# # LINT64 -- config file for checking all the sources, tries to pull in # as much of the source tree as it can. # # $FreeBSD: src/sys/i386/conf/LINT,v 1.749.2.144 2003/06/04 17:56:59 sam Exp $ # # See the kernconf(5) manual page for more information on the format of # this file. # # NB: You probably don't want to try running a kernel built from this # file. Instead, you should start from X86_64_GENERIC, and add options # from this file as required. # # These directives are mandatory. The machine directive specifies the # platform and the machine_arch directive specifies the cpu architecture. # platform pc64 machine x86_64 machine_arch x86_64 # # This is the mandatory ``identification'' of the kernel. Usually this should # be the same as the name of your kernel. # ident LINT64 # # The `maxusers' parameter controls the static sizing of a number of # internal system tables by a formula defined in subr_param.c. Setting # maxusers to 0 will cause the system to auto-size based on physical # memory. # maxusers 10 # # The `makeoptions' parameter allows variables to be passed to the # generated Makefile in the build area. # # CONF_CFLAGS gives some extra compiler flags that are added to ${CFLAGS} # after most other flags. Here we use it to inhibit use of non-optimal # gcc builtin functions (e.g., memcmp). # # DEBUG happens to be magic. # The following is equivalent to 'config -g KERNELNAME' and creates # 'kernel.debug' compiled with -g debugging as well as a normal # 'kernel'. Use 'make install.debug' to install the debug kernel # but that isn't normally necessary as the debug symbols are not loaded # by the kernel and are not useful there anyway. # # KERNEL can be overridden so that you can change the default name of your # kernel. # # MODULES_OVERRIDE can be used to limit modules built to a specific list. # # INSTALLSTRIPPED can be set to cause installkernel to install stripped # kernels and modules rather than a kernel and modules with debug symbols. # # INSTALLSTRIPPEDMODULES can be set to allow a full debug kernel to be # installed, but to strip the installed modules. # makeoptions CONF_CFLAGS=-fno-builtin #Don't allow use of memcmp, etc. #makeoptions DEBUG=-g #Build kernel with gdb(1) debug symbols #makeoptions KERNEL=foo #Build kernel "foo" and install "/foo" # Only build those parts of the sound system I need. #makeoptions MODULES_OVERRIDE="sound/snd sound/pcm" #makeoptions INSTALLSTRIPPED=1 #makeoptions INSTALLSTRIPPEDMODULES=1 # # Certain applications can grow to be larger than the 128M limit # that DragonFly initially imposes. Below are some options to # allow that limit to grow to 256MB, and can be increased further # with changing the parameters. MAXDSIZ is the maximum that the # limit can be set to, and the DFLDSIZ is the default value for # the limit. MAXSSIZ is the maximum that the stack limit can be # set to. You might want to set the default lower than the max, # and explicitly set the maximum with a shell command for processes # that regularly exceed the limit like INND. # options MAXDSIZ="(256*1024*1024)" options MAXSSIZ="(256*1024*1024)" options DFLDSIZ="(256*1024*1024)" # # BLKDEV_IOSIZE sets the default block size used in user block # device I/O. Note that this value will be overridden by the label # when specifying a block device from a label with a non-0 # partition blocksize. The default is PAGE_SIZE. # options BLKDEV_IOSIZE=8192 # This allows you to actually store this configuration file into # the kernel binary itself, where it may be later read by saying: # strings -n 3 /kernel | sed -n 's/^___//p' > MYKERNEL # options INCLUDE_CONFIG_FILE # Include this file in kernel # # The root device and filesystem type can be compiled in; # this provides a fallback option if the root device cannot # be correctly guessed by the bootstrap code, or an override if # the RB_DFLTROOT flag (-r) is specified when booting the kernel. # options ROOTDEVNAME=\"ufs:da0s2e\" ##################################################################### # CPU OPTIONS # cpu is mandatory # cpu HAMMER_CPU # # Options for CPU features. # # CPU_DISABLE_AVX disables AVX instruction set. # options CPU_DISABLE_AVX # # These three options provide support for System V Interface # Definition-style interprocess communication, in the form of shared # memory, semaphores, and message queues, respectively. # # System V shared memory and tunable parameters options SHMMIN=2 # min shared memory segment size (bytes) options SHMMNI=33 # max number of shared memory identifiers options SHMSEG=9 # max shared memory segments per process # System V semaphores and tunable parameters options SEMMAP=31 # amount of entries in semaphore map options SEMMNI=11 # number of semaphore identifiers in the system options SEMMNS=61 # number of semaphores in the system options SEMMNU=31 # number of undo structures in the system options SEMMSL=61 # max number of semaphores per id options SEMOPM=101 # max number of operations per semop call options SEMUME=11 # max number of undo entries per process # System V message queues and tunable parameters options MSGMNB=2049 # max characters per message queue options MSGMNI=41 # max number of message queue identifiers options MSGSEG=2049 # max number of message segments in the system options MSGSSZ=16 # size of a message segment MUST be power of 2 options MSGTQL=41 # max amount of messages in the system ##################################################################### # DEBUGGING OPTIONS # # Enable the kernel debugger. # options DDB # # Print a stack trace on kernel panic. # options DDB_TRACE # # Don't drop into DDB for a panic. Intended for unattended operation # where you may want to drop to DDB from the console, but still want # the machine to recover from a panic # options DDB_UNATTENDED # # If using GDB remote mode to debug the kernel, there's a non-standard # extension to the remote protocol that can be used to use the serial # port as both the debugging port and the system console. It's non- # standard and you're on your own if you enable it. See also the # "remotechat" variables in the DragonFly specific version of gdb. # options GDB_REMOTE_CHAT # # KTRACE enables the system-call tracing facility ktrace(2). # options KTRACE #kernel tracing # # The INVARIANTS option is used in a number of source files to enable # extra sanity checking of internal structures. This support is not # enabled by default because of the extra time it would take to check # for these conditions, which can only occur as a result of # programming errors. # options INVARIANTS # # The DIAGNOSTIC option is used to enable extra debugging information # from some parts of the kernel. As this makes everything more noisy, # it is disabled by default. # options DIAGNOSTIC # # SYSCTL_DEBUG enables a 'sysctl' debug tree that can be used to dump the # contents of the registered sysctl nodes on the console. It is disabled by # default because it generates excessively verbose console output that can # interfere with serial console operation. # options SYSCTL_DEBUG # # NO_SYSCTL_DESCR prevents sysctl descriptions from being compiled in # #options NO_SYSCTL_DESCR # # This option let some drivers co-exist that can't co-exist in a running # system. This is used to be able to compile all kernel code in one go for # quality assurance purposes (like this file, which the option takes it name # from.) # options COMPILING_LINT # XXX - this doesn't belong here. # Allow ordinary users to take the console - this is useful for X. options UCONSOLE ##################################################################### # NETWORKING OPTIONS # # Protocol families: # Only the INET (Internet) family is officially supported in DragonFly. # options INET #Internet communications protocols options INET6 #IPv6 communications protocols options MPLS #Multi-Protocol Label Switching # # SMB/CIFS requester # NETSMB enables support for SMB protocol, it requires LIBMCHAIN and LIBICONV # options. options NETSMB #SMB/CIFS requester # mchain library. It can be either loaded as KLD or compiled into kernel options LIBMCHAIN #mbuf management library # netgraph(4). Enable the base netgraph code with the NETGRAPH option. # Individual node types can be enabled with the corresponding option # listed below; however, this is not strictly necessary as netgraph # will automatically load the corresponding KLD module if the node type # is not already compiled into the kernel. Each type below has a # corresponding man page, e.g., ng_async(4). options NETGRAPH #netgraph(4) system options NETGRAPH_ASYNC options NETGRAPH_BPF options NETGRAPH_BRIDGE options NETGRAPH_CISCO options NETGRAPH_ECHO options NETGRAPH_EIFACE options NETGRAPH_ETHER options NETGRAPH_FEC options NETGRAPH_FRAME_RELAY options NETGRAPH_HOLE options NETGRAPH_IFACE options NETGRAPH_KSOCKET options NETGRAPH_L2TP options NETGRAPH_LMI # MPPC compression requires proprietary files (not included) #options NETGRAPH_MPPC_COMPRESSION options NETGRAPH_MPPC_ENCRYPTION options NETGRAPH_ONE2MANY options NETGRAPH_PPP options NETGRAPH_PPPOE options NETGRAPH_PPTPGRE options NETGRAPH_RFC1490 options NETGRAPH_SOCKET options NETGRAPH_TEE options NETGRAPH_TTY options NETGRAPH_UI options NETGRAPH_VJC device mn # Munich32x/Falc54 Nx64kbit/sec cards. # # Network interfaces: # The `loop' pseudo-device is MANDATORY when networking is enabled. # The `ether' pseudo-device provides generic code to handle # Ethernets; it is MANDATORY when an Ethernet device driver is # configured. # The `sppp' pseudo-device serves a similar role for certain types # of synchronous PPP links. # The `sl' pseudo-device implements the Serial Line IP (SLIP) service. # The `bpf' pseudo-device enables the Berkeley Packet Filter. Be # aware of the legal and administrative consequences of enabling this # option. The number of devices determines the maximum number of # simultaneous BPF clients programs runnable. # The `disc' pseudo-device implements a minimal network interface, # which throws away all packets sent and never receives any. It is # included for testing purposes. This shows up as the 'ds' interface. # The `tun' pseudo-device implements (user-)ppp and nos-tun # The `gif' pseudo-device implements IPv6 over IP4 tunneling, # IPv4 over IPv6 tunneling, IPv4 over IPv4 tunneling and # IPv6 over IPv6 tunneling. # The `gre' device implements two types of IP4 over IP4 tunneling: # GRE and MOBILE, as specified in the RFC1701 and RFC2004. # The `stf' device implements 6to4 encapsulation. # The `ef' pseudo-device provides support for multiple ethernet frame types # specified via ETHER_* options. See ef(4) for details. # pseudo-device ether #Generic Ethernet pseudo-device vlan 1 #VLAN support pseudo-device bridge #Bridging support pseudo-device sppp #Generic Synchronous PPP pseudo-device loop #Network loopback device pseudo-device bpf #Berkeley packet filter pseudo-device disc #Discard device (ds0, ds1, etc) pseudo-device tap #Ethernet tunnel network interface pseudo-device tun #Tunnel driver (ppp(8), nos-tun(8)) pseudo-device sl 2 #Serial Line IP pseudo-device gre #IP over IP tunneling pseudo-device wg # WireGuard VPN # for IPv6 pseudo-device gif #IPv6 and IPv4 tunneling pseudo-device stf #6to4 IPv6 over IPv4 encapsulation # NetBSD Virtual Machine Monitor pseudo-device nvmm # # Internet family options: # # MROUTING enables the kernel multicast packet forwarder, which works # with mrouted(8) (from dports). # # PIM enables Protocol Independent Multicast in the kernel. # Requires MROUTING enabled. # # IPFIREWALL enables support for IP firewall construction, in # conjunction with the `ipfw' program. IPFIREWALL_VERBOSE sends # logged packets to the system logger. IPFIREWALL_VERBOSE_LIMIT # limits the number of times a matching entry can be logged. # # WARNING: IPFIREWALL defaults to a policy of "deny ip from any to any" # and if you do not add other rules during startup to allow access, # YOU WILL LOCK YOURSELF OUT. It is suggested that you set firewall_type=open # in /etc/rc.conf when first enabling this feature, then refining the # firewall rules in /etc/rc.firewall after you've tested that the new kernel # feature works properly. # # IPFIREWALL3 is based on a newer version of FreeBSD's ipfw2, along with # some enhancements. See ipfw3(4). # # IPFIREWALL_DEFAULT_TO_ACCEPT causes the default rule (at boot) to # allow everything. Use with care, if a cracker can crash your # firewall machine, they can get to your protected machines. However, # if you are using it as an as-needed filter for specific problems as # they arise, then this may be for you. Changing the default to 'allow' # means that you won't get stuck if the kernel and /sbin/ipfw binary get # out of sync. # # IPDIVERT enables the divert IP sockets, used by ``ipfw divert'' # # IPSTEALTH enables code to support stealth forwarding (i.e., forwarding # packets without touching the ttl). This can be useful to hide firewalls # from traceroute and similar tools. # # TCPDEBUG is undocumented. # # ICMPPRINTFS enables ICMP to do extra debug prints. # options MROUTING # Multicast routing options PIM # Protocol Independent Multicast options IPFIREWALL #firewall options IPFIREWALL_DEBUG #debug prints options IPFIREWALL_VERBOSE #enable logging to syslogd(8) options IPFIREWALL_VERBOSE_LIMIT=100 #limit verbosity options IPFIREWALL_DEFAULT_TO_ACCEPT #allow everything by default options IPV6FIREWALL #firewall for IPv6 options IPV6FIREWALL_VERBOSE options IPV6FIREWALL_VERBOSE_LIMIT=100 options IPV6FIREWALL_DEFAULT_TO_ACCEPT options IPDIVERT #divert sockets options IPSTEALTH #support for stealth forwarding options TCPDEBUG options ICMPPRINTFS options IPFIREWALL3 device pf device pflog #CARP pseudo-device carp options CARP # Link aggregation interface. pseudo-device lagg # The MBUF_STRESS_TEST option enables options which create # various random failures / extreme cases related to mbuf # functions. See the mbuf(9) manpage for a list of available # test cases. options MBUF_STRESS_TEST # Statically link in accept filters options ACCEPT_FILTER_DATA options ACCEPT_FILTER_HTTP # TCP_SIGNATURE adds support for RFC 2385 (TCP-MD5) digests. These are # carried in TCP option 19. # This is enabled on a per-socket basis using the TCP_SIGNATURE_ENABLE # socket option. # This requires the use of 'device crypto' or 'device cryptodev'. # # XXX disabled for now until building with it is fixed, which broke # after removing IPsec. # #options TCP_SIGNATURE #include support for RFC 2385 # # TCP_DROP_SYNFIN adds support for ignoring TCP packets with SYN+FIN. This # prevents nmap et al. from identifying the TCP/IP stack, but breaks support # for RFC1644 extensions and is not recommended for web servers. # options TCP_DROP_SYNFIN #drop TCP packets with SYN+FIN # ICMP_BANDLIM enables icmp error response bandwidth limiting. You # typically want this option as it will help protect the machine from # D.O.S. packet attacks. # options ICMP_BANDLIM # DUMMYNET enables the "dummynet" bandwidth limiter. You need # IPFIREWALL as well. See the dummynet(4) and ipfw(8) manpages for more info. # options DUMMYNET options DUMMYNET_DEBUG # IFPOLL_ENABLE adds support for mixed interrupt-polling handling # of network device drivers, which has significant benefits in terms # of robustness to overloads and responsivity, as well as permitting # accurate scheduling of the CPU time between kernel network processing # and other activities. The drawback is a moderate (up to 1/pollhz seconds) # potential increase in response times. See polling(4) for further details. # # IFPOLL_ENABLE adds hardware queues' based polling options IFPOLL_ENABLE ##################################################################### # FILESYSTEM OPTIONS # # Only the root, /usr, and /tmp filesystems need be statically # compiled; everything else will be automatically loaded at mount # time. (Exception: the UFS family --- FFS, and MFS --- # cannot currently be demand-loaded.) Some people still prefer # to statically compile other filesystems as well. # # One of these is mandatory: options FFS #Fast filesystem options MFS #Memory filesystem options NFS #Network filesystem # The rest are optional: #options NFS_NOSERVER #Disable the NFS-server code. options AUTOFS #Automounter filesystem options CD9660 #ISO 9660 filesystem options FUSE #FUSE support module options HAMMER #HAMMER filesystem options HAMMER2 #HAMMER2 filesystem options HPFS #OS/2 File system options MSDOSFS #MS DOS filesystem options NTFS #NT filesystem options NULLFS #NULL filesystem options PROCFS #Process filesystem options SMBFS #SMB/CIFS filesystem options TMPFS #Temporary filesystem options UDF #UDF filesystem # The xFS_ROOT options REQUIRE the associated ``options xFS'' options NFS_ROOT #NFS usable as root device # Soft updates is technique for improving UFS filesystem speed and # making abrupt shutdown less risky. options SOFTUPDATES # Directory hashing improves the speed of operations on very large # directories at the expense of some memory. options UFS_DIRHASH # Make space in the kernel for a root filesystem on a md device. # Define to the number of kilobytes to reserve for the filesystem. options MD_ROOT_SIZE=10 # Make the md device a potential root device, either with preloaded # images of type mfs_root or md_root. options MD_ROOT # Specify double the default maximum size for malloc(9)-backed md devices. options MD_NSECT=40000 # Allow this many swap-devices. # # In order to manage swap, the system must reserve bitmap space that # scales with the largest mounted swap device multiplied by NSWAPDEV, # regardless of whether other swap devices exist or not. So it # is not a good idea to make this value too large. options NSWAPDEV=5 # Disk quotas are supported when this option is enabled. options QUOTA #enable disk quotas # If you are running a machine just as a fileserver for PC and MAC # users, e.g. using SAMBA, you may consider setting this option # and keeping all those users' directories on a filesystem that is # mounted with the suiddir option. This gives new files the same # ownership as the directory (similar to group). It's a security hole # if you let these users run programs, so confine it to file-servers # (but it'll save you lots of headaches in those cases). Root owned # directories are exempt and X bits are cleared. The suid bit must be # set on the directory as well; see chmod(1) PC owners can't see/set # ownerships so they keep getting their toes trodden on. This saves # you all the support calls as the filesystem it's used on will act as # they expect: "It's my dir so it must be my file". # options SUIDDIR # NFS options: options NFS_MINATTRTIMO=3 # VREG attrib cache timeout in sec options NFS_MAXATTRTIMO=60 options NFS_MINDIRATTRTIMO=30 # VDIR attrib cache timeout in sec options NFS_MAXDIRATTRTIMO=60 options NFS_GATHERDELAY=10 # Default write gather delay (msec) options NFS_UIDHASHSIZ=29 # Tune the size of nfssvc_sock with this options NFS_WDELAYHASHSIZ=16 # and with this options NFS_MUIDHASHSIZ=63 # Tune the size of nfsmount with this options NFS_DEBUG # Enable NFS Debugging # NTFS options: options NTFS_DEBUG # MSDOSFS options: options MSDOSFS_DEBUG # Enable MSDOSFS Debugging # # Add support for the EXT2FS filesystem of Linux fame. Be a bit # careful with this - the ext2fs code has a tendency to lag behind # changes and not be exercised very much, so mounting read/write could # be dangerous (and even mounting read only could result in panics.) # options EXT2FS # Optional character code conversion support with LIBICONV. # Each option requires their base file system and LIBICONV. options CD9660_ICONV options MSDOSFS_ICONV options NTFS_ICONV ##################################################################### # POSIX P1003.1B # Real time extensions added in the 1993 Posix # _KPOSIX_PRIORITY_SCHEDULING: Build in _POSIX_PRIORITY_SCHEDULING options _KPOSIX_PRIORITY_SCHEDULING ##################################################################### # CLOCK OPTIONS # The granularity of operation is controlled by the kernel option HZ_DEFAULT # whose default value (100) means a granularity of 10ms (1s/HZ_DEFAULT). # Consider, however, that reducing the granularity too much might # cause excessive overhead in clock interrupt processing, # potentially causing ticks to be missed and thus actually reducing # the accuracy of operation. options HZ_DEFAULT=100 ##################################################################### # SCSI DEVICES # SCSI DEVICE CONFIGURATION # The SCSI subsystem consists of the `base' SCSI code, a number of # high-level SCSI device `type' drivers, and the low-level host-adapter # device drivers. The host adapters are listed in the ISA and PCI # device configuration sections below. # # Beginning with FreeBSD 2.0.5 you can wire down your SCSI devices so # that a given bus, target, and LUN always come on line as the same # device unit. In earlier versions the unit numbers were assigned # in the order that the devices were probed on the SCSI bus. This # means that if you removed a disk drive, you may have had to rewrite # your /etc/fstab file, and also that you had to be careful when adding # a new disk as it may have been probed earlier and moved your device # configuration around. # This old behavior is maintained as the default behavior. The unit # assignment begins with the first non-wired down unit for a device # type. For example, if you wire a disk as "da3" then the first # non-wired disk will be assigned da4. # The syntax for wiring down devices is: # device scbus0 at ahc0 # Single bus device # device scbus1 at ahc1 bus 0 # Single bus device # device scbus3 at ahc2 bus 0 # Twin bus device # device scbus2 at ahc2 bus 1 # Twin bus device # device da0 at scbus0 target 0 unit 0 # device da1 at scbus3 target 1 # device da2 at scbus2 target 3 # device sa1 at scbus1 target 6 # device cd # "units" (SCSI logical unit number) that are not specified are # treated as if specified as LUN 0. # All SCSI devices allocate as many units as are required. # The "unknown" device (uk? in pre-2.0.5) is now part of the base SCSI # configuration and doesn't have to be explicitly configured. device scbus #base SCSI code device ch #SCSI media changers device da #SCSI direct access devices (aka disks) device sa #SCSI tapes device cd #SCSI CD-ROMs device pass #CAM passthrough driver device sg #Passthrough device (linux scsi generic) device pt #SCSI processor type device ses #SCSI SES/SAF-TE driver device targ #SCSI Target Mode Code device targbh #SCSI Target Mode Blackhole Device # Options for device mapper device dm device dm_target_crypt device dm_target_linear device dm_target_striped device dm_target_delay device dm_target_flakey # Options for iSCSI device iscsi_initiator options ISCSI_INITIATOR_DEBUG=8 # CAM OPTIONS: # debugging options: # -- NOTE -- If you specify one of the bus/target/lun options, you must # specify them all! # CAMDEBUG: When defined enables debugging macros # CAM_DEBUG_BUS: Debug the given bus. Use -1 to debug all busses. # CAM_DEBUG_TARGET: Debug the given target. Use -1 to debug all targets. # CAM_DEBUG_LUN: Debug the given lun. Use -1 to debug all luns. # CAM_DEBUG_FLAGS: OR together CAM_DEBUG_INFO, CAM_DEBUG_TRACE, # CAM_DEBUG_SUBTRACE, and CAM_DEBUG_CDB # # CAM_MAX_HIGHPOWER: Maximum number of concurrent high power (start unit) cmds # SCSI_NO_SENSE_STRINGS: When defined disables sense descriptions # SCSI_NO_OP_STRINGS: When defined disables opcode descriptions # SCSI_DELAY: The number of MILLISECONDS to freeze the SIM (scsi adapter) # queue after a bus reset, and the number of milliseconds to # freeze the device queue after a bus device reset. This # can be changed at boot and runtime with the # kern.cam.scsi_delay tunable/sysctl. options CAMDEBUG options CAM_DEBUG_BUS=-1 options CAM_DEBUG_TARGET=-1 options CAM_DEBUG_LUN=-1 options CAM_DEBUG_FLAGS="CAM_DEBUG_INFO|CAM_DEBUG_TRACE|CAM_DEBUG_CDB" options CAM_MAX_HIGHPOWER=4 options SCSI_NO_SENSE_STRINGS options SCSI_NO_OP_STRINGS options SCSI_DELAY=8000 # Be pessimistic about Joe SCSI device # Options for the CAM CDROM driver: # CHANGER_MIN_BUSY_SECONDS: Guaranteed minimum time quantum for a changer LUN # CHANGER_MAX_BUSY_SECONDS: Maximum time quantum per changer LUN, only # enforced if there is I/O waiting for another LUN # The compiled in defaults for these variables are 2 and 10 seconds, # respectively. # # These can also be changed on the fly with the following sysctl variables: # kern.cam.cd.changer.min_busy_seconds # kern.cam.cd.changer.max_busy_seconds # options CHANGER_MIN_BUSY_SECONDS=2 options CHANGER_MAX_BUSY_SECONDS=10 # Options for the CAM sequential access driver: # SA_IO_TIMEOUT: Timeout for read/write/wfm operations, in minutes # SA_SPACE_TIMEOUT: Timeout for space operations, in minutes # SA_REWIND_TIMEOUT: Timeout for rewind operations, in minutes # SA_ERASE_TIMEOUT: Timeout for erase operations, in minutes # SA_1FM_AT_EOD: Default to model which only has a default one filemark at EOT. options SA_IO_TIMEOUT="(4)" options SA_SPACE_TIMEOUT="(60)" options SA_REWIND_TIMEOUT="(2*60)" options SA_ERASE_TIMEOUT="(4*60)" options SA_1FM_AT_EOD # Optional timeout for the CAM processor target (pt) device # This is specified in seconds. The default is 60 seconds. options SCSI_PT_DEFAULT_TIMEOUT="60" # Optional enable of doing SES passthrough on other devices (e.g., disks) # # Normally disabled because a lot of newer SCSI disks report themselves # as having SES capabilities, but this can then clot up attempts to build # build a topology with the SES device that's on the box these drives # are in.... options SES_ENABLE_PASSTHROUGH ##################################################################### # MISCELLANEOUS DEVICES AND OPTIONS # The `pty' device usually turns out to be ``effectively mandatory'', # as it is required for `telnetd', `rlogind', `screen', `emacs', and # `xterm', among others. pseudo-device pty # Pseudo ttys pseudo-device md # Memory/malloc disk pseudo-device vn # File image "disks" pseudo-device snp # Snoop device - to look at pty/vty/etc.. pseudo-device ccd 4 # Concatenated disk driver # Configuring Vinum into the kernel is not necessary, since the kld # module gets started automatically when vinum(8) starts. This # device is also untested. Use at your own risk. # # The option VINUMDEBUG must match the value set in CFLAGS # in src/sbin/vinum/Makefile. Failure to do so will result in # the following message from vinum(8): # # Can't get vinum config: Invalid argument # # see vinum(4) for more reasons not to use these options. pseudo-device vinum #Vinum concat/mirror/raid driver options VINUMDEBUG #enable Vinum debugging hooks # Kernel side iconv library options LIBICONV # Size of the kernel message buffer. Should be N * pagesize. options MSGBUF_SIZE=40960 ##################################################################### # HARDWARE DEVICE CONFIGURATION # ISA devices: # # Mandatory ISA devices: isa # device isa # # Options for `isa': # # AUTO_EOI_1 enables the `automatic EOI' feature for the master 8259A # interrupt controller. This saves about 0.7-1.25 usec for each interrupt. # This option breaks suspend/resume on some portables. # # AUTO_EOI_2 enables the `automatic EOI' feature for the slave 8259A # interrupt controller. This saves about 0.7-1.25 usec for each interrupt. # Automatic EOI is documented not to work for the slave with the # original i8259A, but it works for some clones and some integrated # versions. # # MAXMEM specifies the amount of RAM on the machine; if this is not # specified, DragonFly will first read the amount of memory from the CMOS # RAM, so the amount of memory will initially be limited to 64MB or 16MB # depending on the BIOS. If the BIOS reports 64MB, a memory probe will # then attempt to detect the installed amount of RAM. If this probe # fails to detect >64MB RAM you will have to use the MAXMEM option. # The amount is in kilobytes, so for a machine with 128MB of RAM, it would # be 131072 (128 * 1024). # # BROKEN_KEYBOARD_RESET disables the use of the keyboard controller to # reset the CPU for reboot. This is needed on some systems with broken # keyboard controllers. options AUTO_EOI_1 #options AUTO_EOI_2 options MAXMEM="(128*1024)" #options BROKEN_KEYBOARD_RESET # Enable support for the kernel PLL to use an external PPS signal, # under supervision of [x]ntpd(8) # More info in ntpd documentation: http://www.eecis.udel.edu/~ntp options PPS_SYNC # The keyboard controller; it controls the keyboard and the PS/2 mouse. device atkbdc0 at isa? port IO_KBD # The AT keyboard device atkbd0 at atkbdc? irq 1 # Options for atkbd: options ATKBD_DFLT_KEYMAP # specify the built-in keymap makeoptions ATKBD_DFLT_KEYMAP="jp.106" # These options are valid for other keyboard drivers as well. options KBD_DISABLE_KEYMAP_LOAD # refuse to load a keymap options KBD_INSTALL_CDEV # install a CDEV entry in /dev # `flags' for atkbd: # 0x01 Force detection of keyboard, else we always assume a keyboard # 0x02 Don't reset keyboard, useful for some newer ThinkPads # 0x03 Force detection and avoid reset, might help with certain # dockingstations # 0x04 Old-style (XT) keyboard support, useful for older ThinkPads # PS/2 mouse device psm0 at atkbdc? irq 12 # Options for psm: options PSM_HOOKRESUME #hook the system resume event, useful #for some laptops options PSM_RESETAFTERSUSPEND #reset the device at the resume event device kbdmux # keyboard multiplexer # The video card driver. device vga0 at isa? # Options for vga: options VGA_DEBUG=2 # enable VGA debug output # If you experience problems switching back to 80x25 (or a derived mode), # the following option might help. #options VGA_KEEP_POWERON_MODE # use power-on settings for 80x25 # If you can dispense with some vga driver features, you may want to # use the following options to save some memory. #options VGA_NO_FONT_LOADING # don't save/load font #options VGA_NO_MODE_CHANGE # don't change video modes # The following option probably won't work with the LCD displays. options VGA_WIDTH90 # support 90 column modes # Splash screen at start up! Screen savers require this too. pseudo-device splash # The syscons console driver (sco color console compatible). device sc0 at nexus? options MAXCONS=16 # number of virtual consoles options SC_ALT_MOUSE_IMAGE # simplified mouse cursor in text mode options SC_DEBUG_LEVEL=5 # enable debug output options SC_DFLT_FONT # compile font in makeoptions SC_DFLT_FONT=cp850 options SC_DISABLE_DDBKEY # disable `debug' key options SC_DISABLE_REBOOT # disable reboot key sequence options SC_HISTORY_SIZE=200 # number of history buffer lines options SC_MOUSE_CHAR=0x3 # char code for text mode mouse cursor options SC_PIXEL_MODE # add support for the raster text mode # The following options will let you change the default colors of syscons. options SC_NORM_ATTR="(FG_GREEN|BG_BLACK)" options SC_NORM_REV_ATTR="(FG_YELLOW|BG_GREEN)" options SC_KERNEL_CONS_ATTR="(FG_RED|BG_BLACK)" options SC_KERNEL_CONS_REV_ATTR="(FG_BLACK|BG_RED)" options SC_BORDER_COLOR="FG_BLACK" # If you have a two button mouse, you may want to add the following option # to use the right button of the mouse to paste text. options SC_TWOBUTTON_MOUSE # You can selectively disable features in syscons. #options SC_NO_CUTPASTE #options SC_NO_FONT_LOADING #options SC_NO_HISTORY #options SC_NO_SYSMOUSE # # SCSI host adapters # # adv: All Narrow SCSI bus AdvanSys controllers. # adw: Second Generation AdvanSys controllers including the ADV940UW. # bt: Most Buslogic controllers # # Note that the order is important in order for Buslogic cards to be # probed correctly. # device bt device adv device adw # # Adaptec FSA RAID controllers, including integrated DELL controller, # the Dell PERC 2/QC and the HP NetRAID-4M # device aac options AAC_DEBUG device aacp # SCSI Passthrough interface (optional, CAM required) # # Compaq Smart RAID, Mylex DAC960 and AMI MegaRAID controllers. Only # one entry is needed; the code will find and configure all supported # controllers. # device ida # Compaq Smart RAID device mlx # Mylex DAC960 device amr # AMI MegaRAID device amrp # SCSI Passthrough interface (optional, CAM req.) options AMR_DEBUG=3 device mfi # LSI MegaRAID SAS device mfip # LSI MegaRAID SAS passthrough, requires CAM options MFI_DEBUG # # LSI MegaRAID 6Gb/s and 12Gb/s SAS+SATA RAID controller driver # device mrsas # # Areca RAID (CAM is required). # device arcmsr # Areca SATA II RAID # # Highpoint RocketRAID 182x. device hptmv # # Highpoint RocketRAID. Supports RR172x, RR222x, RR2240, RR232x, RR2340, # RR2210, RR174x, RR2522, RR231x, RR230x. device hptrr # # Highpoint RocketRAID 27xx. device "hpt27xx" # # Highpoint RocketRaid 3xxx series SATA RAID device hptiop # # 3ware ATA RAID # device twe # 3ware ATA RAID device twa # 3ware 9000 series PATA/SATA RAID options TWA_DEBUG=10 # enable debug messages device tws # 3ware 9750 series SATA/SAS RAID # # IBM ServeRAID # device ips # AHCI driver, this will override NATA for AHCI devices, # both drivers may be included. # device ahci # NVME driver # device nvme # SiI3124/3132 driver # device sili # Network controlled disks # device xdisk # The 'NATA' driver supports all ATA and ATAPI devices. # You only need one "device nata" for it to find all # PCI ATA/ATAPI devices on modern machines. # device nata device natadisk # ATA disk drives device natapicd # ATAPI CD/DVD drives device natapifd # ATAPI floppy drives device natapist # ATAPI tape drives device natapicam # ATAPI CAM layer emulation device nataraid # support for ATA software RAID controllers # The following options are valid for the NATA driver: # # ATA_STATIC_ID: controller numbering is static (like the old driver) # else the device numbers are dynamically allocated. # ATA_NO_*: leave out support for the specified controller brand # options ATA_STATIC_ID #options ATA_NO_ACARD #options ATA_NO_ACERLABS #options ATA_NO_AHCI #options ATA_NO_AMD #options ATA_NO_CYPRESS #options ATA_NO_CYRIX #options ATA_NO_HIGHPOINT #options ATA_NO_INTEL #options ATA_NO_ITE #options ATA_NO_JMICRON #options ATA_NO_MARVELL #options ATA_NO_NATIONAL #options ATA_NO_NETCELL #options ATA_NO_NVIDIA #options ATA_NO_PROMISE #options ATA_NO_SERVERWORKS #options ATA_NO_SILICONIMAGE #options ATA_NO_SIS #options ATA_NO_VIA # For older non-PCI systems, these are the lines to use: # #device nata0 at isa? port IO_WD1 irq 14 #device nata1 at isa? port IO_WD2 irq 15 # # Standard floppy disk controllers: `fdc' and `fd' (see fdc(4)) # device fdc0 at isa? port IO_FD1 irq 6 drq 2 # # FDC_DEBUG enables floppy debugging. Since the debug output is huge, you # gotta turn it actually on by setting the variable fd_debug with DDB, # however. options FDC_DEBUG device fd0 at fdc0 drive 0 device fd1 at fdc0 drive 1 # LMC/SBE LMC1504 quad T1/E1 driver # device musycc # # sio: serial ports (see sio(4)) device sio0 at isa? port IO_COM1 flags 0x10 irq 4 # # `flags' for serial drivers that support consoles (only for sio now): # 0x10 enable console support for this unit. The other console flags # are ignored unless this is set. Enabling console support does # not make the unit the preferred console - boot with -h or set # the 0x20 flag for that. Currently, at most one unit can have # console support; the first one (in config file order) with # this flag set is preferred. Setting this flag for sio0 gives # the old behaviour. # 0x20 force this unit to be the console (unless there is another # higher priority console). This replaces the COMCONSOLE option. # 0x40 reserve this unit for low level console operations. Do not # access the device in any normal way. # 0x80 use this port for serial line gdb support in ddb. # # Options for serial drivers that support consoles (only for sio now): options BREAK_TO_DEBUGGER #a BREAK on a comconsole goes to #DDB, if available. options CONSPEED=115200 # speed for serial console # (default 9600) # Solaris implements a new BREAK which is initiated by a character # sequence CR ~ ^b which is similar to a familiar pattern used on # Sun servers by the Remote Console. options ALT_BREAK_TO_DEBUGGER # Options for sio: options COM_ESP #code for Hayes ESP options COM_MULTIPORT #code for some cards with shared IRQs # Other flags for sio that aren't documented in the man page. # 0x20000 enable hardware RTS/CTS and larger FIFOs. Only works for # ST16650A-compatible UARTs. # PCI Universal Communications driver # Supports various single and multi port PCI serial cards. Maybe later # also the parallel ports on combination serial/parallel cards. New cards # can be added in src/sys/dev/misc/puc/pucdata.c. device puc # # Network interfaces: `is', `lnc' # # lnc: Lance/PCnet cards (Isolan, Novell NE2100, NE32-VL, AMD Am7990 & Am79C960) # sbsh: Granch SBNI16 SHDSL modem PCI adapters # vmx: VMware VMXNET3 Ethernet (BSD open source) # wi: Lucent WaveLAN/IEEE 802.11 PCMCIA adapters. Note: this supports both # the PCMCIA and ISA cards: the ISA card is really a PCMCIA to ISA # bridge with a PCMCIA adapter plugged into it. # xe: Xircom/Intel EtherExpress Pro100/16 PC Card ethernet controller. # device lnc device sln device sn # Wlan support is mandatory for some wireless LAN devices. options IEEE80211_DEBUG #enable debugging msgs options IEEE80211_SUPPORT_MESH #enable 802.11s D3.0 support options IEEE80211_SUPPORT_TDMA #enable TDMA support device wlan # 802.11 support device wlan_acl # 802.11 MAC-based access control for AP device wlan_ccmp # 802.11 CCMP support device wlan_tkip # 802.11 TKIP support device wlan_wep # 802.11 WEP support device wlan_xauth # 802.11 WPA or 802.1x authentication for AP device wlan_amrr # 802.11 AMRR TX rate control algorithm device ath # Atheros AR521x options AH_AR5416_INTERRUPT_MITIGATION options AH_ASSERT options AH_DEBUG options AH_INTERRUPT_DEBUGGING options AH_MAXCHAN=96 options AH_NEED_DESC_SWAP options AH_PRIVATE_DIAG options AH_RXCFG_SDMAMW_4BYTES options AH_SUPPORT_AR5416 options AH_SUPPORT_AR9130 options AH_SUPPORT_AR9330 options AH_SUPPORT_AR9340 options AH_USE_INIPDGAIN device ath_hal # Atheros Hardware Access Layer #device ath_rate_amrr # Atheros AMRR TX rate control algorithm #device ath_rate_onoe # Atheros Onoe TX rate control algorithm device ath_rate_sample # Atheros Sample TX rate control algorithm options ATH_DEBUG # turn on debugging output (see hw.ath.debug) options ATH_DIAGAPI # diagnostic interface to the HAL options ATH_ENABLE_DFS options ATH_KTR_INTR_DEBUG device siba_bwn # Sonic Inc. Silicon Backplane needed for bwn options SIBA_DEBUG # turn on debugging output device bwn # Broadcom BCM43xx NICs using v4 firmware options BWN_DEBUG # turn on debugging output options BWN_RXRING_SLOTS=128 # number of RX slots to allocate options BWN_TXRING_SLOTS=128 # number of TX slots to allocate device iwi # Intel PRO/Wireless 2200BG/2915ABG device iwm # Intel Dual Band Wireless AC 316x/726x/826x options IWM_DEBUG # turn on debugging output device iwn # Intel WiFi Link 4965/1000/5000/5150/5300/6000/6050 options IWN_DEBUG # turn on debugging output device wi # WaveLAN/IEEE, PRISM-II, Spectrum24 802.11DS device xe # Xircom PCMCIA device ral # Ralink Technology 802.11 wireless NIC device wpi options WPI_DEBUG # turn on debugging output # IEEE 802.11 adapter firmware modules # iwifw: Intel PRO/Wireless 2200BG/2225BG/2915ABG firmware # iwmfw Intel Dual Band Wireless AC 3160/3165/3168/7260/7265/8260/8265 # iwnfw: Intel WiFi Link 4965/1000/5000/5150/5300/6000/6050 # ralfw: Ralink Technology RT25xx and RT26xx firmware # wpifw: Intel 3945ABG Wireless LAN Controller firmware device iwifw device iwmfw device iwnfw device ralfw device wpifw # Bluetooth Protocols device bluetooth # Sound drivers # # Basic sound card support: device sound # For PCI sound cards: device "snd_als4000" device "snd_atiixp" device "snd_cmi" device "snd_cs4281" device "snd_emu10k1" device "snd_emu10kx" device "snd_envy24" device "snd_envy24ht" device "snd_es137x" device "snd_fm801" device "snd_hda" device "snd_hdspe" device "snd_ich" device "snd_maestro" device "snd_neomagic" device "snd_solo" device "snd_spicds" device "snd_t4dwave" device "snd_via8233" device "snd_via82c686" device "snd_vibes" # USB device "snd_uaudio" # # Following options are intended for debugging/testing purposes: # # SND_DEBUG Enable extra debugging code that includes # sanity checking and possible increase of # verbosity. # # SND_DIAGNOSTIC Similar in a spirit of INVARIANTS/DIAGNOSTIC, # zero tolerance against inconsistencies. # # SND_FEEDER_MULTIFORMAT By default, only 16/32 bit feeders are compiled # in. This options enable most feeder converters # except for 8bit. WARNING: May bloat the kernel. # # SND_FEEDER_FULL_MULTIFORMAT Ditto, but includes 8bit feeders as well. # # SND_FEEDER_RATE_HP (feeder_rate) High precision 64bit arithmetic # as much as possible (the default trying to # avoid it). Possible slowdown. # # SND_OLDSTEREO Only 2 channels are allowed, effectively # disabling multichannel processing. # options SND_DEBUG #options SND_DIAGNOSTIC options SND_FEEDER_MULTIFORMAT options SND_FEEDER_FULL_MULTIFORMAT options SND_FEEDER_RATE_HP options SND_OLDSTEREO # # Miscellaneous hardware: # # bktr: Brooktree bt848/848a/849a/878/879 video capture and TV Tuner board # coremctl: Intel Core/E3 memory controller (required by ecc(4) and memtemp(4)) # dimm: Location inforamtion (required by ecc(4) and memtemp(4)) # ecc: ECC memory controller # ipmi: Intelligent Platform Management Interface # joy: joystick # nmdm: nullmodem terminal driver (see nmdm(4)) # tpm: Trusted Platform Module # Notes on the Specialix SI/XIO driver: # **This is NOT a Specialix supported Driver!** # The host card is memory, not IO mapped. # The Rev 1 host cards use a 64K chunk, on a 32K boundary. # The Rev 2 host cards use a 32K chunk, on a 32K boundary. # The cards can use an IRQ of 11, 12 or 15. device coremctl device dimm device ecc device joy0 at isa? port IO_GAME # nullmodem terminal driver device nmdm device tpm options TPM_HARVEST # This options turns TPM into entropy source. device ipmi # The adw driver will attempt to use memory mapped I/O for all PCI # controllers that have it configured only if this option is set. options ADW_ALLOW_MEMIO # # PCI devices & PCI options: # # The main PCI bus device is `pci'. It provides auto-detection and # configuration support for all devices on the PCI bus, using either # configuration mode defined in the PCI specification. device pci # AGP GART support # device agp # # AGP debugging. # options AGP_DEBUG # The `amd' device provides support for the AMD 53C974 SCSI host # adapter chip as found on devices such as the Tekram DC-390(T). # # The `bge' device provides support for gigabit ethernet adapters # based on the Broadcom BCM570x family of controllers, including the # 3Com 3c996-T, the Netgear GA302T, the SysKonnect SK-9D21 and SK-9D41, # and the embedded gigE NICs on Dell PowerEdge 2550 servers. # # The `ncr' device provides support for the NCR 53C810 and 53C825 # self-contained SCSI host adapters. # # The `isp' device provides support for the Qlogic ISP 1020, 1040 # nd 1040B PCI SCSI host adapters, ISP 1240 Dual Ultra SCSI, # ISP 1080 and 1280 (Dual) Ultra2, ISP 12160 Ultra3 SCSI, as well as # the Qlogic ISP 2100 and ISP 2200 Fibre Channel Host Adapters. # # The `dc' device provides support for PCI fast ethernet adapters # based on the DEC/Intel 21143 and various workalikes including: # the ADMtek AL981 Comet and AN985 Centaur, the ASIX Electronics # AX88140A and AX88141, the Davicom DM9100 and DM9102, the Lite-On # 82c168 and 82c169 PNIC, the Lite-On/Macronix LC82C115 PNIC II # and the Macronix 98713/98713A/98715/98715A/98725 PMAC. This driver # replaces the old al, ax, dm, pn and mx drivers. List of brands: # Digital DE500-BA, Kingston KNE100TX, D-Link DFE-570TX, SOHOware SFA110, # SVEC PN102-TX, CNet Pro110B, 120A, and 120B, Compex RL100-TX, # LinkSys LNE100TX, LNE100TX V2.0, Jaton XpressNet, Alfa Inc GFC2204, # KNE110TX. # # The `de' device provides support for the Digital Equipment DC21040 # self-contained Ethernet adapter. # # The `em' device provides support for the Intel Pro/1000 Family of Gigabit # adapters (82542, 82543, 82544, 82540). # # The `et' device provides support for the Agere ET1310 10/100/1000 PCIe # adapters. # # The `fxp' device provides support for the Intel EtherExpress Pro/100B # PCI Fast Ethernet adapters. # # The 'lge' device provides support for PCI gigabit ethernet adapters # based on the Level 1 LXT1001 NetCellerator chipset. This includes the # D-Link DGE-500SX, SMC TigerCard 1000 (SMC9462SX), and some Addtron cards. # # The 'my' device provides support for the Myson MTD80X and MTD89X PCI # Fast Ethernet adapters. # # The 'nge' device provides support for PCI gigabit ethernet adapters # based on the National Semiconductor DP83820 and DP83821 chipset. This # includes the SMC EZ Card 1000 (SMC9462TX), D-Link DGE-500T, Asante # FriendlyNet GigaNIX 1000TA and 1000TPC, the Addtron AEG320T, the # LinkSys EG1032 and EG1064, the Surecom EP-320G-TX and the Netgear GA622T. # # The 'oce' device provides support for Emulex 10 Gbit adapters # (OneConnect Ethernet). # # The 'pcn' device provides support for PCI fast ethernet adapters based # on the AMD Am79c97x chipsets, including the PCnet/FAST, PCnet/FAST+, # PCnet/PRO and PCnet/Home. These were previously handled by the lnc # driver (and still will be if you leave this driver out of the kernel). # # Te 're' device provides support for PCI GigaBit ethernet adapters based # on the RealTek 8169 chipset. It also supports the 8139C+ and is the # preferred driver for that chip. # # The 'rl' device provides support for PCI fast ethernet adapters based # on the RealTek 8129/8139 chipset. Note that the RealTek driver defaults # to using programmed I/O to do register accesses because memory mapped # mode seems to cause severe lockups on SMP hardware. This driver also # supports the Accton EN1207D `Cheetah' adapter, which uses a chip called # the MPX 5030/5038, which is either a RealTek in disguise or a RealTek # workalike. Note that the D-Link DFE-530TX+ uses the RealTek chipset # and is supported by this driver, not the 'vr' driver. # # The 'sf' device provides support for Adaptec Duralink PCI fast # ethernet adapters based on the Adaptec AIC-6915 "starfire" controller. # This includes dual and quad port cards, as well as one 100baseFX card. # Most of these are 64-bit PCI devices, except for one single port # card which is 32-bit. # # The 'ste' device provides support for adapters based on the Sundance # Technologies ST201 PCI fast ethernet controller. This includes the # D-Link DFE-550TX. # # The 'sis' device provides support for adapters based on the Silicon # Integrated Systems SiS 900 and SiS 7016 PCI fast ethernet controller # chips. # # The 'sk' device provides support for the SysKonnect SK-984x series # PCI gigabit ethernet NICs. This includes the SK-9841 and SK-9842 # single port cards (single mode and multimode fiber) and the # SK-9843 and SK-9844 dual port cards (also single mode and multimode). # The driver will autodetect the number of ports on the card and # attach each one as a separate network interface. # # The 'ti' device provides support for PCI gigabit ethernet NICs based # on the Alteon Networks Tigon 1 and Tigon 2 chipsets. This includes the # Alteon AceNIC, the 3Com 3c985, the Netgear GA620 and various others. # Note that you will probably want to bump up NMBCLUSTERS a lot to use # this driver. # # The 'tl' device provides support for the Texas Instruments TNETE100 # series 'ThunderLAN' cards and integrated ethernet controllers. This # includes several Compaq Netelligent 10/100 cards and the built-in # ethernet controllers in several Compaq Prosignia, Proliant and # Deskpro systems. It also supports several Olicom 10Mbps and 10/100 # boards. # # The `tx' device provides support for the SMC 9432 TX, BTX and FTX cards. # # The `txp' device provides support for the 3Com 3cR990 "Typhoon" # 10/100 adapters. # # The `vr' device provides support for various fast ethernet adapters # based on the VIA Technologies VT3043 `Rhine I' and VT86C100A `Rhine II' # chips, including the D-Link DFE530TX (see 'rl' for DFE530TX+), the Hawking # Technologies PN102TX, and the AOpen/Acer ALN-320. # # The `wb' device provides support for various fast ethernet adapters # based on the Winbond W89C840F chip. Note: this is not the same as # the Winbond W89C940F, which is an NE2000 clone. # # The `xl' device provides support for the 3Com 3c900, 3c905 and # 3c905B (Fast) Etherlink XL cards and integrated controllers. This # includes the integrated 3c905B-TX chips in certain Dell Optiplex and # Dell Precision desktop machines and the integrated 3c905-TX chips # in Dell Latitude laptop docking stations. # # The 'bktr' device is a PCI video capture device using the Brooktree # bt848/bt848a/bt849a/bt878/bt879 chipset. When used with a TV Tuner it forms a # TV card, eg Miro PC/TV, Hauppauge WinCast/TV WinTV, VideoLogic Captivator, # Intel Smart Video III, AverMedia, IMS Turbo, FlyVideo. # # options OVERRIDE_CARD=xxx # options OVERRIDE_TUNER=xxx # options OVERRIDE_MSP=1 # options OVERRIDE_DBX=1 # These options can be used to override the auto detection # The current values for xxx are found in src/sys/dev/video/bktr/bktr_card.h # Using sysctl(8) run-time overrides on a per-card basis can be made # # options BKTR_SYSTEM_DEFAULT=BROOKTREE_PAL # or # options BKTR_SYSTEM_DEFAULT=BROOKTREE_NTSC # Specifies the default video capture mode. # This is required for Dual Crystal (28&35Mhz) boards where PAL is used # to prevent hangs during initialisation. eg VideoLogic Captivator PCI. # # options BKTR_USE_PLL # PAL or SECAM users who have a 28Mhz crystal (and no 35Mhz crystal) # must enable PLL mode with this option. eg some new Bt878 cards. # # options BKTR_GPIO_ACCESS # This enable IOCTLs which give user level access to the GPIO port. # # options BKTR_NO_MSP_RESET # Prevents the MSP34xx reset. Good if you initialise the MSP in another OS first # # options BKTR_430_FX_MODE # Switch Bt878/879 cards into Intel 430FX chipset compatibility mode. # # options BKTR_SIS_VIA_MODE # Switch Bt878/879 cards into SIS/VIA chipset compatibility mode which is # needed for some old SiS and VIA chipset motherboards. # This also allows Bt878/879 chips to work on old OPTi (<1997) chipset # motherboards and motherboards with bad or incomplete PCI 2.1 support. # As a rough guess, old = before 1998 # # options BKTR_NEW_MSP34XX_DRIVER # Use new, more complete initialization scheme for the msp34* soundchip. # Should fix stereo autodetection if the old driver does only output # mono sound. # # options BKTR_OVERRIDE_CARD=xxx # options BKTR_OVERRIDE_DBX=xxx # options BKTR_OVERRIDE_MSP=xxx # options BKTR_OVERRIDE_TUNER=xxx # These options can be used to select a specific device, regardless of # the autodetection and i2c device checks (see comments in bktr_card.c). # device amd # AMD 53C974 (Tekram DC-390(T)) device isp # Qlogic family device ispfw # Firmware for QLogic HBAs device mpr # LSI-Logic MPT-Fusion 3 device mps # LSI-Logic MPT-Fusion 2 device mpt # LSI '909 FC adapters device ncr # NCR/Symbios Logic device sym # NCR/Symbios Logic (newer chipsets) device trm # Tekram DC395U/UW/F and DC315U # # Options for ISP # # ISP_TARGET_MODE - enable target mode operation #options ISP_TARGET_MODE=1 # Options used in dev/disk/sym/ (Symbios SCSI driver). #options SYM_SETUP_LP_PROBE_MAP #-Low Priority Probe Map (bits) # Allows the ncr to take precedence # 1 (1<<0) -> 810a, 860 # 2 (1<<1) -> 825a, 875, 885, 895 # 4 (1<<2) -> 895a, 896, 1510d #options SYM_SETUP_SCSI_DIFF #-HVD support for 825a, 875, 885 # disabled:0 (default), enabled:1 #options SYM_SETUP_PCI_PARITY #-PCI parity checking # disabled:0, enabled:1 (default) #options SYM_SETUP_MAX_LUN #-Number of LUNs supported # default:8, range:[1..64] # MII bus support is required for some PCI 10/100 ethernet NICs, # namely those which use MII-compliant transceivers or implement # transceiver control interfaces that operate like an MII. Adding # "device miibus0" to the kernel config pulls in support for # the generic miibus API and all of the PHY drivers, including a # generic one for PHYs that aren't specifically handled by an # individual driver. device miibus # PCI Ethernet NICs that use the common MII bus controller code. device ae # Attansic/Atheros L2 Fast Ethernet device alc # Atheros AR8131/AR8132 device ale # Atheros AR8121/AR8113/AR8114 device age # Attansic/Atheros L1 Gigabit Ethernet device bce # Broadcom NetXtreme II Gigabit Ethernet device bfe # Broadcom BCM440x 10/100 Ethernet device bnx # Broadcom NetXtreme 5718/57785 Gigabit Ethernet device dc # DEC/Intel 21143 and various workalikes device fxp # Intel EtherExpress PRO/100B (82557, 82558) device my # Myson Fast Ethernet (MTD80X, MTD89X) device pcn # AMD Am79C97x PCI 10/100 NICs device re # RealTek 8139C+/8169 device rl # RealTek 8129/8139 device sbsh # Granch SBNI16 SHDSL modem device sf # Adaptec AIC-6915 (``Starfire'') device sis # Silicon Integrated Systems SiS 900/SiS 7016 device ste # Sundance ST201 (D-Link DFE-550TX) device tl # Texas Instruments ThunderLAN device tx # SMC EtherPower II (83c17x ``EPIC'') device vge # VIA 612x GigE device vr # VIA Rhine, Rhine II device wb # Winbond W89C840F device xl # 3Com 3c90x (``Boomerang'', ``Cyclone'') # PCI Ethernet NICs. device de # DEC/Intel DC21x4x (``Tulip'') device txp # 3Com 3cR990 (``Typhoon'') # Gigabit Ethernet NICs. device bge # Broadcom BCM570x (``Tigon III'') device em # Intel Pro/1000 (8254x,8257x) # Requires ig_hal device emx # Intel Pro/1000 (8257{1,2,3,4}) # Requires ig_hal device igb # Intel Pro/1000 (82575, 82576, 82580, i350) # Requires ig_hal device ig_hal # Intel Pro/1000 hardware abstraction layer device ix # Intel PRO/10GbE PCIE Ethernet Family device et # Agere ET1310 10/100/1000 Ethernet device lge # Level 1 LXT1001 (``Mercury'') device mxge # Myricom Myri-10G 10GbE NIC device mxgefw # Firmware for Myricom Myri-10G 10GbE NIC device nfe # nVidia nForce2/3 MCP04/51/55 CK804 device nge # NatSemi DP83820 and DP83821 device oce # Emulex 10 GbE (OneConnect Ethernet) device sk # SysKonnect GEnesis, LinkSys EG1023, D-Link device ti # Alteon (``Tigon I'', ``Tigon II'') device stge # Sundance/Tamarack TC9021 Gigabit Ethernet device msk # Marvell/SysKonnect Yukon II Gigabit Ethernet device jme # JMicron Gigabit/Fast Ethernet # Brooktree driver has been ported to the new I2C framework. Thus, # you'll need to have the following 3 lines in the kernel config. # device smbus # device iicbus # device iicbb # The iic and smb devices are only needed if you want to control other # I2C slaves connected to the external connector of some cards. # device bktr options BKTR_NEW_MSP34XX_DRIVER # WinTV PVR-250/350 driver device cxm # # PCCARD/PCMCIA # # pccard: pccard slots # cardbus/cbb: cardbus bridge device pccard device cardbus device cbb # # MMC/SD # # mmc MMC/SD bus # mmcsd MMC/SD memory card # sdhci Generic PCI SD Host Controller # device mmc device mmcsd device sdhci # # SMB bus # # System Management Bus support is provided by the 'smbus' device. # Access to the SMBus device is via the 'smb' device (/dev/smb*), # which is a child of the 'smbus' device. # # Supported devices: # smb standard io through /dev/smb* # # ACPI support: # smbacpi support for ACPI I2cSerialBus resources # # Supported SMB interfaces: # iicsmb I2C to SMB bridge with any iicbus interface # bktr brooktree848 I2C hardware interface # intpm Intel PIIX4 (82371AB, 82443MX) Power Management Unit # alpm Acer Aladdin-IV/V/Pro2 Power Management Unit # ichiic Intel generation 4 I2C controller # ichsmb Intel ICH SMBus controller chips (82801AA, 82801AB, 82801BA) # viapm VIA VT82C586B,596,686A and VT8233 SMBus controllers # amdpm AMD 756 Power Management Unit # amdsmb AMD 8111 SMBus 2.0 Controller # device smbus # Bus support, required for smb below. device intpm device alpm device ichiic device ichsmb device viapm device amdpm device amdsmb device smb device smbacpi # # I2C Bus # # Philips i2c bus support is provided by the `iicbus' device. # # Supported devices: # ic i2c network interface # iic i2c standard io # iicsmb i2c to smb bridge. Allow i2c i/o with smb commands. # # Supported interfaces: # pcf Philips PCF8584 ISA-bus controller # bktr brooktree848 I2C software interface # # Other: # iicbb generic I2C bit-banging code (needed by lpbb, bktr) # device iicbus # Bus support, required for ic/iic/iicsmb below. device iicbb device ic device iic device iicsmb # smb over i2c bridge device pcf0 at isa? port 0x320 irq 5 # Intel performance-energy bias device perfbias # Intel software controlled clock modulation device clockmod # Intel Sandy Bridge and newer CPUs power usage estimation device corepower # amdtemp: On-die sensor on AMD K8/K10/K11 CPUs # coretemp: Intel Core and newer CPUs on-die digital thermal sensor support device amdtemp device coretemp # Generic panel backlight support device backlight # Memory thermal sensor device memtemp # CPU control pseudo-device. Provides access to MSRs, CPUID info and # microcode update feature. device cpuctl # # AMD System Management Network (SMN) # device amdsmn # Effective CPU frequency interface via APERF/MPERF MSRs device aperf # AMD Family 0Fh, 10h and 11h temperature sensors device kate device km # ThinkPad Active Protection System accelerometer device aps0 at isa? port 0x1600 # HW monitoring devices lm(4), it(4) and nsclpcsio. device lm0 at isa? port 0x290 device it0 at isa? port 0x290 device it1 at isa? port 0xc00 device it2 at isa? port 0xd00 device it3 at isa? port 0x228 device nsclpcsio0 at isa? port 0x2e device nsclpcsio1 at isa? port 0x4e device wbsio0 at isa? port 0x2e device wbsio1 at isa? port 0x4e device uguru0 at isa? port 0xe0 # ABIT uGuru # EFI Runtime Services support (not functional yet). options EFIRT # Parallel-Port Bus # # Parallel port bus support is provided by the `ppbus' device. # Multiple devices may be attached to the parallel port, devices # are automatically probed and attached when found. # # Supported devices: # vpo Iomega Zip Drive # Requires SCSI disk support ('scbus' and 'da'); the best # performance is achieved with ports in EPP 1.9 mode. # lpt Parallel Printer # plip Parallel network interface # ppi General-purpose I/O ("Geek Port") + IEEE1284 I/O # pps Pulse per second Timing Interface # lpbb Philips official parallel port I2C bit-banging interface # # Supported interfaces: # ppc ISA-bus parallel port interfaces. # options PPC_PROBE_CHIPSET # Enable chipset specific detection # (see flags in ppc(4)) options DEBUG_1284 # IEEE1284 signaling protocol debug options PERIPH_1284 # Makes your computer act as an IEEE1284 # compliant peripheral options DONTPROBE_1284 # Avoid boot detection of PnP parallel devices options VP0_DEBUG # ZIP/ZIP+ debug options LPT_DEBUG # Printer driver debug options PPC_DEBUG=2 # Parallel chipset level debug options PLIP_DEBUG # Parallel network IP interface debug options PCFCLOCK_VERBOSE # Verbose pcfclock driver options PCFCLOCK_MAX_RETRIES=5 # Maximum read tries (default 10) device ppc0 at isa? irq 7 device ppbus device vpo device lpt device plip device ppi device pps device lpbb device pcfclock # Kernel BOOTP support options BOOTP # Use BOOTP to obtain IP address/hostname options BOOTP_NFSROOT # NFS mount root filesystem using BOOTP info options BOOTP_COMPAT # Workaround for broken bootp daemons. options BOOTP_WIRED_TO=fxp0 # Use interface fxp0 for BOOTP # Disable swapping. This option removes all code which actually performs # swapping, so it's not possible to turn it back on at run-time. # # This is sometimes usable for systems which don't have any swap space # (see also sysctls "vm.defer_swapspace_pageouts" and # "vm.disable_swapspace_pageouts") # #options NO_SWAPPING # Set the size of the buffer cache KVM reservation, in buffers. This is # scaled by approximately 16384 bytes. The system will auto-size the buffer # cache if this option is not specified. # options NBUF=512 # Set the size of the mbuf KVM reservation, in clusters. This is scaled # by approximately 2048 bytes. The system will auto-size the mbuf area # to (512 + maxusers*16) if this option is not specified. # maxusers is in turn computed at boot time depending on available memory # or set to the value specified by "options MAXUSERS=x" (x=0 means # autoscaling). # So, to take advantage of autoscaling, you have to remove both # NMBCLUSTERS and MAXUSERS (and NMBUFS) from your kernel config. # options NMBCLUSTERS=1024 # Set the number of mbufs available in the system. Each mbuf # consumes 256 bytes. The system will autosize this (to 4 times # the number of NMBCLUSTERS, depending on other constraints) # if this option is not specified. # options NMBUFS=4096 # Tune the buffer cache maximum KVA reservation, in bytes. The maximum is # usually capped at 200 MB, effecting machines with > 1GB of ram. Note # that the buffer cache only really governs write buffering and disk block # translations. The VM page cache is our primary disk cache and is not # effected by the size of the buffer cache. # options VM_BCACHE_SIZE_MAX="(100*1024*1024)" # Tune the swap zone KVA reservation, in bytes. The default is typically # 70 MB, giving the system the ability to manage a maximum of 28GB worth # of swapped out data. # options VM_SWZONE_SIZE_MAX="(50*1024*1024)" # # Enable extra debugging code for locks. This stores the filename and # line of whatever acquired the lock in the lock itself, and change a # number of function calls to pass around the relevant data. This is # not at all useful unless you are debugging lock code. Also note # that it is likely to break e.g. fstat(1) unless you recompile your # userland with -DDEBUG_LOCKS as well. # # DEBUG_LOCKS_LATENCY adds a sysctl to add a forced latency loop # (count to N) in front of any spinlock or gettoken. # options DEBUG_LOCKS options DEBUG_LOCKS_LATENCY # Set the amount of time (in seconds) the system will wait before # rebooting automatically when a kernel panic occurs. If set to (-1), # the system will wait indefinitely until a key is pressed on the # console. options PANIC_REBOOT_WAIT_TIME=16 # Specify a lower limit for the number of swap I/O buffers. # options NSWBUF_MIN=120 # The 'asr' driver provides support for current DPT/Adaptec SCSI RAID # controllers (SmartRAID V and VI and later). # These controllers require the CAM infrastructure. # device asr # The 'dpt' driver provides support for DPT controllers (http://www.dpt.com/). # These have hardware RAID-{0,1,5} support, and do multi-initiator I/O. # The DPT controllers are commonly re-licensed under other brand-names - # some controllers by Olivetti, Dec, HP, AT&T, SNI, AST, Alphatronic, NEC and # Compaq are actually DPT controllers. # # See src/sys/dev/raid/dpt for debugging and other subtle options. # DPT_MEASURE_PERFORMANCE Enables a set of (semi)invasive metrics. Various # instruments are enabled. The tools in # /usr/sbin/dpt_* assume these to be enabled. # DPT_HANDLE_TIMEOUTS Normally device timeouts are handled by the DPT. # If you ant the driver to handle timeouts, enable # this option. If your system is very busy, this # option will create more trouble than solve. # DPT_TIMEOUT_FACTOR Used to compute the excessive amount of time to # wait when timing out with the above option. # DPT_DEBUG_xxxx These are controllable from sys/dev/raid/dpt/dpt.h # DPT_LOST_IRQ When enabled, will try, once per second, to catch # any interrupt that got lost. Seems to help in some # DPT-firmware/Motherboard combinations. Minimal # cost, great benefit. # DPT_RESET_HBA Make "reset" actually reset the controller # instead of fudging it. Only enable this if you # are 100% certain you need it. device dpt # DPT options #!CAM# options DPT_MEASURE_PERFORMANCE #!CAM# options DPT_HANDLE_TIMEOUTS options DPT_TIMEOUT_FACTOR=4 options DPT_LOST_IRQ options DPT_RESET_HBA # # Compaq "CISS" RAID controllers (SmartRAID 5* series) # These controllers have a SCSI-like interface, and require the # CAM infrastructure. # device ciss # # Intel Integrated RAID controllers. # This driver is supported and maintained by # "Leubner, Achim" . # device iir # # Mylex AcceleRAID and eXtremeRAID controllers with v6 and later # firmware. These controllers have a SCSI-like interface, and require # the CAM infrastructure. # device mly # USB support # # UHCI controller device uhci # OHCI controller device ohci # EHCI controller device ehci # XHCI controller device xhci # General USB code (mandatory for USB) device usb # Human Interface Device (anything with buttons and dials) device uhid # USB keyboard device ukbd # USB printer device ulpt # USB mass storage (Requires scbus and da) device umass # USB mass storage driver for device-side mode device usfs # USB modem support device umodem # USB mouse device ums # USB touchpad(s) device wsp # eGalax USB touch screen device uep # Diamond Rio 500 MP3 player device urio # USB com devices device "u3g" device uark device ubsa device ubser device uchcom device ucom device ucycom device ufoma device uftdi device ugensa device uipaq device umcs device umct device umoscom device uplcom device uslcom device uvisor device uvscom # # USB ethernet support device uether # # ADMtek USB ethernet. Supports the LinkSys USB100TX, # the Billionton USB100, the Melco LU-ATX, the D-Link DSB-650TX # and the SMC 2202USB. Also works with the ADMtek AN986 Pegasus # eval board. device aue # # ASIX Electronics AX88172 USB 2.0 ethernet driver. Used in the # LinkSys USB200M and various other adapters. device axe # # ASIX Electronics AX88178A/AX88179 USB 2.0/3.0 gigabit ethernet driver. device axge # # Devices which communicate using Ethernet over USB, particularly # Communication Device Class (CDC) Ethernet specification. Supports # Sharp Zaurus PDAs, some DOCSIS cable modems and so on. device cdce # # CATC USB-EL1201A USB ethernet. Supports the CATC Netmate # and Netmate II, and the Belkin F5U111. device cue # # USB Apple iPhone/iPad tethered Ethernet driver device ipheth # # Kawasaki LSI ethernet. Supports the LinkSys USB10T, # Entrega USB-NET-E45, Peracom Ethernet Adapter, the # 3Com 3c19250, the ADS Technologies USB-10BT, the ATen UC10T, # the Netgear EA101, the D-Link DSB-650, the SMC 2102USB # and 2104USB, and the Corega USB-T. device kue # # Moschip MCS7730/MCS7840 USB to fast ethernet. Supports the Sitecom LN030. device mos # # Davicom DM9601E USB to fast ethernet. Supports the Corega FEther USB-TXC. device udav # USB wireless NICs, requires wlan_amrr # # Ralink Technology RT2501USB/RT2601USB device rum # # Ralink Technology RT2700U/RT2800U/RT3000U wireless driver device run device runfw # # RNDIS USB ethernet driver device urndis # # Realtek RTL8188CU/RTL8192CU wireless driver device urtwn device urtwnfw #options URTWN_WITHOUT_UCODE # Fm Radio # device ufm # Templates for programming USB device side drivers # device usb_template # debugging options for the USB subsystem # options USB_DEBUG # options for ukbd: options UKBD_DFLT_KEYMAP # specify the built-in keymap makeoptions UKBD_DFLT_KEYMAP=it.iso # Firewire support device firewire # Firewire bus code device sbp # SCSI over Firewire (Requires scbus and da) device fwe # Ethernet over Firewire (non-standard!) # dcons support (Dumb Console Device) device dcons # dumb console driver device dcons_crom # FireWire attachment options DCONS_BUF_SIZE=16384 # buffer size options DCONS_POLL_HZ=100 # polling rate options DCONS_FORCE_CONSOLE=1 # force to be the primary console options DCONS_FORCE_GDB=1 # force to be the gdb device ##################################################################### # crypto subsystem # # This is a port of the openbsd crypto framework. Include this when # you have a h/w crypto device to accelerate user applications that # link to openssl. # # Drivers are ports from openbsd with some simple enhancements that have # been fed back to openbsd (and hopefully will be included). device crypto # core crypto support device cryptodev # /dev/crypto for access to h/w device rndtest # FIPS 140-2 entropy tester device hifn # Hifn 7951, 7781, etc. options HIFN_DEBUG # enable debugging support: hw.hifn.debug #options HIFN_NO_RNG # for devices without RNG options HIFN_RNDTEST # enable rndtest support device safe # SafeNet 1141 options SAFE_DEBUG # enable debugging support: hw.safe.debug #options SAFE_NO_RNG # for devices without RNG options SAFE_RNDTEST # enable rndtest support device ubsec # Broadcom 5501, 5601, 58xx options UBSEC_DEBUG # enable debugging support: hw.ubsec.debug #options UBSEC_NO_RNG # for devices without RNG options UBSEC_RNDTEST # enable rndtest support device aesni # hardware crypto/RNG for AES-NI device padlock # hardware crypto/RNG for VIA C3/C7/Eden device rdrand # hardware RNG for RdRand # # ACPI support using the Intel ACPI Component Architecture reference # implementation. # # ACPI_DEBUG enables the use of the debug.acpi.level and debug.acpi.layer # kernel environment variables to select initial debugging levels for the # Intel ACPICA code. device acpi options ACPI_DEBUG # ACPI WMI Mapping driver device acpi_wmi # ACPI Asus Extras (LCD backlight/brightness, video output, etc.) device acpi_asus # ACPI Fujitsu Extras (Buttons) device acpi_fujitsu # ACPI extras driver for HP laptops device acpi_hp # ACPI Panasonic Extras (LCD backlight/brightness, video output, etc.) device acpi_panasonic # ACPI pvpanic driver for virtual machines running in Qemu device acpi_pvpanic # ACPI Sony extra (LCD brightness) device acpi_sony # ACPI extras driver for ThinkPad laptops device acpi_thinkpad # ACPI Toshiba Extras (LCD backlight/brightness, video output, etc.) device acpi_toshiba # ACPI Video Extensions (LCD backlight/brightness, video output, etc.) device acpi_video # ACPI Docking Station device acpi_dock device aibs # ASUSTeK AI Booster (ACPI ASOC ATK0110) # DRM options: # drm: General DRM code # i915: Intel integrated GPUs, starting from the 830M family # radeon: ATI/AMD Radeon cards # # DRM_DEBUG: include debug printfs, very slow # # DRM requires AGP in the kernel. # # Also you'll need to have the following 3 lines in the kernel config. # device acpi # device iicbus # device iicbb device drm # For testing and debugging. device "i915" device radeon options DRM_DEBUG options VGA_SWITCHEROO # # Misc devices # device cmx # Omnikey CardMan 4040 smartcard reader device amdsbwd # AMD South Bridge watchdog device gpio # Enable support for the gpio framework device ichwd # Intel ICH watchdog interrupt timer device tbridge # regression testing # # Amazon EC2 support # device ena # # Hyper-V support # device vmbus # # Virtio support # device virtio # Generic VirtIO bus/PCI interface (required) device virtio_balloon # VirtIO Memory Balloon device device virtio_blk # VirtIO Block device device virtio_random # VirtIO Entropy device device virtio_scsi # VirtIO SCSI device device vtnet # VirtIO Ethernet device # VMware support # device pvscsi # VMware PVSCSI options PVSCSI_DEBUG_LOGGING device vmx # VMware VMXNET3 Ethernet # # Gpio support for ACPI based SoC platforms # device gpio_acpi device gpio_intel # GPIO support for Intel SoCs # # Embedded system options: # # An embedded system might want to run something other than init. options INIT_PATH="/sbin/init:/sbin/oinit" # Debug options options BUS_DEBUG # enable newbus debugging options RSS_DEBUG # enable RSS (Receive Side Scaling) debugging # Record the program counter of the code interrupted by the statistics # clock interrupt. Use pctrack(8) to dump this information. options DEBUG_PCTRACK # evdev interface device evdev # input event device support options EVDEV_SUPPORT # evdev support in legacy drivers options EVDEV_DEBUG # enable event debug messages # More undocumented options for linting. # Note that documenting these are not considered an affront. #options BKTR_ALLOC_PAGES=xxx options CAM_DEBUG_DELAY options CLUSTERDEBUG options DEBUG options DEBUG_CRIT_SECTIONS options BCE_RSS_DEBUG options BCE_TSS_DEBUG options BNX_RSS_DEBUG options BNX_TSO_DEBUG options BNX_TSS_DEBUG options EMX_RSS_DEBUG options EMX_TSO_DEBUG options EMX_TSS_DEBUG options JME_RSS_DEBUG options IGB_RSS_DEBUG options IGB_TSS_DEBUG options IGB_MSIX_DEBUG options IX_RSS_DEBUG options ENABLE_ALART options FB_DEBUG=2 options FB_INSTALL_CDEV #options IEEE80211_DEBUG_REFCNT options IEEE80211_SUPPORT_SUPERG options KBDIO_DEBUG=10 options KBD_MAXRETRY=4 options KBD_MAXWAIT=6 options KBD_RESETDELAY=201 #options KERN_TIMESTAMP options KEY options LOCKF_DEBUG #options MAXFILES=xxx options MBUF_DEBUG options NO_LWKT_SPLIT_USERPRI options PANIC_DEBUG options PMAP_DEBUG options PSM_DEBUG=4 options SCSI_NCR_DEBUG options SCSI_NCR_MAX_SYNC=10000 options SCSI_NCR_MAX_WIDE=1 options SCSI_NCR_MYADDR=7 options SLAB_DEBUG options SOCKBUF_DEBUG options TDMA_BINTVAL_DEFAULT=5 options TDMA_SLOTCNT_DEFAULT=2 options TDMA_SLOTLEN_DEFAULT=10*1000 options TDMA_TXRATE_11A_DEFAULT=2*24 options TDMA_TXRATE_11B_DEFAULT=2*11 options TDMA_TXRATE_11G_DEFAULT=2*24 options TDMA_TXRATE_11NA_DEFAULT="(4|IEEE80211_RATE_MCS)" options TDMA_TXRATE_11NG_DEFAULT="(4|IEEE80211_RATE_MCS)" options TDMA_TXRATE_HALF_DEFAULT=2*12 options TDMA_TXRATE_QUARTER_DEFAULT=2*6 options TDMA_TXRATE_TURBO_DEFAULT=2*24 #options TIMER_FREQ="((14318182+6)/12)" options VFS_BIO_DEBUG options VM_PAGE_DEBUG options XBONEHACK options KTR options KTR_ALL options KTR_ENTRIES=1024 options KTR_VERBOSE=1 #options KTR_ACPI_EC #options KTR_CTXSW #options KTR_DMCRYPT #options KTR_ETHERNET #options KTR_HAMMER #options KTR_IFQ #options KTR_IF_BGE #options KTR_IF_EM #options KTR_IF_EMX #options KTR_IF_POLL #options KTR_IF_START #options KTR_IPIQ #options KTR_KERNENTRY #options KTR_LAPIC #options KTR_MEMORY #options KTR_SERIALIZER #options KTR_SOWAKEUP #options KTR_SPIN_CONTENTION #options KTR_TESTLOG #options KTR_TOKENS #options KTR_TSLEEP #options KTR_UDP #options KTR_USCHED_BSD4 #options KTR_USCHED_DFLY # ALTQ options ALTQ #alternate queueing options ALTQ_CBQ #class based queueing options ALTQ_RED #random early detection options ALTQ_RIO #triple red for diffserv (needs RED) options ALTQ_HFSC #hierarchical fair service curve options ALTQ_PRIQ #priority queue options ALTQ_FAIRQ #fair queue #options ALTQ_NOPCC #don't use processor cycle counter options ALTQ_DEBUG #for debugging # you might want to set kernel timer to 1kHz if you use CBQ, # especially with 100baseT #options HZ_DEFAULT=1000 # WATCHDOG options WDOG_DISABLE_ON_PANIC # Automatically disable watchdogs on panic # LED device led options ERROR_LED_ON_PANIC # If an error led is present, light it up on panic