2 * Copyright (c) 2008-2009 Sam Leffler, Errno Consulting
3 * Copyright (c) 2008 Atheros Communications, Inc.
5 * Permission to use, copy, modify, and/or distribute this software for any
6 * purpose with or without fee is hereby granted, provided that the above
7 * copyright notice and this permission notice appear in all copies.
9 * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
10 * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
11 * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
12 * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
13 * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
14 * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
15 * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
22 #include "ah_internal.h"
25 #include "ah_eeprom_v14.h" /* XXX for tx/rx gain */
27 #include "ar9002/ar9280.h"
28 #include "ar5416/ar5416reg.h"
29 #include "ar5416/ar5416phy.h"
31 #include "ar9002/ar9280v1.ini"
32 #include "ar9002/ar9280v2.ini"
33 #include "ar9002/ar9280_olc.h"
35 static const HAL_PERCAL_DATA ar9280_iq_cal = { /* single sample */
36 .calName = "IQ", .calType = IQ_MISMATCH_CAL,
37 .calNumSamples = MIN_CAL_SAMPLES,
38 .calCountMax = PER_MAX_LOG_COUNT,
39 .calCollect = ar5416IQCalCollect,
40 .calPostProc = ar5416IQCalibration
42 static const HAL_PERCAL_DATA ar9280_adc_gain_cal = { /* single sample */
43 .calName = "ADC Gain", .calType = ADC_GAIN_CAL,
44 .calNumSamples = MIN_CAL_SAMPLES,
45 .calCountMax = PER_MAX_LOG_COUNT,
46 .calCollect = ar5416AdcGainCalCollect,
47 .calPostProc = ar5416AdcGainCalibration
49 static const HAL_PERCAL_DATA ar9280_adc_dc_cal = { /* single sample */
50 .calName = "ADC DC", .calType = ADC_DC_CAL,
51 .calNumSamples = MIN_CAL_SAMPLES,
52 .calCountMax = PER_MAX_LOG_COUNT,
53 .calCollect = ar5416AdcDcCalCollect,
54 .calPostProc = ar5416AdcDcCalibration
56 static const HAL_PERCAL_DATA ar9280_adc_init_dc_cal = {
57 .calName = "ADC Init DC", .calType = ADC_DC_INIT_CAL,
58 .calNumSamples = MIN_CAL_SAMPLES,
59 .calCountMax = INIT_LOG_COUNT,
60 .calCollect = ar5416AdcDcCalCollect,
61 .calPostProc = ar5416AdcDcCalibration
64 static void ar9280ConfigPCIE(struct ath_hal *ah, HAL_BOOL restore,
66 static void ar9280DisablePCIE(struct ath_hal *ah);
67 static HAL_BOOL ar9280FillCapabilityInfo(struct ath_hal *ah);
68 static void ar9280WriteIni(struct ath_hal *ah,
69 const struct ieee80211_channel *chan);
72 ar9280AniSetup(struct ath_hal *ah)
75 * These are the parameters from the AR5416 ANI code;
76 * they likely need quite a bit of adjustment for the
79 static const struct ar5212AniParams aniparams = {
80 .maxNoiseImmunityLevel = 4, /* levels 0..4 */
81 .totalSizeDesired = { -55, -55, -55, -55, -62 },
82 .coarseHigh = { -14, -14, -14, -14, -12 },
83 .coarseLow = { -64, -64, -64, -64, -70 },
84 .firpwr = { -78, -78, -78, -78, -80 },
85 .maxSpurImmunityLevel = 7,
86 .cycPwrThr1 = { 2, 4, 6, 8, 10, 12, 14, 16 },
87 .maxFirstepLevel = 2, /* levels 0..2 */
88 .firstep = { 0, 4, 8 },
97 /* NB: disable ANI noise immmunity for reliable RIFS rx */
98 AH5416(ah)->ah_ani_function &= ~(1 << HAL_ANI_NOISE_IMMUNITY_LEVEL);
100 /* NB: ANI is not enabled yet */
101 ar5416AniAttach(ah, &aniparams, &aniparams, AH_TRUE);
105 ar9280InitPLL(struct ath_hal *ah, const struct ieee80211_channel *chan)
107 uint32_t pll = SM(0x5, AR_RTC_SOWL_PLL_REFDIV);
109 if (AR_SREV_MERLIN_20(ah) &&
110 chan != AH_NULL && IEEE80211_IS_CHAN_5GHZ(chan)) {
112 * PLL WAR for Merlin 2.0/2.1
113 * When doing fast clock, set PLL to 0x142c
114 * Else, set PLL to 0x2850 to prevent reset-to-reset variation
116 pll = IS_5GHZ_FAST_CLOCK_EN(ah, chan) ? 0x142c : 0x2850;
117 if (IEEE80211_IS_CHAN_HALF(chan))
118 pll |= SM(0x1, AR_RTC_SOWL_PLL_CLKSEL);
119 else if (IEEE80211_IS_CHAN_QUARTER(chan))
120 pll |= SM(0x2, AR_RTC_SOWL_PLL_CLKSEL);
121 } else if (AR_SREV_MERLIN_10_OR_LATER(ah)) {
122 pll = SM(0x5, AR_RTC_SOWL_PLL_REFDIV);
123 if (chan != AH_NULL) {
124 if (IEEE80211_IS_CHAN_HALF(chan))
125 pll |= SM(0x1, AR_RTC_SOWL_PLL_CLKSEL);
126 else if (IEEE80211_IS_CHAN_QUARTER(chan))
127 pll |= SM(0x2, AR_RTC_SOWL_PLL_CLKSEL);
128 if (IEEE80211_IS_CHAN_5GHZ(chan))
129 pll |= SM(0x28, AR_RTC_SOWL_PLL_DIV);
131 pll |= SM(0x2c, AR_RTC_SOWL_PLL_DIV);
133 pll |= SM(0x2c, AR_RTC_SOWL_PLL_DIV);
136 OS_REG_WRITE(ah, AR_RTC_PLL_CONTROL, pll);
137 OS_DELAY(RTC_PLL_SETTLE_DELAY);
138 OS_REG_WRITE(ah, AR_RTC_SLEEP_CLK, AR_RTC_SLEEP_DERIVED_CLK);
141 /* XXX shouldn't be here! */
142 #define EEP_MINOR(_ah) \
143 (AH_PRIVATE(_ah)->ah_eeversion & AR5416_EEP_VER_MINOR_MASK)
146 * Attach for an AR9280 part.
148 static struct ath_hal *
149 ar9280Attach(uint16_t devid, HAL_SOFTC sc,
150 HAL_BUS_TAG st, HAL_BUS_HANDLE sh, uint16_t *eepromdata,
153 struct ath_hal_9280 *ahp9280;
154 struct ath_hal_5212 *ahp;
159 int8_t pwr_table_offset;
162 HALDEBUG(AH_NULL, HAL_DEBUG_ATTACH, "%s: sc %p st %p sh %p\n",
163 __func__, sc, (void*) st, (void*) sh);
165 /* NB: memory is returned zero'd */
166 ahp9280 = ath_hal_malloc(sizeof (struct ath_hal_9280));
167 if (ahp9280 == AH_NULL) {
168 HALDEBUG(AH_NULL, HAL_DEBUG_ANY,
169 "%s: cannot allocate memory for state block\n", __func__);
170 *status = HAL_ENOMEM;
173 ahp = AH5212(ahp9280);
174 ah = &ahp->ah_priv.h;
176 ar5416InitState(AH5416(ah), devid, sc, st, sh, status);
179 * Use the "local" EEPROM data given to us by the higher layers.
180 * This is a private copy out of system flash. The Linux ath9k
181 * commit for the initial AR9130 support mentions MMIO flash
182 * access is "unreliable." -adrian
184 if (eepromdata != AH_NULL) {
185 AH_PRIVATE((ah))->ah_eepromRead = ath_hal_EepromDataRead;
186 AH_PRIVATE((ah))->ah_eepromWrite = NULL;
187 ah->ah_eepromdata = eepromdata;
190 /* XXX override with 9280 specific state */
191 /* override 5416 methods for our needs */
192 AH5416(ah)->ah_initPLL = ar9280InitPLL;
194 ah->ah_setAntennaSwitch = ar9280SetAntennaSwitch;
195 ah->ah_configPCIE = ar9280ConfigPCIE;
196 ah->ah_disablePCIE = ar9280DisablePCIE;
198 AH5416(ah)->ah_cal.iqCalData.calData = &ar9280_iq_cal;
199 AH5416(ah)->ah_cal.adcGainCalData.calData = &ar9280_adc_gain_cal;
200 AH5416(ah)->ah_cal.adcDcCalData.calData = &ar9280_adc_dc_cal;
201 AH5416(ah)->ah_cal.adcDcCalInitData.calData = &ar9280_adc_init_dc_cal;
202 AH5416(ah)->ah_cal.suppCals = ADC_GAIN_CAL | ADC_DC_CAL | IQ_MISMATCH_CAL;
204 AH5416(ah)->ah_spurMitigate = ar9280SpurMitigate;
205 AH5416(ah)->ah_writeIni = ar9280WriteIni;
206 AH5416(ah)->ah_olcInit = ar9280olcInit;
207 AH5416(ah)->ah_olcTempCompensation = ar9280olcTemperatureCompensation;
208 AH5416(ah)->ah_setPowerCalTable = ar9280SetPowerCalTable;
210 AH5416(ah)->ah_rx_chainmask = AR9280_DEFAULT_RXCHAINMASK;
211 AH5416(ah)->ah_tx_chainmask = AR9280_DEFAULT_TXCHAINMASK;
213 if (!ar5416SetResetReg(ah, HAL_RESET_POWER_ON)) {
215 HALDEBUG(ah, HAL_DEBUG_ANY, "%s: couldn't reset chip\n",
221 if (!ar5416SetPowerMode(ah, HAL_PM_AWAKE, AH_TRUE)) {
222 HALDEBUG(ah, HAL_DEBUG_ANY, "%s: couldn't wakeup chip\n",
227 /* Read Revisions from Chips before taking out of reset */
228 val = OS_REG_READ(ah, AR_SREV);
229 HALDEBUG(ah, HAL_DEBUG_ATTACH,
230 "%s: ID 0x%x VERSION 0x%x TYPE 0x%x REVISION 0x%x\n",
231 __func__, MS(val, AR_XSREV_ID), MS(val, AR_XSREV_VERSION),
232 MS(val, AR_XSREV_TYPE), MS(val, AR_XSREV_REVISION));
233 /* NB: include chip type to differentiate from pre-Sowl versions */
234 AH_PRIVATE(ah)->ah_macVersion =
235 (val & AR_XSREV_VERSION) >> AR_XSREV_TYPE_S;
236 AH_PRIVATE(ah)->ah_macRev = MS(val, AR_XSREV_REVISION);
237 AH_PRIVATE(ah)->ah_ispcie = (val & AR_XSREV_TYPE_HOST_MODE) == 0;
239 /* setup common ini data; rf backends handle remainder */
240 if (AR_SREV_MERLIN_20_OR_LATER(ah)) {
241 HAL_INI_INIT(&ahp->ah_ini_modes, ar9280Modes_v2, 6);
242 HAL_INI_INIT(&ahp->ah_ini_common, ar9280Common_v2, 2);
243 HAL_INI_INIT(&AH5416(ah)->ah_ini_pcieserdes,
244 ar9280PciePhy_clkreq_always_on_L1_v2, 2);
245 HAL_INI_INIT(&ahp9280->ah_ini_xmodes,
246 ar9280Modes_fast_clock_v2, 3);
248 HAL_INI_INIT(&ahp->ah_ini_modes, ar9280Modes_v1, 6);
249 HAL_INI_INIT(&ahp->ah_ini_common, ar9280Common_v1, 2);
250 HAL_INI_INIT(&AH5416(ah)->ah_ini_pcieserdes,
251 ar9280PciePhy_v1, 2);
253 ar5416AttachPCIE(ah);
255 ecode = ath_hal_v14EepromAttach(ah);
259 if (!ar5416ChipReset(ah, AH_NULL)) { /* reset chip */
260 HALDEBUG(ah, HAL_DEBUG_ANY, "%s: chip reset failed\n", __func__);
265 AH_PRIVATE(ah)->ah_phyRev = OS_REG_READ(ah, AR_PHY_CHIP_ID);
267 if (!ar5212ChipTest(ah)) {
268 HALDEBUG(ah, HAL_DEBUG_ANY, "%s: hardware self-test failed\n",
270 ecode = HAL_ESELFTEST;
275 * Set correct Baseband to analog shift
276 * setting to access analog chips.
278 OS_REG_WRITE(ah, AR_PHY(0), 0x00000007);
280 /* Read Radio Chip Rev Extract */
281 AH_PRIVATE(ah)->ah_analog5GhzRev = ar5416GetRadioRev(ah);
282 switch (AH_PRIVATE(ah)->ah_analog5GhzRev & AR_RADIO_SREV_MAJOR) {
283 case AR_RAD2133_SREV_MAJOR: /* Sowl: 2G/3x3 */
284 case AR_RAD5133_SREV_MAJOR: /* Sowl: 2+5G/3x3 */
287 if (AH_PRIVATE(ah)->ah_analog5GhzRev == 0) {
288 AH_PRIVATE(ah)->ah_analog5GhzRev =
289 AR_RAD5133_SREV_MAJOR;
293 HALDEBUG(ah, HAL_DEBUG_ANY,
294 "%s: 5G Radio Chip Rev 0x%02X is not supported by "
295 "this driver\n", __func__,
296 AH_PRIVATE(ah)->ah_analog5GhzRev);
297 ecode = HAL_ENOTSUPP;
301 rfStatus = ar9280RfAttach(ah, &ecode);
303 HALDEBUG(ah, HAL_DEBUG_ANY, "%s: RF setup failed, status %u\n",
308 /* Enable fixup for AR_AN_TOP2 if necessary */
310 * The v14 EEPROM layer returns HAL_EIO if PWDCLKIND isn't supported
311 * by the EEPROM version.
313 * ath9k checks the EEPROM minor version is >= 0x0a here, instead of
314 * the abstracted EEPROM access layer.
316 ecode = ath_hal_eepromGet(ah, AR_EEP_PWDCLKIND, &pwr);
317 if (AR_SREV_MERLIN_20_OR_LATER(ah) && ecode == HAL_OK && pwr == 0) {
318 printf("[ath] enabling AN_TOP2_FIXUP\n");
319 AH5416(ah)->ah_need_an_top2_fixup = 1;
323 * Check whether the power table offset isn't the default.
324 * This can occur with eeprom minor V21 or greater on Merlin.
326 (void) ath_hal_eepromGet(ah, AR_EEP_PWR_TABLE_OFFSET, &pwr_table_offset);
327 if (pwr_table_offset != AR5416_PWR_TABLE_OFFSET_DB)
328 ath_hal_printf(ah, "[ath]: default pwr offset: %d dBm != EEPROM pwr offset: %d dBm; curves will be adjusted.\n",
329 AR5416_PWR_TABLE_OFFSET_DB, (int) pwr_table_offset);
331 /* XXX check for >= minor ver 17 */
332 if (AR_SREV_MERLIN_20(ah)) {
333 /* setup rxgain table */
334 switch (ath_hal_eepromGet(ah, AR_EEP_RXGAIN_TYPE, AH_NULL)) {
335 case AR5416_EEP_RXGAIN_13dB_BACKOFF:
336 HAL_INI_INIT(&ahp9280->ah_ini_rxgain,
337 ar9280Modes_backoff_13db_rxgain_v2, 6);
339 case AR5416_EEP_RXGAIN_23dB_BACKOFF:
340 HAL_INI_INIT(&ahp9280->ah_ini_rxgain,
341 ar9280Modes_backoff_23db_rxgain_v2, 6);
343 case AR5416_EEP_RXGAIN_ORIG:
344 HAL_INI_INIT(&ahp9280->ah_ini_rxgain,
345 ar9280Modes_original_rxgain_v2, 6);
349 goto bad; /* XXX ? try to continue */
353 /* XXX check for >= minor ver 19 */
354 if (AR_SREV_MERLIN_20(ah)) {
355 /* setp txgain table */
356 switch (ath_hal_eepromGet(ah, AR_EEP_TXGAIN_TYPE, AH_NULL)) {
357 case AR5416_EEP_TXGAIN_HIGH_POWER:
358 HAL_INI_INIT(&ahp9280->ah_ini_txgain,
359 ar9280Modes_high_power_tx_gain_v2, 6);
361 case AR5416_EEP_TXGAIN_ORIG:
362 HAL_INI_INIT(&ahp9280->ah_ini_txgain,
363 ar9280Modes_original_tx_gain_v2, 6);
367 goto bad; /* XXX ? try to continue */
372 * Got everything we need now to setup the capabilities.
374 if (!ar9280FillCapabilityInfo(ah)) {
379 ecode = ath_hal_eepromGet(ah, AR_EEP_MACADDR, ahp->ah_macaddr);
380 if (ecode != HAL_OK) {
381 HALDEBUG(ah, HAL_DEBUG_ANY,
382 "%s: error getting mac address from EEPROM\n", __func__);
385 /* XXX How about the serial number ? */
386 /* Read Reg Domain */
387 AH_PRIVATE(ah)->ah_currentRD =
388 ath_hal_eepromGet(ah, AR_EEP_REGDMN_0, AH_NULL);
389 AH_PRIVATE(ah)->ah_currentRDext =
390 ath_hal_eepromGet(ah, AR_EEP_REGDMN_1, AH_NULL);
393 * ah_miscMode is populated by ar5416FillCapabilityInfo()
394 * starting from griffin. Set here to make sure that
395 * AR_MISC_MODE_MIC_NEW_LOC_ENABLE is set before a GTK is
396 * placed into hardware.
398 if (ahp->ah_miscMode != 0)
399 OS_REG_WRITE(ah, AR_MISC_MODE, OS_REG_READ(ah, AR_MISC_MODE) | ahp->ah_miscMode);
401 ar9280AniSetup(ah); /* Anti Noise Immunity */
403 /* Setup noise floor min/max/nominal values */
404 AH5416(ah)->nf_2g.max = AR_PHY_CCA_MAX_GOOD_VAL_9280_2GHZ;
405 AH5416(ah)->nf_2g.min = AR_PHY_CCA_MIN_GOOD_VAL_9280_2GHZ;
406 AH5416(ah)->nf_2g.nominal = AR_PHY_CCA_NOM_VAL_9280_2GHZ;
407 AH5416(ah)->nf_5g.max = AR_PHY_CCA_MAX_GOOD_VAL_9280_5GHZ;
408 AH5416(ah)->nf_5g.min = AR_PHY_CCA_MIN_GOOD_VAL_9280_5GHZ;
409 AH5416(ah)->nf_5g.nominal = AR_PHY_CCA_NOM_VAL_9280_5GHZ;
411 ar5416InitNfHistBuff(AH5416(ah)->ah_cal.nfCalHist);
413 HALDEBUG(ah, HAL_DEBUG_ATTACH, "%s: return\n", __func__);
425 ar9280ConfigPCIE(struct ath_hal *ah, HAL_BOOL restore, HAL_BOOL power_off)
429 if (AH_PRIVATE(ah)->ah_ispcie && !restore) {
430 ath_hal_ini_write(ah, &AH5416(ah)->ah_ini_pcieserdes, 1, 0);
436 * Set PCIe workaround bits
440 * In Merlin and Kite, bit 14 in WA register (disable L1) should only
441 * be set when device enters D3 and be cleared when device comes back
444 if (power_off) { /* Power-off */
445 OS_REG_CLR_BIT(ah, AR_PCIE_PM_CTRL, AR_PCIE_PM_CTRL_ENA);
447 val = OS_REG_READ(ah, AR_WA);
450 * Disable bit 6 and 7 before entering D3 to prevent
453 val &= ~(AR_WA_BIT6 | AR_WA_BIT7);
456 * XXX Not sure, is specified in the reference HAL.
461 * See above: set AR_WA_D3_L1_DISABLE when entering D3 state.
463 * XXX The reference HAL does it this way - it only sets
464 * AR_WA_D3_L1_DISABLE if it's set in AR9280_WA_DEFAULT,
465 * which it (currently) isn't. So the following statement
466 * is currently a NOP.
468 if (AR9280_WA_DEFAULT & AR_WA_D3_L1_DISABLE)
469 val |= AR_WA_D3_L1_DISABLE;
471 OS_REG_WRITE(ah, AR_WA, val);
472 } else { /* Power-on */
473 val = AR9280_WA_DEFAULT;
476 * See note above: make sure L1_DISABLE is not set.
478 val &= (~AR_WA_D3_L1_DISABLE);
479 OS_REG_WRITE(ah, AR_WA, val);
481 /* set bit 19 to allow forcing of pcie core into L1 state */
482 OS_REG_SET_BIT(ah, AR_PCIE_PM_CTRL, AR_PCIE_PM_CTRL_ENA);
487 ar9280DisablePCIE(struct ath_hal *ah)
492 ar9280WriteIni(struct ath_hal *ah, const struct ieee80211_channel *chan)
494 u_int modesIndex, freqIndex;
497 const HAL_INI_ARRAY *ia;
499 /* Setup the indices for the next set of register array writes */
500 /* XXX Ignore 11n dynamic mode on the AR5416 for the moment */
501 if (IEEE80211_IS_CHAN_2GHZ(chan)) {
503 if (IEEE80211_IS_CHAN_HT40(chan))
505 else if (IEEE80211_IS_CHAN_108G(chan))
511 if (IEEE80211_IS_CHAN_HT40(chan) ||
512 IEEE80211_IS_CHAN_TURBO(chan))
518 /* Set correct Baseband to analog shift setting to access analog chips. */
519 OS_REG_WRITE(ah, AR_PHY(0), 0x00000007);
520 OS_REG_WRITE(ah, AR_PHY_ADC_SERIAL_CTL, AR_PHY_SEL_INTERNAL_ADDAC);
523 * This is unwound because at the moment, there's a requirement
524 * for Merlin (and later, perhaps) to have a specific bit fixed
525 * in the AR_AN_TOP2 register before writing it.
527 ia = &AH5212(ah)->ah_ini_modes;
529 regWrites = ath_hal_ini_write(ah, &AH5212(ah)->ah_ini_modes,
530 modesIndex, regWrites);
532 HALASSERT(modesIndex < ia->cols);
533 for (i = 0; i < ia->rows; i++) {
534 uint32_t reg = HAL_INI_VAL(ia, i, 0);
535 uint32_t val = HAL_INI_VAL(ia, i, modesIndex);
537 if (reg == AR_AN_TOP2 && AH5416(ah)->ah_need_an_top2_fixup)
538 val &= ~AR_AN_TOP2_PWDCLKIND;
540 OS_REG_WRITE(ah, reg, val);
542 /* Analog shift register delay seems needed for Merlin - PR kern/154220 */
543 if (reg >= 0x7800 && reg < 0x7900)
546 DMA_YIELD(regWrites);
549 if (AR_SREV_MERLIN_20_OR_LATER(ah)) {
550 regWrites = ath_hal_ini_write(ah, &AH9280(ah)->ah_ini_rxgain,
551 modesIndex, regWrites);
552 regWrites = ath_hal_ini_write(ah, &AH9280(ah)->ah_ini_txgain,
553 modesIndex, regWrites);
555 /* XXX Merlin 100us delay for shift registers */
556 regWrites = ath_hal_ini_write(ah, &AH5212(ah)->ah_ini_common,
559 if (AR_SREV_MERLIN_20(ah) && IS_5GHZ_FAST_CLOCK_EN(ah, chan)) {
560 /* 5GHz channels w/ Fast Clock use different modal values */
561 regWrites = ath_hal_ini_write(ah, &AH9280(ah)->ah_ini_xmodes,
562 modesIndex, regWrites);
566 #define AR_BASE_FREQ_2GHZ 2300
567 #define AR_BASE_FREQ_5GHZ 4900
568 #define AR_SPUR_FEEQ_BOUND_HT40 19
569 #define AR_SPUR_FEEQ_BOUND_HT20 10
572 ar9280SpurMitigate(struct ath_hal *ah, const struct ieee80211_channel *chan)
574 static const int pilot_mask_reg[4] = { AR_PHY_TIMING7, AR_PHY_TIMING8,
575 AR_PHY_PILOT_MASK_01_30, AR_PHY_PILOT_MASK_31_60 };
576 static const int chan_mask_reg[4] = { AR_PHY_TIMING9, AR_PHY_TIMING10,
577 AR_PHY_CHANNEL_MASK_01_30, AR_PHY_CHANNEL_MASK_31_60 };
578 static int inc[4] = { 0, 100, 0, 0 };
580 int bb_spur = AR_NO_SPUR;
583 int bb_spur_off, spur_subchannel_sd;
585 int spur_delta_phase;
587 int upper, lower, cur_vit_mask;
590 CHAN_CENTERS centers;
597 HAL_BOOL is2GHz = IEEE80211_IS_CHAN_2GHZ(chan);
599 OS_MEMZERO(&mask_m, sizeof(int8_t) * 123);
600 OS_MEMZERO(&mask_p, sizeof(int8_t) * 123);
602 ar5416GetChannelCenters(ah, chan, ¢ers);
603 freq = centers.synth_center;
606 * Need to verify range +/- 9.38 for static ht20 and +/- 18.75 for ht40,
607 * otherwise spur is out-of-band and can be ignored.
609 for (i = 0; i < AR5416_EEPROM_MODAL_SPURS; i++) {
610 cur_bb_spur = ath_hal_getSpurChan(ah, i, is2GHz);
611 /* Get actual spur freq in MHz from EEPROM read value */
613 cur_bb_spur = (cur_bb_spur / 10) + AR_BASE_FREQ_2GHZ;
615 cur_bb_spur = (cur_bb_spur / 10) + AR_BASE_FREQ_5GHZ;
618 if (AR_NO_SPUR == cur_bb_spur)
620 cur_bb_spur = cur_bb_spur - freq;
622 if (IEEE80211_IS_CHAN_HT40(chan)) {
623 if ((cur_bb_spur > -AR_SPUR_FEEQ_BOUND_HT40) &&
624 (cur_bb_spur < AR_SPUR_FEEQ_BOUND_HT40)) {
625 bb_spur = cur_bb_spur;
628 } else if ((cur_bb_spur > -AR_SPUR_FEEQ_BOUND_HT20) &&
629 (cur_bb_spur < AR_SPUR_FEEQ_BOUND_HT20)) {
630 bb_spur = cur_bb_spur;
635 if (AR_NO_SPUR == bb_spur) {
638 * MRC CCK can interfere with beacon detection and cause deaf/mute.
639 * Disable MRC CCK for now.
641 OS_REG_CLR_BIT(ah, AR_PHY_FORCE_CLKEN_CCK, AR_PHY_FORCE_CLKEN_CCK_MRC_MUX);
643 /* Enable MRC CCK if no spur is found in this channel. */
644 OS_REG_SET_BIT(ah, AR_PHY_FORCE_CLKEN_CCK, AR_PHY_FORCE_CLKEN_CCK_MRC_MUX);
649 * For Merlin, spur can break CCK MRC algorithm. Disable CCK MRC if spur
650 * is found in this channel.
652 OS_REG_CLR_BIT(ah, AR_PHY_FORCE_CLKEN_CCK, AR_PHY_FORCE_CLKEN_CCK_MRC_MUX);
657 tmp = OS_REG_READ(ah, AR_PHY_TIMING_CTRL4_CHAIN(0));
659 newVal = tmp | (AR_PHY_TIMING_CTRL4_ENABLE_SPUR_RSSI |
660 AR_PHY_TIMING_CTRL4_ENABLE_SPUR_FILTER |
661 AR_PHY_TIMING_CTRL4_ENABLE_CHAN_MASK |
662 AR_PHY_TIMING_CTRL4_ENABLE_PILOT_MASK);
663 OS_REG_WRITE(ah, AR_PHY_TIMING_CTRL4_CHAIN(0), newVal);
665 newVal = (AR_PHY_SPUR_REG_MASK_RATE_CNTL |
666 AR_PHY_SPUR_REG_ENABLE_MASK_PPM |
667 AR_PHY_SPUR_REG_MASK_RATE_SELECT |
668 AR_PHY_SPUR_REG_ENABLE_VIT_SPUR_RSSI |
669 SM(AR5416_SPUR_RSSI_THRESH, AR_PHY_SPUR_REG_SPUR_RSSI_THRESH));
670 OS_REG_WRITE(ah, AR_PHY_SPUR_REG, newVal);
672 /* Pick control or extn channel to cancel the spur */
673 if (IEEE80211_IS_CHAN_HT40(chan)) {
675 spur_subchannel_sd = 1;
676 bb_spur_off = bb_spur + 10;
678 spur_subchannel_sd = 0;
679 bb_spur_off = bb_spur - 10;
682 spur_subchannel_sd = 0;
683 bb_spur_off = bb_spur;
687 * spur_delta_phase = bb_spur/40 * 2**21 for static ht20,
690 if (IEEE80211_IS_CHAN_HT40(chan))
691 spur_delta_phase = ((bb_spur * 262144) / 10) & AR_PHY_TIMING11_SPUR_DELTA_PHASE;
693 spur_delta_phase = ((bb_spur * 524288) / 10) & AR_PHY_TIMING11_SPUR_DELTA_PHASE;
696 * in 11A mode the denominator of spur_freq_sd should be 40 and
697 * it should be 44 in 11G
699 denominator = IEEE80211_IS_CHAN_2GHZ(chan) ? 44 : 40;
700 spur_freq_sd = ((bb_spur_off * 2048) / denominator) & 0x3ff;
702 newVal = (AR_PHY_TIMING11_USE_SPUR_IN_AGC |
703 SM(spur_freq_sd, AR_PHY_TIMING11_SPUR_FREQ_SD) |
704 SM(spur_delta_phase, AR_PHY_TIMING11_SPUR_DELTA_PHASE));
705 OS_REG_WRITE(ah, AR_PHY_TIMING11, newVal);
707 /* Choose to cancel between control and extension channels */
708 newVal = spur_subchannel_sd << AR_PHY_SFCORR_SPUR_SUBCHNL_SD_S;
709 OS_REG_WRITE(ah, AR_PHY_SFCORR_EXT, newVal);
712 * ============================================
713 * Set Pilot and Channel Masks
715 * pilot mask 1 [31:0] = +6..-26, no 0 bin
716 * pilot mask 2 [19:0] = +26..+7
718 * channel mask 1 [31:0] = +6..-26, no 0 bin
719 * channel mask 2 [19:0] = +26..+7
725 for (i = 0; i < 4; i++) {
729 for (bp = 0; bp < 30; bp++) {
730 if ((cur_bin > lower) && (cur_bin < upper)) {
731 pilot_mask = pilot_mask | 0x1 << bp;
732 chan_mask = chan_mask | 0x1 << bp;
737 OS_REG_WRITE(ah, pilot_mask_reg[i], pilot_mask);
738 OS_REG_WRITE(ah, chan_mask_reg[i], chan_mask);
741 /* =================================================
742 * viterbi mask 1 based on channel magnitude
744 * - mask (-27 to 27) (reg 64,0x9900 to 67,0x990c)
745 * [1 2 2 1] for -9.6 or [1 2 1] for +16
746 * - enable_mask_ppm, all bins move with freq
748 * - mask_select, 8 bits for rates (reg 67,0x990c)
749 * - mask_rate_cntl, 8 bits for rates (reg 67,0x990c)
750 * choose which mask to use mask or mask2
754 * viterbi mask 2 2nd set for per data rate puncturing
756 * - mask_select, 8 bits for rates (reg 67)
757 * - mask (-27 to 27) (reg 98,0x9988 to 101,0x9994)
758 * [1 2 2 1] for -9.6 or [1 2 1] for +16
764 for (i = 0; i < 123; i++) {
765 if ((cur_vit_mask > lower) && (cur_vit_mask < upper)) {
766 if ((abs(cur_vit_mask - bin)) < 75) {
771 if (cur_vit_mask < 0) {
772 mask_m[abs(cur_vit_mask / 100)] = mask_amt;
774 mask_p[cur_vit_mask / 100] = mask_amt;
780 tmp_mask = (mask_m[46] << 30) | (mask_m[47] << 28)
781 | (mask_m[48] << 26) | (mask_m[49] << 24)
782 | (mask_m[50] << 22) | (mask_m[51] << 20)
783 | (mask_m[52] << 18) | (mask_m[53] << 16)
784 | (mask_m[54] << 14) | (mask_m[55] << 12)
785 | (mask_m[56] << 10) | (mask_m[57] << 8)
786 | (mask_m[58] << 6) | (mask_m[59] << 4)
787 | (mask_m[60] << 2) | (mask_m[61] << 0);
788 OS_REG_WRITE(ah, AR_PHY_BIN_MASK_1, tmp_mask);
789 OS_REG_WRITE(ah, AR_PHY_VIT_MASK2_M_46_61, tmp_mask);
791 tmp_mask = (mask_m[31] << 28)
792 | (mask_m[32] << 26) | (mask_m[33] << 24)
793 | (mask_m[34] << 22) | (mask_m[35] << 20)
794 | (mask_m[36] << 18) | (mask_m[37] << 16)
795 | (mask_m[48] << 14) | (mask_m[39] << 12)
796 | (mask_m[40] << 10) | (mask_m[41] << 8)
797 | (mask_m[42] << 6) | (mask_m[43] << 4)
798 | (mask_m[44] << 2) | (mask_m[45] << 0);
799 OS_REG_WRITE(ah, AR_PHY_BIN_MASK_2, tmp_mask);
800 OS_REG_WRITE(ah, AR_PHY_MASK2_M_31_45, tmp_mask);
802 tmp_mask = (mask_m[16] << 30) | (mask_m[16] << 28)
803 | (mask_m[18] << 26) | (mask_m[18] << 24)
804 | (mask_m[20] << 22) | (mask_m[20] << 20)
805 | (mask_m[22] << 18) | (mask_m[22] << 16)
806 | (mask_m[24] << 14) | (mask_m[24] << 12)
807 | (mask_m[25] << 10) | (mask_m[26] << 8)
808 | (mask_m[27] << 6) | (mask_m[28] << 4)
809 | (mask_m[29] << 2) | (mask_m[30] << 0);
810 OS_REG_WRITE(ah, AR_PHY_BIN_MASK_3, tmp_mask);
811 OS_REG_WRITE(ah, AR_PHY_MASK2_M_16_30, tmp_mask);
813 tmp_mask = (mask_m[ 0] << 30) | (mask_m[ 1] << 28)
814 | (mask_m[ 2] << 26) | (mask_m[ 3] << 24)
815 | (mask_m[ 4] << 22) | (mask_m[ 5] << 20)
816 | (mask_m[ 6] << 18) | (mask_m[ 7] << 16)
817 | (mask_m[ 8] << 14) | (mask_m[ 9] << 12)
818 | (mask_m[10] << 10) | (mask_m[11] << 8)
819 | (mask_m[12] << 6) | (mask_m[13] << 4)
820 | (mask_m[14] << 2) | (mask_m[15] << 0);
821 OS_REG_WRITE(ah, AR_PHY_MASK_CTL, tmp_mask);
822 OS_REG_WRITE(ah, AR_PHY_MASK2_M_00_15, tmp_mask);
824 tmp_mask = (mask_p[15] << 28)
825 | (mask_p[14] << 26) | (mask_p[13] << 24)
826 | (mask_p[12] << 22) | (mask_p[11] << 20)
827 | (mask_p[10] << 18) | (mask_p[ 9] << 16)
828 | (mask_p[ 8] << 14) | (mask_p[ 7] << 12)
829 | (mask_p[ 6] << 10) | (mask_p[ 5] << 8)
830 | (mask_p[ 4] << 6) | (mask_p[ 3] << 4)
831 | (mask_p[ 2] << 2) | (mask_p[ 1] << 0);
832 OS_REG_WRITE(ah, AR_PHY_BIN_MASK2_1, tmp_mask);
833 OS_REG_WRITE(ah, AR_PHY_MASK2_P_15_01, tmp_mask);
835 tmp_mask = (mask_p[30] << 28)
836 | (mask_p[29] << 26) | (mask_p[28] << 24)
837 | (mask_p[27] << 22) | (mask_p[26] << 20)
838 | (mask_p[25] << 18) | (mask_p[24] << 16)
839 | (mask_p[23] << 14) | (mask_p[22] << 12)
840 | (mask_p[21] << 10) | (mask_p[20] << 8)
841 | (mask_p[19] << 6) | (mask_p[18] << 4)
842 | (mask_p[17] << 2) | (mask_p[16] << 0);
843 OS_REG_WRITE(ah, AR_PHY_BIN_MASK2_2, tmp_mask);
844 OS_REG_WRITE(ah, AR_PHY_MASK2_P_30_16, tmp_mask);
846 tmp_mask = (mask_p[45] << 28)
847 | (mask_p[44] << 26) | (mask_p[43] << 24)
848 | (mask_p[42] << 22) | (mask_p[41] << 20)
849 | (mask_p[40] << 18) | (mask_p[39] << 16)
850 | (mask_p[38] << 14) | (mask_p[37] << 12)
851 | (mask_p[36] << 10) | (mask_p[35] << 8)
852 | (mask_p[34] << 6) | (mask_p[33] << 4)
853 | (mask_p[32] << 2) | (mask_p[31] << 0);
854 OS_REG_WRITE(ah, AR_PHY_BIN_MASK2_3, tmp_mask);
855 OS_REG_WRITE(ah, AR_PHY_MASK2_P_45_31, tmp_mask);
857 tmp_mask = (mask_p[61] << 30) | (mask_p[60] << 28)
858 | (mask_p[59] << 26) | (mask_p[58] << 24)
859 | (mask_p[57] << 22) | (mask_p[56] << 20)
860 | (mask_p[55] << 18) | (mask_p[54] << 16)
861 | (mask_p[53] << 14) | (mask_p[52] << 12)
862 | (mask_p[51] << 10) | (mask_p[50] << 8)
863 | (mask_p[49] << 6) | (mask_p[48] << 4)
864 | (mask_p[47] << 2) | (mask_p[46] << 0);
865 OS_REG_WRITE(ah, AR_PHY_BIN_MASK2_4, tmp_mask);
866 OS_REG_WRITE(ah, AR_PHY_MASK2_P_61_45, tmp_mask);
870 * Fill all software cached or static hardware state information.
871 * Return failure if capabilities are to come from EEPROM and
875 ar9280FillCapabilityInfo(struct ath_hal *ah)
877 HAL_CAPABILITIES *pCap = &AH_PRIVATE(ah)->ah_caps;
879 if (!ar5416FillCapabilityInfo(ah))
881 pCap->halNumGpioPins = 10;
882 pCap->halWowSupport = AH_TRUE;
883 pCap->halWowMatchPatternExact = AH_TRUE;
885 pCap->halWowMatchPatternDword = AH_TRUE;
887 pCap->halCSTSupport = AH_TRUE;
888 pCap->halRifsRxSupport = AH_TRUE;
889 pCap->halRifsTxSupport = AH_TRUE;
890 pCap->halRtsAggrLimit = 64*1024; /* 802.11n max */
891 pCap->halExtChanDfsSupport = AH_TRUE;
892 pCap->halUseCombinedRadarRssi = AH_TRUE;
895 pCap->halBtCoexSupport = AH_TRUE;
897 pCap->halAutoSleepSupport = AH_FALSE; /* XXX? */
898 pCap->hal4kbSplitTransSupport = AH_FALSE;
899 /* Disable this so Block-ACK works correctly */
900 pCap->halHasRxSelfLinkedTail = AH_FALSE;
901 pCap->halMbssidAggrSupport = AH_TRUE;
902 pCap->hal4AddrAggrSupport = AH_TRUE;
903 pCap->halSpectralScanSupport = AH_TRUE;
905 if (AR_SREV_MERLIN_20(ah)) {
906 pCap->halPSPollBroken = AH_FALSE;
908 * This just enables the support; it doesn't
909 * state 5ghz fast clock will always be used.
911 pCap->halSupportsFastClock5GHz = AH_TRUE;
913 pCap->halRxStbcSupport = 1;
914 pCap->halTxStbcSupport = 1;
915 pCap->halEnhancedDfsSupport = AH_TRUE;
921 * This has been disabled - having the HAL flip chainmasks on/off
922 * when attempting to implement 11n disrupts things. For now, just
923 * leave this flipped off and worry about implementing TX diversity
924 * for legacy and MCS0-7 when 11n is fully functioning.
927 ar9280SetAntennaSwitch(struct ath_hal *ah, HAL_ANT_SETTING settings)
929 #define ANTENNA0_CHAINMASK 0x1
930 #define ANTENNA1_CHAINMASK 0x2
932 struct ath_hal_5416 *ahp = AH5416(ah);
934 /* Antenna selection is done by setting the tx/rx chainmasks approp. */
936 case HAL_ANT_FIXED_A:
937 /* Enable first antenna only */
938 ahp->ah_tx_chainmask = ANTENNA0_CHAINMASK;
939 ahp->ah_rx_chainmask = ANTENNA0_CHAINMASK;
941 case HAL_ANT_FIXED_B:
942 /* Enable second antenna only, after checking capability */
943 if (AH_PRIVATE(ah)->ah_caps.halTxChainMask > ANTENNA1_CHAINMASK)
944 ahp->ah_tx_chainmask = ANTENNA1_CHAINMASK;
945 ahp->ah_rx_chainmask = ANTENNA1_CHAINMASK;
947 case HAL_ANT_VARIABLE:
948 /* Restore original chainmask settings */
950 ahp->ah_tx_chainmask = AR9280_DEFAULT_TXCHAINMASK;
951 ahp->ah_rx_chainmask = AR9280_DEFAULT_RXCHAINMASK;
955 HALDEBUG(ah, HAL_DEBUG_ANY, "%s: settings=%d, tx/rx chainmask=%d/%d\n",
956 __func__, settings, ahp->ah_tx_chainmask, ahp->ah_rx_chainmask);
960 #undef ANTENNA0_CHAINMASK
961 #undef ANTENNA1_CHAINMASK
965 ar9280Probe(uint16_t vendorid, uint16_t devid)
967 if (vendorid == ATHEROS_VENDOR_ID) {
968 if (devid == AR9280_DEVID_PCI)
969 return "Atheros 9220";
970 if (devid == AR9280_DEVID_PCIE)
971 return "Atheros 9280";
975 AH_CHIP(AR9280, ar9280Probe, ar9280Attach);