#!/bin/sh
#
# Copyright (c) 2000  The FreeBSD Project
# All rights reserved.
#
# Redistribution and use in source and binary forms, with or without
# modification, are permitted provided that the following conditions
# are met:
# 1. Redistributions of source code must retain the above copyright
#    notice, this list of conditions and the following disclaimer.
# 2. Redistributions in binary form must reproduce the above copyright
#    notice, this list of conditions and the following disclaimer in the
#    documentation and/or other materials provided with the distribution.
#
# THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND
# ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
# IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
# ARE DISCLAIMED.  IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE
# FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
# DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
# OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
# HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
# OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
# SUCH DAMAGE.
#
# $FreeBSD: src/etc/rc.d/atm1,v 1.12 2003/04/18 17:55:05 mtm Exp $
# $DragonFly: src/etc/rc.d/atm1,v 1.3 2005/11/19 21:47:32 swildner Exp $
#

# PROVIDE: atm1
# REQUIRE: root
# BEFORE: netif

. /etc/rc.subr

name="atm"
rcvar="atm_enable"
start_cmd="atm_start"
stop_cmd=":"

# ATM networking startup script
#
# Initial interface configuration.
# N.B. /usr is not mounted.
#
atm_start()
{
	# Locate all probed ATM adapters
	atmdev=`atm sh stat int | while read dev junk; do
		case ${dev} in
		hea[0-9] | hea[0-9][0-9])
			echo "${dev} "
			;;
		hfa[0-9] | hfa[0-9][0-9])
			echo "${dev} "
			;;
		idt[0-9] | idt[0-9][0-9])
			echo "${dev} "
			;;
		*)
			continue
			;;
		esac
	done`

	if [ -z "${atmdev}" ]; then
		echo 'No ATM adapters found'
		return 0
	fi

	# Load microcode into FORE adapters (if needed)
	if [ `expr "${atmdev}" : '.*hfa.*'` -ne 0 ]; then
		fore_dnld
	fi

	# Configure physical interfaces
	ilmid=0
	for phy in ${atmdev}; do
		echo -n "Configuring ATM device ${phy}:"

		# Define network interfaces
		eval netif_args=\$atm_netif_${phy}
		if [ -n "${netif_args}" ]; then
			atm set netif ${phy} ${netif_args} || continue
		else
			echo ' missing network interface definition'
			continue
		fi

		# Override physical MAC address
		eval macaddr_args=\$atm_macaddr_${phy}
		if [ -n "${macaddr_args}" ]; then
			case ${macaddr_args} in
			[Nn][Oo] | '')
				;;
			*)
				atm set mac ${phy} ${macaddr_args} || continue
				;;
			esac
		fi

		# Configure signalling manager
		eval sigmgr_args=\$atm_sigmgr_${phy}
		if [ -n "${sigmgr_args}" ]; then
			atm attach ${phy} ${sigmgr_args} || continue
		else
			echo ' missing signalling manager definition'
			continue
		fi

		# Configure UNI NSAP prefix
		eval prefix_args=\$atm_prefix_${phy}
		if [ `expr "${sigmgr_args}" : '[uU][nN][iI].*'` -ne 0 ]; then
			if [ -z "${prefix_args}" ]; then
				echo ' missing NSAP prefix for UNI interface'
				continue
			fi

			case ${prefix_args} in
			ILMI)
				ilmid=1
				;;
			*)
				atm set prefix ${phy} ${prefix_args} || continue
				;;
			esac
		fi

		atm_phy="${atm_phy} ${phy}"
		echo '.'
	done

	echo -n 'Starting initial ATM daemons:'
	# Start ILMI daemon (if needed)
	case ${ilmid} in
	1)
		echo -n ' ilmid'
		ilmid
		;;
	esac

	echo '.'
}

load_rc_config $name
run_rc_command "$1"