Yet another round of typo fixes in manpages and messages.

diff --git a/sbin/ifconfig/ifconfig.8 b/sbin/ifconfig/ifconfig.8
index 5d2c733..6096e4a 100644 (file)
--- a/sbin/ifconfig/ifconfig.8
+++ b/sbin/ifconfig/ifconfig.8
@@ -1074,9 +1074,9 @@ In particular the information elements included in management frames
 for old devices are different.
 When compatibility support is enabled both standard and compatible data
 will be provided.
-Stations that associate using the compatiblity mechanisms are flagged
+Stations that associate using the compatibility mechanisms are flagged
 in ``list sta''.
-To disable compatiblity support use
+To disable compatibility support use
 .Fl htcompat .
 .It Cm htprotmode Ar technique
 For interfaces operating in 802.11n, use the specified

diff --git a/sbin/ifconfig/ifieee80211.c b/sbin/ifconfig/ifieee80211.c
index 0027b59..044253a 100644 (file)
--- a/sbin/ifconfig/ifieee80211.c
+++ b/sbin/ifconfig/ifieee80211.c
@@ -5027,7 +5027,7 @@ DECL_CMD_FUNC(set80211clone_wlanaddr, arg, d)
 
        ea = ether_aton(arg);
        if (ea == NULL)
-               errx(1, "%s: cannot parse addres", arg);
+               errx(1, "%s: cannot parse address", arg);
        memcpy(params.icp_macaddr, ea->octet, IEEE80211_ADDR_LEN);
        params.icp_flags |= IEEE80211_CLONE_MACADDR;
 }

diff --git a/share/man/man4/aac.4 b/share/man/man4/aac.4
index cf47e88..21f1e0e 100644 (file)
--- a/share/man/man4/aac.4
+++ b/share/man/man4/aac.4
@@ -60,7 +60,7 @@ Access to RAID containers is available via the
 device nodes.
 The
 .Nm aacp
-device enables the SCSI pass-thru interface and allows devices connected
+device enables the SCSI pass-through interface and allows devices connected
 to the card such as CD-ROMs to be available via the CAM
 .Xr scsi 4
 subsystem.

diff --git a/sys/netproto/802_11/wlan/ieee80211_node.c b/sys/netproto/802_11/wlan/ieee80211_node.c
index 4e5f6c4..93398bb 100644 (file)
--- a/sys/netproto/802_11/wlan/ieee80211_node.c
+++ b/sys/netproto/802_11/wlan/ieee80211_node.c
@@ -433,7 +433,7 @@ ieee80211_reset_bss(struct ieee80211vap *vap)
        ieee80211_reset_erp(ic);
 
        ni = ieee80211_alloc_node(&ic->ic_sta, vap, vap->iv_myaddr);
-       KASSERT(ni != NULL, ("unable to setup inital BSS node"));
+       KASSERT(ni != NULL, ("unable to setup initial BSS node"));
        obss = vap->iv_bss;
        vap->iv_bss = ieee80211_ref_node(ni);
        if (obss != NULL) {

diff --git a/usr.sbin/mptutil/mptutil.8 b/usr.sbin/mptutil/mptutil.8
index 40cfa9c..56b2407 100644 (file)
--- a/usr.sbin/mptutil/mptutil.8
+++ b/usr.sbin/mptutil/mptutil.8
@@ -123,7 +123,7 @@ where
 is the bus ID and
 .Ar yy
 is the target ID.
-If the bus ID is ommitted,
+If the bus ID is omitted,
 the volume is assumed to be on bus 0.
 Second,
 on the volume may be specified by the corresponding