# # Copyright (c) 2002-2008 Sam Leffler, Errno Consulting # All rights reserved. # # Redistribution and use in source and binary forms, with or without # modification, are permitted provided that the following conditions # are met: # 1. Redistributions of source code must retain the above copyright # notice, this list of conditions and the following disclaimer, # without modification. # 2. Redistributions in binary form must reproduce at minimum a disclaimer # similar to the "NO WARRANTY" disclaimer below ("Disclaimer") and any # redistribution must be conditioned upon including a substantially # similar Disclaimer requirement for further binary redistribution. # # NO WARRANTY # THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS # ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT # LIMITED TO, THE IMPLIED WARRANTIES OF NONINFRINGEMENT, MERCHANTIBILITY # AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL # THE COPYRIGHT HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, # OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF # SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS # INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER # IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) # ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF # THE POSSIBILITY OF SUCH DAMAGES. # # $FreeBSD: src/sys/modules/ath/Makefile,v 1.5.2.1.2.1 2009/04/15 03:14:26 kensmith Exp $ # ATH_RATE?= sample # tx rate control algorithm HAL=${.CURDIR}/ath_hal .PATH: ${HAL} KMOD= ath_hal #SRCS= if_ath.c if_ath_pci.c #SRCS = ah_osdep.c #SRCS += bus_if.h device_if.h pci_if.h opt_ah.h # NB: v3 eeprom support used by both AR5211 and AR5212; just include it SRCS= ah_osdep.c ah_osdep.h ah.c ah_regdomain.c ah_eeprom_v3.c SRCS+= device_if.h bus_if.h pci_if.h opt_inet.h opt_ath.h opt_ah.h # # AR5210 support; these are first generation 11a-only devices. # .PATH: ${HAL}/ar5210 .PATH: ${HAL} SRCS+= ah_eeprom_v1.c \ ar5210_attach.c ar5210_beacon.c ar5210_interrupts.c \ ar5210_keycache.c ar5210_misc.c ar5210_phy.c ar5210_power.c \ ar5210_recv.c ar5210_reset.c ar5210_xmit.c # # AR5211 support; these are second generation 11b/g/a devices # (but 11g was OFDM only and is not supported). # .PATH: ${HAL}/ar5211 SRCS+= ar5211_attach.c ar5211_beacon.c ar5211_interrupts.c \ ar5211_keycache.c ar5211_misc.c ar5211_phy.c ar5211_power.c \ ar5211_recv.c ar5211_reset.c ar5211_xmit.c # # AR5212 support; this covers all other pci/cardbus legacy parts. # .PATH: ${HAL}/ar5212 SRCS+= ar5212_ani.c ar5212_attach.c ar5212_beacon.c ar5212_eeprom.c \ ar5212_gpio.c ar5212_interrupts.c ar5212_keycache.c ar5212_misc.c \ ar5212_phy.c ar5212_power.c ar5212_recv.c ar5212_reset.c \ ar5212_rfgain.c ar5212_xmit.c # RF backends SRCS+= ar5111.c SRCS+= ar5112.c SRCS+= ar2413.c SRCS+= ar2425.c SRCS+= ar5413.c # # AR5416, AR9160 support; these are 11n parts but only really # supported (right now) operating in legacy mode. Note enabling # this support requires defining AH_SUPPORT_AR5416 in opt_ah.h # so the 11n tx/rx descriptor format is handled. # # NB: 9160 depends on 5416 but 5416 does not require 9160 # .PATH: ${HAL}/ar5416 SRCS+= ah_eeprom_v14.c \ ar5416_ani.c ar5416_attach.c ar5416_beacon.c ar5416_cal.c \ ar5416_cal_iq.c ar5416_cal_adcgain.c ar5416_cal_adcdc.c \ ar5416_eeprom.c ar5416_gpio.c ar5416_interrupts.c ar5416_keycache.c \ ar5416_misc.c ar5416_phy.c ar5416_power.c ar5416_recv.c \ ar5416_reset.c ar5416_xmit.c SRCS+= ar9160_attach.c # RF backend for 5416 and 9160 SRCS+= ar2133.c SRCS+= ar9280_attach.c # RF backend for 9280 SRCS+= ar9280.c SRCS+= ah_eeprom_v4k.c ar9285_reset.c ar9285_attach.c # RF backend for 9285 SRCS+= ar9285.c # NB: rate control is bound to the driver by symbol names so only pick one #.if ${ATH_RATE} == "sample" #.PATH: ${.CURDIR}/../../dev/ath/ath_rate/sample #SRCS+= sample.c opt_wlan.h #.elif ${ATH_RATE} == "onoe" #.PATH: ${.CURDIR}/../../dev/ath/ath_rate/onoe #SRCS+= onoe.c #.elif ${ATH_RATE} == "amrr" #.PATH: ${.CURDIR}/../../dev/ath/ath_rate/amrr #SRCS+= amrr.c #.endif CFLAGS+= -I. -I${HAL} .include