/*- * Copyright (c) 1999,2000,2001 Jonathan Lemon * All rights reserved. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the distribution. * 3. Neither the name of the author nor the names of any co-contributors * may be used to endorse or promote products derived from this software * without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF * SUCH DAMAGE. * * $FreeBSD: src/sys/dev/gx/if_gxreg.h,v 1.1.2.1 2001/11/15 03:09:23 jlemon Exp $ * $DragonFly: src/sys/dev/netif/gx/Attic/if_gxreg.h,v 1.2 2003/06/17 04:28:26 dillon Exp $ */ /* * Intel vendor ID */ #define INTEL_VENDORID 0x8086 /* * Intel gigabit ethernet device ID */ #define DEVICEID_WISEMAN 0x1000 #define DEVICEID_LIVINGOOD_FIBER 0x1001 #define DEVICEID_LIVINGOOD_COPPER 0x1004 #define DEVICEID_CORDOVA_COPPER 0x1008 #define DEVICEID_CORDOVA_FIBER 0x1009 #define DEVICEID_CORDOVA2_COPPER 0x100D /* * chip register offsets. These are memory mapped registers * which can be accessed with the CSR_READ_4()/CSR_WRITE_4() macros. * Each register must be accessed using 32 bit operations. */ #define GX_CTRL 0x0000 /* control register */ #define GX_STATUS 0x0008 /* status register */ #define GX_EEPROM_CTRL 0x0010 /* EEPROM/Flash control/data */ #define GX_CTRL_EXT 0x0018 /* extended device control */ #define GX_MDIC 0x0020 /* MDI control */ #define GX_FLOW_CTRL_BASE 0x0028 /* flow control address low/high */ #define GX_FLOW_CTRL_TYPE 0x0030 /* flow control type */ #define GX_VET 0x0038 /* VLAN ethertype */ #define GX_RX_ADDR_BASE 0x0040 /* 16 pairs of receive address low/high */ #define GX_INT_READ 0x00C0 /* read interrupts */ #define GX_INT_FORCE 0x00C8 /* force an interrupt */ #define GX_INT_MASK_SET 0x00D0 /* interrupt mask set/read */ #define GX_INT_MASK_CLR 0x00D8 /* interrupt mask clear */ #define GX_RX_CONTROL 0x0100 /* RX control */ /* 82542 and older 82543 chips */ #define GX_RX_OLD_INTR_DELAY 0x0108 /* RX delay timer */ #define GX_RX_OLD_RING_BASE 0x0110 /* RX descriptor base address */ #define GX_RX_OLD_RING_LEN 0x0118 /* RX descriptor length */ #define GX_RX_OLD_RING_HEAD 0x0120 /* RX descriptor head */ #define GX_RX_OLD_RING_TAIL 0x0128 /* RX descriptor tail */ /* 82542 and older 82543 chips */ #define GX_OLD_FCRTH 0x0160 /* flow control rcv threshhold high */ #define GX_OLD_FCRTL 0x0168 /* flow control rcv threshhold low */ #define GX_FCTTV 0x0170 /* flow control xmit timer value */ #define GX_TX_CONFIG 0x0178 /* xmit configuration (tbi mode) */ #define GX_RX_CONFIG 0x0180 /* recv configuration word */ #define GX_MULTICAST_BASE 0x0200 /* multicast table array base */ #define GX_TX_CONTROL 0x0400 /* TX control */ #define GX_TX_IPG 0x0410 /* TX interpacket gap */ /* 82542 and older 82543 chips */ #define GX_TX_OLD_RING_BASE 0x0420 /* TX descriptor base address */ #define GX_TX_OLD_RING_LEN 0x0428 /* TX descriptor length */ #define GX_TX_OLD_RING_HEAD 0x0430 /* TX descriptor head */ #define GX_TX_OLD_RING_TAIL 0x0438 /* TX descriptor tail */ #define GX_TX_OLD_INTR_DELAY 0x0440 /* TX interrupt delay value */ #define GX_TBT 0x0448 /* TX burst timer */ #define GX_AIT 0x0458 /* adaptive IFS throttle */ #define GX_VFTA_BASE 0x0600 /* VLAN filter table array base */ #define GX_PKT_BUFFER_ALLOC 0x1000 /* Packet buffer allocation */ #define GX_ERT 0x2000 /* Early receive threshold */ #define GX_RX_OLD_DMA_CTRL 0x2028 /* RX descriptor control */ /* newer 82543 chips */ #define GX_FCRTH 0x2160 /* flow control rcv threshhold high */ #define GX_FCRTL 0x2168 /* flow control rcv threshhold low */ /* newer 82543 chips */ #define GX_RX_RING_BASE 0x2800 /* RX descriptor base address */ #define GX_RX_RING_LEN 0x2808 /* RX descriptor length */ #define GX_RX_RING_HEAD 0x2810 /* RX descriptor head */ #define GX_RX_RING_TAIL 0x2818 /* RX descriptor tail */ #define GX_RX_INTR_DELAY 0x2820 /* RX delay timer */ #define GX_RX_DMA_CTRL 0x2820 /* RX descriptor control */ #define GX_EARLY_TX_THRESH 0x3000 /* early transmit threshold */ #define GX_TX_OLD_DMA_CTRL 0x3028 /* TX descriptor control */ /* newer 82543 chips */ #define GX_TX_RING_BASE 0x3800 /* TX descriptor base address */ #define GX_TX_RING_LEN 0x3808 /* TX descriptor length */ #define GX_TX_RING_HEAD 0x3810 /* TX descriptor head */ #define GX_TX_RING_TAIL 0x3818 /* TX descriptor tail */ #define GX_TX_INTR_DELAY 0x3820 /* TX interrupt delay value */ #define GX_TX_DMA_CTRL 0x3828 /* TX descriptor control */ #define GX_CRCERRS 0x4000 /* CRC error count */ #define GX_ALGNERRC 0x4004 /* alignment error count */ #define GX_SYMERRS 0x4008 /* symbol error count */ #define GX_RXERRC 0x400C /* RX error count */ #define GX_MPC 0x4010 /* missed packets count */ #define GX_SCC 0x4014 /* single collision count */ #define GX_ECOL 0x4018 /* excessive collision count */ #define GX_MCC 0x401C /* multiple collision count */ #define GX_LATECOL 0x4020 /* late collision count */ #define GX_COLC 0x4020 /* collision count */ #define GX_TUC 0x402C /* transmit underrun count */ #define GX_DC 0x4030 /* defer count */ #define GX_TNCRS 0x4034 /* transmit - no CRS */ #define GX_SEC 0x4038 /* sequence error count */ #define GX_CEXTERR 0x403C /* carrier extension error count */ #define GX_RLEC 0x4040 /* receive length error count */ #define GX_RDMAUC 0x4044 /* receive DMA underrun count */ #define GX_XONRXC 0x4048 /* XON received count */ #define GX_XONTXC 0x404C /* XON transmitted count */ #define GX_XOFFRXC 0x4050 /* XOFF received count */ #define GX_XOFFTXC 0x4054 /* XOFF transmitted count */ #define GX_FCRUC 0x4058 /* FC received unsupported count */ #define GX_PRC64 0x405C /* packets rcvd (64 bytes) */ #define GX_PRC127 0x4060 /* packets rcvd (65 - 127 bytes) */ #define GX_PRC255 0x4064 /* packets rcvd (128 - 255 bytes) */ #define GX_PRC511 0x4068 /* packets rcvd (256 - 511 bytes) */ #define GX_PRC1023 0x406C /* packets rcvd (512 - 1023 bytes) */ #define GX_PRC1522 0x4070 /* packets rcvd (1023 - 1522 bytes) */ #define GX_GPRC 0x4074 /* good packets received */ #define GX_BPRC 0x4078 /* broadcast packets received */ #define GX_MPRC 0x407C /* multicast packets received */ #define GX_GPTC 0x4080 /* good packets transmitted */ #define GX_GORC 0x4088 /* good octets received (low/high) */ #define GX_GOTC 0x4090 /* good octets transmitted (low/high) */ #define GX_RNBC 0x40A0 /* receive no buffers count */ #define GX_RUC 0x40A4 /* receive undersize count */ #define GX_RFC 0x40A8 /* receive fragment count */ #define GX_ROC 0x40AC /* receive oversize count */ #define GX_RJC 0x40B0 /* receive jabber count */ #define GX_TOR 0x40C0 /* total octets received (low/high) */ #define GX_TOT 0x40C8 /* total octets transmitted (low/high) */ #define GX_TPR 0x40D0 /* total packets received */ #define GX_TPT 0x40D4 /* total packets transmitted */ #define GX_PTC64 0x40D8 /* packets transmitted (64 B) */ #define GX_PTC127 0x40DC /* packets xmitted (65 - 127 B) */ #define GX_PTC255 0x40E0 /* packets xmitted (128 - 255 B) */ #define GX_PTC511 0x40E4 /* packets xmitted (256 - 511 B) */ #define GX_PTC1023 0x40E8 /* packets xmitted (512 - 1023 B) */ #define GX_PTC1522 0x40EC /* packets xmitted (1023 - 1522 B) */ #define GX_MPTC 0x40F0 /* multicast packets transmitted */ #define GX_BPTC 0x40F4 /* broadcast packets transmitted */ #define GX_TSCTC 0x40F8 /* TCP segmentation context xmitted */ #define GX_TSCTFC 0x40FC /* TCP segmentation context fail */ #define GX_RX_CSUM_CONTROL 0x5000 /* receive checksum control */ #define GX_RDFH 0x8000 /* RX data fifo head */ #define GX_RDFT 0x8008 /* RX data fifo tail */ #define GX_TDFH 0x8010 /* TX data fifo head */ #define GX_TDFT 0x8018 /* TX data fifo tail */ #define GX_RBM_BASE 0x10000 /* packet buffer memory */ /* GX_RX_CSUM_CONTROL */ #define GX_CSUM_START_MASK 0x000ff #define GX_CSUM_IP 0x00100 #define GX_CSUM_TCP 0x00200 /* GX_CTRL register */ #define GX_CTRL_DUPLEX 0x00000001 /* full duplex */ #define GX_CTRL_BIGENDIAN 0x00000002 /* 1 == big endian */ #define GX_CTRL_PCI_PRIORITY 0x00000004 /* 1 == fairness */ #define GX_CTRL_LINK_RESET 0x00000008 #define GX_CTRL_TEST_MODE 0x00000010 #define GX_CTRL_AUTOSPEED 0x00000020 #define GX_CTRL_SET_LINK_UP 0x00000040 #define GX_CTRL_INVERT_LOS 0x00000080 /* invert loss of signal */ #define GX_CTRL_SPEEDMASK 0x00000300 /* 2 bits */ #define GX_CTRL_FORCESPEED 0x00000800 #define GX_CTRL_FORCEDUPLEX 0x00001000 #define GX_CTRL_GPIO_0 0x00040000 /* Software defined pin #0 */ #define GX_CTRL_GPIO_1 0x00080000 /* Software defined pin #1 */ #define GX_CTRL_GPIO_2 0x00100000 /* Software defined pin #2 */ #define GX_CTRL_GPIO_3 0x00200000 /* Software defined pin #3 */ #define GX_CTRL_GPIO_DIR_0 0x00400000 /* Pin is Input(0)/Output(1) */ #define GX_CTRL_GPIO_DIR_1 0x00800000 /* Pin is Input(0)/Output(1) */ #define GX_CTRL_GPIO_DIR_2 0x01000000 /* Pin is Input(0)/Output(1) */ #define GX_CTRL_GPIO_DIR_3 0x02000000 /* Pin is Input(0)/Output(1) */ #define GX_CTRL_DEVICE_RESET 0x04000000 #define GX_CTRL_RX_FLOWCTRL 0x08000000 /* RX flowcontrol enable */ #define GX_CTRL_TX_FLOWCTRL 0x10000000 /* TX flowcontrol enable */ #define GX_CTRL_VLAN_ENABLE 0x40000000 /* GX_STATUS register */ #define GX_STAT_DUPLEX 0x00000001 #define GX_STAT_LINKUP 0x00000002 #define GX_STAT_XMITCLK_OK 0x00000004 #define GX_STAT_RECVCLK_OK 0x00000008 #define GX_STAT_XMIT_OFF 0x00000010 #define GX_STAT_TBIMODE 0x00000020 #define GX_STAT_SPEED_MASK 0x000000C0 /* 2 bits, not valid w/TBI */ #define GX_STAT_AUTOSPEED_MASK 0x00000300 /* 2 bits, not valid w/TBI */ #define GX_STAT_MTXCLK_OK 0x00000400 #define GX_STAT_PCI66 0x00000800 #define GX_STAT_BUS64 0x00001000 #define GX_SPEED_10MB 0x00000000 #define GX_SPEED_100MB 0x00000040 #define GX_SPEED_1000MB 0x00000080 /* GX_EEPROM_CTRL register */ #define GX_EE_CLOCK 0x0001 /* software clock */ #define GX_EE_SELECT 0x0002 /* chip select */ #define GX_EE_DATA_IN 0x0004 #define GX_EE_DATA_OUT 0x0008 #define GX_EE_FLASH_CTRL 0x0030 /* 0x02 == enable writes */ /* serial EEPROM opcodes */ #define GX_EE_OPC_WRITE 0x5 #define GX_EE_OPC_READ 0x6 #define GX_EE_OPC_ERASE 0x7 #define GX_EE_OPC_SIZE 3 /* bits of opcode */ #define GX_EE_ADDR_SIZE 6 /* bits of address */ /* EEPROM map offsets */ #define GX_EEMAP_MAC 0x00 /* station address (6 bytes) */ #define GX_EEMAP_INIT1 0x0A /* init control (2 bytes) */ /* GX_CTRL_EXT register */ #define GX_CTRLX_GPIO_4 0x00000010 /* Software defined pin #4 */ #define GX_CTRLX_GPIO_5 0x00000020 /* Software defined pin #5 */ #define GX_CTRLX_GPIO_6 0x00000040 /* Software defined pin #6 */ #define GX_CTRLX_GPIO_7 0x00000080 /* Software defined pin #7 */ #define GX_CTRLX_GPIO_DIR_4 0x00000100 /* Pin is Input(0)/Output(1) */ #define GX_CTRLX_GPIO_DIR_5 0x00000200 /* Pin is Input(0)/Output(1) */ #define GX_CTRLX_GPIO_DIR_6 0x00000400 /* Pin is Input(0)/Output(1) */ #define GX_CTRLX_GPIO_DIR_7 0x00000800 /* Pin is Input(0)/Output(1) */ #define GX_CTRLX_EEPROM_RESET 0x00002000 /* PCI_RST type EEPROM reset */ #define GX_CTRLX_SPEED_BYPASS 0x00008000 /* use CTRL.SPEED setting */ /* * Defines for MII/GMII PHY. * * GPIO bits 0-3 are controlled by GX_CTRL, 4-7 by GX_CTRL_EXT. */ #define GX_CTRL_GPIO_DIR (GX_CTRL_GPIO_DIR_3) #define GX_CTRL_GPIO_DIR_MASK (GX_CTRL_GPIO_DIR_0 | GX_CTRL_GPIO_DIR_1 | \ GX_CTRL_GPIO_DIR_2 | GX_CTRL_GPIO_DIR_3) #define GX_CTRL_PHY_IO GX_CTRL_GPIO_2 #define GX_CTRL_PHY_IO_DIR GX_CTRL_GPIO_DIR_2 #define GX_CTRL_PHY_CLK GX_CTRL_GPIO_3 #define GX_CTRLX_GPIO_DIR (GX_CTRLX_GPIO_DIR_4) #define GX_CTRLX_GPIO_DIR_MASK (GX_CTRLX_GPIO_DIR_4 | GX_CTRLX_GPIO_DIR_5 | \ GX_CTRLX_GPIO_DIR_6 | GX_CTRLX_GPIO_DIR_7) #define GX_CTRLX_PHY_RESET GX_CTRLX_GPIO_4 #define GX_PHY_PREAMBLE 0xffffffff #define GX_PHY_PREAMBLE_LEN 32 #define GX_PHY_SOF 0x01 #define GX_PHY_TURNAROUND 0x02 #define GX_PHY_OP_WRITE 0x01 #define GX_PHY_OP_READ 0x02 #define GX_PHY_READ_LEN 14 #define GX_PHY_WRITE_LEN 32 /* GX_RX_ADDR registers */ #define GX_RA_VALID 0x80000000 /* GX_TX_CONFIG register */ #define GX_TXCFG_AUTONEG 0x80000000 #define GX_TXCFG_SWCONFIG 0x80000000 /* GX_RX_CONFIG register */ #define GX_RXCFG_INVALID 0x08000000 /* GX_RX_CONTROL register */ #define GX_RXC_RESET 0x00000001 #define GX_RXC_ENABLE 0x00000002 #define GX_RXC_STORE_BAD_PKT 0x00000004 #define GX_RXC_UNI_PROMISC 0x00000008 #define GX_RXC_MULTI_PROMISC 0x00000010 #define GX_RXC_LONG_PKT_ENABLE 0x00000020 #define GX_RXC_LOOPBACK 0x000000C0 #define GX_RXC_RX_THOLD_MASK 0x00000300 #define GX_RXC_MCAST_OFF_MASK 0x00003000 #define GX_RXC_BCAST_ACCEPT 0x00008000 #define GX_RXC_RX_BSIZE_MASK 0x00030000 #define GX_RXC_VLAN_ENABLE 0x00040000 #define GX_RXC_CFI_ENABLE 0x00080000 /* canonical form enable */ #define GX_RXC_CFI 0x00100000 #define GX_RXC_DISCARD_PAUSE 0x00400000 #define GX_RXC_PASS_MAC 0x00800000 #define GX_RXC_RX_BSIZE_SCALE 0x02000000 /* multiply BSIZE by 16 */ #define GX_RXC_STRIP_ETHERCRC 0x04000000 /* bits for GX_RXC_RX_THOLD */ #define GX_RXC_RX_THOLD_HALF 0x00000000 #define GX_RXC_RX_THOLD_QUARTER 0x00000100 #define GX_RXC_RX_THOLD_EIGHTH 0x00000200 /* bits for GX_RXC_RX_BSIZE_MASK */ #define GX_RXC_RX_BSIZE_2K 0x00000000 #define GX_RXC_RX_BSIZE_1K 0x00010000 #define GX_RXC_RX_BSIZE_512 0x00020000 #define GX_RXC_RX_BSIZE_256 0x00030000 /* GX_TX_CONTROL register */ #define GX_TXC_RESET 0x00000001 #define GX_TXC_ENABLE 0x00000002 #define GX_TXC_PAD_SHORT_PKTS 0x00000008 #define GX_TXC_COLL_RETRY_MASK 0x00000FF0 #define GX_TXC_COLL_TIME_MASK 0x003FF000 #define GX_TXC_XMIT_XOFF 0x00400000 #define GX_TXC_PKT_BURST_ENABLE 0x00800000 #define GX_TXC_REXMT_LATE_COLL 0x01000000 #define GX_TXC_NO_REXMT_UNDERRN 0x02000000 /* bits for GX_TXC_COLL_RETRY_MASK */ #define GX_TXC_COLL_RETRY_16 0x000000F0 /* 16 attempts at retransmit */ /* bits for GX_TXC_COLL_TIME_MASK */ #define GX_TXC_COLL_TIME_HDX 0x00200000 #define GX_TXC_COLL_TIME_FDX 0x00040000 /* GX_INT bits */ #define GX_INT_XMIT_DONE 0x00000001 #define GX_INT_XMIT_EMPTY 0x00000002 #define GX_INT_LINK_CHANGE 0x00000004 #define GX_INT_RCV_SEQ_ERR 0x00000008 #define GX_INT_RCV_THOLD 0x00000010 #define GX_INT_RCV_OVERRUN 0x00000040 #define GX_INT_RCV_TIMER 0x00000080 #define GX_INT_MDIO_DONE 0x00000200 #define GX_INT_C_SETS 0x00000400 #define GX_INT_GPI_MASK 0x00007800 #define GX_INT_ALL \ (GX_INT_XMIT_DONE | GX_INT_XMIT_EMPTY | GX_INT_LINK_CHANGE | \ GX_INT_RCV_SEQ_ERR | GX_INT_RCV_THOLD | GX_INT_RCV_OVERRUN | \ GX_INT_RCV_TIMER | GX_INT_MDIO_DONE | GX_INT_C_SETS | GX_INT_GPI_MASK) #if 0 #define GX_INT_WANTED \ (GX_INT_XMIT_DONE | /*GX_INT_XMIT_EMPTY |*/ GX_INT_LINK_CHANGE | \ GX_INT_RCV_SEQ_ERR | GX_INT_RCV_THOLD | GX_INT_RCV_OVERRUN | \ GX_INT_RCV_TIMER | GX_INT_C_SETS) #else #define GX_INT_WANTED \ (GX_INT_XMIT_DONE | GX_INT_RCV_THOLD | GX_INT_RCV_TIMER | \ GX_INT_LINK_CHANGE) #endif /* PCI space */ #define GX_PCI_VENDOR_ID 0x0000 #define GX_PCI_DEVICE_ID 0x0002 #define GX_PCI_COMMAND 0x0004 #define GX_PCI_STATUS 0x0006 #define GX_PCI_REVID 0x0008 #define GX_PCI_CLASSCODE 0x0009 #define GX_PCI_CACHELEN 0x000C #define GX_PCI_LATENCY_TIMER 0x000D #define GX_PCI_HEADER_TYPE 0x000E #define GX_PCI_LOMEM 0x0010 #define GX_PCI_SUBVEN_ID 0x002C #define GX_PCI_SYBSYS_ID 0x002E #define GX_PCI_BIOSROM 0x0030 #define GX_PCI_CAPABILITY_PTR 0x0034 #define GX_PCI_INTLINE 0x003C #define GX_PCI_INTPIN 0x003D #define GX_PCI_MINGNT 0x003E #define GX_PCI_MINLAT 0x003F /* generic TX descriptor */ struct gx_tx_desc { u_int64_t :64; u_int16_t :16; u_int8_t :4, tx_type:4, u_int8_t :5, tx_extended:1, :2; u_int32_t :32; }; /* legacy TX descriptor */ struct gx_tx_desc_old { u_int64_t tx_addr; u_int16_t tx_len; u_int8_t tx_csum_offset; u_int8_t tx_command; u_int8_t tx_status; u_int8_t tx_csum_start; u_int16_t tx_vlan; }; #define GX_TXOLD_END_OF_PKT 0x01 /* end of packet */ #define GX_TXOLD_ETHER_CRC 0x02 /* insert ethernet CRC */ #define GX_TXOLD_INSERT_CSUM 0x04 /* insert checksum */ #define GX_TXOLD_REPORT_STATUS 0x08 /* report packet status */ #define GX_TXOLD_REPORT_SENT 0x10 /* report packet sent */ #define GX_TXOLD_EXTENSION 0x20 /* extended format */ #define GX_TXOLD_VLAN_ENABLE 0x40 /* use vlan */ #define GX_TXOLD_INT_DELAY 0x80 /* delay interrupt */ /* bits for tx_status */ #define GX_TXSTAT_DONE 0x01 /* descriptor done */ #define GX_TXSTAT_EXCESS_COLL 0x02 /* excess collisions */ #define GX_TXSTAT_LATE_COLL 0x04 /* late collision */ #define GX_TXSTAT_UNDERRUN 0x08 /* transmit underrun */ /* TX descriptor for checksum offloading context */ struct gx_tx_desc_ctx { u_int8_t tx_ip_csum_start; u_int8_t tx_ip_csum_offset; u_int16_t tx_ip_csum_end; u_int8_t tx_tcp_csum_start; u_int8_t tx_tcp_csum_offset; u_int16_t tx_tcp_csum_end; u_int32_t tx_len:20, tx_type:4, tx_command:8; u_int8_t tx_status; u_int8_t tx_hdrlen; u_int16_t tx_mss; }; #define GX_TXCTX_TCP_PKT 0x01 /* its a TCP packet */ #define GX_TXCTX_IP_PKT 0x02 /* its an IP packet */ #define GX_TXCTX_TCP_SEG_EN 0x04 /* TCP segmentation enable */ #define GX_TXCTX_REPORT_STATUS 0x08 /* report packet status */ #define GX_TXCTX_EXTENSION 0x20 /* extended format */ #define GX_TXCTX_INT_DELAY 0x80 /* delay interrupt */ /* TX descriptor for data */ struct gx_tx_desc_data { u_int64_t tx_addr; u_int32_t tx_len:20, tx_type:4, tx_command:8; u_int8_t tx_status; u_int8_t tx_options; u_int16_t tx_vlan; }; #define GX_TXTCP_END_OF_PKT 0x01 /* end of packet */ #define GX_TXTCP_ETHER_CRC 0x02 /* insert ethernet CRC */ #define GX_TXTCP_TCP_SEG_EN 0x04 /* TCP segmentation enable */ #define GX_TXTCP_REPORT_STATUS 0x08 /* report packet status */ #define GX_TXTCP_REPORT_SENT 0x10 /* report packet sent */ #define GX_TXTCP_EXTENSION 0x20 /* extended format */ #define GX_TXTCP_VLAN_ENABLE 0x40 /* use vlan */ #define GX_TXTCP_INT_DELAY 0x80 /* delay interrupt */ /* bits for tx_options */ #define GX_TXTCP_OPT_IP_CSUM 0x01 /* insert IP checksum */ #define GX_TXTCP_OPT_TCP_CSUM 0x02 /* insert UDP/TCP checksum */ /* RX descriptor data structure */ struct gx_rx_desc { u_int64_t rx_addr; u_int16_t rx_len; u_int16_t rx_csum; u_int16_t rx_staterr; /* status + error fields */ u_int16_t rx_special; }; /* bits for rx_status portion of rx_staterr */ #define GX_RXSTAT_COMPLETED 0x01 /* completed */ #define GX_RXSTAT_END_OF_PACKET 0x02 /* end of this packet */ #define GX_RXSTAT_IGNORE_CSUM 0x04 /* ignore computed checksum */ #define GX_RXSTAT_VLAN_PKT 0x08 /* matched vlan */ #define GX_RXSTAT_HAS_TCP_CSUM 0x20 /* TCP checksum calculated */ #define GX_RXSTAT_HAS_IP_CSUM 0x40 /* IP checksum calculated */ #define GX_RXSTAT_INEXACT_MATCH 0x80 /* must check address */ /* bits for rx_error portion of rx_staterr */ #define GX_RXERR_CRC 0x0100 /* CRC or alignment error */ #define GX_RXERR_SYMBOL 0x0200 /* symbol error */ #define GX_RXERR_SEQUENCE 0x0400 /* sequence error */ #define GX_RXERR_CARRIER 0x1000 /* carrier extension error */ #define GX_RXERR_TCP_CSUM 0x2000 /* TCP/UDP checksum error */ #define GX_RXERR_IP_CSUM 0x4000 /* IP checksum error */ #define GX_RXERR_RX_DATA 0x8000 /* RX data error */ /* drop packet on these errors */ #define GX_INPUT_ERROR \ (GX_RXERR_CRC | GX_RXERR_SYMBOL | GX_RXERR_SEQUENCE | \ GX_RXERR_CARRIER | GX_RXERR_RX_DATA)