2 * Copyright (c) 2002-2009 Sam Leffler, Errno Consulting
5 * Redistribution and use in source and binary forms, with or without
6 * modification, are permitted provided that the following conditions
8 * 1. Redistributions of source code must retain the above copyright
9 * notice, this list of conditions and the following disclaimer,
10 * without modification.
11 * 2. Redistributions in binary form must reproduce at minimum a disclaimer
12 * similar to the "NO WARRANTY" disclaimer below ("Disclaimer") and any
13 * redistribution must be conditioned upon including a substantially
14 * similar Disclaimer requirement for further binary redistribution.
17 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
18 * ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
19 * LIMITED TO, THE IMPLIED WARRANTIES OF NONINFRINGEMENT, MERCHANTIBILITY
20 * AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL
21 * THE COPYRIGHT HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY,
22 * OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
23 * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
24 * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER
25 * IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
26 * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
27 * THE POSSIBILITY OF SUCH DAMAGES.
29 * $FreeBSD: head/sys/dev/ath/if_ath.c 203751 2010-02-10 11:12:39Z rpaulo $");
33 * Driver for the Atheros Wireless LAN controller.
35 * This software is derived from work of Atsushi Onoe; his contribution
36 * is greatly appreciated.
43 #include <sys/param.h>
44 #include <sys/systm.h>
45 #include <sys/sysctl.h>
47 #include <sys/malloc.h>
49 #include <sys/mutex.h>
50 #include <sys/kernel.h>
51 #include <sys/socket.h>
52 #include <sys/sockio.h>
53 #include <sys/errno.h>
54 #include <sys/callout.h>
56 #include <sys/endian.h>
57 #include <sys/kthread.h>
58 #include <sys/taskqueue.h>
62 #include <net/if_dl.h>
63 #include <net/if_media.h>
64 #include <net/if_types.h>
65 #include <net/if_arp.h>
66 #include <net/if_llc.h>
67 #include <net/ifq_var.h>
69 #include <netproto/802_11/ieee80211_var.h>
70 #include <netproto/802_11/ieee80211_regdomain.h>
71 #ifdef IEEE80211_SUPPORT_SUPERG
72 #include <netproto/802_11/ieee80211_superg.h>
74 #ifdef IEEE80211_SUPPORT_TDMA
75 #include <netproto/802_11/ieee80211_tdma.h>
81 #include <netinet/in.h>
82 #include <netinet/if_ether.h>
85 #include <dev/netif/ath/ath/if_athvar.h>
86 #include <dev/netif/ath/hal/ath_hal/ah_devid.h> /* XXX for softled */
89 #include <dev/netif/ath_tx99/ath_tx99.h>
93 * ATH_BCBUF determines the number of vap's that can transmit
94 * beacons and also (currently) the number of vap's that can
95 * have unique mac addresses/bssid. When staggering beacons
96 * 4 is probably a good max as otherwise the beacons become
97 * very closely spaced and there is limited time for cab q traffic
98 * to go out. You can burst beacons instead but that is not good
99 * for stations in power save and at some point you really want
100 * another radio (and channel).
102 * The limit on the number of mac addresses is tied to our use of
103 * the U/L bit and tracking addresses in a byte; it would be
104 * worthwhile to allow more for applications like proxy sta.
106 CTASSERT(ATH_BCBUF <= 8);
108 /* unaligned little endian access */
109 #define LE_READ_2(p) \
111 ((((u_int8_t *)(p))[0] ) | (((u_int8_t *)(p))[1] << 8)))
112 #define LE_READ_4(p) \
114 ((((u_int8_t *)(p))[0] ) | (((u_int8_t *)(p))[1] << 8) | \
115 (((u_int8_t *)(p))[2] << 16) | (((u_int8_t *)(p))[3] << 24)))
117 static struct ieee80211vap *ath_vap_create(struct ieee80211com *,
118 const char name[IFNAMSIZ], int unit, int opmode,
119 int flags, const uint8_t bssid[IEEE80211_ADDR_LEN],
120 const uint8_t mac[IEEE80211_ADDR_LEN]);
121 static void ath_vap_delete(struct ieee80211vap *);
122 static void ath_init(void *);
123 static void ath_stop_locked(struct ifnet *);
124 static void ath_stop(struct ifnet *);
125 static void ath_start(struct ifnet *);
126 static int ath_reset(struct ifnet *);
127 static int ath_reset_vap(struct ieee80211vap *, u_long);
128 static int ath_media_change(struct ifnet *);
129 static void ath_watchdog_callout(void *);
130 static int ath_ioctl(struct ifnet *, u_long, caddr_t, struct ucred *);
131 static void ath_fatal_proc(void *, int);
132 static void ath_bmiss_vap(struct ieee80211vap *);
133 static void ath_bmiss_task(void *, int);
134 static int ath_keyset(struct ath_softc *, const struct ieee80211_key *,
135 struct ieee80211_node *);
136 static int ath_key_alloc(struct ieee80211vap *,
137 struct ieee80211_key *,
138 ieee80211_keyix *, ieee80211_keyix *);
139 static int ath_key_delete(struct ieee80211vap *,
140 const struct ieee80211_key *);
141 static int ath_key_set(struct ieee80211vap *, const struct ieee80211_key *,
142 const u_int8_t mac[IEEE80211_ADDR_LEN]);
143 static void ath_key_update_begin(struct ieee80211vap *);
144 static void ath_key_update_end(struct ieee80211vap *);
145 static void ath_update_mcast(struct ifnet *);
146 static void ath_update_promisc(struct ifnet *);
147 static void ath_mode_init(struct ath_softc *);
148 static void ath_setslottime(struct ath_softc *);
149 static void ath_updateslot(struct ifnet *);
150 static int ath_beaconq_setup(struct ath_hal *);
151 static int ath_beacon_alloc(struct ath_softc *, struct ieee80211_node *);
152 static void ath_beacon_update(struct ieee80211vap *, int item);
153 static void ath_beacon_setup(struct ath_softc *, struct ath_buf *);
154 static void ath_beacon_proc(void *, int);
155 static struct ath_buf *ath_beacon_generate(struct ath_softc *,
156 struct ieee80211vap *);
157 static void ath_bstuck_task(void *, int);
158 static void ath_beacon_return(struct ath_softc *, struct ath_buf *);
159 static void ath_beacon_free(struct ath_softc *);
160 static void ath_beacon_config(struct ath_softc *, struct ieee80211vap *);
161 static void ath_descdma_cleanup(struct ath_softc *sc,
162 struct ath_descdma *, ath_bufhead *);
163 static int ath_desc_alloc(struct ath_softc *);
164 static void ath_desc_free(struct ath_softc *);
165 static struct ieee80211_node *ath_node_alloc(struct ieee80211vap *,
166 const uint8_t [IEEE80211_ADDR_LEN]);
167 static void ath_node_free(struct ieee80211_node *);
168 static void ath_node_getsignal(const struct ieee80211_node *,
170 static int ath_rxbuf_init(struct ath_softc *, struct ath_buf *);
171 static void ath_recv_mgmt(struct ieee80211_node *ni, struct mbuf *m,
172 int subtype, int rssi, int nf);
173 static void ath_setdefantenna(struct ath_softc *, u_int);
174 static void ath_rx_task(void *, int);
175 static void ath_txq_init(struct ath_softc *sc, struct ath_txq *, int);
176 static struct ath_txq *ath_txq_setup(struct ath_softc*, int qtype, int subtype);
177 static int ath_tx_setup(struct ath_softc *, int, int);
178 static int ath_wme_update(struct ieee80211com *);
179 static void ath_tx_cleanupq(struct ath_softc *, struct ath_txq *);
180 static void ath_tx_cleanup(struct ath_softc *);
181 static void ath_freetx(struct mbuf *);
182 static int ath_tx_start(struct ath_softc *, struct ieee80211_node *,
183 struct ath_buf *, struct mbuf *);
184 static void ath_tx_task_q0(void *, int);
185 static void ath_tx_task_q0123(void *, int);
186 static void ath_tx_task(void *, int);
187 static void ath_tx_draintxq(struct ath_softc *, struct ath_txq *);
188 static int ath_chan_set(struct ath_softc *, struct ieee80211_channel *);
189 static void ath_draintxq(struct ath_softc *);
190 static void ath_stoprecv(struct ath_softc *);
191 static int ath_startrecv(struct ath_softc *);
192 static void ath_chan_change(struct ath_softc *, struct ieee80211_channel *);
193 static void ath_scan_start(struct ieee80211com *);
194 static void ath_scan_end(struct ieee80211com *);
195 static void ath_set_channel(struct ieee80211com *);
196 static void ath_calibrate_callout(void *);
197 static int ath_newstate(struct ieee80211vap *, enum ieee80211_state, int);
198 static void ath_setup_stationkey(struct ieee80211_node *);
199 static void ath_newassoc(struct ieee80211_node *, int);
200 static int ath_setregdomain(struct ieee80211com *,
201 struct ieee80211_regdomain *, int,
202 struct ieee80211_channel []);
203 static void ath_getradiocaps(struct ieee80211com *, int, int *,
204 struct ieee80211_channel []);
205 static int ath_getchannels(struct ath_softc *);
206 static void ath_led_event(struct ath_softc *, int);
208 static int ath_rate_setup(struct ath_softc *, u_int mode);
209 static void ath_setcurmode(struct ath_softc *, enum ieee80211_phymode);
211 static void ath_sysctlattach(struct ath_softc *);
212 static int ath_raw_xmit(struct ieee80211_node *,
213 struct mbuf *, const struct ieee80211_bpf_params *);
214 static void ath_announce(struct ath_softc *);
215 static void ath_sysctl_stats_attach(struct ath_softc *sc);
217 #ifdef IEEE80211_SUPPORT_TDMA
218 static void ath_tdma_settimers(struct ath_softc *sc, u_int32_t nexttbtt,
220 static void ath_tdma_bintvalsetup(struct ath_softc *sc,
221 const struct ieee80211_tdma_state *tdma);
222 static void ath_tdma_config(struct ath_softc *sc, struct ieee80211vap *vap);
223 static void ath_tdma_update(struct ieee80211_node *ni,
224 const struct ieee80211_tdma_param *tdma, int);
225 static void ath_tdma_beacon_send(struct ath_softc *sc,
226 struct ieee80211vap *vap);
229 ath_hal_setcca(struct ath_hal *ah, int ena)
232 * NB: fill me in; this is not provided by default because disabling
233 * CCA in most locales violates regulatory.
238 ath_hal_getcca(struct ath_hal *ah)
241 if (ath_hal_getcapability(ah, HAL_CAP_DIAG, 0, &diag) != HAL_OK)
243 return ((diag & 0x500000) == 0);
246 #define TDMA_EP_MULTIPLIER (1<<10) /* pow2 to optimize out * and / */
247 #define TDMA_LPF_LEN 6
248 #define TDMA_DUMMY_MARKER 0x127
249 #define TDMA_EP_MUL(x, mul) ((x) * (mul))
250 #define TDMA_IN(x) (TDMA_EP_MUL((x), TDMA_EP_MULTIPLIER))
251 #define TDMA_LPF(x, y, len) \
252 ((x != TDMA_DUMMY_MARKER) ? (((x) * ((len)-1) + (y)) / (len)) : (y))
253 #define TDMA_SAMPLE(x, y) do { \
254 x = TDMA_LPF((x), TDMA_IN(y), TDMA_LPF_LEN); \
256 #define TDMA_EP_RND(x,mul) \
257 ((((x)%(mul)) >= ((mul)/2)) ? ((x) + ((mul) - 1)) / (mul) : (x)/(mul))
258 #define TDMA_AVG(x) TDMA_EP_RND(x, TDMA_EP_MULTIPLIER)
259 #endif /* IEEE80211_SUPPORT_TDMA */
261 SYSCTL_DECL(_hw_ath);
263 /* XXX validate sysctl values */
264 static int ath_longcalinterval = 30; /* long cals every 30 secs */
265 SYSCTL_INT(_hw_ath, OID_AUTO, longcal, CTLFLAG_RW, &ath_longcalinterval,
266 0, "long chip calibration interval (secs)");
267 static int ath_shortcalinterval = 100; /* short cals every 100 ms */
268 SYSCTL_INT(_hw_ath, OID_AUTO, shortcal, CTLFLAG_RW, &ath_shortcalinterval,
269 0, "short chip calibration interval (msecs)");
270 static int ath_resetcalinterval = 20*60; /* reset cal state 20 mins */
271 SYSCTL_INT(_hw_ath, OID_AUTO, resetcal, CTLFLAG_RW, &ath_resetcalinterval,
272 0, "reset chip calibration results (secs)");
274 static int ath_rxbuf = ATH_RXBUF; /* # rx buffers to allocate */
275 SYSCTL_INT(_hw_ath, OID_AUTO, rxbuf, CTLFLAG_RW, &ath_rxbuf,
276 0, "rx buffers allocated");
277 TUNABLE_INT("hw.ath.rxbuf", &ath_rxbuf);
278 static int ath_txbuf = ATH_TXBUF; /* # tx buffers to allocate */
279 SYSCTL_INT(_hw_ath, OID_AUTO, txbuf, CTLFLAG_RW, &ath_txbuf,
280 0, "tx buffers allocated");
281 TUNABLE_INT("hw.ath.txbuf", &ath_txbuf);
283 static int ath_bstuck_threshold = 4; /* max missed beacons */
284 SYSCTL_INT(_hw_ath, OID_AUTO, bstuck, CTLFLAG_RW, &ath_bstuck_threshold,
285 0, "max missed beacon xmits before chip reset");
289 ATH_DEBUG_XMIT = 0x00000001, /* basic xmit operation */
290 ATH_DEBUG_XMIT_DESC = 0x00000002, /* xmit descriptors */
291 ATH_DEBUG_RECV = 0x00000004, /* basic recv operation */
292 ATH_DEBUG_RECV_DESC = 0x00000008, /* recv descriptors */
293 ATH_DEBUG_RATE = 0x00000010, /* rate control */
294 ATH_DEBUG_RESET = 0x00000020, /* reset processing */
295 ATH_DEBUG_MODE = 0x00000040, /* mode init/setup */
296 ATH_DEBUG_BEACON = 0x00000080, /* beacon handling */
297 ATH_DEBUG_WATCHDOG = 0x00000100, /* watchdog timeout */
298 ATH_DEBUG_INTR = 0x00001000, /* ISR */
299 ATH_DEBUG_TX_PROC = 0x00002000, /* tx ISR proc */
300 ATH_DEBUG_RX_PROC = 0x00004000, /* rx ISR proc */
301 ATH_DEBUG_BEACON_PROC = 0x00008000, /* beacon ISR proc */
302 ATH_DEBUG_CALIBRATE = 0x00010000, /* periodic calibration */
303 ATH_DEBUG_KEYCACHE = 0x00020000, /* key cache management */
304 ATH_DEBUG_STATE = 0x00040000, /* 802.11 state transitions */
305 ATH_DEBUG_NODE = 0x00080000, /* node management */
306 ATH_DEBUG_LED = 0x00100000, /* led management */
307 ATH_DEBUG_FF = 0x00200000, /* fast frames */
308 ATH_DEBUG_DFS = 0x00400000, /* DFS processing */
309 ATH_DEBUG_TDMA = 0x00800000, /* TDMA processing */
310 ATH_DEBUG_TDMA_TIMER = 0x01000000, /* TDMA timer processing */
311 ATH_DEBUG_REGDOMAIN = 0x02000000, /* regulatory processing */
312 ATH_DEBUG_FATAL = 0x80000000, /* fatal errors */
313 ATH_DEBUG_ANY = 0xffffffff
315 static int ath_debug = 0;
316 SYSCTL_INT(_hw_ath, OID_AUTO, debug, CTLFLAG_RW, &ath_debug,
317 0, "control debugging printfs");
318 TUNABLE_INT("hw.ath.debug", &ath_debug);
320 #define IFF_DUMPPKTS(sc, m) \
321 ((sc->sc_debug & (m)) || \
322 (sc->sc_ifp->if_flags & (IFF_DEBUG|IFF_LINK2)) == (IFF_DEBUG|IFF_LINK2))
323 #define DPRINTF(sc, m, fmt, ...) do { \
324 if (sc->sc_debug & (m)) \
325 kprintf(fmt, __VA_ARGS__); \
327 #define KEYPRINTF(sc, ix, hk, mac) do { \
328 if (sc->sc_debug & ATH_DEBUG_KEYCACHE) \
329 ath_keyprint(sc, __func__, ix, hk, mac); \
331 static void ath_printrxbuf(struct ath_softc *, const struct ath_buf *bf,
333 static void ath_printtxbuf(struct ath_softc *, const struct ath_buf *bf,
334 u_int qnum, u_int ix, int done);
336 #define IFF_DUMPPKTS(sc, m) \
337 ((sc->sc_ifp->if_flags & (IFF_DEBUG|IFF_LINK2)) == (IFF_DEBUG|IFF_LINK2))
338 #define DPRINTF(sc, m, fmt, ...) do { \
341 #define KEYPRINTF(sc, k, ix, mac) do { \
346 MALLOC_DEFINE(M_ATHDEV, "athdev", "ath driver dma buffers");
349 ath_attach(u_int16_t devid, struct ath_softc *sc)
352 struct ieee80211com *ic;
353 struct ath_hal *ah = NULL;
357 uint8_t macaddr[IEEE80211_ADDR_LEN];
359 DPRINTF(sc, ATH_DEBUG_ANY, "%s: devid 0x%x\n", __func__, devid);
361 ifp = sc->sc_ifp = if_alloc(IFT_IEEE80211);
363 device_printf(sc->sc_dev, "can not if_alloc()\n");
369 /* set these up early for if_printf use */
370 if_initname(ifp, device_get_name(sc->sc_dev),
371 device_get_unit(sc->sc_dev));
373 /* prepare sysctl tree for use in sub modules */
374 sysctl_ctx_init(&sc->sc_sysctl_ctx);
375 sc->sc_sysctl_tree = SYSCTL_ADD_NODE(&sc->sc_sysctl_ctx,
376 SYSCTL_STATIC_CHILDREN(_hw),
378 device_get_nameunit(sc->sc_dev),
381 ah = ath_hal_attach(devid, sc, sc->sc_st, sc->sc_sh, &status);
383 if_printf(ifp, "unable to attach hardware; HAL status %u\n",
389 sc->sc_invalid = 0; /* ready to go, enable interrupt handling */
391 sc->sc_debug = ath_debug;
395 * Check if the MAC has multi-rate retry support.
396 * We do this by trying to setup a fake extended
397 * descriptor. MAC's that don't have support will
398 * return false w/o doing anything. MAC's that do
399 * support it will return true w/o doing anything.
401 sc->sc_mrretry = ath_hal_setupxtxdesc(ah, NULL, 0,0, 0,0, 0,0);
404 * Check if the device has hardware counters for PHY
405 * errors. If so we need to enable the MIB interrupt
406 * so we can act on stat triggers.
408 if (ath_hal_hwphycounters(ah))
412 * Get the hardware key cache size.
414 sc->sc_keymax = ath_hal_keycachesize(ah);
415 if (sc->sc_keymax > ATH_KEYMAX) {
416 if_printf(ifp, "Warning, using only %u of %u key cache slots\n",
417 ATH_KEYMAX, sc->sc_keymax);
418 sc->sc_keymax = ATH_KEYMAX;
421 * Reset the key cache since some parts do not
422 * reset the contents on initial power up.
424 for (i = 0; i < sc->sc_keymax; i++)
425 ath_hal_keyreset(ah, i);
428 * Collect the default channel list.
430 error = ath_getchannels(sc);
435 * Setup rate tables for all potential media types.
437 ath_rate_setup(sc, IEEE80211_MODE_11A);
438 ath_rate_setup(sc, IEEE80211_MODE_11B);
439 ath_rate_setup(sc, IEEE80211_MODE_11G);
440 ath_rate_setup(sc, IEEE80211_MODE_TURBO_A);
441 ath_rate_setup(sc, IEEE80211_MODE_TURBO_G);
442 ath_rate_setup(sc, IEEE80211_MODE_STURBO_A);
443 ath_rate_setup(sc, IEEE80211_MODE_11NA);
444 ath_rate_setup(sc, IEEE80211_MODE_11NG);
445 ath_rate_setup(sc, IEEE80211_MODE_HALF);
446 ath_rate_setup(sc, IEEE80211_MODE_QUARTER);
448 /* NB: setup here so ath_rate_update is happy */
449 ath_setcurmode(sc, IEEE80211_MODE_11A);
452 * Allocate tx+rx descriptors and populate the lists.
454 wlan_assert_serialized();
455 wlan_serialize_exit();
456 error = ath_desc_alloc(sc);
457 wlan_serialize_enter();
459 if_printf(ifp, "failed to allocate descriptors: %d\n", error);
462 callout_init(&sc->sc_cal_ch);
463 callout_init(&sc->sc_wd_ch);
465 sc->sc_tq = taskqueue_create("ath_taskq", M_INTWAIT,
466 taskqueue_thread_enqueue, &sc->sc_tq);
467 taskqueue_start_threads(&sc->sc_tq, 1, TDPRI_KERN_DAEMON, -1,
468 "%s taskq", ifp->if_xname);
470 TASK_INIT(&sc->sc_rxtask, 0, ath_rx_task, sc);
471 TASK_INIT(&sc->sc_bmisstask, 0, ath_bmiss_task, sc);
472 TASK_INIT(&sc->sc_bstucktask,0, ath_bstuck_task, sc);
475 * Allocate hardware transmit queues: one queue for
476 * beacon frames and one data queue for each QoS
477 * priority. Note that the hal handles reseting
478 * these queues at the needed time.
482 sc->sc_bhalq = ath_beaconq_setup(ah);
483 if (sc->sc_bhalq == (u_int) -1) {
484 if_printf(ifp, "unable to setup a beacon xmit queue!\n");
488 sc->sc_cabq = ath_txq_setup(sc, HAL_TX_QUEUE_CAB, 0);
489 if (sc->sc_cabq == NULL) {
490 if_printf(ifp, "unable to setup CAB xmit queue!\n");
494 /* NB: insure BK queue is the lowest priority h/w queue */
495 if (!ath_tx_setup(sc, WME_AC_BK, HAL_WME_AC_BK)) {
496 if_printf(ifp, "unable to setup xmit queue for %s traffic!\n",
497 ieee80211_wme_acnames[WME_AC_BK]);
501 if (!ath_tx_setup(sc, WME_AC_BE, HAL_WME_AC_BE) ||
502 !ath_tx_setup(sc, WME_AC_VI, HAL_WME_AC_VI) ||
503 !ath_tx_setup(sc, WME_AC_VO, HAL_WME_AC_VO)) {
505 * Not enough hardware tx queues to properly do WME;
506 * just punt and assign them all to the same h/w queue.
507 * We could do a better job of this if, for example,
508 * we allocate queues when we switch from station to
511 if (sc->sc_ac2q[WME_AC_VI] != NULL)
512 ath_tx_cleanupq(sc, sc->sc_ac2q[WME_AC_VI]);
513 if (sc->sc_ac2q[WME_AC_BE] != NULL)
514 ath_tx_cleanupq(sc, sc->sc_ac2q[WME_AC_BE]);
515 sc->sc_ac2q[WME_AC_BE] = sc->sc_ac2q[WME_AC_BK];
516 sc->sc_ac2q[WME_AC_VI] = sc->sc_ac2q[WME_AC_BK];
517 sc->sc_ac2q[WME_AC_VO] = sc->sc_ac2q[WME_AC_BK];
521 * Special case certain configurations. Note the
522 * CAB queue is handled by these specially so don't
523 * include them when checking the txq setup mask.
525 switch (sc->sc_txqsetup &~ (1<<sc->sc_cabq->axq_qnum)) {
527 TASK_INIT(&sc->sc_txtask, 0, ath_tx_task_q0, sc);
530 TASK_INIT(&sc->sc_txtask, 0, ath_tx_task_q0123, sc);
533 TASK_INIT(&sc->sc_txtask, 0, ath_tx_task, sc);
538 * Setup rate control. Some rate control modules
539 * call back to change the anntena state so expose
540 * the necessary entry points.
541 * XXX maybe belongs in struct ath_ratectrl?
543 sc->sc_setdefantenna = ath_setdefantenna;
544 sc->sc_rc = ath_rate_attach(sc);
545 if (sc->sc_rc == NULL) {
552 sc->sc_ledon = 0; /* low true */
553 sc->sc_ledidle = (2700*hz)/1000; /* 2.7sec */
554 callout_init_mp(&sc->sc_ledtimer);
556 * Auto-enable soft led processing for IBM cards and for
557 * 5211 minipci cards. Users can also manually enable/disable
558 * support with a sysctl.
560 sc->sc_softled = (devid == AR5212_DEVID_IBM || devid == AR5211_DEVID);
561 if (sc->sc_softled) {
562 ath_hal_gpioCfgOutput(ah, sc->sc_ledpin,
563 HAL_GPIO_MUX_MAC_NETWORK_LED);
564 ath_hal_gpioset(ah, sc->sc_ledpin, !sc->sc_ledon);
568 ifp->if_flags = IFF_SIMPLEX | IFF_BROADCAST | IFF_MULTICAST;
569 ifp->if_start = ath_start;
570 ifp->if_ioctl = ath_ioctl;
571 ifp->if_init = ath_init;
572 ifq_set_maxlen(&ifp->if_snd, IFQ_MAXLEN);
573 ifq_set_ready(&ifp->if_snd);
576 /* XXX not right but it's not used anywhere important */
577 ic->ic_phytype = IEEE80211_T_OFDM;
578 ic->ic_opmode = IEEE80211_M_STA;
580 IEEE80211_C_STA /* station mode */
581 | IEEE80211_C_IBSS /* ibss, nee adhoc, mode */
582 | IEEE80211_C_HOSTAP /* hostap mode */
583 | IEEE80211_C_MONITOR /* monitor mode */
584 | IEEE80211_C_AHDEMO /* adhoc demo mode */
585 | IEEE80211_C_WDS /* 4-address traffic works */
586 | IEEE80211_C_MBSS /* mesh point link mode */
587 | IEEE80211_C_SHPREAMBLE /* short preamble supported */
588 | IEEE80211_C_SHSLOT /* short slot time supported */
589 | IEEE80211_C_WPA /* capable of WPA1+WPA2 */
590 | IEEE80211_C_BGSCAN /* capable of bg scanning */
591 | IEEE80211_C_TXFRAG /* handle tx frags */
594 * Query the hal to figure out h/w crypto support.
596 if (ath_hal_ciphersupported(ah, HAL_CIPHER_WEP))
597 ic->ic_cryptocaps |= IEEE80211_CRYPTO_WEP;
598 if (ath_hal_ciphersupported(ah, HAL_CIPHER_AES_OCB))
599 ic->ic_cryptocaps |= IEEE80211_CRYPTO_AES_OCB;
600 if (ath_hal_ciphersupported(ah, HAL_CIPHER_AES_CCM))
601 ic->ic_cryptocaps |= IEEE80211_CRYPTO_AES_CCM;
602 if (ath_hal_ciphersupported(ah, HAL_CIPHER_CKIP))
603 ic->ic_cryptocaps |= IEEE80211_CRYPTO_CKIP;
604 if (ath_hal_ciphersupported(ah, HAL_CIPHER_TKIP)) {
605 ic->ic_cryptocaps |= IEEE80211_CRYPTO_TKIP;
607 * Check if h/w does the MIC and/or whether the
608 * separate key cache entries are required to
609 * handle both tx+rx MIC keys.
611 if (ath_hal_ciphersupported(ah, HAL_CIPHER_MIC))
612 ic->ic_cryptocaps |= IEEE80211_CRYPTO_TKIPMIC;
614 * If the h/w supports storing tx+rx MIC keys
615 * in one cache slot automatically enable use.
617 if (ath_hal_hastkipsplit(ah) ||
618 !ath_hal_settkipsplit(ah, AH_FALSE))
621 * If the h/w can do TKIP MIC together with WME then
622 * we use it; otherwise we force the MIC to be done
623 * in software by the net80211 layer.
625 if (ath_hal_haswmetkipmic(ah))
626 sc->sc_wmetkipmic = 1;
628 sc->sc_hasclrkey = ath_hal_ciphersupported(ah, HAL_CIPHER_CLR);
630 * Check for multicast key search support.
632 if (ath_hal_hasmcastkeysearch(sc->sc_ah) &&
633 !ath_hal_getmcastkeysearch(sc->sc_ah)) {
634 ath_hal_setmcastkeysearch(sc->sc_ah, 1);
636 sc->sc_mcastkey = ath_hal_getmcastkeysearch(ah);
638 * Mark key cache slots associated with global keys
639 * as in use. If we knew TKIP was not to be used we
640 * could leave the +32, +64, and +32+64 slots free.
642 for (i = 0; i < IEEE80211_WEP_NKID; i++) {
643 setbit(sc->sc_keymap, i);
644 setbit(sc->sc_keymap, i+64);
645 if (sc->sc_splitmic) {
646 setbit(sc->sc_keymap, i+32);
647 setbit(sc->sc_keymap, i+32+64);
651 * TPC support can be done either with a global cap or
652 * per-packet support. The latter is not available on
653 * all parts. We're a bit pedantic here as all parts
654 * support a global cap.
656 if (ath_hal_hastpc(ah) || ath_hal_hastxpowlimit(ah))
657 ic->ic_caps |= IEEE80211_C_TXPMGT;
660 * Mark WME capability only if we have sufficient
661 * hardware queues to do proper priority scheduling.
663 if (sc->sc_ac2q[WME_AC_BE] != sc->sc_ac2q[WME_AC_BK])
664 ic->ic_caps |= IEEE80211_C_WME;
666 * Check for misc other capabilities.
668 if (ath_hal_hasbursting(ah))
669 ic->ic_caps |= IEEE80211_C_BURST;
670 sc->sc_hasbmask = ath_hal_hasbssidmask(ah);
671 sc->sc_hasbmatch = ath_hal_hasbssidmatch(ah);
672 sc->sc_hastsfadd = ath_hal_hastsfadjust(ah);
673 if (ath_hal_hasfastframes(ah))
674 ic->ic_caps |= IEEE80211_C_FF;
675 wmodes = ath_hal_getwirelessmodes(ah);
676 if (wmodes & (HAL_MODE_108G|HAL_MODE_TURBO))
677 ic->ic_caps |= IEEE80211_C_TURBOP;
678 #ifdef IEEE80211_SUPPORT_TDMA
679 if (ath_hal_macversion(ah) > 0x78) {
680 ic->ic_caps |= IEEE80211_C_TDMA; /* capable of TDMA */
681 ic->ic_tdma_update = ath_tdma_update;
685 * Indicate we need the 802.11 header padded to a
686 * 32-bit boundary for 4-address and QoS frames.
688 ic->ic_flags |= IEEE80211_F_DATAPAD;
691 * Query the hal about antenna support.
693 sc->sc_defant = ath_hal_getdefantenna(ah);
696 * Not all chips have the VEOL support we want to
697 * use with IBSS beacons; check here for it.
699 sc->sc_hasveol = ath_hal_hasveol(ah);
701 /* get mac address from hardware */
702 ath_hal_getmac(ah, macaddr);
704 ath_hal_getbssidmask(ah, sc->sc_hwbssidmask);
706 /* NB: used to size node table key mapping array */
707 ic->ic_max_keyix = sc->sc_keymax;
708 /* call MI attach routine. */
709 ieee80211_ifattach(ic, macaddr);
710 ic->ic_setregdomain = ath_setregdomain;
711 ic->ic_getradiocaps = ath_getradiocaps;
712 sc->sc_opmode = HAL_M_STA;
714 /* override default methods */
715 ic->ic_newassoc = ath_newassoc;
716 ic->ic_updateslot = ath_updateslot;
717 ic->ic_wme.wme_update = ath_wme_update;
718 ic->ic_vap_create = ath_vap_create;
719 ic->ic_vap_delete = ath_vap_delete;
720 ic->ic_raw_xmit = ath_raw_xmit;
721 ic->ic_update_mcast = ath_update_mcast;
722 ic->ic_update_promisc = ath_update_promisc;
723 ic->ic_node_alloc = ath_node_alloc;
724 sc->sc_node_free = ic->ic_node_free;
725 ic->ic_node_free = ath_node_free;
726 ic->ic_node_getsignal = ath_node_getsignal;
727 ic->ic_scan_start = ath_scan_start;
728 ic->ic_scan_end = ath_scan_end;
729 ic->ic_set_channel = ath_set_channel;
731 ieee80211_radiotap_attach(ic,
732 &sc->sc_tx_th.wt_ihdr, sizeof(sc->sc_tx_th),
733 ATH_TX_RADIOTAP_PRESENT,
734 &sc->sc_rx_th.wr_ihdr, sizeof(sc->sc_rx_th),
735 ATH_RX_RADIOTAP_PRESENT);
738 * Setup dynamic sysctl's now that country code and
739 * regdomain are available from the hal.
741 ath_sysctlattach(sc);
742 ath_sysctl_stats_attach(sc);
745 ieee80211_announce(ic);
761 ath_detach(struct ath_softc *sc)
763 struct ifnet *ifp = sc->sc_ifp;
765 DPRINTF(sc, ATH_DEBUG_ANY, "%s: if_flags %x\n",
766 __func__, ifp->if_flags);
769 * NB: the order of these is important:
770 * o stop the chip so no more interrupts will fire
771 * o call the 802.11 layer before detaching the hal to
772 * insure callbacks into the driver to delete global
773 * key cache entries can be handled
774 * o free the taskqueue which drains any pending tasks
775 * o reclaim the tx queue data structures after calling
776 * the 802.11 layer as we'll get called back to reclaim
777 * node state and potentially want to use them
778 * o to cleanup the tx queues the hal is called, so detach
780 * Other than that, it's straightforward...
783 ieee80211_ifdetach(ifp->if_l2com);
784 taskqueue_free(sc->sc_tq);
786 if (sc->sc_tx99 != NULL)
787 sc->sc_tx99->detach(sc->sc_tx99);
789 ath_rate_detach(sc->sc_rc);
792 ath_hal_detach(sc->sc_ah); /* NB: sets chip in full sleep */
793 if (sc->sc_sysctl_tree) {
794 sysctl_ctx_free(&sc->sc_sysctl_ctx);
795 sc->sc_sysctl_tree = NULL;
803 * MAC address handling for multiple BSS on the same radio.
804 * The first vap uses the MAC address from the EEPROM. For
805 * subsequent vap's we set the U/L bit (bit 1) in the MAC
806 * address and use the next six bits as an index.
809 assign_address(struct ath_softc *sc, uint8_t mac[IEEE80211_ADDR_LEN], int clone)
813 if (clone && sc->sc_hasbmask) {
814 /* NB: we only do this if h/w supports multiple bssid */
815 for (i = 0; i < 8; i++)
816 if ((sc->sc_bssidmask & (1<<i)) == 0)
819 mac[0] |= (i << 2)|0x2;
822 sc->sc_bssidmask |= 1<<i;
823 sc->sc_hwbssidmask[0] &= ~mac[0];
829 reclaim_address(struct ath_softc *sc, const uint8_t mac[IEEE80211_ADDR_LEN])
834 if (i != 0 || --sc->sc_nbssid0 == 0) {
835 sc->sc_bssidmask &= ~(1<<i);
836 /* recalculate bssid mask from remaining addresses */
838 for (i = 1; i < 8; i++)
839 if (sc->sc_bssidmask & (1<<i))
840 mask &= ~((i<<2)|0x2);
841 sc->sc_hwbssidmask[0] |= mask;
846 * Assign a beacon xmit slot. We try to space out
847 * assignments so when beacons are staggered the
848 * traffic coming out of the cab q has maximal time
849 * to go out before the next beacon is scheduled.
852 assign_bslot(struct ath_softc *sc)
857 for (slot = 0; slot < ATH_BCBUF; slot++)
858 if (sc->sc_bslot[slot] == NULL) {
859 if (sc->sc_bslot[(slot+1)%ATH_BCBUF] == NULL &&
860 sc->sc_bslot[(slot-1)%ATH_BCBUF] == NULL)
863 /* NB: keep looking for a double slot */
868 static struct ieee80211vap *
869 ath_vap_create(struct ieee80211com *ic,
870 const char name[IFNAMSIZ], int unit, int opmode, int flags,
871 const uint8_t bssid[IEEE80211_ADDR_LEN],
872 const uint8_t mac0[IEEE80211_ADDR_LEN])
874 struct ath_softc *sc = ic->ic_ifp->if_softc;
876 struct ieee80211vap *vap;
877 uint8_t mac[IEEE80211_ADDR_LEN];
878 int ic_opmode, needbeacon, error;
880 avp = (struct ath_vap *) kmalloc(sizeof(struct ath_vap),
881 M_80211_VAP, M_WAITOK | M_ZERO);
883 IEEE80211_ADDR_COPY(mac, mac0);
885 ic_opmode = opmode; /* default to opmode of new vap */
887 case IEEE80211_M_STA:
888 if (sc->sc_nstavaps != 0) { /* XXX only 1 for now */
889 device_printf(sc->sc_dev, "only 1 sta vap supported\n");
894 * With multiple vaps we must fall back
895 * to s/w beacon miss handling.
897 flags |= IEEE80211_CLONE_NOBEACONS;
899 if (flags & IEEE80211_CLONE_NOBEACONS) {
901 * Station mode w/o beacons are implemented w/ AP mode.
903 ic_opmode = IEEE80211_M_HOSTAP;
906 case IEEE80211_M_IBSS:
907 if (sc->sc_nvaps != 0) { /* XXX only 1 for now */
908 device_printf(sc->sc_dev,
909 "only 1 ibss vap supported\n");
914 case IEEE80211_M_AHDEMO:
915 #ifdef IEEE80211_SUPPORT_TDMA
916 if (flags & IEEE80211_CLONE_TDMA) {
917 if (sc->sc_nvaps != 0) {
918 device_printf(sc->sc_dev,
919 "only 1 tdma vap supported\n");
923 flags |= IEEE80211_CLONE_NOBEACONS;
927 case IEEE80211_M_MONITOR:
928 if (sc->sc_nvaps != 0 && ic->ic_opmode != opmode) {
930 * Adopt existing mode. Adding a monitor or ahdemo
931 * vap to an existing configuration is of dubious
932 * value but should be ok.
934 /* XXX not right for monitor mode */
935 ic_opmode = ic->ic_opmode;
938 case IEEE80211_M_HOSTAP:
939 case IEEE80211_M_MBSS:
942 case IEEE80211_M_WDS:
943 if (sc->sc_nvaps != 0 && ic->ic_opmode == IEEE80211_M_STA) {
944 device_printf(sc->sc_dev,
945 "wds not supported in sta mode\n");
949 * Silently remove any request for a unique
950 * bssid; WDS vap's always share the local
953 flags &= ~IEEE80211_CLONE_BSSID;
954 if (sc->sc_nvaps == 0)
955 ic_opmode = IEEE80211_M_HOSTAP;
957 ic_opmode = ic->ic_opmode;
960 device_printf(sc->sc_dev, "unknown opmode %d\n", opmode);
964 * Check that a beacon buffer is available; the code below assumes it.
966 if (needbeacon & STAILQ_EMPTY(&sc->sc_bbuf)) {
967 device_printf(sc->sc_dev, "no beacon buffer available\n");
972 if (opmode == IEEE80211_M_HOSTAP || opmode == IEEE80211_M_MBSS) {
973 assign_address(sc, mac, flags & IEEE80211_CLONE_BSSID);
974 ath_hal_setbssidmask(sc->sc_ah, sc->sc_hwbssidmask);
978 /* XXX can't hold mutex across if_alloc */
979 error = ieee80211_vap_setup(ic, vap, name, unit, opmode, flags,
982 device_printf(sc->sc_dev, "%s: error %d creating vap\n",
987 /* h/w crypto support */
988 vap->iv_key_alloc = ath_key_alloc;
989 vap->iv_key_delete = ath_key_delete;
990 vap->iv_key_set = ath_key_set;
991 vap->iv_key_update_begin = ath_key_update_begin;
992 vap->iv_key_update_end = ath_key_update_end;
994 /* override various methods */
995 avp->av_recv_mgmt = vap->iv_recv_mgmt;
996 vap->iv_recv_mgmt = ath_recv_mgmt;
997 vap->iv_reset = ath_reset_vap;
998 vap->iv_update_beacon = ath_beacon_update;
999 avp->av_newstate = vap->iv_newstate;
1000 vap->iv_newstate = ath_newstate;
1001 avp->av_bmiss = vap->iv_bmiss;
1002 vap->iv_bmiss = ath_bmiss_vap;
1007 * Allocate beacon state and setup the q for buffered
1008 * multicast frames. We know a beacon buffer is
1009 * available because we checked above.
1011 avp->av_bcbuf = STAILQ_FIRST(&sc->sc_bbuf);
1012 STAILQ_REMOVE_HEAD(&sc->sc_bbuf, bf_list);
1013 if (opmode != IEEE80211_M_IBSS || !sc->sc_hasveol) {
1015 * Assign the vap to a beacon xmit slot. As above
1016 * this cannot fail to find a free one.
1018 avp->av_bslot = assign_bslot(sc);
1019 KASSERT(sc->sc_bslot[avp->av_bslot] == NULL,
1020 ("beacon slot %u not empty", avp->av_bslot));
1021 sc->sc_bslot[avp->av_bslot] = vap;
1024 if (sc->sc_hastsfadd && sc->sc_nbcnvaps > 0) {
1026 * Multple vaps are to transmit beacons and we
1027 * have h/w support for TSF adjusting; enable
1028 * use of staggered beacons.
1030 sc->sc_stagbeacons = 1;
1032 ath_txq_init(sc, &avp->av_mcastq, ATH_TXQ_SWQ);
1035 ic->ic_opmode = ic_opmode;
1036 if (opmode != IEEE80211_M_WDS) {
1038 if (opmode == IEEE80211_M_STA)
1040 if (opmode == IEEE80211_M_MBSS)
1043 switch (ic_opmode) {
1044 case IEEE80211_M_IBSS:
1045 sc->sc_opmode = HAL_M_IBSS;
1047 case IEEE80211_M_STA:
1048 sc->sc_opmode = HAL_M_STA;
1050 case IEEE80211_M_AHDEMO:
1051 #ifdef IEEE80211_SUPPORT_TDMA
1052 if (vap->iv_caps & IEEE80211_C_TDMA) {
1054 /* NB: disable tsf adjust */
1055 sc->sc_stagbeacons = 0;
1058 * NB: adhoc demo mode is a pseudo mode; to the hal it's
1063 case IEEE80211_M_HOSTAP:
1064 case IEEE80211_M_MBSS:
1065 sc->sc_opmode = HAL_M_HOSTAP;
1067 case IEEE80211_M_MONITOR:
1068 sc->sc_opmode = HAL_M_MONITOR;
1071 /* XXX should not happen */
1074 if (sc->sc_hastsfadd) {
1076 * Configure whether or not TSF adjust should be done.
1078 ath_hal_settsfadjust(sc->sc_ah, sc->sc_stagbeacons);
1080 if (flags & IEEE80211_CLONE_NOBEACONS) {
1082 * Enable s/w beacon miss handling.
1087 /* complete setup */
1088 ieee80211_vap_attach(vap, ath_media_change, ieee80211_media_status);
1091 reclaim_address(sc, mac);
1092 ath_hal_setbssidmask(sc->sc_ah, sc->sc_hwbssidmask);
1094 kfree(avp, M_80211_VAP);
1099 ath_vap_delete(struct ieee80211vap *vap)
1101 struct ieee80211com *ic = vap->iv_ic;
1102 struct ifnet *ifp = ic->ic_ifp;
1103 struct ath_softc *sc = ifp->if_softc;
1104 struct ath_hal *ah = sc->sc_ah;
1105 struct ath_vap *avp = ATH_VAP(vap);
1107 if (ifp->if_flags & IFF_RUNNING) {
1109 * Quiesce the hardware while we remove the vap. In
1110 * particular we need to reclaim all references to
1111 * the vap state by any frames pending on the tx queues.
1113 ath_hal_intrset(ah, 0); /* disable interrupts */
1114 ath_draintxq(sc); /* stop xmit side */
1115 ath_stoprecv(sc); /* stop recv side */
1118 ieee80211_vap_detach(vap);
1120 * Reclaim beacon state. Note this must be done before
1121 * the vap instance is reclaimed as we may have a reference
1122 * to it in the buffer for the beacon frame.
1124 if (avp->av_bcbuf != NULL) {
1125 if (avp->av_bslot != -1) {
1126 sc->sc_bslot[avp->av_bslot] = NULL;
1129 ath_beacon_return(sc, avp->av_bcbuf);
1130 avp->av_bcbuf = NULL;
1131 if (sc->sc_nbcnvaps == 0) {
1132 sc->sc_stagbeacons = 0;
1133 if (sc->sc_hastsfadd)
1134 ath_hal_settsfadjust(sc->sc_ah, 0);
1137 * Reclaim any pending mcast frames for the vap.
1139 ath_tx_draintxq(sc, &avp->av_mcastq);
1142 * Update bookkeeping.
1144 if (vap->iv_opmode == IEEE80211_M_STA) {
1146 if (sc->sc_nstavaps == 0 && sc->sc_swbmiss)
1148 } else if (vap->iv_opmode == IEEE80211_M_HOSTAP ||
1149 vap->iv_opmode == IEEE80211_M_MBSS) {
1150 reclaim_address(sc, vap->iv_myaddr);
1151 ath_hal_setbssidmask(ah, sc->sc_hwbssidmask);
1152 if (vap->iv_opmode == IEEE80211_M_MBSS)
1155 if (vap->iv_opmode != IEEE80211_M_WDS)
1157 #ifdef IEEE80211_SUPPORT_TDMA
1158 /* TDMA operation ceases when the last vap is destroyed */
1159 if (sc->sc_tdma && sc->sc_nvaps == 0) {
1164 kfree(avp, M_80211_VAP);
1166 if (ifp->if_flags & IFF_RUNNING) {
1168 * Restart rx+tx machines if still running (RUNNING will
1169 * be reset if we just destroyed the last vap).
1171 if (ath_startrecv(sc) != 0)
1172 if_printf(ifp, "%s: unable to restart recv logic\n",
1174 if (sc->sc_beacons) { /* restart beacons */
1175 #ifdef IEEE80211_SUPPORT_TDMA
1177 ath_tdma_config(sc, NULL);
1180 ath_beacon_config(sc, NULL);
1182 ath_hal_intrset(ah, sc->sc_imask);
1187 ath_suspend(struct ath_softc *sc)
1189 struct ifnet *ifp = sc->sc_ifp;
1190 struct ieee80211com *ic = ifp->if_l2com;
1192 DPRINTF(sc, ATH_DEBUG_ANY, "%s: if_flags %x\n",
1193 __func__, ifp->if_flags);
1195 sc->sc_resume_up = (ifp->if_flags & IFF_UP) != 0;
1196 if (ic->ic_opmode == IEEE80211_M_STA)
1199 ieee80211_suspend_all(ic);
1201 * NB: don't worry about putting the chip in low power
1202 * mode; pci will power off our socket on suspend and
1203 * CardBus detaches the device.
1208 * Reset the key cache since some parts do not reset the
1209 * contents on resume. First we clear all entries, then
1210 * re-load keys that the 802.11 layer assumes are setup
1214 ath_reset_keycache(struct ath_softc *sc)
1216 struct ifnet *ifp = sc->sc_ifp;
1217 struct ieee80211com *ic = ifp->if_l2com;
1218 struct ath_hal *ah = sc->sc_ah;
1221 for (i = 0; i < sc->sc_keymax; i++)
1222 ath_hal_keyreset(ah, i);
1223 ieee80211_crypto_reload_keys(ic);
1227 ath_resume(struct ath_softc *sc)
1229 struct ifnet *ifp = sc->sc_ifp;
1230 struct ieee80211com *ic = ifp->if_l2com;
1231 struct ath_hal *ah = sc->sc_ah;
1234 DPRINTF(sc, ATH_DEBUG_ANY, "%s: if_flags %x\n",
1235 __func__, ifp->if_flags);
1238 * Must reset the chip before we reload the
1239 * keycache as we were powered down on suspend.
1241 ath_hal_reset(ah, sc->sc_opmode,
1242 sc->sc_curchan != NULL ? sc->sc_curchan : ic->ic_curchan,
1244 ath_reset_keycache(sc);
1245 if (sc->sc_resume_up) {
1246 if (ic->ic_opmode == IEEE80211_M_STA) {
1249 * Program the beacon registers using the last rx'd
1250 * beacon frame and enable sync on the next beacon
1251 * we see. This should handle the case where we
1252 * wakeup and find the same AP and also the case where
1253 * we wakeup and need to roam. For the latter we
1254 * should get bmiss events that trigger a roam.
1256 ath_beacon_config(sc, NULL);
1257 sc->sc_syncbeacon = 1;
1259 ieee80211_resume_all(ic);
1261 if (sc->sc_softled) {
1262 ath_hal_gpioCfgOutput(ah, sc->sc_ledpin,
1263 HAL_GPIO_MUX_MAC_NETWORK_LED);
1264 ath_hal_gpioset(ah, sc->sc_ledpin, !sc->sc_ledon);
1269 ath_shutdown(struct ath_softc *sc)
1271 struct ifnet *ifp = sc->sc_ifp;
1273 DPRINTF(sc, ATH_DEBUG_ANY, "%s: if_flags %x\n",
1274 __func__, ifp->if_flags);
1277 /* NB: no point powering down chip as we're about to reboot */
1281 * Interrupt handler. Most of the actual processing is deferred.
1286 struct ath_softc *sc = arg;
1287 struct ifnet *ifp = sc->sc_ifp;
1288 struct ath_hal *ah = sc->sc_ah;
1292 if (sc->sc_invalid) {
1294 * The hardware is not ready/present, don't touch anything.
1295 * Note this can happen early on if the IRQ is shared.
1297 DPRINTF(sc, ATH_DEBUG_ANY, "%s: invalid; ignored\n", __func__);
1301 if (!ath_hal_intrpend(ah)) /* shared irq, not for us */
1303 if ((ifp->if_flags & IFF_UP) == 0 ||
1304 (ifp->if_flags & IFF_RUNNING) == 0) {
1307 DPRINTF(sc, ATH_DEBUG_ANY, "%s: if_flags 0x%x\n",
1308 __func__, ifp->if_flags);
1309 ath_hal_getisr(ah, &status); /* clear ISR */
1310 ath_hal_intrset(ah, 0); /* disable further intr's */
1314 * Figure out the reason(s) for the interrupt. Note
1315 * that the hal returns a pseudo-ISR that may include
1316 * bits we haven't explicitly enabled so we mask the
1317 * value to insure we only process bits we requested.
1319 ath_hal_getisr(ah, &ostatus); /* NB: clears ISR too */
1320 DPRINTF(sc, ATH_DEBUG_INTR, "%s: status 0x%x\n", __func__, ostatus);
1321 status = ostatus & sc->sc_imask; /* discard unasked for bits */
1322 if (status & HAL_INT_FATAL) {
1323 sc->sc_stats.ast_hardware++;
1324 ath_hal_intrset(ah, 0); /* disable intr's until reset */
1325 ath_fatal_proc(sc, 0);
1327 if (status & HAL_INT_SWBA) {
1329 * Software beacon alert--time to send a beacon.
1330 * Handle beacon transmission directly; deferring
1331 * this is too slow to meet timing constraints
1334 #ifdef IEEE80211_SUPPORT_TDMA
1336 if (sc->sc_tdmaswba == 0) {
1337 struct ieee80211com *ic = ifp->if_l2com;
1338 struct ieee80211vap *vap =
1339 TAILQ_FIRST(&ic->ic_vaps);
1340 ath_tdma_beacon_send(sc, vap);
1342 vap->iv_tdma->tdma_bintval;
1348 ath_beacon_proc(sc, 0);
1349 #ifdef IEEE80211_SUPPORT_SUPERG
1351 * Schedule the rx taskq in case there's no
1352 * traffic so any frames held on the staging
1353 * queue are aged and potentially flushed.
1355 taskqueue_enqueue(sc->sc_tq, &sc->sc_rxtask);
1361 * NB: The hardware should re-read the link when the RXE
1362 * bit is written, but it doesn't work at least on
1365 if (status & HAL_INT_RXEOL) {
1366 sc->sc_stats.ast_rxeol++;
1367 sc->sc_rxlink = NULL;
1370 if (status & HAL_INT_TXURN) {
1371 sc->sc_stats.ast_txurn++;
1372 /* bump tx trigger level */
1373 ath_hal_updatetxtriglevel(ah, AH_TRUE);
1376 if (status & HAL_INT_RX)
1377 taskqueue_enqueue(sc->sc_tq, &sc->sc_rxtask);
1379 if (status & HAL_INT_TX)
1380 taskqueue_enqueue(sc->sc_tq, &sc->sc_txtask);
1382 if (status & HAL_INT_BMISS) {
1383 sc->sc_stats.ast_bmiss++;
1384 taskqueue_enqueue(sc->sc_tq, &sc->sc_bmisstask);
1387 if (status & HAL_INT_MIB) {
1388 sc->sc_stats.ast_mib++;
1390 * Disable interrupts until we service the MIB
1391 * interrupt; otherwise it will continue to fire.
1393 ath_hal_intrset(ah, 0);
1395 * Let the hal handle the event. We assume it will
1396 * clear whatever condition caused the interrupt.
1398 ath_hal_mibevent(ah, &sc->sc_halstats);
1399 ath_hal_intrset(ah, sc->sc_imask);
1402 if (status & HAL_INT_RXORN) {
1403 /* NB: hal marks HAL_INT_FATAL when RXORN is fatal */
1404 sc->sc_stats.ast_rxorn++;
1410 ath_fatal_proc(void *arg, int pending)
1412 struct ath_softc *sc = arg;
1413 struct ifnet *ifp = sc->sc_ifp;
1418 if_printf(ifp, "hardware error; resetting\n");
1420 * Fatal errors are unrecoverable. Typically these
1421 * are caused by DMA errors. Collect h/w state from
1422 * the hal so we can diagnose what's going on.
1424 if (ath_hal_getfatalstate(sc->sc_ah, &sp, &len)) {
1425 KASSERT(len >= 6*sizeof(u_int32_t), ("len %u bytes", len));
1427 if_printf(ifp, "0x%08x 0x%08x 0x%08x, 0x%08x 0x%08x 0x%08x\n",
1428 state[0], state[1] , state[2], state[3],
1429 state[4], state[5]);
1435 ath_bmiss_vap(struct ieee80211vap *vap)
1438 * Workaround phantom bmiss interrupts by sanity-checking
1439 * the time of our last rx'd frame. If it is within the
1440 * beacon miss interval then ignore the interrupt. If it's
1441 * truly a bmiss we'll get another interrupt soon and that'll
1442 * be dispatched up for processing. Note this applies only
1443 * for h/w beacon miss events.
1445 if ((vap->iv_flags_ext & IEEE80211_FEXT_SWBMISS) == 0) {
1446 struct ifnet *ifp = vap->iv_ic->ic_ifp;
1447 struct ath_softc *sc = ifp->if_softc;
1448 u_int64_t lastrx = sc->sc_lastrx;
1449 u_int64_t tsf = ath_hal_gettsf64(sc->sc_ah);
1450 u_int bmisstimeout =
1451 vap->iv_bmissthreshold * vap->iv_bss->ni_intval * 1024;
1453 DPRINTF(sc, ATH_DEBUG_BEACON,
1454 "%s: tsf %llu lastrx %lld (%llu) bmiss %u\n",
1455 __func__, (unsigned long long) tsf,
1456 (unsigned long long)(tsf - lastrx),
1457 (unsigned long long) lastrx, bmisstimeout);
1459 if (tsf - lastrx <= bmisstimeout) {
1460 sc->sc_stats.ast_bmiss_phantom++;
1464 ATH_VAP(vap)->av_bmiss(vap);
1468 ath_hal_gethangstate(struct ath_hal *ah, uint32_t mask, uint32_t *hangs)
1473 if (!ath_hal_getdiagstate(ah, 32, &mask, sizeof(mask), &sp, &rsize))
1475 KASSERT(rsize == sizeof(uint32_t), ("resultsize %u", rsize));
1476 *hangs = *(uint32_t *)sp;
1481 ath_bmiss_task(void *arg, int pending)
1483 struct ath_softc *sc = arg;
1484 struct ifnet *ifp = sc->sc_ifp;
1487 wlan_serialize_enter();
1488 DPRINTF(sc, ATH_DEBUG_ANY, "%s: pending %u\n", __func__, pending);
1490 if (ath_hal_gethangstate(sc->sc_ah, 0xff, &hangs) && hangs != 0) {
1491 if_printf(ifp, "bb hang detected (0x%x), reseting\n", hangs);
1494 ieee80211_beacon_miss(ifp->if_l2com);
1496 wlan_serialize_exit();
1500 * Handle TKIP MIC setup to deal hardware that doesn't do MIC
1501 * calcs together with WME. If necessary disable the crypto
1502 * hardware and mark the 802.11 state so keys will be setup
1503 * with the MIC work done in software.
1506 ath_settkipmic(struct ath_softc *sc)
1508 struct ifnet *ifp = sc->sc_ifp;
1509 struct ieee80211com *ic = ifp->if_l2com;
1511 if ((ic->ic_cryptocaps & IEEE80211_CRYPTO_TKIP) && !sc->sc_wmetkipmic) {
1512 if (ic->ic_flags & IEEE80211_F_WME) {
1513 ath_hal_settkipmic(sc->sc_ah, AH_FALSE);
1514 ic->ic_cryptocaps &= ~IEEE80211_CRYPTO_TKIPMIC;
1516 ath_hal_settkipmic(sc->sc_ah, AH_TRUE);
1517 ic->ic_cryptocaps |= IEEE80211_CRYPTO_TKIPMIC;
1525 struct ath_softc *sc = (struct ath_softc *) arg;
1526 struct ifnet *ifp = sc->sc_ifp;
1527 struct ieee80211com *ic = ifp->if_l2com;
1528 struct ath_hal *ah = sc->sc_ah;
1531 DPRINTF(sc, ATH_DEBUG_ANY, "%s: if_flags 0x%x\n",
1532 __func__, ifp->if_flags);
1535 * Stop anything previously setup. This is safe
1536 * whether this is the first time through or not.
1538 ath_stop_locked(ifp);
1541 * The basic interface to setting the hardware in a good
1542 * state is ``reset''. On return the hardware is known to
1543 * be powered up and with interrupts disabled. This must
1544 * be followed by initialization of the appropriate bits
1545 * and then setup of the interrupt mask.
1548 if (!ath_hal_reset(ah, sc->sc_opmode, ic->ic_curchan, AH_FALSE, &status)) {
1549 if_printf(ifp, "unable to reset hardware; hal status %u\n",
1553 ath_chan_change(sc, ic->ic_curchan);
1556 * Likewise this is set during reset so update
1557 * state cached in the driver.
1559 sc->sc_diversity = ath_hal_getdiversity(ah);
1560 sc->sc_lastlongcal = 0;
1561 sc->sc_resetcal = 1;
1562 sc->sc_lastcalreset = 0;
1565 * Setup the hardware after reset: the key cache
1566 * is filled as needed and the receive engine is
1567 * set going. Frame transmit is handled entirely
1568 * in the frame output path; there's nothing to do
1569 * here except setup the interrupt mask.
1571 if (ath_startrecv(sc) != 0) {
1572 if_printf(ifp, "unable to start recv logic\n");
1577 * Enable interrupts.
1579 sc->sc_imask = HAL_INT_RX | HAL_INT_TX
1580 | HAL_INT_RXEOL | HAL_INT_RXORN
1581 | HAL_INT_FATAL | HAL_INT_GLOBAL;
1583 * Enable MIB interrupts when there are hardware phy counters.
1584 * Note we only do this (at the moment) for station mode.
1586 if (sc->sc_needmib && ic->ic_opmode == IEEE80211_M_STA)
1587 sc->sc_imask |= HAL_INT_MIB;
1589 ifp->if_flags |= IFF_RUNNING;
1590 callout_reset(&sc->sc_wd_ch, hz, ath_watchdog_callout, sc);
1591 ath_hal_intrset(ah, sc->sc_imask);
1594 #ifdef ATH_TX99_DIAG
1595 if (sc->sc_tx99 != NULL)
1596 sc->sc_tx99->start(sc->sc_tx99);
1599 ieee80211_start_all(ic); /* start all vap's */
1603 ath_stop_locked(struct ifnet *ifp)
1605 struct ath_softc *sc = ifp->if_softc;
1606 struct ath_hal *ah = sc->sc_ah;
1608 DPRINTF(sc, ATH_DEBUG_ANY, "%s: invalid %u if_flags 0x%x\n",
1609 __func__, sc->sc_invalid, ifp->if_flags);
1611 if (ifp->if_flags & IFF_RUNNING) {
1613 * Shutdown the hardware and driver:
1614 * reset 802.11 state machine
1616 * disable interrupts
1617 * turn off the radio
1618 * clear transmit machinery
1619 * clear receive machinery
1620 * drain and release tx queues
1621 * reclaim beacon resources
1622 * power down hardware
1624 * Note that some of this work is not possible if the
1625 * hardware is gone (invalid).
1627 #ifdef ATH_TX99_DIAG
1628 if (sc->sc_tx99 != NULL)
1629 sc->sc_tx99->stop(sc->sc_tx99);
1631 callout_stop(&sc->sc_wd_ch);
1632 sc->sc_wd_timer = 0;
1633 ifp->if_flags &= ~IFF_RUNNING;
1634 if (!sc->sc_invalid) {
1635 if (sc->sc_softled) {
1636 callout_stop(&sc->sc_ledtimer);
1637 ath_hal_gpioset(ah, sc->sc_ledpin,
1639 sc->sc_blinking = 0;
1641 ath_hal_intrset(ah, 0);
1644 if (!sc->sc_invalid) {
1646 ath_hal_phydisable(ah);
1648 sc->sc_rxlink = NULL;
1649 ath_beacon_free(sc); /* XXX not needed */
1654 ath_stop(struct ifnet *ifp)
1656 struct ath_softc *sc __unused = ifp->if_softc;
1658 ath_stop_locked(ifp);
1662 * Reset the hardware w/o losing operational state. This is
1663 * basically a more efficient way of doing ath_stop, ath_init,
1664 * followed by state transitions to the current 802.11
1665 * operational state. Used to recover from various errors and
1666 * to reset or reload hardware state.
1669 ath_reset(struct ifnet *ifp)
1671 struct ath_softc *sc = ifp->if_softc;
1672 struct ieee80211com *ic = ifp->if_l2com;
1673 struct ath_hal *ah = sc->sc_ah;
1676 ath_hal_intrset(ah, 0); /* disable interrupts */
1677 ath_draintxq(sc); /* stop xmit side */
1678 ath_stoprecv(sc); /* stop recv side */
1679 ath_settkipmic(sc); /* configure TKIP MIC handling */
1680 /* NB: indicate channel change so we do a full reset */
1681 if (!ath_hal_reset(ah, sc->sc_opmode, ic->ic_curchan, AH_TRUE, &status))
1682 if_printf(ifp, "%s: unable to reset hardware; hal status %u\n",
1684 sc->sc_diversity = ath_hal_getdiversity(ah);
1685 if (ath_startrecv(sc) != 0) /* restart recv */
1686 if_printf(ifp, "%s: unable to start recv logic\n", __func__);
1688 * We may be doing a reset in response to an ioctl
1689 * that changes the channel so update any state that
1690 * might change as a result.
1692 ath_chan_change(sc, ic->ic_curchan);
1693 if (sc->sc_beacons) { /* restart beacons */
1694 #ifdef IEEE80211_SUPPORT_TDMA
1696 ath_tdma_config(sc, NULL);
1699 ath_beacon_config(sc, NULL);
1701 ath_hal_intrset(ah, sc->sc_imask);
1703 ath_start(ifp); /* restart xmit */
1708 ath_reset_vap(struct ieee80211vap *vap, u_long cmd)
1710 struct ieee80211com *ic = vap->iv_ic;
1711 struct ifnet *ifp = ic->ic_ifp;
1712 struct ath_softc *sc = ifp->if_softc;
1713 struct ath_hal *ah = sc->sc_ah;
1716 case IEEE80211_IOC_TXPOWER:
1718 * If per-packet TPC is enabled, then we have nothing
1719 * to do; otherwise we need to force the global limit.
1720 * All this can happen directly; no need to reset.
1722 if (!ath_hal_gettpc(ah))
1723 ath_hal_settxpowlimit(ah, ic->ic_txpowlimit);
1726 return ath_reset(ifp);
1729 static struct ath_buf *
1730 _ath_getbuf_locked(struct ath_softc *sc)
1734 bf = STAILQ_FIRST(&sc->sc_txbuf);
1735 if (bf != NULL && (bf->bf_flags & ATH_BUF_BUSY) == 0)
1736 STAILQ_REMOVE_HEAD(&sc->sc_txbuf, bf_list);
1740 kprintf("ath: ran out of descriptors\n");
1741 DPRINTF(sc, ATH_DEBUG_XMIT, "%s: %s\n", __func__,
1742 STAILQ_FIRST(&sc->sc_txbuf) == NULL ?
1743 "out of xmit buffers" : "xmit buffer busy");
1748 static struct ath_buf *
1749 ath_getbuf(struct ath_softc *sc)
1753 bf = _ath_getbuf_locked(sc);
1755 struct ifnet *ifp = sc->sc_ifp;
1757 DPRINTF(sc, ATH_DEBUG_XMIT, "%s: stop queue\n", __func__);
1758 sc->sc_stats.ast_tx_qstop++;
1759 ifp->if_flags |= IFF_OACTIVE;
1765 * Cleanup driver resources when we run out of buffers
1766 * while processing fragments; return the tx buffers
1767 * allocated and drop node references.
1770 ath_txfrag_cleanup(struct ath_softc *sc,
1771 ath_bufhead *frags, struct ieee80211_node *ni)
1773 struct ath_buf *bf, *next;
1775 STAILQ_FOREACH_MUTABLE(bf, frags, bf_list, next) {
1776 /* NB: bf assumed clean */
1777 STAILQ_REMOVE_HEAD(frags, bf_list);
1778 STAILQ_INSERT_HEAD(&sc->sc_txbuf, bf, bf_list);
1779 ieee80211_node_decref(ni);
1784 * Setup xmit of a fragmented frame. Allocate a buffer
1785 * for each frag and bump the node reference count to
1786 * reflect the held reference to be setup by ath_tx_start.
1789 ath_txfrag_setup(struct ath_softc *sc, ath_bufhead *frags,
1790 struct mbuf *m0, struct ieee80211_node *ni)
1795 for (m = m0->m_nextpkt; m != NULL; m = m->m_nextpkt) {
1796 bf = _ath_getbuf_locked(sc);
1797 if (bf == NULL) { /* out of buffers, cleanup */
1798 ath_txfrag_cleanup(sc, frags, ni);
1801 ieee80211_node_incref(ni);
1802 STAILQ_INSERT_TAIL(frags, bf, bf_list);
1805 return !STAILQ_EMPTY(frags);
1809 ath_start(struct ifnet *ifp)
1811 struct ath_softc *sc = ifp->if_softc;
1812 struct ieee80211_node *ni;
1814 struct mbuf *m, *next;
1817 if ((ifp->if_flags & IFF_RUNNING) == 0 || sc->sc_invalid) {
1818 ifq_purge(&ifp->if_snd);
1823 * Grab a TX buffer and associated resources.
1825 bf = ath_getbuf(sc);
1829 IF_DEQUEUE(&ifp->if_snd, m);
1831 STAILQ_INSERT_HEAD(&sc->sc_txbuf, bf, bf_list);
1834 ni = (struct ieee80211_node *) m->m_pkthdr.rcvif;
1836 * Check for fragmentation. If this frame
1837 * has been broken up verify we have enough
1838 * buffers to send all the fragments so all
1841 STAILQ_INIT(&frags);
1842 if ((m->m_flags & M_FRAG) &&
1843 !ath_txfrag_setup(sc, &frags, m, ni)) {
1844 DPRINTF(sc, ATH_DEBUG_XMIT,
1845 "%s: out of txfrag buffers\n", __func__);
1846 sc->sc_stats.ast_tx_nofrag++;
1854 * Pass the frame to the h/w for transmission.
1855 * Fragmented frames have each frag chained together
1856 * with m_nextpkt. We know there are sufficient ath_buf's
1857 * to send all the frags because of work done by
1858 * ath_txfrag_setup. We leave m_nextpkt set while
1859 * calling ath_tx_start so it can use it to extend the
1860 * the tx duration to cover the subsequent frag and
1861 * so it can reclaim all the mbufs in case of an error;
1862 * ath_tx_start clears m_nextpkt once it commits to
1863 * handing the frame to the hardware.
1865 next = m->m_nextpkt;
1866 if (ath_tx_start(sc, ni, bf, m)) {
1872 STAILQ_INSERT_HEAD(&sc->sc_txbuf, bf, bf_list);
1873 ath_txfrag_cleanup(sc, &frags, ni);
1875 ieee80211_free_node(ni);
1880 * Beware of state changing between frags.
1881 * XXX check sta power-save state?
1883 if (ni->ni_vap->iv_state != IEEE80211_S_RUN) {
1884 DPRINTF(sc, ATH_DEBUG_XMIT,
1885 "%s: flush fragmented packet, state %s\n",
1887 ieee80211_state_name[ni->ni_vap->iv_state]);
1892 bf = STAILQ_FIRST(&frags);
1893 KASSERT(bf != NULL, ("no buf for txfrag"));
1894 STAILQ_REMOVE_HEAD(&frags, bf_list);
1898 sc->sc_wd_timer = 5;
1903 ath_media_change(struct ifnet *ifp)
1905 int error = ieee80211_media_change(ifp);
1906 /* NB: only the fixed rate can change and that doesn't need a reset */
1907 return (error == ENETRESET ? 0 : error);
1912 ath_keyprint(struct ath_softc *sc, const char *tag, u_int ix,
1913 const HAL_KEYVAL *hk, const u_int8_t mac[IEEE80211_ADDR_LEN])
1915 static const char *ciphers[] = {
1925 kprintf("%s: [%02u] %-7s ", tag, ix, ciphers[hk->kv_type]);
1926 for (i = 0, n = hk->kv_len; i < n; i++)
1927 kprintf("%02x", hk->kv_val[i]);
1928 kprintf(" mac %6D", mac, ":");
1929 if (hk->kv_type == HAL_CIPHER_TKIP) {
1930 kprintf(" %s ", sc->sc_splitmic ? "mic" : "rxmic");
1931 for (i = 0; i < sizeof(hk->kv_mic); i++)
1932 kprintf("%02x", hk->kv_mic[i]);
1933 if (!sc->sc_splitmic) {
1935 for (i = 0; i < sizeof(hk->kv_txmic); i++)
1936 kprintf("%02x", hk->kv_txmic[i]);
1944 * Set a TKIP key into the hardware. This handles the
1945 * potential distribution of key state to multiple key
1946 * cache slots for TKIP.
1949 ath_keyset_tkip(struct ath_softc *sc, const struct ieee80211_key *k,
1950 HAL_KEYVAL *hk, const u_int8_t mac[IEEE80211_ADDR_LEN])
1952 #define IEEE80211_KEY_XR (IEEE80211_KEY_XMIT | IEEE80211_KEY_RECV)
1953 static const u_int8_t zerobssid[IEEE80211_ADDR_LEN];
1954 struct ath_hal *ah = sc->sc_ah;
1956 KASSERT(k->wk_cipher->ic_cipher == IEEE80211_CIPHER_TKIP,
1957 ("got a non-TKIP key, cipher %u", k->wk_cipher->ic_cipher));
1958 if ((k->wk_flags & IEEE80211_KEY_XR) == IEEE80211_KEY_XR) {
1959 if (sc->sc_splitmic) {
1961 * TX key goes at first index, RX key at the rx index.
1962 * The hal handles the MIC keys at index+64.
1964 memcpy(hk->kv_mic, k->wk_txmic, sizeof(hk->kv_mic));
1965 KEYPRINTF(sc, k->wk_keyix, hk, zerobssid);
1966 if (!ath_hal_keyset(ah, k->wk_keyix, hk, zerobssid))
1969 memcpy(hk->kv_mic, k->wk_rxmic, sizeof(hk->kv_mic));
1970 KEYPRINTF(sc, k->wk_keyix+32, hk, mac);
1971 /* XXX delete tx key on failure? */
1972 return ath_hal_keyset(ah, k->wk_keyix+32, hk, mac);
1975 * Room for both TX+RX MIC keys in one key cache
1976 * slot, just set key at the first index; the hal
1977 * will handle the rest.
1979 memcpy(hk->kv_mic, k->wk_rxmic, sizeof(hk->kv_mic));
1980 memcpy(hk->kv_txmic, k->wk_txmic, sizeof(hk->kv_txmic));
1981 KEYPRINTF(sc, k->wk_keyix, hk, mac);
1982 return ath_hal_keyset(ah, k->wk_keyix, hk, mac);
1984 } else if (k->wk_flags & IEEE80211_KEY_XMIT) {
1985 if (sc->sc_splitmic) {
1987 * NB: must pass MIC key in expected location when
1988 * the keycache only holds one MIC key per entry.
1990 memcpy(hk->kv_mic, k->wk_txmic, sizeof(hk->kv_txmic));
1992 memcpy(hk->kv_txmic, k->wk_txmic, sizeof(hk->kv_txmic));
1993 KEYPRINTF(sc, k->wk_keyix, hk, mac);
1994 return ath_hal_keyset(ah, k->wk_keyix, hk, mac);
1995 } else if (k->wk_flags & IEEE80211_KEY_RECV) {
1996 memcpy(hk->kv_mic, k->wk_rxmic, sizeof(hk->kv_mic));
1997 KEYPRINTF(sc, k->wk_keyix, hk, mac);
1998 return ath_hal_keyset(ah, k->wk_keyix, hk, mac);
2001 #undef IEEE80211_KEY_XR
2005 * Set a net80211 key into the hardware. This handles the
2006 * potential distribution of key state to multiple key
2007 * cache slots for TKIP with hardware MIC support.
2010 ath_keyset(struct ath_softc *sc, const struct ieee80211_key *k,
2011 struct ieee80211_node *bss)
2013 static const u_int8_t ciphermap[] = {
2014 HAL_CIPHER_WEP, /* IEEE80211_CIPHER_WEP */
2015 HAL_CIPHER_TKIP, /* IEEE80211_CIPHER_TKIP */
2016 HAL_CIPHER_AES_OCB, /* IEEE80211_CIPHER_AES_OCB */
2017 HAL_CIPHER_AES_CCM, /* IEEE80211_CIPHER_AES_CCM */
2018 (u_int8_t) -1, /* 4 is not allocated */
2019 HAL_CIPHER_CKIP, /* IEEE80211_CIPHER_CKIP */
2020 HAL_CIPHER_CLR, /* IEEE80211_CIPHER_NONE */
2022 struct ath_hal *ah = sc->sc_ah;
2023 const struct ieee80211_cipher *cip = k->wk_cipher;
2024 u_int8_t gmac[IEEE80211_ADDR_LEN];
2025 const u_int8_t *mac;
2028 memset(&hk, 0, sizeof(hk));
2030 * Software crypto uses a "clear key" so non-crypto
2031 * state kept in the key cache are maintained and
2032 * so that rx frames have an entry to match.
2034 if ((k->wk_flags & IEEE80211_KEY_SWCRYPT) == 0) {
2035 KASSERT(cip->ic_cipher < NELEM(ciphermap),
2036 ("invalid cipher type %u", cip->ic_cipher));
2037 hk.kv_type = ciphermap[cip->ic_cipher];
2038 hk.kv_len = k->wk_keylen;
2039 memcpy(hk.kv_val, k->wk_key, k->wk_keylen);
2041 hk.kv_type = HAL_CIPHER_CLR;
2043 if ((k->wk_flags & IEEE80211_KEY_GROUP) && sc->sc_mcastkey) {
2045 * Group keys on hardware that supports multicast frame
2046 * key search use a MAC that is the sender's address with
2047 * the high bit set instead of the app-specified address.
2049 IEEE80211_ADDR_COPY(gmac, bss->ni_macaddr);
2053 mac = k->wk_macaddr;
2055 if (hk.kv_type == HAL_CIPHER_TKIP &&
2056 (k->wk_flags & IEEE80211_KEY_SWMIC) == 0) {
2057 return ath_keyset_tkip(sc, k, &hk, mac);
2059 KEYPRINTF(sc, k->wk_keyix, &hk, mac);
2060 return ath_hal_keyset(ah, k->wk_keyix, &hk, mac);
2065 * Allocate tx/rx key slots for TKIP. We allocate two slots for
2066 * each key, one for decrypt/encrypt and the other for the MIC.
2069 key_alloc_2pair(struct ath_softc *sc,
2070 ieee80211_keyix *txkeyix, ieee80211_keyix *rxkeyix)
2074 KASSERT(sc->sc_splitmic, ("key cache !split"));
2075 /* XXX could optimize */
2076 for (i = 0; i < NELEM(sc->sc_keymap)/4; i++) {
2077 u_int8_t b = sc->sc_keymap[i];
2080 * One or more slots in this byte are free.
2088 /* XXX IEEE80211_KEY_XMIT | IEEE80211_KEY_RECV */
2089 if (isset(sc->sc_keymap, keyix+32) ||
2090 isset(sc->sc_keymap, keyix+64) ||
2091 isset(sc->sc_keymap, keyix+32+64)) {
2092 /* full pair unavailable */
2094 if (keyix == (i+1)*NBBY) {
2095 /* no slots were appropriate, advance */
2100 setbit(sc->sc_keymap, keyix);
2101 setbit(sc->sc_keymap, keyix+64);
2102 setbit(sc->sc_keymap, keyix+32);
2103 setbit(sc->sc_keymap, keyix+32+64);
2104 DPRINTF(sc, ATH_DEBUG_KEYCACHE,
2105 "%s: key pair %u,%u %u,%u\n",
2106 __func__, keyix, keyix+64,
2107 keyix+32, keyix+32+64);
2109 *rxkeyix = keyix+32;
2113 DPRINTF(sc, ATH_DEBUG_KEYCACHE, "%s: out of pair space\n", __func__);
2118 * Allocate tx/rx key slots for TKIP. We allocate two slots for
2119 * each key, one for decrypt/encrypt and the other for the MIC.
2122 key_alloc_pair(struct ath_softc *sc,
2123 ieee80211_keyix *txkeyix, ieee80211_keyix *rxkeyix)
2127 KASSERT(!sc->sc_splitmic, ("key cache split"));
2128 /* XXX could optimize */
2129 for (i = 0; i < NELEM(sc->sc_keymap)/4; i++) {
2130 u_int8_t b = sc->sc_keymap[i];
2133 * One or more slots in this byte are free.
2141 if (isset(sc->sc_keymap, keyix+64)) {
2142 /* full pair unavailable */
2144 if (keyix == (i+1)*NBBY) {
2145 /* no slots were appropriate, advance */
2150 setbit(sc->sc_keymap, keyix);
2151 setbit(sc->sc_keymap, keyix+64);
2152 DPRINTF(sc, ATH_DEBUG_KEYCACHE,
2153 "%s: key pair %u,%u\n",
2154 __func__, keyix, keyix+64);
2155 *txkeyix = *rxkeyix = keyix;
2159 DPRINTF(sc, ATH_DEBUG_KEYCACHE, "%s: out of pair space\n", __func__);
2164 * Allocate a single key cache slot.
2167 key_alloc_single(struct ath_softc *sc,
2168 ieee80211_keyix *txkeyix, ieee80211_keyix *rxkeyix)
2172 /* XXX try i,i+32,i+64,i+32+64 to minimize key pair conflicts */
2173 for (i = 0; i < NELEM(sc->sc_keymap); i++) {
2174 u_int8_t b = sc->sc_keymap[i];
2177 * One or more slots are free.
2182 setbit(sc->sc_keymap, keyix);
2183 DPRINTF(sc, ATH_DEBUG_KEYCACHE, "%s: key %u\n",
2185 *txkeyix = *rxkeyix = keyix;
2189 DPRINTF(sc, ATH_DEBUG_KEYCACHE, "%s: out of space\n", __func__);
2194 * Allocate one or more key cache slots for a uniacst key. The
2195 * key itself is needed only to identify the cipher. For hardware
2196 * TKIP with split cipher+MIC keys we allocate two key cache slot
2197 * pairs so that we can setup separate TX and RX MIC keys. Note
2198 * that the MIC key for a TKIP key at slot i is assumed by the
2199 * hardware to be at slot i+64. This limits TKIP keys to the first
2203 ath_key_alloc(struct ieee80211vap *vap, struct ieee80211_key *k,
2204 ieee80211_keyix *keyix, ieee80211_keyix *rxkeyix)
2206 struct ath_softc *sc = vap->iv_ic->ic_ifp->if_softc;
2209 * Group key allocation must be handled specially for
2210 * parts that do not support multicast key cache search
2211 * functionality. For those parts the key id must match
2212 * the h/w key index so lookups find the right key. On
2213 * parts w/ the key search facility we install the sender's
2214 * mac address (with the high bit set) and let the hardware
2215 * find the key w/o using the key id. This is preferred as
2216 * it permits us to support multiple users for adhoc and/or
2217 * multi-station operation.
2219 if (k->wk_keyix != IEEE80211_KEYIX_NONE) {
2221 * Only global keys should have key index assigned.
2223 if (!(&vap->iv_nw_keys[0] <= k &&
2224 k < &vap->iv_nw_keys[IEEE80211_WEP_NKID])) {
2225 /* should not happen */
2226 DPRINTF(sc, ATH_DEBUG_KEYCACHE,
2227 "%s: bogus group key\n", __func__);
2230 if (vap->iv_opmode != IEEE80211_M_HOSTAP ||
2231 !(k->wk_flags & IEEE80211_KEY_GROUP) ||
2234 * XXX we pre-allocate the global keys so
2235 * have no way to check if they've already
2238 *keyix = *rxkeyix = k - vap->iv_nw_keys;
2242 * Group key and device supports multicast key search.
2244 k->wk_keyix = IEEE80211_KEYIX_NONE;
2248 * We allocate two pair for TKIP when using the h/w to do
2249 * the MIC. For everything else, including software crypto,
2250 * we allocate a single entry. Note that s/w crypto requires
2251 * a pass-through slot on the 5211 and 5212. The 5210 does
2252 * not support pass-through cache entries and we map all
2253 * those requests to slot 0.
2255 if (k->wk_flags & IEEE80211_KEY_SWCRYPT) {
2256 return key_alloc_single(sc, keyix, rxkeyix);
2257 } else if (k->wk_cipher->ic_cipher == IEEE80211_CIPHER_TKIP &&
2258 (k->wk_flags & IEEE80211_KEY_SWMIC) == 0) {
2259 if (sc->sc_splitmic)
2260 return key_alloc_2pair(sc, keyix, rxkeyix);
2262 return key_alloc_pair(sc, keyix, rxkeyix);
2264 return key_alloc_single(sc, keyix, rxkeyix);
2269 * Delete an entry in the key cache allocated by ath_key_alloc.
2272 ath_key_delete(struct ieee80211vap *vap, const struct ieee80211_key *k)
2274 struct ath_softc *sc = vap->iv_ic->ic_ifp->if_softc;
2275 struct ath_hal *ah = sc->sc_ah;
2276 const struct ieee80211_cipher *cip = k->wk_cipher;
2277 u_int keyix = k->wk_keyix;
2279 DPRINTF(sc, ATH_DEBUG_KEYCACHE, "%s: delete key %u\n", __func__, keyix);
2281 ath_hal_keyreset(ah, keyix);
2283 * Handle split tx/rx keying required for TKIP with h/w MIC.
2285 if (cip->ic_cipher == IEEE80211_CIPHER_TKIP &&
2286 (k->wk_flags & IEEE80211_KEY_SWMIC) == 0 && sc->sc_splitmic)
2287 ath_hal_keyreset(ah, keyix+32); /* RX key */
2288 if (keyix >= IEEE80211_WEP_NKID) {
2290 * Don't touch keymap entries for global keys so
2291 * they are never considered for dynamic allocation.
2293 clrbit(sc->sc_keymap, keyix);
2294 if (cip->ic_cipher == IEEE80211_CIPHER_TKIP &&
2295 (k->wk_flags & IEEE80211_KEY_SWMIC) == 0) {
2296 clrbit(sc->sc_keymap, keyix+64); /* TX key MIC */
2297 if (sc->sc_splitmic) {
2298 /* +32 for RX key, +32+64 for RX key MIC */
2299 clrbit(sc->sc_keymap, keyix+32);
2300 clrbit(sc->sc_keymap, keyix+32+64);
2308 * Set the key cache contents for the specified key. Key cache
2309 * slot(s) must already have been allocated by ath_key_alloc.
2312 ath_key_set(struct ieee80211vap *vap, const struct ieee80211_key *k,
2313 const u_int8_t mac[IEEE80211_ADDR_LEN])
2315 struct ath_softc *sc = vap->iv_ic->ic_ifp->if_softc;
2317 return ath_keyset(sc, k, vap->iv_bss);
2321 * Block/unblock tx+rx processing while a key change is done.
2322 * We assume the caller serializes key management operations
2323 * so we only need to worry about synchronization with other
2324 * uses that originate in the driver.
2327 ath_key_update_begin(struct ieee80211vap *vap)
2329 struct ifnet *ifp = vap->iv_ic->ic_ifp;
2330 struct ath_softc *sc = ifp->if_softc;
2332 DPRINTF(sc, ATH_DEBUG_KEYCACHE, "%s:\n", __func__);
2333 taskqueue_block(sc->sc_tq);
2337 ath_key_update_end(struct ieee80211vap *vap)
2339 struct ifnet *ifp = vap->iv_ic->ic_ifp;
2340 struct ath_softc *sc = ifp->if_softc;
2342 DPRINTF(sc, ATH_DEBUG_KEYCACHE, "%s:\n", __func__);
2343 taskqueue_unblock(sc->sc_tq);
2347 * Calculate the receive filter according to the
2348 * operating mode and state:
2350 * o always accept unicast, broadcast, and multicast traffic
2351 * o accept PHY error frames when hardware doesn't have MIB support
2352 * to count and we need them for ANI (sta mode only until recently)
2353 * and we are not scanning (ANI is disabled)
2354 * NB: older hal's add rx filter bits out of sight and we need to
2355 * blindly preserve them
2356 * o probe request frames are accepted only when operating in
2357 * hostap, adhoc, mesh, or monitor modes
2358 * o enable promiscuous mode
2359 * - when in monitor mode
2360 * - if interface marked PROMISC (assumes bridge setting is filtered)
2362 * - when operating in station mode for collecting rssi data when
2363 * the station is otherwise quiet, or
2364 * - when operating in adhoc mode so the 802.11 layer creates
2365 * node table entries for peers,
2367 * - when doing s/w beacon miss (e.g. for ap+sta)
2368 * - when operating in ap mode in 11g to detect overlapping bss that
2369 * require protection
2370 * - when operating in mesh mode to detect neighbors
2371 * o accept control frames:
2372 * - when in monitor mode
2373 * XXX BAR frames for 11n
2374 * XXX HT protection for 11n
2377 ath_calcrxfilter(struct ath_softc *sc)
2379 struct ifnet *ifp = sc->sc_ifp;
2380 struct ieee80211com *ic = ifp->if_l2com;
2383 rfilt = HAL_RX_FILTER_UCAST | HAL_RX_FILTER_BCAST | HAL_RX_FILTER_MCAST;
2384 if (!sc->sc_needmib && !sc->sc_scanning)
2385 rfilt |= HAL_RX_FILTER_PHYERR;
2386 if (ic->ic_opmode != IEEE80211_M_STA)
2387 rfilt |= HAL_RX_FILTER_PROBEREQ;
2388 /* XXX ic->ic_monvaps != 0? */
2389 if (ic->ic_opmode == IEEE80211_M_MONITOR || (ifp->if_flags & IFF_PROMISC))
2390 rfilt |= HAL_RX_FILTER_PROM;
2391 if (ic->ic_opmode == IEEE80211_M_STA ||
2392 ic->ic_opmode == IEEE80211_M_IBSS ||
2393 sc->sc_swbmiss || sc->sc_scanning)
2394 rfilt |= HAL_RX_FILTER_BEACON;
2396 * NB: We don't recalculate the rx filter when
2397 * ic_protmode changes; otherwise we could do
2398 * this only when ic_protmode != NONE.
2400 if (ic->ic_opmode == IEEE80211_M_HOSTAP &&
2401 IEEE80211_IS_CHAN_ANYG(ic->ic_curchan))
2402 rfilt |= HAL_RX_FILTER_BEACON;
2403 if (sc->sc_nmeshvaps) {
2404 rfilt |= HAL_RX_FILTER_BEACON;
2405 if (sc->sc_hasbmatch)
2406 rfilt |= HAL_RX_FILTER_BSSID;
2408 rfilt |= HAL_RX_FILTER_PROM;
2410 if (ic->ic_opmode == IEEE80211_M_MONITOR)
2411 rfilt |= HAL_RX_FILTER_CONTROL;
2412 DPRINTF(sc, ATH_DEBUG_MODE, "%s: RX filter 0x%x, %s if_flags 0x%x\n",
2413 __func__, rfilt, ieee80211_opmode_name[ic->ic_opmode], ifp->if_flags);
2418 ath_update_promisc(struct ifnet *ifp)
2420 struct ath_softc *sc = ifp->if_softc;
2423 /* configure rx filter */
2424 rfilt = ath_calcrxfilter(sc);
2425 ath_hal_setrxfilter(sc->sc_ah, rfilt);
2427 DPRINTF(sc, ATH_DEBUG_MODE, "%s: RX filter 0x%x\n", __func__, rfilt);
2431 ath_update_mcast(struct ifnet *ifp)
2433 struct ath_softc *sc = ifp->if_softc;
2436 /* calculate and install multicast filter */
2437 if ((ifp->if_flags & IFF_ALLMULTI) == 0) {
2438 struct ifmultiaddr *ifma;
2440 * Merge multicast addresses to form the hardware filter.
2442 mfilt[0] = mfilt[1] = 0;
2444 if_maddr_rlock(ifp); /* XXX need some fiddling to remove? */
2446 TAILQ_FOREACH(ifma, &ifp->if_multiaddrs, ifma_link) {
2451 /* calculate XOR of eight 6bit values */
2452 dl = LLADDR((struct sockaddr_dl *) ifma->ifma_addr);
2453 val = LE_READ_4(dl + 0);
2454 pos = (val >> 18) ^ (val >> 12) ^ (val >> 6) ^ val;
2455 val = LE_READ_4(dl + 3);
2456 pos ^= (val >> 18) ^ (val >> 12) ^ (val >> 6) ^ val;
2458 mfilt[pos / 32] |= (1 << (pos % 32));
2461 if_maddr_runlock(ifp);
2464 mfilt[0] = mfilt[1] = ~0;
2465 ath_hal_setmcastfilter(sc->sc_ah, mfilt[0], mfilt[1]);
2466 DPRINTF(sc, ATH_DEBUG_MODE, "%s: MC filter %08x:%08x\n",
2467 __func__, mfilt[0], mfilt[1]);
2471 ath_mode_init(struct ath_softc *sc)
2473 struct ifnet *ifp = sc->sc_ifp;
2474 struct ath_hal *ah = sc->sc_ah;
2477 /* configure rx filter */
2478 rfilt = ath_calcrxfilter(sc);
2479 ath_hal_setrxfilter(ah, rfilt);
2481 /* configure operational mode */
2482 ath_hal_setopmode(ah);
2484 /* handle any link-level address change */
2485 ath_hal_setmac(ah, IF_LLADDR(ifp));
2487 /* calculate and install multicast filter */
2488 ath_update_mcast(ifp);
2492 * Set the slot time based on the current setting.
2495 ath_setslottime(struct ath_softc *sc)
2497 struct ieee80211com *ic = sc->sc_ifp->if_l2com;
2498 struct ath_hal *ah = sc->sc_ah;
2501 if (IEEE80211_IS_CHAN_HALF(ic->ic_curchan))
2503 else if (IEEE80211_IS_CHAN_QUARTER(ic->ic_curchan))
2505 else if (IEEE80211_IS_CHAN_ANYG(ic->ic_curchan)) {
2506 /* honor short/long slot time only in 11g */
2507 /* XXX shouldn't honor on pure g or turbo g channel */
2508 if (ic->ic_flags & IEEE80211_F_SHSLOT)
2509 usec = HAL_SLOT_TIME_9;
2511 usec = HAL_SLOT_TIME_20;
2513 usec = HAL_SLOT_TIME_9;
2515 DPRINTF(sc, ATH_DEBUG_RESET,
2516 "%s: chan %u MHz flags 0x%x %s slot, %u usec\n",
2517 __func__, ic->ic_curchan->ic_freq, ic->ic_curchan->ic_flags,
2518 ic->ic_flags & IEEE80211_F_SHSLOT ? "short" : "long", usec);
2520 ath_hal_setslottime(ah, usec);
2521 sc->sc_updateslot = OK;
2525 * Callback from the 802.11 layer to update the
2526 * slot time based on the current setting.
2529 ath_updateslot(struct ifnet *ifp)
2531 struct ath_softc *sc = ifp->if_softc;
2532 struct ieee80211com *ic = ifp->if_l2com;
2535 * When not coordinating the BSS, change the hardware
2536 * immediately. For other operation we defer the change
2537 * until beacon updates have propagated to the stations.
2539 if (ic->ic_opmode == IEEE80211_M_HOSTAP ||
2540 ic->ic_opmode == IEEE80211_M_MBSS)
2541 sc->sc_updateslot = UPDATE;
2543 ath_setslottime(sc);
2547 * Setup a h/w transmit queue for beacons.
2550 ath_beaconq_setup(struct ath_hal *ah)
2554 memset(&qi, 0, sizeof(qi));
2555 qi.tqi_aifs = HAL_TXQ_USEDEFAULT;
2556 qi.tqi_cwmin = HAL_TXQ_USEDEFAULT;
2557 qi.tqi_cwmax = HAL_TXQ_USEDEFAULT;
2558 /* NB: for dynamic turbo, don't enable any other interrupts */
2559 qi.tqi_qflags = HAL_TXQ_TXDESCINT_ENABLE;
2560 return ath_hal_setuptxqueue(ah, HAL_TX_QUEUE_BEACON, &qi);
2564 * Setup the transmit queue parameters for the beacon queue.
2567 ath_beaconq_config(struct ath_softc *sc)
2569 #define ATH_EXPONENT_TO_VALUE(v) ((1<<(v))-1)
2570 struct ieee80211com *ic = sc->sc_ifp->if_l2com;
2571 struct ath_hal *ah = sc->sc_ah;
2574 ath_hal_gettxqueueprops(ah, sc->sc_bhalq, &qi);
2575 if (ic->ic_opmode == IEEE80211_M_HOSTAP ||
2576 ic->ic_opmode == IEEE80211_M_MBSS) {
2578 * Always burst out beacon and CAB traffic.
2580 qi.tqi_aifs = ATH_BEACON_AIFS_DEFAULT;
2581 qi.tqi_cwmin = ATH_BEACON_CWMIN_DEFAULT;
2582 qi.tqi_cwmax = ATH_BEACON_CWMAX_DEFAULT;
2584 struct wmeParams *wmep =
2585 &ic->ic_wme.wme_chanParams.cap_wmeParams[WME_AC_BE];
2587 * Adhoc mode; important thing is to use 2x cwmin.
2589 qi.tqi_aifs = wmep->wmep_aifsn;
2590 qi.tqi_cwmin = 2*ATH_EXPONENT_TO_VALUE(wmep->wmep_logcwmin);
2591 qi.tqi_cwmax = ATH_EXPONENT_TO_VALUE(wmep->wmep_logcwmax);
2594 if (!ath_hal_settxqueueprops(ah, sc->sc_bhalq, &qi)) {
2595 device_printf(sc->sc_dev, "unable to update parameters for "
2596 "beacon hardware queue!\n");
2599 ath_hal_resettxqueue(ah, sc->sc_bhalq); /* push to h/w */
2602 #undef ATH_EXPONENT_TO_VALUE
2606 * Allocate and setup an initial beacon frame.
2609 ath_beacon_alloc(struct ath_softc *sc, struct ieee80211_node *ni)
2611 struct ieee80211vap *vap = ni->ni_vap;
2612 struct ath_vap *avp = ATH_VAP(vap);
2618 if (bf->bf_m != NULL) {
2619 bus_dmamap_unload(sc->sc_dmat, bf->bf_dmamap);
2623 if (bf->bf_node != NULL) {
2624 ieee80211_free_node(bf->bf_node);
2629 * NB: the beacon data buffer must be 32-bit aligned;
2630 * we assume the mbuf routines will return us something
2631 * with this alignment (perhaps should assert).
2633 m = ieee80211_beacon_alloc(ni, &avp->av_boff);
2635 device_printf(sc->sc_dev, "%s: cannot get mbuf\n", __func__);
2636 sc->sc_stats.ast_be_nombuf++;
2639 error = bus_dmamap_load_mbuf_segment(sc->sc_dmat, bf->bf_dmamap, m,
2640 bf->bf_segs, 1, &bf->bf_nseg,
2643 device_printf(sc->sc_dev,
2644 "%s: cannot map mbuf, bus_dmamap_load_mbuf_segment returns %d\n",
2651 * Calculate a TSF adjustment factor required for staggered
2652 * beacons. Note that we assume the format of the beacon
2653 * frame leaves the tstamp field immediately following the
2656 if (sc->sc_stagbeacons && avp->av_bslot > 0) {
2658 struct ieee80211_frame *wh;
2661 * The beacon interval is in TU's; the TSF is in usecs.
2662 * We figure out how many TU's to add to align the timestamp
2663 * then convert to TSF units and handle byte swapping before
2664 * inserting it in the frame. The hardware will then add this
2665 * each time a beacon frame is sent. Note that we align vap's
2666 * 1..N and leave vap 0 untouched. This means vap 0 has a
2667 * timestamp in one beacon interval while the others get a
2668 * timstamp aligned to the next interval.
2670 tsfadjust = ni->ni_intval *
2671 (ATH_BCBUF - avp->av_bslot) / ATH_BCBUF;
2672 tsfadjust = htole64(tsfadjust << 10); /* TU -> TSF */
2674 DPRINTF(sc, ATH_DEBUG_BEACON,
2675 "%s: %s beacons bslot %d intval %u tsfadjust %llu\n",
2676 __func__, sc->sc_stagbeacons ? "stagger" : "burst",
2677 avp->av_bslot, ni->ni_intval,
2678 (long long unsigned) le64toh(tsfadjust));
2680 wh = mtod(m, struct ieee80211_frame *);
2681 memcpy(&wh[1], &tsfadjust, sizeof(tsfadjust));
2684 bf->bf_node = ieee80211_ref_node(ni);
2690 * Setup the beacon frame for transmit.
2693 ath_beacon_setup(struct ath_softc *sc, struct ath_buf *bf)
2695 #define USE_SHPREAMBLE(_ic) \
2696 (((_ic)->ic_flags & (IEEE80211_F_SHPREAMBLE | IEEE80211_F_USEBARKER))\
2697 == IEEE80211_F_SHPREAMBLE)
2698 struct ieee80211_node *ni = bf->bf_node;
2699 struct ieee80211com *ic = ni->ni_ic;
2700 struct mbuf *m = bf->bf_m;
2701 struct ath_hal *ah = sc->sc_ah;
2702 struct ath_desc *ds;
2704 const HAL_RATE_TABLE *rt;
2707 DPRINTF(sc, ATH_DEBUG_BEACON_PROC, "%s: m %p len %u\n",
2708 __func__, m, m->m_len);
2710 /* setup descriptors */
2713 flags = HAL_TXDESC_NOACK;
2714 if (ic->ic_opmode == IEEE80211_M_IBSS && sc->sc_hasveol) {
2715 ds->ds_link = bf->bf_daddr; /* self-linked */
2716 flags |= HAL_TXDESC_VEOL;
2718 * Let hardware handle antenna switching.
2720 antenna = sc->sc_txantenna;
2724 * Switch antenna every 4 beacons.
2725 * XXX assumes two antenna
2727 if (sc->sc_txantenna != 0)
2728 antenna = sc->sc_txantenna;
2729 else if (sc->sc_stagbeacons && sc->sc_nbcnvaps != 0)
2730 antenna = ((sc->sc_stats.ast_be_xmit / sc->sc_nbcnvaps) & 4 ? 2 : 1);
2732 antenna = (sc->sc_stats.ast_be_xmit & 4 ? 2 : 1);
2735 KASSERT(bf->bf_nseg == 1,
2736 ("multi-segment beacon frame; nseg %u", bf->bf_nseg));
2737 ds->ds_data = bf->bf_segs[0].ds_addr;
2739 * Calculate rate code.
2740 * XXX everything at min xmit rate
2743 rt = sc->sc_currates;
2744 rate = rt->info[rix].rateCode;
2745 if (USE_SHPREAMBLE(ic))
2746 rate |= rt->info[rix].shortPreamble;
2747 ath_hal_setuptxdesc(ah, ds
2748 , m->m_len + IEEE80211_CRC_LEN /* frame length */
2749 , sizeof(struct ieee80211_frame)/* header length */
2750 , HAL_PKT_TYPE_BEACON /* Atheros packet type */
2751 , ni->ni_txpower /* txpower XXX */
2752 , rate, 1 /* series 0 rate/tries */
2753 , HAL_TXKEYIX_INVALID /* no encryption */
2754 , antenna /* antenna mode */
2755 , flags /* no ack, veol for beacons */
2756 , 0 /* rts/cts rate */
2757 , 0 /* rts/cts duration */
2759 /* NB: beacon's BufLen must be a multiple of 4 bytes */
2760 ath_hal_filltxdesc(ah, ds
2761 , roundup(m->m_len, 4) /* buffer length */
2762 , AH_TRUE /* first segment */
2763 , AH_TRUE /* last segment */
2764 , ds /* first descriptor */
2769 #undef USE_SHPREAMBLE
2773 ath_beacon_update(struct ieee80211vap *vap, int item)
2775 struct ieee80211_beacon_offsets *bo = &ATH_VAP(vap)->av_boff;
2777 setbit(bo->bo_flags, item);
2781 * Append the contents of src to dst; both queues
2782 * are assumed to be locked.
2785 ath_txqmove(struct ath_txq *dst, struct ath_txq *src)
2787 STAILQ_CONCAT(&dst->axq_q, &src->axq_q);
2789 dst->axq_link = src->axq_link;
2790 src->axq_link = NULL;
2791 dst->axq_depth += src->axq_depth;
2796 * Transmit a beacon frame at SWBA. Dynamic updates to the
2797 * frame contents are done as needed and the slot time is
2798 * also adjusted based on current state.
2801 ath_beacon_proc(void *arg, int pending)
2803 struct ath_softc *sc = arg;
2804 struct ath_hal *ah = sc->sc_ah;
2805 struct ieee80211vap *vap;
2810 DPRINTF(sc, ATH_DEBUG_BEACON_PROC, "%s: pending %u\n",
2813 * Check if the previous beacon has gone out. If
2814 * not don't try to post another, skip this period
2815 * and wait for the next. Missed beacons indicate
2816 * a problem and should not occur. If we miss too
2817 * many consecutive beacons reset the device.
2819 if (ath_hal_numtxpending(ah, sc->sc_bhalq) != 0) {
2820 sc->sc_bmisscount++;
2821 DPRINTF(sc, ATH_DEBUG_BEACON,
2822 "%s: missed %u consecutive beacons\n",
2823 __func__, sc->sc_bmisscount);
2824 if (sc->sc_bmisscount >= ath_bstuck_threshold)
2825 taskqueue_enqueue(sc->sc_tq, &sc->sc_bstucktask);
2828 if (sc->sc_bmisscount != 0) {
2829 DPRINTF(sc, ATH_DEBUG_BEACON,
2830 "%s: resume beacon xmit after %u misses\n",
2831 __func__, sc->sc_bmisscount);
2832 sc->sc_bmisscount = 0;
2836 * Stop any current dma before messing with the beacon linkages.
2838 if (!ath_hal_stoptxdma(ah, sc->sc_bhalq)) {
2839 DPRINTF(sc, ATH_DEBUG_ANY,
2840 "%s: beacon queue %u did not stop?\n",
2841 __func__, sc->sc_bhalq);
2844 if (sc->sc_stagbeacons) { /* staggered beacons */
2845 struct ieee80211com *ic = sc->sc_ifp->if_l2com;
2848 tsftu = ath_hal_gettsf32(ah) >> 10;
2850 slot = ((tsftu % ic->ic_lintval) * ATH_BCBUF) / ic->ic_lintval;
2851 vap = sc->sc_bslot[(slot+1) % ATH_BCBUF];
2853 if (vap != NULL && vap->iv_state >= IEEE80211_S_RUN) {
2854 bf = ath_beacon_generate(sc, vap);
2856 bfaddr = bf->bf_daddr;
2858 } else { /* burst'd beacons */
2859 uint32_t *bflink = &bfaddr;
2861 for (slot = 0; slot < ATH_BCBUF; slot++) {
2862 vap = sc->sc_bslot[slot];
2863 if (vap != NULL && vap->iv_state >= IEEE80211_S_RUN) {
2864 bf = ath_beacon_generate(sc, vap);
2866 *bflink = bf->bf_daddr;
2867 bflink = &bf->bf_desc->ds_link;
2871 *bflink = 0; /* terminate list */
2875 * Handle slot time change when a non-ERP station joins/leaves
2876 * an 11g network. The 802.11 layer notifies us via callback,
2877 * we mark updateslot, then wait one beacon before effecting
2878 * the change. This gives associated stations at least one
2879 * beacon interval to note the state change.
2882 if (sc->sc_updateslot == UPDATE) {
2883 sc->sc_updateslot = COMMIT; /* commit next beacon */
2884 sc->sc_slotupdate = slot;
2885 } else if (sc->sc_updateslot == COMMIT && sc->sc_slotupdate == slot)
2886 ath_setslottime(sc); /* commit change to h/w */
2889 * Check recent per-antenna transmit statistics and flip
2890 * the default antenna if noticeably more frames went out
2891 * on the non-default antenna.
2892 * XXX assumes 2 anntenae
2894 if (!sc->sc_diversity && (!sc->sc_stagbeacons || slot == 0)) {
2895 otherant = sc->sc_defant & 1 ? 2 : 1;
2896 if (sc->sc_ant_tx[otherant] > sc->sc_ant_tx[sc->sc_defant] + 2)
2897 ath_setdefantenna(sc, otherant);
2898 sc->sc_ant_tx[1] = sc->sc_ant_tx[2] = 0;
2902 /* NB: cabq traffic should already be queued and primed */
2903 ath_hal_puttxbuf(ah, sc->sc_bhalq, bfaddr);
2904 sc->sc_stats.ast_be_xmit++;
2905 ath_hal_txstart(ah, sc->sc_bhalq);
2907 /* else no beacon will be generated */
2910 static struct ath_buf *
2911 ath_beacon_generate(struct ath_softc *sc, struct ieee80211vap *vap)
2913 struct ath_vap *avp = ATH_VAP(vap);
2914 struct ath_txq *cabq = sc->sc_cabq;
2919 KASSERT(vap->iv_state >= IEEE80211_S_RUN,
2920 ("not running, state %d", vap->iv_state));
2921 KASSERT(avp->av_bcbuf != NULL, ("no beacon buffer"));
2924 * Update dynamic beacon contents. If this returns
2925 * non-zero then we need to remap the memory because
2926 * the beacon frame changed size (probably because
2927 * of the TIM bitmap).
2931 nmcastq = avp->av_mcastq.axq_depth;
2932 if (ieee80211_beacon_update(bf->bf_node, &avp->av_boff, m, nmcastq)) {
2933 /* XXX too conservative? */
2934 bus_dmamap_unload(sc->sc_dmat, bf->bf_dmamap);
2935 error = bus_dmamap_load_mbuf_segment(sc->sc_dmat, bf->bf_dmamap, m,
2936 bf->bf_segs, 1, &bf->bf_nseg,
2939 if_printf(vap->iv_ifp,
2940 "%s: bus_dmamap_load_mbuf_segment failed, error %u\n",
2945 if ((avp->av_boff.bo_tim[4] & 1) && cabq->axq_depth) {
2946 DPRINTF(sc, ATH_DEBUG_BEACON,
2947 "%s: cabq did not drain, mcastq %u cabq %u\n",
2948 __func__, nmcastq, cabq->axq_depth);
2949 sc->sc_stats.ast_cabq_busy++;
2950 if (sc->sc_nvaps > 1 && sc->sc_stagbeacons) {
2952 * CABQ traffic from a previous vap is still pending.
2953 * We must drain the q before this beacon frame goes
2954 * out as otherwise this vap's stations will get cab
2955 * frames from a different vap.
2956 * XXX could be slow causing us to miss DBA
2958 ath_tx_draintxq(sc, cabq);
2961 ath_beacon_setup(sc, bf);
2962 bus_dmamap_sync(sc->sc_dmat, bf->bf_dmamap, BUS_DMASYNC_PREWRITE);
2965 * Enable the CAB queue before the beacon queue to
2966 * insure cab frames are triggered by this beacon.
2968 if (avp->av_boff.bo_tim[4] & 1) {
2969 struct ath_hal *ah = sc->sc_ah;
2971 /* NB: only at DTIM */
2973 struct ath_buf *bfm;
2977 * Move frames from the s/w mcast q to the h/w cab q.
2980 bfm = STAILQ_FIRST(&avp->av_mcastq.axq_q);
2981 qbusy = ath_hal_txqenabled(ah, cabq->axq_qnum);
2983 if (cabq->axq_link != NULL) {
2985 *cabq->axq_link = bfm->bf_daddr;
2986 cabq->axq_flags |= ATH_TXQ_PUTPENDING;
2989 ath_hal_puttxbuf(ah, cabq->axq_qnum,
2993 if (cabq->axq_link != NULL) {
2995 *cabq->axq_link = bfm->bf_daddr;
2997 cabq->axq_flags |= ATH_TXQ_PUTPENDING;
2999 ath_txqmove(cabq, &avp->av_mcastq);
3001 sc->sc_stats.ast_cabq_xmit += nmcastq;
3003 /* NB: gated by beacon so safe to start here */
3004 ath_hal_txstart(ah, cabq->axq_qnum);
3010 ath_beacon_start_adhoc(struct ath_softc *sc, struct ieee80211vap *vap)
3012 struct ath_vap *avp = ATH_VAP(vap);
3013 struct ath_hal *ah = sc->sc_ah;
3018 KASSERT(avp->av_bcbuf != NULL, ("no beacon buffer"));
3021 * Update dynamic beacon contents. If this returns
3022 * non-zero then we need to remap the memory because
3023 * the beacon frame changed size (probably because
3024 * of the TIM bitmap).
3028 if (ieee80211_beacon_update(bf->bf_node, &avp->av_boff, m, 0)) {
3029 /* XXX too conservative? */
3030 bus_dmamap_unload(sc->sc_dmat, bf->bf_dmamap);
3031 error = bus_dmamap_load_mbuf_segment(sc->sc_dmat, bf->bf_dmamap, m,
3032 bf->bf_segs, 1, &bf->bf_nseg,
3035 if_printf(vap->iv_ifp,
3036 "%s: bus_dmamap_load_mbuf_segment failed, error %u\n",
3041 ath_beacon_setup(sc, bf);
3042 bus_dmamap_sync(sc->sc_dmat, bf->bf_dmamap, BUS_DMASYNC_PREWRITE);
3044 /* NB: caller is known to have already stopped tx dma */
3045 ath_hal_puttxbuf(ah, sc->sc_bhalq, bf->bf_daddr);
3046 ath_hal_txstart(ah, sc->sc_bhalq);
3050 * Reset the hardware after detecting beacons have stopped.
3053 ath_bstuck_task(void *arg, int pending)
3055 struct ath_softc *sc = arg;
3056 struct ifnet *ifp = sc->sc_ifp;
3058 wlan_serialize_enter();
3059 if_printf(ifp, "stuck beacon; resetting (bmiss count %u)\n",
3061 sc->sc_stats.ast_bstuck++;
3063 wlan_serialize_exit();
3067 * Reclaim beacon resources and return buffer to the pool.
3070 ath_beacon_return(struct ath_softc *sc, struct ath_buf *bf)
3073 if (bf->bf_m != NULL) {
3074 bus_dmamap_unload(sc->sc_dmat, bf->bf_dmamap);
3078 if (bf->bf_node != NULL) {
3079 ieee80211_free_node(bf->bf_node);
3082 STAILQ_INSERT_TAIL(&sc->sc_bbuf, bf, bf_list);
3086 * Reclaim beacon resources.
3089 ath_beacon_free(struct ath_softc *sc)
3093 STAILQ_FOREACH(bf, &sc->sc_bbuf, bf_list) {
3094 if (bf->bf_m != NULL) {
3095 bus_dmamap_unload(sc->sc_dmat, bf->bf_dmamap);
3099 if (bf->bf_node != NULL) {
3100 ieee80211_free_node(bf->bf_node);
3107 * Configure the beacon and sleep timers.
3109 * When operating as an AP this resets the TSF and sets
3110 * up the hardware to notify us when we need to issue beacons.
3112 * When operating in station mode this sets up the beacon
3113 * timers according to the timestamp of the last received
3114 * beacon and the current TSF, configures PCF and DTIM
3115 * handling, programs the sleep registers so the hardware
3116 * will wakeup in time to receive beacons, and configures
3117 * the beacon miss handling so we'll receive a BMISS
3118 * interrupt when we stop seeing beacons from the AP
3119 * we've associated with.
3122 ath_beacon_config(struct ath_softc *sc, struct ieee80211vap *vap)
3124 #define TSF_TO_TU(_h,_l) \
3125 ((((u_int32_t)(_h)) << 22) | (((u_int32_t)(_l)) >> 10))
3127 struct ath_hal *ah = sc->sc_ah;
3128 struct ieee80211com *ic = sc->sc_ifp->if_l2com;
3129 struct ieee80211_node *ni;
3130 u_int32_t nexttbtt, intval, tsftu;
3134 vap = TAILQ_FIRST(&ic->ic_vaps); /* XXX */
3137 /* extract tstamp from last beacon and convert to TU */
3138 nexttbtt = TSF_TO_TU(LE_READ_4(ni->ni_tstamp.data + 4),
3139 LE_READ_4(ni->ni_tstamp.data));
3140 if (ic->ic_opmode == IEEE80211_M_HOSTAP ||
3141 ic->ic_opmode == IEEE80211_M_MBSS) {
3143 * For multi-bss ap/mesh support beacons are either staggered
3144 * evenly over N slots or burst together. For the former
3145 * arrange for the SWBA to be delivered for each slot.
3146 * Slots that are not occupied will generate nothing.
3148 /* NB: the beacon interval is kept internally in TU's */
3149 intval = ni->ni_intval & HAL_BEACON_PERIOD;
3150 if (sc->sc_stagbeacons)
3151 intval /= ATH_BCBUF;
3153 /* NB: the beacon interval is kept internally in TU's */
3154 intval = ni->ni_intval & HAL_BEACON_PERIOD;
3156 if (nexttbtt == 0) /* e.g. for ap mode */
3158 else if (intval) /* NB: can be 0 for monitor mode */
3159 nexttbtt = roundup(nexttbtt, intval);
3160 DPRINTF(sc, ATH_DEBUG_BEACON, "%s: nexttbtt %u intval %u (%u)\n",
3161 __func__, nexttbtt, intval, ni->ni_intval);
3162 if (ic->ic_opmode == IEEE80211_M_STA && !sc->sc_swbmiss) {
3163 HAL_BEACON_STATE bs;
3164 int dtimperiod, dtimcount;
3165 int cfpperiod, cfpcount;
3168 * Setup dtim and cfp parameters according to
3169 * last beacon we received (which may be none).
3171 dtimperiod = ni->ni_dtim_period;
3172 if (dtimperiod <= 0) /* NB: 0 if not known */
3174 dtimcount = ni->ni_dtim_count;
3175 if (dtimcount >= dtimperiod) /* NB: sanity check */
3176 dtimcount = 0; /* XXX? */
3177 cfpperiod = 1; /* NB: no PCF support yet */
3180 * Pull nexttbtt forward to reflect the current
3181 * TSF and calculate dtim+cfp state for the result.
3183 tsf = ath_hal_gettsf64(ah);
3184 tsftu = TSF_TO_TU(tsf>>32, tsf) + FUDGE;
3187 if (--dtimcount < 0) {
3188 dtimcount = dtimperiod - 1;
3190 cfpcount = cfpperiod - 1;
3192 } while (nexttbtt < tsftu);
3193 memset(&bs, 0, sizeof(bs));
3194 bs.bs_intval = intval;
3195 bs.bs_nexttbtt = nexttbtt;
3196 bs.bs_dtimperiod = dtimperiod*intval;
3197 bs.bs_nextdtim = bs.bs_nexttbtt + dtimcount*intval;
3198 bs.bs_cfpperiod = cfpperiod*bs.bs_dtimperiod;
3199 bs.bs_cfpnext = bs.bs_nextdtim + cfpcount*bs.bs_dtimperiod;
3200 bs.bs_cfpmaxduration = 0;
3203 * The 802.11 layer records the offset to the DTIM
3204 * bitmap while receiving beacons; use it here to
3205 * enable h/w detection of our AID being marked in
3206 * the bitmap vector (to indicate frames for us are
3207 * pending at the AP).
3208 * XXX do DTIM handling in s/w to WAR old h/w bugs
3209 * XXX enable based on h/w rev for newer chips
3211 bs.bs_timoffset = ni->ni_timoff;
3214 * Calculate the number of consecutive beacons to miss
3215 * before taking a BMISS interrupt.
3216 * Note that we clamp the result to at most 10 beacons.
3218 bs.bs_bmissthreshold = vap->iv_bmissthreshold;
3219 if (bs.bs_bmissthreshold > 10)
3220 bs.bs_bmissthreshold = 10;
3221 else if (bs.bs_bmissthreshold <= 0)
3222 bs.bs_bmissthreshold = 1;
3225 * Calculate sleep duration. The configuration is
3226 * given in ms. We insure a multiple of the beacon
3227 * period is used. Also, if the sleep duration is
3228 * greater than the DTIM period then it makes senses
3229 * to make it a multiple of that.
3231 * XXX fixed at 100ms
3233 bs.bs_sleepduration =
3234 roundup(IEEE80211_MS_TO_TU(100), bs.bs_intval);
3235 if (bs.bs_sleepduration > bs.bs_dtimperiod)
3236 bs.bs_sleepduration = roundup(bs.bs_sleepduration, bs.bs_dtimperiod);
3238 DPRINTF(sc, ATH_DEBUG_BEACON,
3239 "%s: tsf %ju tsf:tu %u intval %u nexttbtt %u dtim %u nextdtim %u bmiss %u sleep %u cfp:period %u maxdur %u next %u timoffset %u\n"
3246 , bs.bs_bmissthreshold
3247 , bs.bs_sleepduration
3249 , bs.bs_cfpmaxduration
3253 ath_hal_intrset(ah, 0);
3254 ath_hal_beacontimers(ah, &bs);
3255 sc->sc_imask |= HAL_INT_BMISS;
3256 ath_hal_intrset(ah, sc->sc_imask);
3258 ath_hal_intrset(ah, 0);
3259 if (nexttbtt == intval)
3260 intval |= HAL_BEACON_RESET_TSF;
3261 if (ic->ic_opmode == IEEE80211_M_IBSS) {
3263 * In IBSS mode enable the beacon timers but only
3264 * enable SWBA interrupts if we need to manually
3265 * prepare beacon frames. Otherwise we use a
3266 * self-linked tx descriptor and let the hardware
3269 intval |= HAL_BEACON_ENA;
3270 if (!sc->sc_hasveol)
3271 sc->sc_imask |= HAL_INT_SWBA;
3272 if ((intval & HAL_BEACON_RESET_TSF) == 0) {
3274 * Pull nexttbtt forward to reflect
3277 tsf = ath_hal_gettsf64(ah);
3278 tsftu = TSF_TO_TU(tsf>>32, tsf) + FUDGE;
3281 } while (nexttbtt < tsftu);
3283 ath_beaconq_config(sc);
3284 } else if (ic->ic_opmode == IEEE80211_M_HOSTAP ||
3285 ic->ic_opmode == IEEE80211_M_MBSS) {
3287 * In AP/mesh mode we enable the beacon timers
3288 * and SWBA interrupts to prepare beacon frames.
3290 intval |= HAL_BEACON_ENA;
3291 sc->sc_imask |= HAL_INT_SWBA; /* beacon prepare */
3292 ath_beaconq_config(sc);
3294 ath_hal_beaconinit(ah, nexttbtt, intval);
3295 sc->sc_bmisscount = 0;
3296 ath_hal_intrset(ah, sc->sc_imask);
3298 * When using a self-linked beacon descriptor in
3299 * ibss mode load it once here.
3301 if (ic->ic_opmode == IEEE80211_M_IBSS && sc->sc_hasveol)
3302 ath_beacon_start_adhoc(sc, vap);
3304 sc->sc_syncbeacon = 0;
3310 ath_load_cb(void *arg, bus_dma_segment_t *segs, int nsegs, int error)
3312 bus_addr_t *paddr = (bus_addr_t*) arg;
3313 KASSERT(error == 0, ("error %u on bus_dma callback", error));
3314 *paddr = segs->ds_addr;
3318 ath_descdma_setup(struct ath_softc *sc,
3319 struct ath_descdma *dd, ath_bufhead *head,
3320 const char *name, int nbuf, int ndesc)
3322 #define DS2PHYS(_dd, _ds) \
3323 ((_dd)->dd_desc_paddr + ((caddr_t)(_ds) - (caddr_t)(_dd)->dd_desc))
3324 struct ifnet *ifp = sc->sc_ifp;
3325 struct ath_desc *ds;
3327 int i, bsize, error;
3329 DPRINTF(sc, ATH_DEBUG_RESET, "%s: %s DMA: %u buffers %u desc/buf\n",
3330 __func__, name, nbuf, ndesc);
3333 dd->dd_desc_len = sizeof(struct ath_desc) * nbuf * ndesc;
3336 * Setup DMA descriptor area.
3338 error = bus_dma_tag_create(dd->dd_dmat, /* parent */
3339 PAGE_SIZE, 0, /* alignment, bounds */
3340 BUS_SPACE_MAXADDR_32BIT, /* lowaddr */
3341 BUS_SPACE_MAXADDR, /* highaddr */
3342 NULL, NULL, /* filter, filterarg */
3343 dd->dd_desc_len, /* maxsize */
3345 dd->dd_desc_len, /* maxsegsize */
3346 BUS_DMA_ALLOCNOW, /* flags */
3349 if_printf(ifp, "cannot allocate %s DMA tag\n", dd->dd_name);
3353 /* allocate descriptors */
3354 error = bus_dmamap_create(dd->dd_dmat, BUS_DMA_NOWAIT, &dd->dd_dmamap);
3356 if_printf(ifp, "unable to create dmamap for %s descriptors, "
3357 "error %u\n", dd->dd_name, error);
3361 error = bus_dmamem_alloc(dd->dd_dmat, (void**) &dd->dd_desc,
3362 BUS_DMA_NOWAIT | BUS_DMA_COHERENT,
3365 if_printf(ifp, "unable to alloc memory for %u %s descriptors, "
3366 "error %u\n", nbuf * ndesc, dd->dd_name, error);
3370 error = bus_dmamap_load(dd->dd_dmat, dd->dd_dmamap,
3371 dd->dd_desc, dd->dd_desc_len,
3372 ath_load_cb, &dd->dd_desc_paddr,
3375 if_printf(ifp, "unable to map %s descriptors, error %u\n",
3376 dd->dd_name, error);
3381 DPRINTF(sc, ATH_DEBUG_RESET, "%s: %s DMA map: %p (%lu) -> %p (%lu)\n",
3382 __func__, dd->dd_name, ds, (u_long) dd->dd_desc_len,
3383 (caddr_t) dd->dd_desc_paddr, /*XXX*/ (u_long) dd->dd_desc_len);
3385 /* allocate rx buffers */
3386 bsize = sizeof(struct ath_buf) * nbuf;
3387 bf = kmalloc(bsize, M_ATHDEV, M_INTWAIT | M_ZERO);
3391 for (i = 0; i < nbuf; i++, bf++, ds += ndesc) {
3393 bf->bf_daddr = DS2PHYS(dd, ds);
3394 error = bus_dmamap_create(sc->sc_dmat, BUS_DMA_NOWAIT,
3397 if_printf(ifp, "unable to create dmamap for %s "
3398 "buffer %u, error %u\n", dd->dd_name, i, error);
3399 ath_descdma_cleanup(sc, dd, head);
3402 STAILQ_INSERT_TAIL(head, bf, bf_list);
3406 bus_dmamem_free(dd->dd_dmat, dd->dd_desc, dd->dd_dmamap);
3408 bus_dmamap_destroy(dd->dd_dmat, dd->dd_dmamap);
3410 bus_dma_tag_destroy(dd->dd_dmat);
3411 memset(dd, 0, sizeof(*dd));
3417 ath_descdma_cleanup(struct ath_softc *sc,
3418 struct ath_descdma *dd, ath_bufhead *head)
3421 struct ieee80211_node *ni;
3423 bus_dmamap_unload(dd->dd_dmat, dd->dd_dmamap);
3424 bus_dmamem_free(dd->dd_dmat, dd->dd_desc, dd->dd_dmamap);
3425 bus_dmamap_destroy(dd->dd_dmat, dd->dd_dmamap);
3426 bus_dma_tag_destroy(dd->dd_dmat);
3428 STAILQ_FOREACH(bf, head, bf_list) {
3433 if (bf->bf_dmamap != NULL) {
3434 bus_dmamap_destroy(sc->sc_dmat, bf->bf_dmamap);
3435 bf->bf_dmamap = NULL;
3441 * Reclaim node reference.
3443 ieee80211_free_node(ni);
3448 kfree(dd->dd_bufptr, M_ATHDEV);
3449 memset(dd, 0, sizeof(*dd));
3453 ath_desc_alloc(struct ath_softc *sc)
3457 error = ath_descdma_setup(sc, &sc->sc_rxdma, &sc->sc_rxbuf,
3458 "rx", ath_rxbuf, 1);
3462 error = ath_descdma_setup(sc, &sc->sc_txdma, &sc->sc_txbuf,
3463 "tx", ath_txbuf, ATH_TXDESC);
3465 ath_descdma_cleanup(sc, &sc->sc_rxdma, &sc->sc_rxbuf);
3469 error = ath_descdma_setup(sc, &sc->sc_bdma, &sc->sc_bbuf,
3470 "beacon", ATH_BCBUF, 1);
3472 ath_descdma_cleanup(sc, &sc->sc_txdma, &sc->sc_txbuf);
3473 ath_descdma_cleanup(sc, &sc->sc_rxdma, &sc->sc_rxbuf);
3480 ath_desc_free(struct ath_softc *sc)
3483 if (sc->sc_bdma.dd_desc_len != 0)
3484 ath_descdma_cleanup(sc, &sc->sc_bdma, &sc->sc_bbuf);
3485 if (sc->sc_txdma.dd_desc_len != 0)
3486 ath_descdma_cleanup(sc, &sc->sc_txdma, &sc->sc_txbuf);
3487 if (sc->sc_rxdma.dd_desc_len != 0)
3488 ath_descdma_cleanup(sc, &sc->sc_rxdma, &sc->sc_rxbuf);
3491 static struct ieee80211_node *
3492 ath_node_alloc(struct ieee80211vap *vap, const uint8_t mac[IEEE80211_ADDR_LEN])
3494 struct ieee80211com *ic = vap->iv_ic;
3495 struct ath_softc *sc = ic->ic_ifp->if_softc;
3496 const size_t space = sizeof(struct ath_node) + sc->sc_rc->arc_space;
3497 struct ath_node *an;
3499 an = kmalloc(space, M_80211_NODE, M_INTWAIT|M_ZERO);
3500 ath_rate_node_init(sc, an);
3502 DPRINTF(sc, ATH_DEBUG_NODE, "%s: an %p\n", __func__, an);
3503 return &an->an_node;
3507 ath_node_free(struct ieee80211_node *ni)
3509 struct ieee80211com *ic = ni->ni_ic;
3510 struct ath_softc *sc = ic->ic_ifp->if_softc;
3512 DPRINTF(sc, ATH_DEBUG_NODE, "%s: ni %p\n", __func__, ni);
3514 ath_rate_node_cleanup(sc, ATH_NODE(ni));
3515 sc->sc_node_free(ni);
3519 ath_node_getsignal(const struct ieee80211_node *ni, int8_t *rssi, int8_t *noise)
3521 struct ieee80211com *ic = ni->ni_ic;
3522 struct ath_softc *sc = ic->ic_ifp->if_softc;
3523 struct ath_hal *ah = sc->sc_ah;
3525 *rssi = ic->ic_node_getrssi(ni);
3526 if (ni->ni_chan != IEEE80211_CHAN_ANYC)
3527 *noise = ath_hal_getchannoise(ah, ni->ni_chan);
3529 *noise = -95; /* nominally correct */
3533 ath_rxbuf_init(struct ath_softc *sc, struct ath_buf *bf)
3535 struct ath_hal *ah = sc->sc_ah;
3538 struct ath_desc *ds;
3543 * NB: by assigning a page to the rx dma buffer we
3544 * implicitly satisfy the Atheros requirement that
3545 * this buffer be cache-line-aligned and sized to be
3546 * multiple of the cache line size. Not doing this
3547 * causes weird stuff to happen (for the 5210 at least).
3549 m = m_getcl(MB_WAIT, MT_DATA, M_PKTHDR);
3551 kprintf("ath_rxbuf_init: no mbuf\n");
3552 DPRINTF(sc, ATH_DEBUG_ANY,
3553 "%s: no mbuf/cluster\n", __func__);
3554 sc->sc_stats.ast_rx_nombuf++;
3557 m->m_pkthdr.len = m->m_len = m->m_ext.ext_size;
3559 error = bus_dmamap_load_mbuf_segment(sc->sc_dmat,
3561 bf->bf_segs, 1, &bf->bf_nseg,
3564 DPRINTF(sc, ATH_DEBUG_ANY,
3565 "%s: bus_dmamap_load_mbuf_segment failed; error %d\n",
3567 sc->sc_stats.ast_rx_busdma++;
3571 KASSERT(bf->bf_nseg == 1,
3572 ("multi-segment packet; nseg %u", bf->bf_nseg));
3575 bus_dmamap_sync(sc->sc_dmat, bf->bf_dmamap, BUS_DMASYNC_PREREAD);
3578 * Setup descriptors. For receive we always terminate
3579 * the descriptor list with a self-linked entry so we'll
3580 * not get overrun under high load (as can happen with a
3581 * 5212 when ANI processing enables PHY error frames).
3583 * To insure the last descriptor is self-linked we create
3584 * each descriptor as self-linked and add it to the end. As
3585 * each additional descriptor is added the previous self-linked
3586 * entry is ``fixed'' naturally. This should be safe even
3587 * if DMA is happening. When processing RX interrupts we
3588 * never remove/process the last, self-linked, entry on the
3589 * descriptor list. This insures the hardware always has
3590 * someplace to write a new frame.
3593 ds->ds_link = bf->bf_daddr; /* link to self */
3594 ds->ds_data = bf->bf_segs[0].ds_addr;
3595 ath_hal_setuprxdesc(ah, ds
3596 , m->m_len /* buffer size */
3600 if (sc->sc_rxlink != NULL)
3601 *sc->sc_rxlink = bf->bf_daddr;
3602 sc->sc_rxlink = &ds->ds_link;
3607 * Extend 15-bit time stamp from rx descriptor to
3608 * a full 64-bit TSF using the specified TSF.
3610 static __inline u_int64_t
3611 ath_extend_tsf(u_int32_t rstamp, u_int64_t tsf)
3613 if ((tsf & 0x7fff) < rstamp)
3615 return ((tsf &~ 0x7fff) | rstamp);
3619 * Intercept management frames to collect beacon rssi data
3620 * and to do ibss merges.
3623 ath_recv_mgmt(struct ieee80211_node *ni, struct mbuf *m,
3624 int subtype, int rssi, int nf)
3626 struct ieee80211vap *vap = ni->ni_vap;
3627 struct ath_softc *sc = vap->iv_ic->ic_ifp->if_softc;
3630 * Call up first so subsequent work can use information
3631 * potentially stored in the node (e.g. for ibss merge).
3633 ATH_VAP(vap)->av_recv_mgmt(ni, m, subtype, rssi, nf);
3635 case IEEE80211_FC0_SUBTYPE_BEACON:
3636 /* update rssi statistics for use by the hal */
3637 ATH_RSSI_LPF(sc->sc_halstats.ns_avgbrssi, rssi);
3638 if (sc->sc_syncbeacon &&
3639 ni == vap->iv_bss && vap->iv_state == IEEE80211_S_RUN) {
3641 * Resync beacon timers using the tsf of the beacon
3642 * frame we just received.
3644 ath_beacon_config(sc, vap);
3647 case IEEE80211_FC0_SUBTYPE_PROBE_RESP:
3648 if (vap->iv_opmode == IEEE80211_M_IBSS &&
3649 vap->iv_state == IEEE80211_S_RUN) {
3650 uint32_t rstamp = sc->sc_lastrs->rs_tstamp;
3651 u_int64_t tsf = ath_extend_tsf(rstamp,
3652 ath_hal_gettsf64(sc->sc_ah));
3654 * Handle ibss merge as needed; check the tsf on the
3655 * frame before attempting the merge. The 802.11 spec
3656 * says the station should change it's bssid to match
3657 * the oldest station with the same ssid, where oldest
3658 * is determined by the tsf. Note that hardware
3659 * reconfiguration happens through callback to
3660 * ath_newstate as the state machine will go from
3661 * RUN -> RUN when this happens.
3663 if (le64toh(ni->ni_tstamp.tsf) >= tsf) {
3664 DPRINTF(sc, ATH_DEBUG_STATE,
3665 "ibss merge, rstamp %u tsf %ju "
3666 "tstamp %ju\n", rstamp, (uintmax_t)tsf,
3667 (uintmax_t)ni->ni_tstamp.tsf);
3668 (void) ieee80211_ibss_merge(ni);
3676 * Set the default antenna.
3679 ath_setdefantenna(struct ath_softc *sc, u_int antenna)
3681 struct ath_hal *ah = sc->sc_ah;
3683 /* XXX block beacon interrupts */
3684 ath_hal_setdefantenna(ah, antenna);
3685 if (sc->sc_defant != antenna)
3686 sc->sc_stats.ast_ant_defswitch++;
3687 sc->sc_defant = antenna;
3688 sc->sc_rxotherant = 0;
3692 ath_rx_tap(struct ifnet *ifp, struct mbuf *m,
3693 const struct ath_rx_status *rs, u_int64_t tsf, int16_t nf)
3695 #define CHAN_HT20 htole32(IEEE80211_CHAN_HT20)
3696 #define CHAN_HT40U htole32(IEEE80211_CHAN_HT40U)
3697 #define CHAN_HT40D htole32(IEEE80211_CHAN_HT40D)
3698 #define CHAN_HT (CHAN_HT20|CHAN_HT40U|CHAN_HT40D)
3699 struct ath_softc *sc = ifp->if_softc;
3700 const HAL_RATE_TABLE *rt;
3703 rt = sc->sc_currates;
3704 KASSERT(rt != NULL, ("no rate table, mode %u", sc->sc_curmode));
3705 rix = rt->rateCodeToIndex[rs->rs_rate];
3706 sc->sc_rx_th.wr_rate = sc->sc_hwmap[rix].ieeerate;
3707 sc->sc_rx_th.wr_flags = sc->sc_hwmap[rix].rxflags;
3708 #ifdef AH_SUPPORT_AR5416
3709 sc->sc_rx_th.wr_chan_flags &= ~CHAN_HT;
3710 if (sc->sc_rx_th.wr_rate & IEEE80211_RATE_MCS) { /* HT rate */
3711 struct ieee80211com *ic = ifp->if_l2com;
3713 if ((rs->rs_flags & HAL_RX_2040) == 0)
3714 sc->sc_rx_th.wr_chan_flags |= CHAN_HT20;
3715 else if (IEEE80211_IS_CHAN_HT40U(ic->ic_curchan))
3716 sc->sc_rx_th.wr_chan_flags |= CHAN_HT40U;
3718 sc->sc_rx_th.wr_chan_flags |= CHAN_HT40D;
3719 if ((rs->rs_flags & HAL_RX_GI) == 0)
3720 sc->sc_rx_th.wr_flags |= IEEE80211_RADIOTAP_F_SHORTGI;
3723 sc->sc_rx_th.wr_tsf = htole64(ath_extend_tsf(rs->rs_tstamp, tsf));
3724 if (rs->rs_status & HAL_RXERR_CRC)
3725 sc->sc_rx_th.wr_flags |= IEEE80211_RADIOTAP_F_BADFCS;
3726 /* XXX propagate other error flags from descriptor */
3727 sc->sc_rx_th.wr_antnoise = nf;
3728 sc->sc_rx_th.wr_antsignal = nf + rs->rs_rssi;
3729 sc->sc_rx_th.wr_antenna = rs->rs_antenna;
3737 ath_handle_micerror(struct ieee80211com *ic,
3738 struct ieee80211_frame *wh, int keyix)
3740 struct ieee80211_node *ni;
3742 /* XXX recheck MIC to deal w/ chips that lie */
3743 /* XXX discard MIC errors on !data frames */
3744 ni = ieee80211_find_rxnode(ic, (const struct ieee80211_frame_min *) wh);
3746 ieee80211_notify_michael_failure(ni->ni_vap, wh, keyix);
3747 ieee80211_free_node(ni);
3752 ath_rx_task(void *arg, int npending)
3754 #define PA2DESC(_sc, _pa) \
3755 ((struct ath_desc *)((caddr_t)(_sc)->sc_rxdma.dd_desc + \
3756 ((_pa) - (_sc)->sc_rxdma.dd_desc_paddr)))
3757 struct ath_softc *sc = arg;
3760 struct ieee80211com *ic;
3762 struct ath_desc *ds;
3763 struct ath_rx_status *rs;
3765 struct ieee80211_node *ni;
3766 int len, type, ngood;
3772 wlan_serialize_enter();
3777 DPRINTF(sc, ATH_DEBUG_RX_PROC, "%s: pending %u\n", __func__, npending);
3779 nf = ath_hal_getchannoise(ah, sc->sc_curchan);
3780 sc->sc_stats.ast_rx_noise = nf;
3781 tsf = ath_hal_gettsf64(ah);
3783 bf = STAILQ_FIRST(&sc->sc_rxbuf);
3784 if (bf == NULL) { /* NB: shouldn't happen */
3785 if_printf(ifp, "%s: no buffer!\n", __func__);
3789 if (m == NULL) { /* NB: shouldn't happen */
3791 * If mbuf allocation failed previously there
3792 * will be no mbuf; try again to re-populate it.
3794 /* XXX make debug msg */
3795 if_printf(ifp, "%s: no mbuf!\n", __func__);
3796 STAILQ_REMOVE_HEAD(&sc->sc_rxbuf, bf_list);
3800 if (ds->ds_link == bf->bf_daddr) {
3801 /* NB: never process the self-linked entry at the end */
3804 /* XXX sync descriptor memory */
3806 * Must provide the virtual address of the current
3807 * descriptor, the physical address, and the virtual
3808 * address of the next descriptor in the h/w chain.
3809 * This allows the HAL to look ahead to see if the
3810 * hardware is done with a descriptor by checking the
3811 * done bit in the following descriptor and the address
3812 * of the current descriptor the DMA engine is working
3813 * on. All this is necessary because of our use of
3814 * a self-linked list to avoid rx overruns.
3816 rs = &bf->bf_status.ds_rxstat;
3817 status = ath_hal_rxprocdesc(ah, ds,
3818 bf->bf_daddr, PA2DESC(sc, ds->ds_link), rs);
3820 if (sc->sc_debug & ATH_DEBUG_RECV_DESC)
3821 ath_printrxbuf(sc, bf, 0, status == HAL_OK);
3823 if (status == HAL_EINPROGRESS)
3825 STAILQ_REMOVE_HEAD(&sc->sc_rxbuf, bf_list);
3826 if (rs->rs_status != 0) {
3827 if (rs->rs_status & HAL_RXERR_CRC)
3828 sc->sc_stats.ast_rx_crcerr++;
3829 if (rs->rs_status & HAL_RXERR_FIFO)
3830 sc->sc_stats.ast_rx_fifoerr++;
3831 if (rs->rs_status & HAL_RXERR_PHY) {
3832 sc->sc_stats.ast_rx_phyerr++;
3833 phyerr = rs->rs_phyerr & 0x1f;
3834 sc->sc_stats.ast_rx_phy[phyerr]++;
3835 goto rx_error; /* NB: don't count in ierrors */
3837 if (rs->rs_status & HAL_RXERR_DECRYPT) {
3839 * Decrypt error. If the error occurred
3840 * because there was no hardware key, then
3841 * let the frame through so the upper layers
3842 * can process it. This is necessary for 5210
3843 * parts which have no way to setup a ``clear''
3846 * XXX do key cache faulting
3848 if (rs->rs_keyix == HAL_RXKEYIX_INVALID)
3850 sc->sc_stats.ast_rx_badcrypt++;
3852 if (rs->rs_status & HAL_RXERR_MIC) {
3853 sc->sc_stats.ast_rx_badmic++;
3855 * Do minimal work required to hand off
3856 * the 802.11 header for notification.
3858 /* XXX frag's and qos frames */
3859 len = rs->rs_datalen;
3860 if (len >= sizeof (struct ieee80211_frame)) {
3861 bus_dmamap_sync(sc->sc_dmat,
3863 BUS_DMASYNC_POSTREAD);
3864 ath_handle_micerror(ic,
3865 mtod(m, struct ieee80211_frame *),
3867 rs->rs_keyix-32 : rs->rs_keyix);
3873 * Cleanup any pending partial frame.
3875 if (sc->sc_rxpending != NULL) {
3876 m_freem(sc->sc_rxpending);
3877 sc->sc_rxpending = NULL;
3880 * When a tap is present pass error frames
3881 * that have been requested. By default we
3882 * pass decrypt+mic errors but others may be
3883 * interesting (e.g. crc).
3885 if (ieee80211_radiotap_active(ic) &&
3886 (rs->rs_status & sc->sc_monpass)) {
3887 bus_dmamap_sync(sc->sc_dmat, bf->bf_dmamap,
3888 BUS_DMASYNC_POSTREAD);
3889 /* NB: bpf needs the mbuf length setup */
3890 len = rs->rs_datalen;
3891 m->m_pkthdr.len = m->m_len = len;
3892 ath_rx_tap(ifp, m, rs, tsf, nf);
3893 ieee80211_radiotap_rx_all(ic, m);
3895 /* XXX pass MIC errors up for s/w reclaculation */
3900 * Sync and unmap the frame. At this point we're
3901 * committed to passing the mbuf somewhere so clear
3902 * bf_m; this means a new mbuf must be allocated
3903 * when the rx descriptor is setup again to receive
3906 bus_dmamap_sync(sc->sc_dmat, bf->bf_dmamap,
3907 BUS_DMASYNC_POSTREAD);
3908 bus_dmamap_unload(sc->sc_dmat, bf->bf_dmamap);
3911 len = rs->rs_datalen;
3916 * Frame spans multiple descriptors; save
3917 * it for the next completed descriptor, it
3918 * will be used to construct a jumbogram.
3920 if (sc->sc_rxpending != NULL) {
3921 /* NB: max frame size is currently 2 clusters */
3922 sc->sc_stats.ast_rx_toobig++;
3923 m_freem(sc->sc_rxpending);
3925 m->m_pkthdr.rcvif = ifp;
3926 m->m_pkthdr.len = len;
3927 sc->sc_rxpending = m;
3929 } else if (sc->sc_rxpending != NULL) {
3931 * This is the second part of a jumbogram,
3932 * chain it to the first mbuf, adjust the
3933 * frame length, and clear the rxpending state.
3935 sc->sc_rxpending->m_next = m;
3936 sc->sc_rxpending->m_pkthdr.len += len;
3937 m = sc->sc_rxpending;
3938 sc->sc_rxpending = NULL;
3941 * Normal single-descriptor receive; setup
3942 * the rcvif and packet length.
3944 m->m_pkthdr.rcvif = ifp;
3945 m->m_pkthdr.len = len;
3949 sc->sc_stats.ast_ant_rx[rs->rs_antenna]++;
3952 * Populate the rx status block. When there are bpf
3953 * listeners we do the additional work to provide
3954 * complete status. Otherwise we fill in only the
3955 * material required by ieee80211_input. Note that
3956 * noise setting is filled in above.
3958 if (ieee80211_radiotap_active(ic))
3959 ath_rx_tap(ifp, m, rs, tsf, nf);
3962 * From this point on we assume the frame is at least
3963 * as large as ieee80211_frame_min; verify that.
3965 if (len < IEEE80211_MIN_LEN) {
3966 if (!ieee80211_radiotap_active(ic)) {
3967 DPRINTF(sc, ATH_DEBUG_RECV,
3968 "%s: short packet %d\n", __func__, len);
3969 sc->sc_stats.ast_rx_tooshort++;
3971 /* NB: in particular this captures ack's */
3972 ieee80211_radiotap_rx_all(ic, m);
3978 if (IFF_DUMPPKTS(sc, ATH_DEBUG_RECV)) {
3979 const HAL_RATE_TABLE *rt = sc->sc_currates;
3980 uint8_t rix = rt->rateCodeToIndex[rs->rs_rate];
3982 ieee80211_dump_pkt(ic, mtod(m, caddr_t), len,
3983 sc->sc_hwmap[rix].ieeerate, rs->rs_rssi);
3986 m_adj(m, -IEEE80211_CRC_LEN);
3989 * Locate the node for sender, track state, and then
3990 * pass the (referenced) node up to the 802.11 layer
3993 ni = ieee80211_find_rxnode_withkey(ic,
3994 mtod(m, const struct ieee80211_frame_min *),
3995 rs->rs_keyix == HAL_RXKEYIX_INVALID ?
3996 IEEE80211_KEYIX_NONE : rs->rs_keyix);
3999 * Sending station is known, dispatch directly.
4002 type = ieee80211_input(ni, m, rs->rs_rssi, nf);
4003 ieee80211_free_node(ni);
4005 * Arrange to update the last rx timestamp only for
4006 * frames from our ap when operating in station mode.
4007 * This assumes the rx key is always setup when
4010 if (ic->ic_opmode == IEEE80211_M_STA &&
4011 rs->rs_keyix != HAL_RXKEYIX_INVALID)
4014 type = ieee80211_input_all(ic, m, rs->rs_rssi, nf);
4017 * Track rx rssi and do any rx antenna management.
4019 ATH_RSSI_LPF(sc->sc_halstats.ns_avgrssi, rs->rs_rssi);
4020 if (sc->sc_diversity) {
4022 * When using fast diversity, change the default rx
4023 * antenna if diversity chooses the other antenna 3
4026 if (sc->sc_defant != rs->rs_antenna) {
4027 if (++sc->sc_rxotherant >= 3)
4028 ath_setdefantenna(sc, rs->rs_antenna);
4030 sc->sc_rxotherant = 0;
4032 if (sc->sc_softled) {
4034 * Blink for any data frame. Otherwise do a
4035 * heartbeat-style blink when idle. The latter
4036 * is mainly for station mode where we depend on
4037 * periodic beacon frames to trigger the poll event.
4039 if (type == IEEE80211_FC0_TYPE_DATA) {
4040 const HAL_RATE_TABLE *rt = sc->sc_currates;
4042 rt->rateCodeToIndex[rs->rs_rate]);
4043 } else if (ticks - sc->sc_ledevent >= sc->sc_ledidle)
4044 ath_led_event(sc, 0);
4047 STAILQ_INSERT_TAIL(&sc->sc_rxbuf, bf, bf_list);
4048 } while (ath_rxbuf_init(sc, bf) == 0);
4050 /* rx signal state monitoring */
4051 ath_hal_rxmonitor(ah, &sc->sc_halstats, sc->sc_curchan);
4053 sc->sc_lastrx = tsf;
4055 if ((ifp->if_flags & IFF_OACTIVE) == 0) {
4056 #ifdef IEEE80211_SUPPORT_SUPERG
4057 ieee80211_ff_age_all(ic, 100);
4059 if (!ifq_is_empty(&ifp->if_snd))
4062 wlan_serialize_exit();
4067 ath_txq_init(struct ath_softc *sc, struct ath_txq *txq, int qnum)
4069 txq->axq_qnum = qnum;
4072 txq->axq_intrcnt = 0;
4073 txq->axq_link = NULL;
4074 STAILQ_INIT(&txq->axq_q);
4078 * Setup a h/w transmit queue.
4080 static struct ath_txq *
4081 ath_txq_setup(struct ath_softc *sc, int qtype, int subtype)
4083 struct ath_hal *ah = sc->sc_ah;
4087 memset(&qi, 0, sizeof(qi));
4088 qi.tqi_subtype = subtype;
4089 qi.tqi_aifs = HAL_TXQ_USEDEFAULT;
4090 qi.tqi_cwmin = HAL_TXQ_USEDEFAULT;
4091 qi.tqi_cwmax = HAL_TXQ_USEDEFAULT;
4093 * Enable interrupts only for EOL and DESC conditions.
4094 * We mark tx descriptors to receive a DESC interrupt
4095 * when a tx queue gets deep; otherwise waiting for the
4096 * EOL to reap descriptors. Note that this is done to
4097 * reduce interrupt load and this only defers reaping
4098 * descriptors, never transmitting frames. Aside from
4099 * reducing interrupts this also permits more concurrency.
4100 * The only potential downside is if the tx queue backs
4101 * up in which case the top half of the kernel may backup
4102 * due to a lack of tx descriptors.
4104 qi.tqi_qflags = HAL_TXQ_TXEOLINT_ENABLE | HAL_TXQ_TXDESCINT_ENABLE;
4105 qnum = ath_hal_setuptxqueue(ah, qtype, &qi);
4108 * NB: don't print a message, this happens
4109 * normally on parts with too few tx queues
4113 if (qnum >= NELEM(sc->sc_txq)) {
4114 device_printf(sc->sc_dev,
4115 "hal qnum %u out of range, max %zu!\n",
4116 qnum, NELEM(sc->sc_txq));
4117 ath_hal_releasetxqueue(ah, qnum);
4120 if (!ATH_TXQ_SETUP(sc, qnum)) {
4121 ath_txq_init(sc, &sc->sc_txq[qnum], qnum);
4122 sc->sc_txqsetup |= 1<<qnum;
4124 return &sc->sc_txq[qnum];
4128 * Setup a hardware data transmit queue for the specified
4129 * access control. The hal may not support all requested
4130 * queues in which case it will return a reference to a
4131 * previously setup queue. We record the mapping from ac's
4132 * to h/w queues for use by ath_tx_start and also track
4133 * the set of h/w queues being used to optimize work in the
4134 * transmit interrupt handler and related routines.
4137 ath_tx_setup(struct ath_softc *sc, int ac, int haltype)
4139 struct ath_txq *txq;
4141 if (ac >= NELEM(sc->sc_ac2q)) {
4142 device_printf(sc->sc_dev, "AC %u out of range, max %zu!\n",
4143 ac, NELEM(sc->sc_ac2q));
4146 txq = ath_txq_setup(sc, HAL_TX_QUEUE_DATA, haltype);
4149 sc->sc_ac2q[ac] = txq;
4156 * Update WME parameters for a transmit queue.
4159 ath_txq_update(struct ath_softc *sc, int ac)
4161 #define ATH_EXPONENT_TO_VALUE(v) ((1<<v)-1)
4162 #define ATH_TXOP_TO_US(v) (v<<5)
4163 struct ifnet *ifp = sc->sc_ifp;
4164 struct ieee80211com *ic = ifp->if_l2com;
4165 struct ath_txq *txq = sc->sc_ac2q[ac];
4166 struct wmeParams *wmep = &ic->ic_wme.wme_chanParams.cap_wmeParams[ac];
4167 struct ath_hal *ah = sc->sc_ah;
4170 ath_hal_gettxqueueprops(ah, txq->axq_qnum, &qi);
4171 #ifdef IEEE80211_SUPPORT_TDMA
4174 * AIFS is zero so there's no pre-transmit wait. The
4175 * burst time defines the slot duration and is configured
4176 * through net80211. The QCU is setup to not do post-xmit
4177 * back off, lockout all lower-priority QCU's, and fire
4178 * off the DMA beacon alert timer which is setup based
4179 * on the slot configuration.
4181 qi.tqi_qflags = HAL_TXQ_TXOKINT_ENABLE
4182 | HAL_TXQ_TXERRINT_ENABLE
4183 | HAL_TXQ_TXURNINT_ENABLE
4184 | HAL_TXQ_TXEOLINT_ENABLE
4186 | HAL_TXQ_BACKOFF_DISABLE
4187 | HAL_TXQ_ARB_LOCKOUT_GLOBAL
4191 qi.tqi_readyTime = sc->sc_tdmaslotlen;
4192 qi.tqi_burstTime = qi.tqi_readyTime;
4195 qi.tqi_qflags = HAL_TXQ_TXOKINT_ENABLE
4196 | HAL_TXQ_TXERRINT_ENABLE
4197 | HAL_TXQ_TXDESCINT_ENABLE
4198 | HAL_TXQ_TXURNINT_ENABLE
4200 qi.tqi_aifs = wmep->wmep_aifsn;
4201 qi.tqi_cwmin = ATH_EXPONENT_TO_VALUE(wmep->wmep_logcwmin);
4202 qi.tqi_cwmax = ATH_EXPONENT_TO_VALUE(wmep->wmep_logcwmax);
4203 qi.tqi_readyTime = 0;
4204 qi.tqi_burstTime = ATH_TXOP_TO_US(wmep->wmep_txopLimit);
4205 #ifdef IEEE80211_SUPPORT_TDMA
4209 DPRINTF(sc, ATH_DEBUG_RESET,
4210 "%s: Q%u qflags 0x%x aifs %u cwmin %u cwmax %u burstTime %u\n",
4211 __func__, txq->axq_qnum, qi.tqi_qflags,
4212 qi.tqi_aifs, qi.tqi_cwmin, qi.tqi_cwmax, qi.tqi_burstTime);
4214 if (!ath_hal_settxqueueprops(ah, txq->axq_qnum, &qi)) {
4215 if_printf(ifp, "unable to update hardware queue "
4216 "parameters for %s traffic!\n",
4217 ieee80211_wme_acnames[ac]);
4220 ath_hal_resettxqueue(ah, txq->axq_qnum); /* push to h/w */
4223 #undef ATH_TXOP_TO_US
4224 #undef ATH_EXPONENT_TO_VALUE
4228 * Callback from the 802.11 layer to update WME parameters.
4231 ath_wme_update(struct ieee80211com *ic)
4233 struct ath_softc *sc = ic->ic_ifp->if_softc;
4235 return !ath_txq_update(sc, WME_AC_BE) ||
4236 !ath_txq_update(sc, WME_AC_BK) ||
4237 !ath_txq_update(sc, WME_AC_VI) ||
4238 !ath_txq_update(sc, WME_AC_VO) ? EIO : 0;
4242 * Reclaim resources for a setup queue.
4245 ath_tx_cleanupq(struct ath_softc *sc, struct ath_txq *txq)
4248 ath_hal_releasetxqueue(sc->sc_ah, txq->axq_qnum);
4249 sc->sc_txqsetup &= ~(1<<txq->axq_qnum);
4253 * Reclaim all tx queue resources.
4256 ath_tx_cleanup(struct ath_softc *sc)
4260 for (i = 0; i < HAL_NUM_TX_QUEUES; i++)
4261 if (ATH_TXQ_SETUP(sc, i))
4262 ath_tx_cleanupq(sc, &sc->sc_txq[i]);
4266 * Return h/w rate index for an IEEE rate (w/o basic rate bit)
4267 * using the current rates in sc_rixmap.
4270 ath_tx_findrix(const struct ath_softc *sc, uint8_t rate)
4272 int rix = sc->sc_rixmap[rate];
4273 /* NB: return lowest rix for invalid rate */
4274 return (rix == 0xff ? 0 : rix);
4278 * Reclaim mbuf resources. For fragmented frames we
4279 * need to claim each frag chained with m_nextpkt.
4282 ath_freetx(struct mbuf *m)
4287 next = m->m_nextpkt;
4288 m->m_nextpkt = NULL;
4290 } while ((m = next) != NULL);
4294 ath_tx_dmasetup(struct ath_softc *sc, struct ath_buf *bf, struct mbuf *m0)
4300 * Load the DMA map so any coalescing is done. This
4301 * also calculates the number of descriptors we need.
4303 error = bus_dmamap_load_mbuf_defrag(sc->sc_dmat, bf->bf_dmamap, &m0,
4304 bf->bf_segs, ATH_TXDESC,
4305 &bf->bf_nseg, BUS_DMA_NOWAIT);
4307 sc->sc_stats.ast_tx_busdma++;
4313 * Discard null packets.
4315 if (bf->bf_nseg == 0) { /* null packet, discard */
4316 sc->sc_stats.ast_tx_nodata++;
4320 DPRINTF(sc, ATH_DEBUG_XMIT, "%s: m %p len %u\n",
4321 __func__, m0, m0->m_pkthdr.len);
4322 bus_dmamap_sync(sc->sc_dmat, bf->bf_dmamap, BUS_DMASYNC_PREWRITE);
4329 ath_tx_handoff(struct ath_softc *sc, struct ath_txq *txq, struct ath_buf *bf)
4331 struct ath_hal *ah = sc->sc_ah;
4332 struct ath_desc *ds, *ds0;
4336 * Fillin the remainder of the descriptor info.
4338 ds0 = ds = bf->bf_desc;
4339 for (i = 0; i < bf->bf_nseg; i++, ds++) {
4340 ds->ds_data = bf->bf_segs[i].ds_addr;
4341 if (i == bf->bf_nseg - 1)
4344 ds->ds_link = bf->bf_daddr + sizeof(*ds) * (i + 1);
4345 ath_hal_filltxdesc(ah, ds
4346 , bf->bf_segs[i].ds_len /* segment length */
4347 , i == 0 /* first segment */
4348 , i == bf->bf_nseg - 1 /* last segment */
4349 , ds0 /* first descriptor */
4351 DPRINTF(sc, ATH_DEBUG_XMIT,
4352 "%s: %d: %08x %08x %08x %08x %08x %08x\n",
4353 __func__, i, ds->ds_link, ds->ds_data,
4354 ds->ds_ctl0, ds->ds_ctl1, ds->ds_hw[0], ds->ds_hw[1]);
4357 * Insert the frame on the outbound list and pass it on
4358 * to the hardware. Multicast frames buffered for power
4359 * save stations and transmit from the CAB queue are stored
4360 * on a s/w only queue and loaded on to the CAB queue in
4361 * the SWBA handler since frames only go out on DTIM and
4362 * to avoid possible races.
4364 KASSERT((bf->bf_flags & ATH_BUF_BUSY) == 0,
4365 ("busy status 0x%x", bf->bf_flags));
4366 if (txq->axq_qnum != ATH_TXQ_SWQ) {
4367 #ifdef IEEE80211_SUPPORT_TDMA
4369 * Supporting transmit dma. If the queue is busy it is
4370 * impossible to determine if we've won the race against
4371 * the chipset checking the link field or not, so we don't
4372 * try. Instead we let the TX interrupt detect the case
4373 * and restart the transmitter.
4375 * If the queue is not busy we can start things rolling
4380 ATH_TXQ_INSERT_TAIL(txq, bf, bf_list);
4381 qbusy = ath_hal_txqenabled(ah, txq->axq_qnum);
4384 if (txq->axq_link != NULL) {
4386 * We had already started one previously but
4387 * not yet processed the TX interrupt. Don't
4388 * try to race a restart because we do not
4389 * know where it stopped, let the TX interrupt
4390 * restart us when it figures out where we
4394 *txq->axq_link = bf->bf_daddr;
4395 txq->axq_flags |= ATH_TXQ_PUTPENDING;
4398 * We are first in line, we can safely start
4402 ath_hal_puttxbuf(ah, txq->axq_qnum,
4407 * The queue is busy, go ahead and link us in but
4408 * do not try to start/restart the tx. We just
4409 * don't know whether it will pick up our link
4410 * or not and we don't want to double-xmit.
4412 if (txq->axq_link != NULL) {
4414 *txq->axq_link = bf->bf_daddr;
4416 txq->axq_flags |= ATH_TXQ_PUTPENDING;
4419 ath_hal_puttxbuf(ah, txq->axq_qnum,
4420 STAILQ_FIRST(&txq->axq_q)->bf_daddr);
4423 ATH_TXQ_INSERT_TAIL(txq, bf, bf_list);
4424 if (txq->axq_link == NULL) {
4425 ath_hal_puttxbuf(ah, txq->axq_qnum, bf->bf_daddr);
4426 DPRINTF(sc, ATH_DEBUG_XMIT,
4427 "%s: TXDP[%u] = %p (%p) depth %d\n",
4428 __func__, txq->axq_qnum,
4429 (caddr_t)bf->bf_daddr, bf->bf_desc,
4432 *txq->axq_link = bf->bf_daddr;
4433 DPRINTF(sc, ATH_DEBUG_XMIT,
4434 "%s: link[%u](%p)=%p (%p) depth %d\n", __func__,
4435 txq->axq_qnum, txq->axq_link,
4436 (caddr_t)bf->bf_daddr, bf->bf_desc, txq->axq_depth);
4438 #endif /* IEEE80211_SUPPORT_TDMA */
4439 txq->axq_link = &bf->bf_desc[bf->bf_nseg - 1].ds_link;
4440 ath_hal_txstart(ah, txq->axq_qnum);
4442 if (txq->axq_link != NULL) {
4443 struct ath_buf *last = ATH_TXQ_LAST(txq);
4444 struct ieee80211_frame *wh;
4446 /* mark previous frame */
4447 wh = mtod(last->bf_m, struct ieee80211_frame *);
4448 wh->i_fc[1] |= IEEE80211_FC1_MORE_DATA;
4449 bus_dmamap_sync(sc->sc_dmat, last->bf_dmamap,
4450 BUS_DMASYNC_PREWRITE);
4452 /* link descriptor */
4453 *txq->axq_link = bf->bf_daddr;
4455 ATH_TXQ_INSERT_TAIL(txq, bf, bf_list);
4456 txq->axq_link = &bf->bf_desc[bf->bf_nseg - 1].ds_link;
4461 ath_tx_start(struct ath_softc *sc, struct ieee80211_node *ni, struct ath_buf *bf,
4464 struct ieee80211vap *vap = ni->ni_vap;
4465 struct ath_vap *avp = ATH_VAP(vap);
4466 struct ath_hal *ah = sc->sc_ah;
4467 struct ifnet *ifp = sc->sc_ifp;
4468 struct ieee80211com *ic = ifp->if_l2com;
4469 const struct chanAccParams *cap = &ic->ic_wme.wme_chanParams;
4470 int error, iswep, ismcast, isfrag, ismrr;
4471 int keyix, hdrlen, pktlen, try0;
4472 u_int8_t rix, txrate, ctsrate;
4473 u_int8_t cix = 0xff; /* NB: silence compiler */
4474 struct ath_desc *ds;
4475 struct ath_txq *txq;
4476 struct ieee80211_frame *wh;
4477 u_int subtype, flags, ctsduration;
4479 const HAL_RATE_TABLE *rt;
4480 HAL_BOOL shortPreamble;
4481 struct ath_node *an;
4484 wh = mtod(m0, struct ieee80211_frame *);
4485 iswep = wh->i_fc[1] & IEEE80211_FC1_WEP;
4486 ismcast = IEEE80211_IS_MULTICAST(wh->i_addr1);
4487 isfrag = m0->m_flags & M_FRAG;
4488 hdrlen = ieee80211_anyhdrsize(wh);
4490 * Packet length must not include any
4491 * pad bytes; deduct them here.
4493 pktlen = m0->m_pkthdr.len - (hdrlen & 3);
4496 const struct ieee80211_cipher *cip;
4497 struct ieee80211_key *k;
4500 * Construct the 802.11 header+trailer for an encrypted
4501 * frame. The only reason this can fail is because of an
4502 * unknown or unsupported cipher/key type.
4504 k = ieee80211_crypto_encap(ni, m0);
4507 * This can happen when the key is yanked after the
4508 * frame was queued. Just discard the frame; the
4509 * 802.11 layer counts failures and provides
4510 * debugging/diagnostics.
4516 * Adjust the packet + header lengths for the crypto
4517 * additions and calculate the h/w key index. When
4518 * a s/w mic is done the frame will have had any mic
4519 * added to it prior to entry so m0->m_pkthdr.len will
4520 * account for it. Otherwise we need to add it to the
4524 hdrlen += cip->ic_header;
4525 pktlen += cip->ic_header + cip->ic_trailer;
4526 /* NB: frags always have any TKIP MIC done in s/w */
4527 if ((k->wk_flags & IEEE80211_KEY_SWMIC) == 0 && !isfrag)
4528 pktlen += cip->ic_miclen;
4529 keyix = k->wk_keyix;
4531 /* packet header may have moved, reset our local pointer */
4532 wh = mtod(m0, struct ieee80211_frame *);
4533 } else if (ni->ni_ucastkey.wk_cipher == &ieee80211_cipher_none) {
4535 * Use station key cache slot, if assigned.
4537 keyix = ni->ni_ucastkey.wk_keyix;
4538 if (keyix == IEEE80211_KEYIX_NONE)
4539 keyix = HAL_TXKEYIX_INVALID;
4541 keyix = HAL_TXKEYIX_INVALID;
4543 pktlen += IEEE80211_CRC_LEN;
4546 * Load the DMA map so any coalescing is done. This
4547 * also calculates the number of descriptors we need.
4549 error = ath_tx_dmasetup(sc, bf, m0);
4553 bf->bf_node = ni; /* NB: held reference */
4554 m0 = bf->bf_m; /* NB: may have changed */
4555 wh = mtod(m0, struct ieee80211_frame *);
4557 /* setup descriptors */
4559 rt = sc->sc_currates;
4560 KASSERT(rt != NULL, ("no rate table, mode %u", sc->sc_curmode));
4563 * NB: the 802.11 layer marks whether or not we should
4564 * use short preamble based on the current mode and
4565 * negotiated parameters.
4567 if ((ic->ic_flags & IEEE80211_F_SHPREAMBLE) &&
4568 (ni->ni_capinfo & IEEE80211_CAPINFO_SHORT_PREAMBLE)) {
4569 shortPreamble = AH_TRUE;
4570 sc->sc_stats.ast_tx_shortpre++;
4572 shortPreamble = AH_FALSE;
4576 flags = HAL_TXDESC_CLRDMASK; /* XXX needed for crypto errs */
4577 ismrr = 0; /* default no multi-rate retry*/
4578 pri = M_WME_GETAC(m0); /* honor classification */
4579 /* XXX use txparams instead of fixed values */
4581 * Calculate Atheros packet type from IEEE80211 packet header,
4582 * setup for rate calculations, and select h/w transmit queue.
4584 switch (wh->i_fc[0] & IEEE80211_FC0_TYPE_MASK) {
4585 case IEEE80211_FC0_TYPE_MGT:
4586 subtype = wh->i_fc[0] & IEEE80211_FC0_SUBTYPE_MASK;
4587 if (subtype == IEEE80211_FC0_SUBTYPE_BEACON)
4588 atype = HAL_PKT_TYPE_BEACON;
4589 else if (subtype == IEEE80211_FC0_SUBTYPE_PROBE_RESP)
4590 atype = HAL_PKT_TYPE_PROBE_RESP;
4591 else if (subtype == IEEE80211_FC0_SUBTYPE_ATIM)
4592 atype = HAL_PKT_TYPE_ATIM;
4594 atype = HAL_PKT_TYPE_NORMAL; /* XXX */
4595 rix = an->an_mgmtrix;
4596 txrate = rt->info[rix].rateCode;
4598 txrate |= rt->info[rix].shortPreamble;
4599 try0 = ATH_TXMGTTRY;
4600 flags |= HAL_TXDESC_INTREQ; /* force interrupt */
4602 case IEEE80211_FC0_TYPE_CTL:
4603 atype = HAL_PKT_TYPE_PSPOLL; /* stop setting of duration */
4604 rix = an->an_mgmtrix;
4605 txrate = rt->info[rix].rateCode;
4607 txrate |= rt->info[rix].shortPreamble;
4608 try0 = ATH_TXMGTTRY;
4609 flags |= HAL_TXDESC_INTREQ; /* force interrupt */
4611 case IEEE80211_FC0_TYPE_DATA:
4612 atype = HAL_PKT_TYPE_NORMAL; /* default */
4614 * Data frames: multicast frames go out at a fixed rate,
4615 * EAPOL frames use the mgmt frame rate; otherwise consult
4616 * the rate control module for the rate to use.
4619 rix = an->an_mcastrix;
4620 txrate = rt->info[rix].rateCode;
4622 txrate |= rt->info[rix].shortPreamble;
4624 } else if (m0->m_flags & M_EAPOL) {
4625 /* XXX? maybe always use long preamble? */
4626 rix = an->an_mgmtrix;
4627 txrate = rt->info[rix].rateCode;
4629 txrate |= rt->info[rix].shortPreamble;
4630 try0 = ATH_TXMAXTRY; /* XXX?too many? */
4632 ath_rate_findrate(sc, an, shortPreamble, pktlen,
4633 &rix, &try0, &txrate);
4634 sc->sc_txrix = rix; /* for LED blinking */
4635 sc->sc_lastdatarix = rix; /* for fast frames */
4636 if (try0 != ATH_TXMAXTRY)
4639 if (cap->cap_wmeParams[pri].wmep_noackPolicy)
4640 flags |= HAL_TXDESC_NOACK;
4643 if_printf(ifp, "bogus frame type 0x%x (%s)\n",
4644 wh->i_fc[0] & IEEE80211_FC0_TYPE_MASK, __func__);
4649 txq = sc->sc_ac2q[pri];
4652 * When servicing one or more stations in power-save mode
4653 * (or) if there is some mcast data waiting on the mcast
4654 * queue (to prevent out of order delivery) multicast
4655 * frames must be buffered until after the beacon.
4657 if (ismcast && (vap->iv_ps_sta || avp->av_mcastq.axq_depth))
4658 txq = &avp->av_mcastq;
4661 * Calculate miscellaneous flags.
4664 flags |= HAL_TXDESC_NOACK; /* no ack on broad/multicast */
4665 } else if (pktlen > vap->iv_rtsthreshold &&
4666 (ni->ni_ath_flags & IEEE80211_NODE_FF) == 0) {
4667 flags |= HAL_TXDESC_RTSENA; /* RTS based on frame length */
4668 cix = rt->info[rix].controlRate;
4669 sc->sc_stats.ast_tx_rts++;
4671 if (flags & HAL_TXDESC_NOACK) /* NB: avoid double counting */
4672 sc->sc_stats.ast_tx_noack++;
4673 #ifdef IEEE80211_SUPPORT_TDMA
4674 if (sc->sc_tdma && (flags & HAL_TXDESC_NOACK) == 0) {
4675 DPRINTF(sc, ATH_DEBUG_TDMA,
4676 "%s: discard frame, ACK required w/ TDMA\n", __func__);
4677 sc->sc_stats.ast_tdma_ack++;
4684 * If 802.11g protection is enabled, determine whether
4685 * to use RTS/CTS or just CTS. Note that this is only
4686 * done for OFDM unicast frames.
4688 if ((ic->ic_flags & IEEE80211_F_USEPROT) &&
4689 rt->info[rix].phy == IEEE80211_T_OFDM &&
4690 (flags & HAL_TXDESC_NOACK) == 0) {
4691 /* XXX fragments must use CCK rates w/ protection */
4692 if (ic->ic_protmode == IEEE80211_PROT_RTSCTS)
4693 flags |= HAL_TXDESC_RTSENA;
4694 else if (ic->ic_protmode == IEEE80211_PROT_CTSONLY)
4695 flags |= HAL_TXDESC_CTSENA;
4698 * For frags it would be desirable to use the
4699 * highest CCK rate for RTS/CTS. But stations
4700 * farther away may detect it at a lower CCK rate
4701 * so use the configured protection rate instead
4704 cix = rt->info[sc->sc_protrix].controlRate;
4706 cix = rt->info[sc->sc_protrix].controlRate;
4707 sc->sc_stats.ast_tx_protect++;
4711 * Calculate duration. This logically belongs in the 802.11
4712 * layer but it lacks sufficient information to calculate it.
4714 if ((flags & HAL_TXDESC_NOACK) == 0 &&
4715 (wh->i_fc[0] & IEEE80211_FC0_TYPE_MASK) != IEEE80211_FC0_TYPE_CTL) {
4718 dur = rt->info[rix].spAckDuration;
4720 dur = rt->info[rix].lpAckDuration;
4721 if (wh->i_fc[1] & IEEE80211_FC1_MORE_FRAG) {
4722 dur += dur; /* additional SIFS+ACK */
4723 KASSERT(m0->m_nextpkt != NULL, ("no fragment"));
4725 * Include the size of next fragment so NAV is
4726 * updated properly. The last fragment uses only
4729 dur += ath_hal_computetxtime(ah, rt,
4730 m0->m_nextpkt->m_pkthdr.len,
4731 rix, shortPreamble);
4735 * Force hardware to use computed duration for next
4736 * fragment by disabling multi-rate retry which updates
4737 * duration based on the multi-rate duration table.
4740 try0 = ATH_TXMGTTRY; /* XXX? */
4742 *(u_int16_t *)wh->i_dur = htole16(dur);
4746 * Calculate RTS/CTS rate and duration if needed.
4749 if (flags & (HAL_TXDESC_RTSENA|HAL_TXDESC_CTSENA)) {
4751 * CTS transmit rate is derived from the transmit rate
4752 * by looking in the h/w rate table. We must also factor
4753 * in whether or not a short preamble is to be used.
4755 /* NB: cix is set above where RTS/CTS is enabled */
4756 KASSERT(cix != 0xff, ("cix not setup"));
4757 ctsrate = rt->info[cix].rateCode;
4759 * Compute the transmit duration based on the frame
4760 * size and the size of an ACK frame. We call into the
4761 * HAL to do the computation since it depends on the
4762 * characteristics of the actual PHY being used.
4764 * NB: CTS is assumed the same size as an ACK so we can
4765 * use the precalculated ACK durations.
4767 if (shortPreamble) {
4768 ctsrate |= rt->info[cix].shortPreamble;
4769 if (flags & HAL_TXDESC_RTSENA) /* SIFS + CTS */
4770 ctsduration += rt->info[cix].spAckDuration;
4771 ctsduration += ath_hal_computetxtime(ah,
4772 rt, pktlen, rix, AH_TRUE);
4773 if ((flags & HAL_TXDESC_NOACK) == 0) /* SIFS + ACK */
4774 ctsduration += rt->info[rix].spAckDuration;
4776 if (flags & HAL_TXDESC_RTSENA) /* SIFS + CTS */
4777 ctsduration += rt->info[cix].lpAckDuration;
4778 ctsduration += ath_hal_computetxtime(ah,
4779 rt, pktlen, rix, AH_FALSE);
4780 if ((flags & HAL_TXDESC_NOACK) == 0) /* SIFS + ACK */
4781 ctsduration += rt->info[rix].lpAckDuration;
4784 * Must disable multi-rate retry when using RTS/CTS.
4787 try0 = ATH_TXMGTTRY; /* XXX */
4792 * At this point we are committed to sending the frame
4793 * and we don't need to look at m_nextpkt; clear it in
4794 * case this frame is part of frag chain.
4796 m0->m_nextpkt = NULL;
4798 if (IFF_DUMPPKTS(sc, ATH_DEBUG_XMIT))
4799 ieee80211_dump_pkt(ic, mtod(m0, const uint8_t *), m0->m_len,
4800 sc->sc_hwmap[rix].ieeerate, -1);
4802 if (ieee80211_radiotap_active_vap(vap)) {
4803 u_int64_t tsf = ath_hal_gettsf64(ah);
4805 sc->sc_tx_th.wt_tsf = htole64(tsf);
4806 sc->sc_tx_th.wt_flags = sc->sc_hwmap[rix].txflags;
4808 sc->sc_tx_th.wt_flags |= IEEE80211_RADIOTAP_F_WEP;
4810 sc->sc_tx_th.wt_flags |= IEEE80211_RADIOTAP_F_FRAG;
4811 sc->sc_tx_th.wt_rate = sc->sc_hwmap[rix].ieeerate;
4812 sc->sc_tx_th.wt_txpower = ni->ni_txpower;
4813 sc->sc_tx_th.wt_antenna = sc->sc_txantenna;
4815 ieee80211_radiotap_tx(vap, m0);
4819 * Determine if a tx interrupt should be generated for
4820 * this descriptor. We take a tx interrupt to reap
4821 * descriptors when the h/w hits an EOL condition or
4822 * when the descriptor is specifically marked to generate
4823 * an interrupt. We periodically mark descriptors in this
4824 * way to insure timely replenishing of the supply needed
4825 * for sending frames. Defering interrupts reduces system
4826 * load and potentially allows more concurrent work to be
4827 * done but if done to aggressively can cause senders to
4830 * NB: use >= to deal with sc_txintrperiod changing
4831 * dynamically through sysctl.
4833 if (flags & HAL_TXDESC_INTREQ) {
4834 txq->axq_intrcnt = 0;
4835 } else if (++txq->axq_intrcnt >= sc->sc_txintrperiod) {
4836 flags |= HAL_TXDESC_INTREQ;
4837 txq->axq_intrcnt = 0;
4841 * Formulate first tx descriptor with tx controls.
4843 /* XXX check return value? */
4844 ath_hal_setuptxdesc(ah, ds
4845 , pktlen /* packet length */
4846 , hdrlen /* header length */
4847 , atype /* Atheros packet type */
4848 , ni->ni_txpower /* txpower */
4849 , txrate, try0 /* series 0 rate/tries */
4850 , keyix /* key cache index */
4851 , sc->sc_txantenna /* antenna mode */
4853 , ctsrate /* rts/cts rate */
4854 , ctsduration /* rts/cts duration */
4856 bf->bf_txflags = flags;
4858 * Setup the multi-rate retry state only when we're
4859 * going to use it. This assumes ath_hal_setuptxdesc
4860 * initializes the descriptors (so we don't have to)
4861 * when the hardware supports multi-rate retry and
4865 ath_rate_setupxtxdesc(sc, an, ds, shortPreamble, rix);
4867 ath_tx_handoff(sc, txq, bf);
4872 * Process completed xmit descriptors from the specified queue.
4875 ath_tx_processq(struct ath_softc *sc, struct ath_txq *txq)
4877 struct ath_hal *ah = sc->sc_ah;
4878 struct ifnet *ifp = sc->sc_ifp;
4879 struct ieee80211com *ic = ifp->if_l2com;
4880 struct ath_buf *bf, *last;
4881 struct ath_desc *ds, *ds0;
4882 struct ath_tx_status *ts;
4883 struct ieee80211_node *ni;
4884 struct ath_node *an;
4885 int sr, lr, pri, nacked;
4888 DPRINTF(sc, ATH_DEBUG_TX_PROC, "%s: tx queue %u head %p link %p\n",
4889 __func__, txq->axq_qnum,
4890 (caddr_t)(uintptr_t) ath_hal_gettxbuf(sc->sc_ah, txq->axq_qnum),
4896 txq->axq_intrcnt = 0; /* reset periodic desc intr count */
4897 bf = STAILQ_FIRST(&txq->axq_q);
4900 ds0 = &bf->bf_desc[0];
4901 ds = &bf->bf_desc[bf->bf_nseg - 1];
4902 ts = &bf->bf_status.ds_txstat;
4903 qbusy = ath_hal_txqenabled(ah, txq->axq_qnum);
4904 status = ath_hal_txprocdesc(ah, ds, ts);
4906 if (sc->sc_debug & ATH_DEBUG_XMIT_DESC)
4907 ath_printtxbuf(sc, bf, txq->axq_qnum, 0,
4910 if (status == HAL_EINPROGRESS) {
4911 #ifdef IEEE80211_SUPPORT_TDMA
4913 * If not done and the queue is not busy then the
4914 * transmitter raced the hardware on the link field
4915 * and we have to restart it.
4919 ath_hal_puttxbuf(ah, txq->axq_qnum,
4921 ath_hal_txstart(ah, txq->axq_qnum);
4926 ATH_TXQ_REMOVE_HEAD(txq, bf_list);
4927 #ifdef IEEE80211_SUPPORT_TDMA
4928 if (txq->axq_depth > 0) {
4930 * More frames follow. Mark the buffer busy
4931 * so it's not re-used while the hardware may
4932 * still re-read the link field in the descriptor.
4934 bf->bf_flags |= ATH_BUF_BUSY;
4937 if (txq->axq_depth == 0)
4939 txq->axq_link = NULL;
4944 if (ts->ts_status == 0) {
4945 u_int8_t txant = ts->ts_antenna;
4946 sc->sc_stats.ast_ant_tx[txant]++;
4947 sc->sc_ant_tx[txant]++;
4948 if (ts->ts_finaltsi != 0)
4949 sc->sc_stats.ast_tx_altrate++;
4950 pri = M_WME_GETAC(bf->bf_m);
4951 if (pri >= WME_AC_VO)
4952 ic->ic_wme.wme_hipri_traffic++;
4953 if ((bf->bf_txflags & HAL_TXDESC_NOACK) == 0)
4954 ni->ni_inact = ni->ni_inact_reload;
4956 if (ts->ts_status & HAL_TXERR_XRETRY)
4957 sc->sc_stats.ast_tx_xretries++;
4958 if (ts->ts_status & HAL_TXERR_FIFO)
4959 sc->sc_stats.ast_tx_fifoerr++;
4960 if (ts->ts_status & HAL_TXERR_FILT)
4961 sc->sc_stats.ast_tx_filtered++;
4962 if (bf->bf_m->m_flags & M_FF)
4963 sc->sc_stats.ast_ff_txerr++;
4965 sr = ts->ts_shortretry;
4966 lr = ts->ts_longretry;
4967 sc->sc_stats.ast_tx_shortretry += sr;
4968 sc->sc_stats.ast_tx_longretry += lr;
4970 * Hand the descriptor to the rate control algorithm.
4972 if ((ts->ts_status & HAL_TXERR_FILT) == 0 &&
4973 (bf->bf_txflags & HAL_TXDESC_NOACK) == 0) {
4975 * If frame was ack'd update statistics,
4976 * including the last rx time used to
4977 * workaround phantom bmiss interrupts.
4979 if (ts->ts_status == 0) {
4981 sc->sc_stats.ast_tx_rssi = ts->ts_rssi;
4982 ATH_RSSI_LPF(sc->sc_halstats.ns_avgtxrssi,
4985 ath_rate_tx_complete(sc, an, bf);
4988 * Do any tx complete callback. Note this must
4989 * be done before releasing the node reference.
4991 if (bf->bf_m->m_flags & M_TXCB)
4992 ieee80211_process_callback(ni, bf->bf_m,
4993 (bf->bf_txflags & HAL_TXDESC_NOACK) == 0 ?
4994 ts->ts_status : HAL_TXERR_XRETRY);
4995 ieee80211_free_node(ni);
4997 bus_dmamap_sync(sc->sc_dmat, bf->bf_dmamap,
4998 BUS_DMASYNC_POSTWRITE);
4999 bus_dmamap_unload(sc->sc_dmat, bf->bf_dmamap);
5005 last = STAILQ_LAST(&sc->sc_txbuf, ath_buf, bf_list);
5007 last->bf_flags &= ~ATH_BUF_BUSY;
5008 STAILQ_INSERT_TAIL(&sc->sc_txbuf, bf, bf_list);
5010 #ifdef IEEE80211_SUPPORT_SUPERG
5012 * Flush fast-frame staging queue when traffic slows.
5014 if (txq->axq_depth <= 1)
5015 ieee80211_ff_flush(ic, txq->axq_ac);
5021 txqactive(struct ath_hal *ah, int qnum)
5023 u_int32_t txqs = 1<<qnum;
5024 ath_hal_gettxintrtxqs(ah, &txqs);
5025 return (txqs & (1<<qnum));
5029 * Deferred processing of transmit interrupt; special-cased
5030 * for a single hardware transmit queue (e.g. 5210 and 5211).
5033 ath_tx_task_q0(void *arg, int npending)
5035 struct ath_softc *sc = arg;
5036 struct ifnet *ifp = sc->sc_ifp;
5038 wlan_serialize_enter();
5039 if (txqactive(sc->sc_ah, 0) && ath_tx_processq(sc, &sc->sc_txq[0]))
5040 sc->sc_lastrx = ath_hal_gettsf64(sc->sc_ah);
5041 if (txqactive(sc->sc_ah, sc->sc_cabq->axq_qnum))
5042 ath_tx_processq(sc, sc->sc_cabq);
5043 ifp->if_flags &= ~IFF_OACTIVE;
5044 sc->sc_wd_timer = 0;
5047 ath_led_event(sc, sc->sc_txrix);
5050 wlan_serialize_exit();
5054 * Deferred processing of transmit interrupt; special-cased
5055 * for four hardware queues, 0-3 (e.g. 5212 w/ WME support).
5058 ath_tx_task_q0123(void *arg, int npending)
5060 struct ath_softc *sc = arg;
5061 struct ifnet *ifp = sc->sc_ifp;
5064 wlan_serialize_enter();
5066 * Process each active queue.
5069 if (txqactive(sc->sc_ah, 0))
5070 nacked += ath_tx_processq(sc, &sc->sc_txq[0]);
5071 if (txqactive(sc->sc_ah, 1))
5072 nacked += ath_tx_processq(sc, &sc->sc_txq[1]);
5073 if (txqactive(sc->sc_ah, 2))
5074 nacked += ath_tx_processq(sc, &sc->sc_txq[2]);
5075 if (txqactive(sc->sc_ah, 3))
5076 nacked += ath_tx_processq(sc, &sc->sc_txq[3]);
5077 if (txqactive(sc->sc_ah, sc->sc_cabq->axq_qnum))
5078 ath_tx_processq(sc, sc->sc_cabq);
5080 sc->sc_lastrx = ath_hal_gettsf64(sc->sc_ah);
5082 ifp->if_flags &= ~IFF_OACTIVE;
5083 sc->sc_wd_timer = 0;
5086 ath_led_event(sc, sc->sc_txrix);
5089 wlan_serialize_exit();
5093 * Deferred processing of transmit interrupt.
5096 ath_tx_task(void *arg, int npending)
5098 struct ath_softc *sc = arg;
5099 struct ifnet *ifp = sc->sc_ifp;
5102 wlan_serialize_enter();
5105 * Process each active queue.
5108 for (i = 0; i < HAL_NUM_TX_QUEUES; i++) {
5109 if (ATH_TXQ_SETUP(sc, i) && txqactive(sc->sc_ah, i))
5110 nacked += ath_tx_processq(sc, &sc->sc_txq[i]);
5113 sc->sc_lastrx = ath_hal_gettsf64(sc->sc_ah);
5115 ifp->if_flags &= ~IFF_OACTIVE;
5116 sc->sc_wd_timer = 0;
5119 ath_led_event(sc, sc->sc_txrix);
5122 wlan_serialize_exit();
5126 ath_tx_draintxq(struct ath_softc *sc, struct ath_txq *txq)
5129 struct ath_hal *ah = sc->sc_ah;
5131 struct ieee80211_node *ni;
5136 * NB: this assumes output has been stopped and
5137 * we do not need to block ath_tx_proc
5139 bf = STAILQ_LAST(&sc->sc_txbuf, ath_buf, bf_list);
5141 bf->bf_flags &= ~ATH_BUF_BUSY;
5142 for (ix = 0;; ix++) {
5143 bf = STAILQ_FIRST(&txq->axq_q);
5145 txq->axq_link = NULL;
5148 ATH_TXQ_REMOVE_HEAD(txq, bf_list);
5150 if (sc->sc_debug & ATH_DEBUG_RESET) {
5151 struct ieee80211com *ic = sc->sc_ifp->if_l2com;
5153 ath_printtxbuf(sc, bf, txq->axq_qnum, ix,
5154 ath_hal_txprocdesc(ah, bf->bf_desc,
5155 &bf->bf_status.ds_txstat) == HAL_OK);
5156 ieee80211_dump_pkt(ic, mtod(bf->bf_m, const uint8_t *),
5157 bf->bf_m->m_len, 0, -1);
5159 #endif /* ATH_DEBUG */
5160 bus_dmamap_unload(sc->sc_dmat, bf->bf_dmamap);
5165 * Do any callback and reclaim the node reference.
5167 if (bf->bf_m->m_flags & M_TXCB)
5168 ieee80211_process_callback(ni, bf->bf_m, -1);
5169 ieee80211_free_node(ni);
5173 bf->bf_flags &= ~ATH_BUF_BUSY;
5175 STAILQ_INSERT_TAIL(&sc->sc_txbuf, bf, bf_list);
5180 ath_tx_stopdma(struct ath_softc *sc, struct ath_txq *txq)
5182 struct ath_hal *ah = sc->sc_ah;
5184 DPRINTF(sc, ATH_DEBUG_RESET, "%s: tx queue [%u] %p, link %p\n",
5185 __func__, txq->axq_qnum,
5186 (caddr_t)(uintptr_t) ath_hal_gettxbuf(ah, txq->axq_qnum),
5188 (void) ath_hal_stoptxdma(ah, txq->axq_qnum);
5192 * Drain the transmit queues and reclaim resources.
5195 ath_draintxq(struct ath_softc *sc)
5197 struct ath_hal *ah = sc->sc_ah;
5198 struct ifnet *ifp = sc->sc_ifp;
5201 /* XXX return value */
5202 if (!sc->sc_invalid) {
5203 /* don't touch the hardware if marked invalid */
5204 DPRINTF(sc, ATH_DEBUG_RESET, "%s: tx queue [%u] %p, link %p\n",
5205 __func__, sc->sc_bhalq,
5206 (caddr_t)(uintptr_t) ath_hal_gettxbuf(ah, sc->sc_bhalq),
5208 (void) ath_hal_stoptxdma(ah, sc->sc_bhalq);
5209 for (i = 0; i < HAL_NUM_TX_QUEUES; i++)
5210 if (ATH_TXQ_SETUP(sc, i))
5211 ath_tx_stopdma(sc, &sc->sc_txq[i]);
5213 for (i = 0; i < HAL_NUM_TX_QUEUES; i++)
5214 if (ATH_TXQ_SETUP(sc, i))
5215 ath_tx_draintxq(sc, &sc->sc_txq[i]);
5217 if (sc->sc_debug & ATH_DEBUG_RESET) {
5218 struct ath_buf *bf = STAILQ_FIRST(&sc->sc_bbuf);
5219 if (bf != NULL && bf->bf_m != NULL) {
5220 ath_printtxbuf(sc, bf, sc->sc_bhalq, 0,
5221 ath_hal_txprocdesc(ah, bf->bf_desc,
5222 &bf->bf_status.ds_txstat) == HAL_OK);
5223 ieee80211_dump_pkt(ifp->if_l2com,
5224 mtod(bf->bf_m, const uint8_t *), bf->bf_m->m_len,
5228 #endif /* ATH_DEBUG */
5229 ifp->if_flags &= ~IFF_OACTIVE;
5230 sc->sc_wd_timer = 0;
5234 * Disable the receive h/w in preparation for a reset.
5237 ath_stoprecv(struct ath_softc *sc)
5239 #define PA2DESC(_sc, _pa) \
5240 ((struct ath_desc *)((caddr_t)(_sc)->sc_rxdma.dd_desc + \
5241 ((_pa) - (_sc)->sc_rxdma.dd_desc_paddr)))
5242 struct ath_hal *ah = sc->sc_ah;
5244 ath_hal_stoppcurecv(ah); /* disable PCU */
5245 ath_hal_setrxfilter(ah, 0); /* clear recv filter */
5246 ath_hal_stopdmarecv(ah); /* disable DMA engine */
5247 DELAY(3000); /* 3ms is long enough for 1 frame */
5249 if (sc->sc_debug & (ATH_DEBUG_RESET | ATH_DEBUG_FATAL)) {
5253 kprintf("%s: rx queue %p, link %p\n", __func__,
5254 (caddr_t)(uintptr_t) ath_hal_getrxbuf(ah), sc->sc_rxlink);
5256 STAILQ_FOREACH(bf, &sc->sc_rxbuf, bf_list) {
5257 struct ath_desc *ds = bf->bf_desc;
5258 struct ath_rx_status *rs = &bf->bf_status.ds_rxstat;
5259 HAL_STATUS status = ath_hal_rxprocdesc(ah, ds,
5260 bf->bf_daddr, PA2DESC(sc, ds->ds_link), rs);
5261 if (status == HAL_OK || (sc->sc_debug & ATH_DEBUG_FATAL))
5262 ath_printrxbuf(sc, bf, ix, status == HAL_OK);
5267 if (sc->sc_rxpending != NULL) {
5268 m_freem(sc->sc_rxpending);
5269 sc->sc_rxpending = NULL;
5271 sc->sc_rxlink = NULL; /* just in case */
5276 * Enable the receive h/w following a reset.
5279 ath_startrecv(struct ath_softc *sc)
5281 struct ath_hal *ah = sc->sc_ah;
5284 sc->sc_rxlink = NULL;
5285 sc->sc_rxpending = NULL;
5286 STAILQ_FOREACH(bf, &sc->sc_rxbuf, bf_list) {
5287 int error = ath_rxbuf_init(sc, bf);
5289 DPRINTF(sc, ATH_DEBUG_RECV,
5290 "%s: ath_rxbuf_init failed %d\n",
5296 bf = STAILQ_FIRST(&sc->sc_rxbuf);
5297 ath_hal_putrxbuf(ah, bf->bf_daddr);
5298 ath_hal_rxena(ah); /* enable recv descriptors */
5299 ath_mode_init(sc); /* set filters, etc. */
5300 ath_hal_startpcurecv(ah); /* re-enable PCU/DMA engine */
5305 * Update internal state after a channel change.
5308 ath_chan_change(struct ath_softc *sc, struct ieee80211_channel *chan)
5310 enum ieee80211_phymode mode;
5313 * Change channels and update the h/w rate map
5314 * if we're switching; e.g. 11a to 11b/g.
5316 mode = ieee80211_chan2mode(chan);
5317 if (mode != sc->sc_curmode)
5318 ath_setcurmode(sc, mode);
5319 sc->sc_curchan = chan;
5323 * Set/change channels. If the channel is really being changed,
5324 * it's done by reseting the chip. To accomplish this we must
5325 * first cleanup any pending DMA, then restart stuff after a la
5329 ath_chan_set(struct ath_softc *sc, struct ieee80211_channel *chan)
5331 struct ifnet *ifp = sc->sc_ifp;
5332 struct ieee80211com *ic = ifp->if_l2com;
5333 struct ath_hal *ah = sc->sc_ah;
5335 DPRINTF(sc, ATH_DEBUG_RESET, "%s: %u (%u MHz, flags 0x%x)\n",
5336 __func__, ieee80211_chan2ieee(ic, chan),
5337 chan->ic_freq, chan->ic_flags);
5338 if (chan != sc->sc_curchan) {
5341 * To switch channels clear any pending DMA operations;
5342 * wait long enough for the RX fifo to drain, reset the
5343 * hardware at the new frequency, and then re-enable
5344 * the relevant bits of the h/w.
5346 ath_hal_intrset(ah, 0); /* disable interrupts */
5347 ath_draintxq(sc); /* clear pending tx frames */
5348 ath_stoprecv(sc); /* turn off frame recv */
5349 if (!ath_hal_reset(ah, sc->sc_opmode, chan, AH_TRUE, &status)) {
5350 if_printf(ifp, "%s: unable to reset "
5351 "channel %u (%u MHz, flags 0x%x), hal status %u\n",
5352 __func__, ieee80211_chan2ieee(ic, chan),
5353 chan->ic_freq, chan->ic_flags, status);
5356 sc->sc_diversity = ath_hal_getdiversity(ah);
5359 * Re-enable rx framework.
5361 if (ath_startrecv(sc) != 0) {
5362 if_printf(ifp, "%s: unable to restart recv logic\n",
5368 * Change channels and update the h/w rate map
5369 * if we're switching; e.g. 11a to 11b/g.
5371 ath_chan_change(sc, chan);
5374 * Re-enable interrupts.
5376 ath_hal_intrset(ah, sc->sc_imask);
5382 * Periodically recalibrate the PHY to account
5383 * for temperature/environment changes.
5386 ath_calibrate_callout(void *arg)
5388 struct ath_softc *sc = arg;
5389 struct ath_hal *ah = sc->sc_ah;
5390 struct ifnet *ifp = sc->sc_ifp;
5391 struct ieee80211com *ic = ifp->if_l2com;
5392 HAL_BOOL longCal, isCalDone;
5395 wlan_serialize_enter();
5397 if (ic->ic_flags & IEEE80211_F_SCAN) /* defer, off channel */
5399 longCal = (ticks - sc->sc_lastlongcal >= ath_longcalinterval*hz);
5401 sc->sc_stats.ast_per_cal++;
5402 sc->sc_lastlongcal = ticks;
5403 if (ath_hal_getrfgain(ah) == HAL_RFGAIN_NEED_CHANGE) {
5405 * Rfgain is out of bounds, reset the chip
5406 * to load new gain values.
5408 DPRINTF(sc, ATH_DEBUG_CALIBRATE,
5409 "%s: rfgain change\n", __func__);
5410 sc->sc_stats.ast_per_rfgain++;
5414 * If this long cal is after an idle period, then
5415 * reset the data collection state so we start fresh.
5417 if (sc->sc_resetcal) {
5418 (void) ath_hal_calreset(ah, sc->sc_curchan);
5419 sc->sc_lastcalreset = ticks;
5420 sc->sc_resetcal = 0;
5423 if (ath_hal_calibrateN(ah, sc->sc_curchan, longCal, &isCalDone)) {
5426 * Calibrate noise floor data again in case of change.
5428 ath_hal_process_noisefloor(ah);
5431 DPRINTF(sc, ATH_DEBUG_ANY,
5432 "%s: calibration of channel %u failed\n",
5433 __func__, sc->sc_curchan->ic_freq);
5434 sc->sc_stats.ast_per_calfail++;
5439 * Use a shorter interval to potentially collect multiple
5440 * data samples required to complete calibration. Once
5441 * we're told the work is done we drop back to a longer
5442 * interval between requests. We're more aggressive doing
5443 * work when operating as an AP to improve operation right
5446 nextcal = (1000*ath_shortcalinterval)/hz;
5447 if (sc->sc_opmode != HAL_M_HOSTAP)
5450 nextcal = ath_longcalinterval*hz;
5451 if (sc->sc_lastcalreset == 0)
5452 sc->sc_lastcalreset = sc->sc_lastlongcal;
5453 else if (ticks - sc->sc_lastcalreset >= ath_resetcalinterval*hz)
5454 sc->sc_resetcal = 1; /* setup reset next trip */
5458 DPRINTF(sc, ATH_DEBUG_CALIBRATE, "%s: next +%u (%sisCalDone)\n",
5459 __func__, nextcal, isCalDone ? "" : "!");
5460 callout_reset(&sc->sc_cal_ch, nextcal,
5461 ath_calibrate_callout, sc);
5463 DPRINTF(sc, ATH_DEBUG_CALIBRATE, "%s: calibration disabled\n",
5465 /* NB: don't rearm timer */
5467 wlan_serialize_exit();
5471 ath_scan_start(struct ieee80211com *ic)
5473 struct ifnet *ifp = ic->ic_ifp;
5474 struct ath_softc *sc = ifp->if_softc;
5475 struct ath_hal *ah = sc->sc_ah;
5478 /* XXX calibration timer? */
5480 sc->sc_scanning = 1;
5481 sc->sc_syncbeacon = 0;
5482 rfilt = ath_calcrxfilter(sc);
5483 ath_hal_setrxfilter(ah, rfilt);
5484 ath_hal_setassocid(ah, ifp->if_broadcastaddr, 0);
5486 DPRINTF(sc, ATH_DEBUG_STATE, "%s: RX filter 0x%x bssid %6D aid 0\n",
5487 __func__, rfilt, ifp->if_broadcastaddr, ":");
5491 ath_scan_end(struct ieee80211com *ic)
5493 struct ifnet *ifp = ic->ic_ifp;
5494 struct ath_softc *sc = ifp->if_softc;
5495 struct ath_hal *ah = sc->sc_ah;
5498 sc->sc_scanning = 0;
5499 rfilt = ath_calcrxfilter(sc);
5500 ath_hal_setrxfilter(ah, rfilt);
5501 ath_hal_setassocid(ah, sc->sc_curbssid, sc->sc_curaid);
5503 ath_hal_process_noisefloor(ah);
5505 DPRINTF(sc, ATH_DEBUG_STATE, "%s: RX filter 0x%x bssid %6D aid 0x%x\n",
5506 __func__, rfilt, sc->sc_curbssid, ":",
5511 ath_set_channel(struct ieee80211com *ic)
5513 struct ifnet *ifp = ic->ic_ifp;
5514 struct ath_softc *sc = ifp->if_softc;
5516 (void) ath_chan_set(sc, ic->ic_curchan);
5518 * If we are returning to our bss channel then mark state
5519 * so the next recv'd beacon's tsf will be used to sync the
5520 * beacon timers. Note that since we only hear beacons in
5521 * sta/ibss mode this has no effect in other operating modes.
5523 if (!sc->sc_scanning && ic->ic_curchan == ic->ic_bsschan)
5524 sc->sc_syncbeacon = 1;
5528 * Walk the vap list and check if there any vap's in RUN state.
5531 ath_isanyrunningvaps(struct ieee80211vap *this)
5533 struct ieee80211com *ic = this->iv_ic;
5534 struct ieee80211vap *vap;
5536 TAILQ_FOREACH(vap, &ic->ic_vaps, iv_next) {
5537 if (vap != this && vap->iv_state >= IEEE80211_S_RUN)
5544 ath_newstate(struct ieee80211vap *vap, enum ieee80211_state nstate, int arg)
5546 struct ieee80211com *ic = vap->iv_ic;
5547 struct ath_softc *sc = ic->ic_ifp->if_softc;
5548 struct ath_vap *avp = ATH_VAP(vap);
5549 struct ath_hal *ah = sc->sc_ah;
5550 struct ieee80211_node *ni = NULL;
5551 int i, error, stamode;
5553 static const HAL_LED_STATE leds[] = {
5554 HAL_LED_INIT, /* IEEE80211_S_INIT */
5555 HAL_LED_SCAN, /* IEEE80211_S_SCAN */
5556 HAL_LED_AUTH, /* IEEE80211_S_AUTH */
5557 HAL_LED_ASSOC, /* IEEE80211_S_ASSOC */
5558 HAL_LED_RUN, /* IEEE80211_S_CAC */
5559 HAL_LED_RUN, /* IEEE80211_S_RUN */
5560 HAL_LED_RUN, /* IEEE80211_S_CSA */
5561 HAL_LED_RUN, /* IEEE80211_S_SLEEP */
5564 DPRINTF(sc, ATH_DEBUG_STATE, "%s: %s -> %s\n", __func__,
5565 ieee80211_state_name[vap->iv_state],
5566 ieee80211_state_name[nstate]);
5568 callout_stop(&sc->sc_cal_ch);
5569 ath_hal_setledstate(ah, leds[nstate]); /* set LED */
5571 if (nstate == IEEE80211_S_SCAN) {
5573 * Scanning: turn off beacon miss and don't beacon.
5574 * Mark beacon state so when we reach RUN state we'll
5575 * [re]setup beacons. Unblock the task q thread so
5576 * deferred interrupt processing is done.
5579 sc->sc_imask &~ (HAL_INT_SWBA | HAL_INT_BMISS));
5580 sc->sc_imask &= ~(HAL_INT_SWBA | HAL_INT_BMISS);
5582 taskqueue_unblock(sc->sc_tq);
5586 rfilt = ath_calcrxfilter(sc);
5587 stamode = (vap->iv_opmode == IEEE80211_M_STA ||
5588 vap->iv_opmode == IEEE80211_M_AHDEMO ||
5589 vap->iv_opmode == IEEE80211_M_IBSS);
5590 if (stamode && nstate == IEEE80211_S_RUN) {
5591 sc->sc_curaid = ni->ni_associd;
5592 IEEE80211_ADDR_COPY(sc->sc_curbssid, ni->ni_bssid);
5593 ath_hal_setassocid(ah, sc->sc_curbssid, sc->sc_curaid);
5595 DPRINTF(sc, ATH_DEBUG_STATE, "%s: RX filter 0x%x bssid %6D aid 0x%x\n",
5596 __func__, rfilt, sc->sc_curbssid, ":", sc->sc_curaid);
5597 ath_hal_setrxfilter(ah, rfilt);
5599 /* XXX is this to restore keycache on resume? */
5600 if (vap->iv_opmode != IEEE80211_M_STA &&
5601 (vap->iv_flags & IEEE80211_F_PRIVACY)) {
5602 for (i = 0; i < IEEE80211_WEP_NKID; i++)
5603 if (ath_hal_keyisvalid(ah, i))
5604 ath_hal_keysetmac(ah, i, ni->ni_bssid);
5608 * Invoke the parent method to do net80211 work.
5610 error = avp->av_newstate(vap, nstate, arg);
5614 if (nstate == IEEE80211_S_RUN) {
5615 /* NB: collect bss node again, it may have changed */
5618 DPRINTF(sc, ATH_DEBUG_STATE,
5619 "%s(RUN): iv_flags 0x%08x bintvl %d bssid %6D "
5620 "capinfo 0x%04x chan %d\n", __func__,
5621 vap->iv_flags, ni->ni_intval, ni->ni_bssid, ":",
5622 ni->ni_capinfo, ieee80211_chan2ieee(ic, ic->ic_curchan));
5624 switch (vap->iv_opmode) {
5625 #ifdef IEEE80211_SUPPORT_TDMA
5626 case IEEE80211_M_AHDEMO:
5627 if ((vap->iv_caps & IEEE80211_C_TDMA) == 0)
5631 case IEEE80211_M_HOSTAP:
5632 case IEEE80211_M_IBSS:
5633 case IEEE80211_M_MBSS:
5635 * Allocate and setup the beacon frame.
5637 * Stop any previous beacon DMA. This may be
5638 * necessary, for example, when an ibss merge
5639 * causes reconfiguration; there will be a state
5640 * transition from RUN->RUN that means we may
5641 * be called with beacon transmission active.
5643 ath_hal_stoptxdma(ah, sc->sc_bhalq);
5645 error = ath_beacon_alloc(sc, ni);
5649 * If joining an adhoc network defer beacon timer
5650 * configuration to the next beacon frame so we
5651 * have a current TSF to use. Otherwise we're
5652 * starting an ibss/bss so there's no need to delay;
5653 * if this is the first vap moving to RUN state, then
5654 * beacon state needs to be [re]configured.
5656 if (vap->iv_opmode == IEEE80211_M_IBSS &&
5657 ni->ni_tstamp.tsf != 0) {
5658 sc->sc_syncbeacon = 1;
5659 } else if (!sc->sc_beacons) {
5660 #ifdef IEEE80211_SUPPORT_TDMA
5661 if (vap->iv_caps & IEEE80211_C_TDMA)
5662 ath_tdma_config(sc, vap);
5665 ath_beacon_config(sc, vap);
5669 case IEEE80211_M_STA:
5671 * Defer beacon timer configuration to the next
5672 * beacon frame so we have a current TSF to use
5673 * (any TSF collected when scanning is likely old).
5675 sc->sc_syncbeacon = 1;
5677 case IEEE80211_M_MONITOR:
5679 * Monitor mode vaps have only INIT->RUN and RUN->RUN
5680 * transitions so we must re-enable interrupts here to
5681 * handle the case of a single monitor mode vap.
5683 ath_hal_intrset(ah, sc->sc_imask);
5685 case IEEE80211_M_WDS:
5691 * Let the hal process statistics collected during a
5692 * scan so it can provide calibrated noise floor data.
5694 ath_hal_process_noisefloor(ah);
5696 * Reset rssi stats; maybe not the best place...
5698 sc->sc_halstats.ns_avgbrssi = ATH_RSSI_DUMMY_MARKER;
5699 sc->sc_halstats.ns_avgrssi = ATH_RSSI_DUMMY_MARKER;
5700 sc->sc_halstats.ns_avgtxrssi = ATH_RSSI_DUMMY_MARKER;
5702 * Finally, start any timers and the task q thread
5703 * (in case we didn't go through SCAN state).
5705 if (ath_longcalinterval != 0) {
5706 /* start periodic recalibration timer */
5707 callout_reset(&sc->sc_cal_ch, 1,
5708 ath_calibrate_callout, sc);
5710 DPRINTF(sc, ATH_DEBUG_CALIBRATE,
5711 "%s: calibration disabled\n", __func__);
5713 taskqueue_unblock(sc->sc_tq);
5714 } else if (nstate == IEEE80211_S_INIT) {
5716 * If there are no vaps left in RUN state then
5717 * shutdown host/driver operation:
5718 * o disable interrupts
5719 * o disable the task queue thread
5720 * o mark beacon processing as stopped
5722 if (!ath_isanyrunningvaps(vap)) {
5723 sc->sc_imask &= ~(HAL_INT_SWBA | HAL_INT_BMISS);
5724 /* disable interrupts */
5725 ath_hal_intrset(ah, sc->sc_imask &~ HAL_INT_GLOBAL);
5726 taskqueue_block(sc->sc_tq);
5729 #ifdef IEEE80211_SUPPORT_TDMA
5730 ath_hal_setcca(ah, AH_TRUE);
5738 * Allocate a key cache slot to the station so we can
5739 * setup a mapping from key index to node. The key cache
5740 * slot is needed for managing antenna state and for
5741 * compression when stations do not use crypto. We do
5742 * it uniliaterally here; if crypto is employed this slot
5743 * will be reassigned.
5746 ath_setup_stationkey(struct ieee80211_node *ni)
5748 struct ieee80211vap *vap = ni->ni_vap;
5749 struct ath_softc *sc = vap->iv_ic->ic_ifp->if_softc;
5750 ieee80211_keyix keyix, rxkeyix;
5752 if (!ath_key_alloc(vap, &ni->ni_ucastkey, &keyix, &rxkeyix)) {
5754 * Key cache is full; we'll fall back to doing
5755 * the more expensive lookup in software. Note
5756 * this also means no h/w compression.
5758 /* XXX msg+statistic */
5761 ni->ni_ucastkey.wk_keyix = keyix;
5762 ni->ni_ucastkey.wk_rxkeyix = rxkeyix;
5763 /* NB: must mark device key to get called back on delete */
5764 ni->ni_ucastkey.wk_flags |= IEEE80211_KEY_DEVKEY;
5765 IEEE80211_ADDR_COPY(ni->ni_ucastkey.wk_macaddr, ni->ni_macaddr);
5766 /* NB: this will create a pass-thru key entry */
5767 ath_keyset(sc, &ni->ni_ucastkey, vap->iv_bss);
5772 * Setup driver-specific state for a newly associated node.
5773 * Note that we're called also on a re-associate, the isnew
5774 * param tells us if this is the first time or not.
5777 ath_newassoc(struct ieee80211_node *ni, int isnew)
5779 struct ath_node *an = ATH_NODE(ni);
5780 struct ieee80211vap *vap = ni->ni_vap;
5781 struct ath_softc *sc = vap->iv_ic->ic_ifp->if_softc;
5782 const struct ieee80211_txparam *tp = ni->ni_txparms;
5784 an->an_mcastrix = ath_tx_findrix(sc, tp->mcastrate);
5785 an->an_mgmtrix = ath_tx_findrix(sc, tp->mgmtrate);
5787 ath_rate_newassoc(sc, an, isnew);
5789 (vap->iv_flags & IEEE80211_F_PRIVACY) == 0 && sc->sc_hasclrkey &&
5790 ni->ni_ucastkey.wk_keyix == IEEE80211_KEYIX_NONE)
5791 ath_setup_stationkey(ni);
5795 ath_setregdomain(struct ieee80211com *ic, struct ieee80211_regdomain *reg,
5796 int nchans, struct ieee80211_channel chans[])
5798 struct ath_softc *sc = ic->ic_ifp->if_softc;
5799 struct ath_hal *ah = sc->sc_ah;
5802 DPRINTF(sc, ATH_DEBUG_REGDOMAIN,
5803 "%s: rd %u cc %u location %c%s\n",
5804 __func__, reg->regdomain, reg->country, reg->location,
5805 reg->ecm ? " ecm" : "");
5807 status = ath_hal_set_channels(ah, chans, nchans,
5808 reg->country, reg->regdomain);
5809 if (status != HAL_OK) {
5810 DPRINTF(sc, ATH_DEBUG_REGDOMAIN, "%s: failed, status %u\n",
5812 return EINVAL; /* XXX */
5818 ath_getradiocaps(struct ieee80211com *ic,
5819 int maxchans, int *nchans, struct ieee80211_channel chans[])
5821 struct ath_softc *sc = ic->ic_ifp->if_softc;
5822 struct ath_hal *ah = sc->sc_ah;
5824 DPRINTF(sc, ATH_DEBUG_REGDOMAIN, "%s: use rd %u cc %d\n",
5825 __func__, SKU_DEBUG, CTRY_DEFAULT);
5827 /* XXX check return */
5828 (void) ath_hal_getchannels(ah, chans, maxchans, nchans,
5829 HAL_MODE_ALL, CTRY_DEFAULT, SKU_DEBUG, AH_TRUE);
5834 ath_getchannels(struct ath_softc *sc)
5836 struct ifnet *ifp = sc->sc_ifp;
5837 struct ieee80211com *ic = ifp->if_l2com;
5838 struct ath_hal *ah = sc->sc_ah;
5842 * Collect channel set based on EEPROM contents.
5844 status = ath_hal_init_channels(ah, ic->ic_channels, IEEE80211_CHAN_MAX,
5845 &ic->ic_nchans, HAL_MODE_ALL, CTRY_DEFAULT, SKU_NONE, AH_TRUE);
5846 if (status != HAL_OK) {
5847 if_printf(ifp, "%s: unable to collect channel list from hal, "
5848 "status %d\n", __func__, status);
5851 (void) ath_hal_getregdomain(ah, &sc->sc_eerd);
5852 ath_hal_getcountrycode(ah, &sc->sc_eecc); /* NB: cannot fail */
5853 /* XXX map Atheros sku's to net80211 SKU's */
5854 /* XXX net80211 types too small */
5855 ic->ic_regdomain.regdomain = (uint16_t) sc->sc_eerd;
5856 ic->ic_regdomain.country = (uint16_t) sc->sc_eecc;
5857 ic->ic_regdomain.isocc[0] = ' '; /* XXX don't know */
5858 ic->ic_regdomain.isocc[1] = ' ';
5860 ic->ic_regdomain.ecm = 1;
5861 ic->ic_regdomain.location = 'I';
5863 DPRINTF(sc, ATH_DEBUG_REGDOMAIN,
5864 "%s: eeprom rd %u cc %u (mapped rd %u cc %u) location %c%s\n",
5865 __func__, sc->sc_eerd, sc->sc_eecc,
5866 ic->ic_regdomain.regdomain, ic->ic_regdomain.country,
5867 ic->ic_regdomain.location, ic->ic_regdomain.ecm ? " ecm" : "");
5872 ath_led_done_callout(void *arg)
5874 struct ath_softc *sc = arg;
5876 wlan_serialize_enter();
5877 sc->sc_blinking = 0;
5878 wlan_serialize_exit();
5882 * Turn the LED off: flip the pin and then set a timer so no
5883 * update will happen for the specified duration.
5886 ath_led_off_callout(void *arg)
5888 struct ath_softc *sc = arg;
5890 wlan_serialize_enter();
5891 ath_hal_gpioset(sc->sc_ah, sc->sc_ledpin, !sc->sc_ledon);
5892 callout_reset(&sc->sc_ledtimer, sc->sc_ledoff,
5893 ath_led_done_callout, sc);
5894 wlan_serialize_exit();
5898 * Blink the LED according to the specified on/off times.
5901 ath_led_blink(struct ath_softc *sc, int on, int off)
5903 DPRINTF(sc, ATH_DEBUG_LED, "%s: on %u off %u\n", __func__, on, off);
5904 ath_hal_gpioset(sc->sc_ah, sc->sc_ledpin, sc->sc_ledon);
5905 sc->sc_blinking = 1;
5906 sc->sc_ledoff = off;
5907 callout_reset(&sc->sc_ledtimer, on, ath_led_off_callout, sc);
5911 ath_led_event(struct ath_softc *sc, int rix)
5913 sc->sc_ledevent = ticks; /* time of last event */
5914 if (sc->sc_blinking) /* don't interrupt active blink */
5916 ath_led_blink(sc, sc->sc_hwmap[rix].ledon, sc->sc_hwmap[rix].ledoff);
5920 ath_rate_setup(struct ath_softc *sc, u_int mode)
5922 struct ath_hal *ah = sc->sc_ah;
5923 const HAL_RATE_TABLE *rt;
5926 case IEEE80211_MODE_11A:
5927 rt = ath_hal_getratetable(ah, HAL_MODE_11A);
5929 case IEEE80211_MODE_HALF:
5930 rt = ath_hal_getratetable(ah, HAL_MODE_11A_HALF_RATE);
5932 case IEEE80211_MODE_QUARTER:
5933 rt = ath_hal_getratetable(ah, HAL_MODE_11A_QUARTER_RATE);
5935 case IEEE80211_MODE_11B:
5936 rt = ath_hal_getratetable(ah, HAL_MODE_11B);
5938 case IEEE80211_MODE_11G:
5939 rt = ath_hal_getratetable(ah, HAL_MODE_11G);
5941 case IEEE80211_MODE_TURBO_A:
5942 rt = ath_hal_getratetable(ah, HAL_MODE_108A);
5944 case IEEE80211_MODE_TURBO_G:
5945 rt = ath_hal_getratetable(ah, HAL_MODE_108G);
5947 case IEEE80211_MODE_STURBO_A:
5948 rt = ath_hal_getratetable(ah, HAL_MODE_TURBO);
5950 case IEEE80211_MODE_11NA:
5951 rt = ath_hal_getratetable(ah, HAL_MODE_11NA_HT20);
5953 case IEEE80211_MODE_11NG:
5954 rt = ath_hal_getratetable(ah, HAL_MODE_11NG_HT20);
5957 DPRINTF(sc, ATH_DEBUG_ANY, "%s: invalid mode %u\n",
5961 sc->sc_rates[mode] = rt;
5962 return (rt != NULL);
5966 ath_setcurmode(struct ath_softc *sc, enum ieee80211_phymode mode)
5968 /* NB: on/off times from the Atheros NDIS driver, w/ permission */
5969 static const struct {
5970 u_int rate; /* tx/rx 802.11 rate */
5971 u_int16_t timeOn; /* LED on time (ms) */
5972 u_int16_t timeOff; /* LED off time (ms) */
5988 /* XXX half/quarter rates */
5990 const HAL_RATE_TABLE *rt;
5993 memset(sc->sc_rixmap, 0xff, sizeof(sc->sc_rixmap));
5994 rt = sc->sc_rates[mode];
5995 KASSERT(rt != NULL, ("no h/w rate set for phy mode %u", mode));
5996 for (i = 0; i < rt->rateCount; i++) {
5997 uint8_t ieeerate = rt->info[i].dot11Rate & IEEE80211_RATE_VAL;
5998 if (rt->info[i].phy != IEEE80211_T_HT)
5999 sc->sc_rixmap[ieeerate] = i;
6001 sc->sc_rixmap[ieeerate | IEEE80211_RATE_MCS] = i;
6003 memset(sc->sc_hwmap, 0, sizeof(sc->sc_hwmap));
6004 for (i = 0; i < NELEM(sc->sc_hwmap); i++) {
6005 if (i >= rt->rateCount) {
6006 sc->sc_hwmap[i].ledon = (500 * hz) / 1000;
6007 sc->sc_hwmap[i].ledoff = (130 * hz) / 1000;
6010 sc->sc_hwmap[i].ieeerate =
6011 rt->info[i].dot11Rate & IEEE80211_RATE_VAL;
6012 if (rt->info[i].phy == IEEE80211_T_HT)
6013 sc->sc_hwmap[i].ieeerate |= IEEE80211_RATE_MCS;
6014 sc->sc_hwmap[i].txflags = IEEE80211_RADIOTAP_F_DATAPAD;
6015 if (rt->info[i].shortPreamble ||
6016 rt->info[i].phy == IEEE80211_T_OFDM)
6017 sc->sc_hwmap[i].txflags |= IEEE80211_RADIOTAP_F_SHORTPRE;
6018 sc->sc_hwmap[i].rxflags = sc->sc_hwmap[i].txflags;
6019 for (j = 0; j < NELEM(blinkrates)-1; j++)
6020 if (blinkrates[j].rate == sc->sc_hwmap[i].ieeerate)
6022 /* NB: this uses the last entry if the rate isn't found */
6023 /* XXX beware of overlow */
6024 sc->sc_hwmap[i].ledon = (blinkrates[j].timeOn * hz) / 1000;
6025 sc->sc_hwmap[i].ledoff = (blinkrates[j].timeOff * hz) / 1000;
6027 sc->sc_currates = rt;
6028 sc->sc_curmode = mode;
6030 * All protection frames are transmited at 2Mb/s for
6031 * 11g, otherwise at 1Mb/s.
6033 if (mode == IEEE80211_MODE_11G)
6034 sc->sc_protrix = ath_tx_findrix(sc, 2*2);
6036 sc->sc_protrix = ath_tx_findrix(sc, 2*1);
6037 /* NB: caller is responsible for reseting rate control state */
6042 ath_printrxbuf(struct ath_softc *sc, const struct ath_buf *bf,
6045 const struct ath_rx_status *rs = &bf->bf_status.ds_rxstat;
6046 struct ath_hal *ah = sc->sc_ah;
6047 const struct ath_desc *ds;
6050 for (i = 0, ds = bf->bf_desc; i < bf->bf_nseg; i++, ds++) {
6051 kprintf("R[%2u] (DS.V:%p DS.P:%p) L:%08x D:%08x%s\n"
6052 " %08x %08x %08x %08x\n",
6053 ix, ds, (const struct ath_desc *)bf->bf_daddr + i,
6054 ds->ds_link, ds->ds_data,
6055 !done ? "" : (rs->rs_status == 0) ? " *" : " !",
6056 ds->ds_ctl0, ds->ds_ctl1,
6057 ds->ds_hw[0], ds->ds_hw[1]);
6058 if (ah->ah_magic == 0x20065416) {
6059 kprintf(" %08x %08x %08x %08x %08x %08x %08x\n",
6060 ds->ds_hw[2], ds->ds_hw[3], ds->ds_hw[4],
6061 ds->ds_hw[5], ds->ds_hw[6], ds->ds_hw[7],
6068 ath_printtxbuf(struct ath_softc *sc, const struct ath_buf *bf,
6069 u_int qnum, u_int ix, int done)
6071 const struct ath_tx_status *ts = &bf->bf_status.ds_txstat;
6072 struct ath_hal *ah = sc->sc_ah;
6073 const struct ath_desc *ds;
6076 kprintf("Q%u[%3u]", qnum, ix);
6077 for (i = 0, ds = bf->bf_desc; i < bf->bf_nseg; i++, ds++) {
6078 kprintf(" (DS.V:%p DS.P:%p) L:%08x D:%08x F:04%x%s\n"
6079 " %08x %08x %08x %08x %08x %08x\n",
6080 ds, (const struct ath_desc *)bf->bf_daddr + i,
6081 ds->ds_link, ds->ds_data, bf->bf_txflags,
6082 !done ? "" : (ts->ts_status == 0) ? " *" : " !",
6083 ds->ds_ctl0, ds->ds_ctl1,
6084 ds->ds_hw[0], ds->ds_hw[1], ds->ds_hw[2], ds->ds_hw[3]);
6085 if (ah->ah_magic == 0x20065416) {
6086 kprintf(" %08x %08x %08x %08x %08x %08x %08x %08x\n",
6087 ds->ds_hw[4], ds->ds_hw[5], ds->ds_hw[6],
6088 ds->ds_hw[7], ds->ds_hw[8], ds->ds_hw[9],
6089 ds->ds_hw[10],ds->ds_hw[11]);
6090 kprintf(" %08x %08x %08x %08x %08x %08x %08x %08x\n",
6091 ds->ds_hw[12],ds->ds_hw[13],ds->ds_hw[14],
6092 ds->ds_hw[15],ds->ds_hw[16],ds->ds_hw[17],
6093 ds->ds_hw[18], ds->ds_hw[19]);
6097 #endif /* ATH_DEBUG */
6100 ath_watchdog_callout(void *arg)
6102 struct ath_softc *sc = arg;
6104 wlan_serialize_enter();
6105 if (sc->sc_wd_timer != 0 && --sc->sc_wd_timer == 0) {
6106 struct ifnet *ifp = sc->sc_ifp;
6109 if (ath_hal_gethangstate(sc->sc_ah, 0xffff, &hangs) &&
6111 if_printf(ifp, "%s hang detected (0x%x)\n",
6112 hangs & 0xff ? "bb" : "mac", hangs);
6114 if_printf(ifp, "device timeout\n");
6117 sc->sc_stats.ast_watchdog++;
6119 callout_reset(&sc->sc_wd_ch, hz, ath_watchdog_callout, sc);
6120 wlan_serialize_exit();
6125 * Diagnostic interface to the HAL. This is used by various
6126 * tools to do things like retrieve register contents for
6127 * debugging. The mechanism is intentionally opaque so that
6128 * it can change frequently w/o concern for compatiblity.
6131 ath_ioctl_diag(struct ath_softc *sc, struct ath_diag *ad)
6133 struct ath_hal *ah = sc->sc_ah;
6134 u_int id = ad->ad_id & ATH_DIAG_ID;
6135 void *indata = NULL;
6136 void *outdata = NULL;
6137 u_int32_t insize = ad->ad_in_size;
6138 u_int32_t outsize = ad->ad_out_size;
6141 if (ad->ad_id & ATH_DIAG_IN) {
6145 indata = kmalloc(insize, M_TEMP, M_INTWAIT);
6146 error = copyin(ad->ad_in_data, indata, insize);
6150 if (ad->ad_id & ATH_DIAG_DYN) {
6152 * Allocate a buffer for the results (otherwise the HAL
6153 * returns a pointer to a buffer where we can read the
6154 * results). Note that we depend on the HAL leaving this
6155 * pointer for us to use below in reclaiming the buffer;
6156 * may want to be more defensive.
6158 outdata = kmalloc(outsize, M_TEMP, M_INTWAIT);
6160 if (ath_hal_getdiagstate(ah, id, indata, insize, &outdata, &outsize)) {
6161 if (outsize < ad->ad_out_size)
6162 ad->ad_out_size = outsize;
6163 if (outdata != NULL)
6164 error = copyout(outdata, ad->ad_out_data,
6170 if ((ad->ad_id & ATH_DIAG_IN) && indata != NULL)
6171 kfree(indata, M_TEMP);
6172 if ((ad->ad_id & ATH_DIAG_DYN) && outdata != NULL)
6173 kfree(outdata, M_TEMP);
6176 #endif /* ATH_DIAGAPI */
6179 ath_ioctl(struct ifnet *ifp, u_long cmd, caddr_t data, struct ucred *ucred)
6181 #define IS_RUNNING(ifp) \
6182 ((ifp->if_flags & IFF_UP) && (ifp->if_flags & IFF_RUNNING))
6183 struct ath_softc *sc = ifp->if_softc;
6184 struct ieee80211com *ic = ifp->if_l2com;
6185 struct ifreq *ifr = (struct ifreq *)data;
6186 const HAL_RATE_TABLE *rt;
6191 if (IS_RUNNING(ifp)) {
6193 * To avoid rescanning another access point,
6194 * do not call ath_init() here. Instead,
6195 * only reflect promisc mode settings.
6198 } else if (ifp->if_flags & IFF_UP) {
6200 * Beware of being called during attach/detach
6201 * to reset promiscuous mode. In that case we
6202 * will still be marked UP but not RUNNING.
6203 * However trying to re-init the interface
6204 * is the wrong thing to do as we've already
6205 * torn down much of our state. There's
6206 * probably a better way to deal with this.
6208 if (!sc->sc_invalid)
6209 ath_init(sc); /* XXX lose error */
6211 ath_stop_locked(ifp);
6213 /* XXX must wakeup in places like ath_vap_delete */
6214 if (!sc->sc_invalid)
6215 ath_hal_setpower(sc->sc_ah, HAL_PM_FULL_SLEEP);
6221 error = ifmedia_ioctl(ifp, ifr, &ic->ic_media, cmd);
6224 /* NB: embed these numbers to get a consistent view */
6225 sc->sc_stats.ast_tx_packets = ifp->if_opackets;
6226 sc->sc_stats.ast_rx_packets = ifp->if_ipackets;
6227 sc->sc_stats.ast_tx_rssi = ATH_RSSI(sc->sc_halstats.ns_avgtxrssi);
6228 sc->sc_stats.ast_rx_rssi = ATH_RSSI(sc->sc_halstats.ns_avgrssi);
6229 #ifdef IEEE80211_SUPPORT_TDMA
6230 sc->sc_stats.ast_tdma_tsfadjp = TDMA_AVG(sc->sc_avgtsfdeltap);
6231 sc->sc_stats.ast_tdma_tsfadjm = TDMA_AVG(sc->sc_avgtsfdeltam);
6233 rt = sc->sc_currates;
6235 sc->sc_stats.ast_tx_rate =
6236 rt->info[sc->sc_txrix].dot11Rate &~ IEEE80211_RATE_BASIC;
6237 return copyout(&sc->sc_stats,
6238 ifr->ifr_data, sizeof (sc->sc_stats));
6240 error = priv_check(curthread, PRIV_DRIVER);
6242 memset(&sc->sc_stats, 0, sizeof(sc->sc_stats));
6246 error = ath_ioctl_diag(sc, (struct ath_diag *) ifr);
6250 error = ether_ioctl(ifp, cmd, data);
6261 ath_sysctl_slottime(SYSCTL_HANDLER_ARGS)
6263 struct ath_softc *sc = arg1;
6267 wlan_serialize_enter();
6268 slottime = ath_hal_getslottime(sc->sc_ah);
6269 error = sysctl_handle_int(oidp, &slottime, 0, req);
6270 if (error == 0 && req->newptr) {
6271 if (!ath_hal_setslottime(sc->sc_ah, slottime))
6274 wlan_serialize_exit();
6279 ath_sysctl_acktimeout(SYSCTL_HANDLER_ARGS)
6281 struct ath_softc *sc = arg1;
6285 wlan_serialize_enter();
6286 acktimeout = ath_hal_getacktimeout(sc->sc_ah);
6287 error = sysctl_handle_int(oidp, &acktimeout, 0, req);
6288 if (error == 0 && req->newptr) {
6289 if (!ath_hal_setacktimeout(sc->sc_ah, acktimeout))
6292 wlan_serialize_exit();
6297 ath_sysctl_ctstimeout(SYSCTL_HANDLER_ARGS)
6299 struct ath_softc *sc = arg1;
6303 wlan_serialize_enter();
6304 ctstimeout = ath_hal_getctstimeout(sc->sc_ah);
6305 error = sysctl_handle_int(oidp, &ctstimeout, 0, req);
6306 if (error == 0 && req->newptr) {
6307 if (!ath_hal_setctstimeout(sc->sc_ah, ctstimeout))
6310 wlan_serialize_exit();
6315 ath_sysctl_softled(SYSCTL_HANDLER_ARGS)
6317 struct ath_softc *sc = arg1;
6318 int softled = sc->sc_softled;
6321 error = sysctl_handle_int(oidp, &softled, 0, req);
6322 if (error || !req->newptr)
6324 wlan_serialize_enter();
6325 softled = (softled != 0);
6326 if (softled != sc->sc_softled) {
6328 /* NB: handle any sc_ledpin change */
6329 ath_hal_gpioCfgOutput(sc->sc_ah, sc->sc_ledpin,
6330 HAL_GPIO_MUX_MAC_NETWORK_LED);
6331 ath_hal_gpioset(sc->sc_ah, sc->sc_ledpin,
6334 sc->sc_softled = softled;
6336 wlan_serialize_exit();
6341 ath_sysctl_ledpin(SYSCTL_HANDLER_ARGS)
6343 struct ath_softc *sc = arg1;
6344 int ledpin = sc->sc_ledpin;
6347 error = sysctl_handle_int(oidp, &ledpin, 0, req);
6348 if (error || !req->newptr)
6350 wlan_serialize_enter();
6351 if (ledpin != sc->sc_ledpin) {
6352 sc->sc_ledpin = ledpin;
6353 if (sc->sc_softled) {
6354 ath_hal_gpioCfgOutput(sc->sc_ah, sc->sc_ledpin,
6355 HAL_GPIO_MUX_MAC_NETWORK_LED);
6356 ath_hal_gpioset(sc->sc_ah, sc->sc_ledpin,
6360 wlan_serialize_exit();
6365 ath_sysctl_txantenna(SYSCTL_HANDLER_ARGS)
6367 struct ath_softc *sc = arg1;
6371 wlan_serialize_enter();
6372 txantenna = ath_hal_getantennaswitch(sc->sc_ah);
6373 error = sysctl_handle_int(oidp, &txantenna, 0, req);
6375 if (!error && req->newptr) {
6376 /* XXX assumes 2 antenna ports */
6377 if (txantenna < HAL_ANT_VARIABLE ||
6378 txantenna > HAL_ANT_FIXED_B) {
6381 ath_hal_setantennaswitch(sc->sc_ah, txantenna);
6383 * NB: with the switch locked this isn't meaningful,
6384 * but set it anyway so things like radiotap get
6385 * consistent info in their data.
6387 sc->sc_txantenna = txantenna;
6390 wlan_serialize_exit();
6395 ath_sysctl_rxantenna(SYSCTL_HANDLER_ARGS)
6397 struct ath_softc *sc = arg1;
6401 wlan_serialize_enter();
6402 defantenna = ath_hal_getdefantenna(sc->sc_ah);
6403 error = sysctl_handle_int(oidp, &defantenna, 0, req);
6404 if (error == 0 && req->newptr)
6405 ath_hal_setdefantenna(sc->sc_ah, defantenna);
6406 wlan_serialize_exit();
6411 ath_sysctl_diversity(SYSCTL_HANDLER_ARGS)
6413 struct ath_softc *sc = arg1;
6417 wlan_serialize_enter();
6418 diversity = ath_hal_getdiversity(sc->sc_ah);
6419 error = sysctl_handle_int(oidp, &diversity, 0, req);
6420 if (error == 0 && req->newptr) {
6421 if (!ath_hal_setdiversity(sc->sc_ah, diversity))
6424 sc->sc_diversity = diversity;
6426 wlan_serialize_exit();
6431 ath_sysctl_diag(SYSCTL_HANDLER_ARGS)
6433 struct ath_softc *sc = arg1;
6437 wlan_serialize_enter();
6438 if (!ath_hal_getdiag(sc->sc_ah, &diag)) {
6441 error = sysctl_handle_int(oidp, &diag, 0, req);
6442 if (error == 0 && req->newptr) {
6443 if (!ath_hal_setdiag(sc->sc_ah, diag))
6447 wlan_serialize_exit();
6452 ath_sysctl_tpscale(SYSCTL_HANDLER_ARGS)
6454 struct ath_softc *sc = arg1;
6455 struct ifnet *ifp = sc->sc_ifp;
6459 wlan_serialize_enter();
6460 (void)ath_hal_gettpscale(sc->sc_ah, &scale);
6461 error = sysctl_handle_int(oidp, &scale, 0, req);
6462 if (error == 0 && req->newptr) {
6463 if (!ath_hal_settpscale(sc->sc_ah, scale))
6465 else if (ifp->if_flags & IFF_RUNNING)
6466 error = ath_reset(ifp);
6468 wlan_serialize_exit();
6473 ath_sysctl_tpc(SYSCTL_HANDLER_ARGS)
6475 struct ath_softc *sc = arg1;
6479 wlan_serialize_enter();
6480 tpc = ath_hal_gettpc(sc->sc_ah);
6481 error = sysctl_handle_int(oidp, &tpc, 0, req);
6482 if (error == 0 && req->newptr) {
6483 if (!ath_hal_settpc(sc->sc_ah, tpc))
6486 wlan_serialize_exit();
6491 ath_sysctl_rfkill(SYSCTL_HANDLER_ARGS)
6493 struct ath_softc *sc = arg1;
6499 wlan_serialize_enter();
6502 rfkill = ath_hal_getrfkill(ah);
6504 error = sysctl_handle_int(oidp, &rfkill, 0, req);
6505 if (error == 0 && req->newptr) {
6506 if (rfkill != ath_hal_getrfkill(ah)) {
6507 if (!ath_hal_setrfkill(ah, rfkill))
6509 else if (ifp->if_flags & IFF_RUNNING)
6510 error = ath_reset(ifp);
6513 wlan_serialize_exit();
6518 ath_sysctl_rfsilent(SYSCTL_HANDLER_ARGS)
6520 struct ath_softc *sc = arg1;
6524 wlan_serialize_enter();
6525 (void)ath_hal_getrfsilent(sc->sc_ah, &rfsilent);
6526 error = sysctl_handle_int(oidp, &rfsilent, 0, req);
6527 if (error == 0 && req->newptr) {
6528 if (!ath_hal_setrfsilent(sc->sc_ah, rfsilent)) {
6531 sc->sc_rfsilentpin = rfsilent & 0x1c;
6532 sc->sc_rfsilentpol = (rfsilent & 0x2) != 0;
6535 wlan_serialize_exit();
6540 ath_sysctl_tpack(SYSCTL_HANDLER_ARGS)
6542 struct ath_softc *sc = arg1;
6546 wlan_serialize_enter();
6547 (void)ath_hal_gettpack(sc->sc_ah, &tpack);
6548 error = sysctl_handle_int(oidp, &tpack, 0, req);
6549 if (error == 0 && req->newptr) {
6550 if (!ath_hal_settpack(sc->sc_ah, tpack))
6553 wlan_serialize_exit();
6558 ath_sysctl_tpcts(SYSCTL_HANDLER_ARGS)
6560 struct ath_softc *sc = arg1;
6564 wlan_serialize_enter();
6565 (void)ath_hal_gettpcts(sc->sc_ah, &tpcts);
6566 error = sysctl_handle_int(oidp, &tpcts, 0, req);
6567 if (error == 0 && req->newptr) {
6568 if (!ath_hal_settpcts(sc->sc_ah, tpcts))
6571 wlan_serialize_exit();
6576 ath_sysctl_intmit(SYSCTL_HANDLER_ARGS)
6578 struct ath_softc *sc = arg1;
6581 wlan_serialize_enter();
6582 intmit = ath_hal_getintmit(sc->sc_ah);
6583 error = sysctl_handle_int(oidp, &intmit, 0, req);
6584 if (error == 0 && req->newptr) {
6585 if (!ath_hal_setintmit(sc->sc_ah, intmit))
6588 wlan_serialize_exit();
6592 #ifdef IEEE80211_SUPPORT_TDMA
6594 ath_sysctl_setcca(SYSCTL_HANDLER_ARGS)
6596 struct ath_softc *sc = arg1;
6599 wlan_serialize_enter();
6600 setcca = sc->sc_setcca;
6601 error = sysctl_handle_int(oidp, &setcca, 0, req);
6602 if (error == 0 && req->newptr)
6603 sc->sc_setcca = (setcca != 0);
6604 wlan_serialize_exit();
6607 #endif /* IEEE80211_SUPPORT_TDMA */
6610 ath_sysctlattach(struct ath_softc *sc)
6612 struct sysctl_ctx_list *ctx;
6613 struct sysctl_oid *tree;
6614 struct ath_hal *ah = sc->sc_ah;
6616 ctx = &sc->sc_sysctl_ctx;
6617 tree = sc->sc_sysctl_tree;
6619 device_printf(sc->sc_dev, "can't add sysctl node\n");
6623 SYSCTL_ADD_INT(ctx, SYSCTL_CHILDREN(tree), OID_AUTO,
6624 "countrycode", CTLFLAG_RD, &sc->sc_eecc, 0,
6625 "EEPROM country code");
6626 SYSCTL_ADD_INT(ctx, SYSCTL_CHILDREN(tree), OID_AUTO,
6627 "regdomain", CTLFLAG_RD, &sc->sc_eerd, 0,
6628 "EEPROM regdomain code");
6630 SYSCTL_ADD_INT(ctx, SYSCTL_CHILDREN(tree), OID_AUTO,
6631 "debug", CTLFLAG_RW, &sc->sc_debug, 0,
6632 "control debugging printfs");
6634 SYSCTL_ADD_PROC(ctx, SYSCTL_CHILDREN(tree), OID_AUTO,
6635 "slottime", CTLTYPE_INT | CTLFLAG_RW, sc, 0,
6636 ath_sysctl_slottime, "I", "802.11 slot time (us)");
6637 SYSCTL_ADD_PROC(ctx, SYSCTL_CHILDREN(tree), OID_AUTO,
6638 "acktimeout", CTLTYPE_INT | CTLFLAG_RW, sc, 0,
6639 ath_sysctl_acktimeout, "I", "802.11 ACK timeout (us)");
6640 SYSCTL_ADD_PROC(ctx, SYSCTL_CHILDREN(tree), OID_AUTO,
6641 "ctstimeout", CTLTYPE_INT | CTLFLAG_RW, sc, 0,
6642 ath_sysctl_ctstimeout, "I", "802.11 CTS timeout (us)");
6643 SYSCTL_ADD_PROC(ctx, SYSCTL_CHILDREN(tree), OID_AUTO,
6644 "softled", CTLTYPE_INT | CTLFLAG_RW, sc, 0,
6645 ath_sysctl_softled, "I", "enable/disable software LED support");
6646 SYSCTL_ADD_PROC(ctx, SYSCTL_CHILDREN(tree), OID_AUTO,
6647 "ledpin", CTLTYPE_INT | CTLFLAG_RW, sc, 0,
6648 ath_sysctl_ledpin, "I", "GPIO pin connected to LED");
6649 SYSCTL_ADD_INT(ctx, SYSCTL_CHILDREN(tree), OID_AUTO,
6650 "ledon", CTLFLAG_RW, &sc->sc_ledon, 0,
6651 "setting to turn LED on");
6652 SYSCTL_ADD_INT(ctx, SYSCTL_CHILDREN(tree), OID_AUTO,
6653 "ledidle", CTLFLAG_RW, &sc->sc_ledidle, 0,
6654 "idle time for inactivity LED (ticks)");
6655 SYSCTL_ADD_PROC(ctx, SYSCTL_CHILDREN(tree), OID_AUTO,
6656 "txantenna", CTLTYPE_INT | CTLFLAG_RW, sc, 0,
6657 ath_sysctl_txantenna, "I", "antenna switch");
6658 SYSCTL_ADD_PROC(ctx, SYSCTL_CHILDREN(tree), OID_AUTO,
6659 "rxantenna", CTLTYPE_INT | CTLFLAG_RW, sc, 0,
6660 ath_sysctl_rxantenna, "I", "default/rx antenna");
6661 if (ath_hal_hasdiversity(ah))
6662 SYSCTL_ADD_PROC(ctx, SYSCTL_CHILDREN(tree), OID_AUTO,
6663 "diversity", CTLTYPE_INT | CTLFLAG_RW, sc, 0,
6664 ath_sysctl_diversity, "I", "antenna diversity");
6665 sc->sc_txintrperiod = ATH_TXINTR_PERIOD;
6666 SYSCTL_ADD_INT(ctx, SYSCTL_CHILDREN(tree), OID_AUTO,
6667 "txintrperiod", CTLFLAG_RW, &sc->sc_txintrperiod, 0,
6668 "tx descriptor batching");
6669 SYSCTL_ADD_PROC(ctx, SYSCTL_CHILDREN(tree), OID_AUTO,
6670 "diag", CTLTYPE_INT | CTLFLAG_RW, sc, 0,
6671 ath_sysctl_diag, "I", "h/w diagnostic control");
6672 SYSCTL_ADD_PROC(ctx, SYSCTL_CHILDREN(tree), OID_AUTO,
6673 "tpscale", CTLTYPE_INT | CTLFLAG_RW, sc, 0,
6674 ath_sysctl_tpscale, "I", "tx power scaling");
6675 if (ath_hal_hastpc(ah)) {
6676 SYSCTL_ADD_PROC(ctx, SYSCTL_CHILDREN(tree), OID_AUTO,
6677 "tpc", CTLTYPE_INT | CTLFLAG_RW, sc, 0,
6678 ath_sysctl_tpc, "I", "enable/disable per-packet TPC");
6679 SYSCTL_ADD_PROC(ctx, SYSCTL_CHILDREN(tree), OID_AUTO,
6680 "tpack", CTLTYPE_INT | CTLFLAG_RW, sc, 0,
6681 ath_sysctl_tpack, "I", "tx power for ack frames");
6682 SYSCTL_ADD_PROC(ctx, SYSCTL_CHILDREN(tree), OID_AUTO,
6683 "tpcts", CTLTYPE_INT | CTLFLAG_RW, sc, 0,
6684 ath_sysctl_tpcts, "I", "tx power for cts frames");
6686 if (ath_hal_hasrfsilent(ah)) {
6687 SYSCTL_ADD_PROC(ctx, SYSCTL_CHILDREN(tree), OID_AUTO,
6688 "rfsilent", CTLTYPE_INT | CTLFLAG_RW, sc, 0,
6689 ath_sysctl_rfsilent, "I", "h/w RF silent config");
6690 SYSCTL_ADD_PROC(ctx, SYSCTL_CHILDREN(tree), OID_AUTO,
6691 "rfkill", CTLTYPE_INT | CTLFLAG_RW, sc, 0,
6692 ath_sysctl_rfkill, "I", "enable/disable RF kill switch");
6694 if (ath_hal_hasintmit(ah)) {
6695 SYSCTL_ADD_PROC(ctx, SYSCTL_CHILDREN(tree), OID_AUTO,
6696 "intmit", CTLTYPE_INT | CTLFLAG_RW, sc, 0,
6697 ath_sysctl_intmit, "I", "interference mitigation");
6699 sc->sc_monpass = HAL_RXERR_DECRYPT | HAL_RXERR_MIC;
6700 SYSCTL_ADD_INT(ctx, SYSCTL_CHILDREN(tree), OID_AUTO,
6701 "monpass", CTLFLAG_RW, &sc->sc_monpass, 0,
6702 "mask of error frames to pass when monitoring");
6703 #ifdef IEEE80211_SUPPORT_TDMA
6704 if (ath_hal_macversion(ah) > 0x78) {
6705 sc->sc_tdmadbaprep = 2;
6706 SYSCTL_ADD_INT(ctx, SYSCTL_CHILDREN(tree), OID_AUTO,
6707 "dbaprep", CTLFLAG_RW, &sc->sc_tdmadbaprep, 0,
6708 "TDMA DBA preparation time");
6709 sc->sc_tdmaswbaprep = 10;
6710 SYSCTL_ADD_INT(ctx, SYSCTL_CHILDREN(tree), OID_AUTO,
6711 "swbaprep", CTLFLAG_RW, &sc->sc_tdmaswbaprep, 0,
6712 "TDMA SWBA preparation time");
6713 SYSCTL_ADD_INT(ctx, SYSCTL_CHILDREN(tree), OID_AUTO,
6714 "guardtime", CTLFLAG_RW, &sc->sc_tdmaguard, 0,
6715 "TDMA slot guard time");
6716 SYSCTL_ADD_INT(ctx, SYSCTL_CHILDREN(tree), OID_AUTO,
6717 "superframe", CTLFLAG_RD, &sc->sc_tdmabintval, 0,
6718 "TDMA calculated super frame");
6719 SYSCTL_ADD_PROC(ctx, SYSCTL_CHILDREN(tree), OID_AUTO,
6720 "setcca", CTLTYPE_INT | CTLFLAG_RW, sc, 0,
6721 ath_sysctl_setcca, "I", "enable CCA control");
6727 ath_tx_raw_start(struct ath_softc *sc, struct ieee80211_node *ni,
6728 struct ath_buf *bf, struct mbuf *m0,
6729 const struct ieee80211_bpf_params *params)
6731 struct ifnet *ifp = sc->sc_ifp;
6732 struct ieee80211com *ic = ifp->if_l2com;
6733 struct ath_hal *ah = sc->sc_ah;
6734 struct ieee80211vap *vap = ni->ni_vap;
6735 int error, ismcast, ismrr;
6736 int keyix, hdrlen, pktlen, try0, txantenna;
6737 u_int8_t rix, cix, txrate, ctsrate, rate1, rate2, rate3;
6738 struct ieee80211_frame *wh;
6739 u_int flags, ctsduration;
6741 const HAL_RATE_TABLE *rt;
6742 struct ath_desc *ds;
6745 wh = mtod(m0, struct ieee80211_frame *);
6746 ismcast = IEEE80211_IS_MULTICAST(wh->i_addr1);
6747 hdrlen = ieee80211_anyhdrsize(wh);
6749 * Packet length must not include any
6750 * pad bytes; deduct them here.
6752 /* XXX honor IEEE80211_BPF_DATAPAD */
6753 pktlen = m0->m_pkthdr.len - (hdrlen & 3) + IEEE80211_CRC_LEN;
6755 if (params->ibp_flags & IEEE80211_BPF_CRYPTO) {
6756 const struct ieee80211_cipher *cip;
6757 struct ieee80211_key *k;
6760 * Construct the 802.11 header+trailer for an encrypted
6761 * frame. The only reason this can fail is because of an
6762 * unknown or unsupported cipher/key type.
6764 k = ieee80211_crypto_encap(ni, m0);
6767 * This can happen when the key is yanked after the
6768 * frame was queued. Just discard the frame; the
6769 * 802.11 layer counts failures and provides
6770 * debugging/diagnostics.
6776 * Adjust the packet + header lengths for the crypto
6777 * additions and calculate the h/w key index. When
6778 * a s/w mic is done the frame will have had any mic
6779 * added to it prior to entry so m0->m_pkthdr.len will
6780 * account for it. Otherwise we need to add it to the
6784 hdrlen += cip->ic_header;
6785 pktlen += cip->ic_header + cip->ic_trailer;
6786 /* NB: frags always have any TKIP MIC done in s/w */
6787 if ((k->wk_flags & IEEE80211_KEY_SWMIC) == 0)
6788 pktlen += cip->ic_miclen;
6789 keyix = k->wk_keyix;
6791 /* packet header may have moved, reset our local pointer */
6792 wh = mtod(m0, struct ieee80211_frame *);
6793 } else if (ni->ni_ucastkey.wk_cipher == &ieee80211_cipher_none) {
6795 * Use station key cache slot, if assigned.
6797 keyix = ni->ni_ucastkey.wk_keyix;
6798 if (keyix == IEEE80211_KEYIX_NONE)
6799 keyix = HAL_TXKEYIX_INVALID;
6801 keyix = HAL_TXKEYIX_INVALID;
6803 error = ath_tx_dmasetup(sc, bf, m0);
6806 m0 = bf->bf_m; /* NB: may have changed */
6807 wh = mtod(m0, struct ieee80211_frame *);
6808 bf->bf_node = ni; /* NB: held reference */
6810 flags = HAL_TXDESC_CLRDMASK; /* XXX needed for crypto errs */
6811 flags |= HAL_TXDESC_INTREQ; /* force interrupt */
6812 if (params->ibp_flags & IEEE80211_BPF_RTS)
6813 flags |= HAL_TXDESC_RTSENA;
6814 else if (params->ibp_flags & IEEE80211_BPF_CTS)
6815 flags |= HAL_TXDESC_CTSENA;
6816 /* XXX leave ismcast to injector? */
6817 if ((params->ibp_flags & IEEE80211_BPF_NOACK) || ismcast)
6818 flags |= HAL_TXDESC_NOACK;
6820 rt = sc->sc_currates;
6821 KASSERT(rt != NULL, ("no rate table, mode %u", sc->sc_curmode));
6822 rix = ath_tx_findrix(sc, params->ibp_rate0);
6823 txrate = rt->info[rix].rateCode;
6824 if (params->ibp_flags & IEEE80211_BPF_SHORTPRE)
6825 txrate |= rt->info[rix].shortPreamble;
6827 try0 = params->ibp_try0;
6828 ismrr = (params->ibp_try1 != 0);
6829 txantenna = params->ibp_pri >> 2;
6830 if (txantenna == 0) /* XXX? */
6831 txantenna = sc->sc_txantenna;
6833 if (flags & (HAL_TXDESC_CTSENA | HAL_TXDESC_RTSENA)) {
6834 cix = ath_tx_findrix(sc, params->ibp_ctsrate);
6835 ctsrate = rt->info[cix].rateCode;
6836 if (params->ibp_flags & IEEE80211_BPF_SHORTPRE) {
6837 ctsrate |= rt->info[cix].shortPreamble;
6838 if (flags & HAL_TXDESC_RTSENA) /* SIFS + CTS */
6839 ctsduration += rt->info[cix].spAckDuration;
6840 ctsduration += ath_hal_computetxtime(ah,
6841 rt, pktlen, rix, AH_TRUE);
6842 if ((flags & HAL_TXDESC_NOACK) == 0) /* SIFS + ACK */
6843 ctsduration += rt->info[rix].spAckDuration;
6845 if (flags & HAL_TXDESC_RTSENA) /* SIFS + CTS */
6846 ctsduration += rt->info[cix].lpAckDuration;
6847 ctsduration += ath_hal_computetxtime(ah,
6848 rt, pktlen, rix, AH_FALSE);
6849 if ((flags & HAL_TXDESC_NOACK) == 0) /* SIFS + ACK */
6850 ctsduration += rt->info[rix].lpAckDuration;
6852 ismrr = 0; /* XXX */
6855 pri = params->ibp_pri & 3;
6857 * NB: we mark all packets as type PSPOLL so the h/w won't
6858 * set the sequence number, duration, etc.
6860 atype = HAL_PKT_TYPE_PSPOLL;
6862 if (IFF_DUMPPKTS(sc, ATH_DEBUG_XMIT))
6863 ieee80211_dump_pkt(ic, mtod(m0, caddr_t), m0->m_len,
6864 sc->sc_hwmap[rix].ieeerate, -1);
6866 if (ieee80211_radiotap_active_vap(vap)) {
6867 u_int64_t tsf = ath_hal_gettsf64(ah);
6869 sc->sc_tx_th.wt_tsf = htole64(tsf);
6870 sc->sc_tx_th.wt_flags = sc->sc_hwmap[rix].txflags;
6871 if (wh->i_fc[1] & IEEE80211_FC1_WEP)
6872 sc->sc_tx_th.wt_flags |= IEEE80211_RADIOTAP_F_WEP;
6873 if (m0->m_flags & M_FRAG)
6874 sc->sc_tx_th.wt_flags |= IEEE80211_RADIOTAP_F_FRAG;
6875 sc->sc_tx_th.wt_rate = sc->sc_hwmap[rix].ieeerate;
6876 sc->sc_tx_th.wt_txpower = ni->ni_txpower;
6877 sc->sc_tx_th.wt_antenna = sc->sc_txantenna;
6879 ieee80211_radiotap_tx(vap, m0);
6883 * Formulate first tx descriptor with tx controls.
6886 /* XXX check return value? */
6887 ath_hal_setuptxdesc(ah, ds
6888 , pktlen /* packet length */
6889 , hdrlen /* header length */
6890 , atype /* Atheros packet type */
6891 , params->ibp_power /* txpower */
6892 , txrate, try0 /* series 0 rate/tries */
6893 , keyix /* key cache index */
6894 , txantenna /* antenna mode */
6896 , ctsrate /* rts/cts rate */
6897 , ctsduration /* rts/cts duration */
6899 bf->bf_txflags = flags;
6902 rix = ath_tx_findrix(sc, params->ibp_rate1);
6903 rate1 = rt->info[rix].rateCode;
6904 if (params->ibp_flags & IEEE80211_BPF_SHORTPRE)
6905 rate1 |= rt->info[rix].shortPreamble;
6906 if (params->ibp_try2) {
6907 rix = ath_tx_findrix(sc, params->ibp_rate2);
6908 rate2 = rt->info[rix].rateCode;
6909 if (params->ibp_flags & IEEE80211_BPF_SHORTPRE)
6910 rate2 |= rt->info[rix].shortPreamble;
6913 if (params->ibp_try3) {
6914 rix = ath_tx_findrix(sc, params->ibp_rate3);
6915 rate3 = rt->info[rix].rateCode;
6916 if (params->ibp_flags & IEEE80211_BPF_SHORTPRE)
6917 rate3 |= rt->info[rix].shortPreamble;
6920 ath_hal_setupxtxdesc(ah, ds
6921 , rate1, params->ibp_try1 /* series 1 */
6922 , rate2, params->ibp_try2 /* series 2 */
6923 , rate3, params->ibp_try3 /* series 3 */
6927 /* NB: no buffered multicast in power save support */
6928 ath_tx_handoff(sc, sc->sc_ac2q[pri], bf);
6933 ath_raw_xmit(struct ieee80211_node *ni, struct mbuf *m,
6934 const struct ieee80211_bpf_params *params)
6936 struct ieee80211com *ic = ni->ni_ic;
6937 struct ifnet *ifp = ic->ic_ifp;
6938 struct ath_softc *sc = ifp->if_softc;
6942 if ((ifp->if_flags & IFF_RUNNING) == 0 || sc->sc_invalid) {
6943 DPRINTF(sc, ATH_DEBUG_XMIT, "%s: discard frame, %s", __func__,
6944 (ifp->if_flags & IFF_RUNNING) == 0 ?
6945 "!running" : "invalid");
6951 * Grab a TX buffer and associated resources.
6953 bf = ath_getbuf(sc);
6955 sc->sc_stats.ast_tx_nobuf++;
6961 if (params == NULL) {
6963 * Legacy path; interpret frame contents to decide
6964 * precisely how to send the frame.
6966 if (ath_tx_start(sc, ni, bf, m)) {
6967 error = EIO; /* XXX */
6972 * Caller supplied explicit parameters to use in
6973 * sending the frame.
6975 if (ath_tx_raw_start(sc, ni, bf, m, params)) {
6976 error = EIO; /* XXX */
6980 sc->sc_wd_timer = 5;
6982 sc->sc_stats.ast_tx_raw++;
6986 STAILQ_INSERT_HEAD(&sc->sc_txbuf, bf, bf_list);
6989 sc->sc_stats.ast_tx_raw_fail++;
6990 ieee80211_free_node(ni);
6995 * Announce various information on device/driver attach.
6998 ath_announce(struct ath_softc *sc)
7000 struct ifnet *ifp = sc->sc_ifp;
7001 struct ath_hal *ah = sc->sc_ah;
7003 if_printf(ifp, "AR%s mac %d.%d RF%s phy %d.%d\n",
7004 ath_hal_mac_name(ah), ah->ah_macVersion, ah->ah_macRev,
7005 ath_hal_rf_name(ah), ah->ah_phyRev >> 4, ah->ah_phyRev & 0xf);
7008 for (i = 0; i <= WME_AC_VO; i++) {
7009 struct ath_txq *txq = sc->sc_ac2q[i];
7010 if_printf(ifp, "Use hw queue %u for %s traffic\n",
7011 txq->axq_qnum, ieee80211_wme_acnames[i]);
7013 if_printf(ifp, "Use hw queue %u for CAB traffic\n",
7014 sc->sc_cabq->axq_qnum);
7015 if_printf(ifp, "Use hw queue %u for beacons\n", sc->sc_bhalq);
7017 if (ath_rxbuf != ATH_RXBUF)
7018 if_printf(ifp, "using %u rx buffers\n", ath_rxbuf);
7019 if (ath_txbuf != ATH_TXBUF)
7020 if_printf(ifp, "using %u tx buffers\n", ath_txbuf);
7021 if (sc->sc_mcastkey && bootverbose)
7022 if_printf(ifp, "using multicast key search\n");
7025 #ifdef IEEE80211_SUPPORT_TDMA
7026 static __inline uint32_t
7027 ath_hal_getnexttbtt(struct ath_hal *ah)
7029 #define AR_TIMER0 0x8028
7030 return OS_REG_READ(ah, AR_TIMER0);
7033 static __inline void
7034 ath_hal_adjusttsf(struct ath_hal *ah, int32_t tsfdelta)
7036 /* XXX handle wrap/overflow */
7037 OS_REG_WRITE(ah, AR_TSF_L32, OS_REG_READ(ah, AR_TSF_L32) + tsfdelta);
7041 ath_tdma_settimers(struct ath_softc *sc, u_int32_t nexttbtt, u_int32_t bintval)
7043 struct ath_hal *ah = sc->sc_ah;
7044 HAL_BEACON_TIMERS bt;
7046 bt.bt_intval = bintval | HAL_BEACON_ENA;
7047 bt.bt_nexttbtt = nexttbtt;
7048 bt.bt_nextdba = (nexttbtt<<3) - sc->sc_tdmadbaprep;
7049 bt.bt_nextswba = (nexttbtt<<3) - sc->sc_tdmaswbaprep;
7050 bt.bt_nextatim = nexttbtt+1;
7051 ath_hal_beaconsettimers(ah, &bt);
7055 * Calculate the beacon interval. This is periodic in the
7056 * superframe for the bss. We assume each station is configured
7057 * identically wrt transmit rate so the guard time we calculate
7058 * above will be the same on all stations. Note we need to
7059 * factor in the xmit time because the hardware will schedule
7060 * a frame for transmit if the start of the frame is within
7061 * the burst time. When we get hardware that properly kills
7062 * frames in the PCU we can reduce/eliminate the guard time.
7064 * Roundup to 1024 is so we have 1 TU buffer in the guard time
7065 * to deal with the granularity of the nexttbtt timer. 11n MAC's
7066 * with 1us timer granularity should allow us to reduce/eliminate
7070 ath_tdma_bintvalsetup(struct ath_softc *sc,
7071 const struct ieee80211_tdma_state *tdma)
7073 /* copy from vap state (XXX check all vaps have same value?) */
7074 sc->sc_tdmaslotlen = tdma->tdma_slotlen;
7076 sc->sc_tdmabintval = roundup((sc->sc_tdmaslotlen+sc->sc_tdmaguard) *
7077 tdma->tdma_slotcnt, 1024);
7078 sc->sc_tdmabintval >>= 10; /* TSF -> TU */
7079 if (sc->sc_tdmabintval & 1)
7080 sc->sc_tdmabintval++;
7082 if (tdma->tdma_slot == 0) {
7084 * Only slot 0 beacons; other slots respond.
7086 sc->sc_imask |= HAL_INT_SWBA;
7087 sc->sc_tdmaswba = 0; /* beacon immediately */
7089 /* XXX all vaps must be slot 0 or slot !0 */
7090 sc->sc_imask &= ~HAL_INT_SWBA;
7095 * Max 802.11 overhead. This assumes no 4-address frames and
7096 * the encapsulation done by ieee80211_encap (llc). We also
7097 * include potential crypto overhead.
7099 #define IEEE80211_MAXOVERHEAD \
7100 (sizeof(struct ieee80211_qosframe) \
7101 + sizeof(struct llc) \
7102 + IEEE80211_ADDR_LEN \
7103 + IEEE80211_WEP_IVLEN \
7104 + IEEE80211_WEP_KIDLEN \
7105 + IEEE80211_WEP_CRCLEN \
7106 + IEEE80211_WEP_MICLEN \
7107 + IEEE80211_CRC_LEN)
7110 * Setup initially for tdma operation. Start the beacon
7111 * timers and enable SWBA if we are slot 0. Otherwise
7112 * we wait for slot 0 to arrive so we can sync up before
7113 * starting to transmit.
7116 ath_tdma_config(struct ath_softc *sc, struct ieee80211vap *vap)
7118 struct ath_hal *ah = sc->sc_ah;
7119 struct ifnet *ifp = sc->sc_ifp;
7120 struct ieee80211com *ic = ifp->if_l2com;
7121 const struct ieee80211_txparam *tp;
7122 const struct ieee80211_tdma_state *tdma = NULL;
7126 vap = TAILQ_FIRST(&ic->ic_vaps); /* XXX */
7128 if_printf(ifp, "%s: no vaps?\n", __func__);
7132 tp = vap->iv_bss->ni_txparms;
7134 * Calculate the guard time for each slot. This is the
7135 * time to send a maximal-size frame according to the
7136 * fixed/lowest transmit rate. Note that the interface
7137 * mtu does not include the 802.11 overhead so we must
7138 * tack that on (ath_hal_computetxtime includes the
7139 * preamble and plcp in it's calculation).
7141 tdma = vap->iv_tdma;
7142 if (tp->ucastrate != IEEE80211_FIXED_RATE_NONE)
7143 rix = ath_tx_findrix(sc, tp->ucastrate);
7145 rix = ath_tx_findrix(sc, tp->mcastrate);
7146 /* XXX short preamble assumed */
7147 sc->sc_tdmaguard = ath_hal_computetxtime(ah, sc->sc_currates,
7148 ifp->if_mtu + IEEE80211_MAXOVERHEAD, rix, AH_TRUE);
7150 ath_hal_intrset(ah, 0);
7152 ath_beaconq_config(sc); /* setup h/w beacon q */
7154 ath_hal_setcca(ah, AH_FALSE); /* disable CCA */
7155 ath_tdma_bintvalsetup(sc, tdma); /* calculate beacon interval */
7156 ath_tdma_settimers(sc, sc->sc_tdmabintval,
7157 sc->sc_tdmabintval | HAL_BEACON_RESET_TSF);
7158 sc->sc_syncbeacon = 0;
7160 sc->sc_avgtsfdeltap = TDMA_DUMMY_MARKER;
7161 sc->sc_avgtsfdeltam = TDMA_DUMMY_MARKER;
7163 ath_hal_intrset(ah, sc->sc_imask);
7165 DPRINTF(sc, ATH_DEBUG_TDMA, "%s: slot %u len %uus cnt %u "
7166 "bsched %u guard %uus bintval %u TU dba prep %u\n", __func__,
7167 tdma->tdma_slot, tdma->tdma_slotlen, tdma->tdma_slotcnt,
7168 tdma->tdma_bintval, sc->sc_tdmaguard, sc->sc_tdmabintval,
7169 sc->sc_tdmadbaprep);
7173 * Update tdma operation. Called from the 802.11 layer
7174 * when a beacon is received from the TDMA station operating
7175 * in the slot immediately preceding us in the bss. Use
7176 * the rx timestamp for the beacon frame to update our
7177 * beacon timers so we follow their schedule. Note that
7178 * by using the rx timestamp we implicitly include the
7179 * propagation delay in our schedule.
7182 ath_tdma_update(struct ieee80211_node *ni,
7183 const struct ieee80211_tdma_param *tdma, int changed)
7185 #define TSF_TO_TU(_h,_l) \
7186 ((((u_int32_t)(_h)) << 22) | (((u_int32_t)(_l)) >> 10))
7187 #define TU_TO_TSF(_tu) (((u_int64_t)(_tu)) << 10)
7188 struct ieee80211vap *vap = ni->ni_vap;
7189 struct ieee80211com *ic = ni->ni_ic;
7190 struct ath_softc *sc = ic->ic_ifp->if_softc;
7191 struct ath_hal *ah = sc->sc_ah;
7192 const HAL_RATE_TABLE *rt = sc->sc_currates;
7193 u_int64_t tsf, rstamp, nextslot;
7194 u_int32_t txtime, nextslottu, timer0;
7195 int32_t tudelta, tsfdelta;
7196 const struct ath_rx_status *rs;
7199 sc->sc_stats.ast_tdma_update++;
7202 * Check for and adopt configuration changes.
7205 const struct ieee80211_tdma_state *ts = vap->iv_tdma;
7207 ath_tdma_bintvalsetup(sc, ts);
7208 if (changed & TDMA_UPDATE_SLOTLEN)
7211 DPRINTF(sc, ATH_DEBUG_TDMA,
7212 "%s: adopt slot %u slotcnt %u slotlen %u us "
7213 "bintval %u TU\n", __func__,
7214 ts->tdma_slot, ts->tdma_slotcnt, ts->tdma_slotlen,
7215 sc->sc_tdmabintval);
7218 ath_hal_intrset(ah, sc->sc_imask);
7219 /* NB: beacon timers programmed below */
7222 /* extend rx timestamp to 64 bits */
7224 tsf = ath_hal_gettsf64(ah);
7225 rstamp = ath_extend_tsf(rs->rs_tstamp, tsf);
7227 * The rx timestamp is set by the hardware on completing
7228 * reception (at the point where the rx descriptor is DMA'd
7229 * to the host). To find the start of our next slot we
7230 * must adjust this time by the time required to send
7231 * the packet just received.
7233 rix = rt->rateCodeToIndex[rs->rs_rate];
7234 txtime = ath_hal_computetxtime(ah, rt, rs->rs_datalen, rix,
7235 rt->info[rix].shortPreamble);
7236 /* NB: << 9 is to cvt to TU and /2 */
7237 nextslot = (rstamp - txtime) + (sc->sc_tdmabintval << 9);
7238 nextslottu = TSF_TO_TU(nextslot>>32, nextslot) & HAL_BEACON_PERIOD;
7241 * TIMER0 is the h/w's idea of NextTBTT (in TU's). Convert
7242 * to usecs and calculate the difference between what the
7243 * other station thinks and what we have programmed. This
7244 * lets us figure how to adjust our timers to match. The
7245 * adjustments are done by pulling the TSF forward and possibly
7246 * rewriting the beacon timers.
7248 timer0 = ath_hal_getnexttbtt(ah);
7249 tsfdelta = (int32_t)((nextslot % TU_TO_TSF(HAL_BEACON_PERIOD+1)) - TU_TO_TSF(timer0));
7251 DPRINTF(sc, ATH_DEBUG_TDMA_TIMER,
7252 "tsfdelta %d avg +%d/-%d\n", tsfdelta,
7253 TDMA_AVG(sc->sc_avgtsfdeltap), TDMA_AVG(sc->sc_avgtsfdeltam));
7256 TDMA_SAMPLE(sc->sc_avgtsfdeltap, 0);
7257 TDMA_SAMPLE(sc->sc_avgtsfdeltam, -tsfdelta);
7258 tsfdelta = -tsfdelta % 1024;
7260 } else if (tsfdelta > 0) {
7261 TDMA_SAMPLE(sc->sc_avgtsfdeltap, tsfdelta);
7262 TDMA_SAMPLE(sc->sc_avgtsfdeltam, 0);
7263 tsfdelta = 1024 - (tsfdelta % 1024);
7266 TDMA_SAMPLE(sc->sc_avgtsfdeltap, 0);
7267 TDMA_SAMPLE(sc->sc_avgtsfdeltam, 0);
7269 tudelta = nextslottu - timer0;
7272 * Copy sender's timetstamp into tdma ie so they can
7273 * calculate roundtrip time. We submit a beacon frame
7274 * below after any timer adjustment. The frame goes out
7275 * at the next TBTT so the sender can calculate the
7276 * roundtrip by inspecting the tdma ie in our beacon frame.
7278 * NB: This tstamp is subtlely preserved when
7279 * IEEE80211_BEACON_TDMA is marked (e.g. when the
7280 * slot position changes) because ieee80211_add_tdma
7281 * skips over the data.
7283 memcpy(ATH_VAP(vap)->av_boff.bo_tdma +
7284 __offsetof(struct ieee80211_tdma_param, tdma_tstamp),
7285 &ni->ni_tstamp.data, 8);
7287 DPRINTF(sc, ATH_DEBUG_TDMA_TIMER,
7288 "tsf %llu nextslot %llu (%d, %d) nextslottu %u timer0 %u (%d)\n",
7289 (unsigned long long) tsf, (unsigned long long) nextslot,
7290 (int)(nextslot - tsf), tsfdelta,
7291 nextslottu, timer0, tudelta);
7294 * Adjust the beacon timers only when pulling them forward
7295 * or when going back by less than the beacon interval.
7296 * Negative jumps larger than the beacon interval seem to
7297 * cause the timers to stop and generally cause instability.
7298 * This basically filters out jumps due to missed beacons.
7300 if (tudelta != 0 && (tudelta > 0 || -tudelta < sc->sc_tdmabintval)) {
7301 ath_tdma_settimers(sc, nextslottu, sc->sc_tdmabintval);
7302 sc->sc_stats.ast_tdma_timers++;
7305 ath_hal_adjusttsf(ah, tsfdelta);
7306 sc->sc_stats.ast_tdma_tsf++;
7308 ath_tdma_beacon_send(sc, vap); /* prepare response */
7314 * Transmit a beacon frame at SWBA. Dynamic updates
7315 * to the frame contents are done as needed.
7318 ath_tdma_beacon_send(struct ath_softc *sc, struct ieee80211vap *vap)
7320 struct ath_hal *ah = sc->sc_ah;
7325 * Check if the previous beacon has gone out. If
7326 * not don't try to post another, skip this period
7327 * and wait for the next. Missed beacons indicate
7328 * a problem and should not occur. If we miss too
7329 * many consecutive beacons reset the device.
7331 if (ath_hal_numtxpending(ah, sc->sc_bhalq) != 0) {
7332 sc->sc_bmisscount++;
7333 DPRINTF(sc, ATH_DEBUG_BEACON,
7334 "%s: missed %u consecutive beacons\n",
7335 __func__, sc->sc_bmisscount);
7336 if (sc->sc_bmisscount >= ath_bstuck_threshold)
7337 taskqueue_enqueue(sc->sc_tq, &sc->sc_bstucktask);
7340 if (sc->sc_bmisscount != 0) {
7341 DPRINTF(sc, ATH_DEBUG_BEACON,
7342 "%s: resume beacon xmit after %u misses\n",
7343 __func__, sc->sc_bmisscount);
7344 sc->sc_bmisscount = 0;
7348 * Check recent per-antenna transmit statistics and flip
7349 * the default antenna if noticeably more frames went out
7350 * on the non-default antenna.
7351 * XXX assumes 2 anntenae
7353 if (!sc->sc_diversity) {
7354 otherant = sc->sc_defant & 1 ? 2 : 1;
7355 if (sc->sc_ant_tx[otherant] > sc->sc_ant_tx[sc->sc_defant] + 2)
7356 ath_setdefantenna(sc, otherant);
7357 sc->sc_ant_tx[1] = sc->sc_ant_tx[2] = 0;
7361 * Stop any current dma before messing with the beacon linkages.
7363 * This should never fail since we check above that no frames
7364 * are still pending on the queue.
7366 if (!ath_hal_stoptxdma(ah, sc->sc_bhalq)) {
7367 DPRINTF(sc, ATH_DEBUG_ANY,
7368 "%s: beacon queue %u did not stop?\n",
7369 __func__, sc->sc_bhalq);
7370 /* NB: the HAL still stops DMA, so proceed */
7372 bf = ath_beacon_generate(sc, vap);
7374 ath_hal_puttxbuf(ah, sc->sc_bhalq, bf->bf_daddr);
7375 ath_hal_txstart(ah, sc->sc_bhalq);
7377 sc->sc_stats.ast_be_xmit++; /* XXX per-vap? */
7380 * Record local TSF for our last send for use
7381 * in arbitrating slot collisions.
7383 vap->iv_bss->ni_tstamp.tsf = ath_hal_gettsf64(ah);
7385 device_printf(sc->sc_dev, "tdma beacon gen failed!\n");
7388 #endif /* IEEE80211_SUPPORT_TDMA */
7391 ath_sysctl_clearstats(SYSCTL_HANDLER_ARGS)
7393 struct ath_softc *sc = arg1;
7397 error = sysctl_handle_int(oidp, &val, 0, req);
7398 if (error || !req->newptr)
7401 return 0; /* Not clearing the stats is still valid */
7402 memset(&sc->sc_stats, 0, sizeof(sc->sc_stats));
7408 ath_sysctl_stats_attach(struct ath_softc *sc)
7410 struct sysctl_oid *tree;
7411 struct sysctl_ctx_list *ctx;
7412 struct sysctl_oid_list *child;
7414 ctx = &sc->sc_sysctl_ctx;
7415 tree = sc->sc_sysctl_tree;
7416 child = SYSCTL_CHILDREN(tree);
7418 /* Create "clear" node */
7419 SYSCTL_ADD_PROC(ctx, SYSCTL_CHILDREN(tree), OID_AUTO,
7420 "clear_stats", CTLTYPE_INT | CTLFLAG_RW, sc, 0,
7421 ath_sysctl_clearstats, "I", "clear stats");
7423 /* Create stats node */
7424 tree = SYSCTL_ADD_NODE(ctx, child, OID_AUTO, "stats", CTLFLAG_RD,
7425 NULL, "Statistics");
7426 child = SYSCTL_CHILDREN(tree);
7428 /* This was generated from if_athioctl.h */
7430 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_watchdog", CTLFLAG_RD,
7431 &sc->sc_stats.ast_watchdog, 0, "device reset by watchdog");
7432 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_hardware", CTLFLAG_RD,
7433 &sc->sc_stats.ast_hardware, 0, "fatal hardware error interrupts");
7434 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_bmiss", CTLFLAG_RD,
7435 &sc->sc_stats.ast_bmiss, 0, "beacon miss interrupts");
7436 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_bmiss_phantom", CTLFLAG_RD,
7437 &sc->sc_stats.ast_bmiss_phantom, 0, "beacon miss interrupts");
7438 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_bstuck", CTLFLAG_RD,
7439 &sc->sc_stats.ast_bstuck, 0, "beacon stuck interrupts");
7440 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_rxorn", CTLFLAG_RD,
7441 &sc->sc_stats.ast_rxorn, 0, "rx overrun interrupts");
7442 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_rxeol", CTLFLAG_RD,
7443 &sc->sc_stats.ast_rxeol, 0, "rx eol interrupts");
7444 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_txurn", CTLFLAG_RD,
7445 &sc->sc_stats.ast_txurn, 0, "tx underrun interrupts");
7446 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_mib", CTLFLAG_RD,
7447 &sc->sc_stats.ast_mib, 0, "mib interrupts");
7448 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_intrcoal", CTLFLAG_RD,
7449 &sc->sc_stats.ast_intrcoal, 0, "interrupts coalesced");
7450 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_tx_packets", CTLFLAG_RD,
7451 &sc->sc_stats.ast_tx_packets, 0, "packet sent on the interface");
7452 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_tx_mgmt", CTLFLAG_RD,
7453 &sc->sc_stats.ast_tx_mgmt, 0, "management frames transmitted");
7454 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_tx_discard", CTLFLAG_RD,
7455 &sc->sc_stats.ast_tx_discard, 0, "frames discarded prior to assoc");
7456 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_tx_qstop", CTLFLAG_RD,
7457 &sc->sc_stats.ast_tx_qstop, 0, "output stopped 'cuz no buffer");
7458 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_tx_encap", CTLFLAG_RD,
7459 &sc->sc_stats.ast_tx_encap, 0, "tx encapsulation failed");
7460 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_tx_nonode", CTLFLAG_RD,
7461 &sc->sc_stats.ast_tx_nonode, 0, "tx failed 'cuz no node");
7462 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_tx_nombuf", CTLFLAG_RD,
7463 &sc->sc_stats.ast_tx_nombuf, 0, "tx failed 'cuz no mbuf");
7464 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_tx_nomcl", CTLFLAG_RD,
7465 &sc->sc_stats.ast_tx_nomcl, 0, "tx failed 'cuz no cluster");
7466 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_tx_linear", CTLFLAG_RD,
7467 &sc->sc_stats.ast_tx_linear, 0, "tx linearized to cluster");
7468 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_tx_nodata", CTLFLAG_RD,
7469 &sc->sc_stats.ast_tx_nodata, 0, "tx discarded empty frame");
7470 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_tx_busdma", CTLFLAG_RD,
7471 &sc->sc_stats.ast_tx_busdma, 0, "tx failed for dma resrcs");
7472 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_tx_xretries", CTLFLAG_RD,
7473 &sc->sc_stats.ast_tx_xretries, 0, "tx failed 'cuz too many retries");
7474 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_tx_fifoerr", CTLFLAG_RD,
7475 &sc->sc_stats.ast_tx_fifoerr, 0, "tx failed 'cuz FIFO underrun");
7476 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_tx_filtered", CTLFLAG_RD,
7477 &sc->sc_stats.ast_tx_filtered, 0, "tx failed 'cuz xmit filtered");
7478 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_tx_shortretry", CTLFLAG_RD,
7479 &sc->sc_stats.ast_tx_shortretry, 0, "tx on-chip retries (short)");
7480 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_tx_longretry", CTLFLAG_RD,
7481 &sc->sc_stats.ast_tx_longretry, 0, "tx on-chip retries (long)");
7482 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_tx_badrate", CTLFLAG_RD,
7483 &sc->sc_stats.ast_tx_badrate, 0, "tx failed 'cuz bogus xmit rate");
7484 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_tx_noack", CTLFLAG_RD,
7485 &sc->sc_stats.ast_tx_noack, 0, "tx frames with no ack marked");
7486 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_tx_rts", CTLFLAG_RD,
7487 &sc->sc_stats.ast_tx_rts, 0, "tx frames with rts enabled");
7488 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_tx_cts", CTLFLAG_RD,
7489 &sc->sc_stats.ast_tx_cts, 0, "tx frames with cts enabled");
7490 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_tx_shortpre", CTLFLAG_RD,
7491 &sc->sc_stats.ast_tx_shortpre, 0, "tx frames with short preamble");
7492 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_tx_altrate", CTLFLAG_RD,
7493 &sc->sc_stats.ast_tx_altrate, 0, "tx frames with alternate rate");
7494 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_tx_protect", CTLFLAG_RD,
7495 &sc->sc_stats.ast_tx_protect, 0, "tx frames with protection");
7496 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_tx_ctsburst", CTLFLAG_RD,
7497 &sc->sc_stats.ast_tx_ctsburst, 0, "tx frames with cts and bursting");
7498 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_tx_ctsext", CTLFLAG_RD,
7499 &sc->sc_stats.ast_tx_ctsext, 0, "tx frames with cts extension");
7500 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_rx_nombuf", CTLFLAG_RD,
7501 &sc->sc_stats.ast_rx_nombuf, 0, "rx setup failed 'cuz no mbuf");
7502 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_rx_busdma", CTLFLAG_RD,
7503 &sc->sc_stats.ast_rx_busdma, 0, "rx setup failed for dma resrcs");
7504 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_rx_orn", CTLFLAG_RD,
7505 &sc->sc_stats.ast_rx_orn, 0, "rx failed 'cuz of desc overrun");
7506 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_rx_crcerr", CTLFLAG_RD,
7507 &sc->sc_stats.ast_rx_crcerr, 0, "rx failed 'cuz of bad CRC");
7508 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_rx_fifoerr", CTLFLAG_RD,
7509 &sc->sc_stats.ast_rx_fifoerr, 0, "rx failed 'cuz of FIFO overrun");
7510 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_rx_badcrypt", CTLFLAG_RD,
7511 &sc->sc_stats.ast_rx_badcrypt, 0, "rx failed 'cuz decryption");
7512 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_rx_badmic", CTLFLAG_RD,
7513 &sc->sc_stats.ast_rx_badmic, 0, "rx failed 'cuz MIC failure");
7514 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_rx_phyerr", CTLFLAG_RD,
7515 &sc->sc_stats.ast_rx_phyerr, 0, "rx failed 'cuz of PHY err");
7516 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_rx_tooshort", CTLFLAG_RD,
7517 &sc->sc_stats.ast_rx_tooshort, 0, "rx discarded 'cuz frame too short");
7518 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_rx_toobig", CTLFLAG_RD,
7519 &sc->sc_stats.ast_rx_toobig, 0, "rx discarded 'cuz frame too large");
7520 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_rx_packets", CTLFLAG_RD,
7521 &sc->sc_stats.ast_rx_packets, 0, "packet recv on the interface");
7522 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_rx_mgt", CTLFLAG_RD,
7523 &sc->sc_stats.ast_rx_mgt, 0, "management frames received");
7524 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_rx_ctl", CTLFLAG_RD,
7525 &sc->sc_stats.ast_rx_ctl, 0, "rx discarded 'cuz ctl frame");
7526 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_be_xmit", CTLFLAG_RD,
7527 &sc->sc_stats.ast_be_xmit, 0, "beacons transmitted");
7528 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_be_nombuf", CTLFLAG_RD,
7529 &sc->sc_stats.ast_be_nombuf, 0, "beacon setup failed 'cuz no mbuf");
7530 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_per_cal", CTLFLAG_RD,
7531 &sc->sc_stats.ast_per_cal, 0, "periodic calibration calls");
7532 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_per_calfail", CTLFLAG_RD,
7533 &sc->sc_stats.ast_per_calfail, 0, "periodic calibration failed");
7534 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_per_rfgain", CTLFLAG_RD,
7535 &sc->sc_stats.ast_per_rfgain, 0, "periodic calibration rfgain reset");
7536 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_rate_calls", CTLFLAG_RD,
7537 &sc->sc_stats.ast_rate_calls, 0, "rate control checks");
7538 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_rate_raise", CTLFLAG_RD,
7539 &sc->sc_stats.ast_rate_raise, 0, "rate control raised xmit rate");
7540 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_rate_drop", CTLFLAG_RD,
7541 &sc->sc_stats.ast_rate_drop, 0, "rate control dropped xmit rate");
7542 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_ant_defswitch", CTLFLAG_RD,
7543 &sc->sc_stats.ast_ant_defswitch, 0, "rx/default antenna switches");
7544 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_ant_txswitch", CTLFLAG_RD,
7545 &sc->sc_stats.ast_ant_txswitch, 0, "tx antenna switches");
7546 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_cabq_xmit", CTLFLAG_RD,
7547 &sc->sc_stats.ast_cabq_xmit, 0, "cabq frames transmitted");
7548 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_cabq_busy", CTLFLAG_RD,
7549 &sc->sc_stats.ast_cabq_busy, 0, "cabq found busy");
7550 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_tx_raw", CTLFLAG_RD,
7551 &sc->sc_stats.ast_tx_raw, 0, "tx frames through raw api");
7552 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_ff_txok", CTLFLAG_RD,
7553 &sc->sc_stats.ast_ff_txok, 0, "fast frames tx'd successfully");
7554 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_ff_txerr", CTLFLAG_RD,
7555 &sc->sc_stats.ast_ff_txerr, 0, "fast frames tx'd w/ error");
7556 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_ff_rx", CTLFLAG_RD,
7557 &sc->sc_stats.ast_ff_rx, 0, "fast frames rx'd");
7558 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_ff_flush", CTLFLAG_RD,
7559 &sc->sc_stats.ast_ff_flush, 0, "fast frames flushed from staging q");
7560 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_tx_qfull", CTLFLAG_RD,
7561 &sc->sc_stats.ast_tx_qfull, 0, "tx dropped 'cuz of queue limit");
7562 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_tx_nobuf", CTLFLAG_RD,
7563 &sc->sc_stats.ast_tx_nobuf, 0, "tx dropped 'cuz no ath buffer");
7564 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_tdma_update", CTLFLAG_RD,
7565 &sc->sc_stats.ast_tdma_update, 0, "TDMA slot timing updates");
7566 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_tdma_timers", CTLFLAG_RD,
7567 &sc->sc_stats.ast_tdma_timers, 0, "TDMA slot update set beacon timers");
7568 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_tdma_tsf", CTLFLAG_RD,
7569 &sc->sc_stats.ast_tdma_tsf, 0, "TDMA slot update set TSF");
7570 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_tdma_ack", CTLFLAG_RD,
7571 &sc->sc_stats.ast_tdma_ack, 0, "TDMA tx failed 'cuz ACK required");
7572 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_tx_raw_fail", CTLFLAG_RD,
7573 &sc->sc_stats.ast_tx_raw_fail, 0, "raw tx failed 'cuz h/w down");
7574 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_tx_nofrag", CTLFLAG_RD,
7575 &sc->sc_stats.ast_tx_nofrag, 0, "tx dropped 'cuz no ath frag buffer");
7577 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_be_missed", CTLFLAG_RD,
7578 &sc->sc_stats.ast_be_missed, 0, "number of -missed- beacons");