# SCSI mode page data base. # Copyright (c) 1995 HD Associates # Copyright (c) 2001 The FreeBSD Project # (contact: dufault@hda.com) # All rights reserved. # # Redistribution and use in source and binary forms, with or without # modification, are permitted provided that the following conditions # are met: # 1. Redistributions of source code must retain the above copyright # notice, this list of conditions and the following disclaimer. # 2. Redistributions in binary form must reproduce the above copyright # notice, this list of conditions and the following disclaimer in the # documentation and/or other materials provided with the distribution. # 3. The name of HD Associates # may not be used to endorse or promote products derived from this software # without specific prior written permission. # # THIS SOFTWARE IS PROVIDED BY HD ASSOCIATES ``AS IS'' AND # ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE # IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE # ARE DISCLAIMED. IN NO EVENT SHALL HD ASSOCIATES BE LIABLE # FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL # DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS # OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) # HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT # LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY # OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF # SUCH DAMAGE. # # $FreeBSD: head/share/misc/scsi_modes 312750 2017-01-25 11:47:16Z mav $ # # The ordering is alphabetical by page name, as it appears in the SCSI spec. # 'i' is a byte-sized integral types, followed by a field width of # 1 through 4 (1 to 4 bytes). # # 'b' is a bit-sized integral type # 't' is a bitfield type- followed by a bit field width # # 'c' values are character arrays # 'z' values are null-padded strings # # # '*' suppresses assignment (for 'seeking'). # Bitfields are MSB to LSB. # ALL DEVICE TYPES 0x0a,0x03 "Command Duration Limit A"; 0x0a,0x04 "Command Duration Limit B"; 0x0a "Control" { {TST} t3 {TMF_ONLY} t1 {DPICZ} t1 {D_SENSE} t1 {GLTSD} t1 {RLEC} t1 {Queue Algorithm Modifier} t4 {NUAR} t1 {QErr} t2 {DQue} t1 {EECA} t1 {RAC} t1 {UA_INTLCK_CTRL} t2 {SWP} t1 {RAENP} t1 {UAAENP} t1 {EAENP} t1 {ATO} t1 {TAS} t1 {ATMPE} t1 {RWWP} t1 {SBLP (Supported Block Lengths and Protection)} t1 {Autoload Mode} t3 {Ready AEN Holdoff Period} i2 {Busy Timeout Period} i2 {Extended Self-Test Completion Time} i2 } 0x0a,0x01 "Control Extension" { {Reserved} *t4 {DLC} t1 {TCMOS} t1 {SCSIP} t1 {IALUAE} t1 {Reserved} *t4 {Initial Command Priority} t4 {Maximum Sense Data Length} i1 } 0x02 "Disconnect-Reconnect" { {Buffer Full Ratio} i1 {Buffer Empty Ratio} i1 {Bus Inactivity Limit} i2 {Disconnect Time Limit} i2 {Connect Time Limit} i2 {Maximum Burst Size} i2 {Reserved} *t6 {DTDC} t2 {Reserved} *i1 {Reserved} *i1 {Reserved} *i1 } 0x15 "Extended"; 0x16 "Extended Device-Type Specific"; 0x09 "Peripheral Device" { {Interface Identifier} i2 {Reserved} *i1 {Reserved} *i1 {Reserved} *i1 {Reserved} *i1 } 0x1a "Power Condition" { {PM_BG_PRECEDENCE} t1 {Reserved} *t6 {STANDBY_Y} t1 {Reserved} *t4 {IDLE_C} t1 {IDLE_B} t1 {IDLE_A} t1 {STANDBY_Z} t1 {IDLE_A Condition Timer} i4 {STANDBY_Z Condition Timer} i4 {IDLE_B Condition Timer} i4 {IDLE_C Condition Timer} i4 {STANDBY_Y Condition Timer} i4 {Reserved} *i4 {Reserved} *i4 {Reserved} *i4 {Reserved} *i3 {CCF Idle} t2 {CCF Standby} t2 {CCF Stopped} t2 {Reserved} *t2 } 0x1a,0x01 "Power Consumption" { {Reserved} *i2 {Reserved} *t6 {Active Level} t2 {Power Consumption Identifier} i1 {Reserved} *i4 {Reserved} *i4 } 0x18 "Protocol-Specific Logical Unit"; 0x19 "Protocol-Specific Port"; # DIRECT ACCESS DEVICES 0x0a,0x02 "Application Tag"; 0x1a,0xf1 "ATA Power Condition"; 0x1c,0x01 "Background Control" { {Reserved} *t5 {S_L_FULL} *t1 {LOWIR} *t1 {EN_BMS} *t1 {Reserved} *t7 {EN_PS} *t1 {Background Medium Scan Interval Time} i2 {Background Pre-Scan Time Limit} i2 {Minimum Idle Time Before Background Scan} i2 {Maximum Time To Suspend Background Scan} i2 {Reserved} *i2 } 0x0a,0x06 "Background Operation Control" { {BO_MODE} t2 {Reserved} *t6 } 0x08 "Caching" { {IC} t1 {ABPF} t1 {CAP} t1 {DISC} t1 {SIZE} t1 {WCE} t1 {MF} t1 {RCD} t1 {Demand Retention Priority} t4 {Write Retention Priority} t4 {Disable Pre-fetch Transfer Length} i2 {Minimum Pre-fetch} i2 {Maximum Pre-fetch} i2 {Maximum Pre-fetch Ceiling} i2 {FSW (Force Sequential Write)} t1 {LBCSS (Logical Block Cache Segment Size)} t1 {DRA (Disable Read-Ahead)} t1 {Vendor Specific} t2 {SYNC_PROG} t1 {NV_DIS} t1 {Number of Cache Segments} i1 {Cache Segment Size} i2 {Reserved} *t4 } 0x05 "Flexible Disk" { {Transfer rate} i2 {Number of heads} i1 {Sectors per track} i1 {Data bytes per sector} i2 {Number of cylinders} i2 {Starting cylinder-write precompensation} i2 {Starting cylinder-reduced write current} i2 {Drive step rate} i2 {Drive step pulse width} i1 {Head settle delay} i2 {Motor on delay} i1 {Motor off delay} i1 {TRDY} t1 {SSN} t1 {MO} t1 {Reserved} *t5 {Reserved} *t4 {SPC} t4 {Write Compensation} i1 {Head load delay} i1 {Head unload delay} i1 {Pin 34} t4 {Pin 2} t4 {Pin 4} t4 {Pin 1} t4 {Medium rotation rate} i2 {Reserved} *i1 {Reserved} *i1 } 0x03 "Format Device" { {Tracks per Zone} i2 {Alternate Sectors per Zone} i2 {Alternate Tracks per Zone} i2 {Alternate Tracks per Logical Unit} i2 {Sectors per Track} i2 {Data Bytes per Physical Sector} i2 {Interleave} i2 {Track Skew Factor} i2 {Cylinder Skew Factor} i2 {SSEC} t1 {HSEC} t1 {RMB} t1 {SURF} t1 {Reserved} *t4 } 0x0a,0x05 "I/O Advice Hints Grouping"; 0x1c "Informational Exceptions Control" { {PERF} t1 {Reserved} *t1 {EBF} t1 {EWasc} t1 {DExcpt} t1 {TEST} t1 {EBACKERR} t1 {LogErr} t1 {Reserved} *t4 {MRIE} t4 {Interval Timer} i4 {Report Count} i4 } 0x1c,0x02 "Logical Block Provisioning" { {Reserved} *t7 {SITUA} t1 {Reserved} *i1 {Reserved} *i1 {Reserved} *i1 {Reserved} *i4 {Reserved} *i4 } 0x0b "Medium Types Supported" { {Reserved} *i1 {Reserved} *i1 {Medium type one supported} i1 {Medium type two supported} i1 {Medium type three supported} i1 {Medium type four supported} i1 } 0x0c "Notch and Partition"; 0x0a,0xf1 "PATA Control"; 0x01 "Read-Write Error Recovery" { {AWRE (Auto Write Reallocation Enbld)} t1 {ARRE (Auto Read Reallocation Enbld)} t1 {TB (Transfer Block)} t1 {RC (Read Continuous)} t1 {EER (Enable Early Recovery)} t1 {PER (Post Error)} t1 {DTE (Disable Transfer on Error)} t1 {DCR (Disable Correction)} t1 {Read Retry Count} i1 {Correction Span} i1 {Head Offset Count} i1 {Data Strobe Offset Count} i1 {LBPERE (LBP Error Reporting Enabled)} t1 {MWR (Misaligned Write Reporting)} t2 {Reserved} *t5 {Write Retry Count} i1 {Reserved} *i1 {Recovery Time Limit} i2 } 0x04 "Rigid Disk Drive Geometry" { {Number of Cylinders} i3 {Number of Heads} i1 {Starting Cylinder-Write Precompensation} i3 {Starting Cylinder-Reduced Write Current} i3 {Drive Step Rate} i2 {Landing Zone Cylinder} i3 {Reserved} *t6 {RPL} t2 {Rotational Offset} i1 {Reserved} *i1 {Medium Rotation Rate} i2 {Reserved} *i1 {Reserved} *i1 } 0x07 "Verify Error Recovery" { {Reserved} *t4 {EER} t1 {PER} t1 {DTE} t1 {DCR} t1 {Verify Retry Count} i1 {Verify Correction Span} i1 {Reserved} *i1 {Reserved} *i1 {Reserved} *i1 {Reserved} *i1 {Reserved} *i1 {Verify Recovery Time Limit} i2 } 0x0E "CD-ROM Audio Control Parameters" { {Reserved} *t5 {Immed} t1 {SOTC} t1 {Reserved} *t1 {Reserved} *i2 {APRVal} t1 {Reserved} *t3 {Format of LBAs / sec.} t4 {Logical Blocks per Second of Audio Playback} i2 {Reserved} *t4 {Output Port 0 Channel Selection} t4 {Output Port 0 Volume} i1 {Reserved} *t4 {Output Port 1 Channel Selection} t4 {Output Port 1 Volume} i1 {Reserved} *t4 {Output Port 2 Channel Selection} t4 {Output Port 2 Volume} i1 {Reserved} *t4 {Output Port 3 Channel Selection} t4 {Output Port 3 Volume} i1 } # SEQUENTIAL ACCESS DEVICES 0x10 "Device Configuration" { {Reserved} *t1 {Change Active Partition} t1 {Change Active Format} t1 {Active Format} t5 {Active Partition} i1 {Write Buffer Full Ratio} i1 {Write Buffer Empty Ratio} i1 {Write Delay Time} i2 {Data Buffer Recovery} t1 {Block Identifiers Support} t1 {Report Setmarks} t1 {Automatic Velocity Control} t1 {Stop on Consecutive Filemarks} t2 {Recover Buffer Order} t1 {Report Early-Warning} t1 {Gap Size} i1 {EOD Defined} t3 {Enable EOD Generation} t1 {Synchronize at Early-Warning} t1 {Reserved} *t3 {Buffer Size at Early-Warning} i3 {Select Data Compression Algorithm} i1 {Reserved} *t5 {SCSI-3 Associated Write Protect} t1 {SCSI-3 Persistent Write Protect} t1 {SCSI-3 Permanent Write Protect} t1 } 0x0f "Data Compression" { {Data Compression Enabled} t1 {Date Compression Capable} t1 {Reserved} *t6 {Data Decompression Capable} t1 {Data Decompression Report on Exception} t2 {Reserved} *t5 {Compression Algorithm} i4 {Decompression Algorithm} i4 {Reserved} *i4 } # Removable devices 0x1b "Removable Block Access Capacities" { {System Floppy Type Device} t1 {Supports Reporting Format Progress} t1 {Reserved} *t6 {Non CD Optical Device} t1 {Single or Multiple LUN Supported} t1 {Reserved} *t3 {Total Logical Units Supported} t3 {Reserved} *i8 } # CD-ROM (and CD-R[W]) devices 0x2a "CD capabilities and mechanical status" { {Reserved} *t4 {Method 2} t1 {CD-RW Read} t1 {CD-R Read} t1 {Reserved} *t4 {Test Write} t1 {CD-RW Write} t1 {CD-R Write} t1 {Reserved} *t1 {Multi Session} t1 {Mode 2 Form 2} t1 {Mode 2 Form 1} t1 {Digital Port (2)} t1 {Digital Port (1)} t1 {Composite} t1 {Audio Play} t1 {Read Bar Code} t1 {UPC} t1 {ISRC} t1 {C2 Pointers are supported} t1 {R-W De-interleaved & corrected} t1 {R-W Supported} t1 {CD-DA Stream is Accurate} t1 {CD-DA Commands Supported} t1 {Loading Mechanism Type} t3 {Reserved} *t1 {Eject} t1 {Prevent Jumper} t1 {Lock State} t1 {Lock} t1 {Reserved} *t4 {S/W Slot Selection} t1 {Changer Supports Disc Present reporting} t1 {Separate Channel Mute Supported} t1 {Separate volume levels per channel} t1 {Maximum Read Speed Supported (kBps)} i2 {Number of Volume Leves Supported} i2 {Buffer Size supported by Drive (KB)} i2 {Current Read Speed Selected (kBps)} i2 {Reserved} *i1 {Reserved} *t2 {Length} t2 {LSBF} t1 {RCK} t1 {BCK} t1 {Reserved} *t1 {Maximum Write Speed Supported (kBps)} i2 {Current Write Speed Supported (kBps)} i2 }; 0x1d "Timeout and Protect" { {Reserved} *i2 {Reserved} *t4 {G3Enable} t1 {TMOE} t1 {DISP} t1 {SWPP} t1 {Reserved} *i1 {Group 1 Minimum Timeout} i2 {Group 2 Minimum Timeout} i2 {Group 3 Timeout} i2 }; 0x00 "Vendor-Specific";