ath - Fix a mismatch in the module options.
[dragonfly.git] / sys / dev / netif / ath / hal / Makefile
CommitLineData
193b341d 1#
3f720b20 2# Copyright (c) 2002-2008 Sam Leffler, Errno Consulting
193b341d
SZ
3# All rights reserved.
4#
5# Redistribution and use in source and binary forms, with or without
6# modification, are permitted provided that the following conditions
7# are met:
8# 1. Redistributions of source code must retain the above copyright
9# notice, this list of conditions and the following disclaimer,
10# without modification.
11# 2. Redistributions in binary form must reproduce at minimum a disclaimer
12# similar to the "NO WARRANTY" disclaimer below ("Disclaimer") and any
13# redistribution must be conditioned upon including a substantially
14# similar Disclaimer requirement for further binary redistribution.
193b341d
SZ
15#
16# NO WARRANTY
17# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
18# ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
19# LIMITED TO, THE IMPLIED WARRANTIES OF NONINFRINGEMENT, MERCHANTIBILITY
20# AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL
21# THE COPYRIGHT HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY,
22# OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
23# SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
24# INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER
25# IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
26# ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
27# THE POSSIBILITY OF SUCH DAMAGES.
28#
3f720b20 29# $FreeBSD: src/sys/modules/ath/Makefile,v 1.5.2.1.2.1 2009/04/15 03:14:26 kensmith Exp $
193b341d
SZ
30#
31
3f720b20
HT
32ATH_RATE?= sample # tx rate control algorithm
33
34HAL=${.CURDIR}/ath_hal
35.PATH: ${.CURDIR}
36.PATH: ${HAL}
37KMOD= ath_hal
38#SRCS= if_ath.c if_ath_pci.c
39#SRCS = ah_osdep.c
40#SRCS += bus_if.h device_if.h pci_if.h opt_ah.h
41# NB: v3 eeprom support used by both AR5211 and AR5212; just include it
42SRCS= ah_osdep.c ah_osdep.h ah.c ah_regdomain.c ah_eeprom_v3.c
43SRCS+= device_if.h bus_if.h pci_if.h opt_inet.h opt_ath.h opt_ah.h
44
193b341d 45#
3f720b20
HT
46# AR5210 support; these are first generation 11a-only devices.
47#
48.PATH: ${HAL}/ar5210
49.PATH: ${HAL}
50SRCS+= ah_eeprom_v1.c \
51 ar5210_attach.c ar5210_beacon.c ar5210_interrupts.c \
52 ar5210_keycache.c ar5210_misc.c ar5210_phy.c ar5210_power.c \
53 ar5210_recv.c ar5210_reset.c ar5210_xmit.c
54
193b341d 55#
3f720b20
HT
56# AR5211 support; these are second generation 11b/g/a devices
57# (but 11g was OFDM only and is not supported).
193b341d 58#
3f720b20
HT
59.PATH: ${HAL}/ar5211
60SRCS+= ar5211_attach.c ar5211_beacon.c ar5211_interrupts.c \
61 ar5211_keycache.c ar5211_misc.c ar5211_phy.c ar5211_power.c \
62 ar5211_recv.c ar5211_reset.c ar5211_xmit.c
193b341d 63
3f720b20
HT
64#
65# AR5212 support; this covers all other pci/cardbus legacy parts.
66#
67.PATH: ${HAL}/ar5212
68SRCS+= ar5212_ani.c ar5212_attach.c ar5212_beacon.c ar5212_eeprom.c \
69 ar5212_gpio.c ar5212_interrupts.c ar5212_keycache.c ar5212_misc.c \
70 ar5212_phy.c ar5212_power.c ar5212_recv.c ar5212_reset.c \
71 ar5212_rfgain.c ar5212_xmit.c
72# RF backends
73SRCS+= ar5111.c
74SRCS+= ar5112.c
75SRCS+= ar2413.c
76SRCS+= ar2425.c
77SRCS+= ar5413.c
193b341d 78
3f720b20
HT
79#
80# AR5416, AR9160 support; these are 11n parts but only really
81# supported (right now) operating in legacy mode. Note enabling
82# this support requires defining AH_SUPPORT_AR5416 in opt_ah.h
83# so the 11n tx/rx descriptor format is handled.
84#
85# NB: 9160 depends on 5416 but 5416 does not require 9160
86#
87.PATH: ${HAL}/ar5416
88SRCS+= ah_eeprom_v14.c \
89 ar5416_ani.c ar5416_attach.c ar5416_beacon.c ar5416_cal.c \
90 ar5416_cal_iq.c ar5416_cal_adcgain.c ar5416_cal_adcdc.c \
91 ar5416_eeprom.c ar5416_gpio.c ar5416_interrupts.c ar5416_keycache.c \
92 ar5416_misc.c ar5416_phy.c ar5416_power.c ar5416_recv.c \
93 ar5416_reset.c ar5416_xmit.c
94SRCS+= ar9160_attach.c
95# RF backend for 5416 and 9160
96SRCS+= ar2133.c
818ddf01
RP
97SRCS+= ar9280_attach.c
98# RF backend for 9280
99SRCS+= ar9280.c
100SRCS+= ah_eeprom_v4k.c ar9285_reset.c ar9285_attach.c
101# RF backend for 9285
102SRCS+= ar9285.c
193b341d 103
3f720b20
HT
104# NB: rate control is bound to the driver by symbol names so only pick one
105#.if ${ATH_RATE} == "sample"
106#.PATH: ${.CURDIR}/../../dev/ath/ath_rate/sample
107#SRCS+= sample.c opt_wlan.h
108#.elif ${ATH_RATE} == "onoe"
109#.PATH: ${.CURDIR}/../../dev/ath/ath_rate/onoe
110#SRCS+= onoe.c
111#.elif ${ATH_RATE} == "amrr"
112#.PATH: ${.CURDIR}/../../dev/ath/ath_rate/amrr
113#SRCS+= amrr.c
114#.endif
193b341d 115
9006a7c3 116CFLAGS+= -I. -I${HAL}
193b341d
SZ
117
118.include <bsd.kmod.mk>