2 * cyclades cyclom-y serial driver
3 * Andrew Herbert <andrew@werple.apana.org.au>, 17 August 1993
5 * Copyright (c) 1993 Andrew Herbert.
8 * Redistribution and use in source and binary forms, with or without
9 * modification, are permitted provided that the following conditions
11 * 1. Redistributions of source code must retain the above copyright
12 * notice, this list of conditions and the following disclaimer.
13 * 2. Redistributions in binary form must reproduce the above copyright
14 * notice, this list of conditions and the following disclaimer in the
15 * documentation and/or other materials provided with the distribution.
16 * 3. The name Andrew Herbert may not be used to endorse or promote products
17 * derived from this software without specific prior written permission.
19 * THIS SOFTWARE IS PROVIDED BY ``AS IS'' AND ANY EXPRESS OR IMPLIED
20 * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
21 * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
22 * NO EVENT SHALL I BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
23 * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
24 * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
25 * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
26 * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
27 * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
28 * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
30 * $FreeBSD: src/sys/i386/isa/cy.c,v 1.97.2.2 2001/08/22 13:04:58 bde Exp $
31 * $DragonFly: src/sys/dev/serial/cy/cy.c,v 1.4 2003/07/19 21:14:34 dillon Exp $
34 #include "opt_compat.h"
44 * Temporary compile-time configuration options.
46 #define RxFifoThreshold (CD1400_RX_FIFO_SIZE / 2)
47 /* Number of chars in the receiver FIFO before an
48 * an interrupt is generated. Should depend on
49 * line speed. Needs to be about 6 on a 486DX33
50 * for 4 active ports at 115200 bps. Why doesn't
53 #define PollMode /* Use polling-based irq service routine, not the
54 * hardware svcack lines. Must be defined for
55 * Cyclom-16Y boards. Less efficient for Cyclom-8Ys,
56 * and stops 4 * 115200 bps from working.
58 #undef Smarts /* Enable slightly more CD1400 intelligence. Mainly
59 * the output CR/LF processing, plus we can avoid a
60 * few checks usually done in ttyinput().
62 * XXX not fully implemented, and not particularly
65 #undef CyDebug /* Include debugging code (not very expensive). */
67 /* These will go away. */
71 #include <sys/param.h>
72 #include <sys/systm.h>
76 #include <sys/dkstat.h>
77 #include <sys/fcntl.h>
78 #include <sys/interrupt.h>
79 #include <sys/kernel.h>
80 #include <sys/malloc.h>
81 #include <sys/syslog.h>
82 #include <machine/clock.h>
83 #include <machine/ipl.h>
85 #include <machine/lock.h>
87 #include <machine/psl.h>
89 #include <i386/isa/isa_device.h>
90 #include <i386/isa/cyreg.h>
91 #include <i386/isa/ic/cd1400.h>
94 #define disable_intr() COM_DISABLE_INTR()
95 #define enable_intr() COM_ENABLE_INTR()
99 * Dictionary so that I can name everything *sio* or *com* to compare with
100 * sio.c. There is also lots of ugly formatting and unnecessary ifdefs to
101 * simplify the comparision. These will go away.
103 #define LSR_BI CD1400_RDSR_BREAK
104 #define LSR_FE CD1400_RDSR_FE
105 #define LSR_OE CD1400_RDSR_OE
106 #define LSR_PE CD1400_RDSR_PE
107 #define MCR_DTR CD1400_MSVR2_DTR
108 #define MCR_RTS CD1400_MSVR1_RTS
109 #define MSR_CTS CD1400_MSVR2_CTS
110 #define MSR_DCD CD1400_MSVR2_CD
111 #define MSR_DSR CD1400_MSVR2_DSR
112 #define MSR_RI CD1400_MSVR2_RI
113 #define NSIO (NCY * CY_MAX_PORTS)
114 #define comconsole cyconsole
115 #define comdefaultrate cydefaultrate
116 #define com_events cy_events
117 #define comhardclose cyhardclose
118 #define commctl cymctl
119 #define comparam cyparam
120 #define comspeed cyspeed
121 #define comstart cystart
122 #define comwakeup cywakeup
123 #define nsio_tty ncy_tty
124 #define p_com_addr p_cy_addr
125 #define sioattach cyattach
126 #define sioclose cyclose
127 #define siodriver cydriver
128 #define siodtrwakeup cydtrwakeup
129 #define sioinput cyinput
130 #define siointr cyintr
131 #define siointr1 cyintr1
132 #define sioioctl cyioctl
133 #define sioopen cyopen
134 #define siopoll cypoll
135 #define sioprobe cyprobe
136 #define siosettimeout cysettimeout
137 #define siosetwater cysetwater
138 #define comstop cystop
139 #define siowrite cywrite
140 #define sio_registered cy_registered
141 #define sio_timeout cy_timeout
142 #define sio_timeout_handle cy_timeout_handle
143 #define sio_timeouts_until_log cy_timeouts_until_log
144 #define sio_tty cy_tty
146 #define CY_MAX_PORTS (CD1400_NO_OF_CHANNELS * CY_MAX_CD1400s)
148 /* We encode the cyclom unit number (cyu) in spare bits in the IVR's. */
149 #define CD1400_xIVR_CHAN_SHIFT 3
150 #define CD1400_xIVR_CHAN 0x1F
153 * ETC states. com->etc may also contain a hardware ETC command value,
154 * meaning that execution of that command is pending.
156 #define ETC_NONE 0 /* we depend on bzero() setting this */
157 #define ETC_BREAK_STARTING 1
158 #define ETC_BREAK_STARTED 2
159 #define ETC_BREAK_ENDING 3
160 #define ETC_BREAK_ENDED 4
162 #define LOTS_OF_EVENTS 64 /* helps separate urgent events from input */
164 #define CALLOUT_MASK 0x80
165 #define CONTROL_MASK 0x60
166 #define CONTROL_INIT_STATE 0x20
167 #define CONTROL_LOCK_STATE 0x40
168 #define DEV_TO_UNIT(dev) (MINOR_TO_UNIT(minor(dev)))
169 #define MINOR_MAGIC_MASK (CALLOUT_MASK | CONTROL_MASK)
171 * Not all of the magic is parametrized in the following macros. 16 and
172 * 0xff are related to the bitfields in a udev_t. CY_MAX_PORTS must be
173 * ((0xff & ~MINOR_MAGIC_MASK) + 1) for things to work.
175 #define MINOR_TO_UNIT(mynor) (((mynor) >> 16) * CY_MAX_PORTS \
176 | (((mynor) & 0xff) & ~MINOR_MAGIC_MASK))
177 #define UNIT_TO_MINOR(unit) (((unit) / CY_MAX_PORTS) << 16 \
178 | (((unit) & 0xff) & ~MINOR_MAGIC_MASK))
182 * (CS_BUSY | CS_TTGO) and (CS_BUSY | CS_TTGO | CS_ODEVREADY) must be higher
183 * than the other bits so that they can be tested as a group without masking
186 * The following com and tty flags correspond closely:
187 * CS_BUSY = TS_BUSY (maintained by comstart(), siopoll() and
189 * CS_TTGO = ~TS_TTSTOP (maintained by comparam() and comstart())
190 * CS_CTS_OFLOW = CCTS_OFLOW (maintained by comparam())
191 * CS_RTS_IFLOW = CRTS_IFLOW (maintained by comparam())
192 * TS_FLUSH is not used.
193 * XXX I think TIOCSETA doesn't clear TS_TTSTOP when it clears IXON.
194 * XXX CS_*FLOW should be CF_*FLOW in com->flags (control flags not state).
196 #define CS_BUSY 0x80 /* output in progress */
197 #define CS_TTGO 0x40 /* output not stopped by XOFF */
198 #define CS_ODEVREADY 0x20 /* external device h/w ready (CTS) */
199 #define CS_CHECKMSR 1 /* check of MSR scheduled */
200 #define CS_CTS_OFLOW 2 /* use CTS output flow control */
201 #define CS_DTR_OFF 0x10 /* DTR held off */
202 #define CS_ODONE 4 /* output completed */
203 #define CS_RTS_IFLOW 8 /* use RTS input flow control */
204 #define CSE_ODONE 1 /* output transmitted */
206 static char const * const error_desc[] = {
209 #define CE_INTERRUPT_BUF_OVERFLOW 1
210 "interrupt-level buffer overflow",
211 #define CE_TTY_BUF_OVERFLOW 2
212 "tty-level buffer overflow",
216 #define CE_RECORD(com, errnum) (++(com)->delta_error_counts[errnum])
218 /* types. XXX - should be elsewhere */
219 typedef u_char bool_t; /* boolean */
220 typedef u_char volatile *cy_addr;
222 /* queue of linear buffers */
224 u_char *l_head; /* next char to process */
225 u_char *l_tail; /* one past the last char to process */
226 struct lbq *l_next; /* next in queue */
227 bool_t l_queued; /* nonzero if queued */
230 /* com device structure */
232 u_char state; /* miscellaneous flag bits */
233 bool_t active_out; /* nonzero if the callout device is open */
235 u_char cfcr_image; /* copy of value written to CFCR */
237 u_char etc; /* pending Embedded Transmit Command */
238 u_char extra_state; /* more flag bits, separate for order trick */
240 u_char fifo_image; /* copy of value written to FIFO */
242 u_char gfrcr_image; /* copy of value read from GFRCR */
244 bool_t hasfifo; /* nonzero for 16550 UARTs */
245 bool_t loses_outints; /* nonzero if device loses output interrupts */
247 u_char mcr_dtr; /* MCR bit that is wired to DTR */
248 u_char mcr_image; /* copy of value written to MCR */
249 u_char mcr_rts; /* MCR bit that is wired to RTS */
252 bool_t multiport; /* is this unit part of a multiport device? */
253 #endif /* COM_MULTIPORT */
254 bool_t no_irq; /* nonzero if irq is not attached */
255 bool_t poll; /* nonzero if polling is required */
256 bool_t poll_output; /* nonzero if polling for output is required */
258 int unit; /* unit number */
259 int dtr_wait; /* time to hold DTR down on close (* 1/hz) */
263 u_int wopeners; /* # processes waiting for DCD in open() */
266 * The high level of the driver never reads status registers directly
267 * because there would be too many side effects to handle conveniently.
268 * Instead, it reads copies of the registers stored here by the
271 u_char last_modem_status; /* last MSR read by intr handler */
272 u_char prev_modem_status; /* last MSR handled by high level */
274 u_char hotchar; /* ldisc-specific char to be handled ASAP */
275 u_char *ibuf; /* start of input buffer */
276 u_char *ibufend; /* end of input buffer */
277 u_char *ibufold; /* old input buffer, to be freed */
278 u_char *ihighwater; /* threshold in input buffer */
279 u_char *iptr; /* next free spot in input buffer */
280 int ibufsize; /* size of ibuf (not include error bytes) */
281 int ierroff; /* offset of error bytes in ibuf */
283 struct lbq obufq; /* head of queue of output buffers */
284 struct lbq obufs[2]; /* output buffers */
286 int cy_align; /* index for register alignment */
287 cy_addr cy_iobase; /* base address of this port's cyclom */
288 cy_addr iobase; /* base address of this port's cd1400 */
289 int mcr_rts_reg; /* cd1400 reg number of reg holding mcr_rts */
291 struct tty *tp; /* cross reference */
294 struct termios it_in; /* should be in struct tty */
295 struct termios it_out;
298 struct termios lt_in; /* should be in struct tty */
299 struct termios lt_out;
302 bool_t do_dcd_timestamp;
303 struct timeval timestamp;
304 struct timeval dcd_timestamp;
306 u_long bytes_in; /* statistics */
308 u_int delta_error_counts[CE_NTYPES];
309 u_long error_counts[CE_NTYPES];
311 u_int recv_exception; /* exception chars received */
312 u_int mdm; /* modem signal changes */
314 u_int start_count; /* no. of calls to comstart() */
315 u_int start_real; /* no. of calls that did something */
317 u_char car; /* CD1400 CAR shadow (if first unit in cd) */
318 u_char channel_control;/* CD1400 CCR control command shadow */
319 u_char cor[3]; /* CD1400 COR1-3 shadows */
320 u_char intr_enable; /* CD1400 SRER shadow */
323 * Data area for output buffers. Someday we should build the output
324 * buffer queue without copying data.
330 /* PCI driver entry point. */
331 int cyattach_common __P((cy_addr cy_iobase, int cy_align));
334 static int cy_units __P((cy_addr cy_iobase, int cy_align));
335 static int sioattach __P((struct isa_device *dev));
336 static void cd1400_channel_cmd __P((struct com_s *com, int cmd));
337 static void cd1400_channel_cmd_wait __P((struct com_s *com));
338 static void cd_etc __P((struct com_s *com, int etc));
339 static int cd_getreg __P((struct com_s *com, int reg));
340 static void cd_setreg __P((struct com_s *com, int reg, int val));
341 static timeout_t siodtrwakeup;
342 static void comhardclose __P((struct com_s *com));
343 static void sioinput __P((struct com_s *com));
345 static void siointr1 __P((struct com_s *com));
347 static int commctl __P((struct com_s *com, int bits, int how));
348 static int comparam __P((struct tty *tp, struct termios *t));
349 static swihand_t siopoll;
350 static int sioprobe __P((struct isa_device *dev));
351 static void siosettimeout __P((void));
352 static int siosetwater __P((struct com_s *com, speed_t speed));
353 static int comspeed __P((speed_t speed, u_long cy_clock,
355 static void comstart __P((struct tty *tp));
356 static void comstop __P((struct tty *tp, int rw));
357 static timeout_t comwakeup;
358 static void disc_optim __P((struct tty *tp, struct termios *t,
362 void cystatus __P((int unit));
365 static char driver_name[] = "cy";
367 /* table and macro for fast conversion from a unit number to its com struct */
368 static struct com_s *p_com_addr[NSIO];
369 #define com_addr(unit) (p_com_addr[unit])
371 struct isa_driver siodriver = {
372 sioprobe, sioattach, driver_name
375 static d_open_t sioopen;
376 static d_close_t sioclose;
377 static d_write_t siowrite;
378 static d_ioctl_t sioioctl;
380 #define CDEV_MAJOR 48
381 static struct cdevsw sio_cdevsw = {
383 /* close */ sioclose,
385 /* write */ siowrite,
386 /* ioctl */ sioioctl,
389 /* strategy */ nostrategy,
390 /* name */ driver_name,
391 /* maj */ CDEV_MAJOR,
394 /* flags */ D_TTY | D_KQFILTER,
396 /* kqfilter */ ttykqfilter,
399 static int comconsole = -1;
400 static speed_t comdefaultrate = TTYDEF_SPEED;
401 static u_int com_events; /* input chars + weighted output completions */
402 static bool_t sio_registered;
403 static int sio_timeout;
404 static int sio_timeouts_until_log;
405 static struct callout_handle sio_timeout_handle
406 = CALLOUT_HANDLE_INITIALIZER(&sio_timeout_handle);
408 static struct tty *sio_tty[NSIO];
410 static struct tty sio_tty[NSIO];
412 static const int nsio_tty = NSIO;
415 static u_int cd_inbs;
416 static u_int cy_inbs;
417 static u_int cd_outbs;
418 static u_int cy_outbs;
419 static u_int cy_svrr_probes;
420 static u_int cy_timeouts;
423 static int cy_chip_offset[] = {
424 0x0000, 0x0400, 0x0800, 0x0c00, 0x0200, 0x0600, 0x0a00, 0x0e00,
426 static int cy_nr_cd1400s[NCY];
427 static int cy_total_devices;
428 #undef RxFifoThreshold
429 static int volatile RxFifoThreshold = (CD1400_RX_FIFO_SIZE / 2);
433 struct isa_device *dev;
437 iobase = (cy_addr)dev->id_maddr;
439 /* Cyclom-16Y hardware reset (Cyclom-8Ys don't care) */
440 cy_inb(iobase, CY16_RESET, 0); /* XXX? */
441 DELAY(500); /* wait for the board to get its act together */
443 /* this is needed to get the board out of reset */
444 cy_outb(iobase, CY_CLEAR_INTR, 0, 0);
447 return (cy_units(iobase, 0) == 0 ? 0 : -1);
451 cy_units(cy_iobase, cy_align)
456 u_char firmware_version;
460 for (cyu = 0; cyu < CY_MAX_CD1400s; ++cyu) {
461 iobase = cy_iobase + (cy_chip_offset[cyu] << cy_align);
463 /* wait for chip to become ready for new command */
464 for (i = 0; i < 10; i++) {
466 if (!cd_inb(iobase, CD1400_CCR, cy_align))
470 /* clear the GFRCR register */
471 cd_outb(iobase, CD1400_GFRCR, cy_align, 0);
473 /* issue a reset command */
474 cd_outb(iobase, CD1400_CCR, cy_align,
475 CD1400_CCR_CMDRESET | CD1400_CCR_FULLRESET);
477 /* wait for the CD1400 to initialize itself */
478 for (i = 0; i < 200; i++) {
481 /* retrieve firmware version */
482 firmware_version = cd_inb(iobase, CD1400_GFRCR,
484 if ((firmware_version & 0xf0) == 0x40)
489 * Anything in the 0x40-0x4F range is fine.
490 * If one CD1400 is bad then we don't support higher
491 * numbered good ones on this board.
493 if ((firmware_version & 0xf0) != 0x40)
501 struct isa_device *isdp;
505 adapter = cyattach_common((cy_addr) isdp->id_maddr, 0);
511 * This kludge is to allow ISA/PCI device specifications in the
512 * kernel config file to be in any order.
514 if (isdp->id_unit != adapter) {
515 printf("cy%d: attached as cy%d\n", isdp->id_unit, adapter);
516 isdp->id_unit = adapter; /* XXX */
518 isdp->id_ointr = siointr;
519 /* isdp->id_ri_flags |= RI_FAST; XXX unimplemented - use newbus! */
524 cyattach_common(cy_iobase, cy_align)
530 u_char firmware_version;
536 adapter = cy_total_devices;
537 if ((u_int)adapter >= NCY) {
539 "cy%d: can't attach adapter: insufficient cy devices configured\n",
543 ncyu = cy_units(cy_iobase, cy_align);
546 cy_nr_cd1400s[adapter] = ncyu;
549 unit = adapter * CY_MAX_PORTS;
550 for (cyu = 0; cyu < ncyu; ++cyu) {
553 iobase = (cy_addr) (cy_iobase
554 + (cy_chip_offset[cyu] << cy_align));
555 firmware_version = cd_inb(iobase, CD1400_GFRCR, cy_align);
557 /* Set up a receive timeout period of than 1+ ms. */
558 cd_outb(iobase, CD1400_PPR, cy_align,
559 howmany(CY_CLOCK(firmware_version)
560 / CD1400_PPR_PRESCALER, 1000));
562 for (cdu = 0; cdu < CD1400_NO_OF_CHANNELS; ++cdu, ++unit) {
566 com = malloc(sizeof *com, M_DEVBUF, M_NOWAIT);
569 bzero(com, sizeof *com);
571 com->gfrcr_image = firmware_version;
572 if (CY_RTS_DTR_SWAPPED(firmware_version)) {
573 com->mcr_dtr = MCR_RTS;
574 com->mcr_rts = MCR_DTR;
575 com->mcr_rts_reg = CD1400_MSVR2;
577 com->mcr_dtr = MCR_DTR;
578 com->mcr_rts = MCR_RTS;
579 com->mcr_rts_reg = CD1400_MSVR1;
581 com->dtr_wait = 3 * hz;
582 com->obufs[0].l_head = com->obuf1;
583 com->obufs[1].l_head = com->obuf2;
585 com->cy_align = cy_align;
586 com->cy_iobase = cy_iobase;
587 com->iobase = iobase;
588 com->car = ~CD1400_CAR_CHAN;
591 * We don't use all the flags from <sys/ttydefaults.h> since they
592 * are only relevant for logins. It's important to have echo off
593 * initially so that the line doesn't start blathering before the
594 * echo flag can be turned off.
596 com->it_in.c_iflag = 0;
597 com->it_in.c_oflag = 0;
598 com->it_in.c_cflag = TTYDEF_CFLAG;
599 com->it_in.c_lflag = 0;
600 if (unit == comconsole) {
601 com->it_in.c_iflag = TTYDEF_IFLAG;
602 com->it_in.c_oflag = TTYDEF_OFLAG;
603 com->it_in.c_cflag = TTYDEF_CFLAG | CLOCAL;
604 com->it_in.c_lflag = TTYDEF_LFLAG;
605 com->lt_out.c_cflag = com->lt_in.c_cflag = CLOCAL;
607 if (siosetwater(com, com->it_in.c_ispeed) != 0) {
613 termioschars(&com->it_in);
614 com->it_in.c_ispeed = com->it_in.c_ospeed = comdefaultrate;
615 com->it_out = com->it_in;
618 com_addr(unit) = com;
621 if (!sio_registered) {
622 cdevsw_add(&sio_cdevsw);
623 register_swi(SWI_TTY, siopoll);
624 sio_registered = TRUE;
626 minorbase = UNIT_TO_MINOR(unit);
627 make_dev(&sio_cdevsw, minorbase,
628 UID_ROOT, GID_WHEEL, 0600, "ttyc%r%r", adapter,
629 unit % CY_MAX_PORTS);
630 make_dev(&sio_cdevsw, minorbase | CONTROL_INIT_STATE,
631 UID_ROOT, GID_WHEEL, 0600, "ttyic%r%r", adapter,
632 unit % CY_MAX_PORTS);
633 make_dev(&sio_cdevsw, minorbase | CONTROL_LOCK_STATE,
634 UID_ROOT, GID_WHEEL, 0600, "ttylc%r%r", adapter,
635 unit % CY_MAX_PORTS);
636 make_dev(&sio_cdevsw, minorbase | CALLOUT_MASK,
637 UID_UUCP, GID_DIALER, 0660, "cuac%r%r", adapter,
638 unit % CY_MAX_PORTS);
639 make_dev(&sio_cdevsw, minorbase | CALLOUT_MASK | CONTROL_INIT_STATE,
640 UID_UUCP, GID_DIALER, 0660, "cuaic%r%r", adapter,
641 unit % CY_MAX_PORTS);
642 make_dev(&sio_cdevsw, minorbase | CALLOUT_MASK | CONTROL_LOCK_STATE,
643 UID_UUCP, GID_DIALER, 0660, "cualc%r%r", adapter,
644 unit % CY_MAX_PORTS);
648 /* ensure an edge for the next interrupt */
649 cy_outb(cy_iobase, CY_CLEAR_INTR, cy_align, 0);
655 sioopen(dev_t dev; int flag; int mode; struct thread *td)
665 unit = MINOR_TO_UNIT(mynor);
666 if ((u_int) unit >= NSIO || (com = com_addr(unit)) == NULL)
668 if (mynor & CONTROL_MASK)
671 tp = com->tp = sio_tty[unit] = ttymalloc(sio_tty[unit]);
673 tp = com->tp = &sio_tty[unit];
678 * We jump to this label after all non-interrupted sleeps to pick
679 * up any changes of the device state.
682 while (com->state & CS_DTR_OFF) {
683 error = tsleep(&com->dtr_wait, PCATCH, "cydtr", 0);
687 if (tp->t_state & TS_ISOPEN) {
689 * The device is open, so everything has been initialized.
692 if (mynor & CALLOUT_MASK) {
693 if (!com->active_out) {
698 if (com->active_out) {
699 if (flag & O_NONBLOCK) {
703 error = tsleep(&com->active_out,
710 if (tp->t_state & TS_XCLUDE &&
717 * The device isn't open, so there are no conflicts.
718 * Initialize it. Initialization is done twice in many
719 * cases: to preempt sleeping callin opens if we are
720 * callout, and to complete a callin open after DCD rises.
722 tp->t_oproc = comstart;
723 tp->t_stop = comstop;
724 tp->t_param = comparam;
726 tp->t_termios = mynor & CALLOUT_MASK
727 ? com->it_out : com->it_in;
729 /* Encode per-board unit in LIVR for access in intr routines. */
730 cd_setreg(com, CD1400_LIVR,
731 (unit & CD1400_xIVR_CHAN) << CD1400_xIVR_CHAN_SHIFT);
733 (void)commctl(com, TIOCM_DTR | TIOCM_RTS, DMSET);
735 com->poll = com->no_irq;
736 com->poll_output = com->loses_outints;
739 error = comparam(tp, &tp->t_termios);
746 * (Re)enable and flush fifos.
748 * Certain SMC chips cause problems if the fifos
749 * are enabled while input is ready. Turn off the
750 * fifo if necessary to clear the input. We test
751 * the input ready bit after enabling the fifos
752 * since we've already enabled them in comparam()
753 * and to handle races between enabling and fresh
757 outb(iobase + com_fifo,
758 FIFO_RCV_RST | FIFO_XMT_RST
761 if (!(inb(com->line_status_port) & LSR_RXRDY))
763 outb(iobase + com_fifo, 0);
765 (void) inb(com->data_port);
770 (void) inb(com->line_status_port);
771 (void) inb(com->data_port);
772 com->prev_modem_status = com->last_modem_status
773 = inb(com->modem_status_port);
774 outb(iobase + com_ier, IER_ERXRDY | IER_ETXRDY | IER_ERLS
779 * Flush fifos. This requires a full channel reset which
780 * also disables the transmitter and receiver. Recover
783 cd1400_channel_cmd(com,
784 CD1400_CCR_CMDRESET | CD1400_CCR_CHANRESET);
785 cd1400_channel_cmd(com, com->channel_control);
788 com->prev_modem_status = com->last_modem_status
789 = cd_getreg(com, CD1400_MSVR2);
790 cd_setreg(com, CD1400_SRER,
792 = CD1400_SRER_MDMCH | CD1400_SRER_RXDATA);
796 * Handle initial DCD. Callout devices get a fake initial
797 * DCD (trapdoor DCD). If we are callout, then any sleeping
798 * callin opens get woken up and resume sleeping on "cybi"
799 * instead of "cydcd".
802 * XXX `mynor & CALLOUT_MASK' should be
803 * `tp->t_cflag & (SOFT_CARRIER | TRAPDOOR_CARRIER) where
804 * TRAPDOOR_CARRIER is the default initial state for callout
805 * devices and SOFT_CARRIER is like CLOCAL except it hides
808 if (com->prev_modem_status & MSR_DCD || mynor & CALLOUT_MASK)
809 (*linesw[tp->t_line].l_modem)(tp, 1);
812 * Wait for DCD if necessary.
814 if (!(tp->t_state & TS_CARR_ON) && !(mynor & CALLOUT_MASK)
815 && !(tp->t_cflag & CLOCAL) && !(flag & O_NONBLOCK)) {
817 error = tsleep(TSA_CARR_ON(tp), PCATCH, "cydcd", 0);
823 error = (*linesw[tp->t_line].l_open)(dev, tp);
824 disc_optim(tp, &tp->t_termios, com);
825 if (tp->t_state & TS_ISOPEN && mynor & CALLOUT_MASK)
826 com->active_out = TRUE;
830 if (!(tp->t_state & TS_ISOPEN) && com->wopeners == 0)
836 sioclose(dev_t dev, int flag, int mode, struct thread *td)
844 if (mynor & CONTROL_MASK)
846 com = com_addr(MINOR_TO_UNIT(mynor));
849 cd_etc(com, CD1400_ETC_STOPBREAK);
850 (*linesw[tp->t_line].l_close)(tp, flag);
851 disc_optim(tp, &tp->t_termios, com);
852 comstop(tp, FREAD | FWRITE);
857 #ifdef broken /* session holds a ref to the tty; can't deallocate */
859 com->tp = sio_tty[unit] = NULL;
874 iobase = com->iobase;
878 com->poll_output = FALSE;
880 com->do_timestamp = 0;
882 outb(iobase + com_cfcr, com->cfcr_image &= ~CFCR_SBREAK);
887 cd_setreg(com, CD1400_COR2, com->cor[1] &= ~CD1400_COR2_ETC);
889 cd1400_channel_cmd(com, CD1400_CCR_CMDRESET | CD1400_CCR_FTF);
894 outb(iobase + com_ier, 0);
897 cd_setreg(com, CD1400_SRER, com->intr_enable = 0);
901 if ((tp->t_cflag & HUPCL)
903 * XXX we will miss any carrier drop between here and the
904 * next open. Perhaps we should watch DCD even when the
905 * port is closed; it is not sufficient to check it at
906 * the next open because it might go up and down while
907 * we're not watching.
910 && !(com->prev_modem_status & MSR_DCD)
911 && !(com->it_in.c_cflag & CLOCAL))
912 || !(tp->t_state & TS_ISOPEN)) {
913 (void)commctl(com, TIOCM_DTR, DMBIC);
915 /* Disable receiver (leave transmitter enabled). */
916 com->channel_control = CD1400_CCR_CMDCHANCTL
919 cd1400_channel_cmd(com, com->channel_control);
921 if (com->dtr_wait != 0 && !(com->state & CS_DTR_OFF)) {
922 timeout(siodtrwakeup, com, com->dtr_wait);
923 com->state |= CS_DTR_OFF;
930 * Disable fifos so that they are off after controlled
931 * reboots. Some BIOSes fail to detect 16550s when the
934 outb(iobase + com_fifo, 0);
937 com->active_out = FALSE;
938 wakeup(&com->active_out);
939 wakeup(TSA_CARR_ON(tp)); /* restart any wopeners */
944 siowrite(dev, uio, flag)
954 if (mynor & CONTROL_MASK)
957 unit = MINOR_TO_UNIT(mynor);
958 tp = com_addr(unit)->tp;
960 * (XXX) We disallow virtual consoles if the physical console is
961 * a serial port. This is in case there is a display attached that
962 * is not the console. In that situation we don't need/want the X
963 * server taking over the console.
965 if (constty != NULL && unit == comconsole)
968 /* XXX duplicate ttwrite(), but without so much output processing on
969 * CR & LF chars. Hardly worth the effort, given that high-throughput
970 * sessions are raw anyhow.
973 return ((*linesw[tp->t_line].l_write)(tp, uio, flag));
983 com = (struct com_s *)chan;
984 com->state &= ~CS_DTR_OFF;
985 wakeup(&com->dtr_wait);
1000 if (!(tp->t_state & TS_ISOPEN)) {
1001 com_events -= (com->iptr - com->ibuf);
1002 com->iptr = com->ibuf;
1005 if (tp->t_state & TS_CAN_BYPASS_L_RINT) {
1007 * Avoid the grotesquely inefficient lineswitch routine
1008 * (ttyinput) in "raw" mode. It usually takes about 450
1009 * instructions (that's without canonical processing or echo!).
1010 * slinput is reasonably fast (usually 40 instructions plus
1015 incc = com->iptr - buf;
1016 if (tp->t_rawq.c_cc + incc > tp->t_ihiwat
1017 && (com->state & CS_RTS_IFLOW
1018 || tp->t_iflag & IXOFF)
1019 && !(tp->t_state & TS_TBLOCK))
1021 com->delta_error_counts[CE_TTY_BUF_OVERFLOW]
1022 += b_to_q((char *)buf, incc, &tp->t_rawq);
1026 tp->t_rawcc += incc;
1028 if (tp->t_state & TS_TTSTOP
1029 && (tp->t_iflag & IXANY
1030 || tp->t_cc[VSTART] == tp->t_cc[VSTOP])) {
1031 tp->t_state &= ~TS_TTSTOP;
1032 tp->t_lflag &= ~FLUSHO;
1036 } while (buf < com->iptr);
1040 line_status = buf[com->ierroff];
1043 & (LSR_BI | LSR_FE | LSR_OE | LSR_PE)) {
1044 if (line_status & LSR_BI)
1045 recv_data |= TTY_BI;
1046 if (line_status & LSR_FE)
1047 recv_data |= TTY_FE;
1048 if (line_status & LSR_OE)
1049 recv_data |= TTY_OE;
1050 if (line_status & LSR_PE)
1051 recv_data |= TTY_PE;
1053 (*linesw[tp->t_line].l_rint)(recv_data, tp);
1055 } while (buf < com->iptr);
1057 com_events -= (com->iptr - com->ibuf);
1058 com->iptr = com->ibuf;
1061 * There is now room for another low-level buffer full of input,
1062 * so enable RTS if it is now disabled and there is room in the
1063 * high-level buffer.
1065 if ((com->state & CS_RTS_IFLOW) && !(com->mcr_image & com->mcr_rts) &&
1066 !(tp->t_state & TS_TBLOCK))
1068 outb(com->modem_ctl_port, com->mcr_image |= MCR_RTS);
1070 cd_setreg(com, com->mcr_rts_reg,
1071 com->mcr_image |= com->mcr_rts);
1086 COM_LOCK(); /* XXX could this be placed down lower in the loop? */
1088 baseu = unit * CY_MAX_PORTS;
1089 cy_align = com_addr(baseu)->cy_align;
1090 cy_iobase = com_addr(baseu)->cy_iobase;
1092 /* check each CD1400 in turn */
1093 for (cyu = 0; cyu < cy_nr_cd1400s[unit]; ++cyu) {
1094 iobase = (cy_addr) (cy_iobase
1095 + (cy_chip_offset[cyu] << cy_align));
1096 /* poll to see if it has any work */
1097 status = cd_inb(iobase, CD1400_SVRR, cy_align);
1103 /* service requests as appropriate, giving priority to RX */
1104 if (status & CD1400_SVRR_RXRDY) {
1116 save_rir = cd_inb(iobase, CD1400_RIR, cy_align);
1118 /* enter rx service */
1119 cd_outb(iobase, CD1400_CAR, cy_align, save_rir);
1120 com_addr(baseu + cyu * CD1400_NO_OF_CHANNELS)->car
1121 = save_rir & CD1400_CAR_CHAN;
1123 serv_type = cd_inb(iobase, CD1400_RIVR, cy_align);
1124 com = com_addr(baseu
1125 + ((serv_type >> CD1400_xIVR_CHAN_SHIFT)
1126 & CD1400_xIVR_CHAN));
1128 /* ack receive service */
1129 serv_type = cy_inb(iobase, CY8_SVCACKR, cy_align);
1131 com = com_addr(baseu +
1132 + ((serv_type >> CD1400_xIVR_CHAN_SHIFT)
1133 & CD1400_xIVR_CHAN));
1136 if (serv_type & CD1400_RIVR_EXCEPTION) {
1137 ++com->recv_exception;
1138 line_status = cd_inb(iobase, CD1400_RDSR, cy_align);
1139 /* break/unnattached error bits or real input? */
1140 recv_data = cd_inb(iobase, CD1400_RDSR, cy_align);
1141 #ifndef SOFT_HOTCHAR
1142 if (line_status & CD1400_RDSR_SPECIAL
1143 && com->hotchar != 0)
1146 #if 1 /* XXX "intelligent" PFO error handling would break O error handling */
1147 if (line_status & (LSR_PE|LSR_FE|LSR_BI)) {
1149 Don't store PE if IGNPAR and BI if IGNBRK,
1150 this hack allows "raw" tty optimization
1151 works even if IGN* is set.
1153 if ( com->tp == NULL
1154 || !(com->tp->t_state & TS_ISOPEN)
1155 || ((line_status & (LSR_PE|LSR_FE))
1156 && (com->tp->t_iflag & IGNPAR))
1157 || ((line_status & LSR_BI)
1158 && (com->tp->t_iflag & IGNBRK)))
1160 if ( (line_status & (LSR_PE|LSR_FE))
1161 && (com->tp->t_state & TS_CAN_BYPASS_L_RINT)
1162 && ((line_status & LSR_FE)
1163 || ((line_status & LSR_PE)
1164 && (com->tp->t_iflag & INPCK))))
1170 if (com->hotchar != 0 && recv_data == com->hotchar)
1174 if (ioptr >= com->ibufend)
1175 CE_RECORD(com, CE_INTERRUPT_BUF_OVERFLOW);
1177 if (com->do_timestamp)
1178 microtime(&com->timestamp);
1180 ioptr[0] = recv_data;
1181 ioptr[com->ierroff] = line_status;
1182 com->iptr = ++ioptr;
1183 if (ioptr == com->ihighwater
1184 && com->state & CS_RTS_IFLOW)
1186 outb(com->modem_ctl_port,
1187 com->mcr_image &= ~MCR_RTS);
1189 cd_outb(iobase, com->mcr_rts_reg,
1194 if (line_status & LSR_OE)
1195 CE_RECORD(com, CE_OVERRUN);
1201 count = cd_inb(iobase, CD1400_RDCR, cy_align);
1204 com->bytes_in += count;
1206 ifree = com->ibufend - ioptr;
1207 if (count > ifree) {
1209 com_events += ifree;
1211 if (com->do_timestamp)
1212 microtime(&com->timestamp);
1214 recv_data = cd_inb(iobase,
1218 if (com->hotchar != 0
1223 ioptr[0] = recv_data;
1224 ioptr[com->ierroff] = 0;
1226 } while (--ifree != 0);
1228 com->delta_error_counts
1229 [CE_INTERRUPT_BUF_OVERFLOW] += count;
1231 recv_data = cd_inb(iobase, CD1400_RDSR,
1234 if (com->hotchar != 0
1235 && recv_data == com->hotchar)
1238 } while (--count != 0);
1240 if (com->do_timestamp)
1241 microtime(&com->timestamp);
1242 if (ioptr <= com->ihighwater
1243 && ioptr + count > com->ihighwater
1244 && com->state & CS_RTS_IFLOW)
1246 outb(com->modem_ctl_port,
1247 com->mcr_image &= ~MCR_RTS);
1249 cd_outb(iobase, com->mcr_rts_reg,
1254 com_events += count;
1256 recv_data = cd_inb(iobase, CD1400_RDSR,
1259 if (com->hotchar != 0
1260 && recv_data == com->hotchar)
1263 ioptr[0] = recv_data;
1264 ioptr[com->ierroff] = 0;
1266 } while (--count != 0);
1272 /* terminate service context */
1274 cd_outb(iobase, CD1400_RIR, cy_align,
1276 & ~(CD1400_RIR_RDIREQ | CD1400_RIR_RBUSY));
1278 cd_outb(iobase, CD1400_EOSRR, cy_align, 0);
1281 if (status & CD1400_SVRR_MDMCH) {
1283 u_char modem_status;
1291 save_mir = cd_inb(iobase, CD1400_MIR, cy_align);
1293 /* enter modem service */
1294 cd_outb(iobase, CD1400_CAR, cy_align, save_mir);
1295 com_addr(baseu + cyu * CD1400_NO_OF_CHANNELS)->car
1296 = save_mir & CD1400_CAR_CHAN;
1298 com = com_addr(baseu + cyu * CD1400_NO_OF_CHANNELS
1299 + (save_mir & CD1400_MIR_CHAN));
1301 /* ack modem service */
1302 vector = cy_inb(iobase, CY8_SVCACKM, cy_align);
1304 com = com_addr(baseu
1305 + ((vector >> CD1400_xIVR_CHAN_SHIFT)
1306 & CD1400_xIVR_CHAN));
1309 modem_status = cd_inb(iobase, CD1400_MSVR2, cy_align);
1310 if (modem_status != com->last_modem_status) {
1311 if (com->do_dcd_timestamp
1312 && !(com->last_modem_status & MSR_DCD)
1313 && modem_status & MSR_DCD)
1314 microtime(&com->dcd_timestamp);
1317 * Schedule high level to handle DCD changes. Note
1318 * that we don't use the delta bits anywhere. Some
1319 * UARTs mess them up, and it's easy to remember the
1320 * previous bits and calculate the delta.
1322 com->last_modem_status = modem_status;
1323 if (!(com->state & CS_CHECKMSR)) {
1324 com_events += LOTS_OF_EVENTS;
1325 com->state |= CS_CHECKMSR;
1329 #ifdef SOFT_CTS_OFLOW
1330 /* handle CTS change immediately for crisp flow ctl */
1331 if (com->state & CS_CTS_OFLOW) {
1332 if (modem_status & MSR_CTS) {
1333 com->state |= CS_ODEVREADY;
1334 if (com->state >= (CS_BUSY | CS_TTGO
1336 && !(com->intr_enable
1337 & CD1400_SRER_TXRDY))
1338 cd_outb(iobase, CD1400_SRER,
1342 & ~CD1400_SRER_TXMPTY
1343 | CD1400_SRER_TXRDY);
1345 com->state &= ~CS_ODEVREADY;
1346 if (com->intr_enable
1347 & CD1400_SRER_TXRDY)
1348 cd_outb(iobase, CD1400_SRER,
1352 & ~CD1400_SRER_TXRDY
1353 | CD1400_SRER_TXMPTY);
1359 /* terminate service context */
1361 cd_outb(iobase, CD1400_MIR, cy_align,
1363 & ~(CD1400_MIR_RDIREQ | CD1400_MIR_RBUSY));
1365 cd_outb(iobase, CD1400_EOSRR, cy_align, 0);
1368 if (status & CD1400_SVRR_TXRDY) {
1377 save_tir = cd_inb(iobase, CD1400_TIR, cy_align);
1379 /* enter tx service */
1380 cd_outb(iobase, CD1400_CAR, cy_align, save_tir);
1381 com_addr(baseu + cyu * CD1400_NO_OF_CHANNELS)->car
1382 = save_tir & CD1400_CAR_CHAN;
1384 com = com_addr(baseu
1385 + cyu * CD1400_NO_OF_CHANNELS
1386 + (save_tir & CD1400_TIR_CHAN));
1388 /* ack transmit service */
1389 vector = cy_inb(iobase, CY8_SVCACKT, cy_align);
1391 com = com_addr(baseu
1392 + ((vector >> CD1400_xIVR_CHAN_SHIFT)
1393 & CD1400_xIVR_CHAN));
1396 if (com->etc != ETC_NONE) {
1397 if (com->intr_enable & CD1400_SRER_TXRDY) {
1399 * Here due to sloppy SRER_TXRDY
1400 * enabling. Ignore. Come back when
1403 cd_outb(iobase, CD1400_SRER, cy_align,
1406 & ~CD1400_SRER_TXRDY)
1407 | CD1400_SRER_TXMPTY);
1408 goto terminate_tx_service;
1411 case CD1400_ETC_SENDBREAK:
1412 case CD1400_ETC_STOPBREAK:
1414 * Start the command. Come back on
1415 * next tx empty interrupt, hopefully
1416 * after command has been executed.
1418 cd_outb(iobase, CD1400_COR2, cy_align,
1419 com->cor[1] |= CD1400_COR2_ETC);
1420 cd_outb(iobase, CD1400_TDR, cy_align,
1422 cd_outb(iobase, CD1400_TDR, cy_align,
1424 if (com->etc == CD1400_ETC_SENDBREAK)
1425 com->etc = ETC_BREAK_STARTING;
1427 com->etc = ETC_BREAK_ENDING;
1428 goto terminate_tx_service;
1429 case ETC_BREAK_STARTING:
1431 * BREAK is now on. Continue with
1432 * SRER_TXMPTY processing, hopefully
1435 com->etc = ETC_BREAK_STARTED;
1437 case ETC_BREAK_STARTED:
1439 * Came back due to sloppy SRER_TXMPTY
1440 * enabling. Hope again.
1443 case ETC_BREAK_ENDING:
1445 * BREAK is now off. Continue with
1446 * SRER_TXMPTY processing and don't
1447 * come back. The SWI handler will
1448 * restart tx interrupts if necessary.
1450 cd_outb(iobase, CD1400_COR2, cy_align,
1452 &= ~CD1400_COR2_ETC);
1453 com->etc = ETC_BREAK_ENDED;
1454 if (!(com->state & CS_ODONE)) {
1455 com_events += LOTS_OF_EVENTS;
1456 com->state |= CS_ODONE;
1460 case ETC_BREAK_ENDED:
1462 * Shouldn't get here. Hope again.
1467 if (com->intr_enable & CD1400_SRER_TXMPTY) {
1468 if (!(com->extra_state & CSE_ODONE)) {
1469 com_events += LOTS_OF_EVENTS;
1470 com->extra_state |= CSE_ODONE;
1473 cd_outb(iobase, CD1400_SRER, cy_align,
1475 &= ~CD1400_SRER_TXMPTY);
1476 goto terminate_tx_service;
1478 if (com->state >= (CS_BUSY | CS_TTGO | CS_ODEVREADY)) {
1482 ioptr = com->obufq.l_head;
1483 ocount = com->obufq.l_tail - ioptr;
1484 if (ocount > CD1400_TX_FIFO_SIZE)
1485 ocount = CD1400_TX_FIFO_SIZE;
1486 com->bytes_out += ocount;
1488 cd_outb(iobase, CD1400_TDR, cy_align,
1490 while (--ocount != 0);
1491 com->obufq.l_head = ioptr;
1492 if (ioptr >= com->obufq.l_tail) {
1495 qp = com->obufq.l_next;
1496 qp->l_queued = FALSE;
1499 com->obufq.l_head = qp->l_head;
1500 com->obufq.l_tail = qp->l_tail;
1501 com->obufq.l_next = qp;
1503 /* output just completed */
1504 com->state &= ~CS_BUSY;
1507 * The setting of CSE_ODONE may be
1508 * stale here. We currently only
1509 * use it when CS_BUSY is set, and
1510 * fixing it when we clear CS_BUSY
1513 if (com->extra_state & CSE_ODONE) {
1514 com_events -= LOTS_OF_EVENTS;
1515 com->extra_state &= ~CSE_ODONE;
1518 cd_outb(iobase, CD1400_SRER, cy_align,
1521 & ~CD1400_SRER_TXRDY)
1522 | CD1400_SRER_TXMPTY);
1524 if (!(com->state & CS_ODONE)) {
1525 com_events += LOTS_OF_EVENTS;
1526 com->state |= CS_ODONE;
1528 /* handle at high level ASAP */
1534 /* terminate service context */
1535 terminate_tx_service:
1537 cd_outb(iobase, CD1400_TIR, cy_align,
1539 & ~(CD1400_TIR_RDIREQ | CD1400_TIR_RBUSY));
1541 cd_outb(iobase, CD1400_EOSRR, cy_align, 0);
1546 /* ensure an edge for the next interrupt */
1547 cy_outb(cy_iobase, CY_CLEAR_INTR, cy_align, 0);
1563 sioioctl(dev_t dev, u_long cmd, caddr_t data, int flag, struct thread *td)
1570 #if defined(COMPAT_43) || defined(COMPAT_SUNOS)
1572 struct termios term;
1576 com = com_addr(MINOR_TO_UNIT(mynor));
1577 if (mynor & CONTROL_MASK) {
1580 switch (mynor & CONTROL_MASK) {
1581 case CONTROL_INIT_STATE:
1582 ct = mynor & CALLOUT_MASK ? &com->it_out : &com->it_in;
1584 case CONTROL_LOCK_STATE:
1585 ct = mynor & CALLOUT_MASK ? &com->lt_out : &com->lt_in;
1588 return (ENODEV); /* /dev/nodev */
1595 *ct = *(struct termios *)data;
1598 *(struct termios *)data = *ct;
1601 *(int *)data = TTYDISC;
1604 bzero(data, sizeof(struct winsize));
1611 #if defined(COMPAT_43) || defined(COMPAT_SUNOS)
1612 term = tp->t_termios;
1614 error = ttsetcompat(tp, &cmd, data, &term);
1618 data = (caddr_t)&term;
1620 if (cmd == TIOCSETA || cmd == TIOCSETAW || cmd == TIOCSETAF) {
1622 struct termios *dt = (struct termios *)data;
1623 struct termios *lt = mynor & CALLOUT_MASK
1624 ? &com->lt_out : &com->lt_in;
1626 dt->c_iflag = (tp->t_iflag & lt->c_iflag)
1627 | (dt->c_iflag & ~lt->c_iflag);
1628 dt->c_oflag = (tp->t_oflag & lt->c_oflag)
1629 | (dt->c_oflag & ~lt->c_oflag);
1630 dt->c_cflag = (tp->t_cflag & lt->c_cflag)
1631 | (dt->c_cflag & ~lt->c_cflag);
1632 dt->c_lflag = (tp->t_lflag & lt->c_lflag)
1633 | (dt->c_lflag & ~lt->c_lflag);
1634 for (cc = 0; cc < NCCS; ++cc)
1635 if (lt->c_cc[cc] != 0)
1636 dt->c_cc[cc] = tp->t_cc[cc];
1637 if (lt->c_ispeed != 0)
1638 dt->c_ispeed = tp->t_ispeed;
1639 if (lt->c_ospeed != 0)
1640 dt->c_ospeed = tp->t_ospeed;
1642 error = (*linesw[tp->t_line].l_ioctl)(tp, cmd, data, flag, p);
1643 if (error != ENOIOCTL)
1646 error = ttioctl(tp, cmd, data, flag);
1647 disc_optim(tp, &tp->t_termios, com);
1648 if (error != ENOIOCTL) {
1655 outb(iobase + com_cfcr, com->cfcr_image |= CFCR_SBREAK);
1657 cd_etc(com, CD1400_ETC_SENDBREAK);
1662 outb(iobase + com_cfcr, com->cfcr_image &= ~CFCR_SBREAK);
1664 cd_etc(com, CD1400_ETC_STOPBREAK);
1668 (void)commctl(com, TIOCM_DTR, DMBIS);
1671 (void)commctl(com, TIOCM_DTR, DMBIC);
1674 * XXX should disallow changing MCR_RTS if CS_RTS_IFLOW is set. The
1675 * changes get undone on the next call to comparam().
1678 (void)commctl(com, *(int *)data, DMSET);
1681 (void)commctl(com, *(int *)data, DMBIS);
1684 (void)commctl(com, *(int *)data, DMBIC);
1687 *(int *)data = commctl(com, 0, DMGET);
1690 /* must be root since the wait applies to following logins */
1696 com->dtr_wait = *(int *)data * hz / 100;
1699 *(int *)data = com->dtr_wait * 100 / hz;
1702 com->do_timestamp = TRUE;
1703 *(struct timeval *)data = com->timestamp;
1705 case TIOCDCDTIMESTAMP:
1706 com->do_dcd_timestamp = TRUE;
1707 *(struct timeval *)data = com->dcd_timestamp;
1725 if (com_events == 0)
1728 for (unit = 0; unit < NSIO; ++unit) {
1733 com = com_addr(unit);
1739 * XXX forget any events related to closed devices
1740 * (actually never opened devices) so that we don't
1744 incc = com->iptr - com->ibuf;
1745 com->iptr = com->ibuf;
1746 if (com->state & CS_CHECKMSR) {
1747 incc += LOTS_OF_EVENTS;
1748 com->state &= ~CS_CHECKMSR;
1754 "sio%d: %d events for device with no tp\n",
1758 if (com->iptr != com->ibuf) {
1763 if (com->state & CS_CHECKMSR) {
1764 u_char delta_modem_status;
1767 delta_modem_status = com->last_modem_status
1768 ^ com->prev_modem_status;
1769 com->prev_modem_status = com->last_modem_status;
1770 com_events -= LOTS_OF_EVENTS;
1771 com->state &= ~CS_CHECKMSR;
1773 if (delta_modem_status & MSR_DCD)
1774 (*linesw[tp->t_line].l_modem)
1775 (tp, com->prev_modem_status & MSR_DCD);
1777 if (com->extra_state & CSE_ODONE) {
1779 com_events -= LOTS_OF_EVENTS;
1780 com->extra_state &= ~CSE_ODONE;
1782 if (!(com->state & CS_BUSY)) {
1783 tp->t_state &= ~TS_BUSY;
1786 if (com->etc != ETC_NONE) {
1787 if (com->etc == ETC_BREAK_ENDED)
1788 com->etc = ETC_NONE;
1792 if (com->state & CS_ODONE) {
1794 com_events -= LOTS_OF_EVENTS;
1795 com->state &= ~CS_ODONE;
1797 (*linesw[tp->t_line].l_start)(tp);
1799 if (com_events == 0)
1802 if (com_events >= LOTS_OF_EVENTS)
1826 /* do historical conversions */
1827 if (t->c_ispeed == 0)
1828 t->c_ispeed = t->c_ospeed;
1830 unit = DEV_TO_UNIT(tp->t_dev);
1831 com = com_addr(unit);
1833 /* check requested parameters */
1834 cy_clock = CY_CLOCK(com->gfrcr_image);
1835 idivisor = comspeed(t->c_ispeed, cy_clock, &iprescaler);
1838 odivisor = comspeed(t->c_ospeed, cy_clock, &oprescaler);
1842 /* parameters are OK, convert them to the com struct and the device */
1845 (void)commctl(com, TIOCM_DTR, DMBIC); /* hang up line */
1847 (void)commctl(com, TIOCM_DTR, DMBIS);
1850 * This returns with interrupts disabled so that we can complete
1851 * the speed change atomically.
1853 (void) siosetwater(com, t->c_ispeed);
1855 /* XXX we don't actually change the speed atomically. */
1858 if (idivisor != 0) {
1859 cd_setreg(com, CD1400_RBPR, idivisor);
1860 cd_setreg(com, CD1400_RCOR, iprescaler);
1862 if (odivisor != 0) {
1863 cd_setreg(com, CD1400_TBPR, odivisor);
1864 cd_setreg(com, CD1400_TCOR, oprescaler);
1870 * transmitter enable (always set)
1873 opt = CD1400_CCR_CMDCHANCTL | CD1400_CCR_XMTEN
1874 | (cflag & CREAD ? CD1400_CCR_RCVEN : CD1400_CCR_RCVDIS);
1875 if (opt != com->channel_control) {
1876 com->channel_control = opt;
1877 cd1400_channel_cmd(com, opt);
1881 /* set special chars */
1882 /* XXX if one is _POSIX_VDISABLE, can't use some others */
1883 if (t->c_cc[VSTOP] != _POSIX_VDISABLE)
1884 cd_setreg(com, CD1400_SCHR1, t->c_cc[VSTOP]);
1885 if (t->c_cc[VSTART] != _POSIX_VDISABLE)
1886 cd_setreg(com, CD1400_SCHR2, t->c_cc[VSTART]);
1887 if (t->c_cc[VINTR] != _POSIX_VDISABLE)
1888 cd_setreg(com, CD1400_SCHR3, t->c_cc[VINTR]);
1889 if (t->c_cc[VSUSP] != _POSIX_VDISABLE)
1890 cd_setreg(com, CD1400_SCHR4, t->c_cc[VSUSP]);
1894 * set channel option register 1 -
1901 if (cflag & PARENB) {
1903 opt |= CD1400_COR1_PARODD;
1904 opt |= CD1400_COR1_PARNORMAL;
1907 if (!(iflag & INPCK))
1908 opt |= CD1400_COR1_NOINPCK;
1911 if (cflag & CSTOPB) {
1913 opt |= CD1400_COR1_STOP2;
1916 switch (cflag & CSIZE) {
1919 opt |= CD1400_COR1_CS5;
1923 opt |= CD1400_COR1_CS6;
1927 opt |= CD1400_COR1_CS7;
1931 opt |= CD1400_COR1_CS8;
1935 if (opt != com->cor[0]) {
1936 cor_change |= CD1400_CCR_COR1;
1937 cd_setreg(com, CD1400_COR1, com->cor[0] = opt);
1941 * Set receive time-out period, normally to max(one char time, 5 ms).
1943 if (t->c_ispeed == 0)
1944 itimeout = cd_getreg(com, CD1400_RTPR);
1946 itimeout = (1000 * bits + t->c_ispeed - 1) / t->c_ispeed;
1952 if (itimeout < MIN_RTP)
1955 if (!(t->c_lflag & ICANON) && t->c_cc[VMIN] != 0 && t->c_cc[VTIME] != 0
1956 && t->c_cc[VTIME] * 10 > itimeout)
1957 itimeout = t->c_cc[VTIME] * 10;
1960 cd_setreg(com, CD1400_RTPR, itimeout);
1963 * set channel option register 2 -
1969 opt |= CD1400_COR2_IXANY;
1971 opt |= CD1400_COR2_IXOFF;
1973 #ifndef SOFT_CTS_OFLOW
1974 if (cflag & CCTS_OFLOW)
1975 opt |= CD1400_COR2_CCTS_OFLOW;
1978 if (opt != com->cor[1]) {
1979 cor_change |= CD1400_CCR_COR2;
1980 cd_setreg(com, CD1400_COR2, com->cor[1] = opt);
1985 * set channel option register 3 -
1986 * receiver FIFO interrupt threshold
1989 opt = RxFifoThreshold;
1991 if (t->c_lflag & ICANON)
1992 opt |= CD1400_COR3_SCD34; /* detect INTR & SUSP chars */
1994 /* detect and transparently handle START and STOP chars */
1995 opt |= CD1400_COR3_FCT | CD1400_COR3_SCD12;
1997 if (opt != com->cor[2]) {
1998 cor_change |= CD1400_CCR_COR3;
1999 cd_setreg(com, CD1400_COR3, com->cor[2] = opt);
2002 /* notify the CD1400 if COR1-3 have changed */
2004 cd1400_channel_cmd(com, CD1400_CCR_CMDCORCHG | cor_change);
2007 * set channel option register 4 -
2010 * received exception processing
2014 opt |= CD1400_COR4_IGNCR;
2017 * we need a new ttyinput() for this, as we don't want to
2018 * have ICRNL && INLCR being done in both layers, or to have
2019 * synchronisation problems
2022 opt |= CD1400_COR4_ICRNL;
2024 opt |= CD1400_COR4_INLCR;
2027 opt |= CD1400_COR4_IGNBRK | CD1400_COR4_NOBRKINT;
2029 * The `-ignbrk -brkint parmrk' case is not handled by the hardware,
2030 * so only tell the hardware about -brkint if -parmrk.
2032 if (!(iflag & (BRKINT | PARMRK)))
2033 opt |= CD1400_COR4_NOBRKINT;
2035 /* XXX using this "intelligence" breaks reporting of overruns. */
2037 opt |= CD1400_COR4_PFO_DISCARD;
2040 opt |= CD1400_COR4_PFO_ESC;
2042 opt |= CD1400_COR4_PFO_NUL;
2045 opt |= CD1400_COR4_PFO_EXCEPTION;
2047 cd_setreg(com, CD1400_COR4, opt);
2050 * set channel option register 5 -
2054 opt |= CD1400_COR5_ISTRIP;
2055 if (t->c_iflag & IEXTEN)
2056 /* enable LNEXT (e.g. ctrl-v quoting) handling */
2057 opt |= CD1400_COR5_LNEXT;
2059 if (t->c_oflag & ONLCR)
2060 opt |= CD1400_COR5_ONLCR;
2061 if (t->c_oflag & OCRNL)
2062 opt |= CD1400_COR5_OCRNL;
2064 cd_setreg(com, CD1400_COR5, opt);
2067 * We always generate modem status change interrupts for CD changes.
2068 * Among other things, this is necessary to track TS_CARR_ON for
2069 * pstat to print even when the driver doesn't care. CD changes
2070 * should be rare so interrupts for them are not worth extra code to
2071 * avoid. We avoid interrupts for other modem status changes (except
2072 * for CTS changes when SOFT_CTS_OFLOW is configured) since this is
2073 * simplest and best.
2077 * set modem change option register 1
2078 * generate modem interrupts on which 1 -> 0 input transitions
2079 * also controls auto-DTR output flow-control, which we don't use
2081 opt = CD1400_MCOR1_CDzd;
2082 #ifdef SOFT_CTS_OFLOW
2083 if (cflag & CCTS_OFLOW)
2084 opt |= CD1400_MCOR1_CTSzd;
2086 cd_setreg(com, CD1400_MCOR1, opt);
2089 * set modem change option register 2
2090 * generate modem interrupts on specific 0 -> 1 input transitions
2092 opt = CD1400_MCOR2_CDod;
2093 #ifdef SOFT_CTS_OFLOW
2094 if (cflag & CCTS_OFLOW)
2095 opt |= CD1400_MCOR2_CTSod;
2097 cd_setreg(com, CD1400_MCOR2, opt);
2100 * XXX should have done this long ago, but there is too much state
2101 * to change all atomically.
2105 com->state &= ~CS_TTGO;
2106 if (!(tp->t_state & TS_TTSTOP))
2107 com->state |= CS_TTGO;
2108 if (cflag & CRTS_IFLOW) {
2109 com->state |= CS_RTS_IFLOW;
2111 * If CS_RTS_IFLOW just changed from off to on, the change
2112 * needs to be propagated to MCR_RTS. This isn't urgent,
2113 * so do it later by calling comstart() instead of repeating
2114 * a lot of code from comstart() here.
2116 } else if (com->state & CS_RTS_IFLOW) {
2117 com->state &= ~CS_RTS_IFLOW;
2119 * CS_RTS_IFLOW just changed from on to off. Force MCR_RTS
2120 * on here, since comstart() won't do it later.
2123 outb(com->modem_ctl_port, com->mcr_image |= MCR_RTS);
2125 cd_setreg(com, com->mcr_rts_reg,
2126 com->mcr_image |= com->mcr_rts);
2131 * Set up state to handle output flow control.
2132 * XXX - worth handling MDMBUF (DCD) flow control at the lowest level?
2133 * Now has 10+ msec latency, while CTS flow has 50- usec latency.
2135 com->state |= CS_ODEVREADY;
2136 #ifdef SOFT_CTS_OFLOW
2137 com->state &= ~CS_CTS_OFLOW;
2138 if (cflag & CCTS_OFLOW) {
2139 com->state |= CS_CTS_OFLOW;
2140 if (!(com->last_modem_status & MSR_CTS))
2141 com->state &= ~CS_ODEVREADY;
2144 /* XXX shouldn't call functions while intrs are disabled. */
2145 disc_optim(tp, t, com);
2148 * Recover from fiddling with CS_TTGO. We used to call siointr1()
2149 * unconditionally, but that defeated the careful discarding of
2150 * stale input in sioopen().
2152 if (com->state >= (CS_BUSY | CS_TTGO))
2155 if (com->state >= (CS_BUSY | CS_TTGO | CS_ODEVREADY)) {
2156 if (!(com->intr_enable & CD1400_SRER_TXRDY))
2157 cd_setreg(com, CD1400_SRER,
2159 = (com->intr_enable & ~CD1400_SRER_TXMPTY)
2160 | CD1400_SRER_TXRDY);
2162 if (com->intr_enable & CD1400_SRER_TXRDY)
2163 cd_setreg(com, CD1400_SRER,
2165 = (com->intr_enable & ~CD1400_SRER_TXRDY)
2166 | CD1400_SRER_TXMPTY);
2172 if (com->ibufold != NULL) {
2173 free(com->ibufold, M_DEVBUF);
2174 com->ibufold = NULL;
2180 siosetwater(com, speed)
2190 * Make the buffer size large enough to handle a softtty interrupt
2191 * latency of about 2 ticks without loss of throughput or data
2192 * (about 3 ticks if input flow control is not used or not honoured,
2193 * but a bit less for CS5-CS7 modes).
2195 cp4ticks = speed / 10 / hz * 4;
2196 for (ibufsize = 128; ibufsize < cp4ticks;)
2198 if (ibufsize == com->ibufsize) {
2204 * Allocate input buffer. The extra factor of 2 in the size is
2205 * to allow for an error byte for each input byte.
2207 ibuf = malloc(2 * ibufsize, M_DEVBUF, M_NOWAIT);
2213 /* Initialize non-critical variables. */
2214 com->ibufold = com->ibuf;
2215 com->ibufsize = ibufsize;
2218 tp->t_ififosize = 2 * ibufsize;
2219 tp->t_ispeedwat = (speed_t)-1;
2220 tp->t_ospeedwat = (speed_t)-1;
2224 * Read current input buffer, if any. Continue with interrupts
2228 if (com->iptr != com->ibuf)
2232 * Initialize critical variables, including input buffer watermarks.
2233 * The external device is asked to stop sending when the buffer
2234 * exactly reaches high water, or when the high level requests it.
2235 * The high level is notified immediately (rather than at a later
2236 * clock tick) when this watermark is reached.
2237 * The buffer size is chosen so the watermark should almost never
2239 * The low watermark is invisibly 0 since the buffer is always
2240 * emptied all at once.
2242 com->iptr = com->ibuf = ibuf;
2243 com->ibufend = ibuf + ibufsize;
2244 com->ierroff = ibufsize;
2245 com->ihighwater = ibuf + 3 * ibufsize / 4;
2260 unit = DEV_TO_UNIT(tp->t_dev);
2261 com = com_addr(unit);
2270 if (tp->t_state & TS_TTSTOP) {
2271 com->state &= ~CS_TTGO;
2272 if (com->intr_enable & CD1400_SRER_TXRDY)
2273 cd_setreg(com, CD1400_SRER,
2275 = (com->intr_enable & ~CD1400_SRER_TXRDY)
2276 | CD1400_SRER_TXMPTY);
2278 com->state |= CS_TTGO;
2279 if (com->state >= (CS_BUSY | CS_TTGO | CS_ODEVREADY)
2280 && !(com->intr_enable & CD1400_SRER_TXRDY))
2281 cd_setreg(com, CD1400_SRER,
2283 = (com->intr_enable & ~CD1400_SRER_TXMPTY)
2284 | CD1400_SRER_TXRDY);
2286 if (tp->t_state & TS_TBLOCK) {
2287 if (com->mcr_image & com->mcr_rts && com->state & CS_RTS_IFLOW)
2289 outb(com->modem_ctl_port, com->mcr_image &= ~MCR_RTS);
2291 cd_setreg(com, com->mcr_rts_reg,
2292 com->mcr_image &= ~com->mcr_rts);
2295 if (!(com->mcr_image & com->mcr_rts)
2296 && com->iptr < com->ihighwater
2297 && com->state & CS_RTS_IFLOW)
2299 outb(com->modem_ctl_port, com->mcr_image |= MCR_RTS);
2301 cd_setreg(com, com->mcr_rts_reg,
2302 com->mcr_image |= com->mcr_rts);
2306 if (tp->t_state & (TS_TIMEOUT | TS_TTSTOP)) {
2311 if (tp->t_outq.c_cc != 0) {
2315 if (!com->obufs[0].l_queued) {
2319 com->obufs[0].l_tail
2320 = com->obuf1 + q_to_b(&tp->t_outq, com->obuf1,
2322 com->obufs[0].l_next = NULL;
2323 com->obufs[0].l_queued = TRUE;
2325 if (com->state & CS_BUSY) {
2326 qp = com->obufq.l_next;
2327 while ((next = qp->l_next) != NULL)
2329 qp->l_next = &com->obufs[0];
2331 com->obufq.l_head = com->obufs[0].l_head;
2332 com->obufq.l_tail = com->obufs[0].l_tail;
2333 com->obufq.l_next = &com->obufs[0];
2334 com->state |= CS_BUSY;
2335 if (com->state >= (CS_BUSY | CS_TTGO
2337 cd_setreg(com, CD1400_SRER,
2340 & ~CD1400_SRER_TXMPTY)
2341 | CD1400_SRER_TXRDY);
2345 if (tp->t_outq.c_cc != 0 && !com->obufs[1].l_queued) {
2349 com->obufs[1].l_tail
2350 = com->obuf2 + q_to_b(&tp->t_outq, com->obuf2,
2352 com->obufs[1].l_next = NULL;
2353 com->obufs[1].l_queued = TRUE;
2355 if (com->state & CS_BUSY) {
2356 qp = com->obufq.l_next;
2357 while ((next = qp->l_next) != NULL)
2359 qp->l_next = &com->obufs[1];
2361 com->obufq.l_head = com->obufs[1].l_head;
2362 com->obufq.l_tail = com->obufs[1].l_tail;
2363 com->obufq.l_next = &com->obufs[1];
2364 com->state |= CS_BUSY;
2365 if (com->state >= (CS_BUSY | CS_TTGO
2367 cd_setreg(com, CD1400_SRER,
2370 & ~CD1400_SRER_TXMPTY)
2371 | CD1400_SRER_TXRDY);
2375 tp->t_state |= TS_BUSY;
2383 if (com->state >= (CS_BUSY | CS_TTGO))
2384 siointr1(com); /* fake interrupt to start output */
2399 com = com_addr(DEV_TO_UNIT(tp->t_dev));
2403 com->obufs[0].l_queued = FALSE;
2404 com->obufs[1].l_queued = FALSE;
2405 if (com->extra_state & CSE_ODONE) {
2406 com_events -= LOTS_OF_EVENTS;
2407 com->extra_state &= ~CSE_ODONE;
2408 if (com->etc != ETC_NONE) {
2409 if (com->etc == ETC_BREAK_ENDED)
2410 com->etc = ETC_NONE;
2414 com->tp->t_state &= ~TS_BUSY;
2415 if (com->state & CS_ODONE)
2416 com_events -= LOTS_OF_EVENTS;
2417 com->state &= ~(CS_ODONE | CS_BUSY);
2420 /* XXX no way to reset only input fifo. */
2421 com_events -= (com->iptr - com->ibuf);
2422 com->iptr = com->ibuf;
2427 if (rw & FWRITE && com->etc == ETC_NONE)
2428 cd1400_channel_cmd(com, CD1400_CCR_CMDRESET | CD1400_CCR_FTF);
2433 commctl(com, bits, how)
2442 if (com->channel_control & CD1400_CCR_RCVEN)
2444 mcr = com->mcr_image;
2445 if (mcr & com->mcr_dtr)
2447 if (mcr & com->mcr_rts)
2448 /* XXX wired on for Cyclom-8Ys */
2452 * We must read the modem status from the hardware because
2453 * we don't generate modem status change interrupts for all
2454 * changes, so com->prev_modem_status is not guaranteed to
2455 * be up to date. This is safe, unlike for sio, because
2456 * reading the status register doesn't clear pending modem
2457 * status change interrupts.
2459 msr = cd_getreg(com, CD1400_MSVR2);
2468 /* XXX not connected except for Cyclom-16Y? */
2473 if (bits & TIOCM_DTR)
2474 mcr |= com->mcr_dtr;
2475 if (bits & TIOCM_RTS)
2476 mcr |= com->mcr_rts;
2480 com->mcr_image = mcr;
2481 cd_setreg(com, CD1400_MSVR1, mcr);
2482 cd_setreg(com, CD1400_MSVR2, mcr);
2485 com->mcr_image = mcr = com->mcr_image | mcr;
2486 cd_setreg(com, CD1400_MSVR1, mcr);
2487 cd_setreg(com, CD1400_MSVR2, mcr);
2490 com->mcr_image = mcr = com->mcr_image & ~mcr;
2491 cd_setreg(com, CD1400_MSVR1, mcr);
2492 cd_setreg(com, CD1400_MSVR2, mcr);
2507 * Set our timeout period to 1 second if no polled devices are open.
2508 * Otherwise set it to max(1/200, 1/hz).
2509 * Enable timeouts iff some device is open.
2511 untimeout(comwakeup, (void *)NULL, sio_timeout_handle);
2514 for (unit = 0; unit < NSIO; ++unit) {
2515 com = com_addr(unit);
2516 if (com != NULL && com->tp != NULL
2517 && com->tp->t_state & TS_ISOPEN) {
2520 if (com->poll || com->poll_output) {
2521 sio_timeout = hz > 200 ? hz / 200 : 1;
2528 sio_timeouts_until_log = hz / sio_timeout;
2529 sio_timeout_handle = timeout(comwakeup, (void *)NULL,
2532 /* Flush error messages, if any. */
2533 sio_timeouts_until_log = 1;
2534 comwakeup((void *)NULL);
2535 untimeout(comwakeup, (void *)NULL, sio_timeout_handle);
2546 sio_timeout_handle = timeout(comwakeup, (void *)NULL, sio_timeout);
2550 * Recover from lost output interrupts.
2551 * Poll any lines that don't use interrupts.
2553 for (unit = 0; unit < NSIO; ++unit) {
2554 com = com_addr(unit);
2556 && (com->state >= (CS_BUSY | CS_TTGO) || com->poll)) {
2565 * Check for and log errors, but not too often.
2567 if (--sio_timeouts_until_log > 0)
2569 sio_timeouts_until_log = hz / sio_timeout;
2570 for (unit = 0; unit < NSIO; ++unit) {
2573 com = com_addr(unit);
2576 for (errnum = 0; errnum < CE_NTYPES; ++errnum) {
2581 delta = com->delta_error_counts[errnum];
2582 com->delta_error_counts[errnum] = 0;
2586 total = com->error_counts[errnum] += delta;
2587 log(LOG_ERR, "cy%d: %u more %s%s (total %lu)\n",
2588 unit, delta, error_desc[errnum],
2589 delta == 1 ? "" : "s", total);
2595 disc_optim(tp, t, com)
2600 #ifndef SOFT_HOTCHAR
2605 * XXX can skip a lot more cases if Smarts. Maybe
2606 * (IGNCR | ISTRIP | IXON) in c_iflag. But perhaps we
2607 * shouldn't skip if (TS_CNTTB | TS_LNCH) is set in t_state.
2609 if (!(t->c_iflag & (ICRNL | IGNCR | IMAXBEL | INLCR | ISTRIP | IXON))
2610 && (!(t->c_iflag & BRKINT) || (t->c_iflag & IGNBRK))
2611 && (!(t->c_iflag & PARMRK)
2612 || (t->c_iflag & (IGNPAR | IGNBRK)) == (IGNPAR | IGNBRK))
2613 && !(t->c_lflag & (ECHO | ICANON | IEXTEN | ISIG | PENDIN))
2614 && linesw[tp->t_line].l_rint == ttyinput)
2615 tp->t_state |= TS_CAN_BYPASS_L_RINT;
2617 tp->t_state &= ~TS_CAN_BYPASS_L_RINT;
2618 com->hotchar = linesw[tp->t_line].l_hotchar;
2619 #ifndef SOFT_HOTCHAR
2620 opt = com->cor[2] & ~CD1400_COR3_SCD34;
2621 if (com->hotchar != 0) {
2622 cd_setreg(com, CD1400_SCHR3, com->hotchar);
2623 cd_setreg(com, CD1400_SCHR4, com->hotchar);
2624 opt |= CD1400_COR3_SCD34;
2626 if (opt != com->cor[2]) {
2627 cd_setreg(com, CD1400_COR3, com->cor[2] = opt);
2628 cd1400_channel_cmd(com, CD1400_CCR_CMDCORCHG | CD1400_CCR_COR3);
2634 /* standard line discipline input routine */
2640 /* XXX duplicate ttyinput(), but without the IXOFF/IXON/ISTRIP/IPARMRK
2641 * bits, as they are done by the CD1400. Hardly worth the effort,
2642 * given that high-throughput sessions are raw anyhow.
2648 comspeed(speed, cy_clock, prescaler_io)
2661 if (speed < 0 || speed > 150000)
2664 /* determine which prescaler to use */
2665 for (prescaler_unit = 4, prescaler = 2048; prescaler_unit;
2666 prescaler_unit--, prescaler >>= 2) {
2667 if (cy_clock / prescaler / speed > 63)
2671 divider = (cy_clock / prescaler * 2 / speed + 1) / 2; /* round off */
2674 actual = cy_clock/prescaler/divider;
2676 /* 10 times error in percent: */
2677 error = ((actual - (long)speed) * 2000 / (long)speed + 1) / 2;
2679 /* 3.0% max error tolerance */
2680 if (error < -30 || error > 30)
2684 printf("prescaler = %d (%d)\n", prescaler, prescaler_unit);
2685 printf("divider = %d (%x)\n", divider, divider);
2686 printf("actual = %d\n", actual);
2687 printf("error = %d\n", error);
2690 *prescaler_io = prescaler_unit;
2695 cd1400_channel_cmd(com, cmd)
2699 cd1400_channel_cmd_wait(com);
2700 cd_setreg(com, CD1400_CCR, cmd);
2701 cd1400_channel_cmd_wait(com);
2705 cd1400_channel_cmd_wait(com)
2708 struct timeval start;
2712 if (cd_getreg(com, CD1400_CCR) == 0)
2716 if (cd_getreg(com, CD1400_CCR) == 0)
2719 usec = 1000000 * (tv.tv_sec - start.tv_sec) +
2720 tv.tv_usec - start.tv_usec;
2723 "cy%d: channel command timeout (%ld usec)\n",
2736 * We can't change the hardware's ETC state while there are any
2737 * characters in the tx fifo, since those characters would be
2738 * interpreted as commands! Unputting characters from the fifo
2739 * is difficult, so we wait up to 12 character times for the fifo
2740 * to drain. The command will be delayed for up to 2 character
2741 * times for the tx to become empty. Unputting characters from
2742 * the tx holding and shift registers is impossible, so we wait
2743 * for the tx to become empty so that the command is sure to be
2744 * executed soon after we issue it.
2747 if (com->etc == etc) {
2751 if ((etc == CD1400_ETC_SENDBREAK
2752 && (com->etc == ETC_BREAK_STARTING
2753 || com->etc == ETC_BREAK_STARTED))
2754 || (etc == CD1400_ETC_STOPBREAK
2755 && (com->etc == ETC_BREAK_ENDING || com->etc == ETC_BREAK_ENDED
2756 || com->etc == ETC_NONE))) {
2761 cd_setreg(com, CD1400_SRER,
2763 = (com->intr_enable & ~CD1400_SRER_TXRDY) | CD1400_SRER_TXMPTY);
2766 while (com->etc == etc
2767 && tsleep(&com->etc, PCATCH, "cyetc", 0) == 0)
2776 struct com_s *basecom;
2783 basecom = com_addr(com->unit & ~(CD1400_NO_OF_CHANNELS - 1));
2784 car = com->unit & CD1400_CAR_CHAN;
2785 cy_align = com->cy_align;
2786 iobase = com->iobase;
2790 if (basecom->car != car)
2791 cd_outb(iobase, CD1400_CAR, cy_align, basecom->car = car);
2792 val = cd_inb(iobase, reg, cy_align);
2799 cd_setreg(com, reg, val)
2804 struct com_s *basecom;
2810 basecom = com_addr(com->unit & ~(CD1400_NO_OF_CHANNELS - 1));
2811 car = com->unit & CD1400_CAR_CHAN;
2812 cy_align = com->cy_align;
2813 iobase = com->iobase;
2817 if (basecom->car != car)
2818 cd_outb(iobase, CD1400_CAR, cy_align, basecom->car = car);
2819 cd_outb(iobase, reg, cy_align, val);
2835 com = com_addr(unit);
2836 printf("info for channel %d\n", unit);
2837 printf("------------------\n");
2838 printf("total cyclom service probes:\t%d\n", cy_svrr_probes);
2839 printf("calls to upper layer:\t\t%d\n", cy_timeouts);
2842 iobase = com->iobase;
2844 printf("cd1400 base address:\\tt%p\n", iobase);
2845 printf("saved channel_control:\t\t0x%02x\n", com->channel_control);
2846 printf("saved cor1-3:\t\t\t0x%02x 0x%02x 0x%02x\n",
2847 com->cor[0], com->cor[1], com->cor[2]);
2848 printf("service request enable reg:\t0x%02x (0x%02x cached)\n",
2849 cd_getreg(com, CD1400_SRER), com->intr_enable);
2850 printf("service request register:\t0x%02x\n",
2851 cd_inb(iobase, CD1400_SVRR, com->cy_align));
2852 printf("modem status:\t\t\t0x%02x (0x%02x cached)\n",
2853 cd_getreg(com, CD1400_MSVR2), com->prev_modem_status);
2854 printf("rx/tx/mdm interrupt registers:\t0x%02x 0x%02x 0x%02x\n",
2855 cd_inb(iobase, CD1400_RIR, com->cy_align),
2856 cd_inb(iobase, CD1400_TIR, com->cy_align),
2857 cd_inb(iobase, CD1400_MIR, com->cy_align));
2859 printf("com state:\t\t\t0x%02x\n", com->state);
2860 printf("calls to comstart():\t\t%d (%d useful)\n",
2861 com->start_count, com->start_real);
2862 printf("rx buffer chars free:\t\t%d\n", com->iptr - com->ibuf);
2864 if (com->obufs[0].l_queued)
2865 ocount += com->obufs[0].l_tail - com->obufs[0].l_head;
2866 if (com->obufs[1].l_queued)
2867 ocount += com->obufs[1].l_tail - com->obufs[1].l_head;
2868 printf("tx buffer chars:\t\t%u\n", ocount);
2869 printf("received chars:\t\t\t%d\n", com->bytes_in);
2870 printf("received exceptions:\t\t%d\n", com->recv_exception);
2871 printf("modem signal deltas:\t\t%d\n", com->mdm);
2872 printf("transmitted chars:\t\t%d\n", com->bytes_out);
2876 printf("tty state:\t\t\t0x%08x\n", tp->t_state);
2878 "upper layer queue lengths:\t%d raw, %d canon, %d output\n",
2879 tp->t_rawq.c_cc, tp->t_canq.c_cc, tp->t_outq.c_cc);
2881 printf("tty state:\t\t\tclosed\n");
2883 #endif /* CyDebug */