181# ISDN protocol stack devices and the mandatory support device must be
984263bc
MD
2182# enabled as well as one or more devices from the optional devices section.
2183#
2184#---------------------------------------------------------------------------
2185# isic driver (Siemens/Infineon chipsets)
2186#---------------------------------------------------------------------------
2187#
2188# ISA bus non-PnP Cards:
2189# ----------------------
2190#
2191# Teles S0/8 or Niccy 1008
2192options TEL_S0_8
2193device isic0 at isa? iomem 0xd0000 irq 5 flags 1
2194#
2195# Teles S0/16 or Creatix ISDN-S0 or Niccy 1016
2196options TEL_S0_16
2197#device isic0 at isa? port 0xd80 iomem 0xd0000 irq 5 flags 2
2198#
2199# Teles S0/16.3
2200options TEL_S0_16_3
2201#device isic0 at isa? port 0xd80 irq 5 flags 3
2202#
2203# AVM A1 or AVM Fritz!Card
2204options AVM_A1
2205#device isic0 at isa? port 0x340 irq 5 flags 4
2206#
2207# USRobotics Sportster ISDN TA intern
2208options USR_STI
2209#device isic0 at isa? port 0x268 irq 5 flags 7
2210#
2211# ITK ix1 Micro ( < V.3, non-PnP version )
2212options ITKIX1
2213#device isic0 at isa? port 0x398 irq 10 flags 18
2214#
2215# ELSA PCC-16
2216options ELSA_PCC16
2217#device isic0 at isa? port 0x360 irq 10 flags 20
2218#
2219# ISA bus PnP Cards:
2220# ------------------
2221#
2222# Teles S0/16.3 PnP
2223options TEL_S0_16_3_P
2224#device isic
2225#
2226# Creatix ISDN-S0 P&P
2227options CRTX_S0_P
2228#device isic
2229#
2230# Dr. Neuhaus Niccy Go@
2231options DRN_NGO
2232#device isic
2233#
2234# Sedlbauer Win Speed
2235options SEDLBAUER
2236#device isic
2237#
2238# Dynalink IS64PH
d856dabc 2239options DYNALINK
984263bc
MD
2240#device isic
2241#
2242# ELSA QuickStep 1000pro ISA
2243options ELSA_QS1ISA
2244#device isic
2245#
2246# ITK ix1 Micro ( V.3, PnP version )
2247options ITKIX1
2248#device isic
2249#
2250# Siemens I-Surf 2.0
2251options SIEMENS_ISURF2
2252#device isic
2253#
2254# Asuscom ISDNlink 128K ISAC
2255options ASUSCOM_IPAC
2256#device isic
2257#
2258# Eicon Diehl DIVA 2.0 and 2.02
2259options EICON_DIVA
2260#device isic
2261#
4ad6607f
SW
2262# Compaq Microcom 610
2263options COMPAQ_M610
2264#device isic
2265#
984263bc
MD
2266# PCI bus Cards:
2267# --------------
2268#
2269# ELSA MicroLink ISDN/PCI (same as ELSA QuickStep 1000pro PCI)
2270options ELSA_QS1PCI
2271#device isic
2272#
2273#---------------------------------------------------------------------------
2274# ifpnp driver for AVM Fritz!Card ISA PnP
2275#---------------------------------------------------------------------------
2276#
2277# AVM Fritz!Card ISA PnP
2278device ifpnp
2279#
2280#---------------------------------------------------------------------------
2281# ihfc driver for Cologne Chip ISA chipsets (experimental!)
2282#---------------------------------------------------------------------------
2283#
2284# Teles 16.3c ISA PnP
2285# AcerISDN P10 ISA PnP
2286# TELEINT ISDN SPEED No.1
2287device ihfc
2288#
2289#---------------------------------------------------------------------------
2290# ifpi driver for AVM Fritz!Card PCI 1.0 (2.0 unsupported!)
2291#---------------------------------------------------------------------------
2292#
2293# AVM Fritz!Card PCI 1.0
2294device ifpi
2295#
2296#---------------------------------------------------------------------------
2297# ifpi2 driver for AVM Fritz!Card PCI 2.0
2298#---------------------------------------------------------------------------
2299#
2300# AVM Fritz!Card PCI 2.0
2301device "ifpi2"
2302#
2303#---------------------------------------------------------------------------
2304# iwic driver for Winbond W6692 chipset
2305#---------------------------------------------------------------------------
2306#
2307# ASUSCOM P-IN100-ST-D (and other Winbond W6692 based cards)
2308device iwic
2309#
2310#---------------------------------------------------------------------------
3f625015 2311# itjc driver for Siemens ISAC / TJNet Tiger300/320 chipset
984263bc
MD
2312#---------------------------------------------------------------------------
2313#
2314# Traverse Technologies NETjet-S
2315# Teles PCI-TJ
2316device itjc
2317#
2318#---------------------------------------------------------------------------
2319# iavc driver (AVM active cards, needs i4bcapi driver!)
2320#---------------------------------------------------------------------------
2321#
2322pseudo-device "i4bcapi" 2
2323#
2324# AVM B1 PCI
2325device iavc0
2326#
2327# AVM B1 ISA bus (PnP mode not supported!)
2328#device iavc0 at isa? port 0x150 irq 5
2329#
2330#
2331# ISDN Protocol Stack (mandatory)
2332# -------------------------------
2333#
2334# Q.921 / layer 2 - i4b passive cards D channel handling
2335pseudo-device "i4bq921"
2336#
2337# Q.931 / layer 3 - i4b passive cards D channel handling
2338pseudo-device "i4bq931"
2339#
2340# layer 4 - i4b common passive and active card handling
2341pseudo-device "i4b"
2342#
2343# ISDN devices
2344# ------------
2345#
2346# userland driver to do ISDN tracing (for passive cards only)
2347pseudo-device "i4btrc" 4
2348#
2349# userland driver to control the whole thing (mandatory)
2350pseudo-device "i4bctl"
2351#
2352# userland driver for access to raw B channel
2353pseudo-device "i4brbch" 4
2354#
2355# userland driver for telephony
2356pseudo-device "i4btel" 2
2357#
2358# network driver for IP over raw HDLC ISDN
2359pseudo-device "i4bipr" 4
2360# enable VJ header compression detection for ipr i/f
2361options IPR_VJ
2362# enable logging of the first n IP packets to isdnd (n=32 here)
2363#options IPR_LOG=32
2364#
2365# network driver for sync PPP over ISDN - requires sppp
2366pseudo-device "i4bisppp" 4
2367
2368
2369# Parallel-Port Bus
2370#
2371# Parallel port bus support is provided by the `ppbus' device.
2372# Multiple devices may be attached to the parallel port, devices
2373# are automatically probed and attached when found.
2374#
2375# Supported devices:
2376# vpo Iomega Zip Drive
2377# Requires SCSI disk support ('scbus' and 'da'); the best
2378# performance is achieved with ports in EPP 1.9 mode.
2379# lpt Parallel Printer
2380# plip Parallel network interface
2381# ppi General-purpose I/O ("Geek Port") + IEEE1284 I/O
2382# pps Pulse per second Timing Interface
2383# lpbb Philips official parallel port I2C bit-banging interface
2384#
2385# Supported interfaces:
2386# ppc ISA-bus parallel port interfaces.
2387#
2388
2389options PPC_PROBE_CHIPSET # Enable chipset specific detection
2390 # (see flags in ppc(4))
2391options DEBUG_1284 # IEEE1284 signaling protocol debug
2392options PERIPH_1284 # Makes your computer act as a IEEE1284
2393 # compliant peripheral
2394options DONTPROBE_1284 # Avoid boot detection of PnP parallel devices
2395options VP0_DEBUG # ZIP/ZIP+ debug
2396options LPT_DEBUG # Printer driver debug
969dee2c 2397options PPC_DEBUG=2 # Parallel chipset level debug
984263bc
MD
2398options PLIP_DEBUG # Parallel network IP interface debug
2399options PCFCLOCK_VERBOSE # Verbose pcfclock driver
2400options PCFCLOCK_MAX_RETRIES=5 # Maximum read tries (default 10)
2401
2402device ppc0 at isa? irq 7
2403device ppbus
2404device vpo
2405device lpt
2406device plip
2407device ppi
2408device pps
2409device lpbb
2410device pcfclock
2411
2412# Kernel BOOTP support
2413
2414options BOOTP # Use BOOTP to obtain IP address/hostname
2415options BOOTP_NFSROOT # NFS mount root filesystem using BOOTP info
2416options BOOTP_NFSV3 # Use NFS v3 to NFS mount root
2417options BOOTP_COMPAT # Workaround for broken bootp daemons.
2418options BOOTP_WIRED_TO=fxp0 # Use interface fxp0 for BOOTP
2419
2420#
2421# Add tie-ins for a hardware watchdog. This only enable the hooks;
2422# the user must still supply the actual driver.
2423#
2424options HW_WDOG
2425
2426#
2427# Set the number of PV entries per process. Increasing this can
2428# stop panics related to heavy use of shared memory. However, that can
2429# (combined with large amounts of physical memory) cause panics at
2430# boot time due the kernel running out of VM space.
2431#
2432# If you're tweaking this, you might also want to increase the sysctls
2433# "vm.v_free_min", "vm.v_free_reserved", and "vm.v_free_target".
2434#
2435# The value below is the one more than the default.
2436#
2437options PMAP_SHPGPERPROC=201
2438
2439#
2440# Change the size of the kernel virtual address space. Due to
2441# constraints in loader(8) on i386, this must be a multiple of 4.
2442# 256 = 1 GB of kernel address space. Increasing this also causes
2443# a reduction of the address space in user processes. 512 splits
2444# the 4GB cpu address space in half (2GB user, 2GB kernel).
2445#
2446options KVA_PAGES=260
2447
2448#
2449# Disable swapping. This option removes all code which actually performs
2450# swapping, so it's not possible to turn it back on at run-time.
2451#
2452# This is sometimes usable for systems which don't have any swap space
2453# (see also sysctls "vm.defer_swapspace_pageouts" and
2454# "vm.disable_swapspace_pageouts")
2455#
2456#options NO_SWAPPING
2457
984263bc
MD
2458# Set the size of the buffer cache KVM reservation, in buffers. This is
2459# scaled by approximately 16384 bytes. The system will auto-size the buffer
2460# cache if this option is not specified.
2461#
2462options NBUF=512
2463
2464# Set the size of the mbuf KVM reservation, in clusters. This is scaled
2465# by approximately 2048 bytes. The system will auto-size the mbuf area
2466# to (512 + maxusers*16) if this option is not specified.
2467# maxusers is in turn computed at boot time depending on available memory
2468# or set to the value specified by "options MAXUSERS=x" (x=0 means
2469# autoscaling).
2470# So, to take advantage of autoscaling, you have to remove both
2471# NMBCLUSTERS and MAXUSERS (and NMBUFS) from your kernel config.
2472#
2473options NMBCLUSTERS=1024
2474
2475# Set the number of mbufs available in the system. Each mbuf
2476# consumes 256 bytes. The system will autosize this (to 4 times
2477# the number of NMBCLUSTERS, depending on other constraints)
2478# if this option is not specified.
2479#
2480options NMBUFS=4096
2481
984263bc
MD
2482# Tune the buffer cache maximum KVA reservation, in bytes. The maximum is
2483# usually capped at 200 MB, effecting machines with > 1GB of ram. Note
2484# that the buffer cache only really governs write buffering and disk block
2485# translations. The VM page cache is our primary disk cache and is not
2486# effected by the size of the buffer cache.
2487#
2488options VM_BCACHE_SIZE_MAX="(100*1024*1024)"
2489
2490# Tune the swap zone KVA reservation, in bytes. The default is typically
2491# 70 MB, giving the system the ability to manage a maximum of 28GB worth
d856dabc 2492# of swapped out data.
984263bc
MD
2493#
2494options VM_SWZONE_SIZE_MAX="(50*1024*1024)"
2495
2496#
2497# Enable extra debugging code for locks. This stores the filename and
2498# line of whatever acquired the lock in the lock itself, and change a
2499# number of function calls to pass around the relevant data. This is
2500# not at all useful unless you are debugging lock code. Also note
2501# that it is likely to break e.g. fstat(1) unless you recompile your
2502# userland with -DDEBUG_LOCKS as well.
2503#
2504options DEBUG_LOCKS
2505
2506# Set the amount of time (in seconds) the system will wait before
2507# rebooting automatically when a kernel panic occurs. If set to (-1),
2508# the system will wait indefinitely until a key is pressed on the
2509# console.
2510options PANIC_REBOOT_WAIT_TIME=16
2511
2512# Attempt to bypass the buffer cache and put data directly into the
2513# userland buffer for read operation when O_DIRECT flag is set on the
2514# file. Both offset and length of the read operation must be
d856dabc 2515# multiples of the physical media sector size.
984263bc 2516#
1ff70875 2517options DIRECTIO
984263bc
MD
2518
2519# Specify a lower limit for the number of swap I/O buffers. They are
2520# (among other things) used when bypassing the buffer cache due to
2521# DIRECTIO kernel option enabled and O_DIRECT flag set on file.
2522#
2523#options NSWBUF_MIN=120
2524
984263bc
MD
2525# The 'asr' driver provides support for current DPT/Adaptec SCSI RAID
2526# controllers (SmartRAID V and VI and later).
2527# These controllers require the CAM infrastructure.
2528#
2529device asr
2530
2531# The 'dpt' driver provides support for DPT controllers (http://www.dpt.com/).
2532# These have hardware RAID-{0,1,5} support, and do multi-initiator I/O.
2533# The DPT controllers are commonly re-licensed under other brand-names -
2534# some controllers by Olivetti, Dec, HP, AT&T, SNI, AST, Alphatronic, NEC and
2535# Compaq are actually DPT controllers.
2536#
fc29bf55 2537# See src/sys/dev/raid/dpt for debugging and other subtle options.
984263bc
MD
2538# DPT_MEASURE_PERFORMANCE Enables a set of (semi)invasive metrics. Various
2539# instruments are enabled. The tools in
2540# /usr/sbin/dpt_* assume these to be enabled.
2541# DPT_HANDLE_TIMEOUTS Normally device timeouts are handled by the DPT.
2542# If you ant the driver to handle timeouts, enable
2543# this option. If your system is very busy, this
2544# option will create more trouble than solve.
2545# DPT_TIMEOUT_FACTOR Used to compute the excessive amount of time to
2546# wait when timing out with the above option.
fc29bf55 2547# DPT_DEBUG_xxxx These are controllable from sys/dev/dpt/raid/dpt.h
984263bc
MD
2548# DPT_LOST_IRQ When enabled, will try, once per second, to catch
2549# any interrupt that got lost. Seems to help in some
2550# DPT-firmware/Motherboard combinations. Minimal
2551# cost, great benefit.
2552# DPT_RESET_HBA Make "reset" actually reset the controller
2553# instead of fudging it. Only enable this if you
2554# are 100% certain you need it.
2555
2556device dpt
2557
2558# DPT options
2559#!CAM# options DPT_MEASURE_PERFORMANCE
2560#!CAM# options DPT_HANDLE_TIMEOUTS
2561options DPT_TIMEOUT_FACTOR=4
2562options DPT_LOST_IRQ
2563options DPT_RESET_HBA
984263bc
MD
2564
2565#
2566# Compaq "CISS" RAID controllers (SmartRAID 5* series)
2567# These controllers have a SCSI-like interface, and require the
2568# CAM infrastructure.
2569#
2570device ciss
2571
2572#
2573# Intel Integrated RAID controllers.
7acc60b5
SW
2574# This driver is supported and maintained by
2575# "Leubner, Achim" <Achim_Leubner@adaptec.com>.
984263bc
MD
2576#
2577device iir
2578
2579#
2580# Mylex AcceleRAID and eXtremeRAID controllers with v6 and later
2581# firmware. These controllers have a SCSI-like interface, and require
2582# the CAM infrastructure.
2583#
2584device mly
2585
2586# USB support
2587# UHCI controller
2588device uhci
2589# OHCI controller
2590device ohci
dc1d8198
JR
2591# EHCI controller
2592device ehci
984263bc
MD
2593# General USB code (mandatory for USB)
2594device usb
2595#
89e45f2f
SW
2596# USB Bluetooth
2597device ubt
984263bc
MD
2598# Fm Radio
2599device ufm
2600# Generic USB device driver
2601device ugen
2602# Human Interface Device (anything with buttons and dials)
2603device uhid
2604# USB keyboard
2605device ukbd
2606# USB printer
2607device ulpt
2608# USB Iomega Zip 100 Drive (Requires scbus and da)
2609device umass
2610# USB modem support
2611device umodem
2612# USB mouse
2613device ums
2614# USB Rio (MP3 Player)
2615device urio
2616# USB scanners
2617device uscanner
2618# USB com devices
bfe2a61e 2619device moscom
474e48cc
HT
2620device uark
2621device ubsa
c2318dc6 2622device uchcom
984263bc 2623device ucom
474e48cc 2624device uftdi
86906a69 2625device ugensa
3ff11514 2626device umct
984263bc 2627device uplcom
5926abe5 2628device uslcom
474e48cc 2629device uticom
984263bc 2630device uvisor
474e48cc 2631device uvscom
984263bc
MD
2632
2633#
2634# ADMtek USB ethernet. Supports the LinkSys USB100TX,
2635# the Billionton USB100, the Melco LU-ATX, the D-Link DSB-650TX
2636# and the SMC 2202USB. Also works with the ADMtek AN986 Pegasus
2637# eval board.
2638device aue
2639#
204496c7
SW
2640# ASIX Electronics AX88172 USB 2.0 ethernet driver. Used in the
2641# LinkSys USB200M and various other adapters.
2642device axe
2643#
984263bc
MD
2644# CATC USB-EL1201A USB ethernet. Supports the CATC Netmate
2645# and Netmate II, and the Belkin F5U111.
2646device cue
2647#
2648# Kawasaki LSI ethernet. Supports the LinkSys USB10T,
2649# Entrega USB-NET-E45, Peracom Ethernet Adapter, the
2650# 3Com 3c19250, the ADS Technologies USB-10BT, the ATen UC10T,
2651# the Netgear EA101, the D-Link DSB-650, the SMC 2102USB
2652# and 2104USB, and the Corega USB-T.
2653device kue
3c374c15
SZ
2654#
2655# RealTek 8150 based USB ethernet device:
2656# Melco LUA-KTX
2657# GREEN HOUSE GH-USB100B
2658# Billionton ThumbLAN USBKR2-100B
2659device rue
984263bc 2660
e15de849 2661# USB wireless NICs, requires wlan_amrr
428b19ed
SZ
2662#
2663# Ralink Technology RT2501USB/RT2601USB
5c32bcdd 2664#device rum
428b19ed
SZ
2665#
2666# Ralink Technology RT2500USB
5c32bcdd 2667#device ural
428b19ed 2668
984263bc
MD
2669# debugging options for the USB subsystem
2670#
2671options USB_DEBUG
2672
2673# options for ukbd:
2674options UKBD_DFLT_KEYMAP # specify the built-in keymap
2675makeoptions UKBD_DFLT_KEYMAP=it.iso
2676
2677# Firewire support
2678device firewire # Firewire bus code
2679device sbp # SCSI over Firewire (Requires scbus and da)
2680device fwe # Ethernet over Firewire (non-standard!)
2681
ca9d2ae7
HS
2682# dcons support (Dumb Console Device)
2683device dcons # dumb console driver
2684device dcons_crom # FireWire attachment
2685options DCONS_BUF_SIZE=16384 # buffer size
2686options DCONS_POLL_HZ=100 # polling rate
2687options DCONS_FORCE_CONSOLE=1 # force to be the primary console
2688options DCONS_FORCE_GDB=1 # force to be the gdb device
2689
984263bc
MD
2690#####################################################################
2691# crypto subsystem
2692#
2693# This is a port of the openbsd crypto framework. Include this when
2694# configuring IPsec and when you have a h/w crypto device to accelerate
2695# user applications that link to openssl.
2696#
2697# Drivers are ports from openbsd with some simple enhancements that have
2698# been fed back to openbsd (and hopefully will be included).
2699
2700pseudo-device crypto # core crypto support
2701pseudo-device cryptodev # /dev/crypto for access to h/w
2702
2703device rndtest # FIPS 140-2 entropy tester
2704
2705device hifn # Hifn 7951, 7781, etc.
2706options HIFN_DEBUG # enable debugging support: hw.hifn.debug
4ad6607f 2707#options HIFN_NO_RNG # for devices without RNG
984263bc
MD
2708options HIFN_RNDTEST # enable rndtest support
2709
2710device ubsec # Broadcom 5501, 5601, 58xx
2711options UBSEC_DEBUG # enable debugging support: hw.ubsec.debug
4ad6607f 2712#options UBSEC_NO_RNG # for devices without RNG
984263bc
MD
2713options UBSEC_RNDTEST # enable rndtest support
2714
5adb7adb 2715device aesni # hardware crypto/RNG for AES-NI
80c3f755 2716device glxsb # Geode LX Security Block
661c401f 2717device padlock # hardware crypto/RNG for VIA C3/C7/Eden
80c3f755 2718
f1de7f2b
SW
2719#
2720# ACPI support using the Intel ACPI Component Architecture reference
2721# implementation.
2722#
2723# ACPI_DEBUG enables the use of the debug.acpi.level and debug.acpi.layer
2724# kernel environment variables to select initial debugging levels for the
2725# Intel ACPICA code.
2726#
2727# Note that building ACPI into the kernel is deprecated; the module is
2728# normally loaded automatically by the loader.
2729
2730device acpi
2731options ACPI_DEBUG
2732
2733# ACPI Asus Extras (LCD backlight/brightness, video output, etc.)
2734device acpi_asus
2735
2736# ACPI Fujitsu Extras (Buttons)
2737device acpi_fujitsu
2738
2739# ACPI extras driver for HP laptops
2740#device acpi_hp
2741
2742# ACPI Panasonic Extras (LCD backlight/brightness, video output, etc.)
2743device acpi_panasonic
2744
2745# ACPI Sony extra (LCD brightness)
2746device acpi_sony
2747
2748# ACPI extras driver for ThinkPad laptops
2749device acpi_thinkpad
2750
2751# ACPI Toshiba Extras (LCD backlight/brightness, video output, etc.)
2752device acpi_toshiba
2753
2754# ACPI Video Extensions (LCD backlight/brightness, video output, etc.)
2755device acpi_video
2756
ca767207 2757device aibs # ASUSTeK AI Booster (ACPI ASOC ATK0110)
3af1933a 2758device pmtimer # adjust the system clock after resume
a62a1fac 2759
984263bc 2760# DRM options:
7f3c3d6f
HT
2761# drm: General DRM code
2762# i915drm: Intel i830, i845, i915, i945, i965, G33/35
2763# mach64drm: ATI Mach64 cards - Rage and 3D Rage series
2764# mgadrm: AGP Matrox G200, G400, G450, G550
2765# r128drm: ATI Rage 128 cards
2766# radeondrm: ATI Radeon cards
2767# savagedrm: Savage cards
2768# sisdrm: Sis cards
2769# tdfxdrm: 3dfx Voodoo 3/4/5 and Banshee
2770#
2771# DRM_DEBUG: include debug printfs, very slow
2772#
2773# DRM requires AGP in the kernel.
2774
2775device drm
2776device "i915drm"
2777device "mach64drm"
984263bc
MD
2778device mgadrm
2779device "r128drm"
2780device radeondrm
7f3c3d6f
HT
2781device savagedrm
2782device sisdrm
984263bc
MD
2783device tdfxdrm
2784
2785options DRM_DEBUG
4ad6607f 2786options DRM_LINUX
984263bc
MD
2787
2788#
c4bf625e
HT
2789# Misc devices
2790#
2791device cmx # Omnikey CardMan 4040 smartcard reader
80c3f755 2792device gpio # Enable support for the gpio framework
c4bf625e
HT
2793
2794#
984263bc
MD
2795# Embedded system options:
2796#
2797# An embedded system might want to run something other than init.
22628b14 2798options INIT_PATH="/sbin/init:/sbin/oinit"
984263bc
MD
2799
2800# Debug options
2801options BUS_DEBUG # enable newbus debugging
984263bc 2802options NPX_DEBUG # enable npx debugging (FPU/math emu)
8f2c9819 2803options RSS_DEBUG # enable RSS (Receive Side Scaling) debugging
984263bc 2804
8a4ec68a
SW
2805# Record the program counter of the code interrupted by the statistics
2806# clock interrupt. Use pctrack(8) to dump this information.
2807options DEBUG_PCTRACK
2808
984263bc
MD
2809# More undocumented options for linting.
2810# Note that documenting these are not considered an affront.
2811
4ad6607f 2812#options ACPI_NO_SEMAPHORES
984263bc 2813options AHC_DUMP_EEPROM
4ad6607f 2814#options BKTR_ALLOC_PAGES=xxx
984263bc
MD
2815options CAM_DEBUG_DELAY
2816options CLUSTERDEBUG
2817options COMPAT_LINUX
4ad6607f 2818options COMPAT_SUNOS
984263bc 2819options DEBUG
4ad6607f
SW
2820options DEBUG_CRIT_SECTIONS
2821options DEBUG_INTERRUPTS
984263bc 2822#options DISABLE_PSE
43c2aeb0
SZ
2823options BCE_DEBUG
2824options BCE_NVRAM_WRITE_SUPPORT
e6cde6e6 2825options EMX_RSS_DEBUG
93bfe1b8 2826options JME_RSS_DEBUG
4ad6607f 2827#options ED_NO_MIIBUS
984263bc 2828options ENABLE_ALART
969dee2c 2829options FB_DEBUG=2
984263bc
MD
2830options FB_INSTALL_CDEV
2831options FE_8BIT_SUPPORT
2832options I4B_SMP_WORKAROUND
2833options I586_PMC_GUPROF=0x70000
98091aa8
SW
2834#options IEEE80211_DEBUG_REFCNT
2835options IEEE80211_SUPPORT_SUPERG
969dee2c 2836options KBDIO_DEBUG=10
984263bc
MD
2837options KBD_MAXRETRY=4
2838options KBD_MAXWAIT=6
2839options KBD_RESETDELAY=201
4ad6607f 2840options KERN_TIMESTAMP
984263bc 2841options KEY
4ad6607f 2842options LINPROCFS
984263bc
MD
2843options LOCKF_DEBUG
2844options LOUTB
4ad6607f 2845#options MAXFILES=xxx
5054c0b0 2846options MBUF_DEBUG
4ad6607f 2847options METEOR_TEST_VIDEO
984263bc 2848options NETATALKDEBUG
4ad6607f 2849options PANIC_DEBUG
969dee2c 2850options PSM_DEBUG=4
984263bc
MD
2851options SCSI_NCR_DEBUG
2852options SCSI_NCR_MAX_SYNC=10000
2853options SCSI_NCR_MAX_WIDE=1
2854options SCSI_NCR_MYADDR=7
984263bc
MD
2855options SHOW_BUSYBUFS # List buffers that prevent root unmount
2856options SIMPLELOCK_DEBUG
2857options SI_DEBUG
2858options SLIP_IFF_OPTS
4ad6607f 2859options SOCKBUF_DEBUG
98091aa8
SW
2860options TDMA_BINTVAL_DEFAULT=5
2861options TDMA_SLOTCNT_DEFAULT=2
2862options TDMA_SLOTLEN_DEFAULT=10*1000
2863options TDMA_TXRATE_11A_DEFAULT=2*24
2864options TDMA_TXRATE_11B_DEFAULT=2*11
2865options TDMA_TXRATE_11G_DEFAULT=2*24
2866options TDMA_TXRATE_11NA_DEFAULT="(4|IEEE80211_RATE_MCS)"
2867options TDMA_TXRATE_11NG_DEFAULT="(4|IEEE80211_RATE_MCS)"
2868options TDMA_TXRATE_HALF_DEFAULT=2*12
2869options TDMA_TXRATE_QUARTER_DEFAULT=2*6
2870options TDMA_TXRATE_TURBO_DEFAULT=2*24
984263bc
MD
2871options TIMER_FREQ="((14318182+6)/12)"
2872options VFS_BIO_DEBUG
2873options XBONEHACK
81540c2d
EN
2874
2875options KTR
d9f18464 2876#options KTR_CTXSW
f3e0b5f0 2877#options KTR_ETHERNET
edba61da 2878#options KTR_GIANT_CONTENTION
f3e0b5f0 2879#options KTR_HAMMER
c112b277
SW
2880#options KTR_IF_BGE
2881#options KTR_IF_EM
5330213c 2882#options KTR_IF_EMX
9db4b353
SZ
2883#options KTR_IF_START
2884#options KTR_IFQ
4ad6607f 2885#options KTR_IPIQ
d0377f9b 2886#options KTR_KERNENTRY
4ad6607f 2887#options KTR_MEMORY
d16c94f7 2888#options KTR_POLLING
d0377f9b 2889#options KTR_SERIALIZER
c112b277
SW
2890#options KTR_SPIN_CONTENTION
2891#options KTR_TESTLOG
4ad6607f
SW
2892#options KTR_TOKENS
2893#options KTR_USB_MEMORY
d3776285 2894options KTR_ALL
81540c2d
EN
2895options KTR_ENTRIES=1024
2896options KTR_VERBOSE=1
4d723e5a
JS
2897
2898# ALTQ
2899options ALTQ #alternate queueing
2900options ALTQ_CBQ #class based queueing
2901options ALTQ_RED #random early detection
2902options ALTQ_RIO #triple red for diffserv (needs RED)
2903options ALTQ_HFSC #hierarchical fair service curve
2904options ALTQ_PRIQ #priority queue
5950bf01 2905options ALTQ_FAIRQ #fair queue
4d723e5a
JS
2906#options ALTQ_NOPCC #don't use processor cycle counter
2907options ALTQ_DEBUG #for debugging
2908# you might want to set kernel timer to 1kHz if you use CBQ,
2909# especially with 100baseT
2910#options HZ=1000
5e937ff0
EN
2911
2912# SCTP
2913options SCTP
d856dabc 2914options SCTP_DEBUG
5e937ff0
EN
2915options SCTP_USE_ADLER32
2916options SCTP_HIGH_SPEED
2917options SCTP_STAT_LOGGING
2918options SCTP_CWND_LOGGING
2919options SCTP_BLK_LOGGING
2920options SCTP_STR_LOGGING
2921options SCTP_FR_LOGGING
2922options SCTP_MAP_LOGGING
21fa6062 2923
e4734395
SW
2924# DSCHED stuff
2925options DSCHED_FQ
2926
80c3f755
AH
2927# WATCHDOG
2928options WATCHDOG_ENABLE # Enable watchdog support framework
2929options WDOG_DISABLE_ON_PANIC # Automatically disable watchdogs on panic
2930
2931# LED
0210859c 2932options ERROR_LED_ON_PANIC # If an error led is present, light it up on panic