/* * Copyright (C) 2000 * Dr. Duncan McLennan Barclay, dmlb@ragnet.demon.co.uk. * * All rights reserved. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the distribution. * 3. Neither the name of the author nor the names of any co-contributors * may be used to endorse or promote products derived from this software * without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY DUNCAN BARCLAY AND CONTRIBUTORS ``AS IS'' AND * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE * ARE DISCLAIMED. IN NO EVENT SHALL DUNCAN BARCLAY OR CONTRIBUTORS BE LIABLE * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF * SUCH DAMAGE. * * $FreeBSD: src/sys/dev/ray/if_raymib.h,v 1.10.2.2 2001/08/14 22:54:07 dmlb Exp $ * $DragonFly: src/sys/dev/netif/ray/Attic/if_raymib.h,v 1.2 2003/06/17 04:28:29 dillon Exp $ * */ /* * Bit mask definitions for firmware versioning */ #define RAY_V4 0x1 #define RAY_V5 0x2 /* * MIB stuctures */ struct ray_mib_common_head { /*Offset*/ /*Size*/ u_int8_t mib_net_type; /*00*/ u_int8_t mib_ap_status; /*01*/ u_int8_t mib_ssid[IEEE80211_NWID_LEN]; /*02*/ /*20*/ u_int8_t mib_scan_mode; /*22*/ u_int8_t mib_apm_mode; /*23*/ u_int8_t mib_mac_addr[ETHER_ADDR_LEN]; /*24*/ /*06*/ u_int8_t mib_frag_thresh[2]; /*2a*/ /*02*/ u_int8_t mib_dwell_time[2]; /*2c*/ /*02*/ u_int8_t mib_beacon_period[2]; /*2e*/ /*02*/ u_int8_t mib_dtim_interval; /*30*/ u_int8_t mib_max_retry; /*31*/ u_int8_t mib_ack_timo; /*32*/ u_int8_t mib_sifs; /*33*/ u_int8_t mib_difs; /*34*/ u_int8_t mib_pifs; /*35*/ u_int8_t mib_rts_thresh[2]; /*36*/ /*02*/ u_int8_t mib_scan_dwell[2]; /*38*/ /*02*/ u_int8_t mib_scan_max_dwell[2]; /*3a*/ /*02*/ u_int8_t mib_assoc_timo; /*3c*/ u_int8_t mib_adhoc_scan_cycle; /*3d*/ u_int8_t mib_infra_scan_cycle; /*3e*/ u_int8_t mib_infra_super_scan_cycle; /*3f*/ u_int8_t mib_promisc; /*40*/ u_int8_t mib_uniq_word[2]; /*41*/ /*02*/ u_int8_t mib_slot_time; /*43*/ u_int8_t mib_roam_low_snr_thresh; /*44*/ u_int8_t mib_low_snr_count; /*45*/ u_int8_t mib_infra_missed_beacon_count; /*46*/ u_int8_t mib_adhoc_missed_beacon_count; /*47*/ u_int8_t mib_country_code; /*48*/ u_int8_t mib_hop_seq; /*49*/ u_int8_t mib_hop_seq_len; /*4a*/ } __attribute__((__packed__)); struct ray_mib_common_tail { u_int8_t mib_noise_filter_gain; /*00*/ u_int8_t mib_noise_limit_offset; /*01*/ u_int8_t mib_rssi_thresh_offset; /*02*/ u_int8_t mib_busy_thresh_offset; /*03*/ u_int8_t mib_sync_thresh; /*04*/ u_int8_t mib_test_mode; /*05*/ u_int8_t mib_test_min_chan; /*06*/ u_int8_t mib_test_max_chan; /*07*/ } __attribute__((__packed__)); struct ray_mib_4 { struct ray_mib_common_head mib_head; /*00*/ u_int8_t mib_cw_max; /*4b*/ u_int8_t mib_cw_min; /*4c*/ struct ray_mib_common_tail mib_tail; /*4d*/ } __attribute__((__packed__)); struct ray_mib_5 { struct ray_mib_common_head mib_head; /*00*/ u_int8_t mib_cw_max[2]; /*4b*/ /*02*/ u_int8_t mib_cw_min[2]; /*4d*/ /*02*/ struct ray_mib_common_tail mib_tail; /*4f*/ u_int8_t mib_allow_probe_resp; /*57*/ u_int8_t mib_privacy_must_start; /*58*/ u_int8_t mib_privacy_can_join; /*59*/ u_int8_t mib_basic_rate_set[8]; /*5a*/ /*08*/ } __attribute__((__packed__)); #define mib_net_type mib_head.mib_net_type #define mib_ap_status mib_head.mib_ap_status #define mib_ssid mib_head.mib_ssid #define mib_scan_mode mib_head.mib_scan_mode #define mib_apm_mode mib_head.mib_apm_mode #define mib_mac_addr mib_head.mib_mac_addr #define mib_frag_thresh mib_head.mib_frag_thresh #define mib_dwell_time mib_head.mib_dwell_time #define mib_beacon_period mib_head.mib_beacon_period #define mib_dtim_interval mib_head.mib_dtim_interval #define mib_max_retry mib_head.mib_max_retry #define mib_ack_timo mib_head.mib_ack_timo #define mib_sifs mib_head.mib_sifs #define mib_difs mib_head.mib_difs #define mib_pifs mib_head.mib_pifs #define mib_rts_thresh mib_head.mib_rts_thresh #define mib_scan_dwell mib_head.mib_scan_dwell #define mib_scan_max_dwell mib_head.mib_scan_max_dwell #define mib_assoc_timo mib_head.mib_assoc_timo #define mib_adhoc_scan_cycle mib_head.mib_adhoc_scan_cycle #define mib_infra_scan_cycle mib_head.mib_infra_scan_cycle #define mib_infra_super_scan_cycle \ mib_head.mib_infra_super_scan_cycle #define mib_promisc mib_head.mib_promisc #define mib_uniq_word mib_head.mib_uniq_word #define mib_slot_time mib_head.mib_slot_time #define mib_roam_low_snr_thresh mib_head.mib_roam_low_snr_thresh #define mib_low_snr_count mib_head.mib_low_snr_count #define mib_infra_missed_beacon_count \ mib_head.mib_infra_missed_beacon_count #define mib_adhoc_missed_beacon_count \ mib_head.mib_adhoc_missed_beacon_count #define mib_country_code mib_head.mib_country_code #define mib_hop_seq mib_head.mib_hop_seq #define mib_hop_seq_len mib_head.mib_hop_seq_len #define mib_noise_filter_gain mib_tail.mib_noise_filter_gain #define mib_noise_limit_offset mib_tail.mib_noise_limit_offset #define mib_rssi_thresh_offset mib_tail.mib_rssi_thresh_offset #define mib_busy_thresh_offset mib_tail.mib_busy_thresh_offset #define mib_sync_thresh mib_tail.mib_sync_thresh #define mib_test_mode mib_tail.mib_test_mode #define mib_test_min_chan mib_tail.mib_test_min_chan #define mib_test_max_chan mib_tail.mib_test_max_chan /* * MIB IDs for the update/report param commands */ #define RAY_MIB_NET_TYPE 0 #define RAY_MIB_AP_STATUS 1 #define RAY_MIB_SSID 2 #define RAY_MIB_SCAN_MODE 3 #define RAY_MIB_APM_MODE 4 #define RAY_MIB_MAC_ADDR 5 #define RAY_MIB_FRAG_THRESH 6 #define RAY_MIB_DWELL_TIME 7 #define RAY_MIB_BEACON_PERIOD 8 #define RAY_MIB_DTIM_INTERVAL 9 #define RAY_MIB_MAX_RETRY 10 #define RAY_MIB_ACK_TIMO 11 #define RAY_MIB_SIFS 12 #define RAY_MIB_DIFS 13 #define RAY_MIB_PIFS 14 #define RAY_MIB_RTS_THRESH 15 #define RAY_MIB_SCAN_DWELL 16 #define RAY_MIB_SCAN_MAX_DWELL 17 #define RAY_MIB_ASSOC_TIMO 18 #define RAY_MIB_ADHOC_SCAN_CYCLE 19 #define RAY_MIB_INFRA_SCAN_CYCLE 20 #define RAY_MIB_INFRA_SUPER_SCAN_CYCLE 21 #define RAY_MIB_PROMISC 22 #define RAY_MIB_UNIQ_WORD 23 #define RAY_MIB_SLOT_TIME 24 #define RAY_MIB_ROAM_LOW_SNR_THRESH 25 #define RAY_MIB_LOW_SNR_COUNT 26 #define RAY_MIB_INFRA_MISSED_BEACON_COUNT 27 #define RAY_MIB_ADHOC_MISSED_BEACON_COUNT 28 #define RAY_MIB_COUNTRY_CODE 29 #define RAY_MIB_HOP_SEQ 30 #define RAY_MIB_HOP_SEQ_LEN 31 #define RAY_MIB_CW_MAX 32 #define RAY_MIB_CW_MIN 33 #define RAY_MIB_NOISE_FILTER_GAIN 34 #define RAY_MIB_NOISE_LIMIT_OFFSET 35 #define RAY_MIB_RSSI_THRESH_OFFSET 36 #define RAY_MIB_BUSY_THRESH_OFFSET 37 #define RAY_MIB_SYNC_THRESH 38 #define RAY_MIB_TEST_MODE 39 #define RAY_MIB_TEST_MIN_CHAN 40 #define RAY_MIB_TEST_MAX_CHAN 41 #define RAY_MIB_ALLOW_PROBE_RESP 42 #define RAY_MIB_PRIVACY_MUST_START 43 #define RAY_MIB_PRIVACY_CAN_JOIN 44 #define RAY_MIB_BASIC_RATE_SET 45 #define RAY_MIB_VERSION 46 #define RAY_MIB_CUR_BSSID 47 #define RAY_MIB_CUR_INITED 48 #define RAY_MIB_CUR_DEF_TXRATE 49 #define RAY_MIB_CUR_ENCRYPT 50 #define RAY_MIB_CUR_NET_TYPE 51 #define RAY_MIB_CUR_SSID 52 #define RAY_MIB_CUR_PRIV_START 53 #define RAY_MIB_CUR_PRIV_JOIN 54 #define RAY_MIB_DES_BSSID 55 #define RAY_MIB_DES_INITED 56 #define RAY_MIB_DES_DEF_TXRATE 57 #define RAY_MIB_DES_ENCRYPT 58 #define RAY_MIB_DES_NET_TYPE 59 #define RAY_MIB_DES_SSID 60 #define RAY_MIB_DES_PRIV_START 61 #define RAY_MIB_DES_PRIV_JOIN 62 #define RAY_MIB_CUR_AP_STATUS 63 #define RAY_MIB_CUR_PROMISC 64 #define RAY_MIB_DES_AP_STATUS 65 #define RAY_MIB_DES_PROMISC 66 #define RAY_MIB_CUR_FRAMING 67 #define RAY_MIB_DES_FRAMING 68 #define RAY_MIB_LASTUSER 45 #define RAY_MIB_MAX 68 /* * Strings for the MIB */ #define RAY_MIB_STRINGS { \ "Network type", \ "AP status", \ "SSID", \ "Scan mode", \ "APM mode", \ "MAC address", \ "Fragmentation threshold", \ "Dwell time", \ "Beacon period", \ "DTIM_INTERVAL", \ "MAX_RETRY", \ "ACK_TIMO", \ "SIFS", \ "DIFS", \ "PIFS", \ "RTS_THRESH", \ "SCAN_DWELL", \ "SCAN_MAX_DWELL", \ "ASSOC_TIMO", \ "ADHOC_SCAN_CYCLE", \ "INFRA_SCAN_CYCLE", \ "INFRA_SUPER_SCAN_CYCLE", \ "PROMISC", \ "UNIQ_WORD", \ "SLOT_TIME", \ "ROAM_LOW_SNR_THRESH", \ "LOW_SNR_COUNT", \ "INFRA_MISSED_BEACON_COUNT", \ "ADHOC_MISSED_BEACON_COUNT", \ "COUNTRY_CODE", \ "HOP_SEQ", \ "HOP_SEQ_LEN", \ "CW_MAX", \ "CW_MIN", \ "NOISE_FILTER_GAIN", \ "NOISE_LIMIT_OFFSET", \ "RSSI_THRESH_OFFSET", \ "BUSY_THRESH_OFFSET", \ "SYNC_THRESH", \ "TEST_MODE", \ "TEST_MIN_CHAN", \ "TEST_MAX_CHAN", \ "ALLOW_PROBE_RESP", \ "PRIVACY_MUST_START", \ "PRIVACY_CAN_JOIN", \ "BASIC_RATE_SET", \ "Firmware version", \ "Current BSS Id", \ "Current INITED", \ "Current DEF_TXRATE", \ "Current ENCRYPT", \ "Current NET_TYPE", \ "Current SSID", \ "Current PRIV_START", \ "Current PRIV_JOIN", \ "Desired BSSID", \ "Desired INITED", \ "Desired DEF_TXRATE", \ "Desired ENCRYPT", \ "Desired NET_TYPE", \ "Desired SSID", \ "Desired PRIV_START", \ "Desired PRIV_JOIN", \ "Current AP_STATUS", \ "Current PROMISC", \ "Desired AP_STATUS", \ "Desired PROMISC", \ "Current FRAMING", \ "Desired FRAMING" \ } #define RAY_MIB_HELP_STRINGS { \ "0 Ad hoc, 1 Infrastructure", \ "0 Station, 1 Access Point", \ "", \ "0 Passive, 1 Active", \ "0 Off, 1 On", \ "", \ "Bytes", \ "DWELL_TIME", \ "BEACON_PERIOD", \ "DTIM_INTERVAL", \ "MAX_RETRY", \ "ACK_TIMO", \ "SIFS", \ "DIFS", \ "PIFS", \ "RTS_THRESH", \ "SCAN_DWELL", \ "SCAN_MAX_DWELL", \ "ASSOC_TIMO", \ "ADHOC_SCAN_CYCLE", \ "INFRA_SCAN_CYCLE", \ "INFRA_SUPER_SCAN_CYCLE", \ "PROMISC", \ "UNIQ_WORD", \ "SLOT_TIME", \ "ROAM_LOW_SNR_THRESH", \ "LOW_SNR_COUNT", \ "INFRA_MISSED_BEACON_COUNT", \ "ADHOC_MISSED_BEACON_COUNT", \ "COUNTRY_CODE", \ "HOP_SEQ", \ "HOP_SEQ_LEN", \ "CW_MAX", \ "CW_MIN", \ "NOISE_FILTER_GAIN", \ "NOISE_LIMIT_OFFSET", \ "RSSI_THRESH_OFFSET", \ "BUSY_THRESH_OFFSET", \ "SYNC_THRESH", \ "TEST_MODE", \ "TEST_MIN_CHAN", \ "TEST_MAX_CHAN", \ "ALLOW_PROBE_RESP", \ "PRIVACY_MUST_START", \ "PRIVACY_CAN_JOIN", \ "BASIC_RATE_SET", \ "", \ "", \ "0 Joined a net, 1 Created a net", \ "Current DEF_TXRATE", \ "Current ENCRYPT", \ "Current NET_TYPE", \ "", \ "Current PRIV_START", \ "Current PRIV_JOIN", \ "", \ "N/A", \ "Desired DEF_TXRATE", \ "Desired ENCRYPT", \ "Desired NET_TYPE", \ "", \ "Desired PRIV_START", \ "Desired PRIV_JOIN", \ "Current AP_STATUS", \ "Current PROMISC", \ "Desired AP_STATUS", \ "Desired PROMISC", \ "Current FRAMING", \ "Desired FRAMING" \ } /* * Applicable versions and work size for each MIB element */ #define RAY_MIB_INFO_SIZ4 1 #define RAY_MIB_INFO_SIZ5 2 #define RAY_MIB_SIZE(info, mib, version) \ info[(mib)][(version & RAY_V4)?RAY_MIB_INFO_SIZ4:RAY_MIB_INFO_SIZ5] #define RAY_MIB_INFO { \ {RAY_V4|RAY_V5, 1, 1}, /* RAY_MIB_NET_TYPE */ \ {RAY_V4|RAY_V5, 1, 1}, /* RAY_MIB_AP_STATUS */ \ {RAY_V4|RAY_V5, IEEE80211_NWID_LEN, \ IEEE80211_NWID_LEN},/* RAY_MIB_SSID */ \ {RAY_V4|RAY_V5, 1, 1}, /* RAY_MIB_SCAN_MODE */ \ {RAY_V4|RAY_V5, 1, 1}, /* RAY_MIB_APM_MODE */ \ {RAY_V4|RAY_V5, ETHER_ADDR_LEN, \ ETHER_ADDR_LEN},/* RAY_MIB_MAC_ADDR */ \ {RAY_V4|RAY_V5, 2, 2}, /* RAY_MIB_FRAG_THRESH */ \ {RAY_V4|RAY_V5, 2, 2}, /* RAY_MIB_DWELL_TIME */ \ {RAY_V4|RAY_V5, 2, 2}, /* RAY_MIB_BEACON_PERIOD */ \ {RAY_V4|RAY_V5, 1, 1}, /* RAY_MIB_DTIM_INTERVAL */ \ {RAY_V4|RAY_V5, 1, 1}, /* RAY_MIB_MAX_RETRY */ \ {RAY_V4|RAY_V5, 1, 1}, /* RAY_MIB_ACK_TIMO */ \ {RAY_V4|RAY_V5, 1, 1}, /* RAY_MIB_SIFS */ \ {RAY_V4|RAY_V5, 1, 1}, /* RAY_MIB_DIFS */ \ {RAY_V4|RAY_V5, 1, 1}, /* RAY_MIB_PIFS */ \ {RAY_V4|RAY_V5, 2, 2}, /* RAY_MIB_RTS_THRESH */ \ {RAY_V4|RAY_V5, 2, 2}, /* RAY_MIB_SCAN_DWELL */ \ {RAY_V4|RAY_V5, 2, 2}, /* RAY_MIB_SCAN_MAX_DWELL */ \ {RAY_V4|RAY_V5, 1, 1}, /* RAY_MIB_ASSOC_TIMO */ \ {RAY_V4|RAY_V5, 1, 1}, /* RAY_MIB_ADHOC_SCAN_CYCLE */ \ {RAY_V4|RAY_V5, 1, 1}, /* RAY_MIB_INFRA_SCAN_CYCLE */ \ {RAY_V4|RAY_V5, 1, 1}, /* RAY_MIB_INFRA_SUPER_SCAN_CYCLE */ \ {RAY_V4|RAY_V5, 1, 1}, /* RAY_MIB_PROMISC */ \ {RAY_V4|RAY_V5, 2, 2}, /* RAY_MIB_UNIQ_WORD */ \ {RAY_V4|RAY_V5, 1, 1}, /* RAY_MIB_SLOT_TIME */ \ {RAY_V4|RAY_V5, 1, 1}, /* RAY_MIB_ROAM_LOW_SNR_THRESH */ \ {RAY_V4|RAY_V5, 1, 1}, /* RAY_MIB_LOW_SNR_COUNT */ \ {RAY_V4|RAY_V5, 1, 1}, /* RAY_MIB_INFRA_MISSED_BEACON_COUNT */ \ {RAY_V4|RAY_V5, 1, 1}, /* RAY_MIB_ADHOC_MISSED_BEACON_COUNT */ \ {RAY_V4|RAY_V5, 1, 1}, /* RAY_MIB_COUNTRY_CODE */ \ {RAY_V4|RAY_V5, 1, 1}, /* RAY_MIB_HOP_SEQ */ \ {RAY_V4|RAY_V5, 1, 1}, /* RAY_MIB_HOP_SEQ_LEN */ \ {RAY_V4|RAY_V5, 1, 2}, /* RAY_MIB_CW_MAX */ \ {RAY_V4|RAY_V5, 1, 2}, /* RAY_MIB_CW_MIN */ \ {RAY_V4|RAY_V5, 1, 1}, /* RAY_MIB_NOISE_FILTER_GAIN */ \ {RAY_V4|RAY_V5, 1, 1}, /* RAY_MIB_NOISE_LIMIT_OFFSET */ \ {RAY_V4|RAY_V5, 1, 1}, /* RAY_MIB_RSSI_THRESH_OFFSET */ \ {RAY_V4|RAY_V5, 1, 1}, /* RAY_MIB_BUSY_THRESH_OFFSET */ \ {RAY_V4|RAY_V5, 1, 1}, /* RAY_MIB_SYNC_THRESH */ \ {RAY_V4|RAY_V5, 1, 1}, /* RAY_MIB_TEST_MODE */ \ {RAY_V4|RAY_V5, 1, 1}, /* RAY_MIB_TEST_MIN_CHAN */ \ {RAY_V4|RAY_V5, 1, 1}, /* RAY_MIB_TEST_MAX_CHAN */ \ { RAY_V5, 0, 1}, /* RAY_MIB_ALLOW_PROBE_RESP */ \ { RAY_V5, 0, 1}, /* RAY_MIB_PRIVACY_MUST_START */ \ { RAY_V5, 0, 1}, /* RAY_MIB_PRIVACY_CAN_JOIN */ \ { RAY_V5, 0, 8}, /* RAY_MIB_BASIC_RATE_SET */ \ {RAY_V4|RAY_V5, 1, 1}, /* RAY_MIB_VERSION */ \ {RAY_V4|RAY_V5, ETHER_ADDR_LEN, \ ETHER_ADDR_LEN},/* RAY_MIB_CUR_BSSID */ \ {RAY_V4|RAY_V5, 1, 1}, /* RAY_MIB_CUR_INITED */ \ {RAY_V4|RAY_V5, 1, 1}, /* RAY_MIB_CUR_DEF_TXRATE */ \ {RAY_V4|RAY_V5, 1, 1}, /* RAY_MIB_CUR_ENCRYPT */ \ {RAY_V4|RAY_V5, 1, 1}, /* RAY_MIB_CUR_NET_TYPE */ \ {RAY_V4|RAY_V5, IEEE80211_NWID_LEN, \ IEEE80211_NWID_LEN}, /* RAY_MIB_CUR_SSID */ \ {RAY_V4|RAY_V5, 1, 1}, /* RAY_MIB_CUR_PRIV_START */ \ {RAY_V4|RAY_V5, 1, 1}, /* RAY_MIB_CUR_PRIV_JOIN */ \ {RAY_V4|RAY_V5, ETHER_ADDR_LEN, \ ETHER_ADDR_LEN},/* RAY_MIB_DES_BSSID */ \ {RAY_V4|RAY_V5, 1, 1}, /* RAY_MIB_DES_INITED */ \ {RAY_V4|RAY_V5, 1, 1}, /* RAY_MIB_DES_DEF_TXRATE */ \ {RAY_V4|RAY_V5, 1, 1}, /* RAY_MIB_DES_ENCRYPT */ \ {RAY_V4|RAY_V5, 1, 1}, /* RAY_MIB_DES_NET_TYPE */ \ {RAY_V4|RAY_V5, IEEE80211_NWID_LEN, \ IEEE80211_NWID_LEN}, /* RAY_MIB_DES_SSID */ \ {RAY_V4|RAY_V5, 1, 1}, /* RAY_MIB_DES_PRIV_START */ \ {RAY_V4|RAY_V5, 1, 1}, /* RAY_MIB_DES_PRIV_JOIN */ \ {RAY_V4|RAY_V5, 1, 1}, /* RAY_MIB_CUR_AP_STATUS */ \ {RAY_V4|RAY_V5, 1, 1}, /* RAY_MIB_CUR_PROMISC */ \ {RAY_V4|RAY_V5, 1, 1}, /* RAY_MIB_DES_AP_STATUS */ \ {RAY_V4|RAY_V5, 1, 1}, /* RAY_MIB_DES_PROMISC */ \ {RAY_V4|RAY_V5, 1, 1}, /* RAY_MIB_CUR_FRAMING */ \ {RAY_V4|RAY_V5, 1, 1} /* RAY_MIB_DES_FRAMING */ \ } /* * MIB values * * I've included comments as to where the numbers have originated * from. * * Linux refers to ray_cs.c and rayctl.h from version 167 of the * Linux Raylink driver. * * NetBSD refers to if_ray.c from version 1.12 of the NetBSD Raylink * driver. * * Symb refers to numbers cleaned from the 802.11 specification, * discussion with 802.11 knowledgable people at Symbionics or * stuff needed by me (i.e. me, * aps, ifo, hjl). * * V4 and V5 refer to settings for version 4 and version 5 of * the firmware. * * DOC refers to the * Combined Interface Requirements Specification * and Interface Design Document (IRS/IDD) * for the * WLAN System Interfaces Between the * HOST COMPUTER and the * PCMCIA WLAN INTERFACE CARD * Revision ECF 5.00 * 17 June, 1998 */ /* Obtained by raycontrol _before_ downloading * * WebGear Aviator * * # raycontrol -i ray0 * Firmware version 4 * Network type 0x01 0 Ad hoc, 1 Infrastructure * AP status 0x00 0 Station, 1 Access Point * SSID * Scan mode 0x01 0 Passive, 1 Active * APM mode 0x00 0 Off, 1 On * MAC address 00:00:8f:48:e4:44 * Fragmentation threshold 0x0200 FRAG_THRESH * Dwell tIME 0x01 DWELL_TIME * Beacon period 0x01 BEACON_PERIOD * DTIM_INTERVAL 0x05 DTIM_INTERVAL * MAX_RETRY 0x03 MAX_RETRY * ACK_TIMO 0x8c ACK_TIMO * SIFS 0x1e SIFS * DIFS 0x82 DIFS * PIFS 0xce PIFS * RTS_THRESH 0x0100 RTS_THRESH * SCAN_DWELL 0xfc18 SCAN_DWELL * SCAN_MAX_DWELL 0xc180 SCAN_MAX_DWELL * ASSOC_TIMO 0x05 ASSOC_TIMO * ADHOC_SCAN_CYCLE 0x04 ADHOC_SCAN_CYCLE * INFRA_SCAN_CYCLE 0x02 INFRA_SCAN_CYCLE * INFRA_SUPER_SCAN_CYCLE 0x04 INFRA_SUPER_SCAN_CYCLE * PROMISC 0x00 PROMISC * UNIQ_WORD 0x0cbd UNIQ_WORD * SLOT_TIME 0x4e SLOT_TIME * ROAM_LOW_SNR_THRESH 0x20 ROAM_LOW_SNR_THRESH * LOW_SNR_COUNT 0x04 LOW_SNR_COUNT * INFRA_MISSED_BEACON_COUNT 0x04 INFRA_MISSED_BEACON_COUNT * ADHOC_MISSED_BEACON_COUNT 0x04 ADHOC_MISSED_BEACON_COUNT * COUNTRY_CODE 0x01 COUNTRY_CODE * HOP_SEQ 0x07 HOP_SEQ * HOP_SEQ_LEN 0x4e HOP_SEQ_LEN * CW_MAX 0x3f CW_MAX * CW_MIN 0x0f CW_MIN * NOISE_FILTER_GAIN 0x00 NOISE_FILTER_GAIN * NOISE_LIMIT_OFFSET 0x00 NOISE_LIMIT_OFFSET * RSSI_THRESH_OFFSET 0x70 RSSI_THRESH_OFFSET * BUSY_THRESH_OFFSET 0x70 BUSY_THRESH_OFFSET * SYNC_THRESH 0x07 SYNC_THRESH * TEST_MODE 0x00 TEST_MODE * TEST_MIN_CHAN 0x02 TEST_MIN_CHAN * TEST_MAX_CHAN 0x02 TEST_MAX_CHAN * * Raylink * Firmware version 5 * Network type 0x01 0 Ad hoc, 1 Infrastructure * AP status 0x00 0 Station, 1 Access Point * SSID ESSID1 * Scan mode 0x01 0 Passive, 1 Active * APM mode 0x00 0 Off, 1 On * MAC address 00:00:8f:a8:17:06 * Fragmentation threshold 0x7fff Bytes * Dwell time 0x0080 DWELL_TIME * Beacon period 0x0100 BEACON_PERIOD * DTIM_INTERVAL 0x01 DTIM_INTERVAL * MAX_RETRY 0x1f MAX_RETRY * ACK_TIMO 0x86 ACK_TIMO * SIFS 0x1c SIFS * DIFS 0x82 DIFS * PIFS 0x4e PIFS * RTS_THRESH 0x7fff RTS_THRESH * SCAN_DWELL 0x04e2 SCAN_DWELL * SCAN_MAX_DWELL 0x38a4 SCAN_MAX_DWELL * ASSOC_TIMO 0x05 ASSOC_TIMO * ADHOC_SCAN_CYCLE 0x08 ADHOC_SCAN_CYCLE * INFRA_SCAN_CYCLE 0x02 INFRA_SCAN_CYCLE * INFRA_SUPER_SCAN_CYCLE 0x08 INFRA_SUPER_SCAN_CYCLE * PROMISC 0x00 PROMISC * UNIQ_WORD 0x0cbd UNIQ_WORD * SLOT_TIME 0x32 SLOT_TIME * ROAM_LOW_SNR_THRESH 0xff ROAM_LOW_SNR_THRESH * LOW_SNR_COUNT 0xff LOW_SNR_COUNT * INFRA_MISSED_BEACON_COUNT 0x02 INFRA_MISSED_BEACON_COUNT * ADHOC_MISSED_BEACON_COUNT 0xff ADHOC_MISSED_BEACON_COUNT * COUNTRY_CODE 0x01 COUNTRY_CODE * HOP_SEQ 0x0b HOP_SEQ * HOP_SEQ_LEN 0x55 HOP_SEQ_LEN * CW_MAX 0x003f CW_MAX * CW_MIN 0x000f CW_MIN * NOISE_FILTER_GAIN 0x04 NOISE_FILTER_GAIN * NOISE_LIMIT_OFFSET 0x08 NOISE_LIMIT_OFFSET * RSSI_THRESH_OFFSET 0x28 RSSI_THRESH_OFFSET * BUSY_THRESH_OFFSET 0x28 BUSY_THRESH_OFFSET * SYNC_THRESH 0x07 SYNC_THRESH * TEST_MODE 0x00 TEST_MODE * TEST_MIN_CHAN 0x02 TEST_MIN_CHAN * TEST_MAX_CHAN 0x02 TEST_MAX_CHAN * ALLOW_PROBE_RESP 0x00 ALLOW_PROBE_RESP * PRIVACY_MUST_START 0x00 PRIVACY_MUST_START * PRIVACY_CAN_JOIN 0x00 PRIVACY_CAN_JOIN * BASIC_RATE_SET 0x02 BASIC_RATE_SET */ /* * mib_net_type * * DOC 0x01 - Defines network type for Start and Join * - Network commands. * * As the V4 cards don't do infra we have to use adhoc. For V5 cards * we follow standard FreeBSD practise and use infrastructure mode. */ #define RAY_MIB_NET_TYPE_ADHOC 0x00 #define RAY_MIB_NET_TYPE_INFRA 0x01 #define RAY_MIB_NET_TYPE_V4 RAY_MIB_NET_TYPE_ADHOC #define RAY_MIB_NET_TYPE_V5 RAY_MIB_NET_TYPE_INFRA /* * mib_ap_status * * DOC 0x00 - Applicable only when Network Type is * - Infrastructure. */ #define RAY_MIB_AP_STATUS_TERMINAL 0x00 #define RAY_MIB_AP_STATUS_AP 0x01 #define RAY_MIB_AP_STATUS_V4 RAY_MIB_AP_STATUS_TERMINAL #define RAY_MIB_AP_STATUS_V5 RAY_MIB_AP_STATUS_TERMINAL /* * mib_ssid * * DOC ESSID1 - Service Set ID. Can be any ASCII string * - up to 32 bytes in length. If the string is * - less than 32 bytes long, it must be * - followed by a byte of 00h. * * Symb - windows setting comes from the Aviator software v1.1 */ #define RAY_MIB_SSID_WINDOWS "NETWORK_NAME" #define RAY_MIB_SSID_RAYLINK "ESSID1" #define RAY_MIB_SSID_V4 RAY_MIB_SSID_WINDOWS #define RAY_MIB_SSID_V5 RAY_MIB_SSID_RAYLINK /* * mib_scan_mode * * DOC 0x01 - Defines acquisition approach for * - terminals operating in either Ad Hoc or * - Infrastructure Networks. N/A for APs. */ #define RAY_MIB_SCAN_MODE_PASSIVE 0x00 #define RAY_MIB_SCAN_MODE_ACTIVE 0x01 #define RAY_MIB_SCAN_MODE_V4 RAY_MIB_SCAN_MODE_ACTIVE #define RAY_MIB_SCAN_MODE_V5 RAY_MIB_SCAN_MODE_ACTIVE /* * mib_apm_mode * * DOC 0x00 - Defines power management mode for * - stations operating in either Ad Hoc or * - Infrastructure Networks. Must always * - be 0 for APs. */ #define RAY_MIB_APM_MODE_NONE 0x00 #define RAY_MIB_APM_MODE_POWERSAVE 0x01 #define RAY_MIB_APM_MODE_V4 RAY_MIB_APM_MODE_NONE #define RAY_MIB_APM_MODE_V5 RAY_MIB_APM_MODE_NONE /* * mib_mac_addr * * DOC - MAC Address to be used by WIC (For * - format see Figure 3.2.4.1.2-1, MAC * - Address Format). Host may echo card * - supplied address or use locally * - administered address. */ /* * mib_frag_thresh * * DOC 0x7fff - Maximum over-the-air packet size (in * - bytes) * * Symb 0xXXXX - you really should fragment when in low signal * - conditions but getting it wrong * crucifies the performance */ #define RAY_MIB_FRAG_THRESH_MINIMUM 0 #define RAY_MIB_FRAG_THRESH_MAXIMUM 2346 #define RAY_MIB_FRAG_THRESH_DISABLE 0x7fff #define RAY_MIB_FRAG_THRESH_V4 RAY_MIB_FRAG_THRESH_DISABLE #define RAY_MIB_FRAG_THRESH_V5 RAY_MIB_FRAG_THRESH_DISABLE /* * mib_dwell_time * * DOC 0x0080 - Defines hop dwell time in Kusec. * - Required only of stations which intend * - to issue a Start Network command. * - Forward Compatible Firmware (Build * - 5) requires that the dwell time be one of * - the set 16, 32, 64, 128, and 256. * * Linux.h - 16k * 2**n, n=0-4 in Kus * Linux.c-V4 0x0200 * Linux.c-V5 0x0080 - 128 Kus * NetBSD-V4 0x0200 - from Linux * NetBSD-V4 0x0400 - "divined" * NetBSD-V5 0x0080 * Symb-V4 0xXXXX - 802.11 dwell time is XXX Kus * Symb-V5 0xXXXX - 802.11 dwell time is XXX Kus * * XXX confirm that 1024Kus is okay for windows driver - how? and see * XXX how it is over the maximum */ #define RAY_MIB_DWELL_TIME_MINIMUM 1 #define RAY_MIB_DWELL_TIME_MAXIMUM 390 #define RAY_MIB_DWELL_TIME_V4 0x0400 #define RAY_MIB_DWELL_TIME_V5 0x0080 /* * mib_beacon_period * * DOC 0x0100 - Defines time between target beacon * - transmit times (TBTT) in Kusec. * - Forward Compatible Firmware (Build * - 5) requires that the Beacon Period be an * - integral multiple of the Dwell Time (not * - exceeding 255 hops). * - Required only of stations which intend * - to issue a Start Network command. * * Linux.h - n * a_hop_time in Kus * Linux.c-V4 0x0001 * Linux.c-V5 0x0100 - 256 Kus * NetBSD-V4 0x0001 - from Linux * NetBSD-V4 0x0000 - "divined" * NetBSD-V5 0x0100 * Symb-V4 0x0001 - best performance is one beacon each dwell XXX * Symb-V5 0x0080 - best performance is one beacon each dwell XXX * * XXX V4 should probably set this to dwell_time */ #define RAY_MIB_BEACON_PERIOD_MINIMUM 1 #define RAY_MIB_BEACON_PERIOD_MAXIMUM 0xffff #define RAY_MIB_BEACON_PERIOD_V4 0x0001 #define RAY_MIB_BEACON_PERIOD_V5 (2*RAY_MIB_DWELL_TIME_V5) /* * mib_dtim_interval * * DOC 0x01 - Number of beacons per DTIM period. * - Only APs will use this parameter, to set * - the DTIM period. * * Linux.h - in beacons * Linux.c 0x01 * NetBSD 0x01 * Symb 0xXX - need to find out what DTIM is */ #define RAY_MIB_DTIM_INTERVAL_MINIMUM 1 #define RAY_MIB_DTIM_INTERVAL_MAXIMUM 255 #define RAY_MIB_DTIM_INTERVAL_V4 0x01 #define RAY_MIB_DTIM_INTERVAL_V5 0x01 /* * mib_max_retry * * DOC 31 - Number of times WIC will attempt to * - retransmit a failed packet. * * Linux.c 0x07 * NetBSD 0x01 - "documented default for 5/6" * NetBSD 0x07 - from Linux * NetBSD 0x03 - "divined" * Symb 0xXX - 7 retries seems okay but check with APS */ #define RAY_MIB_MAX_RETRY_MINIMUM 0 #define RAY_MIB_MAX_RETRY_MAXIMUM 255 #define RAY_MIB_MAX_RETRY_V4 0x07 #define RAY_MIB_MAX_RETRY_V5 0x1f /* * mib_ack_timo * * DOC 0x86 - Time WIC will wait after completion of * - a transmit before timing out anticipated * - ACK (2 usec steps). Should equal * - SIFS + constant. * * Linux.c 0xa3 * NetBSD 0x86 - documented default for 5/6 * NetBSD 0xa3 - from Linux * NetBSD 0xa3 - "divined" * Symb 0xXX - this must be a 802.11 defined setting? */ #define RAY_MIB_ACK_TIMO_MINIMUM 0 #define RAY_MIB_ACK_TIMO_MAXIMUM 255 #define RAY_MIB_ACK_TIMO_V4 0xa3 #define RAY_MIB_ACK_TIMO_V5 0x86 /* * mib_sifs * * DOC 0x1c - SIFS time in usec. * * Linux.c 0x1d * NetBSD 0x1c - documented default for 5/6 * NetBSD 0x1d - from Linux * NetBSD 0x1d - "divined" * Symb 0xXX - default SIFS for 802.11 */ #define RAY_MIB_SIFS_MINIMUM 28 #define RAY_MIB_SIFS_MAXIMUM 62 #define RAY_MIB_SIFS_V4 0x1d #define RAY_MIB_SIFS_V5 0x1c /* * mib_difs * * DOC 0x82 - DIFS time in usec. */ #define RAY_MIB_DIFS_MINIMUM 130 #define RAY_MIB_DIFS_MAXIMUM 255 #define RAY_MIB_DIFS_V4 0x82 #define RAY_MIB_DIFS_V5 0x82 /* * mib_pifs * * DOC 78 - PIFS time in usec. (Not currently * - implemented. */ #define RAY_MIB_PIFS_MINIMUM 78 #define RAY_MIB_PIFS_MAXIMUM 255 #define RAY_MIB_PIFS_V4 0xce #define RAY_MIB_PIFS_V5 0x4e /* * mib_rts_thresh * * DOC 0x7ffff - Threshold size in bytes below which * - messages will not require use of RTS * - Protocol. * * Linux.c 0x7fff * NetBSD 0x7fff - disabled * Symb 0xXXXX - need to set this realistically to get CTS/RTS mode * working right */ #define RAY_MIB_RTS_THRESH_MINIMUM 0 #define RAY_MIB_RTS_THRESH_MAXIMUM 2346 #define RAY_MIB_RTS_THRESH_DISABLE 0x7fff #define RAY_MIB_RTS_THRESH_V4 RAY_MIB_RTS_THRESH_DISABLE #define RAY_MIB_RTS_THRESH_V5 RAY_MIB_RTS_THRESH_DISABLE /* * mib_scan_dwell * * DOC 0x04e2 - Time channel remains clear after probe * - transmission prior to hopping to next * - channel. (in 2 msec steps). * * Linux.c-V4 0xfb1e - 128572us * Linix.c-V5 0x04e2 - 2500us * NetBSD-V4 0xfb1e * NetBSD-V5 0x04e2 * Symb 0xXXXX - Check that v4 h/w can do 2.5ms and default it */ #define RAY_MIB_SCAN_DWELL_MINIMUM 1 #define RAY_MIB_SCAN_DWELL_MAXIMUM 65535 #define RAY_MIB_SCAN_DWELL_V4 0xfb1e #define RAY_MIB_SCAN_DWELL_V5 0x04e2 /* * mib_scan_max_dwell * * DOC 0x38a4 - Time to remain on a frequency channel * - if CCA is detected after probe * - transmission. (in 2 usec steps). * * Linux.c-V4 0xc75c - 102072us * Linix.c-V5 0x38a4 - 29000us * NetBSD-V4 0xc75c * NetBSD-V5 0x38a4 * Symb 0xXXXX - see above - this may be total time before giving up */ #define RAY_MIB_SCAN_MAX_DWELL_MINIMUM 1 #define RAY_MIB_SCAN_MAX_DWELL_MAXIMUM 65535 #define RAY_MIB_SCAN_MAX_DWELL_V4 0xc75c #define RAY_MIB_SCAN_MAX_DWELL_V5 0x38a4 /* * mib_assoc_timo * * DOC 0x05 - Time (in hops) a station waits after * - transmitting an Association Request * - Message before association attempt is * - considered failed. N/A for Ad Hoc * - Networks and for APs in Infrastructure */ #define RAY_MIB_ASSOC_TIMO_MINIMUM 0 #define RAY_MIB_ASSOC_TIMO_MAXIMUM 255 #define RAY_MIB_ASSOC_TIMO_V4 0x05 #define RAY_MIB_ASSOC_TIMO_V5 0x05 /* * mib_adhoc_scan_cycle * * DOC 0x08 - Maximum number of times to cycle * - through frequency hopping pattern as * - part of scanning during Ad Hoc * - Acquisition. */ #define RAY_MIB_ADHOC_SCAN_CYCLE_MINIMUM 1 #define RAY_MIB_ADHOC_SCAN_CYCLE_MAXIMUM 255 #define RAY_MIB_ADHOC_SCAN_CYCLE_V4 0x08 #define RAY_MIB_ADHOC_SCAN_CYCLE_V5 0x08 /* * mib_infra_scan_cycle * * DOC 0x02 - Number of times to cycle through * - frequency hopping pattern as part of * - scanning during Infrastructure Network * - Acquisition. */ #define RAY_MIB_INFRA_SCAN_CYCLE_MINIMUM 1 #define RAY_MIB_INFRA_SCAN_CYCLE_MAXIMUM 255 #define RAY_MIB_INFRA_SCAN_CYCLE_V4 0x02 #define RAY_MIB_INFRA_SCAN_CYCLE_V5 0x02 /* * mib_infra_super_scan_cycle * * DOC 0x08 - Number of times to repeat an * - Infrastructure scan cycle if no APs are * - found before indicating a failure. */ #define RAY_MIB_INFRA_SUPER_SCAN_CYCLE_MINIMUM 1 #define RAY_MIB_INFRA_SUPER_SCAN_CYCLE_MAXIMUM 255 #define RAY_MIB_INFRA_SUPER_SCAN_CYCLE_V4 0x08 #define RAY_MIB_INFRA_SUPER_SCAN_CYCLE_V5 0x08 /* * mib_promisc * * DOC 0x00 - Controls operation of WIC in * - promiscuous mode. */ #define RAY_MIB_PROMISC_DISABLED 0 #define RAY_MIB_PROMISC_ENABLED 1 #define RAY_MIB_PROMISC_V4 0x00 #define RAY_MIB_PROMISC_V5 0x00 /* * mib_uniq_word * * DOC 0x0cdb - Unique word pattern (Transmitted as * - 0CBDh per 802.11) */ #define RAY_MIB_UNIQ_WORD_MINIMUM 0 #define RAY_MIB_UNIQ_WORD_MAXIMUM 0xffff #define RAY_MIB_UNIQ_WORD_V4 0x0cbd #define RAY_MIB_UNIQ_WORD_V5 0x0cbd /* * mib_slot_time * * DOC 0x32 - Slot time in usec * * Linux.c-V4 0x4e * Linix.c-V5 0x32 * NetBSD-V4 0x4e - Linux * NetBSD-V4 0x18 - "divined" * NetBSD-V5 0x32 - mentions spec. is 50us i.e. 0x32 * Symb 0xXX - wtf 0x4e = 78 */ #define RAY_MIB_SLOT_TIME_MINIMUM 1 #define RAY_MIB_SLOT_TIME_MAXIMUM 128 #define RAY_MIB_SLOT_TIME_V4 0x4e #define RAY_MIB_SLOT_TIME_V5 0x32 /* * mib_roam_low_snr_thresh * * DOC 0xff - SNR Threshold for use by roaming * - algorithm. [Low power count is * - incremented when Beacon is received at * - SNR lower than Roaming Low SNR * - Threshold.] To disable, set to FFh. * * Linux.c 0xff * NetBSD-V4 0xff - Linux * NetBSD-V4 0x30 - "divined" * NetBSD-V5 0xff - disabled * NetBSD.h - if below this inc count * Symb 0xXX - hmm is 0xff really disabled? need this to work */ #define RAY_MIB_ROAM_LOW_SNR_THRESH_MINIMUM 0 #define RAY_MIB_ROAM_LOW_SNR_THRESH_MAXIMUM 255 #define RAY_MIB_ROAM_LOW_SNR_THRESH_DISABLED 0xff #define RAY_MIB_ROAM_LOW_SNR_THRESH_V4 RAY_MIB_ROAM_LOW_SNR_THRESH_DISABLED #define RAY_MIB_ROAM_LOW_SNR_THRESH_V5 RAY_MIB_ROAM_LOW_SNR_THRESH_DISABLED /* * mib_low_snr_count * * DOC 0xff - Threshold that number of consecutive * - beacons received at SNR < Roaming * - Low SNR Threshold must exceed * - before roaming processing begins. To * - disable, set to FFh. * * Linux.c 0xff * NetBSD 0x07 - "divined - check" and marked as disabled * NetBSD 0xff - disabled * NetBSD.h - roam after cnt below thrsh * Symb 0xXX - hmm is 0xff really disabled? need * - this to work in infrastructure mode with mutliple APs */ #define RAY_MIB_LOW_SNR_COUNT_MINIMUM 0 #define RAY_MIB_LOW_SNR_COUNT_MAXIMUM 255 #define RAY_MIB_LOW_SNR_COUNT_DISABLED 0xff #define RAY_MIB_LOW_SNR_COUNT_V4 RAY_MIB_LOW_SNR_COUNT_DISABLED #define RAY_MIB_LOW_SNR_COUNT_V5 RAY_MIB_LOW_SNR_COUNT_DISABLED /* * mib_infra_missed_beacon_count * * DOC 0x02 - Threshold that number of consecutive * - beacons not received must exceed * - before roaming processing begins in an * - infrastructure network. To disable, set * - to FFh. * Linux.c 0x05 * NetBSD 0x02 - documented default for 5/6 * NetBSD 0x05 - Linux * NetBSD 0x07 - "divined - check, looks fishy" * Symb 0xXX - 5 missed beacons is probably okay */ #define RAY_MIB_INFRA_MISSED_BEACON_COUNT_MINIMUM 0 #define RAY_MIB_INFRA_MISSED_BEACON_COUNT_MAXIMUM 255 #define RAY_MIB_INFRA_MISSED_BEACON_COUNT_V4 0x05 #define RAY_MIB_INFRA_MISSED_BEACON_COUNT_V5 0x02 /* * mib_adhoc_missed_beacon_count * * DOC 0xff - Threshold that number of consecutive * - beacons transmitted by a terminal must * - exceed before reacquisition processing * - begins in Ad Hoc Network. */ #define RAY_MIB_ADHOC_MISSED_BEACON_COUNT_MINIMUM 0 #define RAY_MIB_ADHOC_MISSED_BEACON_COUNT_MAXIMUM 255 #define RAY_MIB_ADHOC_MISSED_BEACON_COUNT_DISABLED 0xff #define RAY_MIB_ADHOC_MISSED_BEACON_COUNT_V4 RAY_MIB_ADHOC_MISSED_BEACON_COUNT_DISABLED #define RAY_MIB_ADHOC_MISSED_BEACON_COUNT_V5 RAY_MIB_ADHOC_MISSED_BEACON_COUNT_DISABLED /* * mib_country_code * * DOC 0x01 - Country set of hopping patterns * - (element value in beacon) * - Note: Japan Test is for a special test * - mode required by the Japanese * - regulatory authorities. */ #define RAY_MIB_COUNTRY_CODE_MIMIMUM 0x01 #define RAY_MIB_COUNTRY_CODE_MAXIMUM 0x09 #define RAY_MIB_COUNTRY_CODE_USA 0x01 #define RAY_MIB_COUNTRY_CODE_EUROPE 0x02 #define RAY_MIB_COUNTRY_CODE_JAPAN 0x03 #define RAY_MIB_COUNTRY_CODE_KOREA 0x04 #define RAY_MIB_COUNTRY_CODE_SPAIN 0x05 #define RAY_MIB_COUNTRY_CODE_FRANCE 0x06 #define RAY_MIB_COUNTRY_CODE_ISRAEL 0x07 #define RAY_MIB_COUNTRY_CODE_AUSTRALIA 0x08 #define RAY_MIB_COUNTRY_CODE_JAPAN_TEST 0x09 #define RAY_MIB_COUNTRY_CODE_V4 RAY_MIB_COUNTRY_CODE_USA #define RAY_MIB_COUNTRY_CODE_V5 RAY_MIB_COUNTRY_CODE_USA /* * mib_hop_seq * * DOC 0x0b - Hop Pattern to use. (Currently 66 * - US/Europe plus 12 Japanese). * * NetBSD.h - no longer supported */ #define RAY_MIB_HOP_SEQ_MINIMUM 6 #define RAY_MIB_HOP_SEQ_MAXIMUM 72 #define RAY_MIB_HOP_SEQ_V4 0x0b #define RAY_MIB_HOP_SEQ_V5 0x04 /* * mib_hop_seq_len * * DOC 0x4f - Number of frequency channels in * - hopping pattern is now set to the value * - defined in IEEE802.11 for the selected * - Current Country Code. */ #define RAY_MIB_HOP_SEQ_LEN_MINIMUM 1 #define RAY_MIB_HOP_SEQ_LEN_MAXIMUM 79 #define RAY_MIB_HOP_SEQ_LEN_V4 0x4e #define RAY_MIB_HOP_SEQ_LEN_V5 0x4f /* * All from here down are the same in Linux/NetBSD and seem to be sane. */ #define RAY_MIB_CW_MAX_V4 0x3f #define RAY_MIB_CW_MAX_V5 0x003f #define RAY_MIB_CW_MIN_V4 0x0f #define RAY_MIB_CW_MIN_V5 0x000f /* * Symb 0xXX - these parameters will affect the clear channel * assesment false triggering * */ #define RAY_MIB_NOISE_FILTER_GAIN_DEFAULT 0x04 #define RAY_MIB_NOISE_LIMIT_OFFSET_DEFAULT 0x08 #define RAY_MIB_RSSI_THRESH_OFFSET_DEFAULT 0x28 #define RAY_MIB_BUSY_THRESH_OFFSET_DEFAULT 0x28 #define RAY_MIB_SYNC_THRESH_DEFAULT 0x07 #define RAY_MIB_TEST_MODE_NORMAL 0x0 #define RAY_MIB_TEST_MODE_ANT_1 0x1 #define RAY_MIB_TEST_MODE_ATN_2 0x2 #define RAY_MIB_TEST_MODE_ATN_BOTH 0x3 #define RAY_MIB_TEST_MODE_DEFAULT RAY_MIB_TEST_MODE_NORMAL #define RAY_MIB_TEST_MIN_CHAN_DEFAULT 0x02 #define RAY_MIB_TEST_MAX_CHAN_DEFAULT 0x02 #define RAY_MIB_ALLOW_PROBE_RESP_DISALLOW 0x0 #define RAY_MIB_ALLOW_PROBE_RESP_ALLOW 0x1 #define RAY_MIB_ALLOW_PROBE_RESP_DEFAULT RAY_MIB_ALLOW_PROBE_RESP_DISALLOW #define RAY_MIB_PRIVACY_MUST_START_NOWEP 0x0 #define RAY_MIB_PRIVACY_MUST_START_WEP 0x1 #define RAY_MIB_PRIVACY_MUST_START_DEFAULT RAY_MIB_PRIVACY_MUST_START_NOWEP #define RAY_MIB_PRIVACY_CAN_JOIN_NOWEP 0x0 #define RAY_MIB_PRIVACY_CAN_JOIN_WEP 0x1 #define RAY_MIB_PRIVACY_CAN_JOIN_DONT_CARE 0x2 #define RAY_MIB_PRIVACY_CAN_JOIN_DEFAULT RAY_MIB_PRIVACY_CAN_JOIN_NOWEP #define RAY_MIB_BASIC_RATE_SET_MINIMUM 1 #define RAY_MIB_BASIC_RATE_SET_MAXIMUM 4 #define RAY_MIB_BASIC_RATE_SET_500K 1 #define RAY_MIB_BASIC_RATE_SET_1000K 2 #define RAY_MIB_BASIC_RATE_SET_1500K 3 #define RAY_MIB_BASIC_RATE_SET_2000K 4 #define RAY_MIB_BASIC_RATE_SET_DEFAULT RAY_MIB_BASIC_RATE_SET_2000K /* * IOCTL support */ struct ray_param_req { int r_failcause; u_int8_t r_paramid; u_int8_t r_len; u_int8_t r_data[256]; }; struct ray_stats_req { u_int64_t rxoverflow; /* Number of rx overflows */ u_int64_t rxcksum; /* Number of checksum errors */ u_int64_t rxhcksum; /* Number of header checksum errors */ u_int8_t rxnoise; /* Average receiver level */ }; #define RAY_FAILCAUSE_EIDRANGE 1 #define RAY_FAILCAUSE_ELENGTH 2 /* device can possibly return up to 255 */ #define RAY_FAILCAUSE_EDEVSTOP 256 /* Get a param the data is a ray_param_req structure */ #define SIOCSRAYPARAM SIOCSIFGENERIC #define SIOCGRAYPARAM SIOCGIFGENERIC /* Get the error counters the data is a ray_stats_req structure */ #define SIOCGRAYSTATS _IOWR('i', 201, struct ifreq) #define SIOCGRAYSIGLEV _IOWR('i', 202, struct ifreq) #define RAY_NSIGLEVRECS 8 #define RAY_NSIGLEV 8 #define RAY_NANTENNA 8 struct ray_siglev { u_int8_t rsl_host[ETHER_ADDR_LEN]; /* MAC address */ u_int8_t rsl_siglevs[RAY_NSIGLEV]; /* levels, newest in [0] */ u_int8_t rsl_antennas[RAY_NANTENNA]; /* best antenna */ struct timeval rsl_time; /* time of last packet */ };