Remove i386 support.
[dragonfly.git] / sys / config / LINT
CommitLineData
984263bc
MD
1#
2# LINT -- config file for checking all the sources, tries to pull in
3# as much of the source tree as it can.
4#
5# $FreeBSD: src/sys/i386/conf/LINT,v 1.749.2.144 2003/06/04 17:56:59 sam Exp $
4db955e1 6# $DragonFly: src/sys/config/LINT,v 1.139 2007/11/07 17:42:50 dillon Exp $
984263bc
MD
7#
8# NB: You probably don't want to try running a kernel built from this
9# file. Instead, you should start from GENERIC, and add options from
10# this file as required.
11#
12
a9295349
MD
13# These directives are mandatory. The machine directive specifies the
14# platform and the machine_arch directive specifies the cpu architecture.
984263bc 15#
0955fd91
MD
16platform pc32
17machine i386
a9295349 18machine_arch i386
984263bc
MD
19
20#
21# This is the ``identification'' of the kernel. Usually this should
22# be the same as the name of your kernel.
23#
24ident LINT
25
26#
27# The `maxusers' parameter controls the static sizing of a number of
28# internal system tables by a formula defined in subr_param.c. Setting
29# maxusers to 0 will cause the system to auto-size based on physical
30# memory.
31#
32maxusers 10
33
34#
35# The `makeoptions' parameter allows variables to be passed to the
36# generated Makefile in the build area.
37#
38# CONF_CFLAGS gives some extra compiler flags that are added to ${CFLAGS}
39# after most other flags. Here we use it to inhibit use of non-optimal
40# gcc builtin functions (e.g., memcmp).
41#
42# DEBUG happens to be magic.
43# The following is equivalent to 'config -g KERNELNAME' and creates
44# 'kernel.debug' compiled with -g debugging as well as a normal
45# 'kernel'. Use 'make install.debug' to install the debug kernel
46# but that isn't normally necessary as the debug symbols are not loaded
47# by the kernel and are not useful there anyway.
48#
49# KERNEL can be overridden so that you can change the default name of your
50# kernel.
51#
52# MODULES_OVERRIDE can be used to limit modules built to a specific list.
53#
c2c83759
MD
54# INSTALLSTRIPPED can be set to cause installkernel to install stripped
55# kernels and modules rather than a kernel and modules with debug symbols.
56#
57# INSTALLSTRIPPEDMODULES can be set to allow a full debug kernel to be
58# installed, but to strip the installed modules.
59#
984263bc
MD
60makeoptions CONF_CFLAGS=-fno-builtin #Don't allow use of memcmp, etc.
61#makeoptions DEBUG=-g #Build kernel with gdb(1) debug symbols
62#makeoptions KERNEL=foo #Build kernel "foo" and install "/foo"
63# Only build Linux API modules and plus those parts of the sound system I need.
64#makeoptions MODULES_OVERRIDE="linux sound/snd sound/pcm sound/driver/maestro3"
c2c83759
MD
65#makeoptions INSTALLSTRIPPED=1
66#makeoptions INSTALLSTRIPPEDMODULES=1
984263bc
MD
67
68#
69# Certain applications can grow to be larger than the 128M limit
70# that FreeBSD initially imposes. Below are some options to
71# allow that limit to grow to 256MB, and can be increased further
72# with changing the parameters. MAXDSIZ is the maximum that the
73# limit can be set to, and the DFLDSIZ is the default value for
74# the limit. MAXSSIZ is the maximum that the stack limit can be
75# set to. You might want to set the default lower than the max,
76# and explicitly set the maximum with a shell command for processes
77# that regularly exceed the limit like INND.
78#
79options MAXDSIZ="(256*1024*1024)"
80options MAXSSIZ="(256*1024*1024)"
81options DFLDSIZ="(256*1024*1024)"
82
83#
84# BLKDEV_IOSIZE sets the default block size used in user block
56be8454 85# device I/O. Note that this value will be overridden by the label
984263bc
MD
86# when specifying a block device from a label with a non-0
87# partition blocksize. The default is PAGE_SIZE.
88#
89options BLKDEV_IOSIZE=8192
90
91# Options for the VM subsystem.
92options PQ_CACHESIZE=512 # color for 512k/16k cache
984263bc
MD
93
94# This allows you to actually store this configuration file into
95# the kernel binary itself, where it may be later read by saying:
96# strings -n 3 /kernel | sed -n 's/^___//p' > MYKERNEL
97#
98options INCLUDE_CONFIG_FILE # Include this file in kernel
99
100#
101# The root device and filesystem type can be compiled in;
102# this provides a fallback option if the root device cannot
103# be correctly guessed by the bootstrap code, or an override if
104# the RB_DFLTROOT flag (-r) is specified when booting the kernel.
105#
106options ROOTDEVNAME=\"ufs:da0s2e\"
107
108\f
109#####################################################################
110# SMP OPTIONS:
111#
112# SMP enables building of a Symmetric MultiProcessor Kernel.
113# APIC_IO enables the use of the IO APIC for Symmetric I/O.
114#
115# Notes:
116#
117# An SMP kernel will ONLY run on an Intel MP spec. qualified motherboard.
118#
4db955e1 119# Be sure to disable 'cpu I486_CPU' for SMP kernels.
984263bc
MD
120#
121# Check the 'Rogue SMP hardware' section to see if additional options
122# are required by your hardware.
123#
124
125# Mandatory:
126options SMP # Symmetric MultiProcessor Kernel
127options APIC_IO # Symmetric (APIC) I/O
984263bc
MD
128
129#
130# Rogue SMP hardware:
131#
132
133# Bridged PCI cards:
134#
135# The MP tables of most of the current generation MP motherboards
136# do NOT properly support bridged PCI cards. To use one of these
137# cards you should refer to ???
138
139\f
140#####################################################################
141# CPU OPTIONS
142
143#
144# You must specify at least one CPU (the one you intend to run on);
145# deleting the specification for CPUs you don't need to use may make
4db955e1 146# parts of the system run faster.
984263bc 147#
984263bc
MD
148cpu I486_CPU
149cpu I586_CPU # aka Pentium(tm)
150cpu I686_CPU # aka Pentium Pro(tm)
151
152#
153# Options for CPU features.
154#
53c1a7a7
MD
155# CPU_AMD64X2_INTR_SPAM tries to route HyperTransport EXTINT and NMI
156# messages to LINT0 on the local APIC when the BIOS has forgotten to
157# do that. If this is not done on a multi-core cpu, EXTINT and NMI
3f5e28f4 158# get routed to the INTR/NMI pins on *BOTH* cores simultaneously, causing
53c1a7a7
MD
159# two INTA ack cycles one of which will almost certainly result in a
160# spurious interrupt vector being presented. This is often visible as
161# an unmaskable IRQ 7 which occurs for every normal interrupt that occurs
162# on a system.
163#
984263bc
MD
164# CPU_ATHLON_SSE_HACK tries to enable SSE instructions when the BIOS has
165# forgotten to enable them.
166#
167# CPU_BLUELIGHTNING_FPU_OP_CACHE enables FPU operand cache on IBM
168# BlueLightning CPU. It works only with Cyrix FPU, and this option
169# should not be used with Intel FPU.
170#
171# CPU_BLUELIGHTNING_3X enables triple-clock mode on IBM Blue Lightning
172# CPU if CPU supports it. The default is double-clock mode on
173# BlueLightning CPU box.
174#
175# CPU_BTB_EN enables branch target buffer on Cyrix 5x86 (NOTE 1).
176#
177# CPU_DIRECT_MAPPED_CACHE sets L1 cache of Cyrix 486DLC CPU in direct
178# mapped mode. Default is 2-way set associative mode.
179#
180# CPU_CYRIX_NO_LOCK enables weak locking for the entire address space
181# of Cyrix 6x86 and 6x86MX CPUs by setting the NO_LOCK bit of CCR1.
182# Otherwise, the NO_LOCK bit of CCR1 is cleared. (NOTE 3)
183#
184# CPU_DISABLE_5X86_LSSER disables load store serialize (i.e. enables
185# reorder). This option should not be used if you use memory mapped
186# I/O device(s).
187#
642a6e88 188# CPU_DISABLE_SSE disables SSE/MMX2 instructions support.
984263bc 189#
18a582c9
JR
190# CPU_ENABLE_TCC enables Thermal Control Circuitry (TCC) found in some
191# Pentium(tm) 4 and (possibly) later CPUs. When enabled and detected,
192# TCC supports restricting power consumption using the hw.p4tcc.*
193# sysctls. This operates independently of SpeedStep and is useful on
194# systems where other mechanisms such as apm(4) or acpi(4) don't work.
195#
5d327b77
YT
196# CPU_ENABLE_EST enables support for Enhanced SpeedStep technology
197# found in Pentium(tm) M processors.
198#
984263bc
MD
199# CPU_FASTER_5X86_FPU enables faster FPU exception handler.
200#
201# CPU_I486_ON_386 enables CPU cache on i486 based CPU upgrade products
202# for i386 machines.
203#
204# CPU_IORT defines I/O clock delay time (NOTE 1). Default values of
205# I/O clock delay time on Cyrix 5x86 and 6x86 are 0 and 7,respectively
206# (no clock delay).
207#
3f5e28f4 208# CPU_L2_LATENCY specified the L2 cache latency value. This option is used
984263bc
MD
209# only when CPU_PPRO2CELERON is defined and Mendocino Celeron is detected.
210# The default value is 5.
211#
212# CPU_ELAN enables support for AMDs ElanSC520 CPU.
213#
214# CPU_LOOP_EN prevents flushing the prefetch buffer if the destination
215# of a jump is already present in the prefetch buffer on Cyrix 5x86(NOTE
216# 1).
217#
218# CPU_PPRO2CELERON enables L2 cache of Mendocino Celeron CPUs. This option
219# is useful when you use Socket 8 to Socket 370 converter, because most Pentium
220# Pro BIOSs do not enable L2 cache of Mendocino Celeron CPUs.
221#
222# CPU_RSTK_EN enables return stack on Cyrix 5x86 (NOTE 1).
223#
224# CPU_SUSP_HLT enables suspend on HALT. If this option is set, CPU
225# enters suspend mode following execution of HALT instruction.
226#
227# CPU_WT_ALLOC enables write allocation on Cyrix 6x86/6x86MX and AMD
228# K5/K6/K6-2 cpus.
229#
230# CYRIX_CACHE_WORKS enables CPU cache on Cyrix 486 CPUs with cache
231# flush at hold state.
232#
233# CYRIX_CACHE_REALLY_WORKS enables (1) CPU cache on Cyrix 486 CPUs
234# without cache flush at hold state, and (2) write-back CPU cache on
235# Cyrix 6x86 whose revision < 2.7 (NOTE 2).
236#
237# NO_F00F_HACK disables the hack that prevents Pentiums (and ONLY
238# Pentiums) from locking up when a LOCK CMPXCHG8B instruction is
239# executed. This option is only needed if I586_CPU is also defined,
240# and should be included for any non-Pentium CPU that defines it.
241#
242# NO_MEMORY_HOLE is an optimisation for systems with AMD K6 processors
243# which indicates that the 15-16MB range is *definitely* not being
244# occupied by an ISA memory hole.
245#
246# NOTE 1: The options, CPU_BTB_EN, CPU_LOOP_EN, CPU_IORT,
247# CPU_LOOP_EN and CPU_RSTK_EN should not be used because of CPU bugs.
248# These options may crash your system.
249#
250# NOTE 2: If CYRIX_CACHE_REALLY_WORKS is not set, CPU cache is enabled
251# in write-through mode when revision < 2.7. If revision of Cyrix
252# 6x86 >= 2.7, CPU cache is always enabled in write-back mode.
253#
254# NOTE 3: This option may cause failures for software that requires
255# locked cycles in order to operate correctly.
256#
e71347e9 257options CPU_AMD64X2_INTR_SPAM
984263bc
MD
258options CPU_ATHLON_SSE_HACK
259options CPU_BLUELIGHTNING_FPU_OP_CACHE
260options CPU_BLUELIGHTNING_3X
261options CPU_BTB_EN
e71347e9 262options CPU_CYRIX_NO_LOCK
984263bc
MD
263options CPU_DIRECT_MAPPED_CACHE
264options CPU_DISABLE_5X86_LSSER
e71347e9 265options CPU_DISABLE_SSE
984263bc 266options CPU_ELAN
5d327b77 267options CPU_ENABLE_EST
18a582c9 268options CPU_ENABLE_TCC
984263bc
MD
269options CPU_FASTER_5X86_FPU
270options CPU_I486_ON_386
271options CPU_IORT
272options CPU_L2_LATENCY=5
273options CPU_LOOP_EN
274options CPU_PPRO2CELERON
275options CPU_RSTK_EN
276options CPU_SUSP_HLT
277options CPU_WT_ALLOC
278options CYRIX_CACHE_WORKS
279options CYRIX_CACHE_REALLY_WORKS
280#options NO_F00F_HACK
e71347e9 281options NO_MEMORY_HOLE
984263bc
MD
282
283#
284# A math emulator is mandatory if you wish to run on hardware which
6f535fd5 285# does not have a floating-point processor.
984263bc 286options MATH_EMULATE #Support for x87 emulation
984263bc
MD
287\f
288#####################################################################
289# COMPATIBILITY OPTIONS
290
291#
292# Implement system calls compatible with 4.3BSD and older versions of
293# FreeBSD. You probably do NOT want to remove this as much current code
294# still relies on the 4.3 emulation.
295#
296options COMPAT_43
297
db37e804
JS
298#
299# Implement system calls compatible with DragonFly 1.2 and older.
300#
301options COMPAT_DF12 #Compatible with DragonFly 1.2 and earlier
302
984263bc
MD
303#
304# These three options provide support for System V Interface
305# Definition-style interprocess communication, in the form of shared
306# memory, semaphores, and message queues, respectively.
307#
308# System V shared memory and tunable parameters
309options SYSVSHM # include support for shared memory
310options SHMMAXPGS=1025 # max amount of shared memory pages (4k on i386)
311options SHMALL=1025 # max amount of shared memory (bytes)
312options SHMMAX="(SHMMAXPGS*PAGE_SIZE+1)"
313 # max shared memory segment size (bytes)
314options SHMMIN=2 # min shared memory segment size (bytes)
315options SHMMNI=33 # max number of shared memory identifiers
316options SHMSEG=9 # max shared memory segments per process
317
318# System V semaphores and tunable parameters
319options SYSVSEM # include support for semaphores
320options SEMMAP=31 # amount of entries in semaphore map
321options SEMMNI=11 # number of semaphore identifiers in the system
322options SEMMNS=61 # number of semaphores in the system
323options SEMMNU=31 # number of undo structures in the system
324options SEMMSL=61 # max number of semaphores per id
325options SEMOPM=101 # max number of operations per semop call
326options SEMUME=11 # max number of undo entries per process
327
328# System V message queues and tunable parameters
329options SYSVMSG # include support for message queues
330options MSGMNB=2049 # max characters per message queue
331options MSGMNI=41 # max number of message queue identifiers
332options MSGSEG=2049 # max number of message segments in the system
333options MSGSSZ=16 # size of a message segment MUST be power of 2
334options MSGTQL=41 # max amount of messages in the system
335
336\f
337#####################################################################
338# DEBUGGING OPTIONS
339
340#
341# Enable the kernel debugger.
342#
343options DDB
344
4ad6607f
SW
345#
346# Print a stack trace on kernel panic.
347#
348options DDB_TRACE
349
984263bc
MD
350#
351# Don't drop into DDB for a panic. Intended for unattended operation
352# where you may want to drop to DDB from the console, but still want
353# the machine to recover from a panic
354#
355options DDB_UNATTENDED
356
357#
358# If using GDB remote mode to debug the kernel, there's a non-standard
359# extension to the remote protocol that can be used to use the serial
360# port as both the debugging port and the system console. It's non-
361# standard and you're on your own if you enable it. See also the
362# "remotechat" variables in the FreeBSD specific version of gdb.
363#
364options GDB_REMOTE_CHAT
365
366#
367# KTRACE enables the system-call tracing facility ktrace(2).
368#
369options KTRACE #kernel tracing
370
371#
372# The INVARIANTS option is used in a number of source files to enable
373# extra sanity checking of internal structures. This support is not
374# enabled by default because of the extra time it would take to check
375# for these conditions, which can only occur as a result of
376# programming errors.
377#
378options INVARIANTS
379
984263bc
MD
380#
381# The DIAGNOSTIC option is used to enable extra debugging information
382# from some parts of the kernel. As this makes everything more noisy,
383# it is disabled by default.
384#
385options DIAGNOSTIC
386
387#
388# PERFMON causes the driver for Pentium/Pentium Pro performance counters
389# to be compiled. See perfmon(4) for more information.
390#
391options PERFMON
392
393
394#
395# This option let some drivers co-exist that can't co-exist in a running
396# system. This is used to be able to compile all kernel code in one go for
397# quality assurance purposes (like this file, which the option takes it name
398# from.)
399#
400options COMPILING_LINT
401
402
403# XXX - this doesn't belong here.
404# Allow ordinary users to take the console - this is useful for X.
405options UCONSOLE
406
407# XXX - this doesn't belong here either
408options USERCONFIG #boot -c editor
409options INTRO_USERCONFIG #imply -c and show intro screen
410options VISUAL_USERCONFIG #visual boot -c editor
411
412\f
413#####################################################################
414# NETWORKING OPTIONS
415
416#
417# Protocol families:
418# Only the INET (Internet) family is officially supported in FreeBSD.
419# Source code for the NS (Xerox Network Service) is provided for amusement
420# value.
421#
422options INET #Internet communications protocols
423options INET6 #IPv6 communications protocols
424options IPSEC #IP security
425options IPSEC_ESP #IP security (crypto; define w/ IPSEC)
426options IPSEC_DEBUG #debug for IP security
427#
428# Set IPSEC_FILTERGIF to force packets coming through a gif tunnel
429# to be processed by any configured packet filtering (ipfw, ipf).
430# The default is that packets coming from a tunnel are _not_ processed;
431# they are assumed trusted.
432#
433# Note that enabling this can be problematic as there are no mechanisms
434# in place for distinguishing packets coming out of a tunnel (e.g. no
435# encX devices as found on openbsd).
436#
437#options IPSEC_FILTERGIF #filter ipsec packets from a tunnel
438
439#
440# Experimental IPsec implementation that uses the kernel crypto
441# framework. This cannot be configured together with IPSEC and
442# (currently) supports only IPv4. To use this you must also
443# configure the crypto device (see below). Note that with this
444# you get all the IPsec protocols (e.g. there is no FAST_IPSEC_ESP).
445# IPSEC_DEBUG is used, as above, to configure debugging support
446# within the IPsec protocols.
447#
448#options FAST_IPSEC #new IPsec
449
450options IPX #IPX/SPX communications protocols
451options IPXIP #IPX in IP encapsulation (not available)
452options IPTUNNEL #IP in IPX encapsulation (not available)
453
454options NCP #NetWare Core protocol
455
456options NETATALK #Appletalk communications protocols
457
458# These are currently broken but are shipped due to interest.
459#options NS #Xerox NS protocols
460#options NSIP #XNS over IP
461
462#
463# SMB/CIFS requester
464# NETSMB enables support for SMB protocol, it requires LIBMCHAIN and LIBICONV
465# options.
466# NETSMBCRYPTO enables support for encrypted passwords.
467options NETSMB #SMB/CIFS requester
468options NETSMBCRYPTO #encrypted password support for SMB
469
470# mchain library. It can be either loaded as KLD or compiled into kernel
471options LIBMCHAIN #mbuf management library
472
473# netgraph(4). Enable the base netgraph code with the NETGRAPH option.
474# Individual node types can be enabled with the corresponding option
475# listed below; however, this is not strictly necessary as netgraph
476# will automatically load the corresponding KLD module if the node type
477# is not already compiled into the kernel. Each type below has a
4ad6607f 478# corresponding man page, e.g., ng_async(4).
984263bc
MD
479options NETGRAPH #netgraph(4) system
480options NETGRAPH_ASYNC
481options NETGRAPH_BPF
4ad6607f 482options NETGRAPH_BRIDGE
984263bc
MD
483options NETGRAPH_CISCO
484options NETGRAPH_ECHO
7dab44e5 485options NETGRAPH_EIFACE
984263bc
MD
486options NETGRAPH_ETHER
487options NETGRAPH_FRAME_RELAY
488options NETGRAPH_HOLE
489options NETGRAPH_IFACE
490options NETGRAPH_KSOCKET
491options NETGRAPH_L2TP
492options NETGRAPH_LMI
493# MPPC compression requires proprietary files (not included)
494#options NETGRAPH_MPPC_COMPRESSION
495options NETGRAPH_MPPC_ENCRYPTION
496options NETGRAPH_ONE2MANY
497options NETGRAPH_PPP
498options NETGRAPH_PPPOE
499options NETGRAPH_PPTPGRE
500options NETGRAPH_RFC1490
501options NETGRAPH_SOCKET
502options NETGRAPH_TEE
503options NETGRAPH_TTY
504options NETGRAPH_UI
505options NETGRAPH_VJC
506
507device mn # Munich32x/Falc54 Nx64kbit/sec cards.
508
509#
510# Network interfaces:
511# The `loop' pseudo-device is MANDATORY when networking is enabled.
512# The `ether' pseudo-device provides generic code to handle
513# Ethernets; it is MANDATORY when a Ethernet device driver is
b15531e9 514# configured.
984263bc
MD
515# The `sppp' pseudo-device serves a similar role for certain types
516# of synchronous PPP links (like `cx', `ar').
517# The `sl' pseudo-device implements the Serial Line IP (SLIP) service.
518# The `ppp' pseudo-device implements the Point-to-Point Protocol.
519# The `bpf' pseudo-device enables the Berkeley Packet Filter. Be
520# aware of the legal and administrative consequences of enabling this
521# option. The number of devices determines the maximum number of
522# simultaneous BPF clients programs runnable.
523# The `disc' pseudo-device implements a minimal network interface,
524# which throws away all packets sent and never receives any. It is
525# included for testing purposes. This shows up as the 'ds' interface.
526# The `tun' pseudo-device implements (user-)ppp and nos-tun
527# The `gif' pseudo-device implements IPv6 over IP4 tunneling,
528# IPv4 over IPv6 tunneling, IPv4 over IPv4 tunneling and
529# IPv6 over IPv6 tunneling.
530# The `gre' device implements two types of IP4 over IP4 tunneling:
531# GRE and MOBILE, as specified in the RFC1701 and RFC2004.
532# The `faith' pseudo-device captures packets sent to it and diverts them
533# to the IPv4/IPv6 translation daemon.
534# The `stf' device implements 6to4 encapsulation.
535# The `ef' pseudo-device provides support for multiple ethernet frame types
536# specified via ETHER_* options. See ef(4) for details.
537#
538# The PPP_BSDCOMP option enables support for compress(1) style entire
539# packet compression, the PPP_DEFLATE is for zlib/gzip style compression.
540# PPP_FILTER enables code for filtering the ppp data stream and selecting
541# events for resetting the demand dial activity timer - requires bpf.
542# See pppd(8) for more details.
543#
544pseudo-device ether #Generic Ethernet
545pseudo-device vlan 1 #VLAN support
db37145f 546pseudo-device bridge #Bridging support
984263bc
MD
547pseudo-device sppp #Generic Synchronous PPP
548pseudo-device loop #Network loopback device
549pseudo-device bpf #Berkeley packet filter
550pseudo-device disc #Discard device (ds0, ds1, etc)
551pseudo-device tun #Tunnel driver (ppp(8), nos-tun(8))
552pseudo-device sl 2 #Serial Line IP
553pseudo-device gre #IP over IP tunneling
554pseudo-device ppp 2 #Point-to-point protocol
555options PPP_BSDCOMP #PPP BSD-compress support
556options PPP_DEFLATE #PPP zlib/deflate/gzip support
557options PPP_FILTER #enable bpf filtering (needs bpf)
558
559pseudo-device ef # Multiple ethernet frames support
560options ETHER_II # enable Ethernet_II frame
561options ETHER_8023 # enable Ethernet_802.3 (Novell) frame
562options ETHER_8022 # enable Ethernet_802.2 frame
563options ETHER_SNAP # enable Ethernet_802.2/SNAP frame
564
565# for IPv6
566pseudo-device gif #IPv6 and IPv4 tunneling
567pseudo-device faith 1 #for IPv6 and IPv4 translation
568pseudo-device stf #6to4 IPv6 over IPv4 encapsulation
569
570#
571# Internet family options:
572#
573# MROUTING enables the kernel multicast packet forwarder, which works
574# with mrouted(8).
575#
f1f552f6
JH
576# PIM enables Protocol Independent Multicast in the kernel.
577# Requires MROUTING enabled.
578#
984263bc
MD
579# IPFIREWALL enables support for IP firewall construction, in
580# conjunction with the `ipfw' program. IPFIREWALL_VERBOSE sends
581# logged packets to the system logger. IPFIREWALL_VERBOSE_LIMIT
582# limits the number of times a matching entry can be logged.
583#
584# WARNING: IPFIREWALL defaults to a policy of "deny ip from any to any"
585# and if you do not add other rules during startup to allow access,
586# YOU WILL LOCK YOURSELF OUT. It is suggested that you set firewall_type=open
587# in /etc/rc.conf when first enabling this feature, then refining the
588# firewall rules in /etc/rc.firewall after you've tested that the new kernel
589# feature works properly.
590#
591# IPFIREWALL_DEFAULT_TO_ACCEPT causes the default rule (at boot) to
592# allow everything. Use with care, if a cracker can crash your
593# firewall machine, they can get to your protected machines. However,
594# if you are using it as an as-needed filter for specific problems as
595# they arise, then this may be for you. Changing the default to 'allow'
596# means that you won't get stuck if the kernel and /sbin/ipfw binary get
597# out of sync.
598#
599# IPDIVERT enables the divert IP sockets, used by ``ipfw divert''
600#
601# IPSTEALTH enables code to support stealth forwarding (i.e., forwarding
602# packets without touching the ttl). This can be useful to hide firewalls
603# from traceroute and similar tools.
604#
605# TCPDEBUG is undocumented.
606#
607options MROUTING # Multicast routing
f1f552f6 608options PIM # Protocol Independent Multicast
984263bc
MD
609options IPFIREWALL #firewall
610options IPFIREWALL_VERBOSE #enable logging to syslogd(8)
611options IPFIREWALL_FORWARD #enable transparent proxy support
612options IPFIREWALL_VERBOSE_LIMIT=100 #limit verbosity
613options IPFIREWALL_DEFAULT_TO_ACCEPT #allow everything by default
614options IPV6FIREWALL #firewall for IPv6
615options IPV6FIREWALL_VERBOSE
616options IPV6FIREWALL_VERBOSE_LIMIT=100
617options IPV6FIREWALL_DEFAULT_TO_ACCEPT
618options IPDIVERT #divert sockets
619options IPFILTER #ipfilter support
620options IPFILTER_LOG #ipfilter logging
621options IPFILTER_DEFAULT_BLOCK #block all packets by default
622options IPSTEALTH #support for stealth forwarding
623options TCPDEBUG
c1d552d0 624options NS # NETNS support
984263bc 625
02742ec6
JS
626device pf
627device pfsync
628device pflog
629
0d16ba1d
MD
630#CARP
631pseudo-device carp
632options CARP
633
984263bc
MD
634# The MBUF_STRESS_TEST option enables options which create
635# various random failures / extreme cases related to mbuf
636# functions. See the mbuf(9) manpage for a list of available
637# test cases.
638options MBUF_STRESS_TEST
639
984263bc
MD
640# Statically link in accept filters
641options ACCEPT_FILTER_DATA
642options ACCEPT_FILTER_HTTP
643
644#
645# TCP_DROP_SYNFIN adds support for ignoring TCP packets with SYN+FIN. This
646# prevents nmap et al. from identifying the TCP/IP stack, but breaks support
647# for RFC1644 extensions and is not recommended for web servers.
648#
649options TCP_DROP_SYNFIN #drop TCP packets with SYN+FIN
650
651# ICMP_BANDLIM enables icmp error response bandwidth limiting. You
652# typically want this option as it will help protect the machine from
653# D.O.S. packet attacks.
654#
655options ICMP_BANDLIM
656
657# DUMMYNET enables the "dummynet" bandwidth limiter. You need
658# IPFIREWALL as well. See the dummynet(4) and ipfw(8) manpages for more info.
659# When you run DUMMYNET it is advisable to also have "options HZ=1000"
660# to achieve a smoother scheduling of the traffic.
661#
984263bc 662options DUMMYNET
984263bc
MD
663
664#
665# ATM (HARP version) options
666#
667# ATM_CORE includes the base ATM functionality code. This must be included
668# for ATM support.
669#
670# ATM_IP includes support for running IP over ATM.
671#
672# At least one (and usually only one) of the following signalling managers
673# must be included (note that all signalling managers include PVC support):
674# ATM_SIGPVC includes support for the PVC-only signalling manager `sigpvc'.
675# ATM_SPANS includes support for the `spans' signalling manager, which runs
676# the FORE Systems's proprietary SPANS signalling protocol.
677# ATM_UNI includes support for the `uni30' and `uni31' signalling managers,
678# which run the ATM Forum UNI 3.x signalling protocols.
679#
680# The `hea' driver provides support for the Efficient Networks, Inc.
681# ENI-155p ATM PCI Adapter.
682#
683# The `hfa' driver provides support for the FORE Systems, Inc.
684# PCA-200E ATM PCI Adapter.
685#
686options ATM_CORE #core ATM protocol family
687options ATM_IP #IP over ATM support
688options ATM_SIGPVC #SIGPVC signalling manager
689options ATM_SPANS #SPANS signalling manager
690options ATM_UNI #UNI signalling manager
691device hea #Efficient ENI-155p ATM PCI
692device hfa #FORE PCA-200E ATM PCI
693
694# DEVICE_POLLING adds support for mixed interrupt-polling handling
695# of network device drivers, which has significant benefits in terms
696# of robustness to overloads and responsivity, as well as permitting
697# accurate scheduling of the CPU time between kernel network processing
698# and other activities. The drawback is a moderate (up to 1/HZ seconds)
699# potential increase in response times.
a4e2e4c8 700#
984263bc 701# Additionally, you can enable/disable polling at runtime with the
a4e2e4c8
SZ
702# sysctl variable kern.polling.enable (defaults off), set polling
703# frequency with the sysctl variable kern.polling.pollhz (default 2000,
704# range 1..30000) and select the CPU fraction reserved to userland with
705# the sysctl variable kern.polling.user_frac (default 50, range 0..100).
706#
707# It is strongly recommended to set the sysctl variable kern.polling.pollhz
708# to 1000 or 2000 as to achieve smoother behaviour.
984263bc 709#
01fe1724
SW
710# Only the following devices support this mode of operation at the time of
711# this writing:
712#
42be0015 713# bce, bge, dc, em, fwe, fxp, nfe, nge, re, rl, sis, stge, vge, vr, wi, xl
984263bc
MD
714
715options DEVICE_POLLING
716
717\f
718#####################################################################
719# FILESYSTEM OPTIONS
720
721#
722# Only the root, /usr, and /tmp filesystems need be statically
723# compiled; everything else will be automatically loaded at mount
724# time. (Exception: the UFS family---FFS, and MFS --- cannot
725# currently be demand-loaded.) Some people still prefer to statically
726# compile other filesystems as well.
727#
36a06697 728# NB: The PORTAL and UNION filesystems are known to be
984263bc
MD
729# buggy, and WILL panic your system if you attempt to do anything with
730# them. They are included here as an incentive for some enterprising
731# soul to sit down and fix them.
732#
733
734# One of these is mandatory:
735options FFS #Fast filesystem
4ab1cc4a
DR
736options MFS #Memory filesystem
737options NFS #Network filesystem
984263bc
MD
738
739# The rest are optional:
740#options NFS_NOSERVER #Disable the NFS-server code.
741options CD9660 #ISO 9660 filesystem
742options FDESC #File descriptor filesystem
4ab1cc4a
DR
743options MSDOSFS #MS DOS filesystem
744options NTFS #NT filesystem
36a06697 745options NULLFS #NULL filesystem
984263bc
MD
746options NWFS #NetWare filesystem
747options PORTAL #Portal filesystem
748options PROCFS #Process filesystem
749options SMBFS #SMB/CIFS filesystem
4a77c3ab 750options UDF #UDF filesystem
03c6405b 751# YYY-DR Till we rework the VOP methods for this filesystem
03c6405b 752#options UNION #Union filesystem
984263bc 753# The xFS_ROOT options REQUIRE the associated ``options xFS''
984263bc
MD
754options FFS_ROOT #FFS usable as root device
755options NFS_ROOT #NFS usable as root device
756
4ab1cc4a 757# Soft updates is technique for improving filesystem speed and
984263bc
MD
758# making abrupt shutdown less risky.
759options SOFTUPDATES
760
761# Directory hashing improves the speed of operations on very large
762# directories at the expense of some memory.
763options UFS_DIRHASH
764
765# Make space in the kernel for a root filesystem on a md device.
766# Define to the number of kilobytes to reserve for the filesystem.
767options MD_ROOT_SIZE=10
768
769# Make the md device a potential root device, either with preloaded
770# images of type mfs_root or md_root.
771options MD_ROOT
772
773# Specify double the default maximum size for malloc(9)-backed md devices.
774options MD_NSECT=40000
775
776# Allow this many swap-devices.
777#
778# In order to manage swap, the system must reserve bitmap space that
779# scales with the largest mounted swap device multiplied by NSWAPDEV,
780# irregardless of whether other swap devices exist or not. So it
781# is not a good idea to make this value too large.
782options NSWAPDEV=5
783
784# Disk quotas are supported when this option is enabled.
785options QUOTA #enable disk quotas
786
787# If you are running a machine just as a fileserver for PC and MAC
788# users, using SAMBA or Netatalk, you may consider setting this option
789# and keeping all those users' directories on a filesystem that is
790# mounted with the suiddir option. This gives new files the same
791# ownership as the directory (similar to group). It's a security hole
792# if you let these users run programs, so confine it to file-servers
793# (but it'll save you lots of headaches in those cases). Root owned
794# directories are exempt and X bits are cleared. The suid bit must be
795# set on the directory as well; see chmod(1) PC owners can't see/set
796# ownerships so they keep getting their toes trodden on. This saves
797# you all the support calls as the filesystem it's used on will act as
798# they expect: "It's my dir so it must be my file".
799#
800options SUIDDIR
801
802# NFS options:
803options NFS_MINATTRTIMO=3 # VREG attrib cache timeout in sec
804options NFS_MAXATTRTIMO=60
805options NFS_MINDIRATTRTIMO=30 # VDIR attrib cache timeout in sec
806options NFS_MAXDIRATTRTIMO=60
807options NFS_GATHERDELAY=10 # Default write gather delay (msec)
808options NFS_UIDHASHSIZ=29 # Tune the size of nfssvc_sock with this
809options NFS_WDELAYHASHSIZ=16 # and with this
810options NFS_MUIDHASHSIZ=63 # Tune the size of nfsmount with this
811options NFS_DEBUG # Enable NFS Debugging
812
0e63c0c7
SW
813# MSDOSFS options:
814options MSDOSFS_DEBUG # Enable MSDOSFS Debugging
815
984263bc
MD
816#
817# Add support for the EXT2FS filesystem of Linux fame. Be a bit
818# careful with this - the ext2fs code has a tendency to lag behind
819# changes and not be exercised very much, so mounting read/write could
820# be dangerous (and even mounting read only could result in panics.)
821#
822options EXT2FS
823
824# Use real implementations of the aio_* system calls. There are numerous
825# stability and security issues in the current aio code that make it
826# unsuitable for inclusion on machines with untrusted local users.
827options VFS_AIO
828
829\f
830#####################################################################
831# POSIX P1003.1B
832
833# Real time extensions added in the 1993 Posix
834# P1003_1B: Infrastructure
835# _KPOSIX_PRIORITY_SCHEDULING: Build in _POSIX_PRIORITY_SCHEDULING
836# _KPOSIX_VERSION: Version kernel is built for
837
838options P1003_1B
839options _KPOSIX_PRIORITY_SCHEDULING
840options _KPOSIX_VERSION=199309L
841
842\f
843#####################################################################
844# CLOCK OPTIONS
845
846# The granularity of operation is controlled by the kernel option HZ whose
847# default value (100) means a granularity of 10ms (1s/HZ).
848# Some subsystems, such as DUMMYNET or DEVICE_POLLING, might benefit from
849# a smaller granularity such as 1ms or less.
850# Consider, however, that reducing the granularity too much might
851# cause excessive overhead in clock interrupt processing,
852# potentially causing ticks to be missed and thus actually reducing
853# the accuracy of operation.
854
855options HZ=100
856
857# The following options are used for debugging clock behavior only, and
858# should not be used for production systems.
859#
860# CLK_CALIBRATION_LOOP will run the clock calibration loop at startup
861# until the user presses a key.
862
863options CLK_CALIBRATION_LOOP
864
865# The following two options measure the frequency of the corresponding
866# clock relative to the RTC (onboard mc146818a).
867
868options CLK_USE_I8254_CALIBRATION
869options CLK_USE_TSC_CALIBRATION
870
871\f
872#####################################################################
873# SCSI DEVICES
874
875# SCSI DEVICE CONFIGURATION
876
877# The SCSI subsystem consists of the `base' SCSI code, a number of
878# high-level SCSI device `type' drivers, and the low-level host-adapter
879# device drivers. The host adapters are listed in the ISA and PCI
880# device configuration sections below.
881#
882# Beginning with FreeBSD 2.0.5 you can wire down your SCSI devices so
883# that a given bus, target, and LUN always come on line as the same
884# device unit. In earlier versions the unit numbers were assigned
885# in the order that the devices were probed on the SCSI bus. This
886# means that if you removed a disk drive, you may have had to rewrite
887# your /etc/fstab file, and also that you had to be careful when adding
888# a new disk as it may have been probed earlier and moved your device
889# configuration around.
890
891# This old behavior is maintained as the default behavior. The unit
892# assignment begins with the first non-wired down unit for a device
893# type. For example, if you wire a disk as "da3" then the first
894# non-wired disk will be assigned da4.
895
896# The syntax for wiring down devices is:
897
898# device scbus0 at ahc0 # Single bus device
899# device scbus1 at ahc1 bus 0 # Single bus device
900# device scbus3 at ahc2 bus 0 # Twin bus device
901# device scbus2 at ahc2 bus 1 # Twin bus device
902# device da0 at scbus0 target 0 unit 0
903# device da1 at scbus3 target 1
904# device da2 at scbus2 target 3
905# device sa1 at scbus1 target 6
906# device cd
907
908# "units" (SCSI logical unit number) that are not specified are
909# treated as if specified as LUN 0.
910
911# All SCSI devices allocate as many units as are required.
912
913# The "unknown" device (uk? in pre-2.0.5) is now part of the base SCSI
914# configuration and doesn't have to be explicitly configured.
915
916device scbus #base SCSI code
917device ch #SCSI media changers
918device da #SCSI direct access devices (aka disks)
919device sa #SCSI tapes
920device cd #SCSI CD-ROMs
921device pass #CAM passthrough driver
922device pt #SCSI processor type
923device ses #SCSI SES/SAF-TE driver
924
925# CAM OPTIONS:
926# debugging options:
927# -- NOTE -- If you specify one of the bus/target/lun options, you must
928# specify them all!
929# CAMDEBUG: When defined enables debugging macros
930# CAM_DEBUG_BUS: Debug the given bus. Use -1 to debug all busses.
931# CAM_DEBUG_TARGET: Debug the given target. Use -1 to debug all targets.
932# CAM_DEBUG_LUN: Debug the given lun. Use -1 to debug all luns.
933# CAM_DEBUG_FLAGS: OR together CAM_DEBUG_INFO, CAM_DEBUG_TRACE,
934# CAM_DEBUG_SUBTRACE, and CAM_DEBUG_CDB
935#
936# CAM_MAX_HIGHPOWER: Maximum number of concurrent high power (start unit) cmds
937# SCSI_NO_SENSE_STRINGS: When defined disables sense descriptions
938# SCSI_NO_OP_STRINGS: When defined disables opcode descriptions
939# SCSI_DELAY: The number of MILLISECONDS to freeze the SIM (scsi adapter)
940# queue after a bus reset, and the number of milliseconds to
941# freeze the device queue after a bus device reset.
942options CAMDEBUG
943options CAM_DEBUG_BUS=-1
944options CAM_DEBUG_TARGET=-1
945options CAM_DEBUG_LUN=-1
946options CAM_DEBUG_FLAGS="CAM_DEBUG_INFO|CAM_DEBUG_TRACE|CAM_DEBUG_CDB"
947options CAM_MAX_HIGHPOWER=4
948options SCSI_NO_SENSE_STRINGS
949options SCSI_NO_OP_STRINGS
950options SCSI_DELAY=8000 # Be pessimistic about Joe SCSI device
951
952# Options for the CAM CDROM driver:
953# CHANGER_MIN_BUSY_SECONDS: Guaranteed minimum time quantum for a changer LUN
954# CHANGER_MAX_BUSY_SECONDS: Maximum time quantum per changer LUN, only
955# enforced if there is I/O waiting for another LUN
956# The compiled in defaults for these variables are 2 and 10 seconds,
957# respectively.
958#
959# These can also be changed on the fly with the following sysctl variables:
960# kern.cam.cd.changer.min_busy_seconds
961# kern.cam.cd.changer.max_busy_seconds
962#
963options CHANGER_MIN_BUSY_SECONDS=2
964options CHANGER_MAX_BUSY_SECONDS=10
965
966# Options for the CAM sequential access driver:
967# SA_IO_TIMEOUT: Timeout for read/write/wfm operations, in minutes
968# SA_SPACE_TIMEOUT: Timeout for space operations, in minutes
969# SA_REWIND_TIMEOUT: Timeout for rewind operations, in minutes
970# SA_ERASE_TIMEOUT: Timeout for erase operations, in minutes
971# SA_1FM_AT_EOD: Default to model which only has a default one filemark at EOT.
972options SA_IO_TIMEOUT="(4)"
973options SA_SPACE_TIMEOUT="(60)"
974options SA_REWIND_TIMEOUT="(2*60)"
975options SA_ERASE_TIMEOUT="(4*60)"
976options SA_1FM_AT_EOD
977
978# Optional timeout for the CAM processor target (pt) device
979# This is specified in seconds. The default is 60 seconds.
980options SCSI_PT_DEFAULT_TIMEOUT="60"
981
982# Optional enable of doing SES passthrough on other devices (e.g., disks)
983#
984# Normally disabled because a lot of newer SCSI disks report themselves
985# as having SES capabilities, but this can then clot up attempts to build
986# build a topology with the SES device that's on the box these drives
987# are in....
988options SES_ENABLE_PASSTHROUGH
989
990\f
991#####################################################################
992# MISCELLANEOUS DEVICES AND OPTIONS
993
994# The `pty' device usually turns out to be ``effectively mandatory'',
995# as it is required for `telnetd', `rlogind', `screen', `emacs', and
996# `xterm', among others.
997
998pseudo-device pty #Pseudo ttys
984263bc
MD
999pseudo-device gzip #Exec gzipped a.out's
1000pseudo-device vn #Vnode driver (turns a file into a device)
1001pseudo-device md #Memory/malloc disk
1002pseudo-device snp #Snoop device - to look at pty/vty/etc..
1003pseudo-device ccd 4 #Concatenated disk driver
1004
1005# Configuring Vinum into the kernel is not necessary, since the kld
1006# module gets started automatically when vinum(8) starts. This
1007# device is also untested. Use at your own risk.
1008#
1009# The option VINUMDEBUG must match the value set in CFLAGS
1010# in src/sbin/vinum/Makefile. Failure to do so will result in
1011# the following message from vinum(8):
1012#
1013# Can't get vinum config: Invalid argument
1014#
1015# see vinum(4) for more reasons not to use these options.
1016pseudo-device vinum #Vinum concat/mirror/raid driver
1017options VINUMDEBUG #enable Vinum debugging hooks
1018
1019# Kernel side iconv library
1020options LIBICONV
1021
1022# Size of the kernel message buffer. Should be N * pagesize.
1023options MSGBUF_SIZE=40960
1024
1025\f
1026#####################################################################
1027# HARDWARE DEVICE CONFIGURATION
1028
1029# ISA and EISA devices:
1030# EISA support is available for some device, so they can be auto-probed.
984263bc
MD
1031
1032#
1033# Mandatory ISA devices: isa, npx
1034#
1035device isa
1036
0e1cb2e2
JS
1037# ISA-PnP BIOS support
1038device pnpbios
1039
984263bc
MD
1040#
1041# Options for `isa':
1042#
1043# AUTO_EOI_1 enables the `automatic EOI' feature for the master 8259A
1044# interrupt controller. This saves about 0.7-1.25 usec for each interrupt.
1045# This option breaks suspend/resume on some portables.
1046#
1047# AUTO_EOI_2 enables the `automatic EOI' feature for the slave 8259A
1048# interrupt controller. This saves about 0.7-1.25 usec for each interrupt.
1049# Automatic EOI is documented not to work for for the slave with the
1050# original i8259A, but it works for some clones and some integrated
1051# versions.
1052#
1053# MAXMEM specifies the amount of RAM on the machine; if this is not
1054# specified, FreeBSD will first read the amount of memory from the CMOS
1055# RAM, so the amount of memory will initially be limited to 64MB or 16MB
1056# depending on the BIOS. If the BIOS reports 64MB, a memory probe will
1057# then attempt to detect the installed amount of RAM. If this probe
1058# fails to detect >64MB RAM you will have to use the MAXMEM option.
1059# The amount is in kilobytes, so for a machine with 128MB of RAM, it would
1060# be 131072 (128 * 1024).
1061#
1062# BROKEN_KEYBOARD_RESET disables the use of the keyboard controller to
1063# reset the CPU for reboot. This is needed on some systems with broken
1064# keyboard controllers.
1065#
1066# PAS_JOYSTICK_ENABLE enables the gameport on the ProAudio Spectrum
1067
66cc79ca 1068options COMPAT_OLDISA #FreeBSD 2.2 and 3.x compatibility shims
984263bc
MD
1069options AUTO_EOI_1
1070#options AUTO_EOI_2
1071options MAXMEM="(128*1024)"
1072#options BROKEN_KEYBOARD_RESET
1073#options PAS_JOYSTICK_ENABLE
1074
1075# Enable support for the kernel PLL to use an external PPS signal,
1076# under supervision of [x]ntpd(8)
1077# More info in ntpd documentation: http://www.eecis.udel.edu/~ntp
1078
1079options PPS_SYNC
1080
984263bc
MD
1081# The keyboard controller; it controls the keyboard and the PS/2 mouse.
1082device atkbdc0 at isa? port IO_KBD
1083
1084# The AT keyboard
1085device atkbd0 at atkbdc? irq 1
1086
1087# Options for atkbd:
1088options ATKBD_DFLT_KEYMAP # specify the built-in keymap
1089makeoptions ATKBD_DFLT_KEYMAP="jp.106"
1090
1091# These options are valid for other keyboard drivers as well.
1092options KBD_DISABLE_KEYMAP_LOAD # refuse to load a keymap
1093options KBD_INSTALL_CDEV # install a CDEV entry in /dev
1094
1095# `flags' for atkbd:
1096# 0x01 Force detection of keyboard, else we always assume a keyboard
1097# 0x02 Don't reset keyboard, useful for some newer ThinkPads
1098# 0x03 Force detection and avoid reset, might help with certain
1099# dockingstations
1100# 0x04 Old-style (XT) keyboard support, useful for older ThinkPads
1101
1102# PS/2 mouse
1103device psm0 at atkbdc? irq 12
1104
1105# Options for psm:
1106options PSM_HOOKRESUME #hook the system resume event, useful
1107 #for some laptops
1108options PSM_RESETAFTERSUSPEND #reset the device at the resume event
1109
1110# The video card driver.
1111device vga0 at isa?
1112
1113# Options for vga:
1114# Try the following option if the mouse pointer is not drawn correctly
1115# or font does not seem to be loaded properly. May cause flicker on
1116# some systems.
1117options VGA_ALT_SEQACCESS
1118
9c06b297
SW
1119options VGA_DEBUG=2 # enable VGA debug output
1120
984263bc
MD
1121# If you can dispense with some vga driver features, you may want to
1122# use the following options to save some memory.
6fbe6059
SW
1123#options VGA_NO_FONT_LOADING # don't save/load font
1124#options VGA_NO_MODE_CHANGE # don't change video modes
984263bc
MD
1125
1126# Older video cards may require this option for proper operation.
1127options VGA_SLOW_IOACCESS # do byte-wide i/o's to TS and GDC regs
1128
1129# The following option probably won't work with the LCD displays.
1130options VGA_WIDTH90 # support 90 column modes
1131
1132# To include support for VESA video modes
1133options VESA
9c06b297
SW
1134options VESA_DEBUG=2 # enable VESA debug output
1135
984263bc
MD
1136# Splash screen at start up! Screen savers require this too.
1137pseudo-device splash
1138
984263bc
MD
1139# The syscons console driver (sco color console compatible).
1140device sc0 at isa?
1141options MAXCONS=16 # number of virtual consoles
1142options SC_ALT_MOUSE_IMAGE # simplified mouse cursor in text mode
9c06b297 1143options SC_DEBUG_LEVEL=5 # enable debug output
984263bc
MD
1144options SC_DFLT_FONT # compile font in
1145makeoptions SC_DFLT_FONT=cp850
1146options SC_DISABLE_DDBKEY # disable `debug' key
1147options SC_DISABLE_REBOOT # disable reboot key sequence
1148options SC_HISTORY_SIZE=200 # number of history buffer lines
1149options SC_MOUSE_CHAR=0x3 # char code for text mode mouse cursor
1150options SC_PIXEL_MODE # add support for the raster text mode
1151
1152# The following options will let you change the default colors of syscons.
1153options SC_NORM_ATTR="(FG_GREEN|BG_BLACK)"
1154options SC_NORM_REV_ATTR="(FG_YELLOW|BG_GREEN)"
1155options SC_KERNEL_CONS_ATTR="(FG_RED|BG_BLACK)"
1156options SC_KERNEL_CONS_REV_ATTR="(FG_BLACK|BG_RED)"
1157
1158# If you have a two button mouse, you may want to add the following option
1159# to use the right button of the mouse to paste text.
1160options SC_TWOBUTTON_MOUSE
1161
1162# You can selectively disable features in syscons.
6fbe6059
SW
1163#options SC_NO_CUTPASTE
1164#options SC_NO_FONT_LOADING
1165#options SC_NO_HISTORY
1166#options SC_NO_SYSMOUSE
984263bc
MD
1167
1168#
1169# The Numeric Processing eXtension driver. In addition to this, you
1170# may configure a math emulator (see above). If your machine has a
1171# hardware FPU and the kernel configuration includes the npx device
1172# *and* a math emulator compiled into the kernel, the hardware FPU
1173# will be used, unless it is found to be broken or unless "flags" to
1174# npx0 includes "0x08", which requests preference for the emulator.
1175device npx0 at nexus? port IO_NPX flags 0x0 irq 13
1176
1177#
1178# `flags' for npx0:
1179# 0x01 don't use the npx registers to optimize bcopy.
1180# 0x02 don't use the npx registers to optimize bzero.
1181# 0x04 don't use the npx registers to optimize copyin or copyout.
1182# 0x08 use emulator even if hardware FPU is available.
1183# The npx registers are normally used to optimize copying and zeroing when
1184# all of the following conditions are satisfied:
1185# I586_CPU is an option
1186# the cpu is an i586 (perhaps not a Pentium)
1187# the probe for npx0 succeeds
1188# INT 16 exception handling works.
1189# Then copying and zeroing using the npx registers is normally 30-100% faster.
1190# The flags can be used to control cases where it doesn't work or is slower.
1191# Setting them at boot time using userconfig works right (the optimizations
1192# are not used until later in the bootstrap when npx0 is attached).
1193# Flag 0x08 automatically disables the i586 optimized routines.
1194#
1195
1196#
1197# Optional ISA and EISA devices:
1198#
1199
1200#
1201# SCSI host adapters: `aha', `aic', `bt'
1202#
1203# adv: All Narrow SCSI bus AdvanSys controllers.
1204# adw: Second Generation AdvanSys controllers including the ADV940UW.
1205# aha: Adaptec 154x
1206# ahc: Adaptec 274x/284x/294x
1207# aic: Adaptec 152x
1208# bt: Most Buslogic controllers
1209# ncv: NCR 53C500 based SCSI host adapters.
1210# nsp: Workbit Ninja SCSI-3 based PC Card SCSI host adapters.
1211# stg: TMC 18C30, 18C50 based ISA/PC Card SCSI host adapters.
1212#
1213# Note that the order is important in order for Buslogic cards to be
1214# probed correctly.
1215#
1216
1217device bt0 at isa? port IO_BT0
1218device adv0 at isa?
1219device adw
1220device aha0 at isa?
1221device aic0 at isa?
1222device ncv
1223device nsp
1224device stg0 at isa? port 0x140 irq 11
1225
1226#
1227# Adaptec FSA RAID controllers, including integrated DELL controller,
1228# the Dell PERC 2/QC and the HP NetRAID-4M
1229#
1230device aac
1231device aacp # SCSI Passthrough interface (optional, CAM required)
1232
1233#
1234# Compaq Smart RAID, Mylex DAC960 and AMI MegaRAID controllers. Only
1235# one entry is needed; the code will find and configure all supported
1236# controllers.
1237#
1238device ida # Compaq Smart RAID
1239device mlx # Mylex DAC960
1240device amr # AMI MegaRAID
1241
1242#
1243# 3ware ATA RAID
1244#
1245device twe # 3ware ATA RAID
ab443496 1246device twa # 3ware SATA RAID
4ad6607f
SW
1247options TWA_DEBUG=10 # enable debug messages
1248options TWA_FLASH_FIRMWARE
984263bc 1249
e6f8991b
DR
1250#
1251# Promise Supertrack SX6000
1252#
1253device pst
1254
2114ec03
DR
1255#
1256# IBM ServeRAID
1257#
1258device ips
1259
984263bc
MD
1260#
1261# The 'ATA' driver supports all ATA and ATAPI devices.
984263bc
MD
1262# You only need one "device ata" for it to find all
1263# PCI ATA/ATAPI devices on modern machines.
f203b3ea
SW
1264#device ata
1265#device atadisk # ATA disk drives
1266#device atapicd # ATAPI CDROM drives
1267#device atapifd # ATAPI floppy drives
1268#device atapist # ATAPI tape drives
1269#device atapicam # emulate ATAPI devices as SCSI ditto via CAM
984263bc 1270 # needs CAM to be present (scbus & pass)
4068acee
TS
1271# The 'NATA' set of drivers are set to replace the previous ATA drivers,
1272# and this set of drivers is mutually exclusive with the old ones. This means,
1273# you can't have both at the same time!
f203b3ea
SW
1274device nata
1275device natadisk # ATA disk drives
1276device natapicd # ATAPI CD/DVD drives
1277device natapifd # ATAPI floppy drives
1278device natapist # ATAPI tape drives
1279device natapicam # ATAPI CAM layer emulation
1280device nataraid # support for ATA software RAID controllers
1281device natausb # ATA-over-USB support
984263bc
MD
1282
1283#The following options are valid on the ATA driver:
1284#
1285# ATA_STATIC_ID: controller numbering is static (like the old driver)
1286# else the device numbers are dynamically allocated.
1287options ATA_STATIC_ID
1288
1289#
1290# For older non-PCI systems, these are the lines to use:
1291#device ata0 at isa? port IO_WD1 irq 14
1292#device ata1 at isa? port IO_WD2 irq 15
1293
984263bc
MD
1294#
1295# Standard floppy disk controllers: `fdc' and `fd'
1296#
1297device fdc0 at isa? port IO_FD1 irq 6 drq 2
1298#
1299# FDC_DEBUG enables floppy debugging. Since the debug output is huge, you
1300# gotta turn it actually on by setting the variable fd_debug with DDB,
1301# however.
1302options FDC_DEBUG
1303
1304device fd0 at fdc0 drive 0
1305device fd1 at fdc0 drive 1
1306
984263bc
MD
1307#
1308# Other standard PC hardware: `mse', `sio', etc.
1309#
1310# mse: Logitech and ATI InPort bus mouse ports
1311# sio: serial ports (see sio(4))
1312
1313device mse0 at isa? port 0x23c irq 5
1314
1315device sio0 at isa? port IO_COM1 flags 0x10 irq 4
1316
1317#
1318# `flags' for serial drivers that support consoles (only for sio now):
1319# 0x10 enable console support for this unit. The other console flags
1320# are ignored unless this is set. Enabling console support does
1321# not make the unit the preferred console - boot with -h or set
1322# the 0x20 flag for that. Currently, at most one unit can have
1323# console support; the first one (in config file order) with
1324# this flag set is preferred. Setting this flag for sio0 gives
1325# the old behaviour.
1326# 0x20 force this unit to be the console (unless there is another
1327# higher priority console). This replaces the COMCONSOLE option.
1328# 0x40 reserve this unit for low level console operations. Do not
1329# access the device in any normal way.
1330# 0x80 use this port for serial line gdb support in ddb.
1331#
1332# PnP `flags' (set via userconfig using pnp x flags y)
1333# 0x1 disable probing of this device. Used to prevent your modem
1334# from being attached as a PnP modem.
1335#
1336
1337# Options for serial drivers that support consoles (only for sio now):
1338options BREAK_TO_DEBUGGER #a BREAK on a comconsole goes to
1339 #DDB, if available.
1340options CONSPEED=115200 # speed for serial console
1341 # (default 9600)
1342
1343# Solaris implements a new BREAK which is initiated by a character
1344# sequence CR ~ ^b which is similar to a familiar pattern used on
1345# Sun servers by the Remote Console.
1346options ALT_BREAK_TO_DEBUGGER
1347
1348# Options for sio:
1349options COM_ESP #code for Hayes ESP
1350options COM_MULTIPORT #code for some cards with shared IRQs
1351
1352# Other flags for sio that aren't documented in the man page.
1353# 0x20000 enable hardware RTS/CTS and larger FIFOs. Only works for
1354# ST16650A-compatible UARTs.
1355
1356# PCI Universal Communications driver
1357# Supports various single and multi port PCI serial cards. Maybe later
1358# also the parallel ports on combination serial/parallel cards. New cards
1359# can be added in src/sys/dev/puc/pucdata.c.
1360#
1361# If the PUC_FASTINTR option is used the driver will try to use fast
1362# interrupts. The card must then be the only user of that interrupt.
1363# Interrupts cannot be shared when using PUC_FASTINTR.
1364device puc
1365options PUC_FASTINTR
1366
1367#
1368# Network interfaces: `cx', `ed', `el', `ep', `ie', `is', `le', `lnc'
1369#
1370# ar: Arnet SYNC/570i hdlc sync 2/4 port V.35/X.21 serial driver (requires sppp)
984263bc
MD
1371# cs: IBM Etherjet and other Crystal Semi CS89x0-based adapters
1372# cx: Cronyx/Sigma multiport sync/async (with Cisco or PPP framing)
1373# ed: Western Digital and SMC 80xx; Novell NE1000 and NE2000; 3Com 3C503
1374# el: 3Com 3C501 (slow!)
1375# ep: 3Com 3C509
1376# ex: Intel EtherExpress Pro/10 and other i82595-based adapters
1377# fe: Fujitsu MB86960A/MB86965A Ethernet
1378# ie: AT&T StarLAN 10 and EN100; 3Com 3C507; unknown NI5210; Intel EtherExpress
1379# le: Digital Equipment EtherWorks 2 and EtherWorks 3 (DEPCA, DE100,
1380# DE101, DE200, DE201, DE202, DE203, DE204, DE205, DE422)
1381# lnc: Lance/PCnet cards (Isolan, Novell NE2100, NE32-VL, AMD Am7990 & Am79C960)
1382# rdp: RealTek RTL 8002-based pocket ethernet adapters
1383# sbni: Granch SBNI12-xx adapters
1384# sbsh: Granch SBNI16 SHDSL modem PCI adapters
1385# sr: RISCom/N2 hdlc sync 1/2 port V.35/X.21 serial driver (requires sppp)
1386# wl: Lucent Wavelan (ISA card only).
1387# awi: IEEE 802.11b PRISM I cards.
1388# wi: Lucent WaveLAN/IEEE 802.11 PCMCIA adapters. Note: this supports both
1389# the PCMCIA and ISA cards: the ISA card is really a PCMCIA to ISA
1390# bridge with a PCMCIA adapter plugged into it.
1391# an: Aironet 4500/4800 802.11 wireless adapters. Supports the PCMCIA,
1392# PCI and ISA varieties.
1393# xe: Xircom/Intel EtherExpress Pro100/16 PC Card ethernet controller.
1394# ray: Raytheon Raylink 802.11 wireless NICs, OEM as Webgear Aviator 2.4GHz
984263bc
MD
1395#
1396device ar0 at isa? port 0x300 irq 10 iomem 0xd0000
984263bc
MD
1397device cs0 at isa? port 0x300
1398device cx0 at isa? port 0x240 irq 15 drq 7
1399device ed0 at isa? port 0x280 irq 5 iomem 0xd8000
1400device el0 at isa? port 0x300 irq 9
1401device ep
1402device ex
1403device fe0 at isa? port 0x300
1404device ie0 at isa? port 0x300 irq 5 iomem 0xd0000
1405device ie1 at isa? port 0x360 irq 7 iomem 0xd0000
1406device le0 at isa? port 0x300 irq 5 iomem 0xd0000
1407device lnc0 at isa? port 0x280 irq 10 drq 0
1408device rdp0 at isa? port 0x378 irq 7 flags 2
1409device sbni0 at isa? port 0x210 irq 5 flags 0xefdead
1410device sr0 at isa? port 0x300 irq 5 iomem 0xd0000
1411device sn0 at isa? port 0x300 irq 10
d8a8ea86
JR
1412
1413# Wlan support is mandatory for some wireless LAN devices.
841ab66c
SZ
1414device wlan # 802.11 support
1415device wlan_acl # 802.11 MAC-based access control for AP
1416device wlan_ccmp # 802.11 CCMP support
1417device wlan_tkip # 802.11 TKIP support
1418device wlan_wep # 802.11 WEP support
1419device wlan_xauth # 802.11 WPA or 802.1x authentication for AP
b9334f94
SZ
1420device wlan_ratectl_onoe # 802.11 Onoe TX rate control algorithm
1421device wlan_ratectl_amrr # 802.11 AMRR TX rate control algorithm
0dba45fe 1422device wlan_ratectl_sample # 802.11 Sample TX rate control algorithm
984263bc
MD
1423options WLCACHE # enables the signal-strength cache
1424options WLDEBUG # enables verbose debugging output
45e7728a 1425device awi # AMD PCnetMobile
d8a8ea86
JR
1426device an # Aironet Communications 4500/4800
1427device ipw # Intel PRO/Wireless 2100
1428device iwi # Intel PRO/Wireless 2200BG/2915ABG
1429device wi # WaveLAN/IEEE, PRISM-II, Spectrum24 802.11DS
44db266b 1430device rtw # RealTek 8180
2fc6d79d 1431 # Requires wlan_ratectl_onoe and wlan_wep
e9102f16
SZ
1432device acx # TI ACX100/ACX111.
1433 # Requires wlan_ratectl_amrr and
1434 # wlan_ratectl_onoe
d8a8ea86
JR
1435device wl0 at isa? port 0x300 # T1 speed ISA/radio lan
1436device xe # Xircom PCMCIA
1437device ray # Raytheon Raylink/Webgear Aviator
5fdff524 1438device ral # Ralink Technology 802.11 wireless NIC
0dba45fe
SZ
1439 # Requires wlan_ratectl_onoe and
1440 # wlan_ratectl_sample
984263bc 1441
984263bc
MD
1442#
1443# ATM related options
1444#
1445# The `en' device provides support for Efficient Networks (ENI)
1446# ENI-155 PCI midway cards, and the Adaptec 155Mbps PCI ATM cards (ANA-59x0).
1447#
1448# atm pseudo-device provides generic atm functions and is required for
1449# atm devices.
1450# NATM enables the netnatm protocol family that can be used to
1451# bypass TCP/IP.
1452#
1453# the current driver supports only PVC operations (no atm-arp, no multicast).
1454# for more details, please read the original documents at
1455# http://www.ccrc.wustl.edu/pub/chuck/tech/bsdatm/bsdatm.html
1456#
1457pseudo-device atm
1458device en
1459options NATM #native ATM
1460
e798f335 1461# Sound drivers
984263bc
MD
1462#
1463# The flags of the device tells the device a bit more info about the
1464# device that normally is obtained through the PnP interface.
1465# bit 2..0 secondary DMA channel;
1466# bit 4 set if the board uses two dma channels;
1467# bit 15..8 board type, overrides autodetection; leave it
1468# zero if don't know what to put in (and you don't,
1469# since this is unsupported at the moment...).
1470#
e798f335
JS
1471# This driver will use the new PnP code if it's available. You might
1472# need PNPBIOS for ISA devices.
984263bc 1473#
984263bc
MD
1474# If you have a GUS-MAX card and want to use the CS4231 codec on the
1475# card the drqs for the gus max must be 8 bit (1, 2, or 3).
1476#
1477# If you would like to use the full duplex option on the gus, then define
1478# flags to be the ``read dma channel''.
1479#
984263bc 1480
558a398b 1481# Basic sound card support:
984263bc 1482device pcm
6ceb4487 1483# For PnP/PCI sound cards:
e2339ccc 1484device "snd_ad1816"
558a398b
SS
1485device "snd_als4000"
1486device "snd_atiixp"
1487device "snd_cmi"
1488device "snd_cs4281"
1489device "snd_csa"
1490device "snd_ds1"
1491device "snd_emu10k1"
1492device "snd_es137x"
e2339ccc 1493device "snd_ess"
558a398b 1494device "snd_fm801"
e2339ccc 1495device "snd_hda"
558a398b
SS
1496device "snd_ich"
1497device "snd_maestro"
1498device "snd_maestro3"
e2339ccc 1499device "snd_mss"
558a398b 1500device "snd_neomagic"
e2339ccc
SW
1501device "snd_sb16"
1502device "snd_sb8"
1503device "snd_sbc"
558a398b
SS
1504device "snd_solo"
1505device "snd_t4dwave"
1506device "snd_via8233"
1507device "snd_via82c686"
1508device "snd_vibes"
e798f335 1509# For non-pnp sound cards:
558a398b 1510device pcm0 at isa? irq 10 drq 1 flags 0x0
e2339ccc 1511# USB
558a398b 1512device "snd_uaudio"
984263bc 1513
984263bc
MD
1514#
1515# Miscellaneous hardware:
1516#
984263bc
MD
1517# wt: Wangtek and Archive QIC-02/QIC-36 tape drives
1518# ctx: Cortex-I frame grabber
1519# apm: Laptop Advanced Power Management (experimental)
1520# spigot: The Creative Labs Video Spigot video-acquisition board
1521# meteor: Matrox Meteor video capture board
1522# bktr: Brooktree bt848/848a/849a/878/879 video capture and TV Tuner board
1523# cy: Cyclades serial driver
1524# dgb: Digiboard PC/Xi and PC/Xe series driver (ALPHA QUALITY!)
1525# dgm: Digiboard PC/Xem driver
1526# gp: National Instruments AT-GPIB and AT-GPIB/TNT board
1527# asc: GI1904-based hand scanners, e.g. the Trust Amiscan Grey
1528# gsc: Genius GS-4500 hand scanner.
1529# joy: joystick
1530# labpc: National Instrument's Lab-PC and Lab-PC+
1531# rc: RISCom/8 multiport card
1532# rp: Comtrol Rocketport(ISA) - single card
1533# tw: TW-523 power line interface for use with X-10 home control products
1534# si: Specialix SI/XIO 4-32 port terminal multiplexor
1535# spic: Sony Programmable I/O controller (VAIO notebooks)
1536# stl: Stallion EasyIO and EasyConnection 8/32 (ISA and PCI), EasyConnection 8/64 PCI
1537# stli: Stallion EasyConnection 8/64 ISA/EISA, ONboard, Brumby (intelligent)
1538# nmdm: nullmodem terminal driver (see nmdm(4))
1539
1540# Notes on APM
1541# The flags takes the following meaning for apm0:
1542# 0x0020 Statclock is broken.
1543# If apm is omitted, some systems require sysctl -w kern.timecounter.method=1
1544# for correct timekeeping.
1545
1546# Notes on the spigot:
1547# The video spigot is at 0xad6. This port address can not be changed.
1548# The irq values may only be 10, 11, or 15
1549# I/O memory is an 8kb region. Possible values are:
1550# 0a0000, 0a2000, ..., 0fffff, f00000, f02000, ..., ffffff
1551# The start address must be on an even boundary.
1552# Add the following option if you want to allow non-root users to be able
1553# to access the spigot. This option is not secure because it allows users
1554# direct access to the I/O page.
1555# options SPIGOT_UNSECURE
1556
1557# Notes on the Comtrol Rocketport driver:
1558#
1559# The exact values used for rp0 depend on how many boards you have
1560# in the system. The manufacturer's sample configs are listed as:
1561#
1562# Comtrol Rocketport ISA single card
1563# device rp0 at isa? port 0x280
1564#
1565# If instead you have two ISA cards, one installed at 0x100 and the
1566# second installed at 0x180, then you should add the following to
1567# your kernel configuration file:
1568#
1569# device rp0 at isa? port 0x100
1570# device rp1 at isa? port 0x180
1571#
1572# For 4 ISA cards, it might be something like this:
1573#
1574# device rp0 at isa? port 0x180
1575# device rp1 at isa? port 0x100
1576# device rp2 at isa? port 0x340
1577# device rp3 at isa? port 0x240
1578#
1579# And for PCI cards, you only need say:
1580#
1581# device rp
1582
1583# Notes on the Digiboard driver:
1584#
1585# The following flag values have special meanings:
1586# 0x01 - alternate layout of pins (dgb & dgm)
1587# 0x02 - use the windowed PC/Xe in 64K mode (dgb only)
1588
1589# Notes on the Specialix SI/XIO driver:
1590# **This is NOT a Specialix supported Driver!**
1591# The host card is memory, not IO mapped.
1592# The Rev 1 host cards use a 64K chunk, on a 32K boundary.
1593# The Rev 2 host cards use a 32K chunk, on a 32K boundary.
1594# The cards can use an IRQ of 11, 12 or 15.
1595
1596# Notes on the Stallion stl and stli drivers:
1597# See src/i386/isa/README.stl for complete instructions.
1598# This is version 2.0.0, unsupported by Stallion.
1599# The stl driver has a secondary IO port hard coded at 0x280. You need
1600# to change src/i386/isa/stallion.c if you reconfigure this on the boards.
1601# The "flags" and "iosiz" settings on the stli driver depend on the board:
1602# EasyConnection 8/64 ISA: flags 23 iosiz 0x1000
1603# EasyConnection 8/64 EISA: flags 24 iosiz 0x10000
984263bc
MD
1604# ONboard ISA: flags 4 iosiz 0x10000
1605# ONboard EISA: flags 7 iosiz 0x10000
984263bc
MD
1606# Brumby: flags 2 iosiz 0x4000
1607# Stallion: flags 1 iosiz 0x10000
1608# For the PCI cards, "device stl" will suffice.
1609
984263bc
MD
1610# for the SoundBlaster 16 multicd - up to 4 devices
1611device wt0 at isa? port 0x300 irq 5 drq 1
1612device ctx0 at isa? port 0x230 iomem 0xd0000
1613device spigot0 at isa? port 0xad6 irq 15 iomem 0xee000
1614device apm0
1615device gp0 at isa? port 0x2c0
1616device gsc0 at isa? port IO_GSC1 drq 3
1617device joy0 at isa? port IO_GAME
1618device cy0 at isa? irq 10 iomem 0xd4000 iosiz 0x2000
1619options CY_PCI_FASTINTR # Use with cy_pci unless irq is shared
49ec7c3b
JS
1620#device dgb0 at isa? port 0x220 iomem 0xfc000
1621#options NDGBPORTS=16 # Defaults to 16*NDGB
984263bc
MD
1622device dgm0 at isa? port 0x104 iomem 0xd0000
1623device labpc0 at isa? port 0x260 irq 5
1624device rc0 at isa? port 0x220 irq 12
49ec7c3b
JS
1625device nrp
1626#device rp0 at isa? port 0x280
984263bc
MD
1627# the port and irq for tw0 are fictitious
1628device tw0 at isa? port 0x380 irq 11
1629device si0 at isa? iomem 0xd0000 irq 12
1630device asc0 at isa? port IO_ASC1 drq 3 irq 10
1631device spic0 at isa? irq 0 port 0x10a0
1632device stl0 at isa? port 0x2a0 irq 10
1633device stli0 at isa? port 0x2a0 iomem 0xcc000 flags 23 iosiz 0x1000
984263bc
MD
1634# HOT1 Xilinx 6200 card (http://www.vcc.com/)
1635device xrpu
1636# nullmodem terminal driver
1637device nmdm
1638
984263bc
MD
1639#
1640# EISA devices:
1641#
1642# The EISA bus device is `eisa'. It provides auto-detection and
1643# configuration support for all devices on the EISA bus.
1644#
1645# The `ahb' device provides support for the Adaptec 174X adapter.
1646#
1647# The `ahc' device provides support for the Adaptec 274X and 284X
1648# adapters. The 284X, although a VLB card, responds to EISA probes.
984263bc
MD
1649device eisa
1650device ahb
1651device ahc
984263bc
MD
1652
1653# The aic7xxx driver will attempt to use memory mapped I/O for all PCI
1654# controllers that have it configured only if this option is set. Unfortunately,
1655# this doesn't work on some motherboards, which prevents it from being the
1656# default.
1657options AHC_ALLOW_MEMIO
1658
1659# The adw driver will attempt to use memory mapped I/O for all PCI
1660# controllers that have it configured only if this option is set.
1661options ADW_ALLOW_MEMIO
1662
1663# By default, only 10 EISA slots are probed, since the slot numbers
1664# above clash with the configuration address space of the PCI subsystem,
1665# and the EISA probe is not very smart about this. This is sufficient
1666# for most machines, but in particular the HP NetServer LC series comes
1667# with an onboard AIC7770 dual-channel SCSI controller on EISA slot #11,
1668# thus you need to bump this figure to 12 for them.
1669options EISA_SLOTS=12
1670
1671#
1672# PCI devices & PCI options:
1673#
1674# The main PCI bus device is `pci'. It provides auto-detection and
1675# configuration support for all devices on the PCI bus, using either
1676# configuration mode defined in the PCI specification.
1677
1678device pci
1679
1680# PCI options
1681#
7fe5a2bd
MD
1682#Enable pci resources left off by a "lazy" BIOS.
1683#
1684#WARNING! PCI_ENABLE_IO_MODES IS A VERY DANGEROUS OPTION AND MANY
1685#SYSTEMS WILL EXPERIENCE INSTABILITY WITH IT ON. USE ONLY AS A LAST
1686#RESORT!
1687#
984263bc
MD
1688options PCI_ENABLE_IO_MODES
1689#options PCI_QUIET #quiets PCI code on chipset settings
dc5a7bd2 1690options COMPAT_OLDPCI #FreeBSD 2.2 and 3.x compatibility shims
f203b3ea 1691options PCI_MAP_FIXUP #fixup lazy PCI mappings for certain devices,
4068acee
TS
1692 #e.g. ATA controllers in legacy mode. NATA
1693 #requires this, don't use it with old ATA!
984263bc
MD
1694
1695# AGP GART support
1696#
1697device agp
1698
1699
1700# The `ahc' device provides support for the Adaptec 29/3940(U)(W)
1701# and motherboard based AIC7870/AIC7880 adapters.
4ad6607f
SW
1702options AHC_DEBUG
1703options AHC_DEBUG_OPTS=0xffffffff
1704options AHC_REG_PRETTY_PRINT
1705options AHC_TMODE_ENABLE
984263bc
MD
1706#
1707# The 'ahd' device provides support for the Adaptec 79xx Ultra320
1708# SCSI adapters. Options are documented in the ahd(4) manpage:
1709options AHD_DEBUG
1710options AHD_DEBUG_OPTS=0xffffffff
1711options AHD_REG_PRETTY_PRINT
1712#options AHD_TMODE_ENABLE=0xff
1713#
1714# The `amd' device provides support for the AMD 53C974 SCSI host
1715# adapter chip as found on devices such as the Tekram DC-390(T).
1716#
1717# The `bge' device provides support for gigabit ethernet adapters
3f625015 1718# based on the Broadcom BCM570x family of controllers, including the
984263bc
MD
1719# 3Com 3c996-T, the Netgear GA302T, the SysKonnect SK-9D21 and SK-9D41,
1720# and the embedded gigE NICs on Dell PowerEdge 2550 servers.
1721#
1722# The `ncr' device provides support for the NCR 53C810 and 53C825
1723# self-contained SCSI host adapters.
1724#
1725# The `isp' device provides support for the Qlogic ISP 1020, 1040
1726# nd 1040B PCI SCSI host adapters, ISP 1240 Dual Ultra SCSI,
1727# ISP 1080 and 1280 (Dual) Ultra2, ISP 12160 Ultra3 SCSI, as well as
1728# the Qlogic ISP 2100 and ISP 2200 Fibre Channel Host Adapters.
1729#
1730# The `dc' device provides support for PCI fast ethernet adapters
1731# based on the DEC/Intel 21143 and various workalikes including:
1732# the ADMtek AL981 Comet and AN985 Centaur, the ASIX Electronics
1733# AX88140A and AX88141, the Davicom DM9100 and DM9102, the Lite-On
1734# 82c168 and 82c169 PNIC, the Lite-On/Macronix LC82C115 PNIC II
1735# and the Macronix 98713/98713A/98715/98715A/98725 PMAC. This driver
1736# replaces the old al, ax, dm, pn and mx drivers. List of brands:
1737# Digital DE500-BA, Kingston KNE100TX, D-Link DFE-570TX, SOHOware SFA110,
1738# SVEC PN102-TX, CNet Pro110B, 120A, and 120B, Compex RL100-TX,
1739# LinkSys LNE100TX, LNE100TX V2.0, Jaton XpressNet, Alfa Inc GFC2204,
1740# KNE110TX.
1741#
1742# The `de' device provides support for the Digital Equipment DC21040
1743# self-contained Ethernet adapter.
1744#
1745# The `em' device provides support for the Intel Pro/1000 Family of Gigabit
1746# adapters (82542, 82543, 82544, 82540).
1747#
d217d4d9
SZ
1748# The `et' device provides support for the Agere ET1310 10/100/1000 PCIe
1749# adapters.
1750#
984263bc
MD
1751# The `fxp' device provides support for the Intel EtherExpress Pro/100B
1752# PCI Fast Ethernet adapters.
1753#
1754# The `gx' device provides support for the Intel Pro/1000 Gigabit Ethernet
1755# PCI adapters (82542, 82543-F, 82543-T).
1756#
1757# The 'lge' device provides support for PCI gigabit ethernet adapters
1758# based on the Level 1 LXT1001 NetCellerator chipset. This includes the
1759# D-Link DGE-500SX, SMC TigerCard 1000 (SMC9462SX), and some Addtron cards.
1760#
1761# The 'my' device provides support for the Myson MTD80X and MTD89X PCI
1762# Fast Ethernet adapters.
1763#
1764# The 'nge' device provides support for PCI gigabit ethernet adapters
1765# based on the National Semiconductor DP83820 and DP83821 chipset. This
1766# includes the SMC EZ Card 1000 (SMC9462TX), D-Link DGE-500T, Asante
1767# FriendlyNet GigaNIX 1000TA and 1000TPC, the Addtron AEG320T, the
1768# LinkSys EG1032 and EG1064, the Surecom EP-320G-TX and the Netgear GA622T.
1769#
1770# The 'pcn' device provides support for PCI fast ethernet adapters based
1771# on the AMD Am79c97x chipsets, including the PCnet/FAST, PCnet/FAST+,
1772# PCnet/PRO and PCnet/Home. These were previously handled by the lnc
1773# driver (and still will be if you leave this driver out of the kernel).
1774#
44ac28ea
JS
1775# Te 're' device provides support for PCI GigaBit ethernet adapters based
1776# on the RealTek 8169 chipset. It also supports the 8139C+ and is the
56be8454 1777# preferred driver for that chip.
44ac28ea 1778#
984263bc
MD
1779# The 'rl' device provides support for PCI fast ethernet adapters based
1780# on the RealTek 8129/8139 chipset. Note that the RealTek driver defaults
1781# to using programmed I/O to do register accesses because memory mapped
1782# mode seems to cause severe lockups on SMP hardware. This driver also
1783# supports the Accton EN1207D `Cheetah' adapter, which uses a chip called
1784# the MPX 5030/5038, which is either a RealTek in disguise or a RealTek
1785# workalike. Note that the D-Link DFE-530TX+ uses the RealTek chipset
1786# and is supported by this driver, not the 'vr' driver.
1787#
1788# The 'sf' device provides support for Adaptec Duralink PCI fast
1789# ethernet adapters based on the Adaptec AIC-6915 "starfire" controller.
1790# This includes dual and quad port cards, as well as one 100baseFX card.
1791# Most of these are 64-bit PCI devices, except for one single port
1792# card which is 32-bit.
1793#
1794# The 'ste' device provides support for adapters based on the Sundance
1795# Technologies ST201 PCI fast ethernet controller. This includes the
1796# D-Link DFE-550TX.
1797#
1798# The 'sis' device provides support for adapters based on the Silicon
1799# Integrated Systems SiS 900 and SiS 7016 PCI fast ethernet controller
1800# chips.
1801#
1802# The 'sk' device provides support for the SysKonnect SK-984x series
1803# PCI gigabit ethernet NICs. This includes the SK-9841 and SK-9842
1804# single port cards (single mode and multimode fiber) and the
1805# SK-9843 and SK-9844 dual port cards (also single mode and multimode).
1806# The driver will autodetect the number of ports on the card and
1807# attach each one as a separate network interface.
1808#
1809# The 'ti' device provides support for PCI gigabit ethernet NICs based
1810# on the Alteon Networks Tigon 1 and Tigon 2 chipsets. This includes the
1811# Alteon AceNIC, the 3Com 3c985, the Netgear GA620 and various others.
1812# Note that you will probably want to bump up NMBCLUSTERS a lot to use
1813# this driver.
1814#
1815# The 'tl' device provides support for the Texas Instruments TNETE100
1816# series 'ThunderLAN' cards and integrated ethernet controllers. This
1817# includes several Compaq Netelligent 10/100 cards and the built-in
1818# ethernet controllers in several Compaq Prosignia, Proliant and
1819# Deskpro systems. It also supports several Olicom 10Mbps and 10/100
1820# boards.
1821#
1822# The `tx' device provides support for the SMC 9432 TX, BTX and FTX cards.
1823#
1824# The `txp' device provides support for the 3Com 3cR990 "Typhoon"
1825# 10/100 adapters.
1826#
1827# The `vr' device provides support for various fast ethernet adapters
1828# based on the VIA Technologies VT3043 `Rhine I' and VT86C100A `Rhine II'
1829# chips, including the D-Link DFE530TX (see 'rl' for DFE530TX+), the Hawking
1830# Technologies PN102TX, and the AOpen/Acer ALN-320.
1831#
1832# The `vx' device provides support for the 3Com 3C590 and 3C595
1833# early support
1834#
1835# The `wb' device provides support for various fast ethernet adapters
1836# based on the Winbond W89C840F chip. Note: this is not the same as
1837# the Winbond W89C940F, which is an NE2000 clone.
1838#
984263bc
MD
1839# The `xl' device provides support for the 3Com 3c900, 3c905 and
1840# 3c905B (Fast) Etherlink XL cards and integrated controllers. This
1841# includes the integrated 3c905B-TX chips in certain Dell Optiplex and
1842# Dell Precision desktop machines and the integrated 3c905-TX chips
1843# in Dell Latitude laptop docking stations.
1844#
984263bc
MD
1845# The `meteor' device is a PCI video capture board. It can also have the
1846# following options:
1847# options METEOR_ALLOC_PAGES=xxx preallocate kernel pages for data entry
1848# figure (ROWS*COLUMN*BYTES_PER_PIXEL*FRAME+PAGE_SIZE-1)/PAGE_SIZE
1849# options METEOR_DEALLOC_PAGES remove all allocated pages on close(2)
1850# options METEOR_DEALLOC_ABOVE=xxx remove all allocated pages above the
1851# specified amount. If this value is below the allocated amount no action
1852# taken
1853# options METEOR_SYSTEM_DEFAULT={METEOR_PAL|METEOR_NTSC|METEOR_SECAM}, used
1854# for initialization of fps routine when a signal is not present.
1855#
1856# The 'bktr' device is a PCI video capture device using the Brooktree
1857# bt848/bt848a/bt849a/bt878/bt879 chipset. When used with a TV Tuner it forms a
1858# TV card, eg Miro PC/TV, Hauppauge WinCast/TV WinTV, VideoLogic Captivator,
1859# Intel Smart Video III, AverMedia, IMS Turbo, FlyVideo.
1860#
1861# options OVERRIDE_CARD=xxx
1862# options OVERRIDE_TUNER=xxx
1863# options OVERRIDE_MSP=1
1864# options OVERRIDE_DBX=1
1865# These options can be used to override the auto detection
1866# The current values for xxx are found in src/sys/dev/bktr/bktr_card.h
1867# Using sysctl(8) run-time overrides on a per-card basis can be made
1868#
4ad6607f 1869# options BKTR_SYSTEM_DEFAULT=BROOKTREE_PAL
984263bc 1870# or
4ad6607f 1871# options BKTR_SYSTEM_DEFAULT=BROOKTREE_NTSC
984263bc
MD
1872# Specifes the default video capture mode.
1873# This is required for Dual Crystal (28&35Mhz) boards where PAL is used
1874# to prevent hangs during initialisation. eg VideoLogic Captivator PCI.
1875#
1876# options BKTR_USE_PLL
1877# PAL or SECAM users who have a 28Mhz crystal (and no 35Mhz crystal)
1878# must enable PLL mode with this option. eg some new Bt878 cards.
1879#
1880# options BKTR_GPIO_ACCESS
1881# This enable IOCTLs which give user level access to the GPIO port.
1882#
1883# options BKTR_NO_MSP_RESET
1884# Prevents the MSP34xx reset. Good if you initialise the MSP in another OS first
1885#
1886# options BKTR_430_FX_MODE
1887# Switch Bt878/879 cards into Intel 430FX chipset compatibility mode.
1888#
1889# options BKTR_SIS_VIA_MODE
1890# Switch Bt878/879 cards into SIS/VIA chipset compatibility mode which is
1891# needed for some old SiS and VIA chipset motherboards.
1892# This also allows Bt878/879 chips to work on old OPTi (<1997) chipset
1893# motherboards and motherboards with bad or incomplete PCI 2.1 support.
1894# As a rough guess, old = before 1998
1895#
a35cc233
JS
1896# options BKTR_NEW_MSP34XX_DRIVER
1897# Use new, more complete initialization scheme for the msp34* soundchip.
1898# Should fix stereo autodetection if the old driver does only output
1899# mono sound.
1900#
4ad6607f
SW
1901# options BKTR_OVERRIDE_CARD=xxx
1902# options BKTR_OVERRIDE_DBX=xxx
1903# options BKTR_OVERRIDE_MSP=xxx
1904# options BKTR_OVERRIDE_TUNER=xxx
1905# These options can be used to select a specific device, regardless of
1906# the autodetection and i2c device checks (see comments in bktr_card.c).
1907#
984263bc
MD
1908device ahc # AHA2940 and onboard AIC7xxx devices
1909device ahd # AIC79xx devices
1910device amd # AMD 53C974 (Tekram DC-390(T))
1911device isp # Qlogic family
1912device ispfw # Firmware for QLogic HBAs
07ee0d26 1913device mpt # LSI '909 FC adapters
984263bc
MD
1914device ncr # NCR/Symbios Logic
1915device sym # NCR/Symbios Logic (newer chipsets)
1916device trm # Tekram DC395U/UW/F and DC315U
1917#
1918# Options for ISP
1919#
1920# ISP_TARGET_MODE - enable target mode operation
1921#options ISP_TARGET_MODE=1
1922
1923# Options used in dev/sym/ (Symbios SCSI driver).
1924#options SYM_SETUP_LP_PROBE_MAP #-Low Priority Probe Map (bits)
1925 # Allows the ncr to take precedence
1926 # 1 (1<<0) -> 810a, 860
1927 # 2 (1<<1) -> 825a, 875, 885, 895
1928 # 4 (1<<2) -> 895a, 896, 1510d
1929#options SYM_SETUP_SCSI_DIFF #-HVD support for 825a, 875, 885
1930 # disabled:0 (default), enabled:1
1931#options SYM_SETUP_PCI_PARITY #-PCI parity checking
1932 # disabled:0, enabled:1 (default)
1933#options SYM_SETUP_MAX_LUN #-Number of LUNs supported
1934 # default:8, range:[1..64]
1935
1936
1937# MII bus support is required for some PCI 10/100 ethernet NICs,
1938# namely those which use MII-compliant transceivers or implement
3f625015 1939# transceiver control interfaces that operate like an MII. Adding
984263bc
MD
1940# "device miibus0" to the kernel config pulls in support for
1941# the generic miibus API and all of the PHY drivers, including a
1942# generic one for PHYs that aren't specifically handled by an
1943# individual driver.
1944device miibus
1945
1946# PCI Ethernet NICs that use the common MII bus controller code.
43c2aeb0 1947device bce # Broadcom NetXtreme II Gigabit Ethernet
7f186839 1948device bfe # Broadcom BCM440x 10/100 Ethernet
984263bc
MD
1949device dc # DEC/Intel 21143 and various workalikes
1950device fxp # Intel EtherExpress PRO/100B (82557, 82558)
1951device my # Myson Fast Ethernet (MTD80X, MTD89X)
1952device pcn # AMD Am79C97x PCI 10/100 NICs
44ac28ea 1953device re # RealTek 8139C+/8169
984263bc
MD
1954device rl # RealTek 8129/8139
1955device sbsh # Granch SBNI16 SHDSL modem
1956device sf # Adaptec AIC-6915 (``Starfire'')
1957device sis # Silicon Integrated Systems SiS 900/SiS 7016
1958device ste # Sundance ST201 (D-Link DFE-550TX)
1959device tl # Texas Instruments ThunderLAN
1960device tx # SMC EtherPower II (83c17x ``EPIC'')
13bca4c6 1961device vge # VIA 612x GigE
984263bc
MD
1962device vr # VIA Rhine, Rhine II
1963device wb # Winbond W89C840F
1964device xl # 3Com 3c90x (``Boomerang'', ``Cyclone'')
1965
1966# PCI Ethernet NICs.
1967device de # DEC/Intel DC21x4x (``Tulip'')
1968device txp # 3Com 3cR990 (``Typhoon'')
1969device vx # 3Com 3c590, 3c595 (``Vortex'')
1970
1971# Gigabit Ethernet NICs.
1972device bge # Broadcom BCM570x (``Tigon III'')
1973device em # Intel Pro/1000 (82542,82543,82544,82540)
d217d4d9 1974device et # Agere ET1310 10/100/1000 Ethernet
984263bc
MD
1975device gx # Intel Pro/1000 (82542, 82543)
1976device lge # Level 1 LXT1001 (``Mercury'')
ffb8a862 1977device nfe # nVidia nForce2/3 MCP04/51/55 CK804
984263bc 1978device nge # NatSemi DP83820 and DP83821
0db5ca13 1979device sk # SysKonnect GEnesis, LinkSys EG1023, D-Link
984263bc 1980device ti # Alteon (``Tigon I'', ``Tigon II'')
1da2c9db 1981device stge # Sundance/Tamarack TC9021 Gigabit Ethernet
984263bc 1982
984263bc 1983device meteor
984263bc
MD
1984
1985
1986# Brooktree driver has been ported to the new I2C framework. Thus,
1987# you'll need to have the following 3 lines in the kernel config.
1988# device smbus
1989# device iicbus
1990# device iicbb
1991# The iic and smb devices are only needed if you want to control other
1992# I2C slaves connected to the external connector of some cards.
1993#
1994device bktr
a35cc233 1995options BKTR_NEW_MSP34XX_DRIVER
984263bc
MD
1996
1997#
1998# PCCARD/PCMCIA
1999#
666d2603 2000# pccard: pccard slots
6f535fd5 2001# cardbus/cbb: cardbus bridge
666d2603
JS
2002device pccard
2003device cardbus
2004device cbb
984263bc
MD
2005
2006#
2007# Laptop/Notebook options:
2008#
2009# See also:
2010# apm under `Miscellaneous hardware'
2011# above.
2012
2013# For older notebooks that signal a powerfail condition (external
2014# power supply dropped, or battery state low) by issuing an NMI:
2015
2016options POWERFAIL_NMI # make it beep instead of panicing
2017
2018#
2019# SMB bus
2020#
2021# System Management Bus support is provided by the 'smbus' device.
2022# Access to the SMBus device is via the 'smb' device (/dev/smb*),
2023# which is a child of the 'smbus' device.
2024#
2025# Supported devices:
2026# smb standard io through /dev/smb*
2027#
2028# Supported SMB interfaces:
2029# iicsmb I2C to SMB bridge with any iicbus interface
2030# bktr brooktree848 I2C hardware interface
2031# intpm Intel PIIX4 (82371AB, 82443MX) Power Management Unit
2032# alpm Acer Aladdin-IV/V/Pro2 Power Management Unit
2033# ichsmb Intel ICH SMBus controller chips (82801AA, 82801AB, 82801BA)
2034# viapm VIA VT82C586B,596,686A and VT8233 SMBus controllers
2035# amdpm AMD 756 Power Management Unit
2036#
2037device smbus # Bus support, required for smb below.
2038
2039device intpm
2040device alpm
2041device ichsmb
2042device viapm
2043device amdpm
2044
2045device smb
2046
2047#
2048# I2C Bus
2049#
2050# Philips i2c bus support is provided by the `iicbus' device.
2051#
2052# Supported devices:
2053# ic i2c network interface
2054# iic i2c standard io
2055# iicsmb i2c to smb bridge. Allow i2c i/o with smb commands.
2056#
2057# Supported interfaces:
2058# pcf Philips PCF8584 ISA-bus controller
2059# bktr brooktree848 I2C software interface
2060#
2061# Other:
2062# iicbb generic I2C bit-banging code (needed by lpbb, bktr)
2063#
2064device iicbus # Bus support, required for ic/iic/iicsmb below.
2065device iicbb
2066
2067device ic
2068device iic
2069device iicsmb # smb over i2c bridge
2070
2071device pcf0 at isa? port 0x320 irq 5
2072
3a514b87
HT
2073# Intel Core and newer CPUs on-die digital thermal sensor support
2074device coretemp
2075
1d03db02
HT
2076# HW monitoring devices lm(4) and it(4).
2077device lm0 at isa? port 0x290
2078device it0 at isa? port 0x290
2079device it1 at isa? port 0xc00
2080device it2 at isa? port 0xd00
2081
984263bc
MD
2082#---------------------------------------------------------------------------
2083# ISDN4BSD
2084#
2085# See /usr/share/examples/isdn/ROADMAP for an introduction to isdn4bsd.
2086#
2087# i4b passive ISDN cards support contains the following hardware drivers:
2088#
2089# isic - Siemens/Infineon ISDN ISAC/HSCX/IPAC chipset driver
2090# iwic - Winbond W6692 PCI bus ISDN S/T interface controller
2091# ifpi - AVM Fritz!Card PCI driver
2092# ifpi2 - AVM Fritz!Card PCI driver Version 2
2093# ihfc - Cologne Chip HFC ISA/ISA-PnP chipset driver
2094# ifpnp - AVM Fritz!Card PnP driver
2095# itjc - Siemens ISAC / TJNet Tiger300/320 chipset
2096#
2097# i4b active ISDN cards support contains the following hardware drivers:
2098#
2099# iavc - AVM B1 PCI, AVM B1 ISA, AVM T1
2100#
2101# Note that the ``options'' (if given) and ``device'' lines must BOTH
2102# be uncommented to enable support for a given card !
2103#
2104# In addition to a hardware driver (and probably an option) the mandatory
2105# ISDN protocol stack devices and the mandatory support device must be
2106# enabled as well as one or more devices from the optional devices section.
2107#
2108#---------------------------------------------------------------------------
2109# isic driver (Siemens/Infineon chipsets)
2110#---------------------------------------------------------------------------
2111#
2112# ISA bus non-PnP Cards:
2113# ----------------------
2114#
2115# Teles S0/8 or Niccy 1008
2116options TEL_S0_8
2117device isic0 at isa? iomem 0xd0000 irq 5 flags 1
2118#
2119# Teles S0/16 or Creatix ISDN-S0 or Niccy 1016
2120options TEL_S0_16
2121#device isic0 at isa? port 0xd80 iomem 0xd0000 irq 5 flags 2
2122#
2123# Teles S0/16.3
2124options TEL_S0_16_3
2125#device isic0 at isa? port 0xd80 irq 5 flags 3
2126#
2127# AVM A1 or AVM Fritz!Card
2128options AVM_A1
2129#device isic0 at isa? port 0x340 irq 5 flags 4
2130#
2131# USRobotics Sportster ISDN TA intern
2132options USR_STI
2133#device isic0 at isa? port 0x268 irq 5 flags 7
2134#
2135# ITK ix1 Micro ( < V.3, non-PnP version )
2136options ITKIX1
2137#device isic0 at isa? port 0x398 irq 10 flags 18
2138#
2139# ELSA PCC-16
2140options ELSA_PCC16
2141#device isic0 at isa? port 0x360 irq 10 flags 20
2142#
2143# ISA bus PnP Cards:
2144# ------------------
2145#
2146# Teles S0/16.3 PnP
2147options TEL_S0_16_3_P
2148#device isic
2149#
2150# Creatix ISDN-S0 P&P
2151options CRTX_S0_P
2152#device isic
2153#
2154# Dr. Neuhaus Niccy Go@
2155options DRN_NGO
2156#device isic
2157#
2158# Sedlbauer Win Speed
2159options SEDLBAUER
2160#device isic
2161#
2162# Dynalink IS64PH
2163options DYNALINK
2164#device isic
2165#
2166# ELSA QuickStep 1000pro ISA
2167options ELSA_QS1ISA
2168#device isic
2169#
2170# ITK ix1 Micro ( V.3, PnP version )
2171options ITKIX1
2172#device isic
2173#
2174# Siemens I-Surf 2.0
2175options SIEMENS_ISURF2
2176#device isic
2177#
2178# Asuscom ISDNlink 128K ISAC
2179options ASUSCOM_IPAC
2180#device isic
2181#
2182# Eicon Diehl DIVA 2.0 and 2.02
2183options EICON_DIVA
2184#device isic
2185#
4ad6607f
SW
2186# Compaq Microcom 610
2187options COMPAQ_M610
2188#device isic
2189#
984263bc
MD
2190# PCI bus Cards:
2191# --------------
2192#
2193# ELSA MicroLink ISDN/PCI (same as ELSA QuickStep 1000pro PCI)
2194options ELSA_QS1PCI
2195#device isic
2196#
2197#---------------------------------------------------------------------------
2198# ifpnp driver for AVM Fritz!Card ISA PnP
2199#---------------------------------------------------------------------------
2200#
2201# AVM Fritz!Card ISA PnP
2202device ifpnp
2203#
2204#---------------------------------------------------------------------------
2205# ihfc driver for Cologne Chip ISA chipsets (experimental!)
2206#---------------------------------------------------------------------------
2207#
2208# Teles 16.3c ISA PnP
2209# AcerISDN P10 ISA PnP
2210# TELEINT ISDN SPEED No.1
2211device ihfc
2212#
2213#---------------------------------------------------------------------------
2214# ifpi driver for AVM Fritz!Card PCI 1.0 (2.0 unsupported!)
2215#---------------------------------------------------------------------------
2216#
2217# AVM Fritz!Card PCI 1.0
2218device ifpi
2219#
2220#---------------------------------------------------------------------------
2221# ifpi2 driver for AVM Fritz!Card PCI 2.0
2222#---------------------------------------------------------------------------
2223#
2224# AVM Fritz!Card PCI 2.0
2225device "ifpi2"
2226#
2227#---------------------------------------------------------------------------
2228# iwic driver for Winbond W6692 chipset
2229#---------------------------------------------------------------------------
2230#
2231# ASUSCOM P-IN100-ST-D (and other Winbond W6692 based cards)
2232device iwic
2233#
2234#---------------------------------------------------------------------------
3f625015 2235# itjc driver for Siemens ISAC / TJNet Tiger300/320 chipset
984263bc
MD
2236#---------------------------------------------------------------------------
2237#
2238# Traverse Technologies NETjet-S
2239# Teles PCI-TJ
2240device itjc
2241#
2242#---------------------------------------------------------------------------
2243# iavc driver (AVM active cards, needs i4bcapi driver!)
2244#---------------------------------------------------------------------------
2245#
2246pseudo-device "i4bcapi" 2
2247#
2248# AVM B1 PCI
2249device iavc0
2250#
2251# AVM B1 ISA bus (PnP mode not supported!)
2252#device iavc0 at isa? port 0x150 irq 5
2253#
2254#
2255# ISDN Protocol Stack (mandatory)
2256# -------------------------------
2257#
2258# Q.921 / layer 2 - i4b passive cards D channel handling
2259pseudo-device "i4bq921"
2260#
2261# Q.931 / layer 3 - i4b passive cards D channel handling
2262pseudo-device "i4bq931"
2263#
2264# layer 4 - i4b common passive and active card handling
2265pseudo-device "i4b"
2266#
2267# ISDN devices
2268# ------------
2269#
2270# userland driver to do ISDN tracing (for passive cards only)
2271pseudo-device "i4btrc" 4
2272#
2273# userland driver to control the whole thing (mandatory)
2274pseudo-device "i4bctl"
2275#
2276# userland driver for access to raw B channel
2277pseudo-device "i4brbch" 4
2278#
2279# userland driver for telephony
2280pseudo-device "i4btel" 2
2281#
2282# network driver for IP over raw HDLC ISDN
2283pseudo-device "i4bipr" 4
2284# enable VJ header compression detection for ipr i/f
2285options IPR_VJ
2286# enable logging of the first n IP packets to isdnd (n=32 here)
2287#options IPR_LOG=32
2288#
2289# network driver for sync PPP over ISDN - requires sppp
2290pseudo-device "i4bisppp" 4
2291
2292
2293# Parallel-Port Bus
2294#
2295# Parallel port bus support is provided by the `ppbus' device.
2296# Multiple devices may be attached to the parallel port, devices
2297# are automatically probed and attached when found.
2298#
2299# Supported devices:
2300# vpo Iomega Zip Drive
2301# Requires SCSI disk support ('scbus' and 'da'); the best
2302# performance is achieved with ports in EPP 1.9 mode.
2303# lpt Parallel Printer
2304# plip Parallel network interface
2305# ppi General-purpose I/O ("Geek Port") + IEEE1284 I/O
2306# pps Pulse per second Timing Interface
2307# lpbb Philips official parallel port I2C bit-banging interface
2308#
2309# Supported interfaces:
2310# ppc ISA-bus parallel port interfaces.
2311#
2312
2313options PPC_PROBE_CHIPSET # Enable chipset specific detection
2314 # (see flags in ppc(4))
2315options DEBUG_1284 # IEEE1284 signaling protocol debug
2316options PERIPH_1284 # Makes your computer act as a IEEE1284
2317 # compliant peripheral
2318options DONTPROBE_1284 # Avoid boot detection of PnP parallel devices
2319options VP0_DEBUG # ZIP/ZIP+ debug
2320options LPT_DEBUG # Printer driver debug
969dee2c 2321options PPC_DEBUG=2 # Parallel chipset level debug
984263bc
MD
2322options PLIP_DEBUG # Parallel network IP interface debug
2323options PCFCLOCK_VERBOSE # Verbose pcfclock driver
2324options PCFCLOCK_MAX_RETRIES=5 # Maximum read tries (default 10)
2325
2326device ppc0 at isa? irq 7
2327device ppbus
2328device vpo
2329device lpt
2330device plip
2331device ppi
2332device pps
2333device lpbb
2334device pcfclock
2335
2336# Kernel BOOTP support
2337
2338options BOOTP # Use BOOTP to obtain IP address/hostname
2339options BOOTP_NFSROOT # NFS mount root filesystem using BOOTP info
2340options BOOTP_NFSV3 # Use NFS v3 to NFS mount root
2341options BOOTP_COMPAT # Workaround for broken bootp daemons.
2342options BOOTP_WIRED_TO=fxp0 # Use interface fxp0 for BOOTP
2343
2344#
2345# Add tie-ins for a hardware watchdog. This only enable the hooks;
2346# the user must still supply the actual driver.
2347#
2348options HW_WDOG
2349
2350#
2351# Set the number of PV entries per process. Increasing this can
2352# stop panics related to heavy use of shared memory. However, that can
2353# (combined with large amounts of physical memory) cause panics at
2354# boot time due the kernel running out of VM space.
2355#
2356# If you're tweaking this, you might also want to increase the sysctls
2357# "vm.v_free_min", "vm.v_free_reserved", and "vm.v_free_target".
2358#
2359# The value below is the one more than the default.
2360#
2361options PMAP_SHPGPERPROC=201
2362
2363#
2364# Change the size of the kernel virtual address space. Due to
2365# constraints in loader(8) on i386, this must be a multiple of 4.
2366# 256 = 1 GB of kernel address space. Increasing this also causes
2367# a reduction of the address space in user processes. 512 splits
2368# the 4GB cpu address space in half (2GB user, 2GB kernel).
2369#
2370options KVA_PAGES=260
2371
2372#
2373# Disable swapping. This option removes all code which actually performs
2374# swapping, so it's not possible to turn it back on at run-time.
2375#
2376# This is sometimes usable for systems which don't have any swap space
2377# (see also sysctls "vm.defer_swapspace_pageouts" and
2378# "vm.disable_swapspace_pageouts")
2379#
2380#options NO_SWAPPING
2381
2382# Set the number of sf_bufs to allocate. sf_bufs are virtual buffers
2383# for sendfile(2) that are used to map file VM pages, and normally
2384# default to a quantity that is roughly 16*MAXUSERS+512. You would
2385# typically want about 4 of these for each simultaneous file send.
2386#
2387options NSFBUFS=1024
2388
2389# Set the size of the buffer cache KVM reservation, in buffers. This is
2390# scaled by approximately 16384 bytes. The system will auto-size the buffer
2391# cache if this option is not specified.
2392#
2393options NBUF=512
2394
2395# Set the size of the mbuf KVM reservation, in clusters. This is scaled
2396# by approximately 2048 bytes. The system will auto-size the mbuf area
2397# to (512 + maxusers*16) if this option is not specified.
2398# maxusers is in turn computed at boot time depending on available memory
2399# or set to the value specified by "options MAXUSERS=x" (x=0 means
2400# autoscaling).
2401# So, to take advantage of autoscaling, you have to remove both
2402# NMBCLUSTERS and MAXUSERS (and NMBUFS) from your kernel config.
2403#
2404options NMBCLUSTERS=1024
2405
2406# Set the number of mbufs available in the system. Each mbuf
2407# consumes 256 bytes. The system will autosize this (to 4 times
2408# the number of NMBCLUSTERS, depending on other constraints)
2409# if this option is not specified.
2410#
2411options NMBUFS=4096
2412
984263bc
MD
2413# Tune the buffer cache maximum KVA reservation, in bytes. The maximum is
2414# usually capped at 200 MB, effecting machines with > 1GB of ram. Note
2415# that the buffer cache only really governs write buffering and disk block
2416# translations. The VM page cache is our primary disk cache and is not
2417# effected by the size of the buffer cache.
2418#
2419options VM_BCACHE_SIZE_MAX="(100*1024*1024)"
2420
2421# Tune the swap zone KVA reservation, in bytes. The default is typically
2422# 70 MB, giving the system the ability to manage a maximum of 28GB worth
2423# of swapped out data.
2424#
2425options VM_SWZONE_SIZE_MAX="(50*1024*1024)"
2426
2427#
2428# Enable extra debugging code for locks. This stores the filename and
2429# line of whatever acquired the lock in the lock itself, and change a
2430# number of function calls to pass around the relevant data. This is
2431# not at all useful unless you are debugging lock code. Also note
2432# that it is likely to break e.g. fstat(1) unless you recompile your
2433# userland with -DDEBUG_LOCKS as well.
2434#
2435options DEBUG_LOCKS
2436
2437# Set the amount of time (in seconds) the system will wait before
2438# rebooting automatically when a kernel panic occurs. If set to (-1),
2439# the system will wait indefinitely until a key is pressed on the
2440# console.
2441options PANIC_REBOOT_WAIT_TIME=16
2442
2443# Attempt to bypass the buffer cache and put data directly into the
2444# userland buffer for read operation when O_DIRECT flag is set on the
2445# file. Both offset and length of the read operation must be
2446# multiples of the physical media sector size.
2447#
1ff70875 2448options DIRECTIO
984263bc
MD
2449
2450# Specify a lower limit for the number of swap I/O buffers. They are
2451# (among other things) used when bypassing the buffer cache due to
2452# DIRECTIO kernel option enabled and O_DIRECT flag set on file.
2453#
2454#options NSWBUF_MIN=120
2455
984263bc
MD
2456# The 'asr' driver provides support for current DPT/Adaptec SCSI RAID
2457# controllers (SmartRAID V and VI and later).
2458# These controllers require the CAM infrastructure.
2459#
2460device asr
2461
2462# The 'dpt' driver provides support for DPT controllers (http://www.dpt.com/).
2463# These have hardware RAID-{0,1,5} support, and do multi-initiator I/O.
2464# The DPT controllers are commonly re-licensed under other brand-names -
2465# some controllers by Olivetti, Dec, HP, AT&T, SNI, AST, Alphatronic, NEC and
2466# Compaq are actually DPT controllers.
2467#
2468# See src/sys/dev/dpt for debugging and other subtle options.
2469# DPT_MEASURE_PERFORMANCE Enables a set of (semi)invasive metrics. Various
2470# instruments are enabled. The tools in
2471# /usr/sbin/dpt_* assume these to be enabled.
2472# DPT_HANDLE_TIMEOUTS Normally device timeouts are handled by the DPT.
2473# If you ant the driver to handle timeouts, enable
2474# this option. If your system is very busy, this
2475# option will create more trouble than solve.
2476# DPT_TIMEOUT_FACTOR Used to compute the excessive amount of time to
2477# wait when timing out with the above option.
2478# DPT_DEBUG_xxxx These are controllable from sys/dev/dpt/dpt.h
2479# DPT_LOST_IRQ When enabled, will try, once per second, to catch
2480# any interrupt that got lost. Seems to help in some
2481# DPT-firmware/Motherboard combinations. Minimal
2482# cost, great benefit.
2483# DPT_RESET_HBA Make "reset" actually reset the controller
2484# instead of fudging it. Only enable this if you
2485# are 100% certain you need it.
2486
2487device dpt
2488
2489# DPT options
2490#!CAM# options DPT_MEASURE_PERFORMANCE
2491#!CAM# options DPT_HANDLE_TIMEOUTS
2492options DPT_TIMEOUT_FACTOR=4
2493options DPT_LOST_IRQ
2494options DPT_RESET_HBA
984263bc
MD
2495
2496#
2497# Compaq "CISS" RAID controllers (SmartRAID 5* series)
2498# These controllers have a SCSI-like interface, and require the
2499# CAM infrastructure.
2500#
2501device ciss
2502
2503#
2504# Intel Integrated RAID controllers.
2505# This driver was developed and is maintained by Intel. Contacts
2506# at Intel for this driver are
2507# "Kannanthanam, Boji T" <boji.t.kannanthanam@intel.com> and
2508# "Leubner, Achim" <achim.leubner@intel.com>.
2509#
2510device iir
2511
2512#
2513# Mylex AcceleRAID and eXtremeRAID controllers with v6 and later
2514# firmware. These controllers have a SCSI-like interface, and require
2515# the CAM infrastructure.
2516#
2517device mly
2518
2519# USB support
2520# UHCI controller
2521device uhci
2522# OHCI controller
2523device ohci
dc1d8198
JR
2524# EHCI controller
2525device ehci
984263bc
MD
2526# General USB code (mandatory for USB)
2527device usb
2528#
2529# Fm Radio
2530device ufm
2531# Generic USB device driver
2532device ugen
2533# Human Interface Device (anything with buttons and dials)
2534device uhid
2535# USB keyboard
2536device ukbd
2537# USB printer
2538device ulpt
2539# USB Iomega Zip 100 Drive (Requires scbus and da)
2540device umass
2541# USB modem support
2542device umodem
2543# USB mouse
2544device ums
2545# USB Rio (MP3 Player)
2546device urio
2547# USB scanners
2548device uscanner
2549# USB com devices
bfe2a61e 2550device moscom
474e48cc
HT
2551device uark
2552device ubsa
c2318dc6 2553device uchcom
984263bc 2554device ucom
474e48cc 2555device uftdi
3ff11514 2556device umct
474e48cc 2557device umsm
984263bc 2558device uplcom
5926abe5 2559device uslcom
474e48cc 2560device uticom
984263bc 2561device uvisor
474e48cc 2562device uvscom
984263bc
MD
2563
2564#
2565# ADMtek USB ethernet. Supports the LinkSys USB100TX,
2566# the Billionton USB100, the Melco LU-ATX, the D-Link DSB-650TX
2567# and the SMC 2202USB. Also works with the ADMtek AN986 Pegasus
2568# eval board.
2569device aue
2570#
204496c7
SW
2571# ASIX Electronics AX88172 USB 2.0 ethernet driver. Used in the
2572# LinkSys USB200M and various other adapters.
2573device axe
2574#
984263bc
MD
2575# CATC USB-EL1201A USB ethernet. Supports the CATC Netmate
2576# and Netmate II, and the Belkin F5U111.
2577device cue
2578#
2579# Kawasaki LSI ethernet. Supports the LinkSys USB10T,
2580# Entrega USB-NET-E45, Peracom Ethernet Adapter, the
2581# 3Com 3c19250, the ADS Technologies USB-10BT, the ATen UC10T,
2582# the Netgear EA101, the D-Link DSB-650, the SMC 2102USB
2583# and 2104USB, and the Corega USB-T.
2584device kue
3c374c15
SZ
2585#
2586# RealTek 8150 based USB ethernet device:
2587# Melco LUA-KTX
2588# GREEN HOUSE GH-USB100B
2589# Billionton ThumbLAN USBKR2-100B
2590device rue
984263bc 2591
428b19ed
SZ
2592# USB wireless NICs, requires wlan_ratectl_onoe
2593#
2594# Ralink Technology RT2501USB/RT2601USB
2595device rum
2596#
2597# Ralink Technology RT2500USB
2598device ural
2599
984263bc
MD
2600# debugging options for the USB subsystem
2601#
2602options USB_DEBUG
2603
2604# options for ukbd:
2605options UKBD_DFLT_KEYMAP # specify the built-in keymap
2606makeoptions UKBD_DFLT_KEYMAP=it.iso
2607
2608# Firewire support
2609device firewire # Firewire bus code
2610device sbp # SCSI over Firewire (Requires scbus and da)
2611device fwe # Ethernet over Firewire (non-standard!)
2612
ca9d2ae7
HS
2613# dcons support (Dumb Console Device)
2614device dcons # dumb console driver
2615device dcons_crom # FireWire attachment
2616options DCONS_BUF_SIZE=16384 # buffer size
2617options DCONS_POLL_HZ=100 # polling rate
2618options DCONS_FORCE_CONSOLE=1 # force to be the primary console
2619options DCONS_FORCE_GDB=1 # force to be the gdb device
2620
984263bc
MD
2621#####################################################################
2622# crypto subsystem
2623#
2624# This is a port of the openbsd crypto framework. Include this when
2625# configuring IPsec and when you have a h/w crypto device to accelerate
2626# user applications that link to openssl.
2627#
2628# Drivers are ports from openbsd with some simple enhancements that have
2629# been fed back to openbsd (and hopefully will be included).
2630
2631pseudo-device crypto # core crypto support
2632pseudo-device cryptodev # /dev/crypto for access to h/w
2633
2634device rndtest # FIPS 140-2 entropy tester
2635
2636device hifn # Hifn 7951, 7781, etc.
2637options HIFN_DEBUG # enable debugging support: hw.hifn.debug
4ad6607f 2638#options HIFN_NO_RNG # for devices without RNG
984263bc
MD
2639options HIFN_RNDTEST # enable rndtest support
2640
2641device ubsec # Broadcom 5501, 5601, 58xx
2642options UBSEC_DEBUG # enable debugging support: hw.ubsec.debug
4ad6607f 2643#options UBSEC_NO_RNG # for devices without RNG
984263bc
MD
2644options UBSEC_RNDTEST # enable rndtest support
2645
c86cd76a 2646device acpi # basic ACPI support
3af1933a 2647device pmtimer # adjust the system clock after resume
a62a1fac 2648
984263bc
MD
2649# DRM options:
2650# mgadrm: AGP Matrox G200, G400, G450, G550
2651# tdfxdrm: 3dfx Voodoo 3/4/5 and Banshee
2652# r128drm: ATI Rage 128
2653# radeondrm: ATI Radeon up to 9000/9100
2654# DRM_DEBUG: include debug printfs, very slow
2655#
2656# mga requires AGP in the kernel, and it is recommended
2657# for AGP r128 and radeon cards.
2658
2659device mgadrm
2660device "r128drm"
2661device radeondrm
2662device tdfxdrm
2663
2664options DRM_DEBUG
4ad6607f 2665options DRM_LINUX
984263bc
MD
2666
2667#
2668# Embedded system options:
2669#
2670# An embedded system might want to run something other than init.
2671options INIT_PATH="/sbin/init:/stand/sysinstall"
2672
2673# Debug options
2674options BUS_DEBUG # enable newbus debugging
984263bc
MD
2675options NPX_DEBUG # enable npx debugging (FPU/math emu)
2676
8a4ec68a
SW
2677# Record the program counter of the code interrupted by the statistics
2678# clock interrupt. Use pctrack(8) to dump this information.
2679options DEBUG_PCTRACK
2680
984263bc
MD
2681# More undocumented options for linting.
2682# Note that documenting these are not considered an affront.
2683
4ad6607f
SW
2684options ACPI_DEBUG
2685#options ACPI_NO_SEMAPHORES
f7c1d76d 2686options ACPI_QUIRK_VMWARE
984263bc 2687options AHC_DUMP_EEPROM
4ad6607f 2688#options BKTR_ALLOC_PAGES=xxx
984263bc
MD
2689options CAM_DEBUG_DELAY
2690options CLUSTERDEBUG
2691options COMPAT_LINUX
4ad6607f 2692options COMPAT_SUNOS
984263bc 2693options DEBUG
4ad6607f
SW
2694options DEBUG_CRIT_SECTIONS
2695options DEBUG_INTERRUPTS
2696options DEVICE_SYSCTLS
984263bc 2697#options DISABLE_PSE
43c2aeb0
SZ
2698options BCE_DEBUG
2699options BCE_NVRAM_WRITE_SUPPORT
4ad6607f 2700#options ED_NO_MIIBUS
984263bc 2701options ENABLE_ALART
969dee2c 2702options FB_DEBUG=2
984263bc
MD
2703options FB_INSTALL_CDEV
2704options FE_8BIT_SUPPORT
2705options I4B_SMP_WORKAROUND
2706options I586_PMC_GUPROF=0x70000
969dee2c 2707options KBDIO_DEBUG=10
984263bc
MD
2708options KBD_MAXRETRY=4
2709options KBD_MAXWAIT=6
2710options KBD_RESETDELAY=201
4ad6607f 2711options KERN_TIMESTAMP
984263bc 2712options KEY
4ad6607f 2713options LINPROCFS
984263bc
MD
2714options LOCKF_DEBUG
2715options LOUTB
4ad6607f 2716#options MAXFILES=xxx
5054c0b0 2717options MBUF_DEBUG
4ad6607f 2718options METEOR_TEST_VIDEO
984263bc 2719options NETATALKDEBUG
4ad6607f 2720options PANIC_DEBUG
969dee2c 2721options PSM_DEBUG=4
984263bc
MD
2722options SCSI_NCR_DEBUG
2723options SCSI_NCR_MAX_SYNC=10000
2724options SCSI_NCR_MAX_WIDE=1
2725options SCSI_NCR_MYADDR=7
984263bc
MD
2726options SHOW_BUSYBUFS # List buffers that prevent root unmount
2727options SIMPLELOCK_DEBUG
2728options SI_DEBUG
2729options SLIP_IFF_OPTS
4ad6607f 2730options SOCKBUF_DEBUG
984263bc
MD
2731options TIMER_FREQ="((14318182+6)/12)"
2732options VFS_BIO_DEBUG
4ad6607f 2733options WI_SYMBOL_FIRMWARE
984263bc 2734options XBONEHACK
81540c2d
EN
2735
2736options KTR
edba61da
SW
2737#options KTR_GIANT_CONTENTION
2738#options KTR_SPIN_CONTENTION
4ad6607f
SW
2739#options KTR_IPIQ
2740#options KTR_MEMORY
2741#options KTR_TOKENS
2742#options KTR_USB_MEMORY
94c0a264
SZ
2743#options KTR_IF_EM
2744#options KTR_IF_BGE
d3776285 2745options KTR_ALL
81540c2d
EN
2746options KTR_ENTRIES=1024
2747options KTR_VERBOSE=1
4d723e5a
JS
2748
2749# ALTQ
2750options ALTQ #alternate queueing
2751options ALTQ_CBQ #class based queueing
2752options ALTQ_RED #random early detection
2753options ALTQ_RIO #triple red for diffserv (needs RED)
2754options ALTQ_HFSC #hierarchical fair service curve
2755options ALTQ_PRIQ #priority queue
2756#options ALTQ_NOPCC #don't use processor cycle counter
2757options ALTQ_DEBUG #for debugging
2758# you might want to set kernel timer to 1kHz if you use CBQ,
2759# especially with 100baseT
2760#options HZ=1000
5e937ff0
EN
2761
2762# SCTP
2763options SCTP
2764options SCTP_DEBUG
5e937ff0
EN
2765options SCTP_USE_ADLER32
2766options SCTP_HIGH_SPEED
2767options SCTP_STAT_LOGGING
2768options SCTP_CWND_LOGGING
2769options SCTP_BLK_LOGGING
2770options SCTP_STR_LOGGING
2771options SCTP_FR_LOGGING
2772options SCTP_MAP_LOGGING