1 .\" Copyright (c) 1983, 1991, 1993
2 .\" The Regents of the University of California. All rights reserved.
4 .\" Redistribution and use in source and binary forms, with or without
5 .\" modification, are permitted provided that the following conditions
7 .\" 1. Redistributions of source code must retain the above copyright
8 .\" notice, this list of conditions and the following disclaimer.
9 .\" 2. Redistributions in binary form must reproduce the above copyright
10 .\" notice, this list of conditions and the following disclaimer in the
11 .\" documentation and/or other materials provided with the distribution.
12 .\" 4. Neither the name of the University nor the names of its contributors
13 .\" may be used to endorse or promote products derived from this software
14 .\" without specific prior written permission.
16 .\" THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS ``AS IS'' AND
17 .\" ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
18 .\" IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
19 .\" ARE DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE
20 .\" FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
21 .\" DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
22 .\" OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
23 .\" HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
24 .\" LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
25 .\" OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
28 .\" From: @(#)ifconfig.8 8.3 (Berkeley) 1/5/94
29 .\" $FreeBSD: src/sbin/ifconfig/ifconfig.8,v 1.124 2006/10/10 09:44:08 ru Exp $
36 .Nd configure network interface parameters
77 utility is used to assign an address
78 to a network interface and/or configure
79 network interface parameters.
82 utility must be used at boot time to define the network address
83 of each interface present on a machine; it may also be used at
84 a later time to redefine an interface's address
85 or other operating parameters.
87 The following options are available:
88 .Bl -tag -width indent
91 .Tn DARPA Ns -Internet
93 the address is either a host name present in the host name data
98 Internet address expressed in the Internet standard
101 It is also possible to use the CIDR notation (also known as the
102 slash notation) to include the netmask.
103 That is, one can specify an address like
108 family, it is also possible to specify the prefix length using the slash
113 parameter below for more information.
114 .\" For the Xerox Network Systems(tm) family,
116 .\" .Ar net:a.b.c.d.e.f ,
119 .\" is the assigned network number (in decimal),
120 .\" and each of the six bytes of the host number,
124 .\" are specified in hexadecimal.
125 .\" The host number may be omitted on IEEE 802 protocol
126 .\" (Ethernet, FDDI, and Token Ring) interfaces,
127 .\" which use the hardware physical address,
128 .\" and on interfaces other than the first.
131 .\" family, addresses are specified as a long hexadecimal string,
132 .\" as in the Xerox family.
133 .\" However, two consecutive dots imply a zero
134 .\" byte, and the dots are optional, if the user wishes to (carefully)
135 .\" count out long strings of digits in network byte order.
140 is specified as a series of colon-separated hex digits.
142 e.g.\& set a new MAC address on an ethernet interface, though the
143 mechanism used is not ethernet-specific.
144 If the interface is already
145 up when this option is used, it will be briefly brought down and
146 then brought back up again in order to ensure that the receive
147 filter in the underlying ethernet hardware is properly reprogrammed.
148 .It Ar address_family
151 which affects interpretation of the remaining parameters.
152 Since an interface can receive transmissions in differing protocols
153 with different naming schemes, specifying the address family is recommended.
154 The address or protocol families currently
173 Specify the address of the correspondent on the other end
174 of a point to point link.
177 parameter is a string of the form
183 The following parameters may be set with
185 .Bl -tag -width indent
190 Introduced for compatibility
194 Establish an additional network address for this interface.
195 This is sometimes useful when changing network numbers, and
196 one wishes to accept packets addressed to the old interface.
197 If the address is on the same subnet as the first network address
198 for this interface, a non-conflicting netmask must be given.
203 Remove the network address specified.
204 This would be used if you incorrectly specified an alias, or it
205 was no longer needed.
206 If you have incorrectly set an NS address having the side effect
207 of specifying the host portion, removing all NS addresses will
208 allow you to respecify the host portion.
211 Specify that the address configured is an anycast address.
212 Based on the current specification,
213 only routers may configure anycast addresses.
214 Anycast address will not be used as source address of any of outgoing
217 Enable the use of the Address Resolution Protocol
220 between network level addresses and link level addresses (default).
221 This is currently implemented for mapping between
226 802 48-bit MAC addresses (Ethernet, FDDI, and Token Ring addresses).
228 Disable the use of the Address Resolution Protocol
231 If the Address Resolution Protocol is enabled,
232 the host will only reply to requests for its addresses,
233 and will never send any requests.
235 If the Address Resolution Protocol is enabled,
236 the host will perform normally,
237 sending out requests and listening for replies.
240 Specify the address to use to represent broadcasts to the
242 The default broadcast address is the address with a host part of all 1's.
244 Enable driver dependent debugging code; usually, this turns on
245 extra console error logging.
247 Disable driver dependent debugging code.
249 Put interface into permanently promiscuous mode.
251 Disable permanently promiscuous mode.
259 When an interface is marked
261 the system will not attempt to
262 transmit messages through that interface.
263 If possible, the interface will be reset to disable reception as well.
264 This action does not automatically disable routes using the interface.
268 (lowermost 64bit of an IPv6 address)
271 This is used to specify an Internet host who is willing to receive
272 IP packets encapsulating IPX packets bound for a remote network.
273 An apparent point to point link is constructed, and
274 the address specified will be taken as the IPX address and network
277 If the driver supports the media selection system, set the media type
280 Some interfaces support the mutually exclusive use of one of several
281 different physical media connectors.
282 For example, a 10Mbit/s Ethernet
283 interface might support the use of either
285 or twisted pair connectors.
286 Setting the media type to
288 would change the currently active connector to the AUI port.
291 would activate twisted pair.
292 Refer to the interfaces' driver
293 specific documentation or man page for a complete list of the
295 .It Cm mediaopt Ar opts
296 If the driver supports the media selection system, set the specified
297 media options on the interface.
301 is a comma delimited list of options to apply to the interface.
302 Refer to the interfaces' driver specific man page for a complete
303 list of available options.
304 .It Fl mediaopt Ar opts
305 If the driver supports the media selection system, disable the
306 specified media options on the interface.
308 If the driver supports the media selection system, set the specified
309 operating mode on the interface to
311 For IEEE 802.11 wireless interfaces that support multiple operating modes
312 this directive is used to select between 802.11a
320 Set the interface name to
323 If the driver supports receive side scaling,
324 enable receive side scaling on the interface.
326 If the driver supports receive side scaling,
327 disable receive side scaling on the interface.
328 .It Cm rxcsum , txcsum
329 If the driver supports user-configurable checksum offloading,
330 enable receive (or transmit) checksum offloading on the interface.
331 Some drivers may not be able to enable these flags independently
332 of each other, so setting one may also set the other.
333 The driver will offload as much checksum work as it can reliably
334 support, the exact level of offloading varies between drivers.
335 .It Fl rxcsum , txcsum
336 If the driver supports user-configurable checksum offloading,
337 disable receive (or transmit) checksum offloading on the interface.
338 These settings may not always be independent of each other.
339 .It Cm vlanmtu , vlanhwtag
340 If the driver offers user-configurable VLAN support, enable
341 reception of extended frames or tag processing in hardware,
343 Note that this must be issued on a physical interface associated with
348 .It Fl vlanmtu , vlanhwtag
349 If the driver offers user-configurable VLAN support, disable
350 reception of extended frames or tag processing in hardware,
352 .It Cm pollcpu Ar cpu
355 feature and disable interrupts on the interface,
356 if the driver supports this mode and
360 Driver will be polled by
365 feature and disable interrupts on the interface, if the driver supports
370 feature and enable interrupt mode on the interface.
372 Create the specified network pseudo-device.
373 If the interface is given without a unit number, try to create a new
374 device with an arbitrary unit number.
375 If creation of an arbitrary device is successful, the new device name is
376 printed to standard output unless the interface is renamed or destroyed
381 Destroy the specified network pseudo-device.
397 Set the routing metric of the interface to
400 The routing metric is used by the routing protocol
402 Higher metrics have the effect of making a route
403 less favorable; metrics are counted as additional hops
404 to the destination network or host.
406 Set the maximum transmission unit of the interface to
408 default is interface specific.
409 The MTU is used to limit the size of packets that are transmitted on an
411 Not all interfaces support setting the MTU, and some interfaces have
413 .It Cm netmask Ar mask
416 Specify how much of the address to reserve for subdividing
417 networks into sub-networks.
418 The mask includes the network part of the local address
419 and the subnet part, which is taken from the host field of the address.
420 The mask can be specified as a single hexadecimal number
423 with a dot-notation Internet address,
424 or with a pseudo-network name listed in the network table
426 The mask contains 1's for the bit positions in the 32-bit address
427 which are to be used for the network and subnet parts,
428 and 0's for the host part.
429 The mask should contain at least the standard network portion,
430 and the subnet field should be contiguous with the network
433 The netmask can also be specified in CIDR notation after the address.
436 option above for more information.
439 Enable autoconfiguration.
441 Disable autoconfiguration.
444 Set preferred lifetime for the address.
447 Set valid lifetime for the address.
448 .It Cm prefixlen Ar len
452 bits are reserved for subdividing networks into sub-networks.
455 must be integer, and for syntactical reason it must be between 0 to 128.
456 It is almost always 64 under the current IPv6 assignment rule.
457 If the parameter is omitted, 64 is used.
459 The prefix can also be specified using the slash notation after the address.
462 option above for more information.
465 Set the IPv6 deprecated address bit.
468 Clear the IPv6 deprecated address bit.
471 Set the IPv6 tentative address bit.
474 Clear the IPv6 tentative address bit.
477 .\" .It Cm nsellength Ar n
480 .\" This specifies a trailing number of bytes for a received
482 .\" used for local identification, the remaining leading part of which is
485 .\" (Network Entity Title).
486 .\" The default value is 1, which is conformant to US
488 .\" When an ISO address is set in an ifconfig command,
491 .\" which is being specified.
494 .\" 20 hex digits should be
497 .\" to be assigned to the interface.
498 .\" There is some evidence that a number different from 1 may be useful
501 .\" 37 type addresses.
502 .It Cm range Ar netrange
503 Under appletalk, set the interface to respond to a
506 .Ar startnet Ns - Ns Ar endnet .
507 Appletalk uses this scheme instead of
510 implements it internally as a set of netmasks.
515 Introduced for compatibility
519 The argument following this specifies the version (phase) of the
520 Appletalk network attached to the interface.
521 Values of 1 or 2 are permitted.
523 .It Cm link Op Cm 0 No - Cm 2
525 Enable special processing of the link level of the interface.
526 These three options are interface specific in actual effect, however,
527 they are in general used to select special modes of operation.
529 of this is to enable SLIP compression, or to select the connector type
530 for some Ethernet cards.
531 Refer to the man page for the specific driver
532 for more information.
534 .It Fl link Op Cm 0 No - Cm 2
536 Disable special processing at the link level with the specified interface.
550 Put the interface in monitor mode.
551 No packets are transmitted, and received packets are discarded after
555 Take the interface out of monitor mode.
559 This may be used to enable an interface after an
561 It happens automatically when setting the first address on an interface.
562 If the interface was reset when previously marked down,
563 the hardware will be re-initialized.
566 The following parameters are specific to cloning
567 IEEE 802.11 wireless interfaces with the
570 .Bl -tag -width indent
571 .It Cm wlandev Ar device
574 as the parent for the cloned device.
575 .It Cm wlanmode Ar mode
576 Specify the operating mode for this cloned device.
594 The operating mode of a cloned interface cannot be changed.
597 mode is actually implemented as an
599 interface with special properties.
600 .It Cm wlanbssid Ar bssid
601 The 802.11 mac address to use for the bssid.
602 This must be specified at create time for a legacy
605 .It Cm wlanaddr Ar address
606 The local mac address.
607 If this is not specified then a mac address will automatically be assigned
608 to the cloned device.
609 Typically this address is the same as the address of the parent device
612 parameter is specified then the driver will craft a unique address for
613 the device (if supported).
617 device as operating in ``legacy mode''.
620 devices have a fixed peer relationship and do not, for example, roam
621 if their peer stops communicating.
622 For completeness a Dynamic WDS (DWDS) interface may marked as
625 Request a unique local mac address for the cloned device.
626 This is only possible if the device supports multiple mac addresses.
627 To force use of the parent's mac address use
630 Mark the cloned interface as depending on hardware support to
631 track received beacons.
632 To have beacons tracked in software use
638 can also be used to indicate no beacons should
639 be transmitted; this can be useful when creating a WDS configuration but
641 interfaces can only be created as companions to an access point.
644 The following parameters are specific to IEEE 802.11 wireless interfaces
648 .Bl -tag -width indent
650 Enable sending and receiving AMPDU frames when using 802.11n (default).
651 The 802.11n specification states a compliant station must be capable
652 of receiving AMPDU frames but transmision is optional.
655 to disable all use of AMPDU with 802.11n.
656 For testing and/or to work around interoperability problems one can use
660 to control use of AMPDU in one direction.
661 .It Cm ampdudensity Ar density
662 Set the AMPDU density parameter used when operating with 802.11n.
663 This parameter controls the inter-packet gap for AMPDU frames.
664 The sending device normally controls this setting but a receiving station
665 may request wider gaps.
668 are 0, .25, .5, 1, 2, 4, 8, and 16 (microseconds).
671 is treated the same as 0.
672 .It Cm ampdulimit Ar limit
673 Set the limit on packet size for receiving AMPDU frames when operating
677 are 8192, 16384, 32768, and 65536 but one can also specify
678 just the unique prefix: 8, 16, 32, 64.
679 Note the sender may limit the size of AMPDU frames to be less
680 than the maximum specified by the receiving station.
682 Enable sending and receiving AMSDU frames when using 802.11n.
683 By default AMSDU is received but not transmitted.
686 to disable all use of AMSDU with 802.11n.
687 For testing and/or to work around interoperability problems one can use
691 to control use of AMSDU in one direction.
692 .It Cm amsdulimit Ar limit
693 Set the limit on packet size for sending and receiving AMSDU frames
694 when operating with 802.11n.
697 are 7935 and 3839 (bytes).
698 Note the sender may limit the size of AMSDU frames to be less
699 than the maximum specified by the receiving station.
700 Note also that devices are not required to support the 7935 limit,
701 only 3839 is required by the specification and the larger value
702 may require more memory to be dedicated to support functionality
705 When operating as an access point, pass packets between
706 wireless clients directly (default).
707 To instead let them pass up through the
708 system and be forwarded using some other mechanism, use
710 Disabling the internal bridging
711 is useful when traffic is to be processed with
713 .It Cm authmode Ar mode
714 Set the desired authentication mode in infrastructure mode.
715 Not all adapters support all modes.
718 .Cm none , open , shared
724 (IEEE WPA/WPA2/802.11i).
729 modes are only useful when using an authentication service
730 (a supplicant for client operation or an authenticator when
731 operating as an access point).
732 Modes are case insensitive.
734 Enable background scanning when operating as a station.
735 Background scanning is a technique whereby a station associated to
736 an access point will temporarily leave the channel to scan for
737 neighboring stations.
738 This allows a station to maintain a cache of nearby access points
739 so that roaming between access points can be done without
740 a lengthy scan operation.
741 Background scanning is done only when a station is not busy and
742 any outbound traffic will cancel a scan operation.
743 Background scanning should never cause packets to be lost though
744 there may be some small latency if outbound traffic interrupts a
746 By default background scanning is enabled if the device is capable.
747 To disable background scanning, use
749 Background scanning is controlled by the
754 Background scanning must be enabled for roaming; this is an artifact
755 of the current implementation and may not be required in the future.
756 .It Cm bgscanidle Ar idletime
757 Set the minimum time a station must be idle (not transmitting or
758 receiving frames) before a background scan is initiated.
761 parameter is specified in milliseconds.
762 By default a station must be idle at least 250 milliseconds before
763 a background scan is initiated.
764 The idle time may not be set to less than 100 milliseconds.
765 .It Cm bgscanintvl Ar interval
766 Set the interval at which background scanning is attempted.
769 parameter is specified in seconds.
770 By default a background scan is considered every 300 seconds (5 minutes).
773 may not be set to less than 15 seconds.
774 .It Cm bintval Ar interval
775 Set the interval at which beacon frames are sent when operating in
779 parameter is specified in TU's (1024 usecs).
780 By default beacon frames are transmitted every 100 TU's.
781 .It Cm bmissthreshold Ar count
782 Set the number of consecutive missed beacons at which the station
783 will attempt to roam (i.e., search for a new access point).
786 parameter must be in the range 1 to 255; though the
787 upper bound may be reduced according to device capabilities.
788 The default threshold is 7 consecutive missed beacons; but
789 this may be overridden by the device driver.
794 .It Cm bssid Ar address
795 Specify the MAC address of the access point to use when operating
796 as a station in a BSS network.
797 This overrides any automatic selection done by the system.
798 To disable a previously selected access point, supply
803 This option is useful when more than one access point uses the same SSID.
809 Enable packet bursting.
810 Packet bursting is a transmission technique whereby the wireless
811 medium is acquired once to send multiple frames and the interframe
813 This technique can significantly increase throughput by reducing
814 transmission overhead.
815 Packet bursting is supported by the 802.11e QoS specification
816 and some devices that do not support QoS may still be capable.
817 By default packet bursting is enabled if a device is capable
819 To disable packet bursting, use
821 .It Cm chanlist Ar channels
822 Set the desired channels to use when scanning for access
823 points, neighbors in an IBSS network, or looking for unoccupied
824 channels when operating as an access point.
825 The set of channels is specified as a comma-separated list with
826 each element in the list representing either a single channel number or a range
829 Channel numbers must be in the range 1 to 255 and be permissible
830 according to the operating characteristics of the device.
831 .It Cm channel Ar number
832 Set a single desired channel.
833 Channels range from 1 to 255, but the exact selection available
834 depends on the region your adaptor was manufactured for.
840 will clear any desired channel and, if the device is marked up,
841 force a scan for a channel to operate on.
842 Alternatively the frequency, in megahertz, may be specified
843 instead of the channel number.
845 When there are several ways to use a channel the channel
846 number/frequency may be appended with attributes to clarify.
847 For example, if a device is capable of operating on channel 6
848 with 802.11n and 802.11g then one can specify that g-only use
849 should be used by specifying ``6:g''.
850 Similarly the channel width can be specified by appending it
851 with ``/''; e.g. ``6/40'' specifies a 40MHz wide channel,
852 These attributes can be combined as in: ``6:ht/40''.
853 The full set of flags specified following a `:'' are:
859 (Atheros Dynamic Turbo mode),
867 (Atheros Static Turbo mode),
870 (Atheros Dynamic Turbo mode, or appended to ``st'' and ``dt'').
871 The full set of channel widths following a '/' are:
873 (5MHz aka quarter-rate channel),
875 (10MHz aka half-rate channel),
877 (20MHz mostly for use in specifying ht20),
880 (40MHz mostly for use in specifying ht40),
882 a 40MHz HT channel specification may include the location
883 of the extension channel by appending ``+'' or ``-'' for above and below,
884 respectively; e.g. ``2437:ht/40+'' specifies 40MHz wide HT operation
885 with the center channel at frequency 2437 and the extension channel above.
886 .It Cm country Ar name
887 Set the country code to use in calculating the regulatory constraints
889 In particular the set of available channels, how the wireless device
890 will operation on the channels, and the maximum transmit power that
891 can be used on a channel are defined by this setting.
892 Country/Region codes are specified as a 2-character abbreviation
893 defined by ISO 3166 or using a longer, but possibly ambiguous, spelling;
894 e.g. "ES" and "Spain".
895 The set of country codes are taken from /etc/regdomain.xml and can also
896 be viewed with the ``list countries'' request.
897 Note that not all devices support changing the country code from a default
898 setting; typically stored in EEPROM.
906 Enable Dynamic Frequency Selection (DFS) as specified in 802.11h.
907 DFS embodies several facilities including detection of overlapping
908 radar signals, dynamic transmit power control, and channel selection
909 according to a least-congested criteria.
910 DFS support is mandatory for some 5Ghz frequencies in certain
912 By default DFS is enabled according to the regulatory definitions
913 specified in /etc/regdomain.xml and the curent country code, regdomain,
915 Note the underlying device (and driver) must support radar detection
916 for full DFS support to work.
917 To be fully compliant with the local regulatory agency frequencies that
918 require DFS should not be used unless it is fully supported.
921 to disable this functionality for testing.
923 Enable support for the 802.11d specification (default).
924 When this support is enabled in station mode, beacon frames that advertise
925 a country code different than the currently configured country code will
926 cause an event to be dispatched to user applications.
927 This event can be used by the station to adopt that country code and
928 operate according to the associated regulatory constraints.
929 When operating as an access point with 802.11d enabled the beacon and
930 probe response frames transmitted will advertise the current regulatory
932 To disable 802.11d use
935 Enable 802.11h support including spectrum management.
936 When 802.11h is enabled beacon and probe response frames will have
937 the SpectrumMgt bit set in the capabilities field and
938 country and power constraint information elements will be present.
939 802.11h support also includes handling Channel Switch Announcements (CSA)
940 which are a mechanism to coordinate channel changes by an access point.
941 By default 802.11h is enabled if the device is capable.
942 To disable 802.11h use
944 .It Cm deftxkey Ar index
945 Set the default key to use for transmission.
946 Typically this is only set when using WEP encryption.
947 Note that you must set a default transmit key
948 for the system to know which key to use in encrypting outbound traffic.
951 is an alias for this request; it is provided for backwards compatibility.
952 .It Cm dtimperiod Ar period
955 period for transmitting buffered multicast data frames when
956 operating in ap mode.
959 specifies the number of beacon intervals between DTIM
960 and must be in the range 1 to 15.
961 By default DTIM is 1 (i.e., DTIM occurs at each beacon).
963 Enable the use of Atheros Dynamic Turbo mode when communicating with
964 another Dynamic Turbo-capable station.
965 Dynamic Turbo mode is an Atheros-specific mechanism by which
966 stations switch between normal 802.11 operation and a ``boosted''
967 mode in which a 40MHz wide channel is used for communication.
968 Stations using Dynamic Turbo mode operate boosted only when the
969 channel is free of non-dturbo stations; when a non-dturbo station
970 is identified on the channel all stations will automatically drop
971 back to normal operation.
972 By default, Dynamic Turbo mode is not enabled, even if the device is capable.
973 Note that turbo mode (dynamic or static) is only allowed on some
974 channels depending on the regulatory constraints; use the
976 command to identify the channels where turbo mode may be used.
977 To disable Dynamic Turbo mode use
980 Enable Dynamic WDS (DWDS) support.
981 DWDS is a facility by which 4-address traffic can be carried between
982 stations operating in infrastructure mode.
983 A station first associates to an access point and authenticates using
984 normal procedures (e.g. WPA).
985 Then 4-address frames are passed to carry traffic for stations
986 operating on either side of the wireless link.
987 DWDS extends the normal WDS mechanism by leveraging existing security
988 protocols and eliminating static binding.
990 When DWDS is enabled on an access point 4-address frames received from
991 an authorized station will generate a ``DWDS discovery'' event to user
993 This event should be used to create a WDS interface that is bound
994 to the remote station (and usually plumbed into a bridge).
995 Once the WDS interface is up and running 4-address traffic then logically
996 flows through that interface.
998 When DWDS is enabled on a station, traffic with a destination address
999 different from the peer station are encapsulated in a 4-address frame
1000 and transmitted to the peer.
1001 All 4-address traffic uses the security information of the stations
1002 (e.g. cryptographic keys).
1003 A station is associated using 802.11n facilities may transport
1004 4-address traffic using these same mechanisms; this depends on available
1005 resources and capabilities of the device.
1006 The DWDS implementation guards against layer 2 routing loops of
1009 Enable the use of Atheros Fast Frames when communicating with
1010 another Fast Frames-capable station.
1011 Fast Frames are an encapsulation technique by which two 802.3
1012 frames are transmitted in a single 802.11 frame.
1013 This can noticeably improve throughput but requires that the
1014 receiving station understand how to decapsulate the frame.
1015 Fast frame use is negotiated using the Atheros 802.11 vendor-specific
1016 protocol extension so enabling use is safe when communicating with
1017 non-Atheros devices.
1018 By default, use of fast frames is enabled if the device is capable.
1019 To explicitly disable fast frames, use
1021 .It Cm fragthreshold Ar length
1022 Set the threshold for which transmitted frames are broken into fragments.
1025 argument is the frame size in bytes and must be in the range 256 to 2346.
1033 disables transmit fragmentation.
1034 Not all adapters honor the fragmentation threshold.
1036 When operating as an access point, do not broadcast the SSID
1037 in beacon frames or respond to probe request frames unless
1038 they are directed to the ap (i.e., they include the ap's SSID).
1039 By default, the SSID is included in beacon frames and
1040 undirected probe request frames are answered.
1041 To re-enable the broadcast of the SSID etc., use
1044 Enable use of High Throughput (HT) when using 802.11n (default).
1045 The 802.11n specification includes mechanisms for operation
1046 on 20MHz and 40MHz wide channels using different signalling mechanisms
1047 than specified in 802.11b, 802.11g, and 802.11a.
1048 Stations negotiate use of these facilities, termed HT20 and HT40,
1049 when they associate.
1050 To disable all use of 802.11n use
1052 To disable use of HT20 (e.g. to force only HT40 use) use
1054 To disable use of HT40 use
1057 HT configuration is used to ``auto promote'' operation
1058 when several choices are available.
1059 For example, if a station associates to an 11n-capable access point
1060 it controls whether the station uses legacy operation, HT20, or HT40.
1061 When an 11n-capable device is setup as an access point and
1062 Auto Channel Selection is used to locate a channel to operate on,
1063 HT configuration controls whether legacy, HT20, or HT40 operation is setup
1064 on the selected channel.
1065 If a fixed channel is specified for a station then HT configuration can
1066 be given as part of the channel specification; e.g. 6:ht/20 to setup
1067 HT20 operation on channel 6.
1069 Enable use of compatibility support for pre-802.11n devices (default).
1070 The 802.11n protocol specification went through several incompatible iterations.
1071 Some vendors implemented 11n support to older specifications that
1072 will not interoperate with a purely 11n-compliant station.
1073 In particular the information elements included in management frames
1074 for old devices are different.
1075 When compatibility support is enabled both standard and compatible data
1077 Stations that associate using the compatiblity mechanisms are flagged
1079 To disable compatiblity support use
1081 .It Cm htprotmode Ar technique
1082 For interfaces operating in 802.11n, use the specified
1084 for protecting HT frames in a mixed legacy/HT network.
1085 The set of valid techniques is
1090 Technique names are case insensitive.
1092 Enable inactivity processing for stations associated to an
1093 access point (default).
1094 When operating as an access point the 802.11 layer monitors
1095 the activity of each associated station.
1096 When a station is inactive for 5 minutes it will send several
1097 ``probe frames'' to see if the station is still present.
1098 If no response is received then the station is deauthenticated.
1099 Applications that prefer to handle this work can disable this
1103 Set the location to use in calculating regulatory constraints.
1104 The location is also advertised in beacon and probe response frames
1105 when 802.11d is enabled with
1114 Display the list of channels available for use taking into account
1115 any restrictions set with the
1118 See the description of
1120 for more information.
1122 Display the adaptor's capabilities, including the operating
1125 Display the list of channels available for use.
1126 Channels are shown with their IEEE channel number, equivalent
1127 frequency, and usage modes.
1128 Channels identified as
1133 Channels identified as
1135 may be used only for Atheros' Static Turbo mode
1137 . Cm mediaopt turbo ) .
1138 Channels marked with a
1140 have a regulatory constraint that they be passively scanned.
1141 This means a station is not permitted to transmit on the channel until
1142 it identifies the channel is being used for 802.11 communication;
1143 typically by hearing a beacon frame from an access point operating
1146 is another way of requesting this information.
1147 By default a compacted list of channels is displayed; if the
1149 option is specified then all channels are shown.
1150 .It Cm list countries
1151 Display the set of country codes and regulatory domains that can be
1152 used in regulatory configuration.
1154 Display the current MAC Access Control List state.
1155 Each address is prefixed with a character that indicates the
1156 current policy applied to it:
1158 indicates the address is allowed access,
1160 indicates the address is denied access,
1162 indicates the address is present but the current policy open
1163 (so the ACL is not consulted).
1165 Displays the mesh routing table, used for forwarding packets on a mesh
1167 .It Cm list regdomain
1168 Display the current regulatory settings including the available channels
1169 and transmit power caps.
1171 Display the parameters that govern roaming operation.
1173 Display the parameters that govern transmit operation.
1175 Display the transmit power caps for each channel.
1177 Display the access points and/or ad-hoc neighbors
1178 located in the vicinity.
1179 This information may be updated automatically by the adapter
1182 request or through background scanning.
1183 Depending on the capabilities of the stations the following
1184 flags can be included in the output:
1188 Indicates that the station is permitted to send/receive data frames.
1190 Extended Rate Phy (ERP).
1191 Indicates that the station is operating in an 802.11g network
1192 using extended transmit rates.
1194 High Throughput (HT).
1195 Indicates that the station is using HT transmit rates.
1196 If a `+' follows immediately after then the station associated
1197 using deprecated mechanisms supported only when
1202 Indicates that the station is operating in power save mode.
1204 Quality of Service (QoS).
1205 Indicates that the station is using QoS encapsulation for
1207 QoS encapsulation is enabled only when WME mode is enabled.
1209 Transitional Security Network (TSN).
1210 Indicates that the station associated using TSN; see also
1214 Wi-Fi Protected Setup (WPS).
1215 Indicates that the station associated using WPS.
1218 By default interesting information elements captured from the neighboring
1219 stations are displayed at the end of each row.
1220 Possible elements include:
1222 (station supports WME),
1224 (station supports WPA),
1226 (station supports WPS),
1228 (station supports 802.11i/RSN),
1230 (station supports 802.11n/HT communication),
1232 (station supports Atheros protocol extensions),
1234 (station supports unknown vendor-specific extensions).
1237 flag is used all the information elements and their
1238 contents will be shown.
1241 flag also enables display of long SSIDs.
1244 command is another way of requesting this information.
1246 When operating as an access point display the stations that are
1247 currently associated.
1248 When operating in ad-hoc mode display stations identified as
1249 neighbors in the IBSS.
1250 When operating in mesh mode display stations identified as
1251 neighbors in the MBSS.
1252 When operating in station mode display the access point.
1253 Capabilities advertised by the stations are described under
1257 Depending on the capabilities of the stations the following
1258 flags can be included in the output:
1262 Indicates that the station is permitted to send/receive data frames.
1264 Extended Rate Phy (ERP).
1265 Indicates that the station is operating in an 802.11g network
1266 using extended transmit rates.
1268 High Throughput (HT).
1269 Indicates that the station is using HT transmit rates.
1270 If a `+' follows immediately after then the station associated
1271 using deprecated mechanisms supported only when
1276 Indicates that the station is operating in power save mode.
1278 Quality of Service (QoS).
1279 Indicates that the station is using QoS encapsulation for
1281 QoS encapsulation is enabled only when WME mode is enabled.
1283 Transitional Security Network (TSN).
1284 Indicates that the station associated using TSN; see also
1288 Wi-Fi Protected Setup (WPS).
1289 Indicates that the station associated using WPS.
1292 By default information elements received from associated stations
1293 are displayed in a short form; the
1295 flag causes this information to be displayed symbolically.
1297 Display the current channel parameters to use when operating in WME mode.
1300 option is specified then both channel and BSS parameters are displayed
1301 for each AC (first channel, then BSS).
1302 When WME mode is enabled for an adaptor this information will be
1303 displayed with the regular status; this command is mostly useful
1304 for examining parameters when WME mode is disabled.
1305 See the description of the
1307 directive for information on the various parameters.
1308 .It Cm maxretry Ar count
1309 Set the maximum number of tries to use in sending unicast frames.
1310 The default setting is 6 but drivers may override this with a value
1312 .It Cm mcastrate Ar rate
1313 Set the rate for transmitting multicast/broadcast frames.
1314 Rates are specified as megabits/second in decimal; e.g.\& 5.5 for 5.5 Mb/s.
1315 This rate should be valid for the current operating conditions;
1316 if an invalid rate is specified drivers are free to chose an
1318 .It Cm mgtrate Ar rate
1319 Set the rate for transmitting management and/or control frames.
1320 Rates are specified as megabits/second in decimal; e.g.\& 5.5 for 5.5 Mb/s.
1322 Set the location to use in calculating regulatory constraints.
1323 The location is also advertised in beacon and probe response frames
1324 when 802.11d is enabled with
1333 Enable powersave operation.
1334 When operating as a client, the station will conserve power by
1335 periodically turning off the radio and listening for
1336 messages from the access point telling it there are packets waiting.
1337 The station must then retrieve the packets.
1338 Not all devices support power save operation as a client.
1339 The 802.11 specification requires that all access points support
1340 power save but some drivers do not.
1343 to disable powersave operation when operating as a client.
1344 .It Cm powersavesleep Ar sleep
1345 Set the desired max powersave sleep time in TU's (1024 usecs).
1346 By default the max powersave sleep time is 100 TU's.
1347 .It Cm protmode Ar technique
1348 For interfaces operating in 802.11g, use the specified
1350 for protecting OFDM frames in a mixed 11b/11g network.
1351 The set of valid techniques is
1357 Technique names are case insensitive.
1358 Not all devices support
1360 as a protection technique.
1362 When operating as an access point in 802.11g mode allow only
1363 11g-capable stations to associate (11b-only stations are not
1364 permitted to associate).
1365 To allow both 11g and 11b-only stations to associate, use
1368 When operating as an access point in 802.11n mode allow only
1369 HT-capable stations to associate (legacy stations are not
1370 permitted to associate).
1371 To allow both HT and legacy stations to associate, use
1373 .It Cm regdomain Ar sku
1374 Set the regulatory domain to use in calculating the regulatory constraints
1376 In particular the set of available channels, how the wireless device
1377 will operation on the channels, and the maximum transmit power that
1378 can be used on a channel are defined by this setting.
1379 Regdomain codes (SKU's) are taken from /etc/regdomain.xml and can also
1380 be viewed with the ``list countries'' request.
1381 Note that not all devices support changing the regdomain from a default
1382 setting; typically stored in EEPROM.
1390 Enable use of Reduced InterFrame Spacing (RIFS) when operating in 802.11n
1392 Note that RIFS must be supported by both the station and access point
1396 .It Cm roam:rate Ar rate
1397 Set the threshold for controlling roaming when operating in a BSS.
1400 parameter specifies the transmit rate in megabits
1401 at which roaming should be considered.
1402 If the current transmit rate drops below this setting and background scanning
1403 is enabled, then the system will check if a more desirable access point is
1404 available and switch over to it.
1405 The current scan cache contents are used if they are considered
1406 valid according to the
1408 parameter; otherwise a background scan operation is triggered before
1409 any selection occurs.
1410 Each channel type has a separate rate threshold; the default values are:
1411 12 Mb/s (11a), 2 Mb/s (11b), 2 Mb/s (11g), MCS 1 (11na, 11ng).
1412 .It Cm roam:rssi Ar rssi
1413 Set the threshold for controlling roaming when operating in a BSS.
1416 parameter specifies the receive signal strength in dBm units
1417 at which roaming should be considered.
1418 If the current rssi drops below this setting and background scanning
1419 is enabled, then the system will check if a more desirable access point is
1420 available and switch over to it.
1421 The current scan cache contents are used if they are considered
1422 valid according to the
1424 parameter; otherwise a background scan operation is triggered before
1425 any selection occurs.
1426 Each channel type has a separate rssi threshold; the default values are
1428 .It Cm roaming Ar mode
1429 When operating as a station, control how the system will
1430 behave when communication with the current access point
1434 argument may be one of
1436 (leave it to the hardware device to decide),
1438 (handle either in the device or the operating system\[em]as appropriate),
1440 (do nothing until explicitly instructed).
1441 By default, the device is left to handle this if it is
1442 capable; otherwise, the operating system will automatically
1443 attempt to reestablish communication.
1444 Manual mode is used by applications such as
1445 .Xr wpa_supplicant 8
1446 that want to control the selection of an access point.
1447 .It Cm rtsthreshold Ar length
1448 Set the threshold for which
1449 transmitted frames are preceded by transmission of an
1455 is the frame size in bytes and must be in the range 1 to 2346.
1463 disables transmission of RTS frames.
1464 Not all adapters support setting the RTS threshold.
1466 Initiate a scan of neighboring stations, wait for it to complete, and
1467 display all stations found.
1468 Only the super-user can initiate a scan.
1471 for information on the display.
1472 By default a background scan is done; otherwise a foreground
1473 scan is done and the station may roam to a different access point.
1476 request can be used to show recent scan results without
1477 initiating a new scan.
1478 .It Cm scanvalid Ar threshold
1479 Set the maximum time the scan cache contents are considered valid;
1480 i.e. will be used without first triggering a scan operation to
1484 parameter is specified in seconds and defaults to 60 seconds.
1485 The minimum setting for
1488 One should take care setting this threshold; if it is set too low
1489 then attempts to roam to another access point may trigger unnecessary
1490 background scan operations.
1492 Enable use of Short Guard Interval when operating in 802.11n
1494 NB: this currently enables Short GI on both HT40 and HT20 channels.
1495 To disable Short GI use
1498 Enable use of Static Spatial Multiplexing Power Save (SMPS)
1499 when operating in 802.11n.
1500 A station operating with Static SMPS maintains only a single
1501 receive chain active (this can significantly reduce power consumption).
1505 Enable use of Dynamic Spatial Multiplexing Power Save (SMPS)
1506 when operating in 802.11n.
1507 A station operating with Dynamic SMPS maintains only a single
1508 receive chain active but switches to multiple receive chains when it
1509 receives an RTS frame (this can significantly reduce power consumption).
1510 Note that stations cannot distinguish between RTS/CTS intended to
1511 enable multiple receive chains and those used for other purposes.
1515 Set the desired Service Set Identifier (aka network name).
1516 The SSID is a string up to 32 characters
1517 in length and may be specified as either a normal string or in
1518 hexadecimal when preceded by
1520 Additionally, the SSID may be cleared by setting it to
1522 .It Cm tdmaslot Ar slot
1523 When operating with TDMA, use the specified
1528 is a number between 0 and the maximum number of slots in the BSS.
1529 Note that a station configured as slot 0 is a master and
1530 will broadcast beacon frames advertising the BSS;
1531 stations configured to use other slots will always
1532 scan to locate a master before they ever transmit.
1536 .It Cm tdmaslotcnt Ar cnt
1537 When operating with TDMA, setup a BSS with
1540 The slot count may be at most 8.
1541 The current implementation is only tested with two stations
1542 (i.e. point to point applications).
1543 This setting is only meaningful when a station is configured as slot 0;
1544 other stations adopt this setting from the BSS they join.
1548 .It Cm tdmaslotlen Ar len
1549 When operating with TDMA, setup a BSS such that each station has a slot
1552 The slot length must be at least 150 microseconds (1/8 TU)
1553 and no more than 65 milliseconds.
1554 Note that setting too small a slot length may result in poor channel
1555 bandwidth utilization due to factors such as timer granularity and
1557 This setting is only meaningful when a station is configured as slot 0;
1558 other stations adopt this setting from the BSS they join.
1561 is set to 10 milliseconds.
1562 .It Cm tdmabintval Ar intval
1563 When operating with TDMA, setup a BSS such that beacons are transmitted every
1565 superframes to synchronize the TDMA slot timing.
1566 A superframe is defined as the number of slots times the slot length; e.g.
1567 a BSS with two slots of 10 milliseconds has a 20 millisecond superframe.
1568 The beacon interval may not be zero.
1571 causes the timers to be resynchronized more often; this can be help if
1572 significant timer drift is observed.
1577 When operating as an access point with WPA/802.11i allow legacy
1578 stations to associate using static key WEP and open authentication.
1579 To disallow legacy station use of WEP, use
1581 .It Cm txpower Ar power
1582 Set the power used to transmit frames.
1585 argument is specified in .5 dBm units.
1586 Out of range values are truncated.
1587 Typically only a few discreet power settings are available and
1588 the driver will use the setting closest to the specified value.
1589 Not all adapters support changing the transmit power.
1590 .It Cm ucastrate Ar rate
1591 Set a fixed rate for transmitting unicast frames.
1592 Rates are specified as megabits/second in decimal; e.g.\& 5.5 for 5.5 Mb/s.
1593 This rate should be valid for the current operating conditions;
1594 if an invalid rate is specified drivers are free to chose an
1596 .It Cm wepmode Ar mode
1597 Set the desired WEP mode.
1598 Not all adapters support all modes.
1599 The set of valid modes is
1605 mode explicitly tells the adaptor to allow association with access
1606 points which allow both encrypted and unencrypted traffic.
1609 means that the access point must only allow encrypted connections.
1612 is generally another name for
1614 Modes are case insensitive.
1615 .It Cm weptxkey Ar index
1616 Set the WEP key to be used for transmission.
1617 This is the same as setting the default transmission key with
1619 .It Cm wepkey Ar key Ns | Ns Ar index : Ns Ar key
1620 Set the selected WEP key.
1623 is not given, key 1 is set.
1624 A WEP key will be either 5 or 13
1625 characters (40 or 104 bits) depending of the local network and the
1626 capabilities of the adaptor.
1627 It may be specified either as a plain
1628 string or as a string of hexadecimal digits preceded by
1630 For maximum portability, hex keys are recommended;
1631 the mapping of text keys to WEP encryption is usually driver-specific.
1634 drivers do this mapping differently to
1636 A key may be cleared by setting it to
1638 If WEP is supported then there are at least four keys.
1639 Some adapters support more than four keys.
1640 If that is the case, then the first four keys
1641 (1-4) will be the standard temporary keys and any others will be adaptor
1642 specific keys such as permanent keys stored in NVRAM.
1644 Note that you must set a default transmit key with
1646 for the system to know which key to use in encrypting outbound traffic.
1648 Enable Wireless Multimedia Extensions (WME) support, if available,
1649 for the specified interface.
1650 WME is a subset of the IEEE 802.11e standard to support the
1651 efficient communication of realtime and multimedia data.
1652 To disable WME support, use
1654 Another name for this parameter is
1657 The following parameters are meaningful only when WME support is in use.
1658 Parameters are specified per-AC (Access Category) and
1659 split into those that are used by a station when acting
1660 as an access point and those for client stations in the BSS.
1661 The latter are received from the access point and may not be changed
1663 The following Access Categories are recognized:
1665 .Bl -tag -width ".Cm AC_BK" -compact
1669 best effort delivery,
1684 AC parameters are case-insensitive.
1685 Traffic classification is done in the operating system using the
1686 vlan priority associated with data frames or the
1687 ToS (Type of Service) indication in IP-encapsulated frames.
1688 If neither information is present, traffic is assigned to the
1689 Best Effort (BE) category.
1690 .Bl -tag -width indent
1692 Set the ACK policy for QoS transmissions by the local station;
1693 this controls whether or not data frames transmitted by a station
1694 require an ACK response from the receiving station.
1695 To disable waiting for an ACK use
1697 This parameter is applied only to the local station.
1699 Enable the Admission Control Mandatory (ACM) mechanism
1700 for transmissions by the local station.
1701 To disable the ACM use
1703 On stations in a BSS this parameter is read-only and indicates
1704 the setting received from the access point.
1705 NB: ACM is not supported right now.
1706 .It Cm aifs Ar ac Ar count
1707 Set the Arbitration Inter Frame Spacing (AIFS)
1708 channel access parameter to use for transmissions
1709 by the local station.
1710 On stations in a BSS this parameter is read-only and indicates
1711 the setting received from the access point.
1712 .It Cm cwmin Ar ac Ar count
1713 Set the CWmin channel access parameter to use for transmissions
1714 by the local station.
1715 On stations in a BSS this parameter is read-only and indicates
1716 the setting received from the access point.
1717 .It Cm cwmax Ar ac Ar count
1718 Set the CWmax channel access parameter to use for transmissions
1719 by the local station.
1720 On stations in a BSS this parameter is read-only and indicates
1721 the setting received from the access point.
1722 .It Cm txoplimit Ar ac Ar limit
1723 Set the Transmission Opportunity Limit channel access parameter
1724 to use for transmissions by the local station.
1725 This parameter defines an interval of time when a WME station
1726 has the right to initiate transmissions onto the wireless medium.
1727 On stations in a BSS this parameter is read-only and indicates
1728 the setting received from the access point.
1729 .It Cm bss:aifs Ar ac Ar count
1730 Set the AIFS channel access parameter to send to stations in a BSS.
1731 This parameter is meaningful only when operating in ap mode.
1732 .It Cm bss:cwmin Ar ac Ar count
1733 Set the CWmin channel access parameter to send to stations in a BSS.
1734 This parameter is meaningful only when operating in ap mode.
1735 .It Cm bss:cwmax Ar ac Ar count
1736 Set the CWmax channel access parameter to send to stations in a BSS.
1737 This parameter is meaningful only when operating in ap mode.
1738 .It Cm bss:txoplimit Ar ac Ar limit
1739 Set the TxOpLimit channel access parameter to send to stations in a BSS.
1740 This parameter is meaningful only when operating in ap mode.
1743 Enable Wireless Privacy Subscriber support.
1744 Note that WPS support requires a WPS-capable supplicant.
1745 To disable this function use
1749 The following parameters support an optional access control list
1750 feature available with some adapters when operating in ap mode; see
1752 This facility allows an access point to accept/deny association
1753 requests based on the MAC address of the station.
1754 Note that this feature does not significantly enhance security
1755 as MAC address spoofing is easy to do.
1756 .Bl -tag -width indent
1757 .It Cm mac:add Ar address
1758 Add the specified MAC address to the database.
1759 Depending on the policy setting association requests from the
1760 specified station will be allowed or denied.
1762 Set the ACL policy to permit association only by
1763 stations registered in the database.
1764 .It Cm mac:del Ar address
1765 Delete the specified MAC address from the database.
1767 Set the ACL policy to deny association only by
1768 stations registered in the database.
1769 .It Cm mac:kick Ar address
1770 Force the specified station to be deauthenticated.
1771 This typically is done to block a station after updating the
1774 Set the ACL policy to allow all stations to associate.
1776 Delete all entries in the database.
1778 Set the ACL policy to permit association only by
1779 stations approved by a RADIUS server.
1780 Note that this feature requires the
1782 program be configured to do the right thing
1783 as it handles the RADIUS processing
1784 (and marks stations as authorized).
1787 The following parameters are related to a wireless interface operating in mesh
1789 .Bl -tag -width indent
1790 .It Cm meshid Ar meshid
1791 Set the desired Mesh Identifier.
1792 The Mesh ID is a string up to 32 characters in length.
1793 A mesh interface must have a Mesh Identifier specified
1794 to reach an operational state.
1795 .It Cm meshttl Ar ttl
1796 Set the desired ``time to live'' for mesh forwarded packets;
1797 this is the number of hops a packet may be forwarded before
1799 The default setting for
1803 Enable or disable peering with neighbor mesh stations.
1804 Stations must peer before any data packets can be exchanged.
1809 Enable or disable forwarding packets by a mesh interface.
1813 .It Cm meshmetric Ar protocol
1816 as the link metric protocol used on a mesh network.
1817 The default protocol is called
1819 The mesh interface will restart after changing this setting.
1820 .It Cm meshpath Ar protocol
1823 as the path selection protocol used on a mesh network.
1824 The only available protocol at the moment is called
1826 (Hybrid Wireless Mesh Protocol).
1827 The mesh interface will restart after changing this setting.
1828 .It Cm hwmprootmode Ar mode
1829 Stations on a mesh network can operate as ``root nodes.''
1830 Root nodes try to find paths to all mesh nodes and advertise themselves
1832 When there is a root mesh node on a network, other mesh nodes can setup
1833 paths between themselves faster because they can use the root node
1834 to find the destination.
1835 This path may not be the best, but on-demand
1836 routing will eventually find the best path.
1837 The following modes are recognized:
1839 .Bl -tag -width ".Cm PROACTIVE" -compact
1843 Send broadcast path requests every two seconds.
1844 Nodes on the mesh without a path to this root mesh station with try to
1845 discover a path to us.
1847 Send broadcast path requests every two seconds and every node must reply with
1848 with a path reply even if it already has a path to this root mesh station,
1850 Send broadcast root annoucement (RANN) frames.
1851 Nodes on the mesh without a path to this root mesh station with try to
1852 discover a path to us.
1858 .It Cm hwmpmaxhops Ar cnt
1859 Set the maximum number of hops allowed in an HMWP path to
1861 The default setting for
1866 The following parameters are for compatibility with other systems:
1867 .Bl -tag -width indent
1869 Another name for the
1875 .It Cm stationname Ar name
1876 Set the name of this station.
1877 The station name is not part of the IEEE 802.11
1878 protocol though some interfaces support it.
1880 seems to be meaningful to identical or virtually identical equipment.
1881 Setting the station name is identical in syntax to setting the SSID.
1888 Another way of saying
1894 Another way of saying
1900 Another way of saying:
1901 .Dq Li "wepmode on weptxkey 1 wepkey 1:key wepkey 2:- wepkey 3:- wepkey 4:-" .
1907 .Ar n : k1 , k2 , k3 , k4
1910 Another way of saying
1911 .Dq Li "wepmode on weptxkey n wepkey 1:k1 wepkey 2:k2 wepkey 3:k3 wepkey 4:k4" .
1916 Another way of saying
1923 The following parameters are specific to bridge interfaces:
1924 .Bl -tag -width indent
1925 .It Cm addm Ar interface
1926 Add the interface named by
1928 as a member of the bridge.
1929 The interface is put into promiscuous mode
1930 so that it can receive every packet sent on the network.
1931 .It Cm deletem Ar interface
1932 Remove the interface named by
1935 Promiscuous mode is disabled on the interface when
1936 it is removed from the bridge.
1937 .It Cm maxaddr Ar size
1938 Set the size of the bridge address cache to
1940 The default is 100 entries.
1941 .It Cm timeout Ar seconds
1942 Set the timeout of address cache entries to
1947 is zero, then address cache entries will not be expired.
1948 The default is 1200 seconds.
1950 Display the addresses that have been learned by the bridge.
1951 .It Cm static Ar interface-name Ar address
1952 Add a static entry into the address cache pointing to
1953 .Ar interface-name .
1954 Static entries are never aged out of the cache or re-placed, even if the
1955 address is seen on a different interface.
1956 .It Cm deladdr Ar address
1959 from the address cache.
1961 Delete all dynamically-learned addresses from the address cache.
1963 Delete all addresses, including static addresses, from the address cache.
1964 .It Cm discover Ar interface
1965 Mark an interface as a
1968 When the bridge has no address cache entry
1969 (either dynamic or static)
1970 for the destination address of a packet,
1971 the bridge will forward the packet to all
1972 member interfaces marked as
1974 This is the default for all interfaces added to a bridge.
1975 .It Fl discover Ar interface
1978 attribute on a member interface.
1979 For packets without the
1981 attribute, the only packets forwarded on the interface are broadcast
1982 or multicast packets and packets for which the destination address
1983 is known to be on the interface's segment.
1984 .It Cm learn Ar interface
1985 Mark an interface as a
1988 When a packet arrives on such an interface, the source
1989 address of the packet is entered into the address cache as being a
1990 destination address on the interface's segment.
1991 This is the default for all interfaces added to a bridge.
1992 .It Fl learn Ar interface
1995 attribute on a member interface.
1996 .It Cm span Ar interface
1997 Add the interface named by
1999 as a span port on the bridge.
2000 Span ports transmit a copy of every frame received by the bridge.
2001 This is most useful for snooping a bridged network passively on
2002 another host connected to one of the span ports of the bridge.
2003 .It Fl span Ar interface
2004 Delete the interface named by
2006 from the list of span ports of the bridge.
2007 .It Cm stp Ar interface
2008 Enable Spanning Tree protocol on
2012 driver has support for the IEEE 802.1D Spanning Tree protocol (STP).
2013 Spanning Tree is used to detect and remove loops in a network topology.
2014 .It Fl stp Ar interface
2015 Disable Spanning Tree protocol on
2017 This is the default for all interfaces added to a bridge.
2018 .It Cm maxage Ar seconds
2019 Set the time that a Spanning Tree protocol configuration is valid.
2020 The default is 20 seconds.
2021 The minimum is 1 second and the maximum is 255 seconds.
2022 .It Cm fwddelay Ar seconds
2023 Set the time that must pass before an interface begins forwarding
2024 packets when Spanning Tree is enabled.
2025 The default is 15 seconds.
2026 The minimum is 1 second and the maximum is 255 seconds.
2027 .It Cm hellotime Ar seconds
2028 Set the time between broadcasting of Spanning Tree protocol
2029 configuration messages.
2030 The default is 2 seconds.
2031 The minimum is 1 second and the maximum is 255 seconds.
2032 .It Cm priority Ar value
2033 Set the bridge priority for Spanning Tree.
2034 The default is 32768.
2035 The minimum is 0 and the maximum is 65536.
2036 .It Cm ifpriority Ar interface Ar value
2037 Set the Spanning Tree priority of
2042 The minimum is 0 and the maximum is 255.
2043 .It Cm ifpathcost Ar interface Ar value
2044 Set the Spanning Tree path cost of
2049 The minimum is 0 and the maximum is 65535.
2052 The following parameters are specific to IP tunnel interfaces,
2054 .Bl -tag -width indent
2055 .It Cm tunnel Ar src_addr dest_addr
2056 Configure the physical source and destination address for IP tunnel
2062 are interpreted as the outer source/destination for the encapsulating
2065 Unconfigure the physical source and destination address for IP tunnel
2066 interfaces previously configured with
2069 Another name for the
2074 The following parameters are specific to
2077 .Bl -tag -width indent
2078 .It Cm vlan Ar vlan_tag
2079 Set the VLAN tag value to
2081 This value is a 16-bit number which is used to create an 802.1Q
2082 VLAN header for packets sent from the
2089 must both be set at the same time.
2090 .It Cm vlandev Ar iface
2091 Associate the physical interface
2096 Packets transmitted through the
2099 diverted to the specified physical interface
2101 with 802.1Q VLAN encapsulation.
2102 Packets with 802.1Q encapsulation received
2103 by the parent interface with the correct VLAN tag will be diverted to
2109 interface is assigned a
2110 copy of the parent interface's flags and the parent's ethernet address.
2115 must both be set at the same time.
2118 interface already has
2119 a physical interface associated with it, this command will fail.
2121 change the association to another physical interface, the existing
2122 association must be cleared first.
2124 Note: if the hardware tagging capability
2125 is set on the parent interface, the
2128 interface's behavior changes:
2131 interface recognizes that the
2132 parent interface supports insertion and extraction of VLAN tags on its
2133 own (usually in firmware) and that it should pass packets to and from
2134 the parent unaltered.
2135 .It Fl vlandev Op Ar iface
2138 pseudo device, disassociate the parent interface from it.
2139 This breaks the link between the
2141 interface and its parent,
2142 clears its VLAN tag, flags and its link address and shuts the interface down.
2145 argument is useless and hence deprecated.
2148 The following parameters are specific to
2151 .Bl -tag -width indent
2152 .It Cm advbase Ar seconds
2153 Specifies the base of the advertisement interval in seconds.
2154 The acceptable values are 1 to 255.
2155 The default value is 1.
2156 .\" The default value is
2157 .\" .Dv CARP_DFLTINTV .
2158 .It Cm advskew Ar interval
2159 Specifies the skew to add to the base advertisement interval to
2160 make one host advertise slower than another host.
2161 It is specified in 1/256 of seconds.
2162 The acceptable values are 1 to 254.
2163 The default value is 0.
2164 .It Cm pass Ar phrase
2165 Set the authentication key to
2168 Set the virtual host ID.
2169 This is a required setting.
2170 Acceptable values are 1 to 255.
2175 utility displays the current configuration for a network interface
2176 when no optional parameters are supplied.
2177 If a protocol family is specified,
2179 will report only the details specific to that protocol family.
2183 flag is passed before an interface name,
2185 will display the capability list and all
2186 of the supported media for the specified interface.
2189 flag is supplied, address lifetime is displayed for IPv6 addresses,
2190 as time offset string.
2194 flag may be used instead of an interface name.
2197 to display information about all interfaces in the system.
2200 flag limits this to interfaces that are down, and
2202 limits this to interfaces that are up.
2203 When no arguments are given,
2209 flag may be used to list all available interfaces on the system, with
2210 no other additional information.
2211 Use of this flag is mutually exclusive
2212 with all other flags and commands, except for
2214 (only list interfaces that are down)
2217 (only list interfaces that are up).
2221 flag may be used to get more verbose status for an interface.
2225 flag may be used to list all of the interface cloners available on
2226 the system, with no additional information.
2227 Use of this flag is mutually exclusive with all other flags and commands.
2231 flag causes keying information for the interface, if available, to be
2233 For example, the values of 802.11 WEP keys will be printed, if accessible to
2235 This information is not printed by default, as it may be considered
2238 Only the super-user may modify the configuration of a network interface.
2240 Messages indicating the specified interface does not exist, the
2241 requested address is unknown, or the user is not privileged and
2242 tried to alter an interface's configuration.
2260 Basic IPv6 node operation requires a link-local address on each
2261 interface configured for IPv6.
2262 Normally, such an address is automatically configured by the
2263 kernel on each interface added to the system; this behaviour may
2264 be disabled by setting the sysctl MIB variable
2265 .Va net.inet6.ip6.auto_linklocal
2268 If you delete such an address using
2270 the kernel may act very odd.
2271 Do this at your own risk.
projects / dragonfly.git / blob