From: Sepherosa Ziehau Date: Sun, 15 Feb 2009 11:46:46 +0000 (+0800) Subject: em(4): Sync with Intel's em-6.9.6(FreeBSD) X-Git-Tag: v2.3.1~352^2~16 X-Git-Url: https://gitweb.dragonflybsd.org/dragonfly.git/commitdiff_plain/9c80d176fa568ed18fc8c8678f763f9a04556d08 em(4): Sync with Intel's em-6.9.6(FreeBSD) In addition to adding support for some chips (e.g. 82574L), this also gives me the chance to rearrange and clean up if_em.[ch] :) Noticable changes to the FreeBSD driver: - The hardware abstraction layer is put into a seperate module (ig_hal) - IP csum offloading is supported when hardware TX csum offloading is enabled - mbufs on RX/TX ring are freed in em_stop(), i.e. during "ifconfig emX down" - TX pattern is adjusted that we test number of avaiable TX descs before dequeuing mbuf from ifq. We also reserve double spare TX descs for 82544 cards on PCI-X bus, so we will not need to unload the loaded mbuf in the mid way due to short of TX descs; this at least makes the logic a little bit simpler. --- diff --git a/sys/conf/files b/sys/conf/files index 605e4fede2..d374e1ccae 100644 --- a/sys/conf/files +++ b/sys/conf/files @@ -220,7 +220,20 @@ dev/netif/ep/if_ep_isa.c optional ep isa dev/netif/ep/if_ep_eisa.c optional ep eisa dev/netif/ep/if_ep_pccard.c optional ep pccard dev/netif/em/if_em.c optional em -dev/netif/em/if_em_hw.c optional em +dev/netif/ig_hal/e1000_80003es2lan.c optional ig_hal +dev/netif/ig_hal/e1000_82540.c optional ig_hal +dev/netif/ig_hal/e1000_82541.c optional ig_hal +dev/netif/ig_hal/e1000_82542.c optional ig_hal +dev/netif/ig_hal/e1000_82543.c optional ig_hal +dev/netif/ig_hal/e1000_82571.c optional ig_hal +dev/netif/ig_hal/e1000_82575.c optional ig_hal +dev/netif/ig_hal/e1000_api.c optional ig_hal +dev/netif/ig_hal/e1000_ich8lan.c optional ig_hal +dev/netif/ig_hal/e1000_mac.c optional ig_hal +dev/netif/ig_hal/e1000_manage.c optional ig_hal +dev/netif/ig_hal/e1000_nvm.c optional ig_hal +dev/netif/ig_hal/e1000_osdep.c optional ig_hal +dev/netif/ig_hal/e1000_phy.c optional ig_hal dev/atm/en/midway.c optional en dev/netif/et/if_et.c optional et dev/netif/ex/if_ex.c optional ex diff --git a/sys/config/GENERIC b/sys/config/GENERIC index 2747cd92db..b6d503f74a 100644 --- a/sys/config/GENERIC +++ b/sys/config/GENERIC @@ -205,10 +205,13 @@ device ppi # Parallel port interface device # PCI Ethernet NICs. device de # DEC/Intel DC21x4x (``Tulip'') -device em # Intel PRO/1000 adapter Gigabit Ethernet Card (``Wiseman'') device txp # 3Com 3cR990 (``Typhoon'') device vx # 3Com 3c590, 3c595 (``Vortex'') +device em # Intel PRO/1000 adapter Gigabit Ethernet Card (``Wiseman'') + # Requires ig_hal +device ig_hal # Intel PRO/1000 hardware abstraction layer + # PCI Ethernet NICs that use the common MII bus controller code. # NOTE: Be sure to keep the 'device miibus' line in order to use these NICs! device miibus # MII bus support diff --git a/sys/config/JG64 b/sys/config/JG64 index 76dd061496..a23df8c48d 100644 --- a/sys/config/JG64 +++ b/sys/config/JG64 @@ -204,10 +204,13 @@ device sio3 at isa? disable port IO_COM4 irq 9 # PCI Ethernet NICs. device de # DEC/Intel DC21x4x (``Tulip'') -device em # Intel PRO/1000 adapter Gigabit Ethernet Card (``Wiseman'') device txp # 3Com 3cR990 (``Typhoon'') device vx # 3Com 3c590, 3c595 (``Vortex'') +device em # Intel PRO/1000 adapter Gigabit Ethernet Card (``Wiseman'') + # Requires ig_hal +device ig_hal # Intel PRO/1000 hardware abstraction layer + # PCI Ethernet NICs that use the common MII bus controller code. # NOTE: Be sure to keep the 'device miibus' line in order to use these NICs! device miibus # MII bus support diff --git a/sys/config/LINT b/sys/config/LINT index bc3e8ee7e7..5026f986e3 100644 --- a/sys/config/LINT +++ b/sys/config/LINT @@ -1969,6 +1969,7 @@ device vx # 3Com 3c590, 3c595 (``Vortex'') # Gigabit Ethernet NICs. device bge # Broadcom BCM570x (``Tigon III'') device em # Intel Pro/1000 (82542,82543,82544,82540) +device ig_hal # Intel Pro/1000 hardware abstraction layer device et # Agere ET1310 10/100/1000 Ethernet device lge # Level 1 LXT1001 (``Mercury'') device nfe # nVidia nForce2/3 MCP04/51/55 CK804 diff --git a/sys/dev/netif/Makefile b/sys/dev/netif/Makefile index 8221da398e..918bd2db41 100644 --- a/sys/dev/netif/Makefile +++ b/sys/dev/netif/Makefile @@ -4,6 +4,6 @@ SUBDIR= an acx age ale ar ath aue axe bce bfe bge bwi cue dc ed em ep et fwe \ fxp iwi iwl jme kue lge lnc mii_layer my msk nfe nge pcn ral re rl \ rtw rue rum sbni sbsh sf sis sk sln sr ste stge ti tl tx txp ural vge \ - vr vx wb wi xe xl + vr vx wb wi xe xl ig_hal .include diff --git a/sys/dev/netif/em/Makefile b/sys/dev/netif/em/Makefile index b9922d1292..821a180bb2 100644 --- a/sys/dev/netif/em/Makefile +++ b/sys/dev/netif/em/Makefile @@ -2,17 +2,16 @@ #$DragonFly: src/sys/dev/netif/em/Makefile,v 1.10 2008/09/17 08:51:29 sephe Exp $ KMOD= if_em -SRCS= if_em.c if_em_hw.c +SRCS= if_em.c SRCS+= device_if.h bus_if.h pci_if.h -SRCS+= opt_polling.h opt_inet.h opt_ktr.h opt_serializer.h +SRCS+= opt_polling.h opt_ktr.h opt_serializer.h + +KMODDEPS = ig_hal .ifndef BUILDING_WITH_KERNEL opt_polling.h: echo '#define DEVICE_POLLING 1' > ${.OBJDIR}/${.TARGET} -opt_inet.h: - echo "#define INET 1" > ${.OBJDIR}/${.TARGET} - opt_serializer.h: touch ${.OBJDIR}/${.TARGET} .endif diff --git a/sys/dev/netif/em/README b/sys/dev/netif/em/README deleted file mode 100644 index 615d078d21..0000000000 --- a/sys/dev/netif/em/README +++ /dev/null @@ -1,383 +0,0 @@ -$DragonFly: src/sys/dev/netif/em/README,v 1.8 2008/03/16 15:50:22 hasso Exp $ -FreeBSD* Driver for the Intel(R) PRO/1000 Family of Adapters -============================================================ - -September 25, 2006 - - -Contents -======== - -- Overview -- Identifying Your Adapter -- Building and Installation -- Speed and Duplex Configuration -- Additional Configurations -- Known Limitations -- Support -- License - - -Overview -======== - -This file describes the FreeBSD* driver for the Intel(R) PRO/1000 Family of -Adapters. This driver has been developed for use with FreeBSD, Release 6.x. - -For questions related to hardware requirements, refer to the documentation -supplied with your Intel PRO/1000 adapter. All hardware requirements listed -apply to use with FreeBSD. - - -Identifying Your Adapter -======================== - -For information on how to identify your adapter, go to the Adapter & -Driver ID Guide at: - -http://support.intel.com/support/network/sb/cs-012904.htm - - -For the latest Intel network drivers for FreeBSD, see: - -http://downloadfinder.intel.com/scripts-df-external/support_intel.aspx - - -NOTE: Mobile adapters are not fully supported. -NOTE: The Intel(R) 82562v 10/100 Network Connection only provides 10/100 -support. - - -Building and Installation -========================= - -NOTE: The driver can be installed as a dynamic loadable kernel module or - compiled into the kernel. You must have kernel sources installed in - order to compile the driver module. - -In the instructions below, x.x.x is the driver version as indicated in the -name of the driver tar file. - -1. Move the base driver tar file to the directory of your choice. For - example, use /home/username/em or /usr/local/src/em. - -2. Untar/unzip the archive: - - tar xvfz em-x.x.x.tar.gz - - This will create an em-x.x.x directory. - -3. To create a loadable module, perform the following steps. - NOTE: To compile the driver into the kernel, go directly to step 4. - - a. To compile the module - - cd em-x.x.x - make - - b. To install the compiled module in system directory: - - make install - - c. If you want the driver to load automatically when the system is booted: - - 1. Edit /boot/loader.conf, and add the following line: - - if_em_load="YES" - -4. To compile the driver into the kernel: - - cd em-x.x.x/src - - cp if_em* /usr/src/sys/dev/em - - cp Makefile.kernel /usr/src/sys/modules/em/Makefile - - Edit the /usr/src/sys/conf/files file, and add the following lines only if - they don't already exist: - - dev/em/if_em.c optional em - - dev/em/if_em_hw.c optional em - - Remove the following lines from the /usr/src/sys/conf/files file, - if they exist: - - dev/em/if_em_fxhw.c optional em - dev/em/if_em_phy.c optional em - - Edit the kernel configuration file (i.e., GENERIC or MYKERNEL) in - /usr/src/sys/config, and ensure the following line is present: - - device em - - Compile and install the kernel. The system must be rebooted for the kernel - updates to take effect. For additional information on compiling the - kernel, consult the FreeBSD operating system documentation. - -5. To assign an IP address to the interface, enter the following: - - ifconfig em - -6. Verify that the interface works. Enter the following, where - is the IP address for another machine on the same subnet as the interface - that is being tested: - - ping - -7. To configure the IP address to remain after reboot, edit /etc/rc.conf, - and create the appropriate ifconfig_ementry: - - ifconfig_em="" - - Example usage: - - ifconfig_em0="inet 192.168.10.1 netmask 255.255.255.0" - - NOTE: For assistance, see the ifconfig man page. - - -Speed and Duplex Configuration -============================== - -By default, the adapter auto-negotiates the speed and duplex of the -connection. If there is a specific need, the ifconfig utility can be used to -configure the speed and duplex settings on the adapter. Example usage: - - ifconfig em media 100baseTX mediaopt - full-duplex - - NOTE: Only use mediaopt to set the driver to full-duplex. If mediaopt is - not specified and you are not running at gigabit speed, the driver - defaults to half-duplex. - - -This driver supports the following media type options: - - autoselect - Enables auto-negotiation for speed and duplex. - - 10baseT/UTP - Sets speed to 10 Mbps. Use the ifconfig mediaopt - option to select full-duplex mode. - - 100baseTX - Sets speed to 100 Mbps. Use the ifconfig mediaopt - option to select full-duplex mode. - - 1000baseT - Sets speed to 1000 Mbps. In this case, the driver - supports only full-duplex mode. - - 1000baseSX - Sets speed to 1000 Mbps. In this case, the driver - supports only full-duplex mode. - -For more information on the ifconfig utility, see the ifconfig man page. - - -Additional Configurations -========================= - -The driver supports Transmit/Receive Checksum Offload and Jumbo Frames on -all but the 82542-based adapters. For specific adapters, refer to the -Identifying Your Adapter section. - - Jumbo Frames - ------------ - To enable Jumbo Frames, use the ifconfig utility to set the Maximum - Transport Unit (MTU) frame size above its default of 1500 bytes. - - The Jumbo Frames MTU range for Intel Adapters is 1500 to 16110. To modify - the setting, enter the following: - - ifconfig em mtu 9000 - - To confirm the MTU used between two specific devices, use: - - route get - - Notes: - - - Only enable Jumbo Frames if your network infrastructure supports them. - - - To enable Jumbo Frames, increase the MTU size on the interface beyond - 1500. - - - The Jumbo Frames setting on the switch must be set to at least 22 bytes - larger than that of the MTU. - - - The maximum MTU setting for Jumbo Frames is 16110. This value coincides - with the maximum Jumbo Frames size of 16128. - - - Some Intel gigabit adapters that support Jumbo Frames have a frame size - limit of 9238 bytes, with a corresponding MTU size limit of 9216 bytes. - The adapters with this limitation are based on the Intel(R) 82571EB, - 82572EI, 82573L and 80003ES2LAN controller. These correspond to the - following product names: - Intel(R) PRO/1000 PT Server Adapter - Intel(R) PRO/1000 PT Desktop Adapter - Intel(R) PRO/1000 PT Network Connection - Intel(R) PRO/1000 PT Dual Port Server Adapter - Intel(R) PRO/1000 PT Dual Port Network Connection - Intel(R) PRO/1000 PF Server Adapter - Intel(R) PRO/1000 PF Network Connection - Intel(R) PRO/1000 PF Dual Port Server Adapter - Intel(R) PRO/1000 PB Server Connection - Intel(R) PRO/1000 PL Network Connection - Intel(R) PRO/1000 EB Network Connection with I/O Acceleration - Intel(R) PRO/1000 EB Backplane Connection with I/O Acceleration - - - Adapters based on the Intel(R) 82542 and 82573V/E controller do not - support Jumbo Frames. These correspond to the following product names: - Intel(R) PRO/1000 Gigabit Server Adapter - Intel(R) PRO/1000 PM Network Connection - - - Using Jumbo Frames at 10 or 100 Mbps may result in poor performance or - loss of link. - - - The following adapters to not support Jumbo Frames: - Intel(R) 82562V 10/100 Network Connection - Intel(R) 82566DM Gigabit Network Connection - Intel(R) 82566DC Gigabit Network Connection - Intel(R) 82566MM Gigabit Network Connection - Intel(R) 82566MC Gigabit Network Connection - - - VLANs - ----- - To create a new VLAN interface: - - ifconfig create - - To associate the VLAN interface with a physical interface and - assign a VLAN ID, IP address, and netmask: - - ifconfig netmask vlan - vlandev - - Example: - - ifconfig vlan10 10.0.0.1 netmask 255.255.255.0 vlan10 vlandev em0 - - In this example, all packets will be marked on egress with 802.1Q VLAN - tags, specifying a VLAN ID of 10. - - To remove a VLAN interface: - - ifconfig destroy - - Polling - ------- - NOTES: DEVICE POLLING is only valid for non-SMP (Symmetric MultiProcessing) - kernels. - - The driver has to be compiled into the kernel for DEVICE POLLING to be - enabled in the driver. - - To enable polling in the driver, add the following options to the kernel - configuration, and then recompile the kernel: - - options DEVICE_POLLING - - At runtime use: - sysctl kern.polling.enable=1 - ifconfig polling - to turn polling on - - Use: - sysctl kern.polling.enable=0 - or - ifconfig -polling - to turn polling off - - Checksum Offload - ---------------- - Checksum offloading is not supported on 82542 Gigabit adapters. - - Checksum offloading supports both TCP and UDP packets and is - supported for both transmit and receive. - - Checksum offloading can be enabled or disabled using ifconfig. - Both transmit and receive offloading will be either enabled or - disabled together. You cannot enable/disable one without the other. - - To enable checksum offloading: - - ifconfig rxcsum - - To disable checksum offloading: - - ifconfig -rxcsum - - To confirm the current setting: - - ifconfig - - Look for the presence or absence of the following line: - - options=3 - - See the ifconfig man page for further information. - - -Known Limitations -================= - - In FreeBSD version 4.x with Symmetric MultiProcessing (SMP), there is a known - issue on some newer hardware. The problem is generic kernel and only in SMP - mode. The workaround is to either use FreeBSD version 4.x in single processor - mode, or use FreeBSD 5.4 or later. - - There are known performance issues with this driver when running UDP traffic - with Jumbo Frames. - - There is a known compatibility issue where time to link is slow or link is not - established between 82541/82547 controllers and some switches. Known switches - include: - Planex FXG-08TE - I-O Data ETG-SH8 - - The driver can be compiled with the following changes: - - Edit ./em.x.x.x/src/if_em.h to uncomment the #define EM_MASTER_SLAVE - from within the comments. For example, change from: - - /* #define EM_MASTER_SLAVE 2 */ - to: - #define EM_MASTER_SLAVE 2 - - Use one of the following options: - 1 = Master mode - 2 = Slave mode - 3 = Auto master/slave - Setting 2 is recommended. - - Recompile the module: - a. To compile the module - cd em-x.x.x - make clean - make - - b. To install the compiled module in system directory: - make install - - -Support -======= - -For general information and support, go to the Intel support website at: - - http://support.intel.com - -If an issue is identified, support is through email only at: -freebsdnic@mailbox.intel.com - - -License -======= - -This software program is released under the terms of a license agreement -between you ('Licensee') and Intel. Do not use or load this software or any -associated materials (collectively, the 'Software') until you have carefully -read the full terms and conditions of the LICENSE located in this software -package. By loading or using the Software, you agree to the terms of this -Agreement. If you do not agree with the terms of this Agreement, do not -install or use the Software. - -* Other names and brands may be claimed as the property of others. diff --git a/sys/dev/netif/em/if_em.c b/sys/dev/netif/em/if_em.c index f170c7ac70..f0db375a4d 100644 --- a/sys/dev/netif/em/if_em.c +++ b/sys/dev/netif/em/if_em.c @@ -1,24 +1,23 @@ /* - * * Copyright (c) 2004 Joerg Sonnenberger . All rights reserved. * - * Copyright (c) 2001-2006, Intel Corporation + * Copyright (c) 2001-2008, Intel Corporation * All rights reserved. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions are met: - * + * * 1. Redistributions of source code must retain the above copyright notice, * this list of conditions and the following disclaimer. - * + * * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the distribution. - * + * * 3. Neither the name of the Intel Corporation nor the names of its * contributors may be used to endorse or promote products derived from * this software without specific prior written permission. - * + * * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE @@ -33,14 +32,14 @@ * * * Copyright (c) 2005 The DragonFly Project. All rights reserved. - * + * * This code is derived from software contributed to The DragonFly Project * by Matthew Dillon - * + * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: - * + * * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright @@ -50,7 +49,7 @@ * 3. Neither the name of The DragonFly Project nor the names of its * contributors may be used to endorse or promote products derived * from this software without specific, prior written permission. - * + * * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS * ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS @@ -63,16 +62,15 @@ * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT * OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF * SUCH DAMAGE. - * + * * $DragonFly: src/sys/dev/netif/em/if_em.c,v 1.80 2008/09/17 08:51:29 sephe Exp $ - * $FreeBSD$ */ /* * SERIALIZATION API RULES: * * - If the driver uses the same serializer for the interrupt as for the * ifnet, most of the serialization will be done automatically for the - * driver. + * driver. * * - ifmedia entry points will be serialized by the ifmedia code using the * ifnet serializer. @@ -84,9 +82,12 @@ * installed by the device driver. * * - The device driver typically holds the serializer at the time it wishes - * to call if_input. If so, it should pass the serializer to if_input and - * note that the serializer might be dropped temporarily by if_input - * (e.g. in case it has to bridge the packet to another interface). + * to call if_input. + * + * - We must call lwkt_serialize_handler_enable() prior to enabling the + * hardware interrupt and lwkt_serialize_handler_disable() after disabling + * the hardware interrupt in order to avoid handler execution races from + * scheduled interrupt threads. * * NOTE! Since callers into the device driver hold the ifnet serializer, * the device driver may be holding a serializer at the time it calls @@ -94,7 +95,6 @@ */ #include "opt_polling.h" -#include "opt_inet.h" #include "opt_serializer.h" #include @@ -105,12 +105,13 @@ #include #include #include -#include +#include #include #include #include #include #include +#include #include #include @@ -118,266 +119,255 @@ #include #include #include -#include #include #include #include -#ifdef INET -#include #include -#include +#include #include +#include #include #include -#endif - -#include -#include -#define EM_X60_WORKAROUND - -/********************************************************************* - * Set this to one to display debug statistics - *********************************************************************/ -int em_display_debug_stats = 0; - -/********************************************************************* - * Driver version - *********************************************************************/ - -char em_driver_version[] = "6.2.9"; +#include +#include +#include +#include +#include -/********************************************************************* - * PCI Device ID Table - * - * Used by probe to select devices to load on - * Last field stores an index into em_strings - * Last entry must be all 0s - * - * { Vendor ID, Device ID, SubVendor ID, SubDevice ID, String Index } - *********************************************************************/ +#define EM_NAME "Intel(R) PRO/1000 Network Connection " +#define EM_VER " 6.9.6" + +#define EM_DEVICE(id) \ + { EM_VENDOR_ID, E1000_DEV_ID_##id, EM_NAME #id EM_VER } +#define EM_DEVICE_NULL { 0, 0, NULL } + +static const struct em_vendor_info em_vendor_info_array[] = { + EM_DEVICE(82540EM), + EM_DEVICE(82540EM_LOM), + EM_DEVICE(82540EP), + EM_DEVICE(82540EP_LOM), + EM_DEVICE(82540EP_LP), + + EM_DEVICE(82541EI), + EM_DEVICE(82541ER), + EM_DEVICE(82541ER_LOM), + EM_DEVICE(82541EI_MOBILE), + EM_DEVICE(82541GI), + EM_DEVICE(82541GI_LF), + EM_DEVICE(82541GI_MOBILE), + + EM_DEVICE(82542), + + EM_DEVICE(82543GC_FIBER), + EM_DEVICE(82543GC_COPPER), + + EM_DEVICE(82544EI_COPPER), + EM_DEVICE(82544EI_FIBER), + EM_DEVICE(82544GC_COPPER), + EM_DEVICE(82544GC_LOM), + + EM_DEVICE(82545EM_COPPER), + EM_DEVICE(82545EM_FIBER), + EM_DEVICE(82545GM_COPPER), + EM_DEVICE(82545GM_FIBER), + EM_DEVICE(82545GM_SERDES), + + EM_DEVICE(82546EB_COPPER), + EM_DEVICE(82546EB_FIBER), + EM_DEVICE(82546EB_QUAD_COPPER), + EM_DEVICE(82546GB_COPPER), + EM_DEVICE(82546GB_FIBER), + EM_DEVICE(82546GB_SERDES), + EM_DEVICE(82546GB_PCIE), + EM_DEVICE(82546GB_QUAD_COPPER), + EM_DEVICE(82546GB_QUAD_COPPER_KSP3), + + EM_DEVICE(82547EI), + EM_DEVICE(82547EI_MOBILE), + EM_DEVICE(82547GI), + + EM_DEVICE(82571EB_COPPER), + EM_DEVICE(82571EB_FIBER), + EM_DEVICE(82571EB_SERDES), + EM_DEVICE(82571EB_SERDES_DUAL), + EM_DEVICE(82571EB_SERDES_QUAD), + EM_DEVICE(82571EB_QUAD_COPPER), + EM_DEVICE(82571EB_QUAD_COPPER_LP), + EM_DEVICE(82571EB_QUAD_FIBER), + EM_DEVICE(82571PT_QUAD_COPPER), + + EM_DEVICE(82572EI_COPPER), + EM_DEVICE(82572EI_FIBER), + EM_DEVICE(82572EI_SERDES), + EM_DEVICE(82572EI), + + EM_DEVICE(82573E), + EM_DEVICE(82573E_IAMT), + EM_DEVICE(82573L), + + EM_DEVICE(80003ES2LAN_COPPER_SPT), + EM_DEVICE(80003ES2LAN_SERDES_SPT), + EM_DEVICE(80003ES2LAN_COPPER_DPT), + EM_DEVICE(80003ES2LAN_SERDES_DPT), + + EM_DEVICE(ICH8_IGP_M_AMT), + EM_DEVICE(ICH8_IGP_AMT), + EM_DEVICE(ICH8_IGP_C), + EM_DEVICE(ICH8_IFE), + EM_DEVICE(ICH8_IFE_GT), + EM_DEVICE(ICH8_IFE_G), + EM_DEVICE(ICH8_IGP_M), + + EM_DEVICE(ICH9_IGP_M_AMT), + EM_DEVICE(ICH9_IGP_AMT), + EM_DEVICE(ICH9_IGP_C), + EM_DEVICE(ICH9_IGP_M), + EM_DEVICE(ICH9_IGP_M_V), + EM_DEVICE(ICH9_IFE), + EM_DEVICE(ICH9_IFE_GT), + EM_DEVICE(ICH9_IFE_G), + EM_DEVICE(ICH9_BM), + + EM_DEVICE(82574L), + + EM_DEVICE(ICH10_R_BM_LM), + EM_DEVICE(ICH10_R_BM_LF), + EM_DEVICE(ICH10_R_BM_V), + EM_DEVICE(ICH10_D_BM_LM), + EM_DEVICE(ICH10_D_BM_LF), -static em_vendor_info_t em_vendor_info_array[] = -{ - /* Intel(R) PRO/1000 Network Connection */ - { 0x8086, E1000_DEV_ID_82540EM, PCI_ANY_ID, PCI_ANY_ID, 0}, - { 0x8086, E1000_DEV_ID_82540EM_LOM, PCI_ANY_ID, PCI_ANY_ID, 0}, - { 0x8086, E1000_DEV_ID_82540EP, PCI_ANY_ID, PCI_ANY_ID, 0}, - { 0x8086, E1000_DEV_ID_82540EP_LOM, PCI_ANY_ID, PCI_ANY_ID, 0}, - { 0x8086, E1000_DEV_ID_82540EP_LP, PCI_ANY_ID, PCI_ANY_ID, 0}, - - { 0x8086, E1000_DEV_ID_82541EI, PCI_ANY_ID, PCI_ANY_ID, 0}, - { 0x8086, E1000_DEV_ID_82541ER, PCI_ANY_ID, PCI_ANY_ID, 0}, - { 0x8086, E1000_DEV_ID_82541ER_LOM, PCI_ANY_ID, PCI_ANY_ID, 0}, - { 0x8086, E1000_DEV_ID_82541EI_MOBILE, PCI_ANY_ID, PCI_ANY_ID, 0}, - { 0x8086, E1000_DEV_ID_82541GI, PCI_ANY_ID, PCI_ANY_ID, 0}, - { 0x8086, E1000_DEV_ID_82541GI_LF, PCI_ANY_ID, PCI_ANY_ID, 0}, - { 0x8086, E1000_DEV_ID_82541GI_MOBILE, PCI_ANY_ID, PCI_ANY_ID, 0}, - - { 0x8086, E1000_DEV_ID_82542, PCI_ANY_ID, PCI_ANY_ID, 0}, - - { 0x8086, E1000_DEV_ID_82543GC_FIBER, PCI_ANY_ID, PCI_ANY_ID, 0}, - { 0x8086, E1000_DEV_ID_82543GC_COPPER, PCI_ANY_ID, PCI_ANY_ID, 0}, - - { 0x8086, E1000_DEV_ID_82544EI_COPPER, PCI_ANY_ID, PCI_ANY_ID, 0}, - { 0x8086, E1000_DEV_ID_82544EI_FIBER, PCI_ANY_ID, PCI_ANY_ID, 0}, - { 0x8086, E1000_DEV_ID_82544GC_COPPER, PCI_ANY_ID, PCI_ANY_ID, 0}, - { 0x8086, E1000_DEV_ID_82544GC_LOM, PCI_ANY_ID, PCI_ANY_ID, 0}, - - { 0x8086, E1000_DEV_ID_82545EM_COPPER, PCI_ANY_ID, PCI_ANY_ID, 0}, - { 0x8086, E1000_DEV_ID_82545EM_FIBER, PCI_ANY_ID, PCI_ANY_ID, 0}, - { 0x8086, E1000_DEV_ID_82545GM_COPPER, PCI_ANY_ID, PCI_ANY_ID, 0}, - { 0x8086, E1000_DEV_ID_82545GM_FIBER, PCI_ANY_ID, PCI_ANY_ID, 0}, - { 0x8086, E1000_DEV_ID_82545GM_SERDES, PCI_ANY_ID, PCI_ANY_ID, 0}, - - { 0x8086, E1000_DEV_ID_82546EB_COPPER, PCI_ANY_ID, PCI_ANY_ID, 0}, - { 0x8086, E1000_DEV_ID_82546EB_FIBER, PCI_ANY_ID, PCI_ANY_ID, 0}, - { 0x8086, E1000_DEV_ID_82546EB_QUAD_COPPER, PCI_ANY_ID, PCI_ANY_ID, 0}, - { 0x8086, E1000_DEV_ID_82546GB_COPPER, PCI_ANY_ID, PCI_ANY_ID, 0}, - { 0x8086, E1000_DEV_ID_82546GB_FIBER, PCI_ANY_ID, PCI_ANY_ID, 0}, - { 0x8086, E1000_DEV_ID_82546GB_SERDES, PCI_ANY_ID, PCI_ANY_ID, 0}, - { 0x8086, E1000_DEV_ID_82546GB_PCIE, PCI_ANY_ID, PCI_ANY_ID, 0}, - { 0x8086, E1000_DEV_ID_82546GB_QUAD_COPPER, PCI_ANY_ID, PCI_ANY_ID, 0}, - { 0x8086, E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3, - PCI_ANY_ID, PCI_ANY_ID, 0}, - - { 0x8086, E1000_DEV_ID_82547EI, PCI_ANY_ID, PCI_ANY_ID, 0}, - { 0x8086, E1000_DEV_ID_82547EI_MOBILE, PCI_ANY_ID, PCI_ANY_ID, 0}, - { 0x8086, E1000_DEV_ID_82547GI, PCI_ANY_ID, PCI_ANY_ID, 0}, - - { 0x8086, E1000_DEV_ID_82571EB_COPPER, PCI_ANY_ID, PCI_ANY_ID, 0}, - { 0x8086, E1000_DEV_ID_82571EB_FIBER, PCI_ANY_ID, PCI_ANY_ID, 0}, - { 0x8086, E1000_DEV_ID_82571EB_SERDES, PCI_ANY_ID, PCI_ANY_ID, 0}, - { 0x8086, E1000_DEV_ID_82571EB_QUAD_COPPER, - PCI_ANY_ID, PCI_ANY_ID, 0}, - { 0x8086, E1000_DEV_ID_82571EB_QUAD_COPPER_LOWPROFILE, - PCI_ANY_ID, PCI_ANY_ID, 0}, - - { 0x8086, E1000_DEV_ID_82571EB_QUAD_FIBER, - PCI_ANY_ID, PCI_ANY_ID, 0}, - { 0x8086, E1000_DEV_ID_82571PT_QUAD_COPPER, - PCI_ANY_ID, PCI_ANY_ID, 0}, - { 0x8086, E1000_DEV_ID_82572EI_COPPER, PCI_ANY_ID, PCI_ANY_ID, 0}, - { 0x8086, E1000_DEV_ID_82572EI_FIBER, PCI_ANY_ID, PCI_ANY_ID, 0}, - { 0x8086, E1000_DEV_ID_82572EI_SERDES, PCI_ANY_ID, PCI_ANY_ID, 0}, - { 0x8086, E1000_DEV_ID_82572EI, PCI_ANY_ID, PCI_ANY_ID, 0}, - - { 0x8086, E1000_DEV_ID_82573E, PCI_ANY_ID, PCI_ANY_ID, 0}, - { 0x8086, E1000_DEV_ID_82573E_IAMT, PCI_ANY_ID, PCI_ANY_ID, 0}, - { 0x8086, E1000_DEV_ID_82573L, PCI_ANY_ID, PCI_ANY_ID, 0}, - - { 0x8086, E1000_DEV_ID_80003ES2LAN_COPPER_SPT, - PCI_ANY_ID, PCI_ANY_ID, 0}, - { 0x8086, E1000_DEV_ID_80003ES2LAN_SERDES_SPT, - PCI_ANY_ID, PCI_ANY_ID, 0}, - { 0x8086, E1000_DEV_ID_80003ES2LAN_COPPER_DPT, - PCI_ANY_ID, PCI_ANY_ID, 0}, - { 0x8086, E1000_DEV_ID_80003ES2LAN_SERDES_DPT, - PCI_ANY_ID, PCI_ANY_ID, 0}, - - { 0x8086, E1000_DEV_ID_ICH8_IGP_M_AMT, PCI_ANY_ID, PCI_ANY_ID, 0}, - { 0x8086, E1000_DEV_ID_ICH8_IGP_AMT, PCI_ANY_ID, PCI_ANY_ID, 0}, - { 0x8086, E1000_DEV_ID_ICH8_IGP_C, PCI_ANY_ID, PCI_ANY_ID, 0}, - { 0x8086, E1000_DEV_ID_ICH8_IFE, PCI_ANY_ID, PCI_ANY_ID, 0}, - { 0x8086, E1000_DEV_ID_ICH8_IFE_GT, PCI_ANY_ID, PCI_ANY_ID, 0}, - { 0x8086, E1000_DEV_ID_ICH8_IFE_G, PCI_ANY_ID, PCI_ANY_ID, 0}, - { 0x8086, E1000_DEV_ID_ICH8_IGP_M, PCI_ANY_ID, PCI_ANY_ID, 0}, - - { 0x8086, E1000_DEV_ID_ICH9_IGP_AMT, PCI_ANY_ID, PCI_ANY_ID, 0}, - { 0x8086, E1000_DEV_ID_ICH9_IGP_C, PCI_ANY_ID, PCI_ANY_ID, 0}, - { 0x8086, E1000_DEV_ID_ICH9_IFE, PCI_ANY_ID, PCI_ANY_ID, 0}, - { 0x8086, E1000_DEV_ID_ICH9_IFE_GT, PCI_ANY_ID, PCI_ANY_ID, 0}, - { 0x8086, E1000_DEV_ID_ICH9_IFE_G, PCI_ANY_ID, PCI_ANY_ID, 0}, - - { 0x8086, E1000_DEV_ID_82575EB_COPPER, PCI_ANY_ID, PCI_ANY_ID, 0}, - { 0x8086, E1000_DEV_ID_82575EB_FIBER_SERDES, - PCI_ANY_ID, PCI_ANY_ID, 0}, - { 0x8086, E1000_DEV_ID_82575GB_QUAD_COPPER, - PCI_ANY_ID, PCI_ANY_ID, 0}, - { 0x8086, 0x101A, PCI_ANY_ID, PCI_ANY_ID, 0}, - { 0x8086, 0x1014, PCI_ANY_ID, PCI_ANY_ID, 0}, /* required last entry */ - { 0, 0, 0, 0, 0} -}; - -/********************************************************************* - * Table of branding strings for all supported NICs. - *********************************************************************/ - -static const char *em_strings[] = { - "Intel(R) PRO/1000 Network Connection" + EM_DEVICE_NULL }; -/********************************************************************* - * Function prototypes - *********************************************************************/ static int em_probe(device_t); static int em_attach(device_t); static int em_detach(device_t); static int em_shutdown(device_t); -static void em_intr(void *); static int em_suspend(device_t); static int em_resume(device_t); -static void em_start(struct ifnet *); + +static void em_init(void *); +static void em_stop(struct adapter *); static int em_ioctl(struct ifnet *, u_long, caddr_t, struct ucred *); +static void em_start(struct ifnet *); +#ifdef DEVICE_POLLING +static void em_poll(struct ifnet *, enum poll_cmd, int); +#endif static void em_watchdog(struct ifnet *); -static void em_init(void *); -static void em_stop(void *); static void em_media_status(struct ifnet *, struct ifmediareq *); static int em_media_change(struct ifnet *); -static void em_identify_hardware(struct adapter *); -static int em_allocate_pci_resources(device_t); -static void em_free_pci_resources(device_t); -static void em_local_timer(void *); -static int em_hardware_init(struct adapter *); -static void em_setup_interface(device_t, struct adapter *); -static int em_setup_transmit_structures(struct adapter *); -static void em_initialize_transmit_unit(struct adapter *); -static int em_setup_receive_structures(struct adapter *); -static void em_initialize_receive_unit(struct adapter *); +static void em_timer(void *); + +static void em_intr(void *); +static void em_rxeof(struct adapter *, int); +static void em_txeof(struct adapter *); +static void em_tx_purge(struct adapter *); static void em_enable_intr(struct adapter *); static void em_disable_intr(struct adapter *); -static void em_free_transmit_structures(struct adapter *); -static void em_free_receive_structures(struct adapter *); -static void em_update_stats_counters(struct adapter *); -static void em_txeof(struct adapter *); -static int em_allocate_receive_structures(struct adapter *); -static void em_rxeof(struct adapter *, int); -static void em_receive_checksum(struct adapter *, struct em_rx_desc *, - struct mbuf *); -static void em_transmit_checksum_setup(struct adapter *, struct mbuf *, - uint32_t *, uint32_t *); + +static int em_dma_malloc(struct adapter *, bus_size_t, + struct em_dma_alloc *); +static void em_dma_free(struct adapter *, struct em_dma_alloc *); +static void em_init_tx_ring(struct adapter *); +static int em_init_rx_ring(struct adapter *); +static int em_create_tx_ring(struct adapter *); +static int em_create_rx_ring(struct adapter *); +static void em_destroy_tx_ring(struct adapter *, int); +static void em_destroy_rx_ring(struct adapter *, int); +static int em_newbuf(struct adapter *, int, int); +static int em_encap(struct adapter *, struct mbuf **); +static void em_rxcsum(struct adapter *, struct e1000_rx_desc *, + struct mbuf *); +static void em_txcsum(struct adapter *, struct mbuf *, + uint32_t *, uint32_t *); + +static int em_get_hw_info(struct adapter *); +static int em_is_valid_eaddr(const uint8_t *); +static int em_alloc_pci_res(struct adapter *); +static void em_free_pci_res(struct adapter *); +static int em_hw_init(struct adapter *); +static void em_setup_ifp(struct adapter *); +static void em_init_tx_unit(struct adapter *); +static void em_init_rx_unit(struct adapter *); +static void em_update_stats(struct adapter *); static void em_set_promisc(struct adapter *); static void em_disable_promisc(struct adapter *); static void em_set_multi(struct adapter *); -static void em_print_hw_stats(struct adapter *); static void em_update_link_status(struct adapter *); -static int em_get_buf(int i, struct adapter *, struct mbuf *, int how); -static void em_enable_vlans(struct adapter *); -static void em_disable_vlans(struct adapter *) __unused; -static int em_encap(struct adapter *, struct mbuf *); static void em_smartspeed(struct adapter *); + +/* Hardware workarounds */ static int em_82547_fifo_workaround(struct adapter *, int); static void em_82547_update_fifo_head(struct adapter *, int); static int em_82547_tx_fifo_reset(struct adapter *); static void em_82547_move_tail(void *); static void em_82547_move_tail_serialized(struct adapter *); -static int em_dma_malloc(struct adapter *, bus_size_t, - struct em_dma_alloc *); -static void em_dma_free(struct adapter *, struct em_dma_alloc *); +static uint32_t em_82544_fill_desc(bus_addr_t, uint32_t, PDESC_ARRAY); + static void em_print_debug_info(struct adapter *); -static int em_is_valid_ether_addr(uint8_t *); +static void em_print_nvm_info(struct adapter *); +static void em_print_hw_stats(struct adapter *); + static int em_sysctl_stats(SYSCTL_HANDLER_ARGS); static int em_sysctl_debug_info(SYSCTL_HANDLER_ARGS); -static uint32_t em_fill_descriptors(bus_addr_t address, uint32_t length, - PDESC_ARRAY desc_array); static int em_sysctl_int_delay(SYSCTL_HANDLER_ARGS); static int em_sysctl_int_throttle(SYSCTL_HANDLER_ARGS); +static void em_add_sysctl(struct adapter *adapter); static void em_add_int_delay_sysctl(struct adapter *, const char *, - const char *, - struct em_int_delay_info *, int, int); + const char *, struct em_int_delay_info *, int, int); -/********************************************************************* - * FreeBSD Device Interface Entry Points - *********************************************************************/ +/* Management and WOL Support */ +static void em_get_mgmt(struct adapter *); +static void em_rel_mgmt(struct adapter *); +static void em_get_hw_control(struct adapter *); +static void em_rel_hw_control(struct adapter *); +static void em_enable_wol(device_t); static device_method_t em_methods[] = { /* Device interface */ - DEVMETHOD(device_probe, em_probe), - DEVMETHOD(device_attach, em_attach), - DEVMETHOD(device_detach, em_detach), - DEVMETHOD(device_shutdown, em_shutdown), - DEVMETHOD(device_suspend, em_suspend), - DEVMETHOD(device_resume, em_resume), - {0, 0} + DEVMETHOD(device_probe, em_probe), + DEVMETHOD(device_attach, em_attach), + DEVMETHOD(device_detach, em_detach), + DEVMETHOD(device_shutdown, em_shutdown), + DEVMETHOD(device_suspend, em_suspend), + DEVMETHOD(device_resume, em_resume), + { 0, 0 } }; static driver_t em_driver = { - "em", em_methods, sizeof(struct adapter), + "em", + em_methods, + sizeof(struct adapter), }; static devclass_t em_devclass; DECLARE_DUMMY_MODULE(if_em); +MODULE_DEPEND(em, ig_hal, 1, 1, 1); DRIVER_MODULE(if_em, pci, em_driver, em_devclass, 0, 0); /********************************************************************* * Tunable default values. *********************************************************************/ -#define E1000_TICKS_TO_USECS(ticks) ((1024 * (ticks) + 500) / 1000) -#define E1000_USECS_TO_TICKS(usecs) ((1000 * (usecs) + 512) / 1024) +#define EM_TICKS_TO_USECS(ticks) ((1024 * (ticks) + 500) / 1000) +#define EM_USECS_TO_TICKS(usecs) ((1000 * (usecs) + 512) / 1024) + +static int em_tx_int_delay_dflt = EM_TICKS_TO_USECS(EM_TIDV); +static int em_rx_int_delay_dflt = EM_TICKS_TO_USECS(EM_RDTR); +static int em_tx_abs_int_delay_dflt = EM_TICKS_TO_USECS(EM_TADV); +static int em_rx_abs_int_delay_dflt = EM_TICKS_TO_USECS(EM_RADV); +static int em_int_throttle_ceil = EM_DEFAULT_ITR; +static int em_rxd = EM_DEFAULT_RXD; +static int em_txd = EM_DEFAULT_TXD; +static int em_smart_pwr_down = FALSE; -static int em_tx_int_delay_dflt = E1000_TICKS_TO_USECS(EM_TIDV); -static int em_rx_int_delay_dflt = E1000_TICKS_TO_USECS(EM_RDTR); -static int em_tx_abs_int_delay_dflt = E1000_TICKS_TO_USECS(EM_TADV); -static int em_rx_abs_int_delay_dflt = E1000_TICKS_TO_USECS(EM_RADV); -static int em_int_throttle_ceil = 10000; -static int em_rxd = EM_DEFAULT_RXD; -static int em_txd = EM_DEFAULT_TXD; -static int em_smart_pwr_down = FALSE; +/* Controls whether promiscuous also shows bad packets */ +static int em_debug_sbp = FALSE; TUNABLE_INT("hw.em.tx_int_delay", &em_tx_int_delay_dflt); TUNABLE_INT("hw.em.rx_int_delay", &em_rx_int_delay_dflt); @@ -387,10 +377,14 @@ TUNABLE_INT("hw.em.int_throttle_ceil", &em_int_throttle_ceil); TUNABLE_INT("hw.em.rxd", &em_rxd); TUNABLE_INT("hw.em.txd", &em_txd); TUNABLE_INT("hw.em.smart_pwr_down", &em_smart_pwr_down); +TUNABLE_INT("hw.em.sbp", &em_debug_sbp); + +/* Global used in WOL setup with multiport cards */ +static int em_global_quad_port_a = 0; + +/* Set this to one to display debug statistics */ +static int em_display_debug_stats = 0; -/* - * Kernel trace for characterization of operations - */ #if !defined(KTR_IF_EM) #define KTR_IF_EM KTR_ALL #endif @@ -402,439 +396,529 @@ KTR_INFO(KTR_IF_EM, if_em, pkt_txqueue, 5, "tx packet", 0); KTR_INFO(KTR_IF_EM, if_em, pkt_txclean, 6, "tx clean", 0); #define logif(name) KTR_LOG(if_em_ ## name) -/********************************************************************* - * Device identification routine - * - * em_probe determines if the driver should be loaded on - * adapter based on PCI vendor/device id of the adapter. - * - * return 0 on success, positive on failure - *********************************************************************/ - static int em_probe(device_t dev) { - em_vendor_info_t *ent; - - uint16_t pci_vendor_id = 0; - uint16_t pci_device_id = 0; - uint16_t pci_subvendor_id = 0; - uint16_t pci_subdevice_id = 0; - char adapter_name[60]; + const struct em_vendor_info *ent; + uint16_t vid, did; - INIT_DEBUGOUT("em_probe: begin"); + vid = pci_get_vendor(dev); + did = pci_get_device(dev); - pci_vendor_id = pci_get_vendor(dev); - if (pci_vendor_id != EM_VENDOR_ID) - return (ENXIO); - - pci_device_id = pci_get_device(dev); - pci_subvendor_id = pci_get_subvendor(dev); - pci_subdevice_id = pci_get_subdevice(dev); - - ent = em_vendor_info_array; - while (ent->vendor_id != 0) { - if ((pci_vendor_id == ent->vendor_id) && - (pci_device_id == ent->device_id) && - - ((pci_subvendor_id == ent->subvendor_id) || - (ent->subvendor_id == PCI_ANY_ID)) && - - ((pci_subdevice_id == ent->subdevice_id) || - (ent->subdevice_id == PCI_ANY_ID))) { - ksnprintf(adapter_name, sizeof(adapter_name), - "%s, Version - %s", em_strings[ent->index], - em_driver_version); - device_set_desc_copy(dev, adapter_name); + for (ent = em_vendor_info_array; ent->desc != NULL; ++ent) { + if (vid == ent->vendor_id && did == ent->device_id) { + device_set_desc(dev, ent->desc); device_set_async_attach(dev, TRUE); return (0); } - ent++; } - return (ENXIO); } -/********************************************************************* - * Device initialization routine - * - * The attach entry point is called when the driver is being loaded. - * This routine identifies the type of hardware, allocates all resources - * and initializes the hardware. - * - * return 0 on success, positive on failure - *********************************************************************/ - static int em_attach(device_t dev) { - struct adapter *adapter; - struct ifnet *ifp; + struct adapter *adapter = device_get_softc(dev); + struct ifnet *ifp = &adapter->arpcom.ac_if; int tsize, rsize; int error = 0; + uint16_t eeprom_data, device_id; - INIT_DEBUGOUT("em_attach: begin"); - - adapter = device_get_softc(dev); - ifp = &adapter->interface_data.ac_if; + adapter->dev = adapter->osdep.dev = dev; callout_init(&adapter->timer); callout_init(&adapter->tx_fifo_timer); - adapter->dev = dev; - adapter->osdep.dev = dev; - - /* SYSCTL stuff */ - sysctl_ctx_init(&adapter->sysctl_ctx); - adapter->sysctl_tree = SYSCTL_ADD_NODE(&adapter->sysctl_ctx, - SYSCTL_STATIC_CHILDREN(_hw), - OID_AUTO, - device_get_nameunit(dev), - CTLFLAG_RD, - 0, ""); - - if (adapter->sysctl_tree == NULL) { - device_printf(dev, "Unable to create sysctl tree\n"); - return EIO; + /* Determine hardware and mac info */ + error = em_get_hw_info(adapter); + if (error) { + device_printf(dev, "Identify hardware failed\n"); + goto fail; } - SYSCTL_ADD_PROC(&adapter->sysctl_ctx, - SYSCTL_CHILDREN(adapter->sysctl_tree), - OID_AUTO, "debug_info", CTLTYPE_INT|CTLFLAG_RW, - (void *)adapter, 0, - em_sysctl_debug_info, "I", "Debug Information"); + /* Setup PCI resources */ + error = em_alloc_pci_res(adapter); + if (error) { + device_printf(dev, "Allocation of PCI resources failed\n"); + goto fail; + } - SYSCTL_ADD_PROC(&adapter->sysctl_ctx, - SYSCTL_CHILDREN(adapter->sysctl_tree), - OID_AUTO, "stats", CTLTYPE_INT|CTLFLAG_RW, - (void *)adapter, 0, - em_sysctl_stats, "I", "Statistics"); + /* + * For ICH8 and family we need to map the flash memory, + * and this must happen after the MAC is identified. + */ + if (adapter->hw.mac.type == e1000_ich8lan || + adapter->hw.mac.type == e1000_ich10lan || + adapter->hw.mac.type == e1000_ich9lan) { + adapter->flash_rid = EM_BAR_FLASH; + + adapter->flash = bus_alloc_resource_any(dev, SYS_RES_MEMORY, + &adapter->flash_rid, RF_ACTIVE); + if (adapter->flash == NULL) { + device_printf(dev, "Mapping of Flash failed\n"); + error = ENXIO; + goto fail; + } + adapter->osdep.flash_bus_space_tag = + rman_get_bustag(adapter->flash); + adapter->osdep.flash_bus_space_handle = + rman_get_bushandle(adapter->flash); - /* Determine hardware revision */ - em_identify_hardware(adapter); + /* + * This is used in the shared code + * XXX this goof is actually not used. + */ + adapter->hw.flash_address = (uint8_t *)adapter->flash; + } - /* Set up some sysctls for the tunable interrupt delays */ - em_add_int_delay_sysctl(adapter, "rx_int_delay", - "receive interrupt delay in usecs", - &adapter->rx_int_delay, - E1000_REG_OFFSET(&adapter->hw, RDTR), - em_rx_int_delay_dflt); - em_add_int_delay_sysctl(adapter, "tx_int_delay", - "transmit interrupt delay in usecs", - &adapter->tx_int_delay, - E1000_REG_OFFSET(&adapter->hw, TIDV), - em_tx_int_delay_dflt); - if (adapter->hw.mac_type >= em_82540) { - em_add_int_delay_sysctl(adapter, "rx_abs_int_delay", - "receive interrupt delay limit in usecs", - &adapter->rx_abs_int_delay, - E1000_REG_OFFSET(&adapter->hw, RADV), - em_rx_abs_int_delay_dflt); - em_add_int_delay_sysctl(adapter, "tx_abs_int_delay", - "transmit interrupt delay limit in usecs", - &adapter->tx_abs_int_delay, - E1000_REG_OFFSET(&adapter->hw, TADV), - em_tx_abs_int_delay_dflt); - SYSCTL_ADD_PROC(&adapter->sysctl_ctx, - SYSCTL_CHILDREN(adapter->sysctl_tree), - OID_AUTO, "int_throttle_ceil", CTLTYPE_INT|CTLFLAG_RW, - adapter, 0, em_sysctl_int_throttle, "I", NULL); + /* Do Shared Code initialization */ + if (e1000_setup_init_funcs(&adapter->hw, TRUE)) { + device_printf(dev, "Setup of Shared code failed\n"); + error = ENXIO; + goto fail; } + e1000_get_bus_info(&adapter->hw); + /* - * Validate number of transmit and receive descriptors. It + * Validate number of transmit and receive descriptors. It * must not exceed hardware maximum, and must be multiple - * of EM_DBA_ALIGN. + * of E1000_DBA_ALIGN. */ - if (((em_txd * sizeof(struct em_tx_desc)) % EM_DBA_ALIGN) != 0 || - (adapter->hw.mac_type >= em_82544 && em_txd > EM_MAX_TXD) || - (adapter->hw.mac_type < em_82544 && em_txd > EM_MAX_TXD_82543) || - (em_txd < EM_MIN_TXD)) { + if ((em_txd * sizeof(struct e1000_tx_desc)) % EM_DBA_ALIGN != 0 || + (adapter->hw.mac.type >= e1000_82544 && em_txd > EM_MAX_TXD) || + (adapter->hw.mac.type < e1000_82544 && em_txd > EM_MAX_TXD_82543) || + em_txd < EM_MIN_TXD) { device_printf(dev, "Using %d TX descriptors instead of %d!\n", - EM_DEFAULT_TXD, em_txd); + EM_DEFAULT_TXD, em_txd); adapter->num_tx_desc = EM_DEFAULT_TXD; } else { adapter->num_tx_desc = em_txd; } - - if (((em_rxd * sizeof(struct em_rx_desc)) % EM_DBA_ALIGN) != 0 || - (adapter->hw.mac_type >= em_82544 && em_rxd > EM_MAX_RXD) || - (adapter->hw.mac_type < em_82544 && em_rxd > EM_MAX_RXD_82543) || - (em_rxd < EM_MIN_RXD)) { + if ((em_rxd * sizeof(struct e1000_rx_desc)) % EM_DBA_ALIGN != 0 || + (adapter->hw.mac.type >= e1000_82544 && em_rxd > EM_MAX_RXD) || + (adapter->hw.mac.type < e1000_82544 && em_rxd > EM_MAX_RXD_82543) || + em_rxd < EM_MIN_RXD) { device_printf(dev, "Using %d RX descriptors instead of %d!\n", - EM_DEFAULT_RXD, em_rxd); + EM_DEFAULT_RXD, em_rxd); adapter->num_rx_desc = EM_DEFAULT_RXD; } else { adapter->num_rx_desc = em_rxd; } - SYSCTL_ADD_INT(&adapter->sysctl_ctx, - SYSCTL_CHILDREN(adapter->sysctl_tree), OID_AUTO, "rxd", - CTLFLAG_RD, &adapter->num_rx_desc, 0, NULL); - SYSCTL_ADD_INT(&adapter->sysctl_ctx, - SYSCTL_CHILDREN(adapter->sysctl_tree), OID_AUTO, "txd", - CTLFLAG_RD, &adapter->num_tx_desc, 0, NULL); + adapter->hw.mac.autoneg = DO_AUTO_NEG; + adapter->hw.phy.autoneg_wait_to_complete = FALSE; + adapter->hw.phy.autoneg_advertised = AUTONEG_ADV_DEFAULT; + adapter->rx_buffer_len = MCLBYTES; - adapter->hw.autoneg = DO_AUTO_NEG; - adapter->hw.wait_autoneg_complete = WAIT_FOR_AUTO_NEG_DEFAULT; - adapter->hw.autoneg_advertised = AUTONEG_ADV_DEFAULT; - adapter->hw.tbi_compatibility_en = TRUE; - adapter->rx_buffer_len = EM_RXBUFFER_2048; + /* + * Interrupt throttle rate + */ + if (em_int_throttle_ceil == 0) { + adapter->int_throttle_ceil = 0; + } else { + int throttle = em_int_throttle_ceil; - adapter->hw.phy_init_script = 1; - adapter->hw.phy_reset_disable = FALSE; + if (throttle < 0) + throttle = EM_DEFAULT_ITR; -#ifndef EM_MASTER_SLAVE - adapter->hw.master_slave = em_ms_hw_default; -#else - adapter->hw.master_slave = EM_MASTER_SLAVE; -#endif + /* Recalculate the tunable value to get the exact frequency. */ + throttle = 1000000000 / 256 / throttle; + adapter->int_throttle_ceil = 1000000000 / 256 / throttle; + } - /* - * Set the max frame size assuming standard ethernet - * sized frames. - */ - adapter->hw.max_frame_size = ETHERMTU + ETHER_HDR_LEN + ETHER_CRC_LEN; + e1000_init_script_state_82541(&adapter->hw, TRUE); + e1000_set_tbi_compatibility_82543(&adapter->hw, TRUE); + + /* Copper options */ + if (adapter->hw.phy.media_type == e1000_media_type_copper) { + adapter->hw.phy.mdix = AUTO_ALL_MODES; + adapter->hw.phy.disable_polarity_correction = FALSE; + adapter->hw.phy.ms_type = EM_MASTER_SLAVE; + } + + /* Set the frame limits assuming standard ethernet sized frames. */ + adapter->max_frame_size = ETHERMTU + ETHER_HDR_LEN + ETHER_CRC_LEN; + adapter->min_frame_size = ETH_ZLEN + ETHER_CRC_LEN; - adapter->hw.min_frame_size = - MINIMUM_ETHERNET_PACKET_SIZE + ETHER_CRC_LEN; + /* This controls when hardware reports transmit completion status. */ + adapter->hw.mac.report_tx_early = 1; /* - * This controls when hardware reports transmit completion - * status. + * Create top level busdma tag */ - adapter->hw.report_tx_early = 1; - - error = em_allocate_pci_resources(dev); - if (error) + error = bus_dma_tag_create(NULL, 1, 0, + BUS_SPACE_MAXADDR, BUS_SPACE_MAXADDR, + NULL, NULL, + BUS_SPACE_MAXSIZE_32BIT, 0, BUS_SPACE_MAXSIZE_32BIT, + 0, &adapter->parent_dtag); + if (error) { + device_printf(dev, "could not create top level DMA tag\n"); goto fail; + } - /* Initialize eeprom parameters */ - em_init_eeprom_params(&adapter->hw); - - tsize = roundup2(adapter->num_tx_desc * sizeof(struct em_tx_desc), + /* + * Allocate Transmit Descriptor ring + */ + tsize = roundup2(adapter->num_tx_desc * sizeof(struct e1000_tx_desc), EM_DBA_ALIGN); - - /* Allocate Transmit Descriptor ring */ error = em_dma_malloc(adapter, tsize, &adapter->txdma); if (error) { - device_printf(dev, "Unable to allocate TxDescriptor memory\n"); + device_printf(dev, "Unable to allocate tx_desc memory\n"); goto fail; } - adapter->tx_desc_base = (struct em_tx_desc *)adapter->txdma.dma_vaddr; + adapter->tx_desc_base = adapter->txdma.dma_vaddr; - rsize = roundup2(adapter->num_rx_desc * sizeof(struct em_rx_desc), + /* + * Allocate Receive Descriptor ring + */ + rsize = roundup2(adapter->num_rx_desc * sizeof(struct e1000_rx_desc), EM_DBA_ALIGN); - - /* Allocate Receive Descriptor ring */ error = em_dma_malloc(adapter, rsize, &adapter->rxdma); if (error) { device_printf(dev, "Unable to allocate rx_desc memory\n"); goto fail; } - adapter->rx_desc_base = (struct em_rx_desc *)adapter->rxdma.dma_vaddr; + adapter->rx_desc_base = adapter->rxdma.dma_vaddr; + + /* Make sure we have a good EEPROM before we read from it */ + if (e1000_validate_nvm_checksum(&adapter->hw) < 0) { + /* + * Some PCI-E parts fail the first check due to + * the link being in sleep state, call it again, + * if it fails a second time its a real issue. + */ + if (e1000_validate_nvm_checksum(&adapter->hw) < 0) { + device_printf(dev, + "The EEPROM Checksum Is Not Valid\n"); + error = EIO; + goto fail; + } + } /* Initialize the hardware */ - if (em_hardware_init(adapter)) { + error = em_hw_init(adapter); + if (error) { device_printf(dev, "Unable to initialize the hardware\n"); - error = EIO; goto fail; } /* Copy the permanent MAC address out of the EEPROM */ - if (em_read_mac_addr(&adapter->hw) < 0) { - device_printf(dev, - "EEPROM read error while reading MAC address\n"); + if (e1000_read_mac_addr(&adapter->hw) < 0) { + device_printf(dev, "EEPROM read error while reading MAC" + " address\n"); error = EIO; goto fail; } - - if (!em_is_valid_ether_addr(adapter->hw.mac_addr)) { + if (!em_is_valid_eaddr(adapter->hw.mac.addr)) { device_printf(dev, "Invalid MAC address\n"); error = EIO; goto fail; } + /* Allocate transmit descriptors and buffers */ + error = em_create_tx_ring(adapter); + if (error) { + device_printf(dev, "Could not setup transmit structures\n"); + goto fail; + } + + /* Allocate receive descriptors and buffers */ + error = em_create_rx_ring(adapter); + if (error) { + device_printf(dev, "Could not setup receive structures\n"); + goto fail; + } + + /* Manually turn off all interrupts */ + E1000_WRITE_REG(&adapter->hw, E1000_IMC, 0xffffffff); + /* Setup OS specific network interface */ - em_setup_interface(dev, adapter); + em_setup_ifp(adapter); + + /* Add sysctl tree, must after em_setup_ifp() */ + em_add_sysctl(adapter); /* Initialize statistics */ - em_clear_hw_cntrs(&adapter->hw); - em_update_stats_counters(adapter); - adapter->hw.get_link_status = 1; + em_update_stats(adapter); + + adapter->hw.mac.get_link_status = 1; em_update_link_status(adapter); /* Indicate SOL/IDER usage */ - if (em_check_phy_reset_block(&adapter->hw)) { - device_printf(dev, "PHY reset is blocked due to " - "SOL/IDER session.\n"); - } - - /* Identify 82544 on PCIX */ - em_get_bus_info(&adapter->hw); - if (adapter->hw.bus_type == em_bus_type_pcix && - adapter->hw.mac_type == em_82544) + if (e1000_check_reset_block(&adapter->hw)) { + device_printf(dev, + "PHY reset is blocked due to SOL/IDER session.\n"); + } + + /* Determine if we have to control management hardware */ + adapter->has_manage = e1000_enable_mng_pass_thru(&adapter->hw); + + /* + * Setup Wake-on-Lan + */ + switch (adapter->hw.mac.type) { + case e1000_82542: + case e1000_82543: + break; + + case e1000_82546: + case e1000_82546_rev_3: + case e1000_82571: + case e1000_80003es2lan: + if (adapter->hw.bus.func == 1) { + e1000_read_nvm(&adapter->hw, + NVM_INIT_CONTROL3_PORT_B, 1, &eeprom_data); + } else { + e1000_read_nvm(&adapter->hw, + NVM_INIT_CONTROL3_PORT_A, 1, &eeprom_data); + } + eeprom_data &= EM_EEPROM_APME; + break; + + default: + /* APME bit in EEPROM is mapped to WUC.APME */ + eeprom_data = + E1000_READ_REG(&adapter->hw, E1000_WUC) & E1000_WUC_APME; + break; + } + if (eeprom_data) + adapter->wol = E1000_WUFC_MAG; + /* + * We have the eeprom settings, now apply the special cases + * where the eeprom may be wrong or the board won't support + * wake on lan on a particular port + */ + device_id = pci_get_device(dev); + switch (device_id) { + case E1000_DEV_ID_82546GB_PCIE: + adapter->wol = 0; + break; + + case E1000_DEV_ID_82546EB_FIBER: + case E1000_DEV_ID_82546GB_FIBER: + case E1000_DEV_ID_82571EB_FIBER: + /* + * Wake events only supported on port A for dual fiber + * regardless of eeprom setting + */ + if (E1000_READ_REG(&adapter->hw, E1000_STATUS) & + E1000_STATUS_FUNC_1) + adapter->wol = 0; + break; + + case E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3: + case E1000_DEV_ID_82571EB_QUAD_COPPER: + case E1000_DEV_ID_82571EB_QUAD_FIBER: + case E1000_DEV_ID_82571EB_QUAD_COPPER_LP: + /* if quad port adapter, disable WoL on all but port A */ + if (em_global_quad_port_a != 0) + adapter->wol = 0; + /* Reset for multiple quad port adapters */ + if (++em_global_quad_port_a == 4) + em_global_quad_port_a = 0; + break; + } + + /* XXX disable wol */ + adapter->wol = 0; + + /* Do we need workaround for 82544 PCI-X adapter? */ + if (adapter->hw.bus.type == e1000_bus_type_pcix && + adapter->hw.mac.type == e1000_82544) adapter->pcix_82544 = TRUE; else adapter->pcix_82544 = FALSE; - error = bus_setup_intr(dev, adapter->res_interrupt, INTR_MPSAFE, - em_intr, adapter, - &adapter->int_handler_tag, ifp->if_serializer); + if (adapter->pcix_82544) { + /* + * 82544 on PCI-X may split one TX segment + * into two TX descs, so we double its number + * of spare TX desc here. + */ + adapter->spare_tx_desc = 2 * EM_TX_SPARE; + } else { + adapter->spare_tx_desc = EM_TX_SPARE; + } + + error = bus_setup_intr(dev, adapter->intr_res, INTR_MPSAFE, + em_intr, adapter, &adapter->intr_tag, + ifp->if_serializer); if (error) { - device_printf(dev, "Error registering interrupt handler!\n"); - ether_ifdetach(ifp); + device_printf(dev, "Failed to register interrupt handler"); + ether_ifdetach(&adapter->arpcom.ac_if); goto fail; } - ifp->if_cpuid = ithread_cpuid(rman_get_start(adapter->res_interrupt)); + ifp->if_cpuid = ithread_cpuid(rman_get_start(adapter->intr_res)); KKASSERT(ifp->if_cpuid >= 0 && ifp->if_cpuid < ncpus); - INIT_DEBUGOUT("em_attach: end"); - return(0); - + return (0); fail: em_detach(dev); - return(error); + return (error); } -/********************************************************************* - * Device removal routine - * - * The detach entry point is called when the driver is being removed. - * This routine stops the adapter and deallocates all the resources - * that were allocated for driver operation. - * - * return 0 on success, positive on failure - *********************************************************************/ - static int em_detach(device_t dev) { struct adapter *adapter = device_get_softc(dev); - INIT_DEBUGOUT("em_detach: begin"); - if (device_is_attached(dev)) { - struct ifnet *ifp = &adapter->interface_data.ac_if; + struct ifnet *ifp = &adapter->arpcom.ac_if; lwkt_serialize_enter(ifp->if_serializer); + adapter->in_detach = 1; em_stop(adapter); - em_phy_hw_reset(&adapter->hw); - bus_teardown_intr(dev, adapter->res_interrupt, - adapter->int_handler_tag); + + e1000_phy_hw_reset(&adapter->hw); + + em_rel_mgmt(adapter); + + if ((adapter->hw.mac.type == e1000_82573 || + adapter->hw.mac.type == e1000_ich8lan || + adapter->hw.mac.type == e1000_ich10lan || + adapter->hw.mac.type == e1000_ich9lan) && + e1000_check_mng_mode(&adapter->hw)) + em_rel_hw_control(adapter); + + if (adapter->wol) { + E1000_WRITE_REG(&adapter->hw, E1000_WUC, + E1000_WUC_PME_EN); + E1000_WRITE_REG(&adapter->hw, E1000_WUFC, adapter->wol); + em_enable_wol(dev); + } + + bus_teardown_intr(dev, adapter->intr_res, adapter->intr_tag); + lwkt_serialize_exit(ifp->if_serializer); ether_ifdetach(ifp); } bus_generic_detach(dev); - em_free_pci_resources(dev); + em_free_pci_res(adapter); + + em_destroy_tx_ring(adapter, adapter->num_tx_desc); + em_destroy_rx_ring(adapter, adapter->num_rx_desc); /* Free Transmit Descriptor ring */ - if (adapter->tx_desc_base != NULL) { + if (adapter->tx_desc_base) em_dma_free(adapter, &adapter->txdma); - adapter->tx_desc_base = NULL; - } /* Free Receive Descriptor ring */ - if (adapter->rx_desc_base != NULL) { + if (adapter->rx_desc_base) em_dma_free(adapter, &adapter->rxdma); - adapter->rx_desc_base = NULL; - } + + /* Free top level busdma tag */ + if (adapter->parent_dtag != NULL) + bus_dma_tag_destroy(adapter->parent_dtag); /* Free sysctl tree */ - if (adapter->sysctl_tree != NULL) { - adapter->sysctl_tree = NULL; + if (adapter->sysctl_tree != NULL) sysctl_ctx_free(&adapter->sysctl_ctx); - } return (0); } -/********************************************************************* - * - * Shutdown entry point - * - **********************************************************************/ - static int em_shutdown(device_t dev) { - struct adapter *adapter = device_get_softc(dev); - struct ifnet *ifp = &adapter->interface_data.ac_if; - - lwkt_serialize_enter(ifp->if_serializer); - em_stop(adapter); - lwkt_serialize_exit(ifp->if_serializer); - - return (0); + return em_suspend(dev); } -/* - * Suspend/resume device methods. - */ static int em_suspend(device_t dev) { struct adapter *adapter = device_get_softc(dev); - struct ifnet *ifp = &adapter->interface_data.ac_if; + struct ifnet *ifp = &adapter->arpcom.ac_if; lwkt_serialize_enter(ifp->if_serializer); + em_stop(adapter); + + em_rel_mgmt(adapter); + + if ((adapter->hw.mac.type == e1000_82573 || + adapter->hw.mac.type == e1000_ich8lan || + adapter->hw.mac.type == e1000_ich10lan || + adapter->hw.mac.type == e1000_ich9lan) && + e1000_check_mng_mode(&adapter->hw)) + em_rel_hw_control(adapter); + + if (adapter->wol) { + E1000_WRITE_REG(&adapter->hw, E1000_WUC, E1000_WUC_PME_EN); + E1000_WRITE_REG(&adapter->hw, E1000_WUFC, adapter->wol); + em_enable_wol(dev); + } + lwkt_serialize_exit(ifp->if_serializer); - return (0); + + return bus_generic_suspend(dev); } static int em_resume(device_t dev) { struct adapter *adapter = device_get_softc(dev); - struct ifnet *ifp = &adapter->interface_data.ac_if; + struct ifnet *ifp = &adapter->arpcom.ac_if; lwkt_serialize_enter(ifp->if_serializer); - ifp->if_flags &= ~IFF_RUNNING; + em_init(adapter); + em_get_mgmt(adapter); if_devstart(ifp); + lwkt_serialize_exit(ifp->if_serializer); return bus_generic_resume(dev); } -/********************************************************************* - * Transmit entry point - * - * em_start is called by the stack to initiate a transmit. - * The driver will remain in this routine as long as there are - * packets to transmit and transmit resources are available. - * In case resources are not available stack is notified and - * the packet is requeued. - **********************************************************************/ - static void em_start(struct ifnet *ifp) { - struct mbuf *m_head; struct adapter *adapter = ifp->if_softc; + struct mbuf *m_head; ASSERT_SERIALIZED(ifp->if_serializer); if ((ifp->if_flags & (IFF_RUNNING | IFF_OACTIVE)) != IFF_RUNNING) return; + if (!adapter->link_active) { ifq_purge(&ifp->if_snd); return; } + while (!ifq_is_empty(&ifp->if_snd)) { + /* + * Force a cleanup if number of TX descriptors + * available hits the threshold + */ + if (adapter->num_tx_desc_avail <= EM_TX_CLEANUP_THRESHOLD) { + em_txeof(adapter); + + /* Now do we at least have a minimal? */ + if (EM_IS_OACTIVE(adapter)) { + adapter->no_tx_desc_avail1++; + ifp->if_flags |= IFF_OACTIVE; + break; + } + } + + logif(pkt_txqueue); m_head = ifq_dequeue(&ifp->if_snd, NULL); if (m_head == NULL) break; - logif(pkt_txqueue); - if (em_encap(adapter, m_head)) { - ifp->if_flags |= IFF_OACTIVE; - ifq_prepend(&ifp->if_snd, m_head); - break; + if (em_encap(adapter, &m_head)) { + if (adapter->num_tx_desc_avail == + adapter->num_tx_desc) { + continue; + } else { + ifp->if_flags |= IFF_OACTIVE; + break; + } } /* Send a copy of the frame to the BPF listener */ @@ -845,194 +929,184 @@ em_start(struct ifnet *ifp) } } -/********************************************************************* - * Ioctl entry point - * - * em_ioctl is called when the user wants to configure the - * interface. - * - * return 0 on success, positive on failure - **********************************************************************/ - static int em_ioctl(struct ifnet *ifp, u_long command, caddr_t data, struct ucred *cr) { - int max_frame_size, mask, error = 0, reinit = 0; - struct ifreq *ifr = (struct ifreq *) data; struct adapter *adapter = ifp->if_softc; + struct ifreq *ifr = (struct ifreq *)data; uint16_t eeprom_data = 0; - - ASSERT_SERIALIZED(ifp->if_serializer); + int max_frame_size, mask, reinit; + int error = 0; if (adapter->in_detach) - return 0; + return (error); + + ASSERT_SERIALIZED(ifp->if_serializer); switch (command) { case SIOCSIFMTU: - IOCTL_DEBUGOUT("ioctl rcv'd: SIOCSIFMTU (Set Interface MTU)"); - switch (adapter->hw.mac_type) { - case em_82573: + switch (adapter->hw.mac.type) { + case e1000_82573: /* * 82573 only supports jumbo frames * if ASPM is disabled. */ - em_read_eeprom(&adapter->hw, EEPROM_INIT_3GIO_3, - 1, &eeprom_data); - if (eeprom_data & EEPROM_WORD1A_ASPM_MASK) { + e1000_read_nvm(&adapter->hw, + NVM_INIT_3GIO_3, 1, &eeprom_data); + if (eeprom_data & NVM_WORD1A_ASPM_MASK) { max_frame_size = ETHER_MAX_LEN; break; } - /* Allow Jumbo frames */ - /* FALLTHROUGH */ - case em_82571: - case em_82572: - case em_ich9lan: - case em_80003es2lan: /* Limit Jumbo Frame size */ + /* FALL THROUGH */ + + /* Limit Jumbo Frame size */ + case e1000_82571: + case e1000_82572: + case e1000_ich9lan: + case e1000_ich10lan: + case e1000_82574: + case e1000_80003es2lan: max_frame_size = 9234; break; - case em_ich8lan: - /* ICH8 does not support jumbo frames */ + + /* Adapters that do not support jumbo frames */ + case e1000_82542: + case e1000_ich8lan: max_frame_size = ETHER_MAX_LEN; break; + default: max_frame_size = MAX_JUMBO_FRAME_SIZE; break; } - if (ifr->ifr_mtu > - max_frame_size - ETHER_HDR_LEN - ETHER_CRC_LEN) { + if (ifr->ifr_mtu > max_frame_size - ETHER_HDR_LEN - + ETHER_CRC_LEN) { error = EINVAL; - } else { - ifp->if_mtu = ifr->ifr_mtu; - adapter->hw.max_frame_size = - ifp->if_mtu + ETHER_HDR_LEN + ETHER_CRC_LEN; - ifp->if_flags &= ~IFF_RUNNING; - em_init(adapter); + break; } + + ifp->if_mtu = ifr->ifr_mtu; + adapter->max_frame_size = + ifp->if_mtu + ETHER_HDR_LEN + ETHER_CRC_LEN; + + if (ifp->if_flags & IFF_RUNNING) + em_init(adapter); break; + case SIOCSIFFLAGS: - IOCTL_DEBUGOUT("ioctl rcv'd: SIOCSIFFLAGS " - "(Set Interface Flags)"); if (ifp->if_flags & IFF_UP) { - if (!(ifp->if_flags & IFF_RUNNING)) { + if ((ifp->if_flags & IFF_RUNNING)) { + if ((ifp->if_flags ^ adapter->if_flags) & + (IFF_PROMISC | IFF_ALLMULTI)) { + em_disable_promisc(adapter); + em_set_promisc(adapter); + } + } else { em_init(adapter); - } else if ((ifp->if_flags ^ adapter->if_flags) & - (IFF_PROMISC | IFF_ALLMULTI)) { - em_disable_promisc(adapter); - em_set_promisc(adapter); } - } else { - if (ifp->if_flags & IFF_RUNNING) - em_stop(adapter); + } else if (ifp->if_flags & IFF_RUNNING) { + em_stop(adapter); } adapter->if_flags = ifp->if_flags; break; + case SIOCADDMULTI: case SIOCDELMULTI: - IOCTL_DEBUGOUT("ioctl rcv'd: SIOC(ADD|DEL)MULTI"); if (ifp->if_flags & IFF_RUNNING) { em_disable_intr(adapter); em_set_multi(adapter); - if (adapter->hw.mac_type == em_82542_rev2_0) - em_initialize_receive_unit(adapter); + if (adapter->hw.mac.type == e1000_82542 && + adapter->hw.revision_id == E1000_REVISION_2) + em_init_rx_unit(adapter); #ifdef DEVICE_POLLING - /* Do not enable interrupt if polling(4) is enabled */ - if ((ifp->if_flags & IFF_POLLING) == 0) + if (!(ifp->if_flags & IFF_POLLING)) #endif - em_enable_intr(adapter); + em_enable_intr(adapter); } break; + case SIOCSIFMEDIA: /* Check SOL/IDER usage */ - if (em_check_phy_reset_block(&adapter->hw)) { - if_printf(ifp, "Media change is blocked due to " - "SOL/IDER session.\n"); + if (e1000_check_reset_block(&adapter->hw)) { + device_printf(adapter->dev, "Media change is" + " blocked due to SOL/IDER session.\n"); break; } - /* FALLTHROUGH */ + /* FALL THROUGH */ + case SIOCGIFMEDIA: - IOCTL_DEBUGOUT("ioctl rcv'd: SIOCxIFMEDIA " - "(Get/Set Interface Media)"); error = ifmedia_ioctl(ifp, ifr, &adapter->media, command); break; + case SIOCSIFCAP: - IOCTL_DEBUGOUT("ioctl rcv'd: SIOCSIFCAP (Set Capabilities)"); + reinit = 0; mask = ifr->ifr_reqcap ^ ifp->if_capenable; if (mask & IFCAP_HWCSUM) { - ifp->if_capenable ^= IFCAP_HWCSUM; + ifp->if_capenable ^= (mask & IFCAP_HWCSUM); reinit = 1; } if (mask & IFCAP_VLAN_HWTAGGING) { ifp->if_capenable ^= IFCAP_VLAN_HWTAGGING; reinit = 1; } - if (reinit && (ifp->if_flags & IFF_RUNNING)) { - ifp->if_flags &= ~IFF_RUNNING; + if (reinit && (ifp->if_flags & IFF_RUNNING)) em_init(adapter); - } break; + default: error = ether_ioctl(ifp, command, data); break; } - return (error); } -/********************************************************************* - * Watchdog entry point - * - * This routine is called whenever hardware quits transmitting. - * - **********************************************************************/ - static void em_watchdog(struct ifnet *ifp) { struct adapter *adapter = ifp->if_softc; + ASSERT_SERIALIZED(ifp->if_serializer); + + /* + * The timer is set to 5 every time start queues a packet. + * Then txeof keeps resetting it as long as it cleans at + * least one descriptor. + * Finally, anytime all descriptors are clean the timer is + * set to 0. + */ + /* * If we are in this routine because of pause frames, then * don't reset the hardware. */ - if (E1000_READ_REG(&adapter->hw, STATUS) & E1000_STATUS_TXOFF) { + if (E1000_READ_REG(&adapter->hw, E1000_STATUS) & + E1000_STATUS_TXOFF) { ifp->if_timer = EM_TX_TIMEOUT; return; } - if (em_check_for_link(&adapter->hw) == 0) + if (e1000_check_for_link(&adapter->hw) == 0) if_printf(ifp, "watchdog timeout -- resetting\n"); - ifp->if_flags &= ~IFF_RUNNING; + ifp->if_oerrors++; + adapter->watchdog_events++; + em_init(adapter); - adapter->watchdog_timeouts++; + if (!ifq_is_empty(&ifp->if_snd)) + if_devstart(ifp); } -/********************************************************************* - * Init entry point - * - * This routine is used in two ways. It is used by the stack as - * init entry point in network interface structure. It is also used - * by the driver as a hw/sw initialization routine to get to a - * consistent state. - * - * return 0 on success, positive on failure - **********************************************************************/ - static void -em_init(void *arg) +em_init(void *xsc) { - struct adapter *adapter = arg; + struct adapter *adapter = xsc; + struct ifnet *ifp = &adapter->arpcom.ac_if; + device_t dev = adapter->dev; uint32_t pba; - struct ifnet *ifp = &adapter->interface_data.ac_if; ASSERT_SERIALIZED(ifp->if_serializer); - INIT_DEBUGOUT("em_init: begin"); - - if (ifp->if_flags & IFF_RUNNING) - return; - em_stop(adapter); /* @@ -1046,86 +1120,114 @@ em_init(void *arg) * Default allocation: PBA=30K for Rx, leaving 10K for Tx. * Note: default does not leave enough room for Jumbo Frame >10k. */ - switch (adapter->hw.mac_type) { - case em_82547: - case em_82547_rev_2: /* 82547: Total Packet Buffer is 40K */ - if (adapter->hw.max_frame_size > EM_RXBUFFER_8192) + switch (adapter->hw.mac.type) { + case e1000_82547: + case e1000_82547_rev_2: /* 82547: Total Packet Buffer is 40K */ + if (adapter->max_frame_size > 8192) pba = E1000_PBA_22K; /* 22K for Rx, 18K for Tx */ else pba = E1000_PBA_30K; /* 30K for Rx, 10K for Tx */ - adapter->tx_fifo_head = 0; adapter->tx_head_addr = pba << EM_TX_HEAD_ADDR_SHIFT; adapter->tx_fifo_size = - (E1000_PBA_40K - pba) << EM_PBA_BYTES_SHIFT; + (E1000_PBA_40K - pba) << EM_PBA_BYTES_SHIFT; break; + /* Total Packet Buffer on these is 48K */ - case em_82571: - case em_82572: - case em_80003es2lan: + case e1000_82571: + case e1000_82572: + case e1000_80003es2lan: pba = E1000_PBA_32K; /* 32K for Rx, 16K for Tx */ break; - case em_82573: /* 82573: Total Packet Buffer is 32K */ + + case e1000_82573: /* 82573: Total Packet Buffer is 32K */ pba = E1000_PBA_12K; /* 12K for Rx, 20K for Tx */ break; - case em_ich8lan: - pba = E1000_PBA_8K; + + case e1000_82574: + pba = E1000_PBA_20K; /* 20K for Rx, 20K for Tx */ break; - case em_ich9lan: -#define E1000_PBA_10K 0x000A + + case e1000_ich9lan: + case e1000_ich10lan: +#define E1000_PBA_10K 0x000A pba = E1000_PBA_10K; break; + + case e1000_ich8lan: + pba = E1000_PBA_8K; + break; + default: /* Devices before 82547 had a Packet Buffer of 64K. */ - if(adapter->hw.max_frame_size > EM_RXBUFFER_8192) + if (adapter->max_frame_size > 8192) pba = E1000_PBA_40K; /* 40K for Rx, 24K for Tx */ else pba = E1000_PBA_48K; /* 48K for Rx, 16K for Tx */ } - INIT_DEBUGOUT1("em_init: pba=%dK",pba); - E1000_WRITE_REG(&adapter->hw, PBA, pba); - + E1000_WRITE_REG(&adapter->hw, E1000_PBA, pba); + /* Get the latest mac address, User can use a LAA */ - bcopy(adapter->interface_data.ac_enaddr, adapter->hw.mac_addr, - ETHER_ADDR_LEN); + bcopy(IF_LLADDR(ifp), adapter->hw.mac.addr, ETHER_ADDR_LEN); + + /* Put the address into the Receive Address Array */ + e1000_rar_set(&adapter->hw, adapter->hw.mac.addr, 0); + + /* + * With the 82571 adapter, RAR[0] may be overwritten + * when the other port is reset, we make a duplicate + * in RAR[14] for that eventuality, this assures + * the interface continues to function. + */ + if (adapter->hw.mac.type == e1000_82571) { + e1000_set_laa_state_82571(&adapter->hw, TRUE); + e1000_rar_set(&adapter->hw, adapter->hw.mac.addr, + E1000_RAR_ENTRIES - 1); + } /* Initialize the hardware */ - if (em_hardware_init(adapter)) { - if_printf(ifp, "Unable to initialize the hardware\n"); + if (em_hw_init(adapter)) { + device_printf(dev, "Unable to initialize the hardware\n"); + /* XXX em_stop()? */ return; } em_update_link_status(adapter); - if (ifp->if_capenable & IFCAP_VLAN_HWTAGGING) - em_enable_vlans(adapter); + /* Setup VLAN support, basic and offload if available */ + E1000_WRITE_REG(&adapter->hw, E1000_VET, ETHERTYPE_VLAN); - /* Set hardware offload abilities */ - if (adapter->hw.mac_type >= em_82543) { - if (ifp->if_capenable & IFCAP_TXCSUM) - ifp->if_hwassist = EM_CHECKSUM_FEATURES; - else - ifp->if_hwassist = 0; + if (ifp->if_capenable & IFCAP_VLAN_HWTAGGING) { + uint32_t ctrl; + + ctrl = E1000_READ_REG(&adapter->hw, E1000_CTRL); + ctrl |= E1000_CTRL_VME; + E1000_WRITE_REG(&adapter->hw, E1000_CTRL, ctrl); } + /* Set hardware offload abilities */ + if (ifp->if_capenable & IFCAP_TXCSUM) + ifp->if_hwassist = EM_CSUM_FEATURES; + else + ifp->if_hwassist = 0; + + /* Configure for OS presence */ + em_get_mgmt(adapter); + /* Prepare transmit descriptors and buffers */ - if (em_setup_transmit_structures(adapter)) { - if_printf(ifp, "Could not setup transmit structures\n"); - em_stop(adapter); - return; - } - em_initialize_transmit_unit(adapter); + em_init_tx_ring(adapter); + em_init_tx_unit(adapter); /* Setup Multicast table */ em_set_multi(adapter); /* Prepare receive descriptors and buffers */ - if (em_setup_receive_structures(adapter)) { - if_printf(ifp, "Could not setup receive structures\n"); + if (em_init_rx_ring(adapter)) { + device_printf(dev, "Could not setup receive structures\n"); em_stop(adapter); return; } - em_initialize_receive_unit(adapter); + em_init_rx_unit(adapter); /* Don't lose promiscuous settings */ em_set_promisc(adapter); @@ -1133,19 +1235,39 @@ em_init(void *arg) ifp->if_flags |= IFF_RUNNING; ifp->if_flags &= ~IFF_OACTIVE; - callout_reset(&adapter->timer, hz, em_local_timer, adapter); - em_clear_hw_cntrs(&adapter->hw); + callout_reset(&adapter->timer, hz, em_timer, adapter); + e1000_clear_hw_cntrs_base_generic(&adapter->hw); + + /* MSI/X configuration for 82574 */ + if (adapter->hw.mac.type == e1000_82574) { + int tmp; + + tmp = E1000_READ_REG(&adapter->hw, E1000_CTRL_EXT); + tmp |= E1000_CTRL_EXT_PBA_CLR; + E1000_WRITE_REG(&adapter->hw, E1000_CTRL_EXT, tmp); + /* + * Set the IVAR - interrupt vector routing. + * Each nibble represents a vector, high bit + * is enable, other 3 bits are the MSIX table + * entry, we map RXQ0 to 0, TXQ0 to 1, and + * Link (other) to 2, hence the magic number. + */ + E1000_WRITE_REG(&adapter->hw, E1000_IVAR, 0x800A0908); + } #ifdef DEVICE_POLLING - /* Do not enable interrupt if polling(4) is enabled */ + /* + * Only enable interrupts if we are not polling, make sure + * they are off otherwise. + */ if (ifp->if_flags & IFF_POLLING) em_disable_intr(adapter); else -#endif - em_enable_intr(adapter); +#endif /* DEVICE_POLLING */ + em_enable_intr(adapter); /* Don't reset the phy next time init gets called */ - adapter->hw.phy_reset_disable = TRUE; + adapter->hw.phy.reset_disable = TRUE; } #ifdef DEVICE_POLLING @@ -1158,24 +1280,24 @@ em_poll(struct ifnet *ifp, enum poll_cmd cmd, int count) ASSERT_SERIALIZED(ifp->if_serializer); - switch(cmd) { + switch (cmd) { case POLL_REGISTER: em_disable_intr(adapter); break; + case POLL_DEREGISTER: em_enable_intr(adapter); break; + case POLL_AND_CHECK_STATUS: - reg_icr = E1000_READ_REG(&adapter->hw, ICR); + reg_icr = E1000_READ_REG(&adapter->hw, E1000_ICR); if (reg_icr & (E1000_ICR_RXSEQ | E1000_ICR_LSC)) { callout_stop(&adapter->timer); - adapter->hw.get_link_status = 1; - em_check_for_link(&adapter->hw); + adapter->hw.mac.get_link_status = 1; em_update_link_status(adapter); - callout_reset(&adapter->timer, hz, em_local_timer, - adapter); + callout_reset(&adapter->timer, hz, em_timer, adapter); } - /* fall through */ + /* FALL THROUGH */ case POLL_ONLY: if (ifp->if_flags & IFF_RUNNING) { em_rxeof(adapter, count); @@ -1190,25 +1312,19 @@ em_poll(struct ifnet *ifp, enum poll_cmd cmd, int count) #endif /* DEVICE_POLLING */ -/********************************************************************* - * - * Interrupt Service routine - * - *********************************************************************/ static void -em_intr(void *arg) +em_intr(void *xsc) { + struct adapter *adapter = xsc; + struct ifnet *ifp = &adapter->arpcom.ac_if; uint32_t reg_icr; - struct ifnet *ifp; - struct adapter *adapter = arg; - - ifp = &adapter->interface_data.ac_if; logif(intr_beg); ASSERT_SERIALIZED(ifp->if_serializer); - reg_icr = E1000_READ_REG(&adapter->hw, ICR); - if ((adapter->hw.mac_type >= em_82571 && + reg_icr = E1000_READ_REG(&adapter->hw, E1000_ICR); + + if ((adapter->hw.mac.type >= e1000_82571 && (reg_icr & E1000_ICR_INT_ASSERTED) == 0) || reg_icr == 0) { logif(intr_end); @@ -1216,21 +1332,16 @@ em_intr(void *arg) } /* - * XXX: some laptops trigger several spurious interrupts on em(4) - * when in the resume cycle. The ICR register reports all-ones - * value in this case. Processing such interrupts would lead to - * a freeze. I don't know why. + * XXX: some laptops trigger several spurious interrupts + * on em(4) when in the resume cycle. The ICR register + * reports all-ones value in this case. Processing such + * interrupts would lead to a freeze. I don't know why. */ if (reg_icr == 0xffffffff) { logif(intr_end); return; } - /* - * note: do not attempt to improve efficiency by looping. This - * only results in unnecessary piecemeal collection of received - * packets and unnecessary piecemeal cleanups of the transmit ring. - */ if (ifp->if_flags & IFF_RUNNING) { em_rxeof(adapter, -1); em_txeof(adapter); @@ -1239,10 +1350,13 @@ em_intr(void *arg) /* Link status change */ if (reg_icr & (E1000_ICR_RXSEQ | E1000_ICR_LSC)) { callout_stop(&adapter->timer); - adapter->hw.get_link_status = 1; - em_check_for_link(&adapter->hw); + adapter->hw.mac.get_link_status = 1; em_update_link_status(adapter); - callout_reset(&adapter->timer, hz, em_local_timer, adapter); + + /* Deal with TX cruft when link lost */ + em_tx_purge(adapter); + + callout_reset(&adapter->timer, hz, em_timer, adapter); } if (reg_icr & E1000_ICR_RXO) @@ -1254,25 +1368,14 @@ em_intr(void *arg) logif(intr_end); } -/********************************************************************* - * - * Media Ioctl callback - * - * This routine is called whenever the user queries the status of - * the interface using ifconfig. - * - **********************************************************************/ static void em_media_status(struct ifnet *ifp, struct ifmediareq *ifmr) { struct adapter *adapter = ifp->if_softc; u_char fiber_type = IFM_1000_SX; - INIT_DEBUGOUT("em_media_status: begin"); - ASSERT_SERIALIZED(ifp->if_serializer); - em_check_for_link(&adapter->hw); em_update_link_status(adapter); ifmr->ifm_status = IFM_AVALID; @@ -1283,9 +1386,9 @@ em_media_status(struct ifnet *ifp, struct ifmediareq *ifmr) ifmr->ifm_status |= IFM_ACTIVE; - if (adapter->hw.media_type == em_media_type_fiber || - adapter->hw.media_type == em_media_type_internal_serdes) { - if (adapter->hw.mac_type == em_82545) + if (adapter->hw.phy.media_type == e1000_media_type_fiber || + adapter->hw.phy.media_type == e1000_media_type_internal_serdes) { + if (adapter->hw.mac.type == e1000_82545) fiber_type = IFM_1000_LX; ifmr->ifm_active |= fiber_type | IFM_FDX; } else { @@ -1296,6 +1399,7 @@ em_media_status(struct ifnet *ifp, struct ifmediareq *ifmr) case 100: ifmr->ifm_active |= IFM_100_TX; break; + case 1000: ifmr->ifm_active |= IFM_1000_T; break; @@ -1307,22 +1411,12 @@ em_media_status(struct ifnet *ifp, struct ifmediareq *ifmr) } } -/********************************************************************* - * - * Media Ioctl callback - * - * This routine is called when the user changes speed/duplex using - * media/mediopt option with ifconfig. - * - **********************************************************************/ static int em_media_change(struct ifnet *ifp) { struct adapter *adapter = ifp->if_softc; struct ifmedia *ifm = &adapter->media; - INIT_DEBUGOUT("em_media_change: begin"); - ASSERT_SERIALIZED(ifp->if_serializer); if (IFM_TYPE(ifm->ifm_media) != IFM_ETHER) @@ -1330,152 +1424,132 @@ em_media_change(struct ifnet *ifp) switch (IFM_SUBTYPE(ifm->ifm_media)) { case IFM_AUTO: - adapter->hw.autoneg = DO_AUTO_NEG; - adapter->hw.autoneg_advertised = AUTONEG_ADV_DEFAULT; + adapter->hw.mac.autoneg = DO_AUTO_NEG; + adapter->hw.phy.autoneg_advertised = AUTONEG_ADV_DEFAULT; break; + case IFM_1000_LX: case IFM_1000_SX: case IFM_1000_T: - adapter->hw.autoneg = DO_AUTO_NEG; - adapter->hw.autoneg_advertised = ADVERTISE_1000_FULL; + adapter->hw.mac.autoneg = DO_AUTO_NEG; + adapter->hw.phy.autoneg_advertised = ADVERTISE_1000_FULL; break; + case IFM_100_TX: - adapter->hw.autoneg = FALSE; - adapter->hw.autoneg_advertised = 0; + adapter->hw.mac.autoneg = FALSE; + adapter->hw.phy.autoneg_advertised = 0; if ((ifm->ifm_media & IFM_GMASK) == IFM_FDX) - adapter->hw.forced_speed_duplex = em_100_full; + adapter->hw.mac.forced_speed_duplex = ADVERTISE_100_FULL; else - adapter->hw.forced_speed_duplex = em_100_half; + adapter->hw.mac.forced_speed_duplex = ADVERTISE_100_HALF; break; + case IFM_10_T: - adapter->hw.autoneg = FALSE; - adapter->hw.autoneg_advertised = 0; + adapter->hw.mac.autoneg = FALSE; + adapter->hw.phy.autoneg_advertised = 0; if ((ifm->ifm_media & IFM_GMASK) == IFM_FDX) - adapter->hw.forced_speed_duplex = em_10_full; + adapter->hw.mac.forced_speed_duplex = ADVERTISE_10_FULL; else - adapter->hw.forced_speed_duplex = em_10_half; + adapter->hw.mac.forced_speed_duplex = ADVERTISE_10_HALF; break; + default: if_printf(ifp, "Unsupported media type\n"); + break; } + /* - * As the speed/duplex settings may have changed we need to + * As the speed/duplex settings my have changed we need to * reset the PHY. */ - adapter->hw.phy_reset_disable = FALSE; + adapter->hw.phy.reset_disable = FALSE; - ifp->if_flags &= ~IFF_RUNNING; em_init(adapter); - return(0); -} - -static void -em_tx_cb(void *arg, bus_dma_segment_t *seg, int nsegs, bus_size_t mapsize, - int error) -{ - struct em_q *q = arg; - - if (error) - return; - KASSERT(nsegs <= EM_MAX_SCATTER, - ("Too many DMA segments returned when mapping tx packet")); - q->nsegs = nsegs; - bcopy(seg, q->segs, nsegs * sizeof(seg[0])); + return (0); } -/********************************************************************* - * - * This routine maps the mbufs to tx descriptors. - * - * return 0 on success, positive on failure - **********************************************************************/ static int -em_encap(struct adapter *adapter, struct mbuf *m_head) +em_encap(struct adapter *adapter, struct mbuf **m_headp) { - uint32_t txd_upper = 0, txd_lower = 0, txd_used = 0, txd_saved = 0; - int i, j, error, last = 0; - - struct em_q q; - struct em_buffer *tx_buffer = NULL, *tx_buffer_first; + bus_dma_segment_t segs[EM_MAX_SCATTER]; bus_dmamap_t map; - struct em_tx_desc *current_tx_desc = NULL; - struct ifnet *ifp = &adapter->interface_data.ac_if; + struct em_buffer *tx_buffer, *tx_buffer_mapped; + struct e1000_tx_desc *ctxd = NULL; + struct mbuf *m_head; + uint32_t txd_upper, txd_lower, txd_used; + int maxsegs, nsegs, i, j, first, last = 0, error; - /* - * Force a cleanup if number of TX descriptors - * available hits the threshold - */ - if (adapter->num_tx_desc_avail <= EM_TX_CLEANUP_THRESHOLD) { - em_txeof(adapter); - if (adapter->num_tx_desc_avail <= EM_TX_CLEANUP_THRESHOLD) { - adapter->no_tx_desc_avail1++; - return (ENOBUFS); - } - } + txd_upper = txd_lower = 0; + txd_used = 0; /* - * Capture the first descriptor index, this descriptor will have - * the index of the EOP which is the only one that now gets a - * DONE bit writeback. + * Capture the first descriptor index, this descriptor + * will have the index of the EOP which is the only one + * that now gets a DONE bit writeback. */ - tx_buffer_first = &adapter->tx_buffer_area[adapter->next_avail_tx_desc]; + first = adapter->next_avail_tx_desc; + tx_buffer = &adapter->tx_buffer_area[first]; + tx_buffer_mapped = tx_buffer; + map = tx_buffer->map; - /* - * Map the packet for DMA. - */ - map = tx_buffer_first->map; - error = bus_dmamap_load_mbuf(adapter->txtag, map, m_head, em_tx_cb, - &q, BUS_DMA_NOWAIT); - if (error != 0) { - adapter->no_tx_dma_setup++; - return (error); + maxsegs = adapter->num_tx_desc_avail - EM_TX_RESERVED; + KASSERT(maxsegs >= adapter->spare_tx_desc, + ("not enough spare TX desc\n")); + if (adapter->pcix_82544) { + /* Half it; see the comment in em_attach() */ + maxsegs >>= 1; } - KASSERT(q.nsegs != 0, ("em_encap: empty packet")); + if (maxsegs > EM_MAX_SCATTER) + maxsegs = EM_MAX_SCATTER; - if (q.nsegs > (adapter->num_tx_desc_avail - 2)) { - adapter->no_tx_desc_avail2++; - error = ENOBUFS; - goto fail; - } + error = bus_dmamap_load_mbuf_defrag(adapter->txtag, map, m_headp, + segs, maxsegs, &nsegs, BUS_DMA_NOWAIT); + if (error) { + if (error == ENOBUFS) + adapter->mbuf_alloc_failed++; + else + adapter->no_tx_dma_setup++; - if (ifp->if_hwassist > 0) { - em_transmit_checksum_setup(adapter, m_head, - &txd_upper, &txd_lower); + m_freem(*m_headp); + *m_headp = NULL; + return error; } + bus_dmamap_sync(adapter->txtag, map, BUS_DMASYNC_PREWRITE); + m_head = *m_headp; + + if (m_head->m_pkthdr.csum_flags & CSUM_OFFLOAD) { + /* TX csum offloading will consume one TX desc */ + em_txcsum(adapter, m_head, &txd_upper, &txd_lower); + } i = adapter->next_avail_tx_desc; - if (adapter->pcix_82544) - txd_saved = i; /* Set up our transmit descriptors */ - for (j = 0; j < q.nsegs; j++) { + for (j = 0; j < nsegs; j++) { /* If adapter is 82544 and on PCIX bus */ if(adapter->pcix_82544) { DESC_ARRAY desc_array; uint32_t array_elements, counter; - /* + /* * Check the Address and Length combination and * split the data accordingly */ - array_elements = em_fill_descriptors(q.segs[j].ds_addr, - q.segs[j].ds_len, &desc_array); + array_elements = em_82544_fill_desc(segs[j].ds_addr, + segs[j].ds_len, &desc_array); for (counter = 0; counter < array_elements; counter++) { - if (txd_used == adapter->num_tx_desc_avail) { - adapter->next_avail_tx_desc = txd_saved; - adapter->no_tx_desc_avail2++; - error = ENOBUFS; - goto fail; - } + KKASSERT(txd_used < adapter->num_tx_desc_avail); + tx_buffer = &adapter->tx_buffer_area[i]; - current_tx_desc = &adapter->tx_desc_base[i]; - current_tx_desc->buffer_addr = htole64( - desc_array.descriptor[counter].address); - current_tx_desc->lower.data = htole32( - adapter->txd_cmd | txd_lower | - (uint16_t)desc_array.descriptor[counter].length); - current_tx_desc->upper.data = htole32(txd_upper); + ctxd = &adapter->tx_desc_base[i]; + + ctxd->buffer_addr = htole64( + desc_array.descriptor[counter].address); + ctxd->lower.data = htole32( + adapter->txd_cmd | txd_lower | + desc_array.descriptor[counter].length); + ctxd->upper.data = htole32(txd_upper); last = i; if (++i == adapter->num_tx_desc) @@ -1484,15 +1558,15 @@ em_encap(struct adapter *adapter, struct mbuf *m_head) tx_buffer->m_head = NULL; tx_buffer->next_eop = -1; txd_used++; - } + } } else { tx_buffer = &adapter->tx_buffer_area[i]; - current_tx_desc = &adapter->tx_desc_base[i]; + ctxd = &adapter->tx_desc_base[i]; - current_tx_desc->buffer_addr = htole64(q.segs[j].ds_addr); - current_tx_desc->lower.data = htole32( - adapter->txd_cmd | txd_lower | q.segs[j].ds_len); - current_tx_desc->upper.data = htole32(txd_upper); + ctxd->buffer_addr = htole64(segs[j].ds_addr); + ctxd->lower.data = htole32(adapter->txd_cmd | + txd_lower | segs[j].ds_len); + ctxd->upper.data = htole32(txd_upper); last = i; if (++i == adapter->num_tx_desc) @@ -1504,92 +1578,74 @@ em_encap(struct adapter *adapter, struct mbuf *m_head) } adapter->next_avail_tx_desc = i; - if (adapter->pcix_82544) + if (adapter->pcix_82544) { + KKASSERT(adapter->num_tx_desc_avail > txd_used); adapter->num_tx_desc_avail -= txd_used; - else - adapter->num_tx_desc_avail -= q.nsegs; + } else { + KKASSERT(adapter->num_tx_desc_avail > nsegs); + adapter->num_tx_desc_avail -= nsegs; + } - /* Find out if we are in vlan mode */ + /* Handle VLAN tag */ if (m_head->m_flags & M_VLANTAG) { - /* Set the vlan id */ - current_tx_desc->upper.fields.special = - htole16(m_head->m_pkthdr.ether_vlantag); + /* Set the vlan id. */ + ctxd->upper.fields.special = + htole16(m_head->m_pkthdr.ether_vlantag); /* Tell hardware to add tag */ - current_tx_desc->lower.data |= htole32(E1000_TXD_CMD_VLE); + ctxd->lower.data |= htole32(E1000_TXD_CMD_VLE); } tx_buffer->m_head = m_head; - tx_buffer_first->map = tx_buffer->map; + tx_buffer_mapped->map = tx_buffer->map; tx_buffer->map = map; - bus_dmamap_sync(adapter->txtag, map, BUS_DMASYNC_PREWRITE); /* * Last Descriptor of Packet needs End Of Packet (EOP) * and Report Status (RS) */ - current_tx_desc->lower.data |= - htole32(E1000_TXD_CMD_EOP | E1000_TXD_CMD_RS); + ctxd->lower.data |= htole32(E1000_TXD_CMD_EOP | E1000_TXD_CMD_RS); /* * Keep track in the first buffer which descriptor will be - * written back. + * written back */ - tx_buffer_first->next_eop = last; - - bus_dmamap_sync(adapter->txdma.dma_tag, adapter->txdma.dma_map, - BUS_DMASYNC_PREWRITE); + tx_buffer = &adapter->tx_buffer_area[first]; + tx_buffer->next_eop = last; - /* - * Advance the Transmit Descriptor Tail (Tdt), this tells the E1000 + /* + * Advance the Transmit Descriptor Tail (TDT), this tells the E1000 * that this frame is available to transmit. */ - if (adapter->hw.mac_type == em_82547 && + if (adapter->hw.mac.type == e1000_82547 && adapter->link_duplex == HALF_DUPLEX) { em_82547_move_tail_serialized(adapter); } else { - E1000_WRITE_REG(&adapter->hw, TDT, i); - if (adapter->hw.mac_type == em_82547) { + E1000_WRITE_REG(&adapter->hw, E1000_TDT(0), i); + if (adapter->hw.mac.type == e1000_82547) { em_82547_update_fifo_head(adapter, - m_head->m_pkthdr.len); + m_head->m_pkthdr.len); } } - return (0); -fail: - bus_dmamap_unload(adapter->txtag, map); - return error; } -/********************************************************************* - * +/* * 82547 workaround to avoid controller hang in half-duplex environment. * The workaround is to avoid queuing a large packet that would span - * the internal Tx FIFO ring boundary. We need to reset the FIFO pointers - * in this case. We do that only when FIFO is quiescent. - * - **********************************************************************/ -static void -em_82547_move_tail(void *arg) -{ - struct adapter *adapter = arg; - struct ifnet *ifp = &adapter->interface_data.ac_if; - - lwkt_serialize_enter(ifp->if_serializer); - em_82547_move_tail_serialized(adapter); - lwkt_serialize_exit(ifp->if_serializer); -} - + * the internal Tx FIFO ring boundary. We need to reset the FIFO pointers + * in this case. We do that only when FIFO is quiescent. + */ static void em_82547_move_tail_serialized(struct adapter *adapter) { - uint16_t hw_tdt; - uint16_t sw_tdt; - struct em_tx_desc *tx_desc; - uint16_t length = 0; - boolean_t eop = 0; + struct e1000_tx_desc *tx_desc; + uint16_t hw_tdt, sw_tdt, length = 0; + bool eop = 0; - hw_tdt = E1000_READ_REG(&adapter->hw, TDT); + ASSERT_SERIALIZED(adapter->arpcom.ac_if.if_serializer); + + hw_tdt = E1000_READ_REG(&adapter->hw, E1000_TDT(0)); sw_tdt = adapter->next_avail_tx_desc; while (hw_tdt != sw_tdt) { @@ -1606,11 +1662,22 @@ em_82547_move_tail_serialized(struct adapter *adapter) em_82547_move_tail, adapter); break; } - E1000_WRITE_REG(&adapter->hw, TDT, hw_tdt); + E1000_WRITE_REG(&adapter->hw, E1000_TDT(0), hw_tdt); em_82547_update_fifo_head(adapter, length); length = 0; } - } + } +} + +static void +em_82547_move_tail(void *xsc) +{ + struct adapter *adapter = xsc; + struct ifnet *ifp = &adapter->arpcom.ac_if; + + lwkt_serialize_enter(ifp->if_serializer); + em_82547_move_tail_serialized(adapter); + lwkt_serialize_exit(ifp->if_serializer); } static int @@ -1630,7 +1697,6 @@ em_82547_fifo_workaround(struct adapter *adapter, int len) return (1); } } - return (0); } @@ -1650,22 +1716,30 @@ em_82547_tx_fifo_reset(struct adapter *adapter) { uint32_t tctl; - if (E1000_READ_REG(&adapter->hw, TDT) == E1000_READ_REG(&adapter->hw, TDH) && - E1000_READ_REG(&adapter->hw, TDFT) == E1000_READ_REG(&adapter->hw, TDFH) && - E1000_READ_REG(&adapter->hw, TDFTS) == E1000_READ_REG(&adapter->hw, TDFHS) && - E1000_READ_REG(&adapter->hw, TDFPC) == 0) { + if ((E1000_READ_REG(&adapter->hw, E1000_TDT(0)) == + E1000_READ_REG(&adapter->hw, E1000_TDH(0))) && + (E1000_READ_REG(&adapter->hw, E1000_TDFT) == + E1000_READ_REG(&adapter->hw, E1000_TDFH)) && + (E1000_READ_REG(&adapter->hw, E1000_TDFTS) == + E1000_READ_REG(&adapter->hw, E1000_TDFHS)) && + (E1000_READ_REG(&adapter->hw, E1000_TDFPC) == 0)) { /* Disable TX unit */ - tctl = E1000_READ_REG(&adapter->hw, TCTL); - E1000_WRITE_REG(&adapter->hw, TCTL, tctl & ~E1000_TCTL_EN); + tctl = E1000_READ_REG(&adapter->hw, E1000_TCTL); + E1000_WRITE_REG(&adapter->hw, E1000_TCTL, + tctl & ~E1000_TCTL_EN); /* Reset FIFO pointers */ - E1000_WRITE_REG(&adapter->hw, TDFT, adapter->tx_head_addr); - E1000_WRITE_REG(&adapter->hw, TDFH, adapter->tx_head_addr); - E1000_WRITE_REG(&adapter->hw, TDFTS, adapter->tx_head_addr); - E1000_WRITE_REG(&adapter->hw, TDFHS, adapter->tx_head_addr); + E1000_WRITE_REG(&adapter->hw, E1000_TDFT, + adapter->tx_head_addr); + E1000_WRITE_REG(&adapter->hw, E1000_TDFH, + adapter->tx_head_addr); + E1000_WRITE_REG(&adapter->hw, E1000_TDFTS, + adapter->tx_head_addr); + E1000_WRITE_REG(&adapter->hw, E1000_TDFHS, + adapter->tx_head_addr); /* Re-enable TX unit */ - E1000_WRITE_REG(&adapter->hw, TCTL, tctl); + E1000_WRITE_REG(&adapter->hw, E1000_TCTL, tctl); E1000_WRITE_FLUSH(&adapter->hw); adapter->tx_fifo_head = 0; @@ -1680,18 +1754,21 @@ em_82547_tx_fifo_reset(struct adapter *adapter) static void em_set_promisc(struct adapter *adapter) { + struct ifnet *ifp = &adapter->arpcom.ac_if; uint32_t reg_rctl; - struct ifnet *ifp = &adapter->interface_data.ac_if; - reg_rctl = E1000_READ_REG(&adapter->hw, RCTL); + reg_rctl = E1000_READ_REG(&adapter->hw, E1000_RCTL); if (ifp->if_flags & IFF_PROMISC) { reg_rctl |= (E1000_RCTL_UPE | E1000_RCTL_MPE); - E1000_WRITE_REG(&adapter->hw, RCTL, reg_rctl); + /* Turn this on if you want to see bad packets */ + if (em_debug_sbp) + reg_rctl |= E1000_RCTL_SBP; + E1000_WRITE_REG(&adapter->hw, E1000_RCTL, reg_rctl); } else if (ifp->if_flags & IFF_ALLMULTI) { reg_rctl |= E1000_RCTL_MPE; reg_rctl &= ~E1000_RCTL_UPE; - E1000_WRITE_REG(&adapter->hw, RCTL, reg_rctl); + E1000_WRITE_REG(&adapter->hw, E1000_RCTL, reg_rctl); } } @@ -1700,37 +1777,30 @@ em_disable_promisc(struct adapter *adapter) { uint32_t reg_rctl; - reg_rctl = E1000_READ_REG(&adapter->hw, RCTL); + reg_rctl = E1000_READ_REG(&adapter->hw, E1000_RCTL); - reg_rctl &= (~E1000_RCTL_UPE); - reg_rctl &= (~E1000_RCTL_MPE); - E1000_WRITE_REG(&adapter->hw, RCTL, reg_rctl); + reg_rctl &= ~E1000_RCTL_UPE; + reg_rctl &= ~E1000_RCTL_MPE; + reg_rctl &= ~E1000_RCTL_SBP; + E1000_WRITE_REG(&adapter->hw, E1000_RCTL, reg_rctl); } -/********************************************************************* - * Multicast Update - * - * This routine is called whenever multicast address list is updated. - * - **********************************************************************/ - static void em_set_multi(struct adapter *adapter) { - uint32_t reg_rctl = 0; - uint8_t mta[MAX_NUM_MULTICAST_ADDRESSES * ETH_LENGTH_OF_ADDRESS]; + struct ifnet *ifp = &adapter->arpcom.ac_if; struct ifmultiaddr *ifma; + uint32_t reg_rctl = 0; + uint8_t mta[512]; /* Largest MTS is 4096 bits */ int mcnt = 0; - struct ifnet *ifp = &adapter->interface_data.ac_if; - - IOCTL_DEBUGOUT("em_set_multi: begin"); - if (adapter->hw.mac_type == em_82542_rev2_0) { - reg_rctl = E1000_READ_REG(&adapter->hw, RCTL); - if (adapter->hw.pci_cmd_word & CMD_MEM_WRT_INVALIDATE) - em_pci_clear_mwi(&adapter->hw); + if (adapter->hw.mac.type == e1000_82542 && + adapter->hw.revision_id == E1000_REVISION_2) { + reg_rctl = E1000_READ_REG(&adapter->hw, E1000_RCTL); + if (adapter->hw.bus.pci_cmd_word & CMD_MEM_WRT_INVALIDATE) + e1000_pci_clear_mwi(&adapter->hw); reg_rctl |= E1000_RCTL_RST; - E1000_WRITE_REG(&adapter->hw, RCTL, reg_rctl); + E1000_WRITE_REG(&adapter->hw, E1000_RCTL, reg_rctl); msec_delay(5); } @@ -1742,52 +1812,54 @@ em_set_multi(struct adapter *adapter) break; bcopy(LLADDR((struct sockaddr_dl *)ifma->ifma_addr), - &mta[mcnt*ETH_LENGTH_OF_ADDRESS], ETH_LENGTH_OF_ADDRESS); + &mta[mcnt * ETHER_ADDR_LEN], ETHER_ADDR_LEN); mcnt++; } if (mcnt >= MAX_NUM_MULTICAST_ADDRESSES) { - reg_rctl = E1000_READ_REG(&adapter->hw, RCTL); + reg_rctl = E1000_READ_REG(&adapter->hw, E1000_RCTL); reg_rctl |= E1000_RCTL_MPE; - E1000_WRITE_REG(&adapter->hw, RCTL, reg_rctl); + E1000_WRITE_REG(&adapter->hw, E1000_RCTL, reg_rctl); } else { - em_mc_addr_list_update(&adapter->hw, mta, mcnt, 0, 1); + e1000_update_mc_addr_list(&adapter->hw, mta, + mcnt, 1, adapter->hw.mac.rar_entry_count); } - if (adapter->hw.mac_type == em_82542_rev2_0) { - reg_rctl = E1000_READ_REG(&adapter->hw, RCTL); + if (adapter->hw.mac.type == e1000_82542 && + adapter->hw.revision_id == E1000_REVISION_2) { + reg_rctl = E1000_READ_REG(&adapter->hw, E1000_RCTL); reg_rctl &= ~E1000_RCTL_RST; - E1000_WRITE_REG(&adapter->hw, RCTL, reg_rctl); + E1000_WRITE_REG(&adapter->hw, E1000_RCTL, reg_rctl); msec_delay(5); - if (adapter->hw.pci_cmd_word & CMD_MEM_WRT_INVALIDATE) - em_pci_set_mwi(&adapter->hw); + if (adapter->hw.bus.pci_cmd_word & CMD_MEM_WRT_INVALIDATE) + e1000_pci_set_mwi(&adapter->hw); } } -/********************************************************************* - * Timer routine - * - * This routine checks for link status and updates statistics. - * - **********************************************************************/ - +/* + * This routine checks for link status and updates statistics. + */ static void -em_local_timer(void *arg) +em_timer(void *xsc) { - struct ifnet *ifp; - struct adapter *adapter = arg; - ifp = &adapter->interface_data.ac_if; + struct adapter *adapter = xsc; + struct ifnet *ifp = &adapter->arpcom.ac_if; lwkt_serialize_enter(ifp->if_serializer); - em_check_for_link(&adapter->hw); em_update_link_status(adapter); - em_update_stats_counters(adapter); - if (em_display_debug_stats && ifp->if_flags & IFF_RUNNING) + em_update_stats(adapter); + + /* Reset LAA into RAR[0] on 82571 */ + if (e1000_get_laa_state_82571(&adapter->hw) == TRUE) + e1000_rar_set(&adapter->hw, adapter->hw.mac.addr, 0); + + if (em_display_debug_stats && (ifp->if_flags & IFF_RUNNING)) em_print_hw_stats(adapter); + em_smartspeed(adapter); - callout_reset(&adapter->timer, hz, em_local_timer, adapter); + callout_reset(&adapter->timer, hz, em_timer, adapter); lwkt_serialize_exit(ifp->if_serializer); } @@ -1795,146 +1867,170 @@ em_local_timer(void *arg) static void em_update_link_status(struct adapter *adapter) { - struct ifnet *ifp; - ifp = &adapter->interface_data.ac_if; - - if (E1000_READ_REG(&adapter->hw, STATUS) & E1000_STATUS_LU) { - if (adapter->link_active == 0) { - em_get_speed_and_duplex(&adapter->hw, - &adapter->link_speed, - &adapter->link_duplex); - /* Check if we may set SPEED_MODE bit on PCI-E */ - if (adapter->link_speed == SPEED_1000 && - (adapter->hw.mac_type == em_82571 || - adapter->hw.mac_type == em_82572)) { - int tarc0; - - tarc0 = E1000_READ_REG(&adapter->hw, TARC0); - tarc0 |= SPEED_MODE_BIT; - E1000_WRITE_REG(&adapter->hw, TARC0, tarc0); - } - if (bootverbose) { - if_printf(&adapter->interface_data.ac_if, - "Link is up %d Mbps %s\n", - adapter->link_speed, - adapter->link_duplex == FULL_DUPLEX ? - "Full Duplex" : "Half Duplex"); - } - adapter->link_active = 1; - adapter->smartspeed = 0; - ifp->if_baudrate = adapter->link_speed * 1000000; - ifp->if_link_state = LINK_STATE_UP; - if_link_state_change(ifp); + struct e1000_hw *hw = &adapter->hw; + struct ifnet *ifp = &adapter->arpcom.ac_if; + device_t dev = adapter->dev; + uint32_t link_check = 0; + + /* Get the cached link value or read phy for real */ + switch (hw->phy.media_type) { + case e1000_media_type_copper: + if (hw->mac.get_link_status) { + /* Do the work to read phy */ + e1000_check_for_link(hw); + link_check = !hw->mac.get_link_status; + if (link_check) /* ESB2 fix */ + e1000_cfg_on_link_up(hw); + } else { + link_check = TRUE; } - } else { - if (adapter->link_active == 1) { - ifp->if_baudrate = 0; - adapter->link_speed = 0; - adapter->link_duplex = 0; - if (bootverbose) { - if_printf(&adapter->interface_data.ac_if, - "Link is Down\n"); - } - adapter->link_active = 0; - ifp->if_link_state = LINK_STATE_DOWN; - if_link_state_change(ifp); + break; + + case e1000_media_type_fiber: + e1000_check_for_link(hw); + link_check = + E1000_READ_REG(hw, E1000_STATUS) & E1000_STATUS_LU; + break; + + case e1000_media_type_internal_serdes: + e1000_check_for_link(hw); + link_check = adapter->hw.mac.serdes_has_link; + break; + + case e1000_media_type_unknown: + default: + break; + } + + /* Now check for a transition */ + if (link_check && adapter->link_active == 0) { + e1000_get_speed_and_duplex(hw, &adapter->link_speed, + &adapter->link_duplex); + /* Check if we must disable SPEED_MODE bit on PCI-E */ + if (adapter->link_speed != SPEED_1000 && + (hw->mac.type == e1000_82571 || + hw->mac.type == e1000_82572)) { + int tarc0; + + tarc0 = E1000_READ_REG(hw, E1000_TARC(0)); + tarc0 &= ~SPEED_MODE_BIT; + E1000_WRITE_REG(hw, E1000_TARC(0), tarc0); } + if (bootverbose) { + device_printf(dev, "Link is up %d Mbps %s\n", + adapter->link_speed, + ((adapter->link_duplex == FULL_DUPLEX) ? + "Full Duplex" : "Half Duplex")); + } + adapter->link_active = 1; + adapter->smartspeed = 0; + ifp->if_baudrate = adapter->link_speed * 1000000; + ifp->if_link_state = LINK_STATE_UP; + if_link_state_change(ifp); + } else if (!link_check && adapter->link_active == 1) { + ifp->if_baudrate = adapter->link_speed = 0; + adapter->link_duplex = 0; + if (bootverbose) + device_printf(dev, "Link is Down\n"); + adapter->link_active = 0; +#if 0 + /* Link down, disable watchdog */ + if->if_timer = 0; +#endif + ifp->if_link_state = LINK_STATE_DOWN; + if_link_state_change(ifp); } } -/********************************************************************* - * - * This routine disables all traffic on the adapter by issuing a - * global reset on the MAC and deallocates TX/RX buffers. - * - **********************************************************************/ - static void -em_stop(void *arg) +em_stop(struct adapter *adapter) { - struct ifnet *ifp; - struct adapter * adapter = arg; - ifp = &adapter->interface_data.ac_if; + struct ifnet *ifp = &adapter->arpcom.ac_if; + int i; ASSERT_SERIALIZED(ifp->if_serializer); - INIT_DEBUGOUT("em_stop: begin"); em_disable_intr(adapter); - em_reset_hw(&adapter->hw); + callout_stop(&adapter->timer); callout_stop(&adapter->tx_fifo_timer); - em_free_transmit_structures(adapter); - em_free_receive_structures(adapter); - /* Tell the stack that the interface is no longer active */ ifp->if_flags &= ~(IFF_RUNNING | IFF_OACTIVE); ifp->if_timer = 0; + + e1000_reset_hw(&adapter->hw); + if (adapter->hw.mac.type >= e1000_82544) + E1000_WRITE_REG(&adapter->hw, E1000_WUC, 0); + + for (i = 0; i < adapter->num_tx_desc; i++) { + struct em_buffer *tx_buffer = &adapter->tx_buffer_area[i]; + + if (tx_buffer->m_head != NULL) { + bus_dmamap_unload(adapter->txtag, tx_buffer->map); + m_freem(tx_buffer->m_head); + tx_buffer->m_head = NULL; + } + tx_buffer->next_eop = -1; + } + + for (i = 0; i < adapter->num_rx_desc; i++) { + struct em_buffer *rx_buffer = &adapter->rx_buffer_area[i]; + + if (rx_buffer->m_head != NULL) { + bus_dmamap_unload(adapter->rxtag, rx_buffer->map); + m_freem(rx_buffer->m_head); + rx_buffer->m_head = NULL; + } + } } -/********************************************************************* - * - * Determine hardware revision. - * - **********************************************************************/ -static void -em_identify_hardware(struct adapter *adapter) +static int +em_get_hw_info(struct adapter *adapter) { device_t dev = adapter->dev; - /* Make sure our PCI config space has the necessary stuff set */ - adapter->hw.pci_cmd_word = pci_read_config(dev, PCIR_COMMAND, 2); - if (!((adapter->hw.pci_cmd_word & PCIM_CMD_BUSMASTEREN) && - (adapter->hw.pci_cmd_word & PCIM_CMD_MEMEN))) { - device_printf(dev, "Memory Access and/or Bus Master bits " - "were not set!\n"); - adapter->hw.pci_cmd_word |= PCIM_CMD_BUSMASTEREN | - PCIM_CMD_MEMEN; - pci_write_config(dev, PCIR_COMMAND, - adapter->hw.pci_cmd_word, 2); - } - /* Save off the information about this board */ adapter->hw.vendor_id = pci_get_vendor(dev); adapter->hw.device_id = pci_get_device(dev); adapter->hw.revision_id = pci_get_revid(dev); adapter->hw.subsystem_vendor_id = pci_get_subvendor(dev); - adapter->hw.subsystem_id = pci_get_subdevice(dev); + adapter->hw.subsystem_device_id = pci_get_subdevice(dev); - /* Identify the MAC */ - if (em_set_mac_type(&adapter->hw)) - device_printf(dev, "Unknown MAC Type\n"); - - if (adapter->hw.mac_type == em_82541 || - adapter->hw.mac_type == em_82541_rev_2 || - adapter->hw.mac_type == em_82547 || - adapter->hw.mac_type == em_82547_rev_2) - adapter->hw.phy_init_script = TRUE; + /* Do Shared Code Init and Setup */ + if (e1000_set_mac_type(&adapter->hw)) + return ENXIO; + return 0; } static int -em_allocate_pci_resources(device_t dev) +em_alloc_pci_res(struct adapter *adapter) { - struct adapter *adapter = device_get_softc(dev); - int rid; + device_t dev = adapter->dev; + int val, rid, error = E1000_SUCCESS; + + /* Enable bus mastering */ + pci_enable_busmaster(dev); - rid = PCIR_BAR(0); - adapter->res_memory = bus_alloc_resource_any(dev, SYS_RES_MEMORY, - &rid, RF_ACTIVE); - if (adapter->res_memory == NULL) { + adapter->memory_rid = EM_BAR_MEM; + adapter->memory = bus_alloc_resource_any(dev, SYS_RES_MEMORY, + &adapter->memory_rid, RF_ACTIVE); + if (adapter->memory == NULL) { device_printf(dev, "Unable to allocate bus resource: memory\n"); - return ENXIO; + return (ENXIO); } adapter->osdep.mem_bus_space_tag = - rman_get_bustag(adapter->res_memory); + rman_get_bustag(adapter->memory); adapter->osdep.mem_bus_space_handle = - rman_get_bushandle(adapter->res_memory); + rman_get_bushandle(adapter->memory); + + /* XXX This is quite goofy, it is not actually used */ adapter->hw.hw_addr = (uint8_t *)&adapter->osdep.mem_bus_space_handle; - if (adapter->hw.mac_type > em_82543) { + /* Only older adapters use IO mapping */ + if (adapter->hw.mac.type > e1000_82543 && + adapter->hw.mac.type < e1000_82571) { /* Figure our where our IO BAR is ? */ - for (rid = PCIR_BAR(0); rid < PCIR_CIS;) { - uint32_t val; - + for (rid = PCIR_BAR(0); rid < PCIR_CARDBUSCIS;) { val = pci_read_config(dev, rid, 4); if (EM_BAR_TYPE(val) == EM_BAR_TYPE_IO) { adapter->io_rid = rid; @@ -1945,128 +2041,97 @@ em_allocate_pci_resources(device_t dev) if (EM_BAR_MEM_TYPE(val) == EM_BAR_MEM_TYPE_64BIT) rid += 4; } - if (rid >= PCIR_CIS) { + if (rid >= PCIR_CARDBUSCIS) { device_printf(dev, "Unable to locate IO BAR\n"); return (ENXIO); - } - - adapter->res_ioport = bus_alloc_resource_any(dev, - SYS_RES_IOPORT, &adapter->io_rid, RF_ACTIVE); - if (!(adapter->res_ioport)) { + } + adapter->ioport = bus_alloc_resource_any(dev, SYS_RES_IOPORT, + &adapter->io_rid, RF_ACTIVE); + if (adapter->ioport == NULL) { device_printf(dev, "Unable to allocate bus resource: " - "ioport\n"); - return ENXIO; + "ioport\n"); + return (ENXIO); } adapter->hw.io_base = 0; adapter->osdep.io_bus_space_tag = - rman_get_bustag(adapter->res_ioport); + rman_get_bustag(adapter->ioport); adapter->osdep.io_bus_space_handle = - rman_get_bushandle(adapter->res_ioport); + rman_get_bushandle(adapter->ioport); } - /* For ICH8 we need to find the flash memory. */ - if ((adapter->hw.mac_type == em_ich8lan) || - (adapter->hw.mac_type == em_ich9lan)) { - rid = EM_FLASH; - adapter->flash_mem = bus_alloc_resource_any(dev, - SYS_RES_MEMORY, &rid, RF_ACTIVE); - if (adapter->flash_mem == NULL) { - device_printf(dev, "Unable to allocate bus resource: " - "flash memory\n"); - return ENXIO; - } - adapter->osdep.flash_bus_space_tag = - rman_get_bustag(adapter->flash_mem); - adapter->osdep.flash_bus_space_handle = - rman_get_bushandle(adapter->flash_mem); - } - - rid = 0x0; - adapter->res_interrupt = bus_alloc_resource_any(dev, SYS_RES_IRQ, - &rid, RF_SHAREABLE | RF_ACTIVE); - if (adapter->res_interrupt == NULL) { + adapter->intr_rid = 0; + adapter->intr_res = bus_alloc_resource_any(dev, SYS_RES_IRQ, + &adapter->intr_rid, + RF_SHAREABLE | RF_ACTIVE); + if (adapter->intr_res == NULL) { device_printf(dev, "Unable to allocate bus resource: " - "interrupt\n"); - return ENXIO; + "interrupt\n"); + return (ENXIO); } + adapter->hw.bus.pci_cmd_word = pci_read_config(dev, PCIR_COMMAND, 2); adapter->hw.back = &adapter->osdep; - - return 0; + return (error); } static void -em_free_pci_resources(device_t dev) +em_free_pci_res(struct adapter *adapter) { - struct adapter *adapter = device_get_softc(dev); + device_t dev = adapter->dev; - if (adapter->res_interrupt != NULL) { - bus_release_resource(dev, SYS_RES_IRQ, 0, - adapter->res_interrupt); + if (adapter->intr_res != NULL) { + bus_release_resource(dev, SYS_RES_IRQ, + adapter->intr_rid, adapter->intr_res); } - if (adapter->res_memory != NULL) { - bus_release_resource(dev, SYS_RES_MEMORY, PCIR_BAR(0), - adapter->res_memory); + + if (adapter->memory != NULL) { + bus_release_resource(dev, SYS_RES_MEMORY, + adapter->memory_rid, adapter->memory); } - if (adapter->res_ioport != NULL) { - bus_release_resource(dev, SYS_RES_IOPORT, adapter->io_rid, - adapter->res_ioport); + if (adapter->flash != NULL) { + bus_release_resource(dev, SYS_RES_MEMORY, + adapter->flash_rid, adapter->flash); } - if (adapter->flash_mem != NULL) { - bus_release_resource(dev, SYS_RES_MEMORY, EM_FLASH, - adapter->flash_mem); + if (adapter->ioport != NULL) { + bus_release_resource(dev, SYS_RES_IOPORT, + adapter->io_rid, adapter->ioport); } } -/********************************************************************* - * - * Initialize the hardware to a configuration as specified by the - * adapter structure. The controller is reset, the EEPROM is - * verified, the MAC address is set, then the shared initialization - * routines are called. - * - **********************************************************************/ static int -em_hardware_init(struct adapter *adapter) +em_hw_init(struct adapter *adapter) { - uint16_t rx_buffer_size; + device_t dev = adapter->dev; + uint16_t rx_buffer_size; - INIT_DEBUGOUT("em_hardware_init: begin"); /* Issue a global reset */ - em_reset_hw(&adapter->hw); + e1000_reset_hw(&adapter->hw); + + /* Get control from any management/hw control */ + if ((adapter->hw.mac.type == e1000_82573 || + adapter->hw.mac.type == e1000_ich8lan || + adapter->hw.mac.type == e1000_ich10lan || + adapter->hw.mac.type == e1000_ich9lan) && + e1000_check_mng_mode(&adapter->hw)) + em_get_hw_control(adapter); /* When hardware is reset, fifo_head is also reset */ adapter->tx_fifo_head = 0; - /* Make sure we have a good EEPROM before we read from it */ - if (em_validate_eeprom_checksum(&adapter->hw) < 0) { - if (em_validate_eeprom_checksum(&adapter->hw) < 0) { - device_printf(adapter->dev, - "The EEPROM Checksum Is Not Valid\n"); - return (EIO); - } - } - - if (em_read_part_num(&adapter->hw, &(adapter->part_num)) < 0) { - device_printf(adapter->dev, - "EEPROM read error while reading part number\n"); - return (EIO); - } - /* Set up smart power down as default off on newer adapters. */ if (!em_smart_pwr_down && - (adapter->hw.mac_type == em_82571 || - adapter->hw.mac_type == em_82572)) { + (adapter->hw.mac.type == e1000_82571 || + adapter->hw.mac.type == e1000_82572)) { uint16_t phy_tmp = 0; /* Speed up time to link by disabling smart power down. */ - em_read_phy_reg(&adapter->hw, IGP02E1000_PHY_POWER_MGMT, - &phy_tmp); + e1000_read_phy_reg(&adapter->hw, + IGP02E1000_PHY_POWER_MGMT, &phy_tmp); phy_tmp &= ~IGP02E1000_PM_SPD; - em_write_phy_reg(&adapter->hw, IGP02E1000_PHY_POWER_MGMT, - phy_tmp); + e1000_write_phy_reg(&adapter->hw, + IGP02E1000_PHY_POWER_MGMT, phy_tmp); } /* @@ -2076,54 +2141,47 @@ em_hardware_init(struct adapter *adapter) * received after sending an XOFF. * - Low water mark works best when it is very near the high water mark. * This allows the receiver to restart by sending XON when it has - * drained a bit. Here we use an arbitary value of 1500 which will - * restart after one full frame is pulled from the buffer. There + * drained a bit. Here we use an arbitary value of 1500 which will + * restart after one full frame is pulled from the buffer. There * could be several smaller frames in the buffer and if so they will * not trigger the XON until their total number reduces the buffer * by 1500. * - The pause time is fairly large at 1000 x 512ns = 512 usec. */ - rx_buffer_size = ((E1000_READ_REG(&adapter->hw, PBA) & 0xffff) << 10); + rx_buffer_size = + (E1000_READ_REG(&adapter->hw, E1000_PBA) & 0xffff) << 10; - adapter->hw.fc_high_water = - rx_buffer_size - roundup2(adapter->hw.max_frame_size, 1024); - adapter->hw.fc_low_water = adapter->hw.fc_high_water - 1500; - if (adapter->hw.mac_type == em_80003es2lan) - adapter->hw.fc_pause_time = 0xFFFF; + adapter->hw.fc.high_water = rx_buffer_size - + roundup2(adapter->max_frame_size, 1024); + adapter->hw.fc.low_water = adapter->hw.fc.high_water - 1500; + + if (adapter->hw.mac.type == e1000_80003es2lan) + adapter->hw.fc.pause_time = 0xFFFF; else - adapter->hw.fc_pause_time = 1000; - adapter->hw.fc_send_xon = TRUE; - adapter->hw.fc = E1000_FC_FULL; + adapter->hw.fc.pause_time = EM_FC_PAUSE_TIME; + adapter->hw.fc.send_xon = TRUE; + adapter->hw.fc.requested_mode = e1000_fc_full; - if (em_init_hw(&adapter->hw) < 0) { - device_printf(adapter->dev, "Hardware Initialization Failed"); + if (e1000_init_hw(&adapter->hw) < 0) { + device_printf(dev, "Hardware Initialization Failed\n"); return (EIO); } - em_check_for_link(&adapter->hw); + e1000_check_for_link(&adapter->hw); return (0); } -/********************************************************************* - * - * Setup networking device structure and register an interface. - * - **********************************************************************/ static void -em_setup_interface(device_t dev, struct adapter *adapter) +em_setup_ifp(struct adapter *adapter) { - struct ifnet *ifp; - u_char fiber_type = IFM_1000_SX; /* default type */ - INIT_DEBUGOUT("em_setup_interface: begin"); + struct ifnet *ifp = &adapter->arpcom.ac_if; - ifp = &adapter->interface_data.ac_if; - if_initname(ifp, device_get_name(dev), device_get_unit(dev)); - ifp->if_mtu = ETHERMTU; - ifp->if_baudrate = 1000000000; - ifp->if_init = em_init; + if_initname(ifp, device_get_name(adapter->dev), + device_get_unit(adapter->dev)); ifp->if_softc = adapter; ifp->if_flags = IFF_BROADCAST | IFF_SIMPLEX | IFF_MULTICAST; + ifp->if_init = em_init; ifp->if_ioctl = em_ioctl; ifp->if_start = em_start; #ifdef DEVICE_POLLING @@ -2133,48 +2191,33 @@ em_setup_interface(device_t dev, struct adapter *adapter) ifq_set_maxlen(&ifp->if_snd, adapter->num_tx_desc - 1); ifq_set_ready(&ifp->if_snd); - if (adapter->hw.mac_type >= em_82543) - ifp->if_capabilities |= IFCAP_HWCSUM; + ether_ifattach(ifp, adapter->hw.mac.addr, NULL); - ifp->if_capenable = ifp->if_capabilities; + if (adapter->hw.mac.type >= e1000_82543) + ifp->if_capabilities = IFCAP_HWCSUM; - ether_ifattach(ifp, adapter->hw.mac_addr, NULL); + ifp->if_capabilities |= IFCAP_VLAN_HWTAGGING | IFCAP_VLAN_MTU; + ifp->if_capenable = ifp->if_capabilities; -#ifdef PROFILE_SERIALIZER - SYSCTL_ADD_UINT(&adapter->sysctl_ctx, - SYSCTL_CHILDREN(adapter->sysctl_tree), OID_AUTO, - "serializer_sleep", CTLFLAG_RW, - &ifp->if_serializer->sleep_cnt, 0, NULL); - SYSCTL_ADD_UINT(&adapter->sysctl_ctx, - SYSCTL_CHILDREN(adapter->sysctl_tree), OID_AUTO, - "serializer_tryfail", CTLFLAG_RW, - &ifp->if_serializer->tryfail_cnt, 0, NULL); - SYSCTL_ADD_UINT(&adapter->sysctl_ctx, - SYSCTL_CHILDREN(adapter->sysctl_tree), OID_AUTO, - "serializer_enter", CTLFLAG_RW, - &ifp->if_serializer->enter_cnt, 0, NULL); - SYSCTL_ADD_UINT(&adapter->sysctl_ctx, - SYSCTL_CHILDREN(adapter->sysctl_tree), OID_AUTO, - "serializer_try", CTLFLAG_RW, - &ifp->if_serializer->try_cnt, 0, NULL); -#endif + if (ifp->if_capenable & IFCAP_TXCSUM) + ifp->if_hwassist = EM_CSUM_FEATURES; /* * Tell the upper layer(s) we support long frames. */ ifp->if_data.ifi_hdrlen = sizeof(struct ether_vlan_header); - ifp->if_capabilities |= IFCAP_VLAN_HWTAGGING | IFCAP_VLAN_MTU; - ifp->if_capenable |= IFCAP_VLAN_HWTAGGING | IFCAP_VLAN_MTU; /* * Specify the media types supported by this adapter and register * callbacks to update media and link information */ - ifmedia_init(&adapter->media, IFM_IMASK, em_media_change, - em_media_status); - if (adapter->hw.media_type == em_media_type_fiber || - adapter->hw.media_type == em_media_type_internal_serdes) { - if (adapter->hw.mac_type == em_82545) + ifmedia_init(&adapter->media, IFM_IMASK, + em_media_change, em_media_status); + if (adapter->hw.phy.media_type == e1000_media_type_fiber || + adapter->hw.phy.media_type == e1000_media_type_internal_serdes) { + u_char fiber_type = IFM_1000_SX; /* default type */ + + if (adapter->hw.mac.type == e1000_82545) fiber_type = IFM_1000_LX; ifmedia_add(&adapter->media, IFM_ETHER | fiber_type | IFM_FDX, 0, NULL); @@ -2187,466 +2230,462 @@ em_setup_interface(device_t dev, struct adapter *adapter) 0, NULL); ifmedia_add(&adapter->media, IFM_ETHER | IFM_100_TX | IFM_FDX, 0, NULL); - ifmedia_add(&adapter->media, IFM_ETHER | IFM_1000_T | IFM_FDX, - 0, NULL); - ifmedia_add(&adapter->media, IFM_ETHER | IFM_1000_T, 0, NULL); + if (adapter->hw.phy.type != e1000_phy_ife) { + ifmedia_add(&adapter->media, + IFM_ETHER | IFM_1000_T | IFM_FDX, 0, NULL); + ifmedia_add(&adapter->media, + IFM_ETHER | IFM_1000_T, 0, NULL); + } } ifmedia_add(&adapter->media, IFM_ETHER | IFM_AUTO, 0, NULL); ifmedia_set(&adapter->media, IFM_ETHER | IFM_AUTO); } -/********************************************************************* - * - * Workaround for SmartSpeed on 82541 and 82547 controllers - * - **********************************************************************/ + +/* + * Workaround for SmartSpeed on 82541 and 82547 controllers + */ static void em_smartspeed(struct adapter *adapter) { uint16_t phy_tmp; - if (adapter->link_active || (adapter->hw.phy_type != em_phy_igp) || - !adapter->hw.autoneg || - !(adapter->hw.autoneg_advertised & ADVERTISE_1000_FULL)) + if (adapter->link_active || adapter->hw.phy.type != e1000_phy_igp || + adapter->hw.mac.autoneg == 0 || + (adapter->hw.phy.autoneg_advertised & ADVERTISE_1000_FULL) == 0) return; if (adapter->smartspeed == 0) { /* * If Master/Slave config fault is asserted twice, - * we assume back-to-back. + * we assume back-to-back */ - em_read_phy_reg(&adapter->hw, PHY_1000T_STATUS, &phy_tmp); + e1000_read_phy_reg(&adapter->hw, PHY_1000T_STATUS, &phy_tmp); if (!(phy_tmp & SR_1000T_MS_CONFIG_FAULT)) return; - em_read_phy_reg(&adapter->hw, PHY_1000T_STATUS, &phy_tmp); + e1000_read_phy_reg(&adapter->hw, PHY_1000T_STATUS, &phy_tmp); if (phy_tmp & SR_1000T_MS_CONFIG_FAULT) { - em_read_phy_reg(&adapter->hw, PHY_1000T_CTRL, &phy_tmp); + e1000_read_phy_reg(&adapter->hw, + PHY_1000T_CTRL, &phy_tmp); if (phy_tmp & CR_1000T_MS_ENABLE) { phy_tmp &= ~CR_1000T_MS_ENABLE; - em_write_phy_reg(&adapter->hw, - PHY_1000T_CTRL, phy_tmp); + e1000_write_phy_reg(&adapter->hw, + PHY_1000T_CTRL, phy_tmp); adapter->smartspeed++; - if (adapter->hw.autoneg && - !em_phy_setup_autoneg(&adapter->hw) && - !em_read_phy_reg(&adapter->hw, PHY_CTRL, - &phy_tmp)) { - phy_tmp |= (MII_CR_AUTO_NEG_EN | - MII_CR_RESTART_AUTO_NEG); - em_write_phy_reg(&adapter->hw, - PHY_CTRL, phy_tmp); + if (adapter->hw.mac.autoneg && + !e1000_phy_setup_autoneg(&adapter->hw) && + !e1000_read_phy_reg(&adapter->hw, + PHY_CONTROL, &phy_tmp)) { + phy_tmp |= MII_CR_AUTO_NEG_EN | + MII_CR_RESTART_AUTO_NEG; + e1000_write_phy_reg(&adapter->hw, + PHY_CONTROL, phy_tmp); } } } return; } else if (adapter->smartspeed == EM_SMARTSPEED_DOWNSHIFT) { /* If still no link, perhaps using 2/3 pair cable */ - em_read_phy_reg(&adapter->hw, PHY_1000T_CTRL, &phy_tmp); + e1000_read_phy_reg(&adapter->hw, PHY_1000T_CTRL, &phy_tmp); phy_tmp |= CR_1000T_MS_ENABLE; - em_write_phy_reg(&adapter->hw, PHY_1000T_CTRL, phy_tmp); - if (adapter->hw.autoneg && - !em_phy_setup_autoneg(&adapter->hw) && - !em_read_phy_reg(&adapter->hw, PHY_CTRL, &phy_tmp)) { - phy_tmp |= (MII_CR_AUTO_NEG_EN | - MII_CR_RESTART_AUTO_NEG); - em_write_phy_reg(&adapter->hw, PHY_CTRL, phy_tmp); + e1000_write_phy_reg(&adapter->hw, PHY_1000T_CTRL, phy_tmp); + if (adapter->hw.mac.autoneg && + !e1000_phy_setup_autoneg(&adapter->hw) && + !e1000_read_phy_reg(&adapter->hw, PHY_CONTROL, &phy_tmp)) { + phy_tmp |= MII_CR_AUTO_NEG_EN | MII_CR_RESTART_AUTO_NEG; + e1000_write_phy_reg(&adapter->hw, PHY_CONTROL, phy_tmp); } } + /* Restart process after EM_SMARTSPEED_MAX iterations */ if (adapter->smartspeed++ == EM_SMARTSPEED_MAX) adapter->smartspeed = 0; } -/* - * Manage DMA'able memory. - */ -static void -em_dmamap_cb(void *arg, bus_dma_segment_t *segs, int nseg, int error) -{ - if (error) - return; - *(bus_addr_t *)arg = segs->ds_addr; -} - static int em_dma_malloc(struct adapter *adapter, bus_size_t size, struct em_dma_alloc *dma) { - device_t dev = adapter->dev; - int error; - - error = bus_dma_tag_create(NULL, /* parent */ - EM_DBA_ALIGN, 0, /* alignment, bounds */ - BUS_SPACE_MAXADDR, /* lowaddr */ - BUS_SPACE_MAXADDR, /* highaddr */ - NULL, NULL, /* filter, filterarg */ - size, /* maxsize */ - 1, /* nsegments */ - size, /* maxsegsize */ - 0, /* flags */ - &dma->dma_tag); - if (error) { - device_printf(dev, "%s: bus_dma_tag_create failed; error %d\n", - __func__, error); - return error; - } - - error = bus_dmamem_alloc(dma->dma_tag, (void**)&dma->dma_vaddr, - BUS_DMA_WAITOK, &dma->dma_map); - if (error) { - device_printf(dev, "%s: bus_dmammem_alloc failed; " - "size %llu, error %d\n", - __func__, (uintmax_t)size, error); - goto fail; - } - - error = bus_dmamap_load(dma->dma_tag, dma->dma_map, - dma->dma_vaddr, size, - em_dmamap_cb, &dma->dma_paddr, - BUS_DMA_WAITOK); - if (error) { - device_printf(dev, "%s: bus_dmamap_load failed; error %u\n", - __func__, error); - bus_dmamem_free(dma->dma_tag, dma->dma_vaddr, dma->dma_map); - goto fail; - } - - return 0; -fail: - bus_dma_tag_destroy(dma->dma_tag); - dma->dma_tag = NULL; - return error; + dma->dma_vaddr = bus_dmamem_coherent_any(adapter->parent_dtag, + EM_DBA_ALIGN, size, BUS_DMA_WAITOK, + &dma->dma_tag, &dma->dma_map, + &dma->dma_paddr); + if (dma->dma_vaddr == NULL) + return ENOMEM; + else + return 0; } static void em_dma_free(struct adapter *adapter, struct em_dma_alloc *dma) { - if (dma->dma_tag != NULL) { - bus_dmamap_unload(dma->dma_tag, dma->dma_map); - bus_dmamem_free(dma->dma_tag, dma->dma_vaddr, dma->dma_map); - bus_dma_tag_destroy(dma->dma_tag); - dma->dma_tag = NULL; - } + if (dma->dma_tag == NULL) + return; + bus_dmamap_unload(dma->dma_tag, dma->dma_map); + bus_dmamem_free(dma->dma_tag, dma->dma_vaddr, dma->dma_map); + bus_dma_tag_destroy(dma->dma_tag); } -/********************************************************************* - * - * Allocate and initialize transmit structures. - * - **********************************************************************/ static int -em_setup_transmit_structures(struct adapter *adapter) +em_create_tx_ring(struct adapter *adapter) { + device_t dev = adapter->dev; struct em_buffer *tx_buffer; - bus_size_t size; int error, i; - /* - * Setup DMA descriptor areas. - */ - size = roundup2(adapter->hw.max_frame_size, MCLBYTES); - if (bus_dma_tag_create(NULL, /* parent */ - 1, 0, /* alignment, bounds */ - BUS_SPACE_MAXADDR, /* lowaddr */ - BUS_SPACE_MAXADDR, /* highaddr */ - NULL, NULL, /* filter, filterarg */ - size, /* maxsize */ - EM_MAX_SCATTER, /* nsegments */ - size, /* maxsegsize */ - 0, /* flags */ - &adapter->txtag)) { - device_printf(adapter->dev, "Unable to allocate TX DMA tag\n"); - return(ENOMEM); - } - adapter->tx_buffer_area = kmalloc(sizeof(struct em_buffer) * adapter->num_tx_desc, M_DEVBUF, M_WAITOK | M_ZERO); - bzero(adapter->tx_desc_base, - sizeof(struct em_tx_desc) * adapter->num_tx_desc); - tx_buffer = adapter->tx_buffer_area; + /* + * Create DMA tags for tx buffers + */ + error = bus_dma_tag_create(adapter->parent_dtag, /* parent */ + 1, 0, /* alignment, bounds */ + BUS_SPACE_MAXADDR, /* lowaddr */ + BUS_SPACE_MAXADDR, /* highaddr */ + NULL, NULL, /* filter, filterarg */ + EM_TSO_SIZE, /* maxsize */ + EM_MAX_SCATTER, /* nsegments */ + EM_MAX_SEGSIZE, /* maxsegsize */ + BUS_DMA_WAITOK | BUS_DMA_ALLOCNOW | + BUS_DMA_ONEBPAGE, /* flags */ + &adapter->txtag); + if (error) { + device_printf(dev, "Unable to allocate TX DMA tag\n"); + kfree(adapter->tx_buffer_area, M_DEVBUF); + adapter->tx_buffer_area = NULL; + return error; + } + + /* + * Create DMA maps for tx buffers + */ for (i = 0; i < adapter->num_tx_desc; i++) { - error = bus_dmamap_create(adapter->txtag, 0, &tx_buffer->map); + tx_buffer = &adapter->tx_buffer_area[i]; + + error = bus_dmamap_create(adapter->txtag, + BUS_DMA_WAITOK | BUS_DMA_ONEBPAGE, + &tx_buffer->map); if (error) { - device_printf(adapter->dev, - "Unable to create TX DMA map\n"); - goto fail; + device_printf(dev, "Unable to create TX DMA map\n"); + em_destroy_tx_ring(adapter, i); + return error; } - tx_buffer++; + tx_buffer->next_eop = -1; } + return (0); +} +static void +em_init_tx_ring(struct adapter *adapter) +{ + /* Clear the old ring contents */ + bzero(adapter->tx_desc_base, + (sizeof(struct e1000_tx_desc)) * adapter->num_tx_desc); + + /* Reset state */ adapter->next_avail_tx_desc = 0; adapter->next_tx_to_clean = 0; - - /* Set number of descriptors available */ adapter->num_tx_desc_avail = adapter->num_tx_desc; - - /* Set checksum context */ - adapter->active_checksum_context = OFFLOAD_NONE; - - bus_dmamap_sync(adapter->txdma.dma_tag, adapter->txdma.dma_map, - BUS_DMASYNC_PREWRITE); - - return (0); -fail: - em_free_transmit_structures(adapter); - return (error); } -/********************************************************************* - * - * Enable transmit unit. - * - **********************************************************************/ static void -em_initialize_transmit_unit(struct adapter *adapter) +em_init_tx_unit(struct adapter *adapter) { - uint32_t reg_tctl; - uint32_t reg_tipg = 0; + uint32_t tctl, tarc, tipg = 0; uint64_t bus_addr; - INIT_DEBUGOUT("em_initialize_transmit_unit: begin"); - /* Setup the Base and Length of the Tx Descriptor Ring */ bus_addr = adapter->txdma.dma_paddr; - E1000_WRITE_REG(&adapter->hw, TDLEN, - adapter->num_tx_desc * sizeof(struct em_tx_desc)); - E1000_WRITE_REG(&adapter->hw, TDBAH, (uint32_t)(bus_addr >> 32)); - E1000_WRITE_REG(&adapter->hw, TDBAL, (uint32_t)bus_addr); - + E1000_WRITE_REG(&adapter->hw, E1000_TDLEN(0), + adapter->num_tx_desc * sizeof(struct e1000_tx_desc)); + E1000_WRITE_REG(&adapter->hw, E1000_TDBAH(0), + (uint32_t)(bus_addr >> 32)); + E1000_WRITE_REG(&adapter->hw, E1000_TDBAL(0), + (uint32_t)bus_addr); /* Setup the HW Tx Head and Tail descriptor pointers */ - E1000_WRITE_REG(&adapter->hw, TDT, 0); - E1000_WRITE_REG(&adapter->hw, TDH, 0); - - HW_DEBUGOUT2("Base = %x, Length = %x\n", - E1000_READ_REG(&adapter->hw, TDBAL), - E1000_READ_REG(&adapter->hw, TDLEN)); + E1000_WRITE_REG(&adapter->hw, E1000_TDT(0), 0); + E1000_WRITE_REG(&adapter->hw, E1000_TDH(0), 0); /* Set the default values for the Tx Inter Packet Gap timer */ - switch (adapter->hw.mac_type) { - case em_82542_rev2_0: - case em_82542_rev2_1: - reg_tipg = DEFAULT_82542_TIPG_IPGT; - reg_tipg |= DEFAULT_82542_TIPG_IPGR1 << E1000_TIPG_IPGR1_SHIFT; - reg_tipg |= DEFAULT_82542_TIPG_IPGR2 << E1000_TIPG_IPGR2_SHIFT; + switch (adapter->hw.mac.type) { + case e1000_82542: + tipg = DEFAULT_82542_TIPG_IPGT; + tipg |= DEFAULT_82542_TIPG_IPGR1 << E1000_TIPG_IPGR1_SHIFT; + tipg |= DEFAULT_82542_TIPG_IPGR2 << E1000_TIPG_IPGR2_SHIFT; break; - case em_80003es2lan: - reg_tipg = DEFAULT_82543_TIPG_IPGR1; - reg_tipg |= - DEFAULT_80003ES2LAN_TIPG_IPGR2 << E1000_TIPG_IPGR2_SHIFT; + + case e1000_80003es2lan: + tipg = DEFAULT_82543_TIPG_IPGR1; + tipg |= DEFAULT_80003ES2LAN_TIPG_IPGR2 << + E1000_TIPG_IPGR2_SHIFT; break; + default: - if (adapter->hw.media_type == em_media_type_fiber || - adapter->hw.media_type == em_media_type_internal_serdes) - reg_tipg = DEFAULT_82543_TIPG_IPGT_FIBER; + if (adapter->hw.phy.media_type == e1000_media_type_fiber || + adapter->hw.phy.media_type == + e1000_media_type_internal_serdes) + tipg = DEFAULT_82543_TIPG_IPGT_FIBER; else - reg_tipg = DEFAULT_82543_TIPG_IPGT_COPPER; - reg_tipg |= DEFAULT_82543_TIPG_IPGR1 << E1000_TIPG_IPGR1_SHIFT; - reg_tipg |= DEFAULT_82543_TIPG_IPGR2 << E1000_TIPG_IPGR2_SHIFT; + tipg = DEFAULT_82543_TIPG_IPGT_COPPER; + tipg |= DEFAULT_82543_TIPG_IPGR1 << E1000_TIPG_IPGR1_SHIFT; + tipg |= DEFAULT_82543_TIPG_IPGR2 << E1000_TIPG_IPGR2_SHIFT; + break; + } + + E1000_WRITE_REG(&adapter->hw, E1000_TIPG, tipg); + E1000_WRITE_REG(&adapter->hw, E1000_TIDV, adapter->tx_int_delay.value); + if(adapter->hw.mac.type >= e1000_82540) { + E1000_WRITE_REG(&adapter->hw, E1000_TADV, + adapter->tx_abs_int_delay.value); } - E1000_WRITE_REG(&adapter->hw, TIPG, reg_tipg); - E1000_WRITE_REG(&adapter->hw, TIDV, adapter->tx_int_delay.value); - if (adapter->hw.mac_type >= em_82540) { - E1000_WRITE_REG(&adapter->hw, TADV, - adapter->tx_abs_int_delay.value); + if (adapter->hw.mac.type == e1000_82571 || + adapter->hw.mac.type == e1000_82572) { + tarc = E1000_READ_REG(&adapter->hw, E1000_TARC(0)); + tarc |= SPEED_MODE_BIT; + E1000_WRITE_REG(&adapter->hw, E1000_TARC(0), tarc); + } else if (adapter->hw.mac.type == e1000_80003es2lan) { + tarc = E1000_READ_REG(&adapter->hw, E1000_TARC(0)); + tarc |= 1; + E1000_WRITE_REG(&adapter->hw, E1000_TARC(0), tarc); + tarc = E1000_READ_REG(&adapter->hw, E1000_TARC(1)); + tarc |= 1; + E1000_WRITE_REG(&adapter->hw, E1000_TARC(1), tarc); } /* Program the Transmit Control Register */ - reg_tctl = E1000_TCTL_PSP | E1000_TCTL_EN | - (E1000_COLLISION_THRESHOLD << E1000_CT_SHIFT); - if (adapter->hw.mac_type >= em_82571) - reg_tctl |= E1000_TCTL_MULR; - if (adapter->link_duplex == 1) - reg_tctl |= E1000_FDX_COLLISION_DISTANCE << E1000_COLD_SHIFT; - else - reg_tctl |= E1000_HDX_COLLISION_DISTANCE << E1000_COLD_SHIFT; + tctl = E1000_READ_REG(&adapter->hw, E1000_TCTL); + tctl &= ~E1000_TCTL_CT; + tctl |= E1000_TCTL_PSP | E1000_TCTL_RTLC | E1000_TCTL_EN | + (E1000_COLLISION_THRESHOLD << E1000_CT_SHIFT); + + if (adapter->hw.mac.type >= e1000_82571) + tctl |= E1000_TCTL_MULR; /* This write will effectively turn on the transmit unit. */ - E1000_WRITE_REG(&adapter->hw, TCTL, reg_tctl); + E1000_WRITE_REG(&adapter->hw, E1000_TCTL, tctl); - /* Setup Transmit Descriptor Base Settings */ + /* Setup Transmit Descriptor Base Settings */ adapter->txd_cmd = E1000_TXD_CMD_IFCS; if (adapter->tx_int_delay.value > 0) adapter->txd_cmd |= E1000_TXD_CMD_IDE; } -/********************************************************************* - * - * Free all transmit related data structures. - * - **********************************************************************/ static void -em_free_transmit_structures(struct adapter *adapter) +em_destroy_tx_ring(struct adapter *adapter, int ndesc) { struct em_buffer *tx_buffer; int i; - INIT_DEBUGOUT("free_transmit_structures: begin"); + if (adapter->tx_buffer_area == NULL) + return; - if (adapter->tx_buffer_area != NULL) { - tx_buffer = adapter->tx_buffer_area; - for (i = 0; i < adapter->num_tx_desc; i++, tx_buffer++) { - if (tx_buffer->m_head != NULL) { - bus_dmamap_unload(adapter->txtag, - tx_buffer->map); - m_freem(tx_buffer->m_head); - } + for (i = 0; i < ndesc; i++) { + tx_buffer = &adapter->tx_buffer_area[i]; - if (tx_buffer->map != NULL) { - bus_dmamap_destroy(adapter->txtag, tx_buffer->map); - tx_buffer->map = NULL; - } - tx_buffer->m_head = NULL; - } - } - if (adapter->tx_buffer_area != NULL) { - kfree(adapter->tx_buffer_area, M_DEVBUF); - adapter->tx_buffer_area = NULL; - } - if (adapter->txtag != NULL) { - bus_dma_tag_destroy(adapter->txtag); - adapter->txtag = NULL; + KKASSERT(tx_buffer->m_head == NULL); + bus_dmamap_destroy(adapter->txtag, tx_buffer->map); } + bus_dma_tag_destroy(adapter->txtag); + + kfree(adapter->tx_buffer_area, M_DEVBUF); + adapter->tx_buffer_area = NULL; } -/********************************************************************* - * - * The offload context needs to be set when we transfer the first - * packet of a particular protocol (TCP/UDP). We change the - * context only if the protocol type changes. - * - **********************************************************************/ +/* + * The offload context needs to be set when we transfer the first + * packet of a particular protocol (TCP/UDP). This routine has been + * enhanced to deal with inserted VLAN headers, and IPV6 (not complete) + */ static void -em_transmit_checksum_setup(struct adapter *adapter, - struct mbuf *mp, - uint32_t *txd_upper, - uint32_t *txd_lower) +em_txcsum(struct adapter *adapter, struct mbuf *mp, + uint32_t *txd_upper, uint32_t *txd_lower) { - struct em_context_desc *TXD; + struct e1000_context_desc *TXD; struct em_buffer *tx_buffer; - int curr_txd; + struct ether_vlan_header *eh; + struct ip *ip = NULL; + struct ip6_hdr *ip6; + struct tcp_hdr *th; + int curr_txd, ehdrlen; + uint32_t cmd, hdr_len, ip_hlen; + uint16_t etype; + uint8_t ipproto; + + cmd = hdr_len = ipproto = 0; + + /* Setup checksum offload context. */ + curr_txd = adapter->next_avail_tx_desc; + tx_buffer = &adapter->tx_buffer_area[curr_txd]; + TXD = (struct e1000_context_desc *)&adapter->tx_desc_base[curr_txd]; - if (mp->m_pkthdr.csum_flags) { - if (mp->m_pkthdr.csum_flags & CSUM_TCP) { - *txd_upper = E1000_TXD_POPTS_TXSM << 8; - *txd_lower = E1000_TXD_CMD_DEXT | E1000_TXD_DTYP_D; - if (adapter->active_checksum_context == OFFLOAD_TCP_IP) - return; - else - adapter->active_checksum_context = OFFLOAD_TCP_IP; - } else if (mp->m_pkthdr.csum_flags & CSUM_UDP) { - *txd_upper = E1000_TXD_POPTS_TXSM << 8; - *txd_lower = E1000_TXD_CMD_DEXT | E1000_TXD_DTYP_D; - if (adapter->active_checksum_context == OFFLOAD_UDP_IP) - return; - else - adapter->active_checksum_context = OFFLOAD_UDP_IP; - } else { - *txd_upper = 0; - *txd_lower = 0; - return; - } + /* + * Determine where frame payload starts. + * Jump over vlan headers if already present, + * helpful for QinQ too. + */ + eh = mtod(mp, struct ether_vlan_header *); + if (eh->evl_encap_proto == htons(ETHERTYPE_VLAN)) { + etype = ntohs(eh->evl_proto); + ehdrlen = ETHER_HDR_LEN + EVL_ENCAPLEN; } else { - *txd_upper = 0; - *txd_lower = 0; - return; + etype = ntohs(eh->evl_encap_proto); + ehdrlen = ETHER_HDR_LEN; } /* - * If we reach this point, the checksum offload context - * needs to be reset. + * We only support TCP/UDP for IPv4 and IPv6 for the moment. + * TODO: Support SCTP too when it hits the tree. */ - curr_txd = adapter->next_avail_tx_desc; - tx_buffer = &adapter->tx_buffer_area[curr_txd]; - TXD = (struct em_context_desc *) &adapter->tx_desc_base[curr_txd]; + switch (etype) { + case ETHERTYPE_IP: + ip = (struct ip *)(mp->m_data + ehdrlen); + ip_hlen = ip->ip_hl << 2; + + /* Setup of IP header checksum. */ + if (mp->m_pkthdr.csum_flags & CSUM_IP) { + /* + * Start offset for header checksum calculation. + * End offset for header checksum calculation. + * Offset of place to put the checksum. + */ + TXD->lower_setup.ip_fields.ipcss = ehdrlen; + TXD->lower_setup.ip_fields.ipcse = + htole16(ehdrlen + ip_hlen - 1); + TXD->lower_setup.ip_fields.ipcso = + ehdrlen + offsetof(struct ip, ip_sum); + cmd |= E1000_TXD_CMD_IP; + *txd_upper |= E1000_TXD_POPTS_IXSM << 8; + } + + if (mp->m_len < ehdrlen + ip_hlen) + return; /* failure */ + + hdr_len = ehdrlen + ip_hlen; + ipproto = ip->ip_p; + + break; + + case ETHERTYPE_IPV6: + ip6 = (struct ip6_hdr *)(mp->m_data + ehdrlen); + ip_hlen = sizeof(struct ip6_hdr); /* XXX: No header stacking. */ + + if (mp->m_len < ehdrlen + ip_hlen) + return; /* failure */ - TXD->lower_setup.ip_fields.ipcss = ETHER_HDR_LEN; - TXD->lower_setup.ip_fields.ipcso = - ETHER_HDR_LEN + offsetof(struct ip, ip_sum); - TXD->lower_setup.ip_fields.ipcse = - htole16(ETHER_HDR_LEN + sizeof(struct ip) - 1); + /* IPv6 doesn't have a header checksum. */ - TXD->upper_setup.tcp_fields.tucss = - ETHER_HDR_LEN + sizeof(struct ip); - TXD->upper_setup.tcp_fields.tucse = htole16(0); + hdr_len = ehdrlen + ip_hlen; + ipproto = ip6->ip6_nxt; + + break; - if (adapter->active_checksum_context == OFFLOAD_TCP_IP) { - TXD->upper_setup.tcp_fields.tucso = - ETHER_HDR_LEN + sizeof(struct ip) + - offsetof(struct tcphdr, th_sum); - } else if (adapter->active_checksum_context == OFFLOAD_UDP_IP) { - TXD->upper_setup.tcp_fields.tucso = - ETHER_HDR_LEN + sizeof(struct ip) + - offsetof(struct udphdr, uh_sum); + default: + *txd_upper = 0; + *txd_lower = 0; + return; } - TXD->tcp_seg_setup.data = htole32(0); - TXD->cmd_and_length = htole32(adapter->txd_cmd | E1000_TXD_CMD_DEXT); + switch (ipproto) { + case IPPROTO_TCP: + if (mp->m_pkthdr.csum_flags & CSUM_TCP) { + /* + * Start offset for payload checksum calculation. + * End offset for payload checksum calculation. + * Offset of place to put the checksum. + */ + th = (struct tcp_hdr *)(mp->m_data + hdr_len); + TXD->upper_setup.tcp_fields.tucss = hdr_len; + TXD->upper_setup.tcp_fields.tucse = htole16(0); + TXD->upper_setup.tcp_fields.tucso = + hdr_len + offsetof(struct tcphdr, th_sum); + cmd |= E1000_TXD_CMD_TCP; + *txd_upper |= E1000_TXD_POPTS_TXSM << 8; + } + break; + case IPPROTO_UDP: + if (mp->m_pkthdr.csum_flags & CSUM_UDP) { + /* + * Start offset for header checksum calculation. + * End offset for header checksum calculation. + * Offset of place to put the checksum. + */ + TXD->upper_setup.tcp_fields.tucss = hdr_len; + TXD->upper_setup.tcp_fields.tucse = htole16(0); + TXD->upper_setup.tcp_fields.tucso = + hdr_len + offsetof(struct udphdr, uh_sum); + *txd_upper |= E1000_TXD_POPTS_TXSM << 8; + } + break; + + default: + break; + } + + *txd_lower = E1000_TXD_CMD_DEXT | /* Extended descr type */ + E1000_TXD_DTYP_D; /* Data descr */ + TXD->tcp_seg_setup.data = htole32(0); + TXD->cmd_and_length = + htole32(adapter->txd_cmd | E1000_TXD_CMD_DEXT | cmd); tx_buffer->m_head = NULL; tx_buffer->next_eop = -1; if (++curr_txd == adapter->num_tx_desc) curr_txd = 0; + KKASSERT(adapter->num_tx_desc_avail > 0); adapter->num_tx_desc_avail--; + adapter->next_avail_tx_desc = curr_txd; } -/********************************************************************** - * - * Examine each tx_buffer in the used queue. If the hardware is done - * processing the packet then free associated resources. The - * tx_buffer is put back on the free queue. - * - **********************************************************************/ - static void em_txeof(struct adapter *adapter) { int first, last, done, num_avail; struct em_buffer *tx_buffer; - struct em_tx_desc *tx_desc, *eop_desc; - struct ifnet *ifp = &adapter->interface_data.ac_if; + struct e1000_tx_desc *tx_desc, *eop_desc; + struct ifnet *ifp = &adapter->arpcom.ac_if; if (adapter->num_tx_desc_avail == adapter->num_tx_desc) return; - num_avail = adapter->num_tx_desc_avail; + num_avail = adapter->num_tx_desc_avail; first = adapter->next_tx_to_clean; + tx_desc = &adapter->tx_desc_base[first]; tx_buffer = &adapter->tx_buffer_area[first]; last = tx_buffer->next_eop; - KKASSERT(last >= 0 && last < adapter->num_tx_desc); eop_desc = &adapter->tx_desc_base[last]; /* - * Now caculate the terminating index for the cleanup loop below + * What this does is get the index of the + * first descriptor AFTER the EOP of the + * first packet, that way we can do the + * simple comparison on the inner while loop. */ if (++last == adapter->num_tx_desc) last = 0; done = last; - bus_dmamap_sync(adapter->txdma.dma_tag, adapter->txdma.dma_map, - BUS_DMASYNC_POSTREAD); - - while (eop_desc->upper.fields.status & E1000_TXD_STAT_DD) { + while (eop_desc->upper.fields.status & E1000_TXD_STAT_DD) { + /* We clean the range of the packet */ while (first != done) { + logif(pkt_txclean); + tx_desc->upper.data = 0; tx_desc->lower.data = 0; + tx_desc->buffer_addr = 0; num_avail++; - logif(pkt_txclean); - if (tx_buffer->m_head) { ifp->if_opackets++; - bus_dmamap_sync(adapter->txtag, tx_buffer->map, - BUS_DMASYNC_POSTWRITE); bus_dmamap_unload(adapter->txtag, tx_buffer->map); - m_freem(tx_buffer->m_head); tx_buffer->m_head = NULL; } @@ -2658,11 +2697,13 @@ em_txeof(struct adapter *adapter) tx_buffer = &adapter->tx_buffer_area[first]; tx_desc = &adapter->tx_desc_base[first]; } + /* See if we can continue to the next packet */ last = tx_buffer->next_eop; if (last != -1) { - KKASSERT(last >= 0 && last < adapter->num_tx_desc); eop_desc = &adapter->tx_desc_base[last]; + + /* Get new done point */ if (++last == adapter->num_tx_desc) last = 0; done = last; @@ -2670,156 +2711,164 @@ em_txeof(struct adapter *adapter) break; } } + adapter->next_tx_to_clean = first; + adapter->num_tx_desc_avail = num_avail; - bus_dmamap_sync(adapter->txdma.dma_tag, adapter->txdma.dma_map, - BUS_DMASYNC_PREWRITE); + if (adapter->num_tx_desc_avail > EM_TX_CLEANUP_THRESHOLD) { + ifp->if_flags &= ~IFF_OACTIVE; - adapter->next_tx_to_clean = first; + /* All clean, turn off the timer */ + if (adapter->num_tx_desc_avail == adapter->num_tx_desc) + ifp->if_timer = 0; + } +} - /* - * If we have enough room, clear IFF_OACTIVE to tell the stack - * that it is OK to send packets. - * If there are no pending descriptors, clear the timeout. Otherwise, - * if some descriptors have been freed, restart the timeout. - */ - if (num_avail > EM_TX_CLEANUP_THRESHOLD) { - ifp->if_flags &= ~IFF_OACTIVE; - if (num_avail == adapter->num_tx_desc) +/* + * When Link is lost sometimes there is work still in the TX ring + * which will result in a watchdog, rather than allow that do an + * attempted cleanup and then reinit here. Note that this has been + * seens mostly with fiber adapters. + */ +static void +em_tx_purge(struct adapter *adapter) +{ + struct ifnet *ifp = &adapter->arpcom.ac_if; + + if (!adapter->link_active && ifp->if_timer) { + em_txeof(adapter); + if (ifp->if_timer) { + if_printf(ifp, "Link lost, TX pending, reinit\n"); ifp->if_timer = 0; - else if (num_avail == adapter->num_tx_desc_avail) - ifp->if_timer = EM_TX_TIMEOUT; + em_init(adapter); + } } - adapter->num_tx_desc_avail = num_avail; } -/********************************************************************* - * - * Get a buffer from system mbuf buffer pool. - * - **********************************************************************/ static int -em_get_buf(int i, struct adapter *adapter, struct mbuf *nmp, int how) +em_newbuf(struct adapter *adapter, int i, int init) { - struct mbuf *mp = nmp; + struct mbuf *m; + bus_dma_segment_t seg; + bus_dmamap_t map; struct em_buffer *rx_buffer; - struct ifnet *ifp; - bus_addr_t paddr; - int error; - - ifp = &adapter->interface_data.ac_if; - - if (mp == NULL) { - mp = m_getcl(how, MT_DATA, M_PKTHDR); - if (mp == NULL) { - adapter->mbuf_cluster_failed++; - return (ENOBUFS); + int error, nseg; + + m = m_getcl(init ? MB_WAIT : MB_DONTWAIT, MT_DATA, M_PKTHDR); + if (m == NULL) { + adapter->mbuf_cluster_failed++; + if (init) { + if_printf(&adapter->arpcom.ac_if, + "Unable to allocate RX mbuf\n"); } - mp->m_len = mp->m_pkthdr.len = MCLBYTES; - } else { - mp->m_len = mp->m_pkthdr.len = MCLBYTES; - mp->m_data = mp->m_ext.ext_buf; - mp->m_next = NULL; + return (ENOBUFS); } + m->m_len = m->m_pkthdr.len = MCLBYTES; - if (ifp->if_mtu <= ETHERMTU) - m_adj(mp, ETHER_ALIGN); - - rx_buffer = &adapter->rx_buffer_area[i]; + if (adapter->max_frame_size <= MCLBYTES - ETHER_ALIGN) + m_adj(m, ETHER_ALIGN); - /* - * Using memory from the mbuf cluster pool, invoke the - * bus_dma machinery to arrange the memory mapping. - */ - error = bus_dmamap_load(adapter->rxtag, rx_buffer->map, - mtod(mp, void *), mp->m_len, - em_dmamap_cb, &paddr, 0); + error = bus_dmamap_load_mbuf_segment(adapter->rxtag, + adapter->rx_sparemap, m, + &seg, 1, &nseg, BUS_DMA_NOWAIT); if (error) { - m_freem(mp); + m_freem(m); + if (init) { + if_printf(&adapter->arpcom.ac_if, + "Unable to load RX mbuf\n"); + } return (error); } - rx_buffer->m_head = mp; - adapter->rx_desc_base[i].buffer_addr = htole64(paddr); - bus_dmamap_sync(adapter->rxtag, rx_buffer->map, BUS_DMASYNC_PREREAD); + rx_buffer = &adapter->rx_buffer_area[i]; + if (rx_buffer->m_head != NULL) + bus_dmamap_unload(adapter->rxtag, rx_buffer->map); + + map = rx_buffer->map; + rx_buffer->map = adapter->rx_sparemap; + adapter->rx_sparemap = map; + + rx_buffer->m_head = m; + + adapter->rx_desc_base[i].buffer_addr = htole64(seg.ds_addr); return (0); } -/********************************************************************* - * - * Allocate memory for rx_buffer structures. Since we use one - * rx_buffer per received packet, the maximum number of rx_buffer's - * that we'll need is equal to the number of receive descriptors - * that we've allocated. - * - **********************************************************************/ static int -em_allocate_receive_structures(struct adapter *adapter) +em_create_rx_ring(struct adapter *adapter) { - int i, error, size; + device_t dev = adapter->dev; struct em_buffer *rx_buffer; + int i, error; + + adapter->rx_buffer_area = + kmalloc(sizeof(struct em_buffer) * adapter->num_rx_desc, + M_DEVBUF, M_WAITOK | M_ZERO); - size = adapter->num_rx_desc * sizeof(struct em_buffer); - adapter->rx_buffer_area = kmalloc(size, M_DEVBUF, M_WAITOK | M_ZERO); - - error = bus_dma_tag_create(NULL, /* parent */ - 1, 0, /* alignment, bounds */ - BUS_SPACE_MAXADDR, /* lowaddr */ - BUS_SPACE_MAXADDR, /* highaddr */ - NULL, NULL, /* filter, filterarg */ - MCLBYTES, /* maxsize */ - 1, /* nsegments */ - MCLBYTES, /* maxsegsize */ - 0, /* flags */ - &adapter->rxtag); + /* + * Create DMA tag for rx buffers + */ + error = bus_dma_tag_create(adapter->parent_dtag, /* parent */ + 1, 0, /* alignment, bounds */ + BUS_SPACE_MAXADDR, /* lowaddr */ + BUS_SPACE_MAXADDR, /* highaddr */ + NULL, NULL, /* filter, filterarg */ + MCLBYTES, /* maxsize */ + 1, /* nsegments */ + MCLBYTES, /* maxsegsize */ + BUS_DMA_WAITOK | BUS_DMA_ALLOCNOW, /* flags */ + &adapter->rxtag); if (error) { - device_printf(adapter->dev, "%s: bus_dma_tag_create failed; " - "error %u\n", __func__, error); - goto fail; + device_printf(dev, "Unable to allocate RX DMA tag\n"); + kfree(adapter->rx_buffer_area, M_DEVBUF); + adapter->rx_buffer_area = NULL; + return error; + } + + /* + * Create spare DMA map for rx buffers + */ + error = bus_dmamap_create(adapter->rxtag, BUS_DMA_WAITOK, + &adapter->rx_sparemap); + if (error) { + device_printf(dev, "Unable to create spare RX DMA map\n"); + bus_dma_tag_destroy(adapter->rxtag); + kfree(adapter->rx_buffer_area, M_DEVBUF); + adapter->rx_buffer_area = NULL; + return error; } - - rx_buffer = adapter->rx_buffer_area; - for (i = 0; i < adapter->num_rx_desc; i++, rx_buffer++) { - error = bus_dmamap_create(adapter->rxtag, BUS_DMA_NOWAIT, + + /* + * Create DMA maps for rx buffers + */ + for (i = 0; i < adapter->num_rx_desc; i++) { + rx_buffer = &adapter->rx_buffer_area[i]; + + error = bus_dmamap_create(adapter->rxtag, BUS_DMA_WAITOK, &rx_buffer->map); if (error) { - device_printf(adapter->dev, - "%s: bus_dmamap_create failed; " - "error %u\n", __func__, error); - goto fail; + device_printf(dev, "Unable to create RX DMA map\n"); + em_destroy_rx_ring(adapter, i); + return error; } } - - for (i = 0; i < adapter->num_rx_desc; i++) { - error = em_get_buf(i, adapter, NULL, MB_DONTWAIT); - if (error) - goto fail; - } - - bus_dmamap_sync(adapter->rxdma.dma_tag, adapter->rxdma.dma_map, - BUS_DMASYNC_PREWRITE); - return (0); -fail: - em_free_receive_structures(adapter); - return (error); } -/********************************************************************* - * - * Allocate and initialize receive structures. - * - **********************************************************************/ static int -em_setup_receive_structures(struct adapter *adapter) +em_init_rx_ring(struct adapter *adapter) { - int error; + int i, error; + /* Reset descriptor ring */ bzero(adapter->rx_desc_base, - sizeof(struct em_rx_desc) * adapter->num_rx_desc); + (sizeof(struct e1000_rx_desc)) * adapter->num_rx_desc); - error = em_allocate_receive_structures(adapter); - if (error) - return (error); + /* Allocate new ones. */ + for (i = 0; i < adapter->num_rx_desc; i++) { + error = em_newbuf(adapter, i, 1); + if (error) + return (error); + } /* Setup our descriptor pointers */ adapter->next_rx_desc_to_check = 0; @@ -2827,191 +2876,179 @@ em_setup_receive_structures(struct adapter *adapter) return (0); } -/********************************************************************* - * - * Enable receive unit. - * - **********************************************************************/ static void -em_initialize_receive_unit(struct adapter *adapter) +em_init_rx_unit(struct adapter *adapter) { - uint32_t reg_rctl; - uint32_t reg_rxcsum; - struct ifnet *ifp; + struct ifnet *ifp = &adapter->arpcom.ac_if; uint64_t bus_addr; - - INIT_DEBUGOUT("em_initialize_receive_unit: begin"); - - ifp = &adapter->interface_data.ac_if; + uint32_t rctl, rxcsum; /* * Make sure receives are disabled while setting * up the descriptor ring */ - E1000_WRITE_REG(&adapter->hw, RCTL, 0); - - /* Set the Receive Delay Timer Register */ - E1000_WRITE_REG(&adapter->hw, RDTR, - adapter->rx_int_delay.value | E1000_RDT_FPDB); + rctl = E1000_READ_REG(&adapter->hw, E1000_RCTL); + E1000_WRITE_REG(&adapter->hw, E1000_RCTL, rctl & ~E1000_RCTL_EN); - if(adapter->hw.mac_type >= em_82540) { - E1000_WRITE_REG(&adapter->hw, RADV, - adapter->rx_abs_int_delay.value); + if (adapter->hw.mac.type >= e1000_82540) { + E1000_WRITE_REG(&adapter->hw, E1000_RADV, + adapter->rx_abs_int_delay.value); - /* Set the interrupt throttling rate in 256ns increments */ - if (em_int_throttle_ceil) { - E1000_WRITE_REG(&adapter->hw, ITR, - 1000000000 / 256 / em_int_throttle_ceil); + /* + * Set the interrupt throttling rate. Value is calculated + * as ITR = 1 / (INT_THROTTLE_CEIL * 256ns) + */ + if (adapter->int_throttle_ceil) { + E1000_WRITE_REG(&adapter->hw, E1000_ITR, + 1000000000 / 256 / adapter->int_throttle_ceil); } else { - E1000_WRITE_REG(&adapter->hw, ITR, 0); + E1000_WRITE_REG(&adapter->hw, E1000_ITR, 0); } } + /* Disable accelerated ackknowledge */ + if (adapter->hw.mac.type == e1000_82574) { + E1000_WRITE_REG(&adapter->hw, + E1000_RFCTL, E1000_RFCTL_ACK_DIS); + } + /* Setup the Base and Length of the Rx Descriptor Ring */ bus_addr = adapter->rxdma.dma_paddr; - E1000_WRITE_REG(&adapter->hw, RDLEN, adapter->num_rx_desc * - sizeof(struct em_rx_desc)); - E1000_WRITE_REG(&adapter->hw, RDBAH, (uint32_t)(bus_addr >> 32)); - E1000_WRITE_REG(&adapter->hw, RDBAL, (uint32_t)bus_addr); + E1000_WRITE_REG(&adapter->hw, E1000_RDLEN(0), + adapter->num_rx_desc * sizeof(struct e1000_rx_desc)); + E1000_WRITE_REG(&adapter->hw, E1000_RDBAH(0), + (uint32_t)(bus_addr >> 32)); + E1000_WRITE_REG(&adapter->hw, E1000_RDBAL(0), + (uint32_t)bus_addr); /* Setup the Receive Control Register */ - reg_rctl = E1000_RCTL_EN | E1000_RCTL_BAM | E1000_RCTL_LBM_NO | - E1000_RCTL_RDMTS_HALF | - (adapter->hw.mc_filter_type << E1000_RCTL_MO_SHIFT); + rctl &= ~(3 << E1000_RCTL_MO_SHIFT); + rctl |= E1000_RCTL_EN | E1000_RCTL_BAM | E1000_RCTL_LBM_NO | + E1000_RCTL_RDMTS_HALF | + (adapter->hw.mac.mc_filter_type << E1000_RCTL_MO_SHIFT); - if (adapter->hw.tbi_compatibility_on == TRUE) - reg_rctl |= E1000_RCTL_SBP; + /* Make sure VLAN Filters are off */ + rctl &= ~E1000_RCTL_VFE; + + if (e1000_tbi_sbp_enabled_82543(&adapter->hw)) + rctl |= E1000_RCTL_SBP; + else + rctl &= ~E1000_RCTL_SBP; switch (adapter->rx_buffer_len) { default: - case EM_RXBUFFER_2048: - reg_rctl |= E1000_RCTL_SZ_2048; + case 2048: + rctl |= E1000_RCTL_SZ_2048; + break; + + case 4096: + rctl |= E1000_RCTL_SZ_4096 | + E1000_RCTL_BSEX | E1000_RCTL_LPE; break; - case EM_RXBUFFER_4096: - reg_rctl |= E1000_RCTL_SZ_4096 | E1000_RCTL_BSEX | - E1000_RCTL_LPE; - break; - case EM_RXBUFFER_8192: - reg_rctl |= E1000_RCTL_SZ_8192 | E1000_RCTL_BSEX | - E1000_RCTL_LPE; + + case 8192: + rctl |= E1000_RCTL_SZ_8192 | + E1000_RCTL_BSEX | E1000_RCTL_LPE; break; - case EM_RXBUFFER_16384: - reg_rctl |= E1000_RCTL_SZ_16384 | E1000_RCTL_BSEX | - E1000_RCTL_LPE; + + case 16384: + rctl |= E1000_RCTL_SZ_16384 | + E1000_RCTL_BSEX | E1000_RCTL_LPE; break; } if (ifp->if_mtu > ETHERMTU) - reg_rctl |= E1000_RCTL_LPE; + rctl |= E1000_RCTL_LPE; + else + rctl &= ~E1000_RCTL_LPE; - /* Enable 82543 Receive Checksum Offload for TCP and UDP */ - if ((adapter->hw.mac_type >= em_82543) && - (ifp->if_capenable & IFCAP_RXCSUM)) { - reg_rxcsum = E1000_READ_REG(&adapter->hw, RXCSUM); - reg_rxcsum |= (E1000_RXCSUM_IPOFL | E1000_RXCSUM_TUOFL); - E1000_WRITE_REG(&adapter->hw, RXCSUM, reg_rxcsum); + /* Receive Checksum Offload for TCP and UDP */ + if (ifp->if_capenable & IFCAP_RXCSUM) { + rxcsum = E1000_READ_REG(&adapter->hw, E1000_RXCSUM); + rxcsum |= (E1000_RXCSUM_IPOFL | E1000_RXCSUM_TUOFL); + E1000_WRITE_REG(&adapter->hw, E1000_RXCSUM, rxcsum); } -#ifdef EM_X60_WORKAROUND - if (adapter->hw.mac_type == em_82573) - E1000_WRITE_REG(&adapter->hw, RDTR, 32); -#endif + /* + * XXX TEMPORARY WORKAROUND: on some systems with 82573 + * long latencies are observed, like Lenovo X60. This + * change eliminates the problem, but since having positive + * values in RDTR is a known source of problems on other + * platforms another solution is being sought. + */ + if (adapter->hw.mac.type == e1000_82573) + E1000_WRITE_REG(&adapter->hw, E1000_RDTR, 0x20); /* Enable Receives */ - E1000_WRITE_REG(&adapter->hw, RCTL, reg_rctl); + E1000_WRITE_REG(&adapter->hw, E1000_RCTL, rctl); - /* Setup the HW Rx Head and Tail Descriptor Pointers */ - E1000_WRITE_REG(&adapter->hw, RDH, 0); - E1000_WRITE_REG(&adapter->hw, RDT, adapter->num_rx_desc - 1); + /* + * Setup the HW Rx Head and Tail Descriptor Pointers + */ + E1000_WRITE_REG(&adapter->hw, E1000_RDH(0), 0); + E1000_WRITE_REG(&adapter->hw, E1000_RDT(0), adapter->num_rx_desc - 1); } -/********************************************************************* - * - * Free receive related data structures. - * - **********************************************************************/ static void -em_free_receive_structures(struct adapter *adapter) +em_destroy_rx_ring(struct adapter *adapter, int ndesc) { struct em_buffer *rx_buffer; int i; - INIT_DEBUGOUT("free_receive_structures: begin"); + if (adapter->rx_buffer_area == NULL) + return; - if (adapter->rx_buffer_area != NULL) { - rx_buffer = adapter->rx_buffer_area; - for (i = 0; i < adapter->num_rx_desc; i++, rx_buffer++) { - if (rx_buffer->m_head != NULL) { - bus_dmamap_unload(adapter->rxtag, - rx_buffer->map); - m_freem(rx_buffer->m_head); - rx_buffer->m_head = NULL; - } - if (rx_buffer->map != NULL) { - bus_dmamap_destroy(adapter->rxtag, - rx_buffer->map); - rx_buffer->map = NULL; - } - } - } - if (adapter->rx_buffer_area != NULL) { - kfree(adapter->rx_buffer_area, M_DEVBUF); - adapter->rx_buffer_area = NULL; - } - if (adapter->rxtag != NULL) { - bus_dma_tag_destroy(adapter->rxtag); - adapter->rxtag = NULL; + for (i = 0; i < ndesc; i++) { + rx_buffer = &adapter->rx_buffer_area[i]; + + KKASSERT(rx_buffer->m_head == NULL); + bus_dmamap_destroy(adapter->rxtag, rx_buffer->map); } + bus_dmamap_destroy(adapter->rxtag, adapter->rx_sparemap); + bus_dma_tag_destroy(adapter->rxtag); + + kfree(adapter->rx_buffer_area, M_DEVBUF); + adapter->rx_buffer_area = NULL; } -/********************************************************************* - * - * This routine executes in interrupt context. It replenishes - * the mbufs in the descriptor and sends data which has been - * dma'ed into host memory to upper layer. - * - * We loop at most count times if count is > 0, or until done if - * count < 0. - * - *********************************************************************/ static void em_rxeof(struct adapter *adapter, int count) { - struct ifnet *ifp; - struct mbuf *mp; - uint8_t accept_frame = 0; - uint8_t eop = 0; + struct ifnet *ifp = &adapter->arpcom.ac_if; + uint8_t status, accept_frame = 0, eop = 0; uint16_t len, desc_len, prev_len_adj; + struct e1000_rx_desc *current_desc; + struct mbuf *mp; int i; struct mbuf_chain chain[MAXCPU]; - /* Pointer to the receive descriptor being examined. */ - struct em_rx_desc *current_desc; - - ifp = &adapter->interface_data.ac_if; i = adapter->next_rx_desc_to_check; current_desc = &adapter->rx_desc_base[i]; - bus_dmamap_sync(adapter->rxdma.dma_tag, adapter->rxdma.dma_map, - BUS_DMASYNC_POSTREAD); - if (!(current_desc->status & E1000_RXD_STAT_DD)) return; ether_input_chain_init(chain); while ((current_desc->status & E1000_RXD_STAT_DD) && count != 0) { + struct mbuf *m = NULL; + logif(pkt_receive); + mp = adapter->rx_buffer_area[i].m_head; + + /* + * Can't defer bus_dmamap_sync(9) because TBI_ACCEPT + * needs to access the last received byte in the mbuf. + */ bus_dmamap_sync(adapter->rxtag, adapter->rx_buffer_area[i].map, BUS_DMASYNC_POSTREAD); - bus_dmamap_unload(adapter->rxtag, - adapter->rx_buffer_area[i].map); accept_frame = 1; prev_len_adj = 0; desc_len = le16toh(current_desc->length); - if (current_desc->status & E1000_RXD_STAT_EOP) { + status = current_desc->status; + if (status & E1000_RXD_STAT_EOP) { count--; eop = 1; if (desc_len < ETHER_CRC_LEN) { @@ -3026,21 +3063,20 @@ em_rxeof(struct adapter *adapter, int count) } if (current_desc->errors & E1000_RXD_ERR_FRAME_ERR_MASK) { - uint8_t last_byte; + uint8_t last_byte; uint32_t pkt_len = desc_len; if (adapter->fmp != NULL) - pkt_len += adapter->fmp->m_pkthdr.len; + pkt_len += adapter->fmp->m_pkthdr.len; last_byte = *(mtod(mp, caddr_t) + desc_len - 1); - - if (TBI_ACCEPT(&adapter->hw, current_desc->status, - current_desc->errors, - pkt_len, last_byte)) { - em_tbi_adjust_stats(&adapter->hw, - &adapter->stats, - pkt_len, - adapter->hw.mac_addr); + if (TBI_ACCEPT(&adapter->hw, status, + current_desc->errors, pkt_len, last_byte, + adapter->min_frame_size, adapter->max_frame_size)) { + e1000_tbi_adjust_stats_82543(&adapter->hw, + &adapter->stats, pkt_len, + adapter->hw.mac.addr, + adapter->max_frame_size); if (len > 0) len--; } else { @@ -3049,14 +3085,9 @@ em_rxeof(struct adapter *adapter, int count) } if (accept_frame) { - if (em_get_buf(i, adapter, NULL, MB_DONTWAIT) == ENOBUFS) { - adapter->dropped_pkts++; - em_get_buf(i, adapter, mp, MB_DONTWAIT); - if (adapter->fmp != NULL) - m_freem(adapter->fmp); - adapter->fmp = NULL; - adapter->lmp = NULL; - goto skip; + if (em_newbuf(adapter, i, 0) != 0) { + ifp->if_iqdrops++; + goto discard; } /* Assign correct length to the current fragment */ @@ -3064,18 +3095,22 @@ em_rxeof(struct adapter *adapter, int count) if (adapter->fmp == NULL) { mp->m_pkthdr.len = len; - adapter->fmp = mp; /* Store the first mbuf */ + adapter->fmp = mp; /* Store the first mbuf */ adapter->lmp = mp; } else { - /* Chain mbuf's together */ - /* + /* + * Chain mbuf's together + */ + + /* * Adjust length of previous mbuf in chain if * we received less than 4 bytes in the last * descriptor. */ if (prev_len_adj > 0) { adapter->lmp->m_len -= prev_len_adj; - adapter->fmp->m_pkthdr.len -= prev_len_adj; + adapter->fmp->m_pkthdr.len -= + prev_len_adj; } adapter->lmp->m_next = mp; adapter->lmp = adapter->lmp->m_next; @@ -3086,258 +3121,298 @@ em_rxeof(struct adapter *adapter, int count) adapter->fmp->m_pkthdr.rcvif = ifp; ifp->if_ipackets++; - em_receive_checksum(adapter, current_desc, - adapter->fmp); - if (current_desc->status & E1000_RXD_STAT_VP) { - adapter->fmp->m_flags |= M_VLANTAG; + if (ifp->if_capenable & IFCAP_RXCSUM) { + em_rxcsum(adapter, current_desc, + adapter->fmp); + } + + if (status & E1000_RXD_STAT_VP) { adapter->fmp->m_pkthdr.ether_vlantag = - (current_desc->special & - E1000_RXD_SPC_VLAN_MASK); + (le16toh(current_desc->special) & + E1000_RXD_SPC_VLAN_MASK); + adapter->fmp->m_flags |= M_VLANTAG; } - ether_input_chain(ifp, adapter->fmp, chain); + m = adapter->fmp; adapter->fmp = NULL; adapter->lmp = NULL; } } else { - adapter->dropped_pkts++; - em_get_buf(i, adapter, mp, MB_DONTWAIT); - if (adapter->fmp != NULL) + ifp->if_ierrors++; +discard: +#ifdef foo + /* Reuse loaded DMA map and just update mbuf chain */ + mp = adapter->rx_buffer_area[i].m_head; + mp->m_len = mp->m_pkthdr.len = MCLBYTES; + mp->m_data = mp->m_ext.ext_buf; + mp->m_next = NULL; + if (adapter->max_frame_size <= (MCLBYTES - ETHER_ALIGN)) + m_adj(mp, ETHER_ALIGN); +#endif + if (adapter->fmp != NULL) { m_freem(adapter->fmp); - adapter->fmp = NULL; - adapter->lmp = NULL; + adapter->fmp = NULL; + adapter->lmp = NULL; + } + m = NULL; } -skip: /* Zero out the receive descriptors status. */ current_desc->status = 0; + if (m != NULL) + ether_input_chain(ifp, m, chain); + /* Advance our pointers to the next descriptor. */ - if (++i == adapter->num_rx_desc) { + if (++i == adapter->num_rx_desc) i = 0; - current_desc = adapter->rx_desc_base; - } else { - current_desc++; - } + current_desc = &adapter->rx_desc_base[i]; } + adapter->next_rx_desc_to_check = i; ether_input_dispatch(chain); - bus_dmamap_sync(adapter->rxdma.dma_tag, adapter->rxdma.dma_map, - BUS_DMASYNC_PREWRITE); - - adapter->next_rx_desc_to_check = i; - /* Advance the E1000's Receive Queue #0 "Tail Pointer". */ if (--i < 0) i = adapter->num_rx_desc - 1; - - E1000_WRITE_REG(&adapter->hw, RDT, i); + E1000_WRITE_REG(&adapter->hw, E1000_RDT(0), i); } -/********************************************************************* - * - * Verify that the hardware indicated that the checksum is valid. - * Inform the stack about the status of checksum so that stack - * doesn't spend time verifying the checksum. - * - *********************************************************************/ static void -em_receive_checksum(struct adapter *adapter, - struct em_rx_desc *rx_desc, - struct mbuf *mp) +em_rxcsum(struct adapter *adapter, struct e1000_rx_desc *rx_desc, + struct mbuf *mp) { /* 82543 or newer only */ - if ((adapter->hw.mac_type < em_82543) || + if (adapter->hw.mac.type < e1000_82543 || /* Ignore Checksum bit is set */ - (rx_desc->status & E1000_RXD_STAT_IXSM)) { - mp->m_pkthdr.csum_flags = 0; + (rx_desc->status & E1000_RXD_STAT_IXSM)) return; - } - if (rx_desc->status & E1000_RXD_STAT_IPCS) { - /* Did it pass? */ - if (!(rx_desc->errors & E1000_RXD_ERR_IPE)) { - /* IP Checksum Good */ - mp->m_pkthdr.csum_flags = CSUM_IP_CHECKED; - mp->m_pkthdr.csum_flags |= CSUM_IP_VALID; - } else { - mp->m_pkthdr.csum_flags = 0; - } + if ((rx_desc->status & E1000_RXD_STAT_IPCS) && + !(rx_desc->errors & E1000_RXD_ERR_IPE)) { + /* IP Checksum Good */ + mp->m_pkthdr.csum_flags |= CSUM_IP_CHECKED | CSUM_IP_VALID; } - if (rx_desc->status & E1000_RXD_STAT_TCPCS) { - /* Did it pass? */ - if (!(rx_desc->errors & E1000_RXD_ERR_TCPE)) { - mp->m_pkthdr.csum_flags |= - (CSUM_DATA_VALID | CSUM_PSEUDO_HDR | - CSUM_FRAG_NOT_CHECKED); - mp->m_pkthdr.csum_data = htons(0xffff); - } + if ((rx_desc->status & E1000_RXD_STAT_TCPCS) && + !(rx_desc->errors & E1000_RXD_ERR_TCPE)) { + mp->m_pkthdr.csum_flags |= CSUM_DATA_VALID | + CSUM_PSEUDO_HDR | + CSUM_FRAG_NOT_CHECKED; + mp->m_pkthdr.csum_data = htons(0xffff); } } - -static void -em_enable_vlans(struct adapter *adapter) +static void +em_enable_intr(struct adapter *adapter) { - uint32_t ctrl; - - E1000_WRITE_REG(&adapter->hw, VET, ETHERTYPE_VLAN); - - ctrl = E1000_READ_REG(&adapter->hw, CTRL); - ctrl |= E1000_CTRL_VME; - E1000_WRITE_REG(&adapter->hw, CTRL, ctrl); + lwkt_serialize_handler_enable(adapter->arpcom.ac_if.if_serializer); + E1000_WRITE_REG(&adapter->hw, E1000_IMS, IMS_ENABLE_MASK); } static void -em_disable_vlans(struct adapter *adapter) +em_disable_intr(struct adapter *adapter) { - uint32_t ctrl; - - ctrl = E1000_READ_REG(&adapter->hw, CTRL); - ctrl &= ~E1000_CTRL_VME; - E1000_WRITE_REG(&adapter->hw, CTRL, ctrl); + E1000_WRITE_REG(&adapter->hw, E1000_IMC, 0xffffffff); + lwkt_serialize_handler_disable(adapter->arpcom.ac_if.if_serializer); } /* - * note: we must call bus_enable_intr() prior to enabling the hardware - * interrupt and bus_disable_intr() after disabling the hardware interrupt - * in order to avoid handler execution races from scheduled interrupt - * threads. + * Bit of a misnomer, what this really means is + * to enable OS management of the system... aka + * to disable special hardware management features */ static void -em_enable_intr(struct adapter *adapter) -{ - struct ifnet *ifp = &adapter->interface_data.ac_if; - - if ((ifp->if_flags & IFF_POLLING) == 0) { - lwkt_serialize_handler_enable(ifp->if_serializer); - E1000_WRITE_REG(&adapter->hw, IMS, (IMS_ENABLE_MASK)); +em_get_mgmt(struct adapter *adapter) +{ + /* A shared code workaround */ +#define E1000_82542_MANC2H E1000_MANC2H + if (adapter->has_manage) { + int manc2h = E1000_READ_REG(&adapter->hw, E1000_MANC2H); + int manc = E1000_READ_REG(&adapter->hw, E1000_MANC); + + /* disable hardware interception of ARP */ + manc &= ~(E1000_MANC_ARP_EN); + + /* enable receiving management packets to the host */ + if (adapter->hw.mac.type >= e1000_82571) { + manc |= E1000_MANC_EN_MNG2HOST; +#define E1000_MNG2HOST_PORT_623 (1 << 5) +#define E1000_MNG2HOST_PORT_664 (1 << 6) + manc2h |= E1000_MNG2HOST_PORT_623; + manc2h |= E1000_MNG2HOST_PORT_664; + E1000_WRITE_REG(&adapter->hw, E1000_MANC2H, manc2h); + } + + E1000_WRITE_REG(&adapter->hw, E1000_MANC, manc); } } +/* + * Give control back to hardware management + * controller if there is one. + */ static void -em_disable_intr(struct adapter *adapter) +em_rel_mgmt(struct adapter *adapter) { - /* - * The first version of 82542 had an errata where when link was forced - * it would stay up even up even if the cable was disconnected. - * Sequence errors were used to detect the disconnect and then the - * driver would unforce the link. This code in the in the ISR. For - * this to work correctly the Sequence error interrupt had to be - * enabled all the time. - */ - if (adapter->hw.mac_type == em_82542_rev2_0) { - E1000_WRITE_REG(&adapter->hw, IMC, - (0xffffffff & ~E1000_IMC_RXSEQ)); - } else { - E1000_WRITE_REG(&adapter->hw, IMC, 0xffffffff); - } + if (adapter->has_manage) { + int manc = E1000_READ_REG(&adapter->hw, E1000_MANC); - lwkt_serialize_handler_disable(adapter->interface_data.ac_if.if_serializer); -} + /* re-enable hardware interception of ARP */ + manc |= E1000_MANC_ARP_EN; -static int -em_is_valid_ether_addr(uint8_t *addr) -{ - static const char zero_addr[6] = { 0, 0, 0, 0, 0, 0 }; + if (adapter->hw.mac.type >= e1000_82571) + manc &= ~E1000_MANC_EN_MNG2HOST; - if ((addr[0] & 1) || !bcmp(addr, zero_addr, ETHER_ADDR_LEN)) - return (FALSE); - else - return (TRUE); + E1000_WRITE_REG(&adapter->hw, E1000_MANC, manc); + } } -void -em_write_pci_cfg(struct em_hw *hw, uint32_t reg, uint16_t *value) +/* + * em_get_hw_control() sets {CTRL_EXT|FWSM}:DRV_LOAD bit. + * For ASF and Pass Through versions of f/w this means that + * the driver is loaded. For AMT version (only with 82573) + * of the f/w this means that the network i/f is open. + */ +static void +em_get_hw_control(struct adapter *adapter) { - pci_write_config(((struct em_osdep *)hw->back)->dev, reg, *value, 2); -} + uint32_t ctrl_ext, swsm; -void -em_read_pci_cfg(struct em_hw *hw, uint32_t reg, uint16_t *value) -{ - *value = pci_read_config(((struct em_osdep *)hw->back)->dev, reg, 2); + /* Let firmware know the driver has taken over */ + switch (adapter->hw.mac.type) { + case e1000_82573: + swsm = E1000_READ_REG(&adapter->hw, E1000_SWSM); + E1000_WRITE_REG(&adapter->hw, E1000_SWSM, + swsm | E1000_SWSM_DRV_LOAD); + break; + case e1000_82571: + case e1000_82572: + case e1000_80003es2lan: + case e1000_ich8lan: + case e1000_ich9lan: + case e1000_ich10lan: + ctrl_ext = E1000_READ_REG(&adapter->hw, E1000_CTRL_EXT); + E1000_WRITE_REG(&adapter->hw, E1000_CTRL_EXT, + ctrl_ext | E1000_CTRL_EXT_DRV_LOAD); + break; + default: + break; + } } -void -em_pci_set_mwi(struct em_hw *hw) +/* + * em_rel_hw_control() resets {CTRL_EXT|FWSM}:DRV_LOAD bit. + * For ASF and Pass Through versions of f/w this means that the + * driver is no longer loaded. For AMT version (only with 82573) + * of the f/w this means that the network i/f is closed. + */ +static void +em_rel_hw_control(struct adapter *adapter) { - pci_write_config(((struct em_osdep *)hw->back)->dev, PCIR_COMMAND, - (hw->pci_cmd_word | CMD_MEM_WRT_INVALIDATE), 2); -} + uint32_t ctrl_ext, swsm; -void -em_pci_clear_mwi(struct em_hw *hw) -{ - pci_write_config(((struct em_osdep *)hw->back)->dev, PCIR_COMMAND, - (hw->pci_cmd_word & ~CMD_MEM_WRT_INVALIDATE), 2); -} + /* Let firmware taken over control of h/w */ + switch (adapter->hw.mac.type) { + case e1000_82573: + swsm = E1000_READ_REG(&adapter->hw, E1000_SWSM); + E1000_WRITE_REG(&adapter->hw, E1000_SWSM, + swsm & ~E1000_SWSM_DRV_LOAD); + break; -uint32_t -em_io_read(struct em_hw *hw, unsigned long port) -{ - struct em_osdep *io = hw->back; + case e1000_82571: + case e1000_82572: + case e1000_80003es2lan: + case e1000_ich8lan: + case e1000_ich9lan: + case e1000_ich10lan: + ctrl_ext = E1000_READ_REG(&adapter->hw, E1000_CTRL_EXT); + E1000_WRITE_REG(&adapter->hw, E1000_CTRL_EXT, + ctrl_ext & ~E1000_CTRL_EXT_DRV_LOAD); + break; - return bus_space_read_4(io->io_bus_space_tag, - io->io_bus_space_handle, port); + default: + break; + } } -void -em_io_write(struct em_hw *hw, unsigned long port, uint32_t value) +static int +em_is_valid_eaddr(const uint8_t *addr) { - struct em_osdep *io = hw->back; + char zero_addr[ETHER_ADDR_LEN] = { 0, 0, 0, 0, 0, 0 }; + + if ((addr[0] & 1) || !bcmp(addr, zero_addr, ETHER_ADDR_LEN)) + return (FALSE); - bus_space_write_4(io->io_bus_space_tag, - io->io_bus_space_handle, port, value); + return (TRUE); } /* - * We may eventually really do this, but its unnecessary - * for now so we just return unsupported. + * Enable PCI Wake On Lan capability */ -int32_t -em_read_pcie_cap_reg(struct em_hw *hw, uint32_t reg, uint16_t *value) +void +em_enable_wol(device_t dev) { - return (0); + uint16_t cap, status; + uint8_t id; + + /* First find the capabilities pointer*/ + cap = pci_read_config(dev, PCIR_CAP_PTR, 2); + + /* Read the PM Capabilities */ + id = pci_read_config(dev, cap, 1); + if (id != PCIY_PMG) /* Something wrong */ + return; + + /* + * OK, we have the power capabilities, + * so now get the status register + */ + cap += PCIR_POWER_STATUS; + status = pci_read_config(dev, cap, 2); + status |= PCIM_PSTAT_PME | PCIM_PSTAT_PMEENABLE; + pci_write_config(dev, cap, status, 2); } -/********************************************************************* +/* * 82544 Coexistence issue workaround. * There are 2 issues. - * 1. Transmit Hang issue. + * 1. Transmit Hang issue. * To detect this issue, following equation can be used... - * SIZE[3:0] + ADDR[2:0] = SUM[3:0]. - * If SUM[3:0] is in between 1 to 4, we will have this issue. + * SIZE[3:0] + ADDR[2:0] = SUM[3:0]. + * If SUM[3:0] is in between 1 to 4, we will have this issue. * - * 2. DAC issue. + * 2. DAC issue. * To detect this issue, following equation can be used... - * SIZE[3:0] + ADDR[2:0] = SUM[3:0]. - * If SUM[3:0] is in between 9 to c, we will have this issue. - * + * SIZE[3:0] + ADDR[2:0] = SUM[3:0]. + * If SUM[3:0] is in between 9 to c, we will have this issue. * * WORKAROUND: - * Make sure we do not have ending address as 1,2,3,4(Hang) or - * 9,a,b,c (DAC) - * -*************************************************************************/ + * Make sure we do not have ending address + * as 1,2,3,4(Hang) or 9,a,b,c (DAC) + */ static uint32_t -em_fill_descriptors(bus_addr_t address, uint32_t length, PDESC_ARRAY desc_array) +em_82544_fill_desc(bus_addr_t address, uint32_t length, PDESC_ARRAY desc_array) { - /* Since issue is sensitive to length and address.*/ - /* Let us first check the address...*/ uint32_t safe_terminator; + + /* + * Since issue is sensitive to length and address. + * Let us first check the address... + */ if (length <= 4) { desc_array->descriptor[0].address = address; desc_array->descriptor[0].length = length; desc_array->elements = 1; return (desc_array->elements); } - safe_terminator = (uint32_t)((((uint32_t)address & 0x7) + (length & 0xF)) & 0xF); - /* if it does not fall between 0x1 to 0x4 and 0x9 to 0xC then return */ + + safe_terminator = + (uint32_t)((((uint32_t)address & 0x7) + (length & 0xF)) & 0xF); + + /* If it does not fall between 0x1 to 0x4 and 0x9 to 0xC then return */ if (safe_terminator == 0 || - (safe_terminator > 4 && safe_terminator < 9) || + (safe_terminator > 4 && safe_terminator < 9) || (safe_terminator > 0xC && safe_terminator <= 0xF)) { desc_array->descriptor[0].address = address; desc_array->descriptor[0].length = length; @@ -3353,226 +3428,242 @@ em_fill_descriptors(bus_addr_t address, uint32_t length, PDESC_ARRAY desc_array) return (desc_array->elements); } -/********************************************************************** - * - * Update the board statistics counters. - * - **********************************************************************/ static void -em_update_stats_counters(struct adapter *adapter) -{ - struct ifnet *ifp; - - if (adapter->hw.media_type == em_media_type_copper || - (E1000_READ_REG(&adapter->hw, STATUS) & E1000_STATUS_LU)) { - adapter->stats.symerrs += E1000_READ_REG(&adapter->hw, SYMERRS); - adapter->stats.sec += E1000_READ_REG(&adapter->hw, SEC); - } - adapter->stats.crcerrs += E1000_READ_REG(&adapter->hw, CRCERRS); - adapter->stats.mpc += E1000_READ_REG(&adapter->hw, MPC); - adapter->stats.scc += E1000_READ_REG(&adapter->hw, SCC); - adapter->stats.ecol += E1000_READ_REG(&adapter->hw, ECOL); - - adapter->stats.mcc += E1000_READ_REG(&adapter->hw, MCC); - adapter->stats.latecol += E1000_READ_REG(&adapter->hw, LATECOL); - adapter->stats.colc += E1000_READ_REG(&adapter->hw, COLC); - adapter->stats.dc += E1000_READ_REG(&adapter->hw, DC); - adapter->stats.rlec += E1000_READ_REG(&adapter->hw, RLEC); - adapter->stats.xonrxc += E1000_READ_REG(&adapter->hw, XONRXC); - adapter->stats.xontxc += E1000_READ_REG(&adapter->hw, XONTXC); - adapter->stats.xoffrxc += E1000_READ_REG(&adapter->hw, XOFFRXC); - adapter->stats.xofftxc += E1000_READ_REG(&adapter->hw, XOFFTXC); - adapter->stats.fcruc += E1000_READ_REG(&adapter->hw, FCRUC); - adapter->stats.prc64 += E1000_READ_REG(&adapter->hw, PRC64); - adapter->stats.prc127 += E1000_READ_REG(&adapter->hw, PRC127); - adapter->stats.prc255 += E1000_READ_REG(&adapter->hw, PRC255); - adapter->stats.prc511 += E1000_READ_REG(&adapter->hw, PRC511); - adapter->stats.prc1023 += E1000_READ_REG(&adapter->hw, PRC1023); - adapter->stats.prc1522 += E1000_READ_REG(&adapter->hw, PRC1522); - adapter->stats.gprc += E1000_READ_REG(&adapter->hw, GPRC); - adapter->stats.bprc += E1000_READ_REG(&adapter->hw, BPRC); - adapter->stats.mprc += E1000_READ_REG(&adapter->hw, MPRC); - adapter->stats.gptc += E1000_READ_REG(&adapter->hw, GPTC); +em_update_stats(struct adapter *adapter) +{ + struct ifnet *ifp = &adapter->arpcom.ac_if; + + if (adapter->hw.phy.media_type == e1000_media_type_copper || + (E1000_READ_REG(&adapter->hw, E1000_STATUS) & E1000_STATUS_LU)) { + adapter->stats.symerrs += + E1000_READ_REG(&adapter->hw, E1000_SYMERRS); + adapter->stats.sec += E1000_READ_REG(&adapter->hw, E1000_SEC); + } + adapter->stats.crcerrs += E1000_READ_REG(&adapter->hw, E1000_CRCERRS); + adapter->stats.mpc += E1000_READ_REG(&adapter->hw, E1000_MPC); + adapter->stats.scc += E1000_READ_REG(&adapter->hw, E1000_SCC); + adapter->stats.ecol += E1000_READ_REG(&adapter->hw, E1000_ECOL); + + adapter->stats.mcc += E1000_READ_REG(&adapter->hw, E1000_MCC); + adapter->stats.latecol += E1000_READ_REG(&adapter->hw, E1000_LATECOL); + adapter->stats.colc += E1000_READ_REG(&adapter->hw, E1000_COLC); + adapter->stats.dc += E1000_READ_REG(&adapter->hw, E1000_DC); + adapter->stats.rlec += E1000_READ_REG(&adapter->hw, E1000_RLEC); + adapter->stats.xonrxc += E1000_READ_REG(&adapter->hw, E1000_XONRXC); + adapter->stats.xontxc += E1000_READ_REG(&adapter->hw, E1000_XONTXC); + adapter->stats.xoffrxc += E1000_READ_REG(&adapter->hw, E1000_XOFFRXC); + adapter->stats.xofftxc += E1000_READ_REG(&adapter->hw, E1000_XOFFTXC); + adapter->stats.fcruc += E1000_READ_REG(&adapter->hw, E1000_FCRUC); + adapter->stats.prc64 += E1000_READ_REG(&adapter->hw, E1000_PRC64); + adapter->stats.prc127 += E1000_READ_REG(&adapter->hw, E1000_PRC127); + adapter->stats.prc255 += E1000_READ_REG(&adapter->hw, E1000_PRC255); + adapter->stats.prc511 += E1000_READ_REG(&adapter->hw, E1000_PRC511); + adapter->stats.prc1023 += E1000_READ_REG(&adapter->hw, E1000_PRC1023); + adapter->stats.prc1522 += E1000_READ_REG(&adapter->hw, E1000_PRC1522); + adapter->stats.gprc += E1000_READ_REG(&adapter->hw, E1000_GPRC); + adapter->stats.bprc += E1000_READ_REG(&adapter->hw, E1000_BPRC); + adapter->stats.mprc += E1000_READ_REG(&adapter->hw, E1000_MPRC); + adapter->stats.gptc += E1000_READ_REG(&adapter->hw, E1000_GPTC); /* For the 64-bit byte counters the low dword must be read first. */ /* Both registers clear on the read of the high dword */ - adapter->stats.gorcl += E1000_READ_REG(&adapter->hw, GORCL); - adapter->stats.gorch += E1000_READ_REG(&adapter->hw, GORCH); - adapter->stats.gotcl += E1000_READ_REG(&adapter->hw, GOTCL); - adapter->stats.gotch += E1000_READ_REG(&adapter->hw, GOTCH); - - adapter->stats.rnbc += E1000_READ_REG(&adapter->hw, RNBC); - adapter->stats.ruc += E1000_READ_REG(&adapter->hw, RUC); - adapter->stats.rfc += E1000_READ_REG(&adapter->hw, RFC); - adapter->stats.roc += E1000_READ_REG(&adapter->hw, ROC); - adapter->stats.rjc += E1000_READ_REG(&adapter->hw, RJC); - - adapter->stats.torl += E1000_READ_REG(&adapter->hw, TORL); - adapter->stats.torh += E1000_READ_REG(&adapter->hw, TORH); - adapter->stats.totl += E1000_READ_REG(&adapter->hw, TOTL); - adapter->stats.toth += E1000_READ_REG(&adapter->hw, TOTH); - - adapter->stats.tpr += E1000_READ_REG(&adapter->hw, TPR); - adapter->stats.tpt += E1000_READ_REG(&adapter->hw, TPT); - adapter->stats.ptc64 += E1000_READ_REG(&adapter->hw, PTC64); - adapter->stats.ptc127 += E1000_READ_REG(&adapter->hw, PTC127); - adapter->stats.ptc255 += E1000_READ_REG(&adapter->hw, PTC255); - adapter->stats.ptc511 += E1000_READ_REG(&adapter->hw, PTC511); - adapter->stats.ptc1023 += E1000_READ_REG(&adapter->hw, PTC1023); - adapter->stats.ptc1522 += E1000_READ_REG(&adapter->hw, PTC1522); - adapter->stats.mptc += E1000_READ_REG(&adapter->hw, MPTC); - adapter->stats.bptc += E1000_READ_REG(&adapter->hw, BPTC); - - if (adapter->hw.mac_type >= em_82543) { + adapter->stats.gorc += E1000_READ_REG(&adapter->hw, E1000_GORCH); + adapter->stats.gotc += E1000_READ_REG(&adapter->hw, E1000_GOTCH); + + adapter->stats.rnbc += E1000_READ_REG(&adapter->hw, E1000_RNBC); + adapter->stats.ruc += E1000_READ_REG(&adapter->hw, E1000_RUC); + adapter->stats.rfc += E1000_READ_REG(&adapter->hw, E1000_RFC); + adapter->stats.roc += E1000_READ_REG(&adapter->hw, E1000_ROC); + adapter->stats.rjc += E1000_READ_REG(&adapter->hw, E1000_RJC); + + adapter->stats.tor += E1000_READ_REG(&adapter->hw, E1000_TORH); + adapter->stats.tot += E1000_READ_REG(&adapter->hw, E1000_TOTH); + + adapter->stats.tpr += E1000_READ_REG(&adapter->hw, E1000_TPR); + adapter->stats.tpt += E1000_READ_REG(&adapter->hw, E1000_TPT); + adapter->stats.ptc64 += E1000_READ_REG(&adapter->hw, E1000_PTC64); + adapter->stats.ptc127 += E1000_READ_REG(&adapter->hw, E1000_PTC127); + adapter->stats.ptc255 += E1000_READ_REG(&adapter->hw, E1000_PTC255); + adapter->stats.ptc511 += E1000_READ_REG(&adapter->hw, E1000_PTC511); + adapter->stats.ptc1023 += E1000_READ_REG(&adapter->hw, E1000_PTC1023); + adapter->stats.ptc1522 += E1000_READ_REG(&adapter->hw, E1000_PTC1522); + adapter->stats.mptc += E1000_READ_REG(&adapter->hw, E1000_MPTC); + adapter->stats.bptc += E1000_READ_REG(&adapter->hw, E1000_BPTC); + + if (adapter->hw.mac.type >= e1000_82543) { adapter->stats.algnerrc += - E1000_READ_REG(&adapter->hw, ALGNERRC); + E1000_READ_REG(&adapter->hw, E1000_ALGNERRC); adapter->stats.rxerrc += - E1000_READ_REG(&adapter->hw, RXERRC); + E1000_READ_REG(&adapter->hw, E1000_RXERRC); adapter->stats.tncrs += - E1000_READ_REG(&adapter->hw, TNCRS); + E1000_READ_REG(&adapter->hw, E1000_TNCRS); adapter->stats.cexterr += - E1000_READ_REG(&adapter->hw, CEXTERR); + E1000_READ_REG(&adapter->hw, E1000_CEXTERR); adapter->stats.tsctc += - E1000_READ_REG(&adapter->hw, TSCTC); + E1000_READ_REG(&adapter->hw, E1000_TSCTC); adapter->stats.tsctfc += - E1000_READ_REG(&adapter->hw, TSCTFC); + E1000_READ_REG(&adapter->hw, E1000_TSCTFC); } - ifp = &adapter->interface_data.ac_if; - /* Fill out the OS statistics structure */ ifp->if_collisions = adapter->stats.colc; /* Rx Errors */ ifp->if_ierrors = - adapter->dropped_pkts + - adapter->stats.rxerrc + - adapter->stats.crcerrs + - adapter->stats.algnerrc + - adapter->stats.ruc + adapter->stats.roc + - adapter->stats.mpc + adapter->stats.cexterr + - adapter->rx_overruns; + adapter->dropped_pkts + adapter->stats.rxerrc + + adapter->stats.crcerrs + adapter->stats.algnerrc + + adapter->stats.ruc + adapter->stats.roc + + adapter->stats.mpc + adapter->stats.cexterr; /* Tx Errors */ - ifp->if_oerrors = adapter->stats.ecol + adapter->stats.latecol + - adapter->watchdog_timeouts; + ifp->if_oerrors = + adapter->stats.ecol + adapter->stats.latecol + + adapter->watchdog_events; } - -/********************************************************************** - * - * This routine is called only when em_display_debug_stats is enabled. - * This routine provides a way to take a look at important statistics - * maintained by the driver and hardware. - * - **********************************************************************/ static void em_print_debug_info(struct adapter *adapter) { - device_t dev= adapter->dev; + device_t dev = adapter->dev; uint8_t *hw_addr = adapter->hw.hw_addr; device_printf(dev, "Adapter hardware address = %p \n", hw_addr); - device_printf(dev, "CTRL = 0x%x RCTL = 0x%x\n", - E1000_READ_REG(&adapter->hw, CTRL), - E1000_READ_REG(&adapter->hw, RCTL)); - device_printf(dev, "Packet buffer = Tx=%dk Rx=%dk\n", - ((E1000_READ_REG(&adapter->hw, PBA) & 0xffff0000) >> 16), - (E1000_READ_REG(&adapter->hw, PBA) & 0xffff)); + device_printf(dev, "CTRL = 0x%x RCTL = 0x%x \n", + E1000_READ_REG(&adapter->hw, E1000_CTRL), + E1000_READ_REG(&adapter->hw, E1000_RCTL)); + device_printf(dev, "Packet buffer = Tx=%dk Rx=%dk \n", + ((E1000_READ_REG(&adapter->hw, E1000_PBA) & 0xffff0000) >> 16),\ + (E1000_READ_REG(&adapter->hw, E1000_PBA) & 0xffff) ); device_printf(dev, "Flow control watermarks high = %d low = %d\n", - adapter->hw.fc_high_water, adapter->hw.fc_low_water); + adapter->hw.fc.high_water, + adapter->hw.fc.low_water); device_printf(dev, "tx_int_delay = %d, tx_abs_int_delay = %d\n", - E1000_READ_REG(&adapter->hw, TIDV), - E1000_READ_REG(&adapter->hw, TADV)); + E1000_READ_REG(&adapter->hw, E1000_TIDV), + E1000_READ_REG(&adapter->hw, E1000_TADV)); device_printf(dev, "rx_int_delay = %d, rx_abs_int_delay = %d\n", - E1000_READ_REG(&adapter->hw, RDTR), - E1000_READ_REG(&adapter->hw, RADV)); + E1000_READ_REG(&adapter->hw, E1000_RDTR), + E1000_READ_REG(&adapter->hw, E1000_RADV)); device_printf(dev, "fifo workaround = %lld, fifo_reset_count = %lld\n", - (long long)adapter->tx_fifo_wrk_cnt, - (long long)adapter->tx_fifo_reset_cnt); + (long long)adapter->tx_fifo_wrk_cnt, + (long long)adapter->tx_fifo_reset_cnt); device_printf(dev, "hw tdh = %d, hw tdt = %d\n", - E1000_READ_REG(&adapter->hw, TDH), - E1000_READ_REG(&adapter->hw, TDT)); + E1000_READ_REG(&adapter->hw, E1000_TDH(0)), + E1000_READ_REG(&adapter->hw, E1000_TDT(0))); + device_printf(dev, "hw rdh = %d, hw rdt = %d\n", + E1000_READ_REG(&adapter->hw, E1000_RDH(0)), + E1000_READ_REG(&adapter->hw, E1000_RDT(0))); device_printf(dev, "Num Tx descriptors avail = %d\n", - adapter->num_tx_desc_avail); + adapter->num_tx_desc_avail); device_printf(dev, "Tx Descriptors not avail1 = %ld\n", - adapter->no_tx_desc_avail1); + adapter->no_tx_desc_avail1); device_printf(dev, "Tx Descriptors not avail2 = %ld\n", - adapter->no_tx_desc_avail2); + adapter->no_tx_desc_avail2); device_printf(dev, "Std mbuf failed = %ld\n", - adapter->mbuf_alloc_failed); + adapter->mbuf_alloc_failed); device_printf(dev, "Std mbuf cluster failed = %ld\n", - adapter->mbuf_cluster_failed); + adapter->mbuf_cluster_failed); device_printf(dev, "Driver dropped packets = %ld\n", - adapter->dropped_pkts); + adapter->dropped_pkts); + device_printf(dev, "Driver tx dma failure in encap = %ld\n", + adapter->no_tx_dma_setup); } static void em_print_hw_stats(struct adapter *adapter) { - device_t dev= adapter->dev; + device_t dev = adapter->dev; device_printf(dev, "Excessive collisions = %lld\n", - (long long)adapter->stats.ecol); + (long long)adapter->stats.ecol); +#if (DEBUG_HW > 0) /* Dont output these errors normally */ device_printf(dev, "Symbol errors = %lld\n", - (long long)adapter->stats.symerrs); + (long long)adapter->stats.symerrs); +#endif device_printf(dev, "Sequence errors = %lld\n", - (long long)adapter->stats.sec); + (long long)adapter->stats.sec); device_printf(dev, "Defer count = %lld\n", - (long long)adapter->stats.dc); - + (long long)adapter->stats.dc); device_printf(dev, "Missed Packets = %lld\n", - (long long)adapter->stats.mpc); + (long long)adapter->stats.mpc); device_printf(dev, "Receive No Buffers = %lld\n", - (long long)adapter->stats.rnbc); + (long long)adapter->stats.rnbc); /* RLEC is inaccurate on some hardware, calculate our own. */ - device_printf(dev, "Receive Length errors = %lld\n", - (long long)adapter->stats.roc + - (long long)adapter->stats.ruc); + device_printf(dev, "Receive Length Errors = %lld\n", + ((long long)adapter->stats.roc + (long long)adapter->stats.ruc)); device_printf(dev, "Receive errors = %lld\n", - (long long)adapter->stats.rxerrc); + (long long)adapter->stats.rxerrc); device_printf(dev, "Crc errors = %lld\n", - (long long)adapter->stats.crcerrs); + (long long)adapter->stats.crcerrs); device_printf(dev, "Alignment errors = %lld\n", - (long long)adapter->stats.algnerrc); - device_printf(dev, "Carrier extension errors = %lld\n", - (long long)adapter->stats.cexterr); - device_printf(dev, "RX overruns = %lu\n", adapter->rx_overruns); - device_printf(dev, "Watchdog timeouts = %lu\n", - adapter->watchdog_timeouts); - + (long long)adapter->stats.algnerrc); + device_printf(dev, "Collision/Carrier extension errors = %lld\n", + (long long)adapter->stats.cexterr); + device_printf(dev, "RX overruns = %ld\n", adapter->rx_overruns); + device_printf(dev, "watchdog timeouts = %ld\n", + adapter->watchdog_events); device_printf(dev, "XON Rcvd = %lld\n", - (long long)adapter->stats.xonrxc); + (long long)adapter->stats.xonrxc); device_printf(dev, "XON Xmtd = %lld\n", - (long long)adapter->stats.xontxc); + (long long)adapter->stats.xontxc); device_printf(dev, "XOFF Rcvd = %lld\n", - (long long)adapter->stats.xoffrxc); + (long long)adapter->stats.xoffrxc); device_printf(dev, "XOFF Xmtd = %lld\n", - (long long)adapter->stats.xofftxc); - + (long long)adapter->stats.xofftxc); device_printf(dev, "Good Packets Rcvd = %lld\n", - (long long)adapter->stats.gprc); + (long long)adapter->stats.gprc); device_printf(dev, "Good Packets Xmtd = %lld\n", - (long long)adapter->stats.gptc); + (long long)adapter->stats.gptc); +} + +static void +em_print_nvm_info(struct adapter *adapter) +{ + uint16_t eeprom_data; + int i, j, row = 0; + + /* Its a bit crude, but it gets the job done */ + kprintf("\nInterface EEPROM Dump:\n"); + kprintf("Offset\n0x0000 "); + for (i = 0, j = 0; i < 32; i++, j++) { + if (j == 8) { /* Make the offset block */ + j = 0; ++row; + kprintf("\n0x00%x0 ",row); + } + e1000_read_nvm(&adapter->hw, i, 1, &eeprom_data); + kprintf("%04x ", eeprom_data); + } + kprintf("\n"); } static int em_sysctl_debug_info(SYSCTL_HANDLER_ARGS) { - int error; - int result; struct adapter *adapter; + struct ifnet *ifp; + int error, result; result = -1; error = sysctl_handle_int(oidp, &result, 0, req); - if (error || !req->newptr) return (error); - if (result == 1) { - adapter = (struct adapter *)arg1; + adapter = (struct adapter *)arg1; + ifp = &adapter->arpcom.ac_if; + + lwkt_serialize_enter(ifp->if_serializer); + + if (result == 1) em_print_debug_info(adapter); - } + + /* + * This value will cause a hex dump of the + * first 32 16-bit words of the EEPROM to + * the screen. + */ + if (result == 2) + em_print_nvm_info(adapter); + + lwkt_serialize_exit(ifp->if_serializer); return (error); } @@ -3580,21 +3671,21 @@ em_sysctl_debug_info(SYSCTL_HANDLER_ARGS) static int em_sysctl_stats(SYSCTL_HANDLER_ARGS) { - int error; - int result; - struct adapter *adapter; + int error, result; result = -1; error = sysctl_handle_int(oidp, &result, 0, req); - if (error || !req->newptr) return (error); if (result == 1) { - adapter = (struct adapter *)arg1; + struct adapter *adapter = (struct adapter *)arg1; + struct ifnet *ifp = &adapter->arpcom.ac_if; + + lwkt_serialize_enter(ifp->if_serializer); em_print_hw_stats(adapter); + lwkt_serialize_exit(ifp->if_serializer); } - return (error); } @@ -3603,90 +3694,181 @@ em_sysctl_int_delay(SYSCTL_HANDLER_ARGS) { struct em_int_delay_info *info; struct adapter *adapter; + struct ifnet *ifp; uint32_t regval; - int error; - int usecs; - int ticks; + int error, usecs, ticks; info = (struct em_int_delay_info *)arg1; - adapter = info->adapter; usecs = info->value; error = sysctl_handle_int(oidp, &usecs, 0, req); if (error != 0 || req->newptr == NULL) return (error); - if (usecs < 0 || usecs > E1000_TICKS_TO_USECS(65535)) + if (usecs < 0 || usecs > EM_TICKS_TO_USECS(65535)) return (EINVAL); info->value = usecs; - ticks = E1000_USECS_TO_TICKS(usecs); + ticks = EM_USECS_TO_TICKS(usecs); + + adapter = info->adapter; + ifp = &adapter->arpcom.ac_if; + + lwkt_serialize_enter(ifp->if_serializer); - lwkt_serialize_enter(adapter->interface_data.ac_if.if_serializer); regval = E1000_READ_OFFSET(&adapter->hw, info->offset); regval = (regval & ~0xffff) | (ticks & 0xffff); /* Handle a few special cases. */ switch (info->offset) { case E1000_RDTR: - case E1000_82542_RDTR: - regval |= E1000_RDT_FPDB; break; + case E1000_TIDV: - case E1000_82542_TIDV: if (ticks == 0) { adapter->txd_cmd &= ~E1000_TXD_CMD_IDE; /* Don't write 0 into the TIDV register. */ regval++; - } else + } else { adapter->txd_cmd |= E1000_TXD_CMD_IDE; + } break; } E1000_WRITE_OFFSET(&adapter->hw, info->offset, regval); - lwkt_serialize_exit(adapter->interface_data.ac_if.if_serializer); + + lwkt_serialize_exit(ifp->if_serializer); return (0); } static void em_add_int_delay_sysctl(struct adapter *adapter, const char *name, - const char *description, struct em_int_delay_info *info, - int offset, int value) + const char *description, struct em_int_delay_info *info, + int offset, int value) { info->adapter = adapter; info->offset = offset; info->value = value; - SYSCTL_ADD_PROC(&adapter->sysctl_ctx, - SYSCTL_CHILDREN(adapter->sysctl_tree), - OID_AUTO, name, CTLTYPE_INT|CTLFLAG_RW, - info, 0, em_sysctl_int_delay, "I", description); + + if (adapter->sysctl_tree != NULL) { + SYSCTL_ADD_PROC(&adapter->sysctl_ctx, + SYSCTL_CHILDREN(adapter->sysctl_tree), + OID_AUTO, name, CTLTYPE_INT|CTLFLAG_RW, + info, 0, em_sysctl_int_delay, "I", description); + } +} + +static void +em_add_sysctl(struct adapter *adapter) +{ +#ifdef PROFILE_SERIALIZER + struct ifnet *ifp = &adapter->arpcom.ac_if; +#endif + + sysctl_ctx_init(&adapter->sysctl_ctx); + adapter->sysctl_tree = SYSCTL_ADD_NODE(&adapter->sysctl_ctx, + SYSCTL_STATIC_CHILDREN(_hw), OID_AUTO, + device_get_nameunit(adapter->dev), + CTLFLAG_RD, 0, ""); + if (adapter->sysctl_tree == NULL) { + device_printf(adapter->dev, "can't add sysctl node\n"); + } else { + SYSCTL_ADD_PROC(&adapter->sysctl_ctx, + SYSCTL_CHILDREN(adapter->sysctl_tree), + OID_AUTO, "debug", CTLTYPE_INT|CTLFLAG_RW, adapter, 0, + em_sysctl_debug_info, "I", "Debug Information"); + + SYSCTL_ADD_PROC(&adapter->sysctl_ctx, + SYSCTL_CHILDREN(adapter->sysctl_tree), + OID_AUTO, "stats", CTLTYPE_INT|CTLFLAG_RW, adapter, 0, + em_sysctl_stats, "I", "Statistics"); + + SYSCTL_ADD_INT(&adapter->sysctl_ctx, + SYSCTL_CHILDREN(adapter->sysctl_tree), + OID_AUTO, "rxd", CTLFLAG_RD, + &adapter->num_rx_desc, 0, NULL); + SYSCTL_ADD_INT(&adapter->sysctl_ctx, + SYSCTL_CHILDREN(adapter->sysctl_tree), + OID_AUTO, "txd", CTLFLAG_RD, + &adapter->num_tx_desc, 0, NULL); + +#ifdef PROFILE_SERIALIZER + SYSCTL_ADD_UINT(&adapter->sysctl_ctx, + SYSCTL_CHILDREN(adapter->sysctl_tree), + OID_AUTO, "serializer_sleep", CTLFLAG_RW, + &ifp->if_serializer->sleep_cnt, 0, NULL); + SYSCTL_ADD_UINT(&adapter->sysctl_ctx, + SYSCTL_CHILDREN(adapter->sysctl_tree), + OID_AUTO, "serializer_tryfail", CTLFLAG_RW, + &ifp->if_serializer->tryfail_cnt, 0, NULL); + SYSCTL_ADD_UINT(&adapter->sysctl_ctx, + SYSCTL_CHILDREN(adapter->sysctl_tree), + OID_AUTO, "serializer_enter", CTLFLAG_RW, + &ifp->if_serializer->enter_cnt, 0, NULL); + SYSCTL_ADD_UINT(&adapter->sysctl_ctx, + SYSCTL_CHILDREN(adapter->sysctl_tree), + OID_AUTO, "serializer_try", CTLFLAG_RW, + &ifp->if_serializer->try_cnt, 0, NULL); +#endif + if (adapter->hw.mac.type >= e1000_82540) { + SYSCTL_ADD_PROC(&adapter->sysctl_ctx, + SYSCTL_CHILDREN(adapter->sysctl_tree), + OID_AUTO, "int_throttle_ceil", + CTLTYPE_INT|CTLFLAG_RW, adapter, 0, + em_sysctl_int_throttle, "I", + "interrupt throttling rate"); + } + } + + /* Set up some sysctls for the tunable interrupt delays */ + em_add_int_delay_sysctl(adapter, "rx_int_delay", + "receive interrupt delay in usecs", &adapter->rx_int_delay, + E1000_REGISTER(&adapter->hw, E1000_RDTR), em_rx_int_delay_dflt); + em_add_int_delay_sysctl(adapter, "tx_int_delay", + "transmit interrupt delay in usecs", &adapter->tx_int_delay, + E1000_REGISTER(&adapter->hw, E1000_TIDV), em_tx_int_delay_dflt); + if (adapter->hw.mac.type >= e1000_82540) { + em_add_int_delay_sysctl(adapter, "rx_abs_int_delay", + "receive interrupt delay limit in usecs", + &adapter->rx_abs_int_delay, + E1000_REGISTER(&adapter->hw, E1000_RADV), + em_rx_abs_int_delay_dflt); + em_add_int_delay_sysctl(adapter, "tx_abs_int_delay", + "transmit interrupt delay limit in usecs", + &adapter->tx_abs_int_delay, + E1000_REGISTER(&adapter->hw, E1000_TADV), + em_tx_abs_int_delay_dflt); + } } static int em_sysctl_int_throttle(SYSCTL_HANDLER_ARGS) { struct adapter *adapter = (void *)arg1; - int error; - int throttle; + struct ifnet *ifp = &adapter->arpcom.ac_if; + int error, throttle; - throttle = em_int_throttle_ceil; + throttle = adapter->int_throttle_ceil; error = sysctl_handle_int(oidp, &throttle, 0, req); if (error || req->newptr == NULL) return error; if (throttle < 0 || throttle > 1000000000 / 256) return EINVAL; + + lwkt_serialize_enter(ifp->if_serializer); + if (throttle) { /* * Set the interrupt throttling rate in 256ns increments, * recalculate sysctl value assignment to get exact frequency. */ throttle = 1000000000 / 256 / throttle; - lwkt_serialize_enter(adapter->interface_data.ac_if.if_serializer); - em_int_throttle_ceil = 1000000000 / 256 / throttle; - E1000_WRITE_REG(&adapter->hw, ITR, throttle); - lwkt_serialize_exit(adapter->interface_data.ac_if.if_serializer); + adapter->int_throttle_ceil = 1000000000 / 256 / throttle; } else { - lwkt_serialize_enter(adapter->interface_data.ac_if.if_serializer); - em_int_throttle_ceil = 0; - E1000_WRITE_REG(&adapter->hw, ITR, 0); - lwkt_serialize_exit(adapter->interface_data.ac_if.if_serializer); + adapter->int_throttle_ceil = 0; + } + E1000_WRITE_REG(&adapter->hw, E1000_ITR, throttle); + + lwkt_serialize_exit(ifp->if_serializer); + + if (bootverbose) { + if_printf(ifp, "Interrupt moderation set to %d/sec\n", + adapter->int_throttle_ceil); } - device_printf(adapter->dev, "Interrupt moderation set to %d/sec\n", - em_int_throttle_ceil); return 0; } diff --git a/sys/dev/netif/em/if_em.h b/sys/dev/netif/em/if_em.h index 808de75fcb..3ac30a8495 100644 --- a/sys/dev/netif/em/if_em.h +++ b/sys/dev/netif/em/if_em.h @@ -1,41 +1,36 @@ -/************************************************************************** - -Copyright (c) 2001-2006, Intel Corporation -All rights reserved. - -Redistribution and use in source and binary forms, with or without -modification, are permitted provided that the following conditions are met: - - 1. Redistributions of source code must retain the above copyright notice, - this list of conditions and the following disclaimer. - - 2. Redistributions in binary form must reproduce the above copyright - notice, this list of conditions and the following disclaimer in the - documentation and/or other materials provided with the distribution. - - 3. Neither the name of the Intel Corporation nor the names of its - contributors may be used to endorse or promote products derived from - this software without specific prior written permission. - -THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" -AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE -IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE -ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE -LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR -CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF -SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS -INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN -CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) -ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE -POSSIBILITY OF SUCH DAMAGE. - -***************************************************************************/ - -/*$FreeBSD: src/sys/dev/em/if_em.h,v 1.1.2.13 2003/06/09 21:43:41 pdeuskar Exp $*/ -/*$DragonFly: src/sys/dev/netif/em/if_em.h,v 1.20 2008/07/22 12:08:41 sephe Exp $*/ +/* + * Copyright (c) 2001-2008, Intel Corporation + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions are met: + * + * 1. Redistributions of source code must retain the above copyright notice, + * this list of conditions and the following disclaimer. + * + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in the + * documentation and/or other materials provided with the distribution. + * + * 3. Neither the name of the Intel Corporation nor the names of its + * contributors may be used to endorse or promote products derived from + * this software without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE + * ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE + * LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR + * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF + * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS + * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN + * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) + * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGE. + */ -#ifndef _EM_H_DEFINED_ -#define _EM_H_DEFINED_ +#ifndef _IF_EM_H_ +#define _IF_EM_H_ /* Tunables */ @@ -49,12 +44,12 @@ POSSIBILITY OF SUCH DAMAGE. * descriptor is 16 bytes. * Since TDLEN should be multiple of 128bytes, the number of transmit * desscriptors should meet the following condition. - * (num_tx_desc * sizeof(struct em_tx_desc)) % 128 == 0 + * (num_tx_desc * sizeof(struct e1000_tx_desc)) % 128 == 0 */ -#define EM_MIN_TXD 80 -#define EM_MAX_TXD_82543 256 -#define EM_MAX_TXD 4096 -#define EM_DEFAULT_TXD EM_MAX_TXD_82543 +#define EM_MIN_TXD 80 +#define EM_MAX_TXD_82543 256 +#define EM_MAX_TXD 4096 +#define EM_DEFAULT_TXD EM_MAX_TXD_82543 /* * EM_RXD - Maximum number of receive Descriptors @@ -67,12 +62,12 @@ POSSIBILITY OF SUCH DAMAGE. * descriptor. The maximum MTU size is 16110. * Since TDLEN should be multiple of 128bytes, the number of transmit * desscriptors should meet the following condition. - * (num_tx_desc * sizeof(struct em_tx_desc)) % 128 == 0 + * (num_tx_desc * sizeof(struct e1000_tx_desc)) % 128 == 0 */ -#define EM_MIN_RXD 80 -#define EM_MAX_RXD_82543 256 -#define EM_MAX_RXD 4096 -#define EM_DEFAULT_RXD EM_MAX_RXD_82543 +#define EM_MIN_RXD 80 +#define EM_MAX_RXD_82543 256 +#define EM_MAX_RXD 4096 +#define EM_DEFAULT_RXD EM_MAX_RXD_82543 /* * EM_TIDV - Transmit Interrupt Delay Value @@ -84,7 +79,7 @@ POSSIBILITY OF SUCH DAMAGE. * system is reporting dropped transmits, this value may be set too high * causing the driver to run out of available transmit descriptors. */ -#define EM_TIDV 64 +#define EM_TIDV 64 /* * EM_TADV - Transmit Absolute Interrupt Delay Value @@ -98,7 +93,7 @@ POSSIBILITY OF SUCH DAMAGE. * along with EM_TIDV, may improve traffic throughput in specific * network conditions. */ -#define EM_TADV 64 +#define EM_TADV 64 /* * EM_RDTR - Receive Interrupt Delay Timer (Packet Timer) @@ -119,7 +114,7 @@ POSSIBILITY OF SUCH DAMAGE. * restoring the network connection. To eliminate the potential * for the hang ensure that EM_RDTR is set to 0. */ -#define EM_RDTR 0 +#define EM_RDTR 0 /* * Receive Interrupt Absolute Delay Timer (Not valid for 82542/82543/82544) @@ -132,30 +127,35 @@ POSSIBILITY OF SUCH DAMAGE. * along with EM_RDTR, may improve traffic throughput in specific network * conditions. */ -#define EM_RADV 64 - -/* - * Inform the stack about transmit checksum offload capabilities. - */ -#define EM_CHECKSUM_FEATURES (CSUM_TCP | CSUM_UDP) +#define EM_RADV 64 /* * This parameter controls the duration of transmit watchdog timer. */ -#define EM_TX_TIMEOUT 5 /* set to 5 seconds */ +#define EM_TX_TIMEOUT 5 + +/* One for TX csum offloading desc, the other is reserved */ +#define EM_TX_RESERVED 2 + +/* Large enough for 16K jumbo frame */ +#define EM_TX_SPARE 8 + +/* Interrupt throttle rate */ +#define EM_DEFAULT_ITR 10000 /* * This parameter controls when the driver calls the routine to reclaim * transmit descriptors. */ #define EM_TX_CLEANUP_THRESHOLD (adapter->num_tx_desc / 8) +#define EM_TX_OP_THRESHOLD (adapter->num_tx_desc / 32) /* * This parameter controls whether or not autonegotation is enabled. * 0 - Disable autonegotiation * 1 - Enable autonegotiation */ -#define DO_AUTO_NEG 1 +#define DO_AUTO_NEG 1 /* * This parameter control whether or not the driver will wait for @@ -163,38 +163,39 @@ POSSIBILITY OF SUCH DAMAGE. * 1 - Wait for autonegotiation to complete * 0 - Don't wait for autonegotiation to complete */ -#define WAIT_FOR_AUTO_NEG_DEFAULT 0 - -/* - * EM_MASTER_SLAVE is only defined to enable a workaround for a known - * compatibility issue with 82541/82547 devices and some switches. - * See the "Known Limitations" section of the README file for a complete - * description and a list of affected switches. - * - * 0 = Hardware default - * 1 = Master mode - * 2 = Slave mode - * 3 = Auto master/slave - */ -/* #define EM_MASTER_SLAVE 2 */ +#define WAIT_FOR_AUTO_NEG_DEFAULT 0 /* Tunables -- End */ -#define AUTONEG_ADV_DEFAULT (ADVERTISE_10_HALF | ADVERTISE_10_FULL | \ - ADVERTISE_100_HALF | ADVERTISE_100_FULL | \ - ADVERTISE_1000_FULL) +#define AUTONEG_ADV_DEFAULT (ADVERTISE_10_HALF | \ + ADVERTISE_10_FULL | \ + ADVERTISE_100_HALF | \ + ADVERTISE_100_FULL | \ + ADVERTISE_1000_FULL) -#define EM_VENDOR_ID 0x8086 -#define EM_FLASH 0x0014 /* Flash memory on ICH8 */ +#define AUTO_ALL_MODES 0 -#define EM_JUMBO_PBA 0x00000028 -#define EM_DEFAULT_PBA 0x00000030 -#define EM_SMARTSPEED_DOWNSHIFT 3 -#define EM_SMARTSPEED_MAX 15 +/* PHY master/slave setting */ +#define EM_MASTER_SLAVE e1000_ms_hw_default -#define MAX_NUM_MULTICAST_ADDRESSES 128 -#define PCI_ANY_ID (~0U) +/* + * Micellaneous constants + */ +#define EM_VENDOR_ID 0x8086 +#define EM_BAR_MEM PCIR_BAR(0) +#define EM_BAR_FLASH PCIR_BAR(1) + +#define EM_JUMBO_PBA 0x00000028 +#define EM_DEFAULT_PBA 0x00000030 +#define EM_SMARTSPEED_DOWNSHIFT 3 +#define EM_SMARTSPEED_MAX 15 +#define EM_MAX_INTR 10 + +#define MAX_NUM_MULTICAST_ADDRESSES 128 +#define PCI_ANY_ID (~0U) +#define EM_FC_PAUSE_TIME 1000 +#define EM_EEPROM_APME 0x400; /* * TDBA/RDBA should be aligned on 16 byte boundary. But TDLEN/RDLEN should be @@ -203,7 +204,7 @@ POSSIBILITY OF SUCH DAMAGE. */ #define EM_DBA_ALIGN 128 -#define SPEED_MODE_BIT (1 << 21) /* On PCI-E MACs only */ +#define SPEED_MODE_BIT (1 << 21) /* On PCI-E MACs only */ /* PCI Config defines */ #define EM_BAR_TYPE(v) ((v) & EM_BAR_TYPE_MASK) @@ -215,135 +216,94 @@ POSSIBILITY OF SUCH DAMAGE. #define EM_BAR_MEM_TYPE_32BIT 0x00000000 #define EM_BAR_MEM_TYPE_64BIT 0x00000004 +#define EM_MAX_SCATTER 64 +#define EM_TSO_SIZE (65535 + \ + sizeof(struct ether_vlan_header)) +#define EM_MAX_SEGSIZE 4096 +#define EM_MSIX_MASK 0x01F00000 /* For 82574 use */ +#define ETH_ZLEN 60 + +#define EM_CSUM_FEATURES (CSUM_IP | CSUM_TCP | CSUM_UDP) +#define CSUM_OFFLOAD (CSUM_IP | CSUM_TCP | CSUM_UDP) + /* - * Community introduced backward - * compatibility issue. + * 82574 has a nonstandard address for EIAC + * and since its only used in MSIX, and in + * the em driver only 82574 uses MSIX we can + * solve it just using this define. */ -#if !defined(PCIR_CIS) -#define PCIR_CIS PCIR_CARDBUSCIS -#endif - -/* Defines for printing debug information */ -#define DEBUG_INIT 0 -#define DEBUG_IOCTL 0 -#define DEBUG_HW 0 - -#define INIT_DEBUGOUT(S) if (DEBUG_INIT) kprintf(S "\n") -#define INIT_DEBUGOUT1(S, A) if (DEBUG_INIT) kprintf(S "\n", A) -#define INIT_DEBUGOUT2(S, A, B) if (DEBUG_INIT) kprintf(S "\n", A, B) -#define IOCTL_DEBUGOUT(S) if (DEBUG_IOCTL) kprintf(S "\n") -#define IOCTL_DEBUGOUT1(S, A) if (DEBUG_IOCTL) kprintf(S "\n", A) -#define IOCTL_DEBUGOUT2(S, A, B) if (DEBUG_IOCTL) kprintf(S "\n", A, B) -#define HW_DEBUGOUT(S) if (DEBUG_HW) kprintf(S "\n") -#define HW_DEBUGOUT1(S, A) if (DEBUG_HW) kprintf(S "\n", A) -#define HW_DEBUGOUT2(S, A, B) if (DEBUG_HW) kprintf(S "\n", A, B) - - -/* Supported RX Buffer Sizes */ -#define EM_RXBUFFER_2048 2048 -#define EM_RXBUFFER_4096 4096 -#define EM_RXBUFFER_8192 8192 -#define EM_RXBUFFER_16384 16384 - -#define EM_MAX_SCATTER 64 - -/* ****************************************************************************** - * vendor_info_array - * - * This array contains the list of Subvendor/Subdevice IDs on which the driver - * should load. - * - * ******************************************************************************/ -typedef struct _em_vendor_info_t { - unsigned int vendor_id; - unsigned int device_id; - unsigned int subvendor_id; - unsigned int subdevice_id; - unsigned int index; -} em_vendor_info_t; +#define EM_EIAC 0x000DC +/* Used in for 82547 10Mb Half workaround */ +#define EM_PBA_BYTES_SHIFT 0xA +#define EM_TX_HEAD_ADDR_SHIFT 7 +#define EM_PBA_TX_MASK 0xFFFF0000 +#define EM_FIFO_HDR 0x10 +#define EM_82547_PKT_THRESH 0x3e0 -struct em_buffer { - int next_eop; /* Index of the desc to watch */ - struct mbuf *m_head; - bus_dmamap_t map; /* bus_dma map for packet */ -}; +struct adapter; -struct em_q { - int nsegs; /* # of segments/descriptors */ - bus_dma_segment_t segs[EM_MAX_SCATTER]; +struct em_int_delay_info { + struct adapter *adapter; /* Back-pointer to the adapter struct */ + int offset; /* Register offset to read/write */ + int value; /* Current value in usecs */ }; /* * Bus dma allocation structure used by - * em_dma_malloc and em_dma_free. + * e1000_dma_malloc and e1000_dma_free. */ struct em_dma_alloc { bus_addr_t dma_paddr; - caddr_t dma_vaddr; + void *dma_vaddr; bus_dma_tag_t dma_tag; bus_dmamap_t dma_map; - bus_dma_segment_t dma_seg; - int dma_nseg; }; -typedef enum _XSUM_CONTEXT_T { - OFFLOAD_NONE, - OFFLOAD_TCP_IP, - OFFLOAD_UDP_IP -} XSUM_CONTEXT_T; +/* Our adapter structure */ +struct adapter { + struct arpcom arpcom; + struct e1000_hw hw; -struct adapter; -struct em_int_delay_info { - struct adapter *adapter; /* Back-pointer to the adapter struct */ - int offset; /* Register offset to read/write */ - int value; /* Current value in usecs */ -}; + /* DragonFly operating-system-specific structures. */ + struct e1000_osdep osdep; + device_t dev; -/* For 82544 PCIX Workaround */ -typedef struct _ADDRESS_LENGTH_PAIR -{ - uint64_t address; - uint32_t length; -} ADDRESS_LENGTH_PAIR, *PADDRESS_LENGTH_PAIR; + bus_dma_tag_t parent_dtag; -typedef struct _DESCRIPTOR_PAIR -{ - ADDRESS_LENGTH_PAIR descriptor[4]; - uint32_t elements; -} DESC_ARRAY, *PDESC_ARRAY; + struct resource *memory; + int memory_rid; + struct resource *flash; + int flash_rid; -/* Our adapter structure */ -struct adapter { - struct arpcom interface_data; - struct em_hw hw; - - /* Operating-system-specific structures */ - struct em_osdep osdep; - struct device *dev; - struct resource *res_memory; - struct resource *flash_mem; - struct resource *res_ioport; - struct resource *res_interrupt; - void *int_handler_tag; - struct ifmedia media; - struct callout timer; - struct callout tx_fifo_timer; - int if_flags; - int io_rid; + struct resource *ioport; + int io_rid; + + struct resource *intr_res; + void *intr_tag; + int intr_rid; + + struct ifmedia media; + struct callout timer; + struct callout tx_fifo_timer; + int if_flags; + int max_frame_size; + int min_frame_size; + + /* Management and WOL features */ + int wol; + int has_manage; /* Info about the board itself */ - uint32_t part_num; - uint8_t link_active; - uint16_t link_speed; - uint16_t link_duplex; - uint32_t smartspeed; + uint8_t link_active; + uint16_t link_speed; + uint16_t link_duplex; + uint32_t smartspeed; struct em_int_delay_info tx_int_delay; struct em_int_delay_info tx_abs_int_delay; struct em_int_delay_info rx_int_delay; struct em_int_delay_info rx_abs_int_delay; - - XSUM_CONTEXT_T active_checksum_context; + int int_throttle_ceil; /* * Transmit definitions @@ -355,14 +315,15 @@ struct adapter { * The number of remaining tx_desc is num_tx_desc_avail. */ struct em_dma_alloc txdma; /* bus_dma glue for tx desc */ - struct em_tx_desc *tx_desc_base; + struct e1000_tx_desc *tx_desc_base; uint32_t next_avail_tx_desc; uint32_t next_tx_to_clean; - volatile uint16_t num_tx_desc_avail; - uint16_t num_tx_desc; + int num_tx_desc_avail; + int num_tx_desc; uint32_t txd_cmd; struct em_buffer *tx_buffer_area; bus_dma_tag_t txtag; /* dma tag for tx */ + int spare_tx_desc; /* * Receive definitions @@ -373,12 +334,13 @@ struct adapter { * The next pair to check on receive is at offset next_rx_desc_to_check */ struct em_dma_alloc rxdma; /* bus_dma glue for rx desc */ - struct em_rx_desc *rx_desc_base; + struct e1000_rx_desc *rx_desc_base; uint32_t next_rx_desc_to_check; - uint16_t num_rx_desc; uint32_t rx_buffer_len; + int num_rx_desc; struct em_buffer *rx_buffer_area; bus_dma_tag_t rxtag; + bus_dmamap_t rx_sparemap; /* * First/last mbuf pointers, for @@ -387,40 +349,64 @@ struct adapter { struct mbuf *fmp; struct mbuf *lmp; + /* Misc stats maintained by the driver */ + unsigned long dropped_pkts; + unsigned long mbuf_alloc_failed; + unsigned long mbuf_cluster_failed; + unsigned long no_tx_desc_avail1; + unsigned long no_tx_desc_avail2; + unsigned long no_tx_map_avail; + unsigned long no_tx_dma_setup; + unsigned long watchdog_events; + unsigned long rx_overruns; + unsigned long rx_irq; + unsigned long tx_irq; + unsigned long link_irq; + + /* sysctl tree glue */ struct sysctl_ctx_list sysctl_ctx; struct sysctl_oid *sysctl_tree; - /* Misc stats maintained by the driver */ - unsigned long dropped_pkts; - unsigned long mbuf_alloc_failed; - unsigned long mbuf_cluster_failed; - unsigned long no_tx_desc_avail1; - unsigned long no_tx_desc_avail2; - unsigned long no_tx_map_avail; - unsigned long no_tx_dma_setup; - unsigned long rx_overruns; - unsigned long watchdog_timeouts; - - /* Used in for 82547 10Mb Half workaround */ - uint32_t tx_fifo_size; - uint32_t tx_fifo_head; - uint32_t tx_fifo_head_addr; - uint64_t tx_fifo_reset_cnt; - uint64_t tx_fifo_wrk_cnt; - uint32_t tx_head_addr; - -#define EM_PBA_BYTES_SHIFT 0xA -#define EM_TX_HEAD_ADDR_SHIFT 7 -#define EM_PBA_TX_MASK 0xFFFF0000 -#define EM_FIFO_HDR 0x10 - -#define EM_82547_PKT_THRESH 0x3e0 - - /* For 82544 PCIX Workaround */ - boolean_t pcix_82544; - boolean_t in_detach; - - struct em_hw_stats stats; + /* 82547 workaround */ + uint32_t tx_fifo_size; + uint32_t tx_fifo_head; + uint32_t tx_fifo_head_addr; + uint64_t tx_fifo_reset_cnt; + uint64_t tx_fifo_wrk_cnt; + uint32_t tx_head_addr; + + /* For 82544 PCIX Workaround */ + boolean_t pcix_82544; + boolean_t in_detach; + + struct e1000_hw_stats stats; +}; + +struct em_vendor_info { + uint16_t vendor_id; + uint16_t device_id; + const char *desc; +}; + +struct em_buffer { + int next_eop; /* Index of the desc to watch */ + struct mbuf *m_head; + bus_dmamap_t map; /* bus_dma map for packet */ }; -#endif /* !_EM_H_DEFINED_ */ +/* For 82544 PCIX Workaround */ +typedef struct _ADDRESS_LENGTH_PAIR { + uint64_t address; + uint32_t length; +} ADDRESS_LENGTH_PAIR, *PADDRESS_LENGTH_PAIR; + +typedef struct _DESCRIPTOR_PAIR { + ADDRESS_LENGTH_PAIR descriptor[4]; + uint32_t elements; +} DESC_ARRAY, *PDESC_ARRAY; + +#define EM_IS_OACTIVE(adapter) \ + ((adapter)->num_tx_desc_avail < \ + (adapter)->spare_tx_desc + EM_TX_RESERVED) + +#endif /* _IF_EM_H_ */ diff --git a/sys/dev/netif/em/if_em_hw.c b/sys/dev/netif/em/if_em_hw.c deleted file mode 100644 index 6d78d300a7..0000000000 --- a/sys/dev/netif/em/if_em_hw.c +++ /dev/null @@ -1,9197 +0,0 @@ -/******************************************************************************* -Copyright (c) 2001-2005, Intel Corporation -All rights reserved. - -Redistribution and use in source and binary forms, with or without -modification, are permitted provided that the following conditions are met: - - 1. Redistributions of source code must retain the above copyright notice, - this list of conditions and the following disclaimer. - - 2. Redistributions in binary form must reproduce the above copyright - notice, this list of conditions and the following disclaimer in the - documentation and/or other materials provided with the distribution. - - 3. Neither the name of the Intel Corporation nor the names of its - contributors may be used to endorse or promote products derived from - this software without specific prior written permission. - -THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" -AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE -IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE -ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE -LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR -CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF -SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS -INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN -CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) -ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE -POSSIBILITY OF SUCH DAMAGE. -*******************************************************************************/ - -/*$FreeBSD: src/sys/dev/em/if_em_hw.c,v 1.1.2.8 2003/06/09 21:43:41 pdeuskar Exp $*/ -/*$DragonFly: src/sys/dev/netif/em/if_em_hw.c,v 1.13 2008/01/11 10:34:15 sephe Exp $*/ - -/* if_em_hw.c - * Shared functions for accessing and configuring the MAC - */ - -#define STATIC static - -#ifdef LM -#include "if_em_hw.h" -#else -#include -#endif - -static int32_t em_swfw_sync_acquire(struct em_hw *hw, uint16_t mask); -static void em_swfw_sync_release(struct em_hw *hw, uint16_t mask); -static int32_t em_read_kmrn_reg(struct em_hw *hw, uint32_t reg_addr, uint16_t *data); -static int32_t em_write_kmrn_reg(struct em_hw *hw, uint32_t reg_addr, uint16_t data); -static int32_t em_get_software_semaphore(struct em_hw *hw); -static void em_release_software_semaphore(struct em_hw *hw); - -static uint8_t em_arc_subsystem_valid(struct em_hw *hw); -static int32_t em_check_downshift(struct em_hw *hw); -static int32_t em_check_polarity(struct em_hw *hw, em_rev_polarity *polarity); -static void em_clear_vfta(struct em_hw *hw); -static int32_t em_commit_shadow_ram(struct em_hw *hw); -static int32_t em_config_dsp_after_link_change(struct em_hw *hw, boolean_t link_up); -static int32_t em_config_fc_after_link_up(struct em_hw *hw); -static int32_t em_detect_gig_phy(struct em_hw *hw); -static int32_t em_erase_ich8_4k_segment(struct em_hw *hw, uint32_t bank); -static int32_t em_get_auto_rd_done(struct em_hw *hw); -static int32_t em_get_cable_length(struct em_hw *hw, uint16_t *min_length, uint16_t *max_length); -static int32_t em_get_hw_eeprom_semaphore(struct em_hw *hw); -static int32_t em_get_phy_cfg_done(struct em_hw *hw); -static int32_t em_get_software_flag(struct em_hw *hw); -static int32_t em_ich8_cycle_init(struct em_hw *hw); -static int32_t em_ich8_flash_cycle(struct em_hw *hw, uint32_t timeout); -static int32_t em_id_led_init(struct em_hw *hw); -static int32_t em_init_lcd_from_nvm_config_region(struct em_hw *hw, uint32_t cnf_base_addr, uint32_t cnf_size); -static int32_t em_init_lcd_from_nvm(struct em_hw *hw); -static void em_init_rx_addrs(struct em_hw *hw); -static void em_initialize_hardware_bits(struct em_hw *hw); -static boolean_t em_is_onboard_nvm_eeprom(struct em_hw *hw); -static int32_t em_kumeran_lock_loss_workaround(struct em_hw *hw); -static int32_t em_mng_enable_host_if(struct em_hw *hw); -static int32_t em_mng_host_if_write(struct em_hw *hw, uint8_t *buffer, uint16_t length, uint16_t offset, uint8_t *sum); -static int32_t em_mng_write_cmd_header(struct em_hw* hw, struct em_host_mng_command_header* hdr); -static int32_t em_mng_write_commit(struct em_hw *hw); -static int32_t em_phy_ife_get_info(struct em_hw *hw, struct em_phy_info *phy_info); -static int32_t em_phy_igp_get_info(struct em_hw *hw, struct em_phy_info *phy_info); -static int32_t em_read_eeprom_eerd(struct em_hw *hw, uint16_t offset, uint16_t words, uint16_t *data); -static int32_t em_write_eeprom_eewr(struct em_hw *hw, uint16_t offset, uint16_t words, uint16_t *data); -static int32_t em_poll_eerd_eewr_done(struct em_hw *hw, int eerd); -static int32_t em_phy_m88_get_info(struct em_hw *hw, struct em_phy_info *phy_info); -static void em_put_hw_eeprom_semaphore(struct em_hw *hw); -static int32_t em_read_ich8_byte(struct em_hw *hw, uint32_t index, uint8_t *data); -static int32_t em_verify_write_ich8_byte(struct em_hw *hw, uint32_t index, uint8_t byte); -static int32_t em_write_ich8_byte(struct em_hw *hw, uint32_t index, uint8_t byte); -static int32_t em_read_ich8_word(struct em_hw *hw, uint32_t index, uint16_t *data); -static int32_t em_read_ich8_data(struct em_hw *hw, uint32_t index, uint32_t size, uint16_t *data); -static int32_t em_write_ich8_data(struct em_hw *hw, uint32_t index, uint32_t size, uint16_t data); -static int32_t em_read_eeprom_ich8(struct em_hw *hw, uint16_t offset, uint16_t words, uint16_t *data); -static int32_t em_write_eeprom_ich8(struct em_hw *hw, uint16_t offset, uint16_t words, uint16_t *data); -static void em_release_software_flag(struct em_hw *hw); -static int32_t em_set_d3_lplu_state(struct em_hw *hw, boolean_t active); -static int32_t em_set_d0_lplu_state(struct em_hw *hw, boolean_t active); -static int32_t em_set_pci_ex_no_snoop(struct em_hw *hw, uint32_t no_snoop); -static void em_set_pci_express_master_disable(struct em_hw *hw); -static int32_t em_wait_autoneg(struct em_hw *hw); -static void em_write_reg_io(struct em_hw *hw, uint32_t offset, uint32_t value); -static int32_t em_set_phy_type(struct em_hw *hw); -static void em_phy_init_script(struct em_hw *hw); -static int32_t em_setup_copper_link(struct em_hw *hw); -static int32_t em_setup_fiber_serdes_link(struct em_hw *hw); -static int32_t em_adjust_serdes_amplitude(struct em_hw *hw); -static int32_t em_phy_force_speed_duplex(struct em_hw *hw); -static int32_t em_config_mac_to_phy(struct em_hw *hw); -static void em_raise_mdi_clk(struct em_hw *hw, uint32_t *ctrl); -static void em_lower_mdi_clk(struct em_hw *hw, uint32_t *ctrl); -static void em_shift_out_mdi_bits(struct em_hw *hw, uint32_t data, - uint16_t count); -static uint16_t em_shift_in_mdi_bits(struct em_hw *hw); -static int32_t em_phy_reset_dsp(struct em_hw *hw); -static int32_t em_write_eeprom_spi(struct em_hw *hw, uint16_t offset, - uint16_t words, uint16_t *data); -static int32_t em_write_eeprom_microwire(struct em_hw *hw, - uint16_t offset, uint16_t words, - uint16_t *data); -static int32_t em_spi_eeprom_ready(struct em_hw *hw); -static void em_raise_ee_clk(struct em_hw *hw, uint32_t *eecd); -static void em_lower_ee_clk(struct em_hw *hw, uint32_t *eecd); -static void em_shift_out_ee_bits(struct em_hw *hw, uint16_t data, - uint16_t count); -static int32_t em_write_phy_reg_ex(struct em_hw *hw, uint32_t reg_addr, - uint16_t phy_data); -static int32_t em_read_phy_reg_ex(struct em_hw *hw,uint32_t reg_addr, - uint16_t *phy_data); -static uint16_t em_shift_in_ee_bits(struct em_hw *hw, uint16_t count); -static int32_t em_acquire_eeprom(struct em_hw *hw); -static void em_release_eeprom(struct em_hw *hw); -static void em_standby_eeprom(struct em_hw *hw); -static int32_t em_set_vco_speed(struct em_hw *hw); -static int32_t em_polarity_reversal_workaround(struct em_hw *hw); -static int32_t em_set_phy_mode(struct em_hw *hw); -static int32_t em_host_if_read_cookie(struct em_hw *hw, uint8_t *buffer); -static uint8_t em_calculate_mng_checksum(char *buffer, uint32_t length); -static int32_t em_configure_kmrn_for_10_100(struct em_hw *hw, - uint16_t duplex); -static int32_t em_configure_kmrn_for_1000(struct em_hw *hw); - -/* IGP cable length table */ -static const -uint16_t em_igp_cable_length_table[IGP01E1000_AGC_LENGTH_TABLE_SIZE] = - { 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, - 5, 10, 10, 10, 10, 10, 10, 10, 20, 20, 20, 20, 20, 25, 25, 25, - 25, 25, 25, 25, 30, 30, 30, 30, 40, 40, 40, 40, 40, 40, 40, 40, - 40, 50, 50, 50, 50, 50, 50, 50, 60, 60, 60, 60, 60, 60, 60, 60, - 60, 70, 70, 70, 70, 70, 70, 80, 80, 80, 80, 80, 80, 90, 90, 90, - 90, 90, 90, 90, 90, 90, 100, 100, 100, 100, 100, 100, 100, 100, 100, 100, - 100, 100, 100, 100, 110, 110, 110, 110, 110, 110, 110, 110, 110, 110, 110, 110, - 110, 110, 110, 110, 110, 110, 120, 120, 120, 120, 120, 120, 120, 120, 120, 120}; - -static const -uint16_t em_igp_2_cable_length_table[IGP02E1000_AGC_LENGTH_TABLE_SIZE] = - { 0, 0, 0, 0, 0, 0, 0, 0, 3, 5, 8, 11, 13, 16, 18, 21, - 0, 0, 0, 3, 6, 10, 13, 16, 19, 23, 26, 29, 32, 35, 38, 41, - 6, 10, 14, 18, 22, 26, 30, 33, 37, 41, 44, 48, 51, 54, 58, 61, - 21, 26, 31, 35, 40, 44, 49, 53, 57, 61, 65, 68, 72, 75, 79, 82, - 40, 45, 51, 56, 61, 66, 70, 75, 79, 83, 87, 91, 94, 98, 101, 104, - 60, 66, 72, 77, 82, 87, 92, 96, 100, 104, 108, 111, 114, 117, 119, 121, - 83, 89, 95, 100, 105, 109, 113, 116, 119, 122, 124, - 104, 109, 114, 118, 121, 124}; - -/****************************************************************************** - * Set the phy type member in the hw struct. - * - * hw - Struct containing variables accessed by shared code - *****************************************************************************/ -STATIC int32_t -em_set_phy_type(struct em_hw *hw) -{ - DEBUGFUNC("em_set_phy_type"); - - if (hw->mac_type == em_undefined) - return -E1000_ERR_PHY_TYPE; - - switch (hw->phy_id) { - case M88E1000_E_PHY_ID: - case M88E1000_I_PHY_ID: - case M88E1011_I_PHY_ID: - case M88E1111_I_PHY_ID: - hw->phy_type = em_phy_m88; - break; - case IGP01E1000_I_PHY_ID: - if (hw->mac_type == em_82541 || - hw->mac_type == em_82541_rev_2 || - hw->mac_type == em_82547 || - hw->mac_type == em_82547_rev_2) { - hw->phy_type = em_phy_igp; - break; - } - case IGP03E1000_E_PHY_ID: - hw->phy_type = em_phy_igp_3; - break; - case IFE_E_PHY_ID: - case IFE_PLUS_E_PHY_ID: - case IFE_C_E_PHY_ID: - hw->phy_type = em_phy_ife; - break; - case GG82563_E_PHY_ID: - if (hw->mac_type == em_80003es2lan) { - hw->phy_type = em_phy_gg82563; - break; - } - /* Fall Through */ - default: - /* Should never have loaded on this device */ - hw->phy_type = em_phy_undefined; - return -E1000_ERR_PHY_TYPE; - } - - return E1000_SUCCESS; -} - -/****************************************************************************** - * IGP phy init script - initializes the GbE PHY - * - * hw - Struct containing variables accessed by shared code - *****************************************************************************/ -static void -em_phy_init_script(struct em_hw *hw) -{ - uint32_t ret_val; - uint16_t phy_saved_data; - - DEBUGFUNC("em_phy_init_script"); - - if (hw->phy_init_script) { - msec_delay(20); - - /* Save off the current value of register 0x2F5B to be restored at - * the end of this routine. */ - ret_val = em_read_phy_reg(hw, 0x2F5B, &phy_saved_data); - - /* Disabled the PHY transmitter */ - em_write_phy_reg(hw, 0x2F5B, 0x0003); - - msec_delay(20); - - em_write_phy_reg(hw,0x0000,0x0140); - - msec_delay(5); - - switch (hw->mac_type) { - case em_82541: - case em_82547: - em_write_phy_reg(hw, 0x1F95, 0x0001); - - em_write_phy_reg(hw, 0x1F71, 0xBD21); - - em_write_phy_reg(hw, 0x1F79, 0x0018); - - em_write_phy_reg(hw, 0x1F30, 0x1600); - - em_write_phy_reg(hw, 0x1F31, 0x0014); - - em_write_phy_reg(hw, 0x1F32, 0x161C); - - em_write_phy_reg(hw, 0x1F94, 0x0003); - - em_write_phy_reg(hw, 0x1F96, 0x003F); - - em_write_phy_reg(hw, 0x2010, 0x0008); - break; - - case em_82541_rev_2: - case em_82547_rev_2: - em_write_phy_reg(hw, 0x1F73, 0x0099); - break; - default: - break; - } - - em_write_phy_reg(hw, 0x0000, 0x3300); - - msec_delay(20); - - /* Now enable the transmitter */ - em_write_phy_reg(hw, 0x2F5B, phy_saved_data); - - if (hw->mac_type == em_82547) { - uint16_t fused, fine, coarse; - - /* Move to analog registers page */ - em_read_phy_reg(hw, IGP01E1000_ANALOG_SPARE_FUSE_STATUS, &fused); - - if (!(fused & IGP01E1000_ANALOG_SPARE_FUSE_ENABLED)) { - em_read_phy_reg(hw, IGP01E1000_ANALOG_FUSE_STATUS, &fused); - - fine = fused & IGP01E1000_ANALOG_FUSE_FINE_MASK; - coarse = fused & IGP01E1000_ANALOG_FUSE_COARSE_MASK; - - if (coarse > IGP01E1000_ANALOG_FUSE_COARSE_THRESH) { - coarse -= IGP01E1000_ANALOG_FUSE_COARSE_10; - fine -= IGP01E1000_ANALOG_FUSE_FINE_1; - } else if (coarse == IGP01E1000_ANALOG_FUSE_COARSE_THRESH) - fine -= IGP01E1000_ANALOG_FUSE_FINE_10; - - fused = (fused & IGP01E1000_ANALOG_FUSE_POLY_MASK) | - (fine & IGP01E1000_ANALOG_FUSE_FINE_MASK) | - (coarse & IGP01E1000_ANALOG_FUSE_COARSE_MASK); - - em_write_phy_reg(hw, IGP01E1000_ANALOG_FUSE_CONTROL, fused); - em_write_phy_reg(hw, IGP01E1000_ANALOG_FUSE_BYPASS, - IGP01E1000_ANALOG_FUSE_ENABLE_SW_CONTROL); - } - } - } -} - -/****************************************************************************** - * Set the mac type member in the hw struct. - * - * hw - Struct containing variables accessed by shared code - *****************************************************************************/ -int32_t -em_set_mac_type(struct em_hw *hw) -{ - DEBUGFUNC("em_set_mac_type"); - - switch (hw->device_id) { - case E1000_DEV_ID_82542: - switch (hw->revision_id) { - case E1000_82542_2_0_REV_ID: - hw->mac_type = em_82542_rev2_0; - break; - case E1000_82542_2_1_REV_ID: - hw->mac_type = em_82542_rev2_1; - break; - default: - /* Invalid 82542 revision ID */ - return -E1000_ERR_MAC_TYPE; - } - break; - case E1000_DEV_ID_82543GC_FIBER: - case E1000_DEV_ID_82543GC_COPPER: - hw->mac_type = em_82543; - break; - case E1000_DEV_ID_82544EI_COPPER: - case E1000_DEV_ID_82544EI_FIBER: - case E1000_DEV_ID_82544GC_COPPER: - case E1000_DEV_ID_82544GC_LOM: - hw->mac_type = em_82544; - break; - case E1000_DEV_ID_82540EM: - case E1000_DEV_ID_82540EM_LOM: - case E1000_DEV_ID_82540EP: - case E1000_DEV_ID_82540EP_LOM: - case E1000_DEV_ID_82540EP_LP: - hw->mac_type = em_82540; - break; - case E1000_DEV_ID_82545EM_COPPER: - case E1000_DEV_ID_82545EM_FIBER: - hw->mac_type = em_82545; - break; - case E1000_DEV_ID_82545GM_COPPER: - case E1000_DEV_ID_82545GM_FIBER: - case E1000_DEV_ID_82545GM_SERDES: - hw->mac_type = em_82545_rev_3; - break; - case E1000_DEV_ID_82546EB_COPPER: - case E1000_DEV_ID_82546EB_FIBER: - case E1000_DEV_ID_82546EB_QUAD_COPPER: - hw->mac_type = em_82546; - break; - case E1000_DEV_ID_82546GB_COPPER: - case E1000_DEV_ID_82546GB_FIBER: - case E1000_DEV_ID_82546GB_SERDES: - case E1000_DEV_ID_82546GB_PCIE: - case E1000_DEV_ID_82546GB_QUAD_COPPER: - case E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3: - hw->mac_type = em_82546_rev_3; - break; - case E1000_DEV_ID_82541EI: - case E1000_DEV_ID_82541EI_MOBILE: - case E1000_DEV_ID_82541ER_LOM: - hw->mac_type = em_82541; - break; - case E1000_DEV_ID_82541ER: - case E1000_DEV_ID_82541GI: - case E1000_DEV_ID_82541GI_LF: - case E1000_DEV_ID_82541GI_MOBILE: - hw->mac_type = em_82541_rev_2; - break; - case E1000_DEV_ID_82547EI: - case E1000_DEV_ID_82547EI_MOBILE: - hw->mac_type = em_82547; - break; - case E1000_DEV_ID_82547GI: - hw->mac_type = em_82547_rev_2; - break; - case E1000_DEV_ID_82571EB_COPPER: - case E1000_DEV_ID_82571EB_FIBER: - case E1000_DEV_ID_82571EB_SERDES: - case E1000_DEV_ID_82571EB_QUAD_COPPER: - case E1000_DEV_ID_82571EB_QUAD_COPPER_LOWPROFILE: - hw->mac_type = em_82571; - break; - case E1000_DEV_ID_82572EI_COPPER: - case E1000_DEV_ID_82572EI_FIBER: - case E1000_DEV_ID_82572EI_SERDES: - case E1000_DEV_ID_82572EI: - hw->mac_type = em_82572; - break; - case E1000_DEV_ID_82573E: - case E1000_DEV_ID_82573E_IAMT: - case E1000_DEV_ID_82573L: - hw->mac_type = em_82573; - break; - case E1000_DEV_ID_80003ES2LAN_COPPER_SPT: - case E1000_DEV_ID_80003ES2LAN_SERDES_SPT: - case E1000_DEV_ID_80003ES2LAN_COPPER_DPT: - case E1000_DEV_ID_80003ES2LAN_SERDES_DPT: - hw->mac_type = em_80003es2lan; - break; - case E1000_DEV_ID_ICH8_IGP_M_AMT: - case E1000_DEV_ID_ICH8_IGP_AMT: - case E1000_DEV_ID_ICH8_IGP_C: - case E1000_DEV_ID_ICH8_IFE: - case E1000_DEV_ID_ICH8_IFE_GT: - case E1000_DEV_ID_ICH8_IFE_G: - case E1000_DEV_ID_ICH8_IGP_M: - hw->mac_type = em_ich8lan; - break; - case E1000_DEV_ID_ICH9_IGP_AMT: - case E1000_DEV_ID_ICH9_IGP_C: - case E1000_DEV_ID_ICH9_IFE: - case E1000_DEV_ID_ICH9_IFE_GT: - case E1000_DEV_ID_ICH9_IFE_G: - hw->mac_type = em_ich9lan; - break; - default: - /* Should never have loaded on this device */ - return -E1000_ERR_MAC_TYPE; - } - - switch (hw->mac_type) { - case em_ich8lan: - case em_ich9lan: - hw->swfwhw_semaphore_present = TRUE; - hw->asf_firmware_present = TRUE; - break; - case em_80003es2lan: - hw->swfw_sync_present = TRUE; - /* fall through */ - case em_82571: - case em_82572: - case em_82573: - hw->eeprom_semaphore_present = TRUE; - /* fall through */ - case em_82541: - case em_82547: - case em_82541_rev_2: - case em_82547_rev_2: - hw->asf_firmware_present = TRUE; - break; - default: - break; - } - - return E1000_SUCCESS; -} - -/***************************************************************************** - * Set media type and TBI compatibility. - * - * hw - Struct containing variables accessed by shared code - * **************************************************************************/ -void -em_set_media_type(struct em_hw *hw) -{ - uint32_t status; - - DEBUGFUNC("em_set_media_type"); - - if (hw->mac_type != em_82543) { - /* tbi_compatibility is only valid on 82543 */ - hw->tbi_compatibility_en = FALSE; - } - - switch (hw->device_id) { - case E1000_DEV_ID_82545GM_SERDES: - case E1000_DEV_ID_82546GB_SERDES: - case E1000_DEV_ID_82571EB_SERDES: - case E1000_DEV_ID_82572EI_SERDES: - case E1000_DEV_ID_80003ES2LAN_SERDES_DPT: - hw->media_type = em_media_type_internal_serdes; - break; - default: - switch (hw->mac_type) { - case em_82542_rev2_0: - case em_82542_rev2_1: - hw->media_type = em_media_type_fiber; - break; - case em_ich8lan: - case em_ich9lan: - case em_82573: - /* The STATUS_TBIMODE bit is reserved or reused for the this - * device. - */ - hw->media_type = em_media_type_copper; - break; - default: - status = E1000_READ_REG(hw, STATUS); - if (status & E1000_STATUS_TBIMODE) { - hw->media_type = em_media_type_fiber; - /* tbi_compatibility not valid on fiber */ - hw->tbi_compatibility_en = FALSE; - } else { - hw->media_type = em_media_type_copper; - } - break; - } - } -} - -/****************************************************************************** - * Reset the transmit and receive units; mask and clear all interrupts. - * - * hw - Struct containing variables accessed by shared code - *****************************************************************************/ -int32_t -em_reset_hw(struct em_hw *hw) -{ - uint32_t ctrl; - uint32_t ctrl_ext; - uint32_t icr; - uint32_t manc; - uint32_t led_ctrl; - uint32_t timeout; - uint32_t extcnf_ctrl; - int32_t ret_val; - - DEBUGFUNC("em_reset_hw"); - - /* For 82542 (rev 2.0), disable MWI before issuing a device reset */ - if (hw->mac_type == em_82542_rev2_0) { - DEBUGOUT("Disabling MWI on 82542 rev 2.0\n"); - em_pci_clear_mwi(hw); - } - - if (hw->bus_type == em_bus_type_pci_express) { - /* Prevent the PCI-E bus from sticking if there is no TLP connection - * on the last TLP read/write transaction when MAC is reset. - */ - if (em_disable_pciex_master(hw) != E1000_SUCCESS) { - DEBUGOUT("PCI-E Master disable polling has failed.\n"); - } - } - - /* Clear interrupt mask to stop board from generating interrupts */ - DEBUGOUT("Masking off all interrupts\n"); - E1000_WRITE_REG(hw, IMC, 0xffffffff); - - /* Disable the Transmit and Receive units. Then delay to allow - * any pending transactions to complete before we hit the MAC with - * the global reset. - */ - E1000_WRITE_REG(hw, RCTL, 0); - E1000_WRITE_REG(hw, TCTL, E1000_TCTL_PSP); - E1000_WRITE_FLUSH(hw); - - /* The tbi_compatibility_on Flag must be cleared when Rctl is cleared. */ - hw->tbi_compatibility_on = FALSE; - - /* Delay to allow any outstanding PCI transactions to complete before - * resetting the device - */ - msec_delay(10); - - ctrl = E1000_READ_REG(hw, CTRL); - - /* Must reset the PHY before resetting the MAC */ - if ((hw->mac_type == em_82541) || (hw->mac_type == em_82547)) { - E1000_WRITE_REG(hw, CTRL, (ctrl | E1000_CTRL_PHY_RST)); - msec_delay(5); - } - - /* Must acquire the MDIO ownership before MAC reset. - * Ownership defaults to firmware after a reset. */ - if (hw->mac_type == em_82573) { - timeout = 10; - - extcnf_ctrl = E1000_READ_REG(hw, EXTCNF_CTRL); - extcnf_ctrl |= E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP; - - do { - E1000_WRITE_REG(hw, EXTCNF_CTRL, extcnf_ctrl); - extcnf_ctrl = E1000_READ_REG(hw, EXTCNF_CTRL); - - if (extcnf_ctrl & E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP) - break; - else - extcnf_ctrl |= E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP; - - msec_delay(2); - timeout--; - } while (timeout); - } - - /* Workaround for ICH8 bit corruption issue in FIFO memory */ - if (hw->mac_type == em_ich8lan) { - /* Set Tx and Rx buffer allocation to 8k apiece. */ - E1000_WRITE_REG(hw, PBA, E1000_PBA_8K); - /* Set Packet Buffer Size to 16k. */ - E1000_WRITE_REG(hw, PBS, E1000_PBS_16K); - } - - /* Issue a global reset to the MAC. This will reset the chip's - * transmit, receive, DMA, and link units. It will not effect - * the current PCI configuration. The global reset bit is self- - * clearing, and should clear within a microsecond. - */ - DEBUGOUT("Issuing a global reset to MAC\n"); - - switch (hw->mac_type) { - case em_82544: - case em_82540: - case em_82545: - case em_82546: - case em_82541: - case em_82541_rev_2: - /* These controllers can't ack the 64-bit write when issuing the - * reset, so use IO-mapping as a workaround to issue the reset */ - E1000_WRITE_REG_IO(hw, CTRL, (ctrl | E1000_CTRL_RST)); - break; - case em_82545_rev_3: - case em_82546_rev_3: - /* Reset is performed on a shadow of the control register */ - E1000_WRITE_REG(hw, CTRL_DUP, (ctrl | E1000_CTRL_RST)); - break; - case em_ich8lan: - case em_ich9lan: - if (!hw->phy_reset_disable && - em_check_phy_reset_block(hw) == E1000_SUCCESS) { - /* em_ich8lan PHY HW reset requires MAC CORE reset - * at the same time to make sure the interface between - * MAC and the external PHY is reset. - */ - ctrl |= E1000_CTRL_PHY_RST; - } - - em_get_software_flag(hw); - E1000_WRITE_REG(hw, CTRL, (ctrl | E1000_CTRL_RST)); - msec_delay(5); - break; - default: - E1000_WRITE_REG(hw, CTRL, (ctrl | E1000_CTRL_RST)); - break; - } - - /* After MAC reset, force reload of EEPROM to restore power-on settings to - * device. Later controllers reload the EEPROM automatically, so just wait - * for reload to complete. - */ - switch (hw->mac_type) { - case em_82542_rev2_0: - case em_82542_rev2_1: - case em_82543: - case em_82544: - /* Wait for reset to complete */ - usec_delay(10); - ctrl_ext = E1000_READ_REG(hw, CTRL_EXT); - ctrl_ext |= E1000_CTRL_EXT_EE_RST; - E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext); - E1000_WRITE_FLUSH(hw); - /* Wait for EEPROM reload */ - msec_delay(2); - break; - case em_82541: - case em_82541_rev_2: - case em_82547: - case em_82547_rev_2: - /* Wait for EEPROM reload */ - msec_delay(20); - break; - case em_82573: - if (em_is_onboard_nvm_eeprom(hw) == FALSE) { - usec_delay(10); - ctrl_ext = E1000_READ_REG(hw, CTRL_EXT); - ctrl_ext |= E1000_CTRL_EXT_EE_RST; - E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext); - E1000_WRITE_FLUSH(hw); - } - /* fall through */ - default: - /* Auto read done will delay 5ms or poll based on mac type */ - ret_val = em_get_auto_rd_done(hw); - if (ret_val) - return ret_val; - break; - } - - /* Disable HW ARPs on ASF enabled adapters */ - if (hw->mac_type >= em_82540 && hw->mac_type <= em_82547_rev_2) { - manc = E1000_READ_REG(hw, MANC); - manc &= ~(E1000_MANC_ARP_EN); - E1000_WRITE_REG(hw, MANC, manc); - } - - if ((hw->mac_type == em_82541) || (hw->mac_type == em_82547)) { - em_phy_init_script(hw); - - /* Configure activity LED after PHY reset */ - led_ctrl = E1000_READ_REG(hw, LEDCTL); - led_ctrl &= IGP_ACTIVITY_LED_MASK; - led_ctrl |= (IGP_ACTIVITY_LED_ENABLE | IGP_LED3_MODE); - E1000_WRITE_REG(hw, LEDCTL, led_ctrl); - } - - /* Clear interrupt mask to stop board from generating interrupts */ - DEBUGOUT("Masking off all interrupts\n"); - E1000_WRITE_REG(hw, IMC, 0xffffffff); - - /* Clear any pending interrupt events. */ - icr = E1000_READ_REG(hw, ICR); - - /* If MWI was previously enabled, reenable it. */ - if (hw->mac_type == em_82542_rev2_0) { - if (hw->pci_cmd_word & CMD_MEM_WRT_INVALIDATE) - em_pci_set_mwi(hw); - } - - if (hw->mac_type == em_ich8lan || hw->mac_type == em_ich9lan) { - uint32_t kab = E1000_READ_REG(hw, KABGTXD); - kab |= E1000_KABGTXD_BGSQLBIAS; - E1000_WRITE_REG(hw, KABGTXD, kab); - } - - return E1000_SUCCESS; -} - -/****************************************************************************** - * - * Initialize a number of hardware-dependent bits - * - * hw: Struct containing variables accessed by shared code - * - *****************************************************************************/ -STATIC void -em_initialize_hardware_bits(struct em_hw *hw) -{ - if ((hw->mac_type >= em_82571) && (!hw->initialize_hw_bits_disable)) { - /* Settings common to all silicon */ - uint32_t reg_ctrl, reg_ctrl_ext; - uint32_t reg_tarc0, reg_tarc1; - uint32_t reg_tctl; - uint32_t reg_txdctl, reg_txdctl1; - - reg_tarc0 = E1000_READ_REG(hw, TARC0); - reg_tarc0 &= ~0x78000000; /* Clear bits 30, 29, 28, and 27 */ - - reg_txdctl = E1000_READ_REG(hw, TXDCTL); - reg_txdctl |= E1000_TXDCTL_COUNT_DESC; /* Set bit 22 */ - E1000_WRITE_REG(hw, TXDCTL, reg_txdctl); - - reg_txdctl1 = E1000_READ_REG(hw, TXDCTL1); - reg_txdctl1 |= E1000_TXDCTL_COUNT_DESC; /* Set bit 22 */ - E1000_WRITE_REG(hw, TXDCTL1, reg_txdctl1); - - switch (hw->mac_type) { - case em_82571: - case em_82572: - reg_tarc1 = E1000_READ_REG(hw, TARC1); - reg_tctl = E1000_READ_REG(hw, TCTL); - - /* Set the phy Tx compatible mode bits */ - reg_tarc1 &= ~0x60000000; /* Clear bits 30 and 29 */ - - reg_tarc0 |= 0x07800000; /* Set TARC0 bits 23-26 */ - reg_tarc1 |= 0x07000000; /* Set TARC1 bits 24-26 */ - - if (reg_tctl & E1000_TCTL_MULR) - reg_tarc1 &= ~0x10000000; /* Clear bit 28 if MULR is 1b */ - else - reg_tarc1 |= 0x10000000; /* Set bit 28 if MULR is 0b */ - - E1000_WRITE_REG(hw, TARC1, reg_tarc1); - break; - case em_82573: - reg_ctrl_ext = E1000_READ_REG(hw, CTRL_EXT); - reg_ctrl = E1000_READ_REG(hw, CTRL); - - reg_ctrl_ext &= ~0x00800000; /* Clear bit 23 */ - reg_ctrl_ext |= 0x00400000; /* Set bit 22 */ - reg_ctrl &= ~0x20000000; /* Clear bit 29 */ - - E1000_WRITE_REG(hw, CTRL_EXT, reg_ctrl_ext); - E1000_WRITE_REG(hw, CTRL, reg_ctrl); - break; - case em_80003es2lan: - if ((hw->media_type == em_media_type_fiber) || - (hw->media_type == em_media_type_internal_serdes)) { - reg_tarc0 &= ~0x00100000; /* Clear bit 20 */ - } - - reg_tctl = E1000_READ_REG(hw, TCTL); - reg_tarc1 = E1000_READ_REG(hw, TARC1); - if (reg_tctl & E1000_TCTL_MULR) - reg_tarc1 &= ~0x10000000; /* Clear bit 28 if MULR is 1b */ - else - reg_tarc1 |= 0x10000000; /* Set bit 28 if MULR is 0b */ - - E1000_WRITE_REG(hw, TARC1, reg_tarc1); - break; - case em_ich8lan: - case em_ich9lan: - if ((hw->revision_id < 3) || - ((hw->device_id != E1000_DEV_ID_ICH8_IGP_M_AMT) && - (hw->device_id != E1000_DEV_ID_ICH8_IGP_M))) - reg_tarc0 |= 0x30000000; /* Set TARC0 bits 29 and 28 */ - reg_ctrl_ext = E1000_READ_REG(hw, CTRL_EXT); - reg_ctrl_ext |= 0x00400000; /* Set bit 22 */ - E1000_WRITE_REG(hw, CTRL_EXT, reg_ctrl_ext); - - reg_tarc0 |= 0x0d800000; /* Set TARC0 bits 23, 24, 26, 27 */ - - reg_tarc1 = E1000_READ_REG(hw, TARC1); - reg_tctl = E1000_READ_REG(hw, TCTL); - - if (reg_tctl & E1000_TCTL_MULR) - reg_tarc1 &= ~0x10000000; /* Clear bit 28 if MULR is 1b */ - else - reg_tarc1 |= 0x10000000; /* Set bit 28 if MULR is 0b */ - - reg_tarc1 |= 0x45000000; /* Set bit 24, 26 and 30 */ - - E1000_WRITE_REG(hw, TARC1, reg_tarc1); - break; - default: - break; - } - - E1000_WRITE_REG(hw, TARC0, reg_tarc0); - } -} - -/****************************************************************************** - * Performs basic configuration of the adapter. - * - * hw - Struct containing variables accessed by shared code - * - * Assumes that the controller has previously been reset and is in a - * post-reset uninitialized state. Initializes the receive address registers, - * multicast table, and VLAN filter table. Calls routines to setup link - * configuration and flow control settings. Clears all on-chip counters. Leaves - * the transmit and receive units disabled and uninitialized. - *****************************************************************************/ -int32_t -em_init_hw(struct em_hw *hw) -{ - uint32_t ctrl; - uint32_t i; - int32_t ret_val; - uint16_t pcix_cmd_word; - uint16_t pcix_stat_hi_word; - uint16_t cmd_mmrbc; - uint16_t stat_mmrbc; - uint32_t mta_size; - uint32_t reg_data; - uint32_t ctrl_ext; - - DEBUGFUNC("em_init_hw"); - - /* force full DMA clock frequency for 10/100 on ICH8 A0-B0 */ - if ((hw->mac_type == em_ich8lan) && - ((hw->revision_id < 3) || - ((hw->device_id != E1000_DEV_ID_ICH8_IGP_M_AMT) && - (hw->device_id != E1000_DEV_ID_ICH8_IGP_M)))) { - reg_data = E1000_READ_REG(hw, STATUS); - reg_data &= ~0x80000000; - E1000_WRITE_REG(hw, STATUS, reg_data); - } - /* Initialize Identification LED */ - ret_val = em_id_led_init(hw); - if (ret_val) { - DEBUGOUT("Error Initializing Identification LED\n"); - return ret_val; - } - - /* Set the media type and TBI compatibility */ - em_set_media_type(hw); - - /* Disabling VLAN filtering. */ - DEBUGOUT("Initializing the IEEE VLAN\n"); - /* VET hardcoded to standard value and VFTA removed in ICH8 LAN */ - if (hw->mac_type != em_ich8lan) { - if (hw->mac_type < em_82545_rev_3) - E1000_WRITE_REG(hw, VET, 0); - em_clear_vfta(hw); - } - - /* For 82542 (rev 2.0), disable MWI and put the receiver into reset */ - if (hw->mac_type == em_82542_rev2_0) { - DEBUGOUT("Disabling MWI on 82542 rev 2.0\n"); - em_pci_clear_mwi(hw); - E1000_WRITE_REG(hw, RCTL, E1000_RCTL_RST); - E1000_WRITE_FLUSH(hw); - msec_delay(5); - } - - /* Setup the receive address. This involves initializing all of the Receive - * Address Registers (RARs 0 - 15). - */ - em_init_rx_addrs(hw); - - /* For 82542 (rev 2.0), take the receiver out of reset and enable MWI */ - if (hw->mac_type == em_82542_rev2_0) { - E1000_WRITE_REG(hw, RCTL, 0); - E1000_WRITE_FLUSH(hw); - msec_delay(1); - if (hw->pci_cmd_word & CMD_MEM_WRT_INVALIDATE) - em_pci_set_mwi(hw); - } - - /* Zero out the Multicast HASH table */ - DEBUGOUT("Zeroing the MTA\n"); - mta_size = E1000_MC_TBL_SIZE; - if (hw->mac_type == em_ich8lan || hw->mac_type == em_ich9lan) - mta_size = E1000_MC_TBL_SIZE_ICH8LAN; - for (i = 0; i < mta_size; i++) { - E1000_WRITE_REG_ARRAY(hw, MTA, i, 0); - /* use write flush to prevent Memory Write Block (MWB) from - * occuring when accessing our register space */ - E1000_WRITE_FLUSH(hw); - } - - /* Set the PCI priority bit correctly in the CTRL register. This - * determines if the adapter gives priority to receives, or if it - * gives equal priority to transmits and receives. Valid only on - * 82542 and 82543 silicon. - */ - if (hw->dma_fairness && hw->mac_type <= em_82543) { - ctrl = E1000_READ_REG(hw, CTRL); - E1000_WRITE_REG(hw, CTRL, ctrl | E1000_CTRL_PRIOR); - } - - switch (hw->mac_type) { - case em_82545_rev_3: - case em_82546_rev_3: - break; - default: - /* Workaround for PCI-X problem when BIOS sets MMRBC incorrectly. */ - if (hw->bus_type == em_bus_type_pcix) { - em_read_pci_cfg(hw, PCIX_COMMAND_REGISTER, &pcix_cmd_word); - em_read_pci_cfg(hw, PCIX_STATUS_REGISTER_HI, - &pcix_stat_hi_word); - cmd_mmrbc = (pcix_cmd_word & PCIX_COMMAND_MMRBC_MASK) >> - PCIX_COMMAND_MMRBC_SHIFT; - stat_mmrbc = (pcix_stat_hi_word & PCIX_STATUS_HI_MMRBC_MASK) >> - PCIX_STATUS_HI_MMRBC_SHIFT; - if (stat_mmrbc == PCIX_STATUS_HI_MMRBC_4K) - stat_mmrbc = PCIX_STATUS_HI_MMRBC_2K; - if (cmd_mmrbc > stat_mmrbc) { - pcix_cmd_word &= ~PCIX_COMMAND_MMRBC_MASK; - pcix_cmd_word |= stat_mmrbc << PCIX_COMMAND_MMRBC_SHIFT; - em_write_pci_cfg(hw, PCIX_COMMAND_REGISTER, - &pcix_cmd_word); - } - } - break; - } - - /* More time needed for PHY to initialize */ - if (hw->mac_type == em_ich8lan || hw->mac_type == em_ich9lan) - msec_delay(15); - - /* Call a subroutine to configure the link and setup flow control. */ - ret_val = em_setup_link(hw); - - /* Set the transmit descriptor write-back policy */ - if (hw->mac_type > em_82544) { - ctrl = E1000_READ_REG(hw, TXDCTL); - ctrl = (ctrl & ~E1000_TXDCTL_WTHRESH) | E1000_TXDCTL_FULL_TX_DESC_WB; - E1000_WRITE_REG(hw, TXDCTL, ctrl); - } - - if (hw->mac_type == em_82573) { - em_enable_tx_pkt_filtering(hw); - } - - switch (hw->mac_type) { - default: - break; - case em_80003es2lan: - /* Enable retransmit on late collisions */ - reg_data = E1000_READ_REG(hw, TCTL); - reg_data |= E1000_TCTL_RTLC; - E1000_WRITE_REG(hw, TCTL, reg_data); - - /* Configure Gigabit Carry Extend Padding */ - reg_data = E1000_READ_REG(hw, TCTL_EXT); - reg_data &= ~E1000_TCTL_EXT_GCEX_MASK; - reg_data |= DEFAULT_80003ES2LAN_TCTL_EXT_GCEX; - E1000_WRITE_REG(hw, TCTL_EXT, reg_data); - - /* Configure Transmit Inter-Packet Gap */ - reg_data = E1000_READ_REG(hw, TIPG); - reg_data &= ~E1000_TIPG_IPGT_MASK; - reg_data |= DEFAULT_80003ES2LAN_TIPG_IPGT_1000; - E1000_WRITE_REG(hw, TIPG, reg_data); - - reg_data = E1000_READ_REG_ARRAY(hw, FFLT, 0x0001); - reg_data &= ~0x00100000; - E1000_WRITE_REG_ARRAY(hw, FFLT, 0x0001, reg_data); - /* Fall through */ - case em_82571: - case em_82572: - case em_ich9lan: - case em_ich8lan: - ctrl = E1000_READ_REG(hw, TXDCTL1); - ctrl = (ctrl & ~E1000_TXDCTL_WTHRESH) | E1000_TXDCTL_FULL_TX_DESC_WB; - E1000_WRITE_REG(hw, TXDCTL1, ctrl); - break; - } - - - if (hw->mac_type == em_82573) { - uint32_t gcr = E1000_READ_REG(hw, GCR); - gcr |= E1000_GCR_L1_ACT_WITHOUT_L0S_RX; - E1000_WRITE_REG(hw, GCR, gcr); - } - - /* Clear all of the statistics registers (clear on read). It is - * important that we do this after we have tried to establish link - * because the symbol error count will increment wildly if there - * is no link. - */ - em_clear_hw_cntrs(hw); - - /* ICH8 No-snoop bits are opposite polarity. - * Set to snoop by default after reset. */ - if (hw->mac_type == em_ich8lan) - em_set_pci_ex_no_snoop(hw, PCI_EX_82566_SNOOP_ALL); - - if (hw->device_id == E1000_DEV_ID_82546GB_QUAD_COPPER || - hw->device_id == E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3) { - ctrl_ext = E1000_READ_REG(hw, CTRL_EXT); - /* Relaxed ordering must be disabled to avoid a parity - * error crash in a PCI slot. */ - ctrl_ext |= E1000_CTRL_EXT_RO_DIS; - E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext); - } - - /* Must be called after em_set_media_type because media_type is used */ - em_initialize_hardware_bits(hw); - - return ret_val; -} - -/****************************************************************************** - * Adjust SERDES output amplitude based on EEPROM setting. - * - * hw - Struct containing variables accessed by shared code. - *****************************************************************************/ -static int32_t -em_adjust_serdes_amplitude(struct em_hw *hw) -{ - uint16_t eeprom_data; - int32_t ret_val; - - DEBUGFUNC("em_adjust_serdes_amplitude"); - - if (hw->media_type != em_media_type_internal_serdes) - return E1000_SUCCESS; - - switch (hw->mac_type) { - case em_82545_rev_3: - case em_82546_rev_3: - break; - default: - return E1000_SUCCESS; - } - - ret_val = em_read_eeprom(hw, EEPROM_SERDES_AMPLITUDE, 1, &eeprom_data); - if (ret_val) { - return ret_val; - } - - if (eeprom_data != EEPROM_RESERVED_WORD) { - /* Adjust SERDES output amplitude only. */ - eeprom_data &= EEPROM_SERDES_AMPLITUDE_MASK; - ret_val = em_write_phy_reg(hw, M88E1000_PHY_EXT_CTRL, eeprom_data); - if (ret_val) - return ret_val; - } - - return E1000_SUCCESS; -} - -/****************************************************************************** - * Configures flow control and link settings. - * - * hw - Struct containing variables accessed by shared code - * - * Determines which flow control settings to use. Calls the apropriate media- - * specific link configuration function. Configures the flow control settings. - * Assuming the adapter has a valid link partner, a valid link should be - * established. Assumes the hardware has previously been reset and the - * transmitter and receiver are not enabled. - *****************************************************************************/ -int32_t -em_setup_link(struct em_hw *hw) -{ - uint32_t ctrl_ext; - int32_t ret_val; - uint16_t eeprom_data; - - DEBUGFUNC("em_setup_link"); - - /* In the case of the phy reset being blocked, we already have a link. - * We do not have to set it up again. */ - if (em_check_phy_reset_block(hw)) - return E1000_SUCCESS; - - /* Read and store word 0x0F of the EEPROM. This word contains bits - * that determine the hardware's default PAUSE (flow control) mode, - * a bit that determines whether the HW defaults to enabling or - * disabling auto-negotiation, and the direction of the - * SW defined pins. If there is no SW over-ride of the flow - * control setting, then the variable hw->fc will - * be initialized based on a value in the EEPROM. - */ - if (hw->fc == E1000_FC_DEFAULT) { - switch (hw->mac_type) { - case em_ich8lan: - case em_ich9lan: - case em_82573: - hw->fc = E1000_FC_FULL; - break; - default: - ret_val = em_read_eeprom(hw, EEPROM_INIT_CONTROL2_REG, - 1, &eeprom_data); - if (ret_val) { - DEBUGOUT("EEPROM Read Error\n"); - return -E1000_ERR_EEPROM; - } - if ((eeprom_data & EEPROM_WORD0F_PAUSE_MASK) == 0) - hw->fc = E1000_FC_NONE; - else if ((eeprom_data & EEPROM_WORD0F_PAUSE_MASK) == - EEPROM_WORD0F_ASM_DIR) - hw->fc = E1000_FC_TX_PAUSE; - else - hw->fc = E1000_FC_FULL; - break; - } - } - - /* We want to save off the original Flow Control configuration just - * in case we get disconnected and then reconnected into a different - * hub or switch with different Flow Control capabilities. - */ - if (hw->mac_type == em_82542_rev2_0) - hw->fc &= (~E1000_FC_TX_PAUSE); - - if ((hw->mac_type < em_82543) && (hw->report_tx_early == 1)) - hw->fc &= (~E1000_FC_RX_PAUSE); - - hw->original_fc = hw->fc; - - DEBUGOUT1("After fix-ups FlowControl is now = %x\n", hw->fc); - - /* Take the 4 bits from EEPROM word 0x0F that determine the initial - * polarity value for the SW controlled pins, and setup the - * Extended Device Control reg with that info. - * This is needed because one of the SW controlled pins is used for - * signal detection. So this should be done before em_setup_pcs_link() - * or em_phy_setup() is called. - */ - if (hw->mac_type == em_82543) { - ret_val = em_read_eeprom(hw, EEPROM_INIT_CONTROL2_REG, - 1, &eeprom_data); - if (ret_val) { - DEBUGOUT("EEPROM Read Error\n"); - return -E1000_ERR_EEPROM; - } - ctrl_ext = ((eeprom_data & EEPROM_WORD0F_SWPDIO_EXT) << - SWDPIO__EXT_SHIFT); - E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext); - } - - /* Call the necessary subroutine to configure the link. */ - ret_val = (hw->media_type == em_media_type_copper) ? - em_setup_copper_link(hw) : - em_setup_fiber_serdes_link(hw); - - /* Initialize the flow control address, type, and PAUSE timer - * registers to their default values. This is done even if flow - * control is disabled, because it does not hurt anything to - * initialize these registers. - */ - DEBUGOUT("Initializing the Flow Control address, type and timer regs\n"); - - /* FCAL/H and FCT are hardcoded to standard values in em_ich8lan. */ - if (hw->mac_type != em_ich8lan) { - E1000_WRITE_REG(hw, FCT, FLOW_CONTROL_TYPE); - E1000_WRITE_REG(hw, FCAH, FLOW_CONTROL_ADDRESS_HIGH); - E1000_WRITE_REG(hw, FCAL, FLOW_CONTROL_ADDRESS_LOW); - } - - E1000_WRITE_REG(hw, FCTTV, hw->fc_pause_time); - - /* Set the flow control receive threshold registers. Normally, - * these registers will be set to a default threshold that may be - * adjusted later by the driver's runtime code. However, if the - * ability to transmit pause frames in not enabled, then these - * registers will be set to 0. - */ - if (!(hw->fc & E1000_FC_TX_PAUSE)) { - E1000_WRITE_REG(hw, FCRTL, 0); - E1000_WRITE_REG(hw, FCRTH, 0); - } else { - /* We need to set up the Receive Threshold high and low water marks - * as well as (optionally) enabling the transmission of XON frames. - */ - if (hw->fc_send_xon) { - E1000_WRITE_REG(hw, FCRTL, (hw->fc_low_water | E1000_FCRTL_XONE)); - E1000_WRITE_REG(hw, FCRTH, hw->fc_high_water); - } else { - E1000_WRITE_REG(hw, FCRTL, hw->fc_low_water); - E1000_WRITE_REG(hw, FCRTH, hw->fc_high_water); - } - } - return ret_val; -} - -/****************************************************************************** - * Sets up link for a fiber based or serdes based adapter - * - * hw - Struct containing variables accessed by shared code - * - * Manipulates Physical Coding Sublayer functions in order to configure - * link. Assumes the hardware has been previously reset and the transmitter - * and receiver are not enabled. - *****************************************************************************/ -static int32_t -em_setup_fiber_serdes_link(struct em_hw *hw) -{ - uint32_t ctrl; - uint32_t status; - uint32_t txcw = 0; - uint32_t i; - uint32_t signal = 0; - int32_t ret_val; - - DEBUGFUNC("em_setup_fiber_serdes_link"); - - /* On 82571 and 82572 Fiber connections, SerDes loopback mode persists - * until explicitly turned off or a power cycle is performed. A read to - * the register does not indicate its status. Therefore, we ensure - * loopback mode is disabled during initialization. - */ - if (hw->mac_type == em_82571 || hw->mac_type == em_82572) - E1000_WRITE_REG(hw, SCTL, E1000_DISABLE_SERDES_LOOPBACK); - - /* On adapters with a MAC newer than 82544, SWDP 1 will be - * set when the optics detect a signal. On older adapters, it will be - * cleared when there is a signal. This applies to fiber media only. - * If we're on serdes media, adjust the output amplitude to value - * set in the EEPROM. - */ - ctrl = E1000_READ_REG(hw, CTRL); - if (hw->media_type == em_media_type_fiber) - signal = (hw->mac_type > em_82544) ? E1000_CTRL_SWDPIN1 : 0; - - ret_val = em_adjust_serdes_amplitude(hw); - if (ret_val) - return ret_val; - - /* Take the link out of reset */ - ctrl &= ~(E1000_CTRL_LRST); - - /* Adjust VCO speed to improve BER performance */ - ret_val = em_set_vco_speed(hw); - if (ret_val) - return ret_val; - - em_config_collision_dist(hw); - - /* Check for a software override of the flow control settings, and setup - * the device accordingly. If auto-negotiation is enabled, then software - * will have to set the "PAUSE" bits to the correct value in the Tranmsit - * Config Word Register (TXCW) and re-start auto-negotiation. However, if - * auto-negotiation is disabled, then software will have to manually - * configure the two flow control enable bits in the CTRL register. - * - * The possible values of the "fc" parameter are: - * 0: Flow control is completely disabled - * 1: Rx flow control is enabled (we can receive pause frames, but - * not send pause frames). - * 2: Tx flow control is enabled (we can send pause frames but we do - * not support receiving pause frames). - * 3: Both Rx and TX flow control (symmetric) are enabled. - */ - switch (hw->fc) { - case E1000_FC_NONE: - /* Flow control is completely disabled by a software over-ride. */ - txcw = (E1000_TXCW_ANE | E1000_TXCW_FD); - break; - case E1000_FC_RX_PAUSE: - /* RX Flow control is enabled and TX Flow control is disabled by a - * software over-ride. Since there really isn't a way to advertise - * that we are capable of RX Pause ONLY, we will advertise that we - * support both symmetric and asymmetric RX PAUSE. Later, we will - * disable the adapter's ability to send PAUSE frames. - */ - txcw = (E1000_TXCW_ANE | E1000_TXCW_FD | E1000_TXCW_PAUSE_MASK); - break; - case E1000_FC_TX_PAUSE: - /* TX Flow control is enabled, and RX Flow control is disabled, by a - * software over-ride. - */ - txcw = (E1000_TXCW_ANE | E1000_TXCW_FD | E1000_TXCW_ASM_DIR); - break; - case E1000_FC_FULL: - /* Flow control (both RX and TX) is enabled by a software over-ride. */ - txcw = (E1000_TXCW_ANE | E1000_TXCW_FD | E1000_TXCW_PAUSE_MASK); - break; - default: - DEBUGOUT("Flow control param set incorrectly\n"); - return -E1000_ERR_CONFIG; - break; - } - - /* Since auto-negotiation is enabled, take the link out of reset (the link - * will be in reset, because we previously reset the chip). This will - * restart auto-negotiation. If auto-neogtiation is successful then the - * link-up status bit will be set and the flow control enable bits (RFCE - * and TFCE) will be set according to their negotiated value. - */ - DEBUGOUT("Auto-negotiation enabled\n"); - - E1000_WRITE_REG(hw, TXCW, txcw); - E1000_WRITE_REG(hw, CTRL, ctrl); - E1000_WRITE_FLUSH(hw); - - hw->txcw = txcw; - msec_delay(1); - - /* If we have a signal (the cable is plugged in) then poll for a "Link-Up" - * indication in the Device Status Register. Time-out if a link isn't - * seen in 500 milliseconds seconds (Auto-negotiation should complete in - * less than 500 milliseconds even if the other end is doing it in SW). - * For internal serdes, we just assume a signal is present, then poll. - */ - if (hw->media_type == em_media_type_internal_serdes || - (E1000_READ_REG(hw, CTRL) & E1000_CTRL_SWDPIN1) == signal) { - DEBUGOUT("Looking for Link\n"); - for (i = 0; i < (LINK_UP_TIMEOUT / 10); i++) { - msec_delay(10); - status = E1000_READ_REG(hw, STATUS); - if (status & E1000_STATUS_LU) break; - } - if (i == (LINK_UP_TIMEOUT / 10)) { - DEBUGOUT("Never got a valid link from auto-neg!!!\n"); - hw->autoneg_failed = 1; - /* AutoNeg failed to achieve a link, so we'll call - * em_check_for_link. This routine will force the link up if - * we detect a signal. This will allow us to communicate with - * non-autonegotiating link partners. - */ - ret_val = em_check_for_link(hw); - if (ret_val) { - DEBUGOUT("Error while checking for link\n"); - return ret_val; - } - hw->autoneg_failed = 0; - } else { - hw->autoneg_failed = 0; - DEBUGOUT("Valid Link Found\n"); - } - } else { - DEBUGOUT("No Signal Detected\n"); - } - return E1000_SUCCESS; -} - -/****************************************************************************** -* Make sure we have a valid PHY and change PHY mode before link setup. -* -* hw - Struct containing variables accessed by shared code -******************************************************************************/ -static int32_t -em_copper_link_preconfig(struct em_hw *hw) -{ - uint32_t ctrl; - int32_t ret_val; - uint16_t phy_data; - - DEBUGFUNC("em_copper_link_preconfig"); - - ctrl = E1000_READ_REG(hw, CTRL); - /* With 82543, we need to force speed and duplex on the MAC equal to what - * the PHY speed and duplex configuration is. In addition, we need to - * perform a hardware reset on the PHY to take it out of reset. - */ - if (hw->mac_type > em_82543) { - ctrl |= E1000_CTRL_SLU; - ctrl &= ~(E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX); - E1000_WRITE_REG(hw, CTRL, ctrl); - } else { - ctrl |= (E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX | E1000_CTRL_SLU); - E1000_WRITE_REG(hw, CTRL, ctrl); - ret_val = em_phy_hw_reset(hw); - if (ret_val) - return ret_val; - } - - /* Make sure we have a valid PHY */ - ret_val = em_detect_gig_phy(hw); - if (ret_val) { - DEBUGOUT("Error, did not detect valid phy.\n"); - return ret_val; - } - DEBUGOUT1("Phy ID = %x \n", hw->phy_id); - - /* Set PHY to class A mode (if necessary) */ - ret_val = em_set_phy_mode(hw); - if (ret_val) - return ret_val; - - if ((hw->mac_type == em_82545_rev_3) || - (hw->mac_type == em_82546_rev_3)) { - ret_val = em_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data); - phy_data |= 0x00000008; - ret_val = em_write_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, phy_data); - } - - if (hw->mac_type <= em_82543 || - hw->mac_type == em_82541 || hw->mac_type == em_82547 || - hw->mac_type == em_82541_rev_2 || hw->mac_type == em_82547_rev_2) - hw->phy_reset_disable = FALSE; - - return E1000_SUCCESS; -} - - -/******************************************************************** -* Copper link setup for em_phy_igp series. -* -* hw - Struct containing variables accessed by shared code -*********************************************************************/ -static int32_t -em_copper_link_igp_setup(struct em_hw *hw) -{ - uint32_t led_ctrl; - int32_t ret_val; - uint16_t phy_data; - - DEBUGFUNC("em_copper_link_igp_setup"); - - if (hw->phy_reset_disable) - return E1000_SUCCESS; - - ret_val = em_phy_reset(hw); - if (ret_val) { - DEBUGOUT("Error Resetting the PHY\n"); - return ret_val; - } - - /* Wait 15ms for MAC to configure PHY from eeprom settings */ - msec_delay(15); - if (hw->mac_type != em_ich8lan) { - /* Configure activity LED after PHY reset */ - led_ctrl = E1000_READ_REG(hw, LEDCTL); - led_ctrl &= IGP_ACTIVITY_LED_MASK; - led_ctrl |= (IGP_ACTIVITY_LED_ENABLE | IGP_LED3_MODE); - E1000_WRITE_REG(hw, LEDCTL, led_ctrl); - } - - /* The NVM settings will configure LPLU in D3 for IGP2 and IGP3 PHYs */ - if (hw->phy_type == em_phy_igp) { - /* disable lplu d3 during driver init */ - ret_val = em_set_d3_lplu_state(hw, FALSE); - if (ret_val) { - DEBUGOUT("Error Disabling LPLU D3\n"); - return ret_val; - } - } - - /* disable lplu d0 during driver init */ - ret_val = em_set_d0_lplu_state(hw, FALSE); - if (ret_val) { - DEBUGOUT("Error Disabling LPLU D0\n"); - return ret_val; - } - /* Configure mdi-mdix settings */ - ret_val = em_read_phy_reg(hw, IGP01E1000_PHY_PORT_CTRL, &phy_data); - if (ret_val) - return ret_val; - - if ((hw->mac_type == em_82541) || (hw->mac_type == em_82547)) { - hw->dsp_config_state = em_dsp_config_disabled; - /* Force MDI for earlier revs of the IGP PHY */ - phy_data &= ~(IGP01E1000_PSCR_AUTO_MDIX | IGP01E1000_PSCR_FORCE_MDI_MDIX); - hw->mdix = 1; - - } else { - hw->dsp_config_state = em_dsp_config_enabled; - phy_data &= ~IGP01E1000_PSCR_AUTO_MDIX; - - switch (hw->mdix) { - case 1: - phy_data &= ~IGP01E1000_PSCR_FORCE_MDI_MDIX; - break; - case 2: - phy_data |= IGP01E1000_PSCR_FORCE_MDI_MDIX; - break; - case 0: - default: - phy_data |= IGP01E1000_PSCR_AUTO_MDIX; - break; - } - } - ret_val = em_write_phy_reg(hw, IGP01E1000_PHY_PORT_CTRL, phy_data); - if (ret_val) - return ret_val; - - /* set auto-master slave resolution settings */ - if (hw->autoneg) { - em_ms_type phy_ms_setting = hw->master_slave; - - if (hw->ffe_config_state == em_ffe_config_active) - hw->ffe_config_state = em_ffe_config_enabled; - - if (hw->dsp_config_state == em_dsp_config_activated) - hw->dsp_config_state = em_dsp_config_enabled; - - /* when autonegotiation advertisment is only 1000Mbps then we - * should disable SmartSpeed and enable Auto MasterSlave - * resolution as hardware default. */ - if (hw->autoneg_advertised == ADVERTISE_1000_FULL) { - /* Disable SmartSpeed */ - ret_val = em_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, - &phy_data); - if (ret_val) - return ret_val; - phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED; - ret_val = em_write_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, - phy_data); - if (ret_val) - return ret_val; - /* Set auto Master/Slave resolution process */ - ret_val = em_read_phy_reg(hw, PHY_1000T_CTRL, &phy_data); - if (ret_val) - return ret_val; - phy_data &= ~CR_1000T_MS_ENABLE; - ret_val = em_write_phy_reg(hw, PHY_1000T_CTRL, phy_data); - if (ret_val) - return ret_val; - } - - ret_val = em_read_phy_reg(hw, PHY_1000T_CTRL, &phy_data); - if (ret_val) - return ret_val; - - /* load defaults for future use */ - hw->original_master_slave = (phy_data & CR_1000T_MS_ENABLE) ? - ((phy_data & CR_1000T_MS_VALUE) ? - em_ms_force_master : - em_ms_force_slave) : - em_ms_auto; - - switch (phy_ms_setting) { - case em_ms_force_master: - phy_data |= (CR_1000T_MS_ENABLE | CR_1000T_MS_VALUE); - break; - case em_ms_force_slave: - phy_data |= CR_1000T_MS_ENABLE; - phy_data &= ~(CR_1000T_MS_VALUE); - break; - case em_ms_auto: - phy_data &= ~CR_1000T_MS_ENABLE; - default: - break; - } - ret_val = em_write_phy_reg(hw, PHY_1000T_CTRL, phy_data); - if (ret_val) - return ret_val; - } - - return E1000_SUCCESS; -} - -/******************************************************************** -* Copper link setup for em_phy_gg82563 series. -* -* hw - Struct containing variables accessed by shared code -*********************************************************************/ -static int32_t -em_copper_link_ggp_setup(struct em_hw *hw) -{ - int32_t ret_val; - uint16_t phy_data; - uint32_t reg_data; - - DEBUGFUNC("em_copper_link_ggp_setup"); - - if (!hw->phy_reset_disable) { - - /* Enable CRS on TX for half-duplex operation. */ - ret_val = em_read_phy_reg(hw, GG82563_PHY_MAC_SPEC_CTRL, - &phy_data); - if (ret_val) - return ret_val; - - phy_data |= GG82563_MSCR_ASSERT_CRS_ON_TX; - /* Use 25MHz for both link down and 1000BASE-T for Tx clock */ - phy_data |= GG82563_MSCR_TX_CLK_1000MBPS_25MHZ; - - ret_val = em_write_phy_reg(hw, GG82563_PHY_MAC_SPEC_CTRL, - phy_data); - if (ret_val) - return ret_val; - - /* Options: - * MDI/MDI-X = 0 (default) - * 0 - Auto for all speeds - * 1 - MDI mode - * 2 - MDI-X mode - * 3 - Auto for 1000Base-T only (MDI-X for 10/100Base-T modes) - */ - ret_val = em_read_phy_reg(hw, GG82563_PHY_SPEC_CTRL, &phy_data); - if (ret_val) - return ret_val; - - phy_data &= ~GG82563_PSCR_CROSSOVER_MODE_MASK; - - switch (hw->mdix) { - case 1: - phy_data |= GG82563_PSCR_CROSSOVER_MODE_MDI; - break; - case 2: - phy_data |= GG82563_PSCR_CROSSOVER_MODE_MDIX; - break; - case 0: - default: - phy_data |= GG82563_PSCR_CROSSOVER_MODE_AUTO; - break; - } - - /* Options: - * disable_polarity_correction = 0 (default) - * Automatic Correction for Reversed Cable Polarity - * 0 - Disabled - * 1 - Enabled - */ - phy_data &= ~GG82563_PSCR_POLARITY_REVERSAL_DISABLE; - if (hw->disable_polarity_correction == 1) - phy_data |= GG82563_PSCR_POLARITY_REVERSAL_DISABLE; - ret_val = em_write_phy_reg(hw, GG82563_PHY_SPEC_CTRL, phy_data); - - if (ret_val) - return ret_val; - - /* SW Reset the PHY so all changes take effect */ - ret_val = em_phy_reset(hw); - if (ret_val) { - DEBUGOUT("Error Resetting the PHY\n"); - return ret_val; - } - } /* phy_reset_disable */ - - if (hw->mac_type == em_80003es2lan) { - /* Bypass RX and TX FIFO's */ - ret_val = em_write_kmrn_reg(hw, E1000_KUMCTRLSTA_OFFSET_FIFO_CTRL, - E1000_KUMCTRLSTA_FIFO_CTRL_RX_BYPASS | - E1000_KUMCTRLSTA_FIFO_CTRL_TX_BYPASS); - if (ret_val) - return ret_val; - - ret_val = em_read_phy_reg(hw, GG82563_PHY_SPEC_CTRL_2, &phy_data); - if (ret_val) - return ret_val; - - phy_data &= ~GG82563_PSCR2_REVERSE_AUTO_NEG; - ret_val = em_write_phy_reg(hw, GG82563_PHY_SPEC_CTRL_2, phy_data); - - if (ret_val) - return ret_val; - - reg_data = E1000_READ_REG(hw, CTRL_EXT); - reg_data &= ~(E1000_CTRL_EXT_LINK_MODE_MASK); - E1000_WRITE_REG(hw, CTRL_EXT, reg_data); - - ret_val = em_read_phy_reg(hw, GG82563_PHY_PWR_MGMT_CTRL, - &phy_data); - if (ret_val) - return ret_val; - - /* Do not init these registers when the HW is in IAMT mode, since the - * firmware will have already initialized them. We only initialize - * them if the HW is not in IAMT mode. - */ - if (em_check_mng_mode(hw) == FALSE) { - /* Enable Electrical Idle on the PHY */ - phy_data |= GG82563_PMCR_ENABLE_ELECTRICAL_IDLE; - ret_val = em_write_phy_reg(hw, GG82563_PHY_PWR_MGMT_CTRL, - phy_data); - if (ret_val) - return ret_val; - - ret_val = em_read_phy_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, - &phy_data); - if (ret_val) - return ret_val; - - phy_data &= ~GG82563_KMCR_PASS_FALSE_CARRIER; - ret_val = em_write_phy_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, - phy_data); - - if (ret_val) - return ret_val; - } - - /* Workaround: Disable padding in Kumeran interface in the MAC - * and in the PHY to avoid CRC errors. - */ - ret_val = em_read_phy_reg(hw, GG82563_PHY_INBAND_CTRL, - &phy_data); - if (ret_val) - return ret_val; - phy_data |= GG82563_ICR_DIS_PADDING; - ret_val = em_write_phy_reg(hw, GG82563_PHY_INBAND_CTRL, - phy_data); - if (ret_val) - return ret_val; - } - - return E1000_SUCCESS; -} - -/******************************************************************** -* Copper link setup for em_phy_m88 series. -* -* hw - Struct containing variables accessed by shared code -*********************************************************************/ -static int32_t -em_copper_link_mgp_setup(struct em_hw *hw) -{ - int32_t ret_val; - uint16_t phy_data; - - DEBUGFUNC("em_copper_link_mgp_setup"); - - if (hw->phy_reset_disable) - return E1000_SUCCESS; - - /* Enable CRS on TX. This must be set for half-duplex operation. */ - ret_val = em_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data); - if (ret_val) - return ret_val; - - phy_data |= M88E1000_PSCR_ASSERT_CRS_ON_TX; - - /* Options: - * MDI/MDI-X = 0 (default) - * 0 - Auto for all speeds - * 1 - MDI mode - * 2 - MDI-X mode - * 3 - Auto for 1000Base-T only (MDI-X for 10/100Base-T modes) - */ - phy_data &= ~M88E1000_PSCR_AUTO_X_MODE; - - switch (hw->mdix) { - case 1: - phy_data |= M88E1000_PSCR_MDI_MANUAL_MODE; - break; - case 2: - phy_data |= M88E1000_PSCR_MDIX_MANUAL_MODE; - break; - case 3: - phy_data |= M88E1000_PSCR_AUTO_X_1000T; - break; - case 0: - default: - phy_data |= M88E1000_PSCR_AUTO_X_MODE; - break; - } - - /* Options: - * disable_polarity_correction = 0 (default) - * Automatic Correction for Reversed Cable Polarity - * 0 - Disabled - * 1 - Enabled - */ - phy_data &= ~M88E1000_PSCR_POLARITY_REVERSAL; - if (hw->disable_polarity_correction == 1) - phy_data |= M88E1000_PSCR_POLARITY_REVERSAL; - ret_val = em_write_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, phy_data); - if (ret_val) - return ret_val; - - if (hw->phy_revision < M88E1011_I_REV_4) { - /* Force TX_CLK in the Extended PHY Specific Control Register - * to 25MHz clock. - */ - ret_val = em_read_phy_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL, &phy_data); - if (ret_val) - return ret_val; - - phy_data |= M88E1000_EPSCR_TX_CLK_25; - - if ((hw->phy_revision == E1000_REVISION_2) && - (hw->phy_id == M88E1111_I_PHY_ID)) { - /* Vidalia Phy, set the downshift counter to 5x */ - phy_data &= ~(M88EC018_EPSCR_DOWNSHIFT_COUNTER_MASK); - phy_data |= M88EC018_EPSCR_DOWNSHIFT_COUNTER_5X; - ret_val = em_write_phy_reg(hw, - M88E1000_EXT_PHY_SPEC_CTRL, phy_data); - if (ret_val) - return ret_val; - } else { - /* Configure Master and Slave downshift values */ - phy_data &= ~(M88E1000_EPSCR_MASTER_DOWNSHIFT_MASK | - M88E1000_EPSCR_SLAVE_DOWNSHIFT_MASK); - phy_data |= (M88E1000_EPSCR_MASTER_DOWNSHIFT_1X | - M88E1000_EPSCR_SLAVE_DOWNSHIFT_1X); - ret_val = em_write_phy_reg(hw, - M88E1000_EXT_PHY_SPEC_CTRL, phy_data); - if (ret_val) - return ret_val; - } - } - - /* SW Reset the PHY so all changes take effect */ - ret_val = em_phy_reset(hw); - if (ret_val) { - DEBUGOUT("Error Resetting the PHY\n"); - return ret_val; - } - - return E1000_SUCCESS; -} - -/******************************************************************** -* Setup auto-negotiation and flow control advertisements, -* and then perform auto-negotiation. -* -* hw - Struct containing variables accessed by shared code -*********************************************************************/ -static int32_t -em_copper_link_autoneg(struct em_hw *hw) -{ - int32_t ret_val; - uint16_t phy_data; - - DEBUGFUNC("em_copper_link_autoneg"); - - /* Perform some bounds checking on the hw->autoneg_advertised - * parameter. If this variable is zero, then set it to the default. - */ - hw->autoneg_advertised &= AUTONEG_ADVERTISE_SPEED_DEFAULT; - - /* If autoneg_advertised is zero, we assume it was not defaulted - * by the calling code so we set to advertise full capability. - */ - if (hw->autoneg_advertised == 0) - hw->autoneg_advertised = AUTONEG_ADVERTISE_SPEED_DEFAULT; - - /* IFE phy only supports 10/100 */ - if (hw->phy_type == em_phy_ife) - hw->autoneg_advertised &= AUTONEG_ADVERTISE_10_100_ALL; - - DEBUGOUT("Reconfiguring auto-neg advertisement params\n"); - ret_val = em_phy_setup_autoneg(hw); - if (ret_val) { - DEBUGOUT("Error Setting up Auto-Negotiation\n"); - return ret_val; - } - DEBUGOUT("Restarting Auto-Neg\n"); - - /* Restart auto-negotiation by setting the Auto Neg Enable bit and - * the Auto Neg Restart bit in the PHY control register. - */ - ret_val = em_read_phy_reg(hw, PHY_CTRL, &phy_data); - if (ret_val) - return ret_val; - - phy_data |= (MII_CR_AUTO_NEG_EN | MII_CR_RESTART_AUTO_NEG); - ret_val = em_write_phy_reg(hw, PHY_CTRL, phy_data); - if (ret_val) - return ret_val; - - /* Does the user want to wait for Auto-Neg to complete here, or - * check at a later time (for example, callback routine). - */ - if (hw->wait_autoneg_complete) { - ret_val = em_wait_autoneg(hw); - if (ret_val) { - DEBUGOUT("Error while waiting for autoneg to complete\n"); - return ret_val; - } - } - - hw->get_link_status = TRUE; - - return E1000_SUCCESS; -} - -/****************************************************************************** -* Config the MAC and the PHY after link is up. -* 1) Set up the MAC to the current PHY speed/duplex -* if we are on 82543. If we -* are on newer silicon, we only need to configure -* collision distance in the Transmit Control Register. -* 2) Set up flow control on the MAC to that established with -* the link partner. -* 3) Config DSP to improve Gigabit link quality for some PHY revisions. -* -* hw - Struct containing variables accessed by shared code -******************************************************************************/ -static int32_t -em_copper_link_postconfig(struct em_hw *hw) -{ - int32_t ret_val; - DEBUGFUNC("em_copper_link_postconfig"); - - if (hw->mac_type >= em_82544) { - em_config_collision_dist(hw); - } else { - ret_val = em_config_mac_to_phy(hw); - if (ret_val) { - DEBUGOUT("Error configuring MAC to PHY settings\n"); - return ret_val; - } - } - ret_val = em_config_fc_after_link_up(hw); - if (ret_val) { - DEBUGOUT("Error Configuring Flow Control\n"); - return ret_val; - } - - /* Config DSP to improve Giga link quality */ - if (hw->phy_type == em_phy_igp) { - ret_val = em_config_dsp_after_link_change(hw, TRUE); - if (ret_val) { - DEBUGOUT("Error Configuring DSP after link up\n"); - return ret_val; - } - } - - return E1000_SUCCESS; -} - -/****************************************************************************** -* Detects which PHY is present and setup the speed and duplex -* -* hw - Struct containing variables accessed by shared code -******************************************************************************/ -static int32_t -em_setup_copper_link(struct em_hw *hw) -{ - int32_t ret_val; - uint16_t i; - uint16_t phy_data; - uint16_t reg_data; - - DEBUGFUNC("em_setup_copper_link"); - - switch (hw->mac_type) { - case em_80003es2lan: - case em_ich8lan: - case em_ich9lan: - /* Set the mac to wait the maximum time between each - * iteration and increase the max iterations when - * polling the phy; this fixes erroneous timeouts at 10Mbps. */ - ret_val = em_write_kmrn_reg(hw, GG82563_REG(0x34, 4), 0xFFFF); - if (ret_val) - return ret_val; - ret_val = em_read_kmrn_reg(hw, GG82563_REG(0x34, 9), ®_data); - if (ret_val) - return ret_val; - reg_data |= 0x3F; - ret_val = em_write_kmrn_reg(hw, GG82563_REG(0x34, 9), reg_data); - if (ret_val) - return ret_val; - default: - break; - } - - /* Check if it is a valid PHY and set PHY mode if necessary. */ - ret_val = em_copper_link_preconfig(hw); - if (ret_val) - return ret_val; - - switch (hw->mac_type) { - case em_80003es2lan: - /* Kumeran registers are written-only */ - reg_data = E1000_KUMCTRLSTA_INB_CTRL_LINK_STATUS_TX_TIMEOUT_DEFAULT; - reg_data |= E1000_KUMCTRLSTA_INB_CTRL_DIS_PADDING; - ret_val = em_write_kmrn_reg(hw, E1000_KUMCTRLSTA_OFFSET_INB_CTRL, - reg_data); - if (ret_val) - return ret_val; - break; - default: - break; - } - - if (hw->phy_type == em_phy_igp || - hw->phy_type == em_phy_igp_3 || - hw->phy_type == em_phy_igp_2) { - ret_val = em_copper_link_igp_setup(hw); - if (ret_val) - return ret_val; - } else if (hw->phy_type == em_phy_m88) { - ret_val = em_copper_link_mgp_setup(hw); - if (ret_val) - return ret_val; - } else if (hw->phy_type == em_phy_gg82563) { - ret_val = em_copper_link_ggp_setup(hw); - if (ret_val) - return ret_val; - } - - if (hw->autoneg) { - /* Setup autoneg and flow control advertisement - * and perform autonegotiation */ - ret_val = em_copper_link_autoneg(hw); - if (ret_val) - return ret_val; - } else { - /* PHY will be set to 10H, 10F, 100H,or 100F - * depending on value from forced_speed_duplex. */ - DEBUGOUT("Forcing speed and duplex\n"); - ret_val = em_phy_force_speed_duplex(hw); - if (ret_val) { - DEBUGOUT("Error Forcing Speed and Duplex\n"); - return ret_val; - } - } - - /* Check link status. Wait up to 100 microseconds for link to become - * valid. - */ - for (i = 0; i < 10; i++) { - ret_val = em_read_phy_reg(hw, PHY_STATUS, &phy_data); - if (ret_val) - return ret_val; - ret_val = em_read_phy_reg(hw, PHY_STATUS, &phy_data); - if (ret_val) - return ret_val; - - if (phy_data & MII_SR_LINK_STATUS) { - /* Config the MAC and PHY after link is up */ - ret_val = em_copper_link_postconfig(hw); - if (ret_val) - return ret_val; - - DEBUGOUT("Valid link established!!!\n"); - return E1000_SUCCESS; - } - usec_delay(10); - } - - DEBUGOUT("Unable to establish link!!!\n"); - return E1000_SUCCESS; -} - -/****************************************************************************** -* Configure the MAC-to-PHY interface for 10/100Mbps -* -* hw - Struct containing variables accessed by shared code -******************************************************************************/ -static int32_t -em_configure_kmrn_for_10_100(struct em_hw *hw, uint16_t duplex) -{ - int32_t ret_val = E1000_SUCCESS; - uint32_t tipg; - uint16_t reg_data; - - DEBUGFUNC("em_configure_kmrn_for_10_100"); - - reg_data = E1000_KUMCTRLSTA_HD_CTRL_10_100_DEFAULT; - ret_val = em_write_kmrn_reg(hw, E1000_KUMCTRLSTA_OFFSET_HD_CTRL, - reg_data); - if (ret_val) - return ret_val; - - /* Configure Transmit Inter-Packet Gap */ - tipg = E1000_READ_REG(hw, TIPG); - tipg &= ~E1000_TIPG_IPGT_MASK; - tipg |= DEFAULT_80003ES2LAN_TIPG_IPGT_10_100; - E1000_WRITE_REG(hw, TIPG, tipg); - - ret_val = em_read_phy_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, ®_data); - - if (ret_val) - return ret_val; - - if (duplex == HALF_DUPLEX) - reg_data |= GG82563_KMCR_PASS_FALSE_CARRIER; - else - reg_data &= ~GG82563_KMCR_PASS_FALSE_CARRIER; - - ret_val = em_write_phy_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, reg_data); - - return ret_val; -} - -static int32_t -em_configure_kmrn_for_1000(struct em_hw *hw) -{ - int32_t ret_val = E1000_SUCCESS; - uint16_t reg_data; - uint32_t tipg; - - DEBUGFUNC("em_configure_kmrn_for_1000"); - - reg_data = E1000_KUMCTRLSTA_HD_CTRL_1000_DEFAULT; - ret_val = em_write_kmrn_reg(hw, E1000_KUMCTRLSTA_OFFSET_HD_CTRL, - reg_data); - if (ret_val) - return ret_val; - - /* Configure Transmit Inter-Packet Gap */ - tipg = E1000_READ_REG(hw, TIPG); - tipg &= ~E1000_TIPG_IPGT_MASK; - tipg |= DEFAULT_80003ES2LAN_TIPG_IPGT_1000; - E1000_WRITE_REG(hw, TIPG, tipg); - - ret_val = em_read_phy_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, ®_data); - - if (ret_val) - return ret_val; - - reg_data &= ~GG82563_KMCR_PASS_FALSE_CARRIER; - ret_val = em_write_phy_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, reg_data); - - return ret_val; -} - -/****************************************************************************** -* Configures PHY autoneg and flow control advertisement settings -* -* hw - Struct containing variables accessed by shared code -******************************************************************************/ -int32_t -em_phy_setup_autoneg(struct em_hw *hw) -{ - int32_t ret_val; - uint16_t mii_autoneg_adv_reg; - uint16_t mii_1000t_ctrl_reg; - - DEBUGFUNC("em_phy_setup_autoneg"); - - /* Read the MII Auto-Neg Advertisement Register (Address 4). */ - ret_val = em_read_phy_reg(hw, PHY_AUTONEG_ADV, &mii_autoneg_adv_reg); - if (ret_val) - return ret_val; - - if (hw->phy_type != em_phy_ife) { - /* Read the MII 1000Base-T Control Register (Address 9). */ - ret_val = em_read_phy_reg(hw, PHY_1000T_CTRL, &mii_1000t_ctrl_reg); - if (ret_val) - return ret_val; - } else - mii_1000t_ctrl_reg=0; - - /* Need to parse both autoneg_advertised and fc and set up - * the appropriate PHY registers. First we will parse for - * autoneg_advertised software override. Since we can advertise - * a plethora of combinations, we need to check each bit - * individually. - */ - - /* First we clear all the 10/100 mb speed bits in the Auto-Neg - * Advertisement Register (Address 4) and the 1000 mb speed bits in - * the 1000Base-T Control Register (Address 9). - */ - mii_autoneg_adv_reg &= ~REG4_SPEED_MASK; - mii_1000t_ctrl_reg &= ~REG9_SPEED_MASK; - - DEBUGOUT1("autoneg_advertised %x\n", hw->autoneg_advertised); - - /* Do we want to advertise 10 Mb Half Duplex? */ - if (hw->autoneg_advertised & ADVERTISE_10_HALF) { - DEBUGOUT("Advertise 10mb Half duplex\n"); - mii_autoneg_adv_reg |= NWAY_AR_10T_HD_CAPS; - } - - /* Do we want to advertise 10 Mb Full Duplex? */ - if (hw->autoneg_advertised & ADVERTISE_10_FULL) { - DEBUGOUT("Advertise 10mb Full duplex\n"); - mii_autoneg_adv_reg |= NWAY_AR_10T_FD_CAPS; - } - - /* Do we want to advertise 100 Mb Half Duplex? */ - if (hw->autoneg_advertised & ADVERTISE_100_HALF) { - DEBUGOUT("Advertise 100mb Half duplex\n"); - mii_autoneg_adv_reg |= NWAY_AR_100TX_HD_CAPS; - } - - /* Do we want to advertise 100 Mb Full Duplex? */ - if (hw->autoneg_advertised & ADVERTISE_100_FULL) { - DEBUGOUT("Advertise 100mb Full duplex\n"); - mii_autoneg_adv_reg |= NWAY_AR_100TX_FD_CAPS; - } - - /* We do not allow the Phy to advertise 1000 Mb Half Duplex */ - if (hw->autoneg_advertised & ADVERTISE_1000_HALF) { - DEBUGOUT("Advertise 1000mb Half duplex requested, request denied!\n"); - } - - /* Do we want to advertise 1000 Mb Full Duplex? */ - if (hw->autoneg_advertised & ADVERTISE_1000_FULL) { - DEBUGOUT("Advertise 1000mb Full duplex\n"); - mii_1000t_ctrl_reg |= CR_1000T_FD_CAPS; - if (hw->phy_type == em_phy_ife) { - DEBUGOUT("em_phy_ife is a 10/100 PHY. Gigabit speed is not supported.\n"); - } - } - - /* Check for a software override of the flow control settings, and - * setup the PHY advertisement registers accordingly. If - * auto-negotiation is enabled, then software will have to set the - * "PAUSE" bits to the correct value in the Auto-Negotiation - * Advertisement Register (PHY_AUTONEG_ADV) and re-start auto-negotiation. - * - * The possible values of the "fc" parameter are: - * 0: Flow control is completely disabled - * 1: Rx flow control is enabled (we can receive pause frames - * but not send pause frames). - * 2: Tx flow control is enabled (we can send pause frames - * but we do not support receiving pause frames). - * 3: Both Rx and TX flow control (symmetric) are enabled. - * other: No software override. The flow control configuration - * in the EEPROM is used. - */ - switch (hw->fc) { - case E1000_FC_NONE: /* 0 */ - /* Flow control (RX & TX) is completely disabled by a - * software over-ride. - */ - mii_autoneg_adv_reg &= ~(NWAY_AR_ASM_DIR | NWAY_AR_PAUSE); - break; - case E1000_FC_RX_PAUSE: /* 1 */ - /* RX Flow control is enabled, and TX Flow control is - * disabled, by a software over-ride. - */ - /* Since there really isn't a way to advertise that we are - * capable of RX Pause ONLY, we will advertise that we - * support both symmetric and asymmetric RX PAUSE. Later - * (in em_config_fc_after_link_up) we will disable the - *hw's ability to send PAUSE frames. - */ - mii_autoneg_adv_reg |= (NWAY_AR_ASM_DIR | NWAY_AR_PAUSE); - break; - case E1000_FC_TX_PAUSE: /* 2 */ - /* TX Flow control is enabled, and RX Flow control is - * disabled, by a software over-ride. - */ - mii_autoneg_adv_reg |= NWAY_AR_ASM_DIR; - mii_autoneg_adv_reg &= ~NWAY_AR_PAUSE; - break; - case E1000_FC_FULL: /* 3 */ - /* Flow control (both RX and TX) is enabled by a software - * over-ride. - */ - mii_autoneg_adv_reg |= (NWAY_AR_ASM_DIR | NWAY_AR_PAUSE); - break; - default: - DEBUGOUT("Flow control param set incorrectly\n"); - return -E1000_ERR_CONFIG; - } - - ret_val = em_write_phy_reg(hw, PHY_AUTONEG_ADV, mii_autoneg_adv_reg); - if (ret_val) - return ret_val; - - DEBUGOUT1("Auto-Neg Advertising %x\n", mii_autoneg_adv_reg); - - if (hw->phy_type != em_phy_ife) { - ret_val = em_write_phy_reg(hw, PHY_1000T_CTRL, mii_1000t_ctrl_reg); - if (ret_val) - return ret_val; - } - - return E1000_SUCCESS; -} - -/****************************************************************************** -* Force PHY speed and duplex settings to hw->forced_speed_duplex -* -* hw - Struct containing variables accessed by shared code -******************************************************************************/ -static int32_t -em_phy_force_speed_duplex(struct em_hw *hw) -{ - uint32_t ctrl; - int32_t ret_val; - uint16_t mii_ctrl_reg; - uint16_t mii_status_reg; - uint16_t phy_data; - uint16_t i; - - DEBUGFUNC("em_phy_force_speed_duplex"); - - /* Turn off Flow control if we are forcing speed and duplex. */ - hw->fc = E1000_FC_NONE; - - DEBUGOUT1("hw->fc = %d\n", hw->fc); - - /* Read the Device Control Register. */ - ctrl = E1000_READ_REG(hw, CTRL); - - /* Set the bits to Force Speed and Duplex in the Device Ctrl Reg. */ - ctrl |= (E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX); - ctrl &= ~(DEVICE_SPEED_MASK); - - /* Clear the Auto Speed Detect Enable bit. */ - ctrl &= ~E1000_CTRL_ASDE; - - /* Read the MII Control Register. */ - ret_val = em_read_phy_reg(hw, PHY_CTRL, &mii_ctrl_reg); - if (ret_val) - return ret_val; - - /* We need to disable autoneg in order to force link and duplex. */ - - mii_ctrl_reg &= ~MII_CR_AUTO_NEG_EN; - - /* Are we forcing Full or Half Duplex? */ - if (hw->forced_speed_duplex == em_100_full || - hw->forced_speed_duplex == em_10_full) { - /* We want to force full duplex so we SET the full duplex bits in the - * Device and MII Control Registers. - */ - ctrl |= E1000_CTRL_FD; - mii_ctrl_reg |= MII_CR_FULL_DUPLEX; - DEBUGOUT("Full Duplex\n"); - } else { - /* We want to force half duplex so we CLEAR the full duplex bits in - * the Device and MII Control Registers. - */ - ctrl &= ~E1000_CTRL_FD; - mii_ctrl_reg &= ~MII_CR_FULL_DUPLEX; - DEBUGOUT("Half Duplex\n"); - } - - /* Are we forcing 100Mbps??? */ - if (hw->forced_speed_duplex == em_100_full || - hw->forced_speed_duplex == em_100_half) { - /* Set the 100Mb bit and turn off the 1000Mb and 10Mb bits. */ - ctrl |= E1000_CTRL_SPD_100; - mii_ctrl_reg |= MII_CR_SPEED_100; - mii_ctrl_reg &= ~(MII_CR_SPEED_1000 | MII_CR_SPEED_10); - DEBUGOUT("Forcing 100mb "); - } else { - /* Set the 10Mb bit and turn off the 1000Mb and 100Mb bits. */ - ctrl &= ~(E1000_CTRL_SPD_1000 | E1000_CTRL_SPD_100); - mii_ctrl_reg |= MII_CR_SPEED_10; - mii_ctrl_reg &= ~(MII_CR_SPEED_1000 | MII_CR_SPEED_100); - DEBUGOUT("Forcing 10mb "); - } - - em_config_collision_dist(hw); - - /* Write the configured values back to the Device Control Reg. */ - E1000_WRITE_REG(hw, CTRL, ctrl); - - if ((hw->phy_type == em_phy_m88) || - (hw->phy_type == em_phy_gg82563)) { - ret_val = em_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data); - if (ret_val) - return ret_val; - - /* Clear Auto-Crossover to force MDI manually. M88E1000 requires MDI - * forced whenever speed are duplex are forced. - */ - phy_data &= ~M88E1000_PSCR_AUTO_X_MODE; - ret_val = em_write_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, phy_data); - if (ret_val) - return ret_val; - - DEBUGOUT1("M88E1000 PSCR: %x \n", phy_data); - - /* Need to reset the PHY or these changes will be ignored */ - mii_ctrl_reg |= MII_CR_RESET; - - /* Disable MDI-X support for 10/100 */ - } else if (hw->phy_type == em_phy_ife) { - ret_val = em_read_phy_reg(hw, IFE_PHY_MDIX_CONTROL, &phy_data); - if (ret_val) - return ret_val; - - phy_data &= ~IFE_PMC_AUTO_MDIX; - phy_data &= ~IFE_PMC_FORCE_MDIX; - - ret_val = em_write_phy_reg(hw, IFE_PHY_MDIX_CONTROL, phy_data); - if (ret_val) - return ret_val; - - } else { - /* Clear Auto-Crossover to force MDI manually. IGP requires MDI - * forced whenever speed or duplex are forced. - */ - ret_val = em_read_phy_reg(hw, IGP01E1000_PHY_PORT_CTRL, &phy_data); - if (ret_val) - return ret_val; - - phy_data &= ~IGP01E1000_PSCR_AUTO_MDIX; - phy_data &= ~IGP01E1000_PSCR_FORCE_MDI_MDIX; - - ret_val = em_write_phy_reg(hw, IGP01E1000_PHY_PORT_CTRL, phy_data); - if (ret_val) - return ret_val; - } - - /* Write back the modified PHY MII control register. */ - ret_val = em_write_phy_reg(hw, PHY_CTRL, mii_ctrl_reg); - if (ret_val) - return ret_val; - - usec_delay(1); - - /* The wait_autoneg_complete flag may be a little misleading here. - * Since we are forcing speed and duplex, Auto-Neg is not enabled. - * But we do want to delay for a period while forcing only so we - * don't generate false No Link messages. So we will wait here - * only if the user has set wait_autoneg_complete to 1, which is - * the default. - */ - if (hw->wait_autoneg_complete) { - /* We will wait for autoneg to complete. */ - DEBUGOUT("Waiting for forced speed/duplex link.\n"); - mii_status_reg = 0; - - /* We will wait for autoneg to complete or 4.5 seconds to expire. */ - for (i = PHY_FORCE_TIME; i > 0; i--) { - /* Read the MII Status Register and wait for Auto-Neg Complete bit - * to be set. - */ - ret_val = em_read_phy_reg(hw, PHY_STATUS, &mii_status_reg); - if (ret_val) - return ret_val; - - ret_val = em_read_phy_reg(hw, PHY_STATUS, &mii_status_reg); - if (ret_val) - return ret_val; - - if (mii_status_reg & MII_SR_LINK_STATUS) break; - msec_delay(100); - } - if ((i == 0) && - ((hw->phy_type == em_phy_m88) || - (hw->phy_type == em_phy_gg82563))) { - /* We didn't get link. Reset the DSP and wait again for link. */ - ret_val = em_phy_reset_dsp(hw); - if (ret_val) { - DEBUGOUT("Error Resetting PHY DSP\n"); - return ret_val; - } - } - /* This loop will early-out if the link condition has been met. */ - for (i = PHY_FORCE_TIME; i > 0; i--) { - if (mii_status_reg & MII_SR_LINK_STATUS) break; - msec_delay(100); - /* Read the MII Status Register and wait for Auto-Neg Complete bit - * to be set. - */ - ret_val = em_read_phy_reg(hw, PHY_STATUS, &mii_status_reg); - if (ret_val) - return ret_val; - - ret_val = em_read_phy_reg(hw, PHY_STATUS, &mii_status_reg); - if (ret_val) - return ret_val; - } - } - - if (hw->phy_type == em_phy_m88) { - /* Because we reset the PHY above, we need to re-force TX_CLK in the - * Extended PHY Specific Control Register to 25MHz clock. This value - * defaults back to a 2.5MHz clock when the PHY is reset. - */ - ret_val = em_read_phy_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL, &phy_data); - if (ret_val) - return ret_val; - - phy_data |= M88E1000_EPSCR_TX_CLK_25; - ret_val = em_write_phy_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL, phy_data); - if (ret_val) - return ret_val; - - /* In addition, because of the s/w reset above, we need to enable CRS on - * TX. This must be set for both full and half duplex operation. - */ - ret_val = em_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data); - if (ret_val) - return ret_val; - - phy_data |= M88E1000_PSCR_ASSERT_CRS_ON_TX; - ret_val = em_write_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, phy_data); - if (ret_val) - return ret_val; - - if ((hw->mac_type == em_82544 || hw->mac_type == em_82543) && - (!hw->autoneg) && (hw->forced_speed_duplex == em_10_full || - hw->forced_speed_duplex == em_10_half)) { - ret_val = em_polarity_reversal_workaround(hw); - if (ret_val) - return ret_val; - } - } else if (hw->phy_type == em_phy_gg82563) { - /* The TX_CLK of the Extended PHY Specific Control Register defaults - * to 2.5MHz on a reset. We need to re-force it back to 25MHz, if - * we're not in a forced 10/duplex configuration. */ - ret_val = em_read_phy_reg(hw, GG82563_PHY_MAC_SPEC_CTRL, &phy_data); - if (ret_val) - return ret_val; - - phy_data &= ~GG82563_MSCR_TX_CLK_MASK; - if ((hw->forced_speed_duplex == em_10_full) || - (hw->forced_speed_duplex == em_10_half)) - phy_data |= GG82563_MSCR_TX_CLK_10MBPS_2_5MHZ; - else - phy_data |= GG82563_MSCR_TX_CLK_100MBPS_25MHZ; - - /* Also due to the reset, we need to enable CRS on Tx. */ - phy_data |= GG82563_MSCR_ASSERT_CRS_ON_TX; - - ret_val = em_write_phy_reg(hw, GG82563_PHY_MAC_SPEC_CTRL, phy_data); - if (ret_val) - return ret_val; - } - return E1000_SUCCESS; -} - -/****************************************************************************** -* Sets the collision distance in the Transmit Control register -* -* hw - Struct containing variables accessed by shared code -* -* Link should have been established previously. Reads the speed and duplex -* information from the Device Status register. -******************************************************************************/ -void -em_config_collision_dist(struct em_hw *hw) -{ - uint32_t tctl, coll_dist; - - DEBUGFUNC("em_config_collision_dist"); - - if (hw->mac_type < em_82543) - coll_dist = E1000_COLLISION_DISTANCE_82542; - else - coll_dist = E1000_COLLISION_DISTANCE; - - tctl = E1000_READ_REG(hw, TCTL); - - tctl &= ~E1000_TCTL_COLD; - tctl |= coll_dist << E1000_COLD_SHIFT; - - E1000_WRITE_REG(hw, TCTL, tctl); - E1000_WRITE_FLUSH(hw); -} - -/****************************************************************************** -* Sets MAC speed and duplex settings to reflect the those in the PHY -* -* hw - Struct containing variables accessed by shared code -* mii_reg - data to write to the MII control register -* -* The contents of the PHY register containing the needed information need to -* be passed in. -******************************************************************************/ -static int32_t -em_config_mac_to_phy(struct em_hw *hw) -{ - uint32_t ctrl; - int32_t ret_val; - uint16_t phy_data; - - DEBUGFUNC("em_config_mac_to_phy"); - - /* 82544 or newer MAC, Auto Speed Detection takes care of - * MAC speed/duplex configuration.*/ - if (hw->mac_type >= em_82544) - return E1000_SUCCESS; - - /* Read the Device Control Register and set the bits to Force Speed - * and Duplex. - */ - ctrl = E1000_READ_REG(hw, CTRL); - ctrl |= (E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX); - ctrl &= ~(E1000_CTRL_SPD_SEL | E1000_CTRL_ILOS); - - /* Set up duplex in the Device Control and Transmit Control - * registers depending on negotiated values. - */ - ret_val = em_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS, &phy_data); - if (ret_val) - return ret_val; - - if (phy_data & M88E1000_PSSR_DPLX) - ctrl |= E1000_CTRL_FD; - else - ctrl &= ~E1000_CTRL_FD; - - em_config_collision_dist(hw); - - /* Set up speed in the Device Control register depending on - * negotiated values. - */ - if ((phy_data & M88E1000_PSSR_SPEED) == M88E1000_PSSR_1000MBS) - ctrl |= E1000_CTRL_SPD_1000; - else if ((phy_data & M88E1000_PSSR_SPEED) == M88E1000_PSSR_100MBS) - ctrl |= E1000_CTRL_SPD_100; - - /* Write the configured values back to the Device Control Reg. */ - E1000_WRITE_REG(hw, CTRL, ctrl); - return E1000_SUCCESS; -} - -/****************************************************************************** - * Forces the MAC's flow control settings. - * - * hw - Struct containing variables accessed by shared code - * - * Sets the TFCE and RFCE bits in the device control register to reflect - * the adapter settings. TFCE and RFCE need to be explicitly set by - * software when a Copper PHY is used because autonegotiation is managed - * by the PHY rather than the MAC. Software must also configure these - * bits when link is forced on a fiber connection. - *****************************************************************************/ -int32_t -em_force_mac_fc(struct em_hw *hw) -{ - uint32_t ctrl; - - DEBUGFUNC("em_force_mac_fc"); - - /* Get the current configuration of the Device Control Register */ - ctrl = E1000_READ_REG(hw, CTRL); - - /* Because we didn't get link via the internal auto-negotiation - * mechanism (we either forced link or we got link via PHY - * auto-neg), we have to manually enable/disable transmit an - * receive flow control. - * - * The "Case" statement below enables/disable flow control - * according to the "hw->fc" parameter. - * - * The possible values of the "fc" parameter are: - * 0: Flow control is completely disabled - * 1: Rx flow control is enabled (we can receive pause - * frames but not send pause frames). - * 2: Tx flow control is enabled (we can send pause frames - * frames but we do not receive pause frames). - * 3: Both Rx and TX flow control (symmetric) is enabled. - * other: No other values should be possible at this point. - */ - - switch (hw->fc) { - case E1000_FC_NONE: - ctrl &= (~(E1000_CTRL_TFCE | E1000_CTRL_RFCE)); - break; - case E1000_FC_RX_PAUSE: - ctrl &= (~E1000_CTRL_TFCE); - ctrl |= E1000_CTRL_RFCE; - break; - case E1000_FC_TX_PAUSE: - ctrl &= (~E1000_CTRL_RFCE); - ctrl |= E1000_CTRL_TFCE; - break; - case E1000_FC_FULL: - ctrl |= (E1000_CTRL_TFCE | E1000_CTRL_RFCE); - break; - default: - DEBUGOUT("Flow control param set incorrectly\n"); - return -E1000_ERR_CONFIG; - } - - /* Disable TX Flow Control for 82542 (rev 2.0) */ - if (hw->mac_type == em_82542_rev2_0) - ctrl &= (~E1000_CTRL_TFCE); - - E1000_WRITE_REG(hw, CTRL, ctrl); - return E1000_SUCCESS; -} - -/****************************************************************************** - * Configures flow control settings after link is established - * - * hw - Struct containing variables accessed by shared code - * - * Should be called immediately after a valid link has been established. - * Forces MAC flow control settings if link was forced. When in MII/GMII mode - * and autonegotiation is enabled, the MAC flow control settings will be set - * based on the flow control negotiated by the PHY. In TBI mode, the TFCE - * and RFCE bits will be automaticaly set to the negotiated flow control mode. - *****************************************************************************/ -STATIC int32_t -em_config_fc_after_link_up(struct em_hw *hw) -{ - int32_t ret_val; - uint16_t mii_status_reg; - uint16_t mii_nway_adv_reg; - uint16_t mii_nway_lp_ability_reg; - uint16_t speed; - uint16_t duplex; - - DEBUGFUNC("em_config_fc_after_link_up"); - - /* Check for the case where we have fiber media and auto-neg failed - * so we had to force link. In this case, we need to force the - * configuration of the MAC to match the "fc" parameter. - */ - if (((hw->media_type == em_media_type_fiber) && (hw->autoneg_failed)) || - ((hw->media_type == em_media_type_internal_serdes) && - (hw->autoneg_failed)) || - ((hw->media_type == em_media_type_copper) && (!hw->autoneg))) { - ret_val = em_force_mac_fc(hw); - if (ret_val) { - DEBUGOUT("Error forcing flow control settings\n"); - return ret_val; - } - } - - /* Check for the case where we have copper media and auto-neg is - * enabled. In this case, we need to check and see if Auto-Neg - * has completed, and if so, how the PHY and link partner has - * flow control configured. - */ - if ((hw->media_type == em_media_type_copper) && hw->autoneg) { - /* Read the MII Status Register and check to see if AutoNeg - * has completed. We read this twice because this reg has - * some "sticky" (latched) bits. - */ - ret_val = em_read_phy_reg(hw, PHY_STATUS, &mii_status_reg); - if (ret_val) - return ret_val; - ret_val = em_read_phy_reg(hw, PHY_STATUS, &mii_status_reg); - if (ret_val) - return ret_val; - - if (mii_status_reg & MII_SR_AUTONEG_COMPLETE) { - /* The AutoNeg process has completed, so we now need to - * read both the Auto Negotiation Advertisement Register - * (Address 4) and the Auto_Negotiation Base Page Ability - * Register (Address 5) to determine how flow control was - * negotiated. - */ - ret_val = em_read_phy_reg(hw, PHY_AUTONEG_ADV, - &mii_nway_adv_reg); - if (ret_val) - return ret_val; - ret_val = em_read_phy_reg(hw, PHY_LP_ABILITY, - &mii_nway_lp_ability_reg); - if (ret_val) - return ret_val; - - /* Two bits in the Auto Negotiation Advertisement Register - * (Address 4) and two bits in the Auto Negotiation Base - * Page Ability Register (Address 5) determine flow control - * for both the PHY and the link partner. The following - * table, taken out of the IEEE 802.3ab/D6.0 dated March 25, - * 1999, describes these PAUSE resolution bits and how flow - * control is determined based upon these settings. - * NOTE: DC = Don't Care - * - * LOCAL DEVICE | LINK PARTNER - * PAUSE | ASM_DIR | PAUSE | ASM_DIR | NIC Resolution - *-------|---------|-------|---------|-------------------- - * 0 | 0 | DC | DC | em_fc_none - * 0 | 1 | 0 | DC | em_fc_none - * 0 | 1 | 1 | 0 | em_fc_none - * 0 | 1 | 1 | 1 | em_fc_tx_pause - * 1 | 0 | 0 | DC | em_fc_none - * 1 | DC | 1 | DC | em_fc_full - * 1 | 1 | 0 | 0 | em_fc_none - * 1 | 1 | 0 | 1 | em_fc_rx_pause - * - */ - /* Are both PAUSE bits set to 1? If so, this implies - * Symmetric Flow Control is enabled at both ends. The - * ASM_DIR bits are irrelevant per the spec. - * - * For Symmetric Flow Control: - * - * LOCAL DEVICE | LINK PARTNER - * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result - *-------|---------|-------|---------|-------------------- - * 1 | DC | 1 | DC | em_fc_full - * - */ - if ((mii_nway_adv_reg & NWAY_AR_PAUSE) && - (mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE)) { - /* Now we need to check if the user selected RX ONLY - * of pause frames. In this case, we had to advertise - * FULL flow control because we could not advertise RX - * ONLY. Hence, we must now check to see if we need to - * turn OFF the TRANSMISSION of PAUSE frames. - */ - if (hw->original_fc == E1000_FC_FULL) { - hw->fc = E1000_FC_FULL; - DEBUGOUT("Flow Control = FULL.\n"); - } else { - hw->fc = E1000_FC_RX_PAUSE; - DEBUGOUT("Flow Control = RX PAUSE frames only.\n"); - } - } - /* For receiving PAUSE frames ONLY. - * - * LOCAL DEVICE | LINK PARTNER - * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result - *-------|---------|-------|---------|-------------------- - * 0 | 1 | 1 | 1 | em_fc_tx_pause - * - */ - else if (!(mii_nway_adv_reg & NWAY_AR_PAUSE) && - (mii_nway_adv_reg & NWAY_AR_ASM_DIR) && - (mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) && - (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR)) { - hw->fc = E1000_FC_TX_PAUSE; - DEBUGOUT("Flow Control = TX PAUSE frames only.\n"); - } - /* For transmitting PAUSE frames ONLY. - * - * LOCAL DEVICE | LINK PARTNER - * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result - *-------|---------|-------|---------|-------------------- - * 1 | 1 | 0 | 1 | em_fc_rx_pause - * - */ - else if ((mii_nway_adv_reg & NWAY_AR_PAUSE) && - (mii_nway_adv_reg & NWAY_AR_ASM_DIR) && - !(mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) && - (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR)) { - hw->fc = E1000_FC_RX_PAUSE; - DEBUGOUT("Flow Control = RX PAUSE frames only.\n"); - } - /* Per the IEEE spec, at this point flow control should be - * disabled. However, we want to consider that we could - * be connected to a legacy switch that doesn't advertise - * desired flow control, but can be forced on the link - * partner. So if we advertised no flow control, that is - * what we will resolve to. If we advertised some kind of - * receive capability (Rx Pause Only or Full Flow Control) - * and the link partner advertised none, we will configure - * ourselves to enable Rx Flow Control only. We can do - * this safely for two reasons: If the link partner really - * didn't want flow control enabled, and we enable Rx, no - * harm done since we won't be receiving any PAUSE frames - * anyway. If the intent on the link partner was to have - * flow control enabled, then by us enabling RX only, we - * can at least receive pause frames and process them. - * This is a good idea because in most cases, since we are - * predominantly a server NIC, more times than not we will - * be asked to delay transmission of packets than asking - * our link partner to pause transmission of frames. - */ - else if ((hw->original_fc == E1000_FC_NONE|| - hw->original_fc == E1000_FC_TX_PAUSE) || - hw->fc_strict_ieee) { - hw->fc = E1000_FC_NONE; - DEBUGOUT("Flow Control = NONE.\n"); - } else { - hw->fc = E1000_FC_RX_PAUSE; - DEBUGOUT("Flow Control = RX PAUSE frames only.\n"); - } - - /* Now we need to do one last check... If we auto- - * negotiated to HALF DUPLEX, flow control should not be - * enabled per IEEE 802.3 spec. - */ - ret_val = em_get_speed_and_duplex(hw, &speed, &duplex); - if (ret_val) { - DEBUGOUT("Error getting link speed and duplex\n"); - return ret_val; - } - - if (duplex == HALF_DUPLEX) - hw->fc = E1000_FC_NONE; - - /* Now we call a subroutine to actually force the MAC - * controller to use the correct flow control settings. - */ - ret_val = em_force_mac_fc(hw); - if (ret_val) { - DEBUGOUT("Error forcing flow control settings\n"); - return ret_val; - } - } else { - DEBUGOUT("Copper PHY and Auto Neg has not completed.\n"); - } - } - return E1000_SUCCESS; -} - -/****************************************************************************** - * Checks to see if the link status of the hardware has changed. - * - * hw - Struct containing variables accessed by shared code - * - * Called by any function that needs to check the link status of the adapter. - *****************************************************************************/ -int32_t -em_check_for_link(struct em_hw *hw) -{ - uint32_t rxcw = 0; - uint32_t ctrl; - uint32_t status; - uint32_t rctl; - uint32_t icr; - uint32_t signal = 0; - int32_t ret_val; - uint16_t phy_data; - - DEBUGFUNC("em_check_for_link"); - - ctrl = E1000_READ_REG(hw, CTRL); - status = E1000_READ_REG(hw, STATUS); - - /* On adapters with a MAC newer than 82544, SW Defineable pin 1 will be - * set when the optics detect a signal. On older adapters, it will be - * cleared when there is a signal. This applies to fiber media only. - */ - if ((hw->media_type == em_media_type_fiber) || - (hw->media_type == em_media_type_internal_serdes)) { - rxcw = E1000_READ_REG(hw, RXCW); - - if (hw->media_type == em_media_type_fiber) { - signal = (hw->mac_type > em_82544) ? E1000_CTRL_SWDPIN1 : 0; - if (status & E1000_STATUS_LU) - hw->get_link_status = FALSE; - } - } - - /* If we have a copper PHY then we only want to go out to the PHY - * registers to see if Auto-Neg has completed and/or if our link - * status has changed. The get_link_status flag will be set if we - * receive a Link Status Change interrupt or we have Rx Sequence - * Errors. - */ - if ((hw->media_type == em_media_type_copper) && hw->get_link_status) { - /* First we want to see if the MII Status Register reports - * link. If so, then we want to get the current speed/duplex - * of the PHY. - * Read the register twice since the link bit is sticky. - */ - ret_val = em_read_phy_reg(hw, PHY_STATUS, &phy_data); - if (ret_val) - return ret_val; - ret_val = em_read_phy_reg(hw, PHY_STATUS, &phy_data); - if (ret_val) - return ret_val; - - if (phy_data & MII_SR_LINK_STATUS) { - hw->get_link_status = FALSE; - /* Check if there was DownShift, must be checked immediately after - * link-up */ - em_check_downshift(hw); - - /* If we are on 82544 or 82543 silicon and speed/duplex - * are forced to 10H or 10F, then we will implement the polarity - * reversal workaround. We disable interrupts first, and upon - * returning, place the devices interrupt state to its previous - * value except for the link status change interrupt which will - * happen due to the execution of this workaround. - */ - - if ((hw->mac_type == em_82544 || hw->mac_type == em_82543) && - (!hw->autoneg) && - (hw->forced_speed_duplex == em_10_full || - hw->forced_speed_duplex == em_10_half)) { - E1000_WRITE_REG(hw, IMC, 0xffffffff); - ret_val = em_polarity_reversal_workaround(hw); - icr = E1000_READ_REG(hw, ICR); - E1000_WRITE_REG(hw, ICS, (icr & ~E1000_ICS_LSC)); - E1000_WRITE_REG(hw, IMS, IMS_ENABLE_MASK); - } - - } else { - /* No link detected */ - em_config_dsp_after_link_change(hw, FALSE); - return 0; - } - - /* If we are forcing speed/duplex, then we simply return since - * we have already determined whether we have link or not. - */ - if (!hw->autoneg) return -E1000_ERR_CONFIG; - - /* optimize the dsp settings for the igp phy */ - em_config_dsp_after_link_change(hw, TRUE); - - /* We have a M88E1000 PHY and Auto-Neg is enabled. If we - * have Si on board that is 82544 or newer, Auto - * Speed Detection takes care of MAC speed/duplex - * configuration. So we only need to configure Collision - * Distance in the MAC. Otherwise, we need to force - * speed/duplex on the MAC to the current PHY speed/duplex - * settings. - */ - if (hw->mac_type >= em_82544) - em_config_collision_dist(hw); - else { - ret_val = em_config_mac_to_phy(hw); - if (ret_val) { - DEBUGOUT("Error configuring MAC to PHY settings\n"); - return ret_val; - } - } - - /* Configure Flow Control now that Auto-Neg has completed. First, we - * need to restore the desired flow control settings because we may - * have had to re-autoneg with a different link partner. - */ - ret_val = em_config_fc_after_link_up(hw); - if (ret_val) { - DEBUGOUT("Error configuring flow control\n"); - return ret_val; - } - - /* At this point we know that we are on copper and we have - * auto-negotiated link. These are conditions for checking the link - * partner capability register. We use the link speed to determine if - * TBI compatibility needs to be turned on or off. If the link is not - * at gigabit speed, then TBI compatibility is not needed. If we are - * at gigabit speed, we turn on TBI compatibility. - */ - if (hw->tbi_compatibility_en) { - uint16_t speed, duplex; - ret_val = em_get_speed_and_duplex(hw, &speed, &duplex); - if (ret_val) { - DEBUGOUT("Error getting link speed and duplex\n"); - return ret_val; - } - if (speed != SPEED_1000) { - /* If link speed is not set to gigabit speed, we do not need - * to enable TBI compatibility. - */ - if (hw->tbi_compatibility_on) { - /* If we previously were in the mode, turn it off. */ - rctl = E1000_READ_REG(hw, RCTL); - rctl &= ~E1000_RCTL_SBP; - E1000_WRITE_REG(hw, RCTL, rctl); - hw->tbi_compatibility_on = FALSE; - } - } else { - /* If TBI compatibility is was previously off, turn it on. For - * compatibility with a TBI link partner, we will store bad - * packets. Some frames have an additional byte on the end and - * will look like CRC errors to to the hardware. - */ - if (!hw->tbi_compatibility_on) { - hw->tbi_compatibility_on = TRUE; - rctl = E1000_READ_REG(hw, RCTL); - rctl |= E1000_RCTL_SBP; - E1000_WRITE_REG(hw, RCTL, rctl); - } - } - } - } - /* If we don't have link (auto-negotiation failed or link partner cannot - * auto-negotiate), the cable is plugged in (we have signal), and our - * link partner is not trying to auto-negotiate with us (we are receiving - * idles or data), we need to force link up. We also need to give - * auto-negotiation time to complete, in case the cable was just plugged - * in. The autoneg_failed flag does this. - */ - else if ((((hw->media_type == em_media_type_fiber) && - ((ctrl & E1000_CTRL_SWDPIN1) == signal)) || - (hw->media_type == em_media_type_internal_serdes)) && - (!(status & E1000_STATUS_LU)) && - (!(rxcw & E1000_RXCW_C))) { - if (hw->autoneg_failed == 0) { - hw->autoneg_failed = 1; - return 0; - } - DEBUGOUT("NOT RXing /C/, disable AutoNeg and force link.\n"); - - /* Disable auto-negotiation in the TXCW register */ - E1000_WRITE_REG(hw, TXCW, (hw->txcw & ~E1000_TXCW_ANE)); - - /* Force link-up and also force full-duplex. */ - ctrl = E1000_READ_REG(hw, CTRL); - ctrl |= (E1000_CTRL_SLU | E1000_CTRL_FD); - E1000_WRITE_REG(hw, CTRL, ctrl); - - /* Configure Flow Control after forcing link up. */ - ret_val = em_config_fc_after_link_up(hw); - if (ret_val) { - DEBUGOUT("Error configuring flow control\n"); - return ret_val; - } - } - /* If we are forcing link and we are receiving /C/ ordered sets, re-enable - * auto-negotiation in the TXCW register and disable forced link in the - * Device Control register in an attempt to auto-negotiate with our link - * partner. - */ - else if (((hw->media_type == em_media_type_fiber) || - (hw->media_type == em_media_type_internal_serdes)) && - (ctrl & E1000_CTRL_SLU) && (rxcw & E1000_RXCW_C)) { - DEBUGOUT("RXing /C/, enable AutoNeg and stop forcing link.\n"); - E1000_WRITE_REG(hw, TXCW, hw->txcw); - E1000_WRITE_REG(hw, CTRL, (ctrl & ~E1000_CTRL_SLU)); - - hw->serdes_link_down = FALSE; - } - /* If we force link for non-auto-negotiation switch, check link status - * based on MAC synchronization for internal serdes media type. - */ - else if ((hw->media_type == em_media_type_internal_serdes) && - !(E1000_TXCW_ANE & E1000_READ_REG(hw, TXCW))) { - /* SYNCH bit and IV bit are sticky. */ - usec_delay(10); - if (E1000_RXCW_SYNCH & E1000_READ_REG(hw, RXCW)) { - if (!(rxcw & E1000_RXCW_IV)) { - hw->serdes_link_down = FALSE; - DEBUGOUT("SERDES: Link is up.\n"); - } - } else { - hw->serdes_link_down = TRUE; - DEBUGOUT("SERDES: Link is down.\n"); - } - } - if ((hw->media_type == em_media_type_internal_serdes) && - (E1000_TXCW_ANE & E1000_READ_REG(hw, TXCW))) { - hw->serdes_link_down = !(E1000_STATUS_LU & E1000_READ_REG(hw, STATUS)); - } - return E1000_SUCCESS; -} - -/****************************************************************************** - * Detects the current speed and duplex settings of the hardware. - * - * hw - Struct containing variables accessed by shared code - * speed - Speed of the connection - * duplex - Duplex setting of the connection - *****************************************************************************/ -int32_t -em_get_speed_and_duplex(struct em_hw *hw, - uint16_t *speed, - uint16_t *duplex) -{ - uint32_t status; - int32_t ret_val; - uint16_t phy_data; - - DEBUGFUNC("em_get_speed_and_duplex"); - - if (hw->mac_type >= em_82543) { - status = E1000_READ_REG(hw, STATUS); - if (status & E1000_STATUS_SPEED_1000) { - *speed = SPEED_1000; - DEBUGOUT("1000 Mbs, "); - } else if (status & E1000_STATUS_SPEED_100) { - *speed = SPEED_100; - DEBUGOUT("100 Mbs, "); - } else { - *speed = SPEED_10; - DEBUGOUT("10 Mbs, "); - } - - if (status & E1000_STATUS_FD) { - *duplex = FULL_DUPLEX; - DEBUGOUT("Full Duplex\n"); - } else { - *duplex = HALF_DUPLEX; - DEBUGOUT(" Half Duplex\n"); - } - } else { - DEBUGOUT("1000 Mbs, Full Duplex\n"); - *speed = SPEED_1000; - *duplex = FULL_DUPLEX; - } - - /* IGP01 PHY may advertise full duplex operation after speed downgrade even - * if it is operating at half duplex. Here we set the duplex settings to - * match the duplex in the link partner's capabilities. - */ - if (hw->phy_type == em_phy_igp && hw->speed_downgraded) { - ret_val = em_read_phy_reg(hw, PHY_AUTONEG_EXP, &phy_data); - if (ret_val) - return ret_val; - - if (!(phy_data & NWAY_ER_LP_NWAY_CAPS)) - *duplex = HALF_DUPLEX; - else { - ret_val = em_read_phy_reg(hw, PHY_LP_ABILITY, &phy_data); - if (ret_val) - return ret_val; - if ((*speed == SPEED_100 && !(phy_data & NWAY_LPAR_100TX_FD_CAPS)) || - (*speed == SPEED_10 && !(phy_data & NWAY_LPAR_10T_FD_CAPS))) - *duplex = HALF_DUPLEX; - } - } - - if ((hw->mac_type == em_80003es2lan) && - (hw->media_type == em_media_type_copper)) { - if (*speed == SPEED_1000) - ret_val = em_configure_kmrn_for_1000(hw); - else - ret_val = em_configure_kmrn_for_10_100(hw, *duplex); - if (ret_val) - return ret_val; - } - - if ((hw->phy_type == em_phy_igp_3) && (*speed == SPEED_1000)) { - ret_val = em_kumeran_lock_loss_workaround(hw); - if (ret_val) - return ret_val; - } - - return E1000_SUCCESS; -} - -/****************************************************************************** -* Blocks until autoneg completes or times out (~4.5 seconds) -* -* hw - Struct containing variables accessed by shared code -******************************************************************************/ -STATIC int32_t -em_wait_autoneg(struct em_hw *hw) -{ - int32_t ret_val; - uint16_t i; - uint16_t phy_data; - - DEBUGFUNC("em_wait_autoneg"); - DEBUGOUT("Waiting for Auto-Neg to complete.\n"); - - /* We will wait for autoneg to complete or 4.5 seconds to expire. */ - for (i = PHY_AUTO_NEG_TIME; i > 0; i--) { - /* Read the MII Status Register and wait for Auto-Neg - * Complete bit to be set. - */ - ret_val = em_read_phy_reg(hw, PHY_STATUS, &phy_data); - if (ret_val) - return ret_val; - ret_val = em_read_phy_reg(hw, PHY_STATUS, &phy_data); - if (ret_val) - return ret_val; - if (phy_data & MII_SR_AUTONEG_COMPLETE) { - return E1000_SUCCESS; - } - msec_delay(100); - } - return E1000_SUCCESS; -} - -/****************************************************************************** -* Raises the Management Data Clock -* -* hw - Struct containing variables accessed by shared code -* ctrl - Device control register's current value -******************************************************************************/ -static void -em_raise_mdi_clk(struct em_hw *hw, - uint32_t *ctrl) -{ - /* Raise the clock input to the Management Data Clock (by setting the MDC - * bit), and then delay 10 microseconds. - */ - E1000_WRITE_REG(hw, CTRL, (*ctrl | E1000_CTRL_MDC)); - E1000_WRITE_FLUSH(hw); - usec_delay(10); -} - -/****************************************************************************** -* Lowers the Management Data Clock -* -* hw - Struct containing variables accessed by shared code -* ctrl - Device control register's current value -******************************************************************************/ -static void -em_lower_mdi_clk(struct em_hw *hw, - uint32_t *ctrl) -{ - /* Lower the clock input to the Management Data Clock (by clearing the MDC - * bit), and then delay 10 microseconds. - */ - E1000_WRITE_REG(hw, CTRL, (*ctrl & ~E1000_CTRL_MDC)); - E1000_WRITE_FLUSH(hw); - usec_delay(10); -} - -/****************************************************************************** -* Shifts data bits out to the PHY -* -* hw - Struct containing variables accessed by shared code -* data - Data to send out to the PHY -* count - Number of bits to shift out -* -* Bits are shifted out in MSB to LSB order. -******************************************************************************/ -static void -em_shift_out_mdi_bits(struct em_hw *hw, - uint32_t data, - uint16_t count) -{ - uint32_t ctrl; - uint32_t mask; - - /* We need to shift "count" number of bits out to the PHY. So, the value - * in the "data" parameter will be shifted out to the PHY one bit at a - * time. In order to do this, "data" must be broken down into bits. - */ - mask = 0x01; - mask <<= (count - 1); - - ctrl = E1000_READ_REG(hw, CTRL); - - /* Set MDIO_DIR and MDC_DIR direction bits to be used as output pins. */ - ctrl |= (E1000_CTRL_MDIO_DIR | E1000_CTRL_MDC_DIR); - - while (mask) { - /* A "1" is shifted out to the PHY by setting the MDIO bit to "1" and - * then raising and lowering the Management Data Clock. A "0" is - * shifted out to the PHY by setting the MDIO bit to "0" and then - * raising and lowering the clock. - */ - if (data & mask) - ctrl |= E1000_CTRL_MDIO; - else - ctrl &= ~E1000_CTRL_MDIO; - - E1000_WRITE_REG(hw, CTRL, ctrl); - E1000_WRITE_FLUSH(hw); - - usec_delay(10); - - em_raise_mdi_clk(hw, &ctrl); - em_lower_mdi_clk(hw, &ctrl); - - mask = mask >> 1; - } -} - -/****************************************************************************** -* Shifts data bits in from the PHY -* -* hw - Struct containing variables accessed by shared code -* -* Bits are shifted in in MSB to LSB order. -******************************************************************************/ -static uint16_t -em_shift_in_mdi_bits(struct em_hw *hw) -{ - uint32_t ctrl; - uint16_t data = 0; - uint8_t i; - - /* In order to read a register from the PHY, we need to shift in a total - * of 18 bits from the PHY. The first two bit (turnaround) times are used - * to avoid contention on the MDIO pin when a read operation is performed. - * These two bits are ignored by us and thrown away. Bits are "shifted in" - * by raising the input to the Management Data Clock (setting the MDC bit), - * and then reading the value of the MDIO bit. - */ - ctrl = E1000_READ_REG(hw, CTRL); - - /* Clear MDIO_DIR (SWDPIO1) to indicate this bit is to be used as input. */ - ctrl &= ~E1000_CTRL_MDIO_DIR; - ctrl &= ~E1000_CTRL_MDIO; - - E1000_WRITE_REG(hw, CTRL, ctrl); - E1000_WRITE_FLUSH(hw); - - /* Raise and Lower the clock before reading in the data. This accounts for - * the turnaround bits. The first clock occurred when we clocked out the - * last bit of the Register Address. - */ - em_raise_mdi_clk(hw, &ctrl); - em_lower_mdi_clk(hw, &ctrl); - - for (data = 0, i = 0; i < 16; i++) { - data = data << 1; - em_raise_mdi_clk(hw, &ctrl); - ctrl = E1000_READ_REG(hw, CTRL); - /* Check to see if we shifted in a "1". */ - if (ctrl & E1000_CTRL_MDIO) - data |= 1; - em_lower_mdi_clk(hw, &ctrl); - } - - em_raise_mdi_clk(hw, &ctrl); - em_lower_mdi_clk(hw, &ctrl); - - return data; -} - -STATIC int32_t -em_swfw_sync_acquire(struct em_hw *hw, uint16_t mask) -{ - uint32_t swfw_sync = 0; - uint32_t swmask = mask; - uint32_t fwmask = mask << 16; - int32_t timeout = 200; - - DEBUGFUNC("em_swfw_sync_acquire"); - - if (hw->swfwhw_semaphore_present) - return em_get_software_flag(hw); - - if (!hw->swfw_sync_present) - return em_get_hw_eeprom_semaphore(hw); - - while (timeout) { - if (em_get_hw_eeprom_semaphore(hw)) - return -E1000_ERR_SWFW_SYNC; - - swfw_sync = E1000_READ_REG(hw, SW_FW_SYNC); - if (!(swfw_sync & (fwmask | swmask))) { - break; - } - - /* firmware currently using resource (fwmask) */ - /* or other software thread currently using resource (swmask) */ - em_put_hw_eeprom_semaphore(hw); - msec_delay_irq(5); - timeout--; - } - - if (!timeout) { - DEBUGOUT("Driver can't access resource, SW_FW_SYNC timeout.\n"); - return -E1000_ERR_SWFW_SYNC; - } - - swfw_sync |= swmask; - E1000_WRITE_REG(hw, SW_FW_SYNC, swfw_sync); - - em_put_hw_eeprom_semaphore(hw); - return E1000_SUCCESS; -} - -STATIC void -em_swfw_sync_release(struct em_hw *hw, uint16_t mask) -{ - uint32_t swfw_sync; - uint32_t swmask = mask; - - DEBUGFUNC("em_swfw_sync_release"); - - if (hw->swfwhw_semaphore_present) { - em_release_software_flag(hw); - return; - } - - if (!hw->swfw_sync_present) { - em_put_hw_eeprom_semaphore(hw); - return; - } - - /* if (em_get_hw_eeprom_semaphore(hw)) - * return -E1000_ERR_SWFW_SYNC; */ - while (em_get_hw_eeprom_semaphore(hw) != E1000_SUCCESS); - /* empty */ - - swfw_sync = E1000_READ_REG(hw, SW_FW_SYNC); - swfw_sync &= ~swmask; - E1000_WRITE_REG(hw, SW_FW_SYNC, swfw_sync); - - em_put_hw_eeprom_semaphore(hw); -} - -/***************************************************************************** -* Reads the value from a PHY register, if the value is on a specific non zero -* page, sets the page first. -* hw - Struct containing variables accessed by shared code -* reg_addr - address of the PHY register to read -******************************************************************************/ -int32_t -em_read_phy_reg(struct em_hw *hw, - uint32_t reg_addr, - uint16_t *phy_data) -{ - uint32_t ret_val; - uint16_t swfw; - - DEBUGFUNC("em_read_phy_reg"); - - if ((hw->mac_type == em_80003es2lan) && - (E1000_READ_REG(hw, STATUS) & E1000_STATUS_FUNC_1)) { - swfw = E1000_SWFW_PHY1_SM; - } else { - swfw = E1000_SWFW_PHY0_SM; - } - if (em_swfw_sync_acquire(hw, swfw)) - return -E1000_ERR_SWFW_SYNC; - - if ((hw->phy_type == em_phy_igp || - hw->phy_type == em_phy_igp_3 || - hw->phy_type == em_phy_igp_2) && - (reg_addr > MAX_PHY_MULTI_PAGE_REG)) { - ret_val = em_write_phy_reg_ex(hw, IGP01E1000_PHY_PAGE_SELECT, - (uint16_t)reg_addr); - if (ret_val) { - em_swfw_sync_release(hw, swfw); - return ret_val; - } - } else if (hw->phy_type == em_phy_gg82563) { - if (((reg_addr & MAX_PHY_REG_ADDRESS) > MAX_PHY_MULTI_PAGE_REG) || - (hw->mac_type == em_80003es2lan)) { - /* Select Configuration Page */ - if ((reg_addr & MAX_PHY_REG_ADDRESS) < GG82563_MIN_ALT_REG) { - ret_val = em_write_phy_reg_ex(hw, GG82563_PHY_PAGE_SELECT, - (uint16_t)((uint16_t)reg_addr >> GG82563_PAGE_SHIFT)); - } else { - /* Use Alternative Page Select register to access - * registers 30 and 31 - */ - ret_val = em_write_phy_reg_ex(hw, - GG82563_PHY_PAGE_SELECT_ALT, - (uint16_t)((uint16_t)reg_addr >> GG82563_PAGE_SHIFT)); - } - - if (ret_val) { - em_swfw_sync_release(hw, swfw); - return ret_val; - } - } - } - - ret_val = em_read_phy_reg_ex(hw, MAX_PHY_REG_ADDRESS & reg_addr, - phy_data); - - em_swfw_sync_release(hw, swfw); - return ret_val; -} - -STATIC int32_t -em_read_phy_reg_ex(struct em_hw *hw, uint32_t reg_addr, - uint16_t *phy_data) -{ - uint32_t i; - uint32_t mdic = 0; - const uint32_t phy_addr = 1; - - DEBUGFUNC("em_read_phy_reg_ex"); - - if (reg_addr > MAX_PHY_REG_ADDRESS) { - DEBUGOUT1("PHY Address %d is out of range\n", reg_addr); - return -E1000_ERR_PARAM; - } - - if (hw->mac_type > em_82543) { - /* Set up Op-code, Phy Address, and register address in the MDI - * Control register. The MAC will take care of interfacing with the - * PHY to retrieve the desired data. - */ - mdic = ((reg_addr << E1000_MDIC_REG_SHIFT) | - (phy_addr << E1000_MDIC_PHY_SHIFT) | - (E1000_MDIC_OP_READ)); - - E1000_WRITE_REG(hw, MDIC, mdic); - - /* Poll the ready bit to see if the MDI read completed */ - for (i = 0; i < 64; i++) { - usec_delay(50); - mdic = E1000_READ_REG(hw, MDIC); - if (mdic & E1000_MDIC_READY) break; - } - if (!(mdic & E1000_MDIC_READY)) { - DEBUGOUT("MDI Read did not complete\n"); - return -E1000_ERR_PHY; - } - if (mdic & E1000_MDIC_ERROR) { - DEBUGOUT("MDI Error\n"); - return -E1000_ERR_PHY; - } - *phy_data = (uint16_t) mdic; - } else { - /* We must first send a preamble through the MDIO pin to signal the - * beginning of an MII instruction. This is done by sending 32 - * consecutive "1" bits. - */ - em_shift_out_mdi_bits(hw, PHY_PREAMBLE, PHY_PREAMBLE_SIZE); - - /* Now combine the next few fields that are required for a read - * operation. We use this method instead of calling the - * em_shift_out_mdi_bits routine five different times. The format of - * a MII read instruction consists of a shift out of 14 bits and is - * defined as follows: - * - * followed by a shift in of 18 bits. This first two bits shifted in - * are TurnAround bits used to avoid contention on the MDIO pin when a - * READ operation is performed. These two bits are thrown away - * followed by a shift in of 16 bits which contains the desired data. - */ - mdic = ((reg_addr) | (phy_addr << 5) | - (PHY_OP_READ << 10) | (PHY_SOF << 12)); - - em_shift_out_mdi_bits(hw, mdic, 14); - - /* Now that we've shifted out the read command to the MII, we need to - * "shift in" the 16-bit value (18 total bits) of the requested PHY - * register address. - */ - *phy_data = em_shift_in_mdi_bits(hw); - } - return E1000_SUCCESS; -} - -/****************************************************************************** -* Writes a value to a PHY register -* -* hw - Struct containing variables accessed by shared code -* reg_addr - address of the PHY register to write -* data - data to write to the PHY -******************************************************************************/ -int32_t -em_write_phy_reg(struct em_hw *hw, uint32_t reg_addr, - uint16_t phy_data) -{ - uint32_t ret_val; - uint16_t swfw; - - DEBUGFUNC("em_write_phy_reg"); - - if ((hw->mac_type == em_80003es2lan) && - (E1000_READ_REG(hw, STATUS) & E1000_STATUS_FUNC_1)) { - swfw = E1000_SWFW_PHY1_SM; - } else { - swfw = E1000_SWFW_PHY0_SM; - } - if (em_swfw_sync_acquire(hw, swfw)) - return -E1000_ERR_SWFW_SYNC; - - if ((hw->phy_type == em_phy_igp || - hw->phy_type == em_phy_igp_3 || - hw->phy_type == em_phy_igp_2) && - (reg_addr > MAX_PHY_MULTI_PAGE_REG)) { - ret_val = em_write_phy_reg_ex(hw, IGP01E1000_PHY_PAGE_SELECT, - (uint16_t)reg_addr); - if (ret_val) { - em_swfw_sync_release(hw, swfw); - return ret_val; - } - } else if (hw->phy_type == em_phy_gg82563) { - if (((reg_addr & MAX_PHY_REG_ADDRESS) > MAX_PHY_MULTI_PAGE_REG) || - (hw->mac_type == em_80003es2lan)) { - /* Select Configuration Page */ - if ((reg_addr & MAX_PHY_REG_ADDRESS) < GG82563_MIN_ALT_REG) { - ret_val = em_write_phy_reg_ex(hw, GG82563_PHY_PAGE_SELECT, - (uint16_t)((uint16_t)reg_addr >> GG82563_PAGE_SHIFT)); - } else { - /* Use Alternative Page Select register to access - * registers 30 and 31 - */ - ret_val = em_write_phy_reg_ex(hw, - GG82563_PHY_PAGE_SELECT_ALT, - (uint16_t)((uint16_t)reg_addr >> GG82563_PAGE_SHIFT)); - } - - if (ret_val) { - em_swfw_sync_release(hw, swfw); - return ret_val; - } - } - } - - ret_val = em_write_phy_reg_ex(hw, MAX_PHY_REG_ADDRESS & reg_addr, - phy_data); - - em_swfw_sync_release(hw, swfw); - return ret_val; -} - -STATIC int32_t -em_write_phy_reg_ex(struct em_hw *hw, uint32_t reg_addr, - uint16_t phy_data) -{ - uint32_t i; - uint32_t mdic = 0; - const uint32_t phy_addr = 1; - - DEBUGFUNC("em_write_phy_reg_ex"); - - if (reg_addr > MAX_PHY_REG_ADDRESS) { - DEBUGOUT1("PHY Address %d is out of range\n", reg_addr); - return -E1000_ERR_PARAM; - } - - if (hw->mac_type > em_82543) { - /* Set up Op-code, Phy Address, register address, and data intended - * for the PHY register in the MDI Control register. The MAC will take - * care of interfacing with the PHY to send the desired data. - */ - mdic = (((uint32_t) phy_data) | - (reg_addr << E1000_MDIC_REG_SHIFT) | - (phy_addr << E1000_MDIC_PHY_SHIFT) | - (E1000_MDIC_OP_WRITE)); - - E1000_WRITE_REG(hw, MDIC, mdic); - - /* Poll the ready bit to see if the MDI read completed */ - for (i = 0; i < 641; i++) { - usec_delay(5); - mdic = E1000_READ_REG(hw, MDIC); - if (mdic & E1000_MDIC_READY) break; - } - if (!(mdic & E1000_MDIC_READY)) { - DEBUGOUT("MDI Write did not complete\n"); - return -E1000_ERR_PHY; - } - } else { - /* We'll need to use the SW defined pins to shift the write command - * out to the PHY. We first send a preamble to the PHY to signal the - * beginning of the MII instruction. This is done by sending 32 - * consecutive "1" bits. - */ - em_shift_out_mdi_bits(hw, PHY_PREAMBLE, PHY_PREAMBLE_SIZE); - - /* Now combine the remaining required fields that will indicate a - * write operation. We use this method instead of calling the - * em_shift_out_mdi_bits routine for each field in the command. The - * format of a MII write instruction is as follows: - * . - */ - mdic = ((PHY_TURNAROUND) | (reg_addr << 2) | (phy_addr << 7) | - (PHY_OP_WRITE << 12) | (PHY_SOF << 14)); - mdic <<= 16; - mdic |= (uint32_t) phy_data; - - em_shift_out_mdi_bits(hw, mdic, 32); - } - - return E1000_SUCCESS; -} - -STATIC int32_t -em_read_kmrn_reg(struct em_hw *hw, - uint32_t reg_addr, - uint16_t *data) -{ - uint32_t reg_val; - uint16_t swfw; - DEBUGFUNC("em_read_kmrn_reg"); - - if ((hw->mac_type == em_80003es2lan) && - (E1000_READ_REG(hw, STATUS) & E1000_STATUS_FUNC_1)) { - swfw = E1000_SWFW_PHY1_SM; - } else { - swfw = E1000_SWFW_PHY0_SM; - } - if (em_swfw_sync_acquire(hw, swfw)) - return -E1000_ERR_SWFW_SYNC; - - /* Write register address */ - reg_val = ((reg_addr << E1000_KUMCTRLSTA_OFFSET_SHIFT) & - E1000_KUMCTRLSTA_OFFSET) | - E1000_KUMCTRLSTA_REN; - E1000_WRITE_REG(hw, KUMCTRLSTA, reg_val); - usec_delay(2); - - /* Read the data returned */ - reg_val = E1000_READ_REG(hw, KUMCTRLSTA); - *data = (uint16_t)reg_val; - - em_swfw_sync_release(hw, swfw); - return E1000_SUCCESS; -} - -STATIC int32_t -em_write_kmrn_reg(struct em_hw *hw, - uint32_t reg_addr, - uint16_t data) -{ - uint32_t reg_val; - uint16_t swfw; - DEBUGFUNC("em_write_kmrn_reg"); - - if ((hw->mac_type == em_80003es2lan) && - (E1000_READ_REG(hw, STATUS) & E1000_STATUS_FUNC_1)) { - swfw = E1000_SWFW_PHY1_SM; - } else { - swfw = E1000_SWFW_PHY0_SM; - } - if (em_swfw_sync_acquire(hw, swfw)) - return -E1000_ERR_SWFW_SYNC; - - reg_val = ((reg_addr << E1000_KUMCTRLSTA_OFFSET_SHIFT) & - E1000_KUMCTRLSTA_OFFSET) | data; - E1000_WRITE_REG(hw, KUMCTRLSTA, reg_val); - usec_delay(2); - - em_swfw_sync_release(hw, swfw); - return E1000_SUCCESS; -} - -/****************************************************************************** -* Returns the PHY to the power-on reset state -* -* hw - Struct containing variables accessed by shared code -******************************************************************************/ -int32_t -em_phy_hw_reset(struct em_hw *hw) -{ - uint32_t ctrl, ctrl_ext; - uint32_t led_ctrl; - int32_t ret_val; - uint16_t swfw; - - DEBUGFUNC("em_phy_hw_reset"); - - /* In the case of the phy reset being blocked, it's not an error, we - * simply return success without performing the reset. */ - ret_val = em_check_phy_reset_block(hw); - if (ret_val) - return E1000_SUCCESS; - - DEBUGOUT("Resetting Phy...\n"); - - if (hw->mac_type > em_82543) { - if ((hw->mac_type == em_80003es2lan) && - (E1000_READ_REG(hw, STATUS) & E1000_STATUS_FUNC_1)) { - swfw = E1000_SWFW_PHY1_SM; - } else { - swfw = E1000_SWFW_PHY0_SM; - } - if (em_swfw_sync_acquire(hw, swfw)) { - DEBUGOUT("Unable to acquire swfw sync\n"); - return -E1000_ERR_SWFW_SYNC; - } - /* Read the device control register and assert the E1000_CTRL_PHY_RST - * bit. Then, take it out of reset. - * For pre-em_82571 hardware, we delay for 10ms between the assert - * and deassert. For em_82571 hardware and later, we instead delay - * for 50us between and 10ms after the deassertion. - */ - ctrl = E1000_READ_REG(hw, CTRL); - E1000_WRITE_REG(hw, CTRL, ctrl | E1000_CTRL_PHY_RST); - E1000_WRITE_FLUSH(hw); - - if (hw->mac_type < em_82571) - msec_delay(10); - else - usec_delay(100); - - E1000_WRITE_REG(hw, CTRL, ctrl); - E1000_WRITE_FLUSH(hw); - - if (hw->mac_type >= em_82571) - msec_delay_irq(10); - - em_swfw_sync_release(hw, swfw); - } else { - /* Read the Extended Device Control Register, assert the PHY_RESET_DIR - * bit to put the PHY into reset. Then, take it out of reset. - */ - ctrl_ext = E1000_READ_REG(hw, CTRL_EXT); - ctrl_ext |= E1000_CTRL_EXT_SDP4_DIR; - ctrl_ext &= ~E1000_CTRL_EXT_SDP4_DATA; - E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext); - E1000_WRITE_FLUSH(hw); - msec_delay(10); - ctrl_ext |= E1000_CTRL_EXT_SDP4_DATA; - E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext); - E1000_WRITE_FLUSH(hw); - } - usec_delay(150); - - if ((hw->mac_type == em_82541) || (hw->mac_type == em_82547)) { - /* Configure activity LED after PHY reset */ - led_ctrl = E1000_READ_REG(hw, LEDCTL); - led_ctrl &= IGP_ACTIVITY_LED_MASK; - led_ctrl |= (IGP_ACTIVITY_LED_ENABLE | IGP_LED3_MODE); - E1000_WRITE_REG(hw, LEDCTL, led_ctrl); - } - - /* Wait for FW to finish PHY configuration. */ - ret_val = em_get_phy_cfg_done(hw); - if (ret_val != E1000_SUCCESS) - return ret_val; - em_release_software_semaphore(hw); - - if (((hw->mac_type == em_ich8lan) || (hw->mac_type == em_ich9lan)) - && (hw->phy_type == em_phy_igp_3)) - ret_val = em_init_lcd_from_nvm(hw); - - return ret_val; -} - -/****************************************************************************** -* Resets the PHY -* -* hw - Struct containing variables accessed by shared code -* -* Sets bit 15 of the MII Control regiser -******************************************************************************/ -int32_t -em_phy_reset(struct em_hw *hw) -{ - int32_t ret_val; - uint16_t phy_data; - - DEBUGFUNC("em_phy_reset"); - - /* In the case of the phy reset being blocked, it's not an error, we - * simply return success without performing the reset. */ - ret_val = em_check_phy_reset_block(hw); - if (ret_val) - return E1000_SUCCESS; - - switch (hw->phy_type) { - case em_phy_igp: - case em_phy_igp_2: - case em_phy_igp_3: - case em_phy_ife: - ret_val = em_phy_hw_reset(hw); - if (ret_val) - return ret_val; - break; - default: - ret_val = em_read_phy_reg(hw, PHY_CTRL, &phy_data); - if (ret_val) - return ret_val; - - phy_data |= MII_CR_RESET; - ret_val = em_write_phy_reg(hw, PHY_CTRL, phy_data); - if (ret_val) - return ret_val; - - usec_delay(1); - break; - } - - if (hw->phy_type == em_phy_igp || hw->phy_type == em_phy_igp_2) - em_phy_init_script(hw); - - return E1000_SUCCESS; -} - -/****************************************************************************** -* Work-around for 82566 power-down: on D3 entry- -* 1) disable gigabit link -* 2) write VR power-down enable -* 3) read it back -* if successful continue, else issue LCD reset and repeat -* -* hw - struct containing variables accessed by shared code -******************************************************************************/ -void -em_phy_powerdown_workaround(struct em_hw *hw) -{ - int32_t reg; - uint16_t phy_data; - int32_t retry = 0; - - DEBUGFUNC("em_phy_powerdown_workaround"); - - if (hw->phy_type != em_phy_igp_3) - return; - - do { - /* Disable link */ - reg = E1000_READ_REG(hw, PHY_CTRL); - E1000_WRITE_REG(hw, PHY_CTRL, reg | E1000_PHY_CTRL_GBE_DISABLE | - E1000_PHY_CTRL_NOND0A_GBE_DISABLE); - - /* Write VR power-down enable - bits 9:8 should be 10b */ - em_read_phy_reg(hw, IGP3_VR_CTRL, &phy_data); - phy_data |= (1 << 9); - phy_data &= ~(1 << 8); - em_write_phy_reg(hw, IGP3_VR_CTRL, phy_data); - - /* Read it back and test */ - em_read_phy_reg(hw, IGP3_VR_CTRL, &phy_data); - if (((phy_data & IGP3_VR_CTRL_MODE_MASK) == IGP3_VR_CTRL_MODE_SHUT) || retry) - break; - - /* Issue PHY reset and repeat at most one more time */ - reg = E1000_READ_REG(hw, CTRL); - E1000_WRITE_REG(hw, CTRL, reg | E1000_CTRL_PHY_RST); - retry++; - } while (retry); - - return; - -} - -/****************************************************************************** -* Work-around for 82566 Kumeran PCS lock loss: -* On link status change (i.e. PCI reset, speed change) and link is up and -* speed is gigabit- -* 0) if workaround is optionally disabled do nothing -* 1) wait 1ms for Kumeran link to come up -* 2) check Kumeran Diagnostic register PCS lock loss bit -* 3) if not set the link is locked (all is good), otherwise... -* 4) reset the PHY -* 5) repeat up to 10 times -* Note: this is only called for IGP3 copper when speed is 1gb. -* -* hw - struct containing variables accessed by shared code -******************************************************************************/ -STATIC int32_t -em_kumeran_lock_loss_workaround(struct em_hw *hw) -{ - int32_t ret_val; - int32_t reg; - int32_t cnt; - uint16_t phy_data; - - if (hw->kmrn_lock_loss_workaround_disabled) - return E1000_SUCCESS; - - /* Make sure link is up before proceeding. If not just return. - * Attempting this while link is negotiating fouled up link - * stability */ - ret_val = em_read_phy_reg(hw, PHY_STATUS, &phy_data); - ret_val = em_read_phy_reg(hw, PHY_STATUS, &phy_data); - - if (phy_data & MII_SR_LINK_STATUS) { - for (cnt = 0; cnt < 10; cnt++) { - /* read once to clear */ - ret_val = em_read_phy_reg(hw, IGP3_KMRN_DIAG, &phy_data); - if (ret_val) - return ret_val; - /* and again to get new status */ - ret_val = em_read_phy_reg(hw, IGP3_KMRN_DIAG, &phy_data); - if (ret_val) - return ret_val; - - /* check for PCS lock */ - if (!(phy_data & IGP3_KMRN_DIAG_PCS_LOCK_LOSS)) - return E1000_SUCCESS; - - /* Issue PHY reset */ - em_phy_hw_reset(hw); - msec_delay_irq(5); - } - /* Disable GigE link negotiation */ - reg = E1000_READ_REG(hw, PHY_CTRL); - E1000_WRITE_REG(hw, PHY_CTRL, reg | E1000_PHY_CTRL_GBE_DISABLE | - E1000_PHY_CTRL_NOND0A_GBE_DISABLE); - - /* unable to acquire PCS lock */ - return E1000_ERR_PHY; - } - - return E1000_SUCCESS; -} - -/****************************************************************************** -* Probes the expected PHY address for known PHY IDs -* -* hw - Struct containing variables accessed by shared code -******************************************************************************/ -STATIC int32_t -em_detect_gig_phy(struct em_hw *hw) -{ - int32_t phy_init_status, ret_val; - uint16_t phy_id_high, phy_id_low; - boolean_t match = FALSE; - - DEBUGFUNC("em_detect_gig_phy"); - - if (hw->phy_id != 0) - return E1000_SUCCESS; - - /* The 82571 firmware may still be configuring the PHY. In this - * case, we cannot access the PHY until the configuration is done. So - * we explicitly set the PHY values. */ - if (hw->mac_type == em_82571 || - hw->mac_type == em_82572) { - hw->phy_id = IGP01E1000_I_PHY_ID; - hw->phy_type = em_phy_igp_2; - return E1000_SUCCESS; - } - - /* ESB-2 PHY reads require em_phy_gg82563 to be set because of a work- - * around that forces PHY page 0 to be set or the reads fail. The rest of - * the code in this routine uses em_read_phy_reg to read the PHY ID. - * So for ESB-2 we need to have this set so our reads won't fail. If the - * attached PHY is not a em_phy_gg82563, the routines below will figure - * this out as well. */ - if (hw->mac_type == em_80003es2lan) - hw->phy_type = em_phy_gg82563; - - /* Read the PHY ID Registers to identify which PHY is onboard. */ - ret_val = em_read_phy_reg(hw, PHY_ID1, &phy_id_high); - if (ret_val) - return ret_val; - - hw->phy_id = (uint32_t) (phy_id_high << 16); - usec_delay(20); - ret_val = em_read_phy_reg(hw, PHY_ID2, &phy_id_low); - if (ret_val) - return ret_val; - - hw->phy_id |= (uint32_t) (phy_id_low & PHY_REVISION_MASK); - hw->phy_revision = (uint32_t) phy_id_low & ~PHY_REVISION_MASK; - - switch (hw->mac_type) { - case em_82543: - if (hw->phy_id == M88E1000_E_PHY_ID) match = TRUE; - break; - case em_82544: - if (hw->phy_id == M88E1000_I_PHY_ID) match = TRUE; - break; - case em_82540: - case em_82545: - case em_82545_rev_3: - case em_82546: - case em_82546_rev_3: - if (hw->phy_id == M88E1011_I_PHY_ID) match = TRUE; - break; - case em_82541: - case em_82541_rev_2: - case em_82547: - case em_82547_rev_2: - if (hw->phy_id == IGP01E1000_I_PHY_ID) match = TRUE; - break; - case em_82573: - if (hw->phy_id == M88E1111_I_PHY_ID) match = TRUE; - break; - case em_80003es2lan: - if (hw->phy_id == GG82563_E_PHY_ID) match = TRUE; - break; - case em_ich8lan: - case em_ich9lan: - if (hw->phy_id == IGP03E1000_E_PHY_ID) match = TRUE; - if (hw->phy_id == IFE_E_PHY_ID) match = TRUE; - if (hw->phy_id == IFE_PLUS_E_PHY_ID) match = TRUE; - if (hw->phy_id == IFE_C_E_PHY_ID) match = TRUE; - break; - default: - DEBUGOUT1("Invalid MAC type %d\n", hw->mac_type); - return -E1000_ERR_CONFIG; - } - phy_init_status = em_set_phy_type(hw); - - if ((match) && (phy_init_status == E1000_SUCCESS)) { - DEBUGOUT1("PHY ID 0x%X detected\n", hw->phy_id); - return E1000_SUCCESS; - } - DEBUGOUT1("Invalid PHY ID 0x%X\n", hw->phy_id); - return -E1000_ERR_PHY; -} - -/****************************************************************************** -* Resets the PHY's DSP -* -* hw - Struct containing variables accessed by shared code -******************************************************************************/ -static int32_t -em_phy_reset_dsp(struct em_hw *hw) -{ - int32_t ret_val; - DEBUGFUNC("em_phy_reset_dsp"); - - do { - if (hw->phy_type != em_phy_gg82563) { - ret_val = em_write_phy_reg(hw, 29, 0x001d); - if (ret_val) break; - } - ret_val = em_write_phy_reg(hw, 30, 0x00c1); - if (ret_val) break; - ret_val = em_write_phy_reg(hw, 30, 0x0000); - if (ret_val) break; - ret_val = E1000_SUCCESS; - } while (0); - - return ret_val; -} - -/****************************************************************************** -* Get PHY information from various PHY registers for igp PHY only. -* -* hw - Struct containing variables accessed by shared code -* phy_info - PHY information structure -******************************************************************************/ -STATIC int32_t -em_phy_igp_get_info(struct em_hw *hw, - struct em_phy_info *phy_info) -{ - int32_t ret_val; - uint16_t phy_data, min_length, max_length, average; - em_rev_polarity polarity; - - DEBUGFUNC("em_phy_igp_get_info"); - - /* The downshift status is checked only once, after link is established, - * and it stored in the hw->speed_downgraded parameter. */ - phy_info->downshift = (em_downshift)hw->speed_downgraded; - - /* IGP01E1000 does not need to support it. */ - phy_info->extended_10bt_distance = em_10bt_ext_dist_enable_normal; - - /* IGP01E1000 always correct polarity reversal */ - phy_info->polarity_correction = em_polarity_reversal_enabled; - - /* Check polarity status */ - ret_val = em_check_polarity(hw, &polarity); - if (ret_val) - return ret_val; - - phy_info->cable_polarity = polarity; - - ret_val = em_read_phy_reg(hw, IGP01E1000_PHY_PORT_STATUS, &phy_data); - if (ret_val) - return ret_val; - - phy_info->mdix_mode = (em_auto_x_mode)((phy_data & IGP01E1000_PSSR_MDIX) >> - IGP01E1000_PSSR_MDIX_SHIFT); - - if ((phy_data & IGP01E1000_PSSR_SPEED_MASK) == - IGP01E1000_PSSR_SPEED_1000MBPS) { - /* Local/Remote Receiver Information are only valid at 1000 Mbps */ - ret_val = em_read_phy_reg(hw, PHY_1000T_STATUS, &phy_data); - if (ret_val) - return ret_val; - - phy_info->local_rx = ((phy_data & SR_1000T_LOCAL_RX_STATUS) >> - SR_1000T_LOCAL_RX_STATUS_SHIFT) ? - em_1000t_rx_status_ok : em_1000t_rx_status_not_ok; - phy_info->remote_rx = ((phy_data & SR_1000T_REMOTE_RX_STATUS) >> - SR_1000T_REMOTE_RX_STATUS_SHIFT) ? - em_1000t_rx_status_ok : em_1000t_rx_status_not_ok; - - /* Get cable length */ - ret_val = em_get_cable_length(hw, &min_length, &max_length); - if (ret_val) - return ret_val; - - /* Translate to old method */ - average = (max_length + min_length) / 2; - - if (average <= em_igp_cable_length_50) - phy_info->cable_length = em_cable_length_50; - else if (average <= em_igp_cable_length_80) - phy_info->cable_length = em_cable_length_50_80; - else if (average <= em_igp_cable_length_110) - phy_info->cable_length = em_cable_length_80_110; - else if (average <= em_igp_cable_length_140) - phy_info->cable_length = em_cable_length_110_140; - else - phy_info->cable_length = em_cable_length_140; - } - - return E1000_SUCCESS; -} - -/****************************************************************************** -* Get PHY information from various PHY registers for ife PHY only. -* -* hw - Struct containing variables accessed by shared code -* phy_info - PHY information structure -******************************************************************************/ -STATIC int32_t -em_phy_ife_get_info(struct em_hw *hw, - struct em_phy_info *phy_info) -{ - int32_t ret_val; - uint16_t phy_data; - em_rev_polarity polarity; - - DEBUGFUNC("em_phy_ife_get_info"); - - phy_info->downshift = (em_downshift)hw->speed_downgraded; - phy_info->extended_10bt_distance = em_10bt_ext_dist_enable_normal; - - ret_val = em_read_phy_reg(hw, IFE_PHY_SPECIAL_CONTROL, &phy_data); - if (ret_val) - return ret_val; - phy_info->polarity_correction = - ((phy_data & IFE_PSC_AUTO_POLARITY_DISABLE) >> - IFE_PSC_AUTO_POLARITY_DISABLE_SHIFT) ? - em_polarity_reversal_disabled : em_polarity_reversal_enabled; - - if (phy_info->polarity_correction == em_polarity_reversal_enabled) { - ret_val = em_check_polarity(hw, &polarity); - if (ret_val) - return ret_val; - } else { - /* Polarity is forced. */ - polarity = ((phy_data & IFE_PSC_FORCE_POLARITY) >> - IFE_PSC_FORCE_POLARITY_SHIFT) ? - em_rev_polarity_reversed : em_rev_polarity_normal; - } - phy_info->cable_polarity = polarity; - - ret_val = em_read_phy_reg(hw, IFE_PHY_MDIX_CONTROL, &phy_data); - if (ret_val) - return ret_val; - - phy_info->mdix_mode = (em_auto_x_mode) - ((phy_data & (IFE_PMC_AUTO_MDIX | IFE_PMC_FORCE_MDIX)) >> - IFE_PMC_MDIX_MODE_SHIFT); - - return E1000_SUCCESS; -} - -/****************************************************************************** -* Get PHY information from various PHY registers fot m88 PHY only. -* -* hw - Struct containing variables accessed by shared code -* phy_info - PHY information structure -******************************************************************************/ -STATIC int32_t -em_phy_m88_get_info(struct em_hw *hw, - struct em_phy_info *phy_info) -{ - int32_t ret_val; - uint16_t phy_data; - em_rev_polarity polarity; - - DEBUGFUNC("em_phy_m88_get_info"); - - /* The downshift status is checked only once, after link is established, - * and it stored in the hw->speed_downgraded parameter. */ - phy_info->downshift = (em_downshift)hw->speed_downgraded; - - ret_val = em_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data); - if (ret_val) - return ret_val; - - phy_info->extended_10bt_distance = - ((phy_data & M88E1000_PSCR_10BT_EXT_DIST_ENABLE) >> - M88E1000_PSCR_10BT_EXT_DIST_ENABLE_SHIFT) ? - em_10bt_ext_dist_enable_lower : em_10bt_ext_dist_enable_normal; - - phy_info->polarity_correction = - ((phy_data & M88E1000_PSCR_POLARITY_REVERSAL) >> - M88E1000_PSCR_POLARITY_REVERSAL_SHIFT) ? - em_polarity_reversal_disabled : em_polarity_reversal_enabled; - - /* Check polarity status */ - ret_val = em_check_polarity(hw, &polarity); - if (ret_val) - return ret_val; - phy_info->cable_polarity = polarity; - - ret_val = em_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS, &phy_data); - if (ret_val) - return ret_val; - - phy_info->mdix_mode = (em_auto_x_mode)((phy_data & M88E1000_PSSR_MDIX) >> - M88E1000_PSSR_MDIX_SHIFT); - - if ((phy_data & M88E1000_PSSR_SPEED) == M88E1000_PSSR_1000MBS) { - /* Cable Length Estimation and Local/Remote Receiver Information - * are only valid at 1000 Mbps. - */ - if (hw->phy_type != em_phy_gg82563) { - phy_info->cable_length = (em_cable_length)((phy_data & M88E1000_PSSR_CABLE_LENGTH) >> - M88E1000_PSSR_CABLE_LENGTH_SHIFT); - } else { - ret_val = em_read_phy_reg(hw, GG82563_PHY_DSP_DISTANCE, - &phy_data); - if (ret_val) - return ret_val; - - phy_info->cable_length = (em_cable_length)(phy_data & GG82563_DSPD_CABLE_LENGTH); - } - - ret_val = em_read_phy_reg(hw, PHY_1000T_STATUS, &phy_data); - if (ret_val) - return ret_val; - - phy_info->local_rx = ((phy_data & SR_1000T_LOCAL_RX_STATUS) >> - SR_1000T_LOCAL_RX_STATUS_SHIFT) ? - em_1000t_rx_status_ok : em_1000t_rx_status_not_ok; - phy_info->remote_rx = ((phy_data & SR_1000T_REMOTE_RX_STATUS) >> - SR_1000T_REMOTE_RX_STATUS_SHIFT) ? - em_1000t_rx_status_ok : em_1000t_rx_status_not_ok; - - } - - return E1000_SUCCESS; -} - -/****************************************************************************** -* Get PHY information from various PHY registers -* -* hw - Struct containing variables accessed by shared code -* phy_info - PHY information structure -******************************************************************************/ -int32_t -em_phy_get_info(struct em_hw *hw, - struct em_phy_info *phy_info) -{ - int32_t ret_val; - uint16_t phy_data; - - DEBUGFUNC("em_phy_get_info"); - - phy_info->cable_length = em_cable_length_undefined; - phy_info->extended_10bt_distance = em_10bt_ext_dist_enable_undefined; - phy_info->cable_polarity = em_rev_polarity_undefined; - phy_info->downshift = em_downshift_undefined; - phy_info->polarity_correction = em_polarity_reversal_undefined; - phy_info->mdix_mode = em_auto_x_mode_undefined; - phy_info->local_rx = em_1000t_rx_status_undefined; - phy_info->remote_rx = em_1000t_rx_status_undefined; - - if (hw->media_type != em_media_type_copper) { - DEBUGOUT("PHY info is only valid for copper media\n"); - return -E1000_ERR_CONFIG; - } - - ret_val = em_read_phy_reg(hw, PHY_STATUS, &phy_data); - if (ret_val) - return ret_val; - - ret_val = em_read_phy_reg(hw, PHY_STATUS, &phy_data); - if (ret_val) - return ret_val; - - if ((phy_data & MII_SR_LINK_STATUS) != MII_SR_LINK_STATUS) { - DEBUGOUT("PHY info is only valid if link is up\n"); - return -E1000_ERR_CONFIG; - } - - if (hw->phy_type == em_phy_igp || - hw->phy_type == em_phy_igp_3 || - hw->phy_type == em_phy_igp_2) - return em_phy_igp_get_info(hw, phy_info); - else if (hw->phy_type == em_phy_ife) - return em_phy_ife_get_info(hw, phy_info); - else - return em_phy_m88_get_info(hw, phy_info); -} - -int32_t -em_validate_mdi_setting(struct em_hw *hw) -{ - DEBUGFUNC("em_validate_mdi_settings"); - - if (!hw->autoneg && (hw->mdix == 0 || hw->mdix == 3)) { - DEBUGOUT("Invalid MDI setting detected\n"); - hw->mdix = 1; - return -E1000_ERR_CONFIG; - } - return E1000_SUCCESS; -} - - -/****************************************************************************** - * Sets up eeprom variables in the hw struct. Must be called after mac_type - * is configured. Additionally, if this is ICH8, the flash controller GbE - * registers must be mapped, or this will crash. - * - * hw - Struct containing variables accessed by shared code - *****************************************************************************/ -int32_t -em_init_eeprom_params(struct em_hw *hw) -{ - struct em_eeprom_info *eeprom = &hw->eeprom; - uint32_t eecd = E1000_READ_REG(hw, EECD); - int32_t ret_val = E1000_SUCCESS; - uint16_t eeprom_size; - - DEBUGFUNC("em_init_eeprom_params"); - - switch (hw->mac_type) { - case em_82542_rev2_0: - case em_82542_rev2_1: - case em_82543: - case em_82544: - eeprom->type = em_eeprom_microwire; - eeprom->word_size = 64; - eeprom->opcode_bits = 3; - eeprom->address_bits = 6; - eeprom->delay_usec = 50; - eeprom->use_eerd = FALSE; - eeprom->use_eewr = FALSE; - break; - case em_82540: - case em_82545: - case em_82545_rev_3: - case em_82546: - case em_82546_rev_3: - eeprom->type = em_eeprom_microwire; - eeprom->opcode_bits = 3; - eeprom->delay_usec = 50; - if (eecd & E1000_EECD_SIZE) { - eeprom->word_size = 256; - eeprom->address_bits = 8; - } else { - eeprom->word_size = 64; - eeprom->address_bits = 6; - } - eeprom->use_eerd = FALSE; - eeprom->use_eewr = FALSE; - break; - case em_82541: - case em_82541_rev_2: - case em_82547: - case em_82547_rev_2: - if (eecd & E1000_EECD_TYPE) { - eeprom->type = em_eeprom_spi; - eeprom->opcode_bits = 8; - eeprom->delay_usec = 1; - if (eecd & E1000_EECD_ADDR_BITS) { - eeprom->page_size = 32; - eeprom->address_bits = 16; - } else { - eeprom->page_size = 8; - eeprom->address_bits = 8; - } - } else { - eeprom->type = em_eeprom_microwire; - eeprom->opcode_bits = 3; - eeprom->delay_usec = 50; - if (eecd & E1000_EECD_ADDR_BITS) { - eeprom->word_size = 256; - eeprom->address_bits = 8; - } else { - eeprom->word_size = 64; - eeprom->address_bits = 6; - } - } - eeprom->use_eerd = FALSE; - eeprom->use_eewr = FALSE; - break; - case em_82571: - case em_82572: - eeprom->type = em_eeprom_spi; - eeprom->opcode_bits = 8; - eeprom->delay_usec = 1; - if (eecd & E1000_EECD_ADDR_BITS) { - eeprom->page_size = 32; - eeprom->address_bits = 16; - } else { - eeprom->page_size = 8; - eeprom->address_bits = 8; - } - eeprom->use_eerd = FALSE; - eeprom->use_eewr = FALSE; - break; - case em_82573: - eeprom->type = em_eeprom_spi; - eeprom->opcode_bits = 8; - eeprom->delay_usec = 1; - if (eecd & E1000_EECD_ADDR_BITS) { - eeprom->page_size = 32; - eeprom->address_bits = 16; - } else { - eeprom->page_size = 8; - eeprom->address_bits = 8; - } - eeprom->use_eerd = TRUE; - eeprom->use_eewr = TRUE; - if (em_is_onboard_nvm_eeprom(hw) == FALSE) { - eeprom->type = em_eeprom_flash; - eeprom->word_size = 2048; - - /* Ensure that the Autonomous FLASH update bit is cleared due to - * Flash update issue on parts which use a FLASH for NVM. */ - eecd &= ~E1000_EECD_AUPDEN; - E1000_WRITE_REG(hw, EECD, eecd); - } - break; - case em_80003es2lan: - eeprom->type = em_eeprom_spi; - eeprom->opcode_bits = 8; - eeprom->delay_usec = 1; - if (eecd & E1000_EECD_ADDR_BITS) { - eeprom->page_size = 32; - eeprom->address_bits = 16; - } else { - eeprom->page_size = 8; - eeprom->address_bits = 8; - } - eeprom->use_eerd = TRUE; - eeprom->use_eewr = FALSE; - break; - case em_ich8lan: - case em_ich9lan: - { - int32_t i = 0; - uint32_t flash_size = E1000_READ_ICH_FLASH_REG(hw, ICH_FLASH_GFPREG); - - eeprom->type = em_eeprom_ich8; - eeprom->use_eerd = FALSE; - eeprom->use_eewr = FALSE; - eeprom->word_size = E1000_SHADOW_RAM_WORDS; - - /* Zero the shadow RAM structure. But don't load it from NVM - * so as to save time for driver init */ - if (hw->eeprom_shadow_ram != NULL) { - for (i = 0; i < E1000_SHADOW_RAM_WORDS; i++) { - hw->eeprom_shadow_ram[i].modified = FALSE; - hw->eeprom_shadow_ram[i].eeprom_word = 0xFFFF; - } - } - - hw->flash_base_addr = (flash_size & ICH_GFPREG_BASE_MASK) * - ICH_FLASH_SECTOR_SIZE; - - hw->flash_bank_size = ((flash_size >> 16) & ICH_GFPREG_BASE_MASK) + 1; - hw->flash_bank_size -= (flash_size & ICH_GFPREG_BASE_MASK); - - hw->flash_bank_size *= ICH_FLASH_SECTOR_SIZE; - - hw->flash_bank_size /= 2 * sizeof(uint16_t); - - break; - } - default: - break; - } - - if (eeprom->type == em_eeprom_spi) { - /* eeprom_size will be an enum [0..8] that maps to eeprom sizes 128B to - * 32KB (incremented by powers of 2). - */ - if (hw->mac_type <= em_82547_rev_2) { - /* Set to default value for initial eeprom read. */ - eeprom->word_size = 64; - ret_val = em_read_eeprom(hw, EEPROM_CFG, 1, &eeprom_size); - if (ret_val) - return ret_val; - eeprom_size = (eeprom_size & EEPROM_SIZE_MASK) >> EEPROM_SIZE_SHIFT; - /* 256B eeprom size was not supported in earlier hardware, so we - * bump eeprom_size up one to ensure that "1" (which maps to 256B) - * is never the result used in the shifting logic below. */ - if (eeprom_size) - eeprom_size++; - } else { - eeprom_size = (uint16_t)((eecd & E1000_EECD_SIZE_EX_MASK) >> - E1000_EECD_SIZE_EX_SHIFT); - } - - eeprom->word_size = 1 << (eeprom_size + EEPROM_WORD_SIZE_SHIFT); - } - return ret_val; -} - -/****************************************************************************** - * Raises the EEPROM's clock input. - * - * hw - Struct containing variables accessed by shared code - * eecd - EECD's current value - *****************************************************************************/ -static void -em_raise_ee_clk(struct em_hw *hw, - uint32_t *eecd) -{ - /* Raise the clock input to the EEPROM (by setting the SK bit), and then - * wait microseconds. - */ - *eecd = *eecd | E1000_EECD_SK; - E1000_WRITE_REG(hw, EECD, *eecd); - E1000_WRITE_FLUSH(hw); - usec_delay(hw->eeprom.delay_usec); -} - -/****************************************************************************** - * Lowers the EEPROM's clock input. - * - * hw - Struct containing variables accessed by shared code - * eecd - EECD's current value - *****************************************************************************/ -static void -em_lower_ee_clk(struct em_hw *hw, - uint32_t *eecd) -{ - /* Lower the clock input to the EEPROM (by clearing the SK bit), and then - * wait 50 microseconds. - */ - *eecd = *eecd & ~E1000_EECD_SK; - E1000_WRITE_REG(hw, EECD, *eecd); - E1000_WRITE_FLUSH(hw); - usec_delay(hw->eeprom.delay_usec); -} - -/****************************************************************************** - * Shift data bits out to the EEPROM. - * - * hw - Struct containing variables accessed by shared code - * data - data to send to the EEPROM - * count - number of bits to shift out - *****************************************************************************/ -static void -em_shift_out_ee_bits(struct em_hw *hw, - uint16_t data, - uint16_t count) -{ - struct em_eeprom_info *eeprom = &hw->eeprom; - uint32_t eecd; - uint32_t mask; - - /* We need to shift "count" bits out to the EEPROM. So, value in the - * "data" parameter will be shifted out to the EEPROM one bit at a time. - * In order to do this, "data" must be broken down into bits. - */ - mask = 0x01 << (count - 1); - eecd = E1000_READ_REG(hw, EECD); - if (eeprom->type == em_eeprom_microwire) { - eecd &= ~E1000_EECD_DO; - } else if (eeprom->type == em_eeprom_spi) { - eecd |= E1000_EECD_DO; - } - do { - /* A "1" is shifted out to the EEPROM by setting bit "DI" to a "1", - * and then raising and then lowering the clock (the SK bit controls - * the clock input to the EEPROM). A "0" is shifted out to the EEPROM - * by setting "DI" to "0" and then raising and then lowering the clock. - */ - eecd &= ~E1000_EECD_DI; - - if (data & mask) - eecd |= E1000_EECD_DI; - - E1000_WRITE_REG(hw, EECD, eecd); - E1000_WRITE_FLUSH(hw); - - usec_delay(eeprom->delay_usec); - - em_raise_ee_clk(hw, &eecd); - em_lower_ee_clk(hw, &eecd); - - mask = mask >> 1; - - } while (mask); - - /* We leave the "DI" bit set to "0" when we leave this routine. */ - eecd &= ~E1000_EECD_DI; - E1000_WRITE_REG(hw, EECD, eecd); -} - -/****************************************************************************** - * Shift data bits in from the EEPROM - * - * hw - Struct containing variables accessed by shared code - *****************************************************************************/ -static uint16_t -em_shift_in_ee_bits(struct em_hw *hw, - uint16_t count) -{ - uint32_t eecd; - uint32_t i; - uint16_t data; - - /* In order to read a register from the EEPROM, we need to shift 'count' - * bits in from the EEPROM. Bits are "shifted in" by raising the clock - * input to the EEPROM (setting the SK bit), and then reading the value of - * the "DO" bit. During this "shifting in" process the "DI" bit should - * always be clear. - */ - - eecd = E1000_READ_REG(hw, EECD); - - eecd &= ~(E1000_EECD_DO | E1000_EECD_DI); - data = 0; - - for (i = 0; i < count; i++) { - data = data << 1; - em_raise_ee_clk(hw, &eecd); - - eecd = E1000_READ_REG(hw, EECD); - - eecd &= ~(E1000_EECD_DI); - if (eecd & E1000_EECD_DO) - data |= 1; - - em_lower_ee_clk(hw, &eecd); - } - - return data; -} - -/****************************************************************************** - * Prepares EEPROM for access - * - * hw - Struct containing variables accessed by shared code - * - * Lowers EEPROM clock. Clears input pin. Sets the chip select pin. This - * function should be called before issuing a command to the EEPROM. - *****************************************************************************/ -static int32_t -em_acquire_eeprom(struct em_hw *hw) -{ - struct em_eeprom_info *eeprom = &hw->eeprom; - uint32_t eecd, i=0; - - DEBUGFUNC("em_acquire_eeprom"); - - if (em_swfw_sync_acquire(hw, E1000_SWFW_EEP_SM)) - return -E1000_ERR_SWFW_SYNC; - eecd = E1000_READ_REG(hw, EECD); - - if (hw->mac_type != em_82573) { - /* Request EEPROM Access */ - if (hw->mac_type > em_82544) { - eecd |= E1000_EECD_REQ; - E1000_WRITE_REG(hw, EECD, eecd); - eecd = E1000_READ_REG(hw, EECD); - while ((!(eecd & E1000_EECD_GNT)) && - (i < E1000_EEPROM_GRANT_ATTEMPTS)) { - i++; - usec_delay(5); - eecd = E1000_READ_REG(hw, EECD); - } - if (!(eecd & E1000_EECD_GNT)) { - eecd &= ~E1000_EECD_REQ; - E1000_WRITE_REG(hw, EECD, eecd); - DEBUGOUT("Could not acquire EEPROM grant\n"); - em_swfw_sync_release(hw, E1000_SWFW_EEP_SM); - return -E1000_ERR_EEPROM; - } - } - } - - /* Setup EEPROM for Read/Write */ - - if (eeprom->type == em_eeprom_microwire) { - /* Clear SK and DI */ - eecd &= ~(E1000_EECD_DI | E1000_EECD_SK); - E1000_WRITE_REG(hw, EECD, eecd); - - /* Set CS */ - eecd |= E1000_EECD_CS; - E1000_WRITE_REG(hw, EECD, eecd); - } else if (eeprom->type == em_eeprom_spi) { - /* Clear SK and CS */ - eecd &= ~(E1000_EECD_CS | E1000_EECD_SK); - E1000_WRITE_REG(hw, EECD, eecd); - usec_delay(1); - } - - return E1000_SUCCESS; -} - -/****************************************************************************** - * Returns EEPROM to a "standby" state - * - * hw - Struct containing variables accessed by shared code - *****************************************************************************/ -static void -em_standby_eeprom(struct em_hw *hw) -{ - struct em_eeprom_info *eeprom = &hw->eeprom; - uint32_t eecd; - - eecd = E1000_READ_REG(hw, EECD); - - if (eeprom->type == em_eeprom_microwire) { - eecd &= ~(E1000_EECD_CS | E1000_EECD_SK); - E1000_WRITE_REG(hw, EECD, eecd); - E1000_WRITE_FLUSH(hw); - usec_delay(eeprom->delay_usec); - - /* Clock high */ - eecd |= E1000_EECD_SK; - E1000_WRITE_REG(hw, EECD, eecd); - E1000_WRITE_FLUSH(hw); - usec_delay(eeprom->delay_usec); - - /* Select EEPROM */ - eecd |= E1000_EECD_CS; - E1000_WRITE_REG(hw, EECD, eecd); - E1000_WRITE_FLUSH(hw); - usec_delay(eeprom->delay_usec); - - /* Clock low */ - eecd &= ~E1000_EECD_SK; - E1000_WRITE_REG(hw, EECD, eecd); - E1000_WRITE_FLUSH(hw); - usec_delay(eeprom->delay_usec); - } else if (eeprom->type == em_eeprom_spi) { - /* Toggle CS to flush commands */ - eecd |= E1000_EECD_CS; - E1000_WRITE_REG(hw, EECD, eecd); - E1000_WRITE_FLUSH(hw); - usec_delay(eeprom->delay_usec); - eecd &= ~E1000_EECD_CS; - E1000_WRITE_REG(hw, EECD, eecd); - E1000_WRITE_FLUSH(hw); - usec_delay(eeprom->delay_usec); - } -} - -/****************************************************************************** - * Terminates a command by inverting the EEPROM's chip select pin - * - * hw - Struct containing variables accessed by shared code - *****************************************************************************/ -static void -em_release_eeprom(struct em_hw *hw) -{ - uint32_t eecd; - - DEBUGFUNC("em_release_eeprom"); - - eecd = E1000_READ_REG(hw, EECD); - - if (hw->eeprom.type == em_eeprom_spi) { - eecd |= E1000_EECD_CS; /* Pull CS high */ - eecd &= ~E1000_EECD_SK; /* Lower SCK */ - - E1000_WRITE_REG(hw, EECD, eecd); - - usec_delay(hw->eeprom.delay_usec); - } else if (hw->eeprom.type == em_eeprom_microwire) { - /* cleanup eeprom */ - - /* CS on Microwire is active-high */ - eecd &= ~(E1000_EECD_CS | E1000_EECD_DI); - - E1000_WRITE_REG(hw, EECD, eecd); - - /* Rising edge of clock */ - eecd |= E1000_EECD_SK; - E1000_WRITE_REG(hw, EECD, eecd); - E1000_WRITE_FLUSH(hw); - usec_delay(hw->eeprom.delay_usec); - - /* Falling edge of clock */ - eecd &= ~E1000_EECD_SK; - E1000_WRITE_REG(hw, EECD, eecd); - E1000_WRITE_FLUSH(hw); - usec_delay(hw->eeprom.delay_usec); - } - - /* Stop requesting EEPROM access */ - if (hw->mac_type > em_82544) { - eecd &= ~E1000_EECD_REQ; - E1000_WRITE_REG(hw, EECD, eecd); - } - - em_swfw_sync_release(hw, E1000_SWFW_EEP_SM); -} - -/****************************************************************************** - * Reads a 16 bit word from the EEPROM. - * - * hw - Struct containing variables accessed by shared code - *****************************************************************************/ -STATIC int32_t -em_spi_eeprom_ready(struct em_hw *hw) -{ - uint16_t retry_count = 0; - uint8_t spi_stat_reg; - - DEBUGFUNC("em_spi_eeprom_ready"); - - /* Read "Status Register" repeatedly until the LSB is cleared. The - * EEPROM will signal that the command has been completed by clearing - * bit 0 of the internal status register. If it's not cleared within - * 5 milliseconds, then error out. - */ - retry_count = 0; - do { - em_shift_out_ee_bits(hw, EEPROM_RDSR_OPCODE_SPI, - hw->eeprom.opcode_bits); - spi_stat_reg = (uint8_t)em_shift_in_ee_bits(hw, 8); - if (!(spi_stat_reg & EEPROM_STATUS_RDY_SPI)) - break; - - usec_delay(5); - retry_count += 5; - - em_standby_eeprom(hw); - } while (retry_count < EEPROM_MAX_RETRY_SPI); - - /* ATMEL SPI write time could vary from 0-20mSec on 3.3V devices (and - * only 0-5mSec on 5V devices) - */ - if (retry_count >= EEPROM_MAX_RETRY_SPI) { - DEBUGOUT("SPI EEPROM Status error\n"); - return -E1000_ERR_EEPROM; - } - - return E1000_SUCCESS; -} - -/****************************************************************************** - * Reads a 16 bit word from the EEPROM. - * - * hw - Struct containing variables accessed by shared code - * offset - offset of word in the EEPROM to read - * data - word read from the EEPROM - * words - number of words to read - *****************************************************************************/ -int32_t -em_read_eeprom(struct em_hw *hw, - uint16_t offset, - uint16_t words, - uint16_t *data) -{ - struct em_eeprom_info *eeprom = &hw->eeprom; - uint32_t i = 0; - - DEBUGFUNC("em_read_eeprom"); - - /* If eeprom is not yet detected, do so now */ - if (eeprom->word_size == 0) - em_init_eeprom_params(hw); - - /* A check for invalid values: offset too large, too many words, and not - * enough words. - */ - if ((offset >= eeprom->word_size) || (words > eeprom->word_size - offset) || - (words == 0)) { - DEBUGOUT2("\"words\" parameter out of bounds. Words = %d, size = %d\n", offset, eeprom->word_size); - return -E1000_ERR_EEPROM; - } - - /* EEPROM's that don't use EERD to read require us to bit-bang the SPI - * directly. In this case, we need to acquire the EEPROM so that - * FW or other port software does not interrupt. - */ - if (em_is_onboard_nvm_eeprom(hw) == TRUE && - hw->eeprom.use_eerd == FALSE) { - /* Prepare the EEPROM for bit-bang reading */ - if (em_acquire_eeprom(hw) != E1000_SUCCESS) - return -E1000_ERR_EEPROM; - } - - /* Eerd register EEPROM access requires no eeprom aquire/release */ - if (eeprom->use_eerd == TRUE) - return em_read_eeprom_eerd(hw, offset, words, data); - - /* ICH EEPROM access is done via the ICH flash controller */ - if (eeprom->type == em_eeprom_ich8) - return em_read_eeprom_ich8(hw, offset, words, data); - - /* Set up the SPI or Microwire EEPROM for bit-bang reading. We have - * acquired the EEPROM at this point, so any returns should relase it */ - if (eeprom->type == em_eeprom_spi) { - uint16_t word_in; - uint8_t read_opcode = EEPROM_READ_OPCODE_SPI; - - if (em_spi_eeprom_ready(hw)) { - em_release_eeprom(hw); - return -E1000_ERR_EEPROM; - } - - em_standby_eeprom(hw); - - /* Some SPI eeproms use the 8th address bit embedded in the opcode */ - if ((eeprom->address_bits == 8) && (offset >= 128)) - read_opcode |= EEPROM_A8_OPCODE_SPI; - - /* Send the READ command (opcode + addr) */ - em_shift_out_ee_bits(hw, read_opcode, eeprom->opcode_bits); - em_shift_out_ee_bits(hw, (uint16_t)(offset*2), eeprom->address_bits); - - /* Read the data. The address of the eeprom internally increments with - * each byte (spi) being read, saving on the overhead of eeprom setup - * and tear-down. The address counter will roll over if reading beyond - * the size of the eeprom, thus allowing the entire memory to be read - * starting from any offset. */ - for (i = 0; i < words; i++) { - word_in = em_shift_in_ee_bits(hw, 16); - data[i] = (word_in >> 8) | (word_in << 8); - } - } else if (eeprom->type == em_eeprom_microwire) { - for (i = 0; i < words; i++) { - /* Send the READ command (opcode + addr) */ - em_shift_out_ee_bits(hw, EEPROM_READ_OPCODE_MICROWIRE, - eeprom->opcode_bits); - em_shift_out_ee_bits(hw, (uint16_t)(offset + i), - eeprom->address_bits); - - /* Read the data. For microwire, each word requires the overhead - * of eeprom setup and tear-down. */ - data[i] = em_shift_in_ee_bits(hw, 16); - em_standby_eeprom(hw); - } - } - - /* End this read operation */ - em_release_eeprom(hw); - - return E1000_SUCCESS; -} - -/****************************************************************************** - * Reads a 16 bit word from the EEPROM using the EERD register. - * - * hw - Struct containing variables accessed by shared code - * offset - offset of word in the EEPROM to read - * data - word read from the EEPROM - * words - number of words to read - *****************************************************************************/ -STATIC int32_t -em_read_eeprom_eerd(struct em_hw *hw, - uint16_t offset, - uint16_t words, - uint16_t *data) -{ - uint32_t i, eerd = 0; - int32_t error = 0; - - for (i = 0; i < words; i++) { - eerd = ((offset+i) << E1000_EEPROM_RW_ADDR_SHIFT) + - E1000_EEPROM_RW_REG_START; - - E1000_WRITE_REG(hw, EERD, eerd); - error = em_poll_eerd_eewr_done(hw, E1000_EEPROM_POLL_READ); - - if (error) { - break; - } - data[i] = (E1000_READ_REG(hw, EERD) >> E1000_EEPROM_RW_REG_DATA); - - } - - return error; -} - -/****************************************************************************** - * Writes a 16 bit word from the EEPROM using the EEWR register. - * - * hw - Struct containing variables accessed by shared code - * offset - offset of word in the EEPROM to read - * data - word read from the EEPROM - * words - number of words to read - *****************************************************************************/ -STATIC int32_t -em_write_eeprom_eewr(struct em_hw *hw, - uint16_t offset, - uint16_t words, - uint16_t *data) -{ - uint32_t register_value = 0; - uint32_t i = 0; - int32_t error = 0; - - if (em_swfw_sync_acquire(hw, E1000_SWFW_EEP_SM)) - return -E1000_ERR_SWFW_SYNC; - - for (i = 0; i < words; i++) { - register_value = (data[i] << E1000_EEPROM_RW_REG_DATA) | - ((offset+i) << E1000_EEPROM_RW_ADDR_SHIFT) | - E1000_EEPROM_RW_REG_START; - - error = em_poll_eerd_eewr_done(hw, E1000_EEPROM_POLL_WRITE); - if (error) { - break; - } - - E1000_WRITE_REG(hw, EEWR, register_value); - - error = em_poll_eerd_eewr_done(hw, E1000_EEPROM_POLL_WRITE); - - if (error) { - break; - } - } - - em_swfw_sync_release(hw, E1000_SWFW_EEP_SM); - return error; -} - -/****************************************************************************** - * Polls the status bit (bit 1) of the EERD to determine when the read is done. - * - * hw - Struct containing variables accessed by shared code - *****************************************************************************/ -STATIC int32_t -em_poll_eerd_eewr_done(struct em_hw *hw, int eerd) -{ - uint32_t attempts = 100000; - uint32_t i, reg = 0; - int32_t done = E1000_ERR_EEPROM; - - for (i = 0; i < attempts; i++) { - if (eerd == E1000_EEPROM_POLL_READ) - reg = E1000_READ_REG(hw, EERD); - else - reg = E1000_READ_REG(hw, EEWR); - - if (reg & E1000_EEPROM_RW_REG_DONE) { - done = E1000_SUCCESS; - break; - } - usec_delay(5); - } - - return done; -} - -/*************************************************************************** -* Description: Determines if the onboard NVM is FLASH or EEPROM. -* -* hw - Struct containing variables accessed by shared code -****************************************************************************/ -STATIC boolean_t -em_is_onboard_nvm_eeprom(struct em_hw *hw) -{ - uint32_t eecd = 0; - - DEBUGFUNC("em_is_onboard_nvm_eeprom"); - - if (hw->mac_type == em_ich8lan || hw->mac_type == em_ich9lan) - return FALSE; - - if (hw->mac_type == em_82573) { - eecd = E1000_READ_REG(hw, EECD); - - /* Isolate bits 15 & 16 */ - eecd = ((eecd >> 15) & 0x03); - - /* If both bits are set, device is Flash type */ - if (eecd == 0x03) { - return FALSE; - } - } - return TRUE; -} - -/****************************************************************************** - * Verifies that the EEPROM has a valid checksum - * - * hw - Struct containing variables accessed by shared code - * - * Reads the first 64 16 bit words of the EEPROM and sums the values read. - * If the the sum of the 64 16 bit words is 0xBABA, the EEPROM's checksum is - * valid. - *****************************************************************************/ -int32_t -em_validate_eeprom_checksum(struct em_hw *hw) -{ - uint16_t checksum = 0; - uint16_t i, eeprom_data; - - DEBUGFUNC("em_validate_eeprom_checksum"); - - if ((hw->mac_type == em_82573) && - (em_is_onboard_nvm_eeprom(hw) == FALSE)) { - /* Check bit 4 of word 10h. If it is 0, firmware is done updating - * 10h-12h. Checksum may need to be fixed. */ - em_read_eeprom(hw, 0x10, 1, &eeprom_data); - if ((eeprom_data & 0x10) == 0) { - /* Read 0x23 and check bit 15. This bit is a 1 when the checksum - * has already been fixed. If the checksum is still wrong and this - * bit is a 1, we need to return bad checksum. Otherwise, we need - * to set this bit to a 1 and update the checksum. */ - em_read_eeprom(hw, 0x23, 1, &eeprom_data); - if ((eeprom_data & 0x8000) == 0) { - eeprom_data |= 0x8000; - em_write_eeprom(hw, 0x23, 1, &eeprom_data); - em_update_eeprom_checksum(hw); - } - } - } - - if (hw->mac_type == em_ich8lan || hw->mac_type == em_ich9lan) { - /* Drivers must allocate the shadow ram structure for the - * EEPROM checksum to be updated. Otherwise, this bit as well - * as the checksum must both be set correctly for this - * validation to pass. - */ - em_read_eeprom(hw, 0x19, 1, &eeprom_data); - if ((eeprom_data & 0x40) == 0) { - eeprom_data |= 0x40; - em_write_eeprom(hw, 0x19, 1, &eeprom_data); - em_update_eeprom_checksum(hw); - } - } - - for (i = 0; i < (EEPROM_CHECKSUM_REG + 1); i++) { - if (em_read_eeprom(hw, i, 1, &eeprom_data) < 0) { - DEBUGOUT("EEPROM Read Error\n"); - return -E1000_ERR_EEPROM; - } - checksum += eeprom_data; - } - - if (checksum == (uint16_t) EEPROM_SUM) - return E1000_SUCCESS; - else { - DEBUGOUT("EEPROM Checksum Invalid\n"); - return -E1000_ERR_EEPROM; - } -} - -/****************************************************************************** - * Calculates the EEPROM checksum and writes it to the EEPROM - * - * hw - Struct containing variables accessed by shared code - * - * Sums the first 63 16 bit words of the EEPROM. Subtracts the sum from 0xBABA. - * Writes the difference to word offset 63 of the EEPROM. - *****************************************************************************/ -int32_t -em_update_eeprom_checksum(struct em_hw *hw) -{ - uint32_t ctrl_ext; - uint16_t checksum = 0; - uint16_t i, eeprom_data; - - DEBUGFUNC("em_update_eeprom_checksum"); - - for (i = 0; i < EEPROM_CHECKSUM_REG; i++) { - if (em_read_eeprom(hw, i, 1, &eeprom_data) < 0) { - DEBUGOUT("EEPROM Read Error\n"); - return -E1000_ERR_EEPROM; - } - checksum += eeprom_data; - } - checksum = (uint16_t) EEPROM_SUM - checksum; - if (em_write_eeprom(hw, EEPROM_CHECKSUM_REG, 1, &checksum) < 0) { - DEBUGOUT("EEPROM Write Error\n"); - return -E1000_ERR_EEPROM; - } else if (hw->eeprom.type == em_eeprom_flash) { - em_commit_shadow_ram(hw); - } else if (hw->eeprom.type == em_eeprom_ich8) { - em_commit_shadow_ram(hw); - /* Reload the EEPROM, or else modifications will not appear - * until after next adapter reset. */ - ctrl_ext = E1000_READ_REG(hw, CTRL_EXT); - ctrl_ext |= E1000_CTRL_EXT_EE_RST; - E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext); - msec_delay(10); - } - return E1000_SUCCESS; -} - -/****************************************************************************** - * Parent function for writing words to the different EEPROM types. - * - * hw - Struct containing variables accessed by shared code - * offset - offset within the EEPROM to be written to - * words - number of words to write - * data - 16 bit word to be written to the EEPROM - * - * If em_update_eeprom_checksum is not called after this function, the - * EEPROM will most likely contain an invalid checksum. - *****************************************************************************/ -int32_t -em_write_eeprom(struct em_hw *hw, - uint16_t offset, - uint16_t words, - uint16_t *data) -{ - struct em_eeprom_info *eeprom = &hw->eeprom; - int32_t status = 0; - - DEBUGFUNC("em_write_eeprom"); - - /* If eeprom is not yet detected, do so now */ - if (eeprom->word_size == 0) - em_init_eeprom_params(hw); - - /* A check for invalid values: offset too large, too many words, and not - * enough words. - */ - if ((offset >= eeprom->word_size) || (words > eeprom->word_size - offset) || - (words == 0)) { - DEBUGOUT("\"words\" parameter out of bounds\n"); - return -E1000_ERR_EEPROM; - } - - /* 82573 writes only through eewr */ - if (eeprom->use_eewr == TRUE) - return em_write_eeprom_eewr(hw, offset, words, data); - - if (eeprom->type == em_eeprom_ich8) - return em_write_eeprom_ich8(hw, offset, words, data); - - /* Prepare the EEPROM for writing */ - if (em_acquire_eeprom(hw) != E1000_SUCCESS) - return -E1000_ERR_EEPROM; - - if (eeprom->type == em_eeprom_microwire) { - status = em_write_eeprom_microwire(hw, offset, words, data); - } else { - status = em_write_eeprom_spi(hw, offset, words, data); - msec_delay(10); - } - - /* Done with writing */ - em_release_eeprom(hw); - - return status; -} - -/****************************************************************************** - * Writes a 16 bit word to a given offset in an SPI EEPROM. - * - * hw - Struct containing variables accessed by shared code - * offset - offset within the EEPROM to be written to - * words - number of words to write - * data - pointer to array of 8 bit words to be written to the EEPROM - * - *****************************************************************************/ -STATIC int32_t -em_write_eeprom_spi(struct em_hw *hw, - uint16_t offset, - uint16_t words, - uint16_t *data) -{ - struct em_eeprom_info *eeprom = &hw->eeprom; - uint16_t widx = 0; - - DEBUGFUNC("em_write_eeprom_spi"); - - while (widx < words) { - uint8_t write_opcode = EEPROM_WRITE_OPCODE_SPI; - - if (em_spi_eeprom_ready(hw)) return -E1000_ERR_EEPROM; - - em_standby_eeprom(hw); - - /* Send the WRITE ENABLE command (8 bit opcode ) */ - em_shift_out_ee_bits(hw, EEPROM_WREN_OPCODE_SPI, - eeprom->opcode_bits); - - em_standby_eeprom(hw); - - /* Some SPI eeproms use the 8th address bit embedded in the opcode */ - if ((eeprom->address_bits == 8) && (offset >= 128)) - write_opcode |= EEPROM_A8_OPCODE_SPI; - - /* Send the Write command (8-bit opcode + addr) */ - em_shift_out_ee_bits(hw, write_opcode, eeprom->opcode_bits); - - em_shift_out_ee_bits(hw, (uint16_t)((offset + widx)*2), - eeprom->address_bits); - - /* Send the data */ - - /* Loop to allow for up to whole page write (32 bytes) of eeprom */ - while (widx < words) { - uint16_t word_out = data[widx]; - word_out = (word_out >> 8) | (word_out << 8); - em_shift_out_ee_bits(hw, word_out, 16); - widx++; - - /* Some larger eeprom sizes are capable of a 32-byte PAGE WRITE - * operation, while the smaller eeproms are capable of an 8-byte - * PAGE WRITE operation. Break the inner loop to pass new address - */ - if ((((offset + widx)*2) % eeprom->page_size) == 0) { - em_standby_eeprom(hw); - break; - } - } - } - - return E1000_SUCCESS; -} - -/****************************************************************************** - * Writes a 16 bit word to a given offset in a Microwire EEPROM. - * - * hw - Struct containing variables accessed by shared code - * offset - offset within the EEPROM to be written to - * words - number of words to write - * data - pointer to array of 16 bit words to be written to the EEPROM - * - *****************************************************************************/ -STATIC int32_t -em_write_eeprom_microwire(struct em_hw *hw, - uint16_t offset, - uint16_t words, - uint16_t *data) -{ - struct em_eeprom_info *eeprom = &hw->eeprom; - uint32_t eecd; - uint16_t words_written = 0; - uint16_t i = 0; - - DEBUGFUNC("em_write_eeprom_microwire"); - - /* Send the write enable command to the EEPROM (3-bit opcode plus - * 6/8-bit dummy address beginning with 11). It's less work to include - * the 11 of the dummy address as part of the opcode than it is to shift - * it over the correct number of bits for the address. This puts the - * EEPROM into write/erase mode. - */ - em_shift_out_ee_bits(hw, EEPROM_EWEN_OPCODE_MICROWIRE, - (uint16_t)(eeprom->opcode_bits + 2)); - - em_shift_out_ee_bits(hw, 0, (uint16_t)(eeprom->address_bits - 2)); - - /* Prepare the EEPROM */ - em_standby_eeprom(hw); - - while (words_written < words) { - /* Send the Write command (3-bit opcode + addr) */ - em_shift_out_ee_bits(hw, EEPROM_WRITE_OPCODE_MICROWIRE, - eeprom->opcode_bits); - - em_shift_out_ee_bits(hw, (uint16_t)(offset + words_written), - eeprom->address_bits); - - /* Send the data */ - em_shift_out_ee_bits(hw, data[words_written], 16); - - /* Toggle the CS line. This in effect tells the EEPROM to execute - * the previous command. - */ - em_standby_eeprom(hw); - - /* Read DO repeatedly until it is high (equal to '1'). The EEPROM will - * signal that the command has been completed by raising the DO signal. - * If DO does not go high in 10 milliseconds, then error out. - */ - for (i = 0; i < 200; i++) { - eecd = E1000_READ_REG(hw, EECD); - if (eecd & E1000_EECD_DO) break; - usec_delay(50); - } - if (i == 200) { - DEBUGOUT("EEPROM Write did not complete\n"); - return -E1000_ERR_EEPROM; - } - - /* Recover from write */ - em_standby_eeprom(hw); - - words_written++; - } - - /* Send the write disable command to the EEPROM (3-bit opcode plus - * 6/8-bit dummy address beginning with 10). It's less work to include - * the 10 of the dummy address as part of the opcode than it is to shift - * it over the correct number of bits for the address. This takes the - * EEPROM out of write/erase mode. - */ - em_shift_out_ee_bits(hw, EEPROM_EWDS_OPCODE_MICROWIRE, - (uint16_t)(eeprom->opcode_bits + 2)); - - em_shift_out_ee_bits(hw, 0, (uint16_t)(eeprom->address_bits - 2)); - - return E1000_SUCCESS; -} - -/****************************************************************************** - * Flushes the cached eeprom to NVM. This is done by saving the modified values - * in the eeprom cache and the non modified values in the currently active bank - * to the new bank. - * - * hw - Struct containing variables accessed by shared code - * offset - offset of word in the EEPROM to read - * data - word read from the EEPROM - * words - number of words to read - *****************************************************************************/ -STATIC int32_t -em_commit_shadow_ram(struct em_hw *hw) -{ - uint32_t attempts = 100000; - uint32_t eecd = 0; - uint32_t flop = 0; - uint32_t i = 0; - int32_t error = E1000_SUCCESS; - uint32_t old_bank_offset = 0; - uint32_t new_bank_offset = 0; - uint8_t low_byte = 0; - uint8_t high_byte = 0; - boolean_t sector_write_failed = FALSE; - - if (hw->mac_type == em_82573) { - /* The flop register will be used to determine if flash type is STM */ - flop = E1000_READ_REG(hw, FLOP); - for (i=0; i < attempts; i++) { - eecd = E1000_READ_REG(hw, EECD); - if ((eecd & E1000_EECD_FLUPD) == 0) { - break; - } - usec_delay(5); - } - - if (i == attempts) { - return -E1000_ERR_EEPROM; - } - - /* If STM opcode located in bits 15:8 of flop, reset firmware */ - if ((flop & 0xFF00) == E1000_STM_OPCODE) { - E1000_WRITE_REG(hw, HICR, E1000_HICR_FW_RESET); - } - - /* Perform the flash update */ - E1000_WRITE_REG(hw, EECD, eecd | E1000_EECD_FLUPD); - - for (i=0; i < attempts; i++) { - eecd = E1000_READ_REG(hw, EECD); - if ((eecd & E1000_EECD_FLUPD) == 0) { - break; - } - usec_delay(5); - } - - if (i == attempts) { - return -E1000_ERR_EEPROM; - } - } - - if (((hw->mac_type == em_ich8lan) || (hw->mac_type == em_ich9lan)) && - hw->eeprom_shadow_ram != NULL) { - /* We're writing to the opposite bank so if we're on bank 1, - * write to bank 0 etc. We also need to erase the segment that - * is going to be written */ - if (!(E1000_READ_REG(hw, EECD) & E1000_EECD_SEC1VAL)) { - new_bank_offset = hw->flash_bank_size * 2; - old_bank_offset = 0; - em_erase_ich8_4k_segment(hw, 1); - } else { - old_bank_offset = hw->flash_bank_size * 2; - new_bank_offset = 0; - em_erase_ich8_4k_segment(hw, 0); - } - - sector_write_failed = FALSE; - /* Loop for every byte in the shadow RAM, - * which is in units of words. */ - for (i = 0; i < E1000_SHADOW_RAM_WORDS; i++) { - /* Determine whether to write the value stored - * in the other NVM bank or a modified value stored - * in the shadow RAM */ - if (hw->eeprom_shadow_ram[i].modified == TRUE) { - low_byte = (uint8_t)hw->eeprom_shadow_ram[i].eeprom_word; - usec_delay(100); - error = em_verify_write_ich8_byte(hw, - (i << 1) + new_bank_offset, low_byte); - - if (error != E1000_SUCCESS) - sector_write_failed = TRUE; - else { - high_byte = - (uint8_t)(hw->eeprom_shadow_ram[i].eeprom_word >> 8); - usec_delay(100); - } - } else { - em_read_ich8_byte(hw, (i << 1) + old_bank_offset, - &low_byte); - usec_delay(100); - error = em_verify_write_ich8_byte(hw, - (i << 1) + new_bank_offset, low_byte); - - if (error != E1000_SUCCESS) - sector_write_failed = TRUE; - else { - em_read_ich8_byte(hw, (i << 1) + old_bank_offset + 1, - &high_byte); - usec_delay(100); - } - } - - /* If the write of the low byte was successful, go ahread and - * write the high byte while checking to make sure that if it - * is the signature byte, then it is handled properly */ - if (sector_write_failed == FALSE) { - /* If the word is 0x13, then make sure the signature bits - * (15:14) are 11b until the commit has completed. - * This will allow us to write 10b which indicates the - * signature is valid. We want to do this after the write - * has completed so that we don't mark the segment valid - * while the write is still in progress */ - if (i == E1000_ICH_NVM_SIG_WORD) - high_byte = E1000_ICH_NVM_SIG_MASK | high_byte; - - error = em_verify_write_ich8_byte(hw, - (i << 1) + new_bank_offset + 1, high_byte); - if (error != E1000_SUCCESS) - sector_write_failed = TRUE; - - } else { - /* If the write failed then break from the loop and - * return an error */ - break; - } - } - - /* Don't bother writing the segment valid bits if sector - * programming failed. */ - if (sector_write_failed == FALSE) { - /* Finally validate the new segment by setting bit 15:14 - * to 10b in word 0x13 , this can be done without an - * erase as well since these bits are 11 to start with - * and we need to change bit 14 to 0b */ - em_read_ich8_byte(hw, - E1000_ICH_NVM_SIG_WORD * 2 + 1 + new_bank_offset, - &high_byte); - high_byte &= 0xBF; - error = em_verify_write_ich8_byte(hw, - E1000_ICH_NVM_SIG_WORD * 2 + 1 + new_bank_offset, high_byte); - /* And invalidate the previously valid segment by setting - * its signature word (0x13) high_byte to 0b. This can be - * done without an erase because flash erase sets all bits - * to 1's. We can write 1's to 0's without an erase */ - if (error == E1000_SUCCESS) { - error = em_verify_write_ich8_byte(hw, - E1000_ICH_NVM_SIG_WORD * 2 + 1 + old_bank_offset, 0); - } - - /* Clear the now not used entry in the cache */ - for (i = 0; i < E1000_SHADOW_RAM_WORDS; i++) { - hw->eeprom_shadow_ram[i].modified = FALSE; - hw->eeprom_shadow_ram[i].eeprom_word = 0xFFFF; - } - } - } - - return error; -} - -/****************************************************************************** - * Reads the adapter's part number from the EEPROM - * - * hw - Struct containing variables accessed by shared code - * part_num - Adapter's part number - *****************************************************************************/ -int32_t -em_read_part_num(struct em_hw *hw, - uint32_t *part_num) -{ - uint16_t offset = EEPROM_PBA_BYTE_1; - uint16_t eeprom_data; - - DEBUGFUNC("em_read_part_num"); - - /* Get word 0 from EEPROM */ - if (em_read_eeprom(hw, offset, 1, &eeprom_data) < 0) { - DEBUGOUT("EEPROM Read Error\n"); - return -E1000_ERR_EEPROM; - } - /* Save word 0 in upper half of part_num */ - *part_num = (uint32_t) (eeprom_data << 16); - - /* Get word 1 from EEPROM */ - if (em_read_eeprom(hw, ++offset, 1, &eeprom_data) < 0) { - DEBUGOUT("EEPROM Read Error\n"); - return -E1000_ERR_EEPROM; - } - /* Save word 1 in lower half of part_num */ - *part_num |= eeprom_data; - - return E1000_SUCCESS; -} - -/****************************************************************************** - * Reads the adapter's MAC address from the EEPROM and inverts the LSB for the - * second function of dual function devices - * - * hw - Struct containing variables accessed by shared code - *****************************************************************************/ -int32_t -em_read_mac_addr(struct em_hw * hw) -{ - uint16_t offset; - uint16_t eeprom_data, i; - - DEBUGFUNC("em_read_mac_addr"); - - for (i = 0; i < NODE_ADDRESS_SIZE; i += 2) { - offset = i >> 1; - if (em_read_eeprom(hw, offset, 1, &eeprom_data) < 0) { - DEBUGOUT("EEPROM Read Error\n"); - return -E1000_ERR_EEPROM; - } - hw->perm_mac_addr[i] = (uint8_t) (eeprom_data & 0x00FF); - hw->perm_mac_addr[i+1] = (uint8_t) (eeprom_data >> 8); - } - - switch (hw->mac_type) { - default: - break; - case em_82546: - case em_82546_rev_3: - case em_82571: - case em_80003es2lan: - if (E1000_READ_REG(hw, STATUS) & E1000_STATUS_FUNC_1) - hw->perm_mac_addr[5] ^= 0x01; - break; - } - - for (i = 0; i < NODE_ADDRESS_SIZE; i++) - hw->mac_addr[i] = hw->perm_mac_addr[i]; - return E1000_SUCCESS; -} - -/****************************************************************************** - * Initializes receive address filters. - * - * hw - Struct containing variables accessed by shared code - * - * Places the MAC address in receive address register 0 and clears the rest - * of the receive addresss registers. Clears the multicast table. Assumes - * the receiver is in reset when the routine is called. - *****************************************************************************/ -STATIC void -em_init_rx_addrs(struct em_hw *hw) -{ - uint32_t i; - uint32_t rar_num; - - DEBUGFUNC("em_init_rx_addrs"); - - /* Setup the receive address. */ - DEBUGOUT("Programming MAC Address into RAR[0]\n"); - - em_rar_set(hw, hw->mac_addr, 0); - - rar_num = E1000_RAR_ENTRIES; - - /* Reserve a spot for the Locally Administered Address to work around - * an 82571 issue in which a reset on one port will reload the MAC on - * the other port. */ - if ((hw->mac_type == em_82571) && (hw->laa_is_present == TRUE)) - rar_num -= 1; - if (hw->mac_type == em_ich8lan || hw->mac_type == em_ich9lan) - rar_num = E1000_RAR_ENTRIES_ICH8LAN; - - /* Zero out the other 15 receive addresses. */ - DEBUGOUT("Clearing RAR[1-15]\n"); - for (i = 1; i < rar_num; i++) { - E1000_WRITE_REG_ARRAY(hw, RA, (i << 1), 0); - E1000_WRITE_FLUSH(hw); - E1000_WRITE_REG_ARRAY(hw, RA, ((i << 1) + 1), 0); - E1000_WRITE_FLUSH(hw); - } -} - -/****************************************************************************** - * Updates the MAC's list of multicast addresses. - * - * hw - Struct containing variables accessed by shared code - * mc_addr_list - the list of new multicast addresses - * mc_addr_count - number of addresses - * pad - number of bytes between addresses in the list - * rar_used_count - offset where to start adding mc addresses into the RAR's - * - * The given list replaces any existing list. Clears the last 15 receive - * address registers and the multicast table. Uses receive address registers - * for the first 15 multicast addresses, and hashes the rest into the - * multicast table. - *****************************************************************************/ -void -em_mc_addr_list_update(struct em_hw *hw, - uint8_t *mc_addr_list, - uint32_t mc_addr_count, - uint32_t pad, - uint32_t rar_used_count) -{ - uint32_t hash_value; - uint32_t i; - uint32_t num_rar_entry; - uint32_t num_mta_entry; - - DEBUGFUNC("em_mc_addr_list_update"); - - /* Set the new number of MC addresses that we are being requested to use. */ - hw->num_mc_addrs = mc_addr_count; - - /* Clear RAR[1-15] */ - DEBUGOUT(" Clearing RAR[1-15]\n"); - num_rar_entry = E1000_RAR_ENTRIES; - if (hw->mac_type == em_ich8lan || hw->mac_type == em_ich9lan) - num_rar_entry = E1000_RAR_ENTRIES_ICH8LAN; - - /* Reserve a spot for the Locally Administered Address to work around - * an 82571 issue in which a reset on one port will reload the MAC on - * the other port. */ - if ((hw->mac_type == em_82571) && (hw->laa_is_present == TRUE)) - num_rar_entry -= 1; - - for (i = rar_used_count; i < num_rar_entry; i++) { - E1000_WRITE_REG_ARRAY(hw, RA, (i << 1), 0); - E1000_WRITE_FLUSH(hw); - E1000_WRITE_REG_ARRAY(hw, RA, ((i << 1) + 1), 0); - E1000_WRITE_FLUSH(hw); - } - - /* Clear the MTA */ - DEBUGOUT(" Clearing MTA\n"); - num_mta_entry = E1000_NUM_MTA_REGISTERS; - if (hw->mac_type == em_ich8lan || hw->mac_type == em_ich9lan) - num_mta_entry = E1000_NUM_MTA_REGISTERS_ICH8LAN; - - for (i = 0; i < num_mta_entry; i++) { - E1000_WRITE_REG_ARRAY(hw, MTA, i, 0); - E1000_WRITE_FLUSH(hw); - } - - /* Add the new addresses */ - for (i = 0; i < mc_addr_count; i++) { - DEBUGOUT(" Adding the multicast addresses:\n"); - DEBUGOUT7(" MC Addr #%d =%.2X %.2X %.2X %.2X %.2X %.2X\n", i, - mc_addr_list[i * (ETH_LENGTH_OF_ADDRESS + pad)], - mc_addr_list[i * (ETH_LENGTH_OF_ADDRESS + pad) + 1], - mc_addr_list[i * (ETH_LENGTH_OF_ADDRESS + pad) + 2], - mc_addr_list[i * (ETH_LENGTH_OF_ADDRESS + pad) + 3], - mc_addr_list[i * (ETH_LENGTH_OF_ADDRESS + pad) + 4], - mc_addr_list[i * (ETH_LENGTH_OF_ADDRESS + pad) + 5]); - - hash_value = em_hash_mc_addr(hw, - mc_addr_list + - (i * (ETH_LENGTH_OF_ADDRESS + pad))); - - DEBUGOUT1(" Hash value = 0x%03X\n", hash_value); - - /* Place this multicast address in the RAR if there is room, * - * else put it in the MTA - */ - if (rar_used_count < num_rar_entry) { - em_rar_set(hw, - mc_addr_list + (i * (ETH_LENGTH_OF_ADDRESS + pad)), - rar_used_count); - rar_used_count++; - } else { - em_mta_set(hw, hash_value); - } - } - DEBUGOUT("MC Update Complete\n"); -} - -/****************************************************************************** - * Hashes an address to determine its location in the multicast table - * - * hw - Struct containing variables accessed by shared code - * mc_addr - the multicast address to hash - *****************************************************************************/ -uint32_t -em_hash_mc_addr(struct em_hw *hw, - uint8_t *mc_addr) -{ - uint32_t hash_value = 0; - - /* The portion of the address that is used for the hash table is - * determined by the mc_filter_type setting. - */ - switch (hw->mc_filter_type) { - /* [0] [1] [2] [3] [4] [5] - * 01 AA 00 12 34 56 - * LSB MSB - */ - case 0: - if (hw->mac_type == em_ich8lan || hw->mac_type == em_ich9lan) { - /* [47:38] i.e. 0x158 for above example address */ - hash_value = ((mc_addr[4] >> 6) | (((uint16_t) mc_addr[5]) << 2)); - } else { - /* [47:36] i.e. 0x563 for above example address */ - hash_value = ((mc_addr[4] >> 4) | (((uint16_t) mc_addr[5]) << 4)); - } - break; - case 1: - if (hw->mac_type == em_ich8lan || hw->mac_type == em_ich9lan) { - /* [46:37] i.e. 0x2B1 for above example address */ - hash_value = ((mc_addr[4] >> 5) | (((uint16_t) mc_addr[5]) << 3)); - } else { - /* [46:35] i.e. 0xAC6 for above example address */ - hash_value = ((mc_addr[4] >> 3) | (((uint16_t) mc_addr[5]) << 5)); - } - break; - case 2: - if (hw->mac_type == em_ich8lan || hw->mac_type == em_ich9lan) { - /*[45:36] i.e. 0x163 for above example address */ - hash_value = ((mc_addr[4] >> 4) | (((uint16_t) mc_addr[5]) << 4)); - } else { - /* [45:34] i.e. 0x5D8 for above example address */ - hash_value = ((mc_addr[4] >> 2) | (((uint16_t) mc_addr[5]) << 6)); - } - break; - case 3: - if (hw->mac_type == em_ich8lan || hw->mac_type == em_ich9lan) { - /* [43:34] i.e. 0x18D for above example address */ - hash_value = ((mc_addr[4] >> 2) | (((uint16_t) mc_addr[5]) << 6)); - } else { - /* [43:32] i.e. 0x634 for above example address */ - hash_value = ((mc_addr[4]) | (((uint16_t) mc_addr[5]) << 8)); - } - break; - } - - hash_value &= 0xFFF; - if (hw->mac_type == em_ich8lan || hw->mac_type == em_ich9lan) - hash_value &= 0x3FF; - - return hash_value; -} - -/****************************************************************************** - * Sets the bit in the multicast table corresponding to the hash value. - * - * hw - Struct containing variables accessed by shared code - * hash_value - Multicast address hash value - *****************************************************************************/ -void -em_mta_set(struct em_hw *hw, - uint32_t hash_value) -{ - uint32_t hash_bit, hash_reg; - uint32_t mta; - uint32_t temp; - - /* The MTA is a register array of 128 32-bit registers. - * It is treated like an array of 4096 bits. We want to set - * bit BitArray[hash_value]. So we figure out what register - * the bit is in, read it, OR in the new bit, then write - * back the new value. The register is determined by the - * upper 7 bits of the hash value and the bit within that - * register are determined by the lower 5 bits of the value. - */ - hash_reg = (hash_value >> 5) & 0x7F; - if (hw->mac_type == em_ich8lan || hw->mac_type == em_ich9lan) - hash_reg &= 0x1F; - - hash_bit = hash_value & 0x1F; - - mta = E1000_READ_REG_ARRAY(hw, MTA, hash_reg); - - mta |= (1 << hash_bit); - - /* If we are on an 82544 and we are trying to write an odd offset - * in the MTA, save off the previous entry before writing and - * restore the old value after writing. - */ - if ((hw->mac_type == em_82544) && ((hash_reg & 0x1) == 1)) { - temp = E1000_READ_REG_ARRAY(hw, MTA, (hash_reg - 1)); - E1000_WRITE_REG_ARRAY(hw, MTA, hash_reg, mta); - E1000_WRITE_FLUSH(hw); - E1000_WRITE_REG_ARRAY(hw, MTA, (hash_reg - 1), temp); - E1000_WRITE_FLUSH(hw); - } else { - E1000_WRITE_REG_ARRAY(hw, MTA, hash_reg, mta); - E1000_WRITE_FLUSH(hw); - } -} - -/****************************************************************************** - * Puts an ethernet address into a receive address register. - * - * hw - Struct containing variables accessed by shared code - * addr - Address to put into receive address register - * index - Receive address register to write - *****************************************************************************/ -void -em_rar_set(struct em_hw *hw, - uint8_t *addr, - uint32_t index) -{ - uint32_t rar_low, rar_high; - - /* HW expects these in little endian so we reverse the byte order - * from network order (big endian) to little endian - */ - rar_low = ((uint32_t) addr[0] | - ((uint32_t) addr[1] << 8) | - ((uint32_t) addr[2] << 16) | ((uint32_t) addr[3] << 24)); - rar_high = ((uint32_t) addr[4] | ((uint32_t) addr[5] << 8)); - - /* Disable Rx and flush all Rx frames before enabling RSS to avoid Rx - * unit hang. - * - * Description: - * If there are any Rx frames queued up or otherwise present in the HW - * before RSS is enabled, and then we enable RSS, the HW Rx unit will - * hang. To work around this issue, we have to disable receives and - * flush out all Rx frames before we enable RSS. To do so, we modify we - * redirect all Rx traffic to manageability and then reset the HW. - * This flushes away Rx frames, and (since the redirections to - * manageability persists across resets) keeps new ones from coming in - * while we work. Then, we clear the Address Valid AV bit for all MAC - * addresses and undo the re-direction to manageability. - * Now, frames are coming in again, but the MAC won't accept them, so - * far so good. We now proceed to initialize RSS (if necessary) and - * configure the Rx unit. Last, we re-enable the AV bits and continue - * on our merry way. - */ - switch (hw->mac_type) { - case em_82571: - case em_82572: - case em_80003es2lan: - if (hw->leave_av_bit_off == TRUE) - break; - default: - /* Indicate to hardware the Address is Valid. */ - rar_high |= E1000_RAH_AV; - break; - } - - E1000_WRITE_REG_ARRAY(hw, RA, (index << 1), rar_low); - E1000_WRITE_FLUSH(hw); - E1000_WRITE_REG_ARRAY(hw, RA, ((index << 1) + 1), rar_high); - E1000_WRITE_FLUSH(hw); -} - -/****************************************************************************** - * Writes a value to the specified offset in the VLAN filter table. - * - * hw - Struct containing variables accessed by shared code - * offset - Offset in VLAN filer table to write - * value - Value to write into VLAN filter table - *****************************************************************************/ -void -em_write_vfta(struct em_hw *hw, - uint32_t offset, - uint32_t value) -{ - uint32_t temp; - - if (hw->mac_type == em_ich8lan || hw->mac_type == em_ich9lan) - return; - - if ((hw->mac_type == em_82544) && ((offset & 0x1) == 1)) { - temp = E1000_READ_REG_ARRAY(hw, VFTA, (offset - 1)); - E1000_WRITE_REG_ARRAY(hw, VFTA, offset, value); - E1000_WRITE_FLUSH(hw); - E1000_WRITE_REG_ARRAY(hw, VFTA, (offset - 1), temp); - E1000_WRITE_FLUSH(hw); - } else { - E1000_WRITE_REG_ARRAY(hw, VFTA, offset, value); - E1000_WRITE_FLUSH(hw); - } -} - -/****************************************************************************** - * Clears the VLAN filer table - * - * hw - Struct containing variables accessed by shared code - *****************************************************************************/ -STATIC void -em_clear_vfta(struct em_hw *hw) -{ - uint32_t offset; - uint32_t vfta_value = 0; - uint32_t vfta_offset = 0; - uint32_t vfta_bit_in_reg = 0; - - if (hw->mac_type == em_ich8lan || hw->mac_type == em_ich9lan) - return; - - if (hw->mac_type == em_82573) { - if (hw->mng_cookie.vlan_id != 0) { - /* The VFTA is a 4096b bit-field, each identifying a single VLAN - * ID. The following operations determine which 32b entry - * (i.e. offset) into the array we want to set the VLAN ID - * (i.e. bit) of the manageability unit. */ - vfta_offset = (hw->mng_cookie.vlan_id >> - E1000_VFTA_ENTRY_SHIFT) & - E1000_VFTA_ENTRY_MASK; - vfta_bit_in_reg = 1 << (hw->mng_cookie.vlan_id & - E1000_VFTA_ENTRY_BIT_SHIFT_MASK); - } - } - for (offset = 0; offset < E1000_VLAN_FILTER_TBL_SIZE; offset++) { - /* If the offset we want to clear is the same offset of the - * manageability VLAN ID, then clear all bits except that of the - * manageability unit */ - vfta_value = (offset == vfta_offset) ? vfta_bit_in_reg : 0; - E1000_WRITE_REG_ARRAY(hw, VFTA, offset, vfta_value); - E1000_WRITE_FLUSH(hw); - } -} - -STATIC int32_t -em_id_led_init(struct em_hw * hw) -{ - uint32_t ledctl; - const uint32_t ledctl_mask = 0x000000FF; - const uint32_t ledctl_on = E1000_LEDCTL_MODE_LED_ON; - const uint32_t ledctl_off = E1000_LEDCTL_MODE_LED_OFF; - uint16_t eeprom_data, i, temp; - const uint16_t led_mask = 0x0F; - - DEBUGFUNC("em_id_led_init"); - - if (hw->mac_type < em_82540) { - /* Nothing to do */ - return E1000_SUCCESS; - } - - ledctl = E1000_READ_REG(hw, LEDCTL); - hw->ledctl_default = ledctl; - hw->ledctl_mode1 = hw->ledctl_default; - hw->ledctl_mode2 = hw->ledctl_default; - - if (em_read_eeprom(hw, EEPROM_ID_LED_SETTINGS, 1, &eeprom_data) < 0) { - DEBUGOUT("EEPROM Read Error\n"); - return -E1000_ERR_EEPROM; - } - - if ((hw->mac_type == em_82573) && - (eeprom_data == ID_LED_RESERVED_82573)) - eeprom_data = ID_LED_DEFAULT_82573; - else if ((eeprom_data == ID_LED_RESERVED_0000) || - (eeprom_data == ID_LED_RESERVED_FFFF)) { - if (hw->mac_type == em_ich8lan || hw->mac_type == em_ich9lan) - eeprom_data = ID_LED_DEFAULT_ICH8LAN; - else - eeprom_data = ID_LED_DEFAULT; - } - - for (i = 0; i < 4; i++) { - temp = (eeprom_data >> (i << 2)) & led_mask; - switch (temp) { - case ID_LED_ON1_DEF2: - case ID_LED_ON1_ON2: - case ID_LED_ON1_OFF2: - hw->ledctl_mode1 &= ~(ledctl_mask << (i << 3)); - hw->ledctl_mode1 |= ledctl_on << (i << 3); - break; - case ID_LED_OFF1_DEF2: - case ID_LED_OFF1_ON2: - case ID_LED_OFF1_OFF2: - hw->ledctl_mode1 &= ~(ledctl_mask << (i << 3)); - hw->ledctl_mode1 |= ledctl_off << (i << 3); - break; - default: - /* Do nothing */ - break; - } - switch (temp) { - case ID_LED_DEF1_ON2: - case ID_LED_ON1_ON2: - case ID_LED_OFF1_ON2: - hw->ledctl_mode2 &= ~(ledctl_mask << (i << 3)); - hw->ledctl_mode2 |= ledctl_on << (i << 3); - break; - case ID_LED_DEF1_OFF2: - case ID_LED_ON1_OFF2: - case ID_LED_OFF1_OFF2: - hw->ledctl_mode2 &= ~(ledctl_mask << (i << 3)); - hw->ledctl_mode2 |= ledctl_off << (i << 3); - break; - default: - /* Do nothing */ - break; - } - } - return E1000_SUCCESS; -} - -/****************************************************************************** - * Prepares SW controlable LED for use and saves the current state of the LED. - * - * hw - Struct containing variables accessed by shared code - *****************************************************************************/ -int32_t -em_setup_led(struct em_hw *hw) -{ - uint32_t ledctl; - int32_t ret_val = E1000_SUCCESS; - - DEBUGFUNC("em_setup_led"); - - switch (hw->mac_type) { - case em_82542_rev2_0: - case em_82542_rev2_1: - case em_82543: - case em_82544: - /* No setup necessary */ - break; - case em_82541: - case em_82547: - case em_82541_rev_2: - case em_82547_rev_2: - /* Turn off PHY Smart Power Down (if enabled) */ - ret_val = em_read_phy_reg(hw, IGP01E1000_GMII_FIFO, - &hw->phy_spd_default); - if (ret_val) - return ret_val; - ret_val = em_write_phy_reg(hw, IGP01E1000_GMII_FIFO, - (uint16_t)(hw->phy_spd_default & - ~IGP01E1000_GMII_SPD)); - if (ret_val) - return ret_val; - /* Fall Through */ - default: - if (hw->media_type == em_media_type_fiber) { - ledctl = E1000_READ_REG(hw, LEDCTL); - /* Save current LEDCTL settings */ - hw->ledctl_default = ledctl; - /* Turn off LED0 */ - ledctl &= ~(E1000_LEDCTL_LED0_IVRT | - E1000_LEDCTL_LED0_BLINK | - E1000_LEDCTL_LED0_MODE_MASK); - ledctl |= (E1000_LEDCTL_MODE_LED_OFF << - E1000_LEDCTL_LED0_MODE_SHIFT); - E1000_WRITE_REG(hw, LEDCTL, ledctl); - } else if (hw->media_type == em_media_type_copper) - E1000_WRITE_REG(hw, LEDCTL, hw->ledctl_mode1); - break; - } - - return E1000_SUCCESS; -} - - -/****************************************************************************** - * Used on 82571 and later Si that has LED blink bits. - * Callers must use their own timer and should have already called - * em_id_led_init() - * Call em_cleanup led() to stop blinking - * - * hw - Struct containing variables accessed by shared code - *****************************************************************************/ -int32_t -em_blink_led_start(struct em_hw *hw) -{ - int16_t i; - uint32_t ledctl_blink = 0; - - DEBUGFUNC("em_id_led_blink_on"); - - if (hw->mac_type < em_82571) { - /* Nothing to do */ - return E1000_SUCCESS; - } - if (hw->media_type == em_media_type_fiber) { - /* always blink LED0 for PCI-E fiber */ - ledctl_blink = E1000_LEDCTL_LED0_BLINK | - (E1000_LEDCTL_MODE_LED_ON << E1000_LEDCTL_LED0_MODE_SHIFT); - } else { - /* set the blink bit for each LED that's "on" (0x0E) in ledctl_mode2 */ - ledctl_blink = hw->ledctl_mode2; - for (i=0; i < 4; i++) - if (((hw->ledctl_mode2 >> (i * 8)) & 0xFF) == - E1000_LEDCTL_MODE_LED_ON) - ledctl_blink |= (E1000_LEDCTL_LED0_BLINK << (i * 8)); - } - - E1000_WRITE_REG(hw, LEDCTL, ledctl_blink); - - return E1000_SUCCESS; -} - -/****************************************************************************** - * Restores the saved state of the SW controlable LED. - * - * hw - Struct containing variables accessed by shared code - *****************************************************************************/ -int32_t -em_cleanup_led(struct em_hw *hw) -{ - int32_t ret_val = E1000_SUCCESS; - - DEBUGFUNC("em_cleanup_led"); - - switch (hw->mac_type) { - case em_82542_rev2_0: - case em_82542_rev2_1: - case em_82543: - case em_82544: - /* No cleanup necessary */ - break; - case em_82541: - case em_82547: - case em_82541_rev_2: - case em_82547_rev_2: - /* Turn on PHY Smart Power Down (if previously enabled) */ - ret_val = em_write_phy_reg(hw, IGP01E1000_GMII_FIFO, - hw->phy_spd_default); - if (ret_val) - return ret_val; - /* Fall Through */ - default: - if (hw->phy_type == em_phy_ife) { - em_write_phy_reg(hw, IFE_PHY_SPECIAL_CONTROL_LED, 0); - break; - } - /* Restore LEDCTL settings */ - E1000_WRITE_REG(hw, LEDCTL, hw->ledctl_default); - break; - } - - return E1000_SUCCESS; -} - -/****************************************************************************** - * Turns on the software controllable LED - * - * hw - Struct containing variables accessed by shared code - *****************************************************************************/ -int32_t -em_led_on(struct em_hw *hw) -{ - uint32_t ctrl = E1000_READ_REG(hw, CTRL); - - DEBUGFUNC("em_led_on"); - - switch (hw->mac_type) { - case em_82542_rev2_0: - case em_82542_rev2_1: - case em_82543: - /* Set SW Defineable Pin 0 to turn on the LED */ - ctrl |= E1000_CTRL_SWDPIN0; - ctrl |= E1000_CTRL_SWDPIO0; - break; - case em_82544: - if (hw->media_type == em_media_type_fiber) { - /* Set SW Defineable Pin 0 to turn on the LED */ - ctrl |= E1000_CTRL_SWDPIN0; - ctrl |= E1000_CTRL_SWDPIO0; - } else { - /* Clear SW Defineable Pin 0 to turn on the LED */ - ctrl &= ~E1000_CTRL_SWDPIN0; - ctrl |= E1000_CTRL_SWDPIO0; - } - break; - default: - if (hw->media_type == em_media_type_fiber) { - /* Clear SW Defineable Pin 0 to turn on the LED */ - ctrl &= ~E1000_CTRL_SWDPIN0; - ctrl |= E1000_CTRL_SWDPIO0; - } else if (hw->phy_type == em_phy_ife) { - em_write_phy_reg(hw, IFE_PHY_SPECIAL_CONTROL_LED, - (IFE_PSCL_PROBE_MODE | IFE_PSCL_PROBE_LEDS_ON)); - } else if (hw->media_type == em_media_type_copper) { - E1000_WRITE_REG(hw, LEDCTL, hw->ledctl_mode2); - return E1000_SUCCESS; - } - break; - } - - E1000_WRITE_REG(hw, CTRL, ctrl); - - return E1000_SUCCESS; -} - -/****************************************************************************** - * Turns off the software controllable LED - * - * hw - Struct containing variables accessed by shared code - *****************************************************************************/ -int32_t -em_led_off(struct em_hw *hw) -{ - uint32_t ctrl = E1000_READ_REG(hw, CTRL); - - DEBUGFUNC("em_led_off"); - - switch (hw->mac_type) { - case em_82542_rev2_0: - case em_82542_rev2_1: - case em_82543: - /* Clear SW Defineable Pin 0 to turn off the LED */ - ctrl &= ~E1000_CTRL_SWDPIN0; - ctrl |= E1000_CTRL_SWDPIO0; - break; - case em_82544: - if (hw->media_type == em_media_type_fiber) { - /* Clear SW Defineable Pin 0 to turn off the LED */ - ctrl &= ~E1000_CTRL_SWDPIN0; - ctrl |= E1000_CTRL_SWDPIO0; - } else { - /* Set SW Defineable Pin 0 to turn off the LED */ - ctrl |= E1000_CTRL_SWDPIN0; - ctrl |= E1000_CTRL_SWDPIO0; - } - break; - default: - if (hw->media_type == em_media_type_fiber) { - /* Set SW Defineable Pin 0 to turn off the LED */ - ctrl |= E1000_CTRL_SWDPIN0; - ctrl |= E1000_CTRL_SWDPIO0; - } else if (hw->phy_type == em_phy_ife) { - em_write_phy_reg(hw, IFE_PHY_SPECIAL_CONTROL_LED, - (IFE_PSCL_PROBE_MODE | IFE_PSCL_PROBE_LEDS_OFF)); - } else if (hw->media_type == em_media_type_copper) { - E1000_WRITE_REG(hw, LEDCTL, hw->ledctl_mode1); - return E1000_SUCCESS; - } - break; - } - - E1000_WRITE_REG(hw, CTRL, ctrl); - - return E1000_SUCCESS; -} - -/****************************************************************************** - * Clears all hardware statistics counters. - * - * hw - Struct containing variables accessed by shared code - *****************************************************************************/ -void -em_clear_hw_cntrs(struct em_hw *hw) -{ - volatile uint32_t temp; - - temp = E1000_READ_REG(hw, CRCERRS); - temp = E1000_READ_REG(hw, SYMERRS); - temp = E1000_READ_REG(hw, MPC); - temp = E1000_READ_REG(hw, SCC); - temp = E1000_READ_REG(hw, ECOL); - temp = E1000_READ_REG(hw, MCC); - temp = E1000_READ_REG(hw, LATECOL); - temp = E1000_READ_REG(hw, COLC); - temp = E1000_READ_REG(hw, DC); - temp = E1000_READ_REG(hw, SEC); - temp = E1000_READ_REG(hw, RLEC); - temp = E1000_READ_REG(hw, XONRXC); - temp = E1000_READ_REG(hw, XONTXC); - temp = E1000_READ_REG(hw, XOFFRXC); - temp = E1000_READ_REG(hw, XOFFTXC); - temp = E1000_READ_REG(hw, FCRUC); - - if (hw->mac_type != em_ich8lan && hw->mac_type != em_ich9lan) { - temp = E1000_READ_REG(hw, PRC64); - temp = E1000_READ_REG(hw, PRC127); - temp = E1000_READ_REG(hw, PRC255); - temp = E1000_READ_REG(hw, PRC511); - temp = E1000_READ_REG(hw, PRC1023); - temp = E1000_READ_REG(hw, PRC1522); - } - - temp = E1000_READ_REG(hw, GPRC); - temp = E1000_READ_REG(hw, BPRC); - temp = E1000_READ_REG(hw, MPRC); - temp = E1000_READ_REG(hw, GPTC); - temp = E1000_READ_REG(hw, GORCL); - temp = E1000_READ_REG(hw, GORCH); - temp = E1000_READ_REG(hw, GOTCL); - temp = E1000_READ_REG(hw, GOTCH); - temp = E1000_READ_REG(hw, RNBC); - temp = E1000_READ_REG(hw, RUC); - temp = E1000_READ_REG(hw, RFC); - temp = E1000_READ_REG(hw, ROC); - temp = E1000_READ_REG(hw, RJC); - temp = E1000_READ_REG(hw, TORL); - temp = E1000_READ_REG(hw, TORH); - temp = E1000_READ_REG(hw, TOTL); - temp = E1000_READ_REG(hw, TOTH); - temp = E1000_READ_REG(hw, TPR); - temp = E1000_READ_REG(hw, TPT); - - if (hw->mac_type != em_ich8lan && hw->mac_type != em_ich9lan) { - temp = E1000_READ_REG(hw, PTC64); - temp = E1000_READ_REG(hw, PTC127); - temp = E1000_READ_REG(hw, PTC255); - temp = E1000_READ_REG(hw, PTC511); - temp = E1000_READ_REG(hw, PTC1023); - temp = E1000_READ_REG(hw, PTC1522); - } - - temp = E1000_READ_REG(hw, MPTC); - temp = E1000_READ_REG(hw, BPTC); - - if (hw->mac_type < em_82543) return; - - temp = E1000_READ_REG(hw, ALGNERRC); - temp = E1000_READ_REG(hw, RXERRC); - temp = E1000_READ_REG(hw, TNCRS); - temp = E1000_READ_REG(hw, CEXTERR); - temp = E1000_READ_REG(hw, TSCTC); - temp = E1000_READ_REG(hw, TSCTFC); - - if (hw->mac_type <= em_82544) return; - - temp = E1000_READ_REG(hw, MGTPRC); - temp = E1000_READ_REG(hw, MGTPDC); - temp = E1000_READ_REG(hw, MGTPTC); - - if (hw->mac_type <= em_82547_rev_2) return; - - temp = E1000_READ_REG(hw, IAC); - temp = E1000_READ_REG(hw, ICRXOC); - - if (hw->mac_type == em_ich8lan || hw->mac_type == em_ich9lan) return; - - temp = E1000_READ_REG(hw, ICRXPTC); - temp = E1000_READ_REG(hw, ICRXATC); - temp = E1000_READ_REG(hw, ICTXPTC); - temp = E1000_READ_REG(hw, ICTXATC); - temp = E1000_READ_REG(hw, ICTXQEC); - temp = E1000_READ_REG(hw, ICTXQMTC); - temp = E1000_READ_REG(hw, ICRXDMTC); - -} - -/****************************************************************************** - * Resets Adaptive IFS to its default state. - * - * hw - Struct containing variables accessed by shared code - * - * Call this after em_init_hw. You may override the IFS defaults by setting - * hw->ifs_params_forced to TRUE. However, you must initialize hw-> - * current_ifs_val, ifs_min_val, ifs_max_val, ifs_step_size, and ifs_ratio - * before calling this function. - *****************************************************************************/ -void -em_reset_adaptive(struct em_hw *hw) -{ - DEBUGFUNC("em_reset_adaptive"); - - if (hw->adaptive_ifs) { - if (!hw->ifs_params_forced) { - hw->current_ifs_val = 0; - hw->ifs_min_val = IFS_MIN; - hw->ifs_max_val = IFS_MAX; - hw->ifs_step_size = IFS_STEP; - hw->ifs_ratio = IFS_RATIO; - } - hw->in_ifs_mode = FALSE; - E1000_WRITE_REG(hw, AIT, 0); - } else { - DEBUGOUT("Not in Adaptive IFS mode!\n"); - } -} - -/****************************************************************************** - * Called during the callback/watchdog routine to update IFS value based on - * the ratio of transmits to collisions. - * - * hw - Struct containing variables accessed by shared code - * tx_packets - Number of transmits since last callback - * total_collisions - Number of collisions since last callback - *****************************************************************************/ -void -em_update_adaptive(struct em_hw *hw) -{ - DEBUGFUNC("em_update_adaptive"); - - if (hw->adaptive_ifs) { - if ((hw->collision_delta * hw->ifs_ratio) > hw->tx_packet_delta) { - if (hw->tx_packet_delta > MIN_NUM_XMITS) { - hw->in_ifs_mode = TRUE; - if (hw->current_ifs_val < hw->ifs_max_val) { - if (hw->current_ifs_val == 0) - hw->current_ifs_val = hw->ifs_min_val; - else - hw->current_ifs_val += hw->ifs_step_size; - E1000_WRITE_REG(hw, AIT, hw->current_ifs_val); - } - } - } else { - if (hw->in_ifs_mode && (hw->tx_packet_delta <= MIN_NUM_XMITS)) { - hw->current_ifs_val = 0; - hw->in_ifs_mode = FALSE; - E1000_WRITE_REG(hw, AIT, 0); - } - } - } else { - DEBUGOUT("Not in Adaptive IFS mode!\n"); - } -} - -/****************************************************************************** - * Adjusts the statistic counters when a frame is accepted by TBI_ACCEPT - * - * hw - Struct containing variables accessed by shared code - * frame_len - The length of the frame in question - * mac_addr - The Ethernet destination address of the frame in question - *****************************************************************************/ -void -em_tbi_adjust_stats(struct em_hw *hw, - struct em_hw_stats *stats, - uint32_t frame_len, - uint8_t *mac_addr) -{ - uint64_t carry_bit; - - /* First adjust the frame length. */ - frame_len--; - /* We need to adjust the statistics counters, since the hardware - * counters overcount this packet as a CRC error and undercount - * the packet as a good packet - */ - /* This packet should not be counted as a CRC error. */ - stats->crcerrs--; - /* This packet does count as a Good Packet Received. */ - stats->gprc++; - - /* Adjust the Good Octets received counters */ - carry_bit = 0x80000000 & stats->gorcl; - stats->gorcl += frame_len; - /* If the high bit of Gorcl (the low 32 bits of the Good Octets - * Received Count) was one before the addition, - * AND it is zero after, then we lost the carry out, - * need to add one to Gorch (Good Octets Received Count High). - * This could be simplified if all environments supported - * 64-bit integers. - */ - if (carry_bit && ((stats->gorcl & 0x80000000) == 0)) - stats->gorch++; - /* Is this a broadcast or multicast? Check broadcast first, - * since the test for a multicast frame will test positive on - * a broadcast frame. - */ - if ((mac_addr[0] == (uint8_t) 0xff) && (mac_addr[1] == (uint8_t) 0xff)) - /* Broadcast packet */ - stats->bprc++; - else if (*mac_addr & 0x01) - /* Multicast packet */ - stats->mprc++; - - if (frame_len == hw->max_frame_size) { - /* In this case, the hardware has overcounted the number of - * oversize frames. - */ - if (stats->roc > 0) - stats->roc--; - } - - /* Adjust the bin counters when the extra byte put the frame in the - * wrong bin. Remember that the frame_len was adjusted above. - */ - if (frame_len == 64) { - stats->prc64++; - stats->prc127--; - } else if (frame_len == 127) { - stats->prc127++; - stats->prc255--; - } else if (frame_len == 255) { - stats->prc255++; - stats->prc511--; - } else if (frame_len == 511) { - stats->prc511++; - stats->prc1023--; - } else if (frame_len == 1023) { - stats->prc1023++; - stats->prc1522--; - } else if (frame_len == 1522) { - stats->prc1522++; - } -} - -/****************************************************************************** - * Gets the current PCI bus type, speed, and width of the hardware - * - * hw - Struct containing variables accessed by shared code - *****************************************************************************/ -void -em_get_bus_info(struct em_hw *hw) -{ - int32_t ret_val; - uint16_t pci_ex_link_status; - uint32_t status; - - switch (hw->mac_type) { - case em_82542_rev2_0: - case em_82542_rev2_1: - hw->bus_type = em_bus_type_unknown; - hw->bus_speed = em_bus_speed_unknown; - hw->bus_width = em_bus_width_unknown; - break; - case em_82571: - case em_82572: - case em_82573: - case em_80003es2lan: - hw->bus_type = em_bus_type_pci_express; - hw->bus_speed = em_bus_speed_2500; - ret_val = em_read_pcie_cap_reg(hw, - PCI_EX_LINK_STATUS, - &pci_ex_link_status); - if (ret_val) - hw->bus_width = em_bus_width_unknown; - else - hw->bus_width = (pci_ex_link_status & PCI_EX_LINK_WIDTH_MASK) >> - PCI_EX_LINK_WIDTH_SHIFT; - break; - case em_ich8lan: - case em_ich9lan: - hw->bus_type = em_bus_type_pci_express; - hw->bus_speed = em_bus_speed_2500; - hw->bus_width = em_bus_width_pciex_1; - break; - default: - status = E1000_READ_REG(hw, STATUS); - hw->bus_type = (status & E1000_STATUS_PCIX_MODE) ? - em_bus_type_pcix : em_bus_type_pci; - - if (hw->device_id == E1000_DEV_ID_82546EB_QUAD_COPPER) { - hw->bus_speed = (hw->bus_type == em_bus_type_pci) ? - em_bus_speed_66 : em_bus_speed_120; - } else if (hw->bus_type == em_bus_type_pci) { - hw->bus_speed = (status & E1000_STATUS_PCI66) ? - em_bus_speed_66 : em_bus_speed_33; - } else { - switch (status & E1000_STATUS_PCIX_SPEED) { - case E1000_STATUS_PCIX_SPEED_66: - hw->bus_speed = em_bus_speed_66; - break; - case E1000_STATUS_PCIX_SPEED_100: - hw->bus_speed = em_bus_speed_100; - break; - case E1000_STATUS_PCIX_SPEED_133: - hw->bus_speed = em_bus_speed_133; - break; - default: - hw->bus_speed = em_bus_speed_reserved; - break; - } - } - hw->bus_width = (status & E1000_STATUS_BUS64) ? - em_bus_width_64 : em_bus_width_32; - break; - } -} - -/****************************************************************************** - * Writes a value to one of the devices registers using port I/O (as opposed to - * memory mapped I/O). Only 82544 and newer devices support port I/O. - * - * hw - Struct containing variables accessed by shared code - * offset - offset to write to - * value - value to write - *****************************************************************************/ -STATIC void -em_write_reg_io(struct em_hw *hw, - uint32_t offset, - uint32_t value) -{ - unsigned long io_addr = hw->io_base; - unsigned long io_data = hw->io_base + 4; - - em_io_write(hw, io_addr, offset); - em_io_write(hw, io_data, value); -} - -/****************************************************************************** - * Estimates the cable length. - * - * hw - Struct containing variables accessed by shared code - * min_length - The estimated minimum length - * max_length - The estimated maximum length - * - * returns: - E1000_ERR_XXX - * E1000_SUCCESS - * - * This function always returns a ranged length (minimum & maximum). - * So for M88 phy's, this function interprets the one value returned from the - * register to the minimum and maximum range. - * For IGP phy's, the function calculates the range by the AGC registers. - *****************************************************************************/ -STATIC int32_t -em_get_cable_length(struct em_hw *hw, - uint16_t *min_length, - uint16_t *max_length) -{ - int32_t ret_val; - uint16_t agc_value = 0; - uint16_t i, phy_data; - uint16_t cable_length; - - DEBUGFUNC("em_get_cable_length"); - - *min_length = *max_length = 0; - - /* Use old method for Phy older than IGP */ - if (hw->phy_type == em_phy_m88) { - - ret_val = em_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS, - &phy_data); - if (ret_val) - return ret_val; - cable_length = (phy_data & M88E1000_PSSR_CABLE_LENGTH) >> - M88E1000_PSSR_CABLE_LENGTH_SHIFT; - - /* Convert the enum value to ranged values */ - switch (cable_length) { - case em_cable_length_50: - *min_length = 0; - *max_length = em_igp_cable_length_50; - break; - case em_cable_length_50_80: - *min_length = em_igp_cable_length_50; - *max_length = em_igp_cable_length_80; - break; - case em_cable_length_80_110: - *min_length = em_igp_cable_length_80; - *max_length = em_igp_cable_length_110; - break; - case em_cable_length_110_140: - *min_length = em_igp_cable_length_110; - *max_length = em_igp_cable_length_140; - break; - case em_cable_length_140: - *min_length = em_igp_cable_length_140; - *max_length = em_igp_cable_length_170; - break; - default: - return -E1000_ERR_PHY; - break; - } - } else if (hw->phy_type == em_phy_gg82563) { - ret_val = em_read_phy_reg(hw, GG82563_PHY_DSP_DISTANCE, - &phy_data); - if (ret_val) - return ret_val; - cable_length = phy_data & GG82563_DSPD_CABLE_LENGTH; - - switch (cable_length) { - case em_gg_cable_length_60: - *min_length = 0; - *max_length = em_igp_cable_length_60; - break; - case em_gg_cable_length_60_115: - *min_length = em_igp_cable_length_60; - *max_length = em_igp_cable_length_115; - break; - case em_gg_cable_length_115_150: - *min_length = em_igp_cable_length_115; - *max_length = em_igp_cable_length_150; - break; - case em_gg_cable_length_150: - *min_length = em_igp_cable_length_150; - *max_length = em_igp_cable_length_180; - break; - default: - return -E1000_ERR_PHY; - break; - } - } else if (hw->phy_type == em_phy_igp) { /* For IGP PHY */ - uint16_t cur_agc_value; - uint16_t min_agc_value = IGP01E1000_AGC_LENGTH_TABLE_SIZE; - uint16_t agc_reg_array[IGP01E1000_PHY_CHANNEL_NUM] = - {IGP01E1000_PHY_AGC_A, - IGP01E1000_PHY_AGC_B, - IGP01E1000_PHY_AGC_C, - IGP01E1000_PHY_AGC_D}; - /* Read the AGC registers for all channels */ - for (i = 0; i < IGP01E1000_PHY_CHANNEL_NUM; i++) { - - ret_val = em_read_phy_reg(hw, agc_reg_array[i], &phy_data); - if (ret_val) - return ret_val; - - cur_agc_value = phy_data >> IGP01E1000_AGC_LENGTH_SHIFT; - - /* Value bound check. */ - if ((cur_agc_value >= IGP01E1000_AGC_LENGTH_TABLE_SIZE - 1) || - (cur_agc_value == 0)) - return -E1000_ERR_PHY; - - agc_value += cur_agc_value; - - /* Update minimal AGC value. */ - if (min_agc_value > cur_agc_value) - min_agc_value = cur_agc_value; - } - - /* Remove the minimal AGC result for length < 50m */ - if (agc_value < IGP01E1000_PHY_CHANNEL_NUM * em_igp_cable_length_50) { - agc_value -= min_agc_value; - - /* Get the average length of the remaining 3 channels */ - agc_value /= (IGP01E1000_PHY_CHANNEL_NUM - 1); - } else { - /* Get the average length of all the 4 channels. */ - agc_value /= IGP01E1000_PHY_CHANNEL_NUM; - } - - /* Set the range of the calculated length. */ - *min_length = ((em_igp_cable_length_table[agc_value] - - IGP01E1000_AGC_RANGE) > 0) ? - (em_igp_cable_length_table[agc_value] - - IGP01E1000_AGC_RANGE) : 0; - *max_length = em_igp_cable_length_table[agc_value] + - IGP01E1000_AGC_RANGE; - } else if (hw->phy_type == em_phy_igp_2 || - hw->phy_type == em_phy_igp_3) { - uint16_t cur_agc_index, max_agc_index = 0; - uint16_t min_agc_index = IGP02E1000_AGC_LENGTH_TABLE_SIZE - 1; - uint16_t agc_reg_array[IGP02E1000_PHY_CHANNEL_NUM] = - {IGP02E1000_PHY_AGC_A, - IGP02E1000_PHY_AGC_B, - IGP02E1000_PHY_AGC_C, - IGP02E1000_PHY_AGC_D}; - /* Read the AGC registers for all channels */ - for (i = 0; i < IGP02E1000_PHY_CHANNEL_NUM; i++) { - ret_val = em_read_phy_reg(hw, agc_reg_array[i], &phy_data); - if (ret_val) - return ret_val; - - /* Getting bits 15:9, which represent the combination of course and - * fine gain values. The result is a number that can be put into - * the lookup table to obtain the approximate cable length. */ - cur_agc_index = (phy_data >> IGP02E1000_AGC_LENGTH_SHIFT) & - IGP02E1000_AGC_LENGTH_MASK; - - /* Array index bound check. */ - if ((cur_agc_index >= IGP02E1000_AGC_LENGTH_TABLE_SIZE) || - (cur_agc_index == 0)) - return -E1000_ERR_PHY; - - /* Remove min & max AGC values from calculation. */ - if (em_igp_2_cable_length_table[min_agc_index] > - em_igp_2_cable_length_table[cur_agc_index]) - min_agc_index = cur_agc_index; - if (em_igp_2_cable_length_table[max_agc_index] < - em_igp_2_cable_length_table[cur_agc_index]) - max_agc_index = cur_agc_index; - - agc_value += em_igp_2_cable_length_table[cur_agc_index]; - } - - agc_value -= (em_igp_2_cable_length_table[min_agc_index] + - em_igp_2_cable_length_table[max_agc_index]); - agc_value /= (IGP02E1000_PHY_CHANNEL_NUM - 2); - - /* Calculate cable length with the error range of +/- 10 meters. */ - *min_length = ((agc_value - IGP02E1000_AGC_RANGE) > 0) ? - (agc_value - IGP02E1000_AGC_RANGE) : 0; - *max_length = agc_value + IGP02E1000_AGC_RANGE; - } - - return E1000_SUCCESS; -} - -/****************************************************************************** - * Check the cable polarity - * - * hw - Struct containing variables accessed by shared code - * polarity - output parameter : 0 - Polarity is not reversed - * 1 - Polarity is reversed. - * - * returns: - E1000_ERR_XXX - * E1000_SUCCESS - * - * For phy's older then IGP, this function simply reads the polarity bit in the - * Phy Status register. For IGP phy's, this bit is valid only if link speed is - * 10 Mbps. If the link speed is 100 Mbps there is no polarity so this bit will - * return 0. If the link speed is 1000 Mbps the polarity status is in the - * IGP01E1000_PHY_PCS_INIT_REG. - *****************************************************************************/ -STATIC int32_t -em_check_polarity(struct em_hw *hw, - em_rev_polarity *polarity) -{ - int32_t ret_val; - uint16_t phy_data; - - DEBUGFUNC("em_check_polarity"); - - if ((hw->phy_type == em_phy_m88) || - (hw->phy_type == em_phy_gg82563)) { - /* return the Polarity bit in the Status register. */ - ret_val = em_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS, - &phy_data); - if (ret_val) - return ret_val; - *polarity = ((phy_data & M88E1000_PSSR_REV_POLARITY) >> - M88E1000_PSSR_REV_POLARITY_SHIFT) ? - em_rev_polarity_reversed : em_rev_polarity_normal; - - } else if (hw->phy_type == em_phy_igp || - hw->phy_type == em_phy_igp_3 || - hw->phy_type == em_phy_igp_2) { - /* Read the Status register to check the speed */ - ret_val = em_read_phy_reg(hw, IGP01E1000_PHY_PORT_STATUS, - &phy_data); - if (ret_val) - return ret_val; - - /* If speed is 1000 Mbps, must read the IGP01E1000_PHY_PCS_INIT_REG to - * find the polarity status */ - if ((phy_data & IGP01E1000_PSSR_SPEED_MASK) == - IGP01E1000_PSSR_SPEED_1000MBPS) { - - /* Read the GIG initialization PCS register (0x00B4) */ - ret_val = em_read_phy_reg(hw, IGP01E1000_PHY_PCS_INIT_REG, - &phy_data); - if (ret_val) - return ret_val; - - /* Check the polarity bits */ - *polarity = (phy_data & IGP01E1000_PHY_POLARITY_MASK) ? - em_rev_polarity_reversed : em_rev_polarity_normal; - } else { - /* For 10 Mbps, read the polarity bit in the status register. (for - * 100 Mbps this bit is always 0) */ - *polarity = (phy_data & IGP01E1000_PSSR_POLARITY_REVERSED) ? - em_rev_polarity_reversed : em_rev_polarity_normal; - } - } else if (hw->phy_type == em_phy_ife) { - ret_val = em_read_phy_reg(hw, IFE_PHY_EXTENDED_STATUS_CONTROL, - &phy_data); - if (ret_val) - return ret_val; - *polarity = ((phy_data & IFE_PESC_POLARITY_REVERSED) >> - IFE_PESC_POLARITY_REVERSED_SHIFT) ? - em_rev_polarity_reversed : em_rev_polarity_normal; - } - return E1000_SUCCESS; -} - -/****************************************************************************** - * Check if Downshift occured - * - * hw - Struct containing variables accessed by shared code - * downshift - output parameter : 0 - No Downshift ocured. - * 1 - Downshift ocured. - * - * returns: - E1000_ERR_XXX - * E1000_SUCCESS - * - * For phy's older then IGP, this function reads the Downshift bit in the Phy - * Specific Status register. For IGP phy's, it reads the Downgrade bit in the - * Link Health register. In IGP this bit is latched high, so the driver must - * read it immediately after link is established. - *****************************************************************************/ -STATIC int32_t -em_check_downshift(struct em_hw *hw) -{ - int32_t ret_val; - uint16_t phy_data; - - DEBUGFUNC("em_check_downshift"); - - if (hw->phy_type == em_phy_igp || - hw->phy_type == em_phy_igp_3 || - hw->phy_type == em_phy_igp_2) { - ret_val = em_read_phy_reg(hw, IGP01E1000_PHY_LINK_HEALTH, - &phy_data); - if (ret_val) - return ret_val; - - hw->speed_downgraded = (phy_data & IGP01E1000_PLHR_SS_DOWNGRADE) ? 1 : 0; - } else if ((hw->phy_type == em_phy_m88) || - (hw->phy_type == em_phy_gg82563)) { - ret_val = em_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS, - &phy_data); - if (ret_val) - return ret_val; - - hw->speed_downgraded = (phy_data & M88E1000_PSSR_DOWNSHIFT) >> - M88E1000_PSSR_DOWNSHIFT_SHIFT; - } else if (hw->phy_type == em_phy_ife) { - /* em_phy_ife supports 10/100 speed only */ - hw->speed_downgraded = FALSE; - } - - return E1000_SUCCESS; -} - -/***************************************************************************** - * - * 82541_rev_2 & 82547_rev_2 have the capability to configure the DSP when a - * gigabit link is achieved to improve link quality. - * - * hw: Struct containing variables accessed by shared code - * - * returns: - E1000_ERR_PHY if fail to read/write the PHY - * E1000_SUCCESS at any other case. - * - ****************************************************************************/ - -STATIC int32_t -em_config_dsp_after_link_change(struct em_hw *hw, - boolean_t link_up) -{ - int32_t ret_val; - uint16_t phy_data, phy_saved_data, speed, duplex, i; - uint16_t dsp_reg_array[IGP01E1000_PHY_CHANNEL_NUM] = - {IGP01E1000_PHY_AGC_PARAM_A, - IGP01E1000_PHY_AGC_PARAM_B, - IGP01E1000_PHY_AGC_PARAM_C, - IGP01E1000_PHY_AGC_PARAM_D}; - uint16_t min_length, max_length; - - DEBUGFUNC("em_config_dsp_after_link_change"); - - if (hw->phy_type != em_phy_igp) - return E1000_SUCCESS; - - if (link_up) { - ret_val = em_get_speed_and_duplex(hw, &speed, &duplex); - if (ret_val) { - DEBUGOUT("Error getting link speed and duplex\n"); - return ret_val; - } - - if (speed == SPEED_1000) { - - ret_val = em_get_cable_length(hw, &min_length, &max_length); - if (ret_val) - return ret_val; - - if ((hw->dsp_config_state == em_dsp_config_enabled) && - min_length >= em_igp_cable_length_50) { - - for (i = 0; i < IGP01E1000_PHY_CHANNEL_NUM; i++) { - ret_val = em_read_phy_reg(hw, dsp_reg_array[i], - &phy_data); - if (ret_val) - return ret_val; - - phy_data &= ~IGP01E1000_PHY_EDAC_MU_INDEX; - - ret_val = em_write_phy_reg(hw, dsp_reg_array[i], - phy_data); - if (ret_val) - return ret_val; - } - hw->dsp_config_state = em_dsp_config_activated; - } - - if ((hw->ffe_config_state == em_ffe_config_enabled) && - (min_length < em_igp_cable_length_50)) { - - uint16_t ffe_idle_err_timeout = FFE_IDLE_ERR_COUNT_TIMEOUT_20; - uint32_t idle_errs = 0; - - /* clear previous idle error counts */ - ret_val = em_read_phy_reg(hw, PHY_1000T_STATUS, - &phy_data); - if (ret_val) - return ret_val; - - for (i = 0; i < ffe_idle_err_timeout; i++) { - usec_delay(1000); - ret_val = em_read_phy_reg(hw, PHY_1000T_STATUS, - &phy_data); - if (ret_val) - return ret_val; - - idle_errs += (phy_data & SR_1000T_IDLE_ERROR_CNT); - if (idle_errs > SR_1000T_PHY_EXCESSIVE_IDLE_ERR_COUNT) { - hw->ffe_config_state = em_ffe_config_active; - - ret_val = em_write_phy_reg(hw, - IGP01E1000_PHY_DSP_FFE, - IGP01E1000_PHY_DSP_FFE_CM_CP); - if (ret_val) - return ret_val; - break; - } - - if (idle_errs) - ffe_idle_err_timeout = FFE_IDLE_ERR_COUNT_TIMEOUT_100; - } - } - } - } else { - if (hw->dsp_config_state == em_dsp_config_activated) { - /* Save off the current value of register 0x2F5B to be restored at - * the end of the routines. */ - ret_val = em_read_phy_reg(hw, 0x2F5B, &phy_saved_data); - - if (ret_val) - return ret_val; - - /* Disable the PHY transmitter */ - ret_val = em_write_phy_reg(hw, 0x2F5B, 0x0003); - - if (ret_val) - return ret_val; - - msec_delay_irq(20); - - ret_val = em_write_phy_reg(hw, 0x0000, - IGP01E1000_IEEE_FORCE_GIGA); - if (ret_val) - return ret_val; - for (i = 0; i < IGP01E1000_PHY_CHANNEL_NUM; i++) { - ret_val = em_read_phy_reg(hw, dsp_reg_array[i], &phy_data); - if (ret_val) - return ret_val; - - phy_data &= ~IGP01E1000_PHY_EDAC_MU_INDEX; - phy_data |= IGP01E1000_PHY_EDAC_SIGN_EXT_9_BITS; - - ret_val = em_write_phy_reg(hw,dsp_reg_array[i], phy_data); - if (ret_val) - return ret_val; - } - - ret_val = em_write_phy_reg(hw, 0x0000, - IGP01E1000_IEEE_RESTART_AUTONEG); - if (ret_val) - return ret_val; - - msec_delay_irq(20); - - /* Now enable the transmitter */ - ret_val = em_write_phy_reg(hw, 0x2F5B, phy_saved_data); - - if (ret_val) - return ret_val; - - hw->dsp_config_state = em_dsp_config_enabled; - } - - if (hw->ffe_config_state == em_ffe_config_active) { - /* Save off the current value of register 0x2F5B to be restored at - * the end of the routines. */ - ret_val = em_read_phy_reg(hw, 0x2F5B, &phy_saved_data); - - if (ret_val) - return ret_val; - - /* Disable the PHY transmitter */ - ret_val = em_write_phy_reg(hw, 0x2F5B, 0x0003); - - if (ret_val) - return ret_val; - - msec_delay_irq(20); - - ret_val = em_write_phy_reg(hw, 0x0000, - IGP01E1000_IEEE_FORCE_GIGA); - if (ret_val) - return ret_val; - ret_val = em_write_phy_reg(hw, IGP01E1000_PHY_DSP_FFE, - IGP01E1000_PHY_DSP_FFE_DEFAULT); - if (ret_val) - return ret_val; - - ret_val = em_write_phy_reg(hw, 0x0000, - IGP01E1000_IEEE_RESTART_AUTONEG); - if (ret_val) - return ret_val; - - msec_delay_irq(20); - - /* Now enable the transmitter */ - ret_val = em_write_phy_reg(hw, 0x2F5B, phy_saved_data); - - if (ret_val) - return ret_val; - - hw->ffe_config_state = em_ffe_config_enabled; - } - } - return E1000_SUCCESS; -} - -/***************************************************************************** - * Set PHY to class A mode - * Assumes the following operations will follow to enable the new class mode. - * 1. Do a PHY soft reset - * 2. Restart auto-negotiation or force link. - * - * hw - Struct containing variables accessed by shared code - ****************************************************************************/ -static int32_t -em_set_phy_mode(struct em_hw *hw) -{ - int32_t ret_val; - uint16_t eeprom_data; - - DEBUGFUNC("em_set_phy_mode"); - - if ((hw->mac_type == em_82545_rev_3) && - (hw->media_type == em_media_type_copper)) { - ret_val = em_read_eeprom(hw, EEPROM_PHY_CLASS_WORD, 1, &eeprom_data); - if (ret_val) { - return ret_val; - } - - if ((eeprom_data != EEPROM_RESERVED_WORD) && - (eeprom_data & EEPROM_PHY_CLASS_A)) { - ret_val = em_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x000B); - if (ret_val) - return ret_val; - ret_val = em_write_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, 0x8104); - if (ret_val) - return ret_val; - - hw->phy_reset_disable = FALSE; - } - } - - return E1000_SUCCESS; -} - -/***************************************************************************** - * - * This function sets the lplu state according to the active flag. When - * activating lplu this function also disables smart speed and vise versa. - * lplu will not be activated unless the device autonegotiation advertisment - * meets standards of either 10 or 10/100 or 10/100/1000 at all duplexes. - * hw: Struct containing variables accessed by shared code - * active - true to enable lplu false to disable lplu. - * - * returns: - E1000_ERR_PHY if fail to read/write the PHY - * E1000_SUCCESS at any other case. - * - ****************************************************************************/ - -STATIC int32_t -em_set_d3_lplu_state(struct em_hw *hw, - boolean_t active) -{ - uint32_t phy_ctrl = 0; - int32_t ret_val; - uint16_t phy_data; - DEBUGFUNC("em_set_d3_lplu_state"); - - if (hw->phy_type != em_phy_igp && hw->phy_type != em_phy_igp_2 - && hw->phy_type != em_phy_igp_3) - return E1000_SUCCESS; - - /* During driver activity LPLU should not be used or it will attain link - * from the lowest speeds starting from 10Mbps. The capability is used for - * Dx transitions and states */ - if (hw->mac_type == em_82541_rev_2 || hw->mac_type == em_82547_rev_2) { - ret_val = em_read_phy_reg(hw, IGP01E1000_GMII_FIFO, &phy_data); - if (ret_val) - return ret_val; - } else if (hw->mac_type == em_ich8lan || hw->mac_type == em_ich9lan) { - /* MAC writes into PHY register based on the state transition - * and start auto-negotiation. SW driver can overwrite the settings - * in CSR PHY power control E1000_PHY_CTRL register. */ - phy_ctrl = E1000_READ_REG(hw, PHY_CTRL); - } else { - ret_val = em_read_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT, &phy_data); - if (ret_val) - return ret_val; - } - - if (!active) { - if (hw->mac_type == em_82541_rev_2 || - hw->mac_type == em_82547_rev_2) { - phy_data &= ~IGP01E1000_GMII_FLEX_SPD; - ret_val = em_write_phy_reg(hw, IGP01E1000_GMII_FIFO, phy_data); - if (ret_val) - return ret_val; - } else { - if (hw->mac_type == em_ich8lan || hw->mac_type == em_ich9lan) { - phy_ctrl &= ~E1000_PHY_CTRL_NOND0A_LPLU; - E1000_WRITE_REG(hw, PHY_CTRL, phy_ctrl); - } else { - phy_data &= ~IGP02E1000_PM_D3_LPLU; - ret_val = em_write_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT, - phy_data); - if (ret_val) - return ret_val; - } - } - - /* LPLU and SmartSpeed are mutually exclusive. LPLU is used during - * Dx states where the power conservation is most important. During - * driver activity we should enable SmartSpeed, so performance is - * maintained. */ - if (hw->smart_speed == em_smart_speed_on) { - ret_val = em_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, - &phy_data); - if (ret_val) - return ret_val; - - phy_data |= IGP01E1000_PSCFR_SMART_SPEED; - ret_val = em_write_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, - phy_data); - if (ret_val) - return ret_val; - } else if (hw->smart_speed == em_smart_speed_off) { - ret_val = em_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, - &phy_data); - if (ret_val) - return ret_val; - - phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED; - ret_val = em_write_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, - phy_data); - if (ret_val) - return ret_val; - } - - } else if ((hw->autoneg_advertised == AUTONEG_ADVERTISE_SPEED_DEFAULT) || - (hw->autoneg_advertised == AUTONEG_ADVERTISE_10_ALL ) || - (hw->autoneg_advertised == AUTONEG_ADVERTISE_10_100_ALL)) { - - if (hw->mac_type == em_82541_rev_2 || - hw->mac_type == em_82547_rev_2) { - phy_data |= IGP01E1000_GMII_FLEX_SPD; - ret_val = em_write_phy_reg(hw, IGP01E1000_GMII_FIFO, phy_data); - if (ret_val) - return ret_val; - } else { - if (hw->mac_type == em_ich8lan || hw->mac_type == em_ich9lan) { - phy_ctrl |= E1000_PHY_CTRL_NOND0A_LPLU; - E1000_WRITE_REG(hw, PHY_CTRL, phy_ctrl); - } else { - phy_data |= IGP02E1000_PM_D3_LPLU; - ret_val = em_write_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT, - phy_data); - if (ret_val) - return ret_val; - } - } - - /* When LPLU is enabled we should disable SmartSpeed */ - ret_val = em_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, &phy_data); - if (ret_val) - return ret_val; - - phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED; - ret_val = em_write_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, phy_data); - if (ret_val) - return ret_val; - - } - return E1000_SUCCESS; -} - -/***************************************************************************** - * - * This function sets the lplu d0 state according to the active flag. When - * activating lplu this function also disables smart speed and vise versa. - * lplu will not be activated unless the device autonegotiation advertisment - * meets standards of either 10 or 10/100 or 10/100/1000 at all duplexes. - * hw: Struct containing variables accessed by shared code - * active - true to enable lplu false to disable lplu. - * - * returns: - E1000_ERR_PHY if fail to read/write the PHY - * E1000_SUCCESS at any other case. - * - ****************************************************************************/ - -STATIC int32_t -em_set_d0_lplu_state(struct em_hw *hw, - boolean_t active) -{ - uint32_t phy_ctrl = 0; - int32_t ret_val; - uint16_t phy_data; - DEBUGFUNC("em_set_d0_lplu_state"); - - if (hw->mac_type <= em_82547_rev_2) - return E1000_SUCCESS; - - if (hw->mac_type == em_ich8lan || hw->mac_type == em_ich9lan) { - phy_ctrl = E1000_READ_REG(hw, PHY_CTRL); - } else { - ret_val = em_read_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT, &phy_data); - if (ret_val) - return ret_val; - } - - if (!active) { - if (hw->mac_type == em_ich8lan || hw->mac_type == em_ich9lan) { - phy_ctrl &= ~E1000_PHY_CTRL_D0A_LPLU; - E1000_WRITE_REG(hw, PHY_CTRL, phy_ctrl); - } else { - phy_data &= ~IGP02E1000_PM_D0_LPLU; - ret_val = em_write_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT, phy_data); - if (ret_val) - return ret_val; - } - - /* LPLU and SmartSpeed are mutually exclusive. LPLU is used during - * Dx states where the power conservation is most important. During - * driver activity we should enable SmartSpeed, so performance is - * maintained. */ - if (hw->smart_speed == em_smart_speed_on) { - ret_val = em_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, - &phy_data); - if (ret_val) - return ret_val; - - phy_data |= IGP01E1000_PSCFR_SMART_SPEED; - ret_val = em_write_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, - phy_data); - if (ret_val) - return ret_val; - } else if (hw->smart_speed == em_smart_speed_off) { - ret_val = em_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, - &phy_data); - if (ret_val) - return ret_val; - - phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED; - ret_val = em_write_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, - phy_data); - if (ret_val) - return ret_val; - } - - - } else { - - if (hw->mac_type == em_ich8lan || hw->mac_type == em_ich9lan) { - phy_ctrl |= E1000_PHY_CTRL_D0A_LPLU; - E1000_WRITE_REG(hw, PHY_CTRL, phy_ctrl); - } else { - phy_data |= IGP02E1000_PM_D0_LPLU; - ret_val = em_write_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT, phy_data); - if (ret_val) - return ret_val; - } - - /* When LPLU is enabled we should disable SmartSpeed */ - ret_val = em_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, &phy_data); - if (ret_val) - return ret_val; - - phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED; - ret_val = em_write_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, phy_data); - if (ret_val) - return ret_val; - - } - return E1000_SUCCESS; -} - -/****************************************************************************** - * Change VCO speed register to improve Bit Error Rate performance of SERDES. - * - * hw - Struct containing variables accessed by shared code - *****************************************************************************/ -static int32_t -em_set_vco_speed(struct em_hw *hw) -{ - int32_t ret_val; - uint16_t default_page = 0; - uint16_t phy_data; - - DEBUGFUNC("em_set_vco_speed"); - - switch (hw->mac_type) { - case em_82545_rev_3: - case em_82546_rev_3: - break; - default: - return E1000_SUCCESS; - } - - /* Set PHY register 30, page 5, bit 8 to 0 */ - - ret_val = em_read_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, &default_page); - if (ret_val) - return ret_val; - - ret_val = em_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x0005); - if (ret_val) - return ret_val; - - ret_val = em_read_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, &phy_data); - if (ret_val) - return ret_val; - - phy_data &= ~M88E1000_PHY_VCO_REG_BIT8; - ret_val = em_write_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, phy_data); - if (ret_val) - return ret_val; - - /* Set PHY register 30, page 4, bit 11 to 1 */ - - ret_val = em_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x0004); - if (ret_val) - return ret_val; - - ret_val = em_read_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, &phy_data); - if (ret_val) - return ret_val; - - phy_data |= M88E1000_PHY_VCO_REG_BIT11; - ret_val = em_write_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, phy_data); - if (ret_val) - return ret_val; - - ret_val = em_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, default_page); - if (ret_val) - return ret_val; - - return E1000_SUCCESS; -} - - -/***************************************************************************** - * This function reads the cookie from ARC ram. - * - * returns: - E1000_SUCCESS . - ****************************************************************************/ -STATIC int32_t -em_host_if_read_cookie(struct em_hw * hw, uint8_t *buffer) -{ - uint8_t i; - uint32_t offset = E1000_MNG_DHCP_COOKIE_OFFSET; - uint8_t length = E1000_MNG_DHCP_COOKIE_LENGTH; - - length = (length >> 2); - offset = (offset >> 2); - - for (i = 0; i < length; i++) { - *((uint32_t *) buffer + i) = - E1000_READ_REG_ARRAY_DWORD(hw, HOST_IF, offset + i); - } - return E1000_SUCCESS; -} - - -/***************************************************************************** - * This function checks whether the HOST IF is enabled for command operaton - * and also checks whether the previous command is completed. - * It busy waits in case of previous command is not completed. - * - * returns: - E1000_ERR_HOST_INTERFACE_COMMAND in case if is not ready or - * timeout - * - E1000_SUCCESS for success. - ****************************************************************************/ -STATIC int32_t -em_mng_enable_host_if(struct em_hw * hw) -{ - uint32_t hicr; - uint8_t i; - - /* Check that the host interface is enabled. */ - hicr = E1000_READ_REG(hw, HICR); - if ((hicr & E1000_HICR_EN) == 0) { - DEBUGOUT("E1000_HOST_EN bit disabled.\n"); - return -E1000_ERR_HOST_INTERFACE_COMMAND; - } - /* check the previous command is completed */ - for (i = 0; i < E1000_MNG_DHCP_COMMAND_TIMEOUT; i++) { - hicr = E1000_READ_REG(hw, HICR); - if (!(hicr & E1000_HICR_C)) - break; - msec_delay_irq(1); - } - - if (i == E1000_MNG_DHCP_COMMAND_TIMEOUT) { - DEBUGOUT("Previous command timeout failed .\n"); - return -E1000_ERR_HOST_INTERFACE_COMMAND; - } - return E1000_SUCCESS; -} - -/***************************************************************************** - * This function writes the buffer content at the offset given on the host if. - * It also does alignment considerations to do the writes in most efficient way. - * Also fills up the sum of the buffer in *buffer parameter. - * - * returns - E1000_SUCCESS for success. - ****************************************************************************/ -STATIC int32_t -em_mng_host_if_write(struct em_hw * hw, uint8_t *buffer, - uint16_t length, uint16_t offset, uint8_t *sum) -{ - uint8_t *tmp; - uint8_t *bufptr = buffer; - uint32_t data = 0; - uint16_t remaining, i, j, prev_bytes; - - /* sum = only sum of the data and it is not checksum */ - - if (length == 0 || offset + length > E1000_HI_MAX_MNG_DATA_LENGTH) { - return -E1000_ERR_PARAM; - } - - tmp = (uint8_t *)&data; - prev_bytes = offset & 0x3; - offset &= 0xFFFC; - offset >>= 2; - - if (prev_bytes) { - data = E1000_READ_REG_ARRAY_DWORD(hw, HOST_IF, offset); - for (j = prev_bytes; j < sizeof(uint32_t); j++) { - *(tmp + j) = *bufptr++; - *sum += *(tmp + j); - } - E1000_WRITE_REG_ARRAY_DWORD(hw, HOST_IF, offset, data); - length -= j - prev_bytes; - offset++; - } - - remaining = length & 0x3; - length -= remaining; - - /* Calculate length in DWORDs */ - length >>= 2; - - /* The device driver writes the relevant command block into the - * ram area. */ - for (i = 0; i < length; i++) { - for (j = 0; j < sizeof(uint32_t); j++) { - *(tmp + j) = *bufptr++; - *sum += *(tmp + j); - } - - E1000_WRITE_REG_ARRAY_DWORD(hw, HOST_IF, offset + i, data); - } - if (remaining) { - for (j = 0; j < sizeof(uint32_t); j++) { - if (j < remaining) - *(tmp + j) = *bufptr++; - else - *(tmp + j) = 0; - - *sum += *(tmp + j); - } - E1000_WRITE_REG_ARRAY_DWORD(hw, HOST_IF, offset + i, data); - } - - return E1000_SUCCESS; -} - - -/***************************************************************************** - * This function writes the command header after does the checksum calculation. - * - * returns - E1000_SUCCESS for success. - ****************************************************************************/ -STATIC int32_t -em_mng_write_cmd_header(struct em_hw * hw, - struct em_host_mng_command_header * hdr) -{ - uint16_t i; - uint8_t sum; - uint8_t *buffer; - - /* Write the whole command header structure which includes sum of - * the buffer */ - - uint16_t length = sizeof(struct em_host_mng_command_header); - - sum = hdr->checksum; - hdr->checksum = 0; - - buffer = (uint8_t *) hdr; - i = length; - while (i--) - sum += buffer[i]; - - hdr->checksum = 0 - sum; - - length >>= 2; - /* The device driver writes the relevant command block into the ram area. */ - for (i = 0; i < length; i++) { - E1000_WRITE_REG_ARRAY_DWORD(hw, HOST_IF, i, *((uint32_t *) hdr + i)); - E1000_WRITE_FLUSH(hw); - } - - return E1000_SUCCESS; -} - - -/***************************************************************************** - * This function indicates to ARC that a new command is pending which completes - * one write operation by the driver. - * - * returns - E1000_SUCCESS for success. - ****************************************************************************/ -STATIC int32_t -em_mng_write_commit(struct em_hw * hw) -{ - uint32_t hicr; - - hicr = E1000_READ_REG(hw, HICR); - /* Setting this bit tells the ARC that a new command is pending. */ - E1000_WRITE_REG(hw, HICR, hicr | E1000_HICR_C); - - return E1000_SUCCESS; -} - - -/***************************************************************************** - * This function checks the mode of the firmware. - * - * returns - TRUE when the mode is IAMT or FALSE. - ****************************************************************************/ -boolean_t -em_check_mng_mode(struct em_hw *hw) -{ - uint32_t fwsm; - - fwsm = E1000_READ_REG(hw, FWSM); - - if (hw->mac_type == em_ich8lan || hw->mac_type == em_ich8lan) { - if ((fwsm & E1000_FWSM_MODE_MASK) == - (E1000_MNG_ICH_IAMT_MODE << E1000_FWSM_MODE_SHIFT)) - return TRUE; - } else if ((fwsm & E1000_FWSM_MODE_MASK) == - (E1000_MNG_IAMT_MODE << E1000_FWSM_MODE_SHIFT)) - return TRUE; - - return FALSE; -} - - -/***************************************************************************** - * This function writes the dhcp info . - ****************************************************************************/ -int32_t -em_mng_write_dhcp_info(struct em_hw * hw, uint8_t *buffer, - uint16_t length) -{ - int32_t ret_val; - struct em_host_mng_command_header hdr; - - hdr.command_id = E1000_MNG_DHCP_TX_PAYLOAD_CMD; - hdr.command_length = length; - hdr.reserved1 = 0; - hdr.reserved2 = 0; - hdr.checksum = 0; - - ret_val = em_mng_enable_host_if(hw); - if (ret_val == E1000_SUCCESS) { - ret_val = em_mng_host_if_write(hw, buffer, length, sizeof(hdr), - &(hdr.checksum)); - if (ret_val == E1000_SUCCESS) { - ret_val = em_mng_write_cmd_header(hw, &hdr); - if (ret_val == E1000_SUCCESS) - ret_val = em_mng_write_commit(hw); - } - } - return ret_val; -} - - -/***************************************************************************** - * This function calculates the checksum. - * - * returns - checksum of buffer contents. - ****************************************************************************/ -STATIC uint8_t -em_calculate_mng_checksum(char *buffer, uint32_t length) -{ - uint8_t sum = 0; - uint32_t i; - - if (!buffer) - return 0; - - for (i=0; i < length; i++) - sum += buffer[i]; - - return (uint8_t) (0 - sum); -} - -/***************************************************************************** - * This function checks whether tx pkt filtering needs to be enabled or not. - * - * returns - TRUE for packet filtering or FALSE. - ****************************************************************************/ -boolean_t -em_enable_tx_pkt_filtering(struct em_hw *hw) -{ - /* called in init as well as watchdog timer functions */ - - int32_t ret_val, checksum; - boolean_t tx_filter = FALSE; - struct em_host_mng_dhcp_cookie *hdr = &(hw->mng_cookie); - uint8_t *buffer = (uint8_t *) &(hw->mng_cookie); - - if (em_check_mng_mode(hw)) { - ret_val = em_mng_enable_host_if(hw); - if (ret_val == E1000_SUCCESS) { - ret_val = em_host_if_read_cookie(hw, buffer); - if (ret_val == E1000_SUCCESS) { - checksum = hdr->checksum; - hdr->checksum = 0; - if ((hdr->signature == E1000_IAMT_SIGNATURE) && - checksum == em_calculate_mng_checksum((char *)buffer, - E1000_MNG_DHCP_COOKIE_LENGTH)) { - if (hdr->status & - E1000_MNG_DHCP_COOKIE_STATUS_PARSING_SUPPORT) - tx_filter = TRUE; - } else - tx_filter = TRUE; - } else - tx_filter = TRUE; - } - } - - hw->tx_pkt_filtering = tx_filter; - return tx_filter; -} - -/****************************************************************************** - * Verifies the hardware needs to allow ARPs to be processed by the host - * - * hw - Struct containing variables accessed by shared code - * - * returns: - TRUE/FALSE - * - *****************************************************************************/ -uint32_t -em_enable_mng_pass_thru(struct em_hw *hw) -{ - uint32_t manc; - uint32_t fwsm, factps; - - if (hw->asf_firmware_present) { - manc = E1000_READ_REG(hw, MANC); - - if (!(manc & E1000_MANC_RCV_TCO_EN) || - !(manc & E1000_MANC_EN_MAC_ADDR_FILTER)) - return FALSE; - if (em_arc_subsystem_valid(hw) == TRUE) { - fwsm = E1000_READ_REG(hw, FWSM); - factps = E1000_READ_REG(hw, FACTPS); - - if (((fwsm & E1000_FWSM_MODE_MASK) == - (em_mng_mode_pt << E1000_FWSM_MODE_SHIFT)) && - (factps & E1000_FACTPS_MNGCG)) - return TRUE; - } else - if ((manc & E1000_MANC_SMBUS_EN) && !(manc & E1000_MANC_ASF_EN)) - return TRUE; - } - return FALSE; -} - -static int32_t -em_polarity_reversal_workaround(struct em_hw *hw) -{ - int32_t ret_val; - uint16_t mii_status_reg; - uint16_t i; - - /* Polarity reversal workaround for forced 10F/10H links. */ - - /* Disable the transmitter on the PHY */ - - ret_val = em_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x0019); - if (ret_val) - return ret_val; - ret_val = em_write_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, 0xFFFF); - if (ret_val) - return ret_val; - - ret_val = em_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x0000); - if (ret_val) - return ret_val; - - /* This loop will early-out if the NO link condition has been met. */ - for (i = PHY_FORCE_TIME; i > 0; i--) { - /* Read the MII Status Register and wait for Link Status bit - * to be clear. - */ - - ret_val = em_read_phy_reg(hw, PHY_STATUS, &mii_status_reg); - if (ret_val) - return ret_val; - - ret_val = em_read_phy_reg(hw, PHY_STATUS, &mii_status_reg); - if (ret_val) - return ret_val; - - if ((mii_status_reg & ~MII_SR_LINK_STATUS) == 0) break; - msec_delay_irq(100); - } - - /* Recommended delay time after link has been lost */ - msec_delay_irq(1000); - - /* Now we will re-enable th transmitter on the PHY */ - - ret_val = em_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x0019); - if (ret_val) - return ret_val; - msec_delay_irq(50); - ret_val = em_write_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, 0xFFF0); - if (ret_val) - return ret_val; - msec_delay_irq(50); - ret_val = em_write_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, 0xFF00); - if (ret_val) - return ret_val; - msec_delay_irq(50); - ret_val = em_write_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, 0x0000); - if (ret_val) - return ret_val; - - ret_val = em_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x0000); - if (ret_val) - return ret_val; - - /* This loop will early-out if the link condition has been met. */ - for (i = PHY_FORCE_TIME; i > 0; i--) { - /* Read the MII Status Register and wait for Link Status bit - * to be set. - */ - - ret_val = em_read_phy_reg(hw, PHY_STATUS, &mii_status_reg); - if (ret_val) - return ret_val; - - ret_val = em_read_phy_reg(hw, PHY_STATUS, &mii_status_reg); - if (ret_val) - return ret_val; - - if (mii_status_reg & MII_SR_LINK_STATUS) break; - msec_delay_irq(100); - } - return E1000_SUCCESS; -} - -/*************************************************************************** - * - * Disables PCI-Express master access. - * - * hw: Struct containing variables accessed by shared code - * - * returns: - none. - * - ***************************************************************************/ -STATIC void -em_set_pci_express_master_disable(struct em_hw *hw) -{ - uint32_t ctrl; - - DEBUGFUNC("em_set_pci_express_master_disable"); - - if (hw->bus_type != em_bus_type_pci_express) - return; - - ctrl = E1000_READ_REG(hw, CTRL); - ctrl |= E1000_CTRL_GIO_MASTER_DISABLE; - E1000_WRITE_REG(hw, CTRL, ctrl); -} - -/******************************************************************************* - * - * Disables PCI-Express master access and verifies there are no pending requests - * - * hw: Struct containing variables accessed by shared code - * - * returns: - E1000_ERR_MASTER_REQUESTS_PENDING if master disable bit hasn't - * caused the master requests to be disabled. - * E1000_SUCCESS master requests disabled. - * - ******************************************************************************/ -int32_t -em_disable_pciex_master(struct em_hw *hw) -{ - int32_t timeout = MASTER_DISABLE_TIMEOUT; /* 80ms */ - - DEBUGFUNC("em_disable_pciex_master"); - - if (hw->bus_type != em_bus_type_pci_express) - return E1000_SUCCESS; - - em_set_pci_express_master_disable(hw); - - while (timeout) { - if (!(E1000_READ_REG(hw, STATUS) & E1000_STATUS_GIO_MASTER_ENABLE)) - break; - else - usec_delay(100); - timeout--; - } - - if (!timeout) { - DEBUGOUT("Master requests are pending.\n"); - return -E1000_ERR_MASTER_REQUESTS_PENDING; - } - - return E1000_SUCCESS; -} - -/******************************************************************************* - * - * Check for EEPROM Auto Read bit done. - * - * hw: Struct containing variables accessed by shared code - * - * returns: - E1000_ERR_RESET if fail to reset MAC - * E1000_SUCCESS at any other case. - * - ******************************************************************************/ -STATIC int32_t -em_get_auto_rd_done(struct em_hw *hw) -{ - int32_t timeout = AUTO_READ_DONE_TIMEOUT; - - DEBUGFUNC("em_get_auto_rd_done"); - - switch (hw->mac_type) { - default: - msec_delay(5); - break; - case em_82571: - case em_82572: - case em_82573: - case em_80003es2lan: - case em_ich9lan: - case em_ich8lan: - while (timeout) { - if (E1000_READ_REG(hw, EECD) & E1000_EECD_AUTO_RD) - break; - else msec_delay(1); - timeout--; - } - - if (!timeout) { - DEBUGOUT("Auto read by HW from EEPROM has not completed.\n"); - return -E1000_ERR_RESET; - } - break; - } - - /* PHY configuration from NVM just starts after EECD_AUTO_RD sets to high. - * Need to wait for PHY configuration completion before accessing NVM - * and PHY. */ - if (hw->mac_type == em_82573) - msec_delay(25); - - return E1000_SUCCESS; -} - -/*************************************************************************** - * Checks if the PHY configuration is done - * - * hw: Struct containing variables accessed by shared code - * - * returns: - E1000_ERR_RESET if fail to reset MAC - * E1000_SUCCESS at any other case. - * - ***************************************************************************/ -STATIC int32_t -em_get_phy_cfg_done(struct em_hw *hw) -{ - int32_t timeout = PHY_CFG_TIMEOUT; - uint32_t cfg_mask = E1000_EEPROM_CFG_DONE; - - DEBUGFUNC("em_get_phy_cfg_done"); - - switch (hw->mac_type) { - default: - msec_delay_irq(10); - break; - case em_80003es2lan: - /* Separate *_CFG_DONE_* bit for each port */ - if (E1000_READ_REG(hw, STATUS) & E1000_STATUS_FUNC_1) - cfg_mask = E1000_EEPROM_CFG_DONE_PORT_1; - /* Fall Through */ - case em_82571: - case em_82572: - while (timeout) { - if (E1000_READ_REG(hw, EEMNGCTL) & cfg_mask) - break; - else - msec_delay(1); - timeout--; - } - if (!timeout) { - DEBUGOUT("MNG configuration cycle has not completed.\n"); - return -E1000_ERR_RESET; - } - break; - } - - return E1000_SUCCESS; -} - -/*************************************************************************** - * - * Using the combination of SMBI and SWESMBI semaphore bits when resetting - * adapter or Eeprom access. - * - * hw: Struct containing variables accessed by shared code - * - * returns: - E1000_ERR_EEPROM if fail to access EEPROM. - * E1000_SUCCESS at any other case. - * - ***************************************************************************/ -STATIC int32_t -em_get_hw_eeprom_semaphore(struct em_hw *hw) -{ - int32_t timeout; - uint32_t swsm; - - DEBUGFUNC("em_get_hw_eeprom_semaphore"); - - if (!hw->eeprom_semaphore_present) - return E1000_SUCCESS; - - if (hw->mac_type == em_80003es2lan) { - /* Get the SW semaphore. */ - if (em_get_software_semaphore(hw) != E1000_SUCCESS) - return -E1000_ERR_EEPROM; - } - - /* Get the FW semaphore. */ - timeout = hw->eeprom.word_size + 1; - while (timeout) { - swsm = E1000_READ_REG(hw, SWSM); - swsm |= E1000_SWSM_SWESMBI; - E1000_WRITE_REG(hw, SWSM, swsm); - /* if we managed to set the bit we got the semaphore. */ - swsm = E1000_READ_REG(hw, SWSM); - if (swsm & E1000_SWSM_SWESMBI) - break; - - usec_delay(50); - timeout--; - } - - if (!timeout) { - /* Release semaphores */ - em_put_hw_eeprom_semaphore(hw); - DEBUGOUT("Driver can't access the Eeprom - SWESMBI bit is set.\n"); - return -E1000_ERR_EEPROM; - } - - return E1000_SUCCESS; -} - -/*************************************************************************** - * This function clears HW semaphore bits. - * - * hw: Struct containing variables accessed by shared code - * - * returns: - None. - * - ***************************************************************************/ -STATIC void -em_put_hw_eeprom_semaphore(struct em_hw *hw) -{ - uint32_t swsm; - - DEBUGFUNC("em_put_hw_eeprom_semaphore"); - - if (!hw->eeprom_semaphore_present) - return; - - swsm = E1000_READ_REG(hw, SWSM); - if (hw->mac_type == em_80003es2lan) { - /* Release both semaphores. */ - swsm &= ~(E1000_SWSM_SMBI | E1000_SWSM_SWESMBI); - } else - swsm &= ~(E1000_SWSM_SWESMBI); - E1000_WRITE_REG(hw, SWSM, swsm); -} - -/*************************************************************************** - * - * Obtaining software semaphore bit (SMBI) before resetting PHY. - * - * hw: Struct containing variables accessed by shared code - * - * returns: - E1000_ERR_RESET if fail to obtain semaphore. - * E1000_SUCCESS at any other case. - * - ***************************************************************************/ -STATIC int32_t -em_get_software_semaphore(struct em_hw *hw) -{ - int32_t timeout = hw->eeprom.word_size + 1; - uint32_t swsm; - - DEBUGFUNC("em_get_software_semaphore"); - - if (hw->mac_type != em_80003es2lan) { - return E1000_SUCCESS; - } - - while (timeout) { - swsm = E1000_READ_REG(hw, SWSM); - /* If SMBI bit cleared, it is now set and we hold the semaphore */ - if (!(swsm & E1000_SWSM_SMBI)) - break; - msec_delay_irq(1); - timeout--; - } - - if (!timeout) { - DEBUGOUT("Driver can't access device - SMBI bit is set.\n"); - return -E1000_ERR_RESET; - } - - return E1000_SUCCESS; -} - -/*************************************************************************** - * - * Release semaphore bit (SMBI). - * - * hw: Struct containing variables accessed by shared code - * - ***************************************************************************/ -STATIC void -em_release_software_semaphore(struct em_hw *hw) -{ - uint32_t swsm; - - DEBUGFUNC("em_release_software_semaphore"); - - if (hw->mac_type != em_80003es2lan) { - return; - } - - swsm = E1000_READ_REG(hw, SWSM); - /* Release the SW semaphores.*/ - swsm &= ~E1000_SWSM_SMBI; - E1000_WRITE_REG(hw, SWSM, swsm); -} - -/****************************************************************************** - * Checks if PHY reset is blocked due to SOL/IDER session, for example. - * Returning E1000_BLK_PHY_RESET isn't necessarily an error. But it's up to - * the caller to figure out how to deal with it. - * - * hw - Struct containing variables accessed by shared code - * - * returns: - E1000_BLK_PHY_RESET - * E1000_SUCCESS - * - *****************************************************************************/ -int32_t -em_check_phy_reset_block(struct em_hw *hw) -{ - uint32_t manc = 0; - uint32_t fwsm = 0; - - if (hw->mac_type == em_ich8lan || hw->mac_type == em_ich9lan) { - fwsm = E1000_READ_REG(hw, FWSM); - return (fwsm & E1000_FWSM_RSPCIPHY) ? E1000_SUCCESS - : E1000_BLK_PHY_RESET; - } - - if (hw->mac_type > em_82547_rev_2) - manc = E1000_READ_REG(hw, MANC); - return (manc & E1000_MANC_BLK_PHY_RST_ON_IDE) ? - E1000_BLK_PHY_RESET : E1000_SUCCESS; -} - -STATIC uint8_t -em_arc_subsystem_valid(struct em_hw *hw) -{ - uint32_t fwsm; - - /* On 8257x silicon, registers in the range of 0x8800 - 0x8FFC - * may not be provided a DMA clock when no manageability features are - * enabled. We do not want to perform any reads/writes to these registers - * if this is the case. We read FWSM to determine the manageability mode. - */ - switch (hw->mac_type) { - case em_82571: - case em_82572: - case em_82573: - case em_80003es2lan: - fwsm = E1000_READ_REG(hw, FWSM); - if ((fwsm & E1000_FWSM_MODE_MASK) != 0) - return TRUE; - break; - case em_ich8lan: - case em_ich9lan: - return TRUE; - default: - break; - } - return FALSE; -} - - -/****************************************************************************** - * Configure PCI-Ex no-snoop - * - * hw - Struct containing variables accessed by shared code. - * no_snoop - Bitmap of no-snoop events. - * - * returns: E1000_SUCCESS - * - *****************************************************************************/ -STATIC int32_t -em_set_pci_ex_no_snoop(struct em_hw *hw, uint32_t no_snoop) -{ - uint32_t gcr_reg = 0; - - DEBUGFUNC("em_set_pci_ex_no_snoop"); - - if (hw->bus_type == em_bus_type_unknown) - em_get_bus_info(hw); - - if (hw->bus_type != em_bus_type_pci_express) - return E1000_SUCCESS; - - if (no_snoop) { - gcr_reg = E1000_READ_REG(hw, GCR); - gcr_reg &= ~(PCI_EX_NO_SNOOP_ALL); - gcr_reg |= no_snoop; - E1000_WRITE_REG(hw, GCR, gcr_reg); - } - if (hw->mac_type == em_ich8lan) { - uint32_t ctrl_ext; - - E1000_WRITE_REG(hw, GCR, PCI_EX_82566_SNOOP_ALL); - - ctrl_ext = E1000_READ_REG(hw, CTRL_EXT); - ctrl_ext |= E1000_CTRL_EXT_RO_DIS; - E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext); - } - - return E1000_SUCCESS; -} - -/*************************************************************************** - * - * Get software semaphore FLAG bit (SWFLAG). - * SWFLAG is used to synchronize the access to all shared resource between - * SW, FW and HW. - * - * hw: Struct containing variables accessed by shared code - * - ***************************************************************************/ -STATIC int32_t -em_get_software_flag(struct em_hw *hw) -{ - int32_t timeout = PHY_CFG_TIMEOUT; - uint32_t extcnf_ctrl; - - DEBUGFUNC("em_get_software_flag"); - - if (hw->mac_type == em_ich8lan || hw->mac_type == em_ich9lan) { - while (timeout) { - extcnf_ctrl = E1000_READ_REG(hw, EXTCNF_CTRL); - extcnf_ctrl |= E1000_EXTCNF_CTRL_SWFLAG; - E1000_WRITE_REG(hw, EXTCNF_CTRL, extcnf_ctrl); - - extcnf_ctrl = E1000_READ_REG(hw, EXTCNF_CTRL); - if (extcnf_ctrl & E1000_EXTCNF_CTRL_SWFLAG) - break; - msec_delay_irq(1); - timeout--; - } - - if (!timeout) { - DEBUGOUT("FW or HW locks the resource too long.\n"); - return -E1000_ERR_CONFIG; - } - } - - return E1000_SUCCESS; -} - -/*************************************************************************** - * - * Release software semaphore FLAG bit (SWFLAG). - * SWFLAG is used to synchronize the access to all shared resource between - * SW, FW and HW. - * - * hw: Struct containing variables accessed by shared code - * - ***************************************************************************/ -STATIC void -em_release_software_flag(struct em_hw *hw) -{ - uint32_t extcnf_ctrl; - - DEBUGFUNC("em_release_software_flag"); - - if (hw->mac_type == em_ich8lan || hw->mac_type == em_ich9lan) { - extcnf_ctrl= E1000_READ_REG(hw, EXTCNF_CTRL); - extcnf_ctrl &= ~E1000_EXTCNF_CTRL_SWFLAG; - E1000_WRITE_REG(hw, EXTCNF_CTRL, extcnf_ctrl); - } - - return; -} - - -/****************************************************************************** - * Reads a 16 bit word or words from the EEPROM using the ICH8's flash access - * register. - * - * hw - Struct containing variables accessed by shared code - * offset - offset of word in the EEPROM to read - * data - word read from the EEPROM - * words - number of words to read - *****************************************************************************/ -STATIC int32_t -em_read_eeprom_ich8(struct em_hw *hw, uint16_t offset, uint16_t words, - uint16_t *data) -{ - int32_t error = E1000_SUCCESS; - uint32_t flash_bank = 0; - uint32_t act_offset = 0; - uint32_t bank_offset = 0; - uint16_t word = 0; - uint16_t i = 0; - - /* We need to know which is the valid flash bank. In the event - * that we didn't allocate eeprom_shadow_ram, we may not be - * managing flash_bank. So it cannot be trusted and needs - * to be updated with each read. - */ - /* Value of bit 22 corresponds to the flash bank we're on. */ - flash_bank = (E1000_READ_REG(hw, EECD) & E1000_EECD_SEC1VAL) ? 1 : 0; - - /* Adjust offset appropriately if we're on bank 1 - adjust for word size */ - bank_offset = flash_bank * (hw->flash_bank_size * 2); - - error = em_get_software_flag(hw); - if (error != E1000_SUCCESS) - return error; - - for (i = 0; i < words; i++) { - if (hw->eeprom_shadow_ram != NULL && - hw->eeprom_shadow_ram[offset+i].modified == TRUE) { - data[i] = hw->eeprom_shadow_ram[offset+i].eeprom_word; - } else { - /* The NVM part needs a byte offset, hence * 2 */ - act_offset = bank_offset + ((offset + i) * 2); - error = em_read_ich8_word(hw, act_offset, &word); - if (error != E1000_SUCCESS) - break; - data[i] = word; - } - } - - em_release_software_flag(hw); - - return error; -} - -/****************************************************************************** - * Writes a 16 bit word or words to the EEPROM using the ICH8's flash access - * register. Actually, writes are written to the shadow ram cache in the hw - * structure hw->em_shadow_ram. em_commit_shadow_ram flushes this to - * the NVM, which occurs when the NVM checksum is updated. - * - * hw - Struct containing variables accessed by shared code - * offset - offset of word in the EEPROM to write - * words - number of words to write - * data - words to write to the EEPROM - *****************************************************************************/ -STATIC int32_t -em_write_eeprom_ich8(struct em_hw *hw, uint16_t offset, uint16_t words, - uint16_t *data) -{ - uint32_t i = 0; - int32_t error = E1000_SUCCESS; - - error = em_get_software_flag(hw); - if (error != E1000_SUCCESS) - return error; - - /* A driver can write to the NVM only if it has eeprom_shadow_ram - * allocated. Subsequent reads to the modified words are read from - * this cached structure as well. Writes will only go into this - * cached structure unless it's followed by a call to - * em_update_eeprom_checksum() where it will commit the changes - * and clear the "modified" field. - */ - if (hw->eeprom_shadow_ram != NULL) { - for (i = 0; i < words; i++) { - if ((offset + i) < E1000_SHADOW_RAM_WORDS) { - hw->eeprom_shadow_ram[offset+i].modified = TRUE; - hw->eeprom_shadow_ram[offset+i].eeprom_word = data[i]; - } else { - error = -E1000_ERR_EEPROM; - break; - } - } - } else { - /* Drivers have the option to not allocate eeprom_shadow_ram as long - * as they don't perform any NVM writes. An attempt in doing so - * will result in this error. - */ - error = -E1000_ERR_EEPROM; - } - - em_release_software_flag(hw); - - return error; -} - -/****************************************************************************** - * This function does initial flash setup so that a new read/write/erase cycle - * can be started. - * - * hw - The pointer to the hw structure - ****************************************************************************/ -STATIC int32_t -em_ich8_cycle_init(struct em_hw *hw) -{ - union ich8_hws_flash_status hsfsts; - int32_t error = E1000_ERR_EEPROM; - int32_t i = 0; - - DEBUGFUNC("em_ich8_cycle_init"); - - hsfsts.regval = E1000_READ_ICH_FLASH_REG16(hw, ICH_FLASH_HSFSTS); - - /* May be check the Flash Des Valid bit in Hw status */ - if (hsfsts.hsf_status.fldesvalid == 0) { - DEBUGOUT("Flash descriptor invalid. SW Sequencing must be used."); - return error; - } - - /* Clear FCERR in Hw status by writing 1 */ - /* Clear DAEL in Hw status by writing a 1 */ - hsfsts.hsf_status.flcerr = 1; - hsfsts.hsf_status.dael = 1; - - E1000_WRITE_ICH_FLASH_REG16(hw, ICH_FLASH_HSFSTS, hsfsts.regval); - - /* Either we should have a hardware SPI cycle in progress bit to check - * against, in order to start a new cycle or FDONE bit should be changed - * in the hardware so that it is 1 after harware reset, which can then be - * used as an indication whether a cycle is in progress or has been - * completed .. we should also have some software semaphore mechanism to - * guard FDONE or the cycle in progress bit so that two threads access to - * those bits can be sequentiallized or a way so that 2 threads dont - * start the cycle at the same time */ - - if (hsfsts.hsf_status.flcinprog == 0) { - /* There is no cycle running at present, so we can start a cycle */ - /* Begin by setting Flash Cycle Done. */ - hsfsts.hsf_status.flcdone = 1; - E1000_WRITE_ICH_FLASH_REG16(hw, ICH_FLASH_HSFSTS, hsfsts.regval); - error = E1000_SUCCESS; - } else { - /* otherwise poll for sometime so the current cycle has a chance - * to end before giving up. */ - for (i = 0; i < ICH_FLASH_COMMAND_TIMEOUT; i++) { - hsfsts.regval = E1000_READ_ICH_FLASH_REG16(hw, ICH_FLASH_HSFSTS); - if (hsfsts.hsf_status.flcinprog == 0) { - error = E1000_SUCCESS; - break; - } - usec_delay(1); - } - if (error == E1000_SUCCESS) { - /* Successful in waiting for previous cycle to timeout, - * now set the Flash Cycle Done. */ - hsfsts.hsf_status.flcdone = 1; - E1000_WRITE_ICH_FLASH_REG16(hw, ICH_FLASH_HSFSTS, hsfsts.regval); - } else { - DEBUGOUT("Flash controller busy, cannot get access"); - } - } - return error; -} - -/****************************************************************************** - * This function starts a flash cycle and waits for its completion - * - * hw - The pointer to the hw structure - ****************************************************************************/ -STATIC int32_t -em_ich8_flash_cycle(struct em_hw *hw, uint32_t timeout) -{ - union ich8_hws_flash_ctrl hsflctl; - union ich8_hws_flash_status hsfsts; - int32_t error = E1000_ERR_EEPROM; - uint32_t i = 0; - - /* Start a cycle by writing 1 in Flash Cycle Go in Hw Flash Control */ - hsflctl.regval = E1000_READ_ICH_FLASH_REG16(hw, ICH_FLASH_HSFCTL); - hsflctl.hsf_ctrl.flcgo = 1; - E1000_WRITE_ICH_FLASH_REG16(hw, ICH_FLASH_HSFCTL, hsflctl.regval); - - /* wait till FDONE bit is set to 1 */ - do { - hsfsts.regval = E1000_READ_ICH_FLASH_REG16(hw, ICH_FLASH_HSFSTS); - if (hsfsts.hsf_status.flcdone == 1) - break; - usec_delay(1); - i++; - } while (i < timeout); - if (hsfsts.hsf_status.flcdone == 1 && hsfsts.hsf_status.flcerr == 0) { - error = E1000_SUCCESS; - } - return error; -} - -/****************************************************************************** - * Reads a byte or word from the NVM using the ICH8 flash access registers. - * - * hw - The pointer to the hw structure - * index - The index of the byte or word to read. - * size - Size of data to read, 1=byte 2=word - * data - Pointer to the word to store the value read. - *****************************************************************************/ -STATIC int32_t -em_read_ich8_data(struct em_hw *hw, uint32_t index, - uint32_t size, uint16_t* data) -{ - union ich8_hws_flash_status hsfsts; - union ich8_hws_flash_ctrl hsflctl; - uint32_t flash_linear_address; - uint32_t flash_data = 0; - int32_t error = -E1000_ERR_EEPROM; - int32_t count = 0; - - DEBUGFUNC("em_read_ich8_data"); - - if (size < 1 || size > 2 || data == 0x0 || - index > ICH_FLASH_LINEAR_ADDR_MASK) - return error; - - flash_linear_address = (ICH_FLASH_LINEAR_ADDR_MASK & index) + - hw->flash_base_addr; - - do { - usec_delay(1); - /* Steps */ - error = em_ich8_cycle_init(hw); - if (error != E1000_SUCCESS) - break; - - hsflctl.regval = E1000_READ_ICH_FLASH_REG16(hw, ICH_FLASH_HSFCTL); - /* 0b/1b corresponds to 1 or 2 byte size, respectively. */ - hsflctl.hsf_ctrl.fldbcount = size - 1; - hsflctl.hsf_ctrl.flcycle = ICH_CYCLE_READ; - E1000_WRITE_ICH_FLASH_REG16(hw, ICH_FLASH_HSFCTL, hsflctl.regval); - - /* Write the last 24 bits of index into Flash Linear address field in - * Flash Address */ - /* TODO: TBD maybe check the index against the size of flash */ - - E1000_WRITE_ICH_FLASH_REG(hw, ICH_FLASH_FADDR, flash_linear_address); - - error = em_ich8_flash_cycle(hw, ICH_FLASH_COMMAND_TIMEOUT); - - /* Check if FCERR is set to 1, if set to 1, clear it and try the whole - * sequence a few more times, else read in (shift in) the Flash Data0, - * the order is least significant byte first msb to lsb */ - if (error == E1000_SUCCESS) { - flash_data = E1000_READ_ICH_FLASH_REG(hw, ICH_FLASH_FDATA0); - if (size == 1) { - *data = (uint8_t)(flash_data & 0x000000FF); - } else if (size == 2) { - *data = (uint16_t)(flash_data & 0x0000FFFF); - } - break; - } else { - /* If we've gotten here, then things are probably completely hosed, - * but if the error condition is detected, it won't hurt to give - * it another try...ICH_FLASH_CYCLE_REPEAT_COUNT times. - */ - hsfsts.regval = E1000_READ_ICH_FLASH_REG16(hw, ICH_FLASH_HSFSTS); - if (hsfsts.hsf_status.flcerr == 1) { - /* Repeat for some time before giving up. */ - continue; - } else if (hsfsts.hsf_status.flcdone == 0) { - DEBUGOUT("Timeout error - flash cycle did not complete."); - break; - } - } - } while (count++ < ICH_FLASH_CYCLE_REPEAT_COUNT); - - return error; -} - -/****************************************************************************** - * Writes One /two bytes to the NVM using the ICH8 flash access registers. - * - * hw - The pointer to the hw structure - * index - The index of the byte/word to read. - * size - Size of data to read, 1=byte 2=word - * data - The byte(s) to write to the NVM. - *****************************************************************************/ -STATIC int32_t -em_write_ich8_data(struct em_hw *hw, uint32_t index, uint32_t size, - uint16_t data) -{ - union ich8_hws_flash_status hsfsts; - union ich8_hws_flash_ctrl hsflctl; - uint32_t flash_linear_address; - uint32_t flash_data = 0; - int32_t error = -E1000_ERR_EEPROM; - int32_t count = 0; - - DEBUGFUNC("em_write_ich8_data"); - - if (size < 1 || size > 2 || data > size * 0xff || - index > ICH_FLASH_LINEAR_ADDR_MASK) - return error; - - flash_linear_address = (ICH_FLASH_LINEAR_ADDR_MASK & index) + - hw->flash_base_addr; - - do { - usec_delay(1); - /* Steps */ - error = em_ich8_cycle_init(hw); - if (error != E1000_SUCCESS) - break; - - hsflctl.regval = E1000_READ_ICH_FLASH_REG16(hw, ICH_FLASH_HSFCTL); - /* 0b/1b corresponds to 1 or 2 byte size, respectively. */ - hsflctl.hsf_ctrl.fldbcount = size -1; - hsflctl.hsf_ctrl.flcycle = ICH_CYCLE_WRITE; - E1000_WRITE_ICH_FLASH_REG16(hw, ICH_FLASH_HSFCTL, hsflctl.regval); - - /* Write the last 24 bits of index into Flash Linear address field in - * Flash Address */ - E1000_WRITE_ICH_FLASH_REG(hw, ICH_FLASH_FADDR, flash_linear_address); - - if (size == 1) - flash_data = (uint32_t)data & 0x00FF; - else - flash_data = (uint32_t)data; - - E1000_WRITE_ICH_FLASH_REG(hw, ICH_FLASH_FDATA0, flash_data); - - /* check if FCERR is set to 1 , if set to 1, clear it and try the whole - * sequence a few more times else done */ - error = em_ich8_flash_cycle(hw, ICH_FLASH_COMMAND_TIMEOUT); - if (error == E1000_SUCCESS) { - break; - } else { - /* If we're here, then things are most likely completely hosed, - * but if the error condition is detected, it won't hurt to give - * it another try...ICH_FLASH_CYCLE_REPEAT_COUNT times. - */ - hsfsts.regval = E1000_READ_ICH_FLASH_REG16(hw, ICH_FLASH_HSFSTS); - if (hsfsts.hsf_status.flcerr == 1) { - /* Repeat for some time before giving up. */ - continue; - } else if (hsfsts.hsf_status.flcdone == 0) { - DEBUGOUT("Timeout error - flash cycle did not complete."); - break; - } - } - } while (count++ < ICH_FLASH_CYCLE_REPEAT_COUNT); - - return error; -} - -/****************************************************************************** - * Reads a single byte from the NVM using the ICH8 flash access registers. - * - * hw - pointer to em_hw structure - * index - The index of the byte to read. - * data - Pointer to a byte to store the value read. - *****************************************************************************/ -STATIC int32_t -em_read_ich8_byte(struct em_hw *hw, uint32_t index, uint8_t* data) -{ - int32_t status = E1000_SUCCESS; - uint16_t word = 0; - - status = em_read_ich8_data(hw, index, 1, &word); - if (status == E1000_SUCCESS) { - *data = (uint8_t)word; - } - - return status; -} - -/****************************************************************************** - * Writes a single byte to the NVM using the ICH8 flash access registers. - * Performs verification by reading back the value and then going through - * a retry algorithm before giving up. - * - * hw - pointer to em_hw structure - * index - The index of the byte to write. - * byte - The byte to write to the NVM. - *****************************************************************************/ -STATIC int32_t -em_verify_write_ich8_byte(struct em_hw *hw, uint32_t index, uint8_t byte) -{ - int32_t error = E1000_SUCCESS; - int32_t program_retries = 0; - - DEBUGOUT2("Byte := %2.2X Offset := %d\n", byte, index); - - error = em_write_ich8_byte(hw, index, byte); - - if (error != E1000_SUCCESS) { - for (program_retries = 0; program_retries < 100; program_retries++) { - DEBUGOUT2("Retrying \t Byte := %2.2X Offset := %d\n", byte, index); - error = em_write_ich8_byte(hw, index, byte); - usec_delay(100); - if (error == E1000_SUCCESS) - break; - } - } - - if (program_retries == 100) - error = E1000_ERR_EEPROM; - - return error; -} - -/****************************************************************************** - * Writes a single byte to the NVM using the ICH8 flash access registers. - * - * hw - pointer to em_hw structure - * index - The index of the byte to read. - * data - The byte to write to the NVM. - *****************************************************************************/ -STATIC int32_t -em_write_ich8_byte(struct em_hw *hw, uint32_t index, uint8_t data) -{ - int32_t status = E1000_SUCCESS; - uint16_t word = (uint16_t)data; - - status = em_write_ich8_data(hw, index, 1, word); - - return status; -} - -/****************************************************************************** - * Reads a word from the NVM using the ICH8 flash access registers. - * - * hw - pointer to em_hw structure - * index - The starting byte index of the word to read. - * data - Pointer to a word to store the value read. - *****************************************************************************/ -STATIC int32_t -em_read_ich8_word(struct em_hw *hw, uint32_t index, uint16_t *data) -{ - int32_t status = E1000_SUCCESS; - status = em_read_ich8_data(hw, index, 2, data); - return status; -} - - -/****************************************************************************** - * Erases the bank specified. Each bank may be a 4, 8 or 64k block. Banks are 0 - * based. - * - * hw - pointer to em_hw structure - * bank - 0 for first bank, 1 for second bank - * - * Note that this function may actually erase as much as 8 or 64 KBytes. The - * amount of NVM used in each bank is a *minimum* of 4 KBytes, but in fact the - * bank size may be 4, 8 or 64 KBytes - *****************************************************************************/ -int32_t -em_erase_ich8_4k_segment(struct em_hw *hw, uint32_t bank) -{ - union ich8_hws_flash_status hsfsts; - union ich8_hws_flash_ctrl hsflctl; - uint32_t flash_linear_address; - int32_t count = 0; - int32_t error = E1000_ERR_EEPROM; - int32_t iteration; - int32_t sub_sector_size = 0; - int32_t bank_size; - int32_t j = 0; - int32_t error_flag = 0; - - hsfsts.regval = E1000_READ_ICH_FLASH_REG16(hw, ICH_FLASH_HSFSTS); - - /* Determine HW Sector size: Read BERASE bits of Hw flash Status register */ - /* 00: The Hw sector is 256 bytes, hence we need to erase 16 - * consecutive sectors. The start index for the nth Hw sector can be - * calculated as bank * 4096 + n * 256 - * 01: The Hw sector is 4K bytes, hence we need to erase 1 sector. - * The start index for the nth Hw sector can be calculated - * as bank * 4096 - * 10: The HW sector is 8K bytes - * 11: The Hw sector size is 64K bytes */ - if (hsfsts.hsf_status.berasesz == 0x0) { - /* Hw sector size 256 */ - sub_sector_size = ICH_FLASH_SEG_SIZE_256; - bank_size = ICH_FLASH_SECTOR_SIZE; - iteration = ICH_FLASH_SECTOR_SIZE / ICH_FLASH_SEG_SIZE_256; - } else if (hsfsts.hsf_status.berasesz == 0x1) { - bank_size = ICH_FLASH_SEG_SIZE_4K; - iteration = 1; - } else if (hsfsts.hsf_status.berasesz == 0x2) { - if (hw->mac_type == em_ich9lan) { - uint32_t gfpreg, sector_base_addr, sector_end_addr; - - gfpreg = E1000_READ_ICH_FLASH_REG(hw, ICH_FLASH_GFPREG); - - /* - * sector_X_addr is a "sector"-aligned address (4096 bytes) - * Add 1 to sector_end_addr since this sector is included in - * the overall size. - */ - sector_base_addr = gfpreg & ICH_GFPREG_BASE_MASK; - sector_end_addr = ((gfpreg >> 16) & ICH_GFPREG_BASE_MASK) + 1; - - /* - * find total size of the NVM, then cut in half since the tota - * size represents two separate NVM banks. - */ - bank_size = (sector_end_addr - sector_base_addr) - << ICH_FLAGH_SECT_ADDR_SHIFT; - bank_size /= 2; - /* Word align */ - bank_size = (bank_size / sizeof(uint16_t)) * sizeof(uint16_t); - - sub_sector_size = ICH_FLASH_SEG_SIZE_8K; - iteration = bank_size / ICH_FLASH_SEG_SIZE_8K; - } else { - return error; - } - } else if (hsfsts.hsf_status.berasesz == 0x3) { - bank_size = ICH_FLASH_SEG_SIZE_64K; - iteration = 1; - } else { - return error; - } - - for (j = 0; j < iteration ; j++) { - do { - count++; - /* Steps */ - error = em_ich8_cycle_init(hw); - if (error != E1000_SUCCESS) { - error_flag = 1; - break; - } - - /* Write a value 11 (block Erase) in Flash Cycle field in Hw flash - * Control */ - hsflctl.regval = E1000_READ_ICH_FLASH_REG16(hw, ICH_FLASH_HSFCTL); - hsflctl.hsf_ctrl.flcycle = ICH_CYCLE_ERASE; - E1000_WRITE_ICH_FLASH_REG16(hw, ICH_FLASH_HSFCTL, hsflctl.regval); - - /* Write the last 24 bits of an index within the block into Flash - * Linear address field in Flash Address. This probably needs to - * be calculated here based off the on-chip erase sector size and - * the software bank size (4, 8 or 64 KBytes) */ - flash_linear_address = bank * bank_size + j * sub_sector_size; - flash_linear_address += hw->flash_base_addr; - flash_linear_address &= ICH_FLASH_LINEAR_ADDR_MASK; - - E1000_WRITE_ICH_FLASH_REG(hw, ICH_FLASH_FADDR, flash_linear_address); - - error = em_ich8_flash_cycle(hw, ICH_FLASH_ERASE_TIMEOUT); - /* Check if FCERR is set to 1. If 1, clear it and try the whole - * sequence a few more times else Done */ - if (error == E1000_SUCCESS) { - break; - } else { - hsfsts.regval = E1000_READ_ICH_FLASH_REG16(hw, ICH_FLASH_HSFSTS); - if (hsfsts.hsf_status.flcerr == 1) { - /* repeat for some time before giving up */ - continue; - } else if (hsfsts.hsf_status.flcdone == 0) { - error_flag = 1; - break; - } - } - } while ((count < ICH_FLASH_CYCLE_REPEAT_COUNT) && !error_flag); - if (error_flag == 1) - break; - } - if (error_flag != 1) - error = E1000_SUCCESS; - return error; -} - - -STATIC int32_t -em_init_lcd_from_nvm_config_region(struct em_hw *hw, - uint32_t cnf_base_addr, uint32_t cnf_size) -{ - uint32_t ret_val = E1000_SUCCESS; - uint16_t word_addr, reg_data, reg_addr; - uint16_t i; - - /* cnf_base_addr is in DWORD */ - word_addr = (uint16_t)(cnf_base_addr << 1); - - /* cnf_size is returned in size of dwords */ - for (i = 0; i < cnf_size; i++) { - ret_val = em_read_eeprom(hw, (word_addr + i*2), 1, ®_data); - if (ret_val) - return ret_val; - - ret_val = em_read_eeprom(hw, (word_addr + i*2 + 1), 1, ®_addr); - if (ret_val) - return ret_val; - - ret_val = em_get_software_flag(hw); - if (ret_val != E1000_SUCCESS) - return ret_val; - - ret_val = em_write_phy_reg_ex(hw, (uint32_t)reg_addr, reg_data); - - em_release_software_flag(hw); - } - - return ret_val; -} - - -/****************************************************************************** - * This function initializes the PHY from the NVM on ICH8 platforms. This - * is needed due to an issue where the NVM configuration is not properly - * autoloaded after power transitions. Therefore, after each PHY reset, we - * will load the configuration data out of the NVM manually. - * - * hw: Struct containing variables accessed by shared code - *****************************************************************************/ -STATIC int32_t -em_init_lcd_from_nvm(struct em_hw *hw) -{ - uint32_t reg_data, cnf_base_addr, cnf_size, ret_val, loop; - - if (hw->phy_type != em_phy_igp_3) - return E1000_SUCCESS; - - /* Check if SW needs configure the PHY */ - reg_data = E1000_READ_REG(hw, FEXTNVM); - if (!(reg_data & FEXTNVM_SW_CONFIG)) - return E1000_SUCCESS; - - /* Wait for basic configuration completes before proceeding*/ - loop = 0; - do { - reg_data = E1000_READ_REG(hw, STATUS) & E1000_STATUS_LAN_INIT_DONE; - usec_delay(100); - loop++; - } while ((!reg_data) && (loop < 50)); - - /* Clear the Init Done bit for the next init event */ - reg_data = E1000_READ_REG(hw, STATUS); - reg_data &= ~E1000_STATUS_LAN_INIT_DONE; - E1000_WRITE_REG(hw, STATUS, reg_data); - - /* Make sure HW does not configure LCD from PHY extended configuration - before SW configuration */ - reg_data = E1000_READ_REG(hw, EXTCNF_CTRL); - if ((reg_data & E1000_EXTCNF_CTRL_LCD_WRITE_ENABLE) == 0x0000) { - reg_data = E1000_READ_REG(hw, EXTCNF_SIZE); - cnf_size = reg_data & E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH; - cnf_size >>= 16; - if (cnf_size) { - reg_data = E1000_READ_REG(hw, EXTCNF_CTRL); - cnf_base_addr = reg_data & E1000_EXTCNF_CTRL_EXT_CNF_POINTER; - /* cnf_base_addr is in DWORD */ - cnf_base_addr >>= 16; - - /* Configure LCD from extended configuration region. */ - ret_val = em_init_lcd_from_nvm_config_region(hw, cnf_base_addr, - cnf_size); - if (ret_val) - return ret_val; - } - } - - return E1000_SUCCESS; -} - diff --git a/sys/dev/netif/em/if_em_hw.h b/sys/dev/netif/em/if_em_hw.h deleted file mode 100644 index 60a69645c7..0000000000 --- a/sys/dev/netif/em/if_em_hw.h +++ /dev/null @@ -1,3392 +0,0 @@ -/******************************************************************************* -Copyright (c) 2001-2005, Intel Corporation -All rights reserved. - -Redistribution and use in source and binary forms, with or without -modification, are permitted provided that the following conditions are met: - - 1. Redistributions of source code must retain the above copyright notice, - this list of conditions and the following disclaimer. - - 2. Redistributions in binary form must reproduce the above copyright - notice, this list of conditions and the following disclaimer in the - documentation and/or other materials provided with the distribution. - - 3. Neither the name of the Intel Corporation nor the names of its - contributors may be used to endorse or promote products derived from - this software without specific prior written permission. - -THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" -AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE -IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE -ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE -LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR -CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF -SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS -INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN -CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) -ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE -POSSIBILITY OF SUCH DAMAGE. -*******************************************************************************/ - -/*$FreeBSD: src/sys/dev/em/if_em_hw.h,v 1.1.2.8 2003/06/09 21:43:41 pdeuskar Exp $*/ -/*$DragonFly: src/sys/dev/netif/em/if_em_hw.h,v 1.13 2008/01/11 10:34:15 sephe Exp $*/ - -/* if_em_hw.h - * Structures, enums, and macros for the MAC - */ - -#ifndef _EM_HW_H_ -#define _EM_HW_H_ - -#ifdef LM -#include "if_em_osdep.h" -#else -#include -#endif - - -/* Forward declarations of structures used by the shared code */ -struct em_hw; -struct em_hw_stats; - -/* Enumerated types specific to the e1000 hardware */ -/* Media Access Controlers */ -typedef enum { - em_undefined = 0, - em_82542_rev2_0, - em_82542_rev2_1, - em_82543, - em_82544, - em_82540, - em_82545, - em_82545_rev_3, - em_82546, - em_82546_rev_3, - em_82541, - em_82541_rev_2, - em_82547, - em_82547_rev_2, - em_82571, - em_82572, - em_82573, - em_80003es2lan, - em_ich8lan, - em_ich9lan, - em_num_macs -} em_mac_type; - -typedef enum { - em_eeprom_uninitialized = 0, - em_eeprom_spi, - em_eeprom_microwire, - em_eeprom_flash, - em_eeprom_ich8, - em_eeprom_none, /* No NVM support */ - em_num_eeprom_types -} em_eeprom_type; - -/* Media Types */ -typedef enum { - em_media_type_copper = 0, - em_media_type_fiber = 1, - em_media_type_internal_serdes = 2, - em_num_media_types -} em_media_type; - -typedef enum { - em_10_half = 0, - em_10_full = 1, - em_100_half = 2, - em_100_full = 3 -} em_speed_duplex_type; - -struct em_shadow_ram { - uint16_t eeprom_word; - boolean_t modified; -}; - -/* PCI bus types */ -typedef enum { - em_bus_type_unknown = 0, - em_bus_type_pci, - em_bus_type_pcix, - em_bus_type_pci_express, - em_bus_type_reserved -} em_bus_type; - -/* PCI bus speeds */ -typedef enum { - em_bus_speed_unknown = 0, - em_bus_speed_33, - em_bus_speed_66, - em_bus_speed_100, - em_bus_speed_120, - em_bus_speed_133, - em_bus_speed_2500, - em_bus_speed_reserved -} em_bus_speed; - -/* PCI bus widths */ -typedef enum { - em_bus_width_unknown = 0, - /* These PCIe values should literally match the possible return values - * from config space */ - em_bus_width_pciex_1 = 1, - em_bus_width_pciex_2 = 2, - em_bus_width_pciex_4 = 4, - em_bus_width_32, - em_bus_width_64, - em_bus_width_reserved -} em_bus_width; - -/* PHY status info structure and supporting enums */ -typedef enum { - em_cable_length_50 = 0, - em_cable_length_50_80, - em_cable_length_80_110, - em_cable_length_110_140, - em_cable_length_140, - em_cable_length_undefined = 0xFF -} em_cable_length; - -typedef enum { - em_gg_cable_length_60 = 0, - em_gg_cable_length_60_115 = 1, - em_gg_cable_length_115_150 = 2, - em_gg_cable_length_150 = 4 -} em_gg_cable_length; - -typedef enum { - em_igp_cable_length_10 = 10, - em_igp_cable_length_20 = 20, - em_igp_cable_length_30 = 30, - em_igp_cable_length_40 = 40, - em_igp_cable_length_50 = 50, - em_igp_cable_length_60 = 60, - em_igp_cable_length_70 = 70, - em_igp_cable_length_80 = 80, - em_igp_cable_length_90 = 90, - em_igp_cable_length_100 = 100, - em_igp_cable_length_110 = 110, - em_igp_cable_length_115 = 115, - em_igp_cable_length_120 = 120, - em_igp_cable_length_130 = 130, - em_igp_cable_length_140 = 140, - em_igp_cable_length_150 = 150, - em_igp_cable_length_160 = 160, - em_igp_cable_length_170 = 170, - em_igp_cable_length_180 = 180 -} em_igp_cable_length; - -typedef enum { - em_10bt_ext_dist_enable_normal = 0, - em_10bt_ext_dist_enable_lower, - em_10bt_ext_dist_enable_undefined = 0xFF -} em_10bt_ext_dist_enable; - -typedef enum { - em_rev_polarity_normal = 0, - em_rev_polarity_reversed, - em_rev_polarity_undefined = 0xFF -} em_rev_polarity; - -typedef enum { - em_downshift_normal = 0, - em_downshift_activated, - em_downshift_undefined = 0xFF -} em_downshift; - -typedef enum { - em_smart_speed_default = 0, - em_smart_speed_on, - em_smart_speed_off -} em_smart_speed; - -typedef enum { - em_polarity_reversal_enabled = 0, - em_polarity_reversal_disabled, - em_polarity_reversal_undefined = 0xFF -} em_polarity_reversal; - -typedef enum { - em_auto_x_mode_manual_mdi = 0, - em_auto_x_mode_manual_mdix, - em_auto_x_mode_auto1, - em_auto_x_mode_auto2, - em_auto_x_mode_undefined = 0xFF -} em_auto_x_mode; - -typedef enum { - em_1000t_rx_status_not_ok = 0, - em_1000t_rx_status_ok, - em_1000t_rx_status_undefined = 0xFF -} em_1000t_rx_status; - -typedef enum { - em_phy_m88 = 0, - em_phy_igp, - em_phy_igp_2, - em_phy_gg82563, - em_phy_igp_3, - em_phy_ife, - em_phy_undefined = 0xFF -} em_phy_type; - -typedef enum { - em_ms_hw_default = 0, - em_ms_force_master, - em_ms_force_slave, - em_ms_auto -} em_ms_type; - -typedef enum { - em_ffe_config_enabled = 0, - em_ffe_config_active, - em_ffe_config_blocked -} em_ffe_config; - -typedef enum { - em_dsp_config_disabled = 0, - em_dsp_config_enabled, - em_dsp_config_activated, - em_dsp_config_undefined = 0xFF -} em_dsp_config; - -struct em_phy_info { - em_cable_length cable_length; - em_10bt_ext_dist_enable extended_10bt_distance; - em_rev_polarity cable_polarity; - em_downshift downshift; - em_polarity_reversal polarity_correction; - em_auto_x_mode mdix_mode; - em_1000t_rx_status local_rx; - em_1000t_rx_status remote_rx; -}; - -struct em_phy_stats { - uint32_t idle_errors; - uint32_t receive_errors; -}; - -struct em_eeprom_info { - em_eeprom_type type; - uint16_t word_size; - uint16_t opcode_bits; - uint16_t address_bits; - uint16_t delay_usec; - uint16_t page_size; - boolean_t use_eerd; - boolean_t use_eewr; -}; - -/* Flex ASF Information */ -#define E1000_HOST_IF_MAX_SIZE 2048 - -typedef enum { - em_byte_align = 0, - em_word_align = 1, - em_dword_align = 2 -} em_align_type; - - - -/* Error Codes */ -#define E1000_SUCCESS 0 -#define E1000_ERR_EEPROM 1 -#define E1000_ERR_PHY 2 -#define E1000_ERR_CONFIG 3 -#define E1000_ERR_PARAM 4 -#define E1000_ERR_MAC_TYPE 5 -#define E1000_ERR_PHY_TYPE 6 -#define E1000_ERR_RESET 9 -#define E1000_ERR_MASTER_REQUESTS_PENDING 10 -#define E1000_ERR_HOST_INTERFACE_COMMAND 11 -#define E1000_BLK_PHY_RESET 12 -#define E1000_ERR_SWFW_SYNC 13 - -#define E1000_BYTE_SWAP_WORD(_value) ((((_value) & 0x00ff) << 8) | \ - (((_value) & 0xff00) >> 8)) - -/* Function prototypes */ -/* Initialization */ -int32_t em_reset_hw(struct em_hw *hw); -int32_t em_init_hw(struct em_hw *hw); -int32_t em_set_mac_type(struct em_hw *hw); -void em_set_media_type(struct em_hw *hw); - -/* Link Configuration */ -int32_t em_setup_link(struct em_hw *hw); -int32_t em_phy_setup_autoneg(struct em_hw *hw); -void em_config_collision_dist(struct em_hw *hw); -int32_t em_check_for_link(struct em_hw *hw); -int32_t em_get_speed_and_duplex(struct em_hw *hw, uint16_t *speed, uint16_t *duplex); -int32_t em_force_mac_fc(struct em_hw *hw); - - -/* PHY */ -int32_t em_read_phy_reg(struct em_hw *hw, uint32_t reg_addr, uint16_t *phy_data); -int32_t em_write_phy_reg(struct em_hw *hw, uint32_t reg_addr, uint16_t data); -int32_t em_phy_hw_reset(struct em_hw *hw); -int32_t em_phy_reset(struct em_hw *hw); -int32_t em_phy_get_info(struct em_hw *hw, struct em_phy_info *phy_info); -int32_t em_validate_mdi_setting(struct em_hw *hw); - -void em_phy_powerdown_workaround(struct em_hw *hw); - -/* EEPROM Functions */ -int32_t em_init_eeprom_params(struct em_hw *hw); - -/* MNG HOST IF functions */ -uint32_t em_enable_mng_pass_thru(struct em_hw *hw); - -#define E1000_MNG_DHCP_TX_PAYLOAD_CMD 64 -#define E1000_HI_MAX_MNG_DATA_LENGTH 0x6F8 /* Host Interface data length */ - -#define E1000_MNG_DHCP_COMMAND_TIMEOUT 10 /* Time in ms to process MNG command */ -#define E1000_MNG_DHCP_COOKIE_OFFSET 0x6F0 /* Cookie offset */ -#define E1000_MNG_DHCP_COOKIE_LENGTH 0x10 /* Cookie length */ -#define E1000_MNG_IAMT_MODE 0x3 -#define E1000_MNG_ICH_IAMT_MODE 0x2 -#define E1000_IAMT_SIGNATURE 0x544D4149 /* Intel(R) Active Management Technology signature */ - -#define E1000_MNG_DHCP_COOKIE_STATUS_PARSING_SUPPORT 0x1 /* DHCP parsing enabled */ -#define E1000_MNG_DHCP_COOKIE_STATUS_VLAN_SUPPORT 0x2 /* DHCP parsing enabled */ -#define E1000_VFTA_ENTRY_SHIFT 0x5 -#define E1000_VFTA_ENTRY_MASK 0x7F -#define E1000_VFTA_ENTRY_BIT_SHIFT_MASK 0x1F - -struct em_host_mng_command_header { - uint8_t command_id; - uint8_t checksum; - uint16_t reserved1; - uint16_t reserved2; - uint16_t command_length; -}; - -struct em_host_mng_command_info { - struct em_host_mng_command_header command_header; /* Command Head/Command Result Head has 4 bytes */ - uint8_t command_data[E1000_HI_MAX_MNG_DATA_LENGTH]; /* Command data can length 0..0x658*/ -}; -struct em_host_mng_dhcp_cookie{ - uint32_t signature; - uint8_t status; - uint8_t reserved0; - uint16_t vlan_id; - uint32_t reserved1; - uint16_t reserved2; - uint8_t reserved3; - uint8_t checksum; -}; - -int32_t em_read_part_num(struct em_hw *hw, uint32_t * part_num); -int32_t em_mng_write_dhcp_info(struct em_hw *hw, uint8_t *buffer, - uint16_t length); -boolean_t em_check_mng_mode(struct em_hw *hw); -boolean_t em_enable_tx_pkt_filtering(struct em_hw *hw); -int32_t em_read_eeprom(struct em_hw *hw, uint16_t reg, uint16_t words, uint16_t *data); -int32_t em_validate_eeprom_checksum(struct em_hw *hw); -int32_t em_update_eeprom_checksum(struct em_hw *hw); -int32_t em_write_eeprom(struct em_hw *hw, uint16_t reg, uint16_t words, uint16_t *data); -int32_t em_read_mac_addr(struct em_hw * hw); - - -/* Filters (multicast, vlan, receive) */ -void em_mc_addr_list_update(struct em_hw *hw, uint8_t * mc_addr_list, uint32_t mc_addr_count, uint32_t pad, uint32_t rar_used_count); -uint32_t em_hash_mc_addr(struct em_hw *hw, uint8_t * mc_addr); -void em_mta_set(struct em_hw *hw, uint32_t hash_value); -void em_rar_set(struct em_hw *hw, uint8_t * mc_addr, uint32_t rar_index); -void em_write_vfta(struct em_hw *hw, uint32_t offset, uint32_t value); - -/* LED functions */ -int32_t em_setup_led(struct em_hw *hw); -int32_t em_cleanup_led(struct em_hw *hw); -int32_t em_led_on(struct em_hw *hw); -int32_t em_led_off(struct em_hw *hw); -int32_t em_blink_led_start(struct em_hw *hw); - -/* Adaptive IFS Functions */ - -/* Everything else */ -void em_clear_hw_cntrs(struct em_hw *hw); - -void em_reset_adaptive(struct em_hw *hw); -void em_update_adaptive(struct em_hw *hw); -void em_tbi_adjust_stats(struct em_hw *hw, struct em_hw_stats *stats, uint32_t frame_len, uint8_t * mac_addr); -void em_get_bus_info(struct em_hw *hw); -void em_pci_set_mwi(struct em_hw *hw); -void em_pci_clear_mwi(struct em_hw *hw); -void em_read_pci_cfg(struct em_hw *hw, uint32_t reg, uint16_t * value); -void em_write_pci_cfg(struct em_hw *hw, uint32_t reg, uint16_t * value); -int32_t em_read_pcie_cap_reg(struct em_hw *hw, uint32_t reg, uint16_t *value); -/* Port I/O is only supported on 82544 and newer */ -uint32_t em_io_read(struct em_hw *hw, unsigned long port); -void em_io_write(struct em_hw *hw, unsigned long port, uint32_t value); -int32_t em_disable_pciex_master(struct em_hw *hw); -int32_t em_check_phy_reset_block(struct em_hw *hw); - - - -#ifndef E1000_READ_REG_IO -#define E1000_READ_REG_IO(a, reg) \ - em_read_reg_io((a), E1000_##reg) -#define E1000_WRITE_REG_IO(a, reg, val) \ - em_write_reg_io((a), E1000_##reg, val) -#endif - -/* PCI Device IDs */ -#define E1000_DEV_ID_82542 0x1000 -#define E1000_DEV_ID_82543GC_FIBER 0x1001 -#define E1000_DEV_ID_82543GC_COPPER 0x1004 -#define E1000_DEV_ID_82544EI_COPPER 0x1008 -#define E1000_DEV_ID_82544EI_FIBER 0x1009 -#define E1000_DEV_ID_82544GC_COPPER 0x100C -#define E1000_DEV_ID_82544GC_LOM 0x100D -#define E1000_DEV_ID_82540EM 0x100E -#define E1000_DEV_ID_82540EM_LOM 0x1015 -#define E1000_DEV_ID_82540EP_LOM 0x1016 -#define E1000_DEV_ID_82540EP 0x1017 -#define E1000_DEV_ID_82540EP_LP 0x101E -#define E1000_DEV_ID_82545EM_COPPER 0x100F -#define E1000_DEV_ID_82545EM_FIBER 0x1011 -#define E1000_DEV_ID_82545GM_COPPER 0x1026 -#define E1000_DEV_ID_82545GM_FIBER 0x1027 -#define E1000_DEV_ID_82545GM_SERDES 0x1028 -#define E1000_DEV_ID_82546EB_COPPER 0x1010 -#define E1000_DEV_ID_82546EB_FIBER 0x1012 -#define E1000_DEV_ID_82546EB_QUAD_COPPER 0x101D -#define E1000_DEV_ID_82541EI 0x1013 -#define E1000_DEV_ID_82541EI_MOBILE 0x1018 -#define E1000_DEV_ID_82541ER_LOM 0x1014 -#define E1000_DEV_ID_82541ER 0x1078 -#define E1000_DEV_ID_82547GI 0x1075 -#define E1000_DEV_ID_82541GI 0x1076 -#define E1000_DEV_ID_82541GI_MOBILE 0x1077 -#define E1000_DEV_ID_82541GI_LF 0x107C -#define E1000_DEV_ID_82546GB_COPPER 0x1079 -#define E1000_DEV_ID_82546GB_FIBER 0x107A -#define E1000_DEV_ID_82546GB_SERDES 0x107B -#define E1000_DEV_ID_82546GB_PCIE 0x108A -#define E1000_DEV_ID_82546GB_QUAD_COPPER 0x1099 -#define E1000_DEV_ID_82547EI 0x1019 -#define E1000_DEV_ID_82547EI_MOBILE 0x101A -#define E1000_DEV_ID_82571EB_COPPER 0x105E -#define E1000_DEV_ID_82571EB_FIBER 0x105F -#define E1000_DEV_ID_82571EB_QUAD_FIBER 0x10A5 -#define E1000_DEV_ID_82571PT_QUAD_COPPER 0x10D5 -#define E1000_DEV_ID_82571EB_SERDES 0x1060 -#define E1000_DEV_ID_82571EB_QUAD_COPPER 0x10A4 -#define E1000_DEV_ID_82571EB_QUAD_COPPER_LOWPROFILE 0x10BC -#define E1000_DEV_ID_82572EI_COPPER 0x107D -#define E1000_DEV_ID_82572EI_FIBER 0x107E -#define E1000_DEV_ID_82572EI_SERDES 0x107F -#define E1000_DEV_ID_82572EI 0x10B9 -#define E1000_DEV_ID_82573E 0x108B -#define E1000_DEV_ID_82573E_IAMT 0x108C -#define E1000_DEV_ID_82573L 0x109A -#define E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3 0x10B5 -#define E1000_DEV_ID_80003ES2LAN_COPPER_DPT 0x1096 -#define E1000_DEV_ID_80003ES2LAN_SERDES_DPT 0x1098 -#define E1000_DEV_ID_80003ES2LAN_COPPER_SPT 0x10BA -#define E1000_DEV_ID_80003ES2LAN_SERDES_SPT 0x10BB - -#define E1000_DEV_ID_ICH8_IGP_M_AMT 0x1049 -#define E1000_DEV_ID_ICH8_IGP_AMT 0x104A -#define E1000_DEV_ID_ICH8_IGP_C 0x104B -#define E1000_DEV_ID_ICH8_IFE 0x104C -#define E1000_DEV_ID_ICH8_IFE_GT 0x10C4 -#define E1000_DEV_ID_ICH8_IFE_G 0x10C5 -#define E1000_DEV_ID_ICH8_IGP_M 0x104D -#define E1000_DEV_ID_ICH9_IGP_AMT 0x10BD -#define E1000_DEV_ID_ICH9_IGP_C 0x294C -#define E1000_DEV_ID_ICH9_IFE 0x10C0 -#define E1000_DEV_ID_ICH9_IFE_GT 0x10C3 -#define E1000_DEV_ID_ICH9_IFE_G 0x10C2 -#define E1000_DEV_ID_82575EB_COPPER 0x10A7 -#define E1000_DEV_ID_82575EB_FIBER_SERDES 0x10A9 -#define E1000_DEV_ID_82575GB_QUAD_COPPER 0x10D6 - - -#define NODE_ADDRESS_SIZE 6 -#define ETH_LENGTH_OF_ADDRESS 6 - -/* MAC decode size is 128K - This is the size of BAR0 */ -#define MAC_DECODE_SIZE (128 * 1024) - -#define E1000_82542_2_0_REV_ID 2 -#define E1000_82542_2_1_REV_ID 3 -#define E1000_REVISION_0 0 -#define E1000_REVISION_1 1 -#define E1000_REVISION_2 2 -#define E1000_REVISION_3 3 - -#define SPEED_10 10 -#define SPEED_100 100 -#define SPEED_1000 1000 -#define HALF_DUPLEX 1 -#define FULL_DUPLEX 2 - -/* The sizes (in bytes) of a ethernet packet */ -#define ENET_HEADER_SIZE 14 -#define MAXIMUM_ETHERNET_FRAME_SIZE 1518 /* With FCS */ -#define MINIMUM_ETHERNET_FRAME_SIZE 64 /* With FCS */ -#define ETHERNET_FCS_SIZE 4 -#define MAXIMUM_ETHERNET_PACKET_SIZE \ - (MAXIMUM_ETHERNET_FRAME_SIZE - ETHERNET_FCS_SIZE) -#define MINIMUM_ETHERNET_PACKET_SIZE \ - (MINIMUM_ETHERNET_FRAME_SIZE - ETHERNET_FCS_SIZE) -#define CRC_LENGTH ETHERNET_FCS_SIZE -#define MAX_JUMBO_FRAME_SIZE 0x3F00 - - -/* 802.1q VLAN Packet Sizes */ -#define VLAN_TAG_SIZE 4 /* 802.3ac tag (not DMAed) */ - -/* Ethertype field values */ -#define ETHERNET_IEEE_VLAN_TYPE 0x8100 /* 802.3ac packet */ -#define ETHERNET_IP_TYPE 0x0800 /* IP packets */ -#define ETHERNET_ARP_TYPE 0x0806 /* Address Resolution Protocol (ARP) */ - -/* Packet Header defines */ -#define IP_PROTOCOL_TCP 6 -#define IP_PROTOCOL_UDP 0x11 - -/* This defines the bits that are set in the Interrupt Mask - * Set/Read Register. Each bit is documented below: - * o RXDMT0 = Receive Descriptor Minimum Threshold hit (ring 0) - * o RXSEQ = Receive Sequence Error - */ -#define POLL_IMS_ENABLE_MASK ( \ - E1000_IMS_RXDMT0 | \ - E1000_IMS_RXSEQ) - -/* This defines the bits that are set in the Interrupt Mask - * Set/Read Register. Each bit is documented below: - * o RXT0 = Receiver Timer Interrupt (ring 0) - * o TXDW = Transmit Descriptor Written Back - * o RXDMT0 = Receive Descriptor Minimum Threshold hit (ring 0) - * o RXSEQ = Receive Sequence Error - * o LSC = Link Status Change - */ -#define IMS_ENABLE_MASK ( \ - E1000_IMS_RXT0 | \ - E1000_IMS_TXDW | \ - E1000_IMS_RXDMT0 | \ - E1000_IMS_RXSEQ | \ - E1000_IMS_LSC) - - -/* Additional interrupts need to be handled for em_ich8lan: - DSW = The FW changed the status of the DISSW bit in FWSM - PHYINT = The LAN connected device generates an interrupt - EPRST = Manageability reset event */ -#define IMS_ICH8LAN_ENABLE_MASK (\ - E1000_IMS_DSW | \ - E1000_IMS_PHYINT | \ - E1000_IMS_EPRST) - - -/* Number of high/low register pairs in the RAR. The RAR (Receive Address - * Registers) holds the directed and multicast addresses that we monitor. We - * reserve one of these spots for our directed address, allowing us room for - * E1000_RAR_ENTRIES - 1 multicast addresses. - */ -#define E1000_RAR_ENTRIES 15 - -#define E1000_RAR_ENTRIES_ICH8LAN 6 - -#define MIN_NUMBER_OF_DESCRIPTORS 8 -#define MAX_NUMBER_OF_DESCRIPTORS 0xFFF8 - -/* Receive Descriptor */ -struct em_rx_desc { - uint64_t buffer_addr; /* Address of the descriptor's data buffer */ - uint16_t length; /* Length of data DMAed into data buffer */ - uint16_t csum; /* Packet checksum */ - uint8_t status; /* Descriptor status */ - uint8_t errors; /* Descriptor Errors */ - uint16_t special; -}; - -/* Receive Descriptor - Extended */ -union em_rx_desc_extended { - struct { - uint64_t buffer_addr; - uint64_t reserved; - } read; - struct { - struct { - uint32_t mrq; /* Multiple Rx Queues */ - union { - uint32_t rss; /* RSS Hash */ - struct { - uint16_t ip_id; /* IP id */ - uint16_t csum; /* Packet Checksum */ - } csum_ip; - } hi_dword; - } lower; - struct { - uint32_t status_error; /* ext status/error */ - uint16_t length; - uint16_t vlan; /* VLAN tag */ - } upper; - } wb; /* writeback */ -}; - -#define MAX_PS_BUFFERS 4 -/* Receive Descriptor - Packet Split */ -union em_rx_desc_packet_split { - struct { - /* one buffer for protocol header(s), three data buffers */ - uint64_t buffer_addr[MAX_PS_BUFFERS]; - } read; - struct { - struct { - uint32_t mrq; /* Multiple Rx Queues */ - union { - uint32_t rss; /* RSS Hash */ - struct { - uint16_t ip_id; /* IP id */ - uint16_t csum; /* Packet Checksum */ - } csum_ip; - } hi_dword; - } lower; - struct { - uint32_t status_error; /* ext status/error */ - uint16_t length0; /* length of buffer 0 */ - uint16_t vlan; /* VLAN tag */ - } middle; - struct { - uint16_t header_status; - uint16_t length[3]; /* length of buffers 1-3 */ - } upper; - uint64_t reserved; - } wb; /* writeback */ -}; - -/* Receive Decriptor bit definitions */ -#define E1000_RXD_STAT_DD 0x01 /* Descriptor Done */ -#define E1000_RXD_STAT_EOP 0x02 /* End of Packet */ -#define E1000_RXD_STAT_IXSM 0x04 /* Ignore checksum */ -#define E1000_RXD_STAT_VP 0x08 /* IEEE VLAN Packet */ -#define E1000_RXD_STAT_UDPCS 0x10 /* UDP xsum caculated */ -#define E1000_RXD_STAT_TCPCS 0x20 /* TCP xsum calculated */ -#define E1000_RXD_STAT_IPCS 0x40 /* IP xsum calculated */ -#define E1000_RXD_STAT_PIF 0x80 /* passed in-exact filter */ -#define E1000_RXD_STAT_IPIDV 0x200 /* IP identification valid */ -#define E1000_RXD_STAT_UDPV 0x400 /* Valid UDP checksum */ -#define E1000_RXD_STAT_ACK 0x8000 /* ACK Packet indication */ -#define E1000_RXD_ERR_CE 0x01 /* CRC Error */ -#define E1000_RXD_ERR_SE 0x02 /* Symbol Error */ -#define E1000_RXD_ERR_SEQ 0x04 /* Sequence Error */ -#define E1000_RXD_ERR_CXE 0x10 /* Carrier Extension Error */ -#define E1000_RXD_ERR_TCPE 0x20 /* TCP/UDP Checksum Error */ -#define E1000_RXD_ERR_IPE 0x40 /* IP Checksum Error */ -#define E1000_RXD_ERR_RXE 0x80 /* Rx Data Error */ -#define E1000_RXD_SPC_VLAN_MASK 0x0FFF /* VLAN ID is in lower 12 bits */ -#define E1000_RXD_SPC_PRI_MASK 0xE000 /* Priority is in upper 3 bits */ -#define E1000_RXD_SPC_PRI_SHIFT 13 -#define E1000_RXD_SPC_CFI_MASK 0x1000 /* CFI is bit 12 */ -#define E1000_RXD_SPC_CFI_SHIFT 12 - -#define E1000_RXDEXT_STATERR_CE 0x01000000 -#define E1000_RXDEXT_STATERR_SE 0x02000000 -#define E1000_RXDEXT_STATERR_SEQ 0x04000000 -#define E1000_RXDEXT_STATERR_CXE 0x10000000 -#define E1000_RXDEXT_STATERR_TCPE 0x20000000 -#define E1000_RXDEXT_STATERR_IPE 0x40000000 -#define E1000_RXDEXT_STATERR_RXE 0x80000000 - -#define E1000_RXDPS_HDRSTAT_HDRSP 0x00008000 -#define E1000_RXDPS_HDRSTAT_HDRLEN_MASK 0x000003FF - -/* mask to determine if packets should be dropped due to frame errors */ -#define E1000_RXD_ERR_FRAME_ERR_MASK ( \ - E1000_RXD_ERR_CE | \ - E1000_RXD_ERR_SE | \ - E1000_RXD_ERR_SEQ | \ - E1000_RXD_ERR_CXE | \ - E1000_RXD_ERR_RXE) - - -/* Same mask, but for extended and packet split descriptors */ -#define E1000_RXDEXT_ERR_FRAME_ERR_MASK ( \ - E1000_RXDEXT_STATERR_CE | \ - E1000_RXDEXT_STATERR_SE | \ - E1000_RXDEXT_STATERR_SEQ | \ - E1000_RXDEXT_STATERR_CXE | \ - E1000_RXDEXT_STATERR_RXE) - - -/* Transmit Descriptor */ -struct em_tx_desc { - uint64_t buffer_addr; /* Address of the descriptor's data buffer */ - union { - uint32_t data; - struct { - uint16_t length; /* Data buffer length */ - uint8_t cso; /* Checksum offset */ - uint8_t cmd; /* Descriptor control */ - } flags; - } lower; - union { - uint32_t data; - struct { - uint8_t status; /* Descriptor status */ - uint8_t css; /* Checksum start */ - uint16_t special; - } fields; - } upper; -}; - -/* Transmit Descriptor bit definitions */ -#define E1000_TXD_DTYP_D 0x00100000 /* Data Descriptor */ -#define E1000_TXD_DTYP_C 0x00000000 /* Context Descriptor */ -#define E1000_TXD_POPTS_IXSM 0x01 /* Insert IP checksum */ -#define E1000_TXD_POPTS_TXSM 0x02 /* Insert TCP/UDP checksum */ -#define E1000_TXD_CMD_EOP 0x01000000 /* End of Packet */ -#define E1000_TXD_CMD_IFCS 0x02000000 /* Insert FCS (Ethernet CRC) */ -#define E1000_TXD_CMD_IC 0x04000000 /* Insert Checksum */ -#define E1000_TXD_CMD_RS 0x08000000 /* Report Status */ -#define E1000_TXD_CMD_RPS 0x10000000 /* Report Packet Sent */ -#define E1000_TXD_CMD_DEXT 0x20000000 /* Descriptor extension (0 = legacy) */ -#define E1000_TXD_CMD_VLE 0x40000000 /* Add VLAN tag */ -#define E1000_TXD_CMD_IDE 0x80000000 /* Enable Tidv register */ -#define E1000_TXD_STAT_DD 0x00000001 /* Descriptor Done */ -#define E1000_TXD_STAT_EC 0x00000002 /* Excess Collisions */ -#define E1000_TXD_STAT_LC 0x00000004 /* Late Collisions */ -#define E1000_TXD_STAT_TU 0x00000008 /* Transmit underrun */ -#define E1000_TXD_CMD_TCP 0x01000000 /* TCP packet */ -#define E1000_TXD_CMD_IP 0x02000000 /* IP packet */ -#define E1000_TXD_CMD_TSE 0x04000000 /* TCP Seg enable */ -#define E1000_TXD_STAT_TC 0x00000004 /* Tx Underrun */ - -/* Offload Context Descriptor */ -struct em_context_desc { - union { - uint32_t ip_config; - struct { - uint8_t ipcss; /* IP checksum start */ - uint8_t ipcso; /* IP checksum offset */ - uint16_t ipcse; /* IP checksum end */ - } ip_fields; - } lower_setup; - union { - uint32_t tcp_config; - struct { - uint8_t tucss; /* TCP checksum start */ - uint8_t tucso; /* TCP checksum offset */ - uint16_t tucse; /* TCP checksum end */ - } tcp_fields; - } upper_setup; - uint32_t cmd_and_length; /* */ - union { - uint32_t data; - struct { - uint8_t status; /* Descriptor status */ - uint8_t hdr_len; /* Header length */ - uint16_t mss; /* Maximum segment size */ - } fields; - } tcp_seg_setup; -}; - -/* Offload data descriptor */ -struct em_data_desc { - uint64_t buffer_addr; /* Address of the descriptor's buffer address */ - union { - uint32_t data; - struct { - uint16_t length; /* Data buffer length */ - uint8_t typ_len_ext; /* */ - uint8_t cmd; /* */ - } flags; - } lower; - union { - uint32_t data; - struct { - uint8_t status; /* Descriptor status */ - uint8_t popts; /* Packet Options */ - uint16_t special; /* */ - } fields; - } upper; -}; - -/* Filters */ -#define E1000_NUM_UNICAST 16 /* Unicast filter entries */ -#define E1000_MC_TBL_SIZE 128 /* Multicast Filter Table (4096 bits) */ -#define E1000_VLAN_FILTER_TBL_SIZE 128 /* VLAN Filter Table (4096 bits) */ - -#define E1000_NUM_UNICAST_ICH8LAN 7 -#define E1000_MC_TBL_SIZE_ICH8LAN 32 - - -/* Receive Address Register */ -struct em_rar { - volatile uint32_t low; /* receive address low */ - volatile uint32_t high; /* receive address high */ -}; - -/* Number of entries in the Multicast Table Array (MTA). */ -#define E1000_NUM_MTA_REGISTERS 128 -#define E1000_NUM_MTA_REGISTERS_ICH8LAN 32 - -/* IPv4 Address Table Entry */ -struct em_ipv4_at_entry { - volatile uint32_t ipv4_addr; /* IP Address (RW) */ - volatile uint32_t reserved; -}; - -/* Four wakeup IP addresses are supported */ -#define E1000_WAKEUP_IP_ADDRESS_COUNT_MAX 4 -#define E1000_IP4AT_SIZE E1000_WAKEUP_IP_ADDRESS_COUNT_MAX -#define E1000_IP4AT_SIZE_ICH8LAN 3 -#define E1000_IP6AT_SIZE 1 - -/* IPv6 Address Table Entry */ -struct em_ipv6_at_entry { - volatile uint8_t ipv6_addr[16]; -}; - -/* Flexible Filter Length Table Entry */ -struct em_fflt_entry { - volatile uint32_t length; /* Flexible Filter Length (RW) */ - volatile uint32_t reserved; -}; - -/* Flexible Filter Mask Table Entry */ -struct em_ffmt_entry { - volatile uint32_t mask; /* Flexible Filter Mask (RW) */ - volatile uint32_t reserved; -}; - -/* Flexible Filter Value Table Entry */ -struct em_ffvt_entry { - volatile uint32_t value; /* Flexible Filter Value (RW) */ - volatile uint32_t reserved; -}; - -/* Four Flexible Filters are supported */ -#define E1000_FLEXIBLE_FILTER_COUNT_MAX 4 - -/* Each Flexible Filter is at most 128 (0x80) bytes in length */ -#define E1000_FLEXIBLE_FILTER_SIZE_MAX 128 - -#define E1000_FFLT_SIZE E1000_FLEXIBLE_FILTER_COUNT_MAX -#define E1000_FFMT_SIZE E1000_FLEXIBLE_FILTER_SIZE_MAX -#define E1000_FFVT_SIZE E1000_FLEXIBLE_FILTER_SIZE_MAX - -#define E1000_DISABLE_SERDES_LOOPBACK 0x0400 - -/* Register Set. (82543, 82544) - * - * Registers are defined to be 32 bits and should be accessed as 32 bit values. - * These registers are physically located on the NIC, but are mapped into the - * host memory address space. - * - * RW - register is both readable and writable - * RO - register is read only - * WO - register is write only - * R/clr - register is read only and is cleared when read - * A - register array - */ -#define E1000_CTRL 0x00000 /* Device Control - RW */ -#define E1000_CTRL_DUP 0x00004 /* Device Control Duplicate (Shadow) - RW */ -#define E1000_STATUS 0x00008 /* Device Status - RO */ -#define E1000_EECD 0x00010 /* EEPROM/Flash Control - RW */ -#define E1000_EERD 0x00014 /* EEPROM Read - RW */ -#define E1000_CTRL_EXT 0x00018 /* Extended Device Control - RW */ -#define E1000_FLA 0x0001C /* Flash Access - RW */ -#define E1000_MDIC 0x00020 /* MDI Control - RW */ -#define E1000_SCTL 0x00024 /* SerDes Control - RW */ -#define E1000_FEXTNVM 0x00028 /* Future Extended NVM register */ -#define E1000_FCAL 0x00028 /* Flow Control Address Low - RW */ -#define E1000_FCAH 0x0002C /* Flow Control Address High -RW */ -#define E1000_FCT 0x00030 /* Flow Control Type - RW */ -#define E1000_VET 0x00038 /* VLAN Ether Type - RW */ -#define E1000_ICR 0x000C0 /* Interrupt Cause Read - R/clr */ -#define E1000_ITR 0x000C4 /* Interrupt Throttling Rate - RW */ -#define E1000_ICS 0x000C8 /* Interrupt Cause Set - WO */ -#define E1000_IMS 0x000D0 /* Interrupt Mask Set - RW */ -#define E1000_IMC 0x000D8 /* Interrupt Mask Clear - WO */ -#define E1000_IAM 0x000E0 /* Interrupt Acknowledge Auto Mask */ -#define E1000_RCTL 0x00100 /* RX Control - RW */ -#define E1000_RDTR1 0x02820 /* RX Delay Timer (1) - RW */ -#define E1000_RDBAL1 0x02900 /* RX Descriptor Base Address Low (1) - RW */ -#define E1000_RDBAH1 0x02904 /* RX Descriptor Base Address High (1) - RW */ -#define E1000_RDLEN1 0x02908 /* RX Descriptor Length (1) - RW */ -#define E1000_RDH1 0x02910 /* RX Descriptor Head (1) - RW */ -#define E1000_RDT1 0x02918 /* RX Descriptor Tail (1) - RW */ -#define E1000_FCTTV 0x00170 /* Flow Control Transmit Timer Value - RW */ -#define E1000_TXCW 0x00178 /* TX Configuration Word - RW */ -#define E1000_RXCW 0x00180 /* RX Configuration Word - RO */ -#define E1000_TCTL 0x00400 /* TX Control - RW */ -#define E1000_TCTL_EXT 0x00404 /* Extended TX Control - RW */ -#define E1000_TIPG 0x00410 /* TX Inter-packet gap -RW */ -#define E1000_TBT 0x00448 /* TX Burst Timer - RW */ -#define E1000_AIT 0x00458 /* Adaptive Interframe Spacing Throttle - RW */ -#define E1000_LEDCTL 0x00E00 /* LED Control - RW */ -#define E1000_EXTCNF_CTRL 0x00F00 /* Extended Configuration Control */ -#define E1000_EXTCNF_SIZE 0x00F08 /* Extended Configuration Size */ -#define E1000_PHY_CTRL 0x00F10 /* PHY Control Register in CSR */ -#define FEXTNVM_SW_CONFIG 0x0001 -#define E1000_PBA 0x01000 /* Packet Buffer Allocation - RW */ -#define E1000_PBS 0x01008 /* Packet Buffer Size */ -#define E1000_EEMNGCTL 0x01010 /* MNG EEprom Control */ -#define E1000_FLASH_UPDATES 1000 -#define E1000_EEARBC 0x01024 /* EEPROM Auto Read Bus Control */ -#define E1000_FLASHT 0x01028 /* FLASH Timer Register */ -#define E1000_EEWR 0x0102C /* EEPROM Write Register - RW */ -#define E1000_FLSWCTL 0x01030 /* FLASH control register */ -#define E1000_FLSWDATA 0x01034 /* FLASH data register */ -#define E1000_FLSWCNT 0x01038 /* FLASH Access Counter */ -#define E1000_FLOP 0x0103C /* FLASH Opcode Register */ -#define E1000_ERT 0x02008 /* Early Rx Threshold - RW */ -#define E1000_FCRTL 0x02160 /* Flow Control Receive Threshold Low - RW */ -#define E1000_FCRTH 0x02168 /* Flow Control Receive Threshold High - RW */ -#define E1000_PSRCTL 0x02170 /* Packet Split Receive Control - RW */ -#define E1000_RDBAL 0x02800 /* RX Descriptor Base Address Low - RW */ -#define E1000_RDBAH 0x02804 /* RX Descriptor Base Address High - RW */ -#define E1000_RDLEN 0x02808 /* RX Descriptor Length - RW */ -#define E1000_RDH 0x02810 /* RX Descriptor Head - RW */ -#define E1000_RDT 0x02818 /* RX Descriptor Tail - RW */ -#define E1000_RDTR 0x02820 /* RX Delay Timer - RW */ -#define E1000_RDBAL0 E1000_RDBAL /* RX Desc Base Address Low (0) - RW */ -#define E1000_RDBAH0 E1000_RDBAH /* RX Desc Base Address High (0) - RW */ -#define E1000_RDLEN0 E1000_RDLEN /* RX Desc Length (0) - RW */ -#define E1000_RDH0 E1000_RDH /* RX Desc Head (0) - RW */ -#define E1000_RDT0 E1000_RDT /* RX Desc Tail (0) - RW */ -#define E1000_RDTR0 E1000_RDTR /* RX Delay Timer (0) - RW */ -#define E1000_RXDCTL 0x02828 /* RX Descriptor Control queue 0 - RW */ -#define E1000_RXDCTL1 0x02928 /* RX Descriptor Control queue 1 - RW */ -#define E1000_RADV 0x0282C /* RX Interrupt Absolute Delay Timer - RW */ -#define E1000_RSRPD 0x02C00 /* RX Small Packet Detect - RW */ -#define E1000_RAID 0x02C08 /* Receive Ack Interrupt Delay - RW */ -#define E1000_TXDMAC 0x03000 /* TX DMA Control - RW */ -#define E1000_KABGTXD 0x03004 /* AFE Band Gap Transmit Ref Data */ -#define E1000_TDFH 0x03410 /* TX Data FIFO Head - RW */ -#define E1000_TDFT 0x03418 /* TX Data FIFO Tail - RW */ -#define E1000_TDFHS 0x03420 /* TX Data FIFO Head Saved - RW */ -#define E1000_TDFTS 0x03428 /* TX Data FIFO Tail Saved - RW */ -#define E1000_TDFPC 0x03430 /* TX Data FIFO Packet Count - RW */ -#define E1000_TDBAL 0x03800 /* TX Descriptor Base Address Low - RW */ -#define E1000_TDBAH 0x03804 /* TX Descriptor Base Address High - RW */ -#define E1000_TDLEN 0x03808 /* TX Descriptor Length - RW */ -#define E1000_TDH 0x03810 /* TX Descriptor Head - RW */ -#define E1000_TDT 0x03818 /* TX Descripotr Tail - RW */ -#define E1000_TIDV 0x03820 /* TX Interrupt Delay Value - RW */ -#define E1000_TXDCTL 0x03828 /* TX Descriptor Control - RW */ -#define E1000_TADV 0x0382C /* TX Interrupt Absolute Delay Val - RW */ -#define E1000_TSPMT 0x03830 /* TCP Segmentation PAD & Min Threshold - RW */ -#define E1000_TARC0 0x03840 /* TX Arbitration Count (0) */ -#define E1000_TDBAL1 0x03900 /* TX Desc Base Address Low (1) - RW */ -#define E1000_TDBAH1 0x03904 /* TX Desc Base Address High (1) - RW */ -#define E1000_TDLEN1 0x03908 /* TX Desc Length (1) - RW */ -#define E1000_TDH1 0x03910 /* TX Desc Head (1) - RW */ -#define E1000_TDT1 0x03918 /* TX Desc Tail (1) - RW */ -#define E1000_TXDCTL1 0x03928 /* TX Descriptor Control (1) - RW */ -#define E1000_TARC1 0x03940 /* TX Arbitration Count (1) */ -#define E1000_CRCERRS 0x04000 /* CRC Error Count - R/clr */ -#define E1000_ALGNERRC 0x04004 /* Alignment Error Count - R/clr */ -#define E1000_SYMERRS 0x04008 /* Symbol Error Count - R/clr */ -#define E1000_RXERRC 0x0400C /* Receive Error Count - R/clr */ -#define E1000_MPC 0x04010 /* Missed Packet Count - R/clr */ -#define E1000_SCC 0x04014 /* Single Collision Count - R/clr */ -#define E1000_ECOL 0x04018 /* Excessive Collision Count - R/clr */ -#define E1000_MCC 0x0401C /* Multiple Collision Count - R/clr */ -#define E1000_LATECOL 0x04020 /* Late Collision Count - R/clr */ -#define E1000_COLC 0x04028 /* Collision Count - R/clr */ -#define E1000_DC 0x04030 /* Defer Count - R/clr */ -#define E1000_TNCRS 0x04034 /* TX-No CRS - R/clr */ -#define E1000_SEC 0x04038 /* Sequence Error Count - R/clr */ -#define E1000_CEXTERR 0x0403C /* Carrier Extension Error Count - R/clr */ -#define E1000_RLEC 0x04040 /* Receive Length Error Count - R/clr */ -#define E1000_XONRXC 0x04048 /* XON RX Count - R/clr */ -#define E1000_XONTXC 0x0404C /* XON TX Count - R/clr */ -#define E1000_XOFFRXC 0x04050 /* XOFF RX Count - R/clr */ -#define E1000_XOFFTXC 0x04054 /* XOFF TX Count - R/clr */ -#define E1000_FCRUC 0x04058 /* Flow Control RX Unsupported Count- R/clr */ -#define E1000_PRC64 0x0405C /* Packets RX (64 bytes) - R/clr */ -#define E1000_PRC127 0x04060 /* Packets RX (65-127 bytes) - R/clr */ -#define E1000_PRC255 0x04064 /* Packets RX (128-255 bytes) - R/clr */ -#define E1000_PRC511 0x04068 /* Packets RX (255-511 bytes) - R/clr */ -#define E1000_PRC1023 0x0406C /* Packets RX (512-1023 bytes) - R/clr */ -#define E1000_PRC1522 0x04070 /* Packets RX (1024-1522 bytes) - R/clr */ -#define E1000_GPRC 0x04074 /* Good Packets RX Count - R/clr */ -#define E1000_BPRC 0x04078 /* Broadcast Packets RX Count - R/clr */ -#define E1000_MPRC 0x0407C /* Multicast Packets RX Count - R/clr */ -#define E1000_GPTC 0x04080 /* Good Packets TX Count - R/clr */ -#define E1000_GORCL 0x04088 /* Good Octets RX Count Low - R/clr */ -#define E1000_GORCH 0x0408C /* Good Octets RX Count High - R/clr */ -#define E1000_GOTCL 0x04090 /* Good Octets TX Count Low - R/clr */ -#define E1000_GOTCH 0x04094 /* Good Octets TX Count High - R/clr */ -#define E1000_RNBC 0x040A0 /* RX No Buffers Count - R/clr */ -#define E1000_RUC 0x040A4 /* RX Undersize Count - R/clr */ -#define E1000_RFC 0x040A8 /* RX Fragment Count - R/clr */ -#define E1000_ROC 0x040AC /* RX Oversize Count - R/clr */ -#define E1000_RJC 0x040B0 /* RX Jabber Count - R/clr */ -#define E1000_MGTPRC 0x040B4 /* Management Packets RX Count - R/clr */ -#define E1000_MGTPDC 0x040B8 /* Management Packets Dropped Count - R/clr */ -#define E1000_MGTPTC 0x040BC /* Management Packets TX Count - R/clr */ -#define E1000_TORL 0x040C0 /* Total Octets RX Low - R/clr */ -#define E1000_TORH 0x040C4 /* Total Octets RX High - R/clr */ -#define E1000_TOTL 0x040C8 /* Total Octets TX Low - R/clr */ -#define E1000_TOTH 0x040CC /* Total Octets TX High - R/clr */ -#define E1000_TPR 0x040D0 /* Total Packets RX - R/clr */ -#define E1000_TPT 0x040D4 /* Total Packets TX - R/clr */ -#define E1000_PTC64 0x040D8 /* Packets TX (64 bytes) - R/clr */ -#define E1000_PTC127 0x040DC /* Packets TX (65-127 bytes) - R/clr */ -#define E1000_PTC255 0x040E0 /* Packets TX (128-255 bytes) - R/clr */ -#define E1000_PTC511 0x040E4 /* Packets TX (256-511 bytes) - R/clr */ -#define E1000_PTC1023 0x040E8 /* Packets TX (512-1023 bytes) - R/clr */ -#define E1000_PTC1522 0x040EC /* Packets TX (1024-1522 Bytes) - R/clr */ -#define E1000_MPTC 0x040F0 /* Multicast Packets TX Count - R/clr */ -#define E1000_BPTC 0x040F4 /* Broadcast Packets TX Count - R/clr */ -#define E1000_TSCTC 0x040F8 /* TCP Segmentation Context TX - R/clr */ -#define E1000_TSCTFC 0x040FC /* TCP Segmentation Context TX Fail - R/clr */ -#define E1000_IAC 0x04100 /* Interrupt Assertion Count */ -#define E1000_ICRXPTC 0x04104 /* Interrupt Cause Rx Packet Timer Expire Count */ -#define E1000_ICRXATC 0x04108 /* Interrupt Cause Rx Absolute Timer Expire Count */ -#define E1000_ICTXPTC 0x0410C /* Interrupt Cause Tx Packet Timer Expire Count */ -#define E1000_ICTXATC 0x04110 /* Interrupt Cause Tx Absolute Timer Expire Count */ -#define E1000_ICTXQEC 0x04118 /* Interrupt Cause Tx Queue Empty Count */ -#define E1000_ICTXQMTC 0x0411C /* Interrupt Cause Tx Queue Minimum Threshold Count */ -#define E1000_ICRXDMTC 0x04120 /* Interrupt Cause Rx Descriptor Minimum Threshold Count */ -#define E1000_ICRXOC 0x04124 /* Interrupt Cause Receiver Overrun Count */ -#define E1000_RXCSUM 0x05000 /* RX Checksum Control - RW */ -#define E1000_RFCTL 0x05008 /* Receive Filter Control*/ -#define E1000_MTA 0x05200 /* Multicast Table Array - RW Array */ -#define E1000_RA 0x05400 /* Receive Address - RW Array */ -#define E1000_VFTA 0x05600 /* VLAN Filter Table Array - RW Array */ -#define E1000_WUC 0x05800 /* Wakeup Control - RW */ -#define E1000_WUFC 0x05808 /* Wakeup Filter Control - RW */ -#define E1000_WUS 0x05810 /* Wakeup Status - RO */ -#define E1000_MANC 0x05820 /* Management Control - RW */ -#define E1000_IPAV 0x05838 /* IP Address Valid - RW */ -#define E1000_IP4AT 0x05840 /* IPv4 Address Table - RW Array */ -#define E1000_IP6AT 0x05880 /* IPv6 Address Table - RW Array */ -#define E1000_WUPL 0x05900 /* Wakeup Packet Length - RW */ -#define E1000_WUPM 0x05A00 /* Wakeup Packet Memory - RO A */ -#define E1000_FFLT 0x05F00 /* Flexible Filter Length Table - RW Array */ -#define E1000_HOST_IF 0x08800 /* Host Interface */ -#define E1000_FFMT 0x09000 /* Flexible Filter Mask Table - RW Array */ -#define E1000_FFVT 0x09800 /* Flexible Filter Value Table - RW Array */ - -#define E1000_KUMCTRLSTA 0x00034 /* MAC-PHY interface - RW */ -#define E1000_MDPHYA 0x0003C /* PHY address - RW */ -#define E1000_MANC2H 0x05860 /* Managment Control To Host - RW */ -#define E1000_SW_FW_SYNC 0x05B5C /* Software-Firmware Synchronization - RW */ - -#define E1000_GCR 0x05B00 /* PCI-Ex Control */ -#define E1000_GSCL_1 0x05B10 /* PCI-Ex Statistic Control #1 */ -#define E1000_GSCL_2 0x05B14 /* PCI-Ex Statistic Control #2 */ -#define E1000_GSCL_3 0x05B18 /* PCI-Ex Statistic Control #3 */ -#define E1000_GSCL_4 0x05B1C /* PCI-Ex Statistic Control #4 */ -#define E1000_FACTPS 0x05B30 /* Function Active and Power State to MNG */ -#define E1000_SWSM 0x05B50 /* SW Semaphore */ -#define E1000_FWSM 0x05B54 /* FW Semaphore */ -#define E1000_FFLT_DBG 0x05F04 /* Debug Register */ -#define E1000_HICR 0x08F00 /* Host Inteface Control */ - -/* RSS registers */ -#define E1000_CPUVEC 0x02C10 /* CPU Vector Register - RW */ -#define E1000_MRQC 0x05818 /* Multiple Receive Control - RW */ -#define E1000_RETA 0x05C00 /* Redirection Table - RW Array */ -#define E1000_RSSRK 0x05C80 /* RSS Random Key - RW Array */ -#define E1000_RSSIM 0x05864 /* RSS Interrupt Mask */ -#define E1000_RSSIR 0x05868 /* RSS Interrupt Request */ -/* Register Set (82542) - * - * Some of the 82542 registers are located at different offsets than they are - * in more current versions of the 8254x. Despite the difference in location, - * the registers function in the same manner. - */ -#define E1000_82542_CTRL E1000_CTRL -#define E1000_82542_CTRL_DUP E1000_CTRL_DUP -#define E1000_82542_STATUS E1000_STATUS -#define E1000_82542_EECD E1000_EECD -#define E1000_82542_EERD E1000_EERD -#define E1000_82542_CTRL_EXT E1000_CTRL_EXT -#define E1000_82542_FLA E1000_FLA -#define E1000_82542_MDIC E1000_MDIC -#define E1000_82542_SCTL E1000_SCTL -#define E1000_82542_FEXTNVM E1000_FEXTNVM -#define E1000_82542_FCAL E1000_FCAL -#define E1000_82542_FCAH E1000_FCAH -#define E1000_82542_FCT E1000_FCT -#define E1000_82542_VET E1000_VET -#define E1000_82542_RA 0x00040 -#define E1000_82542_ICR E1000_ICR -#define E1000_82542_ITR E1000_ITR -#define E1000_82542_ICS E1000_ICS -#define E1000_82542_IMS E1000_IMS -#define E1000_82542_IMC E1000_IMC -#define E1000_82542_RCTL E1000_RCTL -#define E1000_82542_RDTR 0x00108 -#define E1000_82542_RDBAL 0x00110 -#define E1000_82542_RDBAH 0x00114 -#define E1000_82542_RDLEN 0x00118 -#define E1000_82542_RDH 0x00120 -#define E1000_82542_RDT 0x00128 -#define E1000_82542_RDTR0 E1000_82542_RDTR -#define E1000_82542_RDBAL0 E1000_82542_RDBAL -#define E1000_82542_RDBAH0 E1000_82542_RDBAH -#define E1000_82542_RDLEN0 E1000_82542_RDLEN -#define E1000_82542_RDH0 E1000_82542_RDH -#define E1000_82542_RDT0 E1000_82542_RDT -#define E1000_82542_SRRCTL(_n) (0x280C + ((_n) << 8)) /* Split and Replication - * RX Control - RW */ -#define E1000_82542_DCA_RXCTRL(_n) (0x02814 + ((_n) << 8)) -#define E1000_82542_RDBAH3 0x02B04 /* RX Desc Base High Queue 3 - RW */ -#define E1000_82542_RDBAL3 0x02B00 /* RX Desc Low Queue 3 - RW */ -#define E1000_82542_RDLEN3 0x02B08 /* RX Desc Length Queue 3 - RW */ -#define E1000_82542_RDH3 0x02B10 /* RX Desc Head Queue 3 - RW */ -#define E1000_82542_RDT3 0x02B18 /* RX Desc Tail Queue 3 - RW */ -#define E1000_82542_RDBAL2 0x02A00 /* RX Desc Base Low Queue 2 - RW */ -#define E1000_82542_RDBAH2 0x02A04 /* RX Desc Base High Queue 2 - RW */ -#define E1000_82542_RDLEN2 0x02A08 /* RX Desc Length Queue 2 - RW */ -#define E1000_82542_RDH2 0x02A10 /* RX Desc Head Queue 2 - RW */ -#define E1000_82542_RDT2 0x02A18 /* RX Desc Tail Queue 2 - RW */ -#define E1000_82542_RDTR1 0x00130 -#define E1000_82542_RDBAL1 0x00138 -#define E1000_82542_RDBAH1 0x0013C -#define E1000_82542_RDLEN1 0x00140 -#define E1000_82542_RDH1 0x00148 -#define E1000_82542_RDT1 0x00150 -#define E1000_82542_FCRTH 0x00160 -#define E1000_82542_FCRTL 0x00168 -#define E1000_82542_FCTTV E1000_FCTTV -#define E1000_82542_TXCW E1000_TXCW -#define E1000_82542_RXCW E1000_RXCW -#define E1000_82542_MTA 0x00200 -#define E1000_82542_TCTL E1000_TCTL -#define E1000_82542_TCTL_EXT E1000_TCTL_EXT -#define E1000_82542_TIPG E1000_TIPG -#define E1000_82542_TDBAL 0x00420 -#define E1000_82542_TDBAH 0x00424 -#define E1000_82542_TDLEN 0x00428 -#define E1000_82542_TDH 0x00430 -#define E1000_82542_TDT 0x00438 -#define E1000_82542_TIDV 0x00440 -#define E1000_82542_TBT E1000_TBT -#define E1000_82542_AIT E1000_AIT -#define E1000_82542_VFTA 0x00600 -#define E1000_82542_LEDCTL E1000_LEDCTL -#define E1000_82542_PBA E1000_PBA -#define E1000_82542_PBS E1000_PBS -#define E1000_82542_EEMNGCTL E1000_EEMNGCTL -#define E1000_82542_EEARBC E1000_EEARBC -#define E1000_82542_FLASHT E1000_FLASHT -#define E1000_82542_EEWR E1000_EEWR -#define E1000_82542_FLSWCTL E1000_FLSWCTL -#define E1000_82542_FLSWDATA E1000_FLSWDATA -#define E1000_82542_FLSWCNT E1000_FLSWCNT -#define E1000_82542_FLOP E1000_FLOP -#define E1000_82542_EXTCNF_CTRL E1000_EXTCNF_CTRL -#define E1000_82542_EXTCNF_SIZE E1000_EXTCNF_SIZE -#define E1000_82542_PHY_CTRL E1000_PHY_CTRL -#define E1000_82542_ERT E1000_ERT -#define E1000_82542_RXDCTL E1000_RXDCTL -#define E1000_82542_RXDCTL1 E1000_RXDCTL1 -#define E1000_82542_RADV E1000_RADV -#define E1000_82542_RSRPD E1000_RSRPD -#define E1000_82542_TXDMAC E1000_TXDMAC -#define E1000_82542_KABGTXD E1000_KABGTXD -#define E1000_82542_TDFHS E1000_TDFHS -#define E1000_82542_TDFTS E1000_TDFTS -#define E1000_82542_TDFPC E1000_TDFPC -#define E1000_82542_TXDCTL E1000_TXDCTL -#define E1000_82542_TADV E1000_TADV -#define E1000_82542_TSPMT E1000_TSPMT -#define E1000_82542_CRCERRS E1000_CRCERRS -#define E1000_82542_ALGNERRC E1000_ALGNERRC -#define E1000_82542_SYMERRS E1000_SYMERRS -#define E1000_82542_RXERRC E1000_RXERRC -#define E1000_82542_MPC E1000_MPC -#define E1000_82542_SCC E1000_SCC -#define E1000_82542_ECOL E1000_ECOL -#define E1000_82542_MCC E1000_MCC -#define E1000_82542_LATECOL E1000_LATECOL -#define E1000_82542_COLC E1000_COLC -#define E1000_82542_DC E1000_DC -#define E1000_82542_TNCRS E1000_TNCRS -#define E1000_82542_SEC E1000_SEC -#define E1000_82542_CEXTERR E1000_CEXTERR -#define E1000_82542_RLEC E1000_RLEC -#define E1000_82542_XONRXC E1000_XONRXC -#define E1000_82542_XONTXC E1000_XONTXC -#define E1000_82542_XOFFRXC E1000_XOFFRXC -#define E1000_82542_XOFFTXC E1000_XOFFTXC -#define E1000_82542_FCRUC E1000_FCRUC -#define E1000_82542_PRC64 E1000_PRC64 -#define E1000_82542_PRC127 E1000_PRC127 -#define E1000_82542_PRC255 E1000_PRC255 -#define E1000_82542_PRC511 E1000_PRC511 -#define E1000_82542_PRC1023 E1000_PRC1023 -#define E1000_82542_PRC1522 E1000_PRC1522 -#define E1000_82542_GPRC E1000_GPRC -#define E1000_82542_BPRC E1000_BPRC -#define E1000_82542_MPRC E1000_MPRC -#define E1000_82542_GPTC E1000_GPTC -#define E1000_82542_GORCL E1000_GORCL -#define E1000_82542_GORCH E1000_GORCH -#define E1000_82542_GOTCL E1000_GOTCL -#define E1000_82542_GOTCH E1000_GOTCH -#define E1000_82542_RNBC E1000_RNBC -#define E1000_82542_RUC E1000_RUC -#define E1000_82542_RFC E1000_RFC -#define E1000_82542_ROC E1000_ROC -#define E1000_82542_RJC E1000_RJC -#define E1000_82542_MGTPRC E1000_MGTPRC -#define E1000_82542_MGTPDC E1000_MGTPDC -#define E1000_82542_MGTPTC E1000_MGTPTC -#define E1000_82542_TORL E1000_TORL -#define E1000_82542_TORH E1000_TORH -#define E1000_82542_TOTL E1000_TOTL -#define E1000_82542_TOTH E1000_TOTH -#define E1000_82542_TPR E1000_TPR -#define E1000_82542_TPT E1000_TPT -#define E1000_82542_PTC64 E1000_PTC64 -#define E1000_82542_PTC127 E1000_PTC127 -#define E1000_82542_PTC255 E1000_PTC255 -#define E1000_82542_PTC511 E1000_PTC511 -#define E1000_82542_PTC1023 E1000_PTC1023 -#define E1000_82542_PTC1522 E1000_PTC1522 -#define E1000_82542_MPTC E1000_MPTC -#define E1000_82542_BPTC E1000_BPTC -#define E1000_82542_TSCTC E1000_TSCTC -#define E1000_82542_TSCTFC E1000_TSCTFC -#define E1000_82542_RXCSUM E1000_RXCSUM -#define E1000_82542_WUC E1000_WUC -#define E1000_82542_WUFC E1000_WUFC -#define E1000_82542_WUS E1000_WUS -#define E1000_82542_MANC E1000_MANC -#define E1000_82542_IPAV E1000_IPAV -#define E1000_82542_IP4AT E1000_IP4AT -#define E1000_82542_IP6AT E1000_IP6AT -#define E1000_82542_WUPL E1000_WUPL -#define E1000_82542_WUPM E1000_WUPM -#define E1000_82542_FFLT E1000_FFLT -#define E1000_82542_TDFH 0x08010 -#define E1000_82542_TDFT 0x08018 -#define E1000_82542_FFMT E1000_FFMT -#define E1000_82542_FFVT E1000_FFVT -#define E1000_82542_HOST_IF E1000_HOST_IF -#define E1000_82542_IAM E1000_IAM -#define E1000_82542_EEMNGCTL E1000_EEMNGCTL -#define E1000_82542_PSRCTL E1000_PSRCTL -#define E1000_82542_RAID E1000_RAID -#define E1000_82542_TARC0 E1000_TARC0 -#define E1000_82542_TDBAL1 E1000_TDBAL1 -#define E1000_82542_TDBAH1 E1000_TDBAH1 -#define E1000_82542_TDLEN1 E1000_TDLEN1 -#define E1000_82542_TDH1 E1000_TDH1 -#define E1000_82542_TDT1 E1000_TDT1 -#define E1000_82542_TXDCTL1 E1000_TXDCTL1 -#define E1000_82542_TARC1 E1000_TARC1 -#define E1000_82542_RFCTL E1000_RFCTL -#define E1000_82542_GCR E1000_GCR -#define E1000_82542_GSCL_1 E1000_GSCL_1 -#define E1000_82542_GSCL_2 E1000_GSCL_2 -#define E1000_82542_GSCL_3 E1000_GSCL_3 -#define E1000_82542_GSCL_4 E1000_GSCL_4 -#define E1000_82542_FACTPS E1000_FACTPS -#define E1000_82542_SWSM E1000_SWSM -#define E1000_82542_FWSM E1000_FWSM -#define E1000_82542_FFLT_DBG E1000_FFLT_DBG -#define E1000_82542_IAC E1000_IAC -#define E1000_82542_ICRXPTC E1000_ICRXPTC -#define E1000_82542_ICRXATC E1000_ICRXATC -#define E1000_82542_ICTXPTC E1000_ICTXPTC -#define E1000_82542_ICTXATC E1000_ICTXATC -#define E1000_82542_ICTXQEC E1000_ICTXQEC -#define E1000_82542_ICTXQMTC E1000_ICTXQMTC -#define E1000_82542_ICRXDMTC E1000_ICRXDMTC -#define E1000_82542_ICRXOC E1000_ICRXOC -#define E1000_82542_HICR E1000_HICR - -#define E1000_82542_CPUVEC E1000_CPUVEC -#define E1000_82542_MRQC E1000_MRQC -#define E1000_82542_RETA E1000_RETA -#define E1000_82542_RSSRK E1000_RSSRK -#define E1000_82542_RSSIM E1000_RSSIM -#define E1000_82542_RSSIR E1000_RSSIR -#define E1000_82542_KUMCTRLSTA E1000_KUMCTRLSTA -#define E1000_82542_SW_FW_SYNC E1000_SW_FW_SYNC - -/* Statistics counters collected by the MAC */ -struct em_hw_stats { - uint64_t crcerrs; - uint64_t algnerrc; - uint64_t symerrs; - uint64_t rxerrc; - uint64_t mpc; - uint64_t scc; - uint64_t ecol; - uint64_t mcc; - uint64_t latecol; - uint64_t colc; - uint64_t dc; - uint64_t tncrs; - uint64_t sec; - uint64_t cexterr; - uint64_t rlec; - uint64_t xonrxc; - uint64_t xontxc; - uint64_t xoffrxc; - uint64_t xofftxc; - uint64_t fcruc; - uint64_t prc64; - uint64_t prc127; - uint64_t prc255; - uint64_t prc511; - uint64_t prc1023; - uint64_t prc1522; - uint64_t gprc; - uint64_t bprc; - uint64_t mprc; - uint64_t gptc; - uint64_t gorcl; - uint64_t gorch; - uint64_t gotcl; - uint64_t gotch; - uint64_t rnbc; - uint64_t ruc; - uint64_t rfc; - uint64_t roc; - uint64_t rjc; - uint64_t mgprc; - uint64_t mgpdc; - uint64_t mgptc; - uint64_t torl; - uint64_t torh; - uint64_t totl; - uint64_t toth; - uint64_t tpr; - uint64_t tpt; - uint64_t ptc64; - uint64_t ptc127; - uint64_t ptc255; - uint64_t ptc511; - uint64_t ptc1023; - uint64_t ptc1522; - uint64_t mptc; - uint64_t bptc; - uint64_t tsctc; - uint64_t tsctfc; - uint64_t iac; - uint64_t icrxptc; - uint64_t icrxatc; - uint64_t ictxptc; - uint64_t ictxatc; - uint64_t ictxqec; - uint64_t ictxqmtc; - uint64_t icrxdmtc; - uint64_t icrxoc; -}; - -/* Structure containing variables used by the shared code (em_hw.c) */ -struct em_hw { - uint8_t *hw_addr; - uint8_t *flash_address; - em_mac_type mac_type; - em_phy_type phy_type; - uint32_t phy_init_script; - em_media_type media_type; - void *back; - struct em_shadow_ram *eeprom_shadow_ram; - uint32_t flash_bank_size; - uint32_t flash_base_addr; - uint32_t fc; - em_bus_speed bus_speed; - em_bus_width bus_width; - em_bus_type bus_type; - struct em_eeprom_info eeprom; - em_ms_type master_slave; - em_ms_type original_master_slave; - em_ffe_config ffe_config_state; - uint32_t asf_firmware_present; - uint32_t eeprom_semaphore_present; - uint32_t swfw_sync_present; - uint32_t swfwhw_semaphore_present; - - unsigned long io_base; - uint32_t phy_id; - uint32_t phy_revision; - uint32_t phy_addr; - uint32_t original_fc; - uint32_t txcw; - uint32_t autoneg_failed; - uint32_t max_frame_size; - uint32_t min_frame_size; - uint32_t mc_filter_type; - uint32_t num_mc_addrs; - uint32_t collision_delta; - uint32_t tx_packet_delta; - uint32_t ledctl_default; - uint32_t ledctl_mode1; - uint32_t ledctl_mode2; - boolean_t tx_pkt_filtering; - struct em_host_mng_dhcp_cookie mng_cookie; - uint16_t phy_spd_default; - uint16_t autoneg_advertised; - uint16_t pci_cmd_word; - uint16_t fc_high_water; - uint16_t fc_low_water; - uint16_t fc_pause_time; - uint16_t current_ifs_val; - uint16_t ifs_min_val; - uint16_t ifs_max_val; - uint16_t ifs_step_size; - uint16_t ifs_ratio; - uint16_t device_id; - uint16_t vendor_id; - uint16_t subsystem_id; - uint16_t subsystem_vendor_id; - uint8_t revision_id; - uint8_t autoneg; - uint8_t mdix; - uint8_t forced_speed_duplex; - uint8_t wait_autoneg_complete; - uint8_t dma_fairness; - uint8_t mac_addr[NODE_ADDRESS_SIZE]; - uint8_t perm_mac_addr[NODE_ADDRESS_SIZE]; - boolean_t disable_polarity_correction; - boolean_t speed_downgraded; - em_smart_speed smart_speed; - em_dsp_config dsp_config_state; - boolean_t get_link_status; - boolean_t serdes_link_down; - boolean_t tbi_compatibility_en; - boolean_t tbi_compatibility_on; - boolean_t laa_is_present; - boolean_t phy_reset_disable; - boolean_t initialize_hw_bits_disable; - boolean_t fc_send_xon; - boolean_t fc_strict_ieee; - boolean_t report_tx_early; - boolean_t adaptive_ifs; - boolean_t ifs_params_forced; - boolean_t in_ifs_mode; - boolean_t mng_reg_access_disabled; - boolean_t leave_av_bit_off; - boolean_t kmrn_lock_loss_workaround_disabled; -}; - - -#define E1000_EEPROM_SWDPIN0 0x0001 /* SWDPIN 0 EEPROM Value */ -#define E1000_EEPROM_LED_LOGIC 0x0020 /* Led Logic Word */ -#define E1000_EEPROM_RW_REG_DATA 16 /* Offset to data in EEPROM read/write registers */ -#define E1000_EEPROM_RW_REG_DONE 2 /* Offset to READ/WRITE done bit */ -#define E1000_EEPROM_RW_REG_START 1 /* First bit for telling part to start operation */ -#define E1000_EEPROM_RW_ADDR_SHIFT 2 /* Shift to the address bits */ -#define E1000_EEPROM_POLL_WRITE 1 /* Flag for polling for write complete */ -#define E1000_EEPROM_POLL_READ 0 /* Flag for polling for read complete */ -/* Register Bit Masks */ -/* Device Control */ -#define E1000_CTRL_FD 0x00000001 /* Full duplex.0=half; 1=full */ -#define E1000_CTRL_BEM 0x00000002 /* Endian Mode.0=little,1=big */ -#define E1000_CTRL_PRIOR 0x00000004 /* Priority on PCI. 0=rx,1=fair */ -#define E1000_CTRL_GIO_MASTER_DISABLE 0x00000004 /*Blocks new Master requests */ -#define E1000_CTRL_LRST 0x00000008 /* Link reset. 0=normal,1=reset */ -#define E1000_CTRL_TME 0x00000010 /* Test mode. 0=normal,1=test */ -#define E1000_CTRL_SLE 0x00000020 /* Serial Link on 0=dis,1=en */ -#define E1000_CTRL_ASDE 0x00000020 /* Auto-speed detect enable */ -#define E1000_CTRL_SLU 0x00000040 /* Set link up (Force Link) */ -#define E1000_CTRL_ILOS 0x00000080 /* Invert Loss-Of Signal */ -#define E1000_CTRL_SPD_SEL 0x00000300 /* Speed Select Mask */ -#define E1000_CTRL_SPD_10 0x00000000 /* Force 10Mb */ -#define E1000_CTRL_SPD_100 0x00000100 /* Force 100Mb */ -#define E1000_CTRL_SPD_1000 0x00000200 /* Force 1Gb */ -#define E1000_CTRL_BEM32 0x00000400 /* Big Endian 32 mode */ -#define E1000_CTRL_FRCSPD 0x00000800 /* Force Speed */ -#define E1000_CTRL_FRCDPX 0x00001000 /* Force Duplex */ -#define E1000_CTRL_D_UD_EN 0x00002000 /* Dock/Undock enable */ -#define E1000_CTRL_D_UD_POLARITY 0x00004000 /* Defined polarity of Dock/Undock indication in SDP[0] */ -#define E1000_CTRL_FORCE_PHY_RESET 0x00008000 /* Reset both PHY ports, through PHYRST_N pin */ -#define E1000_CTRL_EXT_LINK_EN 0x00010000 /* enable link status from external LINK_0 and LINK_1 pins */ -#define E1000_CTRL_SWDPIN0 0x00040000 /* SWDPIN 0 value */ -#define E1000_CTRL_SWDPIN1 0x00080000 /* SWDPIN 1 value */ -#define E1000_CTRL_SWDPIN2 0x00100000 /* SWDPIN 2 value */ -#define E1000_CTRL_SWDPIN3 0x00200000 /* SWDPIN 3 value */ -#define E1000_CTRL_SWDPIO0 0x00400000 /* SWDPIN 0 Input or output */ -#define E1000_CTRL_SWDPIO1 0x00800000 /* SWDPIN 1 input or output */ -#define E1000_CTRL_SWDPIO2 0x01000000 /* SWDPIN 2 input or output */ -#define E1000_CTRL_SWDPIO3 0x02000000 /* SWDPIN 3 input or output */ -#define E1000_CTRL_RST 0x04000000 /* Global reset */ -#define E1000_CTRL_RFCE 0x08000000 /* Receive Flow Control enable */ -#define E1000_CTRL_TFCE 0x10000000 /* Transmit flow control enable */ -#define E1000_CTRL_RTE 0x20000000 /* Routing tag enable */ -#define E1000_CTRL_VME 0x40000000 /* IEEE VLAN mode enable */ -#define E1000_CTRL_PHY_RST 0x80000000 /* PHY Reset */ -#define E1000_CTRL_SW2FW_INT 0x02000000 /* Initiate an interrupt to manageability engine */ -/* Device Status */ -#define E1000_STATUS_FD 0x00000001 /* Full duplex.0=half,1=full */ -#define E1000_STATUS_LU 0x00000002 /* Link up.0=no,1=link */ -#define E1000_STATUS_FUNC_MASK 0x0000000C /* PCI Function Mask */ -#define E1000_STATUS_FUNC_SHIFT 2 -#define E1000_STATUS_FUNC_0 0x00000000 /* Function 0 */ -#define E1000_STATUS_FUNC_1 0x00000004 /* Function 1 */ -#define E1000_STATUS_TXOFF 0x00000010 /* transmission paused */ -#define E1000_STATUS_TBIMODE 0x00000020 /* TBI mode */ -#define E1000_STATUS_SPEED_MASK 0x000000C0 -#define E1000_STATUS_SPEED_10 0x00000000 /* Speed 10Mb/s */ -#define E1000_STATUS_SPEED_100 0x00000040 /* Speed 100Mb/s */ -#define E1000_STATUS_SPEED_1000 0x00000080 /* Speed 1000Mb/s */ -#define E1000_STATUS_LAN_INIT_DONE 0x00000200 /* Lan Init Completion - by EEPROM/Flash */ -#define E1000_STATUS_ASDV 0x00000300 /* Auto speed detect value */ -#define E1000_STATUS_DOCK_CI 0x00000800 /* Change in Dock/Undock state. Clear on write '0'. */ -#define E1000_STATUS_GIO_MASTER_ENABLE 0x00080000 /* Status of Master requests. */ -#define E1000_STATUS_MTXCKOK 0x00000400 /* MTX clock running OK */ -#define E1000_STATUS_PCI66 0x00000800 /* In 66Mhz slot */ -#define E1000_STATUS_BUS64 0x00001000 /* In 64 bit slot */ -#define E1000_STATUS_PCIX_MODE 0x00002000 /* PCI-X mode */ -#define E1000_STATUS_PCIX_SPEED 0x0000C000 /* PCI-X bus speed */ -#define E1000_STATUS_BMC_SKU_0 0x00100000 /* BMC USB redirect disabled */ -#define E1000_STATUS_BMC_SKU_1 0x00200000 /* BMC SRAM disabled */ -#define E1000_STATUS_BMC_SKU_2 0x00400000 /* BMC SDRAM disabled */ -#define E1000_STATUS_BMC_CRYPTO 0x00800000 /* BMC crypto disabled */ -#define E1000_STATUS_BMC_LITE 0x01000000 /* BMC external code execution disabled */ -#define E1000_STATUS_RGMII_ENABLE 0x02000000 /* RGMII disabled */ -#define E1000_STATUS_FUSE_8 0x04000000 -#define E1000_STATUS_FUSE_9 0x08000000 -#define E1000_STATUS_SERDES0_DIS 0x10000000 /* SERDES disabled on port 0 */ -#define E1000_STATUS_SERDES1_DIS 0x20000000 /* SERDES disabled on port 1 */ - -/* Constants used to intrepret the masked PCI-X bus speed. */ -#define E1000_STATUS_PCIX_SPEED_66 0x00000000 /* PCI-X bus speed 50-66 MHz */ -#define E1000_STATUS_PCIX_SPEED_100 0x00004000 /* PCI-X bus speed 66-100 MHz */ -#define E1000_STATUS_PCIX_SPEED_133 0x00008000 /* PCI-X bus speed 100-133 MHz */ - -/* EEPROM/Flash Control */ -#define E1000_EECD_SK 0x00000001 /* EEPROM Clock */ -#define E1000_EECD_CS 0x00000002 /* EEPROM Chip Select */ -#define E1000_EECD_DI 0x00000004 /* EEPROM Data In */ -#define E1000_EECD_DO 0x00000008 /* EEPROM Data Out */ -#define E1000_EECD_FWE_MASK 0x00000030 -#define E1000_EECD_FWE_DIS 0x00000010 /* Disable FLASH writes */ -#define E1000_EECD_FWE_EN 0x00000020 /* Enable FLASH writes */ -#define E1000_EECD_FWE_SHIFT 4 -#define E1000_EECD_REQ 0x00000040 /* EEPROM Access Request */ -#define E1000_EECD_GNT 0x00000080 /* EEPROM Access Grant */ -#define E1000_EECD_PRES 0x00000100 /* EEPROM Present */ -#define E1000_EECD_SIZE 0x00000200 /* EEPROM Size (0=64 word 1=256 word) */ -#define E1000_EECD_ADDR_BITS 0x00000400 /* EEPROM Addressing bits based on type - * (0-small, 1-large) */ -#define E1000_EECD_TYPE 0x00002000 /* EEPROM Type (1-SPI, 0-Microwire) */ -#ifndef E1000_EEPROM_GRANT_ATTEMPTS -#define E1000_EEPROM_GRANT_ATTEMPTS 1000 /* EEPROM # attempts to gain grant */ -#endif -#define E1000_EECD_AUTO_RD 0x00000200 /* EEPROM Auto Read done */ -#define E1000_EECD_SIZE_EX_MASK 0x00007800 /* EEprom Size */ -#define E1000_EECD_SIZE_EX_SHIFT 11 -#define E1000_EECD_NVADDS 0x00018000 /* NVM Address Size */ -#define E1000_EECD_SELSHAD 0x00020000 /* Select Shadow RAM */ -#define E1000_EECD_INITSRAM 0x00040000 /* Initialize Shadow RAM */ -#define E1000_EECD_FLUPD 0x00080000 /* Update FLASH */ -#define E1000_EECD_AUPDEN 0x00100000 /* Enable Autonomous FLASH update */ -#define E1000_EECD_SHADV 0x00200000 /* Shadow RAM Data Valid */ -#define E1000_EECD_SEC1VAL 0x00400000 /* Sector One Valid */ -#define E1000_EECD_SECVAL_SHIFT 22 -#define E1000_STM_OPCODE 0xDB00 -#define E1000_HICR_FW_RESET 0xC0 - -#define E1000_SHADOW_RAM_WORDS 2048 -#define E1000_ICH_NVM_SIG_WORD 0x13 -#define E1000_ICH_NVM_SIG_MASK 0xC0 - -/* EEPROM Read */ -#define E1000_EERD_START 0x00000001 /* Start Read */ -#define E1000_EERD_DONE 0x00000010 /* Read Done */ -#define E1000_EERD_ADDR_SHIFT 8 -#define E1000_EERD_ADDR_MASK 0x0000FF00 /* Read Address */ -#define E1000_EERD_DATA_SHIFT 16 -#define E1000_EERD_DATA_MASK 0xFFFF0000 /* Read Data */ - -/* SPI EEPROM Status Register */ -#define EEPROM_STATUS_RDY_SPI 0x01 -#define EEPROM_STATUS_WEN_SPI 0x02 -#define EEPROM_STATUS_BP0_SPI 0x04 -#define EEPROM_STATUS_BP1_SPI 0x08 -#define EEPROM_STATUS_WPEN_SPI 0x80 - -/* Extended Device Control */ -#define E1000_CTRL_EXT_GPI0_EN 0x00000001 /* Maps SDP4 to GPI0 */ -#define E1000_CTRL_EXT_GPI1_EN 0x00000002 /* Maps SDP5 to GPI1 */ -#define E1000_CTRL_EXT_PHYINT_EN E1000_CTRL_EXT_GPI1_EN -#define E1000_CTRL_EXT_GPI2_EN 0x00000004 /* Maps SDP6 to GPI2 */ -#define E1000_CTRL_EXT_GPI3_EN 0x00000008 /* Maps SDP7 to GPI3 */ -#define E1000_CTRL_EXT_SDP4_DATA 0x00000010 /* Value of SW Defineable Pin 4 */ -#define E1000_CTRL_EXT_SDP5_DATA 0x00000020 /* Value of SW Defineable Pin 5 */ -#define E1000_CTRL_EXT_PHY_INT E1000_CTRL_EXT_SDP5_DATA -#define E1000_CTRL_EXT_SDP6_DATA 0x00000040 /* Value of SW Defineable Pin 6 */ -#define E1000_CTRL_EXT_SDP7_DATA 0x00000080 /* Value of SW Defineable Pin 7 */ -#define E1000_CTRL_EXT_SDP4_DIR 0x00000100 /* Direction of SDP4 0=in 1=out */ -#define E1000_CTRL_EXT_SDP5_DIR 0x00000200 /* Direction of SDP5 0=in 1=out */ -#define E1000_CTRL_EXT_SDP6_DIR 0x00000400 /* Direction of SDP6 0=in 1=out */ -#define E1000_CTRL_EXT_SDP7_DIR 0x00000800 /* Direction of SDP7 0=in 1=out */ -#define E1000_CTRL_EXT_ASDCHK 0x00001000 /* Initiate an ASD sequence */ -#define E1000_CTRL_EXT_EE_RST 0x00002000 /* Reinitialize from EEPROM */ -#define E1000_CTRL_EXT_IPS 0x00004000 /* Invert Power State */ -#define E1000_CTRL_EXT_SPD_BYPS 0x00008000 /* Speed Select Bypass */ -#define E1000_CTRL_EXT_RO_DIS 0x00020000 /* Relaxed Ordering disable */ -#define E1000_CTRL_EXT_LINK_MODE_MASK 0x00C00000 -#define E1000_CTRL_EXT_LINK_MODE_GMII 0x00000000 -#define E1000_CTRL_EXT_LINK_MODE_TBI 0x00C00000 -#define E1000_CTRL_EXT_LINK_MODE_KMRN 0x00000000 -#define E1000_CTRL_EXT_LINK_MODE_SERDES 0x00C00000 -#define E1000_CTRL_EXT_LINK_MODE_SGMII 0x00800000 -#define E1000_CTRL_EXT_WR_WMARK_MASK 0x03000000 -#define E1000_CTRL_EXT_WR_WMARK_256 0x00000000 -#define E1000_CTRL_EXT_WR_WMARK_320 0x01000000 -#define E1000_CTRL_EXT_WR_WMARK_384 0x02000000 -#define E1000_CTRL_EXT_WR_WMARK_448 0x03000000 -#define E1000_CTRL_EXT_DRV_LOAD 0x10000000 /* Driver loaded bit for FW */ -#define E1000_CTRL_EXT_IAME 0x08000000 /* Interrupt acknowledge Auto-mask */ -#define E1000_CTRL_EXT_INT_TIMER_CLR 0x20000000 /* Clear Interrupt timers after IMS clear */ -#define E1000_CRTL_EXT_PB_PAREN 0x01000000 /* packet buffer parity error detection enabled */ -#define E1000_CTRL_EXT_DF_PAREN 0x02000000 /* descriptor FIFO parity error detection enable */ -#define E1000_CTRL_EXT_GHOST_PAREN 0x40000000 - -/* MDI Control */ -#define E1000_MDIC_DATA_MASK 0x0000FFFF -#define E1000_MDIC_REG_MASK 0x001F0000 -#define E1000_MDIC_REG_SHIFT 16 -#define E1000_MDIC_PHY_MASK 0x03E00000 -#define E1000_MDIC_PHY_SHIFT 21 -#define E1000_MDIC_OP_WRITE 0x04000000 -#define E1000_MDIC_OP_READ 0x08000000 -#define E1000_MDIC_READY 0x10000000 -#define E1000_MDIC_INT_EN 0x20000000 -#define E1000_MDIC_ERROR 0x40000000 - -#define E1000_KUMCTRLSTA_MASK 0x0000FFFF -#define E1000_KUMCTRLSTA_OFFSET 0x001F0000 -#define E1000_KUMCTRLSTA_OFFSET_SHIFT 16 -#define E1000_KUMCTRLSTA_REN 0x00200000 - -#define E1000_KUMCTRLSTA_OFFSET_FIFO_CTRL 0x00000000 -#define E1000_KUMCTRLSTA_OFFSET_CTRL 0x00000001 -#define E1000_KUMCTRLSTA_OFFSET_INB_CTRL 0x00000002 -#define E1000_KUMCTRLSTA_OFFSET_DIAG 0x00000003 -#define E1000_KUMCTRLSTA_OFFSET_TIMEOUTS 0x00000004 -#define E1000_KUMCTRLSTA_OFFSET_INB_PARAM 0x00000009 -#define E1000_KUMCTRLSTA_OFFSET_HD_CTRL 0x00000010 -#define E1000_KUMCTRLSTA_OFFSET_M2P_SERDES 0x0000001E -#define E1000_KUMCTRLSTA_OFFSET_M2P_MODES 0x0000001F - -/* FIFO Control */ -#define E1000_KUMCTRLSTA_FIFO_CTRL_RX_BYPASS 0x00000008 -#define E1000_KUMCTRLSTA_FIFO_CTRL_TX_BYPASS 0x00000800 - -/* In-Band Control */ -#define E1000_KUMCTRLSTA_INB_CTRL_LINK_STATUS_TX_TIMEOUT_DEFAULT 0x00000500 -#define E1000_KUMCTRLSTA_INB_CTRL_DIS_PADDING 0x00000010 - -/* Half-Duplex Control */ -#define E1000_KUMCTRLSTA_HD_CTRL_10_100_DEFAULT 0x00000004 -#define E1000_KUMCTRLSTA_HD_CTRL_1000_DEFAULT 0x00000000 - -#define E1000_KUMCTRLSTA_OFFSET_K0S_CTRL 0x0000001E - -#define E1000_KUMCTRLSTA_DIAG_FELPBK 0x2000 -#define E1000_KUMCTRLSTA_DIAG_NELPBK 0x1000 - -#define E1000_KUMCTRLSTA_K0S_100_EN 0x2000 -#define E1000_KUMCTRLSTA_K0S_GBE_EN 0x1000 -#define E1000_KUMCTRLSTA_K0S_ENTRY_LATENCY_MASK 0x0003 - -#define E1000_KABGTXD_BGSQLBIAS 0x00050000 - -#define E1000_PHY_CTRL_SPD_EN 0x00000001 -#define E1000_PHY_CTRL_D0A_LPLU 0x00000002 -#define E1000_PHY_CTRL_NOND0A_LPLU 0x00000004 -#define E1000_PHY_CTRL_NOND0A_GBE_DISABLE 0x00000008 -#define E1000_PHY_CTRL_GBE_DISABLE 0x00000040 -#define E1000_PHY_CTRL_B2B_EN 0x00000080 - -/* LED Control */ -#define E1000_LEDCTL_LED0_MODE_MASK 0x0000000F -#define E1000_LEDCTL_LED0_MODE_SHIFT 0 -#define E1000_LEDCTL_LED0_BLINK_RATE 0x0000020 -#define E1000_LEDCTL_LED0_IVRT 0x00000040 -#define E1000_LEDCTL_LED0_BLINK 0x00000080 -#define E1000_LEDCTL_LED1_MODE_MASK 0x00000F00 -#define E1000_LEDCTL_LED1_MODE_SHIFT 8 -#define E1000_LEDCTL_LED1_BLINK_RATE 0x0002000 -#define E1000_LEDCTL_LED1_IVRT 0x00004000 -#define E1000_LEDCTL_LED1_BLINK 0x00008000 -#define E1000_LEDCTL_LED2_MODE_MASK 0x000F0000 -#define E1000_LEDCTL_LED2_MODE_SHIFT 16 -#define E1000_LEDCTL_LED2_BLINK_RATE 0x00200000 -#define E1000_LEDCTL_LED2_IVRT 0x00400000 -#define E1000_LEDCTL_LED2_BLINK 0x00800000 -#define E1000_LEDCTL_LED3_MODE_MASK 0x0F000000 -#define E1000_LEDCTL_LED3_MODE_SHIFT 24 -#define E1000_LEDCTL_LED3_BLINK_RATE 0x20000000 -#define E1000_LEDCTL_LED3_IVRT 0x40000000 -#define E1000_LEDCTL_LED3_BLINK 0x80000000 - -#define E1000_LEDCTL_MODE_LINK_10_1000 0x0 -#define E1000_LEDCTL_MODE_LINK_100_1000 0x1 -#define E1000_LEDCTL_MODE_LINK_UP 0x2 -#define E1000_LEDCTL_MODE_ACTIVITY 0x3 -#define E1000_LEDCTL_MODE_LINK_ACTIVITY 0x4 -#define E1000_LEDCTL_MODE_LINK_10 0x5 -#define E1000_LEDCTL_MODE_LINK_100 0x6 -#define E1000_LEDCTL_MODE_LINK_1000 0x7 -#define E1000_LEDCTL_MODE_PCIX_MODE 0x8 -#define E1000_LEDCTL_MODE_FULL_DUPLEX 0x9 -#define E1000_LEDCTL_MODE_COLLISION 0xA -#define E1000_LEDCTL_MODE_BUS_SPEED 0xB -#define E1000_LEDCTL_MODE_BUS_SIZE 0xC -#define E1000_LEDCTL_MODE_PAUSED 0xD -#define E1000_LEDCTL_MODE_LED_ON 0xE -#define E1000_LEDCTL_MODE_LED_OFF 0xF - -/* Receive Address */ -#define E1000_RAH_AV 0x80000000 /* Receive descriptor valid */ - -/* Interrupt Cause Read */ -#define E1000_ICR_TXDW 0x00000001 /* Transmit desc written back */ -#define E1000_ICR_TXQE 0x00000002 /* Transmit Queue empty */ -#define E1000_ICR_LSC 0x00000004 /* Link Status Change */ -#define E1000_ICR_RXSEQ 0x00000008 /* rx sequence error */ -#define E1000_ICR_RXDMT0 0x00000010 /* rx desc min. threshold (0) */ -#define E1000_ICR_RXO 0x00000040 /* rx overrun */ -#define E1000_ICR_RXT0 0x00000080 /* rx timer intr (ring 0) */ -#define E1000_ICR_MDAC 0x00000200 /* MDIO access complete */ -#define E1000_ICR_RXCFG 0x00000400 /* RX /c/ ordered set */ -#define E1000_ICR_GPI_EN0 0x00000800 /* GP Int 0 */ -#define E1000_ICR_GPI_EN1 0x00001000 /* GP Int 1 */ -#define E1000_ICR_GPI_EN2 0x00002000 /* GP Int 2 */ -#define E1000_ICR_GPI_EN3 0x00004000 /* GP Int 3 */ -#define E1000_ICR_TXD_LOW 0x00008000 -#define E1000_ICR_SRPD 0x00010000 -#define E1000_ICR_ACK 0x00020000 /* Receive Ack frame */ -#define E1000_ICR_MNG 0x00040000 /* Manageability event */ -#define E1000_ICR_DOCK 0x00080000 /* Dock/Undock */ -#define E1000_ICR_INT_ASSERTED 0x80000000 /* If this bit asserted, the driver should claim the interrupt */ -#define E1000_ICR_RXD_FIFO_PAR0 0x00100000 /* queue 0 Rx descriptor FIFO parity error */ -#define E1000_ICR_TXD_FIFO_PAR0 0x00200000 /* queue 0 Tx descriptor FIFO parity error */ -#define E1000_ICR_HOST_ARB_PAR 0x00400000 /* host arb read buffer parity error */ -#define E1000_ICR_PB_PAR 0x00800000 /* packet buffer parity error */ -#define E1000_ICR_RXD_FIFO_PAR1 0x01000000 /* queue 1 Rx descriptor FIFO parity error */ -#define E1000_ICR_TXD_FIFO_PAR1 0x02000000 /* queue 1 Tx descriptor FIFO parity error */ -#define E1000_ICR_ALL_PARITY 0x03F00000 /* all parity error bits */ -#define E1000_ICR_DSW 0x00000020 /* FW changed the status of DISSW bit in the FWSM */ -#define E1000_ICR_PHYINT 0x00001000 /* LAN connected device generates an interrupt */ -#define E1000_ICR_EPRST 0x00100000 /* ME handware reset occurs */ - - -/* Interrupt Cause Set */ -#define E1000_ICS_TXDW E1000_ICR_TXDW /* Transmit desc written back */ -#define E1000_ICS_TXQE E1000_ICR_TXQE /* Transmit Queue empty */ -#define E1000_ICS_LSC E1000_ICR_LSC /* Link Status Change */ -#define E1000_ICS_RXSEQ E1000_ICR_RXSEQ /* rx sequence error */ -#define E1000_ICS_RXDMT0 E1000_ICR_RXDMT0 /* rx desc min. threshold */ -#define E1000_ICS_RXO E1000_ICR_RXO /* rx overrun */ -#define E1000_ICS_RXT0 E1000_ICR_RXT0 /* rx timer intr */ -#define E1000_ICS_MDAC E1000_ICR_MDAC /* MDIO access complete */ -#define E1000_ICS_RXCFG E1000_ICR_RXCFG /* RX /c/ ordered set */ -#define E1000_ICS_GPI_EN0 E1000_ICR_GPI_EN0 /* GP Int 0 */ -#define E1000_ICS_GPI_EN1 E1000_ICR_GPI_EN1 /* GP Int 1 */ -#define E1000_ICS_GPI_EN2 E1000_ICR_GPI_EN2 /* GP Int 2 */ -#define E1000_ICS_GPI_EN3 E1000_ICR_GPI_EN3 /* GP Int 3 */ -#define E1000_ICS_TXD_LOW E1000_ICR_TXD_LOW -#define E1000_ICS_SRPD E1000_ICR_SRPD -#define E1000_ICS_ACK E1000_ICR_ACK /* Receive Ack frame */ -#define E1000_ICS_MNG E1000_ICR_MNG /* Manageability event */ -#define E1000_ICS_DOCK E1000_ICR_DOCK /* Dock/Undock */ -#define E1000_ICS_RXD_FIFO_PAR0 E1000_ICR_RXD_FIFO_PAR0 /* queue 0 Rx descriptor FIFO parity error */ -#define E1000_ICS_TXD_FIFO_PAR0 E1000_ICR_TXD_FIFO_PAR0 /* queue 0 Tx descriptor FIFO parity error */ -#define E1000_ICS_HOST_ARB_PAR E1000_ICR_HOST_ARB_PAR /* host arb read buffer parity error */ -#define E1000_ICS_PB_PAR E1000_ICR_PB_PAR /* packet buffer parity error */ -#define E1000_ICS_RXD_FIFO_PAR1 E1000_ICR_RXD_FIFO_PAR1 /* queue 1 Rx descriptor FIFO parity error */ -#define E1000_ICS_TXD_FIFO_PAR1 E1000_ICR_TXD_FIFO_PAR1 /* queue 1 Tx descriptor FIFO parity error */ -#define E1000_ICS_DSW E1000_ICR_DSW -#define E1000_ICS_PHYINT E1000_ICR_PHYINT -#define E1000_ICS_EPRST E1000_ICR_EPRST - - -/* Interrupt Mask Set */ -#define E1000_IMS_TXDW E1000_ICR_TXDW /* Transmit desc written back */ -#define E1000_IMS_TXQE E1000_ICR_TXQE /* Transmit Queue empty */ -#define E1000_IMS_LSC E1000_ICR_LSC /* Link Status Change */ -#define E1000_IMS_RXSEQ E1000_ICR_RXSEQ /* rx sequence error */ -#define E1000_IMS_RXDMT0 E1000_ICR_RXDMT0 /* rx desc min. threshold */ -#define E1000_IMS_RXO E1000_ICR_RXO /* rx overrun */ -#define E1000_IMS_RXT0 E1000_ICR_RXT0 /* rx timer intr */ -#define E1000_IMS_MDAC E1000_ICR_MDAC /* MDIO access complete */ -#define E1000_IMS_RXCFG E1000_ICR_RXCFG /* RX /c/ ordered set */ -#define E1000_IMS_GPI_EN0 E1000_ICR_GPI_EN0 /* GP Int 0 */ -#define E1000_IMS_GPI_EN1 E1000_ICR_GPI_EN1 /* GP Int 1 */ -#define E1000_IMS_GPI_EN2 E1000_ICR_GPI_EN2 /* GP Int 2 */ -#define E1000_IMS_GPI_EN3 E1000_ICR_GPI_EN3 /* GP Int 3 */ -#define E1000_IMS_TXD_LOW E1000_ICR_TXD_LOW -#define E1000_IMS_SRPD E1000_ICR_SRPD -#define E1000_IMS_ACK E1000_ICR_ACK /* Receive Ack frame */ -#define E1000_IMS_MNG E1000_ICR_MNG /* Manageability event */ -#define E1000_IMS_DOCK E1000_ICR_DOCK /* Dock/Undock */ -#define E1000_IMS_RXD_FIFO_PAR0 E1000_ICR_RXD_FIFO_PAR0 /* queue 0 Rx descriptor FIFO parity error */ -#define E1000_IMS_TXD_FIFO_PAR0 E1000_ICR_TXD_FIFO_PAR0 /* queue 0 Tx descriptor FIFO parity error */ -#define E1000_IMS_HOST_ARB_PAR E1000_ICR_HOST_ARB_PAR /* host arb read buffer parity error */ -#define E1000_IMS_PB_PAR E1000_ICR_PB_PAR /* packet buffer parity error */ -#define E1000_IMS_RXD_FIFO_PAR1 E1000_ICR_RXD_FIFO_PAR1 /* queue 1 Rx descriptor FIFO parity error */ -#define E1000_IMS_TXD_FIFO_PAR1 E1000_ICR_TXD_FIFO_PAR1 /* queue 1 Tx descriptor FIFO parity error */ -#define E1000_IMS_DSW E1000_ICR_DSW -#define E1000_IMS_PHYINT E1000_ICR_PHYINT -#define E1000_IMS_EPRST E1000_ICR_EPRST - - -/* Interrupt Mask Clear */ -#define E1000_IMC_TXDW E1000_ICR_TXDW /* Transmit desc written back */ -#define E1000_IMC_TXQE E1000_ICR_TXQE /* Transmit Queue empty */ -#define E1000_IMC_LSC E1000_ICR_LSC /* Link Status Change */ -#define E1000_IMC_RXSEQ E1000_ICR_RXSEQ /* rx sequence error */ -#define E1000_IMC_RXDMT0 E1000_ICR_RXDMT0 /* rx desc min. threshold */ -#define E1000_IMC_RXO E1000_ICR_RXO /* rx overrun */ -#define E1000_IMC_RXT0 E1000_ICR_RXT0 /* rx timer intr */ -#define E1000_IMC_MDAC E1000_ICR_MDAC /* MDIO access complete */ -#define E1000_IMC_RXCFG E1000_ICR_RXCFG /* RX /c/ ordered set */ -#define E1000_IMC_GPI_EN0 E1000_ICR_GPI_EN0 /* GP Int 0 */ -#define E1000_IMC_GPI_EN1 E1000_ICR_GPI_EN1 /* GP Int 1 */ -#define E1000_IMC_GPI_EN2 E1000_ICR_GPI_EN2 /* GP Int 2 */ -#define E1000_IMC_GPI_EN3 E1000_ICR_GPI_EN3 /* GP Int 3 */ -#define E1000_IMC_TXD_LOW E1000_ICR_TXD_LOW -#define E1000_IMC_SRPD E1000_ICR_SRPD -#define E1000_IMC_ACK E1000_ICR_ACK /* Receive Ack frame */ -#define E1000_IMC_MNG E1000_ICR_MNG /* Manageability event */ -#define E1000_IMC_DOCK E1000_ICR_DOCK /* Dock/Undock */ -#define E1000_IMC_RXD_FIFO_PAR0 E1000_ICR_RXD_FIFO_PAR0 /* queue 0 Rx descriptor FIFO parity error */ -#define E1000_IMC_TXD_FIFO_PAR0 E1000_ICR_TXD_FIFO_PAR0 /* queue 0 Tx descriptor FIFO parity error */ -#define E1000_IMC_HOST_ARB_PAR E1000_ICR_HOST_ARB_PAR /* host arb read buffer parity error */ -#define E1000_IMC_PB_PAR E1000_ICR_PB_PAR /* packet buffer parity error */ -#define E1000_IMC_RXD_FIFO_PAR1 E1000_ICR_RXD_FIFO_PAR1 /* queue 1 Rx descriptor FIFO parity error */ -#define E1000_IMC_TXD_FIFO_PAR1 E1000_ICR_TXD_FIFO_PAR1 /* queue 1 Tx descriptor FIFO parity error */ -#define E1000_IMC_DSW E1000_ICR_DSW -#define E1000_IMC_PHYINT E1000_ICR_PHYINT -#define E1000_IMC_EPRST E1000_ICR_EPRST - - -/* Receive Control */ -#define E1000_RCTL_RST 0x00000001 /* Software reset */ -#define E1000_RCTL_EN 0x00000002 /* enable */ -#define E1000_RCTL_SBP 0x00000004 /* store bad packet */ -#define E1000_RCTL_UPE 0x00000008 /* unicast promiscuous enable */ -#define E1000_RCTL_MPE 0x00000010 /* multicast promiscuous enab */ -#define E1000_RCTL_LPE 0x00000020 /* long packet enable */ -#define E1000_RCTL_LBM_NO 0x00000000 /* no loopback mode */ -#define E1000_RCTL_LBM_MAC 0x00000040 /* MAC loopback mode */ -#define E1000_RCTL_LBM_SLP 0x00000080 /* serial link loopback mode */ -#define E1000_RCTL_LBM_TCVR 0x000000C0 /* tcvr loopback mode */ -#define E1000_RCTL_DTYP_MASK 0x00000C00 /* Descriptor type mask */ -#define E1000_RCTL_DTYP_PS 0x00000400 /* Packet Split descriptor */ -#define E1000_RCTL_RDMTS_HALF 0x00000000 /* rx desc min threshold size */ -#define E1000_RCTL_RDMTS_QUAT 0x00000100 /* rx desc min threshold size */ -#define E1000_RCTL_RDMTS_EIGTH 0x00000200 /* rx desc min threshold size */ -#define E1000_RCTL_MO_SHIFT 12 /* multicast offset shift */ -#define E1000_RCTL_MO_0 0x00000000 /* multicast offset 11:0 */ -#define E1000_RCTL_MO_1 0x00001000 /* multicast offset 12:1 */ -#define E1000_RCTL_MO_2 0x00002000 /* multicast offset 13:2 */ -#define E1000_RCTL_MO_3 0x00003000 /* multicast offset 15:4 */ -#define E1000_RCTL_MDR 0x00004000 /* multicast desc ring 0 */ -#define E1000_RCTL_BAM 0x00008000 /* broadcast enable */ -/* these buffer sizes are valid if E1000_RCTL_BSEX is 0 */ -#define E1000_RCTL_SZ_2048 0x00000000 /* rx buffer size 2048 */ -#define E1000_RCTL_SZ_1024 0x00010000 /* rx buffer size 1024 */ -#define E1000_RCTL_SZ_512 0x00020000 /* rx buffer size 512 */ -#define E1000_RCTL_SZ_256 0x00030000 /* rx buffer size 256 */ -/* these buffer sizes are valid if E1000_RCTL_BSEX is 1 */ -#define E1000_RCTL_SZ_16384 0x00010000 /* rx buffer size 16384 */ -#define E1000_RCTL_SZ_8192 0x00020000 /* rx buffer size 8192 */ -#define E1000_RCTL_SZ_4096 0x00030000 /* rx buffer size 4096 */ -#define E1000_RCTL_VFE 0x00040000 /* vlan filter enable */ -#define E1000_RCTL_CFIEN 0x00080000 /* canonical form enable */ -#define E1000_RCTL_CFI 0x00100000 /* canonical form indicator */ -#define E1000_RCTL_DPF 0x00400000 /* discard pause frames */ -#define E1000_RCTL_PMCF 0x00800000 /* pass MAC control frames */ -#define E1000_RCTL_BSEX 0x02000000 /* Buffer size extension */ -#define E1000_RCTL_SECRC 0x04000000 /* Strip Ethernet CRC */ -#define E1000_RCTL_FLXBUF_MASK 0x78000000 /* Flexible buffer size */ -#define E1000_RCTL_FLXBUF_SHIFT 27 /* Flexible buffer shift */ - -/* Use byte values for the following shift parameters - * Usage: - * psrctl |= (((ROUNDUP(value0, 128) >> E1000_PSRCTL_BSIZE0_SHIFT) & - * E1000_PSRCTL_BSIZE0_MASK) | - * ((ROUNDUP(value1, 1024) >> E1000_PSRCTL_BSIZE1_SHIFT) & - * E1000_PSRCTL_BSIZE1_MASK) | - * ((ROUNDUP(value2, 1024) << E1000_PSRCTL_BSIZE2_SHIFT) & - * E1000_PSRCTL_BSIZE2_MASK) | - * ((ROUNDUP(value3, 1024) << E1000_PSRCTL_BSIZE3_SHIFT) |; - * E1000_PSRCTL_BSIZE3_MASK)) - * where value0 = [128..16256], default=256 - * value1 = [1024..64512], default=4096 - * value2 = [0..64512], default=4096 - * value3 = [0..64512], default=0 - */ - -#define E1000_PSRCTL_BSIZE0_MASK 0x0000007F -#define E1000_PSRCTL_BSIZE1_MASK 0x00003F00 -#define E1000_PSRCTL_BSIZE2_MASK 0x003F0000 -#define E1000_PSRCTL_BSIZE3_MASK 0x3F000000 - -#define E1000_PSRCTL_BSIZE0_SHIFT 7 /* Shift _right_ 7 */ -#define E1000_PSRCTL_BSIZE1_SHIFT 2 /* Shift _right_ 2 */ -#define E1000_PSRCTL_BSIZE2_SHIFT 6 /* Shift _left_ 6 */ -#define E1000_PSRCTL_BSIZE3_SHIFT 14 /* Shift _left_ 14 */ - -/* SW_W_SYNC definitions */ -#define E1000_SWFW_EEP_SM 0x0001 -#define E1000_SWFW_PHY0_SM 0x0002 -#define E1000_SWFW_PHY1_SM 0x0004 -#define E1000_SWFW_MAC_CSR_SM 0x0008 - -/* Receive Descriptor */ -#define E1000_RDT_DELAY 0x0000ffff /* Delay timer (1=1024us) */ -#define E1000_RDT_FPDB 0x80000000 /* Flush descriptor block */ -#define E1000_RDLEN_LEN 0x0007ff80 /* descriptor length */ -#define E1000_RDH_RDH 0x0000ffff /* receive descriptor head */ -#define E1000_RDT_RDT 0x0000ffff /* receive descriptor tail */ - -/* Flow Control */ -#define E1000_FCRTH_RTH 0x0000FFF8 /* Mask Bits[15:3] for RTH */ -#define E1000_FCRTH_XFCE 0x80000000 /* External Flow Control Enable */ -#define E1000_FCRTL_RTL 0x0000FFF8 /* Mask Bits[15:3] for RTL */ -#define E1000_FCRTL_XONE 0x80000000 /* Enable XON frame transmission */ - -/* Flow Control Settings */ -#define E1000_FC_NONE 0 -#define E1000_FC_RX_PAUSE 1 -#define E1000_FC_TX_PAUSE 2 -#define E1000_FC_FULL 3 -#define E1000_FC_DEFAULT 0xFF - -/* Header split receive */ -#define E1000_RFCTL_ISCSI_DIS 0x00000001 -#define E1000_RFCTL_ISCSI_DWC_MASK 0x0000003E -#define E1000_RFCTL_ISCSI_DWC_SHIFT 1 -#define E1000_RFCTL_NFSW_DIS 0x00000040 -#define E1000_RFCTL_NFSR_DIS 0x00000080 -#define E1000_RFCTL_NFS_VER_MASK 0x00000300 -#define E1000_RFCTL_NFS_VER_SHIFT 8 -#define E1000_RFCTL_IPV6_DIS 0x00000400 -#define E1000_RFCTL_IPV6_XSUM_DIS 0x00000800 -#define E1000_RFCTL_ACK_DIS 0x00001000 -#define E1000_RFCTL_ACKD_DIS 0x00002000 -#define E1000_RFCTL_IPFRSP_DIS 0x00004000 -#define E1000_RFCTL_EXTEN 0x00008000 -#define E1000_RFCTL_IPV6_EX_DIS 0x00010000 -#define E1000_RFCTL_NEW_IPV6_EXT_DIS 0x00020000 - -/* Receive Descriptor Control */ -#define E1000_RXDCTL_PTHRESH 0x0000003F /* RXDCTL Prefetch Threshold */ -#define E1000_RXDCTL_HTHRESH 0x00003F00 /* RXDCTL Host Threshold */ -#define E1000_RXDCTL_WTHRESH 0x003F0000 /* RXDCTL Writeback Threshold */ -#define E1000_RXDCTL_GRAN 0x01000000 /* RXDCTL Granularity */ - -/* Transmit Descriptor Control */ -#define E1000_TXDCTL_PTHRESH 0x0000003F /* TXDCTL Prefetch Threshold */ -#define E1000_TXDCTL_HTHRESH 0x00003F00 /* TXDCTL Host Threshold */ -#define E1000_TXDCTL_WTHRESH 0x003F0000 /* TXDCTL Writeback Threshold */ -#define E1000_TXDCTL_GRAN 0x01000000 /* TXDCTL Granularity */ -#define E1000_TXDCTL_LWTHRESH 0xFE000000 /* TXDCTL Low Threshold */ -#define E1000_TXDCTL_FULL_TX_DESC_WB 0x01010000 /* GRAN=1, WTHRESH=1 */ -#define E1000_TXDCTL_COUNT_DESC 0x00400000 /* Enable the counting of desc. - still to be processed. */ -/* Transmit Configuration Word */ -#define E1000_TXCW_FD 0x00000020 /* TXCW full duplex */ -#define E1000_TXCW_HD 0x00000040 /* TXCW half duplex */ -#define E1000_TXCW_PAUSE 0x00000080 /* TXCW sym pause request */ -#define E1000_TXCW_ASM_DIR 0x00000100 /* TXCW astm pause direction */ -#define E1000_TXCW_PAUSE_MASK 0x00000180 /* TXCW pause request mask */ -#define E1000_TXCW_RF 0x00003000 /* TXCW remote fault */ -#define E1000_TXCW_NP 0x00008000 /* TXCW next page */ -#define E1000_TXCW_CW 0x0000ffff /* TxConfigWord mask */ -#define E1000_TXCW_TXC 0x40000000 /* Transmit Config control */ -#define E1000_TXCW_ANE 0x80000000 /* Auto-neg enable */ - -/* Receive Configuration Word */ -#define E1000_RXCW_CW 0x0000ffff /* RxConfigWord mask */ -#define E1000_RXCW_NC 0x04000000 /* Receive config no carrier */ -#define E1000_RXCW_IV 0x08000000 /* Receive config invalid */ -#define E1000_RXCW_CC 0x10000000 /* Receive config change */ -#define E1000_RXCW_C 0x20000000 /* Receive config */ -#define E1000_RXCW_SYNCH 0x40000000 /* Receive config synch */ -#define E1000_RXCW_ANC 0x80000000 /* Auto-neg complete */ - -/* Transmit Control */ -#define E1000_TCTL_RST 0x00000001 /* software reset */ -#define E1000_TCTL_EN 0x00000002 /* enable tx */ -#define E1000_TCTL_BCE 0x00000004 /* busy check enable */ -#define E1000_TCTL_PSP 0x00000008 /* pad short packets */ -#define E1000_TCTL_CT 0x00000ff0 /* collision threshold */ -#define E1000_TCTL_COLD 0x003ff000 /* collision distance */ -#define E1000_TCTL_SWXOFF 0x00400000 /* SW Xoff transmission */ -#define E1000_TCTL_PBE 0x00800000 /* Packet Burst Enable */ -#define E1000_TCTL_RTLC 0x01000000 /* Re-transmit on late collision */ -#define E1000_TCTL_NRTU 0x02000000 /* No Re-transmit on underrun */ -#define E1000_TCTL_MULR 0x10000000 /* Multiple request support */ -/* Extended Transmit Control */ -#define E1000_TCTL_EXT_BST_MASK 0x000003FF /* Backoff Slot Time */ -#define E1000_TCTL_EXT_GCEX_MASK 0x000FFC00 /* Gigabit Carry Extend Padding */ - -#define DEFAULT_80003ES2LAN_TCTL_EXT_GCEX 0x00010000 - -/* Receive Checksum Control */ -#define E1000_RXCSUM_PCSS_MASK 0x000000FF /* Packet Checksum Start */ -#define E1000_RXCSUM_IPOFL 0x00000100 /* IPv4 checksum offload */ -#define E1000_RXCSUM_TUOFL 0x00000200 /* TCP / UDP checksum offload */ -#define E1000_RXCSUM_IPV6OFL 0x00000400 /* IPv6 checksum offload */ -#define E1000_RXCSUM_IPPCSE 0x00001000 /* IP payload checksum enable */ -#define E1000_RXCSUM_PCSD 0x00002000 /* packet checksum disabled */ - -/* Multiple Receive Queue Control */ -#define E1000_MRQC_ENABLE_MASK 0x00000003 -#define E1000_MRQC_ENABLE_RSS_2Q 0x00000001 -#define E1000_MRQC_ENABLE_RSS_INT 0x00000004 -#define E1000_MRQC_RSS_FIELD_MASK 0xFFFF0000 -#define E1000_MRQC_RSS_FIELD_IPV4_TCP 0x00010000 -#define E1000_MRQC_RSS_FIELD_IPV4 0x00020000 -#define E1000_MRQC_RSS_FIELD_IPV6_TCP_EX 0x00040000 -#define E1000_MRQC_RSS_FIELD_IPV6_EX 0x00080000 -#define E1000_MRQC_RSS_FIELD_IPV6 0x00100000 -#define E1000_MRQC_RSS_FIELD_IPV6_TCP 0x00200000 - -/* Definitions for power management and wakeup registers */ -/* Wake Up Control */ -#define E1000_WUC_APME 0x00000001 /* APM Enable */ -#define E1000_WUC_PME_EN 0x00000002 /* PME Enable */ -#define E1000_WUC_PME_STATUS 0x00000004 /* PME Status */ -#define E1000_WUC_APMPME 0x00000008 /* Assert PME on APM Wakeup */ -#define E1000_WUC_SPM 0x80000000 /* Enable SPM */ - -/* Wake Up Filter Control */ -#define E1000_WUFC_LNKC 0x00000001 /* Link Status Change Wakeup Enable */ -#define E1000_WUFC_MAG 0x00000002 /* Magic Packet Wakeup Enable */ -#define E1000_WUFC_EX 0x00000004 /* Directed Exact Wakeup Enable */ -#define E1000_WUFC_MC 0x00000008 /* Directed Multicast Wakeup Enable */ -#define E1000_WUFC_BC 0x00000010 /* Broadcast Wakeup Enable */ -#define E1000_WUFC_ARP 0x00000020 /* ARP Request Packet Wakeup Enable */ -#define E1000_WUFC_IPV4 0x00000040 /* Directed IPv4 Packet Wakeup Enable */ -#define E1000_WUFC_IPV6 0x00000080 /* Directed IPv6 Packet Wakeup Enable */ -#define E1000_WUFC_IGNORE_TCO 0x00008000 /* Ignore WakeOn TCO packets */ -#define E1000_WUFC_FLX0 0x00010000 /* Flexible Filter 0 Enable */ -#define E1000_WUFC_FLX1 0x00020000 /* Flexible Filter 1 Enable */ -#define E1000_WUFC_FLX2 0x00040000 /* Flexible Filter 2 Enable */ -#define E1000_WUFC_FLX3 0x00080000 /* Flexible Filter 3 Enable */ -#define E1000_WUFC_ALL_FILTERS 0x000F00FF /* Mask for all wakeup filters */ -#define E1000_WUFC_FLX_OFFSET 16 /* Offset to the Flexible Filters bits */ -#define E1000_WUFC_FLX_FILTERS 0x000F0000 /* Mask for the 4 flexible filters */ - -/* Wake Up Status */ -#define E1000_WUS_LNKC 0x00000001 /* Link Status Changed */ -#define E1000_WUS_MAG 0x00000002 /* Magic Packet Received */ -#define E1000_WUS_EX 0x00000004 /* Directed Exact Received */ -#define E1000_WUS_MC 0x00000008 /* Directed Multicast Received */ -#define E1000_WUS_BC 0x00000010 /* Broadcast Received */ -#define E1000_WUS_ARP 0x00000020 /* ARP Request Packet Received */ -#define E1000_WUS_IPV4 0x00000040 /* Directed IPv4 Packet Wakeup Received */ -#define E1000_WUS_IPV6 0x00000080 /* Directed IPv6 Packet Wakeup Received */ -#define E1000_WUS_FLX0 0x00010000 /* Flexible Filter 0 Match */ -#define E1000_WUS_FLX1 0x00020000 /* Flexible Filter 1 Match */ -#define E1000_WUS_FLX2 0x00040000 /* Flexible Filter 2 Match */ -#define E1000_WUS_FLX3 0x00080000 /* Flexible Filter 3 Match */ -#define E1000_WUS_FLX_FILTERS 0x000F0000 /* Mask for the 4 flexible filters */ - -/* Management Control */ -#define E1000_MANC_SMBUS_EN 0x00000001 /* SMBus Enabled - RO */ -#define E1000_MANC_ASF_EN 0x00000002 /* ASF Enabled - RO */ -#define E1000_MANC_R_ON_FORCE 0x00000004 /* Reset on Force TCO - RO */ -#define E1000_MANC_RMCP_EN 0x00000100 /* Enable RCMP 026Fh Filtering */ -#define E1000_MANC_0298_EN 0x00000200 /* Enable RCMP 0298h Filtering */ -#define E1000_MANC_IPV4_EN 0x00000400 /* Enable IPv4 */ -#define E1000_MANC_IPV6_EN 0x00000800 /* Enable IPv6 */ -#define E1000_MANC_SNAP_EN 0x00001000 /* Accept LLC/SNAP */ -#define E1000_MANC_ARP_EN 0x00002000 /* Enable ARP Request Filtering */ -#define E1000_MANC_NEIGHBOR_EN 0x00004000 /* Enable Neighbor Discovery - * Filtering */ -#define E1000_MANC_ARP_RES_EN 0x00008000 /* Enable ARP response Filtering */ -#define E1000_MANC_TCO_RESET 0x00010000 /* TCO Reset Occurred */ -#define E1000_MANC_RCV_TCO_EN 0x00020000 /* Receive TCO Packets Enabled */ -#define E1000_MANC_REPORT_STATUS 0x00040000 /* Status Reporting Enabled */ -#define E1000_MANC_RCV_ALL 0x00080000 /* Receive All Enabled */ -#define E1000_MANC_BLK_PHY_RST_ON_IDE 0x00040000 /* Block phy resets */ -#define E1000_MANC_EN_MAC_ADDR_FILTER 0x00100000 /* Enable MAC address - * filtering */ -#define E1000_MANC_EN_MNG2HOST 0x00200000 /* Enable MNG packets to host - * memory */ -#define E1000_MANC_EN_IP_ADDR_FILTER 0x00400000 /* Enable IP address - * filtering */ -#define E1000_MANC_EN_XSUM_FILTER 0x00800000 /* Enable checksum filtering */ -#define E1000_MANC_BR_EN 0x01000000 /* Enable broadcast filtering */ -#define E1000_MANC_SMB_REQ 0x01000000 /* SMBus Request */ -#define E1000_MANC_SMB_GNT 0x02000000 /* SMBus Grant */ -#define E1000_MANC_SMB_CLK_IN 0x04000000 /* SMBus Clock In */ -#define E1000_MANC_SMB_DATA_IN 0x08000000 /* SMBus Data In */ -#define E1000_MANC_SMB_DATA_OUT 0x10000000 /* SMBus Data Out */ -#define E1000_MANC_SMB_CLK_OUT 0x20000000 /* SMBus Clock Out */ - -#define E1000_MANC_SMB_DATA_OUT_SHIFT 28 /* SMBus Data Out Shift */ -#define E1000_MANC_SMB_CLK_OUT_SHIFT 29 /* SMBus Clock Out Shift */ - -/* SW Semaphore Register */ -#define E1000_SWSM_SMBI 0x00000001 /* Driver Semaphore bit */ -#define E1000_SWSM_SWESMBI 0x00000002 /* FW Semaphore bit */ -#define E1000_SWSM_WMNG 0x00000004 /* Wake MNG Clock */ -#define E1000_SWSM_DRV_LOAD 0x00000008 /* Driver Loaded Bit */ - -/* FW Semaphore Register */ -#define E1000_FWSM_MODE_MASK 0x0000000E /* FW mode */ -#define E1000_FWSM_MODE_SHIFT 1 -#define E1000_FWSM_FW_VALID 0x00008000 /* FW established a valid mode */ - -#define E1000_FWSM_RSPCIPHY 0x00000040 /* Reset PHY on PCI reset */ -#define E1000_FWSM_DISSW 0x10000000 /* FW disable SW Write Access */ -#define E1000_FWSM_SKUSEL_MASK 0x60000000 /* LAN SKU select */ -#define E1000_FWSM_SKUEL_SHIFT 29 -#define E1000_FWSM_SKUSEL_EMB 0x0 /* Embedded SKU */ -#define E1000_FWSM_SKUSEL_CONS 0x1 /* Consumer SKU */ -#define E1000_FWSM_SKUSEL_PERF_100 0x2 /* Perf & Corp 10/100 SKU */ -#define E1000_FWSM_SKUSEL_PERF_GBE 0x3 /* Perf & Copr GbE SKU */ - -/* FFLT Debug Register */ -#define E1000_FFLT_DBG_INVC 0x00100000 /* Invalid /C/ code handling */ - -typedef enum { - em_mng_mode_none = 0, - em_mng_mode_asf, - em_mng_mode_pt, - em_mng_mode_ipmi, - em_mng_mode_host_interface_only -} em_mng_mode; - -/* Host Inteface Control Register */ -#define E1000_HICR_EN 0x00000001 /* Enable Bit - RO */ -#define E1000_HICR_C 0x00000002 /* Driver sets this bit when done - * to put command in RAM */ -#define E1000_HICR_SV 0x00000004 /* Status Validity */ -#define E1000_HICR_FWR 0x00000080 /* FW reset. Set by the Host */ - -/* Host Interface Command Interface - Address range 0x8800-0x8EFF */ -#define E1000_HI_MAX_DATA_LENGTH 252 /* Host Interface data length */ -#define E1000_HI_MAX_BLOCK_BYTE_LENGTH 1792 /* Number of bytes in range */ -#define E1000_HI_MAX_BLOCK_DWORD_LENGTH 448 /* Number of dwords in range */ -#define E1000_HI_COMMAND_TIMEOUT 500 /* Time in ms to process HI command */ - -struct em_host_command_header { - uint8_t command_id; - uint8_t command_length; - uint8_t command_options; /* I/F bits for command, status for return */ - uint8_t checksum; -}; -struct em_host_command_info { - struct em_host_command_header command_header; /* Command Head/Command Result Head has 4 bytes */ - uint8_t command_data[E1000_HI_MAX_DATA_LENGTH]; /* Command data can length 0..252 */ -}; - -/* Host SMB register #0 */ -#define E1000_HSMC0R_CLKIN 0x00000001 /* SMB Clock in */ -#define E1000_HSMC0R_DATAIN 0x00000002 /* SMB Data in */ -#define E1000_HSMC0R_DATAOUT 0x00000004 /* SMB Data out */ -#define E1000_HSMC0R_CLKOUT 0x00000008 /* SMB Clock out */ - -/* Host SMB register #1 */ -#define E1000_HSMC1R_CLKIN E1000_HSMC0R_CLKIN -#define E1000_HSMC1R_DATAIN E1000_HSMC0R_DATAIN -#define E1000_HSMC1R_DATAOUT E1000_HSMC0R_DATAOUT -#define E1000_HSMC1R_CLKOUT E1000_HSMC0R_CLKOUT - -/* FW Status Register */ -#define E1000_FWSTS_FWS_MASK 0x000000FF /* FW Status */ - -/* Wake Up Packet Length */ -#define E1000_WUPL_LENGTH_MASK 0x0FFF /* Only the lower 12 bits are valid */ - -#define E1000_MDALIGN 4096 - -/* PCI-Ex registers*/ - -/* PCI-Ex Control Register */ -#define E1000_GCR_RXD_NO_SNOOP 0x00000001 -#define E1000_GCR_RXDSCW_NO_SNOOP 0x00000002 -#define E1000_GCR_RXDSCR_NO_SNOOP 0x00000004 -#define E1000_GCR_TXD_NO_SNOOP 0x00000008 -#define E1000_GCR_TXDSCW_NO_SNOOP 0x00000010 -#define E1000_GCR_TXDSCR_NO_SNOOP 0x00000020 - -#define PCI_EX_NO_SNOOP_ALL (E1000_GCR_RXD_NO_SNOOP | \ - E1000_GCR_RXDSCW_NO_SNOOP | \ - E1000_GCR_RXDSCR_NO_SNOOP | \ - E1000_GCR_TXD_NO_SNOOP | \ - E1000_GCR_TXDSCW_NO_SNOOP | \ - E1000_GCR_TXDSCR_NO_SNOOP) - -#define PCI_EX_82566_SNOOP_ALL PCI_EX_NO_SNOOP_ALL - -#define E1000_GCR_L1_ACT_WITHOUT_L0S_RX 0x08000000 -/* Function Active and Power State to MNG */ -#define E1000_FACTPS_FUNC0_POWER_STATE_MASK 0x00000003 -#define E1000_FACTPS_LAN0_VALID 0x00000004 -#define E1000_FACTPS_FUNC0_AUX_EN 0x00000008 -#define E1000_FACTPS_FUNC1_POWER_STATE_MASK 0x000000C0 -#define E1000_FACTPS_FUNC1_POWER_STATE_SHIFT 6 -#define E1000_FACTPS_LAN1_VALID 0x00000100 -#define E1000_FACTPS_FUNC1_AUX_EN 0x00000200 -#define E1000_FACTPS_FUNC2_POWER_STATE_MASK 0x00003000 -#define E1000_FACTPS_FUNC2_POWER_STATE_SHIFT 12 -#define E1000_FACTPS_IDE_ENABLE 0x00004000 -#define E1000_FACTPS_FUNC2_AUX_EN 0x00008000 -#define E1000_FACTPS_FUNC3_POWER_STATE_MASK 0x000C0000 -#define E1000_FACTPS_FUNC3_POWER_STATE_SHIFT 18 -#define E1000_FACTPS_SP_ENABLE 0x00100000 -#define E1000_FACTPS_FUNC3_AUX_EN 0x00200000 -#define E1000_FACTPS_FUNC4_POWER_STATE_MASK 0x03000000 -#define E1000_FACTPS_FUNC4_POWER_STATE_SHIFT 24 -#define E1000_FACTPS_IPMI_ENABLE 0x04000000 -#define E1000_FACTPS_FUNC4_AUX_EN 0x08000000 -#define E1000_FACTPS_MNGCG 0x20000000 -#define E1000_FACTPS_LAN_FUNC_SEL 0x40000000 -#define E1000_FACTPS_PM_STATE_CHANGED 0x80000000 - -/* PCI-Ex Config Space */ -#define PCI_EX_LINK_STATUS 0x12 -#define PCI_EX_LINK_WIDTH_MASK 0x3F0 -#define PCI_EX_LINK_WIDTH_SHIFT 4 - -/* EEPROM Commands - Microwire */ -#define EEPROM_READ_OPCODE_MICROWIRE 0x6 /* EEPROM read opcode */ -#define EEPROM_WRITE_OPCODE_MICROWIRE 0x5 /* EEPROM write opcode */ -#define EEPROM_ERASE_OPCODE_MICROWIRE 0x7 /* EEPROM erase opcode */ -#define EEPROM_EWEN_OPCODE_MICROWIRE 0x13 /* EEPROM erase/write enable */ -#define EEPROM_EWDS_OPCODE_MICROWIRE 0x10 /* EEPROM erast/write disable */ - -/* EEPROM Commands - SPI */ -#define EEPROM_MAX_RETRY_SPI 5000 /* Max wait of 5ms, for RDY signal */ -#define EEPROM_READ_OPCODE_SPI 0x03 /* EEPROM read opcode */ -#define EEPROM_WRITE_OPCODE_SPI 0x02 /* EEPROM write opcode */ -#define EEPROM_A8_OPCODE_SPI 0x08 /* opcode bit-3 = address bit-8 */ -#define EEPROM_WREN_OPCODE_SPI 0x06 /* EEPROM set Write Enable latch */ -#define EEPROM_WRDI_OPCODE_SPI 0x04 /* EEPROM reset Write Enable latch */ -#define EEPROM_RDSR_OPCODE_SPI 0x05 /* EEPROM read Status register */ -#define EEPROM_WRSR_OPCODE_SPI 0x01 /* EEPROM write Status register */ -#define EEPROM_ERASE4K_OPCODE_SPI 0x20 /* EEPROM ERASE 4KB */ -#define EEPROM_ERASE64K_OPCODE_SPI 0xD8 /* EEPROM ERASE 64KB */ -#define EEPROM_ERASE256_OPCODE_SPI 0xDB /* EEPROM ERASE 256B */ - -/* EEPROM Size definitions */ -#define EEPROM_WORD_SIZE_SHIFT 6 -#define EEPROM_SIZE_SHIFT 10 -#define EEPROM_SIZE_MASK 0x1C00 - -/* EEPROM Word Offsets */ -#define EEPROM_COMPAT 0x0003 -#define EEPROM_ID_LED_SETTINGS 0x0004 -#define EEPROM_VERSION 0x0005 -#define EEPROM_SERDES_AMPLITUDE 0x0006 /* For SERDES output amplitude adjustment. */ -#define EEPROM_PHY_CLASS_WORD 0x0007 -#define EEPROM_INIT_CONTROL1_REG 0x000A -#define EEPROM_INIT_CONTROL2_REG 0x000F -#define EEPROM_SWDEF_PINS_CTRL_PORT_1 0x0010 -#define EEPROM_INIT_CONTROL3_PORT_B 0x0014 -#define EEPROM_INIT_3GIO_3 0x001A -#define EEPROM_SWDEF_PINS_CTRL_PORT_0 0x0020 -#define EEPROM_INIT_CONTROL3_PORT_A 0x0024 -#define EEPROM_CFG 0x0012 -#define EEPROM_FLASH_VERSION 0x0032 -#define EEPROM_CHECKSUM_REG 0x003F - -#define E1000_EEPROM_CFG_DONE 0x00040000 /* MNG config cycle done */ -#define E1000_EEPROM_CFG_DONE_PORT_1 0x00080000 /* ...for second port */ - -/* Word definitions for ID LED Settings */ -#define ID_LED_RESERVED_0000 0x0000 -#define ID_LED_RESERVED_FFFF 0xFFFF -#define ID_LED_RESERVED_82573 0xF746 -#define ID_LED_DEFAULT_82573 0x1811 -#define ID_LED_DEFAULT ((ID_LED_OFF1_ON2 << 12) | \ - (ID_LED_OFF1_OFF2 << 8) | \ - (ID_LED_DEF1_DEF2 << 4) | \ - (ID_LED_DEF1_DEF2)) -#define ID_LED_DEFAULT_ICH8LAN ((ID_LED_DEF1_DEF2 << 12) | \ - (ID_LED_DEF1_OFF2 << 8) | \ - (ID_LED_DEF1_ON2 << 4) | \ - (ID_LED_DEF1_DEF2)) -#define ID_LED_DEF1_DEF2 0x1 -#define ID_LED_DEF1_ON2 0x2 -#define ID_LED_DEF1_OFF2 0x3 -#define ID_LED_ON1_DEF2 0x4 -#define ID_LED_ON1_ON2 0x5 -#define ID_LED_ON1_OFF2 0x6 -#define ID_LED_OFF1_DEF2 0x7 -#define ID_LED_OFF1_ON2 0x8 -#define ID_LED_OFF1_OFF2 0x9 - -#define IGP_ACTIVITY_LED_MASK 0xFFFFF0FF -#define IGP_ACTIVITY_LED_ENABLE 0x0300 -#define IGP_LED3_MODE 0x07000000 - - -/* Mask bits for SERDES amplitude adjustment in Word 6 of the EEPROM */ -#define EEPROM_SERDES_AMPLITUDE_MASK 0x000F - -/* Mask bit for PHY class in Word 7 of the EEPROM */ -#define EEPROM_PHY_CLASS_A 0x8000 - -/* Mask bits for fields in Word 0x0a of the EEPROM */ -#define EEPROM_WORD0A_ILOS 0x0010 -#define EEPROM_WORD0A_SWDPIO 0x01E0 -#define EEPROM_WORD0A_LRST 0x0200 -#define EEPROM_WORD0A_FD 0x0400 -#define EEPROM_WORD0A_66MHZ 0x0800 - -/* Mask bits for fields in Word 0x0f of the EEPROM */ -#define EEPROM_WORD0F_PAUSE_MASK 0x3000 -#define EEPROM_WORD0F_PAUSE 0x1000 -#define EEPROM_WORD0F_ASM_DIR 0x2000 -#define EEPROM_WORD0F_ANE 0x0800 -#define EEPROM_WORD0F_SWPDIO_EXT 0x00F0 -#define EEPROM_WORD0F_LPLU 0x0001 - -/* Mask bits for fields in Word 0x10/0x20 of the EEPROM */ -#define EEPROM_WORD1020_GIGA_DISABLE 0x0010 -#define EEPROM_WORD1020_GIGA_DISABLE_NON_D0A 0x0008 - -/* Mask bits for fields in Word 0x1a of the EEPROM */ -#define EEPROM_WORD1A_ASPM_MASK 0x000C - -/* For checksumming, the sum of all words in the EEPROM should equal 0xBABA. */ -#define EEPROM_SUM 0xBABA - -/* EEPROM Map defines (WORD OFFSETS)*/ -#define EEPROM_NODE_ADDRESS_BYTE_0 0 -#define EEPROM_PBA_BYTE_1 8 - -#define EEPROM_RESERVED_WORD 0xFFFF - -/* EEPROM Map Sizes (Byte Counts) */ -#define PBA_SIZE 4 - -/* Collision related configuration parameters */ -#define E1000_COLLISION_THRESHOLD 15 -#define E1000_CT_SHIFT 4 -/* Collision distance is a 0-based value that applies to - * half-duplex-capable hardware only. */ -#define E1000_COLLISION_DISTANCE 63 -#define E1000_COLLISION_DISTANCE_82542 64 -#define E1000_FDX_COLLISION_DISTANCE E1000_COLLISION_DISTANCE -#define E1000_HDX_COLLISION_DISTANCE E1000_COLLISION_DISTANCE -#define E1000_COLD_SHIFT 12 - -/* Number of Transmit and Receive Descriptors must be a multiple of 8 */ -#define REQ_TX_DESCRIPTOR_MULTIPLE 8 -#define REQ_RX_DESCRIPTOR_MULTIPLE 8 - -/* Default values for the transmit IPG register */ -#define DEFAULT_82542_TIPG_IPGT 10 -#define DEFAULT_82543_TIPG_IPGT_FIBER 9 -#define DEFAULT_82543_TIPG_IPGT_COPPER 8 - -#define E1000_TIPG_IPGT_MASK 0x000003FF -#define E1000_TIPG_IPGR1_MASK 0x000FFC00 -#define E1000_TIPG_IPGR2_MASK 0x3FF00000 - -#define DEFAULT_82542_TIPG_IPGR1 2 -#define DEFAULT_82543_TIPG_IPGR1 8 -#define E1000_TIPG_IPGR1_SHIFT 10 - -#define DEFAULT_82542_TIPG_IPGR2 10 -#define DEFAULT_82543_TIPG_IPGR2 6 -#define DEFAULT_80003ES2LAN_TIPG_IPGR2 7 -#define E1000_TIPG_IPGR2_SHIFT 20 - -#define DEFAULT_80003ES2LAN_TIPG_IPGT_10_100 0x00000009 -#define DEFAULT_80003ES2LAN_TIPG_IPGT_1000 0x00000008 -#define E1000_TXDMAC_DPP 0x00000001 - -/* Adaptive IFS defines */ -#define TX_THRESHOLD_START 8 -#define TX_THRESHOLD_INCREMENT 10 -#define TX_THRESHOLD_DECREMENT 1 -#define TX_THRESHOLD_STOP 190 -#define TX_THRESHOLD_DISABLE 0 -#define TX_THRESHOLD_TIMER_MS 10000 -#define MIN_NUM_XMITS 1000 -#define IFS_MAX 80 -#define IFS_STEP 10 -#define IFS_MIN 40 -#define IFS_RATIO 4 - -/* Extended Configuration Control and Size */ -#define E1000_EXTCNF_CTRL_PCIE_WRITE_ENABLE 0x00000001 -#define E1000_EXTCNF_CTRL_PHY_WRITE_ENABLE 0x00000002 -#define E1000_EXTCNF_CTRL_D_UD_ENABLE 0x00000004 -#define E1000_EXTCNF_CTRL_D_UD_LATENCY 0x00000008 -#define E1000_EXTCNF_CTRL_D_UD_OWNER 0x00000010 -#define E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP 0x00000020 -#define E1000_EXTCNF_CTRL_MDIO_HW_OWNERSHIP 0x00000040 -#define E1000_EXTCNF_CTRL_EXT_CNF_POINTER 0x0FFF0000 - -#define E1000_EXTCNF_SIZE_EXT_PHY_LENGTH 0x000000FF -#define E1000_EXTCNF_SIZE_EXT_DOCK_LENGTH 0x0000FF00 -#define E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH 0x00FF0000 -#define E1000_EXTCNF_CTRL_LCD_WRITE_ENABLE 0x00000001 -#define E1000_EXTCNF_CTRL_SWFLAG 0x00000020 - -/* PBA constants */ -#define E1000_PBA_8K 0x0008 /* 8KB, default Rx allocation */ -#define E1000_PBA_12K 0x000C /* 12KB, default Rx allocation */ -#define E1000_PBA_16K 0x0010 /* 16KB, default TX allocation */ -#define E1000_PBA_22K 0x0016 -#define E1000_PBA_24K 0x0018 -#define E1000_PBA_30K 0x001E -#define E1000_PBA_32K 0x0020 -#define E1000_PBA_34K 0x0022 -#define E1000_PBA_38K 0x0026 -#define E1000_PBA_40K 0x0028 -#define E1000_PBA_48K 0x0030 /* 48KB, default RX allocation */ - -#define E1000_PBS_16K E1000_PBA_16K - -/* Flow Control Constants */ -#define FLOW_CONTROL_ADDRESS_LOW 0x00C28001 -#define FLOW_CONTROL_ADDRESS_HIGH 0x00000100 -#define FLOW_CONTROL_TYPE 0x8808 - -/* The historical defaults for the flow control values are given below. */ -#define FC_DEFAULT_HI_THRESH (0x8000) /* 32KB */ -#define FC_DEFAULT_LO_THRESH (0x4000) /* 16KB */ -#define FC_DEFAULT_TX_TIMER (0x100) /* ~130 us */ - -/* PCIX Config space */ -#define PCIX_COMMAND_REGISTER 0xE6 -#define PCIX_STATUS_REGISTER_LO 0xE8 -#define PCIX_STATUS_REGISTER_HI 0xEA - -#define PCIX_COMMAND_MMRBC_MASK 0x000C -#define PCIX_COMMAND_MMRBC_SHIFT 0x2 -#define PCIX_STATUS_HI_MMRBC_MASK 0x0060 -#define PCIX_STATUS_HI_MMRBC_SHIFT 0x5 -#define PCIX_STATUS_HI_MMRBC_4K 0x3 -#define PCIX_STATUS_HI_MMRBC_2K 0x2 - - -/* Number of bits required to shift right the "pause" bits from the - * EEPROM (bits 13:12) to the "pause" (bits 8:7) field in the TXCW register. - */ -#define PAUSE_SHIFT 5 - -/* Number of bits required to shift left the "SWDPIO" bits from the - * EEPROM (bits 8:5) to the "SWDPIO" (bits 25:22) field in the CTRL register. - */ -#define SWDPIO_SHIFT 17 - -/* Number of bits required to shift left the "SWDPIO_EXT" bits from the - * EEPROM word F (bits 7:4) to the bits 11:8 of The Extended CTRL register. - */ -#define SWDPIO__EXT_SHIFT 4 - -/* Number of bits required to shift left the "ILOS" bit from the EEPROM - * (bit 4) to the "ILOS" (bit 7) field in the CTRL register. - */ -#define ILOS_SHIFT 3 - - -#define RECEIVE_BUFFER_ALIGN_SIZE (256) - -/* Number of milliseconds we wait for auto-negotiation to complete */ -#define LINK_UP_TIMEOUT 500 - -/* Number of 100 microseconds we wait for PCI Express master disable */ -#define MASTER_DISABLE_TIMEOUT 800 -/* Number of milliseconds we wait for Eeprom auto read bit done after MAC reset */ -#define AUTO_READ_DONE_TIMEOUT 10 -/* Number of milliseconds we wait for PHY configuration done after MAC reset */ -#define PHY_CFG_TIMEOUT 100 - -#define E1000_TX_BUFFER_SIZE ((uint32_t)1514) - -/* The carrier extension symbol, as received by the NIC. */ -#define CARRIER_EXTENSION 0x0F - -/* TBI_ACCEPT macro definition: - * - * This macro requires: - * adapter = a pointer to struct em_hw - * status = the 8 bit status field of the RX descriptor with EOP set - * error = the 8 bit error field of the RX descriptor with EOP set - * length = the sum of all the length fields of the RX descriptors that - * make up the current frame - * last_byte = the last byte of the frame DMAed by the hardware - * max_frame_length = the maximum frame length we want to accept. - * min_frame_length = the minimum frame length we want to accept. - * - * This macro is a conditional that should be used in the interrupt - * handler's Rx processing routine when RxErrors have been detected. - * - * Typical use: - * ... - * if (TBI_ACCEPT) { - * accept_frame = TRUE; - * em_tbi_adjust_stats(adapter, MacAddress); - * frame_length--; - * } else { - * accept_frame = FALSE; - * } - * ... - */ - -#define TBI_ACCEPT(adapter, status, errors, length, last_byte) \ - ((adapter)->tbi_compatibility_on && \ - (((errors) & E1000_RXD_ERR_FRAME_ERR_MASK) == E1000_RXD_ERR_CE) && \ - ((last_byte) == CARRIER_EXTENSION) && \ - (((status) & E1000_RXD_STAT_VP) ? \ - (((length) > ((adapter)->min_frame_size - VLAN_TAG_SIZE)) && \ - ((length) <= ((adapter)->max_frame_size + 1))) : \ - (((length) > (adapter)->min_frame_size) && \ - ((length) <= ((adapter)->max_frame_size + VLAN_TAG_SIZE + 1))))) - - -/* Structures, enums, and macros for the PHY */ - -/* Bit definitions for the Management Data IO (MDIO) and Management Data - * Clock (MDC) pins in the Device Control Register. - */ -#define E1000_CTRL_PHY_RESET_DIR E1000_CTRL_SWDPIO0 -#define E1000_CTRL_PHY_RESET E1000_CTRL_SWDPIN0 -#define E1000_CTRL_MDIO_DIR E1000_CTRL_SWDPIO2 -#define E1000_CTRL_MDIO E1000_CTRL_SWDPIN2 -#define E1000_CTRL_MDC_DIR E1000_CTRL_SWDPIO3 -#define E1000_CTRL_MDC E1000_CTRL_SWDPIN3 -#define E1000_CTRL_PHY_RESET_DIR4 E1000_CTRL_EXT_SDP4_DIR -#define E1000_CTRL_PHY_RESET4 E1000_CTRL_EXT_SDP4_DATA - - -/* PHY 1000 MII Register/Bit Definitions */ -/* PHY Registers defined by IEEE */ -#define PHY_CTRL 0x00 /* Control Register */ -#define PHY_STATUS 0x01 /* Status Regiser */ -#define PHY_ID1 0x02 /* Phy Id Reg (word 1) */ -#define PHY_ID2 0x03 /* Phy Id Reg (word 2) */ -#define PHY_AUTONEG_ADV 0x04 /* Autoneg Advertisement */ -#define PHY_LP_ABILITY 0x05 /* Link Partner Ability (Base Page) */ -#define PHY_AUTONEG_EXP 0x06 /* Autoneg Expansion Reg */ -#define PHY_NEXT_PAGE_TX 0x07 /* Next Page TX */ -#define PHY_LP_NEXT_PAGE 0x08 /* Link Partner Next Page */ -#define PHY_1000T_CTRL 0x09 /* 1000Base-T Control Reg */ -#define PHY_1000T_STATUS 0x0A /* 1000Base-T Status Reg */ -#define PHY_EXT_STATUS 0x0F /* Extended Status Reg */ - -#define MAX_PHY_REG_ADDRESS 0x1F /* 5 bit address bus (0-0x1F) */ -#define MAX_PHY_MULTI_PAGE_REG 0xF /* Registers equal on all pages */ - -/* M88E1000 Specific Registers */ -#define M88E1000_PHY_SPEC_CTRL 0x10 /* PHY Specific Control Register */ -#define M88E1000_PHY_SPEC_STATUS 0x11 /* PHY Specific Status Register */ -#define M88E1000_INT_ENABLE 0x12 /* Interrupt Enable Register */ -#define M88E1000_INT_STATUS 0x13 /* Interrupt Status Register */ -#define M88E1000_EXT_PHY_SPEC_CTRL 0x14 /* Extended PHY Specific Control */ -#define M88E1000_RX_ERR_CNTR 0x15 /* Receive Error Counter */ - -#define M88E1000_PHY_EXT_CTRL 0x1A /* PHY extend control register */ -#define M88E1000_PHY_PAGE_SELECT 0x1D /* Reg 29 for page number setting */ -#define M88E1000_PHY_GEN_CONTROL 0x1E /* Its meaning depends on reg 29 */ -#define M88E1000_PHY_VCO_REG_BIT8 0x100 /* Bits 8 & 11 are adjusted for */ -#define M88E1000_PHY_VCO_REG_BIT11 0x800 /* improved BER performance */ - -#define IGP01E1000_IEEE_REGS_PAGE 0x0000 -#define IGP01E1000_IEEE_RESTART_AUTONEG 0x3300 -#define IGP01E1000_IEEE_FORCE_GIGA 0x0140 - -/* IGP01E1000 Specific Registers */ -#define IGP01E1000_PHY_PORT_CONFIG 0x10 /* PHY Specific Port Config Register */ -#define IGP01E1000_PHY_PORT_STATUS 0x11 /* PHY Specific Status Register */ -#define IGP01E1000_PHY_PORT_CTRL 0x12 /* PHY Specific Control Register */ -#define IGP01E1000_PHY_LINK_HEALTH 0x13 /* PHY Link Health Register */ -#define IGP01E1000_GMII_FIFO 0x14 /* GMII FIFO Register */ -#define IGP01E1000_PHY_CHANNEL_QUALITY 0x15 /* PHY Channel Quality Register */ -#define IGP02E1000_PHY_POWER_MGMT 0x19 -#define IGP01E1000_PHY_PAGE_SELECT 0x1F /* PHY Page Select Core Register */ - -/* IGP01E1000 AGC Registers - stores the cable length values*/ -#define IGP01E1000_PHY_AGC_A 0x1172 -#define IGP01E1000_PHY_AGC_B 0x1272 -#define IGP01E1000_PHY_AGC_C 0x1472 -#define IGP01E1000_PHY_AGC_D 0x1872 - -/* IGP02E1000 AGC Registers for cable length values */ -#define IGP02E1000_PHY_AGC_A 0x11B1 -#define IGP02E1000_PHY_AGC_B 0x12B1 -#define IGP02E1000_PHY_AGC_C 0x14B1 -#define IGP02E1000_PHY_AGC_D 0x18B1 - -/* IGP01E1000 DSP Reset Register */ -#define IGP01E1000_PHY_DSP_RESET 0x1F33 -#define IGP01E1000_PHY_DSP_SET 0x1F71 -#define IGP01E1000_PHY_DSP_FFE 0x1F35 - -#define IGP01E1000_PHY_CHANNEL_NUM 4 -#define IGP02E1000_PHY_CHANNEL_NUM 4 - -#define IGP01E1000_PHY_AGC_PARAM_A 0x1171 -#define IGP01E1000_PHY_AGC_PARAM_B 0x1271 -#define IGP01E1000_PHY_AGC_PARAM_C 0x1471 -#define IGP01E1000_PHY_AGC_PARAM_D 0x1871 - -#define IGP01E1000_PHY_EDAC_MU_INDEX 0xC000 -#define IGP01E1000_PHY_EDAC_SIGN_EXT_9_BITS 0x8000 - -#define IGP01E1000_PHY_ANALOG_TX_STATE 0x2890 -#define IGP01E1000_PHY_ANALOG_CLASS_A 0x2000 -#define IGP01E1000_PHY_FORCE_ANALOG_ENABLE 0x0004 -#define IGP01E1000_PHY_DSP_FFE_CM_CP 0x0069 - -#define IGP01E1000_PHY_DSP_FFE_DEFAULT 0x002A -/* IGP01E1000 PCS Initialization register - stores the polarity status when - * speed = 1000 Mbps. */ -#define IGP01E1000_PHY_PCS_INIT_REG 0x00B4 -#define IGP01E1000_PHY_PCS_CTRL_REG 0x00B5 - -#define IGP01E1000_ANALOG_REGS_PAGE 0x20C0 - -/* Bits... - * 15-5: page - * 4-0: register offset - */ -#define GG82563_PAGE_SHIFT 5 -#define GG82563_REG(page, reg) \ - (((page) << GG82563_PAGE_SHIFT) | ((reg) & MAX_PHY_REG_ADDRESS)) -#define GG82563_MIN_ALT_REG 30 - -/* GG82563 Specific Registers */ -#define GG82563_PHY_SPEC_CTRL \ - GG82563_REG(0, 16) /* PHY Specific Control */ -#define GG82563_PHY_SPEC_STATUS \ - GG82563_REG(0, 17) /* PHY Specific Status */ -#define GG82563_PHY_INT_ENABLE \ - GG82563_REG(0, 18) /* Interrupt Enable */ -#define GG82563_PHY_SPEC_STATUS_2 \ - GG82563_REG(0, 19) /* PHY Specific Status 2 */ -#define GG82563_PHY_RX_ERR_CNTR \ - GG82563_REG(0, 21) /* Receive Error Counter */ -#define GG82563_PHY_PAGE_SELECT \ - GG82563_REG(0, 22) /* Page Select */ -#define GG82563_PHY_SPEC_CTRL_2 \ - GG82563_REG(0, 26) /* PHY Specific Control 2 */ -#define GG82563_PHY_PAGE_SELECT_ALT \ - GG82563_REG(0, 29) /* Alternate Page Select */ -#define GG82563_PHY_TEST_CLK_CTRL \ - GG82563_REG(0, 30) /* Test Clock Control (use reg. 29 to select) */ - -#define GG82563_PHY_MAC_SPEC_CTRL \ - GG82563_REG(2, 21) /* MAC Specific Control Register */ -#define GG82563_PHY_MAC_SPEC_CTRL_2 \ - GG82563_REG(2, 26) /* MAC Specific Control 2 */ - -#define GG82563_PHY_DSP_DISTANCE \ - GG82563_REG(5, 26) /* DSP Distance */ - -/* Page 193 - Port Control Registers */ -#define GG82563_PHY_KMRN_MODE_CTRL \ - GG82563_REG(193, 16) /* Kumeran Mode Control */ -#define GG82563_PHY_PORT_RESET \ - GG82563_REG(193, 17) /* Port Reset */ -#define GG82563_PHY_REVISION_ID \ - GG82563_REG(193, 18) /* Revision ID */ -#define GG82563_PHY_DEVICE_ID \ - GG82563_REG(193, 19) /* Device ID */ -#define GG82563_PHY_PWR_MGMT_CTRL \ - GG82563_REG(193, 20) /* Power Management Control */ -#define GG82563_PHY_RATE_ADAPT_CTRL \ - GG82563_REG(193, 25) /* Rate Adaptation Control */ - -/* Page 194 - KMRN Registers */ -#define GG82563_PHY_KMRN_FIFO_CTRL_STAT \ - GG82563_REG(194, 16) /* FIFO's Control/Status */ -#define GG82563_PHY_KMRN_CTRL \ - GG82563_REG(194, 17) /* Control */ -#define GG82563_PHY_INBAND_CTRL \ - GG82563_REG(194, 18) /* Inband Control */ -#define GG82563_PHY_KMRN_DIAGNOSTIC \ - GG82563_REG(194, 19) /* Diagnostic */ -#define GG82563_PHY_ACK_TIMEOUTS \ - GG82563_REG(194, 20) /* Acknowledge Timeouts */ -#define GG82563_PHY_ADV_ABILITY \ - GG82563_REG(194, 21) /* Advertised Ability */ -#define GG82563_PHY_LINK_PARTNER_ADV_ABILITY \ - GG82563_REG(194, 23) /* Link Partner Advertised Ability */ -#define GG82563_PHY_ADV_NEXT_PAGE \ - GG82563_REG(194, 24) /* Advertised Next Page */ -#define GG82563_PHY_LINK_PARTNER_ADV_NEXT_PAGE \ - GG82563_REG(194, 25) /* Link Partner Advertised Next page */ -#define GG82563_PHY_KMRN_MISC \ - GG82563_REG(194, 26) /* Misc. */ - -/* PHY Control Register */ -#define MII_CR_SPEED_SELECT_MSB 0x0040 /* bits 6,13: 10=1000, 01=100, 00=10 */ -#define MII_CR_COLL_TEST_ENABLE 0x0080 /* Collision test enable */ -#define MII_CR_FULL_DUPLEX 0x0100 /* FDX =1, half duplex =0 */ -#define MII_CR_RESTART_AUTO_NEG 0x0200 /* Restart auto negotiation */ -#define MII_CR_ISOLATE 0x0400 /* Isolate PHY from MII */ -#define MII_CR_POWER_DOWN 0x0800 /* Power down */ -#define MII_CR_AUTO_NEG_EN 0x1000 /* Auto Neg Enable */ -#define MII_CR_SPEED_SELECT_LSB 0x2000 /* bits 6,13: 10=1000, 01=100, 00=10 */ -#define MII_CR_LOOPBACK 0x4000 /* 0 = normal, 1 = loopback */ -#define MII_CR_RESET 0x8000 /* 0 = normal, 1 = PHY reset */ - -/* PHY Status Register */ -#define MII_SR_EXTENDED_CAPS 0x0001 /* Extended register capabilities */ -#define MII_SR_JABBER_DETECT 0x0002 /* Jabber Detected */ -#define MII_SR_LINK_STATUS 0x0004 /* Link Status 1 = link */ -#define MII_SR_AUTONEG_CAPS 0x0008 /* Auto Neg Capable */ -#define MII_SR_REMOTE_FAULT 0x0010 /* Remote Fault Detect */ -#define MII_SR_AUTONEG_COMPLETE 0x0020 /* Auto Neg Complete */ -#define MII_SR_PREAMBLE_SUPPRESS 0x0040 /* Preamble may be suppressed */ -#define MII_SR_EXTENDED_STATUS 0x0100 /* Ext. status info in Reg 0x0F */ -#define MII_SR_100T2_HD_CAPS 0x0200 /* 100T2 Half Duplex Capable */ -#define MII_SR_100T2_FD_CAPS 0x0400 /* 100T2 Full Duplex Capable */ -#define MII_SR_10T_HD_CAPS 0x0800 /* 10T Half Duplex Capable */ -#define MII_SR_10T_FD_CAPS 0x1000 /* 10T Full Duplex Capable */ -#define MII_SR_100X_HD_CAPS 0x2000 /* 100X Half Duplex Capable */ -#define MII_SR_100X_FD_CAPS 0x4000 /* 100X Full Duplex Capable */ -#define MII_SR_100T4_CAPS 0x8000 /* 100T4 Capable */ - -/* Autoneg Advertisement Register */ -#define NWAY_AR_SELECTOR_FIELD 0x0001 /* indicates IEEE 802.3 CSMA/CD */ -#define NWAY_AR_10T_HD_CAPS 0x0020 /* 10T Half Duplex Capable */ -#define NWAY_AR_10T_FD_CAPS 0x0040 /* 10T Full Duplex Capable */ -#define NWAY_AR_100TX_HD_CAPS 0x0080 /* 100TX Half Duplex Capable */ -#define NWAY_AR_100TX_FD_CAPS 0x0100 /* 100TX Full Duplex Capable */ -#define NWAY_AR_100T4_CAPS 0x0200 /* 100T4 Capable */ -#define NWAY_AR_PAUSE 0x0400 /* Pause operation desired */ -#define NWAY_AR_ASM_DIR 0x0800 /* Asymmetric Pause Direction bit */ -#define NWAY_AR_REMOTE_FAULT 0x2000 /* Remote Fault detected */ -#define NWAY_AR_NEXT_PAGE 0x8000 /* Next Page ability supported */ - -/* Link Partner Ability Register (Base Page) */ -#define NWAY_LPAR_SELECTOR_FIELD 0x0000 /* LP protocol selector field */ -#define NWAY_LPAR_10T_HD_CAPS 0x0020 /* LP is 10T Half Duplex Capable */ -#define NWAY_LPAR_10T_FD_CAPS 0x0040 /* LP is 10T Full Duplex Capable */ -#define NWAY_LPAR_100TX_HD_CAPS 0x0080 /* LP is 100TX Half Duplex Capable */ -#define NWAY_LPAR_100TX_FD_CAPS 0x0100 /* LP is 100TX Full Duplex Capable */ -#define NWAY_LPAR_100T4_CAPS 0x0200 /* LP is 100T4 Capable */ -#define NWAY_LPAR_PAUSE 0x0400 /* LP Pause operation desired */ -#define NWAY_LPAR_ASM_DIR 0x0800 /* LP Asymmetric Pause Direction bit */ -#define NWAY_LPAR_REMOTE_FAULT 0x2000 /* LP has detected Remote Fault */ -#define NWAY_LPAR_ACKNOWLEDGE 0x4000 /* LP has rx'd link code word */ -#define NWAY_LPAR_NEXT_PAGE 0x8000 /* Next Page ability supported */ - -/* Autoneg Expansion Register */ -#define NWAY_ER_LP_NWAY_CAPS 0x0001 /* LP has Auto Neg Capability */ -#define NWAY_ER_PAGE_RXD 0x0002 /* LP is 10T Half Duplex Capable */ -#define NWAY_ER_NEXT_PAGE_CAPS 0x0004 /* LP is 10T Full Duplex Capable */ -#define NWAY_ER_LP_NEXT_PAGE_CAPS 0x0008 /* LP is 100TX Half Duplex Capable */ -#define NWAY_ER_PAR_DETECT_FAULT 0x0010 /* LP is 100TX Full Duplex Capable */ - -/* Next Page TX Register */ -#define NPTX_MSG_CODE_FIELD 0x0001 /* NP msg code or unformatted data */ -#define NPTX_TOGGLE 0x0800 /* Toggles between exchanges - * of different NP - */ -#define NPTX_ACKNOWLDGE2 0x1000 /* 1 = will comply with msg - * 0 = cannot comply with msg - */ -#define NPTX_MSG_PAGE 0x2000 /* formatted(1)/unformatted(0) pg */ -#define NPTX_NEXT_PAGE 0x8000 /* 1 = addition NP will follow - * 0 = sending last NP - */ - -/* Link Partner Next Page Register */ -#define LP_RNPR_MSG_CODE_FIELD 0x0001 /* NP msg code or unformatted data */ -#define LP_RNPR_TOGGLE 0x0800 /* Toggles between exchanges - * of different NP - */ -#define LP_RNPR_ACKNOWLDGE2 0x1000 /* 1 = will comply with msg - * 0 = cannot comply with msg - */ -#define LP_RNPR_MSG_PAGE 0x2000 /* formatted(1)/unformatted(0) pg */ -#define LP_RNPR_ACKNOWLDGE 0x4000 /* 1 = ACK / 0 = NO ACK */ -#define LP_RNPR_NEXT_PAGE 0x8000 /* 1 = addition NP will follow - * 0 = sending last NP - */ - -/* 1000BASE-T Control Register */ -#define CR_1000T_ASYM_PAUSE 0x0080 /* Advertise asymmetric pause bit */ -#define CR_1000T_HD_CAPS 0x0100 /* Advertise 1000T HD capability */ -#define CR_1000T_FD_CAPS 0x0200 /* Advertise 1000T FD capability */ -#define CR_1000T_REPEATER_DTE 0x0400 /* 1=Repeater/switch device port */ - /* 0=DTE device */ -#define CR_1000T_MS_VALUE 0x0800 /* 1=Configure PHY as Master */ - /* 0=Configure PHY as Slave */ -#define CR_1000T_MS_ENABLE 0x1000 /* 1=Master/Slave manual config value */ - /* 0=Automatic Master/Slave config */ -#define CR_1000T_TEST_MODE_NORMAL 0x0000 /* Normal Operation */ -#define CR_1000T_TEST_MODE_1 0x2000 /* Transmit Waveform test */ -#define CR_1000T_TEST_MODE_2 0x4000 /* Master Transmit Jitter test */ -#define CR_1000T_TEST_MODE_3 0x6000 /* Slave Transmit Jitter test */ -#define CR_1000T_TEST_MODE_4 0x8000 /* Transmitter Distortion test */ - -/* 1000BASE-T Status Register */ -#define SR_1000T_IDLE_ERROR_CNT 0x00FF /* Num idle errors since last read */ -#define SR_1000T_ASYM_PAUSE_DIR 0x0100 /* LP asymmetric pause direction bit */ -#define SR_1000T_LP_HD_CAPS 0x0400 /* LP is 1000T HD capable */ -#define SR_1000T_LP_FD_CAPS 0x0800 /* LP is 1000T FD capable */ -#define SR_1000T_REMOTE_RX_STATUS 0x1000 /* Remote receiver OK */ -#define SR_1000T_LOCAL_RX_STATUS 0x2000 /* Local receiver OK */ -#define SR_1000T_MS_CONFIG_RES 0x4000 /* 1=Local TX is Master, 0=Slave */ -#define SR_1000T_MS_CONFIG_FAULT 0x8000 /* Master/Slave config fault */ -#define SR_1000T_REMOTE_RX_STATUS_SHIFT 12 -#define SR_1000T_LOCAL_RX_STATUS_SHIFT 13 -#define SR_1000T_PHY_EXCESSIVE_IDLE_ERR_COUNT 5 -#define FFE_IDLE_ERR_COUNT_TIMEOUT_20 20 -#define FFE_IDLE_ERR_COUNT_TIMEOUT_100 100 - -/* Extended Status Register */ -#define IEEE_ESR_1000T_HD_CAPS 0x1000 /* 1000T HD capable */ -#define IEEE_ESR_1000T_FD_CAPS 0x2000 /* 1000T FD capable */ -#define IEEE_ESR_1000X_HD_CAPS 0x4000 /* 1000X HD capable */ -#define IEEE_ESR_1000X_FD_CAPS 0x8000 /* 1000X FD capable */ - -#define PHY_TX_POLARITY_MASK 0x0100 /* register 10h bit 8 (polarity bit) */ -#define PHY_TX_NORMAL_POLARITY 0 /* register 10h bit 8 (normal polarity) */ - -#define AUTO_POLARITY_DISABLE 0x0010 /* register 11h bit 4 */ - /* (0=enable, 1=disable) */ - -/* M88E1000 PHY Specific Control Register */ -#define M88E1000_PSCR_JABBER_DISABLE 0x0001 /* 1=Jabber Function disabled */ -#define M88E1000_PSCR_POLARITY_REVERSAL 0x0002 /* 1=Polarity Reversal enabled */ -#define M88E1000_PSCR_SQE_TEST 0x0004 /* 1=SQE Test enabled */ -#define M88E1000_PSCR_CLK125_DISABLE 0x0010 /* 1=CLK125 low, - * 0=CLK125 toggling - */ -#define M88E1000_PSCR_MDI_MANUAL_MODE 0x0000 /* MDI Crossover Mode bits 6:5 */ - /* Manual MDI configuration */ -#define M88E1000_PSCR_MDIX_MANUAL_MODE 0x0020 /* Manual MDIX configuration */ -#define M88E1000_PSCR_AUTO_X_1000T 0x0040 /* 1000BASE-T: Auto crossover, - * 100BASE-TX/10BASE-T: - * MDI Mode - */ -#define M88E1000_PSCR_AUTO_X_MODE 0x0060 /* Auto crossover enabled - * all speeds. - */ -#define M88E1000_PSCR_10BT_EXT_DIST_ENABLE 0x0080 - /* 1=Enable Extended 10BASE-T distance - * (Lower 10BASE-T RX Threshold) - * 0=Normal 10BASE-T RX Threshold */ -#define M88E1000_PSCR_MII_5BIT_ENABLE 0x0100 - /* 1=5-Bit interface in 100BASE-TX - * 0=MII interface in 100BASE-TX */ -#define M88E1000_PSCR_SCRAMBLER_DISABLE 0x0200 /* 1=Scrambler disable */ -#define M88E1000_PSCR_FORCE_LINK_GOOD 0x0400 /* 1=Force link good */ -#define M88E1000_PSCR_ASSERT_CRS_ON_TX 0x0800 /* 1=Assert CRS on Transmit */ - -#define M88E1000_PSCR_POLARITY_REVERSAL_SHIFT 1 -#define M88E1000_PSCR_AUTO_X_MODE_SHIFT 5 -#define M88E1000_PSCR_10BT_EXT_DIST_ENABLE_SHIFT 7 - -/* M88E1000 PHY Specific Status Register */ -#define M88E1000_PSSR_JABBER 0x0001 /* 1=Jabber */ -#define M88E1000_PSSR_REV_POLARITY 0x0002 /* 1=Polarity reversed */ -#define M88E1000_PSSR_DOWNSHIFT 0x0020 /* 1=Downshifted */ -#define M88E1000_PSSR_MDIX 0x0040 /* 1=MDIX; 0=MDI */ -#define M88E1000_PSSR_CABLE_LENGTH 0x0380 /* 0=<50M;1=50-80M;2=80-110M; - * 3=110-140M;4=>140M */ -#define M88E1000_PSSR_LINK 0x0400 /* 1=Link up, 0=Link down */ -#define M88E1000_PSSR_SPD_DPLX_RESOLVED 0x0800 /* 1=Speed & Duplex resolved */ -#define M88E1000_PSSR_PAGE_RCVD 0x1000 /* 1=Page received */ -#define M88E1000_PSSR_DPLX 0x2000 /* 1=Duplex 0=Half Duplex */ -#define M88E1000_PSSR_SPEED 0xC000 /* Speed, bits 14:15 */ -#define M88E1000_PSSR_10MBS 0x0000 /* 00=10Mbs */ -#define M88E1000_PSSR_100MBS 0x4000 /* 01=100Mbs */ -#define M88E1000_PSSR_1000MBS 0x8000 /* 10=1000Mbs */ - -#define M88E1000_PSSR_REV_POLARITY_SHIFT 1 -#define M88E1000_PSSR_DOWNSHIFT_SHIFT 5 -#define M88E1000_PSSR_MDIX_SHIFT 6 -#define M88E1000_PSSR_CABLE_LENGTH_SHIFT 7 - -/* M88E1000 Extended PHY Specific Control Register */ -#define M88E1000_EPSCR_FIBER_LOOPBACK 0x4000 /* 1=Fiber loopback */ -#define M88E1000_EPSCR_DOWN_NO_IDLE 0x8000 /* 1=Lost lock detect enabled. - * Will assert lost lock and bring - * link down if idle not seen - * within 1ms in 1000BASE-T - */ -/* Number of times we will attempt to autonegotiate before downshifting if we - * are the master */ -#define M88E1000_EPSCR_MASTER_DOWNSHIFT_MASK 0x0C00 -#define M88E1000_EPSCR_MASTER_DOWNSHIFT_1X 0x0000 -#define M88E1000_EPSCR_MASTER_DOWNSHIFT_2X 0x0400 -#define M88E1000_EPSCR_MASTER_DOWNSHIFT_3X 0x0800 -#define M88E1000_EPSCR_MASTER_DOWNSHIFT_4X 0x0C00 -/* Number of times we will attempt to autonegotiate before downshifting if we - * are the slave */ -#define M88E1000_EPSCR_SLAVE_DOWNSHIFT_MASK 0x0300 -#define M88E1000_EPSCR_SLAVE_DOWNSHIFT_DIS 0x0000 -#define M88E1000_EPSCR_SLAVE_DOWNSHIFT_1X 0x0100 -#define M88E1000_EPSCR_SLAVE_DOWNSHIFT_2X 0x0200 -#define M88E1000_EPSCR_SLAVE_DOWNSHIFT_3X 0x0300 -#define M88E1000_EPSCR_TX_CLK_2_5 0x0060 /* 2.5 MHz TX_CLK */ -#define M88E1000_EPSCR_TX_CLK_25 0x0070 /* 25 MHz TX_CLK */ -#define M88E1000_EPSCR_TX_CLK_0 0x0000 /* NO TX_CLK */ - -/* M88EC018 Rev 2 specific DownShift settings */ -#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_MASK 0x0E00 -#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_1X 0x0000 -#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_2X 0x0200 -#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_3X 0x0400 -#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_4X 0x0600 -#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_5X 0x0800 -#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_6X 0x0A00 -#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_7X 0x0C00 -#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_8X 0x0E00 - -/* IGP01E1000 Specific Port Config Register - R/W */ -#define IGP01E1000_PSCFR_AUTO_MDIX_PAR_DETECT 0x0010 -#define IGP01E1000_PSCFR_PRE_EN 0x0020 -#define IGP01E1000_PSCFR_SMART_SPEED 0x0080 -#define IGP01E1000_PSCFR_DISABLE_TPLOOPBACK 0x0100 -#define IGP01E1000_PSCFR_DISABLE_JABBER 0x0400 -#define IGP01E1000_PSCFR_DISABLE_TRANSMIT 0x2000 - -/* IGP01E1000 Specific Port Status Register - R/O */ -#define IGP01E1000_PSSR_AUTONEG_FAILED 0x0001 /* RO LH SC */ -#define IGP01E1000_PSSR_POLARITY_REVERSED 0x0002 -#define IGP01E1000_PSSR_CABLE_LENGTH 0x007C -#define IGP01E1000_PSSR_FULL_DUPLEX 0x0200 -#define IGP01E1000_PSSR_LINK_UP 0x0400 -#define IGP01E1000_PSSR_MDIX 0x0800 -#define IGP01E1000_PSSR_SPEED_MASK 0xC000 /* speed bits mask */ -#define IGP01E1000_PSSR_SPEED_10MBPS 0x4000 -#define IGP01E1000_PSSR_SPEED_100MBPS 0x8000 -#define IGP01E1000_PSSR_SPEED_1000MBPS 0xC000 -#define IGP01E1000_PSSR_CABLE_LENGTH_SHIFT 0x0002 /* shift right 2 */ -#define IGP01E1000_PSSR_MDIX_SHIFT 0x000B /* shift right 11 */ - -/* IGP01E1000 Specific Port Control Register - R/W */ -#define IGP01E1000_PSCR_TP_LOOPBACK 0x0010 -#define IGP01E1000_PSCR_CORRECT_NC_SCMBLR 0x0200 -#define IGP01E1000_PSCR_TEN_CRS_SELECT 0x0400 -#define IGP01E1000_PSCR_FLIP_CHIP 0x0800 -#define IGP01E1000_PSCR_AUTO_MDIX 0x1000 -#define IGP01E1000_PSCR_FORCE_MDI_MDIX 0x2000 /* 0-MDI, 1-MDIX */ - -/* IGP01E1000 Specific Port Link Health Register */ -#define IGP01E1000_PLHR_SS_DOWNGRADE 0x8000 -#define IGP01E1000_PLHR_GIG_SCRAMBLER_ERROR 0x4000 -#define IGP01E1000_PLHR_MASTER_FAULT 0x2000 -#define IGP01E1000_PLHR_MASTER_RESOLUTION 0x1000 -#define IGP01E1000_PLHR_GIG_REM_RCVR_NOK 0x0800 /* LH */ -#define IGP01E1000_PLHR_IDLE_ERROR_CNT_OFLOW 0x0400 /* LH */ -#define IGP01E1000_PLHR_DATA_ERR_1 0x0200 /* LH */ -#define IGP01E1000_PLHR_DATA_ERR_0 0x0100 -#define IGP01E1000_PLHR_AUTONEG_FAULT 0x0040 -#define IGP01E1000_PLHR_AUTONEG_ACTIVE 0x0010 -#define IGP01E1000_PLHR_VALID_CHANNEL_D 0x0008 -#define IGP01E1000_PLHR_VALID_CHANNEL_C 0x0004 -#define IGP01E1000_PLHR_VALID_CHANNEL_B 0x0002 -#define IGP01E1000_PLHR_VALID_CHANNEL_A 0x0001 - -/* IGP01E1000 Channel Quality Register */ -#define IGP01E1000_MSE_CHANNEL_D 0x000F -#define IGP01E1000_MSE_CHANNEL_C 0x00F0 -#define IGP01E1000_MSE_CHANNEL_B 0x0F00 -#define IGP01E1000_MSE_CHANNEL_A 0xF000 - -#define IGP02E1000_PM_SPD 0x0001 /* Smart Power Down */ -#define IGP02E1000_PM_D3_LPLU 0x0004 /* Enable LPLU in non-D0a modes */ -#define IGP02E1000_PM_D0_LPLU 0x0002 /* Enable LPLU in D0a mode */ - -/* IGP01E1000 DSP reset macros */ -#define DSP_RESET_ENABLE 0x0 -#define DSP_RESET_DISABLE 0x2 -#define E1000_MAX_DSP_RESETS 10 - -/* IGP01E1000 & IGP02E1000 AGC Registers */ - -#define IGP01E1000_AGC_LENGTH_SHIFT 7 /* Coarse - 13:11, Fine - 10:7 */ -#define IGP02E1000_AGC_LENGTH_SHIFT 9 /* Coarse - 15:13, Fine - 12:9 */ - -/* IGP02E1000 AGC Register Length 9-bit mask */ -#define IGP02E1000_AGC_LENGTH_MASK 0x7F - -/* 7 bits (3 Coarse + 4 Fine) --> 128 optional values */ -#define IGP01E1000_AGC_LENGTH_TABLE_SIZE 128 -#define IGP02E1000_AGC_LENGTH_TABLE_SIZE 113 - -/* The precision error of the cable length is +/- 10 meters */ -#define IGP01E1000_AGC_RANGE 10 -#define IGP02E1000_AGC_RANGE 15 - -/* IGP01E1000 PCS Initialization register */ -/* bits 3:6 in the PCS registers stores the channels polarity */ -#define IGP01E1000_PHY_POLARITY_MASK 0x0078 - -/* IGP01E1000 GMII FIFO Register */ -#define IGP01E1000_GMII_FLEX_SPD 0x10 /* Enable flexible speed - * on Link-Up */ -#define IGP01E1000_GMII_SPD 0x20 /* Enable SPD */ - -/* IGP01E1000 Analog Register */ -#define IGP01E1000_ANALOG_SPARE_FUSE_STATUS 0x20D1 -#define IGP01E1000_ANALOG_FUSE_STATUS 0x20D0 -#define IGP01E1000_ANALOG_FUSE_CONTROL 0x20DC -#define IGP01E1000_ANALOG_FUSE_BYPASS 0x20DE - -#define IGP01E1000_ANALOG_FUSE_POLY_MASK 0xF000 -#define IGP01E1000_ANALOG_FUSE_FINE_MASK 0x0F80 -#define IGP01E1000_ANALOG_FUSE_COARSE_MASK 0x0070 -#define IGP01E1000_ANALOG_SPARE_FUSE_ENABLED 0x0100 -#define IGP01E1000_ANALOG_FUSE_ENABLE_SW_CONTROL 0x0002 - -#define IGP01E1000_ANALOG_FUSE_COARSE_THRESH 0x0040 -#define IGP01E1000_ANALOG_FUSE_COARSE_10 0x0010 -#define IGP01E1000_ANALOG_FUSE_FINE_1 0x0080 -#define IGP01E1000_ANALOG_FUSE_FINE_10 0x0500 - -/* GG82563 PHY Specific Status Register (Page 0, Register 16 */ -#define GG82563_PSCR_DISABLE_JABBER 0x0001 /* 1=Disable Jabber */ -#define GG82563_PSCR_POLARITY_REVERSAL_DISABLE 0x0002 /* 1=Polarity Reversal Disabled */ -#define GG82563_PSCR_POWER_DOWN 0x0004 /* 1=Power Down */ -#define GG82563_PSCR_COPPER_TRANSMITER_DISABLE 0x0008 /* 1=Transmitter Disabled */ -#define GG82563_PSCR_CROSSOVER_MODE_MASK 0x0060 -#define GG82563_PSCR_CROSSOVER_MODE_MDI 0x0000 /* 00=Manual MDI configuration */ -#define GG82563_PSCR_CROSSOVER_MODE_MDIX 0x0020 /* 01=Manual MDIX configuration */ -#define GG82563_PSCR_CROSSOVER_MODE_AUTO 0x0060 /* 11=Automatic crossover */ -#define GG82563_PSCR_ENALBE_EXTENDED_DISTANCE 0x0080 /* 1=Enable Extended Distance */ -#define GG82563_PSCR_ENERGY_DETECT_MASK 0x0300 -#define GG82563_PSCR_ENERGY_DETECT_OFF 0x0000 /* 00,01=Off */ -#define GG82563_PSCR_ENERGY_DETECT_RX 0x0200 /* 10=Sense on Rx only (Energy Detect) */ -#define GG82563_PSCR_ENERGY_DETECT_RX_TM 0x0300 /* 11=Sense and Tx NLP */ -#define GG82563_PSCR_FORCE_LINK_GOOD 0x0400 /* 1=Force Link Good */ -#define GG82563_PSCR_DOWNSHIFT_ENABLE 0x0800 /* 1=Enable Downshift */ -#define GG82563_PSCR_DOWNSHIFT_COUNTER_MASK 0x7000 -#define GG82563_PSCR_DOWNSHIFT_COUNTER_SHIFT 12 - -/* PHY Specific Status Register (Page 0, Register 17) */ -#define GG82563_PSSR_JABBER 0x0001 /* 1=Jabber */ -#define GG82563_PSSR_POLARITY 0x0002 /* 1=Polarity Reversed */ -#define GG82563_PSSR_LINK 0x0008 /* 1=Link is Up */ -#define GG82563_PSSR_ENERGY_DETECT 0x0010 /* 1=Sleep, 0=Active */ -#define GG82563_PSSR_DOWNSHIFT 0x0020 /* 1=Downshift */ -#define GG82563_PSSR_CROSSOVER_STATUS 0x0040 /* 1=MDIX, 0=MDI */ -#define GG82563_PSSR_RX_PAUSE_ENABLED 0x0100 /* 1=Receive Pause Enabled */ -#define GG82563_PSSR_TX_PAUSE_ENABLED 0x0200 /* 1=Transmit Pause Enabled */ -#define GG82563_PSSR_LINK_UP 0x0400 /* 1=Link Up */ -#define GG82563_PSSR_SPEED_DUPLEX_RESOLVED 0x0800 /* 1=Resolved */ -#define GG82563_PSSR_PAGE_RECEIVED 0x1000 /* 1=Page Received */ -#define GG82563_PSSR_DUPLEX 0x2000 /* 1-Full-Duplex */ -#define GG82563_PSSR_SPEED_MASK 0xC000 -#define GG82563_PSSR_SPEED_10MBPS 0x0000 /* 00=10Mbps */ -#define GG82563_PSSR_SPEED_100MBPS 0x4000 /* 01=100Mbps */ -#define GG82563_PSSR_SPEED_1000MBPS 0x8000 /* 10=1000Mbps */ - -/* PHY Specific Status Register 2 (Page 0, Register 19) */ -#define GG82563_PSSR2_JABBER 0x0001 /* 1=Jabber */ -#define GG82563_PSSR2_POLARITY_CHANGED 0x0002 /* 1=Polarity Changed */ -#define GG82563_PSSR2_ENERGY_DETECT_CHANGED 0x0010 /* 1=Energy Detect Changed */ -#define GG82563_PSSR2_DOWNSHIFT_INTERRUPT 0x0020 /* 1=Downshift Detected */ -#define GG82563_PSSR2_MDI_CROSSOVER_CHANGE 0x0040 /* 1=Crossover Changed */ -#define GG82563_PSSR2_FALSE_CARRIER 0x0100 /* 1=False Carrier */ -#define GG82563_PSSR2_SYMBOL_ERROR 0x0200 /* 1=Symbol Error */ -#define GG82563_PSSR2_LINK_STATUS_CHANGED 0x0400 /* 1=Link Status Changed */ -#define GG82563_PSSR2_AUTO_NEG_COMPLETED 0x0800 /* 1=Auto-Neg Completed */ -#define GG82563_PSSR2_PAGE_RECEIVED 0x1000 /* 1=Page Received */ -#define GG82563_PSSR2_DUPLEX_CHANGED 0x2000 /* 1=Duplex Changed */ -#define GG82563_PSSR2_SPEED_CHANGED 0x4000 /* 1=Speed Changed */ -#define GG82563_PSSR2_AUTO_NEG_ERROR 0x8000 /* 1=Auto-Neg Error */ - -/* PHY Specific Control Register 2 (Page 0, Register 26) */ -#define GG82563_PSCR2_10BT_POLARITY_FORCE 0x0002 /* 1=Force Negative Polarity */ -#define GG82563_PSCR2_1000MB_TEST_SELECT_MASK 0x000C -#define GG82563_PSCR2_1000MB_TEST_SELECT_NORMAL 0x0000 /* 00,01=Normal Operation */ -#define GG82563_PSCR2_1000MB_TEST_SELECT_112NS 0x0008 /* 10=Select 112ns Sequence */ -#define GG82563_PSCR2_1000MB_TEST_SELECT_16NS 0x000C /* 11=Select 16ns Sequence */ -#define GG82563_PSCR2_REVERSE_AUTO_NEG 0x2000 /* 1=Reverse Auto-Negotiation */ -#define GG82563_PSCR2_1000BT_DISABLE 0x4000 /* 1=Disable 1000BASE-T */ -#define GG82563_PSCR2_TRANSMITER_TYPE_MASK 0x8000 -#define GG82563_PSCR2_TRANSMITTER_TYPE_CLASS_B 0x0000 /* 0=Class B */ -#define GG82563_PSCR2_TRANSMITTER_TYPE_CLASS_A 0x8000 /* 1=Class A */ - -/* MAC Specific Control Register (Page 2, Register 21) */ -/* Tx clock speed for Link Down and 1000BASE-T for the following speeds */ -#define GG82563_MSCR_TX_CLK_MASK 0x0007 -#define GG82563_MSCR_TX_CLK_10MBPS_2_5MHZ 0x0004 -#define GG82563_MSCR_TX_CLK_100MBPS_25MHZ 0x0005 -#define GG82563_MSCR_TX_CLK_1000MBPS_2_5MHZ 0x0006 -#define GG82563_MSCR_TX_CLK_1000MBPS_25MHZ 0x0007 - -#define GG82563_MSCR_ASSERT_CRS_ON_TX 0x0010 /* 1=Assert */ - -/* DSP Distance Register (Page 5, Register 26) */ -#define GG82563_DSPD_CABLE_LENGTH 0x0007 /* 0 = <50M; - 1 = 50-80M; - 2 = 80-110M; - 3 = 110-140M; - 4 = >140M */ - -/* Kumeran Mode Control Register (Page 193, Register 16) */ -#define GG82563_KMCR_PHY_LEDS_EN 0x0020 /* 1=PHY LEDs, 0=Kumeran Inband LEDs */ -#define GG82563_KMCR_FORCE_LINK_UP 0x0040 /* 1=Force Link Up */ -#define GG82563_KMCR_SUPPRESS_SGMII_EPD_EXT 0x0080 -#define GG82563_KMCR_MDIO_BUS_SPEED_SELECT_MASK 0x0400 -#define GG82563_KMCR_MDIO_BUS_SPEED_SELECT 0x0400 /* 1=6.25MHz, 0=0.8MHz */ -#define GG82563_KMCR_PASS_FALSE_CARRIER 0x0800 - -/* Power Management Control Register (Page 193, Register 20) */ -#define GG82563_PMCR_ENABLE_ELECTRICAL_IDLE 0x0001 /* 1=Enalbe SERDES Electrical Idle */ -#define GG82563_PMCR_DISABLE_PORT 0x0002 /* 1=Disable Port */ -#define GG82563_PMCR_DISABLE_SERDES 0x0004 /* 1=Disable SERDES */ -#define GG82563_PMCR_REVERSE_AUTO_NEG 0x0008 /* 1=Enable Reverse Auto-Negotiation */ -#define GG82563_PMCR_DISABLE_1000_NON_D0 0x0010 /* 1=Disable 1000Mbps Auto-Neg in non D0 */ -#define GG82563_PMCR_DISABLE_1000 0x0020 /* 1=Disable 1000Mbps Auto-Neg Always */ -#define GG82563_PMCR_REVERSE_AUTO_NEG_D0A 0x0040 /* 1=Enable D0a Reverse Auto-Negotiation */ -#define GG82563_PMCR_FORCE_POWER_STATE 0x0080 /* 1=Force Power State */ -#define GG82563_PMCR_PROGRAMMED_POWER_STATE_MASK 0x0300 -#define GG82563_PMCR_PROGRAMMED_POWER_STATE_DR 0x0000 /* 00=Dr */ -#define GG82563_PMCR_PROGRAMMED_POWER_STATE_D0U 0x0100 /* 01=D0u */ -#define GG82563_PMCR_PROGRAMMED_POWER_STATE_D0A 0x0200 /* 10=D0a */ -#define GG82563_PMCR_PROGRAMMED_POWER_STATE_D3 0x0300 /* 11=D3 */ - -/* In-Band Control Register (Page 194, Register 18) */ -#define GG82563_ICR_DIS_PADDING 0x0010 /* Disable Padding Use */ - - -/* Bit definitions for valid PHY IDs. */ -/* I = Integrated - * E = External - */ -#define M88_VENDOR 0x0141 -#define M88E1000_E_PHY_ID 0x01410C50 -#define M88E1000_I_PHY_ID 0x01410C30 -#define M88E1011_I_PHY_ID 0x01410C20 -#define IGP01E1000_I_PHY_ID 0x02A80380 -#define M88E1000_12_PHY_ID M88E1000_E_PHY_ID -#define M88E1000_14_PHY_ID M88E1000_E_PHY_ID -#define M88E1011_I_REV_4 0x04 -#define M88E1111_I_PHY_ID 0x01410CC0 -#define L1LXT971A_PHY_ID 0x001378E0 -#define GG82563_E_PHY_ID 0x01410CA0 - - -/* Bits... - * 15-5: page - * 4-0: register offset - */ -#define PHY_PAGE_SHIFT 5 -#define PHY_REG(page, reg) \ - (((page) << PHY_PAGE_SHIFT) | ((reg) & MAX_PHY_REG_ADDRESS)) - -#define IGP3_PHY_PORT_CTRL \ - PHY_REG(769, 17) /* Port General Configuration */ -#define IGP3_PHY_RATE_ADAPT_CTRL \ - PHY_REG(769, 25) /* Rate Adapter Control Register */ - -#define IGP3_KMRN_FIFO_CTRL_STATS \ - PHY_REG(770, 16) /* KMRN FIFO's control/status register */ -#define IGP3_KMRN_POWER_MNG_CTRL \ - PHY_REG(770, 17) /* KMRN Power Management Control Register */ -#define IGP3_KMRN_INBAND_CTRL \ - PHY_REG(770, 18) /* KMRN Inband Control Register */ -#define IGP3_KMRN_DIAG \ - PHY_REG(770, 19) /* KMRN Diagnostic register */ -#define IGP3_KMRN_DIAG_PCS_LOCK_LOSS 0x0002 /* RX PCS is not synced */ -#define IGP3_KMRN_ACK_TIMEOUT \ - PHY_REG(770, 20) /* KMRN Acknowledge Timeouts register */ - -#define IGP3_VR_CTRL \ - PHY_REG(776, 18) /* Voltage regulator control register */ -#define IGP3_VR_CTRL_MODE_SHUT 0x0200 /* Enter powerdown, shutdown VRs */ -#define IGP3_VR_CTRL_MODE_MASK 0x0300 /* Shutdown VR Mask */ - -#define IGP3_CAPABILITY \ - PHY_REG(776, 19) /* IGP3 Capability Register */ - -/* Capabilities for SKU Control */ -#define IGP3_CAP_INITIATE_TEAM 0x0001 /* Able to initiate a team */ -#define IGP3_CAP_WFM 0x0002 /* Support WoL and PXE */ -#define IGP3_CAP_ASF 0x0004 /* Support ASF */ -#define IGP3_CAP_LPLU 0x0008 /* Support Low Power Link Up */ -#define IGP3_CAP_DC_AUTO_SPEED 0x0010 /* Support AC/DC Auto Link Speed */ -#define IGP3_CAP_SPD 0x0020 /* Support Smart Power Down */ -#define IGP3_CAP_MULT_QUEUE 0x0040 /* Support 2 tx & 2 rx queues */ -#define IGP3_CAP_RSS 0x0080 /* Support RSS */ -#define IGP3_CAP_8021PQ 0x0100 /* Support 802.1Q & 802.1p */ -#define IGP3_CAP_AMT_CB 0x0200 /* Support active manageability and circuit breaker */ - -#define IGP3_PPC_JORDAN_EN 0x0001 -#define IGP3_PPC_JORDAN_GIGA_SPEED 0x0002 - -#define IGP3_KMRN_PMC_EE_IDLE_LINK_DIS 0x0001 -#define IGP3_KMRN_PMC_K0S_ENTRY_LATENCY_MASK 0x001E -#define IGP3_KMRN_PMC_K0S_MODE1_EN_GIGA 0x0020 -#define IGP3_KMRN_PMC_K0S_MODE1_EN_100 0x0040 - -#define IGP3E1000_PHY_MISC_CTRL 0x1B /* Misc. Ctrl register */ -#define IGP3_PHY_MISC_DUPLEX_MANUAL_SET 0x1000 /* Duplex Manual Set */ - -#define IGP3_KMRN_EXT_CTRL PHY_REG(770, 18) -#define IGP3_KMRN_EC_DIS_INBAND 0x0080 - -#define IGP03E1000_E_PHY_ID 0x02A80390 -#define IFE_E_PHY_ID 0x02A80330 /* 10/100 PHY */ -#define IFE_PLUS_E_PHY_ID 0x02A80320 -#define IFE_C_E_PHY_ID 0x02A80310 - -#define IFE_PHY_EXTENDED_STATUS_CONTROL 0x10 /* 100BaseTx Extended Status, Control and Address */ -#define IFE_PHY_SPECIAL_CONTROL 0x11 /* 100BaseTx PHY special control register */ -#define IFE_PHY_RCV_FALSE_CARRIER 0x13 /* 100BaseTx Receive False Carrier Counter */ -#define IFE_PHY_RCV_DISCONNECT 0x14 /* 100BaseTx Receive Disconnet Counter */ -#define IFE_PHY_RCV_ERROT_FRAME 0x15 /* 100BaseTx Receive Error Frame Counter */ -#define IFE_PHY_RCV_SYMBOL_ERR 0x16 /* Receive Symbol Error Counter */ -#define IFE_PHY_PREM_EOF_ERR 0x17 /* 100BaseTx Receive Premature End Of Frame Error Counter */ -#define IFE_PHY_RCV_EOF_ERR 0x18 /* 10BaseT Receive End Of Frame Error Counter */ -#define IFE_PHY_TX_JABBER_DETECT 0x19 /* 10BaseT Transmit Jabber Detect Counter */ -#define IFE_PHY_EQUALIZER 0x1A /* PHY Equalizer Control and Status */ -#define IFE_PHY_SPECIAL_CONTROL_LED 0x1B /* PHY special control and LED configuration */ -#define IFE_PHY_MDIX_CONTROL 0x1C /* MDI/MDI-X Control register */ -#define IFE_PHY_HWI_CONTROL 0x1D /* Hardware Integrity Control (HWI) */ - -#define IFE_PESC_REDUCED_POWER_DOWN_DISABLE 0x2000 /* Defaut 1 = Disable auto reduced power down */ -#define IFE_PESC_100BTX_POWER_DOWN 0x0400 /* Indicates the power state of 100BASE-TX */ -#define IFE_PESC_10BTX_POWER_DOWN 0x0200 /* Indicates the power state of 10BASE-T */ -#define IFE_PESC_POLARITY_REVERSED 0x0100 /* Indicates 10BASE-T polarity */ -#define IFE_PESC_PHY_ADDR_MASK 0x007C /* Bit 6:2 for sampled PHY address */ -#define IFE_PESC_SPEED 0x0002 /* Auto-negotiation speed result 1=100Mbs, 0=10Mbs */ -#define IFE_PESC_DUPLEX 0x0001 /* Auto-negotiation duplex result 1=Full, 0=Half */ -#define IFE_PESC_POLARITY_REVERSED_SHIFT 8 - -#define IFE_PSC_DISABLE_DYNAMIC_POWER_DOWN 0x0100 /* 1 = Dyanmic Power Down disabled */ -#define IFE_PSC_FORCE_POLARITY 0x0020 /* 1=Reversed Polarity, 0=Normal */ -#define IFE_PSC_AUTO_POLARITY_DISABLE 0x0010 /* 1=Auto Polarity Disabled, 0=Enabled */ -#define IFE_PSC_JABBER_FUNC_DISABLE 0x0001 /* 1=Jabber Disabled, 0=Normal Jabber Operation */ -#define IFE_PSC_FORCE_POLARITY_SHIFT 5 -#define IFE_PSC_AUTO_POLARITY_DISABLE_SHIFT 4 - -#define IFE_PMC_AUTO_MDIX 0x0080 /* 1=enable MDI/MDI-X feature, default 0=disabled */ -#define IFE_PMC_FORCE_MDIX 0x0040 /* 1=force MDIX-X, 0=force MDI */ -#define IFE_PMC_MDIX_STATUS 0x0020 /* 1=MDI-X, 0=MDI */ -#define IFE_PMC_AUTO_MDIX_COMPLETE 0x0010 /* Resolution algorthm is completed */ -#define IFE_PMC_MDIX_MODE_SHIFT 6 -#define IFE_PHC_MDIX_RESET_ALL_MASK 0x0000 /* Disable auto MDI-X */ - -#define IFE_PHC_HWI_ENABLE 0x8000 /* Enable the HWI feature */ -#define IFE_PHC_ABILITY_CHECK 0x4000 /* 1= Test Passed, 0=failed */ -#define IFE_PHC_TEST_EXEC 0x2000 /* PHY launch test pulses on the wire */ -#define IFE_PHC_HIGHZ 0x0200 /* 1 = Open Circuit */ -#define IFE_PHC_LOWZ 0x0400 /* 1 = Short Circuit */ -#define IFE_PHC_LOW_HIGH_Z_MASK 0x0600 /* Mask for indication type of problem on the line */ -#define IFE_PHC_DISTANCE_MASK 0x01FF /* Mask for distance to the cable problem, in 80cm granularity */ -#define IFE_PHC_RESET_ALL_MASK 0x0000 /* Disable HWI */ -#define IFE_PSCL_PROBE_MODE 0x0020 /* LED Probe mode */ -#define IFE_PSCL_PROBE_LEDS_OFF 0x0006 /* Force LEDs 0 and 2 off */ -#define IFE_PSCL_PROBE_LEDS_ON 0x0007 /* Force LEDs 0 and 2 on */ - -#define ICH_FLASH_COMMAND_TIMEOUT 5000 /* 5000 uSecs - adjusted */ -#define ICH_FLASH_ERASE_TIMEOUT 3000000 /* Up to 3 seconds - worst case */ -#define ICH_FLASH_CYCLE_REPEAT_COUNT 10 /* 10 cycles */ -#define ICH_FLASH_SEG_SIZE_256 256 -#define ICH_FLASH_SEG_SIZE_4K 4096 -#define ICH_FLASH_SEG_SIZE_8K 8192 -#define ICH_FLASH_SEG_SIZE_64K 65536 - -#define ICH_CYCLE_READ 0x0 -#define ICH_CYCLE_RESERVED 0x1 -#define ICH_CYCLE_WRITE 0x2 -#define ICH_CYCLE_ERASE 0x3 - -#define ICH_FLASH_GFPREG 0x0000 -#define ICH_FLASH_HSFSTS 0x0004 -#define ICH_FLASH_HSFCTL 0x0006 -#define ICH_FLASH_FADDR 0x0008 -#define ICH_FLASH_FDATA0 0x0010 -#define ICH_FLASH_FRACC 0x0050 -#define ICH_FLASH_FREG0 0x0054 -#define ICH_FLASH_FREG1 0x0058 -#define ICH_FLASH_FREG2 0x005C -#define ICH_FLASH_FREG3 0x0060 -#define ICH_FLASH_FPR0 0x0074 -#define ICH_FLASH_FPR1 0x0078 -#define ICH_FLASH_SSFSTS 0x0090 -#define ICH_FLASH_SSFCTL 0x0092 -#define ICH_FLASH_PREOP 0x0094 -#define ICH_FLASH_OPTYPE 0x0096 -#define ICH_FLASH_OPMENU 0x0098 - -#define ICH_FLASH_REG_MAPSIZE 0x00A0 -#define ICH_FLASH_SECTOR_SIZE 4096 -#define ICH_GFPREG_BASE_MASK 0x1FFF -#define ICH_FLASH_LINEAR_ADDR_MASK 0x00FFFFFF -#define ICH_FLAGH_SECT_ADDR_SHIFT 12 - -/* ICH8 GbE Flash Hardware Sequencing Flash Status Register bit breakdown */ -/* Offset 04h HSFSTS */ -union ich8_hws_flash_status { - struct ich8_hsfsts { - uint16_t flcdone :1; /* bit 0 Flash Cycle Done */ - uint16_t flcerr :1; /* bit 1 Flash Cycle Error */ - uint16_t dael :1; /* bit 2 Direct Access error Log */ - uint16_t berasesz :2; /* bit 4:3 Block/Sector Erase Size */ - uint16_t flcinprog :1; /* bit 5 flash SPI cycle in Progress */ - uint16_t reserved1 :2; /* bit 13:6 Reserved */ - uint16_t reserved2 :6; /* bit 13:6 Reserved */ - uint16_t fldesvalid :1; /* bit 14 Flash Descriptor Valid */ - uint16_t flockdn :1; /* bit 15 Flash Configuration Lock-Down */ - } hsf_status; - uint16_t regval; -}; - -/* ICH8 GbE Flash Hardware Sequencing Flash control Register bit breakdown */ -/* Offset 06h FLCTL */ -union ich8_hws_flash_ctrl { - struct ich8_hsflctl { - uint16_t flcgo :1; /* 0 Flash Cycle Go */ - uint16_t flcycle :2; /* 2:1 Flash Cycle */ - uint16_t reserved :5; /* 7:3 Reserved */ - uint16_t fldbcount :2; /* 9:8 Flash Data Byte Count */ - uint16_t flockdn :6; /* 15:10 Reserved */ - } hsf_ctrl; - uint16_t regval; -}; - -/* ICH8 Flash Region Access Permissions */ -union ich8_hws_flash_regacc { - struct ich8_flracc { - uint32_t grra :8; /* 0:7 GbE region Read Access */ - uint32_t grwa :8; /* 8:15 GbE region Write Access */ - uint32_t gmrag :8; /* 23:16 GbE Master Read Access Grant */ - uint32_t gmwag :8; /* 31:24 GbE Master Write Access Grant */ - } hsf_flregacc; - uint16_t regval; -}; - -/* Miscellaneous PHY bit definitions. */ -#define PHY_PREAMBLE 0xFFFFFFFF -#define PHY_SOF 0x01 -#define PHY_OP_READ 0x02 -#define PHY_OP_WRITE 0x01 -#define PHY_TURNAROUND 0x02 -#define PHY_PREAMBLE_SIZE 32 -#define MII_CR_SPEED_1000 0x0040 -#define MII_CR_SPEED_100 0x2000 -#define MII_CR_SPEED_10 0x0000 -#define E1000_PHY_ADDRESS 0x01 -#define PHY_AUTO_NEG_TIME 45 /* 4.5 Seconds */ -#define PHY_FORCE_TIME 20 /* 2.0 Seconds */ -#define PHY_REVISION_MASK 0xFFFFFFF0 -#define DEVICE_SPEED_MASK 0x00000300 /* Device Ctrl Reg Speed Mask */ -#define REG4_SPEED_MASK 0x01E0 -#define REG9_SPEED_MASK 0x0300 -#define ADVERTISE_10_HALF 0x0001 -#define ADVERTISE_10_FULL 0x0002 -#define ADVERTISE_100_HALF 0x0004 -#define ADVERTISE_100_FULL 0x0008 -#define ADVERTISE_1000_HALF 0x0010 -#define ADVERTISE_1000_FULL 0x0020 -#define AUTONEG_ADVERTISE_SPEED_DEFAULT 0x002F /* Everything but 1000-Half */ -#define AUTONEG_ADVERTISE_10_100_ALL 0x000F /* All 10/100 speeds*/ -#define AUTONEG_ADVERTISE_10_ALL 0x0003 /* 10Mbps Full & Half speeds*/ - -#endif /* _EM_HW_H_ */ diff --git a/sys/dev/netif/em/if_em_osdep.h b/sys/dev/netif/em/if_em_osdep.h deleted file mode 100644 index 812a5b1cc4..0000000000 --- a/sys/dev/netif/em/if_em_osdep.h +++ /dev/null @@ -1,171 +0,0 @@ -/************************************************************************** - -Copyright (c) 2001-2006, Intel Corporation -All rights reserved. - -Redistribution and use in source and binary forms, with or without -modification, are permitted provided that the following conditions are met: - - 1. Redistributions of source code must retain the above copyright notice, - this list of conditions and the following disclaimer. - - 2. Redistributions in binary form must reproduce the above copyright - notice, this list of conditions and the following disclaimer in the - documentation and/or other materials provided with the distribution. - - 3. Neither the name of the Intel Corporation nor the names of its - contributors may be used to endorse or promote products derived from - this software without specific prior written permission. - -THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" -AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE -IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE -ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE -LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR -CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF -SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS -INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN -CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) -ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE -POSSIBILITY OF SUCH DAMAGE. - -***************************************************************************/ - -/*$FreeBSD: src/sys/dev/em/if_em_osdep.h,v 1.1.2.11 2003/06/09 21:43:41 pdeuskar Exp $*/ -/*$DragonFly: src/sys/dev/netif/em/if_em_osdep.h,v 1.9 2006/12/23 10:39:16 sephe Exp $*/ - -#ifndef _FREEBSD_OS_H_ -#define _FREEBSD_OS_H_ - -#include -#include -#include -#include -#include -#include -#include -#include -#include - -#include -#include - -#include - -#include -#include - -#define ASSERT(x) if(!(x)) panic("EM: x") - -/* The happy-fun DELAY macro is defined in /usr/src/sys/i386/include/clock.h */ -#define usec_delay(x) DELAY(x) -#define msec_delay(x) DELAY(1000*(x)) -/* TODO: Should we be paranoid about delaying in interrupt context? */ -#define msec_delay_irq(x) DELAY(1000*(x)) - -#define MSGOUT(S, A, B) kprintf(S "\n", A, B) -#define DEBUGFUNC(F) DEBUGOUT(F); -#if DBG - #define DEBUGOUT(S) kprintf(S "\n") - #define DEBUGOUT1(S,A) kprintf(S "\n",A) - #define DEBUGOUT2(S,A,B) kprintf(S "\n",A,B) - #define DEBUGOUT3(S,A,B,C) kprintf(S "\n",A,B,C) - #define DEBUGOUT7(S,A,B,C,D,E,F,G) kprintf(S "\n",A,B,C,D,E,F,G) -#else - #define DEBUGOUT(S) - #define DEBUGOUT1(S,A) - #define DEBUGOUT2(S,A,B) - #define DEBUGOUT3(S,A,B,C) - #define DEBUGOUT7(S,A,B,C,D,E,F,G) -#endif - -#define FALSE 0 -#define TRUE 1 -#define CMD_MEM_WRT_INVALIDATE 0x0010 /* BIT_4 */ -#define PCI_COMMAND_REGISTER PCIR_COMMAND - -struct em_osdep -{ - bus_space_tag_t mem_bus_space_tag; - bus_space_handle_t mem_bus_space_handle; - bus_space_tag_t io_bus_space_tag; - bus_space_handle_t io_bus_space_handle; - bus_space_tag_t flash_bus_space_tag; - bus_space_handle_t flash_bus_space_handle; - struct device *dev; -}; - -#define E1000_WRITE_FLUSH(a) E1000_READ_REG(a, STATUS) - -/* Read from an absolute offset in the adapter's memory space */ -#define E1000_READ_OFFSET(hw, offset) \ - bus_space_read_4(((struct em_osdep *)(hw)->back)->mem_bus_space_tag, \ - ((struct em_osdep *)(hw)->back)->mem_bus_space_handle, offset) - -/* Write to an absolute offset in the adapter's memory space */ -#define E1000_WRITE_OFFSET(hw, offset, value) \ - bus_space_write_4(((struct em_osdep *)(hw)->back)->mem_bus_space_tag, \ - ((struct em_osdep *)(hw)->back)->mem_bus_space_handle, offset, value) - -/* Convert a register name to its offset in the adapter's memory space */ -#define E1000_REG_OFFSET(hw, reg) \ - ((hw)->mac_type >= em_82543 ? E1000_##reg : E1000_82542_##reg) - -/* Register READ/WRITE macros */ - -#define E1000_READ_REG(hw, reg) \ - bus_space_read_4(((struct em_osdep *)(hw)->back)->mem_bus_space_tag, \ - ((struct em_osdep *)(hw)->back)->mem_bus_space_handle, \ - ((hw)->mac_type >= em_82543 ? E1000_##reg : E1000_82542_##reg)) - -#define E1000_WRITE_REG(hw, reg, value) \ - bus_space_write_4(((struct em_osdep *)(hw)->back)->mem_bus_space_tag, \ - ((struct em_osdep *)(hw)->back)->mem_bus_space_handle, \ - ((hw)->mac_type >= em_82543 ? E1000_##reg : E1000_82542_##reg), \ - value) - -#define E1000_READ_REG_ARRAY(hw, reg, index) \ - bus_space_read_4(((struct em_osdep *)(hw)->back)->mem_bus_space_tag, \ - ((struct em_osdep *)(hw)->back)->mem_bus_space_handle, \ - ((hw)->mac_type >= em_82543 ? E1000_##reg : E1000_82542_##reg) \ - + ((index) << 2)) - -#define E1000_WRITE_REG_ARRAY(hw, reg, index, value) \ - bus_space_write_4(((struct em_osdep *)(hw)->back)->mem_bus_space_tag, \ - ((struct em_osdep *)(hw)->back)->mem_bus_space_handle, \ - ((hw)->mac_type >= em_82543 ? E1000_##reg : E1000_82542_##reg) \ - + ((index) << 2), value) - -#define E1000_READ_REG_ARRAY_DWORD E1000_READ_REG_ARRAY -#define E1000_WRITE_REG_ARRAY_DWORD E1000_WRITE_REG_ARRAY - -#define E1000_WRITE_REG_ARRAY_BYTE(hw, reg, index, value) \ - bus_space_write_1( ((struct em_osdep *)(hw)->back)->mem_bus_space_tag, \ - ((struct em_osdep *)(hw)->back)->mem_bus_space_handle, \ - ((hw)->mac_type >= em_82543 ? E1000_##reg : E1000_82542_##reg \ - + index), value) - -#define E1000_WRITE_REG_ARRAY_WORD(hw, reg, index, value) \ - bus_space_write_2( ((struct em_osdep *)(hw)->back)->mem_bus_space_tag, \ - ((struct em_osdep *)(hw)->back)->mem_bus_space_handle, \ - ((hw)->mac_type >= em_82543 ? E1000_##reg : E1000_82542_##reg \ - + (index << 1)), value) - -#define E1000_READ_ICH_FLASH_REG(hw, reg) \ - bus_space_read_4(((struct em_osdep *)(hw)->back)->flash_bus_space_tag, \ - ((struct em_osdep *)(hw)->back)->flash_bus_space_handle, reg) - -#define E1000_READ_ICH_FLASH_REG16(hw, reg) \ - bus_space_read_2(((struct em_osdep *)(hw)->back)->flash_bus_space_tag, \ - ((struct em_osdep *)(hw)->back)->flash_bus_space_handle, reg) - -#define E1000_WRITE_ICH_FLASH_REG(hw, reg, value) \ - bus_space_write_4(((struct em_osdep *)(hw)->back)->flash_bus_space_tag, \ - ((struct em_osdep *)(hw)->back)->flash_bus_space_handle, reg, value) - -#define E1000_WRITE_ICH_FLASH_REG16(hw, reg, value) \ - bus_space_write_2(((struct em_osdep *)(hw)->back)->flash_bus_space_tag, \ - ((struct em_osdep *)(hw)->back)->flash_bus_space_handle, reg, value) - -#endif /* _FREEBSD_OS_H_ */ - diff --git a/sys/dev/netif/ig_hal/LICENSE b/sys/dev/netif/ig_hal/LICENSE new file mode 100644 index 0000000000..ca4325776e --- /dev/null +++ b/sys/dev/netif/ig_hal/LICENSE @@ -0,0 +1,30 @@ + + Copyright (c) 2001-2008, Intel Corporation + All rights reserved. + + Redistribution and use in source and binary forms, with or without + modification, are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, + this list of conditions and the following disclaimer. + + 2. Redistributions in binary form must reproduce the above copyright + notice, this list of conditions and the following disclaimer in the + documentation and/or other materials provided with the distribution. + + 3. Neither the name of the Intel Corporation nor the names of its + contributors may be used to endorse or promote products derived from + this software without specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE + ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE + LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR + CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF + SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS + INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN + CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) + ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + POSSIBILITY OF SUCH DAMAGE. + diff --git a/sys/dev/netif/ig_hal/Makefile b/sys/dev/netif/ig_hal/Makefile new file mode 100644 index 0000000000..0da1d96029 --- /dev/null +++ b/sys/dev/netif/ig_hal/Makefile @@ -0,0 +1,8 @@ +KMOD = ig_hal +SRCS = device_if.h pci_if.h bus_if.h +SRCS += e1000_osdep.c +SRCS += e1000_api.c e1000_mac.c e1000_manage.c e1000_nvm.c e1000_phy.c +SRCS += e1000_80003es2lan.c e1000_82540.c e1000_82541.c e1000_82542.c \ + e1000_82543.c e1000_82571.c e1000_82575.c e1000_ich8lan.c + +.include diff --git a/sys/dev/netif/ig_hal/e1000_80003es2lan.c b/sys/dev/netif/ig_hal/e1000_80003es2lan.c new file mode 100644 index 0000000000..fa7272e579 --- /dev/null +++ b/sys/dev/netif/ig_hal/e1000_80003es2lan.c @@ -0,0 +1,1533 @@ +/****************************************************************************** + + Copyright (c) 2001-2008, Intel Corporation + All rights reserved. + + Redistribution and use in source and binary forms, with or without + modification, are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, + this list of conditions and the following disclaimer. + + 2. Redistributions in binary form must reproduce the above copyright + notice, this list of conditions and the following disclaimer in the + documentation and/or other materials provided with the distribution. + + 3. Neither the name of the Intel Corporation nor the names of its + contributors may be used to endorse or promote products derived from + this software without specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE + ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE + LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR + CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF + SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS + INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN + CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) + ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + POSSIBILITY OF SUCH DAMAGE. + +******************************************************************************/ +/*$FreeBSD$*/ + +/* + * 80003ES2LAN Gigabit Ethernet Controller (Copper) + * 80003ES2LAN Gigabit Ethernet Controller (Serdes) + */ + +#include "e1000_api.h" + +static s32 e1000_init_phy_params_80003es2lan(struct e1000_hw *hw); +static s32 e1000_init_nvm_params_80003es2lan(struct e1000_hw *hw); +static s32 e1000_init_mac_params_80003es2lan(struct e1000_hw *hw); +static s32 e1000_acquire_phy_80003es2lan(struct e1000_hw *hw); +static s32 e1000_acquire_mac_csr_80003es2lan(struct e1000_hw *hw); +static void e1000_release_phy_80003es2lan(struct e1000_hw *hw); +static void e1000_release_mac_csr_80003es2lan(struct e1000_hw *hw); +static s32 e1000_acquire_nvm_80003es2lan(struct e1000_hw *hw); +static void e1000_release_nvm_80003es2lan(struct e1000_hw *hw); +static s32 e1000_read_phy_reg_gg82563_80003es2lan(struct e1000_hw *hw, + u32 offset, + u16 *data); +static s32 e1000_write_phy_reg_gg82563_80003es2lan(struct e1000_hw *hw, + u32 offset, + u16 data); +static s32 e1000_write_nvm_80003es2lan(struct e1000_hw *hw, u16 offset, + u16 words, u16 *data); +static s32 e1000_get_cfg_done_80003es2lan(struct e1000_hw *hw); +static s32 e1000_phy_force_speed_duplex_80003es2lan(struct e1000_hw *hw); +static s32 e1000_get_cable_length_80003es2lan(struct e1000_hw *hw); +static s32 e1000_get_link_up_info_80003es2lan(struct e1000_hw *hw, u16 *speed, + u16 *duplex); +static s32 e1000_reset_hw_80003es2lan(struct e1000_hw *hw); +static s32 e1000_init_hw_80003es2lan(struct e1000_hw *hw); +static s32 e1000_setup_copper_link_80003es2lan(struct e1000_hw *hw); +static void e1000_clear_hw_cntrs_80003es2lan(struct e1000_hw *hw); +static s32 e1000_acquire_swfw_sync_80003es2lan(struct e1000_hw *hw, u16 mask); +static s32 e1000_cfg_kmrn_10_100_80003es2lan(struct e1000_hw *hw, u16 duplex); +static s32 e1000_cfg_kmrn_1000_80003es2lan(struct e1000_hw *hw); +static s32 e1000_cfg_on_link_up_80003es2lan(struct e1000_hw *hw); +static s32 e1000_read_kmrn_reg_80003es2lan(struct e1000_hw *hw, u32 offset, + u16 *data); +static s32 e1000_write_kmrn_reg_80003es2lan(struct e1000_hw *hw, u32 offset, + u16 data); +static s32 e1000_copper_link_setup_gg82563_80003es2lan(struct e1000_hw *hw); +static void e1000_initialize_hw_bits_80003es2lan(struct e1000_hw *hw); +static void e1000_release_swfw_sync_80003es2lan(struct e1000_hw *hw, u16 mask); +static s32 e1000_read_mac_addr_80003es2lan(struct e1000_hw *hw); +static void e1000_power_down_phy_copper_80003es2lan(struct e1000_hw *hw); + +/* + * A table for the GG82563 cable length where the range is defined + * with a lower bound at "index" and the upper bound at + * "index + 5". + */ +static const u16 e1000_gg82563_cable_length_table[] = + { 0, 60, 115, 150, 150, 60, 115, 150, 180, 180, 0xFF }; +#define GG82563_CABLE_LENGTH_TABLE_SIZE \ + (sizeof(e1000_gg82563_cable_length_table) / \ + sizeof(e1000_gg82563_cable_length_table[0])) + +/** + * e1000_init_phy_params_80003es2lan - Init ESB2 PHY func ptrs. + * @hw: pointer to the HW structure + **/ +static s32 e1000_init_phy_params_80003es2lan(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val = E1000_SUCCESS; + + DEBUGFUNC("e1000_init_phy_params_80003es2lan"); + + if (hw->phy.media_type != e1000_media_type_copper) { + phy->type = e1000_phy_none; + goto out; + } else { + phy->ops.power_up = e1000_power_up_phy_copper; + phy->ops.power_down = e1000_power_down_phy_copper_80003es2lan; + } + + phy->addr = 1; + phy->autoneg_mask = AUTONEG_ADVERTISE_SPEED_DEFAULT; + phy->reset_delay_us = 100; + phy->type = e1000_phy_gg82563; + + phy->ops.acquire = e1000_acquire_phy_80003es2lan; + phy->ops.check_polarity = e1000_check_polarity_m88; + phy->ops.check_reset_block = e1000_check_reset_block_generic; + phy->ops.commit = e1000_phy_sw_reset_generic; + phy->ops.get_cfg_done = e1000_get_cfg_done_80003es2lan; + phy->ops.get_info = e1000_get_phy_info_m88; + phy->ops.release = e1000_release_phy_80003es2lan; + phy->ops.reset = e1000_phy_hw_reset_generic; + phy->ops.set_d3_lplu_state = e1000_set_d3_lplu_state_generic; + + phy->ops.force_speed_duplex = e1000_phy_force_speed_duplex_80003es2lan; + phy->ops.get_cable_length = e1000_get_cable_length_80003es2lan; + phy->ops.read_reg = e1000_read_phy_reg_gg82563_80003es2lan; + phy->ops.write_reg = e1000_write_phy_reg_gg82563_80003es2lan; + + phy->ops.cfg_on_link_up = e1000_cfg_on_link_up_80003es2lan; + + /* This can only be done after all function pointers are setup. */ + ret_val = e1000_get_phy_id(hw); + + /* Verify phy id */ + if (phy->id != GG82563_E_PHY_ID) { + ret_val = -E1000_ERR_PHY; + goto out; + } + +out: + return ret_val; +} + +/** + * e1000_init_nvm_params_80003es2lan - Init ESB2 NVM func ptrs. + * @hw: pointer to the HW structure + **/ +static s32 e1000_init_nvm_params_80003es2lan(struct e1000_hw *hw) +{ + struct e1000_nvm_info *nvm = &hw->nvm; + u32 eecd = E1000_READ_REG(hw, E1000_EECD); + u16 size; + + DEBUGFUNC("e1000_init_nvm_params_80003es2lan"); + + nvm->opcode_bits = 8; + nvm->delay_usec = 1; + switch (nvm->override) { + case e1000_nvm_override_spi_large: + nvm->page_size = 32; + nvm->address_bits = 16; + break; + case e1000_nvm_override_spi_small: + nvm->page_size = 8; + nvm->address_bits = 8; + break; + default: + nvm->page_size = eecd & E1000_EECD_ADDR_BITS ? 32 : 8; + nvm->address_bits = eecd & E1000_EECD_ADDR_BITS ? 16 : 8; + break; + } + + nvm->type = e1000_nvm_eeprom_spi; + + size = (u16)((eecd & E1000_EECD_SIZE_EX_MASK) >> + E1000_EECD_SIZE_EX_SHIFT); + + /* + * Added to a constant, "size" becomes the left-shift value + * for setting word_size. + */ + size += NVM_WORD_SIZE_BASE_SHIFT; + + /* EEPROM access above 16k is unsupported */ + if (size > 14) + size = 14; + nvm->word_size = 1 << size; + + /* Function Pointers */ + nvm->ops.acquire = e1000_acquire_nvm_80003es2lan; + nvm->ops.read = e1000_read_nvm_eerd; + nvm->ops.release = e1000_release_nvm_80003es2lan; + nvm->ops.update = e1000_update_nvm_checksum_generic; + nvm->ops.valid_led_default = e1000_valid_led_default_generic; + nvm->ops.validate = e1000_validate_nvm_checksum_generic; + nvm->ops.write = e1000_write_nvm_80003es2lan; + + return E1000_SUCCESS; +} + +/** + * e1000_init_mac_params_80003es2lan - Init ESB2 MAC func ptrs. + * @hw: pointer to the HW structure + **/ +static s32 e1000_init_mac_params_80003es2lan(struct e1000_hw *hw) +{ + struct e1000_mac_info *mac = &hw->mac; + s32 ret_val = E1000_SUCCESS; + + DEBUGFUNC("e1000_init_mac_params_80003es2lan"); + + /* Set media type */ + switch (hw->device_id) { + case E1000_DEV_ID_80003ES2LAN_SERDES_DPT: + hw->phy.media_type = e1000_media_type_internal_serdes; + break; + default: + hw->phy.media_type = e1000_media_type_copper; + break; + } + + /* Set mta register count */ + mac->mta_reg_count = 128; + /* Set rar entry count */ + mac->rar_entry_count = E1000_RAR_ENTRIES; + /* Set if part includes ASF firmware */ + mac->asf_firmware_present = TRUE; + /* Set if manageability features are enabled. */ + mac->arc_subsystem_valid = + (E1000_READ_REG(hw, E1000_FWSM) & E1000_FWSM_MODE_MASK) + ? TRUE : FALSE; + + /* Function pointers */ + + /* bus type/speed/width */ + mac->ops.get_bus_info = e1000_get_bus_info_pcie_generic; + /* reset */ + mac->ops.reset_hw = e1000_reset_hw_80003es2lan; + /* hw initialization */ + mac->ops.init_hw = e1000_init_hw_80003es2lan; + /* link setup */ + mac->ops.setup_link = e1000_setup_link_generic; + /* physical interface link setup */ + mac->ops.setup_physical_interface = + (hw->phy.media_type == e1000_media_type_copper) + ? e1000_setup_copper_link_80003es2lan + : e1000_setup_fiber_serdes_link_generic; + /* check for link */ + switch (hw->phy.media_type) { + case e1000_media_type_copper: + mac->ops.check_for_link = e1000_check_for_copper_link_generic; + break; + case e1000_media_type_fiber: + mac->ops.check_for_link = e1000_check_for_fiber_link_generic; + break; + case e1000_media_type_internal_serdes: + mac->ops.check_for_link = e1000_check_for_serdes_link_generic; + break; + default: + ret_val = -E1000_ERR_CONFIG; + goto out; + break; + } + /* check management mode */ + mac->ops.check_mng_mode = e1000_check_mng_mode_generic; + /* multicast address update */ + mac->ops.update_mc_addr_list = e1000_update_mc_addr_list_generic; + /* writing VFTA */ + mac->ops.write_vfta = e1000_write_vfta_generic; + /* clearing VFTA */ + mac->ops.clear_vfta = e1000_clear_vfta_generic; + /* setting MTA */ + mac->ops.mta_set = e1000_mta_set_generic; + /* read mac address */ + mac->ops.read_mac_addr = e1000_read_mac_addr_80003es2lan; + /* blink LED */ + mac->ops.blink_led = e1000_blink_led_generic; + /* setup LED */ + mac->ops.setup_led = e1000_setup_led_generic; + /* cleanup LED */ + mac->ops.cleanup_led = e1000_cleanup_led_generic; + /* turn on/off LED */ + mac->ops.led_on = e1000_led_on_generic; + mac->ops.led_off = e1000_led_off_generic; + /* clear hardware counters */ + mac->ops.clear_hw_cntrs = e1000_clear_hw_cntrs_80003es2lan; + /* link info */ + mac->ops.get_link_up_info = e1000_get_link_up_info_80003es2lan; + +out: + return ret_val; +} + +/** + * e1000_init_function_pointers_80003es2lan - Init ESB2 func ptrs. + * @hw: pointer to the HW structure + * + * Called to initialize all function pointers and parameters. + **/ +void e1000_init_function_pointers_80003es2lan(struct e1000_hw *hw) +{ + DEBUGFUNC("e1000_init_function_pointers_80003es2lan"); + + hw->mac.ops.init_params = e1000_init_mac_params_80003es2lan; + hw->nvm.ops.init_params = e1000_init_nvm_params_80003es2lan; + hw->phy.ops.init_params = e1000_init_phy_params_80003es2lan; + e1000_get_bus_info_pcie_generic(hw); +} + +/** + * e1000_acquire_phy_80003es2lan - Acquire rights to access PHY + * @hw: pointer to the HW structure + * + * A wrapper to acquire access rights to the correct PHY. + **/ +static s32 e1000_acquire_phy_80003es2lan(struct e1000_hw *hw) +{ + u16 mask; + + DEBUGFUNC("e1000_acquire_phy_80003es2lan"); + + mask = hw->bus.func ? E1000_SWFW_PHY1_SM : E1000_SWFW_PHY0_SM; + return e1000_acquire_swfw_sync_80003es2lan(hw, mask); +} + +/** + * e1000_release_phy_80003es2lan - Release rights to access PHY + * @hw: pointer to the HW structure + * + * A wrapper to release access rights to the correct PHY. + **/ +static void e1000_release_phy_80003es2lan(struct e1000_hw *hw) +{ + u16 mask; + + DEBUGFUNC("e1000_release_phy_80003es2lan"); + + mask = hw->bus.func ? E1000_SWFW_PHY1_SM : E1000_SWFW_PHY0_SM; + e1000_release_swfw_sync_80003es2lan(hw, mask); +} + + +/** + * e1000_acquire_mac_csr_80003es2lan - Acquire rights to access Kumeran register + * @hw: pointer to the HW structure + * + * Acquire the semaphore to access the Kumeran interface. + * + **/ +static s32 e1000_acquire_mac_csr_80003es2lan(struct e1000_hw *hw) +{ + u16 mask; + + DEBUGFUNC("e1000_acquire_mac_csr_80003es2lan"); + + mask = E1000_SWFW_CSR_SM; + + return e1000_acquire_swfw_sync_80003es2lan(hw, mask); +} + +/** + * e1000_release_mac_csr_80003es2lan - Release rights to access Kumeran Register + * @hw: pointer to the HW structure + * + * Release the semaphore used to access the Kumeran interface + **/ +static void e1000_release_mac_csr_80003es2lan(struct e1000_hw *hw) +{ + u16 mask; + + DEBUGFUNC("e1000_release_mac_csr_80003es2lan"); + + mask = E1000_SWFW_CSR_SM; + + e1000_release_swfw_sync_80003es2lan(hw, mask); +} + +/** + * e1000_acquire_nvm_80003es2lan - Acquire rights to access NVM + * @hw: pointer to the HW structure + * + * Acquire the semaphore to access the EEPROM. + **/ +static s32 e1000_acquire_nvm_80003es2lan(struct e1000_hw *hw) +{ + s32 ret_val; + + DEBUGFUNC("e1000_acquire_nvm_80003es2lan"); + + ret_val = e1000_acquire_swfw_sync_80003es2lan(hw, E1000_SWFW_EEP_SM); + if (ret_val) + goto out; + + ret_val = e1000_acquire_nvm_generic(hw); + + if (ret_val) + e1000_release_swfw_sync_80003es2lan(hw, E1000_SWFW_EEP_SM); + +out: + return ret_val; +} + +/** + * e1000_release_nvm_80003es2lan - Relinquish rights to access NVM + * @hw: pointer to the HW structure + * + * Release the semaphore used to access the EEPROM. + **/ +static void e1000_release_nvm_80003es2lan(struct e1000_hw *hw) +{ + DEBUGFUNC("e1000_release_nvm_80003es2lan"); + + e1000_release_nvm_generic(hw); + e1000_release_swfw_sync_80003es2lan(hw, E1000_SWFW_EEP_SM); +} + +/** + * e1000_acquire_swfw_sync_80003es2lan - Acquire SW/FW semaphore + * @hw: pointer to the HW structure + * @mask: specifies which semaphore to acquire + * + * Acquire the SW/FW semaphore to access the PHY or NVM. The mask + * will also specify which port we're acquiring the lock for. + **/ +static s32 e1000_acquire_swfw_sync_80003es2lan(struct e1000_hw *hw, u16 mask) +{ + u32 swfw_sync; + u32 swmask = mask; + u32 fwmask = mask << 16; + s32 ret_val = E1000_SUCCESS; + s32 i = 0, timeout = 50; + + DEBUGFUNC("e1000_acquire_swfw_sync_80003es2lan"); + + while (i < timeout) { + if (e1000_get_hw_semaphore_generic(hw)) { + ret_val = -E1000_ERR_SWFW_SYNC; + goto out; + } + + swfw_sync = E1000_READ_REG(hw, E1000_SW_FW_SYNC); + if (!(swfw_sync & (fwmask | swmask))) + break; + + /* + * Firmware currently using resource (fwmask) + * or other software thread using resource (swmask) + */ + e1000_put_hw_semaphore_generic(hw); + msec_delay_irq(5); + i++; + } + + if (i == timeout) { + DEBUGOUT("Driver can't access resource, SW_FW_SYNC timeout.\n"); + ret_val = -E1000_ERR_SWFW_SYNC; + goto out; + } + + swfw_sync |= swmask; + E1000_WRITE_REG(hw, E1000_SW_FW_SYNC, swfw_sync); + + e1000_put_hw_semaphore_generic(hw); + +out: + return ret_val; +} + +/** + * e1000_release_swfw_sync_80003es2lan - Release SW/FW semaphore + * @hw: pointer to the HW structure + * @mask: specifies which semaphore to acquire + * + * Release the SW/FW semaphore used to access the PHY or NVM. The mask + * will also specify which port we're releasing the lock for. + **/ +static void e1000_release_swfw_sync_80003es2lan(struct e1000_hw *hw, u16 mask) +{ + u32 swfw_sync; + + DEBUGFUNC("e1000_release_swfw_sync_80003es2lan"); + + while (e1000_get_hw_semaphore_generic(hw) != E1000_SUCCESS) + ; /* Empty */ + + swfw_sync = E1000_READ_REG(hw, E1000_SW_FW_SYNC); + swfw_sync &= ~mask; + E1000_WRITE_REG(hw, E1000_SW_FW_SYNC, swfw_sync); + + e1000_put_hw_semaphore_generic(hw); +} + +/** + * e1000_read_phy_reg_gg82563_80003es2lan - Read GG82563 PHY register + * @hw: pointer to the HW structure + * @offset: offset of the register to read + * @data: pointer to the data returned from the operation + * + * Read the GG82563 PHY register. + **/ +static s32 e1000_read_phy_reg_gg82563_80003es2lan(struct e1000_hw *hw, + u32 offset, u16 *data) +{ + s32 ret_val; + u32 page_select; + u16 temp; + + DEBUGFUNC("e1000_read_phy_reg_gg82563_80003es2lan"); + + ret_val = e1000_acquire_phy_80003es2lan(hw); + if (ret_val) + goto out; + + /* Select Configuration Page */ + if ((offset & MAX_PHY_REG_ADDRESS) < GG82563_MIN_ALT_REG) { + page_select = GG82563_PHY_PAGE_SELECT; + } else { + /* + * Use Alternative Page Select register to access + * registers 30 and 31 + */ + page_select = GG82563_PHY_PAGE_SELECT_ALT; + } + + temp = (u16)((u16)offset >> GG82563_PAGE_SHIFT); + ret_val = e1000_write_phy_reg_mdic(hw, page_select, temp); + if (ret_val) { + e1000_release_phy_80003es2lan(hw); + goto out; + } + + /* + * The "ready" bit in the MDIC register may be incorrectly set + * before the device has completed the "Page Select" MDI + * transaction. So we wait 200us after each MDI command... + */ + usec_delay(200); + + /* ...and verify the command was successful. */ + ret_val = e1000_read_phy_reg_mdic(hw, page_select, &temp); + + if (((u16)offset >> GG82563_PAGE_SHIFT) != temp) { + ret_val = -E1000_ERR_PHY; + e1000_release_phy_80003es2lan(hw); + goto out; + } + + usec_delay(200); + + ret_val = e1000_read_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & offset, + data); + + usec_delay(200); + e1000_release_phy_80003es2lan(hw); + +out: + return ret_val; +} + +/** + * e1000_write_phy_reg_gg82563_80003es2lan - Write GG82563 PHY register + * @hw: pointer to the HW structure + * @offset: offset of the register to read + * @data: value to write to the register + * + * Write to the GG82563 PHY register. + **/ +static s32 e1000_write_phy_reg_gg82563_80003es2lan(struct e1000_hw *hw, + u32 offset, u16 data) +{ + s32 ret_val; + u32 page_select; + u16 temp; + + DEBUGFUNC("e1000_write_phy_reg_gg82563_80003es2lan"); + + ret_val = e1000_acquire_phy_80003es2lan(hw); + if (ret_val) + goto out; + + /* Select Configuration Page */ + if ((offset & MAX_PHY_REG_ADDRESS) < GG82563_MIN_ALT_REG) { + page_select = GG82563_PHY_PAGE_SELECT; + } else { + /* + * Use Alternative Page Select register to access + * registers 30 and 31 + */ + page_select = GG82563_PHY_PAGE_SELECT_ALT; + } + + temp = (u16)((u16)offset >> GG82563_PAGE_SHIFT); + ret_val = e1000_write_phy_reg_mdic(hw, page_select, temp); + if (ret_val) { + e1000_release_phy_80003es2lan(hw); + goto out; + } + + + /* + * The "ready" bit in the MDIC register may be incorrectly set + * before the device has completed the "Page Select" MDI + * transaction. So we wait 200us after each MDI command... + */ + usec_delay(200); + + /* ...and verify the command was successful. */ + ret_val = e1000_read_phy_reg_mdic(hw, page_select, &temp); + + if (((u16)offset >> GG82563_PAGE_SHIFT) != temp) { + ret_val = -E1000_ERR_PHY; + e1000_release_phy_80003es2lan(hw); + goto out; + } + + usec_delay(200); + + ret_val = e1000_write_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & offset, + data); + + usec_delay(200); + e1000_release_phy_80003es2lan(hw); + +out: + return ret_val; +} + +/** + * e1000_write_nvm_80003es2lan - Write to ESB2 NVM + * @hw: pointer to the HW structure + * @offset: offset of the register to read + * @words: number of words to write + * @data: buffer of data to write to the NVM + * + * Write "words" of data to the ESB2 NVM. + **/ +static s32 e1000_write_nvm_80003es2lan(struct e1000_hw *hw, u16 offset, + u16 words, u16 *data) +{ + DEBUGFUNC("e1000_write_nvm_80003es2lan"); + + return e1000_write_nvm_spi(hw, offset, words, data); +} + +/** + * e1000_get_cfg_done_80003es2lan - Wait for configuration to complete + * @hw: pointer to the HW structure + * + * Wait a specific amount of time for manageability processes to complete. + * This is a function pointer entry point called by the phy module. + **/ +static s32 e1000_get_cfg_done_80003es2lan(struct e1000_hw *hw) +{ + s32 timeout = PHY_CFG_TIMEOUT; + s32 ret_val = E1000_SUCCESS; + u32 mask = E1000_NVM_CFG_DONE_PORT_0; + + DEBUGFUNC("e1000_get_cfg_done_80003es2lan"); + + if (hw->bus.func == 1) + mask = E1000_NVM_CFG_DONE_PORT_1; + + while (timeout) { + if (E1000_READ_REG(hw, E1000_EEMNGCTL) & mask) + break; + msec_delay(1); + timeout--; + } + if (!timeout) { + DEBUGOUT("MNG configuration cycle has not completed.\n"); + ret_val = -E1000_ERR_RESET; + goto out; + } + +out: + return ret_val; +} + +/** + * e1000_phy_force_speed_duplex_80003es2lan - Force PHY speed and duplex + * @hw: pointer to the HW structure + * + * Force the speed and duplex settings onto the PHY. This is a + * function pointer entry point called by the phy module. + **/ +static s32 e1000_phy_force_speed_duplex_80003es2lan(struct e1000_hw *hw) +{ + s32 ret_val = E1000_SUCCESS; + u16 phy_data; + bool link; + + DEBUGFUNC("e1000_phy_force_speed_duplex_80003es2lan"); + + if (!(hw->phy.ops.read_reg)) + goto out; + + /* + * Clear Auto-Crossover to force MDI manually. M88E1000 requires MDI + * forced whenever speed and duplex are forced. + */ + ret_val = hw->phy.ops.read_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data); + if (ret_val) + goto out; + + phy_data &= ~GG82563_PSCR_CROSSOVER_MODE_AUTO; + ret_val = hw->phy.ops.write_reg(hw, GG82563_PHY_SPEC_CTRL, phy_data); + if (ret_val) + goto out; + + DEBUGOUT1("GG82563 PSCR: %X\n", phy_data); + + ret_val = hw->phy.ops.read_reg(hw, PHY_CONTROL, &phy_data); + if (ret_val) + goto out; + + e1000_phy_force_speed_duplex_setup(hw, &phy_data); + + /* Reset the phy to commit changes. */ + phy_data |= MII_CR_RESET; + + ret_val = hw->phy.ops.write_reg(hw, PHY_CONTROL, phy_data); + if (ret_val) + goto out; + + usec_delay(1); + + if (hw->phy.autoneg_wait_to_complete) { + DEBUGOUT("Waiting for forced speed/duplex link " + "on GG82563 phy.\n"); + + ret_val = e1000_phy_has_link_generic(hw, PHY_FORCE_LIMIT, + 100000, &link); + if (ret_val) + goto out; + + if (!link) { + /* + * We didn't get link. + * Reset the DSP and cross our fingers. + */ + ret_val = e1000_phy_reset_dsp_generic(hw); + if (ret_val) + goto out; + } + + /* Try once more */ + ret_val = e1000_phy_has_link_generic(hw, PHY_FORCE_LIMIT, + 100000, &link); + if (ret_val) + goto out; + } + + ret_val = hw->phy.ops.read_reg(hw, GG82563_PHY_MAC_SPEC_CTRL, &phy_data); + if (ret_val) + goto out; + + /* + * Resetting the phy means we need to verify the TX_CLK corresponds + * to the link speed. 10Mbps -> 2.5MHz, else 25MHz. + */ + phy_data &= ~GG82563_MSCR_TX_CLK_MASK; + if (hw->mac.forced_speed_duplex & E1000_ALL_10_SPEED) + phy_data |= GG82563_MSCR_TX_CLK_10MBPS_2_5; + else + phy_data |= GG82563_MSCR_TX_CLK_100MBPS_25; + + /* + * In addition, we must re-enable CRS on Tx for both half and full + * duplex. + */ + phy_data |= GG82563_MSCR_ASSERT_CRS_ON_TX; + ret_val = hw->phy.ops.write_reg(hw, GG82563_PHY_MAC_SPEC_CTRL, phy_data); + +out: + return ret_val; +} + +/** + * e1000_get_cable_length_80003es2lan - Set approximate cable length + * @hw: pointer to the HW structure + * + * Find the approximate cable length as measured by the GG82563 PHY. + * This is a function pointer entry point called by the phy module. + **/ +static s32 e1000_get_cable_length_80003es2lan(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val = E1000_SUCCESS; + u16 phy_data, index; + + DEBUGFUNC("e1000_get_cable_length_80003es2lan"); + + if (!(hw->phy.ops.read_reg)) + goto out; + + ret_val = hw->phy.ops.read_reg(hw, GG82563_PHY_DSP_DISTANCE, &phy_data); + if (ret_val) + goto out; + + index = phy_data & GG82563_DSPD_CABLE_LENGTH; + + if (index < GG82563_CABLE_LENGTH_TABLE_SIZE + 5) { + phy->min_cable_length = e1000_gg82563_cable_length_table[index]; + phy->max_cable_length = + e1000_gg82563_cable_length_table[index+5]; + + phy->cable_length = (phy->min_cable_length + + phy->max_cable_length) / 2; + } else { + ret_val = E1000_ERR_PHY; + } + +out: + return ret_val; +} + +/** + * e1000_get_link_up_info_80003es2lan - Report speed and duplex + * @hw: pointer to the HW structure + * @speed: pointer to speed buffer + * @duplex: pointer to duplex buffer + * + * Retrieve the current speed and duplex configuration. + **/ +static s32 e1000_get_link_up_info_80003es2lan(struct e1000_hw *hw, u16 *speed, + u16 *duplex) +{ + s32 ret_val; + + DEBUGFUNC("e1000_get_link_up_info_80003es2lan"); + + if (hw->phy.media_type == e1000_media_type_copper) { + ret_val = e1000_get_speed_and_duplex_copper_generic(hw, + speed, + duplex); + hw->phy.ops.cfg_on_link_up(hw); + } else { + ret_val = e1000_get_speed_and_duplex_fiber_serdes_generic(hw, + speed, + duplex); + } + + return ret_val; +} + +/** + * e1000_reset_hw_80003es2lan - Reset the ESB2 controller + * @hw: pointer to the HW structure + * + * Perform a global reset to the ESB2 controller. + **/ +static s32 e1000_reset_hw_80003es2lan(struct e1000_hw *hw) +{ + u32 ctrl, icr; + s32 ret_val; + + DEBUGFUNC("e1000_reset_hw_80003es2lan"); + + /* + * Prevent the PCI-E bus from sticking if there is no TLP connection + * on the last TLP read/write transaction when MAC is reset. + */ + ret_val = e1000_disable_pcie_master_generic(hw); + if (ret_val) + DEBUGOUT("PCI-E Master disable polling has failed.\n"); + + DEBUGOUT("Masking off all interrupts\n"); + E1000_WRITE_REG(hw, E1000_IMC, 0xffffffff); + + E1000_WRITE_REG(hw, E1000_RCTL, 0); + E1000_WRITE_REG(hw, E1000_TCTL, E1000_TCTL_PSP); + E1000_WRITE_FLUSH(hw); + + msec_delay(10); + + ctrl = E1000_READ_REG(hw, E1000_CTRL); + + ret_val = e1000_acquire_phy_80003es2lan(hw); + DEBUGOUT("Issuing a global reset to MAC\n"); + E1000_WRITE_REG(hw, E1000_CTRL, ctrl | E1000_CTRL_RST); + e1000_release_phy_80003es2lan(hw); + + ret_val = e1000_get_auto_rd_done_generic(hw); + if (ret_val) + /* We don't want to continue accessing MAC registers. */ + goto out; + + /* Clear any pending interrupt events. */ + E1000_WRITE_REG(hw, E1000_IMC, 0xffffffff); + icr = E1000_READ_REG(hw, E1000_ICR); + + e1000_check_alt_mac_addr_generic(hw); + +out: + return ret_val; +} + +/** + * e1000_init_hw_80003es2lan - Initialize the ESB2 controller + * @hw: pointer to the HW structure + * + * Initialize the hw bits, LED, VFTA, MTA, link and hw counters. + **/ +static s32 e1000_init_hw_80003es2lan(struct e1000_hw *hw) +{ + struct e1000_mac_info *mac = &hw->mac; + u32 reg_data; + s32 ret_val; + u16 i; + + DEBUGFUNC("e1000_init_hw_80003es2lan"); + + e1000_initialize_hw_bits_80003es2lan(hw); + + /* Initialize identification LED */ + ret_val = e1000_id_led_init_generic(hw); + if (ret_val) { + DEBUGOUT("Error initializing identification LED\n"); + /* This is not fatal and we should not stop init due to this */ + } + + /* Disabling VLAN filtering */ + DEBUGOUT("Initializing the IEEE VLAN\n"); + mac->ops.clear_vfta(hw); + + /* Setup the receive address. */ + e1000_init_rx_addrs_generic(hw, mac->rar_entry_count); + + /* Zero out the Multicast HASH table */ + DEBUGOUT("Zeroing the MTA\n"); + for (i = 0; i < mac->mta_reg_count; i++) + E1000_WRITE_REG_ARRAY(hw, E1000_MTA, i, 0); + + /* Setup link and flow control */ + ret_val = mac->ops.setup_link(hw); + + /* Set the transmit descriptor write-back policy */ + reg_data = E1000_READ_REG(hw, E1000_TXDCTL(0)); + reg_data = (reg_data & ~E1000_TXDCTL_WTHRESH) | + E1000_TXDCTL_FULL_TX_DESC_WB | E1000_TXDCTL_COUNT_DESC; + E1000_WRITE_REG(hw, E1000_TXDCTL(0), reg_data); + + /* ...for both queues. */ + reg_data = E1000_READ_REG(hw, E1000_TXDCTL(1)); + reg_data = (reg_data & ~E1000_TXDCTL_WTHRESH) | + E1000_TXDCTL_FULL_TX_DESC_WB | E1000_TXDCTL_COUNT_DESC; + E1000_WRITE_REG(hw, E1000_TXDCTL(1), reg_data); + + /* Enable retransmit on late collisions */ + reg_data = E1000_READ_REG(hw, E1000_TCTL); + reg_data |= E1000_TCTL_RTLC; + E1000_WRITE_REG(hw, E1000_TCTL, reg_data); + + /* Configure Gigabit Carry Extend Padding */ + reg_data = E1000_READ_REG(hw, E1000_TCTL_EXT); + reg_data &= ~E1000_TCTL_EXT_GCEX_MASK; + reg_data |= DEFAULT_TCTL_EXT_GCEX_80003ES2LAN; + E1000_WRITE_REG(hw, E1000_TCTL_EXT, reg_data); + + /* Configure Transmit Inter-Packet Gap */ + reg_data = E1000_READ_REG(hw, E1000_TIPG); + reg_data &= ~E1000_TIPG_IPGT_MASK; + reg_data |= DEFAULT_TIPG_IPGT_1000_80003ES2LAN; + E1000_WRITE_REG(hw, E1000_TIPG, reg_data); + + reg_data = E1000_READ_REG_ARRAY(hw, E1000_FFLT, 0x0001); + reg_data &= ~0x00100000; + E1000_WRITE_REG_ARRAY(hw, E1000_FFLT, 0x0001, reg_data); + + /* + * Clear all of the statistics registers (clear on read). It is + * important that we do this after we have tried to establish link + * because the symbol error count will increment wildly if there + * is no link. + */ + e1000_clear_hw_cntrs_80003es2lan(hw); + + return ret_val; +} + +/** + * e1000_initialize_hw_bits_80003es2lan - Init hw bits of ESB2 + * @hw: pointer to the HW structure + * + * Initializes required hardware-dependent bits needed for normal operation. + **/ +static void e1000_initialize_hw_bits_80003es2lan(struct e1000_hw *hw) +{ + u32 reg; + + DEBUGFUNC("e1000_initialize_hw_bits_80003es2lan"); + + /* Transmit Descriptor Control 0 */ + reg = E1000_READ_REG(hw, E1000_TXDCTL(0)); + reg |= (1 << 22); + E1000_WRITE_REG(hw, E1000_TXDCTL(0), reg); + + /* Transmit Descriptor Control 1 */ + reg = E1000_READ_REG(hw, E1000_TXDCTL(1)); + reg |= (1 << 22); + E1000_WRITE_REG(hw, E1000_TXDCTL(1), reg); + + /* Transmit Arbitration Control 0 */ + reg = E1000_READ_REG(hw, E1000_TARC(0)); + reg &= ~(0xF << 27); /* 30:27 */ + if (hw->phy.media_type != e1000_media_type_copper) + reg &= ~(1 << 20); + E1000_WRITE_REG(hw, E1000_TARC(0), reg); + + /* Transmit Arbitration Control 1 */ + reg = E1000_READ_REG(hw, E1000_TARC(1)); + if (E1000_READ_REG(hw, E1000_TCTL) & E1000_TCTL_MULR) + reg &= ~(1 << 28); + else + reg |= (1 << 28); + E1000_WRITE_REG(hw, E1000_TARC(1), reg); + + return; +} + +/** + * e1000_copper_link_setup_gg82563_80003es2lan - Configure GG82563 Link + * @hw: pointer to the HW structure + * + * Setup some GG82563 PHY registers for obtaining link + **/ +static s32 e1000_copper_link_setup_gg82563_80003es2lan(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val; + u32 ctrl_ext; + u16 data; + + DEBUGFUNC("e1000_copper_link_setup_gg82563_80003es2lan"); + + if (!phy->reset_disable) { + ret_val = hw->phy.ops.read_reg(hw, GG82563_PHY_MAC_SPEC_CTRL, + &data); + if (ret_val) + goto out; + + data |= GG82563_MSCR_ASSERT_CRS_ON_TX; + /* Use 25MHz for both link down and 1000Base-T for Tx clock. */ + data |= GG82563_MSCR_TX_CLK_1000MBPS_25; + + ret_val = hw->phy.ops.write_reg(hw, GG82563_PHY_MAC_SPEC_CTRL, + data); + if (ret_val) + goto out; + + /* + * Options: + * MDI/MDI-X = 0 (default) + * 0 - Auto for all speeds + * 1 - MDI mode + * 2 - MDI-X mode + * 3 - Auto for 1000Base-T only (MDI-X for 10/100Base-T modes) + */ + ret_val = hw->phy.ops.read_reg(hw, GG82563_PHY_SPEC_CTRL, &data); + if (ret_val) + goto out; + + data &= ~GG82563_PSCR_CROSSOVER_MODE_MASK; + + switch (phy->mdix) { + case 1: + data |= GG82563_PSCR_CROSSOVER_MODE_MDI; + break; + case 2: + data |= GG82563_PSCR_CROSSOVER_MODE_MDIX; + break; + case 0: + default: + data |= GG82563_PSCR_CROSSOVER_MODE_AUTO; + break; + } + + /* + * Options: + * disable_polarity_correction = 0 (default) + * Automatic Correction for Reversed Cable Polarity + * 0 - Disabled + * 1 - Enabled + */ + data &= ~GG82563_PSCR_POLARITY_REVERSAL_DISABLE; + if (phy->disable_polarity_correction) + data |= GG82563_PSCR_POLARITY_REVERSAL_DISABLE; + + ret_val = hw->phy.ops.write_reg(hw, GG82563_PHY_SPEC_CTRL, data); + if (ret_val) + goto out; + + /* SW Reset the PHY so all changes take effect */ + ret_val = hw->phy.ops.commit(hw); + if (ret_val) { + DEBUGOUT("Error Resetting the PHY\n"); + goto out; + } + + } + + /* Bypass Rx and Tx FIFO's */ + ret_val = e1000_write_kmrn_reg_80003es2lan(hw, + E1000_KMRNCTRLSTA_OFFSET_FIFO_CTRL, + E1000_KMRNCTRLSTA_FIFO_CTRL_RX_BYPASS | + E1000_KMRNCTRLSTA_FIFO_CTRL_TX_BYPASS); + if (ret_val) + goto out; + + ret_val = e1000_read_kmrn_reg_80003es2lan(hw, + E1000_KMRNCTRLSTA_OFFSET_MAC2PHY_OPMODE, + &data); + if (ret_val) + goto out; + data |= E1000_KMRNCTRLSTA_OPMODE_E_IDLE; + ret_val = e1000_write_kmrn_reg_80003es2lan(hw, + E1000_KMRNCTRLSTA_OFFSET_MAC2PHY_OPMODE, + data); + if (ret_val) + goto out; + + ret_val = hw->phy.ops.read_reg(hw, GG82563_PHY_SPEC_CTRL_2, &data); + if (ret_val) + goto out; + + data &= ~GG82563_PSCR2_REVERSE_AUTO_NEG; + ret_val = hw->phy.ops.write_reg(hw, GG82563_PHY_SPEC_CTRL_2, data); + if (ret_val) + goto out; + + ctrl_ext = E1000_READ_REG(hw, E1000_CTRL_EXT); + ctrl_ext &= ~(E1000_CTRL_EXT_LINK_MODE_MASK); + E1000_WRITE_REG(hw, E1000_CTRL_EXT, ctrl_ext); + + ret_val = hw->phy.ops.read_reg(hw, GG82563_PHY_PWR_MGMT_CTRL, &data); + if (ret_val) + goto out; + + /* + * Do not init these registers when the HW is in IAMT mode, since the + * firmware will have already initialized them. We only initialize + * them if the HW is not in IAMT mode. + */ + if (!(hw->mac.ops.check_mng_mode(hw))) { + /* Enable Electrical Idle on the PHY */ + data |= GG82563_PMCR_ENABLE_ELECTRICAL_IDLE; + ret_val = hw->phy.ops.write_reg(hw, + GG82563_PHY_PWR_MGMT_CTRL, + data); + if (ret_val) + goto out; + ret_val = hw->phy.ops.read_reg(hw, + GG82563_PHY_KMRN_MODE_CTRL, + &data); + if (ret_val) + goto out; + + data &= ~GG82563_KMCR_PASS_FALSE_CARRIER; + ret_val = hw->phy.ops.write_reg(hw, + GG82563_PHY_KMRN_MODE_CTRL, + data); + + if (ret_val) + goto out; + } + + /* + * Workaround: Disable padding in Kumeran interface in the MAC + * and in the PHY to avoid CRC errors. + */ + ret_val = hw->phy.ops.read_reg(hw, GG82563_PHY_INBAND_CTRL, &data); + if (ret_val) + goto out; + + data |= GG82563_ICR_DIS_PADDING; + ret_val = hw->phy.ops.write_reg(hw, GG82563_PHY_INBAND_CTRL, data); + if (ret_val) + goto out; + +out: + return ret_val; +} + +/** + * e1000_setup_copper_link_80003es2lan - Setup Copper Link for ESB2 + * @hw: pointer to the HW structure + * + * Essentially a wrapper for setting up all things "copper" related. + * This is a function pointer entry point called by the mac module. + **/ +static s32 e1000_setup_copper_link_80003es2lan(struct e1000_hw *hw) +{ + u32 ctrl; + s32 ret_val; + u16 reg_data; + + DEBUGFUNC("e1000_setup_copper_link_80003es2lan"); + + ctrl = E1000_READ_REG(hw, E1000_CTRL); + ctrl |= E1000_CTRL_SLU; + ctrl &= ~(E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX); + E1000_WRITE_REG(hw, E1000_CTRL, ctrl); + + /* + * Set the mac to wait the maximum time between each + * iteration and increase the max iterations when + * polling the phy; this fixes erroneous timeouts at 10Mbps. + */ + ret_val = e1000_write_kmrn_reg_80003es2lan(hw, GG82563_REG(0x34, 4), + 0xFFFF); + if (ret_val) + goto out; + ret_val = e1000_read_kmrn_reg_80003es2lan(hw, GG82563_REG(0x34, 9), + ®_data); + if (ret_val) + goto out; + reg_data |= 0x3F; + ret_val = e1000_write_kmrn_reg_80003es2lan(hw, GG82563_REG(0x34, 9), + reg_data); + if (ret_val) + goto out; + ret_val = e1000_read_kmrn_reg_80003es2lan(hw, + E1000_KMRNCTRLSTA_OFFSET_INB_CTRL, + ®_data); + if (ret_val) + goto out; + reg_data |= E1000_KMRNCTRLSTA_INB_CTRL_DIS_PADDING; + ret_val = e1000_write_kmrn_reg_80003es2lan(hw, + E1000_KMRNCTRLSTA_OFFSET_INB_CTRL, + reg_data); + if (ret_val) + goto out; + + ret_val = e1000_copper_link_setup_gg82563_80003es2lan(hw); + if (ret_val) + goto out; + + ret_val = e1000_setup_copper_link_generic(hw); + +out: + return ret_val; +} + +/** + * e1000_cfg_on_link_up_80003es2lan - es2 link configuration after link-up + * @hw: pointer to the HW structure + * @duplex: current duplex setting + * + * Configure the KMRN interface by applying last minute quirks for + * 10/100 operation. + **/ +static s32 e1000_cfg_on_link_up_80003es2lan(struct e1000_hw *hw) +{ + s32 ret_val = E1000_SUCCESS; + u16 speed; + u16 duplex; + + DEBUGFUNC("e1000_configure_on_link_up"); + + if (hw->phy.media_type == e1000_media_type_copper) { + + ret_val = e1000_get_speed_and_duplex_copper_generic(hw, + &speed, + &duplex); + if (ret_val) + goto out; + + if (speed == SPEED_1000) + ret_val = e1000_cfg_kmrn_1000_80003es2lan(hw); + else + ret_val = e1000_cfg_kmrn_10_100_80003es2lan(hw, duplex); + } + +out: + return ret_val; +} + +/** + * e1000_cfg_kmrn_10_100_80003es2lan - Apply "quirks" for 10/100 operation + * @hw: pointer to the HW structure + * @duplex: current duplex setting + * + * Configure the KMRN interface by applying last minute quirks for + * 10/100 operation. + **/ +static s32 e1000_cfg_kmrn_10_100_80003es2lan(struct e1000_hw *hw, u16 duplex) +{ + s32 ret_val = E1000_SUCCESS; + u32 tipg; + u32 i = 0; + u16 reg_data, reg_data2; + + DEBUGFUNC("e1000_configure_kmrn_for_10_100"); + + reg_data = E1000_KMRNCTRLSTA_HD_CTRL_10_100_DEFAULT; + ret_val = e1000_write_kmrn_reg_80003es2lan(hw, + E1000_KMRNCTRLSTA_OFFSET_HD_CTRL, + reg_data); + if (ret_val) + goto out; + + /* Configure Transmit Inter-Packet Gap */ + tipg = E1000_READ_REG(hw, E1000_TIPG); + tipg &= ~E1000_TIPG_IPGT_MASK; + tipg |= DEFAULT_TIPG_IPGT_10_100_80003ES2LAN; + E1000_WRITE_REG(hw, E1000_TIPG, tipg); + + + do { + ret_val = hw->phy.ops.read_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, + ®_data); + if (ret_val) + goto out; + + ret_val = hw->phy.ops.read_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, + ®_data2); + if (ret_val) + goto out; + i++; + } while ((reg_data != reg_data2) && (i < GG82563_MAX_KMRN_RETRY)); + + if (duplex == HALF_DUPLEX) + reg_data |= GG82563_KMCR_PASS_FALSE_CARRIER; + else + reg_data &= ~GG82563_KMCR_PASS_FALSE_CARRIER; + + ret_val = hw->phy.ops.write_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, reg_data); + +out: + return ret_val; +} + +/** + * e1000_cfg_kmrn_1000_80003es2lan - Apply "quirks" for gigabit operation + * @hw: pointer to the HW structure + * + * Configure the KMRN interface by applying last minute quirks for + * gigabit operation. + **/ +static s32 e1000_cfg_kmrn_1000_80003es2lan(struct e1000_hw *hw) +{ + s32 ret_val = E1000_SUCCESS; + u16 reg_data, reg_data2; + u32 tipg; + u32 i = 0; + + DEBUGFUNC("e1000_configure_kmrn_for_1000"); + + reg_data = E1000_KMRNCTRLSTA_HD_CTRL_1000_DEFAULT; + ret_val = e1000_write_kmrn_reg_80003es2lan(hw, + E1000_KMRNCTRLSTA_OFFSET_HD_CTRL, + reg_data); + if (ret_val) + goto out; + + /* Configure Transmit Inter-Packet Gap */ + tipg = E1000_READ_REG(hw, E1000_TIPG); + tipg &= ~E1000_TIPG_IPGT_MASK; + tipg |= DEFAULT_TIPG_IPGT_1000_80003ES2LAN; + E1000_WRITE_REG(hw, E1000_TIPG, tipg); + + + do { + ret_val = hw->phy.ops.read_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, + ®_data); + if (ret_val) + goto out; + + ret_val = hw->phy.ops.read_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, + ®_data2); + if (ret_val) + goto out; + i++; + } while ((reg_data != reg_data2) && (i < GG82563_MAX_KMRN_RETRY)); + + reg_data &= ~GG82563_KMCR_PASS_FALSE_CARRIER; + ret_val = hw->phy.ops.write_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, reg_data); + +out: + return ret_val; +} + +/** + * e1000_read_kmrn_reg_80003es2lan - Read kumeran register + * @hw: pointer to the HW structure + * @offset: register offset to be read + * @data: pointer to the read data + * + * Acquire semaphore, then read the PHY register at offset + * using the kumeran interface. The information retrieved is stored in data. + * Release the semaphore before exiting. + **/ +s32 e1000_read_kmrn_reg_80003es2lan(struct e1000_hw *hw, u32 offset, u16 *data) +{ + u32 kmrnctrlsta; + s32 ret_val = E1000_SUCCESS; + + DEBUGFUNC("e1000_read_kmrn_reg_80003es2lan"); + + ret_val = e1000_acquire_mac_csr_80003es2lan(hw); + if (ret_val) + goto out; + + kmrnctrlsta = ((offset << E1000_KMRNCTRLSTA_OFFSET_SHIFT) & + E1000_KMRNCTRLSTA_OFFSET) | E1000_KMRNCTRLSTA_REN; + E1000_WRITE_REG(hw, E1000_KMRNCTRLSTA, kmrnctrlsta); + + usec_delay(2); + + kmrnctrlsta = E1000_READ_REG(hw, E1000_KMRNCTRLSTA); + *data = (u16)kmrnctrlsta; + + e1000_release_mac_csr_80003es2lan(hw); + +out: + return ret_val; +} + +/** + * e1000_write_kmrn_reg_80003es2lan - Write kumeran register + * @hw: pointer to the HW structure + * @offset: register offset to write to + * @data: data to write at register offset + * + * Acquire semaphore, then write the data to PHY register + * at the offset using the kumeran interface. Release semaphore + * before exiting. + **/ +s32 e1000_write_kmrn_reg_80003es2lan(struct e1000_hw *hw, u32 offset, u16 data) +{ + u32 kmrnctrlsta; + s32 ret_val = E1000_SUCCESS; + + DEBUGFUNC("e1000_write_kmrn_reg_80003es2lan"); + + ret_val = e1000_acquire_mac_csr_80003es2lan(hw); + if (ret_val) + goto out; + + kmrnctrlsta = ((offset << E1000_KMRNCTRLSTA_OFFSET_SHIFT) & + E1000_KMRNCTRLSTA_OFFSET) | data; + E1000_WRITE_REG(hw, E1000_KMRNCTRLSTA, kmrnctrlsta); + + usec_delay(2); + + e1000_release_mac_csr_80003es2lan(hw); + +out: + return ret_val; +} + +/** + * e1000_read_mac_addr_80003es2lan - Read device MAC address + * @hw: pointer to the HW structure + **/ +static s32 e1000_read_mac_addr_80003es2lan(struct e1000_hw *hw) +{ + s32 ret_val = E1000_SUCCESS; + + DEBUGFUNC("e1000_read_mac_addr_80003es2lan"); + if (e1000_check_alt_mac_addr_generic(hw)) + ret_val = e1000_read_mac_addr_generic(hw); + + return ret_val; +} + +/** + * e1000_power_down_phy_copper_80003es2lan - Remove link during PHY power down + * @hw: pointer to the HW structure + * + * In the case of a PHY power down to save power, or to turn off link during a + * driver unload, or wake on lan is not enabled, remove the link. + **/ +static void e1000_power_down_phy_copper_80003es2lan(struct e1000_hw *hw) +{ + /* If the management interface is not enabled, then power down */ + if (!(hw->mac.ops.check_mng_mode(hw) || + hw->phy.ops.check_reset_block(hw))) + e1000_power_down_phy_copper(hw); + + return; +} + +/** + * e1000_clear_hw_cntrs_80003es2lan - Clear device specific hardware counters + * @hw: pointer to the HW structure + * + * Clears the hardware counters by reading the counter registers. + **/ +static void e1000_clear_hw_cntrs_80003es2lan(struct e1000_hw *hw) +{ + DEBUGFUNC("e1000_clear_hw_cntrs_80003es2lan"); + + e1000_clear_hw_cntrs_base_generic(hw); + + E1000_READ_REG(hw, E1000_PRC64); + E1000_READ_REG(hw, E1000_PRC127); + E1000_READ_REG(hw, E1000_PRC255); + E1000_READ_REG(hw, E1000_PRC511); + E1000_READ_REG(hw, E1000_PRC1023); + E1000_READ_REG(hw, E1000_PRC1522); + E1000_READ_REG(hw, E1000_PTC64); + E1000_READ_REG(hw, E1000_PTC127); + E1000_READ_REG(hw, E1000_PTC255); + E1000_READ_REG(hw, E1000_PTC511); + E1000_READ_REG(hw, E1000_PTC1023); + E1000_READ_REG(hw, E1000_PTC1522); + + E1000_READ_REG(hw, E1000_ALGNERRC); + E1000_READ_REG(hw, E1000_RXERRC); + E1000_READ_REG(hw, E1000_TNCRS); + E1000_READ_REG(hw, E1000_CEXTERR); + E1000_READ_REG(hw, E1000_TSCTC); + E1000_READ_REG(hw, E1000_TSCTFC); + + E1000_READ_REG(hw, E1000_MGTPRC); + E1000_READ_REG(hw, E1000_MGTPDC); + E1000_READ_REG(hw, E1000_MGTPTC); + + E1000_READ_REG(hw, E1000_IAC); + E1000_READ_REG(hw, E1000_ICRXOC); + + E1000_READ_REG(hw, E1000_ICRXPTC); + E1000_READ_REG(hw, E1000_ICRXATC); + E1000_READ_REG(hw, E1000_ICTXPTC); + E1000_READ_REG(hw, E1000_ICTXATC); + E1000_READ_REG(hw, E1000_ICTXQEC); + E1000_READ_REG(hw, E1000_ICTXQMTC); + E1000_READ_REG(hw, E1000_ICRXDMTC); +} diff --git a/sys/dev/netif/ig_hal/e1000_80003es2lan.h b/sys/dev/netif/ig_hal/e1000_80003es2lan.h new file mode 100644 index 0000000000..7bf8d9d543 --- /dev/null +++ b/sys/dev/netif/ig_hal/e1000_80003es2lan.h @@ -0,0 +1,102 @@ +/******************************************************************************* + + Copyright (c) 2001-2008, Intel Corporation + All rights reserved. + + Redistribution and use in source and binary forms, with or without + modification, are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, + this list of conditions and the following disclaimer. + + 2. Redistributions in binary form must reproduce the above copyright + notice, this list of conditions and the following disclaimer in the + documentation and/or other materials provided with the distribution. + + 3. Neither the name of the Intel Corporation nor the names of its + contributors may be used to endorse or promote products derived from + this software without specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE + ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE + LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR + CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF + SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS + INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN + CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) + ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + POSSIBILITY OF SUCH DAMAGE. + +*******************************************************************************/ +/* $FreeBSD$ */ + + +#ifndef _E1000_80003ES2LAN_H_ +#define _E1000_80003ES2LAN_H_ + +#define E1000_KMRNCTRLSTA_OFFSET_FIFO_CTRL 0x00 +#define E1000_KMRNCTRLSTA_OFFSET_INB_CTRL 0x02 +#define E1000_KMRNCTRLSTA_OFFSET_HD_CTRL 0x10 +#define E1000_KMRNCTRLSTA_OFFSET_MAC2PHY_OPMODE 0x1F + +#define E1000_KMRNCTRLSTA_FIFO_CTRL_RX_BYPASS 0x0008 +#define E1000_KMRNCTRLSTA_FIFO_CTRL_TX_BYPASS 0x0800 +#define E1000_KMRNCTRLSTA_INB_CTRL_DIS_PADDING 0x0010 + +#define E1000_KMRNCTRLSTA_HD_CTRL_10_100_DEFAULT 0x0004 +#define E1000_KMRNCTRLSTA_HD_CTRL_1000_DEFAULT 0x0000 +#define E1000_KMRNCTRLSTA_OPMODE_E_IDLE 0x2000 + +#define E1000_TCTL_EXT_GCEX_MASK 0x000FFC00 /* Gigabit Carry Extend Padding */ +#define DEFAULT_TCTL_EXT_GCEX_80003ES2LAN 0x00010000 + +#define DEFAULT_TIPG_IPGT_1000_80003ES2LAN 0x8 +#define DEFAULT_TIPG_IPGT_10_100_80003ES2LAN 0x9 + +/* GG82563 PHY Specific Status Register (Page 0, Register 16 */ +#define GG82563_PSCR_POLARITY_REVERSAL_DISABLE 0x0002 /* 1=Reversal Disabled */ +#define GG82563_PSCR_CROSSOVER_MODE_MASK 0x0060 +#define GG82563_PSCR_CROSSOVER_MODE_MDI 0x0000 /* 00=Manual MDI */ +#define GG82563_PSCR_CROSSOVER_MODE_MDIX 0x0020 /* 01=Manual MDIX */ +#define GG82563_PSCR_CROSSOVER_MODE_AUTO 0x0060 /* 11=Auto crossover */ + +/* PHY Specific Control Register 2 (Page 0, Register 26) */ +#define GG82563_PSCR2_REVERSE_AUTO_NEG 0x2000 + /* 1=Reverse Auto-Negotiation */ + +/* MAC Specific Control Register (Page 2, Register 21) */ +/* Tx clock speed for Link Down and 1000BASE-T for the following speeds */ +#define GG82563_MSCR_TX_CLK_MASK 0x0007 +#define GG82563_MSCR_TX_CLK_10MBPS_2_5 0x0004 +#define GG82563_MSCR_TX_CLK_100MBPS_25 0x0005 +#define GG82563_MSCR_TX_CLK_1000MBPS_2_5 0x0006 +#define GG82563_MSCR_TX_CLK_1000MBPS_25 0x0007 + +#define GG82563_MSCR_ASSERT_CRS_ON_TX 0x0010 /* 1=Assert */ + +/* DSP Distance Register (Page 5, Register 26) */ +/* + * 0 = <50M + * 1 = 50-80M + * 2 = 80-100M + * 3 = 110-140M + * 4 = >140M + */ +#define GG82563_DSPD_CABLE_LENGTH 0x0007 + +/* Kumeran Mode Control Register (Page 193, Register 16) */ +#define GG82563_KMCR_PASS_FALSE_CARRIER 0x0800 + +/* Max number of times Kumeran read/write should be validated */ +#define GG82563_MAX_KMRN_RETRY 0x5 + +/* Power Management Control Register (Page 193, Register 20) */ +#define GG82563_PMCR_ENABLE_ELECTRICAL_IDLE 0x0001 + /* 1=Enable SERDES Electrical Idle */ + +/* In-Band Control Register (Page 194, Register 18) */ +#define GG82563_ICR_DIS_PADDING 0x0010 /* Disable Padding */ + +#endif diff --git a/sys/dev/netif/ig_hal/e1000_82540.c b/sys/dev/netif/ig_hal/e1000_82540.c new file mode 100644 index 0000000000..6967261cd0 --- /dev/null +++ b/sys/dev/netif/ig_hal/e1000_82540.c @@ -0,0 +1,676 @@ +/****************************************************************************** + + Copyright (c) 2001-2008, Intel Corporation + All rights reserved. + + Redistribution and use in source and binary forms, with or without + modification, are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, + this list of conditions and the following disclaimer. + + 2. Redistributions in binary form must reproduce the above copyright + notice, this list of conditions and the following disclaimer in the + documentation and/or other materials provided with the distribution. + + 3. Neither the name of the Intel Corporation nor the names of its + contributors may be used to endorse or promote products derived from + this software without specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE + ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE + LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR + CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF + SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS + INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN + CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) + ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + POSSIBILITY OF SUCH DAMAGE. + +******************************************************************************/ +/*$FreeBSD$*/ + +/* + * 82540EM Gigabit Ethernet Controller + * 82540EP Gigabit Ethernet Controller + * 82545EM Gigabit Ethernet Controller (Copper) + * 82545EM Gigabit Ethernet Controller (Fiber) + * 82545GM Gigabit Ethernet Controller + * 82546EB Gigabit Ethernet Controller (Copper) + * 82546EB Gigabit Ethernet Controller (Fiber) + * 82546GB Gigabit Ethernet Controller + */ + +#include "e1000_api.h" + +static s32 e1000_init_phy_params_82540(struct e1000_hw *hw); +static s32 e1000_init_nvm_params_82540(struct e1000_hw *hw); +static s32 e1000_init_mac_params_82540(struct e1000_hw *hw); +static s32 e1000_adjust_serdes_amplitude_82540(struct e1000_hw *hw); +static void e1000_clear_hw_cntrs_82540(struct e1000_hw *hw); +static s32 e1000_init_hw_82540(struct e1000_hw *hw); +static s32 e1000_reset_hw_82540(struct e1000_hw *hw); +static s32 e1000_set_phy_mode_82540(struct e1000_hw *hw); +static s32 e1000_set_vco_speed_82540(struct e1000_hw *hw); +static s32 e1000_setup_copper_link_82540(struct e1000_hw *hw); +static s32 e1000_setup_fiber_serdes_link_82540(struct e1000_hw *hw); +static void e1000_power_down_phy_copper_82540(struct e1000_hw *hw); + +/** + * e1000_init_phy_params_82540 - Init PHY func ptrs. + * @hw: pointer to the HW structure + **/ +static s32 e1000_init_phy_params_82540(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val = E1000_SUCCESS; + + phy->addr = 1; + phy->autoneg_mask = AUTONEG_ADVERTISE_SPEED_DEFAULT; + phy->reset_delay_us = 10000; + phy->type = e1000_phy_m88; + + /* Function Pointers */ + phy->ops.check_polarity = e1000_check_polarity_m88; + phy->ops.commit = e1000_phy_sw_reset_generic; + phy->ops.force_speed_duplex = e1000_phy_force_speed_duplex_m88; + phy->ops.get_cable_length = e1000_get_cable_length_m88; + phy->ops.get_cfg_done = e1000_get_cfg_done_generic; + phy->ops.read_reg = e1000_read_phy_reg_m88; + phy->ops.reset = e1000_phy_hw_reset_generic; + phy->ops.write_reg = e1000_write_phy_reg_m88; + phy->ops.get_info = e1000_get_phy_info_m88; + phy->ops.power_up = e1000_power_up_phy_copper; + phy->ops.power_down = e1000_power_down_phy_copper_82540; + + ret_val = e1000_get_phy_id(hw); + if (ret_val) + goto out; + + /* Verify phy id */ + switch (hw->mac.type) { + case e1000_82540: + case e1000_82545: + case e1000_82545_rev_3: + case e1000_82546: + case e1000_82546_rev_3: + if (phy->id == M88E1011_I_PHY_ID) + break; + /* Fall Through */ + default: + ret_val = -E1000_ERR_PHY; + goto out; + break; + } + +out: + return ret_val; +} + +/** + * e1000_init_nvm_params_82540 - Init NVM func ptrs. + * @hw: pointer to the HW structure + **/ +static s32 e1000_init_nvm_params_82540(struct e1000_hw *hw) +{ + struct e1000_nvm_info *nvm = &hw->nvm; + u32 eecd = E1000_READ_REG(hw, E1000_EECD); + + DEBUGFUNC("e1000_init_nvm_params_82540"); + + nvm->type = e1000_nvm_eeprom_microwire; + nvm->delay_usec = 50; + nvm->opcode_bits = 3; + switch (nvm->override) { + case e1000_nvm_override_microwire_large: + nvm->address_bits = 8; + nvm->word_size = 256; + break; + case e1000_nvm_override_microwire_small: + nvm->address_bits = 6; + nvm->word_size = 64; + break; + default: + nvm->address_bits = eecd & E1000_EECD_SIZE ? 8 : 6; + nvm->word_size = eecd & E1000_EECD_SIZE ? 256 : 64; + break; + } + + /* Function Pointers */ + nvm->ops.acquire = e1000_acquire_nvm_generic; + nvm->ops.read = e1000_read_nvm_microwire; + nvm->ops.release = e1000_release_nvm_generic; + nvm->ops.update = e1000_update_nvm_checksum_generic; + nvm->ops.valid_led_default = e1000_valid_led_default_generic; + nvm->ops.validate = e1000_validate_nvm_checksum_generic; + nvm->ops.write = e1000_write_nvm_microwire; + + return E1000_SUCCESS; +} + +/** + * e1000_init_mac_params_82540 - Init MAC func ptrs. + * @hw: pointer to the HW structure + **/ +static s32 e1000_init_mac_params_82540(struct e1000_hw *hw) +{ + struct e1000_mac_info *mac = &hw->mac; + s32 ret_val = E1000_SUCCESS; + + DEBUGFUNC("e1000_init_mac_params_82540"); + + /* Set media type */ + switch (hw->device_id) { + case E1000_DEV_ID_82545EM_FIBER: + case E1000_DEV_ID_82545GM_FIBER: + case E1000_DEV_ID_82546EB_FIBER: + case E1000_DEV_ID_82546GB_FIBER: + hw->phy.media_type = e1000_media_type_fiber; + break; + case E1000_DEV_ID_82545GM_SERDES: + case E1000_DEV_ID_82546GB_SERDES: + hw->phy.media_type = e1000_media_type_internal_serdes; + break; + default: + hw->phy.media_type = e1000_media_type_copper; + break; + } + + /* Set mta register count */ + mac->mta_reg_count = 128; + /* Set rar entry count */ + mac->rar_entry_count = E1000_RAR_ENTRIES; + + /* Function pointers */ + + /* bus type/speed/width */ + mac->ops.get_bus_info = e1000_get_bus_info_pci_generic; + /* function id */ + mac->ops.set_lan_id = e1000_set_lan_id_multi_port_pci; + /* reset */ + mac->ops.reset_hw = e1000_reset_hw_82540; + /* hw initialization */ + mac->ops.init_hw = e1000_init_hw_82540; + /* link setup */ + mac->ops.setup_link = e1000_setup_link_generic; + /* physical interface setup */ + mac->ops.setup_physical_interface = + (hw->phy.media_type == e1000_media_type_copper) + ? e1000_setup_copper_link_82540 + : e1000_setup_fiber_serdes_link_82540; + /* check for link */ + switch (hw->phy.media_type) { + case e1000_media_type_copper: + mac->ops.check_for_link = e1000_check_for_copper_link_generic; + break; + case e1000_media_type_fiber: + mac->ops.check_for_link = e1000_check_for_fiber_link_generic; + break; + case e1000_media_type_internal_serdes: + mac->ops.check_for_link = e1000_check_for_serdes_link_generic; + break; + default: + ret_val = -E1000_ERR_CONFIG; + goto out; + break; + } + /* link info */ + mac->ops.get_link_up_info = + (hw->phy.media_type == e1000_media_type_copper) + ? e1000_get_speed_and_duplex_copper_generic + : e1000_get_speed_and_duplex_fiber_serdes_generic; + /* multicast address update */ + mac->ops.update_mc_addr_list = e1000_update_mc_addr_list_generic; + /* writing VFTA */ + mac->ops.write_vfta = e1000_write_vfta_generic; + /* clearing VFTA */ + mac->ops.clear_vfta = e1000_clear_vfta_generic; + /* setting MTA */ + mac->ops.mta_set = e1000_mta_set_generic; + /* setup LED */ + mac->ops.setup_led = e1000_setup_led_generic; + /* cleanup LED */ + mac->ops.cleanup_led = e1000_cleanup_led_generic; + /* turn on/off LED */ + mac->ops.led_on = e1000_led_on_generic; + mac->ops.led_off = e1000_led_off_generic; + /* clear hardware counters */ + mac->ops.clear_hw_cntrs = e1000_clear_hw_cntrs_82540; + +out: + return ret_val; +} + +/** + * e1000_init_function_pointers_82540 - Init func ptrs. + * @hw: pointer to the HW structure + * + * Called to initialize all function pointers and parameters. + **/ +void e1000_init_function_pointers_82540(struct e1000_hw *hw) +{ + DEBUGFUNC("e1000_init_function_pointers_82540"); + + hw->mac.ops.init_params = e1000_init_mac_params_82540; + hw->nvm.ops.init_params = e1000_init_nvm_params_82540; + hw->phy.ops.init_params = e1000_init_phy_params_82540; +} + +/** + * e1000_reset_hw_82540 - Reset hardware + * @hw: pointer to the HW structure + * + * This resets the hardware into a known state. + **/ +static s32 e1000_reset_hw_82540(struct e1000_hw *hw) +{ + u32 ctrl, icr, manc; + s32 ret_val = E1000_SUCCESS; + + DEBUGFUNC("e1000_reset_hw_82540"); + + DEBUGOUT("Masking off all interrupts\n"); + E1000_WRITE_REG(hw, E1000_IMC, 0xFFFFFFFF); + + E1000_WRITE_REG(hw, E1000_RCTL, 0); + E1000_WRITE_REG(hw, E1000_TCTL, E1000_TCTL_PSP); + E1000_WRITE_FLUSH(hw); + + /* + * Delay to allow any outstanding PCI transactions to complete + * before resetting the device. + */ + msec_delay(10); + + ctrl = E1000_READ_REG(hw, E1000_CTRL); + + DEBUGOUT("Issuing a global reset to 82540/82545/82546 MAC\n"); + switch (hw->mac.type) { + case e1000_82545_rev_3: + case e1000_82546_rev_3: + E1000_WRITE_REG(hw, E1000_CTRL_DUP, ctrl | E1000_CTRL_RST); + break; + default: + /* + * These controllers can't ack the 64-bit write when + * issuing the reset, so we use IO-mapping as a + * workaround to issue the reset. + */ + E1000_WRITE_REG_IO(hw, E1000_CTRL, ctrl | E1000_CTRL_RST); + break; + } + + /* Wait for EEPROM reload */ + msec_delay(5); + + /* Disable HW ARPs on ASF enabled adapters */ + manc = E1000_READ_REG(hw, E1000_MANC); + manc &= ~E1000_MANC_ARP_EN; + E1000_WRITE_REG(hw, E1000_MANC, manc); + + E1000_WRITE_REG(hw, E1000_IMC, 0xffffffff); + icr = E1000_READ_REG(hw, E1000_ICR); + + return ret_val; +} + +/** + * e1000_init_hw_82540 - Initialize hardware + * @hw: pointer to the HW structure + * + * This inits the hardware readying it for operation. + **/ +static s32 e1000_init_hw_82540(struct e1000_hw *hw) +{ + struct e1000_mac_info *mac = &hw->mac; + u32 txdctl, ctrl_ext; + s32 ret_val = E1000_SUCCESS; + u16 i; + + DEBUGFUNC("e1000_init_hw_82540"); + + /* Initialize identification LED */ + ret_val = e1000_id_led_init_generic(hw); + if (ret_val) { + DEBUGOUT("Error initializing identification LED\n"); + /* This is not fatal and we should not stop init due to this */ + } + + /* Disabling VLAN filtering */ + DEBUGOUT("Initializing the IEEE VLAN\n"); + if (mac->type < e1000_82545_rev_3) + E1000_WRITE_REG(hw, E1000_VET, 0); + + mac->ops.clear_vfta(hw); + + /* Setup the receive address. */ + e1000_init_rx_addrs_generic(hw, mac->rar_entry_count); + + /* Zero out the Multicast HASH table */ + DEBUGOUT("Zeroing the MTA\n"); + for (i = 0; i < mac->mta_reg_count; i++) { + E1000_WRITE_REG_ARRAY(hw, E1000_MTA, i, 0); + /* + * Avoid back to back register writes by adding the register + * read (flush). This is to protect against some strange + * bridge configurations that may issue Memory Write Block + * (MWB) to our register space. The *_rev_3 hardware at + * least doesn't respond correctly to every other dword in an + * MWB to our register space. + */ + E1000_WRITE_FLUSH(hw); + } + + if (mac->type < e1000_82545_rev_3) + e1000_pcix_mmrbc_workaround_generic(hw); + + /* Setup link and flow control */ + ret_val = mac->ops.setup_link(hw); + + txdctl = E1000_READ_REG(hw, E1000_TXDCTL(0)); + txdctl = (txdctl & ~E1000_TXDCTL_WTHRESH) | + E1000_TXDCTL_FULL_TX_DESC_WB; + E1000_WRITE_REG(hw, E1000_TXDCTL(0), txdctl); + + /* + * Clear all of the statistics registers (clear on read). It is + * important that we do this after we have tried to establish link + * because the symbol error count will increment wildly if there + * is no link. + */ + e1000_clear_hw_cntrs_82540(hw); + + if ((hw->device_id == E1000_DEV_ID_82546GB_QUAD_COPPER) || + (hw->device_id == E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3)) { + ctrl_ext = E1000_READ_REG(hw, E1000_CTRL_EXT); + /* + * Relaxed ordering must be disabled to avoid a parity + * error crash in a PCI slot. + */ + ctrl_ext |= E1000_CTRL_EXT_RO_DIS; + E1000_WRITE_REG(hw, E1000_CTRL_EXT, ctrl_ext); + } + + return ret_val; +} + +/** + * e1000_setup_copper_link_82540 - Configure copper link settings + * @hw: pointer to the HW structure + * + * Calls the appropriate function to configure the link for auto-neg or forced + * speed and duplex. Then we check for link, once link is established calls + * to configure collision distance and flow control are called. If link is + * not established, we return -E1000_ERR_PHY (-2). + **/ +static s32 e1000_setup_copper_link_82540(struct e1000_hw *hw) +{ + u32 ctrl; + s32 ret_val = E1000_SUCCESS; + u16 data; + + DEBUGFUNC("e1000_setup_copper_link_82540"); + + ctrl = E1000_READ_REG(hw, E1000_CTRL); + ctrl |= E1000_CTRL_SLU; + ctrl &= ~(E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX); + E1000_WRITE_REG(hw, E1000_CTRL, ctrl); + + ret_val = e1000_set_phy_mode_82540(hw); + if (ret_val) + goto out; + + if (hw->mac.type == e1000_82545_rev_3 || + hw->mac.type == e1000_82546_rev_3) { + ret_val = hw->phy.ops.read_reg(hw, M88E1000_PHY_SPEC_CTRL, &data); + if (ret_val) + goto out; + data |= 0x00000008; + ret_val = hw->phy.ops.write_reg(hw, M88E1000_PHY_SPEC_CTRL, data); + if (ret_val) + goto out; + } + + ret_val = e1000_copper_link_setup_m88(hw); + if (ret_val) + goto out; + + ret_val = e1000_setup_copper_link_generic(hw); + +out: + return ret_val; +} + +/** + * e1000_setup_fiber_serdes_link_82540 - Setup link for fiber/serdes + * @hw: pointer to the HW structure + * + * Set the output amplitude to the value in the EEPROM and adjust the VCO + * speed to improve Bit Error Rate (BER) performance. Configures collision + * distance and flow control for fiber and serdes links. Upon successful + * setup, poll for link. + **/ +static s32 e1000_setup_fiber_serdes_link_82540(struct e1000_hw *hw) +{ + struct e1000_mac_info *mac = &hw->mac; + s32 ret_val = E1000_SUCCESS; + + DEBUGFUNC("e1000_setup_fiber_serdes_link_82540"); + + switch (mac->type) { + case e1000_82545_rev_3: + case e1000_82546_rev_3: + if (hw->phy.media_type == e1000_media_type_internal_serdes) { + /* + * If we're on serdes media, adjust the output + * amplitude to value set in the EEPROM. + */ + ret_val = e1000_adjust_serdes_amplitude_82540(hw); + if (ret_val) + goto out; + } + /* Adjust VCO speed to improve BER performance */ + ret_val = e1000_set_vco_speed_82540(hw); + if (ret_val) + goto out; + default: + break; + } + + ret_val = e1000_setup_fiber_serdes_link_generic(hw); + +out: + return ret_val; +} + +/** + * e1000_adjust_serdes_amplitude_82540 - Adjust amplitude based on EEPROM + * @hw: pointer to the HW structure + * + * Adjust the SERDES output amplitude based on the EEPROM settings. + **/ +static s32 e1000_adjust_serdes_amplitude_82540(struct e1000_hw *hw) +{ + s32 ret_val = E1000_SUCCESS; + u16 nvm_data; + + DEBUGFUNC("e1000_adjust_serdes_amplitude_82540"); + + ret_val = hw->nvm.ops.read(hw, NVM_SERDES_AMPLITUDE, 1, &nvm_data); + if (ret_val) + goto out; + + if (nvm_data != NVM_RESERVED_WORD) { + /* Adjust serdes output amplitude only. */ + nvm_data &= NVM_SERDES_AMPLITUDE_MASK; + ret_val = hw->phy.ops.write_reg(hw, + M88E1000_PHY_EXT_CTRL, + nvm_data); + if (ret_val) + goto out; + } + +out: + return ret_val; +} + +/** + * e1000_set_vco_speed_82540 - Set VCO speed for better performance + * @hw: pointer to the HW structure + * + * Set the VCO speed to improve Bit Error Rate (BER) performance. + **/ +static s32 e1000_set_vco_speed_82540(struct e1000_hw *hw) +{ + s32 ret_val = E1000_SUCCESS; + u16 default_page = 0; + u16 phy_data; + + DEBUGFUNC("e1000_set_vco_speed_82540"); + + /* Set PHY register 30, page 5, bit 8 to 0 */ + + ret_val = hw->phy.ops.read_reg(hw, + M88E1000_PHY_PAGE_SELECT, + &default_page); + if (ret_val) + goto out; + + ret_val = hw->phy.ops.write_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x0005); + if (ret_val) + goto out; + + ret_val = hw->phy.ops.read_reg(hw, M88E1000_PHY_GEN_CONTROL, &phy_data); + if (ret_val) + goto out; + + phy_data &= ~M88E1000_PHY_VCO_REG_BIT8; + ret_val = hw->phy.ops.write_reg(hw, M88E1000_PHY_GEN_CONTROL, phy_data); + if (ret_val) + goto out; + + /* Set PHY register 30, page 4, bit 11 to 1 */ + + ret_val = hw->phy.ops.write_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x0004); + if (ret_val) + goto out; + + ret_val = hw->phy.ops.read_reg(hw, M88E1000_PHY_GEN_CONTROL, &phy_data); + if (ret_val) + goto out; + + phy_data |= M88E1000_PHY_VCO_REG_BIT11; + ret_val = hw->phy.ops.write_reg(hw, M88E1000_PHY_GEN_CONTROL, phy_data); + if (ret_val) + goto out; + + ret_val = hw->phy.ops.write_reg(hw, M88E1000_PHY_PAGE_SELECT, + default_page); + +out: + return ret_val; +} + +/** + * e1000_set_phy_mode_82540 - Set PHY to class A mode + * @hw: pointer to the HW structure + * + * Sets the PHY to class A mode and assumes the following operations will + * follow to enable the new class mode: + * 1. Do a PHY soft reset. + * 2. Restart auto-negotiation or force link. + **/ +static s32 e1000_set_phy_mode_82540(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val = E1000_SUCCESS; + u16 nvm_data; + + DEBUGFUNC("e1000_set_phy_mode_82540"); + + if (hw->mac.type != e1000_82545_rev_3) + goto out; + + ret_val = hw->nvm.ops.read(hw, NVM_PHY_CLASS_WORD, 1, &nvm_data); + if (ret_val) { + ret_val = -E1000_ERR_PHY; + goto out; + } + + if ((nvm_data != NVM_RESERVED_WORD) && (nvm_data & NVM_PHY_CLASS_A)) { + ret_val = hw->phy.ops.write_reg(hw, M88E1000_PHY_PAGE_SELECT, + 0x000B); + if (ret_val) { + ret_val = -E1000_ERR_PHY; + goto out; + } + ret_val = hw->phy.ops.write_reg(hw, + M88E1000_PHY_GEN_CONTROL, + 0x8104); + if (ret_val) { + ret_val = -E1000_ERR_PHY; + goto out; + } + + phy->reset_disable = FALSE; + } + +out: + return ret_val; +} + +/** + * e1000_power_down_phy_copper_82540 - Remove link in case of PHY power down + * @hw: pointer to the HW structure + * + * In the case of a PHY power down to save power, or to turn off link during a + * driver unload, or wake on lan is not enabled, remove the link. + **/ +static void e1000_power_down_phy_copper_82540(struct e1000_hw *hw) +{ + /* If the management interface is not enabled, then power down */ + if (!(E1000_READ_REG(hw, E1000_MANC) & E1000_MANC_SMBUS_EN)) + e1000_power_down_phy_copper(hw); + + return; +} + +/** + * e1000_clear_hw_cntrs_82540 - Clear device specific hardware counters + * @hw: pointer to the HW structure + * + * Clears the hardware counters by reading the counter registers. + **/ +static void e1000_clear_hw_cntrs_82540(struct e1000_hw *hw) +{ + DEBUGFUNC("e1000_clear_hw_cntrs_82540"); + + e1000_clear_hw_cntrs_base_generic(hw); + + E1000_READ_REG(hw, E1000_PRC64); + E1000_READ_REG(hw, E1000_PRC127); + E1000_READ_REG(hw, E1000_PRC255); + E1000_READ_REG(hw, E1000_PRC511); + E1000_READ_REG(hw, E1000_PRC1023); + E1000_READ_REG(hw, E1000_PRC1522); + E1000_READ_REG(hw, E1000_PTC64); + E1000_READ_REG(hw, E1000_PTC127); + E1000_READ_REG(hw, E1000_PTC255); + E1000_READ_REG(hw, E1000_PTC511); + E1000_READ_REG(hw, E1000_PTC1023); + E1000_READ_REG(hw, E1000_PTC1522); + + E1000_READ_REG(hw, E1000_ALGNERRC); + E1000_READ_REG(hw, E1000_RXERRC); + E1000_READ_REG(hw, E1000_TNCRS); + E1000_READ_REG(hw, E1000_CEXTERR); + E1000_READ_REG(hw, E1000_TSCTC); + E1000_READ_REG(hw, E1000_TSCTFC); + + E1000_READ_REG(hw, E1000_MGTPRC); + E1000_READ_REG(hw, E1000_MGTPDC); + E1000_READ_REG(hw, E1000_MGTPTC); +} + diff --git a/sys/dev/netif/ig_hal/e1000_82541.c b/sys/dev/netif/ig_hal/e1000_82541.c new file mode 100644 index 0000000000..03d11036f7 --- /dev/null +++ b/sys/dev/netif/ig_hal/e1000_82541.c @@ -0,0 +1,1283 @@ +/****************************************************************************** + + Copyright (c) 2001-2008, Intel Corporation + All rights reserved. + + Redistribution and use in source and binary forms, with or without + modification, are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, + this list of conditions and the following disclaimer. + + 2. Redistributions in binary form must reproduce the above copyright + notice, this list of conditions and the following disclaimer in the + documentation and/or other materials provided with the distribution. + + 3. Neither the name of the Intel Corporation nor the names of its + contributors may be used to endorse or promote products derived from + this software without specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE + ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE + LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR + CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF + SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS + INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN + CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) + ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + POSSIBILITY OF SUCH DAMAGE. + +******************************************************************************/ +/*$FreeBSD$*/ + +/* + * 82541EI Gigabit Ethernet Controller + * 82541ER Gigabit Ethernet Controller + * 82541GI Gigabit Ethernet Controller + * 82541PI Gigabit Ethernet Controller + * 82547EI Gigabit Ethernet Controller + * 82547GI Gigabit Ethernet Controller + */ + +#include "e1000_api.h" + +static s32 e1000_init_phy_params_82541(struct e1000_hw *hw); +static s32 e1000_init_nvm_params_82541(struct e1000_hw *hw); +static s32 e1000_init_mac_params_82541(struct e1000_hw *hw); +static s32 e1000_reset_hw_82541(struct e1000_hw *hw); +static s32 e1000_init_hw_82541(struct e1000_hw *hw); +static s32 e1000_get_link_up_info_82541(struct e1000_hw *hw, u16 *speed, + u16 *duplex); +static s32 e1000_phy_hw_reset_82541(struct e1000_hw *hw); +static s32 e1000_setup_copper_link_82541(struct e1000_hw *hw); +static s32 e1000_check_for_link_82541(struct e1000_hw *hw); +static s32 e1000_get_cable_length_igp_82541(struct e1000_hw *hw); +static s32 e1000_set_d3_lplu_state_82541(struct e1000_hw *hw, + bool active); +static s32 e1000_setup_led_82541(struct e1000_hw *hw); +static s32 e1000_cleanup_led_82541(struct e1000_hw *hw); +static void e1000_clear_hw_cntrs_82541(struct e1000_hw *hw); +static s32 e1000_config_dsp_after_link_change_82541(struct e1000_hw *hw, + bool link_up); +static s32 e1000_phy_init_script_82541(struct e1000_hw *hw); +static void e1000_power_down_phy_copper_82541(struct e1000_hw *hw); + +static const u16 e1000_igp_cable_length_table[] = + { 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, + 5, 10, 10, 10, 10, 10, 10, 10, 20, 20, 20, 20, 20, 25, 25, 25, + 25, 25, 25, 25, 30, 30, 30, 30, 40, 40, 40, 40, 40, 40, 40, 40, + 40, 50, 50, 50, 50, 50, 50, 50, 60, 60, 60, 60, 60, 60, 60, 60, + 60, 70, 70, 70, 70, 70, 70, 80, 80, 80, 80, 80, 80, 90, 90, 90, + 90, 90, 90, 90, 90, 90, 100, 100, 100, 100, 100, 100, 100, 100, 100, 100, + 100, 100, 100, 100, 110, 110, 110, 110, 110, 110, 110, 110, 110, 110, 110, 110, + 110, 110, 110, 110, 110, 110, 120, 120, 120, 120, 120, 120, 120, 120, 120, 120}; +#define IGP01E1000_AGC_LENGTH_TABLE_SIZE \ + (sizeof(e1000_igp_cable_length_table) / \ + sizeof(e1000_igp_cable_length_table[0])) + +/** + * e1000_init_phy_params_82541 - Init PHY func ptrs. + * @hw: pointer to the HW structure + **/ +static s32 e1000_init_phy_params_82541(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val = E1000_SUCCESS; + + DEBUGFUNC("e1000_init_phy_params_82541"); + + phy->addr = 1; + phy->autoneg_mask = AUTONEG_ADVERTISE_SPEED_DEFAULT; + phy->reset_delay_us = 10000; + phy->type = e1000_phy_igp; + + /* Function Pointers */ + phy->ops.check_polarity = e1000_check_polarity_igp; + phy->ops.force_speed_duplex = e1000_phy_force_speed_duplex_igp; + phy->ops.get_cable_length = e1000_get_cable_length_igp_82541; + phy->ops.get_cfg_done = e1000_get_cfg_done_generic; + phy->ops.get_info = e1000_get_phy_info_igp; + phy->ops.read_reg = e1000_read_phy_reg_igp; + phy->ops.reset = e1000_phy_hw_reset_82541; + phy->ops.set_d3_lplu_state = e1000_set_d3_lplu_state_82541; + phy->ops.write_reg = e1000_write_phy_reg_igp; + phy->ops.power_up = e1000_power_up_phy_copper; + phy->ops.power_down = e1000_power_down_phy_copper_82541; + + ret_val = e1000_get_phy_id(hw); + if (ret_val) + goto out; + + /* Verify phy id */ + if (phy->id != IGP01E1000_I_PHY_ID) { + ret_val = -E1000_ERR_PHY; + goto out; + } + +out: + return ret_val; +} + +/** + * e1000_init_nvm_params_82541 - Init NVM func ptrs. + * @hw: pointer to the HW structure + **/ +static s32 e1000_init_nvm_params_82541(struct e1000_hw *hw) +{ + struct e1000_nvm_info *nvm = &hw->nvm; + s32 ret_val = E1000_SUCCESS; + u32 eecd = E1000_READ_REG(hw, E1000_EECD); + u16 size; + + DEBUGFUNC("e1000_init_nvm_params_82541"); + + switch (nvm->override) { + case e1000_nvm_override_spi_large: + nvm->type = e1000_nvm_eeprom_spi; + eecd |= E1000_EECD_ADDR_BITS; + break; + case e1000_nvm_override_spi_small: + nvm->type = e1000_nvm_eeprom_spi; + eecd &= ~E1000_EECD_ADDR_BITS; + break; + case e1000_nvm_override_microwire_large: + nvm->type = e1000_nvm_eeprom_microwire; + eecd |= E1000_EECD_SIZE; + break; + case e1000_nvm_override_microwire_small: + nvm->type = e1000_nvm_eeprom_microwire; + eecd &= ~E1000_EECD_SIZE; + break; + default: + nvm->type = eecd & E1000_EECD_TYPE + ? e1000_nvm_eeprom_spi + : e1000_nvm_eeprom_microwire; + break; + } + + if (nvm->type == e1000_nvm_eeprom_spi) { + nvm->address_bits = (eecd & E1000_EECD_ADDR_BITS) + ? 16 : 8; + nvm->delay_usec = 1; + nvm->opcode_bits = 8; + nvm->page_size = (eecd & E1000_EECD_ADDR_BITS) + ? 32 : 8; + + /* Function Pointers */ + nvm->ops.acquire = e1000_acquire_nvm_generic; + nvm->ops.read = e1000_read_nvm_spi; + nvm->ops.release = e1000_release_nvm_generic; + nvm->ops.update = e1000_update_nvm_checksum_generic; + nvm->ops.valid_led_default = e1000_valid_led_default_generic; + nvm->ops.validate = e1000_validate_nvm_checksum_generic; + nvm->ops.write = e1000_write_nvm_spi; + + /* + * nvm->word_size must be discovered after the pointers + * are set so we can verify the size from the nvm image + * itself. Temporarily set it to a dummy value so the + * read will work. + */ + nvm->word_size = 64; + ret_val = nvm->ops.read(hw, NVM_CFG, 1, &size); + if (ret_val) + goto out; + size = (size & NVM_SIZE_MASK) >> NVM_SIZE_SHIFT; + /* + * if size != 0, it can be added to a constant and become + * the left-shift value to set the word_size. Otherwise, + * word_size stays at 64. + */ + if (size) { + size += NVM_WORD_SIZE_BASE_SHIFT_82541; + nvm->word_size = 1 << size; + } + } else { + nvm->address_bits = (eecd & E1000_EECD_ADDR_BITS) + ? 8 : 6; + nvm->delay_usec = 50; + nvm->opcode_bits = 3; + nvm->word_size = (eecd & E1000_EECD_ADDR_BITS) + ? 256 : 64; + + /* Function Pointers */ + nvm->ops.acquire = e1000_acquire_nvm_generic; + nvm->ops.read = e1000_read_nvm_microwire; + nvm->ops.release = e1000_release_nvm_generic; + nvm->ops.update = e1000_update_nvm_checksum_generic; + nvm->ops.valid_led_default = e1000_valid_led_default_generic; + nvm->ops.validate = e1000_validate_nvm_checksum_generic; + nvm->ops.write = e1000_write_nvm_microwire; + } + +out: + return ret_val; +} + +/** + * e1000_init_mac_params_82541 - Init MAC func ptrs. + * @hw: pointer to the HW structure + **/ +static s32 e1000_init_mac_params_82541(struct e1000_hw *hw) +{ + struct e1000_mac_info *mac = &hw->mac; + + DEBUGFUNC("e1000_init_mac_params_82541"); + + /* Set media type */ + hw->phy.media_type = e1000_media_type_copper; + /* Set mta register count */ + mac->mta_reg_count = 128; + /* Set rar entry count */ + mac->rar_entry_count = E1000_RAR_ENTRIES; + /* Set if part includes ASF firmware */ + mac->asf_firmware_present = TRUE; + + /* Function Pointers */ + + /* bus type/speed/width */ + mac->ops.get_bus_info = e1000_get_bus_info_pci_generic; + /* function id */ + mac->ops.set_lan_id = e1000_set_lan_id_single_port; + /* reset */ + mac->ops.reset_hw = e1000_reset_hw_82541; + /* hw initialization */ + mac->ops.init_hw = e1000_init_hw_82541; + /* link setup */ + mac->ops.setup_link = e1000_setup_link_generic; + /* physical interface link setup */ + mac->ops.setup_physical_interface = e1000_setup_copper_link_82541; + /* check for link */ + mac->ops.check_for_link = e1000_check_for_link_82541; + /* link info */ + mac->ops.get_link_up_info = e1000_get_link_up_info_82541; + /* multicast address update */ + mac->ops.update_mc_addr_list = e1000_update_mc_addr_list_generic; + /* writing VFTA */ + mac->ops.write_vfta = e1000_write_vfta_generic; + /* clearing VFTA */ + mac->ops.clear_vfta = e1000_clear_vfta_generic; + /* setting MTA */ + mac->ops.mta_set = e1000_mta_set_generic; + /* setup LED */ + mac->ops.setup_led = e1000_setup_led_82541; + /* cleanup LED */ + mac->ops.cleanup_led = e1000_cleanup_led_82541; + /* turn on/off LED */ + mac->ops.led_on = e1000_led_on_generic; + mac->ops.led_off = e1000_led_off_generic; + /* clear hardware counters */ + mac->ops.clear_hw_cntrs = e1000_clear_hw_cntrs_82541; + + return E1000_SUCCESS; +} + +/** + * e1000_init_function_pointers_82541 - Init func ptrs. + * @hw: pointer to the HW structure + * + * Called to initialize all function pointers and parameters. + **/ +void e1000_init_function_pointers_82541(struct e1000_hw *hw) +{ + DEBUGFUNC("e1000_init_function_pointers_82541"); + + hw->mac.ops.init_params = e1000_init_mac_params_82541; + hw->nvm.ops.init_params = e1000_init_nvm_params_82541; + hw->phy.ops.init_params = e1000_init_phy_params_82541; +} + +/** + * e1000_reset_hw_82541 - Reset hardware + * @hw: pointer to the HW structure + * + * This resets the hardware into a known state. + **/ +static s32 e1000_reset_hw_82541(struct e1000_hw *hw) +{ + u32 ledctl, ctrl, icr, manc; + + DEBUGFUNC("e1000_reset_hw_82541"); + + DEBUGOUT("Masking off all interrupts\n"); + E1000_WRITE_REG(hw, E1000_IMC, 0xFFFFFFFF); + + E1000_WRITE_REG(hw, E1000_RCTL, 0); + E1000_WRITE_REG(hw, E1000_TCTL, E1000_TCTL_PSP); + E1000_WRITE_FLUSH(hw); + + /* + * Delay to allow any outstanding PCI transactions to complete + * before resetting the device. + */ + msec_delay(10); + + ctrl = E1000_READ_REG(hw, E1000_CTRL); + + /* Must reset the Phy before resetting the MAC */ + if ((hw->mac.type == e1000_82541) || (hw->mac.type == e1000_82547)) { + E1000_WRITE_REG(hw, E1000_CTRL, (ctrl | E1000_CTRL_PHY_RST)); + msec_delay(5); + } + + DEBUGOUT("Issuing a global reset to 82541/82547 MAC\n"); + switch (hw->mac.type) { + case e1000_82541: + case e1000_82541_rev_2: + /* + * These controllers can't ack the 64-bit write when + * issuing the reset, so we use IO-mapping as a + * workaround to issue the reset. + */ + E1000_WRITE_REG_IO(hw, E1000_CTRL, ctrl | E1000_CTRL_RST); + break; + default: + E1000_WRITE_REG(hw, E1000_CTRL, ctrl | E1000_CTRL_RST); + break; + } + + /* Wait for NVM reload */ + msec_delay(20); + + /* Disable HW ARPs on ASF enabled adapters */ + manc = E1000_READ_REG(hw, E1000_MANC); + manc &= ~E1000_MANC_ARP_EN; + E1000_WRITE_REG(hw, E1000_MANC, manc); + + if ((hw->mac.type == e1000_82541) || (hw->mac.type == e1000_82547)) { + e1000_phy_init_script_82541(hw); + + /* Configure activity LED after Phy reset */ + ledctl = E1000_READ_REG(hw, E1000_LEDCTL); + ledctl &= IGP_ACTIVITY_LED_MASK; + ledctl |= (IGP_ACTIVITY_LED_ENABLE | IGP_LED3_MODE); + E1000_WRITE_REG(hw, E1000_LEDCTL, ledctl); + } + + /* Once again, mask the interrupts */ + DEBUGOUT("Masking off all interrupts\n"); + E1000_WRITE_REG(hw, E1000_IMC, 0xFFFFFFFF); + + /* Clear any pending interrupt events. */ + icr = E1000_READ_REG(hw, E1000_ICR); + + return E1000_SUCCESS; +} + +/** + * e1000_init_hw_82541 - Initialize hardware + * @hw: pointer to the HW structure + * + * This inits the hardware readying it for operation. + **/ +static s32 e1000_init_hw_82541(struct e1000_hw *hw) +{ + struct e1000_mac_info *mac = &hw->mac; + u32 i, txdctl; + s32 ret_val; + + DEBUGFUNC("e1000_init_hw_82541"); + + /* Initialize identification LED */ + ret_val = e1000_id_led_init_generic(hw); + if (ret_val) { + DEBUGOUT("Error initializing identification LED\n"); + /* This is not fatal and we should not stop init due to this */ + } + + /* Disabling VLAN filtering */ + DEBUGOUT("Initializing the IEEE VLAN\n"); + mac->ops.clear_vfta(hw); + + /* Setup the receive address. */ + e1000_init_rx_addrs_generic(hw, mac->rar_entry_count); + + /* Zero out the Multicast HASH table */ + DEBUGOUT("Zeroing the MTA\n"); + for (i = 0; i < mac->mta_reg_count; i++) { + E1000_WRITE_REG_ARRAY(hw, E1000_MTA, i, 0); + /* + * Avoid back to back register writes by adding the register + * read (flush). This is to protect against some strange + * bridge configurations that may issue Memory Write Block + * (MWB) to our register space. + */ + E1000_WRITE_FLUSH(hw); + } + + /* Setup link and flow control */ + ret_val = mac->ops.setup_link(hw); + + txdctl = E1000_READ_REG(hw, E1000_TXDCTL(0)); + txdctl = (txdctl & ~E1000_TXDCTL_WTHRESH) | + E1000_TXDCTL_FULL_TX_DESC_WB; + E1000_WRITE_REG(hw, E1000_TXDCTL(0), txdctl); + + /* + * Clear all of the statistics registers (clear on read). It is + * important that we do this after we have tried to establish link + * because the symbol error count will increment wildly if there + * is no link. + */ + e1000_clear_hw_cntrs_82541(hw); + + return ret_val; +} + +/** + * e1000_get_link_up_info_82541 - Report speed and duplex + * @hw: pointer to the HW structure + * @speed: pointer to speed buffer + * @duplex: pointer to duplex buffer + * + * Retrieve the current speed and duplex configuration. + **/ +static s32 e1000_get_link_up_info_82541(struct e1000_hw *hw, u16 *speed, + u16 *duplex) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val; + u16 data; + + DEBUGFUNC("e1000_get_link_up_info_82541"); + + ret_val = e1000_get_speed_and_duplex_copper_generic(hw, speed, duplex); + if (ret_val) + goto out; + + if (!phy->speed_downgraded) + goto out; + + /* + * IGP01 PHY may advertise full duplex operation after speed + * downgrade even if it is operating at half duplex. + * Here we set the duplex settings to match the duplex in the + * link partner's capabilities. + */ + ret_val = phy->ops.read_reg(hw, PHY_AUTONEG_EXP, &data); + if (ret_val) + goto out; + + if (!(data & NWAY_ER_LP_NWAY_CAPS)) { + *duplex = HALF_DUPLEX; + } else { + ret_val = phy->ops.read_reg(hw, PHY_LP_ABILITY, &data); + if (ret_val) + goto out; + + if (*speed == SPEED_100) { + if (!(data & NWAY_LPAR_100TX_FD_CAPS)) + *duplex = HALF_DUPLEX; + } else if (*speed == SPEED_10) { + if (!(data & NWAY_LPAR_10T_FD_CAPS)) + *duplex = HALF_DUPLEX; + } + } + +out: + return ret_val; +} + +/** + * e1000_phy_hw_reset_82541 - PHY hardware reset + * @hw: pointer to the HW structure + * + * Verify the reset block is not blocking us from resetting. Acquire + * semaphore (if necessary) and read/set/write the device control reset + * bit in the PHY. Wait the appropriate delay time for the device to + * reset and release the semaphore (if necessary). + **/ +static s32 e1000_phy_hw_reset_82541(struct e1000_hw *hw) +{ + s32 ret_val; + u32 ledctl; + + DEBUGFUNC("e1000_phy_hw_reset_82541"); + + ret_val = e1000_phy_hw_reset_generic(hw); + if (ret_val) + goto out; + + e1000_phy_init_script_82541(hw); + + if ((hw->mac.type == e1000_82541) || (hw->mac.type == e1000_82547)) { + /* Configure activity LED after PHY reset */ + ledctl = E1000_READ_REG(hw, E1000_LEDCTL); + ledctl &= IGP_ACTIVITY_LED_MASK; + ledctl |= (IGP_ACTIVITY_LED_ENABLE | IGP_LED3_MODE); + E1000_WRITE_REG(hw, E1000_LEDCTL, ledctl); + } + +out: + return ret_val; +} + +/** + * e1000_setup_copper_link_82541 - Configure copper link settings + * @hw: pointer to the HW structure + * + * Calls the appropriate function to configure the link for auto-neg or forced + * speed and duplex. Then we check for link, once link is established calls + * to configure collision distance and flow control are called. If link is + * not established, we return -E1000_ERR_PHY (-2). + **/ +static s32 e1000_setup_copper_link_82541(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + struct e1000_dev_spec_82541 *dev_spec = &hw->dev_spec._82541; + s32 ret_val; + u32 ctrl, ledctl; + + DEBUGFUNC("e1000_setup_copper_link_82541"); + + ctrl = E1000_READ_REG(hw, E1000_CTRL); + ctrl |= E1000_CTRL_SLU; + ctrl &= ~(E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX); + E1000_WRITE_REG(hw, E1000_CTRL, ctrl); + + hw->phy.reset_disable = FALSE; + + /* Earlier revs of the IGP phy require us to force MDI. */ + if (hw->mac.type == e1000_82541 || hw->mac.type == e1000_82547) { + dev_spec->dsp_config = e1000_dsp_config_disabled; + phy->mdix = 1; + } else { + dev_spec->dsp_config = e1000_dsp_config_enabled; + } + + ret_val = e1000_copper_link_setup_igp(hw); + if (ret_val) + goto out; + + if (hw->mac.autoneg) { + if (dev_spec->ffe_config == e1000_ffe_config_active) + dev_spec->ffe_config = e1000_ffe_config_enabled; + } + + /* Configure activity LED after Phy reset */ + ledctl = E1000_READ_REG(hw, E1000_LEDCTL); + ledctl &= IGP_ACTIVITY_LED_MASK; + ledctl |= (IGP_ACTIVITY_LED_ENABLE | IGP_LED3_MODE); + E1000_WRITE_REG(hw, E1000_LEDCTL, ledctl); + + ret_val = e1000_setup_copper_link_generic(hw); + +out: + return ret_val; +} + +/** + * e1000_check_for_link_82541 - Check/Store link connection + * @hw: pointer to the HW structure + * + * This checks the link condition of the adapter and stores the + * results in the hw->mac structure. + **/ +static s32 e1000_check_for_link_82541(struct e1000_hw *hw) +{ + struct e1000_mac_info *mac = &hw->mac; + s32 ret_val; + bool link; + + DEBUGFUNC("e1000_check_for_link_82541"); + + /* + * We only want to go out to the PHY registers to see if Auto-Neg + * has completed and/or if our link status has changed. The + * get_link_status flag is set upon receiving a Link Status + * Change or Rx Sequence Error interrupt. + */ + if (!mac->get_link_status) { + ret_val = E1000_SUCCESS; + goto out; + } + + /* + * First we want to see if the MII Status Register reports + * link. If so, then we want to get the current speed/duplex + * of the PHY. + */ + ret_val = e1000_phy_has_link_generic(hw, 1, 0, &link); + if (ret_val) + goto out; + + if (!link) { + ret_val = e1000_config_dsp_after_link_change_82541(hw, FALSE); + goto out; /* No link detected */ + } + + mac->get_link_status = FALSE; + + /* + * Check if there was DownShift, must be checked + * immediately after link-up + */ + e1000_check_downshift_generic(hw); + + /* + * If we are forcing speed/duplex, then we simply return since + * we have already determined whether we have link or not. + */ + if (!mac->autoneg) { + ret_val = -E1000_ERR_CONFIG; + goto out; + } + + ret_val = e1000_config_dsp_after_link_change_82541(hw, TRUE); + + /* + * Auto-Neg is enabled. Auto Speed Detection takes care + * of MAC speed/duplex configuration. So we only need to + * configure Collision Distance in the MAC. + */ + e1000_config_collision_dist_generic(hw); + + /* + * Configure Flow Control now that Auto-Neg has completed. + * First, we need to restore the desired flow control + * settings because we may have had to re-autoneg with a + * different link partner. + */ + ret_val = e1000_config_fc_after_link_up_generic(hw); + if (ret_val) { + DEBUGOUT("Error configuring flow control\n"); + } + +out: + return ret_val; +} + +/** + * e1000_config_dsp_after_link_change_82541 - Config DSP after link + * @hw: pointer to the HW structure + * @link_up: boolean flag for link up status + * + * Return E1000_ERR_PHY when failing to read/write the PHY, else E1000_SUCCESS + * at any other case. + * + * 82541_rev_2 & 82547_rev_2 have the capability to configure the DSP when a + * gigabit link is achieved to improve link quality. + **/ +static s32 e1000_config_dsp_after_link_change_82541(struct e1000_hw *hw, + bool link_up) +{ + struct e1000_phy_info *phy = &hw->phy; + struct e1000_dev_spec_82541 *dev_spec = &hw->dev_spec._82541; + s32 ret_val; + u32 idle_errs = 0; + u16 phy_data, phy_saved_data, speed, duplex, i; + u16 ffe_idle_err_timeout = FFE_IDLE_ERR_COUNT_TIMEOUT_20; + u16 dsp_reg_array[IGP01E1000_PHY_CHANNEL_NUM] = + {IGP01E1000_PHY_AGC_PARAM_A, + IGP01E1000_PHY_AGC_PARAM_B, + IGP01E1000_PHY_AGC_PARAM_C, + IGP01E1000_PHY_AGC_PARAM_D}; + + DEBUGFUNC("e1000_config_dsp_after_link_change_82541"); + + if (link_up) { + ret_val = hw->mac.ops.get_link_up_info(hw, &speed, &duplex); + if (ret_val) { + DEBUGOUT("Error getting link speed and duplex\n"); + goto out; + } + + if (speed != SPEED_1000) { + ret_val = E1000_SUCCESS; + goto out; + } + + ret_val = phy->ops.get_cable_length(hw); + if (ret_val) + goto out; + + if ((dev_spec->dsp_config == e1000_dsp_config_enabled) && + phy->min_cable_length >= 50) { + + for (i = 0; i < IGP01E1000_PHY_CHANNEL_NUM; i++) { + ret_val = phy->ops.read_reg(hw, + dsp_reg_array[i], + &phy_data); + if (ret_val) + goto out; + + phy_data &= ~IGP01E1000_PHY_EDAC_MU_INDEX; + + ret_val = phy->ops.write_reg(hw, + dsp_reg_array[i], + phy_data); + if (ret_val) + goto out; + } + dev_spec->dsp_config = e1000_dsp_config_activated; + } + + if ((dev_spec->ffe_config != e1000_ffe_config_enabled) || + (phy->min_cable_length >= 50)) { + ret_val = E1000_SUCCESS; + goto out; + } + + /* clear previous idle error counts */ + ret_val = phy->ops.read_reg(hw, PHY_1000T_STATUS, &phy_data); + if (ret_val) + goto out; + + for (i = 0; i < ffe_idle_err_timeout; i++) { + usec_delay(1000); + ret_val = phy->ops.read_reg(hw, + PHY_1000T_STATUS, + &phy_data); + if (ret_val) + goto out; + + idle_errs += (phy_data & SR_1000T_IDLE_ERROR_CNT); + if (idle_errs > SR_1000T_PHY_EXCESSIVE_IDLE_ERR_COUNT) { + dev_spec->ffe_config = e1000_ffe_config_active; + + ret_val = phy->ops.write_reg(hw, + IGP01E1000_PHY_DSP_FFE, + IGP01E1000_PHY_DSP_FFE_CM_CP); + if (ret_val) + goto out; + break; + } + + if (idle_errs) + ffe_idle_err_timeout = + FFE_IDLE_ERR_COUNT_TIMEOUT_100; + } + } else { + if (dev_spec->dsp_config == e1000_dsp_config_activated) { + /* + * Save off the current value of register 0x2F5B + * to be restored at the end of the routines. + */ + ret_val = phy->ops.read_reg(hw, + 0x2F5B, + &phy_saved_data); + if (ret_val) + goto out; + + /* Disable the PHY transmitter */ + ret_val = phy->ops.write_reg(hw, 0x2F5B, 0x0003); + if (ret_val) + goto out; + + msec_delay_irq(20); + + ret_val = phy->ops.write_reg(hw, + 0x0000, + IGP01E1000_IEEE_FORCE_GIG); + if (ret_val) + goto out; + for (i = 0; i < IGP01E1000_PHY_CHANNEL_NUM; i++) { + ret_val = phy->ops.read_reg(hw, + dsp_reg_array[i], + &phy_data); + if (ret_val) + goto out; + + phy_data &= ~IGP01E1000_PHY_EDAC_MU_INDEX; + phy_data |= IGP01E1000_PHY_EDAC_SIGN_EXT_9_BITS; + + ret_val = phy->ops.write_reg(hw, + dsp_reg_array[i], + phy_data); + if (ret_val) + goto out; + } + + ret_val = phy->ops.write_reg(hw, + 0x0000, + IGP01E1000_IEEE_RESTART_AUTONEG); + if (ret_val) + goto out; + + msec_delay_irq(20); + + /* Now enable the transmitter */ + ret_val = phy->ops.write_reg(hw, + 0x2F5B, + phy_saved_data); + if (ret_val) + goto out; + + dev_spec->dsp_config = e1000_dsp_config_enabled; + } + + if (dev_spec->ffe_config != e1000_ffe_config_active) { + ret_val = E1000_SUCCESS; + goto out; + } + + /* + * Save off the current value of register 0x2F5B + * to be restored at the end of the routines. + */ + ret_val = phy->ops.read_reg(hw, 0x2F5B, &phy_saved_data); + if (ret_val) + goto out; + + /* Disable the PHY transmitter */ + ret_val = phy->ops.write_reg(hw, 0x2F5B, 0x0003); + if (ret_val) + goto out; + + msec_delay_irq(20); + + ret_val = phy->ops.write_reg(hw, + 0x0000, + IGP01E1000_IEEE_FORCE_GIG); + if (ret_val) + goto out; + + ret_val = phy->ops.write_reg(hw, + IGP01E1000_PHY_DSP_FFE, + IGP01E1000_PHY_DSP_FFE_DEFAULT); + if (ret_val) + goto out; + + ret_val = phy->ops.write_reg(hw, + 0x0000, + IGP01E1000_IEEE_RESTART_AUTONEG); + if (ret_val) + goto out; + + msec_delay_irq(20); + + /* Now enable the transmitter */ + ret_val = phy->ops.write_reg(hw, 0x2F5B, phy_saved_data); + + if (ret_val) + goto out; + + dev_spec->ffe_config = e1000_ffe_config_enabled; + } + +out: + return ret_val; +} + +/** + * e1000_get_cable_length_igp_82541 - Determine cable length for igp PHY + * @hw: pointer to the HW structure + * + * The automatic gain control (agc) normalizes the amplitude of the + * received signal, adjusting for the attenuation produced by the + * cable. By reading the AGC registers, which represent the + * combination of coarse and fine gain value, the value can be put + * into a lookup table to obtain the approximate cable length + * for each channel. + **/ +static s32 e1000_get_cable_length_igp_82541(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val = E1000_SUCCESS; + u16 i, data; + u16 cur_agc_value, agc_value = 0; + u16 min_agc_value = IGP01E1000_AGC_LENGTH_TABLE_SIZE; + u16 agc_reg_array[IGP01E1000_PHY_CHANNEL_NUM] = + {IGP01E1000_PHY_AGC_A, + IGP01E1000_PHY_AGC_B, + IGP01E1000_PHY_AGC_C, + IGP01E1000_PHY_AGC_D}; + + DEBUGFUNC("e1000_get_cable_length_igp_82541"); + + /* Read the AGC registers for all channels */ + for (i = 0; i < IGP01E1000_PHY_CHANNEL_NUM; i++) { + ret_val = phy->ops.read_reg(hw, agc_reg_array[i], &data); + if (ret_val) + goto out; + + cur_agc_value = data >> IGP01E1000_AGC_LENGTH_SHIFT; + + /* Bounds checking */ + if ((cur_agc_value >= IGP01E1000_AGC_LENGTH_TABLE_SIZE - 1) || + (cur_agc_value == 0)) { + ret_val = -E1000_ERR_PHY; + goto out; + } + + agc_value += cur_agc_value; + + if (min_agc_value > cur_agc_value) + min_agc_value = cur_agc_value; + } + + /* Remove the minimal AGC result for length < 50m */ + if (agc_value < IGP01E1000_PHY_CHANNEL_NUM * 50) { + agc_value -= min_agc_value; + /* Average the three remaining channels for the length. */ + agc_value /= (IGP01E1000_PHY_CHANNEL_NUM - 1); + } else { + /* Average the channels for the length. */ + agc_value /= IGP01E1000_PHY_CHANNEL_NUM; + } + + phy->min_cable_length = (e1000_igp_cable_length_table[agc_value] > + IGP01E1000_AGC_RANGE) + ? (e1000_igp_cable_length_table[agc_value] - + IGP01E1000_AGC_RANGE) + : 0; + phy->max_cable_length = e1000_igp_cable_length_table[agc_value] + + IGP01E1000_AGC_RANGE; + + phy->cable_length = (phy->min_cable_length + phy->max_cable_length) / 2; + +out: + return ret_val; +} + +/** + * e1000_set_d3_lplu_state_82541 - Sets low power link up state for D3 + * @hw: pointer to the HW structure + * @active: boolean used to enable/disable lplu + * + * Success returns 0, Failure returns 1 + * + * The low power link up (lplu) state is set to the power management level D3 + * and SmartSpeed is disabled when active is TRUE, else clear lplu for D3 + * and enable Smartspeed. LPLU and Smartspeed are mutually exclusive. LPLU + * is used during Dx states where the power conservation is most important. + * During driver activity, SmartSpeed should be enabled so performance is + * maintained. + **/ +static s32 e1000_set_d3_lplu_state_82541(struct e1000_hw *hw, bool active) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val; + u16 data; + + DEBUGFUNC("e1000_set_d3_lplu_state_82541"); + + switch (hw->mac.type) { + case e1000_82541_rev_2: + case e1000_82547_rev_2: + break; + default: + ret_val = e1000_set_d3_lplu_state_generic(hw, active); + goto out; + break; + } + + ret_val = phy->ops.read_reg(hw, IGP01E1000_GMII_FIFO, &data); + if (ret_val) + goto out; + + if (!active) { + data &= ~IGP01E1000_GMII_FLEX_SPD; + ret_val = phy->ops.write_reg(hw, IGP01E1000_GMII_FIFO, data); + if (ret_val) + goto out; + + /* + * LPLU and SmartSpeed are mutually exclusive. LPLU is used + * during Dx states where the power conservation is most + * important. During driver activity we should enable + * SmartSpeed, so performance is maintained. + */ + if (phy->smart_speed == e1000_smart_speed_on) { + ret_val = phy->ops.read_reg(hw, + IGP01E1000_PHY_PORT_CONFIG, + &data); + if (ret_val) + goto out; + + data |= IGP01E1000_PSCFR_SMART_SPEED; + ret_val = phy->ops.write_reg(hw, + IGP01E1000_PHY_PORT_CONFIG, + data); + if (ret_val) + goto out; + } else if (phy->smart_speed == e1000_smart_speed_off) { + ret_val = phy->ops.read_reg(hw, + IGP01E1000_PHY_PORT_CONFIG, + &data); + if (ret_val) + goto out; + + data &= ~IGP01E1000_PSCFR_SMART_SPEED; + ret_val = phy->ops.write_reg(hw, + IGP01E1000_PHY_PORT_CONFIG, + data); + if (ret_val) + goto out; + } + } else if ((phy->autoneg_advertised == E1000_ALL_SPEED_DUPLEX) || + (phy->autoneg_advertised == E1000_ALL_NOT_GIG) || + (phy->autoneg_advertised == E1000_ALL_10_SPEED)) { + data |= IGP01E1000_GMII_FLEX_SPD; + ret_val = phy->ops.write_reg(hw, IGP01E1000_GMII_FIFO, data); + if (ret_val) + goto out; + + /* When LPLU is enabled, we should disable SmartSpeed */ + ret_val = phy->ops.read_reg(hw, + IGP01E1000_PHY_PORT_CONFIG, + &data); + if (ret_val) + goto out; + + data &= ~IGP01E1000_PSCFR_SMART_SPEED; + ret_val = phy->ops.write_reg(hw, + IGP01E1000_PHY_PORT_CONFIG, + data); + } + +out: + return ret_val; +} + +/** + * e1000_setup_led_82541 - Configures SW controllable LED + * @hw: pointer to the HW structure + * + * This prepares the SW controllable LED for use and saves the current state + * of the LED so it can be later restored. + **/ +static s32 e1000_setup_led_82541(struct e1000_hw *hw) +{ + struct e1000_dev_spec_82541 *dev_spec = &hw->dev_spec._82541; + s32 ret_val; + + DEBUGFUNC("e1000_setup_led_82541"); + + ret_val = hw->phy.ops.read_reg(hw, + IGP01E1000_GMII_FIFO, + &dev_spec->spd_default); + if (ret_val) + goto out; + + ret_val = hw->phy.ops.write_reg(hw, + IGP01E1000_GMII_FIFO, + (u16)(dev_spec->spd_default & + ~IGP01E1000_GMII_SPD)); + if (ret_val) + goto out; + + E1000_WRITE_REG(hw, E1000_LEDCTL, hw->mac.ledctl_mode1); + +out: + return ret_val; +} + +/** + * e1000_cleanup_led_82541 - Set LED config to default operation + * @hw: pointer to the HW structure + * + * Remove the current LED configuration and set the LED configuration + * to the default value, saved from the EEPROM. + **/ +static s32 e1000_cleanup_led_82541(struct e1000_hw *hw) +{ + struct e1000_dev_spec_82541 *dev_spec = &hw->dev_spec._82541; + s32 ret_val; + + DEBUGFUNC("e1000_cleanup_led_82541"); + + ret_val = hw->phy.ops.write_reg(hw, + IGP01E1000_GMII_FIFO, + dev_spec->spd_default); + if (ret_val) + goto out; + + E1000_WRITE_REG(hw, E1000_LEDCTL, hw->mac.ledctl_default); + +out: + return ret_val; +} + +/** + * e1000_phy_init_script_82541 - Initialize GbE PHY + * @hw: pointer to the HW structure + * + * Initializes the IGP PHY. + **/ +static s32 e1000_phy_init_script_82541(struct e1000_hw *hw) +{ + struct e1000_dev_spec_82541 *dev_spec = &hw->dev_spec._82541; + u32 ret_val; + u16 phy_saved_data; + + DEBUGFUNC("e1000_phy_init_script_82541"); + + if (!dev_spec->phy_init_script) { + ret_val = E1000_SUCCESS; + goto out; + } + + /* Delay after phy reset to enable NVM configuration to load */ + msec_delay(20); + + /* + * Save off the current value of register 0x2F5B to be restored at + * the end of this routine. + */ + ret_val = hw->phy.ops.read_reg(hw, 0x2F5B, &phy_saved_data); + + /* Disabled the PHY transmitter */ + hw->phy.ops.write_reg(hw, 0x2F5B, 0x0003); + + msec_delay(20); + + hw->phy.ops.write_reg(hw, 0x0000, 0x0140); + + msec_delay(5); + + switch (hw->mac.type) { + case e1000_82541: + case e1000_82547: + hw->phy.ops.write_reg(hw, 0x1F95, 0x0001); + + hw->phy.ops.write_reg(hw, 0x1F71, 0xBD21); + + hw->phy.ops.write_reg(hw, 0x1F79, 0x0018); + + hw->phy.ops.write_reg(hw, 0x1F30, 0x1600); + + hw->phy.ops.write_reg(hw, 0x1F31, 0x0014); + + hw->phy.ops.write_reg(hw, 0x1F32, 0x161C); + + hw->phy.ops.write_reg(hw, 0x1F94, 0x0003); + + hw->phy.ops.write_reg(hw, 0x1F96, 0x003F); + + hw->phy.ops.write_reg(hw, 0x2010, 0x0008); + break; + case e1000_82541_rev_2: + case e1000_82547_rev_2: + hw->phy.ops.write_reg(hw, 0x1F73, 0x0099); + break; + default: + break; + } + + hw->phy.ops.write_reg(hw, 0x0000, 0x3300); + + msec_delay(20); + + /* Now enable the transmitter */ + hw->phy.ops.write_reg(hw, 0x2F5B, phy_saved_data); + + if (hw->mac.type == e1000_82547) { + u16 fused, fine, coarse; + + /* Move to analog registers page */ + hw->phy.ops.read_reg(hw, + IGP01E1000_ANALOG_SPARE_FUSE_STATUS, + &fused); + + if (!(fused & IGP01E1000_ANALOG_SPARE_FUSE_ENABLED)) { + hw->phy.ops.read_reg(hw, + IGP01E1000_ANALOG_FUSE_STATUS, + &fused); + + fine = fused & IGP01E1000_ANALOG_FUSE_FINE_MASK; + coarse = fused & IGP01E1000_ANALOG_FUSE_COARSE_MASK; + + if (coarse > IGP01E1000_ANALOG_FUSE_COARSE_THRESH) { + coarse -= IGP01E1000_ANALOG_FUSE_COARSE_10; + fine -= IGP01E1000_ANALOG_FUSE_FINE_1; + } else if (coarse == + IGP01E1000_ANALOG_FUSE_COARSE_THRESH) + fine -= IGP01E1000_ANALOG_FUSE_FINE_10; + + fused = (fused & IGP01E1000_ANALOG_FUSE_POLY_MASK) | + (fine & IGP01E1000_ANALOG_FUSE_FINE_MASK) | + (coarse & IGP01E1000_ANALOG_FUSE_COARSE_MASK); + + hw->phy.ops.write_reg(hw, + IGP01E1000_ANALOG_FUSE_CONTROL, + fused); + hw->phy.ops.write_reg(hw, + IGP01E1000_ANALOG_FUSE_BYPASS, + IGP01E1000_ANALOG_FUSE_ENABLE_SW_CONTROL); + } + } + +out: + return ret_val; +} + +/** + * e1000_init_script_state_82541 - Enable/Disable PHY init script + * @hw: pointer to the HW structure + * @state: boolean value used to enable/disable PHY init script + * + * Allows the driver to enable/disable the PHY init script, if the PHY is an + * IGP PHY. + **/ +void e1000_init_script_state_82541(struct e1000_hw *hw, bool state) +{ + struct e1000_dev_spec_82541 *dev_spec = &hw->dev_spec._82541; + + DEBUGFUNC("e1000_init_script_state_82541"); + + if (hw->phy.type != e1000_phy_igp) { + DEBUGOUT("Initialization script not necessary.\n"); + goto out; + } + + dev_spec->phy_init_script = state; + +out: + return; +} + +/** + * e1000_power_down_phy_copper_82541 - Remove link in case of PHY power down + * @hw: pointer to the HW structure + * + * In the case of a PHY power down to save power, or to turn off link during a + * driver unload, or wake on lan is not enabled, remove the link. + **/ +static void e1000_power_down_phy_copper_82541(struct e1000_hw *hw) +{ + /* If the management interface is not enabled, then power down */ + if (!(E1000_READ_REG(hw, E1000_MANC) & E1000_MANC_SMBUS_EN)) + e1000_power_down_phy_copper(hw); + + return; +} + +/** + * e1000_clear_hw_cntrs_82541 - Clear device specific hardware counters + * @hw: pointer to the HW structure + * + * Clears the hardware counters by reading the counter registers. + **/ +static void e1000_clear_hw_cntrs_82541(struct e1000_hw *hw) +{ + DEBUGFUNC("e1000_clear_hw_cntrs_82541"); + + e1000_clear_hw_cntrs_base_generic(hw); + + E1000_READ_REG(hw, E1000_PRC64); + E1000_READ_REG(hw, E1000_PRC127); + E1000_READ_REG(hw, E1000_PRC255); + E1000_READ_REG(hw, E1000_PRC511); + E1000_READ_REG(hw, E1000_PRC1023); + E1000_READ_REG(hw, E1000_PRC1522); + E1000_READ_REG(hw, E1000_PTC64); + E1000_READ_REG(hw, E1000_PTC127); + E1000_READ_REG(hw, E1000_PTC255); + E1000_READ_REG(hw, E1000_PTC511); + E1000_READ_REG(hw, E1000_PTC1023); + E1000_READ_REG(hw, E1000_PTC1522); + + E1000_READ_REG(hw, E1000_ALGNERRC); + E1000_READ_REG(hw, E1000_RXERRC); + E1000_READ_REG(hw, E1000_TNCRS); + E1000_READ_REG(hw, E1000_CEXTERR); + E1000_READ_REG(hw, E1000_TSCTC); + E1000_READ_REG(hw, E1000_TSCTFC); + + E1000_READ_REG(hw, E1000_MGTPRC); + E1000_READ_REG(hw, E1000_MGTPDC); + E1000_READ_REG(hw, E1000_MGTPTC); +} diff --git a/sys/dev/netif/ig_hal/e1000_82541.h b/sys/dev/netif/ig_hal/e1000_82541.h new file mode 100644 index 0000000000..3b6b9612ee --- /dev/null +++ b/sys/dev/netif/ig_hal/e1000_82541.h @@ -0,0 +1,92 @@ +/****************************************************************************** + + Copyright (c) 2001-2008, Intel Corporation + All rights reserved. + + Redistribution and use in source and binary forms, with or without + modification, are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, + this list of conditions and the following disclaimer. + + 2. Redistributions in binary form must reproduce the above copyright + notice, this list of conditions and the following disclaimer in the + documentation and/or other materials provided with the distribution. + + 3. Neither the name of the Intel Corporation nor the names of its + contributors may be used to endorse or promote products derived from + this software without specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE + ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE + LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR + CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF + SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS + INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN + CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) + ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + POSSIBILITY OF SUCH DAMAGE. + +******************************************************************************/ +/*$FreeBSD$*/ + +#ifndef _E1000_82541_H_ +#define _E1000_82541_H_ + +#define NVM_WORD_SIZE_BASE_SHIFT_82541 (NVM_WORD_SIZE_BASE_SHIFT + 1) + +#define IGP01E1000_PHY_CHANNEL_NUM 4 + +#define IGP01E1000_PHY_AGC_A 0x1172 +#define IGP01E1000_PHY_AGC_B 0x1272 +#define IGP01E1000_PHY_AGC_C 0x1472 +#define IGP01E1000_PHY_AGC_D 0x1872 + +#define IGP01E1000_PHY_AGC_PARAM_A 0x1171 +#define IGP01E1000_PHY_AGC_PARAM_B 0x1271 +#define IGP01E1000_PHY_AGC_PARAM_C 0x1471 +#define IGP01E1000_PHY_AGC_PARAM_D 0x1871 + +#define IGP01E1000_PHY_EDAC_MU_INDEX 0xC000 +#define IGP01E1000_PHY_EDAC_SIGN_EXT_9_BITS 0x8000 + +#define IGP01E1000_PHY_DSP_RESET 0x1F33 + +#define IGP01E1000_PHY_DSP_FFE 0x1F35 +#define IGP01E1000_PHY_DSP_FFE_CM_CP 0x0069 +#define IGP01E1000_PHY_DSP_FFE_DEFAULT 0x002A + +#define IGP01E1000_IEEE_FORCE_GIG 0x0140 +#define IGP01E1000_IEEE_RESTART_AUTONEG 0x3300 + +#define IGP01E1000_AGC_LENGTH_SHIFT 7 +#define IGP01E1000_AGC_RANGE 10 + +#define FFE_IDLE_ERR_COUNT_TIMEOUT_20 20 +#define FFE_IDLE_ERR_COUNT_TIMEOUT_100 100 + +#define IGP01E1000_ANALOG_FUSE_STATUS 0x20D0 +#define IGP01E1000_ANALOG_SPARE_FUSE_STATUS 0x20D1 +#define IGP01E1000_ANALOG_FUSE_CONTROL 0x20DC +#define IGP01E1000_ANALOG_FUSE_BYPASS 0x20DE + +#define IGP01E1000_ANALOG_SPARE_FUSE_ENABLED 0x0100 +#define IGP01E1000_ANALOG_FUSE_FINE_MASK 0x0F80 +#define IGP01E1000_ANALOG_FUSE_COARSE_MASK 0x0070 +#define IGP01E1000_ANALOG_FUSE_COARSE_THRESH 0x0040 +#define IGP01E1000_ANALOG_FUSE_COARSE_10 0x0010 +#define IGP01E1000_ANALOG_FUSE_FINE_1 0x0080 +#define IGP01E1000_ANALOG_FUSE_FINE_10 0x0500 +#define IGP01E1000_ANALOG_FUSE_POLY_MASK 0xF000 +#define IGP01E1000_ANALOG_FUSE_ENABLE_SW_CONTROL 0x0002 + +#define IGP01E1000_MSE_CHANNEL_D 0x000F +#define IGP01E1000_MSE_CHANNEL_C 0x00F0 +#define IGP01E1000_MSE_CHANNEL_B 0x0F00 +#define IGP01E1000_MSE_CHANNEL_A 0xF000 + + +void e1000_init_script_state_82541(struct e1000_hw *hw, bool state); +#endif diff --git a/sys/dev/netif/ig_hal/e1000_82542.c b/sys/dev/netif/ig_hal/e1000_82542.c new file mode 100644 index 0000000000..3ce36575f9 --- /dev/null +++ b/sys/dev/netif/ig_hal/e1000_82542.c @@ -0,0 +1,556 @@ +/****************************************************************************** + + Copyright (c) 2001-2008, Intel Corporation + All rights reserved. + + Redistribution and use in source and binary forms, with or without + modification, are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, + this list of conditions and the following disclaimer. + + 2. Redistributions in binary form must reproduce the above copyright + notice, this list of conditions and the following disclaimer in the + documentation and/or other materials provided with the distribution. + + 3. Neither the name of the Intel Corporation nor the names of its + contributors may be used to endorse or promote products derived from + this software without specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE + ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE + LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR + CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF + SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS + INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN + CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) + ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + POSSIBILITY OF SUCH DAMAGE. + +******************************************************************************/ +/*$FreeBSD$*/ + +/* + * 82542 Gigabit Ethernet Controller + */ + +#include "e1000_api.h" + +static s32 e1000_init_phy_params_82542(struct e1000_hw *hw); +static s32 e1000_init_nvm_params_82542(struct e1000_hw *hw); +static s32 e1000_init_mac_params_82542(struct e1000_hw *hw); +static s32 e1000_get_bus_info_82542(struct e1000_hw *hw); +static s32 e1000_reset_hw_82542(struct e1000_hw *hw); +static s32 e1000_init_hw_82542(struct e1000_hw *hw); +static s32 e1000_setup_link_82542(struct e1000_hw *hw); +static s32 e1000_led_on_82542(struct e1000_hw *hw); +static s32 e1000_led_off_82542(struct e1000_hw *hw); +static void e1000_rar_set_82542(struct e1000_hw *hw, u8 *addr, u32 index); +static void e1000_clear_hw_cntrs_82542(struct e1000_hw *hw); + +/** + * e1000_init_phy_params_82542 - Init PHY func ptrs. + * @hw: pointer to the HW structure + **/ +static s32 e1000_init_phy_params_82542(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val = E1000_SUCCESS; + + DEBUGFUNC("e1000_init_phy_params_82542"); + + phy->type = e1000_phy_none; + + return ret_val; +} + +/** + * e1000_init_nvm_params_82542 - Init NVM func ptrs. + * @hw: pointer to the HW structure + **/ +static s32 e1000_init_nvm_params_82542(struct e1000_hw *hw) +{ + struct e1000_nvm_info *nvm = &hw->nvm; + + DEBUGFUNC("e1000_init_nvm_params_82542"); + + nvm->address_bits = 6; + nvm->delay_usec = 50; + nvm->opcode_bits = 3; + nvm->type = e1000_nvm_eeprom_microwire; + nvm->word_size = 64; + + /* Function Pointers */ + nvm->ops.read = e1000_read_nvm_microwire; + nvm->ops.release = e1000_stop_nvm; + nvm->ops.write = e1000_write_nvm_microwire; + nvm->ops.update = e1000_update_nvm_checksum_generic; + nvm->ops.validate = e1000_validate_nvm_checksum_generic; + + return E1000_SUCCESS; +} + +/** + * e1000_init_mac_params_82542 - Init MAC func ptrs. + * @hw: pointer to the HW structure + **/ +static s32 e1000_init_mac_params_82542(struct e1000_hw *hw) +{ + struct e1000_mac_info *mac = &hw->mac; + + DEBUGFUNC("e1000_init_mac_params_82542"); + + /* Set media type */ + hw->phy.media_type = e1000_media_type_fiber; + + /* Set mta register count */ + mac->mta_reg_count = 128; + /* Set rar entry count */ + mac->rar_entry_count = E1000_RAR_ENTRIES; + + /* Function pointers */ + + /* bus type/speed/width */ + mac->ops.get_bus_info = e1000_get_bus_info_82542; + /* function id */ + mac->ops.set_lan_id = e1000_set_lan_id_multi_port_pci; + /* reset */ + mac->ops.reset_hw = e1000_reset_hw_82542; + /* hw initialization */ + mac->ops.init_hw = e1000_init_hw_82542; + /* link setup */ + mac->ops.setup_link = e1000_setup_link_82542; + /* phy/fiber/serdes setup */ + mac->ops.setup_physical_interface = e1000_setup_fiber_serdes_link_generic; + /* check for link */ + mac->ops.check_for_link = e1000_check_for_fiber_link_generic; + /* multicast address update */ + mac->ops.update_mc_addr_list = e1000_update_mc_addr_list_generic; + /* writing VFTA */ + mac->ops.write_vfta = e1000_write_vfta_generic; + /* clearing VFTA */ + mac->ops.clear_vfta = e1000_clear_vfta_generic; + /* setting MTA */ + mac->ops.mta_set = e1000_mta_set_generic; + /* set RAR */ + mac->ops.rar_set = e1000_rar_set_82542; + /* turn on/off LED */ + mac->ops.led_on = e1000_led_on_82542; + mac->ops.led_off = e1000_led_off_82542; + /* clear hardware counters */ + mac->ops.clear_hw_cntrs = e1000_clear_hw_cntrs_82542; + /* link info */ + mac->ops.get_link_up_info = e1000_get_speed_and_duplex_fiber_serdes_generic; + + return E1000_SUCCESS; +} + +/** + * e1000_init_function_pointers_82542 - Init func ptrs. + * @hw: pointer to the HW structure + * + * Called to initialize all function pointers and parameters. + **/ +void e1000_init_function_pointers_82542(struct e1000_hw *hw) +{ + DEBUGFUNC("e1000_init_function_pointers_82542"); + + hw->mac.ops.init_params = e1000_init_mac_params_82542; + hw->nvm.ops.init_params = e1000_init_nvm_params_82542; + hw->phy.ops.init_params = e1000_init_phy_params_82542; +} + +/** + * e1000_get_bus_info_82542 - Obtain bus information for adapter + * @hw: pointer to the HW structure + * + * This will obtain information about the HW bus for which the + * adapter is attached and stores it in the hw structure. + **/ +static s32 e1000_get_bus_info_82542(struct e1000_hw *hw) +{ + DEBUGFUNC("e1000_get_bus_info_82542"); + + hw->bus.type = e1000_bus_type_pci; + hw->bus.speed = e1000_bus_speed_unknown; + hw->bus.width = e1000_bus_width_unknown; + + return E1000_SUCCESS; +} + +/** + * e1000_reset_hw_82542 - Reset hardware + * @hw: pointer to the HW structure + * + * This resets the hardware into a known state. + **/ +static s32 e1000_reset_hw_82542(struct e1000_hw *hw) +{ + struct e1000_bus_info *bus = &hw->bus; + s32 ret_val = E1000_SUCCESS; + u32 ctrl, icr; + + DEBUGFUNC("e1000_reset_hw_82542"); + + if (hw->revision_id == E1000_REVISION_2) { + DEBUGOUT("Disabling MWI on 82542 rev 2\n"); + e1000_pci_clear_mwi(hw); + } + + DEBUGOUT("Masking off all interrupts\n"); + E1000_WRITE_REG(hw, E1000_IMC, 0xffffffff); + + E1000_WRITE_REG(hw, E1000_RCTL, 0); + E1000_WRITE_REG(hw, E1000_TCTL, E1000_TCTL_PSP); + E1000_WRITE_FLUSH(hw); + + /* + * Delay to allow any outstanding PCI transactions to complete before + * resetting the device + */ + msec_delay(10); + + ctrl = E1000_READ_REG(hw, E1000_CTRL); + + DEBUGOUT("Issuing a global reset to 82542/82543 MAC\n"); + E1000_WRITE_REG(hw, E1000_CTRL, ctrl | E1000_CTRL_RST); + + hw->nvm.ops.reload(hw); + msec_delay(2); + + E1000_WRITE_REG(hw, E1000_IMC, 0xffffffff); + icr = E1000_READ_REG(hw, E1000_ICR); + + if (hw->revision_id == E1000_REVISION_2) { + if (bus->pci_cmd_word & CMD_MEM_WRT_INVALIDATE) + e1000_pci_set_mwi(hw); + } + + return ret_val; +} + +/** + * e1000_init_hw_82542 - Initialize hardware + * @hw: pointer to the HW structure + * + * This inits the hardware readying it for operation. + **/ +static s32 e1000_init_hw_82542(struct e1000_hw *hw) +{ + struct e1000_mac_info *mac = &hw->mac; + struct e1000_dev_spec_82542 *dev_spec = &hw->dev_spec._82542; + s32 ret_val = E1000_SUCCESS; + u32 ctrl; + u16 i; + + DEBUGFUNC("e1000_init_hw_82542"); + + /* Disabling VLAN filtering */ + E1000_WRITE_REG(hw, E1000_VET, 0); + mac->ops.clear_vfta(hw); + + /* For 82542 (rev 2.0), disable MWI and put the receiver into reset */ + if (hw->revision_id == E1000_REVISION_2) { + DEBUGOUT("Disabling MWI on 82542 rev 2.0\n"); + e1000_pci_clear_mwi(hw); + E1000_WRITE_REG(hw, E1000_RCTL, E1000_RCTL_RST); + E1000_WRITE_FLUSH(hw); + msec_delay(5); + } + + /* Setup the receive address. */ + e1000_init_rx_addrs_generic(hw, mac->rar_entry_count); + + /* For 82542 (rev 2.0), take the receiver out of reset and enable MWI */ + if (hw->revision_id == E1000_REVISION_2) { + E1000_WRITE_REG(hw, E1000_RCTL, 0); + E1000_WRITE_FLUSH(hw); + msec_delay(1); + if (hw->bus.pci_cmd_word & CMD_MEM_WRT_INVALIDATE) + e1000_pci_set_mwi(hw); + } + + /* Zero out the Multicast HASH table */ + DEBUGOUT("Zeroing the MTA\n"); + for (i = 0; i < mac->mta_reg_count; i++) + E1000_WRITE_REG_ARRAY(hw, E1000_MTA, i, 0); + + /* + * Set the PCI priority bit correctly in the CTRL register. This + * determines if the adapter gives priority to receives, or if it + * gives equal priority to transmits and receives. + */ + if (dev_spec->dma_fairness) { + ctrl = E1000_READ_REG(hw, E1000_CTRL); + E1000_WRITE_REG(hw, E1000_CTRL, ctrl | E1000_CTRL_PRIOR); + } + + /* Setup link and flow control */ + ret_val = e1000_setup_link_82542(hw); + + /* + * Clear all of the statistics registers (clear on read). It is + * important that we do this after we have tried to establish link + * because the symbol error count will increment wildly if there + * is no link. + */ + e1000_clear_hw_cntrs_82542(hw); + + return ret_val; +} + +/** + * e1000_setup_link_82542 - Setup flow control and link settings + * @hw: pointer to the HW structure + * + * Determines which flow control settings to use, then configures flow + * control. Calls the appropriate media-specific link configuration + * function. Assuming the adapter has a valid link partner, a valid link + * should be established. Assumes the hardware has previously been reset + * and the transmitter and receiver are not enabled. + **/ +static s32 e1000_setup_link_82542(struct e1000_hw *hw) +{ + struct e1000_mac_info *mac = &hw->mac; + s32 ret_val = E1000_SUCCESS; + + DEBUGFUNC("e1000_setup_link_82542"); + + ret_val = e1000_set_default_fc_generic(hw); + if (ret_val) + goto out; + + hw->fc.requested_mode &= ~e1000_fc_tx_pause; + + if (mac->report_tx_early == 1) + hw->fc.requested_mode &= ~e1000_fc_rx_pause; + + /* + * Save off the requested flow control mode for use later. Depending + * on the link partner's capabilities, we may or may not use this mode. + */ + hw->fc.current_mode = hw->fc.requested_mode; + + DEBUGOUT1("After fix-ups FlowControl is now = %x\n", + hw->fc.current_mode); + + /* Call the necessary subroutine to configure the link. */ + ret_val = mac->ops.setup_physical_interface(hw); + if (ret_val) + goto out; + + /* + * Initialize the flow control address, type, and PAUSE timer + * registers to their default values. This is done even if flow + * control is disabled, because it does not hurt anything to + * initialize these registers. + */ + DEBUGOUT("Initializing Flow Control address, type and timer regs\n"); + + E1000_WRITE_REG(hw, E1000_FCAL, FLOW_CONTROL_ADDRESS_LOW); + E1000_WRITE_REG(hw, E1000_FCAH, FLOW_CONTROL_ADDRESS_HIGH); + E1000_WRITE_REG(hw, E1000_FCT, FLOW_CONTROL_TYPE); + + E1000_WRITE_REG(hw, E1000_FCTTV, hw->fc.pause_time); + + ret_val = e1000_set_fc_watermarks_generic(hw); + +out: + return ret_val; +} + +/** + * e1000_led_on_82542 - Turn on SW controllable LED + * @hw: pointer to the HW structure + * + * Turns the SW defined LED on. + **/ +static s32 e1000_led_on_82542(struct e1000_hw *hw) +{ + u32 ctrl = E1000_READ_REG(hw, E1000_CTRL); + + DEBUGFUNC("e1000_led_on_82542"); + + ctrl |= E1000_CTRL_SWDPIN0; + ctrl |= E1000_CTRL_SWDPIO0; + E1000_WRITE_REG(hw, E1000_CTRL, ctrl); + + return E1000_SUCCESS; +} + +/** + * e1000_led_off_82542 - Turn off SW controllable LED + * @hw: pointer to the HW structure + * + * Turns the SW defined LED off. + **/ +static s32 e1000_led_off_82542(struct e1000_hw *hw) +{ + u32 ctrl = E1000_READ_REG(hw, E1000_CTRL); + + DEBUGFUNC("e1000_led_off_82542"); + + ctrl &= ~E1000_CTRL_SWDPIN0; + ctrl |= E1000_CTRL_SWDPIO0; + E1000_WRITE_REG(hw, E1000_CTRL, ctrl); + + return E1000_SUCCESS; +} + +/** + * e1000_rar_set_82542 - Set receive address register + * @hw: pointer to the HW structure + * @addr: pointer to the receive address + * @index: receive address array register + * + * Sets the receive address array register at index to the address passed + * in by addr. + **/ +static void e1000_rar_set_82542(struct e1000_hw *hw, u8 *addr, u32 index) +{ + u32 rar_low, rar_high; + + DEBUGFUNC("e1000_rar_set_82542"); + + /* + * HW expects these in little endian so we reverse the byte order + * from network order (big endian) to little endian + */ + rar_low = ((u32) addr[0] | + ((u32) addr[1] << 8) | + ((u32) addr[2] << 16) | ((u32) addr[3] << 24)); + + rar_high = ((u32) addr[4] | ((u32) addr[5] << 8)); + + /* If MAC address zero, no need to set the AV bit */ + if (rar_low || rar_high) + rar_high |= E1000_RAH_AV; + + E1000_WRITE_REG_ARRAY(hw, E1000_RA, (index << 1), rar_low); + E1000_WRITE_REG_ARRAY(hw, E1000_RA, ((index << 1) + 1), rar_high); +} + +/** + * e1000_translate_register_82542 - Translate the proper register offset + * @reg: e1000 register to be read + * + * Registers in 82542 are located in different offsets than other adapters + * even though they function in the same manner. This function takes in + * the name of the register to read and returns the correct offset for + * 82542 silicon. + **/ +u32 e1000_translate_register_82542(u32 reg) +{ + /* + * Some of the 82542 registers are located at different + * offsets than they are in newer adapters. + * Despite the difference in location, the registers + * function in the same manner. + */ + switch (reg) { + case E1000_RA: + reg = 0x00040; + break; + case E1000_RDTR: + reg = 0x00108; + break; + case E1000_RDBAL(0): + reg = 0x00110; + break; + case E1000_RDBAH(0): + reg = 0x00114; + break; + case E1000_RDLEN(0): + reg = 0x00118; + break; + case E1000_RDH(0): + reg = 0x00120; + break; + case E1000_RDT(0): + reg = 0x00128; + break; + case E1000_RDBAL(1): + reg = 0x00138; + break; + case E1000_RDBAH(1): + reg = 0x0013C; + break; + case E1000_RDLEN(1): + reg = 0x00140; + break; + case E1000_RDH(1): + reg = 0x00148; + break; + case E1000_RDT(1): + reg = 0x00150; + break; + case E1000_FCRTH: + reg = 0x00160; + break; + case E1000_FCRTL: + reg = 0x00168; + break; + case E1000_MTA: + reg = 0x00200; + break; + case E1000_TDBAL(0): + reg = 0x00420; + break; + case E1000_TDBAH(0): + reg = 0x00424; + break; + case E1000_TDLEN(0): + reg = 0x00428; + break; + case E1000_TDH(0): + reg = 0x00430; + break; + case E1000_TDT(0): + reg = 0x00438; + break; + case E1000_TIDV: + reg = 0x00440; + break; + case E1000_VFTA: + reg = 0x00600; + break; + case E1000_TDFH: + reg = 0x08010; + break; + case E1000_TDFT: + reg = 0x08018; + break; + default: + break; + } + + return reg; +} + +/** + * e1000_clear_hw_cntrs_82542 - Clear device specific hardware counters + * @hw: pointer to the HW structure + * + * Clears the hardware counters by reading the counter registers. + **/ +static void e1000_clear_hw_cntrs_82542(struct e1000_hw *hw) +{ + DEBUGFUNC("e1000_clear_hw_cntrs_82542"); + + e1000_clear_hw_cntrs_base_generic(hw); + + E1000_READ_REG(hw, E1000_PRC64); + E1000_READ_REG(hw, E1000_PRC127); + E1000_READ_REG(hw, E1000_PRC255); + E1000_READ_REG(hw, E1000_PRC511); + E1000_READ_REG(hw, E1000_PRC1023); + E1000_READ_REG(hw, E1000_PRC1522); + E1000_READ_REG(hw, E1000_PTC64); + E1000_READ_REG(hw, E1000_PTC127); + E1000_READ_REG(hw, E1000_PTC255); + E1000_READ_REG(hw, E1000_PTC511); + E1000_READ_REG(hw, E1000_PTC1023); + E1000_READ_REG(hw, E1000_PTC1522); +} diff --git a/sys/dev/netif/ig_hal/e1000_82543.c b/sys/dev/netif/ig_hal/e1000_82543.c new file mode 100644 index 0000000000..97c7f3b204 --- /dev/null +++ b/sys/dev/netif/ig_hal/e1000_82543.c @@ -0,0 +1,1602 @@ +/****************************************************************************** + + Copyright (c) 2001-2008, Intel Corporation + All rights reserved. + + Redistribution and use in source and binary forms, with or without + modification, are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, + this list of conditions and the following disclaimer. + + 2. Redistributions in binary form must reproduce the above copyright + notice, this list of conditions and the following disclaimer in the + documentation and/or other materials provided with the distribution. + + 3. Neither the name of the Intel Corporation nor the names of its + contributors may be used to endorse or promote products derived from + this software without specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE + ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE + LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR + CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF + SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS + INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN + CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) + ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + POSSIBILITY OF SUCH DAMAGE. + +******************************************************************************/ +/*$FreeBSD$*/ + +/* + * 82543GC Gigabit Ethernet Controller (Fiber) + * 82543GC Gigabit Ethernet Controller (Copper) + * 82544EI Gigabit Ethernet Controller (Copper) + * 82544EI Gigabit Ethernet Controller (Fiber) + * 82544GC Gigabit Ethernet Controller (Copper) + * 82544GC Gigabit Ethernet Controller (LOM) + */ + +#include "e1000_api.h" + +static s32 e1000_init_phy_params_82543(struct e1000_hw *hw); +static s32 e1000_init_nvm_params_82543(struct e1000_hw *hw); +static s32 e1000_init_mac_params_82543(struct e1000_hw *hw); +static s32 e1000_read_phy_reg_82543(struct e1000_hw *hw, u32 offset, + u16 *data); +static s32 e1000_write_phy_reg_82543(struct e1000_hw *hw, u32 offset, + u16 data); +static s32 e1000_phy_force_speed_duplex_82543(struct e1000_hw *hw); +static s32 e1000_phy_hw_reset_82543(struct e1000_hw *hw); +static s32 e1000_reset_hw_82543(struct e1000_hw *hw); +static s32 e1000_init_hw_82543(struct e1000_hw *hw); +static s32 e1000_setup_link_82543(struct e1000_hw *hw); +static s32 e1000_setup_copper_link_82543(struct e1000_hw *hw); +static s32 e1000_setup_fiber_link_82543(struct e1000_hw *hw); +static s32 e1000_check_for_copper_link_82543(struct e1000_hw *hw); +static s32 e1000_check_for_fiber_link_82543(struct e1000_hw *hw); +static s32 e1000_led_on_82543(struct e1000_hw *hw); +static s32 e1000_led_off_82543(struct e1000_hw *hw); +static void e1000_write_vfta_82543(struct e1000_hw *hw, u32 offset, + u32 value); +static void e1000_mta_set_82543(struct e1000_hw *hw, u32 hash_value); +static void e1000_clear_hw_cntrs_82543(struct e1000_hw *hw); +static s32 e1000_config_mac_to_phy_82543(struct e1000_hw *hw); +static bool e1000_init_phy_disabled_82543(struct e1000_hw *hw); +static void e1000_lower_mdi_clk_82543(struct e1000_hw *hw, u32 *ctrl); +static s32 e1000_polarity_reversal_workaround_82543(struct e1000_hw *hw); +static void e1000_raise_mdi_clk_82543(struct e1000_hw *hw, u32 *ctrl); +static u16 e1000_shift_in_mdi_bits_82543(struct e1000_hw *hw); +static void e1000_shift_out_mdi_bits_82543(struct e1000_hw *hw, u32 data, + u16 count); +static bool e1000_tbi_compatibility_enabled_82543(struct e1000_hw *hw); +static void e1000_set_tbi_sbp_82543(struct e1000_hw *hw, bool state); + +/** + * e1000_init_phy_params_82543 - Init PHY func ptrs. + * @hw: pointer to the HW structure + **/ +static s32 e1000_init_phy_params_82543(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val = E1000_SUCCESS; + + DEBUGFUNC("e1000_init_phy_params_82543"); + + if (hw->phy.media_type != e1000_media_type_copper) { + phy->type = e1000_phy_none; + goto out; + } else { + phy->ops.power_up = e1000_power_up_phy_copper; + phy->ops.power_down = e1000_power_down_phy_copper; + } + + phy->addr = 1; + phy->autoneg_mask = AUTONEG_ADVERTISE_SPEED_DEFAULT; + phy->reset_delay_us = 10000; + phy->type = e1000_phy_m88; + + /* Function Pointers */ + phy->ops.check_polarity = e1000_check_polarity_m88; + phy->ops.commit = e1000_phy_sw_reset_generic; + phy->ops.force_speed_duplex = e1000_phy_force_speed_duplex_82543; + phy->ops.get_cable_length = e1000_get_cable_length_m88; + phy->ops.get_cfg_done = e1000_get_cfg_done_generic; + phy->ops.read_reg = (hw->mac.type == e1000_82543) + ? e1000_read_phy_reg_82543 + : e1000_read_phy_reg_m88; + phy->ops.reset = (hw->mac.type == e1000_82543) + ? e1000_phy_hw_reset_82543 + : e1000_phy_hw_reset_generic; + phy->ops.write_reg = (hw->mac.type == e1000_82543) + ? e1000_write_phy_reg_82543 + : e1000_write_phy_reg_m88; + phy->ops.get_info = e1000_get_phy_info_m88; + + /* + * The external PHY of the 82543 can be in a funky state. + * Resetting helps us read the PHY registers for acquiring + * the PHY ID. + */ + if (!e1000_init_phy_disabled_82543(hw)) { + ret_val = phy->ops.reset(hw); + if (ret_val) { + DEBUGOUT("Resetting PHY during init failed.\n"); + goto out; + } + msec_delay(20); + } + + ret_val = e1000_get_phy_id(hw); + if (ret_val) + goto out; + + /* Verify phy id */ + switch (hw->mac.type) { + case e1000_82543: + if (phy->id != M88E1000_E_PHY_ID) { + ret_val = -E1000_ERR_PHY; + goto out; + } + break; + case e1000_82544: + if (phy->id != M88E1000_I_PHY_ID) { + ret_val = -E1000_ERR_PHY; + goto out; + } + break; + default: + ret_val = -E1000_ERR_PHY; + goto out; + break; + } + +out: + return ret_val; +} + +/** + * e1000_init_nvm_params_82543 - Init NVM func ptrs. + * @hw: pointer to the HW structure + **/ +static s32 e1000_init_nvm_params_82543(struct e1000_hw *hw) +{ + struct e1000_nvm_info *nvm = &hw->nvm; + + DEBUGFUNC("e1000_init_nvm_params_82543"); + + nvm->type = e1000_nvm_eeprom_microwire; + nvm->word_size = 64; + nvm->delay_usec = 50; + nvm->address_bits = 6; + nvm->opcode_bits = 3; + + /* Function Pointers */ + nvm->ops.read = e1000_read_nvm_microwire; + nvm->ops.update = e1000_update_nvm_checksum_generic; + nvm->ops.valid_led_default = e1000_valid_led_default_generic; + nvm->ops.validate = e1000_validate_nvm_checksum_generic; + nvm->ops.write = e1000_write_nvm_microwire; + + return E1000_SUCCESS; +} + +/** + * e1000_init_mac_params_82543 - Init MAC func ptrs. + * @hw: pointer to the HW structure + **/ +static s32 e1000_init_mac_params_82543(struct e1000_hw *hw) +{ + struct e1000_mac_info *mac = &hw->mac; + + DEBUGFUNC("e1000_init_mac_params_82543"); + + /* Set media type */ + switch (hw->device_id) { + case E1000_DEV_ID_82543GC_FIBER: + case E1000_DEV_ID_82544EI_FIBER: + hw->phy.media_type = e1000_media_type_fiber; + break; + default: + hw->phy.media_type = e1000_media_type_copper; + break; + } + + /* Set mta register count */ + mac->mta_reg_count = 128; + /* Set rar entry count */ + mac->rar_entry_count = E1000_RAR_ENTRIES; + + /* Function pointers */ + + /* bus type/speed/width */ + mac->ops.get_bus_info = e1000_get_bus_info_pci_generic; + /* function id */ + mac->ops.set_lan_id = e1000_set_lan_id_multi_port_pci; + /* reset */ + mac->ops.reset_hw = e1000_reset_hw_82543; + /* hw initialization */ + mac->ops.init_hw = e1000_init_hw_82543; + /* link setup */ + mac->ops.setup_link = e1000_setup_link_82543; + /* physical interface setup */ + mac->ops.setup_physical_interface = + (hw->phy.media_type == e1000_media_type_copper) + ? e1000_setup_copper_link_82543 + : e1000_setup_fiber_link_82543; + /* check for link */ + mac->ops.check_for_link = + (hw->phy.media_type == e1000_media_type_copper) + ? e1000_check_for_copper_link_82543 + : e1000_check_for_fiber_link_82543; + /* link info */ + mac->ops.get_link_up_info = + (hw->phy.media_type == e1000_media_type_copper) + ? e1000_get_speed_and_duplex_copper_generic + : e1000_get_speed_and_duplex_fiber_serdes_generic; + /* multicast address update */ + mac->ops.update_mc_addr_list = e1000_update_mc_addr_list_generic; + /* writing VFTA */ + mac->ops.write_vfta = e1000_write_vfta_82543; + /* clearing VFTA */ + mac->ops.clear_vfta = e1000_clear_vfta_generic; + /* setting MTA */ + mac->ops.mta_set = e1000_mta_set_82543; + /* turn on/off LED */ + mac->ops.led_on = e1000_led_on_82543; + mac->ops.led_off = e1000_led_off_82543; + /* clear hardware counters */ + mac->ops.clear_hw_cntrs = e1000_clear_hw_cntrs_82543; + + /* Set tbi compatibility */ + if ((hw->mac.type != e1000_82543) || + (hw->phy.media_type == e1000_media_type_fiber)) + e1000_set_tbi_compatibility_82543(hw, FALSE); + + return E1000_SUCCESS; +} + +/** + * e1000_init_function_pointers_82543 - Init func ptrs. + * @hw: pointer to the HW structure + * + * Called to initialize all function pointers and parameters. + **/ +void e1000_init_function_pointers_82543(struct e1000_hw *hw) +{ + DEBUGFUNC("e1000_init_function_pointers_82543"); + + hw->mac.ops.init_params = e1000_init_mac_params_82543; + hw->nvm.ops.init_params = e1000_init_nvm_params_82543; + hw->phy.ops.init_params = e1000_init_phy_params_82543; +} + +/** + * e1000_tbi_compatibility_enabled_82543 - Returns TBI compat status + * @hw: pointer to the HW structure + * + * Returns the current status of 10-bit Interface (TBI) compatibility + * (enabled/disabled). + **/ +static bool e1000_tbi_compatibility_enabled_82543(struct e1000_hw *hw) +{ + struct e1000_dev_spec_82543 *dev_spec = &hw->dev_spec._82543; + bool state = FALSE; + + DEBUGFUNC("e1000_tbi_compatibility_enabled_82543"); + + if (hw->mac.type != e1000_82543) { + DEBUGOUT("TBI compatibility workaround for 82543 only.\n"); + goto out; + } + + state = (dev_spec->tbi_compatibility & TBI_COMPAT_ENABLED) + ? TRUE : FALSE; + +out: + return state; +} + +/** + * e1000_set_tbi_compatibility_82543 - Set TBI compatibility + * @hw: pointer to the HW structure + * @state: enable/disable TBI compatibility + * + * Enables or disabled 10-bit Interface (TBI) compatibility. + **/ +void e1000_set_tbi_compatibility_82543(struct e1000_hw *hw, bool state) +{ + struct e1000_dev_spec_82543 *dev_spec = &hw->dev_spec._82543; + + DEBUGFUNC("e1000_set_tbi_compatibility_82543"); + + if (hw->mac.type != e1000_82543) { + DEBUGOUT("TBI compatibility workaround for 82543 only.\n"); + goto out; + } + + if (state) + dev_spec->tbi_compatibility |= TBI_COMPAT_ENABLED; + else + dev_spec->tbi_compatibility &= ~TBI_COMPAT_ENABLED; + +out: + return; +} + +/** + * e1000_tbi_sbp_enabled_82543 - Returns TBI SBP status + * @hw: pointer to the HW structure + * + * Returns the current status of 10-bit Interface (TBI) store bad packet (SBP) + * (enabled/disabled). + **/ +bool e1000_tbi_sbp_enabled_82543(struct e1000_hw *hw) +{ + struct e1000_dev_spec_82543 *dev_spec = &hw->dev_spec._82543; + bool state = FALSE; + + DEBUGFUNC("e1000_tbi_sbp_enabled_82543"); + + if (hw->mac.type != e1000_82543) { + DEBUGOUT("TBI compatibility workaround for 82543 only.\n"); + goto out; + } + + state = (dev_spec->tbi_compatibility & TBI_SBP_ENABLED) + ? TRUE : FALSE; + +out: + return state; +} + +/** + * e1000_set_tbi_sbp_82543 - Set TBI SBP + * @hw: pointer to the HW structure + * @state: enable/disable TBI store bad packet + * + * Enables or disabled 10-bit Interface (TBI) store bad packet (SBP). + **/ +static void e1000_set_tbi_sbp_82543(struct e1000_hw *hw, bool state) +{ + struct e1000_dev_spec_82543 *dev_spec = &hw->dev_spec._82543; + + DEBUGFUNC("e1000_set_tbi_sbp_82543"); + + if (state && e1000_tbi_compatibility_enabled_82543(hw)) + dev_spec->tbi_compatibility |= TBI_SBP_ENABLED; + else + dev_spec->tbi_compatibility &= ~TBI_SBP_ENABLED; + + return; +} + +/** + * e1000_init_phy_disabled_82543 - Returns init PHY status + * @hw: pointer to the HW structure + * + * Returns the current status of whether PHY initialization is disabled. + * True if PHY initialization is disabled else FALSE. + **/ +static bool e1000_init_phy_disabled_82543(struct e1000_hw *hw) +{ + struct e1000_dev_spec_82543 *dev_spec = &hw->dev_spec._82543; + bool ret_val; + + DEBUGFUNC("e1000_init_phy_disabled_82543"); + + if (hw->mac.type != e1000_82543) { + ret_val = FALSE; + goto out; + } + + ret_val = dev_spec->init_phy_disabled; + +out: + return ret_val; +} + +/** + * e1000_tbi_adjust_stats_82543 - Adjust stats when TBI enabled + * @hw: pointer to the HW structure + * @stats: Struct containing statistic register values + * @frame_len: The length of the frame in question + * @mac_addr: The Ethernet destination address of the frame in question + * @max_frame_size: The maximum frame size + * + * Adjusts the statistic counters when a frame is accepted by TBI_ACCEPT + **/ +void e1000_tbi_adjust_stats_82543(struct e1000_hw *hw, + struct e1000_hw_stats *stats, u32 frame_len, + u8 *mac_addr, u32 max_frame_size) +{ + if (!(e1000_tbi_sbp_enabled_82543(hw))) + goto out; + + /* First adjust the frame length. */ + frame_len--; + /* + * We need to adjust the statistics counters, since the hardware + * counters overcount this packet as a CRC error and undercount + * the packet as a good packet + */ + /* This packet should not be counted as a CRC error. */ + stats->crcerrs--; + /* This packet does count as a Good Packet Received. */ + stats->gprc++; + + /* Adjust the Good Octets received counters */ + stats->gorc += frame_len; + + /* + * Is this a broadcast or multicast? Check broadcast first, + * since the test for a multicast frame will test positive on + * a broadcast frame. + */ + if ((mac_addr[0] == 0xff) && (mac_addr[1] == 0xff)) + /* Broadcast packet */ + stats->bprc++; + else if (*mac_addr & 0x01) + /* Multicast packet */ + stats->mprc++; + + /* + * In this case, the hardware has overcounted the number of + * oversize frames. + */ + if ((frame_len == max_frame_size) && (stats->roc > 0)) + stats->roc--; + + /* + * Adjust the bin counters when the extra byte put the frame in the + * wrong bin. Remember that the frame_len was adjusted above. + */ + if (frame_len == 64) { + stats->prc64++; + stats->prc127--; + } else if (frame_len == 127) { + stats->prc127++; + stats->prc255--; + } else if (frame_len == 255) { + stats->prc255++; + stats->prc511--; + } else if (frame_len == 511) { + stats->prc511++; + stats->prc1023--; + } else if (frame_len == 1023) { + stats->prc1023++; + stats->prc1522--; + } else if (frame_len == 1522) { + stats->prc1522++; + } + +out: + return; +} + +/** + * e1000_read_phy_reg_82543 - Read PHY register + * @hw: pointer to the HW structure + * @offset: register offset to be read + * @data: pointer to the read data + * + * Reads the PHY at offset and stores the information read to data. + **/ +static s32 e1000_read_phy_reg_82543(struct e1000_hw *hw, u32 offset, u16 *data) +{ + u32 mdic; + s32 ret_val = E1000_SUCCESS; + + DEBUGFUNC("e1000_read_phy_reg_82543"); + + if (offset > MAX_PHY_REG_ADDRESS) { + DEBUGOUT1("PHY Address %d is out of range\n", offset); + ret_val = -E1000_ERR_PARAM; + goto out; + } + + /* + * We must first send a preamble through the MDIO pin to signal the + * beginning of an MII instruction. This is done by sending 32 + * consecutive "1" bits. + */ + e1000_shift_out_mdi_bits_82543(hw, PHY_PREAMBLE, PHY_PREAMBLE_SIZE); + + /* + * Now combine the next few fields that are required for a read + * operation. We use this method instead of calling the + * e1000_shift_out_mdi_bits routine five different times. The format + * of an MII read instruction consists of a shift out of 14 bits and + * is defined as follows: + * + * followed by a shift in of 18 bits. This first two bits shifted in + * are TurnAround bits used to avoid contention on the MDIO pin when a + * READ operation is performed. These two bits are thrown away + * followed by a shift in of 16 bits which contains the desired data. + */ + mdic = (offset | (hw->phy.addr << 5) | + (PHY_OP_READ << 10) | (PHY_SOF << 12)); + + e1000_shift_out_mdi_bits_82543(hw, mdic, 14); + + /* + * Now that we've shifted out the read command to the MII, we need to + * "shift in" the 16-bit value (18 total bits) of the requested PHY + * register address. + */ + *data = e1000_shift_in_mdi_bits_82543(hw); + +out: + return ret_val; +} + +/** + * e1000_write_phy_reg_82543 - Write PHY register + * @hw: pointer to the HW structure + * @offset: register offset to be written + * @data: pointer to the data to be written at offset + * + * Writes data to the PHY at offset. + **/ +static s32 e1000_write_phy_reg_82543(struct e1000_hw *hw, u32 offset, u16 data) +{ + u32 mdic; + s32 ret_val = E1000_SUCCESS; + + DEBUGFUNC("e1000_write_phy_reg_82543"); + + if (offset > MAX_PHY_REG_ADDRESS) { + DEBUGOUT1("PHY Address %d is out of range\n", offset); + ret_val = -E1000_ERR_PARAM; + goto out; + } + + /* + * We'll need to use the SW defined pins to shift the write command + * out to the PHY. We first send a preamble to the PHY to signal the + * beginning of the MII instruction. This is done by sending 32 + * consecutive "1" bits. + */ + e1000_shift_out_mdi_bits_82543(hw, PHY_PREAMBLE, PHY_PREAMBLE_SIZE); + + /* + * Now combine the remaining required fields that will indicate a + * write operation. We use this method instead of calling the + * e1000_shift_out_mdi_bits routine for each field in the command. The + * format of a MII write instruction is as follows: + * . + */ + mdic = ((PHY_TURNAROUND) | (offset << 2) | (hw->phy.addr << 7) | + (PHY_OP_WRITE << 12) | (PHY_SOF << 14)); + mdic <<= 16; + mdic |= (u32) data; + + e1000_shift_out_mdi_bits_82543(hw, mdic, 32); + +out: + return ret_val; +} + +/** + * e1000_raise_mdi_clk_82543 - Raise Management Data Input clock + * @hw: pointer to the HW structure + * @ctrl: pointer to the control register + * + * Raise the management data input clock by setting the MDC bit in the control + * register. + **/ +static void e1000_raise_mdi_clk_82543(struct e1000_hw *hw, u32 *ctrl) +{ + /* + * Raise the clock input to the Management Data Clock (by setting the + * MDC bit), and then delay a sufficient amount of time. + */ + E1000_WRITE_REG(hw, E1000_CTRL, (*ctrl | E1000_CTRL_MDC)); + E1000_WRITE_FLUSH(hw); + usec_delay(10); +} + +/** + * e1000_lower_mdi_clk_82543 - Lower Management Data Input clock + * @hw: pointer to the HW structure + * @ctrl: pointer to the control register + * + * Lower the management data input clock by clearing the MDC bit in the + * control register. + **/ +static void e1000_lower_mdi_clk_82543(struct e1000_hw *hw, u32 *ctrl) +{ + /* + * Lower the clock input to the Management Data Clock (by clearing the + * MDC bit), and then delay a sufficient amount of time. + */ + E1000_WRITE_REG(hw, E1000_CTRL, (*ctrl & ~E1000_CTRL_MDC)); + E1000_WRITE_FLUSH(hw); + usec_delay(10); +} + +/** + * e1000_shift_out_mdi_bits_82543 - Shift data bits our to the PHY + * @hw: pointer to the HW structure + * @data: data to send to the PHY + * @count: number of bits to shift out + * + * We need to shift 'count' bits out to the PHY. So, the value in the + * "data" parameter will be shifted out to the PHY one bit at a time. + * In order to do this, "data" must be broken down into bits. + **/ +static void e1000_shift_out_mdi_bits_82543(struct e1000_hw *hw, u32 data, + u16 count) +{ + u32 ctrl, mask; + + /* + * We need to shift "count" number of bits out to the PHY. So, the + * value in the "data" parameter will be shifted out to the PHY one + * bit at a time. In order to do this, "data" must be broken down + * into bits. + */ + mask = 0x01; + mask <<= (count -1); + + ctrl = E1000_READ_REG(hw, E1000_CTRL); + + /* Set MDIO_DIR and MDC_DIR direction bits to be used as output pins. */ + ctrl |= (E1000_CTRL_MDIO_DIR | E1000_CTRL_MDC_DIR); + + while (mask) { + /* + * A "1" is shifted out to the PHY by setting the MDIO bit to + * "1" and then raising and lowering the Management Data Clock. + * A "0" is shifted out to the PHY by setting the MDIO bit to + * "0" and then raising and lowering the clock. + */ + if (data & mask) ctrl |= E1000_CTRL_MDIO; + else ctrl &= ~E1000_CTRL_MDIO; + + E1000_WRITE_REG(hw, E1000_CTRL, ctrl); + E1000_WRITE_FLUSH(hw); + + usec_delay(10); + + e1000_raise_mdi_clk_82543(hw, &ctrl); + e1000_lower_mdi_clk_82543(hw, &ctrl); + + mask >>= 1; + } +} + +/** + * e1000_shift_in_mdi_bits_82543 - Shift data bits in from the PHY + * @hw: pointer to the HW structure + * + * In order to read a register from the PHY, we need to shift 18 bits + * in from the PHY. Bits are "shifted in" by raising the clock input to + * the PHY (setting the MDC bit), and then reading the value of the data out + * MDIO bit. + **/ +static u16 e1000_shift_in_mdi_bits_82543(struct e1000_hw *hw) +{ + u32 ctrl; + u16 data = 0; + u8 i; + + /* + * In order to read a register from the PHY, we need to shift in a + * total of 18 bits from the PHY. The first two bit (turnaround) + * times are used to avoid contention on the MDIO pin when a read + * operation is performed. These two bits are ignored by us and + * thrown away. Bits are "shifted in" by raising the input to the + * Management Data Clock (setting the MDC bit) and then reading the + * value of the MDIO bit. + */ + ctrl = E1000_READ_REG(hw, E1000_CTRL); + + /* + * Clear MDIO_DIR (SWDPIO1) to indicate this bit is to be used as + * input. + */ + ctrl &= ~E1000_CTRL_MDIO_DIR; + ctrl &= ~E1000_CTRL_MDIO; + + E1000_WRITE_REG(hw, E1000_CTRL, ctrl); + E1000_WRITE_FLUSH(hw); + + /* + * Raise and lower the clock before reading in the data. This accounts + * for the turnaround bits. The first clock occurred when we clocked + * out the last bit of the Register Address. + */ + e1000_raise_mdi_clk_82543(hw, &ctrl); + e1000_lower_mdi_clk_82543(hw, &ctrl); + + for (data = 0, i = 0; i < 16; i++) { + data <<= 1; + e1000_raise_mdi_clk_82543(hw, &ctrl); + ctrl = E1000_READ_REG(hw, E1000_CTRL); + /* Check to see if we shifted in a "1". */ + if (ctrl & E1000_CTRL_MDIO) + data |= 1; + e1000_lower_mdi_clk_82543(hw, &ctrl); + } + + e1000_raise_mdi_clk_82543(hw, &ctrl); + e1000_lower_mdi_clk_82543(hw, &ctrl); + + return data; +} + +/** + * e1000_phy_force_speed_duplex_82543 - Force speed/duplex for PHY + * @hw: pointer to the HW structure + * + * Calls the function to force speed and duplex for the m88 PHY, and + * if the PHY is not auto-negotiating and the speed is forced to 10Mbit, + * then call the function for polarity reversal workaround. + **/ +static s32 e1000_phy_force_speed_duplex_82543(struct e1000_hw *hw) +{ + s32 ret_val; + + DEBUGFUNC("e1000_phy_force_speed_duplex_82543"); + + ret_val = e1000_phy_force_speed_duplex_m88(hw); + if (ret_val) + goto out; + + if (!hw->mac.autoneg && + (hw->mac.forced_speed_duplex & E1000_ALL_10_SPEED)) + ret_val = e1000_polarity_reversal_workaround_82543(hw); + +out: + return ret_val; +} + +/** + * e1000_polarity_reversal_workaround_82543 - Workaround polarity reversal + * @hw: pointer to the HW structure + * + * When forcing link to 10 Full or 10 Half, the PHY can reverse the polarity + * inadvertently. To workaround the issue, we disable the transmitter on + * the PHY until we have established the link partner's link parameters. + **/ +static s32 e1000_polarity_reversal_workaround_82543(struct e1000_hw *hw) +{ + s32 ret_val = E1000_SUCCESS; + u16 mii_status_reg; + u16 i; + bool link; + + if (!(hw->phy.ops.write_reg)) + goto out; + + /* Polarity reversal workaround for forced 10F/10H links. */ + + /* Disable the transmitter on the PHY */ + + ret_val = hw->phy.ops.write_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x0019); + if (ret_val) + goto out; + ret_val = hw->phy.ops.write_reg(hw, M88E1000_PHY_GEN_CONTROL, 0xFFFF); + if (ret_val) + goto out; + + ret_val = hw->phy.ops.write_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x0000); + if (ret_val) + goto out; + + /* + * This loop will early-out if the NO link condition has been met. + * In other words, DO NOT use e1000_phy_has_link_generic() here. + */ + for (i = PHY_FORCE_TIME; i > 0; i--) { + /* + * Read the MII Status Register and wait for Link Status bit + * to be clear. + */ + + ret_val = hw->phy.ops.read_reg(hw, PHY_STATUS, &mii_status_reg); + if (ret_val) + goto out; + + ret_val = hw->phy.ops.read_reg(hw, PHY_STATUS, &mii_status_reg); + if (ret_val) + goto out; + + if ((mii_status_reg & ~MII_SR_LINK_STATUS) == 0) + break; + msec_delay_irq(100); + } + + /* Recommended delay time after link has been lost */ + msec_delay_irq(1000); + + /* Now we will re-enable the transmitter on the PHY */ + + ret_val = hw->phy.ops.write_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x0019); + if (ret_val) + goto out; + msec_delay_irq(50); + ret_val = hw->phy.ops.write_reg(hw, M88E1000_PHY_GEN_CONTROL, 0xFFF0); + if (ret_val) + goto out; + msec_delay_irq(50); + ret_val = hw->phy.ops.write_reg(hw, M88E1000_PHY_GEN_CONTROL, 0xFF00); + if (ret_val) + goto out; + msec_delay_irq(50); + ret_val = hw->phy.ops.write_reg(hw, M88E1000_PHY_GEN_CONTROL, 0x0000); + if (ret_val) + goto out; + + ret_val = hw->phy.ops.write_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x0000); + if (ret_val) + goto out; + + /* + * Read the MII Status Register and wait for Link Status bit + * to be set. + */ + ret_val = e1000_phy_has_link_generic(hw, PHY_FORCE_TIME, 100000, &link); + if (ret_val) + goto out; + +out: + return ret_val; +} + +/** + * e1000_phy_hw_reset_82543 - PHY hardware reset + * @hw: pointer to the HW structure + * + * Sets the PHY_RESET_DIR bit in the extended device control register + * to put the PHY into a reset and waits for completion. Once the reset + * has been accomplished, clear the PHY_RESET_DIR bit to take the PHY out + * of reset. + **/ +static s32 e1000_phy_hw_reset_82543(struct e1000_hw *hw) +{ + u32 ctrl_ext; + s32 ret_val; + + DEBUGFUNC("e1000_phy_hw_reset_82543"); + + /* + * Read the Extended Device Control Register, assert the PHY_RESET_DIR + * bit to put the PHY into reset... + */ + ctrl_ext = E1000_READ_REG(hw, E1000_CTRL_EXT); + ctrl_ext |= E1000_CTRL_EXT_SDP4_DIR; + ctrl_ext &= ~E1000_CTRL_EXT_SDP4_DATA; + E1000_WRITE_REG(hw, E1000_CTRL_EXT, ctrl_ext); + E1000_WRITE_FLUSH(hw); + + msec_delay(10); + + /* ...then take it out of reset. */ + ctrl_ext |= E1000_CTRL_EXT_SDP4_DATA; + E1000_WRITE_REG(hw, E1000_CTRL_EXT, ctrl_ext); + E1000_WRITE_FLUSH(hw); + + usec_delay(150); + + if (!(hw->phy.ops.get_cfg_done)) + return E1000_SUCCESS; + + ret_val = hw->phy.ops.get_cfg_done(hw); + + return ret_val; +} + +/** + * e1000_reset_hw_82543 - Reset hardware + * @hw: pointer to the HW structure + * + * This resets the hardware into a known state. + **/ +static s32 e1000_reset_hw_82543(struct e1000_hw *hw) +{ + u32 ctrl, icr; + s32 ret_val = E1000_SUCCESS; + + DEBUGFUNC("e1000_reset_hw_82543"); + + DEBUGOUT("Masking off all interrupts\n"); + E1000_WRITE_REG(hw, E1000_IMC, 0xffffffff); + + E1000_WRITE_REG(hw, E1000_RCTL, 0); + E1000_WRITE_REG(hw, E1000_TCTL, E1000_TCTL_PSP); + E1000_WRITE_FLUSH(hw); + + e1000_set_tbi_sbp_82543(hw, FALSE); + + /* + * Delay to allow any outstanding PCI transactions to complete before + * resetting the device + */ + msec_delay(10); + + ctrl = E1000_READ_REG(hw, E1000_CTRL); + + DEBUGOUT("Issuing a global reset to 82543/82544 MAC\n"); + if (hw->mac.type == e1000_82543) { + E1000_WRITE_REG(hw, E1000_CTRL, ctrl | E1000_CTRL_RST); + } else { + /* + * The 82544 can't ACK the 64-bit write when issuing the + * reset, so use IO-mapping as a workaround. + */ + E1000_WRITE_REG_IO(hw, E1000_CTRL, ctrl | E1000_CTRL_RST); + } + + /* + * After MAC reset, force reload of NVM to restore power-on + * settings to device. + */ + hw->nvm.ops.reload(hw); + msec_delay(2); + + /* Masking off and clearing any pending interrupts */ + E1000_WRITE_REG(hw, E1000_IMC, 0xffffffff); + icr = E1000_READ_REG(hw, E1000_ICR); + + return ret_val; +} + +/** + * e1000_init_hw_82543 - Initialize hardware + * @hw: pointer to the HW structure + * + * This inits the hardware readying it for operation. + **/ +static s32 e1000_init_hw_82543(struct e1000_hw *hw) +{ + struct e1000_mac_info *mac = &hw->mac; + struct e1000_dev_spec_82543 *dev_spec = &hw->dev_spec._82543; + u32 ctrl; + s32 ret_val; + u16 i; + + DEBUGFUNC("e1000_init_hw_82543"); + + /* Disabling VLAN filtering */ + E1000_WRITE_REG(hw, E1000_VET, 0); + mac->ops.clear_vfta(hw); + + /* Setup the receive address. */ + e1000_init_rx_addrs_generic(hw, mac->rar_entry_count); + + /* Zero out the Multicast HASH table */ + DEBUGOUT("Zeroing the MTA\n"); + for (i = 0; i < mac->mta_reg_count; i++) { + E1000_WRITE_REG_ARRAY(hw, E1000_MTA, i, 0); + E1000_WRITE_FLUSH(hw); + } + + /* + * Set the PCI priority bit correctly in the CTRL register. This + * determines if the adapter gives priority to receives, or if it + * gives equal priority to transmits and receives. + */ + if (hw->mac.type == e1000_82543 && dev_spec->dma_fairness) { + ctrl = E1000_READ_REG(hw, E1000_CTRL); + E1000_WRITE_REG(hw, E1000_CTRL, ctrl | E1000_CTRL_PRIOR); + } + + e1000_pcix_mmrbc_workaround_generic(hw); + + /* Setup link and flow control */ + ret_val = mac->ops.setup_link(hw); + + /* + * Clear all of the statistics registers (clear on read). It is + * important that we do this after we have tried to establish link + * because the symbol error count will increment wildly if there + * is no link. + */ + e1000_clear_hw_cntrs_82543(hw); + + return ret_val; +} + +/** + * e1000_setup_link_82543 - Setup flow control and link settings + * @hw: pointer to the HW structure + * + * Read the EEPROM to determine the initial polarity value and write the + * extended device control register with the information before calling + * the generic setup link function, which does the following: + * Determines which flow control settings to use, then configures flow + * control. Calls the appropriate media-specific link configuration + * function. Assuming the adapter has a valid link partner, a valid link + * should be established. Assumes the hardware has previously been reset + * and the transmitter and receiver are not enabled. + **/ +static s32 e1000_setup_link_82543(struct e1000_hw *hw) +{ + u32 ctrl_ext; + s32 ret_val; + u16 data; + + DEBUGFUNC("e1000_setup_link_82543"); + + /* + * Take the 4 bits from NVM word 0xF that determine the initial + * polarity value for the SW controlled pins, and setup the + * Extended Device Control reg with that info. + * This is needed because one of the SW controlled pins is used for + * signal detection. So this should be done before phy setup. + */ + if (hw->mac.type == e1000_82543) { + ret_val = hw->nvm.ops.read(hw, NVM_INIT_CONTROL2_REG, 1, &data); + if (ret_val) { + DEBUGOUT("NVM Read Error\n"); + ret_val = -E1000_ERR_NVM; + goto out; + } + ctrl_ext = ((data & NVM_WORD0F_SWPDIO_EXT_MASK) << + NVM_SWDPIO_EXT_SHIFT); + E1000_WRITE_REG(hw, E1000_CTRL_EXT, ctrl_ext); + } + + ret_val = e1000_setup_link_generic(hw); + +out: + return ret_val; +} + +/** + * e1000_setup_copper_link_82543 - Configure copper link settings + * @hw: pointer to the HW structure + * + * Configures the link for auto-neg or forced speed and duplex. Then we check + * for link, once link is established calls to configure collision distance + * and flow control are called. + **/ +static s32 e1000_setup_copper_link_82543(struct e1000_hw *hw) +{ + u32 ctrl; + s32 ret_val; + bool link; + + DEBUGFUNC("e1000_setup_copper_link_82543"); + + ctrl = E1000_READ_REG(hw, E1000_CTRL) | E1000_CTRL_SLU; + /* + * With 82543, we need to force speed and duplex on the MAC + * equal to what the PHY speed and duplex configuration is. + * In addition, we need to perform a hardware reset on the + * PHY to take it out of reset. + */ + if (hw->mac.type == e1000_82543) { + ctrl |= (E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX); + E1000_WRITE_REG(hw, E1000_CTRL, ctrl); + ret_val = hw->phy.ops.reset(hw); + if (ret_val) + goto out; + hw->phy.reset_disable = FALSE; + } else { + ctrl &= ~(E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX); + E1000_WRITE_REG(hw, E1000_CTRL, ctrl); + } + + /* Set MDI/MDI-X, Polarity Reversal, and downshift settings */ + ret_val = e1000_copper_link_setup_m88(hw); + if (ret_val) + goto out; + + if (hw->mac.autoneg) { + /* + * Setup autoneg and flow control advertisement and perform + * autonegotiation. + */ + ret_val = e1000_copper_link_autoneg(hw); + if (ret_val) + goto out; + } else { + /* + * PHY will be set to 10H, 10F, 100H or 100F + * depending on user settings. + */ + DEBUGOUT("Forcing Speed and Duplex\n"); + ret_val = e1000_phy_force_speed_duplex_82543(hw); + if (ret_val) { + DEBUGOUT("Error Forcing Speed and Duplex\n"); + goto out; + } + } + + /* + * Check link status. Wait up to 100 microseconds for link to become + * valid. + */ + ret_val = e1000_phy_has_link_generic(hw, + COPPER_LINK_UP_LIMIT, + 10, + &link); + if (ret_val) + goto out; + + + if (link) { + DEBUGOUT("Valid link established!!!\n"); + /* Config the MAC and PHY after link is up */ + if (hw->mac.type == e1000_82544) { + e1000_config_collision_dist_generic(hw); + } else { + ret_val = e1000_config_mac_to_phy_82543(hw); + if (ret_val) + goto out; + } + ret_val = e1000_config_fc_after_link_up_generic(hw); + } else { + DEBUGOUT("Unable to establish link!!!\n"); + } + +out: + return ret_val; +} + +/** + * e1000_setup_fiber_link_82543 - Setup link for fiber + * @hw: pointer to the HW structure + * + * Configures collision distance and flow control for fiber links. Upon + * successful setup, poll for link. + **/ +static s32 e1000_setup_fiber_link_82543(struct e1000_hw *hw) +{ + u32 ctrl; + s32 ret_val; + + DEBUGFUNC("e1000_setup_fiber_link_82543"); + + ctrl = E1000_READ_REG(hw, E1000_CTRL); + + /* Take the link out of reset */ + ctrl &= ~E1000_CTRL_LRST; + + e1000_config_collision_dist_generic(hw); + + ret_val = e1000_commit_fc_settings_generic(hw); + if (ret_val) + goto out; + + DEBUGOUT("Auto-negotiation enabled\n"); + + E1000_WRITE_REG(hw, E1000_CTRL, ctrl); + E1000_WRITE_FLUSH(hw); + msec_delay(1); + + /* + * For these adapters, the SW definable pin 1 is cleared when the + * optics detect a signal. If we have a signal, then poll for a + * "Link-Up" indication. + */ + if (!(E1000_READ_REG(hw, E1000_CTRL) & E1000_CTRL_SWDPIN1)) { + ret_val = e1000_poll_fiber_serdes_link_generic(hw); + } else { + DEBUGOUT("No signal detected\n"); + } + +out: + return ret_val; +} + +/** + * e1000_check_for_copper_link_82543 - Check for link (Copper) + * @hw: pointer to the HW structure + * + * Checks the phy for link, if link exists, do the following: + * - check for downshift + * - do polarity workaround (if necessary) + * - configure collision distance + * - configure flow control after link up + * - configure tbi compatibility + **/ +static s32 e1000_check_for_copper_link_82543(struct e1000_hw *hw) +{ + struct e1000_mac_info *mac = &hw->mac; + u32 icr, rctl; + s32 ret_val; + u16 speed, duplex; + bool link; + + DEBUGFUNC("e1000_check_for_copper_link_82543"); + + if (!mac->get_link_status) { + ret_val = E1000_SUCCESS; + goto out; + } + + ret_val = e1000_phy_has_link_generic(hw, 1, 0, &link); + if (ret_val) + goto out; + + if (!link) + goto out; /* No link detected */ + + mac->get_link_status = FALSE; + + e1000_check_downshift_generic(hw); + + /* + * If we are forcing speed/duplex, then we can return since + * we have already determined whether we have link or not. + */ + if (!mac->autoneg) { + /* + * If speed and duplex are forced to 10H or 10F, then we will + * implement the polarity reversal workaround. We disable + * interrupts first, and upon returning, place the devices + * interrupt state to its previous value except for the link + * status change interrupt which will happened due to the + * execution of this workaround. + */ + if (mac->forced_speed_duplex & E1000_ALL_10_SPEED) { + E1000_WRITE_REG(hw, E1000_IMC, 0xFFFFFFFF); + ret_val = e1000_polarity_reversal_workaround_82543(hw); + icr = E1000_READ_REG(hw, E1000_ICR); + E1000_WRITE_REG(hw, E1000_ICS, (icr & ~E1000_ICS_LSC)); + E1000_WRITE_REG(hw, E1000_IMS, IMS_ENABLE_MASK); + } + + ret_val = -E1000_ERR_CONFIG; + goto out; + } + + /* + * We have a M88E1000 PHY and Auto-Neg is enabled. If we + * have Si on board that is 82544 or newer, Auto + * Speed Detection takes care of MAC speed/duplex + * configuration. So we only need to configure Collision + * Distance in the MAC. Otherwise, we need to force + * speed/duplex on the MAC to the current PHY speed/duplex + * settings. + */ + if (mac->type == e1000_82544) + e1000_config_collision_dist_generic(hw); + else { + ret_val = e1000_config_mac_to_phy_82543(hw); + if (ret_val) { + DEBUGOUT("Error configuring MAC to PHY settings\n"); + goto out; + } + } + + /* + * Configure Flow Control now that Auto-Neg has completed. + * First, we need to restore the desired flow control + * settings because we may have had to re-autoneg with a + * different link partner. + */ + ret_val = e1000_config_fc_after_link_up_generic(hw); + if (ret_val) { + DEBUGOUT("Error configuring flow control\n"); + } + + /* + * At this point we know that we are on copper and we have + * auto-negotiated link. These are conditions for checking the link + * partner capability register. We use the link speed to determine if + * TBI compatibility needs to be turned on or off. If the link is not + * at gigabit speed, then TBI compatibility is not needed. If we are + * at gigabit speed, we turn on TBI compatibility. + */ + if (e1000_tbi_compatibility_enabled_82543(hw)) { + ret_val = mac->ops.get_link_up_info(hw, &speed, &duplex); + if (ret_val) { + DEBUGOUT("Error getting link speed and duplex\n"); + return ret_val; + } + if (speed != SPEED_1000) { + /* + * If link speed is not set to gigabit speed, + * we do not need to enable TBI compatibility. + */ + if (e1000_tbi_sbp_enabled_82543(hw)) { + /* + * If we previously were in the mode, + * turn it off. + */ + e1000_set_tbi_sbp_82543(hw, FALSE); + rctl = E1000_READ_REG(hw, E1000_RCTL); + rctl &= ~E1000_RCTL_SBP; + E1000_WRITE_REG(hw, E1000_RCTL, rctl); + } + } else { + /* + * If TBI compatibility is was previously off, + * turn it on. For compatibility with a TBI link + * partner, we will store bad packets. Some + * frames have an additional byte on the end and + * will look like CRC errors to to the hardware. + */ + if (!e1000_tbi_sbp_enabled_82543(hw)) { + e1000_set_tbi_sbp_82543(hw, TRUE); + rctl = E1000_READ_REG(hw, E1000_RCTL); + rctl |= E1000_RCTL_SBP; + E1000_WRITE_REG(hw, E1000_RCTL, rctl); + } + } + } +out: + return ret_val; +} + +/** + * e1000_check_for_fiber_link_82543 - Check for link (Fiber) + * @hw: pointer to the HW structure + * + * Checks for link up on the hardware. If link is not up and we have + * a signal, then we need to force link up. + **/ +static s32 e1000_check_for_fiber_link_82543(struct e1000_hw *hw) +{ + struct e1000_mac_info *mac = &hw->mac; + u32 rxcw, ctrl, status; + s32 ret_val = E1000_SUCCESS; + + DEBUGFUNC("e1000_check_for_fiber_link_82543"); + + ctrl = E1000_READ_REG(hw, E1000_CTRL); + status = E1000_READ_REG(hw, E1000_STATUS); + rxcw = E1000_READ_REG(hw, E1000_RXCW); + + /* + * If we don't have link (auto-negotiation failed or link partner + * cannot auto-negotiate), the cable is plugged in (we have signal), + * and our link partner is not trying to auto-negotiate with us (we + * are receiving idles or data), we need to force link up. We also + * need to give auto-negotiation time to complete, in case the cable + * was just plugged in. The autoneg_failed flag does this. + */ + /* (ctrl & E1000_CTRL_SWDPIN1) == 0 == have signal */ + if ((!(ctrl & E1000_CTRL_SWDPIN1)) && + (!(status & E1000_STATUS_LU)) && + (!(rxcw & E1000_RXCW_C))) { + if (mac->autoneg_failed == 0) { + mac->autoneg_failed = 1; + ret_val = 0; + goto out; + } + DEBUGOUT("NOT RXing /C/, disable AutoNeg and force link.\n"); + + /* Disable auto-negotiation in the TXCW register */ + E1000_WRITE_REG(hw, E1000_TXCW, (mac->txcw & ~E1000_TXCW_ANE)); + + /* Force link-up and also force full-duplex. */ + ctrl = E1000_READ_REG(hw, E1000_CTRL); + ctrl |= (E1000_CTRL_SLU | E1000_CTRL_FD); + E1000_WRITE_REG(hw, E1000_CTRL, ctrl); + + /* Configure Flow Control after forcing link up. */ + ret_val = e1000_config_fc_after_link_up_generic(hw); + if (ret_val) { + DEBUGOUT("Error configuring flow control\n"); + goto out; + } + } else if ((ctrl & E1000_CTRL_SLU) && (rxcw & E1000_RXCW_C)) { + /* + * If we are forcing link and we are receiving /C/ ordered + * sets, re-enable auto-negotiation in the TXCW register + * and disable forced link in the Device Control register + * in an attempt to auto-negotiate with our link partner. + */ + DEBUGOUT("RXing /C/, enable AutoNeg and stop forcing link.\n"); + E1000_WRITE_REG(hw, E1000_TXCW, mac->txcw); + E1000_WRITE_REG(hw, E1000_CTRL, (ctrl & ~E1000_CTRL_SLU)); + + mac->serdes_has_link = TRUE; + } + +out: + return ret_val; +} + +/** + * e1000_config_mac_to_phy_82543 - Configure MAC to PHY settings + * @hw: pointer to the HW structure + * + * For the 82543 silicon, we need to set the MAC to match the settings + * of the PHY, even if the PHY is auto-negotiating. + **/ +static s32 e1000_config_mac_to_phy_82543(struct e1000_hw *hw) +{ + u32 ctrl; + s32 ret_val = E1000_SUCCESS; + u16 phy_data; + + DEBUGFUNC("e1000_config_mac_to_phy_82543"); + + if (!(hw->phy.ops.read_reg)) + goto out; + + /* Set the bits to force speed and duplex */ + ctrl = E1000_READ_REG(hw, E1000_CTRL); + ctrl |= (E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX); + ctrl &= ~(E1000_CTRL_SPD_SEL | E1000_CTRL_ILOS); + + /* + * Set up duplex in the Device Control and Transmit Control + * registers depending on negotiated values. + */ + ret_val = hw->phy.ops.read_reg(hw, M88E1000_PHY_SPEC_STATUS, &phy_data); + if (ret_val) + goto out; + + ctrl &= ~E1000_CTRL_FD; + if (phy_data & M88E1000_PSSR_DPLX) + ctrl |= E1000_CTRL_FD; + + e1000_config_collision_dist_generic(hw); + + /* + * Set up speed in the Device Control register depending on + * negotiated values. + */ + if ((phy_data & M88E1000_PSSR_SPEED) == M88E1000_PSSR_1000MBS) + ctrl |= E1000_CTRL_SPD_1000; + else if ((phy_data & M88E1000_PSSR_SPEED) == M88E1000_PSSR_100MBS) + ctrl |= E1000_CTRL_SPD_100; + + E1000_WRITE_REG(hw, E1000_CTRL, ctrl); + +out: + return ret_val; +} + +/** + * e1000_write_vfta_82543 - Write value to VLAN filter table + * @hw: pointer to the HW structure + * @offset: the 32-bit offset in which to write the value to. + * @value: the 32-bit value to write at location offset. + * + * This writes a 32-bit value to a 32-bit offset in the VLAN filter + * table. + **/ +static void e1000_write_vfta_82543(struct e1000_hw *hw, u32 offset, u32 value) +{ + u32 temp; + + DEBUGFUNC("e1000_write_vfta_82543"); + + if ((hw->mac.type == e1000_82544) && (offset & 1)) { + temp = E1000_READ_REG_ARRAY(hw, E1000_VFTA, offset - 1); + E1000_WRITE_REG_ARRAY(hw, E1000_VFTA, offset, value); + E1000_WRITE_FLUSH(hw); + E1000_WRITE_REG_ARRAY(hw, E1000_VFTA, offset - 1, temp); + E1000_WRITE_FLUSH(hw); + } else { + e1000_write_vfta_generic(hw, offset, value); + } +} + +/** + * e1000_mta_set_82543 - Set multicast filter table address + * @hw: pointer to the HW structure + * @hash_value: determines the MTA register and bit to set + * + * The multicast table address is a register array of 32-bit registers. + * The hash_value is used to determine what register the bit is in, the + * current value is read, the new bit is OR'd in and the new value is + * written back into the register. + **/ +static void e1000_mta_set_82543(struct e1000_hw *hw, u32 hash_value) +{ + u32 hash_bit, hash_reg, mta, temp; + + DEBUGFUNC("e1000_mta_set_82543"); + + hash_reg = (hash_value >> 5); + + /* + * If we are on an 82544 and we are trying to write an odd offset + * in the MTA, save off the previous entry before writing and + * restore the old value after writing. + */ + if ((hw->mac.type == e1000_82544) && (hash_reg & 1)) { + hash_reg &= (hw->mac.mta_reg_count - 1); + hash_bit = hash_value & 0x1F; + mta = E1000_READ_REG_ARRAY(hw, E1000_MTA, hash_reg); + mta |= (1 << hash_bit); + temp = E1000_READ_REG_ARRAY(hw, E1000_MTA, hash_reg - 1); + + E1000_WRITE_REG_ARRAY(hw, E1000_MTA, hash_reg, mta); + E1000_WRITE_FLUSH(hw); + E1000_WRITE_REG_ARRAY(hw, E1000_MTA, hash_reg - 1, temp); + E1000_WRITE_FLUSH(hw); + } else { + e1000_mta_set_generic(hw, hash_value); + } +} + +/** + * e1000_led_on_82543 - Turn on SW controllable LED + * @hw: pointer to the HW structure + * + * Turns the SW defined LED on. + **/ +static s32 e1000_led_on_82543(struct e1000_hw *hw) +{ + u32 ctrl = E1000_READ_REG(hw, E1000_CTRL); + + DEBUGFUNC("e1000_led_on_82543"); + + if (hw->mac.type == e1000_82544 && + hw->phy.media_type == e1000_media_type_copper) { + /* Clear SW-definable Pin 0 to turn on the LED */ + ctrl &= ~E1000_CTRL_SWDPIN0; + ctrl |= E1000_CTRL_SWDPIO0; + } else { + /* Fiber 82544 and all 82543 use this method */ + ctrl |= E1000_CTRL_SWDPIN0; + ctrl |= E1000_CTRL_SWDPIO0; + } + E1000_WRITE_REG(hw, E1000_CTRL, ctrl); + + return E1000_SUCCESS; +} + +/** + * e1000_led_off_82543 - Turn off SW controllable LED + * @hw: pointer to the HW structure + * + * Turns the SW defined LED off. + **/ +static s32 e1000_led_off_82543(struct e1000_hw *hw) +{ + u32 ctrl = E1000_READ_REG(hw, E1000_CTRL); + + DEBUGFUNC("e1000_led_off_82543"); + + if (hw->mac.type == e1000_82544 && + hw->phy.media_type == e1000_media_type_copper) { + /* Set SW-definable Pin 0 to turn off the LED */ + ctrl |= E1000_CTRL_SWDPIN0; + ctrl |= E1000_CTRL_SWDPIO0; + } else { + ctrl &= ~E1000_CTRL_SWDPIN0; + ctrl |= E1000_CTRL_SWDPIO0; + } + E1000_WRITE_REG(hw, E1000_CTRL, ctrl); + + return E1000_SUCCESS; +} + +/** + * e1000_clear_hw_cntrs_82543 - Clear device specific hardware counters + * @hw: pointer to the HW structure + * + * Clears the hardware counters by reading the counter registers. + **/ +static void e1000_clear_hw_cntrs_82543(struct e1000_hw *hw) +{ + DEBUGFUNC("e1000_clear_hw_cntrs_82543"); + + e1000_clear_hw_cntrs_base_generic(hw); + + E1000_READ_REG(hw, E1000_PRC64); + E1000_READ_REG(hw, E1000_PRC127); + E1000_READ_REG(hw, E1000_PRC255); + E1000_READ_REG(hw, E1000_PRC511); + E1000_READ_REG(hw, E1000_PRC1023); + E1000_READ_REG(hw, E1000_PRC1522); + E1000_READ_REG(hw, E1000_PTC64); + E1000_READ_REG(hw, E1000_PTC127); + E1000_READ_REG(hw, E1000_PTC255); + E1000_READ_REG(hw, E1000_PTC511); + E1000_READ_REG(hw, E1000_PTC1023); + E1000_READ_REG(hw, E1000_PTC1522); + + E1000_READ_REG(hw, E1000_ALGNERRC); + E1000_READ_REG(hw, E1000_RXERRC); + E1000_READ_REG(hw, E1000_TNCRS); + E1000_READ_REG(hw, E1000_CEXTERR); + E1000_READ_REG(hw, E1000_TSCTC); + E1000_READ_REG(hw, E1000_TSCTFC); +} diff --git a/sys/dev/netif/ig_hal/e1000_82543.h b/sys/dev/netif/ig_hal/e1000_82543.h new file mode 100644 index 0000000000..60e5c15dda --- /dev/null +++ b/sys/dev/netif/ig_hal/e1000_82543.h @@ -0,0 +1,57 @@ +/****************************************************************************** + + Copyright (c) 2001-2008, Intel Corporation + All rights reserved. + + Redistribution and use in source and binary forms, with or without + modification, are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, + this list of conditions and the following disclaimer. + + 2. Redistributions in binary form must reproduce the above copyright + notice, this list of conditions and the following disclaimer in the + documentation and/or other materials provided with the distribution. + + 3. Neither the name of the Intel Corporation nor the names of its + contributors may be used to endorse or promote products derived from + this software without specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE + ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE + LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR + CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF + SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS + INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN + CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) + ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + POSSIBILITY OF SUCH DAMAGE. + +******************************************************************************/ +/*$FreeBSD$*/ + +#ifndef _E1000_82543_H_ +#define _E1000_82543_H_ + +#define PHY_PREAMBLE 0xFFFFFFFF +#define PHY_PREAMBLE_SIZE 32 +#define PHY_SOF 0x1 +#define PHY_OP_READ 0x2 +#define PHY_OP_WRITE 0x1 +#define PHY_TURNAROUND 0x2 + +#define TBI_COMPAT_ENABLED 0x1 /* Global "knob" for the workaround */ +/* If TBI_COMPAT_ENABLED, then this is the current state (on/off) */ +#define TBI_SBP_ENABLED 0x2 + +void e1000_tbi_adjust_stats_82543(struct e1000_hw *hw, + struct e1000_hw_stats *stats, + u32 frame_len, u8 *mac_addr, + u32 max_frame_size); +void e1000_set_tbi_compatibility_82543(struct e1000_hw *hw, + bool state); +bool e1000_tbi_sbp_enabled_82543(struct e1000_hw *hw); + +#endif diff --git a/sys/dev/netif/ig_hal/e1000_82571.c b/sys/dev/netif/ig_hal/e1000_82571.c new file mode 100644 index 0000000000..db7852ab34 --- /dev/null +++ b/sys/dev/netif/ig_hal/e1000_82571.c @@ -0,0 +1,1521 @@ +/****************************************************************************** + + Copyright (c) 2001-2008, Intel Corporation + All rights reserved. + + Redistribution and use in source and binary forms, with or without + modification, are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, + this list of conditions and the following disclaimer. + + 2. Redistributions in binary form must reproduce the above copyright + notice, this list of conditions and the following disclaimer in the + documentation and/or other materials provided with the distribution. + + 3. Neither the name of the Intel Corporation nor the names of its + contributors may be used to endorse or promote products derived from + this software without specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE + ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE + LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR + CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF + SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS + INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN + CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) + ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + POSSIBILITY OF SUCH DAMAGE. + +******************************************************************************/ +/*$FreeBSD$*/ + +/* + * 82571EB Gigabit Ethernet Controller + * 82571EB Gigabit Ethernet Controller (Copper) + * 82571EB Gigabit Ethernet Controller (Fiber) + * 82571EB Dual Port Gigabit Mezzanine Adapter + * 82571EB Quad Port Gigabit Mezzanine Adapter + * 82571PT Gigabit PT Quad Port Server ExpressModule + * 82572EI Gigabit Ethernet Controller (Copper) + * 82572EI Gigabit Ethernet Controller (Fiber) + * 82572EI Gigabit Ethernet Controller + * 82573V Gigabit Ethernet Controller (Copper) + * 82573E Gigabit Ethernet Controller (Copper) + * 82573L Gigabit Ethernet Controller + * 82574L Gigabit Network Connection + */ + +#include "e1000_api.h" + +static s32 e1000_init_phy_params_82571(struct e1000_hw *hw); +static s32 e1000_init_nvm_params_82571(struct e1000_hw *hw); +static s32 e1000_init_mac_params_82571(struct e1000_hw *hw); +static s32 e1000_acquire_nvm_82571(struct e1000_hw *hw); +static void e1000_release_nvm_82571(struct e1000_hw *hw); +static s32 e1000_write_nvm_82571(struct e1000_hw *hw, u16 offset, + u16 words, u16 *data); +static s32 e1000_update_nvm_checksum_82571(struct e1000_hw *hw); +static s32 e1000_validate_nvm_checksum_82571(struct e1000_hw *hw); +static s32 e1000_get_cfg_done_82571(struct e1000_hw *hw); +static s32 e1000_set_d0_lplu_state_82571(struct e1000_hw *hw, + bool active); +static s32 e1000_reset_hw_82571(struct e1000_hw *hw); +static s32 e1000_init_hw_82571(struct e1000_hw *hw); +static void e1000_clear_vfta_82571(struct e1000_hw *hw); +static bool e1000_check_mng_mode_82574(struct e1000_hw *hw); +static s32 e1000_led_on_82574(struct e1000_hw *hw); +static void e1000_update_mc_addr_list_82571(struct e1000_hw *hw, + u8 *mc_addr_list, u32 mc_addr_count, + u32 rar_used_count, u32 rar_count); +static s32 e1000_setup_link_82571(struct e1000_hw *hw); +static s32 e1000_setup_copper_link_82571(struct e1000_hw *hw); +static s32 e1000_setup_fiber_serdes_link_82571(struct e1000_hw *hw); +static s32 e1000_valid_led_default_82571(struct e1000_hw *hw, u16 *data); +static void e1000_clear_hw_cntrs_82571(struct e1000_hw *hw); +static s32 e1000_get_hw_semaphore_82571(struct e1000_hw *hw); +static s32 e1000_fix_nvm_checksum_82571(struct e1000_hw *hw); +static s32 e1000_get_phy_id_82571(struct e1000_hw *hw); +static void e1000_put_hw_semaphore_82571(struct e1000_hw *hw); +static void e1000_initialize_hw_bits_82571(struct e1000_hw *hw); +static s32 e1000_write_nvm_eewr_82571(struct e1000_hw *hw, u16 offset, + u16 words, u16 *data); +static s32 e1000_read_mac_addr_82571(struct e1000_hw *hw); +static void e1000_power_down_phy_copper_82571(struct e1000_hw *hw); + +/** + * e1000_init_phy_params_82571 - Init PHY func ptrs. + * @hw: pointer to the HW structure + **/ +static s32 e1000_init_phy_params_82571(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val = E1000_SUCCESS; + + DEBUGFUNC("e1000_init_phy_params_82571"); + + if (hw->phy.media_type != e1000_media_type_copper) { + phy->type = e1000_phy_none; + goto out; + } + + phy->addr = 1; + phy->autoneg_mask = AUTONEG_ADVERTISE_SPEED_DEFAULT; + phy->reset_delay_us = 100; + + phy->ops.acquire = e1000_get_hw_semaphore_82571; + phy->ops.check_polarity = e1000_check_polarity_igp; + phy->ops.check_reset_block = e1000_check_reset_block_generic; + phy->ops.release = e1000_put_hw_semaphore_82571; + phy->ops.reset = e1000_phy_hw_reset_generic; + phy->ops.set_d0_lplu_state = e1000_set_d0_lplu_state_82571; + phy->ops.set_d3_lplu_state = e1000_set_d3_lplu_state_generic; + phy->ops.power_up = e1000_power_up_phy_copper; + phy->ops.power_down = e1000_power_down_phy_copper_82571; + + switch (hw->mac.type) { + case e1000_82571: + case e1000_82572: + phy->type = e1000_phy_igp_2; + phy->ops.get_cfg_done = e1000_get_cfg_done_82571; + phy->ops.get_info = e1000_get_phy_info_igp; + phy->ops.force_speed_duplex = e1000_phy_force_speed_duplex_igp; + phy->ops.get_cable_length = e1000_get_cable_length_igp_2; + phy->ops.read_reg = e1000_read_phy_reg_igp; + phy->ops.write_reg = e1000_write_phy_reg_igp; + + /* This uses above function pointers */ + ret_val = e1000_get_phy_id_82571(hw); + + /* Verify PHY ID */ + if (phy->id != IGP01E1000_I_PHY_ID) { + ret_val = -E1000_ERR_PHY; + goto out; + } + break; + case e1000_82573: + phy->type = e1000_phy_m88; + phy->ops.get_cfg_done = e1000_get_cfg_done_generic; + phy->ops.get_info = e1000_get_phy_info_m88; + phy->ops.commit = e1000_phy_sw_reset_generic; + phy->ops.force_speed_duplex = e1000_phy_force_speed_duplex_m88; + phy->ops.get_cable_length = e1000_get_cable_length_m88; + phy->ops.read_reg = e1000_read_phy_reg_m88; + phy->ops.write_reg = e1000_write_phy_reg_m88; + + /* This uses above function pointers */ + ret_val = e1000_get_phy_id_82571(hw); + + /* Verify PHY ID */ + if (phy->id != M88E1111_I_PHY_ID) { + ret_val = -E1000_ERR_PHY; + DEBUGOUT1("PHY ID unknown: type = 0x%08x\n", phy->id); + goto out; + } + break; + case e1000_82574: + phy->type = e1000_phy_bm; + phy->ops.get_cfg_done = e1000_get_cfg_done_generic; + phy->ops.get_info = e1000_get_phy_info_m88; + phy->ops.commit = e1000_phy_sw_reset_generic; + phy->ops.force_speed_duplex = e1000_phy_force_speed_duplex_m88; + phy->ops.get_cable_length = e1000_get_cable_length_m88; + phy->ops.read_reg = e1000_read_phy_reg_bm2; + phy->ops.write_reg = e1000_write_phy_reg_bm2; + + /* This uses above function pointers */ + ret_val = e1000_get_phy_id_82571(hw); + /* Verify PHY ID */ + if (phy->id != BME1000_E_PHY_ID_R2) { + ret_val = -E1000_ERR_PHY; + DEBUGOUT1("PHY ID unknown: type = 0x%08x\n", phy->id); + goto out; + } + break; + default: + ret_val = -E1000_ERR_PHY; + goto out; + break; + } + +out: + return ret_val; +} + +/** + * e1000_init_nvm_params_82571 - Init NVM func ptrs. + * @hw: pointer to the HW structure + **/ +static s32 e1000_init_nvm_params_82571(struct e1000_hw *hw) +{ + struct e1000_nvm_info *nvm = &hw->nvm; + u32 eecd = E1000_READ_REG(hw, E1000_EECD); + u16 size; + + DEBUGFUNC("e1000_init_nvm_params_82571"); + + nvm->opcode_bits = 8; + nvm->delay_usec = 1; + switch (nvm->override) { + case e1000_nvm_override_spi_large: + nvm->page_size = 32; + nvm->address_bits = 16; + break; + case e1000_nvm_override_spi_small: + nvm->page_size = 8; + nvm->address_bits = 8; + break; + default: + nvm->page_size = eecd & E1000_EECD_ADDR_BITS ? 32 : 8; + nvm->address_bits = eecd & E1000_EECD_ADDR_BITS ? 16 : 8; + break; + } + + switch (hw->mac.type) { + case e1000_82573: + case e1000_82574: + if (((eecd >> 15) & 0x3) == 0x3) { + nvm->type = e1000_nvm_flash_hw; + nvm->word_size = 2048; + /* + * Autonomous Flash update bit must be cleared due + * to Flash update issue. + */ + eecd &= ~E1000_EECD_AUPDEN; + E1000_WRITE_REG(hw, E1000_EECD, eecd); + break; + } + /* Fall Through */ + default: + nvm->type = e1000_nvm_eeprom_spi; + size = (u16)((eecd & E1000_EECD_SIZE_EX_MASK) >> + E1000_EECD_SIZE_EX_SHIFT); + /* + * Added to a constant, "size" becomes the left-shift value + * for setting word_size. + */ + size += NVM_WORD_SIZE_BASE_SHIFT; + + /* EEPROM access above 16k is unsupported */ + if (size > 14) + size = 14; + nvm->word_size = 1 << size; + break; + } + + /* Function Pointers */ + nvm->ops.acquire = e1000_acquire_nvm_82571; + nvm->ops.read = e1000_read_nvm_eerd; + nvm->ops.release = e1000_release_nvm_82571; + nvm->ops.update = e1000_update_nvm_checksum_82571; + nvm->ops.validate = e1000_validate_nvm_checksum_82571; + nvm->ops.valid_led_default = e1000_valid_led_default_82571; + nvm->ops.write = e1000_write_nvm_82571; + + return E1000_SUCCESS; +} + +/** + * e1000_init_mac_params_82571 - Init MAC func ptrs. + * @hw: pointer to the HW structure + **/ +static s32 e1000_init_mac_params_82571(struct e1000_hw *hw) +{ + struct e1000_mac_info *mac = &hw->mac; + s32 ret_val = E1000_SUCCESS; + + DEBUGFUNC("e1000_init_mac_params_82571"); + + /* Set media type */ + switch (hw->device_id) { + case E1000_DEV_ID_82571EB_FIBER: + case E1000_DEV_ID_82572EI_FIBER: + case E1000_DEV_ID_82571EB_QUAD_FIBER: + hw->phy.media_type = e1000_media_type_fiber; + break; + case E1000_DEV_ID_82571EB_SERDES: + case E1000_DEV_ID_82571EB_SERDES_DUAL: + case E1000_DEV_ID_82571EB_SERDES_QUAD: + case E1000_DEV_ID_82572EI_SERDES: + hw->phy.media_type = e1000_media_type_internal_serdes; + break; + default: + hw->phy.media_type = e1000_media_type_copper; + break; + } + + /* Set mta register count */ + mac->mta_reg_count = 128; + /* Set rar entry count */ + mac->rar_entry_count = E1000_RAR_ENTRIES; + /* Set if part includes ASF firmware */ + mac->asf_firmware_present = TRUE; + /* Set if manageability features are enabled. */ + mac->arc_subsystem_valid = + (E1000_READ_REG(hw, E1000_FWSM) & E1000_FWSM_MODE_MASK) + ? TRUE : FALSE; + + /* Function pointers */ + + /* bus type/speed/width */ + mac->ops.get_bus_info = e1000_get_bus_info_pcie_generic; + /* function id */ + switch (hw->mac.type) { + case e1000_82573: + case e1000_82574: + mac->ops.set_lan_id = e1000_set_lan_id_single_port; + break; + default: + break; + } + /* reset */ + mac->ops.reset_hw = e1000_reset_hw_82571; + /* hw initialization */ + mac->ops.init_hw = e1000_init_hw_82571; + /* link setup */ + mac->ops.setup_link = e1000_setup_link_82571; + /* physical interface link setup */ + mac->ops.setup_physical_interface = + (hw->phy.media_type == e1000_media_type_copper) + ? e1000_setup_copper_link_82571 + : e1000_setup_fiber_serdes_link_82571; + /* check for link */ + switch (hw->phy.media_type) { + case e1000_media_type_copper: + mac->ops.check_for_link = e1000_check_for_copper_link_generic; + break; + case e1000_media_type_fiber: + mac->ops.check_for_link = e1000_check_for_fiber_link_generic; + break; + case e1000_media_type_internal_serdes: + mac->ops.check_for_link = e1000_check_for_serdes_link_generic; + break; + default: + ret_val = -E1000_ERR_CONFIG; + goto out; + break; + } + /* check management mode */ + switch (hw->mac.type) { + case e1000_82574: + mac->ops.check_mng_mode = e1000_check_mng_mode_82574; + break; + default: + mac->ops.check_mng_mode = e1000_check_mng_mode_generic; + break; + } + /* multicast address update */ + mac->ops.update_mc_addr_list = e1000_update_mc_addr_list_82571; + /* writing VFTA */ + mac->ops.write_vfta = e1000_write_vfta_generic; + /* clearing VFTA */ + mac->ops.clear_vfta = e1000_clear_vfta_82571; + /* setting MTA */ + mac->ops.mta_set = e1000_mta_set_generic; + /* read mac address */ + mac->ops.read_mac_addr = e1000_read_mac_addr_82571; + /* blink LED */ + mac->ops.blink_led = e1000_blink_led_generic; + /* setup LED */ + mac->ops.setup_led = e1000_setup_led_generic; + /* cleanup LED */ + mac->ops.cleanup_led = e1000_cleanup_led_generic; + /* turn on/off LED */ + switch (hw->mac.type) { + case e1000_82574: + mac->ops.led_on = e1000_led_on_82574; + break; + default: + mac->ops.led_on = e1000_led_on_generic; + break; + } + mac->ops.led_off = e1000_led_off_generic; + /* clear hardware counters */ + mac->ops.clear_hw_cntrs = e1000_clear_hw_cntrs_82571; + /* link info */ + mac->ops.get_link_up_info = + (hw->phy.media_type == e1000_media_type_copper) + ? e1000_get_speed_and_duplex_copper_generic + : e1000_get_speed_and_duplex_fiber_serdes_generic; + +out: + return ret_val; +} + +/** + * e1000_init_function_pointers_82571 - Init func ptrs. + * @hw: pointer to the HW structure + * + * Called to initialize all function pointers and parameters. + **/ +void e1000_init_function_pointers_82571(struct e1000_hw *hw) +{ + DEBUGFUNC("e1000_init_function_pointers_82571"); + + hw->mac.ops.init_params = e1000_init_mac_params_82571; + hw->nvm.ops.init_params = e1000_init_nvm_params_82571; + hw->phy.ops.init_params = e1000_init_phy_params_82571; +} + +/** + * e1000_get_phy_id_82571 - Retrieve the PHY ID and revision + * @hw: pointer to the HW structure + * + * Reads the PHY registers and stores the PHY ID and possibly the PHY + * revision in the hardware structure. + **/ +static s32 e1000_get_phy_id_82571(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val = E1000_SUCCESS; + u16 phy_id = 0; + + DEBUGFUNC("e1000_get_phy_id_82571"); + + switch (hw->mac.type) { + case e1000_82571: + case e1000_82572: + /* + * The 82571 firmware may still be configuring the PHY. + * In this case, we cannot access the PHY until the + * configuration is done. So we explicitly set the + * PHY ID. + */ + phy->id = IGP01E1000_I_PHY_ID; + break; + case e1000_82573: + ret_val = e1000_get_phy_id(hw); + break; + case e1000_82574: + ret_val = phy->ops.read_reg(hw, PHY_ID1, &phy_id); + if (ret_val) + goto out; + + phy->id = (u32)(phy_id << 16); + usec_delay(20); + ret_val = phy->ops.read_reg(hw, PHY_ID2, &phy_id); + if (ret_val) + goto out; + + phy->id |= (u32)(phy_id); + phy->revision = (u32)(phy_id & ~PHY_REVISION_MASK); + break; + default: + ret_val = -E1000_ERR_PHY; + break; + } + +out: + return ret_val; +} + +/** + * e1000_get_hw_semaphore_82571 - Acquire hardware semaphore + * @hw: pointer to the HW structure + * + * Acquire the HW semaphore to access the PHY or NVM + **/ +static s32 e1000_get_hw_semaphore_82571(struct e1000_hw *hw) +{ + u32 swsm; + s32 ret_val = E1000_SUCCESS; + s32 timeout = hw->nvm.word_size + 1; + s32 i = 0; + + DEBUGFUNC("e1000_get_hw_semaphore_82571"); + + /* Get the FW semaphore. */ + for (i = 0; i < timeout; i++) { + swsm = E1000_READ_REG(hw, E1000_SWSM); + E1000_WRITE_REG(hw, E1000_SWSM, swsm | E1000_SWSM_SWESMBI); + + /* Semaphore acquired if bit latched */ + if (E1000_READ_REG(hw, E1000_SWSM) & E1000_SWSM_SWESMBI) + break; + + usec_delay(50); + } + + if (i == timeout) { + /* Release semaphores */ + e1000_put_hw_semaphore_generic(hw); + DEBUGOUT("Driver can't access the NVM\n"); + ret_val = -E1000_ERR_NVM; + goto out; + } + +out: + return ret_val; +} + +/** + * e1000_put_hw_semaphore_82571 - Release hardware semaphore + * @hw: pointer to the HW structure + * + * Release hardware semaphore used to access the PHY or NVM + **/ +static void e1000_put_hw_semaphore_82571(struct e1000_hw *hw) +{ + u32 swsm; + + DEBUGFUNC("e1000_put_hw_semaphore_82571"); + + swsm = E1000_READ_REG(hw, E1000_SWSM); + + swsm &= ~E1000_SWSM_SWESMBI; + + E1000_WRITE_REG(hw, E1000_SWSM, swsm); +} + +/** + * e1000_acquire_nvm_82571 - Request for access to the EEPROM + * @hw: pointer to the HW structure + * + * To gain access to the EEPROM, first we must obtain a hardware semaphore. + * Then for non-82573 hardware, set the EEPROM access request bit and wait + * for EEPROM access grant bit. If the access grant bit is not set, release + * hardware semaphore. + **/ +static s32 e1000_acquire_nvm_82571(struct e1000_hw *hw) +{ + s32 ret_val; + + DEBUGFUNC("e1000_acquire_nvm_82571"); + + ret_val = e1000_get_hw_semaphore_82571(hw); + if (ret_val) + goto out; + + if (hw->mac.type != e1000_82573 && hw->mac.type != e1000_82574) + ret_val = e1000_acquire_nvm_generic(hw); + + if (ret_val) + e1000_put_hw_semaphore_82571(hw); + +out: + return ret_val; +} + +/** + * e1000_release_nvm_82571 - Release exclusive access to EEPROM + * @hw: pointer to the HW structure + * + * Stop any current commands to the EEPROM and clear the EEPROM request bit. + **/ +static void e1000_release_nvm_82571(struct e1000_hw *hw) +{ + DEBUGFUNC("e1000_release_nvm_82571"); + + e1000_release_nvm_generic(hw); + e1000_put_hw_semaphore_82571(hw); +} + +/** + * e1000_write_nvm_82571 - Write to EEPROM using appropriate interface + * @hw: pointer to the HW structure + * @offset: offset within the EEPROM to be written to + * @words: number of words to write + * @data: 16 bit word(s) to be written to the EEPROM + * + * For non-82573 silicon, write data to EEPROM at offset using SPI interface. + * + * If e1000_update_nvm_checksum is not called after this function, the + * EEPROM will most likely contain an invalid checksum. + **/ +static s32 e1000_write_nvm_82571(struct e1000_hw *hw, u16 offset, u16 words, + u16 *data) +{ + s32 ret_val = E1000_SUCCESS; + + DEBUGFUNC("e1000_write_nvm_82571"); + + switch (hw->mac.type) { + case e1000_82573: + case e1000_82574: + ret_val = e1000_write_nvm_eewr_82571(hw, offset, words, data); + break; + case e1000_82571: + case e1000_82572: + ret_val = e1000_write_nvm_spi(hw, offset, words, data); + break; + default: + ret_val = -E1000_ERR_NVM; + break; + } + + return ret_val; +} + +/** + * e1000_update_nvm_checksum_82571 - Update EEPROM checksum + * @hw: pointer to the HW structure + * + * Updates the EEPROM checksum by reading/adding each word of the EEPROM + * up to the checksum. Then calculates the EEPROM checksum and writes the + * value to the EEPROM. + **/ +static s32 e1000_update_nvm_checksum_82571(struct e1000_hw *hw) +{ + u32 eecd; + s32 ret_val; + u16 i; + + DEBUGFUNC("e1000_update_nvm_checksum_82571"); + + ret_val = e1000_update_nvm_checksum_generic(hw); + if (ret_val) + goto out; + + /* + * If our nvm is an EEPROM, then we're done + * otherwise, commit the checksum to the flash NVM. + */ + if (hw->nvm.type != e1000_nvm_flash_hw) + goto out; + + /* Check for pending operations. */ + for (i = 0; i < E1000_FLASH_UPDATES; i++) { + msec_delay(1); + if ((E1000_READ_REG(hw, E1000_EECD) & E1000_EECD_FLUPD) == 0) + break; + } + + if (i == E1000_FLASH_UPDATES) { + ret_val = -E1000_ERR_NVM; + goto out; + } + + /* Reset the firmware if using STM opcode. */ + if ((E1000_READ_REG(hw, E1000_FLOP) & 0xFF00) == E1000_STM_OPCODE) { + /* + * The enabling of and the actual reset must be done + * in two write cycles. + */ + E1000_WRITE_REG(hw, E1000_HICR, E1000_HICR_FW_RESET_ENABLE); + E1000_WRITE_FLUSH(hw); + E1000_WRITE_REG(hw, E1000_HICR, E1000_HICR_FW_RESET); + } + + /* Commit the write to flash */ + eecd = E1000_READ_REG(hw, E1000_EECD) | E1000_EECD_FLUPD; + E1000_WRITE_REG(hw, E1000_EECD, eecd); + + for (i = 0; i < E1000_FLASH_UPDATES; i++) { + msec_delay(1); + if ((E1000_READ_REG(hw, E1000_EECD) & E1000_EECD_FLUPD) == 0) + break; + } + + if (i == E1000_FLASH_UPDATES) { + ret_val = -E1000_ERR_NVM; + goto out; + } + +out: + return ret_val; +} + +/** + * e1000_validate_nvm_checksum_82571 - Validate EEPROM checksum + * @hw: pointer to the HW structure + * + * Calculates the EEPROM checksum by reading/adding each word of the EEPROM + * and then verifies that the sum of the EEPROM is equal to 0xBABA. + **/ +static s32 e1000_validate_nvm_checksum_82571(struct e1000_hw *hw) +{ + DEBUGFUNC("e1000_validate_nvm_checksum_82571"); + + if (hw->nvm.type == e1000_nvm_flash_hw) + e1000_fix_nvm_checksum_82571(hw); + + return e1000_validate_nvm_checksum_generic(hw); +} + +/** + * e1000_write_nvm_eewr_82571 - Write to EEPROM for 82573 silicon + * @hw: pointer to the HW structure + * @offset: offset within the EEPROM to be written to + * @words: number of words to write + * @data: 16 bit word(s) to be written to the EEPROM + * + * After checking for invalid values, poll the EEPROM to ensure the previous + * command has completed before trying to write the next word. After write + * poll for completion. + * + * If e1000_update_nvm_checksum is not called after this function, the + * EEPROM will most likely contain an invalid checksum. + **/ +static s32 e1000_write_nvm_eewr_82571(struct e1000_hw *hw, u16 offset, + u16 words, u16 *data) +{ + struct e1000_nvm_info *nvm = &hw->nvm; + u32 i, eewr = 0; + s32 ret_val = 0; + + DEBUGFUNC("e1000_write_nvm_eewr_82571"); + + /* + * A check for invalid values: offset too large, too many words, + * and not enough words. + */ + if ((offset >= nvm->word_size) || (words > (nvm->word_size - offset)) || + (words == 0)) { + DEBUGOUT("nvm parameter(s) out of bounds\n"); + ret_val = -E1000_ERR_NVM; + goto out; + } + + for (i = 0; i < words; i++) { + eewr = (data[i] << E1000_NVM_RW_REG_DATA) | + ((offset+i) << E1000_NVM_RW_ADDR_SHIFT) | + E1000_NVM_RW_REG_START; + + ret_val = e1000_poll_eerd_eewr_done(hw, E1000_NVM_POLL_WRITE); + if (ret_val) + break; + + E1000_WRITE_REG(hw, E1000_EEWR, eewr); + + ret_val = e1000_poll_eerd_eewr_done(hw, E1000_NVM_POLL_WRITE); + if (ret_val) + break; + } + +out: + return ret_val; +} + +/** + * e1000_get_cfg_done_82571 - Poll for configuration done + * @hw: pointer to the HW structure + * + * Reads the management control register for the config done bit to be set. + **/ +static s32 e1000_get_cfg_done_82571(struct e1000_hw *hw) +{ + s32 timeout = PHY_CFG_TIMEOUT; + s32 ret_val = E1000_SUCCESS; + + DEBUGFUNC("e1000_get_cfg_done_82571"); + + while (timeout) { + if (E1000_READ_REG(hw, E1000_EEMNGCTL) & E1000_NVM_CFG_DONE_PORT_0) + break; + msec_delay(1); + timeout--; + } + if (!timeout) { + DEBUGOUT("MNG configuration cycle has not completed.\n"); + ret_val = -E1000_ERR_RESET; + goto out; + } + +out: + return ret_val; +} + +/** + * e1000_set_d0_lplu_state_82571 - Set Low Power Linkup D0 state + * @hw: pointer to the HW structure + * @active: TRUE to enable LPLU, FALSE to disable + * + * Sets the LPLU D0 state according to the active flag. When activating LPLU + * this function also disables smart speed and vice versa. LPLU will not be + * activated unless the device autonegotiation advertisement meets standards + * of either 10 or 10/100 or 10/100/1000 at all duplexes. This is a function + * pointer entry point only called by PHY setup routines. + **/ +static s32 e1000_set_d0_lplu_state_82571(struct e1000_hw *hw, bool active) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val = E1000_SUCCESS; + u16 data; + + DEBUGFUNC("e1000_set_d0_lplu_state_82571"); + + if (!(phy->ops.read_reg)) + goto out; + + ret_val = phy->ops.read_reg(hw, IGP02E1000_PHY_POWER_MGMT, &data); + if (ret_val) + goto out; + + if (active) { + data |= IGP02E1000_PM_D0_LPLU; + ret_val = phy->ops.write_reg(hw, IGP02E1000_PHY_POWER_MGMT, + data); + if (ret_val) + goto out; + + /* When LPLU is enabled, we should disable SmartSpeed */ + ret_val = phy->ops.read_reg(hw, IGP01E1000_PHY_PORT_CONFIG, + &data); + data &= ~IGP01E1000_PSCFR_SMART_SPEED; + ret_val = phy->ops.write_reg(hw, IGP01E1000_PHY_PORT_CONFIG, + data); + if (ret_val) + goto out; + } else { + data &= ~IGP02E1000_PM_D0_LPLU; + ret_val = phy->ops.write_reg(hw, IGP02E1000_PHY_POWER_MGMT, + data); + /* + * LPLU and SmartSpeed are mutually exclusive. LPLU is used + * during Dx states where the power conservation is most + * important. During driver activity we should enable + * SmartSpeed, so performance is maintained. + */ + if (phy->smart_speed == e1000_smart_speed_on) { + ret_val = phy->ops.read_reg(hw, + IGP01E1000_PHY_PORT_CONFIG, + &data); + if (ret_val) + goto out; + + data |= IGP01E1000_PSCFR_SMART_SPEED; + ret_val = phy->ops.write_reg(hw, + IGP01E1000_PHY_PORT_CONFIG, + data); + if (ret_val) + goto out; + } else if (phy->smart_speed == e1000_smart_speed_off) { + ret_val = phy->ops.read_reg(hw, + IGP01E1000_PHY_PORT_CONFIG, + &data); + if (ret_val) + goto out; + + data &= ~IGP01E1000_PSCFR_SMART_SPEED; + ret_val = phy->ops.write_reg(hw, + IGP01E1000_PHY_PORT_CONFIG, + data); + if (ret_val) + goto out; + } + } + +out: + return ret_val; +} + +/** + * e1000_reset_hw_82571 - Reset hardware + * @hw: pointer to the HW structure + * + * This resets the hardware into a known state. + **/ +static s32 e1000_reset_hw_82571(struct e1000_hw *hw) +{ + u32 ctrl, extcnf_ctrl, ctrl_ext, icr; + s32 ret_val; + u16 i = 0; + + DEBUGFUNC("e1000_reset_hw_82571"); + + /* + * Prevent the PCI-E bus from sticking if there is no TLP connection + * on the last TLP read/write transaction when MAC is reset. + */ + ret_val = e1000_disable_pcie_master_generic(hw); + if (ret_val) + DEBUGOUT("PCI-E Master disable polling has failed.\n"); + + DEBUGOUT("Masking off all interrupts\n"); + E1000_WRITE_REG(hw, E1000_IMC, 0xffffffff); + + E1000_WRITE_REG(hw, E1000_RCTL, 0); + E1000_WRITE_REG(hw, E1000_TCTL, E1000_TCTL_PSP); + E1000_WRITE_FLUSH(hw); + + msec_delay(10); + + /* + * Must acquire the MDIO ownership before MAC reset. + * Ownership defaults to firmware after a reset. + */ + if (hw->mac.type == e1000_82573 || hw->mac.type == e1000_82574) { + extcnf_ctrl = E1000_READ_REG(hw, E1000_EXTCNF_CTRL); + extcnf_ctrl |= E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP; + + do { + E1000_WRITE_REG(hw, E1000_EXTCNF_CTRL, extcnf_ctrl); + extcnf_ctrl = E1000_READ_REG(hw, E1000_EXTCNF_CTRL); + + if (extcnf_ctrl & E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP) + break; + + extcnf_ctrl |= E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP; + + msec_delay(2); + i++; + } while (i < MDIO_OWNERSHIP_TIMEOUT); + } + + ctrl = E1000_READ_REG(hw, E1000_CTRL); + + DEBUGOUT("Issuing a global reset to MAC\n"); + E1000_WRITE_REG(hw, E1000_CTRL, ctrl | E1000_CTRL_RST); + + if (hw->nvm.type == e1000_nvm_flash_hw) { + usec_delay(10); + ctrl_ext = E1000_READ_REG(hw, E1000_CTRL_EXT); + ctrl_ext |= E1000_CTRL_EXT_EE_RST; + E1000_WRITE_REG(hw, E1000_CTRL_EXT, ctrl_ext); + E1000_WRITE_FLUSH(hw); + } + + ret_val = e1000_get_auto_rd_done_generic(hw); + if (ret_val) + /* We don't want to continue accessing MAC registers. */ + goto out; + + /* + * Phy configuration from NVM just starts after EECD_AUTO_RD is set. + * Need to wait for Phy configuration completion before accessing + * NVM and Phy. + */ + if (hw->mac.type == e1000_82573 || hw->mac.type == e1000_82574) + msec_delay(25); + + /* Clear any pending interrupt events. */ + E1000_WRITE_REG(hw, E1000_IMC, 0xffffffff); + icr = E1000_READ_REG(hw, E1000_ICR); + + if (!(e1000_check_alt_mac_addr_generic(hw))) + e1000_set_laa_state_82571(hw, TRUE); + +out: + return ret_val; +} + +/** + * e1000_init_hw_82571 - Initialize hardware + * @hw: pointer to the HW structure + * + * This inits the hardware readying it for operation. + **/ +static s32 e1000_init_hw_82571(struct e1000_hw *hw) +{ + struct e1000_mac_info *mac = &hw->mac; + u32 reg_data; + s32 ret_val; + u16 i, rar_count = mac->rar_entry_count; + + DEBUGFUNC("e1000_init_hw_82571"); + + e1000_initialize_hw_bits_82571(hw); + + /* Initialize identification LED */ + ret_val = e1000_id_led_init_generic(hw); + if (ret_val) { + DEBUGOUT("Error initializing identification LED\n"); + /* This is not fatal and we should not stop init due to this */ + } + + /* Disabling VLAN filtering */ + DEBUGOUT("Initializing the IEEE VLAN\n"); + mac->ops.clear_vfta(hw); + + /* Setup the receive address. */ + /* + * If, however, a locally administered address was assigned to the + * 82571, we must reserve a RAR for it to work around an issue where + * resetting one port will reload the MAC on the other port. + */ + if (e1000_get_laa_state_82571(hw)) + rar_count--; + e1000_init_rx_addrs_generic(hw, rar_count); + + /* Zero out the Multicast HASH table */ + DEBUGOUT("Zeroing the MTA\n"); + for (i = 0; i < mac->mta_reg_count; i++) + E1000_WRITE_REG_ARRAY(hw, E1000_MTA, i, 0); + + /* Setup link and flow control */ + ret_val = mac->ops.setup_link(hw); + + /* Set the transmit descriptor write-back policy */ + reg_data = E1000_READ_REG(hw, E1000_TXDCTL(0)); + reg_data = (reg_data & ~E1000_TXDCTL_WTHRESH) | + E1000_TXDCTL_FULL_TX_DESC_WB | + E1000_TXDCTL_COUNT_DESC; + E1000_WRITE_REG(hw, E1000_TXDCTL(0), reg_data); + + /* ...for both queues. */ + if (mac->type != e1000_82573 && mac->type != e1000_82574) { + reg_data = E1000_READ_REG(hw, E1000_TXDCTL(1)); + reg_data = (reg_data & ~E1000_TXDCTL_WTHRESH) | + E1000_TXDCTL_FULL_TX_DESC_WB | + E1000_TXDCTL_COUNT_DESC; + E1000_WRITE_REG(hw, E1000_TXDCTL(1), reg_data); + } else { + e1000_enable_tx_pkt_filtering_generic(hw); + reg_data = E1000_READ_REG(hw, E1000_GCR); + reg_data |= E1000_GCR_L1_ACT_WITHOUT_L0S_RX; + E1000_WRITE_REG(hw, E1000_GCR, reg_data); + } + + /* + * Clear all of the statistics registers (clear on read). It is + * important that we do this after we have tried to establish link + * because the symbol error count will increment wildly if there + * is no link. + */ + e1000_clear_hw_cntrs_82571(hw); + + return ret_val; +} + +/** + * e1000_initialize_hw_bits_82571 - Initialize hardware-dependent bits + * @hw: pointer to the HW structure + * + * Initializes required hardware-dependent bits needed for normal operation. + **/ +static void e1000_initialize_hw_bits_82571(struct e1000_hw *hw) +{ + u32 reg; + + DEBUGFUNC("e1000_initialize_hw_bits_82571"); + + /* Transmit Descriptor Control 0 */ + reg = E1000_READ_REG(hw, E1000_TXDCTL(0)); + reg |= (1 << 22); + E1000_WRITE_REG(hw, E1000_TXDCTL(0), reg); + + /* Transmit Descriptor Control 1 */ + reg = E1000_READ_REG(hw, E1000_TXDCTL(1)); + reg |= (1 << 22); + E1000_WRITE_REG(hw, E1000_TXDCTL(1), reg); + + /* Transmit Arbitration Control 0 */ + reg = E1000_READ_REG(hw, E1000_TARC(0)); + reg &= ~(0xF << 27); /* 30:27 */ + switch (hw->mac.type) { + case e1000_82571: + case e1000_82572: + reg |= (1 << 23) | (1 << 24) | (1 << 25) | (1 << 26); + break; + default: + break; + } + E1000_WRITE_REG(hw, E1000_TARC(0), reg); + + /* Transmit Arbitration Control 1 */ + reg = E1000_READ_REG(hw, E1000_TARC(1)); + switch (hw->mac.type) { + case e1000_82571: + case e1000_82572: + reg &= ~((1 << 29) | (1 << 30)); + reg |= (1 << 22) | (1 << 24) | (1 << 25) | (1 << 26); + if (E1000_READ_REG(hw, E1000_TCTL) & E1000_TCTL_MULR) + reg &= ~(1 << 28); + else + reg |= (1 << 28); + E1000_WRITE_REG(hw, E1000_TARC(1), reg); + break; + default: + break; + } + + /* Device Control */ + if (hw->mac.type == e1000_82573 || hw->mac.type == e1000_82574) { + reg = E1000_READ_REG(hw, E1000_CTRL); + reg &= ~(1 << 29); + E1000_WRITE_REG(hw, E1000_CTRL, reg); + } + + /* Extended Device Control */ + if (hw->mac.type == e1000_82573 || hw->mac.type == e1000_82574) { + reg = E1000_READ_REG(hw, E1000_CTRL_EXT); + reg &= ~(1 << 23); + reg |= (1 << 22); + E1000_WRITE_REG(hw, E1000_CTRL_EXT, reg); + } + + /* PCI-Ex Control Register */ + if (hw->mac.type == e1000_82574) { + reg = E1000_READ_REG(hw, E1000_GCR); + reg |= (1 << 22); + E1000_WRITE_REG(hw, E1000_GCR, reg); + } + + return; +} + +/** + * e1000_clear_vfta_82571 - Clear VLAN filter table + * @hw: pointer to the HW structure + * + * Clears the register array which contains the VLAN filter table by + * setting all the values to 0. + **/ +static void e1000_clear_vfta_82571(struct e1000_hw *hw) +{ + u32 offset; + u32 vfta_value = 0; + u32 vfta_offset = 0; + u32 vfta_bit_in_reg = 0; + + DEBUGFUNC("e1000_clear_vfta_82571"); + + if (hw->mac.type == e1000_82573 || hw->mac.type == e1000_82574) { + if (hw->mng_cookie.vlan_id != 0) { + /* + * The VFTA is a 4096b bit-field, each identifying + * a single VLAN ID. The following operations + * determine which 32b entry (i.e. offset) into the + * array we want to set the VLAN ID (i.e. bit) of + * the manageability unit. + */ + vfta_offset = (hw->mng_cookie.vlan_id >> + E1000_VFTA_ENTRY_SHIFT) & + E1000_VFTA_ENTRY_MASK; + vfta_bit_in_reg = 1 << (hw->mng_cookie.vlan_id & + E1000_VFTA_ENTRY_BIT_SHIFT_MASK); + } + } + for (offset = 0; offset < E1000_VLAN_FILTER_TBL_SIZE; offset++) { + /* + * If the offset we want to clear is the same offset of the + * manageability VLAN ID, then clear all bits except that of + * the manageability unit. + */ + vfta_value = (offset == vfta_offset) ? vfta_bit_in_reg : 0; + E1000_WRITE_REG_ARRAY(hw, E1000_VFTA, offset, vfta_value); + E1000_WRITE_FLUSH(hw); + } +} + +/** + * e1000_check_mng_mode_82574 - Check manageability is enabled + * @hw: pointer to the HW structure + * + * Reads the NVM Initialization Control Word 2 and returns TRUE + * (>0) if any manageability is enabled, else FALSE (0). + **/ +static bool e1000_check_mng_mode_82574(struct e1000_hw *hw) +{ + u16 data; + + DEBUGFUNC("e1000_check_mng_mode_82574"); + + hw->nvm.ops.read(hw, NVM_INIT_CONTROL2_REG, 1, &data); + return (data & E1000_NVM_INIT_CTRL2_MNGM) != 0; +} + +/** + * e1000_led_on_82574 - Turn LED on + * @hw: pointer to the HW structure + * + * Turn LED on. + **/ +static s32 e1000_led_on_82574(struct e1000_hw *hw) +{ + u32 ctrl; + u32 i; + + DEBUGFUNC("e1000_led_on_82574"); + + ctrl = hw->mac.ledctl_mode2; + if (!(E1000_STATUS_LU & E1000_READ_REG(hw, E1000_STATUS))) { + /* + * If no link, then turn LED on by setting the invert bit + * for each LED that's "on" (0x0E) in ledctl_mode2. + */ + for (i = 0; i < 4; i++) + if (((hw->mac.ledctl_mode2 >> (i * 8)) & 0xFF) == + E1000_LEDCTL_MODE_LED_ON) + ctrl |= (E1000_LEDCTL_LED0_IVRT << (i * 8)); + } + E1000_WRITE_REG(hw, E1000_LEDCTL, ctrl); + + return E1000_SUCCESS; +} + +/** + * e1000_update_mc_addr_list_82571 - Update Multicast addresses + * @hw: pointer to the HW structure + * @mc_addr_list: array of multicast addresses to program + * @mc_addr_count: number of multicast addresses to program + * @rar_used_count: the first RAR register free to program + * @rar_count: total number of supported Receive Address Registers + * + * Updates the Receive Address Registers and Multicast Table Array. + * The caller must have a packed mc_addr_list of multicast addresses. + * The parameter rar_count will usually be hw->mac.rar_entry_count + * unless there are workarounds that change this. + **/ +static void e1000_update_mc_addr_list_82571(struct e1000_hw *hw, + u8 *mc_addr_list, u32 mc_addr_count, + u32 rar_used_count, u32 rar_count) +{ + DEBUGFUNC("e1000_update_mc_addr_list_82571"); + + if (e1000_get_laa_state_82571(hw)) + rar_count--; + + e1000_update_mc_addr_list_generic(hw, mc_addr_list, mc_addr_count, + rar_used_count, rar_count); +} + +/** + * e1000_setup_link_82571 - Setup flow control and link settings + * @hw: pointer to the HW structure + * + * Determines which flow control settings to use, then configures flow + * control. Calls the appropriate media-specific link configuration + * function. Assuming the adapter has a valid link partner, a valid link + * should be established. Assumes the hardware has previously been reset + * and the transmitter and receiver are not enabled. + **/ +static s32 e1000_setup_link_82571(struct e1000_hw *hw) +{ + DEBUGFUNC("e1000_setup_link_82571"); + + /* + * 82573 does not have a word in the NVM to determine + * the default flow control setting, so we explicitly + * set it to full. + */ + if ((hw->mac.type == e1000_82573 || hw->mac.type == e1000_82574) && + hw->fc.requested_mode == e1000_fc_default) + hw->fc.requested_mode = e1000_fc_full; + + return e1000_setup_link_generic(hw); +} + +/** + * e1000_setup_copper_link_82571 - Configure copper link settings + * @hw: pointer to the HW structure + * + * Configures the link for auto-neg or forced speed and duplex. Then we check + * for link, once link is established calls to configure collision distance + * and flow control are called. + **/ +static s32 e1000_setup_copper_link_82571(struct e1000_hw *hw) +{ + u32 ctrl, led_ctrl; + s32 ret_val; + + DEBUGFUNC("e1000_setup_copper_link_82571"); + + ctrl = E1000_READ_REG(hw, E1000_CTRL); + ctrl |= E1000_CTRL_SLU; + ctrl &= ~(E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX); + E1000_WRITE_REG(hw, E1000_CTRL, ctrl); + + switch (hw->phy.type) { + case e1000_phy_m88: + case e1000_phy_bm: + ret_val = e1000_copper_link_setup_m88(hw); + break; + case e1000_phy_igp_2: + ret_val = e1000_copper_link_setup_igp(hw); + /* Setup activity LED */ + led_ctrl = E1000_READ_REG(hw, E1000_LEDCTL); + led_ctrl &= IGP_ACTIVITY_LED_MASK; + led_ctrl |= (IGP_ACTIVITY_LED_ENABLE | IGP_LED3_MODE); + E1000_WRITE_REG(hw, E1000_LEDCTL, led_ctrl); + break; + default: + ret_val = -E1000_ERR_PHY; + break; + } + + if (ret_val) + goto out; + + ret_val = e1000_setup_copper_link_generic(hw); + +out: + return ret_val; +} + +/** + * e1000_setup_fiber_serdes_link_82571 - Setup link for fiber/serdes + * @hw: pointer to the HW structure + * + * Configures collision distance and flow control for fiber and serdes links. + * Upon successful setup, poll for link. + **/ +static s32 e1000_setup_fiber_serdes_link_82571(struct e1000_hw *hw) +{ + DEBUGFUNC("e1000_setup_fiber_serdes_link_82571"); + + switch (hw->mac.type) { + case e1000_82571: + case e1000_82572: + /* + * If SerDes loopback mode is entered, there is no form + * of reset to take the adapter out of that mode. So we + * have to explicitly take the adapter out of loopback + * mode. This prevents drivers from twiddling their thumbs + * if another tool failed to take it out of loopback mode. + */ + E1000_WRITE_REG(hw, E1000_SCTL, E1000_SCTL_DISABLE_SERDES_LOOPBACK); + break; + default: + break; + } + + return e1000_setup_fiber_serdes_link_generic(hw); +} + +/** + * e1000_valid_led_default_82571 - Verify a valid default LED config + * @hw: pointer to the HW structure + * @data: pointer to the NVM (EEPROM) + * + * Read the EEPROM for the current default LED configuration. If the + * LED configuration is not valid, set to a valid LED configuration. + **/ +static s32 e1000_valid_led_default_82571(struct e1000_hw *hw, u16 *data) +{ + s32 ret_val; + + DEBUGFUNC("e1000_valid_led_default_82571"); + + ret_val = hw->nvm.ops.read(hw, NVM_ID_LED_SETTINGS, 1, data); + if (ret_val) { + DEBUGOUT("NVM Read Error\n"); + goto out; + } + + if ((hw->mac.type == e1000_82573 || hw->mac.type == e1000_82574) && + *data == ID_LED_RESERVED_F746) + *data = ID_LED_DEFAULT_82573; + else if (*data == ID_LED_RESERVED_0000 || *data == ID_LED_RESERVED_FFFF) + *data = ID_LED_DEFAULT; +out: + return ret_val; +} + +/** + * e1000_get_laa_state_82571 - Get locally administered address state + * @hw: pointer to the HW structure + * + * Retrieve and return the current locally administered address state. + **/ +bool e1000_get_laa_state_82571(struct e1000_hw *hw) +{ + DEBUGFUNC("e1000_get_laa_state_82571"); + + if (hw->mac.type != e1000_82571) + return FALSE; + + return hw->dev_spec._82571.laa_is_present; +} + +/** + * e1000_set_laa_state_82571 - Set locally administered address state + * @hw: pointer to the HW structure + * @state: enable/disable locally administered address + * + * Enable/Disable the current locally administered address state. + **/ +void e1000_set_laa_state_82571(struct e1000_hw *hw, bool state) +{ + DEBUGFUNC("e1000_set_laa_state_82571"); + + if (hw->mac.type != e1000_82571) + return; + + hw->dev_spec._82571.laa_is_present = state; + + /* If workaround is activated... */ + if (state) + /* + * Hold a copy of the LAA in RAR[14] This is done so that + * between the time RAR[0] gets clobbered and the time it + * gets fixed, the actual LAA is in one of the RARs and no + * incoming packets directed to this port are dropped. + * Eventually the LAA will be in RAR[0] and RAR[14]. + */ + e1000_rar_set_generic(hw, hw->mac.addr, + hw->mac.rar_entry_count - 1); + return; +} + +/** + * e1000_fix_nvm_checksum_82571 - Fix EEPROM checksum + * @hw: pointer to the HW structure + * + * Verifies that the EEPROM has completed the update. After updating the + * EEPROM, we need to check bit 15 in work 0x23 for the checksum fix. If + * the checksum fix is not implemented, we need to set the bit and update + * the checksum. Otherwise, if bit 15 is set and the checksum is incorrect, + * we need to return bad checksum. + **/ +static s32 e1000_fix_nvm_checksum_82571(struct e1000_hw *hw) +{ + struct e1000_nvm_info *nvm = &hw->nvm; + s32 ret_val = E1000_SUCCESS; + u16 data; + + DEBUGFUNC("e1000_fix_nvm_checksum_82571"); + + if (nvm->type != e1000_nvm_flash_hw) + goto out; + + /* + * Check bit 4 of word 10h. If it is 0, firmware is done updating + * 10h-12h. Checksum may need to be fixed. + */ + ret_val = nvm->ops.read(hw, 0x10, 1, &data); + if (ret_val) + goto out; + + if (!(data & 0x10)) { + /* + * Read 0x23 and check bit 15. This bit is a 1 + * when the checksum has already been fixed. If + * the checksum is still wrong and this bit is a + * 1, we need to return bad checksum. Otherwise, + * we need to set this bit to a 1 and update the + * checksum. + */ + ret_val = nvm->ops.read(hw, 0x23, 1, &data); + if (ret_val) + goto out; + + if (!(data & 0x8000)) { + data |= 0x8000; + ret_val = nvm->ops.write(hw, 0x23, 1, &data); + if (ret_val) + goto out; + ret_val = nvm->ops.update(hw); + } + } + +out: + return ret_val; +} + +/** + * e1000_read_mac_addr_82571 - Read device MAC address + * @hw: pointer to the HW structure + **/ +static s32 e1000_read_mac_addr_82571(struct e1000_hw *hw) +{ + s32 ret_val = E1000_SUCCESS; + + DEBUGFUNC("e1000_read_mac_addr_82571"); + if (e1000_check_alt_mac_addr_generic(hw)) + ret_val = e1000_read_mac_addr_generic(hw); + + return ret_val; +} + +/** + * e1000_power_down_phy_copper_82571 - Remove link during PHY power down + * @hw: pointer to the HW structure + * + * In the case of a PHY power down to save power, or to turn off link during a + * driver unload, or wake on lan is not enabled, remove the link. + **/ +static void e1000_power_down_phy_copper_82571(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + struct e1000_mac_info *mac = &hw->mac; + + if (!(phy->ops.check_reset_block)) + return; + + /* If the management interface is not enabled, then power down */ + if (!(mac->ops.check_mng_mode(hw) || phy->ops.check_reset_block(hw))) + e1000_power_down_phy_copper(hw); + + return; +} + +/** + * e1000_clear_hw_cntrs_82571 - Clear device specific hardware counters + * @hw: pointer to the HW structure + * + * Clears the hardware counters by reading the counter registers. + **/ +static void e1000_clear_hw_cntrs_82571(struct e1000_hw *hw) +{ + DEBUGFUNC("e1000_clear_hw_cntrs_82571"); + + e1000_clear_hw_cntrs_base_generic(hw); + + E1000_READ_REG(hw, E1000_PRC64); + E1000_READ_REG(hw, E1000_PRC127); + E1000_READ_REG(hw, E1000_PRC255); + E1000_READ_REG(hw, E1000_PRC511); + E1000_READ_REG(hw, E1000_PRC1023); + E1000_READ_REG(hw, E1000_PRC1522); + E1000_READ_REG(hw, E1000_PTC64); + E1000_READ_REG(hw, E1000_PTC127); + E1000_READ_REG(hw, E1000_PTC255); + E1000_READ_REG(hw, E1000_PTC511); + E1000_READ_REG(hw, E1000_PTC1023); + E1000_READ_REG(hw, E1000_PTC1522); + + E1000_READ_REG(hw, E1000_ALGNERRC); + E1000_READ_REG(hw, E1000_RXERRC); + E1000_READ_REG(hw, E1000_TNCRS); + E1000_READ_REG(hw, E1000_CEXTERR); + E1000_READ_REG(hw, E1000_TSCTC); + E1000_READ_REG(hw, E1000_TSCTFC); + + E1000_READ_REG(hw, E1000_MGTPRC); + E1000_READ_REG(hw, E1000_MGTPDC); + E1000_READ_REG(hw, E1000_MGTPTC); + + E1000_READ_REG(hw, E1000_IAC); + E1000_READ_REG(hw, E1000_ICRXOC); + + E1000_READ_REG(hw, E1000_ICRXPTC); + E1000_READ_REG(hw, E1000_ICRXATC); + E1000_READ_REG(hw, E1000_ICTXPTC); + E1000_READ_REG(hw, E1000_ICTXATC); + E1000_READ_REG(hw, E1000_ICTXQEC); + E1000_READ_REG(hw, E1000_ICTXQMTC); + E1000_READ_REG(hw, E1000_ICRXDMTC); +} diff --git a/sys/dev/netif/ig_hal/e1000_82571.h b/sys/dev/netif/ig_hal/e1000_82571.h new file mode 100644 index 0000000000..5e66793c01 --- /dev/null +++ b/sys/dev/netif/ig_hal/e1000_82571.h @@ -0,0 +1,59 @@ +/****************************************************************************** + + Copyright (c) 2001-2008, Intel Corporation + All rights reserved. + + Redistribution and use in source and binary forms, with or without + modification, are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, + this list of conditions and the following disclaimer. + + 2. Redistributions in binary form must reproduce the above copyright + notice, this list of conditions and the following disclaimer in the + documentation and/or other materials provided with the distribution. + + 3. Neither the name of the Intel Corporation nor the names of its + contributors may be used to endorse or promote products derived from + this software without specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE + ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE + LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR + CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF + SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS + INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN + CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) + ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + POSSIBILITY OF SUCH DAMAGE. + +******************************************************************************/ +/*$FreeBSD$*/ + +#ifndef _E1000_82571_H_ +#define _E1000_82571_H_ + +#define ID_LED_RESERVED_F746 0xF746 +#define ID_LED_DEFAULT_82573 ((ID_LED_DEF1_DEF2 << 12) | \ + (ID_LED_OFF1_ON2 << 8) | \ + (ID_LED_DEF1_DEF2 << 4) | \ + (ID_LED_DEF1_DEF2)) + +#define E1000_GCR_L1_ACT_WITHOUT_L0S_RX 0x08000000 + +/* Intr Throttling - RW */ +#define E1000_EITR_82574(_n) (0x000E8 + (0x4 * (_n))) + +#define E1000_EIAC_82574 0x000DC /* Ext. Interrupt Auto Clear - RW */ +#define E1000_EIAC_MASK_82574 0x01F00000 + +#define E1000_NVM_INIT_CTRL2_MNGM 0x6000 /* Manageability Operation Mode mask */ + +#define E1000_RXCFGL 0x0B634 /* TimeSync Rx EtherType & Msg Type Reg - RW */ + +bool e1000_get_laa_state_82571(struct e1000_hw *hw); +void e1000_set_laa_state_82571(struct e1000_hw *hw, bool state); + +#endif diff --git a/sys/dev/netif/ig_hal/e1000_82575.c b/sys/dev/netif/ig_hal/e1000_82575.c new file mode 100644 index 0000000000..3d16447978 --- /dev/null +++ b/sys/dev/netif/ig_hal/e1000_82575.c @@ -0,0 +1,1669 @@ +/****************************************************************************** + + Copyright (c) 2001-2008, Intel Corporation + All rights reserved. + + Redistribution and use in source and binary forms, with or without + modification, are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, + this list of conditions and the following disclaimer. + + 2. Redistributions in binary form must reproduce the above copyright + notice, this list of conditions and the following disclaimer in the + documentation and/or other materials provided with the distribution. + + 3. Neither the name of the Intel Corporation nor the names of its + contributors may be used to endorse or promote products derived from + this software without specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE + ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE + LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR + CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF + SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS + INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN + CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) + ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + POSSIBILITY OF SUCH DAMAGE. + +******************************************************************************/ +/*$FreeBSD$*/ + +/* + * 82575EB Gigabit Network Connection + * 82575EB Gigabit Backplane Connection + * 82575GB Gigabit Network Connection + * 82576 Gigabit Network Connection + */ + +#include "e1000_api.h" + +static s32 e1000_init_phy_params_82575(struct e1000_hw *hw); +static s32 e1000_init_nvm_params_82575(struct e1000_hw *hw); +static s32 e1000_init_mac_params_82575(struct e1000_hw *hw); +static s32 e1000_acquire_phy_82575(struct e1000_hw *hw); +static void e1000_release_phy_82575(struct e1000_hw *hw); +static s32 e1000_acquire_nvm_82575(struct e1000_hw *hw); +static void e1000_release_nvm_82575(struct e1000_hw *hw); +static s32 e1000_check_for_link_82575(struct e1000_hw *hw); +static s32 e1000_get_cfg_done_82575(struct e1000_hw *hw); +static s32 e1000_get_link_up_info_82575(struct e1000_hw *hw, u16 *speed, + u16 *duplex); +static s32 e1000_init_hw_82575(struct e1000_hw *hw); +static s32 e1000_phy_hw_reset_sgmii_82575(struct e1000_hw *hw); +static s32 e1000_read_phy_reg_sgmii_82575(struct e1000_hw *hw, u32 offset, + u16 *data); +static s32 e1000_reset_hw_82575(struct e1000_hw *hw); +static s32 e1000_set_d0_lplu_state_82575(struct e1000_hw *hw, + bool active); +static s32 e1000_setup_copper_link_82575(struct e1000_hw *hw); +static s32 e1000_setup_fiber_serdes_link_82575(struct e1000_hw *hw); +static s32 e1000_valid_led_default_82575(struct e1000_hw *hw, u16 *data); +static s32 e1000_write_phy_reg_sgmii_82575(struct e1000_hw *hw, + u32 offset, u16 data); +static void e1000_clear_hw_cntrs_82575(struct e1000_hw *hw); +static s32 e1000_acquire_swfw_sync_82575(struct e1000_hw *hw, u16 mask); +static s32 e1000_configure_pcs_link_82575(struct e1000_hw *hw); +static s32 e1000_get_pcs_speed_and_duplex_82575(struct e1000_hw *hw, + u16 *speed, u16 *duplex); +static s32 e1000_get_phy_id_82575(struct e1000_hw *hw); +static void e1000_release_swfw_sync_82575(struct e1000_hw *hw, u16 mask); +static bool e1000_sgmii_active_82575(struct e1000_hw *hw); +static s32 e1000_reset_init_script_82575(struct e1000_hw *hw); +static s32 e1000_read_mac_addr_82575(struct e1000_hw *hw); +static void e1000_power_down_phy_copper_82575(struct e1000_hw *hw); + +static void e1000_init_rx_addrs_82575(struct e1000_hw *hw, u16 rar_count); +static void e1000_update_mc_addr_list_82575(struct e1000_hw *hw, + u8 *mc_addr_list, u32 mc_addr_count, + u32 rar_used_count, u32 rar_count); +void e1000_shutdown_fiber_serdes_link_82575(struct e1000_hw *hw); + +/** + * e1000_init_phy_params_82575 - Init PHY func ptrs. + * @hw: pointer to the HW structure + **/ +static s32 e1000_init_phy_params_82575(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val = E1000_SUCCESS; + + DEBUGFUNC("e1000_init_phy_params_82575"); + + if (hw->phy.media_type != e1000_media_type_copper) { + phy->type = e1000_phy_none; + goto out; + } else { + phy->ops.power_up = e1000_power_up_phy_copper; + phy->ops.power_down = e1000_power_down_phy_copper_82575; + } + + phy->autoneg_mask = AUTONEG_ADVERTISE_SPEED_DEFAULT; + phy->reset_delay_us = 100; + + phy->ops.acquire = e1000_acquire_phy_82575; + phy->ops.check_reset_block = e1000_check_reset_block_generic; + phy->ops.commit = e1000_phy_sw_reset_generic; + phy->ops.get_cfg_done = e1000_get_cfg_done_82575; + phy->ops.release = e1000_release_phy_82575; + + if (e1000_sgmii_active_82575(hw)) { + phy->ops.reset = e1000_phy_hw_reset_sgmii_82575; + phy->ops.read_reg = e1000_read_phy_reg_sgmii_82575; + phy->ops.write_reg = e1000_write_phy_reg_sgmii_82575; + } else { + phy->ops.reset = e1000_phy_hw_reset_generic; + phy->ops.read_reg = e1000_read_phy_reg_igp; + phy->ops.write_reg = e1000_write_phy_reg_igp; + } + + /* Set phy->phy_addr and phy->id. */ + ret_val = e1000_get_phy_id_82575(hw); + + /* Verify phy id and set remaining function pointers */ + switch (phy->id) { + case M88E1111_I_PHY_ID: + phy->type = e1000_phy_m88; + phy->ops.check_polarity = e1000_check_polarity_m88; + phy->ops.get_info = e1000_get_phy_info_m88; + phy->ops.get_cable_length = e1000_get_cable_length_m88; + phy->ops.force_speed_duplex = e1000_phy_force_speed_duplex_m88; + break; + case IGP03E1000_E_PHY_ID: + case IGP04E1000_E_PHY_ID: + phy->type = e1000_phy_igp_3; + phy->ops.check_polarity = e1000_check_polarity_igp; + phy->ops.get_info = e1000_get_phy_info_igp; + phy->ops.get_cable_length = e1000_get_cable_length_igp_2; + phy->ops.force_speed_duplex = e1000_phy_force_speed_duplex_igp; + phy->ops.set_d0_lplu_state = e1000_set_d0_lplu_state_82575; + phy->ops.set_d3_lplu_state = e1000_set_d3_lplu_state_generic; + break; + default: + ret_val = -E1000_ERR_PHY; + goto out; + } + +out: + return ret_val; +} + +/** + * e1000_init_nvm_params_82575 - Init NVM func ptrs. + * @hw: pointer to the HW structure + **/ +static s32 e1000_init_nvm_params_82575(struct e1000_hw *hw) +{ + struct e1000_nvm_info *nvm = &hw->nvm; + u32 eecd = E1000_READ_REG(hw, E1000_EECD); + u16 size; + + DEBUGFUNC("e1000_init_nvm_params_82575"); + + nvm->opcode_bits = 8; + nvm->delay_usec = 1; + switch (nvm->override) { + case e1000_nvm_override_spi_large: + nvm->page_size = 32; + nvm->address_bits = 16; + break; + case e1000_nvm_override_spi_small: + nvm->page_size = 8; + nvm->address_bits = 8; + break; + default: + nvm->page_size = eecd & E1000_EECD_ADDR_BITS ? 32 : 8; + nvm->address_bits = eecd & E1000_EECD_ADDR_BITS ? 16 : 8; + break; + } + + nvm->type = e1000_nvm_eeprom_spi; + + size = (u16)((eecd & E1000_EECD_SIZE_EX_MASK) >> + E1000_EECD_SIZE_EX_SHIFT); + + /* + * Added to a constant, "size" becomes the left-shift value + * for setting word_size. + */ + size += NVM_WORD_SIZE_BASE_SHIFT; + + /* EEPROM access above 16k is unsupported */ + if (size > 14) + size = 14; + nvm->word_size = 1 << size; + + /* Function Pointers */ + nvm->ops.acquire = e1000_acquire_nvm_82575; + nvm->ops.read = e1000_read_nvm_eerd; + nvm->ops.release = e1000_release_nvm_82575; + nvm->ops.update = e1000_update_nvm_checksum_generic; + nvm->ops.valid_led_default = e1000_valid_led_default_82575; + nvm->ops.validate = e1000_validate_nvm_checksum_generic; + nvm->ops.write = e1000_write_nvm_spi; + + return E1000_SUCCESS; +} + +/** + * e1000_init_mac_params_82575 - Init MAC func ptrs. + * @hw: pointer to the HW structure + **/ +static s32 e1000_init_mac_params_82575(struct e1000_hw *hw) +{ + struct e1000_mac_info *mac = &hw->mac; + struct e1000_dev_spec_82575 *dev_spec = &hw->dev_spec._82575; + u32 ctrl_ext = 0; + + DEBUGFUNC("e1000_init_mac_params_82575"); + + /* Set media type */ + /* + * The 82575 uses bits 22:23 for link mode. The mode can be changed + * based on the EEPROM. We cannot rely upon device ID. There + * is no distinguishable difference between fiber and internal + * SerDes mode on the 82575. There can be an external PHY attached + * on the SGMII interface. For this, we'll set sgmii_active to TRUE. + */ + hw->phy.media_type = e1000_media_type_copper; + dev_spec->sgmii_active = FALSE; + + ctrl_ext = E1000_READ_REG(hw, E1000_CTRL_EXT); + if ((ctrl_ext & E1000_CTRL_EXT_LINK_MODE_MASK) == + E1000_CTRL_EXT_LINK_MODE_PCIE_SERDES) { + hw->phy.media_type = e1000_media_type_internal_serdes; + ctrl_ext |= E1000_CTRL_I2C_ENA; + } else if (ctrl_ext & E1000_CTRL_EXT_LINK_MODE_SGMII) { + dev_spec->sgmii_active = TRUE; + ctrl_ext |= E1000_CTRL_I2C_ENA; + } else { + ctrl_ext &= ~E1000_CTRL_I2C_ENA; + } + E1000_WRITE_REG(hw, E1000_CTRL_EXT, ctrl_ext); + + /* Set mta register count */ + mac->mta_reg_count = 128; + /* Set rar entry count */ + mac->rar_entry_count = E1000_RAR_ENTRIES_82575; + if (mac->type == e1000_82576) + mac->rar_entry_count = E1000_RAR_ENTRIES_82576; + /* Set if part includes ASF firmware */ + mac->asf_firmware_present = TRUE; + /* Set if manageability features are enabled. */ + mac->arc_subsystem_valid = + (E1000_READ_REG(hw, E1000_FWSM) & E1000_FWSM_MODE_MASK) + ? TRUE : FALSE; + + /* Function pointers */ + + /* bus type/speed/width */ + mac->ops.get_bus_info = e1000_get_bus_info_pcie_generic; + /* reset */ + mac->ops.reset_hw = e1000_reset_hw_82575; + /* hw initialization */ + mac->ops.init_hw = e1000_init_hw_82575; + /* link setup */ + mac->ops.setup_link = e1000_setup_link_generic; + /* physical interface link setup */ + mac->ops.setup_physical_interface = + (hw->phy.media_type == e1000_media_type_copper) + ? e1000_setup_copper_link_82575 + : e1000_setup_fiber_serdes_link_82575; + /* physical interface shutdown */ + mac->ops.shutdown_serdes = e1000_shutdown_fiber_serdes_link_82575; + /* check for link */ + mac->ops.check_for_link = e1000_check_for_link_82575; + /* receive address register setting */ + mac->ops.rar_set = e1000_rar_set_generic; + /* read mac address */ + mac->ops.read_mac_addr = e1000_read_mac_addr_82575; + /* multicast address update */ + mac->ops.update_mc_addr_list = e1000_update_mc_addr_list_82575; + /* writing VFTA */ + mac->ops.write_vfta = e1000_write_vfta_generic; + /* clearing VFTA */ + mac->ops.clear_vfta = e1000_clear_vfta_generic; + /* setting MTA */ + mac->ops.mta_set = e1000_mta_set_generic; + /* blink LED */ + mac->ops.blink_led = e1000_blink_led_generic; + /* setup LED */ + mac->ops.setup_led = e1000_setup_led_generic; + /* cleanup LED */ + mac->ops.cleanup_led = e1000_cleanup_led_generic; + /* turn on/off LED */ + mac->ops.led_on = e1000_led_on_generic; + mac->ops.led_off = e1000_led_off_generic; + /* clear hardware counters */ + mac->ops.clear_hw_cntrs = e1000_clear_hw_cntrs_82575; + /* link info */ + mac->ops.get_link_up_info = e1000_get_link_up_info_82575; + + return E1000_SUCCESS; +} + +/** + * e1000_init_function_pointers_82575 - Init func ptrs. + * @hw: pointer to the HW structure + * + * Called to initialize all function pointers and parameters. + **/ +void e1000_init_function_pointers_82575(struct e1000_hw *hw) +{ + DEBUGFUNC("e1000_init_function_pointers_82575"); + + hw->mac.ops.init_params = e1000_init_mac_params_82575; + hw->nvm.ops.init_params = e1000_init_nvm_params_82575; + hw->phy.ops.init_params = e1000_init_phy_params_82575; +} + +/** + * e1000_acquire_phy_82575 - Acquire rights to access PHY + * @hw: pointer to the HW structure + * + * Acquire access rights to the correct PHY. + **/ +static s32 e1000_acquire_phy_82575(struct e1000_hw *hw) +{ + u16 mask; + + DEBUGFUNC("e1000_acquire_phy_82575"); + + mask = hw->bus.func ? E1000_SWFW_PHY1_SM : E1000_SWFW_PHY0_SM; + + return e1000_acquire_swfw_sync_82575(hw, mask); +} + +/** + * e1000_release_phy_82575 - Release rights to access PHY + * @hw: pointer to the HW structure + * + * A wrapper to release access rights to the correct PHY. + **/ +static void e1000_release_phy_82575(struct e1000_hw *hw) +{ + u16 mask; + + DEBUGFUNC("e1000_release_phy_82575"); + + mask = hw->bus.func ? E1000_SWFW_PHY1_SM : E1000_SWFW_PHY0_SM; + e1000_release_swfw_sync_82575(hw, mask); +} + +/** + * e1000_read_phy_reg_sgmii_82575 - Read PHY register using sgmii + * @hw: pointer to the HW structure + * @offset: register offset to be read + * @data: pointer to the read data + * + * Reads the PHY register at offset using the serial gigabit media independent + * interface and stores the retrieved information in data. + **/ +static s32 e1000_read_phy_reg_sgmii_82575(struct e1000_hw *hw, u32 offset, + u16 *data) +{ + struct e1000_phy_info *phy = &hw->phy; + u32 i, i2ccmd = 0; + + DEBUGFUNC("e1000_read_phy_reg_sgmii_82575"); + + if (offset > E1000_MAX_SGMII_PHY_REG_ADDR) { + DEBUGOUT1("PHY Address %u is out of range\n", offset); + return -E1000_ERR_PARAM; + } + + /* + * Set up Op-code, Phy Address, and register address in the I2CCMD + * register. The MAC will take care of interfacing with the + * PHY to retrieve the desired data. + */ + i2ccmd = ((offset << E1000_I2CCMD_REG_ADDR_SHIFT) | + (phy->addr << E1000_I2CCMD_PHY_ADDR_SHIFT) | + (E1000_I2CCMD_OPCODE_READ)); + + E1000_WRITE_REG(hw, E1000_I2CCMD, i2ccmd); + + /* Poll the ready bit to see if the I2C read completed */ + for (i = 0; i < E1000_I2CCMD_PHY_TIMEOUT; i++) { + usec_delay(50); + i2ccmd = E1000_READ_REG(hw, E1000_I2CCMD); + if (i2ccmd & E1000_I2CCMD_READY) + break; + } + if (!(i2ccmd & E1000_I2CCMD_READY)) { + DEBUGOUT("I2CCMD Read did not complete\n"); + return -E1000_ERR_PHY; + } + if (i2ccmd & E1000_I2CCMD_ERROR) { + DEBUGOUT("I2CCMD Error bit set\n"); + return -E1000_ERR_PHY; + } + + /* Need to byte-swap the 16-bit value. */ + *data = ((i2ccmd >> 8) & 0x00FF) | ((i2ccmd << 8) & 0xFF00); + + return E1000_SUCCESS; +} + +/** + * e1000_write_phy_reg_sgmii_82575 - Write PHY register using sgmii + * @hw: pointer to the HW structure + * @offset: register offset to write to + * @data: data to write at register offset + * + * Writes the data to PHY register at the offset using the serial gigabit + * media independent interface. + **/ +static s32 e1000_write_phy_reg_sgmii_82575(struct e1000_hw *hw, u32 offset, + u16 data) +{ + struct e1000_phy_info *phy = &hw->phy; + u32 i, i2ccmd = 0; + u16 phy_data_swapped; + + DEBUGFUNC("e1000_write_phy_reg_sgmii_82575"); + + if (offset > E1000_MAX_SGMII_PHY_REG_ADDR) { + DEBUGOUT1("PHY Address %d is out of range\n", offset); + return -E1000_ERR_PARAM; + } + + /* Swap the data bytes for the I2C interface */ + phy_data_swapped = ((data >> 8) & 0x00FF) | ((data << 8) & 0xFF00); + + /* + * Set up Op-code, Phy Address, and register address in the I2CCMD + * register. The MAC will take care of interfacing with the + * PHY to retrieve the desired data. + */ + i2ccmd = ((offset << E1000_I2CCMD_REG_ADDR_SHIFT) | + (phy->addr << E1000_I2CCMD_PHY_ADDR_SHIFT) | + E1000_I2CCMD_OPCODE_WRITE | + phy_data_swapped); + + E1000_WRITE_REG(hw, E1000_I2CCMD, i2ccmd); + + /* Poll the ready bit to see if the I2C read completed */ + for (i = 0; i < E1000_I2CCMD_PHY_TIMEOUT; i++) { + usec_delay(50); + i2ccmd = E1000_READ_REG(hw, E1000_I2CCMD); + if (i2ccmd & E1000_I2CCMD_READY) + break; + } + if (!(i2ccmd & E1000_I2CCMD_READY)) { + DEBUGOUT("I2CCMD Write did not complete\n"); + return -E1000_ERR_PHY; + } + if (i2ccmd & E1000_I2CCMD_ERROR) { + DEBUGOUT("I2CCMD Error bit set\n"); + return -E1000_ERR_PHY; + } + + return E1000_SUCCESS; +} + +/** + * e1000_get_phy_id_82575 - Retrieve PHY addr and id + * @hw: pointer to the HW structure + * + * Retrieves the PHY address and ID for both PHY's which do and do not use + * sgmi interface. + **/ +static s32 e1000_get_phy_id_82575(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val = E1000_SUCCESS; + u16 phy_id; + + DEBUGFUNC("e1000_get_phy_id_82575"); + + /* + * For SGMII PHYs, we try the list of possible addresses until + * we find one that works. For non-SGMII PHYs + * (e.g. integrated copper PHYs), an address of 1 should + * work. The result of this function should mean phy->phy_addr + * and phy->id are set correctly. + */ + if (!(e1000_sgmii_active_82575(hw))) { + phy->addr = 1; + ret_val = e1000_get_phy_id(hw); + goto out; + } + + /* + * The address field in the I2CCMD register is 3 bits and 0 is invalid. + * Therefore, we need to test 1-7 + */ + for (phy->addr = 1; phy->addr < 8; phy->addr++) { + ret_val = e1000_read_phy_reg_sgmii_82575(hw, PHY_ID1, &phy_id); + if (ret_val == E1000_SUCCESS) { + DEBUGOUT2("Vendor ID 0x%08X read at address %u\n", + phy_id, + phy->addr); + /* + * At the time of this writing, The M88 part is + * the only supported SGMII PHY product. + */ + if (phy_id == M88_VENDOR) + break; + } else { + DEBUGOUT1("PHY address %u was unreadable\n", + phy->addr); + } + } + + /* A valid PHY type couldn't be found. */ + if (phy->addr == 8) { + phy->addr = 0; + ret_val = -E1000_ERR_PHY; + goto out; + } + + ret_val = e1000_get_phy_id(hw); + +out: + return ret_val; +} + +/** + * e1000_phy_hw_reset_sgmii_82575 - Performs a PHY reset + * @hw: pointer to the HW structure + * + * Resets the PHY using the serial gigabit media independent interface. + **/ +static s32 e1000_phy_hw_reset_sgmii_82575(struct e1000_hw *hw) +{ + s32 ret_val = E1000_SUCCESS; + + DEBUGFUNC("e1000_phy_hw_reset_sgmii_82575"); + + /* + * This isn't a TRUE "hard" reset, but is the only reset + * available to us at this time. + */ + + DEBUGOUT("Soft resetting SGMII attached PHY...\n"); + + if (!(hw->phy.ops.write_reg)) + goto out; + + /* + * SFP documentation requires the following to configure the SPF module + * to work on SGMII. No further documentation is given. + */ + ret_val = hw->phy.ops.write_reg(hw, 0x1B, 0x8084); + if (ret_val) + goto out; + + ret_val = hw->phy.ops.commit(hw); + +out: + return ret_val; +} + +/** + * e1000_set_d0_lplu_state_82575 - Set Low Power Linkup D0 state + * @hw: pointer to the HW structure + * @active: TRUE to enable LPLU, FALSE to disable + * + * Sets the LPLU D0 state according to the active flag. When + * activating LPLU this function also disables smart speed + * and vice versa. LPLU will not be activated unless the + * device autonegotiation advertisement meets standards of + * either 10 or 10/100 or 10/100/1000 at all duplexes. + * This is a function pointer entry point only called by + * PHY setup routines. + **/ +static s32 e1000_set_d0_lplu_state_82575(struct e1000_hw *hw, bool active) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val = E1000_SUCCESS; + u16 data; + + DEBUGFUNC("e1000_set_d0_lplu_state_82575"); + + if (!(hw->phy.ops.read_reg)) + goto out; + + ret_val = phy->ops.read_reg(hw, IGP02E1000_PHY_POWER_MGMT, &data); + if (ret_val) + goto out; + + if (active) { + data |= IGP02E1000_PM_D0_LPLU; + ret_val = phy->ops.write_reg(hw, IGP02E1000_PHY_POWER_MGMT, + data); + if (ret_val) + goto out; + + /* When LPLU is enabled, we should disable SmartSpeed */ + ret_val = phy->ops.read_reg(hw, IGP01E1000_PHY_PORT_CONFIG, + &data); + data &= ~IGP01E1000_PSCFR_SMART_SPEED; + ret_val = phy->ops.write_reg(hw, IGP01E1000_PHY_PORT_CONFIG, + data); + if (ret_val) + goto out; + } else { + data &= ~IGP02E1000_PM_D0_LPLU; + ret_val = phy->ops.write_reg(hw, IGP02E1000_PHY_POWER_MGMT, + data); + /* + * LPLU and SmartSpeed are mutually exclusive. LPLU is used + * during Dx states where the power conservation is most + * important. During driver activity we should enable + * SmartSpeed, so performance is maintained. + */ + if (phy->smart_speed == e1000_smart_speed_on) { + ret_val = phy->ops.read_reg(hw, + IGP01E1000_PHY_PORT_CONFIG, + &data); + if (ret_val) + goto out; + + data |= IGP01E1000_PSCFR_SMART_SPEED; + ret_val = phy->ops.write_reg(hw, + IGP01E1000_PHY_PORT_CONFIG, + data); + if (ret_val) + goto out; + } else if (phy->smart_speed == e1000_smart_speed_off) { + ret_val = phy->ops.read_reg(hw, + IGP01E1000_PHY_PORT_CONFIG, + &data); + if (ret_val) + goto out; + + data &= ~IGP01E1000_PSCFR_SMART_SPEED; + ret_val = phy->ops.write_reg(hw, + IGP01E1000_PHY_PORT_CONFIG, + data); + if (ret_val) + goto out; + } + } + +out: + return ret_val; +} + +/** + * e1000_acquire_nvm_82575 - Request for access to EEPROM + * @hw: pointer to the HW structure + * + * Acquire the necessary semaphores for exclusive access to the EEPROM. + * Set the EEPROM access request bit and wait for EEPROM access grant bit. + * Return successful if access grant bit set, else clear the request for + * EEPROM access and return -E1000_ERR_NVM (-1). + **/ +static s32 e1000_acquire_nvm_82575(struct e1000_hw *hw) +{ + s32 ret_val; + + DEBUGFUNC("e1000_acquire_nvm_82575"); + + ret_val = e1000_acquire_swfw_sync_82575(hw, E1000_SWFW_EEP_SM); + if (ret_val) + goto out; + + ret_val = e1000_acquire_nvm_generic(hw); + + if (ret_val) + e1000_release_swfw_sync_82575(hw, E1000_SWFW_EEP_SM); + +out: + return ret_val; +} + +/** + * e1000_release_nvm_82575 - Release exclusive access to EEPROM + * @hw: pointer to the HW structure + * + * Stop any current commands to the EEPROM and clear the EEPROM request bit, + * then release the semaphores acquired. + **/ +static void e1000_release_nvm_82575(struct e1000_hw *hw) +{ + DEBUGFUNC("e1000_release_nvm_82575"); + + e1000_release_nvm_generic(hw); + e1000_release_swfw_sync_82575(hw, E1000_SWFW_EEP_SM); +} + +/** + * e1000_acquire_swfw_sync_82575 - Acquire SW/FW semaphore + * @hw: pointer to the HW structure + * @mask: specifies which semaphore to acquire + * + * Acquire the SW/FW semaphore to access the PHY or NVM. The mask + * will also specify which port we're acquiring the lock for. + **/ +static s32 e1000_acquire_swfw_sync_82575(struct e1000_hw *hw, u16 mask) +{ + u32 swfw_sync; + u32 swmask = mask; + u32 fwmask = mask << 16; + s32 ret_val = E1000_SUCCESS; + s32 i = 0, timeout = 200; /* FIXME: find real value to use here */ + + DEBUGFUNC("e1000_acquire_swfw_sync_82575"); + + while (i < timeout) { + if (e1000_get_hw_semaphore_generic(hw)) { + ret_val = -E1000_ERR_SWFW_SYNC; + goto out; + } + + swfw_sync = E1000_READ_REG(hw, E1000_SW_FW_SYNC); + if (!(swfw_sync & (fwmask | swmask))) + break; + + /* + * Firmware currently using resource (fwmask) + * or other software thread using resource (swmask) + */ + e1000_put_hw_semaphore_generic(hw); + msec_delay_irq(5); + i++; + } + + if (i == timeout) { + DEBUGOUT("Driver can't access resource, SW_FW_SYNC timeout.\n"); + ret_val = -E1000_ERR_SWFW_SYNC; + goto out; + } + + swfw_sync |= swmask; + E1000_WRITE_REG(hw, E1000_SW_FW_SYNC, swfw_sync); + + e1000_put_hw_semaphore_generic(hw); + +out: + return ret_val; +} + +/** + * e1000_release_swfw_sync_82575 - Release SW/FW semaphore + * @hw: pointer to the HW structure + * @mask: specifies which semaphore to acquire + * + * Release the SW/FW semaphore used to access the PHY or NVM. The mask + * will also specify which port we're releasing the lock for. + **/ +static void e1000_release_swfw_sync_82575(struct e1000_hw *hw, u16 mask) +{ + u32 swfw_sync; + + DEBUGFUNC("e1000_release_swfw_sync_82575"); + + while (e1000_get_hw_semaphore_generic(hw) != E1000_SUCCESS); + /* Empty */ + + swfw_sync = E1000_READ_REG(hw, E1000_SW_FW_SYNC); + swfw_sync &= ~mask; + E1000_WRITE_REG(hw, E1000_SW_FW_SYNC, swfw_sync); + + e1000_put_hw_semaphore_generic(hw); +} + +/** + * e1000_get_cfg_done_82575 - Read config done bit + * @hw: pointer to the HW structure + * + * Read the management control register for the config done bit for + * completion status. NOTE: silicon which is EEPROM-less will fail trying + * to read the config done bit, so an error is *ONLY* logged and returns + * E1000_SUCCESS. If we were to return with error, EEPROM-less silicon + * would not be able to be reset or change link. + **/ +static s32 e1000_get_cfg_done_82575(struct e1000_hw *hw) +{ + s32 timeout = PHY_CFG_TIMEOUT; + s32 ret_val = E1000_SUCCESS; + u32 mask = E1000_NVM_CFG_DONE_PORT_0; + + DEBUGFUNC("e1000_get_cfg_done_82575"); + + if (hw->bus.func == 1) + mask = E1000_NVM_CFG_DONE_PORT_1; + + while (timeout) { + if (E1000_READ_REG(hw, E1000_EEMNGCTL) & mask) + break; + msec_delay(1); + timeout--; + } + if (!timeout) { + DEBUGOUT("MNG configuration cycle has not completed.\n"); + } + + /* If EEPROM is not marked present, init the PHY manually */ + if (((E1000_READ_REG(hw, E1000_EECD) & E1000_EECD_PRES) == 0) && + (hw->phy.type == e1000_phy_igp_3)) { + e1000_phy_init_script_igp3(hw); + } + + return ret_val; +} + +/** + * e1000_get_link_up_info_82575 - Get link speed/duplex info + * @hw: pointer to the HW structure + * @speed: stores the current speed + * @duplex: stores the current duplex + * + * This is a wrapper function, if using the serial gigabit media independent + * interface, use PCS to retrieve the link speed and duplex information. + * Otherwise, use the generic function to get the link speed and duplex info. + **/ +static s32 e1000_get_link_up_info_82575(struct e1000_hw *hw, u16 *speed, + u16 *duplex) +{ + s32 ret_val; + + DEBUGFUNC("e1000_get_link_up_info_82575"); + + if (hw->phy.media_type != e1000_media_type_copper || + e1000_sgmii_active_82575(hw)) { + ret_val = e1000_get_pcs_speed_and_duplex_82575(hw, speed, + duplex); + } else { + ret_val = e1000_get_speed_and_duplex_copper_generic(hw, speed, + duplex); + } + + return ret_val; +} + +/** + * e1000_check_for_link_82575 - Check for link + * @hw: pointer to the HW structure + * + * If sgmii is enabled, then use the pcs register to determine link, otherwise + * use the generic interface for determining link. + **/ +static s32 e1000_check_for_link_82575(struct e1000_hw *hw) +{ + s32 ret_val; + u16 speed, duplex; + + DEBUGFUNC("e1000_check_for_link_82575"); + + /* SGMII link check is done through the PCS register. */ + if ((hw->phy.media_type != e1000_media_type_copper) || + (e1000_sgmii_active_82575(hw))) + ret_val = e1000_get_pcs_speed_and_duplex_82575(hw, &speed, + &duplex); + else + ret_val = e1000_check_for_copper_link_generic(hw); + + return ret_val; +} + +/** + * e1000_get_pcs_speed_and_duplex_82575 - Retrieve current speed/duplex + * @hw: pointer to the HW structure + * @speed: stores the current speed + * @duplex: stores the current duplex + * + * Using the physical coding sub-layer (PCS), retrieve the current speed and + * duplex, then store the values in the pointers provided. + **/ +static s32 e1000_get_pcs_speed_and_duplex_82575(struct e1000_hw *hw, + u16 *speed, u16 *duplex) +{ + struct e1000_mac_info *mac = &hw->mac; + u32 pcs; + + DEBUGFUNC("e1000_get_pcs_speed_and_duplex_82575"); + + /* Set up defaults for the return values of this function */ + mac->serdes_has_link = FALSE; + *speed = 0; + *duplex = 0; + + /* + * Read the PCS Status register for link state. For non-copper mode, + * the status register is not accurate. The PCS status register is + * used instead. + */ + pcs = E1000_READ_REG(hw, E1000_PCS_LSTAT); + + /* + * The link up bit determines when link is up on autoneg. The sync ok + * gets set once both sides sync up and agree upon link. Stable link + * can be determined by checking for both link up and link sync ok + */ + if ((pcs & E1000_PCS_LSTS_LINK_OK) && (pcs & E1000_PCS_LSTS_SYNK_OK)) { + mac->serdes_has_link = TRUE; + + /* Detect and store PCS speed */ + if (pcs & E1000_PCS_LSTS_SPEED_1000) { + *speed = SPEED_1000; + } else if (pcs & E1000_PCS_LSTS_SPEED_100) { + *speed = SPEED_100; + } else { + *speed = SPEED_10; + } + + /* Detect and store PCS duplex */ + if (pcs & E1000_PCS_LSTS_DUPLEX_FULL) { + *duplex = FULL_DUPLEX; + } else { + *duplex = HALF_DUPLEX; + } + } + + return E1000_SUCCESS; +} + +/** + * e1000_init_rx_addrs_82575 - Initialize receive address's + * @hw: pointer to the HW structure + * @rar_count: receive address registers + * + * Setups the receive address registers by setting the base receive address + * register to the devices MAC address and clearing all the other receive + * address registers to 0. + **/ +static void e1000_init_rx_addrs_82575(struct e1000_hw *hw, u16 rar_count) +{ + u32 i; + u8 addr[6] = {0,0,0,0,0,0}; + /* + * This function is essentially the same as that of + * e1000_init_rx_addrs_generic. However it also takes care + * of the special case where the register offset of the + * second set of RARs begins elsewhere. This is implicitly taken care by + * function e1000_rar_set_generic. + */ + + DEBUGFUNC("e1000_init_rx_addrs_82575"); + + /* Setup the receive address */ + DEBUGOUT("Programming MAC Address into RAR[0]\n"); + hw->mac.ops.rar_set(hw, hw->mac.addr, 0); + + /* Zero out the other (rar_entry_count - 1) receive addresses */ + DEBUGOUT1("Clearing RAR[1-%u]\n", rar_count-1); + for (i = 1; i < rar_count; i++) { + hw->mac.ops.rar_set(hw, addr, i); + } +} + +/** + * e1000_update_mc_addr_list_82575 - Update Multicast addresses + * @hw: pointer to the HW structure + * @mc_addr_list: array of multicast addresses to program + * @mc_addr_count: number of multicast addresses to program + * @rar_used_count: the first RAR register free to program + * @rar_count: total number of supported Receive Address Registers + * + * Updates the Receive Address Registers and Multicast Table Array. + * The caller must have a packed mc_addr_list of multicast addresses. + * The parameter rar_count will usually be hw->mac.rar_entry_count + * unless there are workarounds that change this. + **/ +static void e1000_update_mc_addr_list_82575(struct e1000_hw *hw, + u8 *mc_addr_list, u32 mc_addr_count, + u32 rar_used_count, u32 rar_count) +{ + u32 hash_value; + u32 i; + u8 addr[6] = {0,0,0,0,0,0}; + /* + * This function is essentially the same as that of + * e1000_update_mc_addr_list_generic. However it also takes care + * of the special case where the register offset of the + * second set of RARs begins elsewhere. This is implicitly taken care by + * function e1000_rar_set_generic. + */ + + DEBUGFUNC("e1000_update_mc_addr_list_82575"); + + /* + * Load the first set of multicast addresses into the exact + * filters (RAR). If there are not enough to fill the RAR + * array, clear the filters. + */ + for (i = rar_used_count; i < rar_count; i++) { + if (mc_addr_count) { + e1000_rar_set_generic(hw, mc_addr_list, i); + mc_addr_count--; + mc_addr_list += ETH_ADDR_LEN; + } else { + e1000_rar_set_generic(hw, addr, i); + } + } + + /* Clear the old settings from the MTA */ + DEBUGOUT("Clearing MTA\n"); + for (i = 0; i < hw->mac.mta_reg_count; i++) { + E1000_WRITE_REG_ARRAY(hw, E1000_MTA, i, 0); + E1000_WRITE_FLUSH(hw); + } + + /* Load any remaining multicast addresses into the hash table. */ + for (; mc_addr_count > 0; mc_addr_count--) { + hash_value = e1000_hash_mc_addr(hw, mc_addr_list); + DEBUGOUT1("Hash value = 0x%03X\n", hash_value); + hw->mac.ops.mta_set(hw, hash_value); + mc_addr_list += ETH_ADDR_LEN; + } +} + +/** + * e1000_shutdown_fiber_serdes_link_82575 - Remove link during power down + * @hw: pointer to the HW structure + * + * In the case of fiber serdes shut down optics and PCS on driver unload + * when management pass thru is not enabled. + **/ +void e1000_shutdown_fiber_serdes_link_82575(struct e1000_hw *hw) +{ + u32 reg; + u16 eeprom_data = 0; + + if (hw->mac.type != e1000_82576 || + (hw->phy.media_type != e1000_media_type_fiber && + hw->phy.media_type != e1000_media_type_internal_serdes)) + return; + + if (hw->bus.func == 0) + hw->nvm.ops.read(hw, NVM_INIT_CONTROL3_PORT_A, 1, &eeprom_data); + + /* + * If APM is not enabled in the EEPROM and management interface is + * not enabled, then power down. + */ + if (!(eeprom_data & E1000_NVM_APME_82575) && + !e1000_enable_mng_pass_thru(hw)) { + /* Disable PCS to turn off link */ + reg = E1000_READ_REG(hw, E1000_PCS_CFG0); + reg &= ~E1000_PCS_CFG_PCS_EN; + E1000_WRITE_REG(hw, E1000_PCS_CFG0, reg); + + /* shutdown the laser */ + reg = E1000_READ_REG(hw, E1000_CTRL_EXT); + reg |= E1000_CTRL_EXT_SDP7_DATA; + E1000_WRITE_REG(hw, E1000_CTRL_EXT, reg); + + /* flush the write to verfiy completion */ + E1000_WRITE_FLUSH(hw); + msec_delay(1); + } + + return; +} + +/** + * e1000_reset_hw_82575 - Reset hardware + * @hw: pointer to the HW structure + * + * This resets the hardware into a known state. + **/ +static s32 e1000_reset_hw_82575(struct e1000_hw *hw) +{ + u32 ctrl, icr; + s32 ret_val; + + DEBUGFUNC("e1000_reset_hw_82575"); + + /* + * Prevent the PCI-E bus from sticking if there is no TLP connection + * on the last TLP read/write transaction when MAC is reset. + */ + ret_val = e1000_disable_pcie_master_generic(hw); + if (ret_val) { + DEBUGOUT("PCI-E Master disable polling has failed.\n"); + } + + DEBUGOUT("Masking off all interrupts\n"); + E1000_WRITE_REG(hw, E1000_IMC, 0xffffffff); + + E1000_WRITE_REG(hw, E1000_RCTL, 0); + E1000_WRITE_REG(hw, E1000_TCTL, E1000_TCTL_PSP); + E1000_WRITE_FLUSH(hw); + + msec_delay(10); + + ctrl = E1000_READ_REG(hw, E1000_CTRL); + + DEBUGOUT("Issuing a global reset to MAC\n"); + E1000_WRITE_REG(hw, E1000_CTRL, ctrl | E1000_CTRL_RST); + + ret_val = e1000_get_auto_rd_done_generic(hw); + if (ret_val) { + /* + * When auto config read does not complete, do not + * return with an error. This can happen in situations + * where there is no eeprom and prevents getting link. + */ + DEBUGOUT("Auto Read Done did not complete\n"); + } + + /* If EEPROM is not present, run manual init scripts */ + if ((E1000_READ_REG(hw, E1000_EECD) & E1000_EECD_PRES) == 0) + e1000_reset_init_script_82575(hw); + + /* Clear any pending interrupt events. */ + E1000_WRITE_REG(hw, E1000_IMC, 0xffffffff); + icr = E1000_READ_REG(hw, E1000_ICR); + + e1000_check_alt_mac_addr_generic(hw); + + return ret_val; +} + +/** + * e1000_init_hw_82575 - Initialize hardware + * @hw: pointer to the HW structure + * + * This inits the hardware readying it for operation. + **/ +static s32 e1000_init_hw_82575(struct e1000_hw *hw) +{ + struct e1000_mac_info *mac = &hw->mac; + s32 ret_val; + u16 i, rar_count = mac->rar_entry_count; + + DEBUGFUNC("e1000_init_hw_82575"); + + /* Initialize identification LED */ + ret_val = e1000_id_led_init_generic(hw); + if (ret_val) { + DEBUGOUT("Error initializing identification LED\n"); + /* This is not fatal and we should not stop init due to this */ + } + + /* Disabling VLAN filtering */ + DEBUGOUT("Initializing the IEEE VLAN\n"); + mac->ops.clear_vfta(hw); + + /* Setup the receive address */ + e1000_init_rx_addrs_82575(hw, rar_count); + /* Zero out the Multicast HASH table */ + DEBUGOUT("Zeroing the MTA\n"); + for (i = 0; i < mac->mta_reg_count; i++) + E1000_WRITE_REG_ARRAY(hw, E1000_MTA, i, 0); + + /* Setup link and flow control */ + ret_val = mac->ops.setup_link(hw); + + /* + * Clear all of the statistics registers (clear on read). It is + * important that we do this after we have tried to establish link + * because the symbol error count will increment wildly if there + * is no link. + */ + e1000_clear_hw_cntrs_82575(hw); + + return ret_val; +} + +/** + * e1000_setup_copper_link_82575 - Configure copper link settings + * @hw: pointer to the HW structure + * + * Configures the link for auto-neg or forced speed and duplex. Then we check + * for link, once link is established calls to configure collision distance + * and flow control are called. + **/ +static s32 e1000_setup_copper_link_82575(struct e1000_hw *hw) +{ + u32 ctrl, led_ctrl; + s32 ret_val; + bool link; + + DEBUGFUNC("e1000_setup_copper_link_82575"); + + ctrl = E1000_READ_REG(hw, E1000_CTRL); + ctrl |= E1000_CTRL_SLU; + ctrl &= ~(E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX); + E1000_WRITE_REG(hw, E1000_CTRL, ctrl); + + switch (hw->phy.type) { + case e1000_phy_m88: + ret_val = e1000_copper_link_setup_m88(hw); + break; + case e1000_phy_igp_3: + ret_val = e1000_copper_link_setup_igp(hw); + /* Setup activity LED */ + led_ctrl = E1000_READ_REG(hw, E1000_LEDCTL); + led_ctrl &= IGP_ACTIVITY_LED_MASK; + led_ctrl |= (IGP_ACTIVITY_LED_ENABLE | IGP_LED3_MODE); + E1000_WRITE_REG(hw, E1000_LEDCTL, led_ctrl); + break; + default: + ret_val = -E1000_ERR_PHY; + break; + } + + if (ret_val) + goto out; + + if (hw->mac.autoneg) { + /* + * Setup autoneg and flow control advertisement + * and perform autonegotiation. + */ + ret_val = e1000_copper_link_autoneg(hw); + if (ret_val) + goto out; + } else { + /* + * PHY will be set to 10H, 10F, 100H or 100F + * depending on user settings. + */ + DEBUGOUT("Forcing Speed and Duplex\n"); + ret_val = hw->phy.ops.force_speed_duplex(hw); + if (ret_val) { + DEBUGOUT("Error Forcing Speed and Duplex\n"); + goto out; + } + } + + ret_val = e1000_configure_pcs_link_82575(hw); + if (ret_val) + goto out; + + /* + * Check link status. Wait up to 100 microseconds for link to become + * valid. + */ + ret_val = e1000_phy_has_link_generic(hw, + COPPER_LINK_UP_LIMIT, + 10, + &link); + if (ret_val) + goto out; + + if (link) { + DEBUGOUT("Valid link established!!!\n"); + /* Config the MAC and PHY after link is up */ + e1000_config_collision_dist_generic(hw); + ret_val = e1000_config_fc_after_link_up_generic(hw); + } else { + DEBUGOUT("Unable to establish link!!!\n"); + } + +out: + return ret_val; +} + +/** + * e1000_setup_fiber_serdes_link_82575 - Setup link for fiber/serdes + * @hw: pointer to the HW structure + * + * Configures speed and duplex for fiber and serdes links. + **/ +static s32 e1000_setup_fiber_serdes_link_82575(struct e1000_hw *hw) +{ + u32 reg; + + DEBUGFUNC("e1000_setup_fiber_serdes_link_82575"); + + /* + * On the 82575, SerDes loopback mode persists until it is + * explicitly turned off or a power cycle is performed. A read to + * the register does not indicate its status. Therefore, we ensure + * loopback mode is disabled during initialization. + */ + E1000_WRITE_REG(hw, E1000_SCTL, E1000_SCTL_DISABLE_SERDES_LOOPBACK); + + /* Force link up, set 1gb, set both sw defined pins */ + reg = E1000_READ_REG(hw, E1000_CTRL); + reg |= E1000_CTRL_SLU | + E1000_CTRL_SPD_1000 | + E1000_CTRL_FRCSPD | + E1000_CTRL_SWDPIN0 | + E1000_CTRL_SWDPIN1; + E1000_WRITE_REG(hw, E1000_CTRL, reg); + + /* Power on phy for 82576 fiber adapters */ + if (hw->mac.type == e1000_82576) { + reg = E1000_READ_REG(hw, E1000_CTRL_EXT); + reg &= ~E1000_CTRL_EXT_SDP7_DATA; + E1000_WRITE_REG(hw, E1000_CTRL_EXT, reg); + } + + /* Set switch control to serdes energy detect */ + reg = E1000_READ_REG(hw, E1000_CONNSW); + reg |= E1000_CONNSW_ENRGSRC; + E1000_WRITE_REG(hw, E1000_CONNSW, reg); + + /* + * New SerDes mode allows for forcing speed or autonegotiating speed + * at 1gb. Autoneg should be default set by most drivers. This is the + * mode that will be compatible with older link partners and switches. + * However, both are supported by the hardware and some drivers/tools. + */ + reg = E1000_READ_REG(hw, E1000_PCS_LCTL); + + reg &= ~(E1000_PCS_LCTL_AN_ENABLE | E1000_PCS_LCTL_FLV_LINK_UP | + E1000_PCS_LCTL_FSD | E1000_PCS_LCTL_FORCE_LINK); + + if (hw->mac.autoneg) { + /* Set PCS register for autoneg */ + reg |= E1000_PCS_LCTL_FSV_1000 | /* Force 1000 */ + E1000_PCS_LCTL_FDV_FULL | /* SerDes Full duplex */ + E1000_PCS_LCTL_AN_ENABLE | /* Enable Autoneg */ + E1000_PCS_LCTL_AN_RESTART; /* Restart autoneg */ + DEBUGOUT1("Configuring Autoneg; PCS_LCTL = 0x%08X\n", reg); + } else { + /* Set PCS register for forced speed */ + reg |= E1000_PCS_LCTL_FLV_LINK_UP | /* Force link up */ + E1000_PCS_LCTL_FSV_1000 | /* Force 1000 */ + E1000_PCS_LCTL_FDV_FULL | /* SerDes Full duplex */ + E1000_PCS_LCTL_FSD | /* Force Speed */ + E1000_PCS_LCTL_FORCE_LINK; /* Force Link */ + DEBUGOUT1("Configuring Forced Link; PCS_LCTL = 0x%08X\n", reg); + } + + if (hw->mac.type == e1000_82576) { + reg |= E1000_PCS_LCTL_FORCE_FCTRL; + e1000_force_mac_fc_generic(hw); + } + + E1000_WRITE_REG(hw, E1000_PCS_LCTL, reg); + + return E1000_SUCCESS; +} + +/** + * e1000_valid_led_default_82575 - Verify a valid default LED config + * @hw: pointer to the HW structure + * @data: pointer to the NVM (EEPROM) + * + * Read the EEPROM for the current default LED configuration. If the + * LED configuration is not valid, set to a valid LED configuration. + **/ +static s32 e1000_valid_led_default_82575(struct e1000_hw *hw, u16 *data) +{ + s32 ret_val; + + DEBUGFUNC("e1000_valid_led_default_82575"); + + ret_val = hw->nvm.ops.read(hw, NVM_ID_LED_SETTINGS, 1, data); + if (ret_val) { + DEBUGOUT("NVM Read Error\n"); + goto out; + } + + if (*data == ID_LED_RESERVED_0000 || *data == ID_LED_RESERVED_FFFF) { + switch(hw->phy.media_type) { + case e1000_media_type_fiber: + case e1000_media_type_internal_serdes: + *data = ID_LED_DEFAULT_82575_SERDES; + break; + case e1000_media_type_copper: + default: + *data = ID_LED_DEFAULT; + break; + } + } +out: + return ret_val; +} + +/** + * e1000_configure_pcs_link_82575 - Configure PCS link + * @hw: pointer to the HW structure + * + * Configure the physical coding sub-layer (PCS) link. The PCS link is + * only used on copper connections where the serialized gigabit media + * independent interface (sgmii) is being used. Configures the link + * for auto-negotiation or forces speed/duplex. + **/ +static s32 e1000_configure_pcs_link_82575(struct e1000_hw *hw) +{ + struct e1000_mac_info *mac = &hw->mac; + u32 reg = 0; + + DEBUGFUNC("e1000_configure_pcs_link_82575"); + + if (hw->phy.media_type != e1000_media_type_copper || + !(e1000_sgmii_active_82575(hw))) + goto out; + + /* For SGMII, we need to issue a PCS autoneg restart */ + reg = E1000_READ_REG(hw, E1000_PCS_LCTL); + + /* AN time out should be disabled for SGMII mode */ + reg &= ~(E1000_PCS_LCTL_AN_TIMEOUT); + + if (mac->autoneg) { + /* Make sure forced speed and force link are not set */ + reg &= ~(E1000_PCS_LCTL_FSD | E1000_PCS_LCTL_FORCE_LINK); + + /* + * The PHY should be setup prior to calling this function. + * All we need to do is restart autoneg and enable autoneg. + */ + reg |= E1000_PCS_LCTL_AN_RESTART | E1000_PCS_LCTL_AN_ENABLE; + } else { + /* Set PCS register for forced speed */ + + /* Turn off bits for full duplex, speed, and autoneg */ + reg &= ~(E1000_PCS_LCTL_FSV_1000 | + E1000_PCS_LCTL_FSV_100 | + E1000_PCS_LCTL_FDV_FULL | + E1000_PCS_LCTL_AN_ENABLE); + + /* Check for duplex first */ + if (mac->forced_speed_duplex & E1000_ALL_FULL_DUPLEX) + reg |= E1000_PCS_LCTL_FDV_FULL; + + /* Now set speed */ + if (mac->forced_speed_duplex & E1000_ALL_100_SPEED) + reg |= E1000_PCS_LCTL_FSV_100; + + /* Force speed and force link */ + reg |= E1000_PCS_LCTL_FSD | + E1000_PCS_LCTL_FORCE_LINK | + E1000_PCS_LCTL_FLV_LINK_UP; + + DEBUGOUT1("Wrote 0x%08X to PCS_LCTL to configure forced link\n", + reg); + } + E1000_WRITE_REG(hw, E1000_PCS_LCTL, reg); + +out: + return E1000_SUCCESS; +} + +/** + * e1000_sgmii_active_82575 - Return sgmii state + * @hw: pointer to the HW structure + * + * 82575 silicon has a serialized gigabit media independent interface (sgmii) + * which can be enabled for use in the embedded applications. Simply + * return the current state of the sgmii interface. + **/ +static bool e1000_sgmii_active_82575(struct e1000_hw *hw) +{ + struct e1000_dev_spec_82575 *dev_spec = &hw->dev_spec._82575; + + DEBUGFUNC("e1000_sgmii_active_82575"); + + if (hw->mac.type != e1000_82575 && hw->mac.type != e1000_82576) + return FALSE; + + return dev_spec->sgmii_active; +} + +/** + * e1000_reset_init_script_82575 - Inits HW defaults after reset + * @hw: pointer to the HW structure + * + * Inits recommended HW defaults after a reset when there is no EEPROM + * detected. This is only for the 82575. + **/ +static s32 e1000_reset_init_script_82575(struct e1000_hw* hw) +{ + DEBUGFUNC("e1000_reset_init_script_82575"); + + if (hw->mac.type == e1000_82575) { + DEBUGOUT("Running reset init script for 82575\n"); + /* SerDes configuration via SERDESCTRL */ + e1000_write_8bit_ctrl_reg_generic(hw, E1000_SCTL, 0x00, 0x0C); + e1000_write_8bit_ctrl_reg_generic(hw, E1000_SCTL, 0x01, 0x78); + e1000_write_8bit_ctrl_reg_generic(hw, E1000_SCTL, 0x1B, 0x23); + e1000_write_8bit_ctrl_reg_generic(hw, E1000_SCTL, 0x23, 0x15); + + /* CCM configuration via CCMCTL register */ + e1000_write_8bit_ctrl_reg_generic(hw, E1000_CCMCTL, 0x14, 0x00); + e1000_write_8bit_ctrl_reg_generic(hw, E1000_CCMCTL, 0x10, 0x00); + + /* PCIe lanes configuration */ + e1000_write_8bit_ctrl_reg_generic(hw, E1000_GIOCTL, 0x00, 0xEC); + e1000_write_8bit_ctrl_reg_generic(hw, E1000_GIOCTL, 0x61, 0xDF); + e1000_write_8bit_ctrl_reg_generic(hw, E1000_GIOCTL, 0x34, 0x05); + e1000_write_8bit_ctrl_reg_generic(hw, E1000_GIOCTL, 0x2F, 0x81); + + /* PCIe PLL Configuration */ + e1000_write_8bit_ctrl_reg_generic(hw, E1000_SCCTL, 0x02, 0x47); + e1000_write_8bit_ctrl_reg_generic(hw, E1000_SCCTL, 0x14, 0x00); + e1000_write_8bit_ctrl_reg_generic(hw, E1000_SCCTL, 0x10, 0x00); + } + + return E1000_SUCCESS; +} + +/** + * e1000_read_mac_addr_82575 - Read device MAC address + * @hw: pointer to the HW structure + **/ +static s32 e1000_read_mac_addr_82575(struct e1000_hw *hw) +{ + s32 ret_val = E1000_SUCCESS; + + DEBUGFUNC("e1000_read_mac_addr_82575"); + if (e1000_check_alt_mac_addr_generic(hw)) + ret_val = e1000_read_mac_addr_generic(hw); + + return ret_val; +} + +/** + * e1000_power_down_phy_copper_82575 - Remove link during PHY power down + * @hw: pointer to the HW structure + * + * In the case of a PHY power down to save power, or to turn off link during a + * driver unload, or wake on lan is not enabled, remove the link. + **/ +static void e1000_power_down_phy_copper_82575(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + struct e1000_mac_info *mac = &hw->mac; + + if (!(phy->ops.check_reset_block)) + return; + + /* If the management interface is not enabled, then power down */ + if (!(mac->ops.check_mng_mode(hw) || phy->ops.check_reset_block(hw))) + e1000_power_down_phy_copper(hw); + + return; +} + +/** + * e1000_clear_hw_cntrs_82575 - Clear device specific hardware counters + * @hw: pointer to the HW structure + * + * Clears the hardware counters by reading the counter registers. + **/ +static void e1000_clear_hw_cntrs_82575(struct e1000_hw *hw) +{ + DEBUGFUNC("e1000_clear_hw_cntrs_82575"); + + e1000_clear_hw_cntrs_base_generic(hw); + + E1000_READ_REG(hw, E1000_PRC64); + E1000_READ_REG(hw, E1000_PRC127); + E1000_READ_REG(hw, E1000_PRC255); + E1000_READ_REG(hw, E1000_PRC511); + E1000_READ_REG(hw, E1000_PRC1023); + E1000_READ_REG(hw, E1000_PRC1522); + E1000_READ_REG(hw, E1000_PTC64); + E1000_READ_REG(hw, E1000_PTC127); + E1000_READ_REG(hw, E1000_PTC255); + E1000_READ_REG(hw, E1000_PTC511); + E1000_READ_REG(hw, E1000_PTC1023); + E1000_READ_REG(hw, E1000_PTC1522); + + E1000_READ_REG(hw, E1000_ALGNERRC); + E1000_READ_REG(hw, E1000_RXERRC); + E1000_READ_REG(hw, E1000_TNCRS); + E1000_READ_REG(hw, E1000_CEXTERR); + E1000_READ_REG(hw, E1000_TSCTC); + E1000_READ_REG(hw, E1000_TSCTFC); + + E1000_READ_REG(hw, E1000_MGTPRC); + E1000_READ_REG(hw, E1000_MGTPDC); + E1000_READ_REG(hw, E1000_MGTPTC); + + E1000_READ_REG(hw, E1000_IAC); + E1000_READ_REG(hw, E1000_ICRXOC); + + E1000_READ_REG(hw, E1000_ICRXPTC); + E1000_READ_REG(hw, E1000_ICRXATC); + E1000_READ_REG(hw, E1000_ICTXPTC); + E1000_READ_REG(hw, E1000_ICTXATC); + E1000_READ_REG(hw, E1000_ICTXQEC); + E1000_READ_REG(hw, E1000_ICTXQMTC); + E1000_READ_REG(hw, E1000_ICRXDMTC); + + E1000_READ_REG(hw, E1000_CBTMPC); + E1000_READ_REG(hw, E1000_HTDPMC); + E1000_READ_REG(hw, E1000_CBRMPC); + E1000_READ_REG(hw, E1000_RPTHC); + E1000_READ_REG(hw, E1000_HGPTC); + E1000_READ_REG(hw, E1000_HTCBDPC); + E1000_READ_REG(hw, E1000_HGORCL); + E1000_READ_REG(hw, E1000_HGORCH); + E1000_READ_REG(hw, E1000_HGOTCL); + E1000_READ_REG(hw, E1000_HGOTCH); + E1000_READ_REG(hw, E1000_LENERRS); + + /* This register should not be read in copper configurations */ + if (hw->phy.media_type == e1000_media_type_internal_serdes) + E1000_READ_REG(hw, E1000_SCVPC); +} +/** + * e1000_rx_fifo_flush_82575 - Clean rx fifo after RX enable + * @hw: pointer to the HW structure + * + * After rx enable if managability is enabled then there is likely some + * bad data at the start of the fifo and possibly in the DMA fifo. This + * function clears the fifos and flushes any packets that came in as rx was + * being enabled. + **/ +void e1000_rx_fifo_flush_82575(struct e1000_hw *hw) +{ + u32 rctl, rlpml, rxdctl[4], rfctl, temp_rctl, rx_enabled; + int i, ms_wait; + + DEBUGFUNC("e1000_rx_fifo_workaround_82575"); + if (hw->mac.type != e1000_82575 || + !(E1000_READ_REG(hw, E1000_MANC) & E1000_MANC_RCV_TCO_EN)) + return; + + /* Disable all RX queues */ + for (i = 0; i < 4; i++) { + rxdctl[i] = E1000_READ_REG(hw, E1000_RXDCTL(i)); + E1000_WRITE_REG(hw, E1000_RXDCTL(i), + rxdctl[i] & ~E1000_RXDCTL_QUEUE_ENABLE); + } + /* Poll all queues to verify they have shut down */ + for (ms_wait = 0; ms_wait < 10; ms_wait++) { + msec_delay(1); + rx_enabled = 0; + for (i = 0; i < 4; i++) + rx_enabled |= E1000_READ_REG(hw, E1000_RXDCTL(i)); + if (!(rx_enabled & E1000_RXDCTL_QUEUE_ENABLE)) + break; + } + + if (ms_wait == 10) + DEBUGOUT("Queue disable timed out after 10ms\n"); + + /* Clear RLPML, RCTL.SBP, RFCTL.LEF, and set RCTL.LPE so that all + * incoming packets are rejected. Set enable and wait 2ms so that + * any packet that was coming in as RCTL.EN was set is flushed + */ + rfctl = E1000_READ_REG(hw, E1000_RFCTL); + E1000_WRITE_REG(hw, E1000_RFCTL, rfctl & ~E1000_RFCTL_LEF); + + rlpml = E1000_READ_REG(hw, E1000_RLPML); + E1000_WRITE_REG(hw, E1000_RLPML, 0); + + rctl = E1000_READ_REG(hw, E1000_RCTL); + temp_rctl = rctl & ~(E1000_RCTL_EN | E1000_RCTL_SBP); + temp_rctl |= E1000_RCTL_LPE; + + E1000_WRITE_REG(hw, E1000_RCTL, temp_rctl); + E1000_WRITE_REG(hw, E1000_RCTL, temp_rctl | E1000_RCTL_EN); + E1000_WRITE_FLUSH(hw); + msec_delay(2); + + /* Enable RX queues that were previously enabled and restore our + * previous state + */ + for (i = 0; i < 4; i++) + E1000_WRITE_REG(hw, E1000_RXDCTL(i), rxdctl[i]); + E1000_WRITE_REG(hw, E1000_RCTL, rctl); + E1000_WRITE_FLUSH(hw); + + E1000_WRITE_REG(hw, E1000_RLPML, rlpml); + E1000_WRITE_REG(hw, E1000_RFCTL, rfctl); + + /* Flush receive errors generated by workaround */ + E1000_READ_REG(hw, E1000_ROC); + E1000_READ_REG(hw, E1000_RNBC); + E1000_READ_REG(hw, E1000_MPC); +} + diff --git a/sys/dev/netif/ig_hal/e1000_82575.h b/sys/dev/netif/ig_hal/e1000_82575.h new file mode 100644 index 0000000000..56321e4d02 --- /dev/null +++ b/sys/dev/netif/ig_hal/e1000_82575.h @@ -0,0 +1,474 @@ +/****************************************************************************** + + Copyright (c) 2001-2008, Intel Corporation + All rights reserved. + + Redistribution and use in source and binary forms, with or without + modification, are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, + this list of conditions and the following disclaimer. + + 2. Redistributions in binary form must reproduce the above copyright + notice, this list of conditions and the following disclaimer in the + documentation and/or other materials provided with the distribution. + + 3. Neither the name of the Intel Corporation nor the names of its + contributors may be used to endorse or promote products derived from + this software without specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE + ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE + LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR + CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF + SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS + INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN + CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) + ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + POSSIBILITY OF SUCH DAMAGE. + +******************************************************************************/ +/*$FreeBSD$*/ + +#ifndef _E1000_82575_H_ +#define _E1000_82575_H_ + +#define ID_LED_DEFAULT_82575_SERDES ((ID_LED_DEF1_DEF2 << 12) | \ + (ID_LED_DEF1_DEF2 << 8) | \ + (ID_LED_DEF1_DEF2 << 4) | \ + (ID_LED_OFF1_ON2)) +/* + * Receive Address Register Count + * Number of high/low register pairs in the RAR. The RAR (Receive Address + * Registers) holds the directed and multicast addresses that we monitor. + * These entries are also used for MAC-based filtering. + */ +/* + * For 82576, there are an additional set of RARs that begin at an offset + * separate from the first set of RARs. + */ +#define E1000_RAR_ENTRIES_82575 16 +#define E1000_RAR_ENTRIES_82576 24 + +#ifdef E1000_BIT_FIELDS +struct e1000_adv_data_desc { + u64 buffer_addr; /* Address of the descriptor's data buffer */ + union { + u32 data; + struct { + u32 datalen :16; /* Data buffer length */ + u32 rsvd :4; + u32 dtyp :4; /* Descriptor type */ + u32 dcmd :8; /* Descriptor command */ + } config; + } lower; + union { + u32 data; + struct { + u32 status :4; /* Descriptor status */ + u32 idx :4; + u32 popts :6; /* Packet Options */ + u32 paylen :18; /* Payload length */ + } options; + } upper; +}; + +#define E1000_TXD_DTYP_ADV_C 0x2 /* Advanced Context Descriptor */ +#define E1000_TXD_DTYP_ADV_D 0x3 /* Advanced Data Descriptor */ +#define E1000_ADV_TXD_CMD_DEXT 0x20 /* Descriptor extension (0 = legacy) */ +#define E1000_ADV_TUCMD_IPV4 0x2 /* IP Packet Type: 1=IPv4 */ +#define E1000_ADV_TUCMD_IPV6 0x0 /* IP Packet Type: 0=IPv6 */ +#define E1000_ADV_TUCMD_L4T_UDP 0x0 /* L4 Packet TYPE of UDP */ +#define E1000_ADV_TUCMD_L4T_TCP 0x4 /* L4 Packet TYPE of TCP */ +#define E1000_ADV_TUCMD_MKRREQ 0x10 /* Indicates markers are required */ +#define E1000_ADV_DCMD_EOP 0x1 /* End of Packet */ +#define E1000_ADV_DCMD_IFCS 0x2 /* Insert FCS (Ethernet CRC) */ +#define E1000_ADV_DCMD_RS 0x8 /* Report Status */ +#define E1000_ADV_DCMD_VLE 0x40 /* Add VLAN tag */ +#define E1000_ADV_DCMD_TSE 0x80 /* TCP Seg enable */ +/* Extended Device Control */ +#define E1000_CTRL_EXT_NSICR 0x00000001 /* Disable Intr Clear all on read */ + +struct e1000_adv_context_desc { + union { + u32 ip_config; + struct { + u32 iplen :9; + u32 maclen :7; + u32 vlan_tag :16; + } fields; + } ip_setup; + u32 seq_num; + union { + u64 l4_config; + struct { + u32 mkrloc :9; + u32 tucmd :11; + u32 dtyp :4; + u32 adv :8; + u32 rsvd :4; + u32 idx :4; + u32 l4len :8; + u32 mss :16; + } fields; + } l4_setup; +}; +#endif + +/* SRRCTL bit definitions */ +#define E1000_SRRCTL_BSIZEPKT_SHIFT 10 /* Shift _right_ */ +#define E1000_SRRCTL_BSIZEHDRSIZE_MASK 0x00000F00 +#define E1000_SRRCTL_BSIZEHDRSIZE_SHIFT 2 /* Shift _left_ */ +#define E1000_SRRCTL_DESCTYPE_LEGACY 0x00000000 +#define E1000_SRRCTL_DESCTYPE_ADV_ONEBUF 0x02000000 +#define E1000_SRRCTL_DESCTYPE_HDR_SPLIT 0x04000000 +#define E1000_SRRCTL_DESCTYPE_HDR_SPLIT_ALWAYS 0x0A000000 +#define E1000_SRRCTL_DESCTYPE_HDR_REPLICATION 0x06000000 +#define E1000_SRRCTL_DESCTYPE_HDR_REPLICATION_LARGE_PKT 0x08000000 +#define E1000_SRRCTL_DESCTYPE_MASK 0x0E000000 + +#define E1000_SRRCTL_BSIZEPKT_MASK 0x0000007F +#define E1000_SRRCTL_BSIZEHDR_MASK 0x00003F00 + +#define E1000_TX_HEAD_WB_ENABLE 0x1 +#define E1000_TX_SEQNUM_WB_ENABLE 0x2 + +#define E1000_MRQC_ENABLE_RSS_4Q 0x00000002 +#define E1000_MRQC_ENABLE_VMDQ 0x00000003 +#define E1000_MRQC_RSS_FIELD_IPV4_UDP 0x00400000 +#define E1000_MRQC_RSS_FIELD_IPV6_UDP 0x00800000 +#define E1000_MRQC_RSS_FIELD_IPV6_UDP_EX 0x01000000 + +#define E1000_VMRCTL_MIRROR_PORT_SHIFT 8 +#define E1000_VMRCTL_MIRROR_DSTPORT_MASK (7 << E1000_VMRCTL_MIRROR_PORT_SHIFT) +#define E1000_VMRCTL_POOL_MIRROR_ENABLE (1 << 0) +#define E1000_VMRCTL_UPLINK_MIRROR_ENABLE (1 << 1) +#define E1000_VMRCTL_DOWNLINK_MIRROR_ENABLE (1 << 2) + +#define E1000_EICR_TX_QUEUE ( \ + E1000_EICR_TX_QUEUE0 | \ + E1000_EICR_TX_QUEUE1 | \ + E1000_EICR_TX_QUEUE2 | \ + E1000_EICR_TX_QUEUE3) + +#define E1000_EICR_RX_QUEUE ( \ + E1000_EICR_RX_QUEUE0 | \ + E1000_EICR_RX_QUEUE1 | \ + E1000_EICR_RX_QUEUE2 | \ + E1000_EICR_RX_QUEUE3) + +#define E1000_EIMS_RX_QUEUE E1000_EICR_RX_QUEUE +#define E1000_EIMS_TX_QUEUE E1000_EICR_TX_QUEUE + +#define EIMS_ENABLE_MASK ( \ + E1000_EIMS_RX_QUEUE | \ + E1000_EIMS_TX_QUEUE | \ + E1000_EIMS_TCP_TIMER | \ + E1000_EIMS_OTHER) + +/* Immediate Interrupt Rx (A.K.A. Low Latency Interrupt) */ +#define E1000_IMIR_PORT_IM_EN 0x00010000 /* TCP port enable */ +#define E1000_IMIR_PORT_BP 0x00020000 /* TCP port check bypass */ +#define E1000_IMIREXT_SIZE_BP 0x00001000 /* Packet size bypass */ +#define E1000_IMIREXT_CTRL_URG 0x00002000 /* Check URG bit in header */ +#define E1000_IMIREXT_CTRL_ACK 0x00004000 /* Check ACK bit in header */ +#define E1000_IMIREXT_CTRL_PSH 0x00008000 /* Check PSH bit in header */ +#define E1000_IMIREXT_CTRL_RST 0x00010000 /* Check RST bit in header */ +#define E1000_IMIREXT_CTRL_SYN 0x00020000 /* Check SYN bit in header */ +#define E1000_IMIREXT_CTRL_FIN 0x00040000 /* Check FIN bit in header */ +#define E1000_IMIREXT_CTRL_BP 0x00080000 /* Bypass check of ctrl bits */ + +/* Receive Descriptor - Advanced */ +union e1000_adv_rx_desc { + struct { + u64 pkt_addr; /* Packet buffer address */ + u64 hdr_addr; /* Header buffer address */ + } read; + struct { + struct { + union { + u32 data; + struct { + u16 pkt_info; /* RSS type, Packet type */ + u16 hdr_info; /* Split Header, + * header buffer length */ + } hs_rss; + } lo_dword; + union { + u32 rss; /* RSS Hash */ + struct { + u16 ip_id; /* IP id */ + u16 csum; /* Packet Checksum */ + } csum_ip; + } hi_dword; + } lower; + struct { + u32 status_error; /* ext status/error */ + u16 length; /* Packet length */ + u16 vlan; /* VLAN tag */ + } upper; + } wb; /* writeback */ +}; + +#define E1000_RXDADV_RSSTYPE_MASK 0x0000F000 +#define E1000_RXDADV_RSSTYPE_SHIFT 12 +#define E1000_RXDADV_HDRBUFLEN_MASK 0x7FE0 +#define E1000_RXDADV_HDRBUFLEN_SHIFT 5 +#define E1000_RXDADV_SPLITHEADER_EN 0x00001000 +#define E1000_RXDADV_SPH 0x8000 +#define E1000_RXDADV_ERR_HBO 0x00800000 + +/* RSS Hash results */ +#define E1000_RXDADV_RSSTYPE_NONE 0x00000000 +#define E1000_RXDADV_RSSTYPE_IPV4_TCP 0x00000001 +#define E1000_RXDADV_RSSTYPE_IPV4 0x00000002 +#define E1000_RXDADV_RSSTYPE_IPV6_TCP 0x00000003 +#define E1000_RXDADV_RSSTYPE_IPV6_EX 0x00000004 +#define E1000_RXDADV_RSSTYPE_IPV6 0x00000005 +#define E1000_RXDADV_RSSTYPE_IPV6_TCP_EX 0x00000006 +#define E1000_RXDADV_RSSTYPE_IPV4_UDP 0x00000007 +#define E1000_RXDADV_RSSTYPE_IPV6_UDP 0x00000008 +#define E1000_RXDADV_RSSTYPE_IPV6_UDP_EX 0x00000009 + +/* RSS Packet Types as indicated in the receive descriptor */ +#define E1000_RXDADV_PKTTYPE_NONE 0x00000000 +#define E1000_RXDADV_PKTTYPE_IPV4 0x00000010 /* IPV4 hdr present */ +#define E1000_RXDADV_PKTTYPE_IPV4_EX 0x00000020 /* IPV4 hdr + extensions */ +#define E1000_RXDADV_PKTTYPE_IPV6 0x00000040 /* IPV6 hdr present */ +#define E1000_RXDADV_PKTTYPE_IPV6_EX 0x00000080 /* IPV6 hdr + extensions */ +#define E1000_RXDADV_PKTTYPE_TCP 0x00000100 /* TCP hdr present */ +#define E1000_RXDADV_PKTTYPE_UDP 0x00000200 /* UDP hdr present */ +#define E1000_RXDADV_PKTTYPE_SCTP 0x00000400 /* SCTP hdr present */ +#define E1000_RXDADV_PKTTYPE_NFS 0x00000800 /* NFS hdr present */ + +#define E1000_RXDADV_PKTTYPE_IPSEC_ESP 0x00001000 /* IPSec ESP */ +#define E1000_RXDADV_PKTTYPE_IPSEC_AH 0x00002000 /* IPSec AH */ +#define E1000_RXDADV_PKTTYPE_LINKSEC 0x00004000 /* LinkSec Encap */ +#define E1000_RXDADV_PKTTYPE_ETQF 0x00008000 /* PKTTYPE is ETQF index */ +#define E1000_RXDADV_PKTTYPE_ETQF_MASK 0x00000070 /* ETQF has 8 indices */ +#define E1000_RXDADV_PKTTYPE_ETQF_SHIFT 4 /* Right-shift 4 bits */ + +/* LinkSec results */ +/* Security Processing bit Indication */ +#define E1000_RXDADV_LNKSEC_STATUS_SECP 0x00020000 +#define E1000_RXDADV_LNKSEC_ERROR_BIT_MASK 0x18000000 +#define E1000_RXDADV_LNKSEC_ERROR_NO_SA_MATCH 0x08000000 +#define E1000_RXDADV_LNKSEC_ERROR_REPLAY_ERROR 0x10000000 +#define E1000_RXDADV_LNKSEC_ERROR_BAD_SIG 0x18000000 + +#define E1000_RXDADV_IPSEC_STATUS_SECP 0x00020000 +#define E1000_RXDADV_IPSEC_ERROR_BIT_MASK 0x18000000 +#define E1000_RXDADV_IPSEC_ERROR_INVALID_PROTOCOL 0x08000000 +#define E1000_RXDADV_IPSEC_ERROR_INVALID_LENGTH 0x10000000 +#define E1000_RXDADV_IPSEC_ERROR_AUTHENTICATION_FAILED 0x18000000 + +/* Transmit Descriptor - Advanced */ +union e1000_adv_tx_desc { + struct { + u64 buffer_addr; /* Address of descriptor's data buf */ + u32 cmd_type_len; + u32 olinfo_status; + } read; + struct { + u64 rsvd; /* Reserved */ + u32 nxtseq_seed; + u32 status; + } wb; +}; + +/* Adv Transmit Descriptor Config Masks */ +#define E1000_ADVTXD_DTYP_CTXT 0x00200000 /* Advanced Context Descriptor */ +#define E1000_ADVTXD_DTYP_DATA 0x00300000 /* Advanced Data Descriptor */ +#define E1000_ADVTXD_DCMD_EOP 0x01000000 /* End of Packet */ +#define E1000_ADVTXD_DCMD_IFCS 0x02000000 /* Insert FCS (Ethernet CRC) */ +#define E1000_ADVTXD_DCMD_RS 0x08000000 /* Report Status */ +#define E1000_ADVTXD_DCMD_DDTYP_ISCSI 0x10000000 /* DDP hdr type or iSCSI */ +#define E1000_ADVTXD_DCMD_DEXT 0x20000000 /* Descriptor extension (1=Adv) */ +#define E1000_ADVTXD_DCMD_VLE 0x40000000 /* VLAN pkt enable */ +#define E1000_ADVTXD_DCMD_TSE 0x80000000 /* TCP Seg enable */ +#define E1000_ADVTXD_MAC_LINKSEC 0x00040000 /* Apply LinkSec on packet */ +#define E1000_ADVTXD_MAC_TSTAMP 0x00080000 /* IEEE1588 Timestamp packet */ +#define E1000_ADVTXD_STAT_SN_CRC 0x00000002 /* NXTSEQ/SEED present in WB */ +#define E1000_ADVTXD_IDX_SHIFT 4 /* Adv desc Index shift */ +#define E1000_ADVTXD_POPTS_ISCO_1ST 0x00000000 /* 1st TSO of iSCSI PDU */ +#define E1000_ADVTXD_POPTS_ISCO_MDL 0x00000800 /* Middle TSO of iSCSI PDU */ +#define E1000_ADVTXD_POPTS_ISCO_LAST 0x00001000 /* Last TSO of iSCSI PDU */ +#define E1000_ADVTXD_POPTS_ISCO_FULL 0x00001800 /* 1st&Last TSO-full iSCSI PDU*/ +#define E1000_ADVTXD_POPTS_IPSEC 0x00000400 /* IPSec offload request */ +#define E1000_ADVTXD_PAYLEN_SHIFT 14 /* Adv desc PAYLEN shift */ + +/* Context descriptors */ +struct e1000_adv_tx_context_desc { + u32 vlan_macip_lens; + u32 seqnum_seed; + u32 type_tucmd_mlhl; + u32 mss_l4len_idx; +}; + +#define E1000_ADVTXD_MACLEN_SHIFT 9 /* Adv ctxt desc mac len shift */ +#define E1000_ADVTXD_VLAN_SHIFT 16 /* Adv ctxt vlan tag shift */ +#define E1000_ADVTXD_TUCMD_IPV4 0x00000400 /* IP Packet Type: 1=IPv4 */ +#define E1000_ADVTXD_TUCMD_IPV6 0x00000000 /* IP Packet Type: 0=IPv6 */ +#define E1000_ADVTXD_TUCMD_L4T_UDP 0x00000000 /* L4 Packet TYPE of UDP */ +#define E1000_ADVTXD_TUCMD_L4T_TCP 0x00000800 /* L4 Packet TYPE of TCP */ +#define E1000_ADVTXD_TUCMD_IPSEC_TYPE_ESP 0x00002000 /* IPSec Type ESP */ +/* IPSec Encrypt Enable for ESP */ +#define E1000_ADVTXD_TUCMD_IPSEC_ENCRYPT_EN 0x00004000 +#define E1000_ADVTXD_TUCMD_MKRREQ 0x00002000 /* Req requires Markers and CRC */ +#define E1000_ADVTXD_L4LEN_SHIFT 8 /* Adv ctxt L4LEN shift */ +#define E1000_ADVTXD_MSS_SHIFT 16 /* Adv ctxt MSS shift */ +/* Adv ctxt IPSec SA IDX mask */ +#define E1000_ADVTXD_IPSEC_SA_INDEX_MASK 0x000000FF +/* Adv ctxt IPSec ESP len mask */ +#define E1000_ADVTXD_IPSEC_ESP_LEN_MASK 0x000000FF + +/* Additional Transmit Descriptor Control definitions */ +#define E1000_TXDCTL_QUEUE_ENABLE 0x02000000 /* Enable specific Tx Queue */ +#define E1000_TXDCTL_SWFLSH 0x04000000 /* Tx Desc. write-back flushing */ +/* Tx Queue Arbitration Priority 0=low, 1=high */ +#define E1000_TXDCTL_PRIORITY 0x08000000 + +/* Additional Receive Descriptor Control definitions */ +#define E1000_RXDCTL_QUEUE_ENABLE 0x02000000 /* Enable specific Rx Queue */ +#define E1000_RXDCTL_SWFLSH 0x04000000 /* Rx Desc. write-back flushing */ + +/* Direct Cache Access (DCA) definitions */ +#define E1000_DCA_CTRL_DCA_ENABLE 0x00000000 /* DCA Enable */ +#define E1000_DCA_CTRL_DCA_DISABLE 0x00000001 /* DCA Disable */ + +#define E1000_DCA_CTRL_DCA_MODE_CB1 0x00 /* DCA Mode CB1 */ +#define E1000_DCA_CTRL_DCA_MODE_CB2 0x02 /* DCA Mode CB2 */ + +#define E1000_DCA_RXCTRL_CPUID_MASK 0x0000001F /* Rx CPUID Mask */ +#define E1000_DCA_RXCTRL_DESC_DCA_EN (1 << 5) /* DCA Rx Desc enable */ +#define E1000_DCA_RXCTRL_HEAD_DCA_EN (1 << 6) /* DCA Rx Desc header enable */ +#define E1000_DCA_RXCTRL_DATA_DCA_EN (1 << 7) /* DCA Rx Desc payload enable */ + +#define E1000_DCA_TXCTRL_CPUID_MASK 0x0000001F /* Tx CPUID Mask */ +#define E1000_DCA_TXCTRL_DESC_DCA_EN (1 << 5) /* DCA Tx Desc enable */ +#define E1000_DCA_TXCTRL_TX_WB_RO_EN (1 << 11) /* Tx Desc writeback RO bit */ + +#define E1000_DCA_TXCTRL_CPUID_MASK_82576 0xFF000000 /* Tx CPUID Mask */ +#define E1000_DCA_RXCTRL_CPUID_MASK_82576 0xFF000000 /* Rx CPUID Mask */ +#define E1000_DCA_TXCTRL_CPUID_SHIFT_82576 24 /* Tx CPUID */ +#define E1000_DCA_RXCTRL_CPUID_SHIFT_82576 24 /* Rx CPUID */ + +/* Additional interrupt register bit definitions */ +#define E1000_ICR_LSECPNS 0x00000020 /* PN threshold - server */ +#define E1000_IMS_LSECPNS E1000_ICR_LSECPNS /* PN threshold - server */ +#define E1000_ICS_LSECPNS E1000_ICR_LSECPNS /* PN threshold - server */ + +/* ETQF register bit definitions */ +#define E1000_ETQF_FILTER_ENABLE (1 << 26) +#define E1000_ETQF_IMM_INT (1 << 29) +#define E1000_ETQF_1588 (1 << 30) +#define E1000_ETQF_QUEUE_ENABLE (1 << 31) +/* + * ETQF filter list: one static filter per filter consumer. This is + * to avoid filter collisions later. Add new filters + * here!! + * + * Current filters: + * EAPOL 802.1x (0x888e): Filter 0 + */ +#define E1000_ETQF_FILTER_EAPOL 0 + +#define E1000_NVM_APME_82575 0x0400 +#define MAX_NUM_VFS 8 + +#define E1000_DTXSWC_MAC_SPOOF_MASK 0x000000FF /* Per VF MAC spoof control */ +#define E1000_DTXSWC_VLAN_SPOOF_MASK 0x0000FF00 /* Per VF VLAN spoof control */ +#define E1000_DTXSWC_LLE_MASK 0x00FF0000 /* Per VF Local LB enables */ +#define E1000_DTXSWC_VMDQ_LOOPBACK_EN (1 << 31) /* global VF LB enable */ + +/* Easy defines for setting default pool, would normally be left a zero */ +#define E1000_VT_CTL_DEFAULT_POOL_SHIFT 7 +#define E1000_VT_CTL_DEFAULT_POOL_MASK (0x7 << E1000_VT_CTL_DEFAULT_POOL_SHIFT) + +/* Other useful VMD_CTL register defines */ +#define E1000_VT_CTL_IGNORE_MAC (1 << 28) +#define E1000_VT_CTL_DISABLE_DEF_POOL (1 << 29) +#define E1000_VT_CTL_VM_REPL_EN (1 << 30) + +/* Per VM Offload register setup */ +#define E1000_VMOLR_LPE 0x00010000 /* Accept Long packet */ +#define E1000_VMOLR_AUPE 0x01000000 /* Accept untagged packets */ +#define E1000_VMOLR_BAM 0x08000000 /* Accept Broadcast packets */ +#define E1000_VMOLR_MPME 0x10000000 /* Multicast promiscuous mode */ +#define E1000_VMOLR_STRVLAN 0x40000000 /* Vlan stripping enable */ + +#define E1000_V2PMAILBOX_REQ 0x00000001 /* Request for PF Ready bit */ +#define E1000_V2PMAILBOX_ACK 0x00000002 /* Ack PF message received */ +#define E1000_V2PMAILBOX_VFU 0x00000004 /* VF owns the mailbox buffer */ +#define E1000_V2PMAILBOX_PFU 0x00000008 /* PF owns the mailbox buffer */ +#define E1000_V2PMAILBOX_PFSTS 0x00000010 /* PF wrote a message in the MB */ +#define E1000_V2PMAILBOX_PFACK 0x00000020 /* PF ack the previous VF msg */ +#define E1000_V2PMAILBOX_RSTI 0x00000040 /* PF has reset indication */ + +#define E1000_P2VMAILBOX_STS 0x00000001 /* Initiate message send to VF */ +#define E1000_P2VMAILBOX_ACK 0x00000002 /* Ack message recv'd from VF */ +#define E1000_P2VMAILBOX_VFU 0x00000004 /* VF owns the mailbox buffer */ +#define E1000_P2VMAILBOX_PFU 0x00000008 /* PF owns the mailbox buffer */ +#define E1000_P2VMAILBOX_RVFU 0x00000010 /* Reset VFU - used when VF stuck */ + +#define E1000_VFMAILBOX_SIZE 16 /* 16 32 bit words - 64 bytes */ + +/* If it's a E1000_VF_* msg then it originates in the VF and is sent to the + * PF. The reverse is TRUE if it is E1000_PF_*. + * Message ACK's are the value or'd with 0xF0000000 + */ +#define E1000_VT_MSGTYPE_ACK 0xF0000000 /* Messages below or'd with + * this are the ACK */ +#define E1000_VT_MSGTYPE_NACK 0xFF000000 /* Messages below or'd with + * this are the NACK */ +#define E1000_VT_MSGINFO_SHIFT 16 +/* bits 23:16 are used for exra info for certain messages */ +#define E1000_VT_MSGINFO_MASK (0xFF << E1000_VT_MSGINFO_SHIFT) + +#define E1000_VF_MSGTYPE_REQ_MAC 1 /* VF needs to know its MAC */ +#define E1000_VF_MSGTYPE_VFLR 2 /* VF notifies VFLR to PF */ +#define E1000_VF_SET_MULTICAST 3 /* VF requests PF to set MC addr */ +#define E1000_VF_SET_VLAN 4 /* VF requests PF to set VLAN */ + +/* Add 100h to all PF msgs, leaves room for up to 255 discrete message types + * from VF to PF - way more than we'll ever need */ +#define E1000_PF_MSGTYPE_RESET (1 + 0x100) /* PF notifies global reset + * imminent to VF */ +#define E1000_PF_MSGTYPE_LSC (2 + 0x100) /* PF notifies VF of LSC... VF + * will see extra msg info for + * status */ + +#define E1000_PF_MSG_LSCDOWN (1 << E1000_VT_MSGINFO_SHIFT) +#define E1000_PF_MSG_LSCUP (2 << E1000_VT_MSGINFO_SHIFT) + +#define ALL_QUEUES 0xFFFF + +s32 e1000_send_mail_to_pf_vf(struct e1000_hw *hw, u32 *msg, + s16 size); +s32 e1000_receive_mail_from_pf_vf(struct e1000_hw *hw, + u32 *msg, s16 size); +s32 e1000_send_mail_to_vf(struct e1000_hw *hw, u32 *msg, + u32 vf_number, s16 size); +s32 e1000_receive_mail_from_vf(struct e1000_hw *hw, u32 *msg, + u32 vf_number, s16 size); +void e1000_vmdq_loopback_enable_vf(struct e1000_hw *hw); +void e1000_vmdq_loopback_disable_vf(struct e1000_hw *hw); +void e1000_vmdq_replication_enable_vf(struct e1000_hw *hw, u32 enables); +void e1000_vmdq_replication_disable_vf(struct e1000_hw *hw); +void e1000_vmdq_enable_replication_mode_vf(struct e1000_hw *hw); +void e1000_vmdq_broadcast_replication_enable_vf(struct e1000_hw *hw, + u32 enables); +void e1000_vmdq_multicast_replication_enable_vf(struct e1000_hw *hw, + u32 enables); +void e1000_vmdq_broadcast_replication_disable_vf(struct e1000_hw *hw, + u32 disables); +void e1000_vmdq_multicast_replication_disable_vf(struct e1000_hw *hw, + u32 disables); +bool e1000_check_for_pf_ack_vf(struct e1000_hw *hw); + +bool e1000_check_for_pf_mail_vf(struct e1000_hw *hw, u32*); + + +#endif diff --git a/sys/dev/netif/ig_hal/e1000_api.c b/sys/dev/netif/ig_hal/e1000_api.c new file mode 100644 index 0000000000..47bffb5d3f --- /dev/null +++ b/sys/dev/netif/ig_hal/e1000_api.c @@ -0,0 +1,1230 @@ +/****************************************************************************** + + Copyright (c) 2001-2008, Intel Corporation + All rights reserved. + + Redistribution and use in source and binary forms, with or without + modification, are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, + this list of conditions and the following disclaimer. + + 2. Redistributions in binary form must reproduce the above copyright + notice, this list of conditions and the following disclaimer in the + documentation and/or other materials provided with the distribution. + + 3. Neither the name of the Intel Corporation nor the names of its + contributors may be used to endorse or promote products derived from + this software without specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE + ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE + LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR + CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF + SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS + INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN + CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) + ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + POSSIBILITY OF SUCH DAMAGE. + +******************************************************************************/ +/*$FreeBSD$*/ + +#include "e1000_api.h" + +/** + * e1000_init_mac_params - Initialize MAC function pointers + * @hw: pointer to the HW structure + * + * This function initializes the function pointers for the MAC + * set of functions. Called by drivers or by e1000_setup_init_funcs. + **/ +s32 e1000_init_mac_params(struct e1000_hw *hw) +{ + s32 ret_val = E1000_SUCCESS; + + if (hw->mac.ops.init_params) { + ret_val = hw->mac.ops.init_params(hw); + if (ret_val) { + DEBUGOUT("MAC Initialization Error\n"); + goto out; + } + } else { + DEBUGOUT("mac.init_mac_params was NULL\n"); + ret_val = -E1000_ERR_CONFIG; + } + +out: + return ret_val; +} + +/** + * e1000_init_nvm_params - Initialize NVM function pointers + * @hw: pointer to the HW structure + * + * This function initializes the function pointers for the NVM + * set of functions. Called by drivers or by e1000_setup_init_funcs. + **/ +s32 e1000_init_nvm_params(struct e1000_hw *hw) +{ + s32 ret_val = E1000_SUCCESS; + + if (hw->nvm.ops.init_params) { + ret_val = hw->nvm.ops.init_params(hw); + if (ret_val) { + DEBUGOUT("NVM Initialization Error\n"); + goto out; + } + } else { + DEBUGOUT("nvm.init_nvm_params was NULL\n"); + ret_val = -E1000_ERR_CONFIG; + } + +out: + return ret_val; +} + +/** + * e1000_init_phy_params - Initialize PHY function pointers + * @hw: pointer to the HW structure + * + * This function initializes the function pointers for the PHY + * set of functions. Called by drivers or by e1000_setup_init_funcs. + **/ +s32 e1000_init_phy_params(struct e1000_hw *hw) +{ + s32 ret_val = E1000_SUCCESS; + + if (hw->phy.ops.init_params) { + ret_val = hw->phy.ops.init_params(hw); + if (ret_val) { + DEBUGOUT("PHY Initialization Error\n"); + goto out; + } + } else { + DEBUGOUT("phy.init_phy_params was NULL\n"); + ret_val = -E1000_ERR_CONFIG; + } + +out: + return ret_val; +} + +/** + * e1000_set_mac_type - Sets MAC type + * @hw: pointer to the HW structure + * + * This function sets the mac type of the adapter based on the + * device ID stored in the hw structure. + * MUST BE FIRST FUNCTION CALLED (explicitly or through + * e1000_setup_init_funcs()). + **/ +s32 e1000_set_mac_type(struct e1000_hw *hw) +{ + struct e1000_mac_info *mac = &hw->mac; + s32 ret_val = E1000_SUCCESS; + + DEBUGFUNC("e1000_set_mac_type"); + + switch (hw->device_id) { + case E1000_DEV_ID_82542: + mac->type = e1000_82542; + break; + case E1000_DEV_ID_82543GC_FIBER: + case E1000_DEV_ID_82543GC_COPPER: + mac->type = e1000_82543; + break; + case E1000_DEV_ID_82544EI_COPPER: + case E1000_DEV_ID_82544EI_FIBER: + case E1000_DEV_ID_82544GC_COPPER: + case E1000_DEV_ID_82544GC_LOM: + mac->type = e1000_82544; + break; + case E1000_DEV_ID_82540EM: + case E1000_DEV_ID_82540EM_LOM: + case E1000_DEV_ID_82540EP: + case E1000_DEV_ID_82540EP_LOM: + case E1000_DEV_ID_82540EP_LP: + mac->type = e1000_82540; + break; + case E1000_DEV_ID_82545EM_COPPER: + case E1000_DEV_ID_82545EM_FIBER: + mac->type = e1000_82545; + break; + case E1000_DEV_ID_82545GM_COPPER: + case E1000_DEV_ID_82545GM_FIBER: + case E1000_DEV_ID_82545GM_SERDES: + mac->type = e1000_82545_rev_3; + break; + case E1000_DEV_ID_82546EB_COPPER: + case E1000_DEV_ID_82546EB_FIBER: + case E1000_DEV_ID_82546EB_QUAD_COPPER: + mac->type = e1000_82546; + break; + case E1000_DEV_ID_82546GB_COPPER: + case E1000_DEV_ID_82546GB_FIBER: + case E1000_DEV_ID_82546GB_SERDES: + case E1000_DEV_ID_82546GB_PCIE: + case E1000_DEV_ID_82546GB_QUAD_COPPER: + case E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3: + mac->type = e1000_82546_rev_3; + break; + case E1000_DEV_ID_82541EI: + case E1000_DEV_ID_82541EI_MOBILE: + case E1000_DEV_ID_82541ER_LOM: + mac->type = e1000_82541; + break; + case E1000_DEV_ID_82541ER: + case E1000_DEV_ID_82541GI: + case E1000_DEV_ID_82541GI_LF: + case E1000_DEV_ID_82541GI_MOBILE: + mac->type = e1000_82541_rev_2; + break; + case E1000_DEV_ID_82547EI: + case E1000_DEV_ID_82547EI_MOBILE: + mac->type = e1000_82547; + break; + case E1000_DEV_ID_82547GI: + mac->type = e1000_82547_rev_2; + break; + case E1000_DEV_ID_82571EB_COPPER: + case E1000_DEV_ID_82571EB_FIBER: + case E1000_DEV_ID_82571EB_SERDES: + case E1000_DEV_ID_82571EB_SERDES_DUAL: + case E1000_DEV_ID_82571EB_SERDES_QUAD: + case E1000_DEV_ID_82571EB_QUAD_COPPER: + case E1000_DEV_ID_82571PT_QUAD_COPPER: + case E1000_DEV_ID_82571EB_QUAD_FIBER: + case E1000_DEV_ID_82571EB_QUAD_COPPER_LP: + mac->type = e1000_82571; + break; + case E1000_DEV_ID_82572EI: + case E1000_DEV_ID_82572EI_COPPER: + case E1000_DEV_ID_82572EI_FIBER: + case E1000_DEV_ID_82572EI_SERDES: + mac->type = e1000_82572; + break; + case E1000_DEV_ID_82573E: + case E1000_DEV_ID_82573E_IAMT: + case E1000_DEV_ID_82573L: + mac->type = e1000_82573; + break; + case E1000_DEV_ID_82574L: + mac->type = e1000_82574; + break; + case E1000_DEV_ID_80003ES2LAN_COPPER_DPT: + case E1000_DEV_ID_80003ES2LAN_SERDES_DPT: + case E1000_DEV_ID_80003ES2LAN_COPPER_SPT: + case E1000_DEV_ID_80003ES2LAN_SERDES_SPT: + mac->type = e1000_80003es2lan; + break; + case E1000_DEV_ID_ICH8_IFE: + case E1000_DEV_ID_ICH8_IFE_GT: + case E1000_DEV_ID_ICH8_IFE_G: + case E1000_DEV_ID_ICH8_IGP_M: + case E1000_DEV_ID_ICH8_IGP_M_AMT: + case E1000_DEV_ID_ICH8_IGP_AMT: + case E1000_DEV_ID_ICH8_IGP_C: + mac->type = e1000_ich8lan; + break; + case E1000_DEV_ID_ICH9_IFE: + case E1000_DEV_ID_ICH9_IFE_GT: + case E1000_DEV_ID_ICH9_IFE_G: + case E1000_DEV_ID_ICH9_IGP_M: + case E1000_DEV_ID_ICH9_IGP_M_AMT: + case E1000_DEV_ID_ICH9_IGP_M_V: + case E1000_DEV_ID_ICH9_IGP_AMT: + case E1000_DEV_ID_ICH9_BM: + case E1000_DEV_ID_ICH9_IGP_C: + case E1000_DEV_ID_ICH10_R_BM_LM: + case E1000_DEV_ID_ICH10_R_BM_LF: + case E1000_DEV_ID_ICH10_R_BM_V: + mac->type = e1000_ich9lan; + break; + case E1000_DEV_ID_ICH10_D_BM_LM: + case E1000_DEV_ID_ICH10_D_BM_LF: + mac->type = e1000_ich10lan; + break; + case E1000_DEV_ID_82575EB_COPPER: + case E1000_DEV_ID_82575EB_FIBER_SERDES: + case E1000_DEV_ID_82575GB_QUAD_COPPER: + mac->type = e1000_82575; + break; + case E1000_DEV_ID_82576: + case E1000_DEV_ID_82576_FIBER: + case E1000_DEV_ID_82576_SERDES: + case E1000_DEV_ID_82576_QUAD_COPPER: + mac->type = e1000_82576; + break; + default: + /* Should never have loaded on this device */ + ret_val = -E1000_ERR_MAC_INIT; + break; + } + + return ret_val; +} + +/** + * e1000_setup_init_funcs - Initializes function pointers + * @hw: pointer to the HW structure + * @init_device: TRUE will initialize the rest of the function pointers + * getting the device ready for use. FALSE will only set + * MAC type and the function pointers for the other init + * functions. Passing FALSE will not generate any hardware + * reads or writes. + * + * This function must be called by a driver in order to use the rest + * of the 'shared' code files. Called by drivers only. + **/ +s32 e1000_setup_init_funcs(struct e1000_hw *hw, bool init_device) +{ + s32 ret_val; + + /* Can't do much good without knowing the MAC type. */ + ret_val = e1000_set_mac_type(hw); + if (ret_val) { + DEBUGOUT("ERROR: MAC type could not be set properly.\n"); + goto out; + } + + if (!hw->hw_addr) { + DEBUGOUT("ERROR: Registers not mapped\n"); + ret_val = -E1000_ERR_CONFIG; + goto out; + } + + /* + * Init function pointers to generic implementations. We do this first + * allowing a driver module to override it afterward. + */ + e1000_init_mac_ops_generic(hw); + e1000_init_phy_ops_generic(hw); + e1000_init_nvm_ops_generic(hw); + + /* + * Set up the init function pointers. These are functions within the + * adapter family file that sets up function pointers for the rest of + * the functions in that family. + */ + switch (hw->mac.type) { + case e1000_82542: + e1000_init_function_pointers_82542(hw); + break; + case e1000_82543: + case e1000_82544: + e1000_init_function_pointers_82543(hw); + break; + case e1000_82540: + case e1000_82545: + case e1000_82545_rev_3: + case e1000_82546: + case e1000_82546_rev_3: + e1000_init_function_pointers_82540(hw); + break; + case e1000_82541: + case e1000_82541_rev_2: + case e1000_82547: + case e1000_82547_rev_2: + e1000_init_function_pointers_82541(hw); + break; + case e1000_82571: + case e1000_82572: + case e1000_82573: + case e1000_82574: + e1000_init_function_pointers_82571(hw); + break; + case e1000_80003es2lan: + e1000_init_function_pointers_80003es2lan(hw); + break; + case e1000_ich8lan: + case e1000_ich9lan: + case e1000_ich10lan: + e1000_init_function_pointers_ich8lan(hw); + break; + case e1000_82575: + case e1000_82576: + e1000_init_function_pointers_82575(hw); + break; + default: + DEBUGOUT("Hardware not supported\n"); + ret_val = -E1000_ERR_CONFIG; + break; + } + + /* + * Initialize the rest of the function pointers. These require some + * register reads/writes in some cases. + */ + if (!(ret_val) && init_device) { + ret_val = e1000_init_mac_params(hw); + if (ret_val) + goto out; + + ret_val = e1000_init_nvm_params(hw); + if (ret_val) + goto out; + + ret_val = e1000_init_phy_params(hw); + if (ret_val) + goto out; + + } + +out: + return ret_val; +} + +/** + * e1000_get_bus_info - Obtain bus information for adapter + * @hw: pointer to the HW structure + * + * This will obtain information about the HW bus for which the + * adapter is attached and stores it in the hw structure. This is a + * function pointer entry point called by drivers. + **/ +s32 e1000_get_bus_info(struct e1000_hw *hw) +{ + if (hw->mac.ops.get_bus_info) + return hw->mac.ops.get_bus_info(hw); + + return E1000_SUCCESS; +} + +/** + * e1000_clear_vfta - Clear VLAN filter table + * @hw: pointer to the HW structure + * + * This clears the VLAN filter table on the adapter. This is a function + * pointer entry point called by drivers. + **/ +void e1000_clear_vfta(struct e1000_hw *hw) +{ + if (hw->mac.ops.clear_vfta) + hw->mac.ops.clear_vfta(hw); +} + +/** + * e1000_write_vfta - Write value to VLAN filter table + * @hw: pointer to the HW structure + * @offset: the 32-bit offset in which to write the value to. + * @value: the 32-bit value to write at location offset. + * + * This writes a 32-bit value to a 32-bit offset in the VLAN filter + * table. This is a function pointer entry point called by drivers. + **/ +void e1000_write_vfta(struct e1000_hw *hw, u32 offset, u32 value) +{ + if (hw->mac.ops.write_vfta) + hw->mac.ops.write_vfta(hw, offset, value); +} + +/** + * e1000_update_mc_addr_list - Update Multicast addresses + * @hw: pointer to the HW structure + * @mc_addr_list: array of multicast addresses to program + * @mc_addr_count: number of multicast addresses to program + * @rar_used_count: the first RAR register free to program + * @rar_count: total number of supported Receive Address Registers + * + * Updates the Receive Address Registers and Multicast Table Array. + * The caller must have a packed mc_addr_list of multicast addresses. + * The parameter rar_count will usually be hw->mac.rar_entry_count + * unless there are workarounds that change this. Currently no func pointer + * exists and all implementations are handled in the generic version of this + * function. + **/ +void e1000_update_mc_addr_list(struct e1000_hw *hw, u8 *mc_addr_list, + u32 mc_addr_count, u32 rar_used_count, + u32 rar_count) +{ + if (hw->mac.ops.update_mc_addr_list) + hw->mac.ops.update_mc_addr_list(hw, + mc_addr_list, + mc_addr_count, + rar_used_count, + rar_count); +} + +/** + * e1000_force_mac_fc - Force MAC flow control + * @hw: pointer to the HW structure + * + * Force the MAC's flow control settings. Currently no func pointer exists + * and all implementations are handled in the generic version of this + * function. + **/ +s32 e1000_force_mac_fc(struct e1000_hw *hw) +{ + return e1000_force_mac_fc_generic(hw); +} + +/** + * e1000_check_for_link - Check/Store link connection + * @hw: pointer to the HW structure + * + * This checks the link condition of the adapter and stores the + * results in the hw->mac structure. This is a function pointer entry + * point called by drivers. + **/ +s32 e1000_check_for_link(struct e1000_hw *hw) +{ + if (hw->mac.ops.check_for_link) + return hw->mac.ops.check_for_link(hw); + + return -E1000_ERR_CONFIG; +} + +/** + * e1000_check_mng_mode - Check management mode + * @hw: pointer to the HW structure + * + * This checks if the adapter has manageability enabled. + * This is a function pointer entry point called by drivers. + **/ +bool e1000_check_mng_mode(struct e1000_hw *hw) +{ + if (hw->mac.ops.check_mng_mode) + return hw->mac.ops.check_mng_mode(hw); + + return FALSE; +} + +/** + * e1000_mng_write_dhcp_info - Writes DHCP info to host interface + * @hw: pointer to the HW structure + * @buffer: pointer to the host interface + * @length: size of the buffer + * + * Writes the DHCP information to the host interface. + **/ +s32 e1000_mng_write_dhcp_info(struct e1000_hw *hw, u8 *buffer, u16 length) +{ + return e1000_mng_write_dhcp_info_generic(hw, buffer, length); +} + +/** + * e1000_reset_hw - Reset hardware + * @hw: pointer to the HW structure + * + * This resets the hardware into a known state. This is a function pointer + * entry point called by drivers. + **/ +s32 e1000_reset_hw(struct e1000_hw *hw) +{ + if (hw->mac.ops.reset_hw) + return hw->mac.ops.reset_hw(hw); + + return -E1000_ERR_CONFIG; +} + +/** + * e1000_init_hw - Initialize hardware + * @hw: pointer to the HW structure + * + * This inits the hardware readying it for operation. This is a function + * pointer entry point called by drivers. + **/ +s32 e1000_init_hw(struct e1000_hw *hw) +{ + if (hw->mac.ops.init_hw) + return hw->mac.ops.init_hw(hw); + + return -E1000_ERR_CONFIG; +} + +/** + * e1000_setup_link - Configures link and flow control + * @hw: pointer to the HW structure + * + * This configures link and flow control settings for the adapter. This + * is a function pointer entry point called by drivers. While modules can + * also call this, they probably call their own version of this function. + **/ +s32 e1000_setup_link(struct e1000_hw *hw) +{ + if (hw->mac.ops.setup_link) + return hw->mac.ops.setup_link(hw); + + return -E1000_ERR_CONFIG; +} + +/** + * e1000_get_speed_and_duplex - Returns current speed and duplex + * @hw: pointer to the HW structure + * @speed: pointer to a 16-bit value to store the speed + * @duplex: pointer to a 16-bit value to store the duplex. + * + * This returns the speed and duplex of the adapter in the two 'out' + * variables passed in. This is a function pointer entry point called + * by drivers. + **/ +s32 e1000_get_speed_and_duplex(struct e1000_hw *hw, u16 *speed, u16 *duplex) +{ + if (hw->mac.ops.get_link_up_info) + return hw->mac.ops.get_link_up_info(hw, speed, duplex); + + return -E1000_ERR_CONFIG; +} + +/** + * e1000_setup_led - Configures SW controllable LED + * @hw: pointer to the HW structure + * + * This prepares the SW controllable LED for use and saves the current state + * of the LED so it can be later restored. This is a function pointer entry + * point called by drivers. + **/ +s32 e1000_setup_led(struct e1000_hw *hw) +{ + if (hw->mac.ops.setup_led) + return hw->mac.ops.setup_led(hw); + + return E1000_SUCCESS; +} + +/** + * e1000_cleanup_led - Restores SW controllable LED + * @hw: pointer to the HW structure + * + * This restores the SW controllable LED to the value saved off by + * e1000_setup_led. This is a function pointer entry point called by drivers. + **/ +s32 e1000_cleanup_led(struct e1000_hw *hw) +{ + if (hw->mac.ops.cleanup_led) + return hw->mac.ops.cleanup_led(hw); + + return E1000_SUCCESS; +} + +/** + * e1000_blink_led - Blink SW controllable LED + * @hw: pointer to the HW structure + * + * This starts the adapter LED blinking. Request the LED to be setup first + * and cleaned up after. This is a function pointer entry point called by + * drivers. + **/ +s32 e1000_blink_led(struct e1000_hw *hw) +{ + if (hw->mac.ops.blink_led) + return hw->mac.ops.blink_led(hw); + + return E1000_SUCCESS; +} + +/** + * e1000_led_on - Turn on SW controllable LED + * @hw: pointer to the HW structure + * + * Turns the SW defined LED on. This is a function pointer entry point + * called by drivers. + **/ +s32 e1000_led_on(struct e1000_hw *hw) +{ + if (hw->mac.ops.led_on) + return hw->mac.ops.led_on(hw); + + return E1000_SUCCESS; +} + +/** + * e1000_led_off - Turn off SW controllable LED + * @hw: pointer to the HW structure + * + * Turns the SW defined LED off. This is a function pointer entry point + * called by drivers. + **/ +s32 e1000_led_off(struct e1000_hw *hw) +{ + if (hw->mac.ops.led_off) + return hw->mac.ops.led_off(hw); + + return E1000_SUCCESS; +} + +/** + * e1000_reset_adaptive - Reset adaptive IFS + * @hw: pointer to the HW structure + * + * Resets the adaptive IFS. Currently no func pointer exists and all + * implementations are handled in the generic version of this function. + **/ +void e1000_reset_adaptive(struct e1000_hw *hw) +{ + e1000_reset_adaptive_generic(hw); +} + +/** + * e1000_update_adaptive - Update adaptive IFS + * @hw: pointer to the HW structure + * + * Updates adapter IFS. Currently no func pointer exists and all + * implementations are handled in the generic version of this function. + **/ +void e1000_update_adaptive(struct e1000_hw *hw) +{ + e1000_update_adaptive_generic(hw); +} + +/** + * e1000_disable_pcie_master - Disable PCI-Express master access + * @hw: pointer to the HW structure + * + * Disables PCI-Express master access and verifies there are no pending + * requests. Currently no func pointer exists and all implementations are + * handled in the generic version of this function. + **/ +s32 e1000_disable_pcie_master(struct e1000_hw *hw) +{ + return e1000_disable_pcie_master_generic(hw); +} + +/** + * e1000_config_collision_dist - Configure collision distance + * @hw: pointer to the HW structure + * + * Configures the collision distance to the default value and is used + * during link setup. + **/ +void e1000_config_collision_dist(struct e1000_hw *hw) +{ + if (hw->mac.ops.config_collision_dist) + hw->mac.ops.config_collision_dist(hw); +} + +/** + * e1000_rar_set - Sets a receive address register + * @hw: pointer to the HW structure + * @addr: address to set the RAR to + * @index: the RAR to set + * + * Sets a Receive Address Register (RAR) to the specified address. + **/ +void e1000_rar_set(struct e1000_hw *hw, u8 *addr, u32 index) +{ + if (hw->mac.ops.rar_set) + hw->mac.ops.rar_set(hw, addr, index); +} + +/** + * e1000_validate_mdi_setting - Ensures valid MDI/MDIX SW state + * @hw: pointer to the HW structure + * + * Ensures that the MDI/MDIX SW state is valid. + **/ +s32 e1000_validate_mdi_setting(struct e1000_hw *hw) +{ + if (hw->mac.ops.validate_mdi_setting) + return hw->mac.ops.validate_mdi_setting(hw); + + return E1000_SUCCESS; +} + +/** + * e1000_mta_set - Sets multicast table bit + * @hw: pointer to the HW structure + * @hash_value: Multicast hash value. + * + * This sets the bit in the multicast table corresponding to the + * hash value. This is a function pointer entry point called by drivers. + **/ +void e1000_mta_set(struct e1000_hw *hw, u32 hash_value) +{ + if (hw->mac.ops.mta_set) + hw->mac.ops.mta_set(hw, hash_value); +} + +/** + * e1000_hash_mc_addr - Determines address location in multicast table + * @hw: pointer to the HW structure + * @mc_addr: Multicast address to hash. + * + * This hashes an address to determine its location in the multicast + * table. Currently no func pointer exists and all implementations + * are handled in the generic version of this function. + **/ +u32 e1000_hash_mc_addr(struct e1000_hw *hw, u8 *mc_addr) +{ + return e1000_hash_mc_addr_generic(hw, mc_addr); +} + +/** + * e1000_enable_tx_pkt_filtering - Enable packet filtering on TX + * @hw: pointer to the HW structure + * + * Enables packet filtering on transmit packets if manageability is enabled + * and host interface is enabled. + * Currently no func pointer exists and all implementations are handled in the + * generic version of this function. + **/ +bool e1000_enable_tx_pkt_filtering(struct e1000_hw *hw) +{ + return e1000_enable_tx_pkt_filtering_generic(hw); +} + +/** + * e1000_mng_host_if_write - Writes to the manageability host interface + * @hw: pointer to the HW structure + * @buffer: pointer to the host interface buffer + * @length: size of the buffer + * @offset: location in the buffer to write to + * @sum: sum of the data (not checksum) + * + * This function writes the buffer content at the offset given on the host if. + * It also does alignment considerations to do the writes in most efficient + * way. Also fills up the sum of the buffer in *buffer parameter. + **/ +s32 e1000_mng_host_if_write(struct e1000_hw * hw, u8 *buffer, u16 length, + u16 offset, u8 *sum) +{ + if (hw->mac.ops.mng_host_if_write) + return hw->mac.ops.mng_host_if_write(hw, buffer, length, + offset, sum); + + return E1000_NOT_IMPLEMENTED; +} + +/** + * e1000_mng_write_cmd_header - Writes manageability command header + * @hw: pointer to the HW structure + * @hdr: pointer to the host interface command header + * + * Writes the command header after does the checksum calculation. + **/ +s32 e1000_mng_write_cmd_header(struct e1000_hw *hw, + struct e1000_host_mng_command_header *hdr) +{ + if (hw->mac.ops.mng_write_cmd_header) + return hw->mac.ops.mng_write_cmd_header(hw, hdr); + + return E1000_NOT_IMPLEMENTED; +} + +/** + * e1000_mng_enable_host_if - Checks host interface is enabled + * @hw: pointer to the HW structure + * + * Returns E1000_success upon success, else E1000_ERR_HOST_INTERFACE_COMMAND + * + * This function checks whether the HOST IF is enabled for command operation + * and also checks whether the previous command is completed. It busy waits + * in case of previous command is not completed. + **/ +s32 e1000_mng_enable_host_if(struct e1000_hw * hw) +{ + if (hw->mac.ops.mng_enable_host_if) + return hw->mac.ops.mng_enable_host_if(hw); + + return E1000_NOT_IMPLEMENTED; +} + +/** + * e1000_wait_autoneg - Waits for autonegotiation completion + * @hw: pointer to the HW structure + * + * Waits for autoneg to complete. Currently no func pointer exists and all + * implementations are handled in the generic version of this function. + **/ +s32 e1000_wait_autoneg(struct e1000_hw *hw) +{ + if (hw->mac.ops.wait_autoneg) + return hw->mac.ops.wait_autoneg(hw); + + return E1000_SUCCESS; +} + +/** + * e1000_check_reset_block - Verifies PHY can be reset + * @hw: pointer to the HW structure + * + * Checks if the PHY is in a state that can be reset or if manageability + * has it tied up. This is a function pointer entry point called by drivers. + **/ +s32 e1000_check_reset_block(struct e1000_hw *hw) +{ + if (hw->phy.ops.check_reset_block) + return hw->phy.ops.check_reset_block(hw); + + return E1000_SUCCESS; +} + +/** + * e1000_read_phy_reg - Reads PHY register + * @hw: pointer to the HW structure + * @offset: the register to read + * @data: the buffer to store the 16-bit read. + * + * Reads the PHY register and returns the value in data. + * This is a function pointer entry point called by drivers. + **/ +s32 e1000_read_phy_reg(struct e1000_hw *hw, u32 offset, u16 *data) +{ + if (hw->phy.ops.read_reg) + return hw->phy.ops.read_reg(hw, offset, data); + + return E1000_SUCCESS; +} + +/** + * e1000_write_phy_reg - Writes PHY register + * @hw: pointer to the HW structure + * @offset: the register to write + * @data: the value to write. + * + * Writes the PHY register at offset with the value in data. + * This is a function pointer entry point called by drivers. + **/ +s32 e1000_write_phy_reg(struct e1000_hw *hw, u32 offset, u16 data) +{ + if (hw->phy.ops.write_reg) + return hw->phy.ops.write_reg(hw, offset, data); + + return E1000_SUCCESS; +} + +/** + * e1000_release_phy - Generic release PHY + * @hw: pointer to the HW structure + * + * Return if silicon family does not require a semaphore when accessing the + * PHY. + **/ +void e1000_release_phy(struct e1000_hw *hw) +{ + if (hw->phy.ops.release) + hw->phy.ops.release(hw); +} + +/** + * e1000_acquire_phy - Generic acquire PHY + * @hw: pointer to the HW structure + * + * Return success if silicon family does not require a semaphore when + * accessing the PHY. + **/ +s32 e1000_acquire_phy(struct e1000_hw *hw) +{ + if (hw->phy.ops.acquire) + return hw->phy.ops.acquire(hw); + + return E1000_SUCCESS; +} + +/** + * e1000_cfg_on_link_up - Configure PHY upon link up + * @hw: pointer to the HW structure + **/ +s32 e1000_cfg_on_link_up(struct e1000_hw *hw) +{ + if (hw->phy.ops.cfg_on_link_up) + return hw->phy.ops.cfg_on_link_up(hw); + + return E1000_SUCCESS; +} + +/** + * e1000_read_kmrn_reg - Reads register using Kumeran interface + * @hw: pointer to the HW structure + * @offset: the register to read + * @data: the location to store the 16-bit value read. + * + * Reads a register out of the Kumeran interface. Currently no func pointer + * exists and all implementations are handled in the generic version of + * this function. + **/ +s32 e1000_read_kmrn_reg(struct e1000_hw *hw, u32 offset, u16 *data) +{ + return e1000_read_kmrn_reg_generic(hw, offset, data); +} + +/** + * e1000_write_kmrn_reg - Writes register using Kumeran interface + * @hw: pointer to the HW structure + * @offset: the register to write + * @data: the value to write. + * + * Writes a register to the Kumeran interface. Currently no func pointer + * exists and all implementations are handled in the generic version of + * this function. + **/ +s32 e1000_write_kmrn_reg(struct e1000_hw *hw, u32 offset, u16 data) +{ + return e1000_write_kmrn_reg_generic(hw, offset, data); +} + +/** + * e1000_get_cable_length - Retrieves cable length estimation + * @hw: pointer to the HW structure + * + * This function estimates the cable length and stores them in + * hw->phy.min_length and hw->phy.max_length. This is a function pointer + * entry point called by drivers. + **/ +s32 e1000_get_cable_length(struct e1000_hw *hw) +{ + if (hw->phy.ops.get_cable_length) + return hw->phy.ops.get_cable_length(hw); + + return E1000_SUCCESS; +} + +/** + * e1000_get_phy_info - Retrieves PHY information from registers + * @hw: pointer to the HW structure + * + * This function gets some information from various PHY registers and + * populates hw->phy values with it. This is a function pointer entry + * point called by drivers. + **/ +s32 e1000_get_phy_info(struct e1000_hw *hw) +{ + if (hw->phy.ops.get_info) + return hw->phy.ops.get_info(hw); + + return E1000_SUCCESS; +} + +/** + * e1000_phy_hw_reset - Hard PHY reset + * @hw: pointer to the HW structure + * + * Performs a hard PHY reset. This is a function pointer entry point called + * by drivers. + **/ +s32 e1000_phy_hw_reset(struct e1000_hw *hw) +{ + if (hw->phy.ops.reset) + return hw->phy.ops.reset(hw); + + return E1000_SUCCESS; +} + +/** + * e1000_phy_commit - Soft PHY reset + * @hw: pointer to the HW structure + * + * Performs a soft PHY reset on those that apply. This is a function pointer + * entry point called by drivers. + **/ +s32 e1000_phy_commit(struct e1000_hw *hw) +{ + if (hw->phy.ops.commit) + return hw->phy.ops.commit(hw); + + return E1000_SUCCESS; +} + +/** + * e1000_set_d0_lplu_state - Sets low power link up state for D0 + * @hw: pointer to the HW structure + * @active: boolean used to enable/disable lplu + * + * Success returns 0, Failure returns 1 + * + * The low power link up (lplu) state is set to the power management level D0 + * and SmartSpeed is disabled when active is TRUE, else clear lplu for D0 + * and enable Smartspeed. LPLU and Smartspeed are mutually exclusive. LPLU + * is used during Dx states where the power conservation is most important. + * During driver activity, SmartSpeed should be enabled so performance is + * maintained. This is a function pointer entry point called by drivers. + **/ +s32 e1000_set_d0_lplu_state(struct e1000_hw *hw, bool active) +{ + if (hw->phy.ops.set_d0_lplu_state) + return hw->phy.ops.set_d0_lplu_state(hw, active); + + return E1000_SUCCESS; +} + +/** + * e1000_set_d3_lplu_state - Sets low power link up state for D3 + * @hw: pointer to the HW structure + * @active: boolean used to enable/disable lplu + * + * Success returns 0, Failure returns 1 + * + * The low power link up (lplu) state is set to the power management level D3 + * and SmartSpeed is disabled when active is TRUE, else clear lplu for D3 + * and enable Smartspeed. LPLU and Smartspeed are mutually exclusive. LPLU + * is used during Dx states where the power conservation is most important. + * During driver activity, SmartSpeed should be enabled so performance is + * maintained. This is a function pointer entry point called by drivers. + **/ +s32 e1000_set_d3_lplu_state(struct e1000_hw *hw, bool active) +{ + if (hw->phy.ops.set_d3_lplu_state) + return hw->phy.ops.set_d3_lplu_state(hw, active); + + return E1000_SUCCESS; +} + +/** + * e1000_read_mac_addr - Reads MAC address + * @hw: pointer to the HW structure + * + * Reads the MAC address out of the adapter and stores it in the HW structure. + * Currently no func pointer exists and all implementations are handled in the + * generic version of this function. + **/ +s32 e1000_read_mac_addr(struct e1000_hw *hw) +{ + if (hw->mac.ops.read_mac_addr) + return hw->mac.ops.read_mac_addr(hw); + + return e1000_read_mac_addr_generic(hw); +} + +/** + * e1000_read_pba_num - Read device part number + * @hw: pointer to the HW structure + * @pba_num: pointer to device part number + * + * Reads the product board assembly (PBA) number from the EEPROM and stores + * the value in pba_num. + * Currently no func pointer exists and all implementations are handled in the + * generic version of this function. + **/ +s32 e1000_read_pba_num(struct e1000_hw *hw, u32 *pba_num) +{ + return e1000_read_pba_num_generic(hw, pba_num); +} + +/** + * e1000_validate_nvm_checksum - Verifies NVM (EEPROM) checksum + * @hw: pointer to the HW structure + * + * Validates the NVM checksum is correct. This is a function pointer entry + * point called by drivers. + **/ +s32 e1000_validate_nvm_checksum(struct e1000_hw *hw) +{ + if (hw->nvm.ops.validate) + return hw->nvm.ops.validate(hw); + + return -E1000_ERR_CONFIG; +} + +/** + * e1000_update_nvm_checksum - Updates NVM (EEPROM) checksum + * @hw: pointer to the HW structure + * + * Updates the NVM checksum. Currently no func pointer exists and all + * implementations are handled in the generic version of this function. + **/ +s32 e1000_update_nvm_checksum(struct e1000_hw *hw) +{ + if (hw->nvm.ops.update) + return hw->nvm.ops.update(hw); + + return -E1000_ERR_CONFIG; +} + +/** + * e1000_reload_nvm - Reloads EEPROM + * @hw: pointer to the HW structure + * + * Reloads the EEPROM by setting the "Reinitialize from EEPROM" bit in the + * extended control register. + **/ +void e1000_reload_nvm(struct e1000_hw *hw) +{ + if (hw->nvm.ops.reload) + hw->nvm.ops.reload(hw); +} + +/** + * e1000_read_nvm - Reads NVM (EEPROM) + * @hw: pointer to the HW structure + * @offset: the word offset to read + * @words: number of 16-bit words to read + * @data: pointer to the properly sized buffer for the data. + * + * Reads 16-bit chunks of data from the NVM (EEPROM). This is a function + * pointer entry point called by drivers. + **/ +s32 e1000_read_nvm(struct e1000_hw *hw, u16 offset, u16 words, u16 *data) +{ + if (hw->nvm.ops.read) + return hw->nvm.ops.read(hw, offset, words, data); + + return -E1000_ERR_CONFIG; +} + +/** + * e1000_write_nvm - Writes to NVM (EEPROM) + * @hw: pointer to the HW structure + * @offset: the word offset to read + * @words: number of 16-bit words to write + * @data: pointer to the properly sized buffer for the data. + * + * Writes 16-bit chunks of data to the NVM (EEPROM). This is a function + * pointer entry point called by drivers. + **/ +s32 e1000_write_nvm(struct e1000_hw *hw, u16 offset, u16 words, u16 *data) +{ + if (hw->nvm.ops.write) + return hw->nvm.ops.write(hw, offset, words, data); + + return E1000_SUCCESS; +} + +/** + * e1000_write_8bit_ctrl_reg - Writes 8bit Control register + * @hw: pointer to the HW structure + * @reg: 32bit register offset + * @offset: the register to write + * @data: the value to write. + * + * Writes the PHY register at offset with the value in data. + * This is a function pointer entry point called by drivers. + **/ +s32 e1000_write_8bit_ctrl_reg(struct e1000_hw *hw, u32 reg, u32 offset, + u8 data) +{ + return e1000_write_8bit_ctrl_reg_generic(hw, reg, offset, data); +} + +/** + * e1000_power_up_phy - Restores link in case of PHY power down + * @hw: pointer to the HW structure + * + * The phy may be powered down to save power, to turn off link when the + * driver is unloaded, or wake on lan is not enabled (among others). + **/ +void e1000_power_up_phy(struct e1000_hw *hw) +{ + if (hw->phy.ops.power_up) + hw->phy.ops.power_up(hw); + + e1000_setup_link(hw); +} + +/** + * e1000_power_down_phy - Power down PHY + * @hw: pointer to the HW structure + * + * The phy may be powered down to save power, to turn off link when the + * driver is unloaded, or wake on lan is not enabled (among others). + **/ +void e1000_power_down_phy(struct e1000_hw *hw) +{ + if (hw->phy.ops.power_down) + hw->phy.ops.power_down(hw); +} + +/** + * e1000_shutdown_fiber_serdes_link - Remove link during power down + * @hw: pointer to the HW structure + * + * Shutdown the optics and PCS on driver unload. + **/ +void e1000_shutdown_fiber_serdes_link(struct e1000_hw *hw) +{ + if (hw->mac.ops.shutdown_serdes) + hw->mac.ops.shutdown_serdes(hw); +} + diff --git a/sys/dev/netif/ig_hal/e1000_api.h b/sys/dev/netif/ig_hal/e1000_api.h new file mode 100644 index 0000000000..4629ff074e --- /dev/null +++ b/sys/dev/netif/ig_hal/e1000_api.h @@ -0,0 +1,162 @@ +/****************************************************************************** + + Copyright (c) 2001-2008, Intel Corporation + All rights reserved. + + Redistribution and use in source and binary forms, with or without + modification, are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, + this list of conditions and the following disclaimer. + + 2. Redistributions in binary form must reproduce the above copyright + notice, this list of conditions and the following disclaimer in the + documentation and/or other materials provided with the distribution. + + 3. Neither the name of the Intel Corporation nor the names of its + contributors may be used to endorse or promote products derived from + this software without specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE + ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE + LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR + CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF + SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS + INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN + CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) + ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + POSSIBILITY OF SUCH DAMAGE. + +******************************************************************************/ +/*$FreeBSD$*/ + +#ifndef _E1000_API_H_ +#define _E1000_API_H_ + +#include "e1000_hw.h" + +extern void e1000_init_function_pointers_82542(struct e1000_hw *hw); +extern void e1000_init_function_pointers_82543(struct e1000_hw *hw); +extern void e1000_init_function_pointers_82540(struct e1000_hw *hw); +extern void e1000_init_function_pointers_82571(struct e1000_hw *hw); +extern void e1000_init_function_pointers_82541(struct e1000_hw *hw); +extern void e1000_init_function_pointers_80003es2lan(struct e1000_hw *hw); +extern void e1000_init_function_pointers_ich8lan(struct e1000_hw *hw); +extern void e1000_init_function_pointers_82575(struct e1000_hw *hw); +extern void e1000_rx_fifo_flush_82575(struct e1000_hw *hw); +extern void e1000_init_function_pointers_vf(struct e1000_hw *hw); +extern void e1000_shutdown_fiber_serdes_link(struct e1000_hw *hw); + +s32 e1000_set_mac_type(struct e1000_hw *hw); +s32 e1000_setup_init_funcs(struct e1000_hw *hw, bool init_device); +s32 e1000_init_mac_params(struct e1000_hw *hw); +s32 e1000_init_nvm_params(struct e1000_hw *hw); +s32 e1000_init_phy_params(struct e1000_hw *hw); +s32 e1000_get_bus_info(struct e1000_hw *hw); +void e1000_clear_vfta(struct e1000_hw *hw); +void e1000_write_vfta(struct e1000_hw *hw, u32 offset, u32 value); +s32 e1000_force_mac_fc(struct e1000_hw *hw); +s32 e1000_check_for_link(struct e1000_hw *hw); +s32 e1000_reset_hw(struct e1000_hw *hw); +s32 e1000_init_hw(struct e1000_hw *hw); +s32 e1000_setup_link(struct e1000_hw *hw); +s32 e1000_get_speed_and_duplex(struct e1000_hw *hw, u16 *speed, + u16 *duplex); +s32 e1000_disable_pcie_master(struct e1000_hw *hw); +void e1000_config_collision_dist(struct e1000_hw *hw); +void e1000_rar_set(struct e1000_hw *hw, u8 *addr, u32 index); +void e1000_mta_set(struct e1000_hw *hw, u32 hash_value); +u32 e1000_hash_mc_addr(struct e1000_hw *hw, u8 *mc_addr); +void e1000_update_mc_addr_list(struct e1000_hw *hw, + u8 *mc_addr_list, u32 mc_addr_count, + u32 rar_used_count, u32 rar_count); +s32 e1000_setup_led(struct e1000_hw *hw); +s32 e1000_cleanup_led(struct e1000_hw *hw); +s32 e1000_check_reset_block(struct e1000_hw *hw); +s32 e1000_blink_led(struct e1000_hw *hw); +s32 e1000_led_on(struct e1000_hw *hw); +s32 e1000_led_off(struct e1000_hw *hw); +void e1000_reset_adaptive(struct e1000_hw *hw); +void e1000_update_adaptive(struct e1000_hw *hw); +s32 e1000_get_cable_length(struct e1000_hw *hw); +s32 e1000_validate_mdi_setting(struct e1000_hw *hw); +s32 e1000_read_phy_reg(struct e1000_hw *hw, u32 offset, u16 *data); +s32 e1000_write_phy_reg(struct e1000_hw *hw, u32 offset, u16 data); +s32 e1000_write_8bit_ctrl_reg(struct e1000_hw *hw, u32 reg, + u32 offset, u8 data); +s32 e1000_get_phy_info(struct e1000_hw *hw); +void e1000_release_phy(struct e1000_hw *hw); +s32 e1000_acquire_phy(struct e1000_hw *hw); +s32 e1000_cfg_on_link_up(struct e1000_hw *hw); +s32 e1000_phy_hw_reset(struct e1000_hw *hw); +s32 e1000_phy_commit(struct e1000_hw *hw); +void e1000_power_up_phy(struct e1000_hw *hw); +void e1000_power_down_phy(struct e1000_hw *hw); +s32 e1000_read_mac_addr(struct e1000_hw *hw); +s32 e1000_read_pba_num(struct e1000_hw *hw, u32 *part_num); +void e1000_reload_nvm(struct e1000_hw *hw); +s32 e1000_update_nvm_checksum(struct e1000_hw *hw); +s32 e1000_validate_nvm_checksum(struct e1000_hw *hw); +s32 e1000_read_nvm(struct e1000_hw *hw, u16 offset, u16 words, u16 *data); +s32 e1000_read_kmrn_reg(struct e1000_hw *hw, u32 offset, u16 *data); +s32 e1000_write_kmrn_reg(struct e1000_hw *hw, u32 offset, u16 data); +s32 e1000_write_nvm(struct e1000_hw *hw, u16 offset, u16 words, + u16 *data); +s32 e1000_wait_autoneg(struct e1000_hw *hw); +s32 e1000_set_d3_lplu_state(struct e1000_hw *hw, bool active); +s32 e1000_set_d0_lplu_state(struct e1000_hw *hw, bool active); +bool e1000_check_mng_mode(struct e1000_hw *hw); +bool e1000_enable_tx_pkt_filtering(struct e1000_hw *hw); +s32 e1000_mng_enable_host_if(struct e1000_hw *hw); +s32 e1000_mng_host_if_write(struct e1000_hw *hw, + u8 *buffer, u16 length, u16 offset, u8 *sum); +s32 e1000_mng_write_cmd_header(struct e1000_hw *hw, + struct e1000_host_mng_command_header *hdr); +s32 e1000_mng_write_dhcp_info(struct e1000_hw * hw, + u8 *buffer, u16 length); +u32 e1000_translate_register_82542(u32 reg); + +/* + * TBI_ACCEPT macro definition: + * + * This macro requires: + * adapter = a pointer to struct e1000_hw + * status = the 8 bit status field of the Rx descriptor with EOP set + * error = the 8 bit error field of the Rx descriptor with EOP set + * length = the sum of all the length fields of the Rx descriptors that + * make up the current frame + * last_byte = the last byte of the frame DMAed by the hardware + * max_frame_length = the maximum frame length we want to accept. + * min_frame_length = the minimum frame length we want to accept. + * + * This macro is a conditional that should be used in the interrupt + * handler's Rx processing routine when RxErrors have been detected. + * + * Typical use: + * ... + * if (TBI_ACCEPT) { + * accept_frame = TRUE; + * e1000_tbi_adjust_stats(adapter, MacAddress); + * frame_length--; + * } else { + * accept_frame = FALSE; + * } + * ... + */ + +/* The carrier extension symbol, as received by the NIC. */ +#define CARRIER_EXTENSION 0x0F + +#define TBI_ACCEPT(a, status, errors, length, last_byte, min_frame_size, max_frame_size) \ + (e1000_tbi_sbp_enabled_82543(a) && \ + (((errors) & E1000_RXD_ERR_FRAME_ERR_MASK) == E1000_RXD_ERR_CE) && \ + ((last_byte) == CARRIER_EXTENSION) && \ + (((status) & E1000_RXD_STAT_VP) ? \ + (((length) > (min_frame_size - VLAN_TAG_SIZE)) && \ + ((length) <= (max_frame_size + 1))) : \ + (((length) > min_frame_size) && \ + ((length) <= (max_frame_size + VLAN_TAG_SIZE + 1))))) + +#endif diff --git a/sys/dev/netif/ig_hal/e1000_defines.h b/sys/dev/netif/ig_hal/e1000_defines.h new file mode 100644 index 0000000000..81259a1275 --- /dev/null +++ b/sys/dev/netif/ig_hal/e1000_defines.h @@ -0,0 +1,1519 @@ +/****************************************************************************** + + Copyright (c) 2001-2008, Intel Corporation + All rights reserved. + + Redistribution and use in source and binary forms, with or without + modification, are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, + this list of conditions and the following disclaimer. + + 2. Redistributions in binary form must reproduce the above copyright + notice, this list of conditions and the following disclaimer in the + documentation and/or other materials provided with the distribution. + + 3. Neither the name of the Intel Corporation nor the names of its + contributors may be used to endorse or promote products derived from + this software without specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE + ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE + LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR + CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF + SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS + INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN + CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) + ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + POSSIBILITY OF SUCH DAMAGE. + +******************************************************************************/ +/*$FreeBSD$*/ + +#ifndef _E1000_DEFINES_H_ +#define _E1000_DEFINES_H_ + +/* Number of Transmit and Receive Descriptors must be a multiple of 8 */ +#define REQ_TX_DESCRIPTOR_MULTIPLE 8 +#define REQ_RX_DESCRIPTOR_MULTIPLE 8 + +/* Definitions for power management and wakeup registers */ +/* Wake Up Control */ +#define E1000_WUC_APME 0x00000001 /* APM Enable */ +#define E1000_WUC_PME_EN 0x00000002 /* PME Enable */ +#define E1000_WUC_PME_STATUS 0x00000004 /* PME Status */ +#define E1000_WUC_APMPME 0x00000008 /* Assert PME on APM Wakeup */ +#define E1000_WUC_LSCWE 0x00000010 /* Link Status wake up enable */ +#define E1000_WUC_LSCWO 0x00000020 /* Link Status wake up override */ +#define E1000_WUC_SPM 0x80000000 /* Enable SPM */ +#define E1000_WUC_PHY_WAKE 0x00000100 /* if PHY supports wakeup */ + +/* Wake Up Filter Control */ +#define E1000_WUFC_LNKC 0x00000001 /* Link Status Change Wakeup Enable */ +#define E1000_WUFC_MAG 0x00000002 /* Magic Packet Wakeup Enable */ +#define E1000_WUFC_EX 0x00000004 /* Directed Exact Wakeup Enable */ +#define E1000_WUFC_MC 0x00000008 /* Directed Multicast Wakeup Enable */ +#define E1000_WUFC_BC 0x00000010 /* Broadcast Wakeup Enable */ +#define E1000_WUFC_ARP 0x00000020 /* ARP Request Packet Wakeup Enable */ +#define E1000_WUFC_IPV4 0x00000040 /* Directed IPv4 Packet Wakeup Enable */ +#define E1000_WUFC_IPV6 0x00000080 /* Directed IPv6 Packet Wakeup Enable */ +#define E1000_WUFC_IGNORE_TCO_PHY 0x00000800 /* Ignore WakeOn TCO packets */ +#define E1000_WUFC_FLX0_PHY 0x00001000 /* Flexible Filter 0 Enable */ +#define E1000_WUFC_FLX1_PHY 0x00002000 /* Flexible Filter 1 Enable */ +#define E1000_WUFC_FLX2_PHY 0x00004000 /* Flexible Filter 2 Enable */ +#define E1000_WUFC_FLX3_PHY 0x00008000 /* Flexible Filter 3 Enable */ +#define E1000_WUFC_IGNORE_TCO 0x00008000 /* Ignore WakeOn TCO packets */ +#define E1000_WUFC_FLX0 0x00010000 /* Flexible Filter 0 Enable */ +#define E1000_WUFC_FLX1 0x00020000 /* Flexible Filter 1 Enable */ +#define E1000_WUFC_FLX2 0x00040000 /* Flexible Filter 2 Enable */ +#define E1000_WUFC_FLX3 0x00080000 /* Flexible Filter 3 Enable */ +#define E1000_WUFC_FLX4 0x00100000 /* Flexible Filter 4 Enable */ +#define E1000_WUFC_FLX5 0x00200000 /* Flexible Filter 5 Enable */ +#define E1000_WUFC_ALL_FILTERS_PHY_4 0x0000F0FF /*Mask for all wakeup filters*/ +#define E1000_WUFC_FLX_OFFSET_PHY 12 /* Offset to the Flexible Filters bits */ +#define E1000_WUFC_FLX_FILTERS_PHY_4 0x0000F000 /*Mask for 4 flexible filters*/ +#define E1000_WUFC_ALL_FILTERS 0x000F00FF /* Mask for all wakeup filters */ +#define E1000_WUFC_FLX_OFFSET 16 /* Offset to the Flexible Filters bits */ +#define E1000_WUFC_FLX_FILTERS 0x000F0000 /*Mask for the 4 flexible filters */ +/* + * For 82576 to utilize Extended filter masks in addition to + * existing (filter) masks + */ +#define E1000_WUFC_EXT_FLX_FILTERS 0x00300000 /* Ext. FLX filter mask */ + +/* Wake Up Status */ +#define E1000_WUS_LNKC E1000_WUFC_LNKC +#define E1000_WUS_MAG E1000_WUFC_MAG +#define E1000_WUS_EX E1000_WUFC_EX +#define E1000_WUS_MC E1000_WUFC_MC +#define E1000_WUS_BC E1000_WUFC_BC +#define E1000_WUS_ARP E1000_WUFC_ARP +#define E1000_WUS_IPV4 E1000_WUFC_IPV4 +#define E1000_WUS_IPV6 E1000_WUFC_IPV6 +#define E1000_WUS_FLX0_PHY E1000_WUFC_FLX0_PHY +#define E1000_WUS_FLX1_PHY E1000_WUFC_FLX1_PHY +#define E1000_WUS_FLX2_PHY E1000_WUFC_FLX2_PHY +#define E1000_WUS_FLX3_PHY E1000_WUFC_FLX3_PHY +#define E1000_WUS_FLX_FILTERS_PHY_4 E1000_WUFC_FLX_FILTERS_PHY_4 +#define E1000_WUS_FLX0 E1000_WUFC_FLX0 +#define E1000_WUS_FLX1 E1000_WUFC_FLX1 +#define E1000_WUS_FLX2 E1000_WUFC_FLX2 +#define E1000_WUS_FLX3 E1000_WUFC_FLX3 +#define E1000_WUS_FLX_FILTERS E1000_WUFC_FLX_FILTERS + +/* Wake Up Packet Length */ +#define E1000_WUPL_LENGTH_MASK 0x0FFF /* Only the lower 12 bits are valid */ + +/* Four Flexible Filters are supported */ +#define E1000_FLEXIBLE_FILTER_COUNT_MAX 4 +/* Two Extended Flexible Filters are supported (82576) */ +#define E1000_EXT_FLEXIBLE_FILTER_COUNT_MAX 2 +#define E1000_FHFT_LENGTH_OFFSET 0xFC /* Length byte in FHFT */ +#define E1000_FHFT_LENGTH_MASK 0x0FF /* Length in lower byte */ + +/* Each Flexible Filter is at most 128 (0x80) bytes in length */ +#define E1000_FLEXIBLE_FILTER_SIZE_MAX 128 + +#define E1000_FFLT_SIZE E1000_FLEXIBLE_FILTER_COUNT_MAX +#define E1000_FFMT_SIZE E1000_FLEXIBLE_FILTER_SIZE_MAX +#define E1000_FFVT_SIZE E1000_FLEXIBLE_FILTER_SIZE_MAX + +/* Extended Device Control */ +#define E1000_CTRL_EXT_GPI0_EN 0x00000001 /* Maps SDP4 to GPI0 */ +#define E1000_CTRL_EXT_GPI1_EN 0x00000002 /* Maps SDP5 to GPI1 */ +#define E1000_CTRL_EXT_PHYINT_EN E1000_CTRL_EXT_GPI1_EN +#define E1000_CTRL_EXT_GPI2_EN 0x00000004 /* Maps SDP6 to GPI2 */ +#define E1000_CTRL_EXT_GPI3_EN 0x00000008 /* Maps SDP7 to GPI3 */ +/* Reserved (bits 4,5) in >= 82575 */ +#define E1000_CTRL_EXT_SDP4_DATA 0x00000010 /* Value of SW Definable Pin 4 */ +#define E1000_CTRL_EXT_SDP5_DATA 0x00000020 /* Value of SW Definable Pin 5 */ +#define E1000_CTRL_EXT_PHY_INT E1000_CTRL_EXT_SDP5_DATA +#define E1000_CTRL_EXT_SDP6_DATA 0x00000040 /* Value of SW Definable Pin 6 */ +#define E1000_CTRL_EXT_SDP7_DATA 0x00000080 /* Value of SW Definable Pin 7 */ +/* SDP 4/5 (bits 8,9) are reserved in >= 82575 */ +#define E1000_CTRL_EXT_SDP4_DIR 0x00000100 /* Direction of SDP4 0=in 1=out */ +#define E1000_CTRL_EXT_SDP5_DIR 0x00000200 /* Direction of SDP5 0=in 1=out */ +#define E1000_CTRL_EXT_SDP6_DIR 0x00000400 /* Direction of SDP6 0=in 1=out */ +#define E1000_CTRL_EXT_SDP7_DIR 0x00000800 /* Direction of SDP7 0=in 1=out */ +#define E1000_CTRL_EXT_ASDCHK 0x00001000 /* Initiate an ASD sequence */ +#define E1000_CTRL_EXT_EE_RST 0x00002000 /* Reinitialize from EEPROM */ +#define E1000_CTRL_EXT_IPS 0x00004000 /* Invert Power State */ +/* Physical Func Reset Done Indication */ +#define E1000_CTRL_EXT_PFRSTD 0x00004000 +#define E1000_CTRL_EXT_SPD_BYPS 0x00008000 /* Speed Select Bypass */ +#define E1000_CTRL_EXT_RO_DIS 0x00020000 /* Relaxed Ordering disable */ +#define E1000_CTRL_EXT_LINK_MODE_MASK 0x00C00000 +#define E1000_CTRL_EXT_LINK_MODE_GMII 0x00000000 +#define E1000_CTRL_EXT_LINK_MODE_TBI 0x00C00000 +#define E1000_CTRL_EXT_LINK_MODE_KMRN 0x00000000 +#define E1000_CTRL_EXT_LINK_MODE_PCIE_SERDES 0x00C00000 +#define E1000_CTRL_EXT_LINK_MODE_PCIX_SERDES 0x00800000 +#define E1000_CTRL_EXT_LINK_MODE_SGMII 0x00800000 +#define E1000_CTRL_EXT_EIAME 0x01000000 +#define E1000_CTRL_EXT_IRCA 0x00000001 +#define E1000_CTRL_EXT_WR_WMARK_MASK 0x03000000 +#define E1000_CTRL_EXT_WR_WMARK_256 0x00000000 +#define E1000_CTRL_EXT_WR_WMARK_320 0x01000000 +#define E1000_CTRL_EXT_WR_WMARK_384 0x02000000 +#define E1000_CTRL_EXT_WR_WMARK_448 0x03000000 +#define E1000_CTRL_EXT_CANC 0x04000000 /* Int delay cancellation */ +#define E1000_CTRL_EXT_DRV_LOAD 0x10000000 /* Driver loaded bit for FW */ +/* IAME enable bit (27) was removed in >= 82575 */ +#define E1000_CTRL_EXT_IAME 0x08000000 /* Int acknowledge Auto-mask */ +#define E1000_CTRL_EXT_INT_TIMER_CLR 0x20000000 /* Clear Interrupt timers + * after IMS clear */ +#define E1000_CRTL_EXT_PB_PAREN 0x01000000 /* packet buffer parity error + * detection enabled */ +#define E1000_CTRL_EXT_DF_PAREN 0x02000000 /* descriptor FIFO parity + * error detection enable */ +#define E1000_CTRL_EXT_GHOST_PAREN 0x40000000 +#define E1000_CTRL_EXT_PBA_CLR 0x80000000 /* PBA Clear */ +#define E1000_CTRL_EXT_LSECCK 0x00001000 +#define E1000_I2CCMD_REG_ADDR_SHIFT 16 +#define E1000_I2CCMD_REG_ADDR 0x00FF0000 +#define E1000_I2CCMD_PHY_ADDR_SHIFT 24 +#define E1000_I2CCMD_PHY_ADDR 0x07000000 +#define E1000_I2CCMD_OPCODE_READ 0x08000000 +#define E1000_I2CCMD_OPCODE_WRITE 0x00000000 +#define E1000_I2CCMD_RESET 0x10000000 +#define E1000_I2CCMD_READY 0x20000000 +#define E1000_I2CCMD_INTERRUPT_ENA 0x40000000 +#define E1000_I2CCMD_ERROR 0x80000000 +#define E1000_MAX_SGMII_PHY_REG_ADDR 255 +#define E1000_I2CCMD_PHY_TIMEOUT 200 +#define E1000_IVAR_VALID 0x80 +#define E1000_GPIE_NSICR 0x00000001 +#define E1000_GPIE_MSIX_MODE 0x00000010 +#define E1000_GPIE_EIAME 0x40000000 +#define E1000_GPIE_PBA 0x80000000 + +/* Receive Descriptor bit definitions */ +#define E1000_RXD_STAT_DD 0x01 /* Descriptor Done */ +#define E1000_RXD_STAT_EOP 0x02 /* End of Packet */ +#define E1000_RXD_STAT_IXSM 0x04 /* Ignore checksum */ +#define E1000_RXD_STAT_VP 0x08 /* IEEE VLAN Packet */ +#define E1000_RXD_STAT_UDPCS 0x10 /* UDP xsum calculated */ +#define E1000_RXD_STAT_TCPCS 0x20 /* TCP xsum calculated */ +#define E1000_RXD_STAT_IPCS 0x40 /* IP xsum calculated */ +#define E1000_RXD_STAT_PIF 0x80 /* passed in-exact filter */ +#define E1000_RXD_STAT_CRCV 0x100 /* Speculative CRC Valid */ +#define E1000_RXD_STAT_IPIDV 0x200 /* IP identification valid */ +#define E1000_RXD_STAT_UDPV 0x400 /* Valid UDP checksum */ +#define E1000_RXD_STAT_DYNINT 0x800 /* Pkt caused INT via DYNINT */ +#define E1000_RXD_STAT_ACK 0x8000 /* ACK Packet indication */ +#define E1000_RXD_ERR_CE 0x01 /* CRC Error */ +#define E1000_RXD_ERR_SE 0x02 /* Symbol Error */ +#define E1000_RXD_ERR_SEQ 0x04 /* Sequence Error */ +#define E1000_RXD_ERR_CXE 0x10 /* Carrier Extension Error */ +#define E1000_RXD_ERR_TCPE 0x20 /* TCP/UDP Checksum Error */ +#define E1000_RXD_ERR_IPE 0x40 /* IP Checksum Error */ +#define E1000_RXD_ERR_RXE 0x80 /* Rx Data Error */ +#define E1000_RXD_SPC_VLAN_MASK 0x0FFF /* VLAN ID is in lower 12 bits */ +#define E1000_RXD_SPC_PRI_MASK 0xE000 /* Priority is in upper 3 bits */ +#define E1000_RXD_SPC_PRI_SHIFT 13 +#define E1000_RXD_SPC_CFI_MASK 0x1000 /* CFI is bit 12 */ +#define E1000_RXD_SPC_CFI_SHIFT 12 + +#define E1000_RXDEXT_STATERR_CE 0x01000000 +#define E1000_RXDEXT_STATERR_SE 0x02000000 +#define E1000_RXDEXT_STATERR_SEQ 0x04000000 +#define E1000_RXDEXT_STATERR_CXE 0x10000000 +#define E1000_RXDEXT_STATERR_TCPE 0x20000000 +#define E1000_RXDEXT_STATERR_IPE 0x40000000 +#define E1000_RXDEXT_STATERR_RXE 0x80000000 + +#define E1000_RXDEXT_LSECH 0x01000000 +#define E1000_RXDEXT_LSECE_MASK 0x60000000 +#define E1000_RXDEXT_LSECE_NO_ERROR 0x00000000 +#define E1000_RXDEXT_LSECE_NO_SA_MATCH 0x20000000 +#define E1000_RXDEXT_LSECE_REPLAY_DETECT 0x40000000 +#define E1000_RXDEXT_LSECE_BAD_SIG 0x60000000 + +/* mask to determine if packets should be dropped due to frame errors */ +#define E1000_RXD_ERR_FRAME_ERR_MASK ( \ + E1000_RXD_ERR_CE | \ + E1000_RXD_ERR_SE | \ + E1000_RXD_ERR_SEQ | \ + E1000_RXD_ERR_CXE | \ + E1000_RXD_ERR_RXE) + +/* Same mask, but for extended and packet split descriptors */ +#define E1000_RXDEXT_ERR_FRAME_ERR_MASK ( \ + E1000_RXDEXT_STATERR_CE | \ + E1000_RXDEXT_STATERR_SE | \ + E1000_RXDEXT_STATERR_SEQ | \ + E1000_RXDEXT_STATERR_CXE | \ + E1000_RXDEXT_STATERR_RXE) + +#define E1000_MRQC_ENABLE_MASK 0x00000007 +#define E1000_MRQC_ENABLE_RSS_2Q 0x00000001 +#define E1000_MRQC_ENABLE_RSS_INT 0x00000004 +#define E1000_MRQC_RSS_FIELD_MASK 0xFFFF0000 +#define E1000_MRQC_RSS_FIELD_IPV4_TCP 0x00010000 +#define E1000_MRQC_RSS_FIELD_IPV4 0x00020000 +#define E1000_MRQC_RSS_FIELD_IPV6_TCP_EX 0x00040000 +#define E1000_MRQC_RSS_FIELD_IPV6_EX 0x00080000 +#define E1000_MRQC_RSS_FIELD_IPV6 0x00100000 +#define E1000_MRQC_RSS_FIELD_IPV6_TCP 0x00200000 + +#define E1000_RXDPS_HDRSTAT_HDRSP 0x00008000 +#define E1000_RXDPS_HDRSTAT_HDRLEN_MASK 0x000003FF + +/* Management Control */ +#define E1000_MANC_SMBUS_EN 0x00000001 /* SMBus Enabled - RO */ +#define E1000_MANC_ASF_EN 0x00000002 /* ASF Enabled - RO */ +#define E1000_MANC_R_ON_FORCE 0x00000004 /* Reset on Force TCO - RO */ +#define E1000_MANC_RMCP_EN 0x00000100 /* Enable RCMP 026Fh Filtering */ +#define E1000_MANC_0298_EN 0x00000200 /* Enable RCMP 0298h Filtering */ +#define E1000_MANC_IPV4_EN 0x00000400 /* Enable IPv4 */ +#define E1000_MANC_IPV6_EN 0x00000800 /* Enable IPv6 */ +#define E1000_MANC_SNAP_EN 0x00001000 /* Accept LLC/SNAP */ +#define E1000_MANC_ARP_EN 0x00002000 /* Enable ARP Request Filtering */ +/* Enable Neighbor Discovery Filtering */ +#define E1000_MANC_NEIGHBOR_EN 0x00004000 +#define E1000_MANC_ARP_RES_EN 0x00008000 /* Enable ARP response Filtering */ +#define E1000_MANC_TCO_RESET 0x00010000 /* TCO Reset Occurred */ +#define E1000_MANC_RCV_TCO_EN 0x00020000 /* Receive TCO Packets Enabled */ +#define E1000_MANC_REPORT_STATUS 0x00040000 /* Status Reporting Enabled */ +#define E1000_MANC_RCV_ALL 0x00080000 /* Receive All Enabled */ +#define E1000_MANC_BLK_PHY_RST_ON_IDE 0x00040000 /* Block phy resets */ +/* Enable MAC address filtering */ +#define E1000_MANC_EN_MAC_ADDR_FILTER 0x00100000 +/* Enable MNG packets to host memory */ +#define E1000_MANC_EN_MNG2HOST 0x00200000 +/* Enable IP address filtering */ +#define E1000_MANC_EN_IP_ADDR_FILTER 0x00400000 +#define E1000_MANC_EN_XSUM_FILTER 0x00800000 /* Enable checksum filtering */ +#define E1000_MANC_BR_EN 0x01000000 /* Enable broadcast filtering */ +#define E1000_MANC_SMB_REQ 0x01000000 /* SMBus Request */ +#define E1000_MANC_SMB_GNT 0x02000000 /* SMBus Grant */ +#define E1000_MANC_SMB_CLK_IN 0x04000000 /* SMBus Clock In */ +#define E1000_MANC_SMB_DATA_IN 0x08000000 /* SMBus Data In */ +#define E1000_MANC_SMB_DATA_OUT 0x10000000 /* SMBus Data Out */ +#define E1000_MANC_SMB_CLK_OUT 0x20000000 /* SMBus Clock Out */ + +#define E1000_MANC_SMB_DATA_OUT_SHIFT 28 /* SMBus Data Out Shift */ +#define E1000_MANC_SMB_CLK_OUT_SHIFT 29 /* SMBus Clock Out Shift */ + +/* Receive Control */ +#define E1000_RCTL_RST 0x00000001 /* Software reset */ +#define E1000_RCTL_EN 0x00000002 /* enable */ +#define E1000_RCTL_SBP 0x00000004 /* store bad packet */ +#define E1000_RCTL_UPE 0x00000008 /* unicast promiscuous enable */ +#define E1000_RCTL_MPE 0x00000010 /* multicast promiscuous enab */ +#define E1000_RCTL_LPE 0x00000020 /* long packet enable */ +#define E1000_RCTL_LBM_NO 0x00000000 /* no loopback mode */ +#define E1000_RCTL_LBM_MAC 0x00000040 /* MAC loopback mode */ +#define E1000_RCTL_LBM_SLP 0x00000080 /* serial link loopback mode */ +#define E1000_RCTL_LBM_TCVR 0x000000C0 /* tcvr loopback mode */ +#define E1000_RCTL_DTYP_MASK 0x00000C00 /* Descriptor type mask */ +#define E1000_RCTL_DTYP_PS 0x00000400 /* Packet Split descriptor */ +#define E1000_RCTL_RDMTS_HALF 0x00000000 /* rx desc min threshold size */ +#define E1000_RCTL_RDMTS_QUAT 0x00000100 /* rx desc min threshold size */ +#define E1000_RCTL_RDMTS_EIGTH 0x00000200 /* rx desc min threshold size */ +#define E1000_RCTL_MO_SHIFT 12 /* multicast offset shift */ +#define E1000_RCTL_MO_0 0x00000000 /* multicast offset 11:0 */ +#define E1000_RCTL_MO_1 0x00001000 /* multicast offset 12:1 */ +#define E1000_RCTL_MO_2 0x00002000 /* multicast offset 13:2 */ +#define E1000_RCTL_MO_3 0x00003000 /* multicast offset 15:4 */ +#define E1000_RCTL_MDR 0x00004000 /* multicast desc ring 0 */ +#define E1000_RCTL_BAM 0x00008000 /* broadcast enable */ +/* these buffer sizes are valid if E1000_RCTL_BSEX is 0 */ +#define E1000_RCTL_SZ_2048 0x00000000 /* rx buffer size 2048 */ +#define E1000_RCTL_SZ_1024 0x00010000 /* rx buffer size 1024 */ +#define E1000_RCTL_SZ_512 0x00020000 /* rx buffer size 512 */ +#define E1000_RCTL_SZ_256 0x00030000 /* rx buffer size 256 */ +/* these buffer sizes are valid if E1000_RCTL_BSEX is 1 */ +#define E1000_RCTL_SZ_16384 0x00010000 /* rx buffer size 16384 */ +#define E1000_RCTL_SZ_8192 0x00020000 /* rx buffer size 8192 */ +#define E1000_RCTL_SZ_4096 0x00030000 /* rx buffer size 4096 */ +#define E1000_RCTL_VFE 0x00040000 /* vlan filter enable */ +#define E1000_RCTL_CFIEN 0x00080000 /* canonical form enable */ +#define E1000_RCTL_CFI 0x00100000 /* canonical form indicator */ +#define E1000_RCTL_DPF 0x00400000 /* discard pause frames */ +#define E1000_RCTL_PMCF 0x00800000 /* pass MAC control frames */ +#define E1000_RCTL_BSEX 0x02000000 /* Buffer size extension */ +#define E1000_RCTL_SECRC 0x04000000 /* Strip Ethernet CRC */ +#define E1000_RCTL_FLXBUF_MASK 0x78000000 /* Flexible buffer size */ +#define E1000_RCTL_FLXBUF_SHIFT 27 /* Flexible buffer shift */ + +/* + * Use byte values for the following shift parameters + * Usage: + * psrctl |= (((ROUNDUP(value0, 128) >> E1000_PSRCTL_BSIZE0_SHIFT) & + * E1000_PSRCTL_BSIZE0_MASK) | + * ((ROUNDUP(value1, 1024) >> E1000_PSRCTL_BSIZE1_SHIFT) & + * E1000_PSRCTL_BSIZE1_MASK) | + * ((ROUNDUP(value2, 1024) << E1000_PSRCTL_BSIZE2_SHIFT) & + * E1000_PSRCTL_BSIZE2_MASK) | + * ((ROUNDUP(value3, 1024) << E1000_PSRCTL_BSIZE3_SHIFT) |; + * E1000_PSRCTL_BSIZE3_MASK)) + * where value0 = [128..16256], default=256 + * value1 = [1024..64512], default=4096 + * value2 = [0..64512], default=4096 + * value3 = [0..64512], default=0 + */ + +#define E1000_PSRCTL_BSIZE0_MASK 0x0000007F +#define E1000_PSRCTL_BSIZE1_MASK 0x00003F00 +#define E1000_PSRCTL_BSIZE2_MASK 0x003F0000 +#define E1000_PSRCTL_BSIZE3_MASK 0x3F000000 + +#define E1000_PSRCTL_BSIZE0_SHIFT 7 /* Shift _right_ 7 */ +#define E1000_PSRCTL_BSIZE1_SHIFT 2 /* Shift _right_ 2 */ +#define E1000_PSRCTL_BSIZE2_SHIFT 6 /* Shift _left_ 6 */ +#define E1000_PSRCTL_BSIZE3_SHIFT 14 /* Shift _left_ 14 */ + +/* SWFW_SYNC Definitions */ +#define E1000_SWFW_EEP_SM 0x1 +#define E1000_SWFW_PHY0_SM 0x2 +#define E1000_SWFW_PHY1_SM 0x4 +#define E1000_SWFW_CSR_SM 0x8 + +/* FACTPS Definitions */ +#define E1000_FACTPS_LFS 0x40000000 /* LAN Function Select */ +/* Device Control */ +#define E1000_CTRL_FD 0x00000001 /* Full duplex.0=half; 1=full */ +#define E1000_CTRL_BEM 0x00000002 /* Endian Mode.0=little,1=big */ +#define E1000_CTRL_PRIOR 0x00000004 /* Priority on PCI. 0=rx,1=fair */ +#define E1000_CTRL_GIO_MASTER_DISABLE 0x00000004 /*Blocks new Master requests */ +#define E1000_CTRL_LRST 0x00000008 /* Link reset. 0=normal,1=reset */ +#define E1000_CTRL_TME 0x00000010 /* Test mode. 0=normal,1=test */ +#define E1000_CTRL_SLE 0x00000020 /* Serial Link on 0=dis,1=en */ +#define E1000_CTRL_ASDE 0x00000020 /* Auto-speed detect enable */ +#define E1000_CTRL_SLU 0x00000040 /* Set link up (Force Link) */ +#define E1000_CTRL_ILOS 0x00000080 /* Invert Loss-Of Signal */ +#define E1000_CTRL_SPD_SEL 0x00000300 /* Speed Select Mask */ +#define E1000_CTRL_SPD_10 0x00000000 /* Force 10Mb */ +#define E1000_CTRL_SPD_100 0x00000100 /* Force 100Mb */ +#define E1000_CTRL_SPD_1000 0x00000200 /* Force 1Gb */ +#define E1000_CTRL_BEM32 0x00000400 /* Big Endian 32 mode */ +#define E1000_CTRL_FRCSPD 0x00000800 /* Force Speed */ +#define E1000_CTRL_FRCDPX 0x00001000 /* Force Duplex */ +#define E1000_CTRL_D_UD_EN 0x00002000 /* Dock/Undock enable */ +#define E1000_CTRL_D_UD_POLARITY 0x00004000 /* Defined polarity of Dock/Undock + * indication in SDP[0] */ +#define E1000_CTRL_FORCE_PHY_RESET 0x00008000 /* Reset both PHY ports, through + * PHYRST_N pin */ +#define E1000_CTRL_EXT_LINK_EN 0x00010000 /* enable link status from external + * LINK_0 and LINK_1 pins */ +#define E1000_CTRL_SWDPIN0 0x00040000 /* SWDPIN 0 value */ +#define E1000_CTRL_SWDPIN1 0x00080000 /* SWDPIN 1 value */ +#define E1000_CTRL_SWDPIN2 0x00100000 /* SWDPIN 2 value */ +#define E1000_CTRL_SWDPIN3 0x00200000 /* SWDPIN 3 value */ +#define E1000_CTRL_SWDPIO0 0x00400000 /* SWDPIN 0 Input or output */ +#define E1000_CTRL_SWDPIO1 0x00800000 /* SWDPIN 1 input or output */ +#define E1000_CTRL_SWDPIO2 0x01000000 /* SWDPIN 2 input or output */ +#define E1000_CTRL_SWDPIO3 0x02000000 /* SWDPIN 3 input or output */ +#define E1000_CTRL_RST 0x04000000 /* Global reset */ +#define E1000_CTRL_RFCE 0x08000000 /* Receive Flow Control enable */ +#define E1000_CTRL_TFCE 0x10000000 /* Transmit flow control enable */ +#define E1000_CTRL_RTE 0x20000000 /* Routing tag enable */ +#define E1000_CTRL_VME 0x40000000 /* IEEE VLAN mode enable */ +#define E1000_CTRL_PHY_RST 0x80000000 /* PHY Reset */ +#define E1000_CTRL_SW2FW_INT 0x02000000 /* Initiate an interrupt to ME */ +#define E1000_CTRL_I2C_ENA 0x02000000 /* I2C enable */ + +/* + * Bit definitions for the Management Data IO (MDIO) and Management Data + * Clock (MDC) pins in the Device Control Register. + */ +#define E1000_CTRL_PHY_RESET_DIR E1000_CTRL_SWDPIO0 +#define E1000_CTRL_PHY_RESET E1000_CTRL_SWDPIN0 +#define E1000_CTRL_MDIO_DIR E1000_CTRL_SWDPIO2 +#define E1000_CTRL_MDIO E1000_CTRL_SWDPIN2 +#define E1000_CTRL_MDC_DIR E1000_CTRL_SWDPIO3 +#define E1000_CTRL_MDC E1000_CTRL_SWDPIN3 +#define E1000_CTRL_PHY_RESET_DIR4 E1000_CTRL_EXT_SDP4_DIR +#define E1000_CTRL_PHY_RESET4 E1000_CTRL_EXT_SDP4_DATA + +#define E1000_CONNSW_ENRGSRC 0x4 +#define E1000_PCS_CFG_PCS_EN 8 +#define E1000_PCS_LCTL_FLV_LINK_UP 1 +#define E1000_PCS_LCTL_FSV_10 0 +#define E1000_PCS_LCTL_FSV_100 2 +#define E1000_PCS_LCTL_FSV_1000 4 +#define E1000_PCS_LCTL_FDV_FULL 8 +#define E1000_PCS_LCTL_FSD 0x10 +#define E1000_PCS_LCTL_FORCE_LINK 0x20 +#define E1000_PCS_LCTL_LOW_LINK_LATCH 0x40 +#define E1000_PCS_LCTL_FORCE_FCTRL 0x80 +#define E1000_PCS_LCTL_AN_ENABLE 0x10000 +#define E1000_PCS_LCTL_AN_RESTART 0x20000 +#define E1000_PCS_LCTL_AN_TIMEOUT 0x40000 +#define E1000_PCS_LCTL_AN_SGMII_BYPASS 0x80000 +#define E1000_PCS_LCTL_AN_SGMII_TRIGGER 0x100000 +#define E1000_PCS_LCTL_FAST_LINK_TIMER 0x1000000 +#define E1000_PCS_LCTL_LINK_OK_FIX 0x2000000 +#define E1000_PCS_LCTL_CRS_ON_NI 0x4000000 +#define E1000_ENABLE_SERDES_LOOPBACK 0x0410 + +#define E1000_PCS_LSTS_LINK_OK 1 +#define E1000_PCS_LSTS_SPEED_10 0 +#define E1000_PCS_LSTS_SPEED_100 2 +#define E1000_PCS_LSTS_SPEED_1000 4 +#define E1000_PCS_LSTS_DUPLEX_FULL 8 +#define E1000_PCS_LSTS_SYNK_OK 0x10 +#define E1000_PCS_LSTS_AN_COMPLETE 0x10000 +#define E1000_PCS_LSTS_AN_PAGE_RX 0x20000 +#define E1000_PCS_LSTS_AN_TIMED_OUT 0x40000 +#define E1000_PCS_LSTS_AN_REMOTE_FAULT 0x80000 +#define E1000_PCS_LSTS_AN_ERROR_RWS 0x100000 + +/* Device Status */ +#define E1000_STATUS_FD 0x00000001 /* Full duplex.0=half,1=full */ +#define E1000_STATUS_LU 0x00000002 /* Link up.0=no,1=link */ +#define E1000_STATUS_FUNC_MASK 0x0000000C /* PCI Function Mask */ +#define E1000_STATUS_FUNC_SHIFT 2 +#define E1000_STATUS_FUNC_0 0x00000000 /* Function 0 */ +#define E1000_STATUS_FUNC_1 0x00000004 /* Function 1 */ +#define E1000_STATUS_TXOFF 0x00000010 /* transmission paused */ +#define E1000_STATUS_TBIMODE 0x00000020 /* TBI mode */ +#define E1000_STATUS_SPEED_MASK 0x000000C0 +#define E1000_STATUS_SPEED_10 0x00000000 /* Speed 10Mb/s */ +#define E1000_STATUS_SPEED_100 0x00000040 /* Speed 100Mb/s */ +#define E1000_STATUS_SPEED_1000 0x00000080 /* Speed 1000Mb/s */ +#define E1000_STATUS_LAN_INIT_DONE 0x00000200 /* Lan Init Completion by NVM */ +#define E1000_STATUS_ASDV 0x00000300 /* Auto speed detect value */ +#define E1000_STATUS_DOCK_CI 0x00000800 /* Change in Dock/Undock state. + * Clear on write '0'. */ +#define E1000_STATUS_GIO_MASTER_ENABLE 0x00080000 /* Master request status */ +#define E1000_STATUS_MTXCKOK 0x00000400 /* MTX clock running OK */ +#define E1000_STATUS_PCI66 0x00000800 /* In 66Mhz slot */ +#define E1000_STATUS_BUS64 0x00001000 /* In 64 bit slot */ +#define E1000_STATUS_PCIX_MODE 0x00002000 /* PCI-X mode */ +#define E1000_STATUS_PCIX_SPEED 0x0000C000 /* PCI-X bus speed */ +#define E1000_STATUS_BMC_SKU_0 0x00100000 /* BMC USB redirect disabled */ +#define E1000_STATUS_BMC_SKU_1 0x00200000 /* BMC SRAM disabled */ +#define E1000_STATUS_BMC_SKU_2 0x00400000 /* BMC SDRAM disabled */ +#define E1000_STATUS_BMC_CRYPTO 0x00800000 /* BMC crypto disabled */ +#define E1000_STATUS_BMC_LITE 0x01000000 /* BMC external code execution + * disabled */ +#define E1000_STATUS_RGMII_ENABLE 0x02000000 /* RGMII disabled */ +#define E1000_STATUS_FUSE_8 0x04000000 +#define E1000_STATUS_FUSE_9 0x08000000 +#define E1000_STATUS_SERDES0_DIS 0x10000000 /* SERDES disabled on port 0 */ +#define E1000_STATUS_SERDES1_DIS 0x20000000 /* SERDES disabled on port 1 */ + +/* Constants used to interpret the masked PCI-X bus speed. */ +#define E1000_STATUS_PCIX_SPEED_66 0x00000000 /* PCI-X bus speed 50-66 MHz */ +#define E1000_STATUS_PCIX_SPEED_100 0x00004000 /* PCI-X bus speed 66-100 MHz */ +#define E1000_STATUS_PCIX_SPEED_133 0x00008000 /* PCI-X bus speed 100-133 MHz */ + +#define SPEED_10 10 +#define SPEED_100 100 +#define SPEED_1000 1000 +#define HALF_DUPLEX 1 +#define FULL_DUPLEX 2 + +#define PHY_FORCE_TIME 20 + +#define ADVERTISE_10_HALF 0x0001 +#define ADVERTISE_10_FULL 0x0002 +#define ADVERTISE_100_HALF 0x0004 +#define ADVERTISE_100_FULL 0x0008 +#define ADVERTISE_1000_HALF 0x0010 /* Not used, just FYI */ +#define ADVERTISE_1000_FULL 0x0020 + +/* 1000/H is not supported, nor spec-compliant. */ +#define E1000_ALL_SPEED_DUPLEX (ADVERTISE_10_HALF | ADVERTISE_10_FULL | \ + ADVERTISE_100_HALF | ADVERTISE_100_FULL | \ + ADVERTISE_1000_FULL) +#define E1000_ALL_NOT_GIG (ADVERTISE_10_HALF | ADVERTISE_10_FULL | \ + ADVERTISE_100_HALF | ADVERTISE_100_FULL) +#define E1000_ALL_100_SPEED (ADVERTISE_100_HALF | ADVERTISE_100_FULL) +#define E1000_ALL_10_SPEED (ADVERTISE_10_HALF | ADVERTISE_10_FULL) +#define E1000_ALL_FULL_DUPLEX (ADVERTISE_10_FULL | ADVERTISE_100_FULL | \ + ADVERTISE_1000_FULL) +#define E1000_ALL_HALF_DUPLEX (ADVERTISE_10_HALF | ADVERTISE_100_HALF) + +#define AUTONEG_ADVERTISE_SPEED_DEFAULT E1000_ALL_SPEED_DUPLEX + +/* LED Control */ +#define E1000_LEDCTL_LED0_MODE_MASK 0x0000000F +#define E1000_LEDCTL_LED0_MODE_SHIFT 0 +#define E1000_LEDCTL_LED0_BLINK_RATE 0x00000020 +#define E1000_LEDCTL_LED0_IVRT 0x00000040 +#define E1000_LEDCTL_LED0_BLINK 0x00000080 +#define E1000_LEDCTL_LED1_MODE_MASK 0x00000F00 +#define E1000_LEDCTL_LED1_MODE_SHIFT 8 +#define E1000_LEDCTL_LED1_BLINK_RATE 0x00002000 +#define E1000_LEDCTL_LED1_IVRT 0x00004000 +#define E1000_LEDCTL_LED1_BLINK 0x00008000 +#define E1000_LEDCTL_LED2_MODE_MASK 0x000F0000 +#define E1000_LEDCTL_LED2_MODE_SHIFT 16 +#define E1000_LEDCTL_LED2_BLINK_RATE 0x00200000 +#define E1000_LEDCTL_LED2_IVRT 0x00400000 +#define E1000_LEDCTL_LED2_BLINK 0x00800000 +#define E1000_LEDCTL_LED3_MODE_MASK 0x0F000000 +#define E1000_LEDCTL_LED3_MODE_SHIFT 24 +#define E1000_LEDCTL_LED3_BLINK_RATE 0x20000000 +#define E1000_LEDCTL_LED3_IVRT 0x40000000 +#define E1000_LEDCTL_LED3_BLINK 0x80000000 + +#define E1000_LEDCTL_MODE_LINK_10_1000 0x0 +#define E1000_LEDCTL_MODE_LINK_100_1000 0x1 +#define E1000_LEDCTL_MODE_LINK_UP 0x2 +#define E1000_LEDCTL_MODE_ACTIVITY 0x3 +#define E1000_LEDCTL_MODE_LINK_ACTIVITY 0x4 +#define E1000_LEDCTL_MODE_LINK_10 0x5 +#define E1000_LEDCTL_MODE_LINK_100 0x6 +#define E1000_LEDCTL_MODE_LINK_1000 0x7 +#define E1000_LEDCTL_MODE_PCIX_MODE 0x8 +#define E1000_LEDCTL_MODE_FULL_DUPLEX 0x9 +#define E1000_LEDCTL_MODE_COLLISION 0xA +#define E1000_LEDCTL_MODE_BUS_SPEED 0xB +#define E1000_LEDCTL_MODE_BUS_SIZE 0xC +#define E1000_LEDCTL_MODE_PAUSED 0xD +#define E1000_LEDCTL_MODE_LED_ON 0xE +#define E1000_LEDCTL_MODE_LED_OFF 0xF + +/* Transmit Descriptor bit definitions */ +#define E1000_TXD_DTYP_D 0x00100000 /* Data Descriptor */ +#define E1000_TXD_DTYP_C 0x00000000 /* Context Descriptor */ +#define E1000_TXD_POPTS_SHIFT 8 /* POPTS shift */ +#define E1000_TXD_POPTS_IXSM 0x01 /* Insert IP checksum */ +#define E1000_TXD_POPTS_TXSM 0x02 /* Insert TCP/UDP checksum */ +#define E1000_TXD_CMD_EOP 0x01000000 /* End of Packet */ +#define E1000_TXD_CMD_IFCS 0x02000000 /* Insert FCS (Ethernet CRC) */ +#define E1000_TXD_CMD_IC 0x04000000 /* Insert Checksum */ +#define E1000_TXD_CMD_RS 0x08000000 /* Report Status */ +#define E1000_TXD_CMD_RPS 0x10000000 /* Report Packet Sent */ +#define E1000_TXD_CMD_DEXT 0x20000000 /* Descriptor extension (0 = legacy) */ +#define E1000_TXD_CMD_VLE 0x40000000 /* Add VLAN tag */ +#define E1000_TXD_CMD_IDE 0x80000000 /* Enable Tidv register */ +#define E1000_TXD_STAT_DD 0x00000001 /* Descriptor Done */ +#define E1000_TXD_STAT_EC 0x00000002 /* Excess Collisions */ +#define E1000_TXD_STAT_LC 0x00000004 /* Late Collisions */ +#define E1000_TXD_STAT_TU 0x00000008 /* Transmit underrun */ +#define E1000_TXD_CMD_TCP 0x01000000 /* TCP packet */ +#define E1000_TXD_CMD_IP 0x02000000 /* IP packet */ +#define E1000_TXD_CMD_TSE 0x04000000 /* TCP Seg enable */ +#define E1000_TXD_STAT_TC 0x00000004 /* Tx Underrun */ +/* Extended desc bits for Linksec and timesync */ +#define E1000_TXD_CMD_LINKSEC 0x10000000 /* Apply LinkSec on packet */ +#define E1000_TXD_EXTCMD_TSTAMP 0x00000010 /* IEEE1588 Timestamp packet */ + +/* Transmit Control */ +#define E1000_TCTL_RST 0x00000001 /* software reset */ +#define E1000_TCTL_EN 0x00000002 /* enable tx */ +#define E1000_TCTL_BCE 0x00000004 /* busy check enable */ +#define E1000_TCTL_PSP 0x00000008 /* pad short packets */ +#define E1000_TCTL_CT 0x00000ff0 /* collision threshold */ +#define E1000_TCTL_COLD 0x003ff000 /* collision distance */ +#define E1000_TCTL_SWXOFF 0x00400000 /* SW Xoff transmission */ +#define E1000_TCTL_PBE 0x00800000 /* Packet Burst Enable */ +#define E1000_TCTL_RTLC 0x01000000 /* Re-transmit on late collision */ +#define E1000_TCTL_NRTU 0x02000000 /* No Re-transmit on underrun */ +#define E1000_TCTL_MULR 0x10000000 /* Multiple request support */ + +/* Transmit Arbitration Count */ +#define E1000_TARC0_ENABLE 0x00000400 /* Enable Tx Queue 0 */ + +/* SerDes Control */ +#define E1000_SCTL_DISABLE_SERDES_LOOPBACK 0x0400 + +/* Receive Checksum Control */ +#define E1000_RXCSUM_PCSS_MASK 0x000000FF /* Packet Checksum Start */ +#define E1000_RXCSUM_IPOFL 0x00000100 /* IPv4 checksum offload */ +#define E1000_RXCSUM_TUOFL 0x00000200 /* TCP / UDP checksum offload */ +#define E1000_RXCSUM_IPV6OFL 0x00000400 /* IPv6 checksum offload */ +#define E1000_RXCSUM_CRCOFL 0x00000800 /* CRC32 offload enable */ +#define E1000_RXCSUM_IPPCSE 0x00001000 /* IP payload checksum enable */ +#define E1000_RXCSUM_PCSD 0x00002000 /* packet checksum disabled */ + +/* Header split receive */ +#define E1000_RFCTL_ISCSI_DIS 0x00000001 +#define E1000_RFCTL_ISCSI_DWC_MASK 0x0000003E +#define E1000_RFCTL_ISCSI_DWC_SHIFT 1 +#define E1000_RFCTL_NFSW_DIS 0x00000040 +#define E1000_RFCTL_NFSR_DIS 0x00000080 +#define E1000_RFCTL_NFS_VER_MASK 0x00000300 +#define E1000_RFCTL_NFS_VER_SHIFT 8 +#define E1000_RFCTL_IPV6_DIS 0x00000400 +#define E1000_RFCTL_IPV6_XSUM_DIS 0x00000800 +#define E1000_RFCTL_ACK_DIS 0x00001000 +#define E1000_RFCTL_ACKD_DIS 0x00002000 +#define E1000_RFCTL_IPFRSP_DIS 0x00004000 +#define E1000_RFCTL_EXTEN 0x00008000 +#define E1000_RFCTL_IPV6_EX_DIS 0x00010000 +#define E1000_RFCTL_NEW_IPV6_EXT_DIS 0x00020000 +#define E1000_RFCTL_LEF 0x00040000 + +/* Collision related configuration parameters */ +#define E1000_COLLISION_THRESHOLD 15 +#define E1000_CT_SHIFT 4 +#define E1000_COLLISION_DISTANCE 63 +#define E1000_COLD_SHIFT 12 + +/* Default values for the transmit IPG register */ +#define DEFAULT_82542_TIPG_IPGT 10 +#define DEFAULT_82543_TIPG_IPGT_FIBER 9 +#define DEFAULT_82543_TIPG_IPGT_COPPER 8 + +#define E1000_TIPG_IPGT_MASK 0x000003FF +#define E1000_TIPG_IPGR1_MASK 0x000FFC00 +#define E1000_TIPG_IPGR2_MASK 0x3FF00000 + +#define DEFAULT_82542_TIPG_IPGR1 2 +#define DEFAULT_82543_TIPG_IPGR1 8 +#define E1000_TIPG_IPGR1_SHIFT 10 + +#define DEFAULT_82542_TIPG_IPGR2 10 +#define DEFAULT_82543_TIPG_IPGR2 6 +#define DEFAULT_80003ES2LAN_TIPG_IPGR2 7 +#define E1000_TIPG_IPGR2_SHIFT 20 + +/* Ethertype field values */ +#define ETHERNET_IEEE_VLAN_TYPE 0x8100 /* 802.3ac packet */ + +#define ETHERNET_FCS_SIZE 4 +#define MAX_JUMBO_FRAME_SIZE 0x3F00 + +/* Extended Configuration Control and Size */ +#define E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP 0x00000020 +#define E1000_EXTCNF_CTRL_LCD_WRITE_ENABLE 0x00000001 +#define E1000_EXTCNF_CTRL_SWFLAG 0x00000020 +#define E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH_MASK 0x00FF0000 +#define E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH_SHIFT 16 +#define E1000_EXTCNF_CTRL_EXT_CNF_POINTER_MASK 0x0FFF0000 +#define E1000_EXTCNF_CTRL_EXT_CNF_POINTER_SHIFT 16 + +#define E1000_PHY_CTRL_SPD_EN 0x00000001 +#define E1000_PHY_CTRL_D0A_LPLU 0x00000002 +#define E1000_PHY_CTRL_NOND0A_LPLU 0x00000004 +#define E1000_PHY_CTRL_NOND0A_GBE_DISABLE 0x00000008 +#define E1000_PHY_CTRL_GBE_DISABLE 0x00000040 + +#define E1000_KABGTXD_BGSQLBIAS 0x00050000 + +/* PBA constants */ +#define E1000_PBA_6K 0x0006 /* 6KB */ +#define E1000_PBA_8K 0x0008 /* 8KB */ +#define E1000_PBA_12K 0x000C /* 12KB */ +#define E1000_PBA_16K 0x0010 /* 16KB */ +#define E1000_PBA_20K 0x0014 +#define E1000_PBA_22K 0x0016 +#define E1000_PBA_24K 0x0018 +#define E1000_PBA_30K 0x001E +#define E1000_PBA_32K 0x0020 +#define E1000_PBA_34K 0x0022 +#define E1000_PBA_38K 0x0026 +#define E1000_PBA_40K 0x0028 +#define E1000_PBA_48K 0x0030 /* 48KB */ +#define E1000_PBA_64K 0x0040 /* 64KB */ + +#define E1000_PBS_16K E1000_PBA_16K +#define E1000_PBS_24K E1000_PBA_24K + +#define IFS_MAX 80 +#define IFS_MIN 40 +#define IFS_RATIO 4 +#define IFS_STEP 10 +#define MIN_NUM_XMITS 1000 + +/* SW Semaphore Register */ +#define E1000_SWSM_SMBI 0x00000001 /* Driver Semaphore bit */ +#define E1000_SWSM_SWESMBI 0x00000002 /* FW Semaphore bit */ +#define E1000_SWSM_WMNG 0x00000004 /* Wake MNG Clock */ +#define E1000_SWSM_DRV_LOAD 0x00000008 /* Driver Loaded Bit */ + +/* Interrupt Cause Read */ +#define E1000_ICR_TXDW 0x00000001 /* Transmit desc written back */ +#define E1000_ICR_TXQE 0x00000002 /* Transmit Queue empty */ +#define E1000_ICR_LSC 0x00000004 /* Link Status Change */ +#define E1000_ICR_RXSEQ 0x00000008 /* rx sequence error */ +#define E1000_ICR_RXDMT0 0x00000010 /* rx desc min. threshold (0) */ +#define E1000_ICR_RXO 0x00000040 /* rx overrun */ +#define E1000_ICR_RXT0 0x00000080 /* rx timer intr (ring 0) */ +#define E1000_ICR_VMMB 0x00000100 /* VM MB event */ +#define E1000_ICR_MDAC 0x00000200 /* MDIO access complete */ +#define E1000_ICR_RXCFG 0x00000400 /* Rx /c/ ordered set */ +#define E1000_ICR_GPI_EN0 0x00000800 /* GP Int 0 */ +#define E1000_ICR_GPI_EN1 0x00001000 /* GP Int 1 */ +#define E1000_ICR_GPI_EN2 0x00002000 /* GP Int 2 */ +#define E1000_ICR_GPI_EN3 0x00004000 /* GP Int 3 */ +#define E1000_ICR_TXD_LOW 0x00008000 +#define E1000_ICR_SRPD 0x00010000 +#define E1000_ICR_ACK 0x00020000 /* Receive Ack frame */ +#define E1000_ICR_MNG 0x00040000 /* Manageability event */ +#define E1000_ICR_DOCK 0x00080000 /* Dock/Undock */ +#define E1000_ICR_INT_ASSERTED 0x80000000 /* If this bit asserted, the driver + * should claim the interrupt */ +#define E1000_ICR_RXD_FIFO_PAR0 0x00100000 /* Q0 Rx desc FIFO parity error */ +#define E1000_ICR_TXD_FIFO_PAR0 0x00200000 /* Q0 Tx desc FIFO parity error */ +#define E1000_ICR_HOST_ARB_PAR 0x00400000 /* host arb read buffer parity err */ +#define E1000_ICR_PB_PAR 0x00800000 /* packet buffer parity error */ +#define E1000_ICR_RXD_FIFO_PAR1 0x01000000 /* Q1 Rx desc FIFO parity error */ +#define E1000_ICR_TXD_FIFO_PAR1 0x02000000 /* Q1 Tx desc FIFO parity error */ +#define E1000_ICR_ALL_PARITY 0x03F00000 /* all parity error bits */ +#define E1000_ICR_DSW 0x00000020 /* FW changed the status of DISSW + * bit in the FWSM */ +#define E1000_ICR_PHYINT 0x00001000 /* LAN connected device generates + * an interrupt */ +#define E1000_ICR_DOUTSYNC 0x10000000 /* NIC DMA out of sync */ +#define E1000_ICR_EPRST 0x00100000 /* ME hardware reset occurs */ +#define E1000_ICR_RXQ0 0x00100000 /* Rx Queue 0 Interrupt */ +#define E1000_ICR_RXQ1 0x00200000 /* Rx Queue 1 Interrupt */ +#define E1000_ICR_TXQ0 0x00400000 /* Tx Queue 0 Interrupt */ +#define E1000_ICR_TXQ1 0x00800000 /* Tx Queue 1 Interrupt */ +#define E1000_ICR_OTHER 0x01000000 /* Other Interrupts */ + +/* Extended Interrupt Cause Read */ +#define E1000_EICR_RX_QUEUE0 0x00000001 /* Rx Queue 0 Interrupt */ +#define E1000_EICR_RX_QUEUE1 0x00000002 /* Rx Queue 1 Interrupt */ +#define E1000_EICR_RX_QUEUE2 0x00000004 /* Rx Queue 2 Interrupt */ +#define E1000_EICR_RX_QUEUE3 0x00000008 /* Rx Queue 3 Interrupt */ +#define E1000_EICR_TX_QUEUE0 0x00000100 /* Tx Queue 0 Interrupt */ +#define E1000_EICR_TX_QUEUE1 0x00000200 /* Tx Queue 1 Interrupt */ +#define E1000_EICR_TX_QUEUE2 0x00000400 /* Tx Queue 2 Interrupt */ +#define E1000_EICR_TX_QUEUE3 0x00000800 /* Tx Queue 3 Interrupt */ +#define E1000_EICR_TCP_TIMER 0x40000000 /* TCP Timer */ +#define E1000_EICR_OTHER 0x80000000 /* Interrupt Cause Active */ +/* TCP Timer */ +#define E1000_TCPTIMER_KS 0x00000100 /* KickStart */ +#define E1000_TCPTIMER_COUNT_ENABLE 0x00000200 /* Count Enable */ +#define E1000_TCPTIMER_COUNT_FINISH 0x00000400 /* Count finish */ +#define E1000_TCPTIMER_LOOP 0x00000800 /* Loop */ + +/* + * This defines the bits that are set in the Interrupt Mask + * Set/Read Register. Each bit is documented below: + * o RXDMT0 = Receive Descriptor Minimum Threshold hit (ring 0) + * o RXSEQ = Receive Sequence Error + */ +#define POLL_IMS_ENABLE_MASK ( \ + E1000_IMS_RXDMT0 | \ + E1000_IMS_RXSEQ) + +/* + * This defines the bits that are set in the Interrupt Mask + * Set/Read Register. Each bit is documented below: + * o RXT0 = Receiver Timer Interrupt (ring 0) + * o TXDW = Transmit Descriptor Written Back + * o RXDMT0 = Receive Descriptor Minimum Threshold hit (ring 0) + * o RXSEQ = Receive Sequence Error + * o LSC = Link Status Change + */ +#define IMS_ENABLE_MASK ( \ + E1000_IMS_RXT0 | \ + E1000_IMS_TXDW | \ + E1000_IMS_RXDMT0 | \ + E1000_IMS_RXSEQ | \ + E1000_IMS_LSC) + +/* Interrupt Mask Set */ +#define E1000_IMS_TXDW E1000_ICR_TXDW /* Transmit desc written back */ +#define E1000_IMS_TXQE E1000_ICR_TXQE /* Transmit Queue empty */ +#define E1000_IMS_LSC E1000_ICR_LSC /* Link Status Change */ +#define E1000_IMS_VMMB E1000_ICR_VMMB /* Mail box activity */ +#define E1000_IMS_RXSEQ E1000_ICR_RXSEQ /* rx sequence error */ +#define E1000_IMS_RXDMT0 E1000_ICR_RXDMT0 /* rx desc min. threshold */ +#define E1000_IMS_RXO E1000_ICR_RXO /* rx overrun */ +#define E1000_IMS_RXT0 E1000_ICR_RXT0 /* rx timer intr */ +#define E1000_IMS_MDAC E1000_ICR_MDAC /* MDIO access complete */ +#define E1000_IMS_RXCFG E1000_ICR_RXCFG /* Rx /c/ ordered set */ +#define E1000_IMS_GPI_EN0 E1000_ICR_GPI_EN0 /* GP Int 0 */ +#define E1000_IMS_GPI_EN1 E1000_ICR_GPI_EN1 /* GP Int 1 */ +#define E1000_IMS_GPI_EN2 E1000_ICR_GPI_EN2 /* GP Int 2 */ +#define E1000_IMS_GPI_EN3 E1000_ICR_GPI_EN3 /* GP Int 3 */ +#define E1000_IMS_TXD_LOW E1000_ICR_TXD_LOW +#define E1000_IMS_SRPD E1000_ICR_SRPD +#define E1000_IMS_ACK E1000_ICR_ACK /* Receive Ack frame */ +#define E1000_IMS_MNG E1000_ICR_MNG /* Manageability event */ +#define E1000_IMS_DOCK E1000_ICR_DOCK /* Dock/Undock */ +#define E1000_IMS_RXD_FIFO_PAR0 E1000_ICR_RXD_FIFO_PAR0 /* Q0 Rx desc FIFO + * parity error */ +#define E1000_IMS_TXD_FIFO_PAR0 E1000_ICR_TXD_FIFO_PAR0 /* Q0 Tx desc FIFO + * parity error */ +#define E1000_IMS_HOST_ARB_PAR E1000_ICR_HOST_ARB_PAR /* host arb read buffer + * parity error */ +#define E1000_IMS_PB_PAR E1000_ICR_PB_PAR /* packet buffer parity + * error */ +#define E1000_IMS_RXD_FIFO_PAR1 E1000_ICR_RXD_FIFO_PAR1 /* Q1 Rx desc FIFO + * parity error */ +#define E1000_IMS_TXD_FIFO_PAR1 E1000_ICR_TXD_FIFO_PAR1 /* Q1 Tx desc FIFO + * parity error */ +#define E1000_IMS_DSW E1000_ICR_DSW +#define E1000_IMS_PHYINT E1000_ICR_PHYINT +#define E1000_IMS_DOUTSYNC E1000_ICR_DOUTSYNC /* NIC DMA out of sync */ +#define E1000_IMS_EPRST E1000_ICR_EPRST +#define E1000_IMS_RXQ0 E1000_ICR_RXQ0 /* Rx Queue 0 Interrupt */ +#define E1000_IMS_RXQ1 E1000_ICR_RXQ1 /* Rx Queue 1 Interrupt */ +#define E1000_IMS_TXQ0 E1000_ICR_TXQ0 /* Tx Queue 0 Interrupt */ +#define E1000_IMS_TXQ1 E1000_ICR_TXQ1 /* Tx Queue 1 Interrupt */ +#define E1000_IMS_OTHER E1000_ICR_OTHER /* Other Interrupts */ + +/* Extended Interrupt Mask Set */ +#define E1000_EIMS_RX_QUEUE0 E1000_EICR_RX_QUEUE0 /* Rx Queue 0 Interrupt */ +#define E1000_EIMS_RX_QUEUE1 E1000_EICR_RX_QUEUE1 /* Rx Queue 1 Interrupt */ +#define E1000_EIMS_RX_QUEUE2 E1000_EICR_RX_QUEUE2 /* Rx Queue 2 Interrupt */ +#define E1000_EIMS_RX_QUEUE3 E1000_EICR_RX_QUEUE3 /* Rx Queue 3 Interrupt */ +#define E1000_EIMS_TX_QUEUE0 E1000_EICR_TX_QUEUE0 /* Tx Queue 0 Interrupt */ +#define E1000_EIMS_TX_QUEUE1 E1000_EICR_TX_QUEUE1 /* Tx Queue 1 Interrupt */ +#define E1000_EIMS_TX_QUEUE2 E1000_EICR_TX_QUEUE2 /* Tx Queue 2 Interrupt */ +#define E1000_EIMS_TX_QUEUE3 E1000_EICR_TX_QUEUE3 /* Tx Queue 3 Interrupt */ +#define E1000_EIMS_TCP_TIMER E1000_EICR_TCP_TIMER /* TCP Timer */ +#define E1000_EIMS_OTHER E1000_EICR_OTHER /* Interrupt Cause Active */ + +/* Interrupt Cause Set */ +#define E1000_ICS_TXDW E1000_ICR_TXDW /* Transmit desc written back */ +#define E1000_ICS_TXQE E1000_ICR_TXQE /* Transmit Queue empty */ +#define E1000_ICS_LSC E1000_ICR_LSC /* Link Status Change */ +#define E1000_ICS_RXSEQ E1000_ICR_RXSEQ /* rx sequence error */ +#define E1000_ICS_RXDMT0 E1000_ICR_RXDMT0 /* rx desc min. threshold */ +#define E1000_ICS_RXO E1000_ICR_RXO /* rx overrun */ +#define E1000_ICS_RXT0 E1000_ICR_RXT0 /* rx timer intr */ +#define E1000_ICS_MDAC E1000_ICR_MDAC /* MDIO access complete */ +#define E1000_ICS_RXCFG E1000_ICR_RXCFG /* Rx /c/ ordered set */ +#define E1000_ICS_GPI_EN0 E1000_ICR_GPI_EN0 /* GP Int 0 */ +#define E1000_ICS_GPI_EN1 E1000_ICR_GPI_EN1 /* GP Int 1 */ +#define E1000_ICS_GPI_EN2 E1000_ICR_GPI_EN2 /* GP Int 2 */ +#define E1000_ICS_GPI_EN3 E1000_ICR_GPI_EN3 /* GP Int 3 */ +#define E1000_ICS_TXD_LOW E1000_ICR_TXD_LOW +#define E1000_ICS_SRPD E1000_ICR_SRPD +#define E1000_ICS_ACK E1000_ICR_ACK /* Receive Ack frame */ +#define E1000_ICS_MNG E1000_ICR_MNG /* Manageability event */ +#define E1000_ICS_DOCK E1000_ICR_DOCK /* Dock/Undock */ +#define E1000_ICS_RXD_FIFO_PAR0 E1000_ICR_RXD_FIFO_PAR0 /* Q0 Rx desc FIFO + * parity error */ +#define E1000_ICS_TXD_FIFO_PAR0 E1000_ICR_TXD_FIFO_PAR0 /* Q0 Tx desc FIFO + * parity error */ +#define E1000_ICS_HOST_ARB_PAR E1000_ICR_HOST_ARB_PAR /* host arb read buffer + * parity error */ +#define E1000_ICS_PB_PAR E1000_ICR_PB_PAR /* packet buffer parity + * error */ +#define E1000_ICS_RXD_FIFO_PAR1 E1000_ICR_RXD_FIFO_PAR1 /* Q1 Rx desc FIFO + * parity error */ +#define E1000_ICS_TXD_FIFO_PAR1 E1000_ICR_TXD_FIFO_PAR1 /* Q1 Tx desc FIFO + * parity error */ +#define E1000_ICS_DSW E1000_ICR_DSW +#define E1000_ICS_DOUTSYNC E1000_ICR_DOUTSYNC /* NIC DMA out of sync */ +#define E1000_ICS_PHYINT E1000_ICR_PHYINT +#define E1000_ICS_EPRST E1000_ICR_EPRST + +/* Extended Interrupt Cause Set */ +#define E1000_EICS_RX_QUEUE0 E1000_EICR_RX_QUEUE0 /* Rx Queue 0 Interrupt */ +#define E1000_EICS_RX_QUEUE1 E1000_EICR_RX_QUEUE1 /* Rx Queue 1 Interrupt */ +#define E1000_EICS_RX_QUEUE2 E1000_EICR_RX_QUEUE2 /* Rx Queue 2 Interrupt */ +#define E1000_EICS_RX_QUEUE3 E1000_EICR_RX_QUEUE3 /* Rx Queue 3 Interrupt */ +#define E1000_EICS_TX_QUEUE0 E1000_EICR_TX_QUEUE0 /* Tx Queue 0 Interrupt */ +#define E1000_EICS_TX_QUEUE1 E1000_EICR_TX_QUEUE1 /* Tx Queue 1 Interrupt */ +#define E1000_EICS_TX_QUEUE2 E1000_EICR_TX_QUEUE2 /* Tx Queue 2 Interrupt */ +#define E1000_EICS_TX_QUEUE3 E1000_EICR_TX_QUEUE3 /* Tx Queue 3 Interrupt */ +#define E1000_EICS_TCP_TIMER E1000_EICR_TCP_TIMER /* TCP Timer */ +#define E1000_EICS_OTHER E1000_EICR_OTHER /* Interrupt Cause Active */ + +/* Transmit Descriptor Control */ +#define E1000_TXDCTL_PTHRESH 0x0000003F /* TXDCTL Prefetch Threshold */ +#define E1000_TXDCTL_HTHRESH 0x00003F00 /* TXDCTL Host Threshold */ +#define E1000_TXDCTL_WTHRESH 0x003F0000 /* TXDCTL Writeback Threshold */ +#define E1000_TXDCTL_GRAN 0x01000000 /* TXDCTL Granularity */ +#define E1000_TXDCTL_LWTHRESH 0xFE000000 /* TXDCTL Low Threshold */ +#define E1000_TXDCTL_FULL_TX_DESC_WB 0x01010000 /* GRAN=1, WTHRESH=1 */ +#define E1000_TXDCTL_MAX_TX_DESC_PREFETCH 0x0100001F /* GRAN=1, PTHRESH=31 */ +/* Enable the counting of descriptors still to be processed. */ +#define E1000_TXDCTL_COUNT_DESC 0x00400000 + +/* Flow Control Constants */ +#define FLOW_CONTROL_ADDRESS_LOW 0x00C28001 +#define FLOW_CONTROL_ADDRESS_HIGH 0x00000100 +#define FLOW_CONTROL_TYPE 0x8808 + +/* 802.1q VLAN Packet Size */ +#define VLAN_TAG_SIZE 4 /* 802.3ac tag (not DMA'd) */ +#define E1000_VLAN_FILTER_TBL_SIZE 128 /* VLAN Filter Table (4096 bits) */ + +/* Receive Address */ +/* + * Number of high/low register pairs in the RAR. The RAR (Receive Address + * Registers) holds the directed and multicast addresses that we monitor. + * Technically, we have 16 spots. However, we reserve one of these spots + * (RAR[15]) for our directed address used by controllers with + * manageability enabled, allowing us room for 15 multicast addresses. + */ +#define E1000_RAR_ENTRIES 15 +#define E1000_RAH_AV 0x80000000 /* Receive descriptor valid */ + +/* Error Codes */ +#define E1000_SUCCESS 0 +#define E1000_ERR_NVM 1 +#define E1000_ERR_PHY 2 +#define E1000_ERR_CONFIG 3 +#define E1000_ERR_PARAM 4 +#define E1000_ERR_MAC_INIT 5 +#define E1000_ERR_PHY_TYPE 6 +#define E1000_ERR_RESET 9 +#define E1000_ERR_MASTER_REQUESTS_PENDING 10 +#define E1000_ERR_HOST_INTERFACE_COMMAND 11 +#define E1000_BLK_PHY_RESET 12 +#define E1000_ERR_SWFW_SYNC 13 +#define E1000_NOT_IMPLEMENTED 14 + +/* Loop limit on how long we wait for auto-negotiation to complete */ +#define FIBER_LINK_UP_LIMIT 50 +#define COPPER_LINK_UP_LIMIT 10 +#define PHY_AUTO_NEG_LIMIT 45 +#define PHY_FORCE_LIMIT 20 +/* Number of 100 microseconds we wait for PCI Express master disable */ +#define MASTER_DISABLE_TIMEOUT 800 +/* Number of milliseconds we wait for PHY configuration done after MAC reset */ +#define PHY_CFG_TIMEOUT 100 +/* Number of 2 milliseconds we wait for acquiring MDIO ownership. */ +#define MDIO_OWNERSHIP_TIMEOUT 10 +/* Number of milliseconds for NVM auto read done after MAC reset. */ +#define AUTO_READ_DONE_TIMEOUT 10 + +/* Flow Control */ +#define E1000_FCRTH_RTH 0x0000FFF8 /* Mask Bits[15:3] for RTH */ +#define E1000_FCRTH_XFCE 0x80000000 /* External Flow Control Enable */ +#define E1000_FCRTL_RTL 0x0000FFF8 /* Mask Bits[15:3] for RTL */ +#define E1000_FCRTL_XONE 0x80000000 /* Enable XON frame transmission */ + +/* Transmit Configuration Word */ +#define E1000_TXCW_FD 0x00000020 /* TXCW full duplex */ +#define E1000_TXCW_HD 0x00000040 /* TXCW half duplex */ +#define E1000_TXCW_PAUSE 0x00000080 /* TXCW sym pause request */ +#define E1000_TXCW_ASM_DIR 0x00000100 /* TXCW astm pause direction */ +#define E1000_TXCW_PAUSE_MASK 0x00000180 /* TXCW pause request mask */ +#define E1000_TXCW_RF 0x00003000 /* TXCW remote fault */ +#define E1000_TXCW_NP 0x00008000 /* TXCW next page */ +#define E1000_TXCW_CW 0x0000ffff /* TxConfigWord mask */ +#define E1000_TXCW_TXC 0x40000000 /* Transmit Config control */ +#define E1000_TXCW_ANE 0x80000000 /* Auto-neg enable */ + +/* Receive Configuration Word */ +#define E1000_RXCW_CW 0x0000ffff /* RxConfigWord mask */ +#define E1000_RXCW_NC 0x04000000 /* Receive config no carrier */ +#define E1000_RXCW_IV 0x08000000 /* Receive config invalid */ +#define E1000_RXCW_CC 0x10000000 /* Receive config change */ +#define E1000_RXCW_C 0x20000000 /* Receive config */ +#define E1000_RXCW_SYNCH 0x40000000 /* Receive config synch */ +#define E1000_RXCW_ANC 0x80000000 /* Auto-neg complete */ + +/* PCI Express Control */ +#define E1000_GCR_RXD_NO_SNOOP 0x00000001 +#define E1000_GCR_RXDSCW_NO_SNOOP 0x00000002 +#define E1000_GCR_RXDSCR_NO_SNOOP 0x00000004 +#define E1000_GCR_TXD_NO_SNOOP 0x00000008 +#define E1000_GCR_TXDSCW_NO_SNOOP 0x00000010 +#define E1000_GCR_TXDSCR_NO_SNOOP 0x00000020 + +#define PCIE_NO_SNOOP_ALL (E1000_GCR_RXD_NO_SNOOP | \ + E1000_GCR_RXDSCW_NO_SNOOP | \ + E1000_GCR_RXDSCR_NO_SNOOP | \ + E1000_GCR_TXD_NO_SNOOP | \ + E1000_GCR_TXDSCW_NO_SNOOP | \ + E1000_GCR_TXDSCR_NO_SNOOP) + +/* PHY Control Register */ +#define MII_CR_SPEED_SELECT_MSB 0x0040 /* bits 6,13: 10=1000, 01=100, 00=10 */ +#define MII_CR_COLL_TEST_ENABLE 0x0080 /* Collision test enable */ +#define MII_CR_FULL_DUPLEX 0x0100 /* FDX =1, half duplex =0 */ +#define MII_CR_RESTART_AUTO_NEG 0x0200 /* Restart auto negotiation */ +#define MII_CR_ISOLATE 0x0400 /* Isolate PHY from MII */ +#define MII_CR_POWER_DOWN 0x0800 /* Power down */ +#define MII_CR_AUTO_NEG_EN 0x1000 /* Auto Neg Enable */ +#define MII_CR_SPEED_SELECT_LSB 0x2000 /* bits 6,13: 10=1000, 01=100, 00=10 */ +#define MII_CR_LOOPBACK 0x4000 /* 0 = normal, 1 = loopback */ +#define MII_CR_RESET 0x8000 /* 0 = normal, 1 = PHY reset */ +#define MII_CR_SPEED_1000 0x0040 +#define MII_CR_SPEED_100 0x2000 +#define MII_CR_SPEED_10 0x0000 + +/* PHY Status Register */ +#define MII_SR_EXTENDED_CAPS 0x0001 /* Extended register capabilities */ +#define MII_SR_JABBER_DETECT 0x0002 /* Jabber Detected */ +#define MII_SR_LINK_STATUS 0x0004 /* Link Status 1 = link */ +#define MII_SR_AUTONEG_CAPS 0x0008 /* Auto Neg Capable */ +#define MII_SR_REMOTE_FAULT 0x0010 /* Remote Fault Detect */ +#define MII_SR_AUTONEG_COMPLETE 0x0020 /* Auto Neg Complete */ +#define MII_SR_PREAMBLE_SUPPRESS 0x0040 /* Preamble may be suppressed */ +#define MII_SR_EXTENDED_STATUS 0x0100 /* Ext. status info in Reg 0x0F */ +#define MII_SR_100T2_HD_CAPS 0x0200 /* 100T2 Half Duplex Capable */ +#define MII_SR_100T2_FD_CAPS 0x0400 /* 100T2 Full Duplex Capable */ +#define MII_SR_10T_HD_CAPS 0x0800 /* 10T Half Duplex Capable */ +#define MII_SR_10T_FD_CAPS 0x1000 /* 10T Full Duplex Capable */ +#define MII_SR_100X_HD_CAPS 0x2000 /* 100X Half Duplex Capable */ +#define MII_SR_100X_FD_CAPS 0x4000 /* 100X Full Duplex Capable */ +#define MII_SR_100T4_CAPS 0x8000 /* 100T4 Capable */ + +/* Autoneg Advertisement Register */ +#define NWAY_AR_SELECTOR_FIELD 0x0001 /* indicates IEEE 802.3 CSMA/CD */ +#define NWAY_AR_10T_HD_CAPS 0x0020 /* 10T Half Duplex Capable */ +#define NWAY_AR_10T_FD_CAPS 0x0040 /* 10T Full Duplex Capable */ +#define NWAY_AR_100TX_HD_CAPS 0x0080 /* 100TX Half Duplex Capable */ +#define NWAY_AR_100TX_FD_CAPS 0x0100 /* 100TX Full Duplex Capable */ +#define NWAY_AR_100T4_CAPS 0x0200 /* 100T4 Capable */ +#define NWAY_AR_PAUSE 0x0400 /* Pause operation desired */ +#define NWAY_AR_ASM_DIR 0x0800 /* Asymmetric Pause Direction bit */ +#define NWAY_AR_REMOTE_FAULT 0x2000 /* Remote Fault detected */ +#define NWAY_AR_NEXT_PAGE 0x8000 /* Next Page ability supported */ + +/* Link Partner Ability Register (Base Page) */ +#define NWAY_LPAR_SELECTOR_FIELD 0x0000 /* LP protocol selector field */ +#define NWAY_LPAR_10T_HD_CAPS 0x0020 /* LP is 10T Half Duplex Capable */ +#define NWAY_LPAR_10T_FD_CAPS 0x0040 /* LP is 10T Full Duplex Capable */ +#define NWAY_LPAR_100TX_HD_CAPS 0x0080 /* LP is 100TX Half Duplex Capable */ +#define NWAY_LPAR_100TX_FD_CAPS 0x0100 /* LP is 100TX Full Duplex Capable */ +#define NWAY_LPAR_100T4_CAPS 0x0200 /* LP is 100T4 Capable */ +#define NWAY_LPAR_PAUSE 0x0400 /* LP Pause operation desired */ +#define NWAY_LPAR_ASM_DIR 0x0800 /* LP Asymmetric Pause Direction bit */ +#define NWAY_LPAR_REMOTE_FAULT 0x2000 /* LP has detected Remote Fault */ +#define NWAY_LPAR_ACKNOWLEDGE 0x4000 /* LP has rx'd link code word */ +#define NWAY_LPAR_NEXT_PAGE 0x8000 /* Next Page ability supported */ + +/* Autoneg Expansion Register */ +#define NWAY_ER_LP_NWAY_CAPS 0x0001 /* LP has Auto Neg Capability */ +#define NWAY_ER_PAGE_RXD 0x0002 /* LP is 10T Half Duplex Capable */ +#define NWAY_ER_NEXT_PAGE_CAPS 0x0004 /* LP is 10T Full Duplex Capable */ +#define NWAY_ER_LP_NEXT_PAGE_CAPS 0x0008 /* LP is 100TX Half Duplex Capable */ +#define NWAY_ER_PAR_DETECT_FAULT 0x0010 /* LP is 100TX Full Duplex Capable */ + +/* 1000BASE-T Control Register */ +#define CR_1000T_ASYM_PAUSE 0x0080 /* Advertise asymmetric pause bit */ +#define CR_1000T_HD_CAPS 0x0100 /* Advertise 1000T HD capability */ +#define CR_1000T_FD_CAPS 0x0200 /* Advertise 1000T FD capability */ +#define CR_1000T_REPEATER_DTE 0x0400 /* 1=Repeater/switch device port */ + /* 0=DTE device */ +#define CR_1000T_MS_VALUE 0x0800 /* 1=Configure PHY as Master */ + /* 0=Configure PHY as Slave */ +#define CR_1000T_MS_ENABLE 0x1000 /* 1=Master/Slave manual config value */ + /* 0=Automatic Master/Slave config */ +#define CR_1000T_TEST_MODE_NORMAL 0x0000 /* Normal Operation */ +#define CR_1000T_TEST_MODE_1 0x2000 /* Transmit Waveform test */ +#define CR_1000T_TEST_MODE_2 0x4000 /* Master Transmit Jitter test */ +#define CR_1000T_TEST_MODE_3 0x6000 /* Slave Transmit Jitter test */ +#define CR_1000T_TEST_MODE_4 0x8000 /* Transmitter Distortion test */ + +/* 1000BASE-T Status Register */ +#define SR_1000T_IDLE_ERROR_CNT 0x00FF /* Num idle errors since last read */ +#define SR_1000T_ASYM_PAUSE_DIR 0x0100 /* LP asymmetric pause direction bit */ +#define SR_1000T_LP_HD_CAPS 0x0400 /* LP is 1000T HD capable */ +#define SR_1000T_LP_FD_CAPS 0x0800 /* LP is 1000T FD capable */ +#define SR_1000T_REMOTE_RX_STATUS 0x1000 /* Remote receiver OK */ +#define SR_1000T_LOCAL_RX_STATUS 0x2000 /* Local receiver OK */ +#define SR_1000T_MS_CONFIG_RES 0x4000 /* 1=Local Tx is Master, 0=Slave */ +#define SR_1000T_MS_CONFIG_FAULT 0x8000 /* Master/Slave config fault */ + +#define SR_1000T_PHY_EXCESSIVE_IDLE_ERR_COUNT 5 + +/* PHY 1000 MII Register/Bit Definitions */ +/* PHY Registers defined by IEEE */ +#define PHY_CONTROL 0x00 /* Control Register */ +#define PHY_STATUS 0x01 /* Status Register */ +#define PHY_ID1 0x02 /* Phy Id Reg (word 1) */ +#define PHY_ID2 0x03 /* Phy Id Reg (word 2) */ +#define PHY_AUTONEG_ADV 0x04 /* Autoneg Advertisement */ +#define PHY_LP_ABILITY 0x05 /* Link Partner Ability (Base Page) */ +#define PHY_AUTONEG_EXP 0x06 /* Autoneg Expansion Reg */ +#define PHY_NEXT_PAGE_TX 0x07 /* Next Page Tx */ +#define PHY_LP_NEXT_PAGE 0x08 /* Link Partner Next Page */ +#define PHY_1000T_CTRL 0x09 /* 1000Base-T Control Reg */ +#define PHY_1000T_STATUS 0x0A /* 1000Base-T Status Reg */ +#define PHY_EXT_STATUS 0x0F /* Extended Status Reg */ + +/* NVM Control */ +#define E1000_EECD_SK 0x00000001 /* NVM Clock */ +#define E1000_EECD_CS 0x00000002 /* NVM Chip Select */ +#define E1000_EECD_DI 0x00000004 /* NVM Data In */ +#define E1000_EECD_DO 0x00000008 /* NVM Data Out */ +#define E1000_EECD_FWE_MASK 0x00000030 +#define E1000_EECD_FWE_DIS 0x00000010 /* Disable FLASH writes */ +#define E1000_EECD_FWE_EN 0x00000020 /* Enable FLASH writes */ +#define E1000_EECD_FWE_SHIFT 4 +#define E1000_EECD_REQ 0x00000040 /* NVM Access Request */ +#define E1000_EECD_GNT 0x00000080 /* NVM Access Grant */ +#define E1000_EECD_PRES 0x00000100 /* NVM Present */ +#define E1000_EECD_SIZE 0x00000200 /* NVM Size (0=64 word 1=256 word) */ +/* NVM Addressing bits based on type 0=small, 1=large */ +#define E1000_EECD_ADDR_BITS 0x00000400 +#define E1000_EECD_TYPE 0x00002000 /* NVM Type (1-SPI, 0-Microwire) */ +#ifndef E1000_NVM_GRANT_ATTEMPTS +#define E1000_NVM_GRANT_ATTEMPTS 1000 /* NVM # attempts to gain grant */ +#endif +#define E1000_EECD_AUTO_RD 0x00000200 /* NVM Auto Read done */ +#define E1000_EECD_SIZE_EX_MASK 0x00007800 /* NVM Size */ +#define E1000_EECD_SIZE_EX_SHIFT 11 +#define E1000_EECD_NVADDS 0x00018000 /* NVM Address Size */ +#define E1000_EECD_SELSHAD 0x00020000 /* Select Shadow RAM */ +#define E1000_EECD_INITSRAM 0x00040000 /* Initialize Shadow RAM */ +#define E1000_EECD_FLUPD 0x00080000 /* Update FLASH */ +#define E1000_EECD_AUPDEN 0x00100000 /* Enable Autonomous FLASH update */ +#define E1000_EECD_SHADV 0x00200000 /* Shadow RAM Data Valid */ +#define E1000_EECD_SEC1VAL 0x00400000 /* Sector One Valid */ +#define E1000_EECD_SECVAL_SHIFT 22 + +#define E1000_NVM_SWDPIN0 0x0001 /* SWDPIN 0 NVM Value */ +#define E1000_NVM_LED_LOGIC 0x0020 /* Led Logic Word */ +#define E1000_NVM_RW_REG_DATA 16 /* Offset to data in NVM read/write regs */ +#define E1000_NVM_RW_REG_DONE 2 /* Offset to READ/WRITE done bit */ +#define E1000_NVM_RW_REG_START 1 /* Start operation */ +#define E1000_NVM_RW_ADDR_SHIFT 2 /* Shift to the address bits */ +#define E1000_NVM_POLL_WRITE 1 /* Flag for polling for write complete */ +#define E1000_NVM_POLL_READ 0 /* Flag for polling for read complete */ +#define E1000_FLASH_UPDATES 2000 + +/* NVM Word Offsets */ +#define NVM_COMPAT 0x0003 +#define NVM_ID_LED_SETTINGS 0x0004 +#define NVM_VERSION 0x0005 +#define NVM_SERDES_AMPLITUDE 0x0006 /* SERDES output amplitude */ +#define NVM_PHY_CLASS_WORD 0x0007 +#define NVM_INIT_CONTROL1_REG 0x000A +#define NVM_INIT_CONTROL2_REG 0x000F +#define NVM_SWDEF_PINS_CTRL_PORT_1 0x0010 +#define NVM_INIT_CONTROL3_PORT_B 0x0014 +#define NVM_INIT_3GIO_3 0x001A +#define NVM_SWDEF_PINS_CTRL_PORT_0 0x0020 +#define NVM_INIT_CONTROL3_PORT_A 0x0024 +#define NVM_CFG 0x0012 +#define NVM_FLASH_VERSION 0x0032 +#define NVM_ALT_MAC_ADDR_PTR 0x0037 +#define NVM_CHECKSUM_REG 0x003F + +#define E1000_NVM_CFG_DONE_PORT_0 0x40000 /* MNG config cycle done */ +#define E1000_NVM_CFG_DONE_PORT_1 0x80000 /* ...for second port */ + +/* Mask bits for fields in Word 0x0f of the NVM */ +#define NVM_WORD0F_PAUSE_MASK 0x3000 +#define NVM_WORD0F_PAUSE 0x1000 +#define NVM_WORD0F_ASM_DIR 0x2000 +#define NVM_WORD0F_ANE 0x0800 +#define NVM_WORD0F_SWPDIO_EXT_MASK 0x00F0 +#define NVM_WORD0F_LPLU 0x0001 + +/* Mask bits for fields in Word 0x1a of the NVM */ +#define NVM_WORD1A_ASPM_MASK 0x000C + +/* For checksumming, the sum of all words in the NVM should equal 0xBABA. */ +#define NVM_SUM 0xBABA + +#define NVM_MAC_ADDR_OFFSET 0 +#define NVM_PBA_OFFSET_0 8 +#define NVM_PBA_OFFSET_1 9 +#define NVM_RESERVED_WORD 0xFFFF +#define NVM_PHY_CLASS_A 0x8000 +#define NVM_SERDES_AMPLITUDE_MASK 0x000F +#define NVM_SIZE_MASK 0x1C00 +#define NVM_SIZE_SHIFT 10 +#define NVM_WORD_SIZE_BASE_SHIFT 6 +#define NVM_SWDPIO_EXT_SHIFT 4 + +/* NVM Commands - Microwire */ +#define NVM_READ_OPCODE_MICROWIRE 0x6 /* NVM read opcode */ +#define NVM_WRITE_OPCODE_MICROWIRE 0x5 /* NVM write opcode */ +#define NVM_ERASE_OPCODE_MICROWIRE 0x7 /* NVM erase opcode */ +#define NVM_EWEN_OPCODE_MICROWIRE 0x13 /* NVM erase/write enable */ +#define NVM_EWDS_OPCODE_MICROWIRE 0x10 /* NVM erase/write disable */ + +/* NVM Commands - SPI */ +#define NVM_MAX_RETRY_SPI 5000 /* Max wait of 5ms, for RDY signal */ +#define NVM_READ_OPCODE_SPI 0x03 /* NVM read opcode */ +#define NVM_WRITE_OPCODE_SPI 0x02 /* NVM write opcode */ +#define NVM_A8_OPCODE_SPI 0x08 /* opcode bit-3 = address bit-8 */ +#define NVM_WREN_OPCODE_SPI 0x06 /* NVM set Write Enable latch */ +#define NVM_WRDI_OPCODE_SPI 0x04 /* NVM reset Write Enable latch */ +#define NVM_RDSR_OPCODE_SPI 0x05 /* NVM read Status register */ +#define NVM_WRSR_OPCODE_SPI 0x01 /* NVM write Status register */ + +/* SPI NVM Status Register */ +#define NVM_STATUS_RDY_SPI 0x01 +#define NVM_STATUS_WEN_SPI 0x02 +#define NVM_STATUS_BP0_SPI 0x04 +#define NVM_STATUS_BP1_SPI 0x08 +#define NVM_STATUS_WPEN_SPI 0x80 + +/* Word definitions for ID LED Settings */ +#define ID_LED_RESERVED_0000 0x0000 +#define ID_LED_RESERVED_FFFF 0xFFFF +#define ID_LED_DEFAULT ((ID_LED_OFF1_ON2 << 12) | \ + (ID_LED_OFF1_OFF2 << 8) | \ + (ID_LED_DEF1_DEF2 << 4) | \ + (ID_LED_DEF1_DEF2)) +#define ID_LED_DEF1_DEF2 0x1 +#define ID_LED_DEF1_ON2 0x2 +#define ID_LED_DEF1_OFF2 0x3 +#define ID_LED_ON1_DEF2 0x4 +#define ID_LED_ON1_ON2 0x5 +#define ID_LED_ON1_OFF2 0x6 +#define ID_LED_OFF1_DEF2 0x7 +#define ID_LED_OFF1_ON2 0x8 +#define ID_LED_OFF1_OFF2 0x9 + +#define IGP_ACTIVITY_LED_MASK 0xFFFFF0FF +#define IGP_ACTIVITY_LED_ENABLE 0x0300 +#define IGP_LED3_MODE 0x07000000 + +/* PCI/PCI-X/PCI-EX Config space */ +#define PCIX_COMMAND_REGISTER 0xE6 +#define PCIX_STATUS_REGISTER_LO 0xE8 +#define PCIX_STATUS_REGISTER_HI 0xEA +#define PCI_HEADER_TYPE_REGISTER 0x0E +#define PCIE_LINK_STATUS 0x12 + +#define PCIX_COMMAND_MMRBC_MASK 0x000C +#define PCIX_COMMAND_MMRBC_SHIFT 0x2 +#define PCIX_STATUS_HI_MMRBC_MASK 0x0060 +#define PCIX_STATUS_HI_MMRBC_SHIFT 0x5 +#define PCIX_STATUS_HI_MMRBC_4K 0x3 +#define PCIX_STATUS_HI_MMRBC_2K 0x2 +#define PCIX_STATUS_LO_FUNC_MASK 0x7 +#define PCI_HEADER_TYPE_MULTIFUNC 0x80 +#define PCIE_LINK_WIDTH_MASK 0x3F0 +#define PCIE_LINK_WIDTH_SHIFT 4 + +#ifndef ETH_ADDR_LEN +#define ETH_ADDR_LEN 6 +#endif + +#define PHY_REVISION_MASK 0xFFFFFFF0 +#define MAX_PHY_REG_ADDRESS 0x1F /* 5 bit address bus (0-0x1F) */ +#define MAX_PHY_MULTI_PAGE_REG 0xF + +/* Bit definitions for valid PHY IDs. */ +/* + * I = Integrated + * E = External + */ +#define M88E1000_E_PHY_ID 0x01410C50 +#define M88E1000_I_PHY_ID 0x01410C30 +#define M88E1011_I_PHY_ID 0x01410C20 +#define IGP01E1000_I_PHY_ID 0x02A80380 +#define M88E1011_I_REV_4 0x04 +#define M88E1111_I_PHY_ID 0x01410CC0 +#define GG82563_E_PHY_ID 0x01410CA0 +#define IGP03E1000_E_PHY_ID 0x02A80390 +#define IFE_E_PHY_ID 0x02A80330 +#define IFE_PLUS_E_PHY_ID 0x02A80320 +#define IFE_C_E_PHY_ID 0x02A80310 +#define BME1000_E_PHY_ID 0x01410CB0 +#define BME1000_E_PHY_ID_R2 0x01410CB1 +#define IGP04E1000_E_PHY_ID 0x02A80391 +#define M88_VENDOR 0x0141 + +/* M88E1000 Specific Registers */ +#define M88E1000_PHY_SPEC_CTRL 0x10 /* PHY Specific Control Register */ +#define M88E1000_PHY_SPEC_STATUS 0x11 /* PHY Specific Status Register */ +#define M88E1000_INT_ENABLE 0x12 /* Interrupt Enable Register */ +#define M88E1000_INT_STATUS 0x13 /* Interrupt Status Register */ +#define M88E1000_EXT_PHY_SPEC_CTRL 0x14 /* Extended PHY Specific Control */ +#define M88E1000_RX_ERR_CNTR 0x15 /* Receive Error Counter */ + +#define M88E1000_PHY_EXT_CTRL 0x1A /* PHY extend control register */ +#define M88E1000_PHY_PAGE_SELECT 0x1D /* Reg 29 for page number setting */ +#define M88E1000_PHY_GEN_CONTROL 0x1E /* Its meaning depends on reg 29 */ +#define M88E1000_PHY_VCO_REG_BIT8 0x100 /* Bits 8 & 11 are adjusted for */ +#define M88E1000_PHY_VCO_REG_BIT11 0x800 /* improved BER performance */ + +/* M88E1000 PHY Specific Control Register */ +#define M88E1000_PSCR_JABBER_DISABLE 0x0001 /* 1=Jabber Function disabled */ +#define M88E1000_PSCR_POLARITY_REVERSAL 0x0002 /* 1=Polarity Reversal enabled */ +#define M88E1000_PSCR_SQE_TEST 0x0004 /* 1=SQE Test enabled */ +/* 1=CLK125 low, 0=CLK125 toggling */ +#define M88E1000_PSCR_CLK125_DISABLE 0x0010 +#define M88E1000_PSCR_MDI_MANUAL_MODE 0x0000 /* MDI Crossover Mode bits 6:5 */ + /* Manual MDI configuration */ +#define M88E1000_PSCR_MDIX_MANUAL_MODE 0x0020 /* Manual MDIX configuration */ +/* 1000BASE-T: Auto crossover, 100BASE-TX/10BASE-T: MDI Mode */ +#define M88E1000_PSCR_AUTO_X_1000T 0x0040 +/* Auto crossover enabled all speeds */ +#define M88E1000_PSCR_AUTO_X_MODE 0x0060 +/* + * 1=Enable Extended 10BASE-T distance (Lower 10BASE-T Rx Threshold + * 0=Normal 10BASE-T Rx Threshold + */ +#define M88E1000_PSCR_EN_10BT_EXT_DIST 0x0080 +/* 1=5-bit interface in 100BASE-TX, 0=MII interface in 100BASE-TX */ +#define M88E1000_PSCR_MII_5BIT_ENABLE 0x0100 +#define M88E1000_PSCR_SCRAMBLER_DISABLE 0x0200 /* 1=Scrambler disable */ +#define M88E1000_PSCR_FORCE_LINK_GOOD 0x0400 /* 1=Force link good */ +#define M88E1000_PSCR_ASSERT_CRS_ON_TX 0x0800 /* 1=Assert CRS on Transmit */ + +/* M88E1000 PHY Specific Status Register */ +#define M88E1000_PSSR_JABBER 0x0001 /* 1=Jabber */ +#define M88E1000_PSSR_REV_POLARITY 0x0002 /* 1=Polarity reversed */ +#define M88E1000_PSSR_DOWNSHIFT 0x0020 /* 1=Downshifted */ +#define M88E1000_PSSR_MDIX 0x0040 /* 1=MDIX; 0=MDI */ +/* + * 0 = <50M + * 1 = 50-80M + * 2 = 80-110M + * 3 = 110-140M + * 4 = >140M + */ +#define M88E1000_PSSR_CABLE_LENGTH 0x0380 +#define M88E1000_PSSR_LINK 0x0400 /* 1=Link up, 0=Link down */ +#define M88E1000_PSSR_SPD_DPLX_RESOLVED 0x0800 /* 1=Speed & Duplex resolved */ +#define M88E1000_PSSR_PAGE_RCVD 0x1000 /* 1=Page received */ +#define M88E1000_PSSR_DPLX 0x2000 /* 1=Duplex 0=Half Duplex */ +#define M88E1000_PSSR_SPEED 0xC000 /* Speed, bits 14:15 */ +#define M88E1000_PSSR_10MBS 0x0000 /* 00=10Mbs */ +#define M88E1000_PSSR_100MBS 0x4000 /* 01=100Mbs */ +#define M88E1000_PSSR_1000MBS 0x8000 /* 10=1000Mbs */ + +#define M88E1000_PSSR_CABLE_LENGTH_SHIFT 7 + +/* M88E1000 Extended PHY Specific Control Register */ +#define M88E1000_EPSCR_FIBER_LOOPBACK 0x4000 /* 1=Fiber loopback */ +/* + * 1 = Lost lock detect enabled. + * Will assert lost lock and bring + * link down if idle not seen + * within 1ms in 1000BASE-T + */ +#define M88E1000_EPSCR_DOWN_NO_IDLE 0x8000 +/* + * Number of times we will attempt to autonegotiate before downshifting if we + * are the master + */ +#define M88E1000_EPSCR_MASTER_DOWNSHIFT_MASK 0x0C00 +#define M88E1000_EPSCR_MASTER_DOWNSHIFT_1X 0x0000 +#define M88E1000_EPSCR_MASTER_DOWNSHIFT_2X 0x0400 +#define M88E1000_EPSCR_MASTER_DOWNSHIFT_3X 0x0800 +#define M88E1000_EPSCR_MASTER_DOWNSHIFT_4X 0x0C00 +/* + * Number of times we will attempt to autonegotiate before downshifting if we + * are the slave + */ +#define M88E1000_EPSCR_SLAVE_DOWNSHIFT_MASK 0x0300 +#define M88E1000_EPSCR_SLAVE_DOWNSHIFT_DIS 0x0000 +#define M88E1000_EPSCR_SLAVE_DOWNSHIFT_1X 0x0100 +#define M88E1000_EPSCR_SLAVE_DOWNSHIFT_2X 0x0200 +#define M88E1000_EPSCR_SLAVE_DOWNSHIFT_3X 0x0300 +#define M88E1000_EPSCR_TX_CLK_2_5 0x0060 /* 2.5 MHz TX_CLK */ +#define M88E1000_EPSCR_TX_CLK_25 0x0070 /* 25 MHz TX_CLK */ +#define M88E1000_EPSCR_TX_CLK_0 0x0000 /* NO TX_CLK */ + +/* M88EC018 Rev 2 specific DownShift settings */ +#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_MASK 0x0E00 +#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_1X 0x0000 +#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_2X 0x0200 +#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_3X 0x0400 +#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_4X 0x0600 +#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_5X 0x0800 +#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_6X 0x0A00 +#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_7X 0x0C00 +#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_8X 0x0E00 + +/* BME1000 PHY Specific Control Register */ +#define BME1000_PSCR_ENABLE_DOWNSHIFT 0x0800 /* 1 = enable downshift */ + +/* + * Bits... + * 15-5: page + * 4-0: register offset + */ +#define GG82563_PAGE_SHIFT 5 +#define GG82563_REG(page, reg) \ + (((page) << GG82563_PAGE_SHIFT) | ((reg) & MAX_PHY_REG_ADDRESS)) +#define GG82563_MIN_ALT_REG 30 + +/* GG82563 Specific Registers */ +#define GG82563_PHY_SPEC_CTRL \ + GG82563_REG(0, 16) /* PHY Specific Control */ +#define GG82563_PHY_SPEC_STATUS \ + GG82563_REG(0, 17) /* PHY Specific Status */ +#define GG82563_PHY_INT_ENABLE \ + GG82563_REG(0, 18) /* Interrupt Enable */ +#define GG82563_PHY_SPEC_STATUS_2 \ + GG82563_REG(0, 19) /* PHY Specific Status 2 */ +#define GG82563_PHY_RX_ERR_CNTR \ + GG82563_REG(0, 21) /* Receive Error Counter */ +#define GG82563_PHY_PAGE_SELECT \ + GG82563_REG(0, 22) /* Page Select */ +#define GG82563_PHY_SPEC_CTRL_2 \ + GG82563_REG(0, 26) /* PHY Specific Control 2 */ +#define GG82563_PHY_PAGE_SELECT_ALT \ + GG82563_REG(0, 29) /* Alternate Page Select */ +#define GG82563_PHY_TEST_CLK_CTRL \ + GG82563_REG(0, 30) /* Test Clock Control (use reg. 29 to select) */ + +#define GG82563_PHY_MAC_SPEC_CTRL \ + GG82563_REG(2, 21) /* MAC Specific Control Register */ +#define GG82563_PHY_MAC_SPEC_CTRL_2 \ + GG82563_REG(2, 26) /* MAC Specific Control 2 */ + +#define GG82563_PHY_DSP_DISTANCE \ + GG82563_REG(5, 26) /* DSP Distance */ + +/* Page 193 - Port Control Registers */ +#define GG82563_PHY_KMRN_MODE_CTRL \ + GG82563_REG(193, 16) /* Kumeran Mode Control */ +#define GG82563_PHY_PORT_RESET \ + GG82563_REG(193, 17) /* Port Reset */ +#define GG82563_PHY_REVISION_ID \ + GG82563_REG(193, 18) /* Revision ID */ +#define GG82563_PHY_DEVICE_ID \ + GG82563_REG(193, 19) /* Device ID */ +#define GG82563_PHY_PWR_MGMT_CTRL \ + GG82563_REG(193, 20) /* Power Management Control */ +#define GG82563_PHY_RATE_ADAPT_CTRL \ + GG82563_REG(193, 25) /* Rate Adaptation Control */ + +/* Page 194 - KMRN Registers */ +#define GG82563_PHY_KMRN_FIFO_CTRL_STAT \ + GG82563_REG(194, 16) /* FIFO's Control/Status */ +#define GG82563_PHY_KMRN_CTRL \ + GG82563_REG(194, 17) /* Control */ +#define GG82563_PHY_INBAND_CTRL \ + GG82563_REG(194, 18) /* Inband Control */ +#define GG82563_PHY_KMRN_DIAGNOSTIC \ + GG82563_REG(194, 19) /* Diagnostic */ +#define GG82563_PHY_ACK_TIMEOUTS \ + GG82563_REG(194, 20) /* Acknowledge Timeouts */ +#define GG82563_PHY_ADV_ABILITY \ + GG82563_REG(194, 21) /* Advertised Ability */ +#define GG82563_PHY_LINK_PARTNER_ADV_ABILITY \ + GG82563_REG(194, 23) /* Link Partner Advertised Ability */ +#define GG82563_PHY_ADV_NEXT_PAGE \ + GG82563_REG(194, 24) /* Advertised Next Page */ +#define GG82563_PHY_LINK_PARTNER_ADV_NEXT_PAGE \ + GG82563_REG(194, 25) /* Link Partner Advertised Next page */ +#define GG82563_PHY_KMRN_MISC \ + GG82563_REG(194, 26) /* Misc. */ + +/* MDI Control */ +#define E1000_MDIC_DATA_MASK 0x0000FFFF +#define E1000_MDIC_REG_MASK 0x001F0000 +#define E1000_MDIC_REG_SHIFT 16 +#define E1000_MDIC_PHY_MASK 0x03E00000 +#define E1000_MDIC_PHY_SHIFT 21 +#define E1000_MDIC_OP_WRITE 0x04000000 +#define E1000_MDIC_OP_READ 0x08000000 +#define E1000_MDIC_READY 0x10000000 +#define E1000_MDIC_INT_EN 0x20000000 +#define E1000_MDIC_ERROR 0x40000000 + +/* SerDes Control */ +#define E1000_GEN_CTL_READY 0x80000000 +#define E1000_GEN_CTL_ADDRESS_SHIFT 8 +#define E1000_GEN_POLL_TIMEOUT 640 + +/* LinkSec register fields */ +#define E1000_LSECTXCAP_SUM_MASK 0x00FF0000 +#define E1000_LSECTXCAP_SUM_SHIFT 16 +#define E1000_LSECRXCAP_SUM_MASK 0x00FF0000 +#define E1000_LSECRXCAP_SUM_SHIFT 16 + +#define E1000_LSECTXCTRL_EN_MASK 0x00000003 +#define E1000_LSECTXCTRL_DISABLE 0x0 +#define E1000_LSECTXCTRL_AUTH 0x1 +#define E1000_LSECTXCTRL_AUTH_ENCRYPT 0x2 +#define E1000_LSECTXCTRL_AISCI 0x00000020 +#define E1000_LSECTXCTRL_PNTHRSH_MASK 0xFFFFFF00 +#define E1000_LSECTXCTRL_RSV_MASK 0x000000D8 + +#define E1000_LSECRXCTRL_EN_MASK 0x0000000C +#define E1000_LSECRXCTRL_EN_SHIFT 2 +#define E1000_LSECRXCTRL_DISABLE 0x0 +#define E1000_LSECRXCTRL_CHECK 0x1 +#define E1000_LSECRXCTRL_STRICT 0x2 +#define E1000_LSECRXCTRL_DROP 0x3 +#define E1000_LSECRXCTRL_PLSH 0x00000040 +#define E1000_LSECRXCTRL_RP 0x00000080 +#define E1000_LSECRXCTRL_RSV_MASK 0xFFFFFF33 + +#endif /* _E1000_DEFINES_H_ */ diff --git a/sys/dev/netif/ig_hal/e1000_hw.h b/sys/dev/netif/ig_hal/e1000_hw.h new file mode 100644 index 0000000000..277d8d1192 --- /dev/null +++ b/sys/dev/netif/ig_hal/e1000_hw.h @@ -0,0 +1,840 @@ +/****************************************************************************** + + Copyright (c) 2001-2008, Intel Corporation + All rights reserved. + + Redistribution and use in source and binary forms, with or without + modification, are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, + this list of conditions and the following disclaimer. + + 2. Redistributions in binary form must reproduce the above copyright + notice, this list of conditions and the following disclaimer in the + documentation and/or other materials provided with the distribution. + + 3. Neither the name of the Intel Corporation nor the names of its + contributors may be used to endorse or promote products derived from + this software without specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE + ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE + LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR + CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF + SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS + INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN + CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) + ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + POSSIBILITY OF SUCH DAMAGE. + +******************************************************************************/ +/*$FreeBSD$*/ + +#ifndef _E1000_HW_H_ +#define _E1000_HW_H_ + +#include "e1000_osdep.h" +#include "e1000_regs.h" +#include "e1000_defines.h" + +struct e1000_hw; + +#define E1000_DEV_ID_82542 0x1000 +#define E1000_DEV_ID_82543GC_FIBER 0x1001 +#define E1000_DEV_ID_82543GC_COPPER 0x1004 +#define E1000_DEV_ID_82544EI_COPPER 0x1008 +#define E1000_DEV_ID_82544EI_FIBER 0x1009 +#define E1000_DEV_ID_82544GC_COPPER 0x100C +#define E1000_DEV_ID_82544GC_LOM 0x100D +#define E1000_DEV_ID_82540EM 0x100E +#define E1000_DEV_ID_82540EM_LOM 0x1015 +#define E1000_DEV_ID_82540EP_LOM 0x1016 +#define E1000_DEV_ID_82540EP 0x1017 +#define E1000_DEV_ID_82540EP_LP 0x101E +#define E1000_DEV_ID_82545EM_COPPER 0x100F +#define E1000_DEV_ID_82545EM_FIBER 0x1011 +#define E1000_DEV_ID_82545GM_COPPER 0x1026 +#define E1000_DEV_ID_82545GM_FIBER 0x1027 +#define E1000_DEV_ID_82545GM_SERDES 0x1028 +#define E1000_DEV_ID_82546EB_COPPER 0x1010 +#define E1000_DEV_ID_82546EB_FIBER 0x1012 +#define E1000_DEV_ID_82546EB_QUAD_COPPER 0x101D +#define E1000_DEV_ID_82546GB_COPPER 0x1079 +#define E1000_DEV_ID_82546GB_FIBER 0x107A +#define E1000_DEV_ID_82546GB_SERDES 0x107B +#define E1000_DEV_ID_82546GB_PCIE 0x108A +#define E1000_DEV_ID_82546GB_QUAD_COPPER 0x1099 +#define E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3 0x10B5 +#define E1000_DEV_ID_82541EI 0x1013 +#define E1000_DEV_ID_82541EI_MOBILE 0x1018 +#define E1000_DEV_ID_82541ER_LOM 0x1014 +#define E1000_DEV_ID_82541ER 0x1078 +#define E1000_DEV_ID_82541GI 0x1076 +#define E1000_DEV_ID_82541GI_LF 0x107C +#define E1000_DEV_ID_82541GI_MOBILE 0x1077 +#define E1000_DEV_ID_82547EI 0x1019 +#define E1000_DEV_ID_82547EI_MOBILE 0x101A +#define E1000_DEV_ID_82547GI 0x1075 +#define E1000_DEV_ID_82571EB_COPPER 0x105E +#define E1000_DEV_ID_82571EB_FIBER 0x105F +#define E1000_DEV_ID_82571EB_SERDES 0x1060 +#define E1000_DEV_ID_82571EB_SERDES_DUAL 0x10D9 +#define E1000_DEV_ID_82571EB_SERDES_QUAD 0x10DA +#define E1000_DEV_ID_82571EB_QUAD_COPPER 0x10A4 +#define E1000_DEV_ID_82571PT_QUAD_COPPER 0x10D5 +#define E1000_DEV_ID_82571EB_QUAD_FIBER 0x10A5 +#define E1000_DEV_ID_82571EB_QUAD_COPPER_LP 0x10BC +#define E1000_DEV_ID_82572EI_COPPER 0x107D +#define E1000_DEV_ID_82572EI_FIBER 0x107E +#define E1000_DEV_ID_82572EI_SERDES 0x107F +#define E1000_DEV_ID_82572EI 0x10B9 +#define E1000_DEV_ID_82573E 0x108B +#define E1000_DEV_ID_82573E_IAMT 0x108C +#define E1000_DEV_ID_82573L 0x109A +#define E1000_DEV_ID_82574L 0x10D3 +#define E1000_DEV_ID_80003ES2LAN_COPPER_DPT 0x1096 +#define E1000_DEV_ID_80003ES2LAN_SERDES_DPT 0x1098 +#define E1000_DEV_ID_80003ES2LAN_COPPER_SPT 0x10BA +#define E1000_DEV_ID_80003ES2LAN_SERDES_SPT 0x10BB +#define E1000_DEV_ID_ICH8_IGP_M_AMT 0x1049 +#define E1000_DEV_ID_ICH8_IGP_AMT 0x104A +#define E1000_DEV_ID_ICH8_IGP_C 0x104B +#define E1000_DEV_ID_ICH8_IFE 0x104C +#define E1000_DEV_ID_ICH8_IFE_GT 0x10C4 +#define E1000_DEV_ID_ICH8_IFE_G 0x10C5 +#define E1000_DEV_ID_ICH8_IGP_M 0x104D +#define E1000_DEV_ID_ICH9_IGP_M 0x10BF +#define E1000_DEV_ID_ICH9_IGP_M_AMT 0x10F5 +#define E1000_DEV_ID_ICH9_IGP_M_V 0x10CB +#define E1000_DEV_ID_ICH9_IGP_AMT 0x10BD +#define E1000_DEV_ID_ICH9_BM 0x10E5 +#define E1000_DEV_ID_ICH9_IGP_C 0x294C +#define E1000_DEV_ID_ICH9_IFE 0x10C0 +#define E1000_DEV_ID_ICH9_IFE_GT 0x10C3 +#define E1000_DEV_ID_ICH9_IFE_G 0x10C2 +#define E1000_DEV_ID_ICH10_R_BM_LM 0x10CC +#define E1000_DEV_ID_ICH10_R_BM_LF 0x10CD +#define E1000_DEV_ID_ICH10_R_BM_V 0x10CE +#define E1000_DEV_ID_ICH10_D_BM_LM 0x10DE +#define E1000_DEV_ID_ICH10_D_BM_LF 0x10DF +#define E1000_DEV_ID_82576 0x10C9 +#define E1000_DEV_ID_82576_FIBER 0x10E6 +#define E1000_DEV_ID_82576_SERDES 0x10E7 +#define E1000_DEV_ID_82576_QUAD_COPPER 0x10E8 +#define E1000_DEV_ID_82576_VF 0x10CA +#define E1000_DEV_ID_82575EB_COPPER 0x10A7 +#define E1000_DEV_ID_82575EB_FIBER_SERDES 0x10A9 +#define E1000_DEV_ID_82575GB_QUAD_COPPER 0x10D6 +#define E1000_REVISION_0 0 +#define E1000_REVISION_1 1 +#define E1000_REVISION_2 2 +#define E1000_REVISION_3 3 +#define E1000_REVISION_4 4 + +#define E1000_FUNC_0 0 +#define E1000_FUNC_1 1 + +enum e1000_mac_type { + e1000_undefined = 0, + e1000_82542, + e1000_82543, + e1000_82544, + e1000_82540, + e1000_82545, + e1000_82545_rev_3, + e1000_82546, + e1000_82546_rev_3, + e1000_82541, + e1000_82541_rev_2, + e1000_82547, + e1000_82547_rev_2, + e1000_82571, + e1000_82572, + e1000_82573, + e1000_82574, + e1000_80003es2lan, + e1000_ich8lan, + e1000_ich9lan, + e1000_ich10lan, + e1000_82575, + e1000_82576, + e1000_vfadapt, + e1000_num_macs /* List is 1-based, so subtract 1 for TRUE count. */ +}; + +enum e1000_media_type { + e1000_media_type_unknown = 0, + e1000_media_type_copper = 1, + e1000_media_type_fiber = 2, + e1000_media_type_internal_serdes = 3, + e1000_num_media_types +}; + +enum e1000_nvm_type { + e1000_nvm_unknown = 0, + e1000_nvm_none, + e1000_nvm_eeprom_spi, + e1000_nvm_eeprom_microwire, + e1000_nvm_flash_hw, + e1000_nvm_flash_sw +}; + +enum e1000_nvm_override { + e1000_nvm_override_none = 0, + e1000_nvm_override_spi_small, + e1000_nvm_override_spi_large, + e1000_nvm_override_microwire_small, + e1000_nvm_override_microwire_large +}; + +enum e1000_phy_type { + e1000_phy_unknown = 0, + e1000_phy_none, + e1000_phy_m88, + e1000_phy_igp, + e1000_phy_igp_2, + e1000_phy_gg82563, + e1000_phy_igp_3, + e1000_phy_ife, + e1000_phy_bm, + e1000_phy_vf, +}; + +enum e1000_bus_type { + e1000_bus_type_unknown = 0, + e1000_bus_type_pci, + e1000_bus_type_pcix, + e1000_bus_type_pci_express, + e1000_bus_type_reserved +}; + +enum e1000_bus_speed { + e1000_bus_speed_unknown = 0, + e1000_bus_speed_33, + e1000_bus_speed_66, + e1000_bus_speed_100, + e1000_bus_speed_120, + e1000_bus_speed_133, + e1000_bus_speed_2500, + e1000_bus_speed_5000, + e1000_bus_speed_reserved +}; + +enum e1000_bus_width { + e1000_bus_width_unknown = 0, + e1000_bus_width_pcie_x1, + e1000_bus_width_pcie_x2, + e1000_bus_width_pcie_x4 = 4, + e1000_bus_width_pcie_x8 = 8, + e1000_bus_width_32, + e1000_bus_width_64, + e1000_bus_width_reserved +}; + +enum e1000_1000t_rx_status { + e1000_1000t_rx_status_not_ok = 0, + e1000_1000t_rx_status_ok, + e1000_1000t_rx_status_undefined = 0xFF +}; + +enum e1000_rev_polarity { + e1000_rev_polarity_normal = 0, + e1000_rev_polarity_reversed, + e1000_rev_polarity_undefined = 0xFF +}; + +enum e1000_fc_mode { + e1000_fc_none = 0, + e1000_fc_rx_pause, + e1000_fc_tx_pause, + e1000_fc_full, + e1000_fc_default = 0xFF +}; + +enum e1000_ffe_config { + e1000_ffe_config_enabled = 0, + e1000_ffe_config_active, + e1000_ffe_config_blocked +}; + +enum e1000_dsp_config { + e1000_dsp_config_disabled = 0, + e1000_dsp_config_enabled, + e1000_dsp_config_activated, + e1000_dsp_config_undefined = 0xFF +}; + +enum e1000_ms_type { + e1000_ms_hw_default = 0, + e1000_ms_force_master, + e1000_ms_force_slave, + e1000_ms_auto +}; + +enum e1000_smart_speed { + e1000_smart_speed_default = 0, + e1000_smart_speed_on, + e1000_smart_speed_off +}; + +/* Receive Descriptor */ +struct e1000_rx_desc { + __le64 buffer_addr; /* Address of the descriptor's data buffer */ + __le16 length; /* Length of data DMAed into data buffer */ + __le16 csum; /* Packet checksum */ + u8 status; /* Descriptor status */ + u8 errors; /* Descriptor Errors */ + __le16 special; +}; + +/* Receive Descriptor - Extended */ +union e1000_rx_desc_extended { + struct { + __le64 buffer_addr; + __le64 reserved; + } read; + struct { + struct { + __le32 mrq; /* Multiple Rx Queues */ + union { + __le32 rss; /* RSS Hash */ + struct { + __le16 ip_id; /* IP id */ + __le16 csum; /* Packet Checksum */ + } csum_ip; + } hi_dword; + } lower; + struct { + __le32 status_error; /* ext status/error */ + __le16 length; + __le16 vlan; /* VLAN tag */ + } upper; + } wb; /* writeback */ +}; + +#define MAX_PS_BUFFERS 4 +/* Receive Descriptor - Packet Split */ +union e1000_rx_desc_packet_split { + struct { + /* one buffer for protocol header(s), three data buffers */ + __le64 buffer_addr[MAX_PS_BUFFERS]; + } read; + struct { + struct { + __le32 mrq; /* Multiple Rx Queues */ + union { + __le32 rss; /* RSS Hash */ + struct { + __le16 ip_id; /* IP id */ + __le16 csum; /* Packet Checksum */ + } csum_ip; + } hi_dword; + } lower; + struct { + __le32 status_error; /* ext status/error */ + __le16 length0; /* length of buffer 0 */ + __le16 vlan; /* VLAN tag */ + } middle; + struct { + __le16 header_status; + __le16 length[3]; /* length of buffers 1-3 */ + } upper; + __le64 reserved; + } wb; /* writeback */ +}; + +/* Transmit Descriptor */ +struct e1000_tx_desc { + __le64 buffer_addr; /* Address of the descriptor's data buffer */ + union { + __le32 data; + struct { + __le16 length; /* Data buffer length */ + u8 cso; /* Checksum offset */ + u8 cmd; /* Descriptor control */ + } flags; + } lower; + union { + __le32 data; + struct { + u8 status; /* Descriptor status */ + u8 css; /* Checksum start */ + __le16 special; + } fields; + } upper; +}; + +/* Offload Context Descriptor */ +struct e1000_context_desc { + union { + __le32 ip_config; + struct { + u8 ipcss; /* IP checksum start */ + u8 ipcso; /* IP checksum offset */ + __le16 ipcse; /* IP checksum end */ + } ip_fields; + } lower_setup; + union { + __le32 tcp_config; + struct { + u8 tucss; /* TCP checksum start */ + u8 tucso; /* TCP checksum offset */ + __le16 tucse; /* TCP checksum end */ + } tcp_fields; + } upper_setup; + __le32 cmd_and_length; + union { + __le32 data; + struct { + u8 status; /* Descriptor status */ + u8 hdr_len; /* Header length */ + __le16 mss; /* Maximum segment size */ + } fields; + } tcp_seg_setup; +}; + +/* Offload data descriptor */ +struct e1000_data_desc { + __le64 buffer_addr; /* Address of the descriptor's buffer address */ + union { + __le32 data; + struct { + __le16 length; /* Data buffer length */ + u8 typ_len_ext; + u8 cmd; + } flags; + } lower; + union { + __le32 data; + struct { + u8 status; /* Descriptor status */ + u8 popts; /* Packet Options */ + __le16 special; + } fields; + } upper; +}; + +/* Statistics counters collected by the MAC */ +struct e1000_hw_stats { + u64 crcerrs; + u64 algnerrc; + u64 symerrs; + u64 rxerrc; + u64 mpc; + u64 scc; + u64 ecol; + u64 mcc; + u64 latecol; + u64 colc; + u64 dc; + u64 tncrs; + u64 sec; + u64 cexterr; + u64 rlec; + u64 xonrxc; + u64 xontxc; + u64 xoffrxc; + u64 xofftxc; + u64 fcruc; + u64 prc64; + u64 prc127; + u64 prc255; + u64 prc511; + u64 prc1023; + u64 prc1522; + u64 gprc; + u64 bprc; + u64 mprc; + u64 gptc; + u64 gorc; + u64 gotc; + u64 rnbc; + u64 ruc; + u64 rfc; + u64 roc; + u64 rjc; + u64 mgprc; + u64 mgpdc; + u64 mgptc; + u64 tor; + u64 tot; + u64 tpr; + u64 tpt; + u64 ptc64; + u64 ptc127; + u64 ptc255; + u64 ptc511; + u64 ptc1023; + u64 ptc1522; + u64 mptc; + u64 bptc; + u64 tsctc; + u64 tsctfc; + u64 iac; + u64 icrxptc; + u64 icrxatc; + u64 ictxptc; + u64 ictxatc; + u64 ictxqec; + u64 ictxqmtc; + u64 icrxdmtc; + u64 icrxoc; + u64 cbtmpc; + u64 htdpmc; + u64 cbrdpc; + u64 cbrmpc; + u64 rpthc; + u64 hgptc; + u64 htcbdpc; + u64 hgorc; + u64 hgotc; + u64 lenerrs; + u64 scvpc; + u64 hrmpc; + u64 doosync; +}; + +struct e1000_vf_stats { + u64 base_gprc; + u64 base_gptc; + u64 base_gorc; + u64 base_gotc; + u64 base_mprc; + u64 base_gotlbc; + u64 base_gptlbc; + u64 base_gorlbc; + u64 base_gprlbc; + + u32 last_gprc; + u32 last_gptc; + u32 last_gorc; + u32 last_gotc; + u32 last_mprc; + u32 last_gotlbc; + u32 last_gptlbc; + u32 last_gorlbc; + u32 last_gprlbc; + + u64 gprc; + u64 gptc; + u64 gorc; + u64 gotc; + u64 mprc; + u64 gotlbc; + u64 gptlbc; + u64 gorlbc; + u64 gprlbc; +}; + +struct e1000_phy_stats { + u32 idle_errors; + u32 receive_errors; +}; + +struct e1000_host_mng_dhcp_cookie { + u32 signature; + u8 status; + u8 reserved0; + u16 vlan_id; + u32 reserved1; + u16 reserved2; + u8 reserved3; + u8 checksum; +}; + +/* Host Interface "Rev 1" */ +struct e1000_host_command_header { + u8 command_id; + u8 command_length; + u8 command_options; + u8 checksum; +}; + +#define E1000_HI_MAX_DATA_LENGTH 252 +struct e1000_host_command_info { + struct e1000_host_command_header command_header; + u8 command_data[E1000_HI_MAX_DATA_LENGTH]; +}; + +/* Host Interface "Rev 2" */ +struct e1000_host_mng_command_header { + u8 command_id; + u8 checksum; + u16 reserved1; + u16 reserved2; + u16 command_length; +}; + +#define E1000_HI_MAX_MNG_DATA_LENGTH 0x6F8 +struct e1000_host_mng_command_info { + struct e1000_host_mng_command_header command_header; + u8 command_data[E1000_HI_MAX_MNG_DATA_LENGTH]; +}; + +#include "e1000_mac.h" +#include "e1000_phy.h" +#include "e1000_nvm.h" +#include "e1000_manage.h" + +struct e1000_mac_operations { + /* Function pointers for the MAC. */ + s32 (*init_params)(struct e1000_hw *); + s32 (*blink_led)(struct e1000_hw *); + s32 (*check_for_link)(struct e1000_hw *); + bool (*check_mng_mode)(struct e1000_hw *hw); + s32 (*cleanup_led)(struct e1000_hw *); + void (*clear_hw_cntrs)(struct e1000_hw *); + void (*clear_vfta)(struct e1000_hw *); + s32 (*get_bus_info)(struct e1000_hw *); + void (*set_lan_id)(struct e1000_hw *); + s32 (*get_link_up_info)(struct e1000_hw *, u16 *, u16 *); + s32 (*led_on)(struct e1000_hw *); + s32 (*led_off)(struct e1000_hw *); + void (*update_mc_addr_list)(struct e1000_hw *, u8 *, u32, u32, u32); + s32 (*reset_hw)(struct e1000_hw *); + s32 (*init_hw)(struct e1000_hw *); + void (*shutdown_serdes)(struct e1000_hw *); + s32 (*setup_link)(struct e1000_hw *); + s32 (*setup_physical_interface)(struct e1000_hw *); + s32 (*setup_led)(struct e1000_hw *); + void (*write_vfta)(struct e1000_hw *, u32, u32); + void (*mta_set)(struct e1000_hw *, u32); + void (*config_collision_dist)(struct e1000_hw *); + void (*rar_set)(struct e1000_hw *, u8*, u32); + s32 (*read_mac_addr)(struct e1000_hw *); + s32 (*validate_mdi_setting)(struct e1000_hw *); + s32 (*mng_host_if_write)(struct e1000_hw *, u8*, u16, u16, u8*); + s32 (*mng_write_cmd_header)(struct e1000_hw *hw, + struct e1000_host_mng_command_header*); + s32 (*mng_enable_host_if)(struct e1000_hw *); + s32 (*wait_autoneg)(struct e1000_hw *); +}; + +struct e1000_phy_operations { + s32 (*init_params)(struct e1000_hw *); + s32 (*acquire)(struct e1000_hw *); + s32 (*cfg_on_link_up)(struct e1000_hw *); + s32 (*check_polarity)(struct e1000_hw *); + s32 (*check_reset_block)(struct e1000_hw *); + s32 (*commit)(struct e1000_hw *); + s32 (*force_speed_duplex)(struct e1000_hw *); + s32 (*get_cfg_done)(struct e1000_hw *hw); + s32 (*get_cable_length)(struct e1000_hw *); + s32 (*get_info)(struct e1000_hw *); + s32 (*read_reg)(struct e1000_hw *, u32, u16 *); + void (*release)(struct e1000_hw *); + s32 (*reset)(struct e1000_hw *); + s32 (*set_d0_lplu_state)(struct e1000_hw *, bool); + s32 (*set_d3_lplu_state)(struct e1000_hw *, bool); + s32 (*write_reg)(struct e1000_hw *, u32, u16); + void (*power_up)(struct e1000_hw *); + void (*power_down)(struct e1000_hw *); +}; + +struct e1000_nvm_operations { + s32 (*init_params)(struct e1000_hw *); + s32 (*acquire)(struct e1000_hw *); + s32 (*read)(struct e1000_hw *, u16, u16, u16 *); + void (*release)(struct e1000_hw *); + void (*reload)(struct e1000_hw *); + s32 (*update)(struct e1000_hw *); + s32 (*valid_led_default)(struct e1000_hw *, u16 *); + s32 (*validate)(struct e1000_hw *); + s32 (*write)(struct e1000_hw *, u16, u16, u16 *); +}; + +struct e1000_mac_info { + struct e1000_mac_operations ops; + u8 addr[6]; + u8 perm_addr[6]; + + enum e1000_mac_type type; + + u32 collision_delta; + u32 ledctl_default; + u32 ledctl_mode1; + u32 ledctl_mode2; + u32 mc_filter_type; + u32 tx_packet_delta; + u32 txcw; + + u16 current_ifs_val; + u16 ifs_max_val; + u16 ifs_min_val; + u16 ifs_ratio; + u16 ifs_step_size; + u16 mta_reg_count; + u16 rar_entry_count; + + u8 forced_speed_duplex; + + bool adaptive_ifs; + bool arc_subsystem_valid; + bool asf_firmware_present; + bool autoneg; + bool autoneg_failed; + bool get_link_status; + bool in_ifs_mode; + bool report_tx_early; + bool serdes_has_link; + bool tx_pkt_filtering; +}; + +struct e1000_phy_info { + struct e1000_phy_operations ops; + enum e1000_phy_type type; + + enum e1000_1000t_rx_status local_rx; + enum e1000_1000t_rx_status remote_rx; + enum e1000_ms_type ms_type; + enum e1000_ms_type original_ms_type; + enum e1000_rev_polarity cable_polarity; + enum e1000_smart_speed smart_speed; + + u32 addr; + u32 id; + u32 reset_delay_us; /* in usec */ + u32 revision; + + enum e1000_media_type media_type; + + u16 autoneg_advertised; + u16 autoneg_mask; + u16 cable_length; + u16 max_cable_length; + u16 min_cable_length; + + u8 mdix; + + bool disable_polarity_correction; + bool is_mdix; + bool polarity_correction; + bool reset_disable; + bool speed_downgraded; + bool autoneg_wait_to_complete; +}; + +struct e1000_nvm_info { + struct e1000_nvm_operations ops; + enum e1000_nvm_type type; + enum e1000_nvm_override override; + + u32 flash_bank_size; + u32 flash_base_addr; + + u16 word_size; + u16 delay_usec; + u16 address_bits; + u16 opcode_bits; + u16 page_size; +}; + +struct e1000_bus_info { + enum e1000_bus_type type; + enum e1000_bus_speed speed; + enum e1000_bus_width width; + + u16 func; + u16 pci_cmd_word; +}; + +struct e1000_fc_info { + u32 high_water; /* Flow control high-water mark */ + u32 low_water; /* Flow control low-water mark */ + u16 pause_time; /* Flow control pause timer */ + bool send_xon; /* Flow control send XON */ + bool strict_ieee; /* Strict IEEE mode */ + enum e1000_fc_mode current_mode; /* FC mode in effect */ + enum e1000_fc_mode requested_mode; /* FC mode requested by caller */ +}; + +struct e1000_dev_spec_82541 { + enum e1000_dsp_config dsp_config; + enum e1000_ffe_config ffe_config; + u16 spd_default; + bool phy_init_script; +}; + +struct e1000_dev_spec_82542 { + bool dma_fairness; +}; + +struct e1000_dev_spec_82543 { + u32 tbi_compatibility; + bool dma_fairness; + bool init_phy_disabled; +}; + +struct e1000_dev_spec_82571 { + bool laa_is_present; +}; + +struct e1000_shadow_ram { + u16 value; + bool modified; +}; + +#define E1000_SHADOW_RAM_WORDS 2048 + +struct e1000_dev_spec_ich8lan { + bool kmrn_lock_loss_workaround_enabled; + struct e1000_shadow_ram shadow_ram[E1000_SHADOW_RAM_WORDS]; +}; + +struct e1000_dev_spec_82575 { + bool sgmii_active; +}; + +struct e1000_dev_spec_vf { + u32 vf_number; +}; + +struct e1000_hw { + void *back; + + u8 *hw_addr; + u8 *flash_address; + unsigned long io_base; + + struct e1000_mac_info mac; + struct e1000_fc_info fc; + struct e1000_phy_info phy; + struct e1000_nvm_info nvm; + struct e1000_bus_info bus; + struct e1000_host_mng_dhcp_cookie mng_cookie; + + union { + struct e1000_dev_spec_82541 _82541; + struct e1000_dev_spec_82542 _82542; + struct e1000_dev_spec_82543 _82543; + struct e1000_dev_spec_82571 _82571; + struct e1000_dev_spec_ich8lan ich8lan; + struct e1000_dev_spec_82575 _82575; + struct e1000_dev_spec_vf vf; + } dev_spec; + + u16 device_id; + u16 subsystem_vendor_id; + u16 subsystem_device_id; + u16 vendor_id; + + u8 revision_id; +}; + +#include "e1000_82541.h" +#include "e1000_82543.h" +#include "e1000_82571.h" +#include "e1000_80003es2lan.h" +#include "e1000_ich8lan.h" +#include "e1000_82575.h" + +/* These functions must be implemented by drivers */ +void e1000_pci_clear_mwi(struct e1000_hw *hw); +void e1000_pci_set_mwi(struct e1000_hw *hw); +s32 e1000_read_pcie_cap_reg(struct e1000_hw *hw, u32 reg, u16 *value); +void e1000_read_pci_cfg(struct e1000_hw *hw, u32 reg, u16 *value); +void e1000_write_pci_cfg(struct e1000_hw *hw, u32 reg, u16 *value); + +#endif diff --git a/sys/dev/netif/ig_hal/e1000_ich8lan.c b/sys/dev/netif/ig_hal/e1000_ich8lan.c new file mode 100644 index 0000000000..f36899875a --- /dev/null +++ b/sys/dev/netif/ig_hal/e1000_ich8lan.c @@ -0,0 +1,2638 @@ +/****************************************************************************** + + Copyright (c) 2001-2008, Intel Corporation + All rights reserved. + + Redistribution and use in source and binary forms, with or without + modification, are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, + this list of conditions and the following disclaimer. + + 2. Redistributions in binary form must reproduce the above copyright + notice, this list of conditions and the following disclaimer in the + documentation and/or other materials provided with the distribution. + + 3. Neither the name of the Intel Corporation nor the names of its + contributors may be used to endorse or promote products derived from + this software without specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE + ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE + LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR + CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF + SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS + INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN + CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) + ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + POSSIBILITY OF SUCH DAMAGE. + +******************************************************************************/ +/*$FreeBSD$*/ + +/* + * 82562G 10/100 Network Connection + * 82562G-2 10/100 Network Connection + * 82562GT 10/100 Network Connection + * 82562GT-2 10/100 Network Connection + * 82562V 10/100 Network Connection + * 82562V-2 10/100 Network Connection + * 82566DC-2 Gigabit Network Connection + * 82566DC Gigabit Network Connection + * 82566DM-2 Gigabit Network Connection + * 82566DM Gigabit Network Connection + * 82566MC Gigabit Network Connection + * 82566MM Gigabit Network Connection + * 82567LM Gigabit Network Connection + * 82567LF Gigabit Network Connection + * 82567V Gigabit Network Connection + * 82567LM-2 Gigabit Network Connection + * 82567LF-2 Gigabit Network Connection + * 82567V-2 Gigabit Network Connection + * 82567LF-3 Gigabit Network Connection + * 82567LM-3 Gigabit Network Connection + * 82567LM-4 Gigabit Network Connection + */ + +#include "e1000_api.h" + +static s32 e1000_init_phy_params_ich8lan(struct e1000_hw *hw); +static s32 e1000_init_nvm_params_ich8lan(struct e1000_hw *hw); +static s32 e1000_init_mac_params_ich8lan(struct e1000_hw *hw); +static s32 e1000_acquire_swflag_ich8lan(struct e1000_hw *hw); +static void e1000_release_swflag_ich8lan(struct e1000_hw *hw); +static bool e1000_check_mng_mode_ich8lan(struct e1000_hw *hw); +static s32 e1000_check_polarity_ife_ich8lan(struct e1000_hw *hw); +static s32 e1000_check_reset_block_ich8lan(struct e1000_hw *hw); +static s32 e1000_phy_force_speed_duplex_ich8lan(struct e1000_hw *hw); +static s32 e1000_phy_hw_reset_ich8lan(struct e1000_hw *hw); +static s32 e1000_get_phy_info_ich8lan(struct e1000_hw *hw); +static s32 e1000_set_d0_lplu_state_ich8lan(struct e1000_hw *hw, + bool active); +static s32 e1000_set_d3_lplu_state_ich8lan(struct e1000_hw *hw, + bool active); +static s32 e1000_read_nvm_ich8lan(struct e1000_hw *hw, u16 offset, + u16 words, u16 *data); +static s32 e1000_write_nvm_ich8lan(struct e1000_hw *hw, u16 offset, + u16 words, u16 *data); +static s32 e1000_validate_nvm_checksum_ich8lan(struct e1000_hw *hw); +static s32 e1000_update_nvm_checksum_ich8lan(struct e1000_hw *hw); +static s32 e1000_valid_led_default_ich8lan(struct e1000_hw *hw, + u16 *data); +static s32 e1000_get_bus_info_ich8lan(struct e1000_hw *hw); +static s32 e1000_reset_hw_ich8lan(struct e1000_hw *hw); +static s32 e1000_init_hw_ich8lan(struct e1000_hw *hw); +static s32 e1000_setup_link_ich8lan(struct e1000_hw *hw); +static s32 e1000_setup_copper_link_ich8lan(struct e1000_hw *hw); +static s32 e1000_get_link_up_info_ich8lan(struct e1000_hw *hw, + u16 *speed, u16 *duplex); +static s32 e1000_cleanup_led_ich8lan(struct e1000_hw *hw); +static s32 e1000_led_on_ich8lan(struct e1000_hw *hw); +static s32 e1000_led_off_ich8lan(struct e1000_hw *hw); +static void e1000_clear_hw_cntrs_ich8lan(struct e1000_hw *hw); +static s32 e1000_erase_flash_bank_ich8lan(struct e1000_hw *hw, u32 bank); +static s32 e1000_flash_cycle_ich8lan(struct e1000_hw *hw, u32 timeout); +static s32 e1000_flash_cycle_init_ich8lan(struct e1000_hw *hw); +static s32 e1000_get_phy_info_ife_ich8lan(struct e1000_hw *hw); +static void e1000_initialize_hw_bits_ich8lan(struct e1000_hw *hw); +static s32 e1000_kmrn_lock_loss_workaround_ich8lan(struct e1000_hw *hw); +static s32 e1000_read_flash_byte_ich8lan(struct e1000_hw *hw, + u32 offset, u8 *data); +static s32 e1000_read_flash_data_ich8lan(struct e1000_hw *hw, u32 offset, + u8 size, u16 *data); +static s32 e1000_read_flash_word_ich8lan(struct e1000_hw *hw, + u32 offset, u16 *data); +static s32 e1000_retry_write_flash_byte_ich8lan(struct e1000_hw *hw, + u32 offset, u8 byte); +static s32 e1000_write_flash_byte_ich8lan(struct e1000_hw *hw, + u32 offset, u8 data); +static s32 e1000_write_flash_data_ich8lan(struct e1000_hw *hw, u32 offset, + u8 size, u16 data); +static s32 e1000_get_cfg_done_ich8lan(struct e1000_hw *hw); +static void e1000_power_down_phy_copper_ich8lan(struct e1000_hw *hw); + +/* ICH GbE Flash Hardware Sequencing Flash Status Register bit breakdown */ +/* Offset 04h HSFSTS */ +union ich8_hws_flash_status { + struct ich8_hsfsts { + u16 flcdone :1; /* bit 0 Flash Cycle Done */ + u16 flcerr :1; /* bit 1 Flash Cycle Error */ + u16 dael :1; /* bit 2 Direct Access error Log */ + u16 berasesz :2; /* bit 4:3 Sector Erase Size */ + u16 flcinprog :1; /* bit 5 flash cycle in Progress */ + u16 reserved1 :2; /* bit 13:6 Reserved */ + u16 reserved2 :6; /* bit 13:6 Reserved */ + u16 fldesvalid :1; /* bit 14 Flash Descriptor Valid */ + u16 flockdn :1; /* bit 15 Flash Config Lock-Down */ + } hsf_status; + u16 regval; +}; + +/* ICH GbE Flash Hardware Sequencing Flash control Register bit breakdown */ +/* Offset 06h FLCTL */ +union ich8_hws_flash_ctrl { + struct ich8_hsflctl { + u16 flcgo :1; /* 0 Flash Cycle Go */ + u16 flcycle :2; /* 2:1 Flash Cycle */ + u16 reserved :5; /* 7:3 Reserved */ + u16 fldbcount :2; /* 9:8 Flash Data Byte Count */ + u16 flockdn :6; /* 15:10 Reserved */ + } hsf_ctrl; + u16 regval; +}; + +/* ICH Flash Region Access Permissions */ +union ich8_hws_flash_regacc { + struct ich8_flracc { + u32 grra :8; /* 0:7 GbE region Read Access */ + u32 grwa :8; /* 8:15 GbE region Write Access */ + u32 gmrag :8; /* 23:16 GbE Master Read Access Grant */ + u32 gmwag :8; /* 31:24 GbE Master Write Access Grant */ + } hsf_flregacc; + u16 regval; +}; + +/** + * e1000_init_phy_params_ich8lan - Initialize PHY function pointers + * @hw: pointer to the HW structure + * + * Initialize family-specific PHY parameters and function pointers. + **/ +static s32 e1000_init_phy_params_ich8lan(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val = E1000_SUCCESS; + u16 i = 0; + + DEBUGFUNC("e1000_init_phy_params_ich8lan"); + + phy->addr = 1; + phy->reset_delay_us = 100; + + phy->ops.acquire = e1000_acquire_swflag_ich8lan; + phy->ops.check_polarity = e1000_check_polarity_ife_ich8lan; + phy->ops.check_reset_block = e1000_check_reset_block_ich8lan; + phy->ops.force_speed_duplex = e1000_phy_force_speed_duplex_ich8lan; + phy->ops.get_cable_length = e1000_get_cable_length_igp_2; + phy->ops.get_cfg_done = e1000_get_cfg_done_ich8lan; + phy->ops.get_info = e1000_get_phy_info_ich8lan; + phy->ops.read_reg = e1000_read_phy_reg_igp; + phy->ops.release = e1000_release_swflag_ich8lan; + phy->ops.reset = e1000_phy_hw_reset_ich8lan; + phy->ops.set_d0_lplu_state = e1000_set_d0_lplu_state_ich8lan; + phy->ops.set_d3_lplu_state = e1000_set_d3_lplu_state_ich8lan; + phy->ops.write_reg = e1000_write_phy_reg_igp; + phy->ops.power_up = e1000_power_up_phy_copper; + phy->ops.power_down = e1000_power_down_phy_copper_ich8lan; + + /* + * We may need to do this twice - once for IGP and if that fails, + * we'll set BM func pointers and try again + */ + ret_val = e1000_determine_phy_address(hw); + if (ret_val) { + phy->ops.write_reg = e1000_write_phy_reg_bm; + phy->ops.read_reg = e1000_read_phy_reg_bm; + ret_val = e1000_determine_phy_address(hw); + if (ret_val) { + DEBUGOUT("Cannot determine PHY address. Erroring out\n"); + goto out; + } + } + + phy->id = 0; + while ((e1000_phy_unknown == e1000_get_phy_type_from_id(phy->id)) && + (i++ < 100)) { + msec_delay(1); + ret_val = e1000_get_phy_id(hw); + if (ret_val) + goto out; + } + + /* Verify phy id */ + switch (phy->id) { + case IGP03E1000_E_PHY_ID: + phy->type = e1000_phy_igp_3; + phy->autoneg_mask = AUTONEG_ADVERTISE_SPEED_DEFAULT; + break; + case IFE_E_PHY_ID: + case IFE_PLUS_E_PHY_ID: + case IFE_C_E_PHY_ID: + phy->type = e1000_phy_ife; + phy->autoneg_mask = E1000_ALL_NOT_GIG; + break; + case BME1000_E_PHY_ID: + phy->type = e1000_phy_bm; + phy->autoneg_mask = AUTONEG_ADVERTISE_SPEED_DEFAULT; + phy->ops.read_reg = e1000_read_phy_reg_bm; + phy->ops.write_reg = e1000_write_phy_reg_bm; + phy->ops.commit = e1000_phy_sw_reset_generic; + break; + default: + ret_val = -E1000_ERR_PHY; + goto out; + } + +out: + return ret_val; +} + +/** + * e1000_init_nvm_params_ich8lan - Initialize NVM function pointers + * @hw: pointer to the HW structure + * + * Initialize family-specific NVM parameters and function + * pointers. + **/ +static s32 e1000_init_nvm_params_ich8lan(struct e1000_hw *hw) +{ + struct e1000_nvm_info *nvm = &hw->nvm; + struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan; + u32 gfpreg, sector_base_addr, sector_end_addr; + s32 ret_val = E1000_SUCCESS; + u16 i; + + DEBUGFUNC("e1000_init_nvm_params_ich8lan"); + + /* Can't read flash registers if the register set isn't mapped. */ + if (!hw->flash_address) { + DEBUGOUT("ERROR: Flash registers not mapped\n"); + ret_val = -E1000_ERR_CONFIG; + goto out; + } + + nvm->type = e1000_nvm_flash_sw; + + gfpreg = E1000_READ_FLASH_REG(hw, ICH_FLASH_GFPREG); + + /* + * sector_X_addr is a "sector"-aligned address (4096 bytes) + * Add 1 to sector_end_addr since this sector is included in + * the overall size. + */ + sector_base_addr = gfpreg & FLASH_GFPREG_BASE_MASK; + sector_end_addr = ((gfpreg >> 16) & FLASH_GFPREG_BASE_MASK) + 1; + + /* flash_base_addr is byte-aligned */ + nvm->flash_base_addr = sector_base_addr << FLASH_SECTOR_ADDR_SHIFT; + + /* + * find total size of the NVM, then cut in half since the total + * size represents two separate NVM banks. + */ + nvm->flash_bank_size = (sector_end_addr - sector_base_addr) + << FLASH_SECTOR_ADDR_SHIFT; + nvm->flash_bank_size /= 2; + /* Adjust to word count */ + nvm->flash_bank_size /= sizeof(u16); + + nvm->word_size = E1000_SHADOW_RAM_WORDS; + + /* Clear shadow ram */ + for (i = 0; i < nvm->word_size; i++) { + dev_spec->shadow_ram[i].modified = FALSE; + dev_spec->shadow_ram[i].value = 0xFFFF; + } + + /* Function Pointers */ + nvm->ops.acquire = e1000_acquire_swflag_ich8lan; + nvm->ops.read = e1000_read_nvm_ich8lan; + nvm->ops.release = e1000_release_swflag_ich8lan; + nvm->ops.update = e1000_update_nvm_checksum_ich8lan; + nvm->ops.valid_led_default = e1000_valid_led_default_ich8lan; + nvm->ops.validate = e1000_validate_nvm_checksum_ich8lan; + nvm->ops.write = e1000_write_nvm_ich8lan; + +out: + return ret_val; +} + +/** + * e1000_init_mac_params_ich8lan - Initialize MAC function pointers + * @hw: pointer to the HW structure + * + * Initialize family-specific MAC parameters and function + * pointers. + **/ +static s32 e1000_init_mac_params_ich8lan(struct e1000_hw *hw) +{ + struct e1000_mac_info *mac = &hw->mac; + + DEBUGFUNC("e1000_init_mac_params_ich8lan"); + + /* Set media type function pointer */ + hw->phy.media_type = e1000_media_type_copper; + + /* Set mta register count */ + mac->mta_reg_count = 32; + /* Set rar entry count */ + mac->rar_entry_count = E1000_ICH_RAR_ENTRIES; + if (mac->type == e1000_ich8lan) + mac->rar_entry_count--; + /* Set if part includes ASF firmware */ + mac->asf_firmware_present = TRUE; + /* Set if manageability features are enabled. */ + mac->arc_subsystem_valid = TRUE; + + /* Function pointers */ + + /* bus type/speed/width */ + mac->ops.get_bus_info = e1000_get_bus_info_ich8lan; + /* function id */ + mac->ops.set_lan_id = e1000_set_lan_id_single_port; + /* reset */ + mac->ops.reset_hw = e1000_reset_hw_ich8lan; + /* hw initialization */ + mac->ops.init_hw = e1000_init_hw_ich8lan; + /* link setup */ + mac->ops.setup_link = e1000_setup_link_ich8lan; + /* physical interface setup */ + mac->ops.setup_physical_interface = e1000_setup_copper_link_ich8lan; + /* check for link */ + mac->ops.check_for_link = e1000_check_for_copper_link_generic; + /* check management mode */ + mac->ops.check_mng_mode = e1000_check_mng_mode_ich8lan; + /* link info */ + mac->ops.get_link_up_info = e1000_get_link_up_info_ich8lan; + /* multicast address update */ + mac->ops.update_mc_addr_list = e1000_update_mc_addr_list_generic; + /* setting MTA */ + mac->ops.mta_set = e1000_mta_set_generic; + /* blink LED */ + mac->ops.blink_led = e1000_blink_led_generic; + /* setup LED */ + mac->ops.setup_led = e1000_setup_led_generic; + /* cleanup LED */ + mac->ops.cleanup_led = e1000_cleanup_led_ich8lan; + /* turn on/off LED */ + mac->ops.led_on = e1000_led_on_ich8lan; + mac->ops.led_off = e1000_led_off_ich8lan; + /* clear hardware counters */ + mac->ops.clear_hw_cntrs = e1000_clear_hw_cntrs_ich8lan; + + /* Enable PCS Lock-loss workaround for ICH8 */ + if (mac->type == e1000_ich8lan) + e1000_set_kmrn_lock_loss_workaround_ich8lan(hw, TRUE); + + + return E1000_SUCCESS; +} + +/** + * e1000_init_function_pointers_ich8lan - Initialize ICH8 function pointers + * @hw: pointer to the HW structure + * + * Initialize family-specific function pointers for PHY, MAC, and NVM. + **/ +void e1000_init_function_pointers_ich8lan(struct e1000_hw *hw) +{ + DEBUGFUNC("e1000_init_function_pointers_ich8lan"); + + hw->mac.ops.init_params = e1000_init_mac_params_ich8lan; + hw->nvm.ops.init_params = e1000_init_nvm_params_ich8lan; + hw->phy.ops.init_params = e1000_init_phy_params_ich8lan; +} + +/** + * e1000_acquire_swflag_ich8lan - Acquire software control flag + * @hw: pointer to the HW structure + * + * Acquires the software control flag for performing NVM and PHY + * operations. This is a function pointer entry point only called by + * read/write routines for the PHY and NVM parts. + **/ +static s32 e1000_acquire_swflag_ich8lan(struct e1000_hw *hw) +{ + u32 extcnf_ctrl, timeout = PHY_CFG_TIMEOUT; + s32 ret_val = E1000_SUCCESS; + + DEBUGFUNC("e1000_acquire_swflag_ich8lan"); + + while (timeout) { + extcnf_ctrl = E1000_READ_REG(hw, E1000_EXTCNF_CTRL); + extcnf_ctrl |= E1000_EXTCNF_CTRL_SWFLAG; + E1000_WRITE_REG(hw, E1000_EXTCNF_CTRL, extcnf_ctrl); + + extcnf_ctrl = E1000_READ_REG(hw, E1000_EXTCNF_CTRL); + if (extcnf_ctrl & E1000_EXTCNF_CTRL_SWFLAG) + break; + msec_delay_irq(1); + timeout--; + } + + if (!timeout) { + DEBUGOUT("FW or HW has locked the resource for too long.\n"); + extcnf_ctrl &= ~E1000_EXTCNF_CTRL_SWFLAG; + E1000_WRITE_REG(hw, E1000_EXTCNF_CTRL, extcnf_ctrl); + ret_val = -E1000_ERR_CONFIG; + goto out; + } + +out: + return ret_val; +} + +/** + * e1000_release_swflag_ich8lan - Release software control flag + * @hw: pointer to the HW structure + * + * Releases the software control flag for performing NVM and PHY operations. + * This is a function pointer entry point only called by read/write + * routines for the PHY and NVM parts. + **/ +static void e1000_release_swflag_ich8lan(struct e1000_hw *hw) +{ + u32 extcnf_ctrl; + + DEBUGFUNC("e1000_release_swflag_ich8lan"); + + extcnf_ctrl = E1000_READ_REG(hw, E1000_EXTCNF_CTRL); + extcnf_ctrl &= ~E1000_EXTCNF_CTRL_SWFLAG; + E1000_WRITE_REG(hw, E1000_EXTCNF_CTRL, extcnf_ctrl); + + return; +} + +/** + * e1000_check_mng_mode_ich8lan - Checks management mode + * @hw: pointer to the HW structure + * + * This checks if the adapter has manageability enabled. + * This is a function pointer entry point only called by read/write + * routines for the PHY and NVM parts. + **/ +static bool e1000_check_mng_mode_ich8lan(struct e1000_hw *hw) +{ + u32 fwsm; + + DEBUGFUNC("e1000_check_mng_mode_ich8lan"); + + fwsm = E1000_READ_REG(hw, E1000_FWSM); + + return (fwsm & E1000_FWSM_MODE_MASK) == + (E1000_ICH_MNG_IAMT_MODE << E1000_FWSM_MODE_SHIFT); +} + +/** + * e1000_check_reset_block_ich8lan - Check if PHY reset is blocked + * @hw: pointer to the HW structure + * + * Checks if firmware is blocking the reset of the PHY. + * This is a function pointer entry point only called by + * reset routines. + **/ +static s32 e1000_check_reset_block_ich8lan(struct e1000_hw *hw) +{ + u32 fwsm; + + DEBUGFUNC("e1000_check_reset_block_ich8lan"); + + fwsm = E1000_READ_REG(hw, E1000_FWSM); + + return (fwsm & E1000_ICH_FWSM_RSPCIPHY) ? E1000_SUCCESS + : E1000_BLK_PHY_RESET; +} + +/** + * e1000_phy_force_speed_duplex_ich8lan - Force PHY speed & duplex + * @hw: pointer to the HW structure + * + * Forces the speed and duplex settings of the PHY. + * This is a function pointer entry point only called by + * PHY setup routines. + **/ +static s32 e1000_phy_force_speed_duplex_ich8lan(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val; + u16 data; + bool link; + + DEBUGFUNC("e1000_phy_force_speed_duplex_ich8lan"); + + if (phy->type != e1000_phy_ife) { + ret_val = e1000_phy_force_speed_duplex_igp(hw); + goto out; + } + + ret_val = phy->ops.read_reg(hw, PHY_CONTROL, &data); + if (ret_val) + goto out; + + e1000_phy_force_speed_duplex_setup(hw, &data); + + ret_val = phy->ops.write_reg(hw, PHY_CONTROL, data); + if (ret_val) + goto out; + + /* Disable MDI-X support for 10/100 */ + ret_val = phy->ops.read_reg(hw, IFE_PHY_MDIX_CONTROL, &data); + if (ret_val) + goto out; + + data &= ~IFE_PMC_AUTO_MDIX; + data &= ~IFE_PMC_FORCE_MDIX; + + ret_val = phy->ops.write_reg(hw, IFE_PHY_MDIX_CONTROL, data); + if (ret_val) + goto out; + + DEBUGOUT1("IFE PMC: %X\n", data); + + usec_delay(1); + + if (phy->autoneg_wait_to_complete) { + DEBUGOUT("Waiting for forced speed/duplex link on IFE phy.\n"); + + ret_val = e1000_phy_has_link_generic(hw, + PHY_FORCE_LIMIT, + 100000, + &link); + if (ret_val) + goto out; + + if (!link) + DEBUGOUT("Link taking longer than expected.\n"); + + /* Try once more */ + ret_val = e1000_phy_has_link_generic(hw, + PHY_FORCE_LIMIT, + 100000, + &link); + if (ret_val) + goto out; + } + +out: + return ret_val; +} + +/** + * e1000_phy_hw_reset_ich8lan - Performs a PHY reset + * @hw: pointer to the HW structure + * + * Resets the PHY + * This is a function pointer entry point called by drivers + * or other shared routines. + **/ +static s32 e1000_phy_hw_reset_ich8lan(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + u32 i, data, cnf_size, cnf_base_addr, sw_cfg_mask; + s32 ret_val; + u16 loop = E1000_ICH8_LAN_INIT_TIMEOUT; + u16 word_addr, reg_data, reg_addr, phy_page = 0; + + DEBUGFUNC("e1000_phy_hw_reset_ich8lan"); + + ret_val = e1000_phy_hw_reset_generic(hw); + if (ret_val) + goto out; + + /* + * Initialize the PHY from the NVM on ICH platforms. This + * is needed due to an issue where the NVM configuration is + * not properly autoloaded after power transitions. + * Therefore, after each PHY reset, we will load the + * configuration data out of the NVM manually. + */ + if (hw->mac.type == e1000_ich8lan && phy->type == e1000_phy_igp_3) { + /* Check if SW needs configure the PHY */ + if ((hw->device_id == E1000_DEV_ID_ICH8_IGP_M_AMT) || + (hw->device_id == E1000_DEV_ID_ICH8_IGP_M)) + sw_cfg_mask = E1000_FEXTNVM_SW_CONFIG_ICH8M; + else + sw_cfg_mask = E1000_FEXTNVM_SW_CONFIG; + + data = E1000_READ_REG(hw, E1000_FEXTNVM); + if (!(data & sw_cfg_mask)) + goto out; + + /* Wait for basic configuration completes before proceeding*/ + do { + data = E1000_READ_REG(hw, E1000_STATUS); + data &= E1000_STATUS_LAN_INIT_DONE; + usec_delay(100); + } while ((!data) && --loop); + + /* + * If basic configuration is incomplete before the above loop + * count reaches 0, loading the configuration from NVM will + * leave the PHY in a bad state possibly resulting in no link. + */ + if (loop == 0) + DEBUGOUT("LAN_INIT_DONE not set, increase timeout\n"); + + /* Clear the Init Done bit for the next init event */ + data = E1000_READ_REG(hw, E1000_STATUS); + data &= ~E1000_STATUS_LAN_INIT_DONE; + E1000_WRITE_REG(hw, E1000_STATUS, data); + + /* + * Make sure HW does not configure LCD from PHY + * extended configuration before SW configuration + */ + data = E1000_READ_REG(hw, E1000_EXTCNF_CTRL); + if (data & E1000_EXTCNF_CTRL_LCD_WRITE_ENABLE) + goto out; + + cnf_size = E1000_READ_REG(hw, E1000_EXTCNF_SIZE); + cnf_size &= E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH_MASK; + cnf_size >>= E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH_SHIFT; + if (!cnf_size) + goto out; + + cnf_base_addr = data & E1000_EXTCNF_CTRL_EXT_CNF_POINTER_MASK; + cnf_base_addr >>= E1000_EXTCNF_CTRL_EXT_CNF_POINTER_SHIFT; + + /* Configure LCD from extended configuration region. */ + + /* cnf_base_addr is in DWORD */ + word_addr = (u16)(cnf_base_addr << 1); + + for (i = 0; i < cnf_size; i++) { + ret_val = hw->nvm.ops.read(hw, (word_addr + i * 2), 1, + ®_data); + if (ret_val) + goto out; + + ret_val = hw->nvm.ops.read(hw, (word_addr + i * 2 + 1), + 1, ®_addr); + if (ret_val) + goto out; + + /* Save off the PHY page for future writes. */ + if (reg_addr == IGP01E1000_PHY_PAGE_SELECT) { + phy_page = reg_data; + continue; + } + + reg_addr |= phy_page; + + ret_val = phy->ops.write_reg(hw, (u32)reg_addr, reg_data); + if (ret_val) + goto out; + } + } + +out: + return ret_val; +} + +/** + * e1000_get_phy_info_ich8lan - Calls appropriate PHY type get_phy_info + * @hw: pointer to the HW structure + * + * Wrapper for calling the get_phy_info routines for the appropriate phy type. + **/ +static s32 e1000_get_phy_info_ich8lan(struct e1000_hw *hw) +{ + s32 ret_val = -E1000_ERR_PHY_TYPE; + + DEBUGFUNC("e1000_get_phy_info_ich8lan"); + + switch (hw->phy.type) { + case e1000_phy_ife: + ret_val = e1000_get_phy_info_ife_ich8lan(hw); + break; + case e1000_phy_igp_3: + case e1000_phy_bm: + ret_val = e1000_get_phy_info_igp(hw); + break; + default: + break; + } + + return ret_val; +} + +/** + * e1000_get_phy_info_ife_ich8lan - Retrieves various IFE PHY states + * @hw: pointer to the HW structure + * + * Populates "phy" structure with various feature states. + * This function is only called by other family-specific + * routines. + **/ +static s32 e1000_get_phy_info_ife_ich8lan(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val; + u16 data; + bool link; + + DEBUGFUNC("e1000_get_phy_info_ife_ich8lan"); + + ret_val = e1000_phy_has_link_generic(hw, 1, 0, &link); + if (ret_val) + goto out; + + if (!link) { + DEBUGOUT("Phy info is only valid if link is up\n"); + ret_val = -E1000_ERR_CONFIG; + goto out; + } + + ret_val = phy->ops.read_reg(hw, IFE_PHY_SPECIAL_CONTROL, &data); + if (ret_val) + goto out; + phy->polarity_correction = (data & IFE_PSC_AUTO_POLARITY_DISABLE) + ? FALSE : TRUE; + + if (phy->polarity_correction) { + ret_val = e1000_check_polarity_ife_ich8lan(hw); + if (ret_val) + goto out; + } else { + /* Polarity is forced */ + phy->cable_polarity = (data & IFE_PSC_FORCE_POLARITY) + ? e1000_rev_polarity_reversed + : e1000_rev_polarity_normal; + } + + ret_val = phy->ops.read_reg(hw, IFE_PHY_MDIX_CONTROL, &data); + if (ret_val) + goto out; + + phy->is_mdix = (data & IFE_PMC_MDIX_STATUS) ? TRUE : FALSE; + + /* The following parameters are undefined for 10/100 operation. */ + phy->cable_length = E1000_CABLE_LENGTH_UNDEFINED; + phy->local_rx = e1000_1000t_rx_status_undefined; + phy->remote_rx = e1000_1000t_rx_status_undefined; + +out: + return ret_val; +} + +/** + * e1000_check_polarity_ife_ich8lan - Check cable polarity for IFE PHY + * @hw: pointer to the HW structure + * + * Polarity is determined on the polarity reversal feature being enabled. + * This function is only called by other family-specific + * routines. + **/ +static s32 e1000_check_polarity_ife_ich8lan(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val; + u16 phy_data, offset, mask; + + DEBUGFUNC("e1000_check_polarity_ife_ich8lan"); + + /* + * Polarity is determined based on the reversal feature being enabled. + */ + if (phy->polarity_correction) { + offset = IFE_PHY_EXTENDED_STATUS_CONTROL; + mask = IFE_PESC_POLARITY_REVERSED; + } else { + offset = IFE_PHY_SPECIAL_CONTROL; + mask = IFE_PSC_FORCE_POLARITY; + } + + ret_val = phy->ops.read_reg(hw, offset, &phy_data); + + if (!ret_val) + phy->cable_polarity = (phy_data & mask) + ? e1000_rev_polarity_reversed + : e1000_rev_polarity_normal; + + return ret_val; +} + +/** + * e1000_set_d0_lplu_state_ich8lan - Set Low Power Linkup D0 state + * @hw: pointer to the HW structure + * @active: TRUE to enable LPLU, FALSE to disable + * + * Sets the LPLU D0 state according to the active flag. When + * activating LPLU this function also disables smart speed + * and vice versa. LPLU will not be activated unless the + * device autonegotiation advertisement meets standards of + * either 10 or 10/100 or 10/100/1000 at all duplexes. + * This is a function pointer entry point only called by + * PHY setup routines. + **/ +static s32 e1000_set_d0_lplu_state_ich8lan(struct e1000_hw *hw, bool active) +{ + struct e1000_phy_info *phy = &hw->phy; + u32 phy_ctrl; + s32 ret_val = E1000_SUCCESS; + u16 data; + + DEBUGFUNC("e1000_set_d0_lplu_state_ich8lan"); + + if (phy->type == e1000_phy_ife) + goto out; + + phy_ctrl = E1000_READ_REG(hw, E1000_PHY_CTRL); + + if (active) { + phy_ctrl |= E1000_PHY_CTRL_D0A_LPLU; + E1000_WRITE_REG(hw, E1000_PHY_CTRL, phy_ctrl); + + /* + * Call gig speed drop workaround on LPLU before accessing + * any PHY registers + */ + if ((hw->mac.type == e1000_ich8lan) && + (hw->phy.type == e1000_phy_igp_3)) + e1000_gig_downshift_workaround_ich8lan(hw); + + /* When LPLU is enabled, we should disable SmartSpeed */ + ret_val = phy->ops.read_reg(hw, + IGP01E1000_PHY_PORT_CONFIG, + &data); + data &= ~IGP01E1000_PSCFR_SMART_SPEED; + ret_val = phy->ops.write_reg(hw, + IGP01E1000_PHY_PORT_CONFIG, + data); + if (ret_val) + goto out; + } else { + phy_ctrl &= ~E1000_PHY_CTRL_D0A_LPLU; + E1000_WRITE_REG(hw, E1000_PHY_CTRL, phy_ctrl); + + /* + * LPLU and SmartSpeed are mutually exclusive. LPLU is used + * during Dx states where the power conservation is most + * important. During driver activity we should enable + * SmartSpeed, so performance is maintained. + */ + if (phy->smart_speed == e1000_smart_speed_on) { + ret_val = phy->ops.read_reg(hw, + IGP01E1000_PHY_PORT_CONFIG, + &data); + if (ret_val) + goto out; + + data |= IGP01E1000_PSCFR_SMART_SPEED; + ret_val = phy->ops.write_reg(hw, + IGP01E1000_PHY_PORT_CONFIG, + data); + if (ret_val) + goto out; + } else if (phy->smart_speed == e1000_smart_speed_off) { + ret_val = phy->ops.read_reg(hw, + IGP01E1000_PHY_PORT_CONFIG, + &data); + if (ret_val) + goto out; + + data &= ~IGP01E1000_PSCFR_SMART_SPEED; + ret_val = phy->ops.write_reg(hw, + IGP01E1000_PHY_PORT_CONFIG, + data); + if (ret_val) + goto out; + } + } + +out: + return ret_val; +} + +/** + * e1000_set_d3_lplu_state_ich8lan - Set Low Power Linkup D3 state + * @hw: pointer to the HW structure + * @active: TRUE to enable LPLU, FALSE to disable + * + * Sets the LPLU D3 state according to the active flag. When + * activating LPLU this function also disables smart speed + * and vice versa. LPLU will not be activated unless the + * device autonegotiation advertisement meets standards of + * either 10 or 10/100 or 10/100/1000 at all duplexes. + * This is a function pointer entry point only called by + * PHY setup routines. + **/ +static s32 e1000_set_d3_lplu_state_ich8lan(struct e1000_hw *hw, bool active) +{ + struct e1000_phy_info *phy = &hw->phy; + u32 phy_ctrl; + s32 ret_val = E1000_SUCCESS; + u16 data; + + DEBUGFUNC("e1000_set_d3_lplu_state_ich8lan"); + + phy_ctrl = E1000_READ_REG(hw, E1000_PHY_CTRL); + + if (!active) { + phy_ctrl &= ~E1000_PHY_CTRL_NOND0A_LPLU; + E1000_WRITE_REG(hw, E1000_PHY_CTRL, phy_ctrl); + /* + * LPLU and SmartSpeed are mutually exclusive. LPLU is used + * during Dx states where the power conservation is most + * important. During driver activity we should enable + * SmartSpeed, so performance is maintained. + */ + if (phy->smart_speed == e1000_smart_speed_on) { + ret_val = phy->ops.read_reg(hw, + IGP01E1000_PHY_PORT_CONFIG, + &data); + if (ret_val) + goto out; + + data |= IGP01E1000_PSCFR_SMART_SPEED; + ret_val = phy->ops.write_reg(hw, + IGP01E1000_PHY_PORT_CONFIG, + data); + if (ret_val) + goto out; + } else if (phy->smart_speed == e1000_smart_speed_off) { + ret_val = phy->ops.read_reg(hw, + IGP01E1000_PHY_PORT_CONFIG, + &data); + if (ret_val) + goto out; + + data &= ~IGP01E1000_PSCFR_SMART_SPEED; + ret_val = phy->ops.write_reg(hw, + IGP01E1000_PHY_PORT_CONFIG, + data); + if (ret_val) + goto out; + } + } else if ((phy->autoneg_advertised == E1000_ALL_SPEED_DUPLEX) || + (phy->autoneg_advertised == E1000_ALL_NOT_GIG) || + (phy->autoneg_advertised == E1000_ALL_10_SPEED)) { + phy_ctrl |= E1000_PHY_CTRL_NOND0A_LPLU; + E1000_WRITE_REG(hw, E1000_PHY_CTRL, phy_ctrl); + + /* + * Call gig speed drop workaround on LPLU before accessing + * any PHY registers + */ + if ((hw->mac.type == e1000_ich8lan) && + (hw->phy.type == e1000_phy_igp_3)) + e1000_gig_downshift_workaround_ich8lan(hw); + + /* When LPLU is enabled, we should disable SmartSpeed */ + ret_val = phy->ops.read_reg(hw, + IGP01E1000_PHY_PORT_CONFIG, + &data); + if (ret_val) + goto out; + + data &= ~IGP01E1000_PSCFR_SMART_SPEED; + ret_val = phy->ops.write_reg(hw, + IGP01E1000_PHY_PORT_CONFIG, + data); + } + +out: + return ret_val; +} + +/** + * e1000_valid_nvm_bank_detect_ich8lan - finds out the valid bank 0 or 1 + * @hw: pointer to the HW structure + * @bank: pointer to the variable that returns the active bank + * + * Reads signature byte from the NVM using the flash access registers. + **/ +static s32 e1000_valid_nvm_bank_detect_ich8lan(struct e1000_hw *hw, u32 *bank) +{ + s32 ret_val = E1000_SUCCESS; + struct e1000_nvm_info *nvm = &hw->nvm; + /* flash bank size is in words */ + u32 bank1_offset = nvm->flash_bank_size * sizeof(u16); + u32 act_offset = E1000_ICH_NVM_SIG_WORD * 2 + 1; + u8 bank_high_byte = 0; + + if (hw->mac.type != e1000_ich10lan) { + if (E1000_READ_REG(hw, E1000_EECD) & E1000_EECD_SEC1VAL) + *bank = 1; + else + *bank = 0; + } else { + /* + * Make sure the signature for bank 0 is valid, + * if not check for bank1 + */ + e1000_read_flash_byte_ich8lan(hw, act_offset, &bank_high_byte); + if ((bank_high_byte & 0xC0) == 0x80) { + *bank = 0; + } else { + /* + * find if segment 1 is valid by verifying + * bit 15:14 = 10b in word 0x13 + */ + e1000_read_flash_byte_ich8lan(hw, + act_offset + bank1_offset, + &bank_high_byte); + + /* bank1 has a valid signature equivalent to SEC1V */ + if ((bank_high_byte & 0xC0) == 0x80) { + *bank = 1; + } else { + DEBUGOUT("ERROR: EEPROM not present\n"); + ret_val = -E1000_ERR_NVM; + } + } + } + + return ret_val; +} + +/** + * e1000_read_nvm_ich8lan - Read word(s) from the NVM + * @hw: pointer to the HW structure + * @offset: The offset (in bytes) of the word(s) to read. + * @words: Size of data to read in words + * @data: Pointer to the word(s) to read at offset. + * + * Reads a word(s) from the NVM using the flash access registers. + **/ +static s32 e1000_read_nvm_ich8lan(struct e1000_hw *hw, u16 offset, u16 words, + u16 *data) +{ + struct e1000_nvm_info *nvm = &hw->nvm; + struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan; + u32 act_offset; + s32 ret_val = E1000_SUCCESS; + u32 bank = 0; + u16 i, word; + + DEBUGFUNC("e1000_read_nvm_ich8lan"); + + if ((offset >= nvm->word_size) || (words > nvm->word_size - offset) || + (words == 0)) { + DEBUGOUT("nvm parameter(s) out of bounds\n"); + ret_val = -E1000_ERR_NVM; + goto out; + } + + ret_val = nvm->ops.acquire(hw); + if (ret_val) + goto out; + + ret_val = e1000_valid_nvm_bank_detect_ich8lan(hw, &bank); + if (ret_val != E1000_SUCCESS) + goto out; + + act_offset = (bank) ? nvm->flash_bank_size : 0; + act_offset += offset; + + for (i = 0; i < words; i++) { + if ((dev_spec->shadow_ram) && + (dev_spec->shadow_ram[offset+i].modified)) { + data[i] = dev_spec->shadow_ram[offset+i].value; + } else { + ret_val = e1000_read_flash_word_ich8lan(hw, + act_offset + i, + &word); + if (ret_val) + break; + data[i] = word; + } + } + + nvm->ops.release(hw); + +out: + return ret_val; +} + +/** + * e1000_flash_cycle_init_ich8lan - Initialize flash + * @hw: pointer to the HW structure + * + * This function does initial flash setup so that a new read/write/erase cycle + * can be started. + **/ +static s32 e1000_flash_cycle_init_ich8lan(struct e1000_hw *hw) +{ + union ich8_hws_flash_status hsfsts; + s32 ret_val = -E1000_ERR_NVM; + s32 i = 0; + + DEBUGFUNC("e1000_flash_cycle_init_ich8lan"); + + hsfsts.regval = E1000_READ_FLASH_REG16(hw, ICH_FLASH_HSFSTS); + + /* Check if the flash descriptor is valid */ + if (hsfsts.hsf_status.fldesvalid == 0) { + DEBUGOUT("Flash descriptor invalid. " + "SW Sequencing must be used."); + goto out; + } + + /* Clear FCERR and DAEL in hw status by writing 1 */ + hsfsts.hsf_status.flcerr = 1; + hsfsts.hsf_status.dael = 1; + + E1000_WRITE_FLASH_REG16(hw, ICH_FLASH_HSFSTS, hsfsts.regval); + + /* + * Either we should have a hardware SPI cycle in progress + * bit to check against, in order to start a new cycle or + * FDONE bit should be changed in the hardware so that it + * is 1 after hardware reset, which can then be used as an + * indication whether a cycle is in progress or has been + * completed. + */ + + if (hsfsts.hsf_status.flcinprog == 0) { + /* + * There is no cycle running at present, + * so we can start a cycle. + * Begin by setting Flash Cycle Done. + */ + hsfsts.hsf_status.flcdone = 1; + E1000_WRITE_FLASH_REG16(hw, ICH_FLASH_HSFSTS, hsfsts.regval); + ret_val = E1000_SUCCESS; + } else { + /* + * Otherwise poll for sometime so the current + * cycle has a chance to end before giving up. + */ + for (i = 0; i < ICH_FLASH_READ_COMMAND_TIMEOUT; i++) { + hsfsts.regval = E1000_READ_FLASH_REG16(hw, + ICH_FLASH_HSFSTS); + if (hsfsts.hsf_status.flcinprog == 0) { + ret_val = E1000_SUCCESS; + break; + } + usec_delay(1); + } + if (ret_val == E1000_SUCCESS) { + /* + * Successful in waiting for previous cycle to timeout, + * now set the Flash Cycle Done. + */ + hsfsts.hsf_status.flcdone = 1; + E1000_WRITE_FLASH_REG16(hw, ICH_FLASH_HSFSTS, + hsfsts.regval); + } else { + DEBUGOUT("Flash controller busy, cannot get access"); + } + } + +out: + return ret_val; +} + +/** + * e1000_flash_cycle_ich8lan - Starts flash cycle (read/write/erase) + * @hw: pointer to the HW structure + * @timeout: maximum time to wait for completion + * + * This function starts a flash cycle and waits for its completion. + **/ +static s32 e1000_flash_cycle_ich8lan(struct e1000_hw *hw, u32 timeout) +{ + union ich8_hws_flash_ctrl hsflctl; + union ich8_hws_flash_status hsfsts; + s32 ret_val = -E1000_ERR_NVM; + u32 i = 0; + + DEBUGFUNC("e1000_flash_cycle_ich8lan"); + + /* Start a cycle by writing 1 in Flash Cycle Go in Hw Flash Control */ + hsflctl.regval = E1000_READ_FLASH_REG16(hw, ICH_FLASH_HSFCTL); + hsflctl.hsf_ctrl.flcgo = 1; + E1000_WRITE_FLASH_REG16(hw, ICH_FLASH_HSFCTL, hsflctl.regval); + + /* wait till FDONE bit is set to 1 */ + do { + hsfsts.regval = E1000_READ_FLASH_REG16(hw, ICH_FLASH_HSFSTS); + if (hsfsts.hsf_status.flcdone == 1) + break; + usec_delay(1); + } while (i++ < timeout); + + if (hsfsts.hsf_status.flcdone == 1 && hsfsts.hsf_status.flcerr == 0) + ret_val = E1000_SUCCESS; + + return ret_val; +} + +/** + * e1000_read_flash_word_ich8lan - Read word from flash + * @hw: pointer to the HW structure + * @offset: offset to data location + * @data: pointer to the location for storing the data + * + * Reads the flash word at offset into data. Offset is converted + * to bytes before read. + **/ +static s32 e1000_read_flash_word_ich8lan(struct e1000_hw *hw, u32 offset, + u16 *data) +{ + s32 ret_val; + + DEBUGFUNC("e1000_read_flash_word_ich8lan"); + + if (!data) { + ret_val = -E1000_ERR_NVM; + goto out; + } + + /* Must convert offset into bytes. */ + offset <<= 1; + + ret_val = e1000_read_flash_data_ich8lan(hw, offset, 2, data); + +out: + return ret_val; +} + +/** + * e1000_read_flash_byte_ich8lan - Read byte from flash + * @hw: pointer to the HW structure + * @offset: The offset of the byte to read. + * @data: Pointer to a byte to store the value read. + * + * Reads a single byte from the NVM using the flash access registers. + **/ +static s32 e1000_read_flash_byte_ich8lan(struct e1000_hw *hw, u32 offset, + u8 *data) +{ + s32 ret_val = E1000_SUCCESS; + u16 word = 0; + + ret_val = e1000_read_flash_data_ich8lan(hw, offset, 1, &word); + if (ret_val) + goto out; + + *data = (u8)word; + +out: + return ret_val; +} + +/** + * e1000_read_flash_data_ich8lan - Read byte or word from NVM + * @hw: pointer to the HW structure + * @offset: The offset (in bytes) of the byte or word to read. + * @size: Size of data to read, 1=byte 2=word + * @data: Pointer to the word to store the value read. + * + * Reads a byte or word from the NVM using the flash access registers. + **/ +static s32 e1000_read_flash_data_ich8lan(struct e1000_hw *hw, u32 offset, + u8 size, u16 *data) +{ + union ich8_hws_flash_status hsfsts; + union ich8_hws_flash_ctrl hsflctl; + u32 flash_linear_addr; + u32 flash_data = 0; + s32 ret_val = -E1000_ERR_NVM; + u8 count = 0; + + DEBUGFUNC("e1000_read_flash_data_ich8lan"); + + if (size < 1 || size > 2 || offset > ICH_FLASH_LINEAR_ADDR_MASK) + goto out; + + flash_linear_addr = (ICH_FLASH_LINEAR_ADDR_MASK & offset) + + hw->nvm.flash_base_addr; + + do { + usec_delay(1); + /* Steps */ + ret_val = e1000_flash_cycle_init_ich8lan(hw); + if (ret_val != E1000_SUCCESS) + break; + + hsflctl.regval = E1000_READ_FLASH_REG16(hw, ICH_FLASH_HSFCTL); + /* 0b/1b corresponds to 1 or 2 byte size, respectively. */ + hsflctl.hsf_ctrl.fldbcount = size - 1; + hsflctl.hsf_ctrl.flcycle = ICH_CYCLE_READ; + E1000_WRITE_FLASH_REG16(hw, ICH_FLASH_HSFCTL, hsflctl.regval); + + E1000_WRITE_FLASH_REG(hw, ICH_FLASH_FADDR, flash_linear_addr); + + ret_val = e1000_flash_cycle_ich8lan(hw, + ICH_FLASH_READ_COMMAND_TIMEOUT); + + /* + * Check if FCERR is set to 1, if set to 1, clear it + * and try the whole sequence a few more times, else + * read in (shift in) the Flash Data0, the order is + * least significant byte first msb to lsb + */ + if (ret_val == E1000_SUCCESS) { + flash_data = E1000_READ_FLASH_REG(hw, ICH_FLASH_FDATA0); + if (size == 1) + *data = (u8)(flash_data & 0x000000FF); + else if (size == 2) + *data = (u16)(flash_data & 0x0000FFFF); + break; + } else { + /* + * If we've gotten here, then things are probably + * completely hosed, but if the error condition is + * detected, it won't hurt to give it another try... + * ICH_FLASH_CYCLE_REPEAT_COUNT times. + */ + hsfsts.regval = E1000_READ_FLASH_REG16(hw, + ICH_FLASH_HSFSTS); + if (hsfsts.hsf_status.flcerr == 1) { + /* Repeat for some time before giving up. */ + continue; + } else if (hsfsts.hsf_status.flcdone == 0) { + DEBUGOUT("Timeout error - flash cycle " + "did not complete."); + break; + } + } + } while (count++ < ICH_FLASH_CYCLE_REPEAT_COUNT); + +out: + return ret_val; +} + +/** + * e1000_write_nvm_ich8lan - Write word(s) to the NVM + * @hw: pointer to the HW structure + * @offset: The offset (in bytes) of the word(s) to write. + * @words: Size of data to write in words + * @data: Pointer to the word(s) to write at offset. + * + * Writes a byte or word to the NVM using the flash access registers. + **/ +static s32 e1000_write_nvm_ich8lan(struct e1000_hw *hw, u16 offset, u16 words, + u16 *data) +{ + struct e1000_nvm_info *nvm = &hw->nvm; + struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan; + s32 ret_val = E1000_SUCCESS; + u16 i; + + DEBUGFUNC("e1000_write_nvm_ich8lan"); + + if ((offset >= nvm->word_size) || (words > nvm->word_size - offset) || + (words == 0)) { + DEBUGOUT("nvm parameter(s) out of bounds\n"); + ret_val = -E1000_ERR_NVM; + goto out; + } + + ret_val = nvm->ops.acquire(hw); + if (ret_val) + goto out; + + for (i = 0; i < words; i++) { + dev_spec->shadow_ram[offset+i].modified = TRUE; + dev_spec->shadow_ram[offset+i].value = data[i]; + } + + nvm->ops.release(hw); + +out: + return ret_val; +} + +/** + * e1000_update_nvm_checksum_ich8lan - Update the checksum for NVM + * @hw: pointer to the HW structure + * + * The NVM checksum is updated by calling the generic update_nvm_checksum, + * which writes the checksum to the shadow ram. The changes in the shadow + * ram are then committed to the EEPROM by processing each bank at a time + * checking for the modified bit and writing only the pending changes. + * After a successful commit, the shadow ram is cleared and is ready for + * future writes. + **/ +static s32 e1000_update_nvm_checksum_ich8lan(struct e1000_hw *hw) +{ + struct e1000_nvm_info *nvm = &hw->nvm; + struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan; + u32 i, act_offset, new_bank_offset, old_bank_offset, bank; + s32 ret_val; + u16 data; + + DEBUGFUNC("e1000_update_nvm_checksum_ich8lan"); + + ret_val = e1000_update_nvm_checksum_generic(hw); + if (ret_val) + goto out; + + if (nvm->type != e1000_nvm_flash_sw) + goto out; + + ret_val = nvm->ops.acquire(hw); + if (ret_val) + goto out; + + /* + * We're writing to the opposite bank so if we're on bank 1, + * write to bank 0 etc. We also need to erase the segment that + * is going to be written + */ + ret_val = e1000_valid_nvm_bank_detect_ich8lan(hw, &bank); + if (ret_val != E1000_SUCCESS) + goto out; + + if (bank == 0) { + new_bank_offset = nvm->flash_bank_size; + old_bank_offset = 0; + e1000_erase_flash_bank_ich8lan(hw, 1); + } else { + old_bank_offset = nvm->flash_bank_size; + new_bank_offset = 0; + e1000_erase_flash_bank_ich8lan(hw, 0); + } + + for (i = 0; i < E1000_SHADOW_RAM_WORDS; i++) { + /* + * Determine whether to write the value stored + * in the other NVM bank or a modified value stored + * in the shadow RAM + */ + if (dev_spec->shadow_ram[i].modified) { + data = dev_spec->shadow_ram[i].value; + } else { + e1000_read_flash_word_ich8lan(hw, + i + old_bank_offset, + &data); + } + + /* + * If the word is 0x13, then make sure the signature bits + * (15:14) are 11b until the commit has completed. + * This will allow us to write 10b which indicates the + * signature is valid. We want to do this after the write + * has completed so that we don't mark the segment valid + * while the write is still in progress + */ + if (i == E1000_ICH_NVM_SIG_WORD) + data |= E1000_ICH_NVM_SIG_MASK; + + /* Convert offset to bytes. */ + act_offset = (i + new_bank_offset) << 1; + + usec_delay(100); + /* Write the bytes to the new bank. */ + ret_val = e1000_retry_write_flash_byte_ich8lan(hw, + act_offset, + (u8)data); + if (ret_val) + break; + + usec_delay(100); + ret_val = e1000_retry_write_flash_byte_ich8lan(hw, + act_offset + 1, + (u8)(data >> 8)); + if (ret_val) + break; + } + + /* + * Don't bother writing the segment valid bits if sector + * programming failed. + */ + if (ret_val) { + DEBUGOUT("Flash commit failed.\n"); + nvm->ops.release(hw); + goto out; + } + + /* + * Finally validate the new segment by setting bit 15:14 + * to 10b in word 0x13 , this can be done without an + * erase as well since these bits are 11 to start with + * and we need to change bit 14 to 0b + */ + act_offset = new_bank_offset + E1000_ICH_NVM_SIG_WORD; + e1000_read_flash_word_ich8lan(hw, act_offset, &data); + data &= 0xBFFF; + ret_val = e1000_retry_write_flash_byte_ich8lan(hw, + act_offset * 2 + 1, + (u8)(data >> 8)); + if (ret_val) { + nvm->ops.release(hw); + goto out; + } + + /* + * And invalidate the previously valid segment by setting + * its signature word (0x13) high_byte to 0b. This can be + * done without an erase because flash erase sets all bits + * to 1's. We can write 1's to 0's without an erase + */ + act_offset = (old_bank_offset + E1000_ICH_NVM_SIG_WORD) * 2 + 1; + ret_val = e1000_retry_write_flash_byte_ich8lan(hw, act_offset, 0); + if (ret_val) { + nvm->ops.release(hw); + goto out; + } + + /* Great! Everything worked, we can now clear the cached entries. */ + for (i = 0; i < E1000_SHADOW_RAM_WORDS; i++) { + dev_spec->shadow_ram[i].modified = FALSE; + dev_spec->shadow_ram[i].value = 0xFFFF; + } + + nvm->ops.release(hw); + + /* + * Reload the EEPROM, or else modifications will not appear + * until after the next adapter reset. + */ + nvm->ops.reload(hw); + msec_delay(10); + +out: + return ret_val; +} + +/** + * e1000_validate_nvm_checksum_ich8lan - Validate EEPROM checksum + * @hw: pointer to the HW structure + * + * Check to see if checksum needs to be fixed by reading bit 6 in word 0x19. + * If the bit is 0, that the EEPROM had been modified, but the checksum was not + * calculated, in which case we need to calculate the checksum and set bit 6. + **/ +static s32 e1000_validate_nvm_checksum_ich8lan(struct e1000_hw *hw) +{ + s32 ret_val = E1000_SUCCESS; + u16 data; + + DEBUGFUNC("e1000_validate_nvm_checksum_ich8lan"); + + /* + * Read 0x19 and check bit 6. If this bit is 0, the checksum + * needs to be fixed. This bit is an indication that the NVM + * was prepared by OEM software and did not calculate the + * checksum...a likely scenario. + */ + ret_val = hw->nvm.ops.read(hw, 0x19, 1, &data); + if (ret_val) + goto out; + + if ((data & 0x40) == 0) { + data |= 0x40; + ret_val = hw->nvm.ops.write(hw, 0x19, 1, &data); + if (ret_val) + goto out; + ret_val = hw->nvm.ops.update(hw); + if (ret_val) + goto out; + } + + ret_val = e1000_validate_nvm_checksum_generic(hw); + +out: + return ret_val; +} + +/** + * e1000_write_flash_data_ich8lan - Writes bytes to the NVM + * @hw: pointer to the HW structure + * @offset: The offset (in bytes) of the byte/word to read. + * @size: Size of data to read, 1=byte 2=word + * @data: The byte(s) to write to the NVM. + * + * Writes one/two bytes to the NVM using the flash access registers. + **/ +static s32 e1000_write_flash_data_ich8lan(struct e1000_hw *hw, u32 offset, + u8 size, u16 data) +{ + union ich8_hws_flash_status hsfsts; + union ich8_hws_flash_ctrl hsflctl; + u32 flash_linear_addr; + u32 flash_data = 0; + s32 ret_val = -E1000_ERR_NVM; + u8 count = 0; + + DEBUGFUNC("e1000_write_ich8_data"); + + if (size < 1 || size > 2 || data > size * 0xff || + offset > ICH_FLASH_LINEAR_ADDR_MASK) + goto out; + + flash_linear_addr = (ICH_FLASH_LINEAR_ADDR_MASK & offset) + + hw->nvm.flash_base_addr; + + do { + usec_delay(1); + /* Steps */ + ret_val = e1000_flash_cycle_init_ich8lan(hw); + if (ret_val != E1000_SUCCESS) + break; + + hsflctl.regval = E1000_READ_FLASH_REG16(hw, ICH_FLASH_HSFCTL); + /* 0b/1b corresponds to 1 or 2 byte size, respectively. */ + hsflctl.hsf_ctrl.fldbcount = size - 1; + hsflctl.hsf_ctrl.flcycle = ICH_CYCLE_WRITE; + E1000_WRITE_FLASH_REG16(hw, ICH_FLASH_HSFCTL, hsflctl.regval); + + E1000_WRITE_FLASH_REG(hw, ICH_FLASH_FADDR, flash_linear_addr); + + if (size == 1) + flash_data = (u32)data & 0x00FF; + else + flash_data = (u32)data; + + E1000_WRITE_FLASH_REG(hw, ICH_FLASH_FDATA0, flash_data); + + /* + * check if FCERR is set to 1 , if set to 1, clear it + * and try the whole sequence a few more times else done + */ + ret_val = e1000_flash_cycle_ich8lan(hw, + ICH_FLASH_WRITE_COMMAND_TIMEOUT); + if (ret_val == E1000_SUCCESS) + break; + + /* + * If we're here, then things are most likely + * completely hosed, but if the error condition + * is detected, it won't hurt to give it another + * try...ICH_FLASH_CYCLE_REPEAT_COUNT times. + */ + hsfsts.regval = E1000_READ_FLASH_REG16(hw, ICH_FLASH_HSFSTS); + if (hsfsts.hsf_status.flcerr == 1) { + /* Repeat for some time before giving up. */ + continue; + } else if (hsfsts.hsf_status.flcdone == 0) { + DEBUGOUT("Timeout error - flash cycle " + "did not complete."); + break; + } + } while (count++ < ICH_FLASH_CYCLE_REPEAT_COUNT); + +out: + return ret_val; +} + +/** + * e1000_write_flash_byte_ich8lan - Write a single byte to NVM + * @hw: pointer to the HW structure + * @offset: The index of the byte to read. + * @data: The byte to write to the NVM. + * + * Writes a single byte to the NVM using the flash access registers. + **/ +static s32 e1000_write_flash_byte_ich8lan(struct e1000_hw *hw, u32 offset, + u8 data) +{ + u16 word = (u16)data; + + DEBUGFUNC("e1000_write_flash_byte_ich8lan"); + + return e1000_write_flash_data_ich8lan(hw, offset, 1, word); +} + +/** + * e1000_retry_write_flash_byte_ich8lan - Writes a single byte to NVM + * @hw: pointer to the HW structure + * @offset: The offset of the byte to write. + * @byte: The byte to write to the NVM. + * + * Writes a single byte to the NVM using the flash access registers. + * Goes through a retry algorithm before giving up. + **/ +static s32 e1000_retry_write_flash_byte_ich8lan(struct e1000_hw *hw, + u32 offset, u8 byte) +{ + s32 ret_val; + u16 program_retries; + + DEBUGFUNC("e1000_retry_write_flash_byte_ich8lan"); + + ret_val = e1000_write_flash_byte_ich8lan(hw, offset, byte); + if (ret_val == E1000_SUCCESS) + goto out; + + for (program_retries = 0; program_retries < 100; program_retries++) { + DEBUGOUT2("Retrying Byte %2.2X at offset %u\n", byte, offset); + usec_delay(100); + ret_val = e1000_write_flash_byte_ich8lan(hw, offset, byte); + if (ret_val == E1000_SUCCESS) + break; + } + if (program_retries == 100) { + ret_val = -E1000_ERR_NVM; + goto out; + } + +out: + return ret_val; +} + +/** + * e1000_erase_flash_bank_ich8lan - Erase a bank (4k) from NVM + * @hw: pointer to the HW structure + * @bank: 0 for first bank, 1 for second bank, etc. + * + * Erases the bank specified. Each bank is a 4k block. Banks are 0 based. + * bank N is 4096 * N + flash_reg_addr. + **/ +static s32 e1000_erase_flash_bank_ich8lan(struct e1000_hw *hw, u32 bank) +{ + struct e1000_nvm_info *nvm = &hw->nvm; + union ich8_hws_flash_status hsfsts; + union ich8_hws_flash_ctrl hsflctl; + u32 flash_linear_addr; + /* bank size is in 16bit words - adjust to bytes */ + u32 flash_bank_size = nvm->flash_bank_size * 2; + s32 ret_val = E1000_SUCCESS; + s32 count = 0; + s32 j, iteration, sector_size; + + DEBUGFUNC("e1000_erase_flash_bank_ich8lan"); + + hsfsts.regval = E1000_READ_FLASH_REG16(hw, ICH_FLASH_HSFSTS); + + /* + * Determine HW Sector size: Read BERASE bits of hw flash status + * register + * 00: The Hw sector is 256 bytes, hence we need to erase 16 + * consecutive sectors. The start index for the nth Hw sector + * can be calculated as = bank * 4096 + n * 256 + * 01: The Hw sector is 4K bytes, hence we need to erase 1 sector. + * The start index for the nth Hw sector can be calculated + * as = bank * 4096 + * 10: The Hw sector is 8K bytes, nth sector = bank * 8192 + * (ich9 only, otherwise error condition) + * 11: The Hw sector is 64K bytes, nth sector = bank * 65536 + */ + switch (hsfsts.hsf_status.berasesz) { + case 0: + /* Hw sector size 256 */ + sector_size = ICH_FLASH_SEG_SIZE_256; + iteration = flash_bank_size / ICH_FLASH_SEG_SIZE_256; + break; + case 1: + sector_size = ICH_FLASH_SEG_SIZE_4K; + iteration = flash_bank_size / ICH_FLASH_SEG_SIZE_4K; + break; + case 2: + if (hw->mac.type == e1000_ich9lan) { + sector_size = ICH_FLASH_SEG_SIZE_8K; + iteration = flash_bank_size / ICH_FLASH_SEG_SIZE_8K; + } else { + ret_val = -E1000_ERR_NVM; + goto out; + } + break; + case 3: + sector_size = ICH_FLASH_SEG_SIZE_64K; + iteration = flash_bank_size / ICH_FLASH_SEG_SIZE_64K; + break; + default: + ret_val = -E1000_ERR_NVM; + goto out; + } + + /* Start with the base address, then add the sector offset. */ + flash_linear_addr = hw->nvm.flash_base_addr; + flash_linear_addr += (bank) ? (sector_size * iteration) : 0; + + for (j = 0; j < iteration ; j++) { + do { + /* Steps */ + ret_val = e1000_flash_cycle_init_ich8lan(hw); + if (ret_val) + goto out; + + /* + * Write a value 11 (block Erase) in Flash + * Cycle field in hw flash control + */ + hsflctl.regval = E1000_READ_FLASH_REG16(hw, + ICH_FLASH_HSFCTL); + hsflctl.hsf_ctrl.flcycle = ICH_CYCLE_ERASE; + E1000_WRITE_FLASH_REG16(hw, ICH_FLASH_HSFCTL, + hsflctl.regval); + + /* + * Write the last 24 bits of an index within the + * block into Flash Linear address field in Flash + * Address. + */ + flash_linear_addr += (j * sector_size); + E1000_WRITE_FLASH_REG(hw, ICH_FLASH_FADDR, + flash_linear_addr); + + ret_val = e1000_flash_cycle_ich8lan(hw, + ICH_FLASH_ERASE_COMMAND_TIMEOUT); + if (ret_val == E1000_SUCCESS) + break; + + /* + * Check if FCERR is set to 1. If 1, + * clear it and try the whole sequence + * a few more times else Done + */ + hsfsts.regval = E1000_READ_FLASH_REG16(hw, + ICH_FLASH_HSFSTS); + if (hsfsts.hsf_status.flcerr == 1) + /* repeat for some time before giving up */ + continue; + else if (hsfsts.hsf_status.flcdone == 0) + goto out; + } while (++count < ICH_FLASH_CYCLE_REPEAT_COUNT); + } + +out: + return ret_val; +} + +/** + * e1000_valid_led_default_ich8lan - Set the default LED settings + * @hw: pointer to the HW structure + * @data: Pointer to the LED settings + * + * Reads the LED default settings from the NVM to data. If the NVM LED + * settings is all 0's or F's, set the LED default to a valid LED default + * setting. + **/ +static s32 e1000_valid_led_default_ich8lan(struct e1000_hw *hw, u16 *data) +{ + s32 ret_val; + + DEBUGFUNC("e1000_valid_led_default_ich8lan"); + + ret_val = hw->nvm.ops.read(hw, NVM_ID_LED_SETTINGS, 1, data); + if (ret_val) { + DEBUGOUT("NVM Read Error\n"); + goto out; + } + + if (*data == ID_LED_RESERVED_0000 || + *data == ID_LED_RESERVED_FFFF) + *data = ID_LED_DEFAULT_ICH8LAN; + +out: + return ret_val; +} + +/** + * e1000_get_bus_info_ich8lan - Get/Set the bus type and width + * @hw: pointer to the HW structure + * + * ICH8 use the PCI Express bus, but does not contain a PCI Express Capability + * register, so the the bus width is hard coded. + **/ +static s32 e1000_get_bus_info_ich8lan(struct e1000_hw *hw) +{ + struct e1000_bus_info *bus = &hw->bus; + s32 ret_val; + + DEBUGFUNC("e1000_get_bus_info_ich8lan"); + + ret_val = e1000_get_bus_info_pcie_generic(hw); + + /* + * ICH devices are "PCI Express"-ish. They have + * a configuration space, but do not contain + * PCI Express Capability registers, so bus width + * must be hardcoded. + */ + if (bus->width == e1000_bus_width_unknown) + bus->width = e1000_bus_width_pcie_x1; + + return ret_val; +} + +/** + * e1000_reset_hw_ich8lan - Reset the hardware + * @hw: pointer to the HW structure + * + * Does a full reset of the hardware which includes a reset of the PHY and + * MAC. + **/ +static s32 e1000_reset_hw_ich8lan(struct e1000_hw *hw) +{ + u32 ctrl, icr, kab; + s32 ret_val; + + DEBUGFUNC("e1000_reset_hw_ich8lan"); + + /* + * Prevent the PCI-E bus from sticking if there is no TLP connection + * on the last TLP read/write transaction when MAC is reset. + */ + ret_val = e1000_disable_pcie_master_generic(hw); + if (ret_val) + DEBUGOUT("PCI-E Master disable polling has failed.\n"); + + DEBUGOUT("Masking off all interrupts\n"); + E1000_WRITE_REG(hw, E1000_IMC, 0xffffffff); + + /* + * Disable the Transmit and Receive units. Then delay to allow + * any pending transactions to complete before we hit the MAC + * with the global reset. + */ + E1000_WRITE_REG(hw, E1000_RCTL, 0); + E1000_WRITE_REG(hw, E1000_TCTL, E1000_TCTL_PSP); + E1000_WRITE_FLUSH(hw); + + msec_delay(10); + + /* Workaround for ICH8 bit corruption issue in FIFO memory */ + if (hw->mac.type == e1000_ich8lan) { + /* Set Tx and Rx buffer allocation to 8k apiece. */ + E1000_WRITE_REG(hw, E1000_PBA, E1000_PBA_8K); + /* Set Packet Buffer Size to 16k. */ + E1000_WRITE_REG(hw, E1000_PBS, E1000_PBS_16K); + } + + ctrl = E1000_READ_REG(hw, E1000_CTRL); + + if (!hw->phy.ops.check_reset_block(hw) && !hw->phy.reset_disable) { + /* + * PHY HW reset requires MAC CORE reset at the same + * time to make sure the interface between MAC and the + * external PHY is reset. + */ + ctrl |= E1000_CTRL_PHY_RST; + } + ret_val = e1000_acquire_swflag_ich8lan(hw); + DEBUGOUT("Issuing a global reset to ich8lan\n"); + E1000_WRITE_REG(hw, E1000_CTRL, (ctrl | E1000_CTRL_RST)); + msec_delay(20); + + ret_val = e1000_get_auto_rd_done_generic(hw); + if (ret_val) { + /* + * When auto config read does not complete, do not + * return with an error. This can happen in situations + * where there is no eeprom and prevents getting link. + */ + DEBUGOUT("Auto Read Done did not complete\n"); + } + + E1000_WRITE_REG(hw, E1000_IMC, 0xffffffff); + icr = E1000_READ_REG(hw, E1000_ICR); + + kab = E1000_READ_REG(hw, E1000_KABGTXD); + kab |= E1000_KABGTXD_BGSQLBIAS; + E1000_WRITE_REG(hw, E1000_KABGTXD, kab); + + return ret_val; +} + +/** + * e1000_init_hw_ich8lan - Initialize the hardware + * @hw: pointer to the HW structure + * + * Prepares the hardware for transmit and receive by doing the following: + * - initialize hardware bits + * - initialize LED identification + * - setup receive address registers + * - setup flow control + * - setup transmit descriptors + * - clear statistics + **/ +static s32 e1000_init_hw_ich8lan(struct e1000_hw *hw) +{ + struct e1000_mac_info *mac = &hw->mac; + u32 ctrl_ext, txdctl, snoop; + s32 ret_val; + u16 i; + + DEBUGFUNC("e1000_init_hw_ich8lan"); + + e1000_initialize_hw_bits_ich8lan(hw); + + /* Initialize identification LED */ + ret_val = e1000_id_led_init_generic(hw); + if (ret_val) { + DEBUGOUT("Error initializing identification LED\n"); + /* This is not fatal and we should not stop init due to this */ + } + + /* Setup the receive address. */ + e1000_init_rx_addrs_generic(hw, mac->rar_entry_count); + + /* Zero out the Multicast HASH table */ + DEBUGOUT("Zeroing the MTA\n"); + for (i = 0; i < mac->mta_reg_count; i++) + E1000_WRITE_REG_ARRAY(hw, E1000_MTA, i, 0); + + /* Setup link and flow control */ + ret_val = mac->ops.setup_link(hw); + + /* Set the transmit descriptor write-back policy for both queues */ + txdctl = E1000_READ_REG(hw, E1000_TXDCTL(0)); + txdctl = (txdctl & ~E1000_TXDCTL_WTHRESH) | + E1000_TXDCTL_FULL_TX_DESC_WB; + txdctl = (txdctl & ~E1000_TXDCTL_PTHRESH) | + E1000_TXDCTL_MAX_TX_DESC_PREFETCH; + E1000_WRITE_REG(hw, E1000_TXDCTL(0), txdctl); + txdctl = E1000_READ_REG(hw, E1000_TXDCTL(1)); + txdctl = (txdctl & ~E1000_TXDCTL_WTHRESH) | + E1000_TXDCTL_FULL_TX_DESC_WB; + txdctl = (txdctl & ~E1000_TXDCTL_PTHRESH) | + E1000_TXDCTL_MAX_TX_DESC_PREFETCH; + E1000_WRITE_REG(hw, E1000_TXDCTL(1), txdctl); + + /* + * ICH8 has opposite polarity of no_snoop bits. + * By default, we should use snoop behavior. + */ + if (mac->type == e1000_ich8lan) + snoop = PCIE_ICH8_SNOOP_ALL; + else + snoop = (u32)~(PCIE_NO_SNOOP_ALL); + e1000_set_pcie_no_snoop_generic(hw, snoop); + + ctrl_ext = E1000_READ_REG(hw, E1000_CTRL_EXT); + ctrl_ext |= E1000_CTRL_EXT_RO_DIS; + E1000_WRITE_REG(hw, E1000_CTRL_EXT, ctrl_ext); + + /* + * Clear all of the statistics registers (clear on read). It is + * important that we do this after we have tried to establish link + * because the symbol error count will increment wildly if there + * is no link. + */ + e1000_clear_hw_cntrs_ich8lan(hw); + + return ret_val; +} +/** + * e1000_initialize_hw_bits_ich8lan - Initialize required hardware bits + * @hw: pointer to the HW structure + * + * Sets/Clears required hardware bits necessary for correctly setting up the + * hardware for transmit and receive. + **/ +static void e1000_initialize_hw_bits_ich8lan(struct e1000_hw *hw) +{ + u32 reg; + + DEBUGFUNC("e1000_initialize_hw_bits_ich8lan"); + + /* Extended Device Control */ + reg = E1000_READ_REG(hw, E1000_CTRL_EXT); + reg |= (1 << 22); + E1000_WRITE_REG(hw, E1000_CTRL_EXT, reg); + + /* Transmit Descriptor Control 0 */ + reg = E1000_READ_REG(hw, E1000_TXDCTL(0)); + reg |= (1 << 22); + E1000_WRITE_REG(hw, E1000_TXDCTL(0), reg); + + /* Transmit Descriptor Control 1 */ + reg = E1000_READ_REG(hw, E1000_TXDCTL(1)); + reg |= (1 << 22); + E1000_WRITE_REG(hw, E1000_TXDCTL(1), reg); + + /* Transmit Arbitration Control 0 */ + reg = E1000_READ_REG(hw, E1000_TARC(0)); + if (hw->mac.type == e1000_ich8lan) + reg |= (1 << 28) | (1 << 29); + reg |= (1 << 23) | (1 << 24) | (1 << 26) | (1 << 27); + E1000_WRITE_REG(hw, E1000_TARC(0), reg); + + /* Transmit Arbitration Control 1 */ + reg = E1000_READ_REG(hw, E1000_TARC(1)); + if (E1000_READ_REG(hw, E1000_TCTL) & E1000_TCTL_MULR) + reg &= ~(1 << 28); + else + reg |= (1 << 28); + reg |= (1 << 24) | (1 << 26) | (1 << 30); + E1000_WRITE_REG(hw, E1000_TARC(1), reg); + + /* Device Status */ + if (hw->mac.type == e1000_ich8lan) { + reg = E1000_READ_REG(hw, E1000_STATUS); + reg &= ~(1 << 31); + E1000_WRITE_REG(hw, E1000_STATUS, reg); + } + + return; +} + +/** + * e1000_setup_link_ich8lan - Setup flow control and link settings + * @hw: pointer to the HW structure + * + * Determines which flow control settings to use, then configures flow + * control. Calls the appropriate media-specific link configuration + * function. Assuming the adapter has a valid link partner, a valid link + * should be established. Assumes the hardware has previously been reset + * and the transmitter and receiver are not enabled. + **/ +static s32 e1000_setup_link_ich8lan(struct e1000_hw *hw) +{ + s32 ret_val = E1000_SUCCESS; + + DEBUGFUNC("e1000_setup_link_ich8lan"); + + if (hw->phy.ops.check_reset_block(hw)) + goto out; + + /* + * ICH parts do not have a word in the NVM to determine + * the default flow control setting, so we explicitly + * set it to full. + */ + if (hw->fc.requested_mode == e1000_fc_default) + hw->fc.requested_mode = e1000_fc_full; + + /* + * Save off the requested flow control mode for use later. Depending + * on the link partner's capabilities, we may or may not use this mode. + */ + hw->fc.current_mode = hw->fc.requested_mode; + + DEBUGOUT1("After fix-ups FlowControl is now = %x\n", + hw->fc.current_mode); + + /* Continue to configure the copper link. */ + ret_val = hw->mac.ops.setup_physical_interface(hw); + if (ret_val) + goto out; + + E1000_WRITE_REG(hw, E1000_FCTTV, hw->fc.pause_time); + + ret_val = e1000_set_fc_watermarks_generic(hw); + +out: + return ret_val; +} + +/** + * e1000_setup_copper_link_ich8lan - Configure MAC/PHY interface + * @hw: pointer to the HW structure + * + * Configures the kumeran interface to the PHY to wait the appropriate time + * when polling the PHY, then call the generic setup_copper_link to finish + * configuring the copper link. + **/ +static s32 e1000_setup_copper_link_ich8lan(struct e1000_hw *hw) +{ + u32 ctrl; + s32 ret_val; + u16 reg_data; + + DEBUGFUNC("e1000_setup_copper_link_ich8lan"); + + ctrl = E1000_READ_REG(hw, E1000_CTRL); + ctrl |= E1000_CTRL_SLU; + ctrl &= ~(E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX); + E1000_WRITE_REG(hw, E1000_CTRL, ctrl); + + /* + * Set the mac to wait the maximum time between each iteration + * and increase the max iterations when polling the phy; + * this fixes erroneous timeouts at 10Mbps. + */ + ret_val = e1000_write_kmrn_reg_generic(hw, GG82563_REG(0x34, 4), + 0xFFFF); + if (ret_val) + goto out; + ret_val = e1000_read_kmrn_reg_generic(hw, GG82563_REG(0x34, 9), + ®_data); + if (ret_val) + goto out; + reg_data |= 0x3F; + ret_val = e1000_write_kmrn_reg_generic(hw, GG82563_REG(0x34, 9), + reg_data); + if (ret_val) + goto out; + + if (hw->phy.type == e1000_phy_igp_3) { + ret_val = e1000_copper_link_setup_igp(hw); + if (ret_val) + goto out; + } else if (hw->phy.type == e1000_phy_bm) { + ret_val = e1000_copper_link_setup_m88(hw); + if (ret_val) + goto out; + } + + if (hw->phy.type == e1000_phy_ife) { + ret_val = hw->phy.ops.read_reg(hw, IFE_PHY_MDIX_CONTROL, + ®_data); + if (ret_val) + goto out; + + reg_data &= ~IFE_PMC_AUTO_MDIX; + + switch (hw->phy.mdix) { + case 1: + reg_data &= ~IFE_PMC_FORCE_MDIX; + break; + case 2: + reg_data |= IFE_PMC_FORCE_MDIX; + break; + case 0: + default: + reg_data |= IFE_PMC_AUTO_MDIX; + break; + } + ret_val = hw->phy.ops.write_reg(hw, IFE_PHY_MDIX_CONTROL, + reg_data); + if (ret_val) + goto out; + } + ret_val = e1000_setup_copper_link_generic(hw); + +out: + return ret_val; +} + +/** + * e1000_get_link_up_info_ich8lan - Get current link speed and duplex + * @hw: pointer to the HW structure + * @speed: pointer to store current link speed + * @duplex: pointer to store the current link duplex + * + * Calls the generic get_speed_and_duplex to retrieve the current link + * information and then calls the Kumeran lock loss workaround for links at + * gigabit speeds. + **/ +static s32 e1000_get_link_up_info_ich8lan(struct e1000_hw *hw, u16 *speed, + u16 *duplex) +{ + s32 ret_val; + + DEBUGFUNC("e1000_get_link_up_info_ich8lan"); + + ret_val = e1000_get_speed_and_duplex_copper_generic(hw, speed, duplex); + if (ret_val) + goto out; + + if ((hw->mac.type == e1000_ich8lan) && + (hw->phy.type == e1000_phy_igp_3) && + (*speed == SPEED_1000)) { + ret_val = e1000_kmrn_lock_loss_workaround_ich8lan(hw); + } + +out: + return ret_val; +} + +/** + * e1000_kmrn_lock_loss_workaround_ich8lan - Kumeran workaround + * @hw: pointer to the HW structure + * + * Work-around for 82566 Kumeran PCS lock loss: + * On link status change (i.e. PCI reset, speed change) and link is up and + * speed is gigabit- + * 0) if workaround is optionally disabled do nothing + * 1) wait 1ms for Kumeran link to come up + * 2) check Kumeran Diagnostic register PCS lock loss bit + * 3) if not set the link is locked (all is good), otherwise... + * 4) reset the PHY + * 5) repeat up to 10 times + * Note: this is only called for IGP3 copper when speed is 1gb. + **/ +static s32 e1000_kmrn_lock_loss_workaround_ich8lan(struct e1000_hw *hw) +{ + struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan; + u32 phy_ctrl; + s32 ret_val = E1000_SUCCESS; + u16 i, data; + bool link; + + DEBUGFUNC("e1000_kmrn_lock_loss_workaround_ich8lan"); + + if (!(dev_spec->kmrn_lock_loss_workaround_enabled)) + goto out; + + /* + * Make sure link is up before proceeding. If not just return. + * Attempting this while link is negotiating fouled up link + * stability + */ + ret_val = e1000_phy_has_link_generic(hw, 1, 0, &link); + if (!link) { + ret_val = E1000_SUCCESS; + goto out; + } + + for (i = 0; i < 10; i++) { + /* read once to clear */ + ret_val = hw->phy.ops.read_reg(hw, IGP3_KMRN_DIAG, &data); + if (ret_val) + goto out; + /* and again to get new status */ + ret_val = hw->phy.ops.read_reg(hw, IGP3_KMRN_DIAG, &data); + if (ret_val) + goto out; + + /* check for PCS lock */ + if (!(data & IGP3_KMRN_DIAG_PCS_LOCK_LOSS)) { + ret_val = E1000_SUCCESS; + goto out; + } + + /* Issue PHY reset */ + hw->phy.ops.reset(hw); + msec_delay_irq(5); + } + /* Disable GigE link negotiation */ + phy_ctrl = E1000_READ_REG(hw, E1000_PHY_CTRL); + phy_ctrl |= (E1000_PHY_CTRL_GBE_DISABLE | + E1000_PHY_CTRL_NOND0A_GBE_DISABLE); + E1000_WRITE_REG(hw, E1000_PHY_CTRL, phy_ctrl); + + /* + * Call gig speed drop workaround on Gig disable before accessing + * any PHY registers + */ + e1000_gig_downshift_workaround_ich8lan(hw); + + /* unable to acquire PCS lock */ + ret_val = -E1000_ERR_PHY; + +out: + return ret_val; +} + +/** + * e1000_set_kmrn_lock_loss_workaround_ich8lan - Set Kumeran workaround state + * @hw: pointer to the HW structure + * @state: boolean value used to set the current Kumeran workaround state + * + * If ICH8, set the current Kumeran workaround state (enabled - TRUE + * /disabled - FALSE). + **/ +void e1000_set_kmrn_lock_loss_workaround_ich8lan(struct e1000_hw *hw, + bool state) +{ + struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan; + + DEBUGFUNC("e1000_set_kmrn_lock_loss_workaround_ich8lan"); + + if (hw->mac.type != e1000_ich8lan) { + DEBUGOUT("Workaround applies to ICH8 only.\n"); + return; + } + + dev_spec->kmrn_lock_loss_workaround_enabled = state; + + return; +} + +/** + * e1000_ipg3_phy_powerdown_workaround_ich8lan - Power down workaround on D3 + * @hw: pointer to the HW structure + * + * Workaround for 82566 power-down on D3 entry: + * 1) disable gigabit link + * 2) write VR power-down enable + * 3) read it back + * Continue if successful, else issue LCD reset and repeat + **/ +void e1000_igp3_phy_powerdown_workaround_ich8lan(struct e1000_hw *hw) +{ + u32 reg; + u16 data; + u8 retry = 0; + + DEBUGFUNC("e1000_igp3_phy_powerdown_workaround_ich8lan"); + + if (hw->phy.type != e1000_phy_igp_3) + goto out; + + /* Try the workaround twice (if needed) */ + do { + /* Disable link */ + reg = E1000_READ_REG(hw, E1000_PHY_CTRL); + reg |= (E1000_PHY_CTRL_GBE_DISABLE | + E1000_PHY_CTRL_NOND0A_GBE_DISABLE); + E1000_WRITE_REG(hw, E1000_PHY_CTRL, reg); + + /* + * Call gig speed drop workaround on Gig disable before + * accessing any PHY registers + */ + if (hw->mac.type == e1000_ich8lan) + e1000_gig_downshift_workaround_ich8lan(hw); + + /* Write VR power-down enable */ + hw->phy.ops.read_reg(hw, IGP3_VR_CTRL, &data); + data &= ~IGP3_VR_CTRL_DEV_POWERDOWN_MODE_MASK; + hw->phy.ops.write_reg(hw, IGP3_VR_CTRL, + data | IGP3_VR_CTRL_MODE_SHUTDOWN); + + /* Read it back and test */ + hw->phy.ops.read_reg(hw, IGP3_VR_CTRL, &data); + data &= IGP3_VR_CTRL_DEV_POWERDOWN_MODE_MASK; + if ((data == IGP3_VR_CTRL_MODE_SHUTDOWN) || retry) + break; + + /* Issue PHY reset and repeat at most one more time */ + reg = E1000_READ_REG(hw, E1000_CTRL); + E1000_WRITE_REG(hw, E1000_CTRL, reg | E1000_CTRL_PHY_RST); + retry++; + } while (retry); + +out: + return; +} + +/** + * e1000_gig_downshift_workaround_ich8lan - WoL from S5 stops working + * @hw: pointer to the HW structure + * + * Steps to take when dropping from 1Gb/s (eg. link cable removal (LSC), + * LPLU, Gig disable, MDIC PHY reset): + * 1) Set Kumeran Near-end loopback + * 2) Clear Kumeran Near-end loopback + * Should only be called for ICH8[m] devices with IGP_3 Phy. + **/ +void e1000_gig_downshift_workaround_ich8lan(struct e1000_hw *hw) +{ + s32 ret_val = E1000_SUCCESS; + u16 reg_data; + + DEBUGFUNC("e1000_gig_downshift_workaround_ich8lan"); + + if ((hw->mac.type != e1000_ich8lan) || + (hw->phy.type != e1000_phy_igp_3)) + goto out; + + ret_val = e1000_read_kmrn_reg_generic(hw, E1000_KMRNCTRLSTA_DIAG_OFFSET, + ®_data); + if (ret_val) + goto out; + reg_data |= E1000_KMRNCTRLSTA_DIAG_NELPBK; + ret_val = e1000_write_kmrn_reg_generic(hw, + E1000_KMRNCTRLSTA_DIAG_OFFSET, + reg_data); + if (ret_val) + goto out; + reg_data &= ~E1000_KMRNCTRLSTA_DIAG_NELPBK; + ret_val = e1000_write_kmrn_reg_generic(hw, + E1000_KMRNCTRLSTA_DIAG_OFFSET, + reg_data); +out: + return; +} + +/** + * e1000_disable_gig_wol_ich8lan - disable gig during WoL + * @hw: pointer to the HW structure + * + * During S0 to Sx transition, it is possible the link remains at gig + * instead of negotiating to a lower speed. Before going to Sx, set + * 'LPLU Enabled' and 'Gig Disable' to force link speed negotiation + * to a lower speed. + * + * Should only be called for ICH9 and ICH10 devices. + **/ +void e1000_disable_gig_wol_ich8lan(struct e1000_hw *hw) +{ + u32 phy_ctrl; + + if ((hw->mac.type == e1000_ich10lan) || + (hw->mac.type == e1000_ich9lan)) { + phy_ctrl = E1000_READ_REG(hw, E1000_PHY_CTRL); + phy_ctrl |= E1000_PHY_CTRL_D0A_LPLU | + E1000_PHY_CTRL_GBE_DISABLE; + E1000_WRITE_REG(hw, E1000_PHY_CTRL, phy_ctrl); + } + + return; +} + +/** + * e1000_cleanup_led_ich8lan - Restore the default LED operation + * @hw: pointer to the HW structure + * + * Return the LED back to the default configuration. + **/ +static s32 e1000_cleanup_led_ich8lan(struct e1000_hw *hw) +{ + s32 ret_val = E1000_SUCCESS; + + DEBUGFUNC("e1000_cleanup_led_ich8lan"); + + if (hw->phy.type == e1000_phy_ife) + ret_val = hw->phy.ops.write_reg(hw, IFE_PHY_SPECIAL_CONTROL_LED, + 0); + else + E1000_WRITE_REG(hw, E1000_LEDCTL, hw->mac.ledctl_default); + + return ret_val; +} + +/** + * e1000_led_on_ich8lan - Turn LEDs on + * @hw: pointer to the HW structure + * + * Turn on the LEDs. + **/ +static s32 e1000_led_on_ich8lan(struct e1000_hw *hw) +{ + s32 ret_val = E1000_SUCCESS; + + DEBUGFUNC("e1000_led_on_ich8lan"); + + if (hw->phy.type == e1000_phy_ife) + ret_val = hw->phy.ops.write_reg(hw, IFE_PHY_SPECIAL_CONTROL_LED, + (IFE_PSCL_PROBE_MODE | IFE_PSCL_PROBE_LEDS_ON)); + else + E1000_WRITE_REG(hw, E1000_LEDCTL, hw->mac.ledctl_mode2); + + return ret_val; +} + +/** + * e1000_led_off_ich8lan - Turn LEDs off + * @hw: pointer to the HW structure + * + * Turn off the LEDs. + **/ +static s32 e1000_led_off_ich8lan(struct e1000_hw *hw) +{ + s32 ret_val = E1000_SUCCESS; + + DEBUGFUNC("e1000_led_off_ich8lan"); + + if (hw->phy.type == e1000_phy_ife) + ret_val = hw->phy.ops.write_reg(hw, + IFE_PHY_SPECIAL_CONTROL_LED, + (IFE_PSCL_PROBE_MODE | IFE_PSCL_PROBE_LEDS_OFF)); + else + E1000_WRITE_REG(hw, E1000_LEDCTL, hw->mac.ledctl_mode1); + + return ret_val; +} + +/** + * e1000_get_cfg_done_ich8lan - Read config done bit + * @hw: pointer to the HW structure + * + * Read the management control register for the config done bit for + * completion status. NOTE: silicon which is EEPROM-less will fail trying + * to read the config done bit, so an error is *ONLY* logged and returns + * E1000_SUCCESS. If we were to return with error, EEPROM-less silicon + * would not be able to be reset or change link. + **/ +static s32 e1000_get_cfg_done_ich8lan(struct e1000_hw *hw) +{ + s32 ret_val = E1000_SUCCESS; + u32 bank = 0; + + e1000_get_cfg_done_generic(hw); + + /* If EEPROM is not marked present, init the IGP 3 PHY manually */ + if (hw->mac.type != e1000_ich10lan) { + if (((E1000_READ_REG(hw, E1000_EECD) & E1000_EECD_PRES) == 0) && + (hw->phy.type == e1000_phy_igp_3)) { + e1000_phy_init_script_igp3(hw); + } + } else { + if (e1000_valid_nvm_bank_detect_ich8lan(hw, &bank)) { + /* Maybe we should do a basic PHY config */ + DEBUGOUT("EEPROM not present\n"); + ret_val = -E1000_ERR_CONFIG; + } + } + + return ret_val; +} + +/** + * e1000_power_down_phy_copper_ich8lan - Remove link during PHY power down + * @hw: pointer to the HW structure + * + * In the case of a PHY power down to save power, or to turn off link during a + * driver unload, or wake on lan is not enabled, remove the link. + **/ +static void e1000_power_down_phy_copper_ich8lan(struct e1000_hw *hw) +{ + /* If the management interface is not enabled, then power down */ + if (!(hw->mac.ops.check_mng_mode(hw) || + hw->phy.ops.check_reset_block(hw))) + e1000_power_down_phy_copper(hw); + + return; +} + +/** + * e1000_clear_hw_cntrs_ich8lan - Clear statistical counters + * @hw: pointer to the HW structure + * + * Clears hardware counters specific to the silicon family and calls + * clear_hw_cntrs_generic to clear all general purpose counters. + **/ +static void e1000_clear_hw_cntrs_ich8lan(struct e1000_hw *hw) +{ + DEBUGFUNC("e1000_clear_hw_cntrs_ich8lan"); + + e1000_clear_hw_cntrs_base_generic(hw); + + E1000_READ_REG(hw, E1000_ALGNERRC); + E1000_READ_REG(hw, E1000_RXERRC); + E1000_READ_REG(hw, E1000_TNCRS); + E1000_READ_REG(hw, E1000_CEXTERR); + E1000_READ_REG(hw, E1000_TSCTC); + E1000_READ_REG(hw, E1000_TSCTFC); + + E1000_READ_REG(hw, E1000_MGTPRC); + E1000_READ_REG(hw, E1000_MGTPDC); + E1000_READ_REG(hw, E1000_MGTPTC); + + E1000_READ_REG(hw, E1000_IAC); + E1000_READ_REG(hw, E1000_ICRXOC); +} + diff --git a/sys/dev/netif/ig_hal/e1000_ich8lan.h b/sys/dev/netif/ig_hal/e1000_ich8lan.h new file mode 100644 index 0000000000..79dffcdea5 --- /dev/null +++ b/sys/dev/netif/ig_hal/e1000_ich8lan.h @@ -0,0 +1,132 @@ +/****************************************************************************** + + Copyright (c) 2001-2008, Intel Corporation + All rights reserved. + + Redistribution and use in source and binary forms, with or without + modification, are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, + this list of conditions and the following disclaimer. + + 2. Redistributions in binary form must reproduce the above copyright + notice, this list of conditions and the following disclaimer in the + documentation and/or other materials provided with the distribution. + + 3. Neither the name of the Intel Corporation nor the names of its + contributors may be used to endorse or promote products derived from + this software without specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE + ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE + LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR + CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF + SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS + INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN + CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) + ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + POSSIBILITY OF SUCH DAMAGE. + +******************************************************************************/ +/*$FreeBSD$*/ + +#ifndef _E1000_ICH8LAN_H_ +#define _E1000_ICH8LAN_H_ + +#define ICH_FLASH_GFPREG 0x0000 +#define ICH_FLASH_HSFSTS 0x0004 +#define ICH_FLASH_HSFCTL 0x0006 +#define ICH_FLASH_FADDR 0x0008 +#define ICH_FLASH_FDATA0 0x0010 + +#define ICH_FLASH_READ_COMMAND_TIMEOUT 500 +#define ICH_FLASH_WRITE_COMMAND_TIMEOUT 500 +#define ICH_FLASH_ERASE_COMMAND_TIMEOUT 3000000 +#define ICH_FLASH_LINEAR_ADDR_MASK 0x00FFFFFF +#define ICH_FLASH_CYCLE_REPEAT_COUNT 10 + +#define ICH_CYCLE_READ 0 +#define ICH_CYCLE_WRITE 2 +#define ICH_CYCLE_ERASE 3 + +#define FLASH_GFPREG_BASE_MASK 0x1FFF +#define FLASH_SECTOR_ADDR_SHIFT 12 + +#define ICH_FLASH_SEG_SIZE_256 256 +#define ICH_FLASH_SEG_SIZE_4K 4096 +#define ICH_FLASH_SEG_SIZE_8K 8192 +#define ICH_FLASH_SEG_SIZE_64K 65536 +#define ICH_FLASH_SECTOR_SIZE 4096 + +#define ICH_FLASH_REG_MAPSIZE 0x00A0 + +#define E1000_ICH_FWSM_RSPCIPHY 0x00000040 /* Reset PHY on PCI Reset */ +#define E1000_ICH_FWSM_DISSW 0x10000000 /* FW Disables SW Writes */ +/* FW established a valid mode */ +#define E1000_ICH_FWSM_FW_VALID 0x00008000 + +#define E1000_ICH_MNG_IAMT_MODE 0x2 + +#define ID_LED_DEFAULT_ICH8LAN ((ID_LED_DEF1_DEF2 << 12) | \ + (ID_LED_DEF1_OFF2 << 8) | \ + (ID_LED_DEF1_ON2 << 4) | \ + (ID_LED_DEF1_DEF2)) + +#define E1000_ICH_NVM_SIG_WORD 0x13 +#define E1000_ICH_NVM_SIG_MASK 0xC000 + +#define E1000_ICH8_LAN_INIT_TIMEOUT 1500 + +#define E1000_FEXTNVM_SW_CONFIG 1 +#define E1000_FEXTNVM_SW_CONFIG_ICH8M (1 << 27) /* Bit redefined for ICH8M */ + +#define PCIE_ICH8_SNOOP_ALL PCIE_NO_SNOOP_ALL + +#define E1000_ICH_RAR_ENTRIES 7 + +#define PHY_PAGE_SHIFT 5 +#define PHY_REG(page, reg) (((page) << PHY_PAGE_SHIFT) | \ + ((reg) & MAX_PHY_REG_ADDRESS)) +#define IGP3_KMRN_DIAG PHY_REG(770, 19) /* KMRN Diagnostic */ +#define IGP3_VR_CTRL PHY_REG(776, 18) /* Voltage Regulator Control */ +#define IGP3_CAPABILITY PHY_REG(776, 19) /* Capability */ +#define IGP3_PM_CTRL PHY_REG(769, 20) /* Power Management Control */ + +#define IGP3_KMRN_DIAG_PCS_LOCK_LOSS 0x0002 +#define IGP3_VR_CTRL_DEV_POWERDOWN_MODE_MASK 0x0300 +#define IGP3_VR_CTRL_MODE_SHUTDOWN 0x0200 +#define IGP3_PM_CTRL_FORCE_PWR_DOWN 0x0020 + +/* + * Additional interrupts need to be handled for ICH family: + * DSW = The FW changed the status of the DISSW bit in FWSM + * PHYINT = The LAN connected device generates an interrupt + * EPRST = Manageability reset event + */ +#define IMS_ICH_ENABLE_MASK (\ + E1000_IMS_DSW | \ + E1000_IMS_PHYINT | \ + E1000_IMS_EPRST) + +/* Additional interrupt register bit definitions */ +#define E1000_ICR_LSECPNC 0x00004000 /* PN threshold - client */ +#define E1000_IMS_LSECPNC E1000_ICR_LSECPNC /* PN threshold - client */ +#define E1000_ICS_LSECPNC E1000_ICR_LSECPNC /* PN threshold - client */ + +/* Security Processing bit Indication */ +#define E1000_RXDEXT_LINKSEC_STATUS_LSECH 0x01000000 +#define E1000_RXDEXT_LINKSEC_ERROR_BIT_MASK 0x60000000 +#define E1000_RXDEXT_LINKSEC_ERROR_NO_SA_MATCH 0x20000000 +#define E1000_RXDEXT_LINKSEC_ERROR_REPLAY_ERROR 0x40000000 +#define E1000_RXDEXT_LINKSEC_ERROR_BAD_SIG 0x60000000 + + +void e1000_set_kmrn_lock_loss_workaround_ich8lan(struct e1000_hw *hw, + bool state); +void e1000_igp3_phy_powerdown_workaround_ich8lan(struct e1000_hw *hw); +void e1000_gig_downshift_workaround_ich8lan(struct e1000_hw *hw); +void e1000_disable_gig_wol_ich8lan(struct e1000_hw *hw); + +#endif diff --git a/sys/dev/netif/ig_hal/e1000_mac.c b/sys/dev/netif/ig_hal/e1000_mac.c new file mode 100644 index 0000000000..fcec3423c9 --- /dev/null +++ b/sys/dev/netif/ig_hal/e1000_mac.c @@ -0,0 +1,2216 @@ +/****************************************************************************** + + Copyright (c) 2001-2008, Intel Corporation + All rights reserved. + + Redistribution and use in source and binary forms, with or without + modification, are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, + this list of conditions and the following disclaimer. + + 2. Redistributions in binary form must reproduce the above copyright + notice, this list of conditions and the following disclaimer in the + documentation and/or other materials provided with the distribution. + + 3. Neither the name of the Intel Corporation nor the names of its + contributors may be used to endorse or promote products derived from + this software without specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE + ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE + LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR + CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF + SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS + INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN + CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) + ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + POSSIBILITY OF SUCH DAMAGE. + +******************************************************************************/ +/*$FreeBSD$*/ + +#include "e1000_api.h" + +static s32 e1000_validate_mdi_setting_generic(struct e1000_hw *hw); + +/** + * e1000_init_mac_ops_generic - Initialize MAC function pointers + * @hw: pointer to the HW structure + * + * Setups up the function pointers to no-op functions + **/ +void e1000_init_mac_ops_generic(struct e1000_hw *hw) +{ + struct e1000_mac_info *mac = &hw->mac; + DEBUGFUNC("e1000_init_mac_ops_generic"); + + /* General Setup */ + mac->ops.init_params = e1000_null_ops_generic; + mac->ops.init_hw = e1000_null_ops_generic; + mac->ops.reset_hw = e1000_null_ops_generic; + mac->ops.setup_physical_interface = e1000_null_ops_generic; + mac->ops.get_bus_info = e1000_null_ops_generic; + mac->ops.set_lan_id = e1000_set_lan_id_multi_port_pcie; + mac->ops.read_mac_addr = e1000_read_mac_addr_generic; + mac->ops.config_collision_dist = e1000_config_collision_dist_generic; + mac->ops.clear_hw_cntrs = e1000_null_mac_generic; + /* LED */ + mac->ops.cleanup_led = e1000_null_ops_generic; + mac->ops.setup_led = e1000_null_ops_generic; + mac->ops.blink_led = e1000_null_ops_generic; + mac->ops.led_on = e1000_null_ops_generic; + mac->ops.led_off = e1000_null_ops_generic; + /* LINK */ + mac->ops.setup_link = e1000_null_ops_generic; + mac->ops.get_link_up_info = e1000_null_link_info; + mac->ops.check_for_link = e1000_null_ops_generic; + mac->ops.wait_autoneg = e1000_wait_autoneg_generic; + /* Management */ + mac->ops.check_mng_mode = e1000_null_mng_mode; + mac->ops.mng_host_if_write = e1000_mng_host_if_write_generic; + mac->ops.mng_write_cmd_header = e1000_mng_write_cmd_header_generic; + mac->ops.mng_enable_host_if = e1000_mng_enable_host_if_generic; + /* VLAN, MC, etc. */ + mac->ops.update_mc_addr_list = e1000_null_update_mc; + mac->ops.clear_vfta = e1000_null_mac_generic; + mac->ops.write_vfta = e1000_null_write_vfta; + mac->ops.mta_set = e1000_null_mta_set; + mac->ops.rar_set = e1000_rar_set_generic; + mac->ops.validate_mdi_setting = e1000_validate_mdi_setting_generic; +} + +/** + * e1000_null_ops_generic - No-op function, returns 0 + * @hw: pointer to the HW structure + **/ +s32 e1000_null_ops_generic(struct e1000_hw *hw) +{ + DEBUGFUNC("e1000_null_ops_generic"); + return E1000_SUCCESS; +} + +/** + * e1000_null_mac_generic - No-op function, return void + * @hw: pointer to the HW structure + **/ +void e1000_null_mac_generic(struct e1000_hw *hw) +{ + DEBUGFUNC("e1000_null_mac_generic"); + return; +} + +/** + * e1000_null_link_info - No-op function, return 0 + * @hw: pointer to the HW structure + **/ +s32 e1000_null_link_info(struct e1000_hw *hw, u16 *s, u16 *d) +{ + DEBUGFUNC("e1000_null_link_info"); + return E1000_SUCCESS; +} + +/** + * e1000_null_mng_mode - No-op function, return FALSE + * @hw: pointer to the HW structure + **/ +bool e1000_null_mng_mode(struct e1000_hw *hw) +{ + DEBUGFUNC("e1000_null_mng_mode"); + return FALSE; +} + +/** + * e1000_null_update_mc - No-op function, return void + * @hw: pointer to the HW structure + **/ +void e1000_null_update_mc(struct e1000_hw *hw, u8 *h, u32 a, u32 b, u32 c) +{ + DEBUGFUNC("e1000_null_update_mc"); + return; +} + +/** + * e1000_null_write_vfta - No-op function, return void + * @hw: pointer to the HW structure + **/ +void e1000_null_write_vfta(struct e1000_hw *hw, u32 a, u32 b) +{ + DEBUGFUNC("e1000_null_write_vfta"); + return; +} + +/** + * e1000_null_set_mta - No-op function, return void + * @hw: pointer to the HW structure + **/ +void e1000_null_mta_set(struct e1000_hw *hw, u32 a) +{ + DEBUGFUNC("e1000_null_mta_set"); + return; +} + +/** + * e1000_null_rar_set - No-op function, return void + * @hw: pointer to the HW structure + **/ +void e1000_null_rar_set(struct e1000_hw *hw, u8 *h, u32 a) +{ + DEBUGFUNC("e1000_null_rar_set"); + return; +} + +/** + * e1000_get_bus_info_pci_generic - Get PCI(x) bus information + * @hw: pointer to the HW structure + * + * Determines and stores the system bus information for a particular + * network interface. The following bus information is determined and stored: + * bus speed, bus width, type (PCI/PCIx), and PCI(-x) function. + **/ +s32 e1000_get_bus_info_pci_generic(struct e1000_hw *hw) +{ + struct e1000_mac_info *mac = &hw->mac; + struct e1000_bus_info *bus = &hw->bus; + u32 status = E1000_READ_REG(hw, E1000_STATUS); + s32 ret_val = E1000_SUCCESS; + + DEBUGFUNC("e1000_get_bus_info_pci_generic"); + + /* PCI or PCI-X? */ + bus->type = (status & E1000_STATUS_PCIX_MODE) + ? e1000_bus_type_pcix + : e1000_bus_type_pci; + + /* Bus speed */ + if (bus->type == e1000_bus_type_pci) { + bus->speed = (status & E1000_STATUS_PCI66) + ? e1000_bus_speed_66 + : e1000_bus_speed_33; + } else { + switch (status & E1000_STATUS_PCIX_SPEED) { + case E1000_STATUS_PCIX_SPEED_66: + bus->speed = e1000_bus_speed_66; + break; + case E1000_STATUS_PCIX_SPEED_100: + bus->speed = e1000_bus_speed_100; + break; + case E1000_STATUS_PCIX_SPEED_133: + bus->speed = e1000_bus_speed_133; + break; + default: + bus->speed = e1000_bus_speed_reserved; + break; + } + } + + /* Bus width */ + bus->width = (status & E1000_STATUS_BUS64) + ? e1000_bus_width_64 + : e1000_bus_width_32; + + /* Which PCI(-X) function? */ + mac->ops.set_lan_id(hw); + + return ret_val; +} + +/** + * e1000_get_bus_info_pcie_generic - Get PCIe bus information + * @hw: pointer to the HW structure + * + * Determines and stores the system bus information for a particular + * network interface. The following bus information is determined and stored: + * bus speed, bus width, type (PCIe), and PCIe function. + **/ +s32 e1000_get_bus_info_pcie_generic(struct e1000_hw *hw) +{ + struct e1000_mac_info *mac = &hw->mac; + struct e1000_bus_info *bus = &hw->bus; + + s32 ret_val; + u16 pcie_link_status; + + DEBUGFUNC("e1000_get_bus_info_pcie_generic"); + + bus->type = e1000_bus_type_pci_express; + bus->speed = e1000_bus_speed_2500; + + ret_val = e1000_read_pcie_cap_reg(hw, + PCIE_LINK_STATUS, + &pcie_link_status); + if (ret_val) + bus->width = e1000_bus_width_unknown; + else + bus->width = (enum e1000_bus_width)((pcie_link_status & + PCIE_LINK_WIDTH_MASK) >> + PCIE_LINK_WIDTH_SHIFT); + + mac->ops.set_lan_id(hw); + + return E1000_SUCCESS; +} + +/** + * e1000_set_lan_id_multi_port_pcie - Set LAN id for PCIe multiple port devices + * + * @hw: pointer to the HW structure + * + * Determines the LAN function id by reading memory-mapped registers + * and swaps the port value if requested. + **/ +void e1000_set_lan_id_multi_port_pcie(struct e1000_hw *hw) +{ + struct e1000_bus_info *bus = &hw->bus; + u32 reg; + + reg = E1000_READ_REG(hw, E1000_STATUS); + bus->func = (reg & E1000_STATUS_FUNC_MASK) >> E1000_STATUS_FUNC_SHIFT; + + /* check for a port swap */ + reg = E1000_READ_REG(hw, E1000_FACTPS); + if (reg & E1000_FACTPS_LFS) + bus->func ^= 0x1; +} + +/** + * e1000_set_lan_id_multi_port_pci - Set LAN id for PCI multiple port devices + * @hw: pointer to the HW structure + * + * Determines the LAN function id by reading PCI config space. + **/ +void e1000_set_lan_id_multi_port_pci(struct e1000_hw *hw) +{ + struct e1000_bus_info *bus = &hw->bus; + u16 pci_header_type; + u32 status; + + e1000_read_pci_cfg(hw, PCI_HEADER_TYPE_REGISTER, &pci_header_type); + if (pci_header_type & PCI_HEADER_TYPE_MULTIFUNC) { + status = E1000_READ_REG(hw, E1000_STATUS); + bus->func = (status & E1000_STATUS_FUNC_MASK) + >> E1000_STATUS_FUNC_SHIFT; + } else { + bus->func = 0; + } +} + +/** + * e1000_set_lan_id_single_port - Set LAN id for a single port device + * @hw: pointer to the HW structure + * + * Sets the LAN function id to zero for a single port device. + **/ +void e1000_set_lan_id_single_port(struct e1000_hw *hw) +{ + struct e1000_bus_info *bus = &hw->bus; + + bus->func = 0; +} + +/** + * e1000_clear_vfta_generic - Clear VLAN filter table + * @hw: pointer to the HW structure + * + * Clears the register array which contains the VLAN filter table by + * setting all the values to 0. + **/ +void e1000_clear_vfta_generic(struct e1000_hw *hw) +{ + u32 offset; + + DEBUGFUNC("e1000_clear_vfta_generic"); + + for (offset = 0; offset < E1000_VLAN_FILTER_TBL_SIZE; offset++) { + E1000_WRITE_REG_ARRAY(hw, E1000_VFTA, offset, 0); + E1000_WRITE_FLUSH(hw); + } +} + +/** + * e1000_write_vfta_generic - Write value to VLAN filter table + * @hw: pointer to the HW structure + * @offset: register offset in VLAN filter table + * @value: register value written to VLAN filter table + * + * Writes value at the given offset in the register array which stores + * the VLAN filter table. + **/ +void e1000_write_vfta_generic(struct e1000_hw *hw, u32 offset, u32 value) +{ + DEBUGFUNC("e1000_write_vfta_generic"); + + E1000_WRITE_REG_ARRAY(hw, E1000_VFTA, offset, value); + E1000_WRITE_FLUSH(hw); +} + +/** + * e1000_init_rx_addrs_generic - Initialize receive address's + * @hw: pointer to the HW structure + * @rar_count: receive address registers + * + * Setups the receive address registers by setting the base receive address + * register to the devices MAC address and clearing all the other receive + * address registers to 0. + **/ +void e1000_init_rx_addrs_generic(struct e1000_hw *hw, u16 rar_count) +{ + u32 i; + + DEBUGFUNC("e1000_init_rx_addrs_generic"); + + /* Setup the receive address */ + DEBUGOUT("Programming MAC Address into RAR[0]\n"); + + hw->mac.ops.rar_set(hw, hw->mac.addr, 0); + + /* Zero out the other (rar_entry_count - 1) receive addresses */ + DEBUGOUT1("Clearing RAR[1-%u]\n", rar_count-1); + for (i = 1; i < rar_count; i++) { + E1000_WRITE_REG_ARRAY(hw, E1000_RA, (i << 1), 0); + E1000_WRITE_FLUSH(hw); + E1000_WRITE_REG_ARRAY(hw, E1000_RA, ((i << 1) + 1), 0); + E1000_WRITE_FLUSH(hw); + } +} + +/** + * e1000_check_alt_mac_addr_generic - Check for alternate MAC addr + * @hw: pointer to the HW structure + * + * Checks the nvm for an alternate MAC address. An alternate MAC address + * can be setup by pre-boot software and must be treated like a permanent + * address and must override the actual permanent MAC address. If an + * alternate MAC address is found it is saved in the hw struct and + * programmed into RAR0 and the function returns success, otherwise the + * function returns an error. + **/ +s32 e1000_check_alt_mac_addr_generic(struct e1000_hw *hw) +{ + u32 i; + s32 ret_val = E1000_SUCCESS; + u16 offset, nvm_alt_mac_addr_offset, nvm_data; + u8 alt_mac_addr[ETH_ADDR_LEN]; + + DEBUGFUNC("e1000_check_alt_mac_addr_generic"); + + ret_val = hw->nvm.ops.read(hw, NVM_ALT_MAC_ADDR_PTR, 1, + &nvm_alt_mac_addr_offset); + if (ret_val) { + DEBUGOUT("NVM Read Error\n"); + goto out; + } + + if (nvm_alt_mac_addr_offset == 0xFFFF) { + ret_val = -(E1000_NOT_IMPLEMENTED); + goto out; + } + + if (hw->bus.func == E1000_FUNC_1) + nvm_alt_mac_addr_offset += ETH_ADDR_LEN/sizeof(u16); + + for (i = 0; i < ETH_ADDR_LEN; i += 2) { + offset = nvm_alt_mac_addr_offset + (i >> 1); + ret_val = hw->nvm.ops.read(hw, offset, 1, &nvm_data); + if (ret_val) { + DEBUGOUT("NVM Read Error\n"); + goto out; + } + + alt_mac_addr[i] = (u8)(nvm_data & 0xFF); + alt_mac_addr[i + 1] = (u8)(nvm_data >> 8); + } + + /* if multicast bit is set, the alternate address will not be used */ + if (alt_mac_addr[0] & 0x01) { + ret_val = -(E1000_NOT_IMPLEMENTED); + goto out; + } + + for (i = 0; i < ETH_ADDR_LEN; i++) + hw->mac.addr[i] = hw->mac.perm_addr[i] = alt_mac_addr[i]; + + hw->mac.ops.rar_set(hw, hw->mac.perm_addr, 0); + +out: + return ret_val; +} + +/** + * e1000_rar_set_generic - Set receive address register + * @hw: pointer to the HW structure + * @addr: pointer to the receive address + * @index: receive address array register + * + * Sets the receive address array register at index to the address passed + * in by addr. + **/ +void e1000_rar_set_generic(struct e1000_hw *hw, u8 *addr, u32 index) +{ + u32 rar_low, rar_high; + + DEBUGFUNC("e1000_rar_set_generic"); + + /* + * HW expects these in little endian so we reverse the byte order + * from network order (big endian) to little endian + */ + rar_low = ((u32) addr[0] | + ((u32) addr[1] << 8) | + ((u32) addr[2] << 16) | ((u32) addr[3] << 24)); + + rar_high = ((u32) addr[4] | ((u32) addr[5] << 8)); + + /* If MAC address zero, no need to set the AV bit */ + if (rar_low || rar_high) + rar_high |= E1000_RAH_AV; + + E1000_WRITE_REG(hw, E1000_RAL(index), rar_low); + E1000_WRITE_REG(hw, E1000_RAH(index), rar_high); +} + +/** + * e1000_mta_set_generic - Set multicast filter table address + * @hw: pointer to the HW structure + * @hash_value: determines the MTA register and bit to set + * + * The multicast table address is a register array of 32-bit registers. + * The hash_value is used to determine what register the bit is in, the + * current value is read, the new bit is OR'd in and the new value is + * written back into the register. + **/ +void e1000_mta_set_generic(struct e1000_hw *hw, u32 hash_value) +{ + u32 hash_bit, hash_reg, mta; + + DEBUGFUNC("e1000_mta_set_generic"); + /* + * The MTA is a register array of 32-bit registers. It is + * treated like an array of (32*mta_reg_count) bits. We want to + * set bit BitArray[hash_value]. So we figure out what register + * the bit is in, read it, OR in the new bit, then write + * back the new value. The (hw->mac.mta_reg_count - 1) serves as a + * mask to bits 31:5 of the hash value which gives us the + * register we're modifying. The hash bit within that register + * is determined by the lower 5 bits of the hash value. + */ + hash_reg = (hash_value >> 5) & (hw->mac.mta_reg_count - 1); + hash_bit = hash_value & 0x1F; + + mta = E1000_READ_REG_ARRAY(hw, E1000_MTA, hash_reg); + + mta |= (1 << hash_bit); + + E1000_WRITE_REG_ARRAY(hw, E1000_MTA, hash_reg, mta); + E1000_WRITE_FLUSH(hw); +} + +/** + * e1000_update_mc_addr_list_generic - Update Multicast addresses + * @hw: pointer to the HW structure + * @mc_addr_list: array of multicast addresses to program + * @mc_addr_count: number of multicast addresses to program + * @rar_used_count: the first RAR register free to program + * @rar_count: total number of supported Receive Address Registers + * + * Updates the Receive Address Registers and Multicast Table Array. + * The caller must have a packed mc_addr_list of multicast addresses. + * The parameter rar_count will usually be hw->mac.rar_entry_count + * unless there are workarounds that change this. + **/ +void e1000_update_mc_addr_list_generic(struct e1000_hw *hw, + u8 *mc_addr_list, u32 mc_addr_count, + u32 rar_used_count, u32 rar_count) +{ + u32 hash_value; + u32 i; + + DEBUGFUNC("e1000_update_mc_addr_list_generic"); + + /* + * Load the first set of multicast addresses into the exact + * filters (RAR). If there are not enough to fill the RAR + * array, clear the filters. + */ + for (i = rar_used_count; i < rar_count; i++) { + if (mc_addr_count) { + hw->mac.ops.rar_set(hw, mc_addr_list, i); + mc_addr_count--; + mc_addr_list += ETH_ADDR_LEN; + } else { + E1000_WRITE_REG_ARRAY(hw, E1000_RA, i << 1, 0); + E1000_WRITE_FLUSH(hw); + E1000_WRITE_REG_ARRAY(hw, E1000_RA, (i << 1) + 1, 0); + E1000_WRITE_FLUSH(hw); + } + } + + /* Clear the old settings from the MTA */ + DEBUGOUT("Clearing MTA\n"); + for (i = 0; i < hw->mac.mta_reg_count; i++) { + E1000_WRITE_REG_ARRAY(hw, E1000_MTA, i, 0); + E1000_WRITE_FLUSH(hw); + } + + /* Load any remaining multicast addresses into the hash table. */ + for (; mc_addr_count > 0; mc_addr_count--) { + hash_value = e1000_hash_mc_addr_generic(hw, mc_addr_list); + DEBUGOUT1("Hash value = 0x%03X\n", hash_value); + hw->mac.ops.mta_set(hw, hash_value); + mc_addr_list += ETH_ADDR_LEN; + } +} + +/** + * e1000_hash_mc_addr_generic - Generate a multicast hash value + * @hw: pointer to the HW structure + * @mc_addr: pointer to a multicast address + * + * Generates a multicast address hash value which is used to determine + * the multicast filter table array address and new table value. See + * e1000_mta_set_generic() + **/ +u32 e1000_hash_mc_addr_generic(struct e1000_hw *hw, u8 *mc_addr) +{ + u32 hash_value, hash_mask; + u8 bit_shift = 0; + + DEBUGFUNC("e1000_hash_mc_addr_generic"); + + /* Register count multiplied by bits per register */ + hash_mask = (hw->mac.mta_reg_count * 32) - 1; + + /* + * For a mc_filter_type of 0, bit_shift is the number of left-shifts + * where 0xFF would still fall within the hash mask. + */ + while (hash_mask >> bit_shift != 0xFF) + bit_shift++; + + /* + * The portion of the address that is used for the hash table + * is determined by the mc_filter_type setting. + * The algorithm is such that there is a total of 8 bits of shifting. + * The bit_shift for a mc_filter_type of 0 represents the number of + * left-shifts where the MSB of mc_addr[5] would still fall within + * the hash_mask. Case 0 does this exactly. Since there are a total + * of 8 bits of shifting, then mc_addr[4] will shift right the + * remaining number of bits. Thus 8 - bit_shift. The rest of the + * cases are a variation of this algorithm...essentially raising the + * number of bits to shift mc_addr[5] left, while still keeping the + * 8-bit shifting total. + * + * For example, given the following Destination MAC Address and an + * mta register count of 128 (thus a 4096-bit vector and 0xFFF mask), + * we can see that the bit_shift for case 0 is 4. These are the hash + * values resulting from each mc_filter_type... + * [0] [1] [2] [3] [4] [5] + * 01 AA 00 12 34 56 + * LSB MSB + * + * case 0: hash_value = ((0x34 >> 4) | (0x56 << 4)) & 0xFFF = 0x563 + * case 1: hash_value = ((0x34 >> 3) | (0x56 << 5)) & 0xFFF = 0xAC6 + * case 2: hash_value = ((0x34 >> 2) | (0x56 << 6)) & 0xFFF = 0x163 + * case 3: hash_value = ((0x34 >> 0) | (0x56 << 8)) & 0xFFF = 0x634 + */ + switch (hw->mac.mc_filter_type) { + default: + case 0: + break; + case 1: + bit_shift += 1; + break; + case 2: + bit_shift += 2; + break; + case 3: + bit_shift += 4; + break; + } + + hash_value = hash_mask & (((mc_addr[4] >> (8 - bit_shift)) | + (((u16) mc_addr[5]) << bit_shift))); + + return hash_value; +} + +/** + * e1000_pcix_mmrbc_workaround_generic - Fix incorrect MMRBC value + * @hw: pointer to the HW structure + * + * In certain situations, a system BIOS may report that the PCIx maximum + * memory read byte count (MMRBC) value is higher than than the actual + * value. We check the PCIx command register with the current PCIx status + * register. + **/ +void e1000_pcix_mmrbc_workaround_generic(struct e1000_hw *hw) +{ + u16 cmd_mmrbc; + u16 pcix_cmd; + u16 pcix_stat_hi_word; + u16 stat_mmrbc; + + DEBUGFUNC("e1000_pcix_mmrbc_workaround_generic"); + + /* Workaround for PCI-X issue when BIOS sets MMRBC incorrectly */ + if (hw->bus.type != e1000_bus_type_pcix) + return; + + e1000_read_pci_cfg(hw, PCIX_COMMAND_REGISTER, &pcix_cmd); + e1000_read_pci_cfg(hw, PCIX_STATUS_REGISTER_HI, &pcix_stat_hi_word); + cmd_mmrbc = (pcix_cmd & PCIX_COMMAND_MMRBC_MASK) >> + PCIX_COMMAND_MMRBC_SHIFT; + stat_mmrbc = (pcix_stat_hi_word & PCIX_STATUS_HI_MMRBC_MASK) >> + PCIX_STATUS_HI_MMRBC_SHIFT; + if (stat_mmrbc == PCIX_STATUS_HI_MMRBC_4K) + stat_mmrbc = PCIX_STATUS_HI_MMRBC_2K; + if (cmd_mmrbc > stat_mmrbc) { + pcix_cmd &= ~PCIX_COMMAND_MMRBC_MASK; + pcix_cmd |= stat_mmrbc << PCIX_COMMAND_MMRBC_SHIFT; + e1000_write_pci_cfg(hw, PCIX_COMMAND_REGISTER, &pcix_cmd); + } +} + +/** + * e1000_clear_hw_cntrs_base_generic - Clear base hardware counters + * @hw: pointer to the HW structure + * + * Clears the base hardware counters by reading the counter registers. + **/ +void e1000_clear_hw_cntrs_base_generic(struct e1000_hw *hw) +{ + DEBUGFUNC("e1000_clear_hw_cntrs_base_generic"); + + E1000_READ_REG(hw, E1000_CRCERRS); + E1000_READ_REG(hw, E1000_SYMERRS); + E1000_READ_REG(hw, E1000_MPC); + E1000_READ_REG(hw, E1000_SCC); + E1000_READ_REG(hw, E1000_ECOL); + E1000_READ_REG(hw, E1000_MCC); + E1000_READ_REG(hw, E1000_LATECOL); + E1000_READ_REG(hw, E1000_COLC); + E1000_READ_REG(hw, E1000_DC); + E1000_READ_REG(hw, E1000_SEC); + E1000_READ_REG(hw, E1000_RLEC); + E1000_READ_REG(hw, E1000_XONRXC); + E1000_READ_REG(hw, E1000_XONTXC); + E1000_READ_REG(hw, E1000_XOFFRXC); + E1000_READ_REG(hw, E1000_XOFFTXC); + E1000_READ_REG(hw, E1000_FCRUC); + E1000_READ_REG(hw, E1000_GPRC); + E1000_READ_REG(hw, E1000_BPRC); + E1000_READ_REG(hw, E1000_MPRC); + E1000_READ_REG(hw, E1000_GPTC); + E1000_READ_REG(hw, E1000_GORCL); + E1000_READ_REG(hw, E1000_GORCH); + E1000_READ_REG(hw, E1000_GOTCL); + E1000_READ_REG(hw, E1000_GOTCH); + E1000_READ_REG(hw, E1000_RNBC); + E1000_READ_REG(hw, E1000_RUC); + E1000_READ_REG(hw, E1000_RFC); + E1000_READ_REG(hw, E1000_ROC); + E1000_READ_REG(hw, E1000_RJC); + E1000_READ_REG(hw, E1000_TORL); + E1000_READ_REG(hw, E1000_TORH); + E1000_READ_REG(hw, E1000_TOTL); + E1000_READ_REG(hw, E1000_TOTH); + E1000_READ_REG(hw, E1000_TPR); + E1000_READ_REG(hw, E1000_TPT); + E1000_READ_REG(hw, E1000_MPTC); + E1000_READ_REG(hw, E1000_BPTC); +} + +/** + * e1000_check_for_copper_link_generic - Check for link (Copper) + * @hw: pointer to the HW structure + * + * Checks to see of the link status of the hardware has changed. If a + * change in link status has been detected, then we read the PHY registers + * to get the current speed/duplex if link exists. + **/ +s32 e1000_check_for_copper_link_generic(struct e1000_hw *hw) +{ + struct e1000_mac_info *mac = &hw->mac; + s32 ret_val; + bool link; + + DEBUGFUNC("e1000_check_for_copper_link"); + + /* + * We only want to go out to the PHY registers to see if Auto-Neg + * has completed and/or if our link status has changed. The + * get_link_status flag is set upon receiving a Link Status + * Change or Rx Sequence Error interrupt. + */ + if (!mac->get_link_status) { + ret_val = E1000_SUCCESS; + goto out; + } + + /* + * First we want to see if the MII Status Register reports + * link. If so, then we want to get the current speed/duplex + * of the PHY. + */ + ret_val = e1000_phy_has_link_generic(hw, 1, 0, &link); + if (ret_val) + goto out; + + if (!link) + goto out; /* No link detected */ + + mac->get_link_status = FALSE; + + /* + * Check if there was DownShift, must be checked + * immediately after link-up + */ + e1000_check_downshift_generic(hw); + + /* + * If we are forcing speed/duplex, then we simply return since + * we have already determined whether we have link or not. + */ + if (!mac->autoneg) { + ret_val = -E1000_ERR_CONFIG; + goto out; + } + + /* + * Auto-Neg is enabled. Auto Speed Detection takes care + * of MAC speed/duplex configuration. So we only need to + * configure Collision Distance in the MAC. + */ + e1000_config_collision_dist_generic(hw); + + /* + * Configure Flow Control now that Auto-Neg has completed. + * First, we need to restore the desired flow control + * settings because we may have had to re-autoneg with a + * different link partner. + */ + ret_val = e1000_config_fc_after_link_up_generic(hw); + if (ret_val) + DEBUGOUT("Error configuring flow control\n"); + +out: + return ret_val; +} + +/** + * e1000_check_for_fiber_link_generic - Check for link (Fiber) + * @hw: pointer to the HW structure + * + * Checks for link up on the hardware. If link is not up and we have + * a signal, then we need to force link up. + **/ +s32 e1000_check_for_fiber_link_generic(struct e1000_hw *hw) +{ + struct e1000_mac_info *mac = &hw->mac; + u32 rxcw; + u32 ctrl; + u32 status; + s32 ret_val = E1000_SUCCESS; + + DEBUGFUNC("e1000_check_for_fiber_link_generic"); + + ctrl = E1000_READ_REG(hw, E1000_CTRL); + status = E1000_READ_REG(hw, E1000_STATUS); + rxcw = E1000_READ_REG(hw, E1000_RXCW); + + /* + * If we don't have link (auto-negotiation failed or link partner + * cannot auto-negotiate), the cable is plugged in (we have signal), + * and our link partner is not trying to auto-negotiate with us (we + * are receiving idles or data), we need to force link up. We also + * need to give auto-negotiation time to complete, in case the cable + * was just plugged in. The autoneg_failed flag does this. + */ + /* (ctrl & E1000_CTRL_SWDPIN1) == 1 == have signal */ + if ((ctrl & E1000_CTRL_SWDPIN1) && (!(status & E1000_STATUS_LU)) && + (!(rxcw & E1000_RXCW_C))) { + if (mac->autoneg_failed == 0) { + mac->autoneg_failed = 1; + goto out; + } + DEBUGOUT("NOT RXing /C/, disable AutoNeg and force link.\n"); + + /* Disable auto-negotiation in the TXCW register */ + E1000_WRITE_REG(hw, E1000_TXCW, (mac->txcw & ~E1000_TXCW_ANE)); + + /* Force link-up and also force full-duplex. */ + ctrl = E1000_READ_REG(hw, E1000_CTRL); + ctrl |= (E1000_CTRL_SLU | E1000_CTRL_FD); + E1000_WRITE_REG(hw, E1000_CTRL, ctrl); + + /* Configure Flow Control after forcing link up. */ + ret_val = e1000_config_fc_after_link_up_generic(hw); + if (ret_val) { + DEBUGOUT("Error configuring flow control\n"); + goto out; + } + } else if ((ctrl & E1000_CTRL_SLU) && (rxcw & E1000_RXCW_C)) { + /* + * If we are forcing link and we are receiving /C/ ordered + * sets, re-enable auto-negotiation in the TXCW register + * and disable forced link in the Device Control register + * in an attempt to auto-negotiate with our link partner. + */ + DEBUGOUT("RXing /C/, enable AutoNeg and stop forcing link.\n"); + E1000_WRITE_REG(hw, E1000_TXCW, mac->txcw); + E1000_WRITE_REG(hw, E1000_CTRL, (ctrl & ~E1000_CTRL_SLU)); + + mac->serdes_has_link = TRUE; + } + +out: + return ret_val; +} + +/** + * e1000_check_for_serdes_link_generic - Check for link (Serdes) + * @hw: pointer to the HW structure + * + * Checks for link up on the hardware. If link is not up and we have + * a signal, then we need to force link up. + **/ +s32 e1000_check_for_serdes_link_generic(struct e1000_hw *hw) +{ + struct e1000_mac_info *mac = &hw->mac; + u32 rxcw; + u32 ctrl; + u32 status; + s32 ret_val = E1000_SUCCESS; + + DEBUGFUNC("e1000_check_for_serdes_link_generic"); + + ctrl = E1000_READ_REG(hw, E1000_CTRL); + status = E1000_READ_REG(hw, E1000_STATUS); + rxcw = E1000_READ_REG(hw, E1000_RXCW); + + /* + * If we don't have link (auto-negotiation failed or link partner + * cannot auto-negotiate), and our link partner is not trying to + * auto-negotiate with us (we are receiving idles or data), + * we need to force link up. We also need to give auto-negotiation + * time to complete. + */ + /* (ctrl & E1000_CTRL_SWDPIN1) == 1 == have signal */ + if ((!(status & E1000_STATUS_LU)) && (!(rxcw & E1000_RXCW_C))) { + if (mac->autoneg_failed == 0) { + mac->autoneg_failed = 1; + goto out; + } + DEBUGOUT("NOT RXing /C/, disable AutoNeg and force link.\n"); + + /* Disable auto-negotiation in the TXCW register */ + E1000_WRITE_REG(hw, E1000_TXCW, (mac->txcw & ~E1000_TXCW_ANE)); + + /* Force link-up and also force full-duplex. */ + ctrl = E1000_READ_REG(hw, E1000_CTRL); + ctrl |= (E1000_CTRL_SLU | E1000_CTRL_FD); + E1000_WRITE_REG(hw, E1000_CTRL, ctrl); + + /* Configure Flow Control after forcing link up. */ + ret_val = e1000_config_fc_after_link_up_generic(hw); + if (ret_val) { + DEBUGOUT("Error configuring flow control\n"); + goto out; + } + } else if ((ctrl & E1000_CTRL_SLU) && (rxcw & E1000_RXCW_C)) { + /* + * If we are forcing link and we are receiving /C/ ordered + * sets, re-enable auto-negotiation in the TXCW register + * and disable forced link in the Device Control register + * in an attempt to auto-negotiate with our link partner. + */ + DEBUGOUT("RXing /C/, enable AutoNeg and stop forcing link.\n"); + E1000_WRITE_REG(hw, E1000_TXCW, mac->txcw); + E1000_WRITE_REG(hw, E1000_CTRL, (ctrl & ~E1000_CTRL_SLU)); + + mac->serdes_has_link = TRUE; + } else if (!(E1000_TXCW_ANE & E1000_READ_REG(hw, E1000_TXCW))) { + /* + * If we force link for non-auto-negotiation switch, check + * link status based on MAC synchronization for internal + * serdes media type. + */ + /* SYNCH bit and IV bit are sticky. */ + usec_delay(10); + rxcw = E1000_READ_REG(hw, E1000_RXCW); + if (rxcw & E1000_RXCW_SYNCH) { + if (!(rxcw & E1000_RXCW_IV)) { + mac->serdes_has_link = TRUE; + DEBUGOUT("SERDES: Link up - forced.\n"); + } + } else { + mac->serdes_has_link = FALSE; + DEBUGOUT("SERDES: Link down - force failed.\n"); + } + } + + if (E1000_TXCW_ANE & E1000_READ_REG(hw, E1000_TXCW)) { + status = E1000_READ_REG(hw, E1000_STATUS); + if (status & E1000_STATUS_LU) { + /* SYNCH bit and IV bit are sticky, so reread rxcw. */ + usec_delay(10); + rxcw = E1000_READ_REG(hw, E1000_RXCW); + if (rxcw & E1000_RXCW_SYNCH) { + if (!(rxcw & E1000_RXCW_IV)) { + mac->serdes_has_link = TRUE; + DEBUGOUT("SERDES: Link up - autoneg " + "completed sucessfully.\n"); + } else { + mac->serdes_has_link = FALSE; + DEBUGOUT("SERDES: Link down - invalid" + "codewords detected in autoneg.\n"); + } + } else { + mac->serdes_has_link = FALSE; + DEBUGOUT("SERDES: Link down - no sync.\n"); + } + } else { + mac->serdes_has_link = FALSE; + DEBUGOUT("SERDES: Link down - autoneg failed\n"); + } + } + +out: + return ret_val; +} + +/** + * e1000_setup_link_generic - Setup flow control and link settings + * @hw: pointer to the HW structure + * + * Determines which flow control settings to use, then configures flow + * control. Calls the appropriate media-specific link configuration + * function. Assuming the adapter has a valid link partner, a valid link + * should be established. Assumes the hardware has previously been reset + * and the transmitter and receiver are not enabled. + **/ +s32 e1000_setup_link_generic(struct e1000_hw *hw) +{ + s32 ret_val = E1000_SUCCESS; + + DEBUGFUNC("e1000_setup_link_generic"); + + /* + * In the case of the phy reset being blocked, we already have a link. + * We do not need to set it up again. + */ + if (hw->phy.ops.check_reset_block) + if (hw->phy.ops.check_reset_block(hw)) + goto out; + + /* + * If requested flow control is set to default, set flow control + * based on the EEPROM flow control settings. + */ + if (hw->fc.requested_mode == e1000_fc_default) { + ret_val = e1000_set_default_fc_generic(hw); + if (ret_val) + goto out; + } + + /* + * Save off the requested flow control mode for use later. Depending + * on the link partner's capabilities, we may or may not use this mode. + */ + hw->fc.current_mode = hw->fc.requested_mode; + + DEBUGOUT1("After fix-ups FlowControl is now = %x\n", + hw->fc.current_mode); + + /* Call the necessary media_type subroutine to configure the link. */ + ret_val = hw->mac.ops.setup_physical_interface(hw); + if (ret_val) + goto out; + + /* + * Initialize the flow control address, type, and PAUSE timer + * registers to their default values. This is done even if flow + * control is disabled, because it does not hurt anything to + * initialize these registers. + */ + DEBUGOUT("Initializing the Flow Control address, type and timer regs\n"); + E1000_WRITE_REG(hw, E1000_FCT, FLOW_CONTROL_TYPE); + E1000_WRITE_REG(hw, E1000_FCAH, FLOW_CONTROL_ADDRESS_HIGH); + E1000_WRITE_REG(hw, E1000_FCAL, FLOW_CONTROL_ADDRESS_LOW); + + E1000_WRITE_REG(hw, E1000_FCTTV, hw->fc.pause_time); + + ret_val = e1000_set_fc_watermarks_generic(hw); + +out: + return ret_val; +} + +/** + * e1000_setup_fiber_serdes_link_generic - Setup link for fiber/serdes + * @hw: pointer to the HW structure + * + * Configures collision distance and flow control for fiber and serdes + * links. Upon successful setup, poll for link. + **/ +s32 e1000_setup_fiber_serdes_link_generic(struct e1000_hw *hw) +{ + u32 ctrl; + s32 ret_val = E1000_SUCCESS; + + DEBUGFUNC("e1000_setup_fiber_serdes_link_generic"); + + ctrl = E1000_READ_REG(hw, E1000_CTRL); + + /* Take the link out of reset */ + ctrl &= ~E1000_CTRL_LRST; + + e1000_config_collision_dist_generic(hw); + + ret_val = e1000_commit_fc_settings_generic(hw); + if (ret_val) + goto out; + + /* + * Since auto-negotiation is enabled, take the link out of reset (the + * link will be in reset, because we previously reset the chip). This + * will restart auto-negotiation. If auto-negotiation is successful + * then the link-up status bit will be set and the flow control enable + * bits (RFCE and TFCE) will be set according to their negotiated value. + */ + DEBUGOUT("Auto-negotiation enabled\n"); + + E1000_WRITE_REG(hw, E1000_CTRL, ctrl); + E1000_WRITE_FLUSH(hw); + msec_delay(1); + + /* + * For these adapters, the SW definable pin 1 is set when the optics + * detect a signal. If we have a signal, then poll for a "Link-Up" + * indication. + */ + if (hw->phy.media_type == e1000_media_type_internal_serdes || + (E1000_READ_REG(hw, E1000_CTRL) & E1000_CTRL_SWDPIN1)) { + ret_val = e1000_poll_fiber_serdes_link_generic(hw); + } else { + DEBUGOUT("No signal detected\n"); + } + +out: + return ret_val; +} + +/** + * e1000_config_collision_dist_generic - Configure collision distance + * @hw: pointer to the HW structure + * + * Configures the collision distance to the default value and is used + * during link setup. Currently no func pointer exists and all + * implementations are handled in the generic version of this function. + **/ +void e1000_config_collision_dist_generic(struct e1000_hw *hw) +{ + u32 tctl; + + DEBUGFUNC("e1000_config_collision_dist_generic"); + + tctl = E1000_READ_REG(hw, E1000_TCTL); + + tctl &= ~E1000_TCTL_COLD; + tctl |= E1000_COLLISION_DISTANCE << E1000_COLD_SHIFT; + + E1000_WRITE_REG(hw, E1000_TCTL, tctl); + E1000_WRITE_FLUSH(hw); +} + +/** + * e1000_poll_fiber_serdes_link_generic - Poll for link up + * @hw: pointer to the HW structure + * + * Polls for link up by reading the status register, if link fails to come + * up with auto-negotiation, then the link is forced if a signal is detected. + **/ +s32 e1000_poll_fiber_serdes_link_generic(struct e1000_hw *hw) +{ + struct e1000_mac_info *mac = &hw->mac; + u32 i, status; + s32 ret_val = E1000_SUCCESS; + + DEBUGFUNC("e1000_poll_fiber_serdes_link_generic"); + + /* + * If we have a signal (the cable is plugged in, or assumed TRUE for + * serdes media) then poll for a "Link-Up" indication in the Device + * Status Register. Time-out if a link isn't seen in 500 milliseconds + * seconds (Auto-negotiation should complete in less than 500 + * milliseconds even if the other end is doing it in SW). + */ + for (i = 0; i < FIBER_LINK_UP_LIMIT; i++) { + msec_delay(10); + status = E1000_READ_REG(hw, E1000_STATUS); + if (status & E1000_STATUS_LU) + break; + } + if (i == FIBER_LINK_UP_LIMIT) { + DEBUGOUT("Never got a valid link from auto-neg!!!\n"); + mac->autoneg_failed = 1; + /* + * AutoNeg failed to achieve a link, so we'll call + * mac->check_for_link. This routine will force the + * link up if we detect a signal. This will allow us to + * communicate with non-autonegotiating link partners. + */ + ret_val = hw->mac.ops.check_for_link(hw); + if (ret_val) { + DEBUGOUT("Error while checking for link\n"); + goto out; + } + mac->autoneg_failed = 0; + } else { + mac->autoneg_failed = 0; + DEBUGOUT("Valid Link Found\n"); + } + +out: + return ret_val; +} + +/** + * e1000_commit_fc_settings_generic - Configure flow control + * @hw: pointer to the HW structure + * + * Write the flow control settings to the Transmit Config Word Register (TXCW) + * base on the flow control settings in e1000_mac_info. + **/ +s32 e1000_commit_fc_settings_generic(struct e1000_hw *hw) +{ + struct e1000_mac_info *mac = &hw->mac; + u32 txcw; + s32 ret_val = E1000_SUCCESS; + + DEBUGFUNC("e1000_commit_fc_settings_generic"); + + /* + * Check for a software override of the flow control settings, and + * setup the device accordingly. If auto-negotiation is enabled, then + * software will have to set the "PAUSE" bits to the correct value in + * the Transmit Config Word Register (TXCW) and re-start auto- + * negotiation. However, if auto-negotiation is disabled, then + * software will have to manually configure the two flow control enable + * bits in the CTRL register. + * + * The possible values of the "fc" parameter are: + * 0: Flow control is completely disabled + * 1: Rx flow control is enabled (we can receive pause frames, + * but not send pause frames). + * 2: Tx flow control is enabled (we can send pause frames but we + * do not support receiving pause frames). + * 3: Both Rx and Tx flow control (symmetric) are enabled. + */ + switch (hw->fc.current_mode) { + case e1000_fc_none: + /* Flow control completely disabled by a software over-ride. */ + txcw = (E1000_TXCW_ANE | E1000_TXCW_FD); + break; + case e1000_fc_rx_pause: + /* + * Rx Flow control is enabled and Tx Flow control is disabled + * by a software over-ride. Since there really isn't a way to + * advertise that we are capable of Rx Pause ONLY, we will + * advertise that we support both symmetric and asymmetric RX + * PAUSE. Later, we will disable the adapter's ability to send + * PAUSE frames. + */ + txcw = (E1000_TXCW_ANE | E1000_TXCW_FD | E1000_TXCW_PAUSE_MASK); + break; + case e1000_fc_tx_pause: + /* + * Tx Flow control is enabled, and Rx Flow control is disabled, + * by a software over-ride. + */ + txcw = (E1000_TXCW_ANE | E1000_TXCW_FD | E1000_TXCW_ASM_DIR); + break; + case e1000_fc_full: + /* + * Flow control (both Rx and Tx) is enabled by a software + * over-ride. + */ + txcw = (E1000_TXCW_ANE | E1000_TXCW_FD | E1000_TXCW_PAUSE_MASK); + break; + default: + DEBUGOUT("Flow control param set incorrectly\n"); + ret_val = -E1000_ERR_CONFIG; + goto out; + break; + } + + E1000_WRITE_REG(hw, E1000_TXCW, txcw); + mac->txcw = txcw; + +out: + return ret_val; +} + +/** + * e1000_set_fc_watermarks_generic - Set flow control high/low watermarks + * @hw: pointer to the HW structure + * + * Sets the flow control high/low threshold (watermark) registers. If + * flow control XON frame transmission is enabled, then set XON frame + * transmission as well. + **/ +s32 e1000_set_fc_watermarks_generic(struct e1000_hw *hw) +{ + s32 ret_val = E1000_SUCCESS; + u32 fcrtl = 0, fcrth = 0; + + DEBUGFUNC("e1000_set_fc_watermarks_generic"); + + /* + * Set the flow control receive threshold registers. Normally, + * these registers will be set to a default threshold that may be + * adjusted later by the driver's runtime code. However, if the + * ability to transmit pause frames is not enabled, then these + * registers will be set to 0. + */ + if (hw->fc.current_mode & e1000_fc_tx_pause) { + /* + * We need to set up the Receive Threshold high and low water + * marks as well as (optionally) enabling the transmission of + * XON frames. + */ + fcrtl = hw->fc.low_water; + if (hw->fc.send_xon) + fcrtl |= E1000_FCRTL_XONE; + + fcrth = hw->fc.high_water; + } + E1000_WRITE_REG(hw, E1000_FCRTL, fcrtl); + E1000_WRITE_REG(hw, E1000_FCRTH, fcrth); + + return ret_val; +} + +/** + * e1000_set_default_fc_generic - Set flow control default values + * @hw: pointer to the HW structure + * + * Read the EEPROM for the default values for flow control and store the + * values. + **/ +s32 e1000_set_default_fc_generic(struct e1000_hw *hw) +{ + s32 ret_val = E1000_SUCCESS; + u16 nvm_data; + + DEBUGFUNC("e1000_set_default_fc_generic"); + + /* + * Read and store word 0x0F of the EEPROM. This word contains bits + * that determine the hardware's default PAUSE (flow control) mode, + * a bit that determines whether the HW defaults to enabling or + * disabling auto-negotiation, and the direction of the + * SW defined pins. If there is no SW over-ride of the flow + * control setting, then the variable hw->fc will + * be initialized based on a value in the EEPROM. + */ + ret_val = hw->nvm.ops.read(hw, NVM_INIT_CONTROL2_REG, 1, &nvm_data); + + if (ret_val) { + DEBUGOUT("NVM Read Error\n"); + goto out; + } + + if ((nvm_data & NVM_WORD0F_PAUSE_MASK) == 0) + hw->fc.requested_mode = e1000_fc_none; + else if ((nvm_data & NVM_WORD0F_PAUSE_MASK) == + NVM_WORD0F_ASM_DIR) + hw->fc.requested_mode = e1000_fc_tx_pause; + else + hw->fc.requested_mode = e1000_fc_full; + +out: + return ret_val; +} + +/** + * e1000_force_mac_fc_generic - Force the MAC's flow control settings + * @hw: pointer to the HW structure + * + * Force the MAC's flow control settings. Sets the TFCE and RFCE bits in the + * device control register to reflect the adapter settings. TFCE and RFCE + * need to be explicitly set by software when a copper PHY is used because + * autonegotiation is managed by the PHY rather than the MAC. Software must + * also configure these bits when link is forced on a fiber connection. + **/ +s32 e1000_force_mac_fc_generic(struct e1000_hw *hw) +{ + u32 ctrl; + s32 ret_val = E1000_SUCCESS; + + DEBUGFUNC("e1000_force_mac_fc_generic"); + + ctrl = E1000_READ_REG(hw, E1000_CTRL); + + /* + * Because we didn't get link via the internal auto-negotiation + * mechanism (we either forced link or we got link via PHY + * auto-neg), we have to manually enable/disable transmit an + * receive flow control. + * + * The "Case" statement below enables/disable flow control + * according to the "hw->fc.current_mode" parameter. + * + * The possible values of the "fc" parameter are: + * 0: Flow control is completely disabled + * 1: Rx flow control is enabled (we can receive pause + * frames but not send pause frames). + * 2: Tx flow control is enabled (we can send pause frames + * frames but we do not receive pause frames). + * 3: Both Rx and Tx flow control (symmetric) is enabled. + * other: No other values should be possible at this point. + */ + DEBUGOUT1("hw->fc.current_mode = %u\n", hw->fc.current_mode); + + switch (hw->fc.current_mode) { + case e1000_fc_none: + ctrl &= (~(E1000_CTRL_TFCE | E1000_CTRL_RFCE)); + break; + case e1000_fc_rx_pause: + ctrl &= (~E1000_CTRL_TFCE); + ctrl |= E1000_CTRL_RFCE; + break; + case e1000_fc_tx_pause: + ctrl &= (~E1000_CTRL_RFCE); + ctrl |= E1000_CTRL_TFCE; + break; + case e1000_fc_full: + ctrl |= (E1000_CTRL_TFCE | E1000_CTRL_RFCE); + break; + default: + DEBUGOUT("Flow control param set incorrectly\n"); + ret_val = -E1000_ERR_CONFIG; + goto out; + } + + E1000_WRITE_REG(hw, E1000_CTRL, ctrl); + +out: + return ret_val; +} + +/** + * e1000_config_fc_after_link_up_generic - Configures flow control after link + * @hw: pointer to the HW structure + * + * Checks the status of auto-negotiation after link up to ensure that the + * speed and duplex were not forced. If the link needed to be forced, then + * flow control needs to be forced also. If auto-negotiation is enabled + * and did not fail, then we configure flow control based on our link + * partner. + **/ +s32 e1000_config_fc_after_link_up_generic(struct e1000_hw *hw) +{ + struct e1000_mac_info *mac = &hw->mac; + s32 ret_val = E1000_SUCCESS; + u16 mii_status_reg, mii_nway_adv_reg, mii_nway_lp_ability_reg; + u16 speed, duplex; + + DEBUGFUNC("e1000_config_fc_after_link_up_generic"); + + /* + * Check for the case where we have fiber media and auto-neg failed + * so we had to force link. In this case, we need to force the + * configuration of the MAC to match the "fc" parameter. + */ + if (mac->autoneg_failed) { + if (hw->phy.media_type == e1000_media_type_fiber || + hw->phy.media_type == e1000_media_type_internal_serdes) + ret_val = e1000_force_mac_fc_generic(hw); + } else { + if (hw->phy.media_type == e1000_media_type_copper) + ret_val = e1000_force_mac_fc_generic(hw); + } + + if (ret_val) { + DEBUGOUT("Error forcing flow control settings\n"); + goto out; + } + + /* + * Check for the case where we have copper media and auto-neg is + * enabled. In this case, we need to check and see if Auto-Neg + * has completed, and if so, how the PHY and link partner has + * flow control configured. + */ + if ((hw->phy.media_type == e1000_media_type_copper) && mac->autoneg) { + /* + * Read the MII Status Register and check to see if AutoNeg + * has completed. We read this twice because this reg has + * some "sticky" (latched) bits. + */ + ret_val = hw->phy.ops.read_reg(hw, PHY_STATUS, &mii_status_reg); + if (ret_val) + goto out; + ret_val = hw->phy.ops.read_reg(hw, PHY_STATUS, &mii_status_reg); + if (ret_val) + goto out; + + if (!(mii_status_reg & MII_SR_AUTONEG_COMPLETE)) { + DEBUGOUT("Copper PHY and Auto Neg " + "has not completed.\n"); + goto out; + } + + /* + * The AutoNeg process has completed, so we now need to + * read both the Auto Negotiation Advertisement + * Register (Address 4) and the Auto_Negotiation Base + * Page Ability Register (Address 5) to determine how + * flow control was negotiated. + */ + ret_val = hw->phy.ops.read_reg(hw, PHY_AUTONEG_ADV, + &mii_nway_adv_reg); + if (ret_val) + goto out; + ret_val = hw->phy.ops.read_reg(hw, PHY_LP_ABILITY, + &mii_nway_lp_ability_reg); + if (ret_val) + goto out; + + /* + * Two bits in the Auto Negotiation Advertisement Register + * (Address 4) and two bits in the Auto Negotiation Base + * Page Ability Register (Address 5) determine flow control + * for both the PHY and the link partner. The following + * table, taken out of the IEEE 802.3ab/D6.0 dated March 25, + * 1999, describes these PAUSE resolution bits and how flow + * control is determined based upon these settings. + * NOTE: DC = Don't Care + * + * LOCAL DEVICE | LINK PARTNER + * PAUSE | ASM_DIR | PAUSE | ASM_DIR | NIC Resolution + *-------|---------|-------|---------|-------------------- + * 0 | 0 | DC | DC | e1000_fc_none + * 0 | 1 | 0 | DC | e1000_fc_none + * 0 | 1 | 1 | 0 | e1000_fc_none + * 0 | 1 | 1 | 1 | e1000_fc_tx_pause + * 1 | 0 | 0 | DC | e1000_fc_none + * 1 | DC | 1 | DC | e1000_fc_full + * 1 | 1 | 0 | 0 | e1000_fc_none + * 1 | 1 | 0 | 1 | e1000_fc_rx_pause + * + * Are both PAUSE bits set to 1? If so, this implies + * Symmetric Flow Control is enabled at both ends. The + * ASM_DIR bits are irrelevant per the spec. + * + * For Symmetric Flow Control: + * + * LOCAL DEVICE | LINK PARTNER + * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result + *-------|---------|-------|---------|-------------------- + * 1 | DC | 1 | DC | E1000_fc_full + * + */ + if ((mii_nway_adv_reg & NWAY_AR_PAUSE) && + (mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE)) { + /* + * Now we need to check if the user selected Rx ONLY + * of pause frames. In this case, we had to advertise + * FULL flow control because we could not advertise RX + * ONLY. Hence, we must now check to see if we need to + * turn OFF the TRANSMISSION of PAUSE frames. + */ + if (hw->fc.requested_mode == e1000_fc_full) { + hw->fc.current_mode = e1000_fc_full; + DEBUGOUT("Flow Control = FULL.\r\n"); + } else { + hw->fc.current_mode = e1000_fc_rx_pause; + DEBUGOUT("Flow Control = " + "RX PAUSE frames only.\r\n"); + } + } + /* + * For receiving PAUSE frames ONLY. + * + * LOCAL DEVICE | LINK PARTNER + * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result + *-------|---------|-------|---------|-------------------- + * 0 | 1 | 1 | 1 | e1000_fc_tx_pause + */ + else if (!(mii_nway_adv_reg & NWAY_AR_PAUSE) && + (mii_nway_adv_reg & NWAY_AR_ASM_DIR) && + (mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) && + (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR)) { + hw->fc.current_mode = e1000_fc_tx_pause; + DEBUGOUT("Flow Control = TX PAUSE frames only.\r\n"); + } + /* + * For transmitting PAUSE frames ONLY. + * + * LOCAL DEVICE | LINK PARTNER + * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result + *-------|---------|-------|---------|-------------------- + * 1 | 1 | 0 | 1 | e1000_fc_rx_pause + */ + else if ((mii_nway_adv_reg & NWAY_AR_PAUSE) && + (mii_nway_adv_reg & NWAY_AR_ASM_DIR) && + !(mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) && + (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR)) { + hw->fc.current_mode = e1000_fc_rx_pause; + DEBUGOUT("Flow Control = RX PAUSE frames only.\r\n"); + } else { + /* + * Per the IEEE spec, at this point flow control + * should be disabled. + */ + hw->fc.current_mode = e1000_fc_none; + DEBUGOUT("Flow Control = NONE.\r\n"); + } + + /* + * Now we need to do one last check... If we auto- + * negotiated to HALF DUPLEX, flow control should not be + * enabled per IEEE 802.3 spec. + */ + ret_val = mac->ops.get_link_up_info(hw, &speed, &duplex); + if (ret_val) { + DEBUGOUT("Error getting link speed and duplex\n"); + goto out; + } + + if (duplex == HALF_DUPLEX) + hw->fc.current_mode = e1000_fc_none; + + /* + * Now we call a subroutine to actually force the MAC + * controller to use the correct flow control settings. + */ + ret_val = e1000_force_mac_fc_generic(hw); + if (ret_val) { + DEBUGOUT("Error forcing flow control settings\n"); + goto out; + } + } + +out: + return ret_val; +} + +/** + * e1000_get_speed_and_duplex_copper_generic - Retrieve current speed/duplex + * @hw: pointer to the HW structure + * @speed: stores the current speed + * @duplex: stores the current duplex + * + * Read the status register for the current speed/duplex and store the current + * speed and duplex for copper connections. + **/ +s32 e1000_get_speed_and_duplex_copper_generic(struct e1000_hw *hw, u16 *speed, + u16 *duplex) +{ + u32 status; + + DEBUGFUNC("e1000_get_speed_and_duplex_copper_generic"); + + status = E1000_READ_REG(hw, E1000_STATUS); + if (status & E1000_STATUS_SPEED_1000) { + *speed = SPEED_1000; + DEBUGOUT("1000 Mbs, "); + } else if (status & E1000_STATUS_SPEED_100) { + *speed = SPEED_100; + DEBUGOUT("100 Mbs, "); + } else { + *speed = SPEED_10; + DEBUGOUT("10 Mbs, "); + } + + if (status & E1000_STATUS_FD) { + *duplex = FULL_DUPLEX; + DEBUGOUT("Full Duplex\n"); + } else { + *duplex = HALF_DUPLEX; + DEBUGOUT("Half Duplex\n"); + } + + return E1000_SUCCESS; +} + +/** + * e1000_get_speed_and_duplex_fiber_generic - Retrieve current speed/duplex + * @hw: pointer to the HW structure + * @speed: stores the current speed + * @duplex: stores the current duplex + * + * Sets the speed and duplex to gigabit full duplex (the only possible option) + * for fiber/serdes links. + **/ +s32 e1000_get_speed_and_duplex_fiber_serdes_generic(struct e1000_hw *hw, + u16 *speed, u16 *duplex) +{ + DEBUGFUNC("e1000_get_speed_and_duplex_fiber_serdes_generic"); + + *speed = SPEED_1000; + *duplex = FULL_DUPLEX; + + return E1000_SUCCESS; +} + +/** + * e1000_get_hw_semaphore_generic - Acquire hardware semaphore + * @hw: pointer to the HW structure + * + * Acquire the HW semaphore to access the PHY or NVM + **/ +s32 e1000_get_hw_semaphore_generic(struct e1000_hw *hw) +{ + u32 swsm; + s32 ret_val = E1000_SUCCESS; + s32 timeout = hw->nvm.word_size + 1; + s32 i = 0; + + DEBUGFUNC("e1000_get_hw_semaphore_generic"); + + /* Get the SW semaphore */ + while (i < timeout) { + swsm = E1000_READ_REG(hw, E1000_SWSM); + if (!(swsm & E1000_SWSM_SMBI)) + break; + + usec_delay(50); + i++; + } + + if (i == timeout) { + DEBUGOUT("Driver can't access device - SMBI bit is set.\n"); + ret_val = -E1000_ERR_NVM; + goto out; + } + + /* Get the FW semaphore. */ + for (i = 0; i < timeout; i++) { + swsm = E1000_READ_REG(hw, E1000_SWSM); + E1000_WRITE_REG(hw, E1000_SWSM, swsm | E1000_SWSM_SWESMBI); + + /* Semaphore acquired if bit latched */ + if (E1000_READ_REG(hw, E1000_SWSM) & E1000_SWSM_SWESMBI) + break; + + usec_delay(50); + } + + if (i == timeout) { + /* Release semaphores */ + e1000_put_hw_semaphore_generic(hw); + DEBUGOUT("Driver can't access the NVM\n"); + ret_val = -E1000_ERR_NVM; + goto out; + } + +out: + return ret_val; +} + +/** + * e1000_put_hw_semaphore_generic - Release hardware semaphore + * @hw: pointer to the HW structure + * + * Release hardware semaphore used to access the PHY or NVM + **/ +void e1000_put_hw_semaphore_generic(struct e1000_hw *hw) +{ + u32 swsm; + + DEBUGFUNC("e1000_put_hw_semaphore_generic"); + + swsm = E1000_READ_REG(hw, E1000_SWSM); + + swsm &= ~(E1000_SWSM_SMBI | E1000_SWSM_SWESMBI); + + E1000_WRITE_REG(hw, E1000_SWSM, swsm); +} + +/** + * e1000_get_auto_rd_done_generic - Check for auto read completion + * @hw: pointer to the HW structure + * + * Check EEPROM for Auto Read done bit. + **/ +s32 e1000_get_auto_rd_done_generic(struct e1000_hw *hw) +{ + s32 i = 0; + s32 ret_val = E1000_SUCCESS; + + DEBUGFUNC("e1000_get_auto_rd_done_generic"); + + while (i < AUTO_READ_DONE_TIMEOUT) { + if (E1000_READ_REG(hw, E1000_EECD) & E1000_EECD_AUTO_RD) + break; + msec_delay(1); + i++; + } + + if (i == AUTO_READ_DONE_TIMEOUT) { + DEBUGOUT("Auto read by HW from NVM has not completed.\n"); + ret_val = -E1000_ERR_RESET; + goto out; + } + +out: + return ret_val; +} + +/** + * e1000_valid_led_default_generic - Verify a valid default LED config + * @hw: pointer to the HW structure + * @data: pointer to the NVM (EEPROM) + * + * Read the EEPROM for the current default LED configuration. If the + * LED configuration is not valid, set to a valid LED configuration. + **/ +s32 e1000_valid_led_default_generic(struct e1000_hw *hw, u16 *data) +{ + s32 ret_val; + + DEBUGFUNC("e1000_valid_led_default_generic"); + + ret_val = hw->nvm.ops.read(hw, NVM_ID_LED_SETTINGS, 1, data); + if (ret_val) { + DEBUGOUT("NVM Read Error\n"); + goto out; + } + + if (*data == ID_LED_RESERVED_0000 || *data == ID_LED_RESERVED_FFFF) + *data = ID_LED_DEFAULT; + +out: + return ret_val; +} + +/** + * e1000_id_led_init_generic - + * @hw: pointer to the HW structure + * + **/ +s32 e1000_id_led_init_generic(struct e1000_hw *hw) +{ + struct e1000_mac_info *mac = &hw->mac; + s32 ret_val; + const u32 ledctl_mask = 0x000000FF; + const u32 ledctl_on = E1000_LEDCTL_MODE_LED_ON; + const u32 ledctl_off = E1000_LEDCTL_MODE_LED_OFF; + u16 data, i, temp; + const u16 led_mask = 0x0F; + + DEBUGFUNC("e1000_id_led_init_generic"); + + ret_val = hw->nvm.ops.valid_led_default(hw, &data); + if (ret_val) + goto out; + + mac->ledctl_default = E1000_READ_REG(hw, E1000_LEDCTL); + mac->ledctl_mode1 = mac->ledctl_default; + mac->ledctl_mode2 = mac->ledctl_default; + + for (i = 0; i < 4; i++) { + temp = (data >> (i << 2)) & led_mask; + switch (temp) { + case ID_LED_ON1_DEF2: + case ID_LED_ON1_ON2: + case ID_LED_ON1_OFF2: + mac->ledctl_mode1 &= ~(ledctl_mask << (i << 3)); + mac->ledctl_mode1 |= ledctl_on << (i << 3); + break; + case ID_LED_OFF1_DEF2: + case ID_LED_OFF1_ON2: + case ID_LED_OFF1_OFF2: + mac->ledctl_mode1 &= ~(ledctl_mask << (i << 3)); + mac->ledctl_mode1 |= ledctl_off << (i << 3); + break; + default: + /* Do nothing */ + break; + } + switch (temp) { + case ID_LED_DEF1_ON2: + case ID_LED_ON1_ON2: + case ID_LED_OFF1_ON2: + mac->ledctl_mode2 &= ~(ledctl_mask << (i << 3)); + mac->ledctl_mode2 |= ledctl_on << (i << 3); + break; + case ID_LED_DEF1_OFF2: + case ID_LED_ON1_OFF2: + case ID_LED_OFF1_OFF2: + mac->ledctl_mode2 &= ~(ledctl_mask << (i << 3)); + mac->ledctl_mode2 |= ledctl_off << (i << 3); + break; + default: + /* Do nothing */ + break; + } + } + +out: + return ret_val; +} + +/** + * e1000_setup_led_generic - Configures SW controllable LED + * @hw: pointer to the HW structure + * + * This prepares the SW controllable LED for use and saves the current state + * of the LED so it can be later restored. + **/ +s32 e1000_setup_led_generic(struct e1000_hw *hw) +{ + u32 ledctl; + s32 ret_val = E1000_SUCCESS; + + DEBUGFUNC("e1000_setup_led_generic"); + + if (hw->mac.ops.setup_led != e1000_setup_led_generic) { + ret_val = -E1000_ERR_CONFIG; + goto out; + } + + if (hw->phy.media_type == e1000_media_type_fiber) { + ledctl = E1000_READ_REG(hw, E1000_LEDCTL); + hw->mac.ledctl_default = ledctl; + /* Turn off LED0 */ + ledctl &= ~(E1000_LEDCTL_LED0_IVRT | + E1000_LEDCTL_LED0_BLINK | + E1000_LEDCTL_LED0_MODE_MASK); + ledctl |= (E1000_LEDCTL_MODE_LED_OFF << + E1000_LEDCTL_LED0_MODE_SHIFT); + E1000_WRITE_REG(hw, E1000_LEDCTL, ledctl); + } else if (hw->phy.media_type == e1000_media_type_copper) { + E1000_WRITE_REG(hw, E1000_LEDCTL, hw->mac.ledctl_mode1); + } + +out: + return ret_val; +} + +/** + * e1000_cleanup_led_generic - Set LED config to default operation + * @hw: pointer to the HW structure + * + * Remove the current LED configuration and set the LED configuration + * to the default value, saved from the EEPROM. + **/ +s32 e1000_cleanup_led_generic(struct e1000_hw *hw) +{ + s32 ret_val = E1000_SUCCESS; + + DEBUGFUNC("e1000_cleanup_led_generic"); + + if (hw->mac.ops.cleanup_led != e1000_cleanup_led_generic) { + ret_val = -E1000_ERR_CONFIG; + goto out; + } + + E1000_WRITE_REG(hw, E1000_LEDCTL, hw->mac.ledctl_default); + +out: + return ret_val; +} + +/** + * e1000_blink_led_generic - Blink LED + * @hw: pointer to the HW structure + * + * Blink the LEDs which are set to be on. + **/ +s32 e1000_blink_led_generic(struct e1000_hw *hw) +{ + u32 ledctl_blink = 0; + u32 i; + + DEBUGFUNC("e1000_blink_led_generic"); + + if (hw->phy.media_type == e1000_media_type_fiber) { + /* always blink LED0 for PCI-E fiber */ + ledctl_blink = E1000_LEDCTL_LED0_BLINK | + (E1000_LEDCTL_MODE_LED_ON << E1000_LEDCTL_LED0_MODE_SHIFT); + } else { + /* + * set the blink bit for each LED that's "on" (0x0E) + * in ledctl_mode2 + */ + ledctl_blink = hw->mac.ledctl_mode2; + for (i = 0; i < 4; i++) + if (((hw->mac.ledctl_mode2 >> (i * 8)) & 0xFF) == + E1000_LEDCTL_MODE_LED_ON) + ledctl_blink |= (E1000_LEDCTL_LED0_BLINK << + (i * 8)); + } + + E1000_WRITE_REG(hw, E1000_LEDCTL, ledctl_blink); + + return E1000_SUCCESS; +} + +/** + * e1000_led_on_generic - Turn LED on + * @hw: pointer to the HW structure + * + * Turn LED on. + **/ +s32 e1000_led_on_generic(struct e1000_hw *hw) +{ + u32 ctrl; + + DEBUGFUNC("e1000_led_on_generic"); + + switch (hw->phy.media_type) { + case e1000_media_type_fiber: + ctrl = E1000_READ_REG(hw, E1000_CTRL); + ctrl &= ~E1000_CTRL_SWDPIN0; + ctrl |= E1000_CTRL_SWDPIO0; + E1000_WRITE_REG(hw, E1000_CTRL, ctrl); + break; + case e1000_media_type_copper: + E1000_WRITE_REG(hw, E1000_LEDCTL, hw->mac.ledctl_mode2); + break; + default: + break; + } + + return E1000_SUCCESS; +} + +/** + * e1000_led_off_generic - Turn LED off + * @hw: pointer to the HW structure + * + * Turn LED off. + **/ +s32 e1000_led_off_generic(struct e1000_hw *hw) +{ + u32 ctrl; + + DEBUGFUNC("e1000_led_off_generic"); + + switch (hw->phy.media_type) { + case e1000_media_type_fiber: + ctrl = E1000_READ_REG(hw, E1000_CTRL); + ctrl |= E1000_CTRL_SWDPIN0; + ctrl |= E1000_CTRL_SWDPIO0; + E1000_WRITE_REG(hw, E1000_CTRL, ctrl); + break; + case e1000_media_type_copper: + E1000_WRITE_REG(hw, E1000_LEDCTL, hw->mac.ledctl_mode1); + break; + default: + break; + } + + return E1000_SUCCESS; +} + +/** + * e1000_set_pcie_no_snoop_generic - Set PCI-express capabilities + * @hw: pointer to the HW structure + * @no_snoop: bitmap of snoop events + * + * Set the PCI-express register to snoop for events enabled in 'no_snoop'. + **/ +void e1000_set_pcie_no_snoop_generic(struct e1000_hw *hw, u32 no_snoop) +{ + u32 gcr; + + DEBUGFUNC("e1000_set_pcie_no_snoop_generic"); + + if (hw->bus.type != e1000_bus_type_pci_express) + goto out; + + if (no_snoop) { + gcr = E1000_READ_REG(hw, E1000_GCR); + gcr &= ~(PCIE_NO_SNOOP_ALL); + gcr |= no_snoop; + E1000_WRITE_REG(hw, E1000_GCR, gcr); + } +out: + return; +} + +/** + * e1000_disable_pcie_master_generic - Disables PCI-express master access + * @hw: pointer to the HW structure + * + * Returns 0 (E1000_SUCCESS) if successful, else returns -10 + * (-E1000_ERR_MASTER_REQUESTS_PENDING) if master disable bit has not caused + * the master requests to be disabled. + * + * Disables PCI-Express master access and verifies there are no pending + * requests. + **/ +s32 e1000_disable_pcie_master_generic(struct e1000_hw *hw) +{ + u32 ctrl; + s32 timeout = MASTER_DISABLE_TIMEOUT; + s32 ret_val = E1000_SUCCESS; + + DEBUGFUNC("e1000_disable_pcie_master_generic"); + + if (hw->bus.type != e1000_bus_type_pci_express) + goto out; + + ctrl = E1000_READ_REG(hw, E1000_CTRL); + ctrl |= E1000_CTRL_GIO_MASTER_DISABLE; + E1000_WRITE_REG(hw, E1000_CTRL, ctrl); + + while (timeout) { + if (!(E1000_READ_REG(hw, E1000_STATUS) & + E1000_STATUS_GIO_MASTER_ENABLE)) + break; + usec_delay(100); + timeout--; + } + + if (!timeout) { + DEBUGOUT("Master requests are pending.\n"); + ret_val = -E1000_ERR_MASTER_REQUESTS_PENDING; + goto out; + } + +out: + return ret_val; +} + +/** + * e1000_reset_adaptive_generic - Reset Adaptive Interframe Spacing + * @hw: pointer to the HW structure + * + * Reset the Adaptive Interframe Spacing throttle to default values. + **/ +void e1000_reset_adaptive_generic(struct e1000_hw *hw) +{ + struct e1000_mac_info *mac = &hw->mac; + + DEBUGFUNC("e1000_reset_adaptive_generic"); + + if (!mac->adaptive_ifs) { + DEBUGOUT("Not in Adaptive IFS mode!\n"); + goto out; + } + + mac->current_ifs_val = 0; + mac->ifs_min_val = IFS_MIN; + mac->ifs_max_val = IFS_MAX; + mac->ifs_step_size = IFS_STEP; + mac->ifs_ratio = IFS_RATIO; + + mac->in_ifs_mode = FALSE; + E1000_WRITE_REG(hw, E1000_AIT, 0); +out: + return; +} + +/** + * e1000_update_adaptive_generic - Update Adaptive Interframe Spacing + * @hw: pointer to the HW structure + * + * Update the Adaptive Interframe Spacing Throttle value based on the + * time between transmitted packets and time between collisions. + **/ +void e1000_update_adaptive_generic(struct e1000_hw *hw) +{ + struct e1000_mac_info *mac = &hw->mac; + + DEBUGFUNC("e1000_update_adaptive_generic"); + + if (!mac->adaptive_ifs) { + DEBUGOUT("Not in Adaptive IFS mode!\n"); + goto out; + } + + if ((mac->collision_delta * mac->ifs_ratio) > mac->tx_packet_delta) { + if (mac->tx_packet_delta > MIN_NUM_XMITS) { + mac->in_ifs_mode = TRUE; + if (mac->current_ifs_val < mac->ifs_max_val) { + if (!mac->current_ifs_val) + mac->current_ifs_val = mac->ifs_min_val; + else + mac->current_ifs_val += + mac->ifs_step_size; + E1000_WRITE_REG(hw, E1000_AIT, mac->current_ifs_val); + } + } + } else { + if (mac->in_ifs_mode && + (mac->tx_packet_delta <= MIN_NUM_XMITS)) { + mac->current_ifs_val = 0; + mac->in_ifs_mode = FALSE; + E1000_WRITE_REG(hw, E1000_AIT, 0); + } + } +out: + return; +} + +/** + * e1000_validate_mdi_setting_generic - Verify MDI/MDIx settings + * @hw: pointer to the HW structure + * + * Verify that when not using auto-negotiation that MDI/MDIx is correctly + * set, which is forced to MDI mode only. + **/ +s32 e1000_validate_mdi_setting_generic(struct e1000_hw *hw) +{ + s32 ret_val = E1000_SUCCESS; + + DEBUGFUNC("e1000_validate_mdi_setting_generic"); + + if (!hw->mac.autoneg && (hw->phy.mdix == 0 || hw->phy.mdix == 3)) { + DEBUGOUT("Invalid MDI setting detected\n"); + hw->phy.mdix = 1; + ret_val = -E1000_ERR_CONFIG; + goto out; + } + +out: + return ret_val; +} + +/** + * e1000_write_8bit_ctrl_reg_generic - Write a 8bit CTRL register + * @hw: pointer to the HW structure + * @reg: 32bit register offset such as E1000_SCTL + * @offset: register offset to write to + * @data: data to write at register offset + * + * Writes an address/data control type register. There are several of these + * and they all have the format address << 8 | data and bit 31 is polled for + * completion. + **/ +s32 e1000_write_8bit_ctrl_reg_generic(struct e1000_hw *hw, u32 reg, + u32 offset, u8 data) +{ + u32 i, regvalue = 0; + s32 ret_val = E1000_SUCCESS; + + DEBUGFUNC("e1000_write_8bit_ctrl_reg_generic"); + + /* Set up the address and data */ + regvalue = ((u32)data) | (offset << E1000_GEN_CTL_ADDRESS_SHIFT); + E1000_WRITE_REG(hw, reg, regvalue); + + /* Poll the ready bit to see if the MDI read completed */ + for (i = 0; i < E1000_GEN_POLL_TIMEOUT; i++) { + usec_delay(5); + regvalue = E1000_READ_REG(hw, reg); + if (regvalue & E1000_GEN_CTL_READY) + break; + } + if (!(regvalue & E1000_GEN_CTL_READY)) { + DEBUGOUT1("Reg %08x did not indicate ready\n", reg); + ret_val = -E1000_ERR_PHY; + goto out; + } + +out: + return ret_val; +} diff --git a/sys/dev/netif/ig_hal/e1000_mac.h b/sys/dev/netif/ig_hal/e1000_mac.h new file mode 100644 index 0000000000..7f9baa9093 --- /dev/null +++ b/sys/dev/netif/ig_hal/e1000_mac.h @@ -0,0 +1,102 @@ +/****************************************************************************** + + Copyright (c) 2001-2008, Intel Corporation + All rights reserved. + + Redistribution and use in source and binary forms, with or without + modification, are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, + this list of conditions and the following disclaimer. + + 2. Redistributions in binary form must reproduce the above copyright + notice, this list of conditions and the following disclaimer in the + documentation and/or other materials provided with the distribution. + + 3. Neither the name of the Intel Corporation nor the names of its + contributors may be used to endorse or promote products derived from + this software without specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE + ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE + LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR + CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF + SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS + INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN + CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) + ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + POSSIBILITY OF SUCH DAMAGE. + +******************************************************************************/ +/*$FreeBSD$*/ + +#ifndef _E1000_MAC_H_ +#define _E1000_MAC_H_ + +/* + * Functions that should not be called directly from drivers but can be used + * by other files in this 'shared code' + */ +void e1000_init_mac_ops_generic(struct e1000_hw *hw); +void e1000_null_mac_generic(struct e1000_hw *hw); +s32 e1000_null_ops_generic(struct e1000_hw *hw); +s32 e1000_null_link_info(struct e1000_hw *hw, u16 *s, u16 *d); +bool e1000_null_mng_mode(struct e1000_hw *hw); +void e1000_null_update_mc(struct e1000_hw *hw, u8 *h, u32 a, u32 b, u32 c); +void e1000_null_write_vfta(struct e1000_hw *hw, u32 a, u32 b); +void e1000_null_mta_set(struct e1000_hw *hw, u32 a); +void e1000_null_rar_set(struct e1000_hw *hw, u8 *h, u32 a); +s32 e1000_blink_led_generic(struct e1000_hw *hw); +s32 e1000_check_for_copper_link_generic(struct e1000_hw *hw); +s32 e1000_check_for_fiber_link_generic(struct e1000_hw *hw); +s32 e1000_check_for_serdes_link_generic(struct e1000_hw *hw); +s32 e1000_cleanup_led_generic(struct e1000_hw *hw); +s32 e1000_commit_fc_settings_generic(struct e1000_hw *hw); +s32 e1000_poll_fiber_serdes_link_generic(struct e1000_hw *hw); +s32 e1000_config_fc_after_link_up_generic(struct e1000_hw *hw); +s32 e1000_disable_pcie_master_generic(struct e1000_hw *hw); +s32 e1000_force_mac_fc_generic(struct e1000_hw *hw); +s32 e1000_get_auto_rd_done_generic(struct e1000_hw *hw); +s32 e1000_get_bus_info_pci_generic(struct e1000_hw *hw); +s32 e1000_get_bus_info_pcie_generic(struct e1000_hw *hw); +void e1000_set_lan_id_single_port(struct e1000_hw *hw); +void e1000_set_lan_id_multi_port_pci(struct e1000_hw *hw); +void e1000_set_lan_id_multi_port_pcie(struct e1000_hw *hw); +s32 e1000_get_hw_semaphore_generic(struct e1000_hw *hw); +s32 e1000_get_speed_and_duplex_copper_generic(struct e1000_hw *hw, u16 *speed, + u16 *duplex); +s32 e1000_get_speed_and_duplex_fiber_serdes_generic(struct e1000_hw *hw, + u16 *speed, u16 *duplex); +s32 e1000_id_led_init_generic(struct e1000_hw *hw); +s32 e1000_led_on_generic(struct e1000_hw *hw); +s32 e1000_led_off_generic(struct e1000_hw *hw); +void e1000_update_mc_addr_list_generic(struct e1000_hw *hw, + u8 *mc_addr_list, u32 mc_addr_count, + u32 rar_used_count, u32 rar_count); +s32 e1000_set_default_fc_generic(struct e1000_hw *hw); +s32 e1000_set_fc_watermarks_generic(struct e1000_hw *hw); +s32 e1000_setup_fiber_serdes_link_generic(struct e1000_hw *hw); +s32 e1000_setup_led_generic(struct e1000_hw *hw); +s32 e1000_setup_link_generic(struct e1000_hw *hw); +s32 e1000_write_8bit_ctrl_reg_generic(struct e1000_hw *hw, u32 reg, + u32 offset, u8 data); + +u32 e1000_hash_mc_addr_generic(struct e1000_hw *hw, u8 *mc_addr); + +void e1000_clear_hw_cntrs_base_generic(struct e1000_hw *hw); +void e1000_clear_vfta_generic(struct e1000_hw *hw); +void e1000_config_collision_dist_generic(struct e1000_hw *hw); +void e1000_init_rx_addrs_generic(struct e1000_hw *hw, u16 rar_count); +void e1000_mta_set_generic(struct e1000_hw *hw, u32 hash_value); +void e1000_pcix_mmrbc_workaround_generic(struct e1000_hw *hw); +void e1000_put_hw_semaphore_generic(struct e1000_hw *hw); +void e1000_rar_set_generic(struct e1000_hw *hw, u8 *addr, u32 index); +s32 e1000_check_alt_mac_addr_generic(struct e1000_hw *hw); +void e1000_reset_adaptive_generic(struct e1000_hw *hw); +void e1000_set_pcie_no_snoop_generic(struct e1000_hw *hw, u32 no_snoop); +void e1000_update_adaptive_generic(struct e1000_hw *hw); +void e1000_write_vfta_generic(struct e1000_hw *hw, u32 offset, u32 value); + +#endif diff --git a/sys/dev/netif/ig_hal/e1000_manage.c b/sys/dev/netif/ig_hal/e1000_manage.c new file mode 100644 index 0000000000..b1f6541ad0 --- /dev/null +++ b/sys/dev/netif/ig_hal/e1000_manage.c @@ -0,0 +1,390 @@ +/****************************************************************************** + + Copyright (c) 2001-2008, Intel Corporation + All rights reserved. + + Redistribution and use in source and binary forms, with or without + modification, are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, + this list of conditions and the following disclaimer. + + 2. Redistributions in binary form must reproduce the above copyright + notice, this list of conditions and the following disclaimer in the + documentation and/or other materials provided with the distribution. + + 3. Neither the name of the Intel Corporation nor the names of its + contributors may be used to endorse or promote products derived from + this software without specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE + ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE + LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR + CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF + SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS + INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN + CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) + ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + POSSIBILITY OF SUCH DAMAGE. + +******************************************************************************/ +/*$FreeBSD$*/ + +#include "e1000_api.h" + +static u8 e1000_calculate_checksum(u8 *buffer, u32 length); + +/** + * e1000_calculate_checksum - Calculate checksum for buffer + * @buffer: pointer to EEPROM + * @length: size of EEPROM to calculate a checksum for + * + * Calculates the checksum for some buffer on a specified length. The + * checksum calculated is returned. + **/ +static u8 e1000_calculate_checksum(u8 *buffer, u32 length) +{ + u32 i; + u8 sum = 0; + + DEBUGFUNC("e1000_calculate_checksum"); + + if (!buffer) + return 0; + + for (i = 0; i < length; i++) + sum += buffer[i]; + + return (u8) (0 - sum); +} + +/** + * e1000_mng_enable_host_if_generic - Checks host interface is enabled + * @hw: pointer to the HW structure + * + * Returns E1000_success upon success, else E1000_ERR_HOST_INTERFACE_COMMAND + * + * This function checks whether the HOST IF is enabled for command operation + * and also checks whether the previous command is completed. It busy waits + * in case of previous command is not completed. + **/ +s32 e1000_mng_enable_host_if_generic(struct e1000_hw *hw) +{ + u32 hicr; + s32 ret_val = E1000_SUCCESS; + u8 i; + + DEBUGFUNC("e1000_mng_enable_host_if_generic"); + + /* Check that the host interface is enabled. */ + hicr = E1000_READ_REG(hw, E1000_HICR); + if ((hicr & E1000_HICR_EN) == 0) { + DEBUGOUT("E1000_HOST_EN bit disabled.\n"); + ret_val = -E1000_ERR_HOST_INTERFACE_COMMAND; + goto out; + } + /* check the previous command is completed */ + for (i = 0; i < E1000_MNG_DHCP_COMMAND_TIMEOUT; i++) { + hicr = E1000_READ_REG(hw, E1000_HICR); + if (!(hicr & E1000_HICR_C)) + break; + msec_delay_irq(1); + } + + if (i == E1000_MNG_DHCP_COMMAND_TIMEOUT) { + DEBUGOUT("Previous command timeout failed .\n"); + ret_val = -E1000_ERR_HOST_INTERFACE_COMMAND; + goto out; + } + +out: + return ret_val; +} + +/** + * e1000_check_mng_mode_generic - Generic check management mode + * @hw: pointer to the HW structure + * + * Reads the firmware semaphore register and returns TRUE (>0) if + * manageability is enabled, else FALSE (0). + **/ +bool e1000_check_mng_mode_generic(struct e1000_hw *hw) +{ + u32 fwsm; + + DEBUGFUNC("e1000_check_mng_mode_generic"); + + fwsm = E1000_READ_REG(hw, E1000_FWSM); + + return (fwsm & E1000_FWSM_MODE_MASK) == + (E1000_MNG_IAMT_MODE << E1000_FWSM_MODE_SHIFT); +} + +/** + * e1000_enable_tx_pkt_filtering_generic - Enable packet filtering on TX + * @hw: pointer to the HW structure + * + * Enables packet filtering on transmit packets if manageability is enabled + * and host interface is enabled. + **/ +bool e1000_enable_tx_pkt_filtering_generic(struct e1000_hw *hw) +{ + struct e1000_host_mng_dhcp_cookie *hdr = &hw->mng_cookie; + u32 *buffer = (u32 *)&hw->mng_cookie; + u32 offset; + s32 ret_val, hdr_csum, csum; + u8 i, len; + bool tx_filter = TRUE; + + DEBUGFUNC("e1000_enable_tx_pkt_filtering_generic"); + + /* No manageability, no filtering */ + if (!hw->mac.ops.check_mng_mode(hw)) { + tx_filter = FALSE; + goto out; + } + + /* + * If we can't read from the host interface for whatever + * reason, disable filtering. + */ + ret_val = hw->mac.ops.mng_enable_host_if(hw); + if (ret_val != E1000_SUCCESS) { + tx_filter = FALSE; + goto out; + } + + /* Read in the header. Length and offset are in dwords. */ + len = E1000_MNG_DHCP_COOKIE_LENGTH >> 2; + offset = E1000_MNG_DHCP_COOKIE_OFFSET >> 2; + for (i = 0; i < len; i++) { + *(buffer + i) = E1000_READ_REG_ARRAY_DWORD(hw, + E1000_HOST_IF, + offset + i); + } + hdr_csum = hdr->checksum; + hdr->checksum = 0; + csum = e1000_calculate_checksum((u8 *)hdr, + E1000_MNG_DHCP_COOKIE_LENGTH); + /* + * If either the checksums or signature don't match, then + * the cookie area isn't considered valid, in which case we + * take the safe route of assuming Tx filtering is enabled. + */ + if (hdr_csum != csum) + goto out; + if (hdr->signature != E1000_IAMT_SIGNATURE) + goto out; + + /* Cookie area is valid, make the final check for filtering. */ + if (!(hdr->status & E1000_MNG_DHCP_COOKIE_STATUS_PARSING)) + tx_filter = FALSE; + +out: + hw->mac.tx_pkt_filtering = tx_filter; + return tx_filter; +} + +/** + * e1000_mng_write_dhcp_info_generic - Writes DHCP info to host interface + * @hw: pointer to the HW structure + * @buffer: pointer to the host interface + * @length: size of the buffer + * + * Writes the DHCP information to the host interface. + **/ +s32 e1000_mng_write_dhcp_info_generic(struct e1000_hw *hw, u8 *buffer, + u16 length) +{ + struct e1000_host_mng_command_header hdr; + s32 ret_val; + u32 hicr; + + DEBUGFUNC("e1000_mng_write_dhcp_info_generic"); + + hdr.command_id = E1000_MNG_DHCP_TX_PAYLOAD_CMD; + hdr.command_length = length; + hdr.reserved1 = 0; + hdr.reserved2 = 0; + hdr.checksum = 0; + + /* Enable the host interface */ + ret_val = hw->mac.ops.mng_enable_host_if(hw); + if (ret_val) + goto out; + + /* Populate the host interface with the contents of "buffer". */ + ret_val = hw->mac.ops.mng_host_if_write(hw, buffer, length, + sizeof(hdr), &(hdr.checksum)); + if (ret_val) + goto out; + + /* Write the manageability command header */ + ret_val = hw->mac.ops.mng_write_cmd_header(hw, &hdr); + if (ret_val) + goto out; + + /* Tell the ARC a new command is pending. */ + hicr = E1000_READ_REG(hw, E1000_HICR); + E1000_WRITE_REG(hw, E1000_HICR, hicr | E1000_HICR_C); + +out: + return ret_val; +} + +/** + * e1000_mng_write_cmd_header_generic - Writes manageability command header + * @hw: pointer to the HW structure + * @hdr: pointer to the host interface command header + * + * Writes the command header after does the checksum calculation. + **/ +s32 e1000_mng_write_cmd_header_generic(struct e1000_hw *hw, + struct e1000_host_mng_command_header *hdr) +{ + u16 i, length = sizeof(struct e1000_host_mng_command_header); + + DEBUGFUNC("e1000_mng_write_cmd_header_generic"); + + /* Write the whole command header structure with new checksum. */ + + hdr->checksum = e1000_calculate_checksum((u8 *)hdr, length); + + length >>= 2; + /* Write the relevant command block into the ram area. */ + for (i = 0; i < length; i++) { + E1000_WRITE_REG_ARRAY_DWORD(hw, E1000_HOST_IF, i, + *((u32 *) hdr + i)); + E1000_WRITE_FLUSH(hw); + } + + return E1000_SUCCESS; +} + +/** + * e1000_mng_host_if_write_generic - Write to the manageability host interface + * @hw: pointer to the HW structure + * @buffer: pointer to the host interface buffer + * @length: size of the buffer + * @offset: location in the buffer to write to + * @sum: sum of the data (not checksum) + * + * This function writes the buffer content at the offset given on the host if. + * It also does alignment considerations to do the writes in most efficient + * way. Also fills up the sum of the buffer in *buffer parameter. + **/ +s32 e1000_mng_host_if_write_generic(struct e1000_hw *hw, u8 *buffer, + u16 length, u16 offset, u8 *sum) +{ + u8 *tmp; + u8 *bufptr = buffer; + u32 data = 0; + s32 ret_val = E1000_SUCCESS; + u16 remaining, i, j, prev_bytes; + + DEBUGFUNC("e1000_mng_host_if_write_generic"); + + /* sum = only sum of the data and it is not checksum */ + + if (length == 0 || offset + length > E1000_HI_MAX_MNG_DATA_LENGTH) { + ret_val = -E1000_ERR_PARAM; + goto out; + } + + tmp = (u8 *)&data; + prev_bytes = offset & 0x3; + offset >>= 2; + + if (prev_bytes) { + data = E1000_READ_REG_ARRAY_DWORD(hw, E1000_HOST_IF, offset); + for (j = prev_bytes; j < sizeof(u32); j++) { + *(tmp + j) = *bufptr++; + *sum += *(tmp + j); + } + E1000_WRITE_REG_ARRAY_DWORD(hw, E1000_HOST_IF, offset, data); + length -= j - prev_bytes; + offset++; + } + + remaining = length & 0x3; + length -= remaining; + + /* Calculate length in DWORDs */ + length >>= 2; + + /* + * The device driver writes the relevant command block into the + * ram area. + */ + for (i = 0; i < length; i++) { + for (j = 0; j < sizeof(u32); j++) { + *(tmp + j) = *bufptr++; + *sum += *(tmp + j); + } + + E1000_WRITE_REG_ARRAY_DWORD(hw, E1000_HOST_IF, offset + i, + data); + } + if (remaining) { + for (j = 0; j < sizeof(u32); j++) { + if (j < remaining) + *(tmp + j) = *bufptr++; + else + *(tmp + j) = 0; + + *sum += *(tmp + j); + } + E1000_WRITE_REG_ARRAY_DWORD(hw, E1000_HOST_IF, offset + i, data); + } + +out: + return ret_val; +} + +/** + * e1000_enable_mng_pass_thru - Enable processing of ARP's + * @hw: pointer to the HW structure + * + * Verifies the hardware needs to allow ARPs to be processed by the host. + **/ +bool e1000_enable_mng_pass_thru(struct e1000_hw *hw) +{ + u32 manc; + u32 fwsm, factps; + bool ret_val = FALSE; + + DEBUGFUNC("e1000_enable_mng_pass_thru"); + + if (!hw->mac.asf_firmware_present) + goto out; + + manc = E1000_READ_REG(hw, E1000_MANC); + + if (!(manc & E1000_MANC_RCV_TCO_EN) || + !(manc & E1000_MANC_EN_MAC_ADDR_FILTER)) + goto out; + + if (hw->mac.arc_subsystem_valid) { + fwsm = E1000_READ_REG(hw, E1000_FWSM); + factps = E1000_READ_REG(hw, E1000_FACTPS); + + if (!(factps & E1000_FACTPS_MNGCG) && + ((fwsm & E1000_FWSM_MODE_MASK) == + (e1000_mng_mode_pt << E1000_FWSM_MODE_SHIFT))) { + ret_val = TRUE; + goto out; + } + } else { + if ((manc & E1000_MANC_SMBUS_EN) && + !(manc & E1000_MANC_ASF_EN)) { + ret_val = TRUE; + goto out; + } + } + +out: + return ret_val; +} + diff --git a/sys/dev/netif/ig_hal/e1000_manage.h b/sys/dev/netif/ig_hal/e1000_manage.h new file mode 100644 index 0000000000..146caeb58b --- /dev/null +++ b/sys/dev/netif/ig_hal/e1000_manage.h @@ -0,0 +1,88 @@ +/****************************************************************************** + + Copyright (c) 2001-2008, Intel Corporation + All rights reserved. + + Redistribution and use in source and binary forms, with or without + modification, are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, + this list of conditions and the following disclaimer. + + 2. Redistributions in binary form must reproduce the above copyright + notice, this list of conditions and the following disclaimer in the + documentation and/or other materials provided with the distribution. + + 3. Neither the name of the Intel Corporation nor the names of its + contributors may be used to endorse or promote products derived from + this software without specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE + ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE + LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR + CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF + SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS + INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN + CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) + ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + POSSIBILITY OF SUCH DAMAGE. + +******************************************************************************/ +/*$FreeBSD$*/ + +#ifndef _E1000_MANAGE_H_ +#define _E1000_MANAGE_H_ + +bool e1000_check_mng_mode_generic(struct e1000_hw *hw); +bool e1000_enable_tx_pkt_filtering_generic(struct e1000_hw *hw); +s32 e1000_mng_enable_host_if_generic(struct e1000_hw *hw); +s32 e1000_mng_host_if_write_generic(struct e1000_hw *hw, u8 *buffer, + u16 length, u16 offset, u8 *sum); +s32 e1000_mng_write_cmd_header_generic(struct e1000_hw *hw, + struct e1000_host_mng_command_header *hdr); +s32 e1000_mng_write_dhcp_info_generic(struct e1000_hw *hw, + u8 *buffer, u16 length); +bool e1000_enable_mng_pass_thru(struct e1000_hw *hw); + +enum e1000_mng_mode { + e1000_mng_mode_none = 0, + e1000_mng_mode_asf, + e1000_mng_mode_pt, + e1000_mng_mode_ipmi, + e1000_mng_mode_host_if_only +}; + +#define E1000_FACTPS_MNGCG 0x20000000 + +#define E1000_FWSM_MODE_MASK 0xE +#define E1000_FWSM_MODE_SHIFT 1 + +#define E1000_MNG_IAMT_MODE 0x3 +#define E1000_MNG_DHCP_COOKIE_LENGTH 0x10 +#define E1000_MNG_DHCP_COOKIE_OFFSET 0x6F0 +#define E1000_MNG_DHCP_COMMAND_TIMEOUT 10 +#define E1000_MNG_DHCP_TX_PAYLOAD_CMD 64 +#define E1000_MNG_DHCP_COOKIE_STATUS_PARSING 0x1 +#define E1000_MNG_DHCP_COOKIE_STATUS_VLAN 0x2 + +#define E1000_VFTA_ENTRY_SHIFT 5 +#define E1000_VFTA_ENTRY_MASK 0x7F +#define E1000_VFTA_ENTRY_BIT_SHIFT_MASK 0x1F + +#define E1000_HI_MAX_BLOCK_BYTE_LENGTH 1792 /* Num of bytes in range */ +#define E1000_HI_MAX_BLOCK_DWORD_LENGTH 448 /* Num of dwords in range */ +#define E1000_HI_COMMAND_TIMEOUT 500 /* Process HI command limit */ + +#define E1000_HICR_EN 0x01 /* Enable bit - RO */ +/* Driver sets this bit when done to put command in RAM */ +#define E1000_HICR_C 0x02 +#define E1000_HICR_SV 0x04 /* Status Validity */ +#define E1000_HICR_FW_RESET_ENABLE 0x40 +#define E1000_HICR_FW_RESET 0x80 + +/* Intel(R) Active Management Technology signature */ +#define E1000_IAMT_SIGNATURE 0x544D4149 + +#endif diff --git a/sys/dev/netif/ig_hal/e1000_nvm.c b/sys/dev/netif/ig_hal/e1000_nvm.c new file mode 100644 index 0000000000..8492d80a75 --- /dev/null +++ b/sys/dev/netif/ig_hal/e1000_nvm.c @@ -0,0 +1,931 @@ +/****************************************************************************** + + Copyright (c) 2001-2008, Intel Corporation + All rights reserved. + + Redistribution and use in source and binary forms, with or without + modification, are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, + this list of conditions and the following disclaimer. + + 2. Redistributions in binary form must reproduce the above copyright + notice, this list of conditions and the following disclaimer in the + documentation and/or other materials provided with the distribution. + + 3. Neither the name of the Intel Corporation nor the names of its + contributors may be used to endorse or promote products derived from + this software without specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE + ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE + LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR + CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF + SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS + INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN + CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) + ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + POSSIBILITY OF SUCH DAMAGE. + +******************************************************************************/ +/*$FreeBSD$*/ + +#include "e1000_api.h" + +/** + * e1000_init_nvm_ops_generic - Initialize NVM function pointers + * @hw: pointer to the HW structure + * + * Setups up the function pointers to no-op functions + **/ +void e1000_init_nvm_ops_generic(struct e1000_hw *hw) +{ + struct e1000_nvm_info *nvm = &hw->nvm; + DEBUGFUNC("e1000_init_nvm_ops_generic"); + + /* Initialize function pointers */ + nvm->ops.init_params = e1000_null_ops_generic; + nvm->ops.acquire = e1000_null_ops_generic; + nvm->ops.read = e1000_null_read_nvm; + nvm->ops.release = e1000_null_nvm_generic; + nvm->ops.reload = e1000_reload_nvm_generic; + nvm->ops.update = e1000_null_ops_generic; + nvm->ops.valid_led_default = e1000_null_led_default; + nvm->ops.validate = e1000_null_ops_generic; + nvm->ops.write = e1000_null_write_nvm; +} + +/** + * e1000_null_nvm_read - No-op function, return 0 + * @hw: pointer to the HW structure + **/ +s32 e1000_null_read_nvm(struct e1000_hw *hw, u16 a, u16 b, u16 *c) +{ + DEBUGFUNC("e1000_null_read_nvm"); + return E1000_SUCCESS; +} + +/** + * e1000_null_nvm_generic - No-op function, return void + * @hw: pointer to the HW structure + **/ +void e1000_null_nvm_generic(struct e1000_hw *hw) +{ + DEBUGFUNC("e1000_null_nvm_generic"); + return; +} + +/** + * e1000_null_led_default - No-op function, return 0 + * @hw: pointer to the HW structure + **/ +s32 e1000_null_led_default(struct e1000_hw *hw, u16 *data) +{ + DEBUGFUNC("e1000_null_led_default"); + return E1000_SUCCESS; +} + +/** + * e1000_null_write_nvm - No-op function, return 0 + * @hw: pointer to the HW structure + **/ +s32 e1000_null_write_nvm(struct e1000_hw *hw, u16 a, u16 b, u16 *c) +{ + DEBUGFUNC("e1000_null_write_nvm"); + return E1000_SUCCESS; +} + +/** + * e1000_raise_eec_clk - Raise EEPROM clock + * @hw: pointer to the HW structure + * @eecd: pointer to the EEPROM + * + * Enable/Raise the EEPROM clock bit. + **/ +static void e1000_raise_eec_clk(struct e1000_hw *hw, u32 *eecd) +{ + *eecd = *eecd | E1000_EECD_SK; + E1000_WRITE_REG(hw, E1000_EECD, *eecd); + E1000_WRITE_FLUSH(hw); + usec_delay(hw->nvm.delay_usec); +} + +/** + * e1000_lower_eec_clk - Lower EEPROM clock + * @hw: pointer to the HW structure + * @eecd: pointer to the EEPROM + * + * Clear/Lower the EEPROM clock bit. + **/ +static void e1000_lower_eec_clk(struct e1000_hw *hw, u32 *eecd) +{ + *eecd = *eecd & ~E1000_EECD_SK; + E1000_WRITE_REG(hw, E1000_EECD, *eecd); + E1000_WRITE_FLUSH(hw); + usec_delay(hw->nvm.delay_usec); +} + +/** + * e1000_shift_out_eec_bits - Shift data bits our to the EEPROM + * @hw: pointer to the HW structure + * @data: data to send to the EEPROM + * @count: number of bits to shift out + * + * We need to shift 'count' bits out to the EEPROM. So, the value in the + * "data" parameter will be shifted out to the EEPROM one bit at a time. + * In order to do this, "data" must be broken down into bits. + **/ +static void e1000_shift_out_eec_bits(struct e1000_hw *hw, u16 data, u16 count) +{ + struct e1000_nvm_info *nvm = &hw->nvm; + u32 eecd = E1000_READ_REG(hw, E1000_EECD); + u32 mask; + + DEBUGFUNC("e1000_shift_out_eec_bits"); + + mask = 0x01 << (count - 1); + if (nvm->type == e1000_nvm_eeprom_microwire) + eecd &= ~E1000_EECD_DO; + else + if (nvm->type == e1000_nvm_eeprom_spi) + eecd |= E1000_EECD_DO; + + do { + eecd &= ~E1000_EECD_DI; + + if (data & mask) + eecd |= E1000_EECD_DI; + + E1000_WRITE_REG(hw, E1000_EECD, eecd); + E1000_WRITE_FLUSH(hw); + + usec_delay(nvm->delay_usec); + + e1000_raise_eec_clk(hw, &eecd); + e1000_lower_eec_clk(hw, &eecd); + + mask >>= 1; + } while (mask); + + eecd &= ~E1000_EECD_DI; + E1000_WRITE_REG(hw, E1000_EECD, eecd); +} + +/** + * e1000_shift_in_eec_bits - Shift data bits in from the EEPROM + * @hw: pointer to the HW structure + * @count: number of bits to shift in + * + * In order to read a register from the EEPROM, we need to shift 'count' bits + * in from the EEPROM. Bits are "shifted in" by raising the clock input to + * the EEPROM (setting the SK bit), and then reading the value of the data out + * "DO" bit. During this "shifting in" process the data in "DI" bit should + * always be clear. + **/ +static u16 e1000_shift_in_eec_bits(struct e1000_hw *hw, u16 count) +{ + u32 eecd; + u32 i; + u16 data; + + DEBUGFUNC("e1000_shift_in_eec_bits"); + + eecd = E1000_READ_REG(hw, E1000_EECD); + + eecd &= ~(E1000_EECD_DO | E1000_EECD_DI); + data = 0; + + for (i = 0; i < count; i++) { + data <<= 1; + e1000_raise_eec_clk(hw, &eecd); + + eecd = E1000_READ_REG(hw, E1000_EECD); + + eecd &= ~E1000_EECD_DI; + if (eecd & E1000_EECD_DO) + data |= 1; + + e1000_lower_eec_clk(hw, &eecd); + } + + return data; +} + +/** + * e1000_poll_eerd_eewr_done - Poll for EEPROM read/write completion + * @hw: pointer to the HW structure + * @ee_reg: EEPROM flag for polling + * + * Polls the EEPROM status bit for either read or write completion based + * upon the value of 'ee_reg'. + **/ +s32 e1000_poll_eerd_eewr_done(struct e1000_hw *hw, int ee_reg) +{ + u32 attempts = 100000; + u32 i, reg = 0; + s32 ret_val = -E1000_ERR_NVM; + + DEBUGFUNC("e1000_poll_eerd_eewr_done"); + + for (i = 0; i < attempts; i++) { + if (ee_reg == E1000_NVM_POLL_READ) + reg = E1000_READ_REG(hw, E1000_EERD); + else + reg = E1000_READ_REG(hw, E1000_EEWR); + + if (reg & E1000_NVM_RW_REG_DONE) { + ret_val = E1000_SUCCESS; + break; + } + + usec_delay(5); + } + + return ret_val; +} + +/** + * e1000_acquire_nvm_generic - Generic request for access to EEPROM + * @hw: pointer to the HW structure + * + * Set the EEPROM access request bit and wait for EEPROM access grant bit. + * Return successful if access grant bit set, else clear the request for + * EEPROM access and return -E1000_ERR_NVM (-1). + **/ +s32 e1000_acquire_nvm_generic(struct e1000_hw *hw) +{ + u32 eecd = E1000_READ_REG(hw, E1000_EECD); + s32 timeout = E1000_NVM_GRANT_ATTEMPTS; + s32 ret_val = E1000_SUCCESS; + + DEBUGFUNC("e1000_acquire_nvm_generic"); + + E1000_WRITE_REG(hw, E1000_EECD, eecd | E1000_EECD_REQ); + eecd = E1000_READ_REG(hw, E1000_EECD); + + while (timeout) { + if (eecd & E1000_EECD_GNT) + break; + usec_delay(5); + eecd = E1000_READ_REG(hw, E1000_EECD); + timeout--; + } + + if (!timeout) { + eecd &= ~E1000_EECD_REQ; + E1000_WRITE_REG(hw, E1000_EECD, eecd); + DEBUGOUT("Could not acquire NVM grant\n"); + ret_val = -E1000_ERR_NVM; + } + + return ret_val; +} + +/** + * e1000_standby_nvm - Return EEPROM to standby state + * @hw: pointer to the HW structure + * + * Return the EEPROM to a standby state. + **/ +static void e1000_standby_nvm(struct e1000_hw *hw) +{ + struct e1000_nvm_info *nvm = &hw->nvm; + u32 eecd = E1000_READ_REG(hw, E1000_EECD); + + DEBUGFUNC("e1000_standby_nvm"); + + if (nvm->type == e1000_nvm_eeprom_microwire) { + eecd &= ~(E1000_EECD_CS | E1000_EECD_SK); + E1000_WRITE_REG(hw, E1000_EECD, eecd); + E1000_WRITE_FLUSH(hw); + usec_delay(nvm->delay_usec); + + e1000_raise_eec_clk(hw, &eecd); + + /* Select EEPROM */ + eecd |= E1000_EECD_CS; + E1000_WRITE_REG(hw, E1000_EECD, eecd); + E1000_WRITE_FLUSH(hw); + usec_delay(nvm->delay_usec); + + e1000_lower_eec_clk(hw, &eecd); + } else + if (nvm->type == e1000_nvm_eeprom_spi) { + /* Toggle CS to flush commands */ + eecd |= E1000_EECD_CS; + E1000_WRITE_REG(hw, E1000_EECD, eecd); + E1000_WRITE_FLUSH(hw); + usec_delay(nvm->delay_usec); + eecd &= ~E1000_EECD_CS; + E1000_WRITE_REG(hw, E1000_EECD, eecd); + E1000_WRITE_FLUSH(hw); + usec_delay(nvm->delay_usec); + } +} + +/** + * e1000_stop_nvm - Terminate EEPROM command + * @hw: pointer to the HW structure + * + * Terminates the current command by inverting the EEPROM's chip select pin. + **/ +void e1000_stop_nvm(struct e1000_hw *hw) +{ + u32 eecd; + + DEBUGFUNC("e1000_stop_nvm"); + + eecd = E1000_READ_REG(hw, E1000_EECD); + if (hw->nvm.type == e1000_nvm_eeprom_spi) { + /* Pull CS high */ + eecd |= E1000_EECD_CS; + e1000_lower_eec_clk(hw, &eecd); + } else if (hw->nvm.type == e1000_nvm_eeprom_microwire) { + /* CS on Microwire is active-high */ + eecd &= ~(E1000_EECD_CS | E1000_EECD_DI); + E1000_WRITE_REG(hw, E1000_EECD, eecd); + e1000_raise_eec_clk(hw, &eecd); + e1000_lower_eec_clk(hw, &eecd); + } +} + +/** + * e1000_release_nvm_generic - Release exclusive access to EEPROM + * @hw: pointer to the HW structure + * + * Stop any current commands to the EEPROM and clear the EEPROM request bit. + **/ +void e1000_release_nvm_generic(struct e1000_hw *hw) +{ + u32 eecd; + + DEBUGFUNC("e1000_release_nvm_generic"); + + e1000_stop_nvm(hw); + + eecd = E1000_READ_REG(hw, E1000_EECD); + eecd &= ~E1000_EECD_REQ; + E1000_WRITE_REG(hw, E1000_EECD, eecd); +} + +/** + * e1000_ready_nvm_eeprom - Prepares EEPROM for read/write + * @hw: pointer to the HW structure + * + * Setups the EEPROM for reading and writing. + **/ +static s32 e1000_ready_nvm_eeprom(struct e1000_hw *hw) +{ + struct e1000_nvm_info *nvm = &hw->nvm; + u32 eecd = E1000_READ_REG(hw, E1000_EECD); + s32 ret_val = E1000_SUCCESS; + u16 timeout = 0; + u8 spi_stat_reg; + + DEBUGFUNC("e1000_ready_nvm_eeprom"); + + if (nvm->type == e1000_nvm_eeprom_microwire) { + /* Clear SK and DI */ + eecd &= ~(E1000_EECD_DI | E1000_EECD_SK); + E1000_WRITE_REG(hw, E1000_EECD, eecd); + /* Set CS */ + eecd |= E1000_EECD_CS; + E1000_WRITE_REG(hw, E1000_EECD, eecd); + } else + if (nvm->type == e1000_nvm_eeprom_spi) { + /* Clear SK and CS */ + eecd &= ~(E1000_EECD_CS | E1000_EECD_SK); + E1000_WRITE_REG(hw, E1000_EECD, eecd); + usec_delay(1); + timeout = NVM_MAX_RETRY_SPI; + + /* + * Read "Status Register" repeatedly until the LSB is cleared. + * The EEPROM will signal that the command has been completed + * by clearing bit 0 of the internal status register. If it's + * not cleared within 'timeout', then error out. + */ + while (timeout) { + e1000_shift_out_eec_bits(hw, NVM_RDSR_OPCODE_SPI, + hw->nvm.opcode_bits); + spi_stat_reg = (u8)e1000_shift_in_eec_bits(hw, 8); + if (!(spi_stat_reg & NVM_STATUS_RDY_SPI)) + break; + + usec_delay(5); + e1000_standby_nvm(hw); + timeout--; + } + + if (!timeout) { + DEBUGOUT("SPI NVM Status error\n"); + ret_val = -E1000_ERR_NVM; + goto out; + } + } + +out: + return ret_val; +} + +/** + * e1000_read_nvm_spi - Read EEPROM's using SPI + * @hw: pointer to the HW structure + * @offset: offset of word in the EEPROM to read + * @words: number of words to read + * @data: word read from the EEPROM + * + * Reads a 16 bit word from the EEPROM. + **/ +s32 e1000_read_nvm_spi(struct e1000_hw *hw, u16 offset, u16 words, u16 *data) +{ + struct e1000_nvm_info *nvm = &hw->nvm; + u32 i = 0; + s32 ret_val; + u16 word_in; + u8 read_opcode = NVM_READ_OPCODE_SPI; + + DEBUGFUNC("e1000_read_nvm_spi"); + + /* + * A check for invalid values: offset too large, too many words, + * and not enough words. + */ + if ((offset >= nvm->word_size) || (words > (nvm->word_size - offset)) || + (words == 0)) { + DEBUGOUT("nvm parameter(s) out of bounds\n"); + ret_val = -E1000_ERR_NVM; + goto out; + } + + ret_val = nvm->ops.acquire(hw); + if (ret_val) + goto out; + + ret_val = e1000_ready_nvm_eeprom(hw); + if (ret_val) + goto release; + + e1000_standby_nvm(hw); + + if ((nvm->address_bits == 8) && (offset >= 128)) + read_opcode |= NVM_A8_OPCODE_SPI; + + /* Send the READ command (opcode + addr) */ + e1000_shift_out_eec_bits(hw, read_opcode, nvm->opcode_bits); + e1000_shift_out_eec_bits(hw, (u16)(offset*2), nvm->address_bits); + + /* + * Read the data. SPI NVMs increment the address with each byte + * read and will roll over if reading beyond the end. This allows + * us to read the whole NVM from any offset + */ + for (i = 0; i < words; i++) { + word_in = e1000_shift_in_eec_bits(hw, 16); + data[i] = (word_in >> 8) | (word_in << 8); + } + +release: + nvm->ops.release(hw); + +out: + return ret_val; +} + +/** + * e1000_read_nvm_microwire - Reads EEPROM's using microwire + * @hw: pointer to the HW structure + * @offset: offset of word in the EEPROM to read + * @words: number of words to read + * @data: word read from the EEPROM + * + * Reads a 16 bit word from the EEPROM. + **/ +s32 e1000_read_nvm_microwire(struct e1000_hw *hw, u16 offset, u16 words, + u16 *data) +{ + struct e1000_nvm_info *nvm = &hw->nvm; + u32 i = 0; + s32 ret_val; + u8 read_opcode = NVM_READ_OPCODE_MICROWIRE; + + DEBUGFUNC("e1000_read_nvm_microwire"); + + /* + * A check for invalid values: offset too large, too many words, + * and not enough words. + */ + if ((offset >= nvm->word_size) || (words > (nvm->word_size - offset)) || + (words == 0)) { + DEBUGOUT("nvm parameter(s) out of bounds\n"); + ret_val = -E1000_ERR_NVM; + goto out; + } + + ret_val = nvm->ops.acquire(hw); + if (ret_val) + goto out; + + ret_val = e1000_ready_nvm_eeprom(hw); + if (ret_val) + goto release; + + for (i = 0; i < words; i++) { + /* Send the READ command (opcode + addr) */ + e1000_shift_out_eec_bits(hw, read_opcode, nvm->opcode_bits); + e1000_shift_out_eec_bits(hw, (u16)(offset + i), + nvm->address_bits); + + /* + * Read the data. For microwire, each word requires the + * overhead of setup and tear-down. + */ + data[i] = e1000_shift_in_eec_bits(hw, 16); + e1000_standby_nvm(hw); + } + +release: + nvm->ops.release(hw); + +out: + return ret_val; +} + +/** + * e1000_read_nvm_eerd - Reads EEPROM using EERD register + * @hw: pointer to the HW structure + * @offset: offset of word in the EEPROM to read + * @words: number of words to read + * @data: word read from the EEPROM + * + * Reads a 16 bit word from the EEPROM using the EERD register. + **/ +s32 e1000_read_nvm_eerd(struct e1000_hw *hw, u16 offset, u16 words, u16 *data) +{ + struct e1000_nvm_info *nvm = &hw->nvm; + u32 i, eerd = 0; + s32 ret_val = E1000_SUCCESS; + + DEBUGFUNC("e1000_read_nvm_eerd"); + + /* + * A check for invalid values: offset too large, too many words, + * too many words for the offset, and not enough words. + */ + if ((offset >= nvm->word_size) || (words > (nvm->word_size - offset)) || + (words == 0)) { + DEBUGOUT("nvm parameter(s) out of bounds\n"); + ret_val = -E1000_ERR_NVM; + goto out; + } + + for (i = 0; i < words; i++) { + eerd = ((offset+i) << E1000_NVM_RW_ADDR_SHIFT) + + E1000_NVM_RW_REG_START; + + E1000_WRITE_REG(hw, E1000_EERD, eerd); + ret_val = e1000_poll_eerd_eewr_done(hw, E1000_NVM_POLL_READ); + if (ret_val) + break; + + data[i] = (E1000_READ_REG(hw, E1000_EERD) >> + E1000_NVM_RW_REG_DATA); + } + +out: + return ret_val; +} + +/** + * e1000_write_nvm_spi - Write to EEPROM using SPI + * @hw: pointer to the HW structure + * @offset: offset within the EEPROM to be written to + * @words: number of words to write + * @data: 16 bit word(s) to be written to the EEPROM + * + * Writes data to EEPROM at offset using SPI interface. + * + * If e1000_update_nvm_checksum is not called after this function , the + * EEPROM will most likely contain an invalid checksum. + **/ +s32 e1000_write_nvm_spi(struct e1000_hw *hw, u16 offset, u16 words, u16 *data) +{ + struct e1000_nvm_info *nvm = &hw->nvm; + s32 ret_val; + u16 widx = 0; + + DEBUGFUNC("e1000_write_nvm_spi"); + + /* + * A check for invalid values: offset too large, too many words, + * and not enough words. + */ + if ((offset >= nvm->word_size) || (words > (nvm->word_size - offset)) || + (words == 0)) { + DEBUGOUT("nvm parameter(s) out of bounds\n"); + ret_val = -E1000_ERR_NVM; + goto out; + } + + ret_val = nvm->ops.acquire(hw); + if (ret_val) + goto out; + + while (widx < words) { + u8 write_opcode = NVM_WRITE_OPCODE_SPI; + + ret_val = e1000_ready_nvm_eeprom(hw); + if (ret_val) + goto release; + + e1000_standby_nvm(hw); + + /* Send the WRITE ENABLE command (8 bit opcode) */ + e1000_shift_out_eec_bits(hw, NVM_WREN_OPCODE_SPI, + nvm->opcode_bits); + + e1000_standby_nvm(hw); + + /* + * Some SPI eeproms use the 8th address bit embedded in the + * opcode + */ + if ((nvm->address_bits == 8) && (offset >= 128)) + write_opcode |= NVM_A8_OPCODE_SPI; + + /* Send the Write command (8-bit opcode + addr) */ + e1000_shift_out_eec_bits(hw, write_opcode, nvm->opcode_bits); + e1000_shift_out_eec_bits(hw, (u16)((offset + widx) * 2), + nvm->address_bits); + + /* Loop to allow for up to whole page write of eeprom */ + while (widx < words) { + u16 word_out = data[widx]; + word_out = (word_out >> 8) | (word_out << 8); + e1000_shift_out_eec_bits(hw, word_out, 16); + widx++; + + if ((((offset + widx) * 2) % nvm->page_size) == 0) { + e1000_standby_nvm(hw); + break; + } + } + } + + msec_delay(10); +release: + nvm->ops.release(hw); + +out: + return ret_val; +} + +/** + * e1000_write_nvm_microwire - Writes EEPROM using microwire + * @hw: pointer to the HW structure + * @offset: offset within the EEPROM to be written to + * @words: number of words to write + * @data: 16 bit word(s) to be written to the EEPROM + * + * Writes data to EEPROM at offset using microwire interface. + * + * If e1000_update_nvm_checksum is not called after this function , the + * EEPROM will most likely contain an invalid checksum. + **/ +s32 e1000_write_nvm_microwire(struct e1000_hw *hw, u16 offset, u16 words, + u16 *data) +{ + struct e1000_nvm_info *nvm = &hw->nvm; + s32 ret_val; + u32 eecd; + u16 words_written = 0; + u16 widx = 0; + + DEBUGFUNC("e1000_write_nvm_microwire"); + + /* + * A check for invalid values: offset too large, too many words, + * and not enough words. + */ + if ((offset >= nvm->word_size) || (words > (nvm->word_size - offset)) || + (words == 0)) { + DEBUGOUT("nvm parameter(s) out of bounds\n"); + ret_val = -E1000_ERR_NVM; + goto out; + } + + ret_val = nvm->ops.acquire(hw); + if (ret_val) + goto out; + + ret_val = e1000_ready_nvm_eeprom(hw); + if (ret_val) + goto release; + + e1000_shift_out_eec_bits(hw, NVM_EWEN_OPCODE_MICROWIRE, + (u16)(nvm->opcode_bits + 2)); + + e1000_shift_out_eec_bits(hw, 0, (u16)(nvm->address_bits - 2)); + + e1000_standby_nvm(hw); + + while (words_written < words) { + e1000_shift_out_eec_bits(hw, NVM_WRITE_OPCODE_MICROWIRE, + nvm->opcode_bits); + + e1000_shift_out_eec_bits(hw, (u16)(offset + words_written), + nvm->address_bits); + + e1000_shift_out_eec_bits(hw, data[words_written], 16); + + e1000_standby_nvm(hw); + + for (widx = 0; widx < 200; widx++) { + eecd = E1000_READ_REG(hw, E1000_EECD); + if (eecd & E1000_EECD_DO) + break; + usec_delay(50); + } + + if (widx == 200) { + DEBUGOUT("NVM Write did not complete\n"); + ret_val = -E1000_ERR_NVM; + goto release; + } + + e1000_standby_nvm(hw); + + words_written++; + } + + e1000_shift_out_eec_bits(hw, NVM_EWDS_OPCODE_MICROWIRE, + (u16)(nvm->opcode_bits + 2)); + + e1000_shift_out_eec_bits(hw, 0, (u16)(nvm->address_bits - 2)); + +release: + nvm->ops.release(hw); + +out: + return ret_val; +} + +/** + * e1000_read_pba_num_generic - Read device part number + * @hw: pointer to the HW structure + * @pba_num: pointer to device part number + * + * Reads the product board assembly (PBA) number from the EEPROM and stores + * the value in pba_num. + **/ +s32 e1000_read_pba_num_generic(struct e1000_hw *hw, u32 *pba_num) +{ + s32 ret_val; + u16 nvm_data; + + DEBUGFUNC("e1000_read_pba_num_generic"); + + ret_val = hw->nvm.ops.read(hw, NVM_PBA_OFFSET_0, 1, &nvm_data); + if (ret_val) { + DEBUGOUT("NVM Read Error\n"); + goto out; + } + *pba_num = (u32)(nvm_data << 16); + + ret_val = hw->nvm.ops.read(hw, NVM_PBA_OFFSET_1, 1, &nvm_data); + if (ret_val) { + DEBUGOUT("NVM Read Error\n"); + goto out; + } + *pba_num |= nvm_data; + +out: + return ret_val; +} + +/** + * e1000_read_mac_addr_generic - Read device MAC address + * @hw: pointer to the HW structure + * + * Reads the device MAC address from the EEPROM and stores the value. + * Since devices with two ports use the same EEPROM, we increment the + * last bit in the MAC address for the second port. + **/ +s32 e1000_read_mac_addr_generic(struct e1000_hw *hw) +{ + s32 ret_val = E1000_SUCCESS; + u16 offset, nvm_data, i; + + DEBUGFUNC("e1000_read_mac_addr"); + + for (i = 0; i < ETH_ADDR_LEN; i += 2) { + offset = i >> 1; + ret_val = hw->nvm.ops.read(hw, offset, 1, &nvm_data); + if (ret_val) { + DEBUGOUT("NVM Read Error\n"); + goto out; + } + hw->mac.perm_addr[i] = (u8)(nvm_data & 0xFF); + hw->mac.perm_addr[i+1] = (u8)(nvm_data >> 8); + } + + /* Flip last bit of mac address if we're on second port */ + if (hw->bus.func == E1000_FUNC_1) + hw->mac.perm_addr[5] ^= 1; + + for (i = 0; i < ETH_ADDR_LEN; i++) + hw->mac.addr[i] = hw->mac.perm_addr[i]; + +out: + return ret_val; +} + +/** + * e1000_validate_nvm_checksum_generic - Validate EEPROM checksum + * @hw: pointer to the HW structure + * + * Calculates the EEPROM checksum by reading/adding each word of the EEPROM + * and then verifies that the sum of the EEPROM is equal to 0xBABA. + **/ +s32 e1000_validate_nvm_checksum_generic(struct e1000_hw *hw) +{ + s32 ret_val = E1000_SUCCESS; + u16 checksum = 0; + u16 i, nvm_data; + + DEBUGFUNC("e1000_validate_nvm_checksum_generic"); + + for (i = 0; i < (NVM_CHECKSUM_REG + 1); i++) { + ret_val = hw->nvm.ops.read(hw, i, 1, &nvm_data); + if (ret_val) { + DEBUGOUT("NVM Read Error\n"); + goto out; + } + checksum += nvm_data; + } + + if (checksum != (u16) NVM_SUM) { + DEBUGOUT("NVM Checksum Invalid\n"); + ret_val = -E1000_ERR_NVM; + goto out; + } + +out: + return ret_val; +} + +/** + * e1000_update_nvm_checksum_generic - Update EEPROM checksum + * @hw: pointer to the HW structure + * + * Updates the EEPROM checksum by reading/adding each word of the EEPROM + * up to the checksum. Then calculates the EEPROM checksum and writes the + * value to the EEPROM. + **/ +s32 e1000_update_nvm_checksum_generic(struct e1000_hw *hw) +{ + s32 ret_val; + u16 checksum = 0; + u16 i, nvm_data; + + DEBUGFUNC("e1000_update_nvm_checksum"); + + for (i = 0; i < NVM_CHECKSUM_REG; i++) { + ret_val = hw->nvm.ops.read(hw, i, 1, &nvm_data); + if (ret_val) { + DEBUGOUT("NVM Read Error while updating checksum.\n"); + goto out; + } + checksum += nvm_data; + } + checksum = (u16) NVM_SUM - checksum; + ret_val = hw->nvm.ops.write(hw, NVM_CHECKSUM_REG, 1, &checksum); + if (ret_val) + DEBUGOUT("NVM Write Error while updating checksum.\n"); + +out: + return ret_val; +} + +/** + * e1000_reload_nvm_generic - Reloads EEPROM + * @hw: pointer to the HW structure + * + * Reloads the EEPROM by setting the "Reinitialize from EEPROM" bit in the + * extended control register. + **/ +void e1000_reload_nvm_generic(struct e1000_hw *hw) +{ + u32 ctrl_ext; + + DEBUGFUNC("e1000_reload_nvm_generic"); + + usec_delay(10); + ctrl_ext = E1000_READ_REG(hw, E1000_CTRL_EXT); + ctrl_ext |= E1000_CTRL_EXT_EE_RST; + E1000_WRITE_REG(hw, E1000_CTRL_EXT, ctrl_ext); + E1000_WRITE_FLUSH(hw); +} + diff --git a/sys/dev/netif/ig_hal/e1000_nvm.h b/sys/dev/netif/ig_hal/e1000_nvm.h new file mode 100644 index 0000000000..d0ab33c614 --- /dev/null +++ b/sys/dev/netif/ig_hal/e1000_nvm.h @@ -0,0 +1,68 @@ +/****************************************************************************** + + Copyright (c) 2001-2008, Intel Corporation + All rights reserved. + + Redistribution and use in source and binary forms, with or without + modification, are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, + this list of conditions and the following disclaimer. + + 2. Redistributions in binary form must reproduce the above copyright + notice, this list of conditions and the following disclaimer in the + documentation and/or other materials provided with the distribution. + + 3. Neither the name of the Intel Corporation nor the names of its + contributors may be used to endorse or promote products derived from + this software without specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE + ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE + LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR + CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF + SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS + INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN + CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) + ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + POSSIBILITY OF SUCH DAMAGE. + +******************************************************************************/ +/*$FreeBSD$*/ + +#ifndef _E1000_NVM_H_ +#define _E1000_NVM_H_ + +void e1000_init_nvm_ops_generic(struct e1000_hw *hw); +s32 e1000_null_read_nvm(struct e1000_hw *hw, u16 a, u16 b, u16 *c); +void e1000_null_nvm_generic(struct e1000_hw *hw); +s32 e1000_null_led_default(struct e1000_hw *hw, u16 *data); +s32 e1000_null_write_nvm(struct e1000_hw *hw, u16 a, u16 b, u16 *c); +s32 e1000_acquire_nvm_generic(struct e1000_hw *hw); + +s32 e1000_poll_eerd_eewr_done(struct e1000_hw *hw, int ee_reg); +s32 e1000_read_mac_addr_generic(struct e1000_hw *hw); +s32 e1000_read_pba_num_generic(struct e1000_hw *hw, u32 *pba_num); +s32 e1000_read_nvm_spi(struct e1000_hw *hw, u16 offset, u16 words, u16 *data); +s32 e1000_read_nvm_microwire(struct e1000_hw *hw, u16 offset, + u16 words, u16 *data); +s32 e1000_read_nvm_eerd(struct e1000_hw *hw, u16 offset, u16 words, + u16 *data); +s32 e1000_valid_led_default_generic(struct e1000_hw *hw, u16 *data); +s32 e1000_validate_nvm_checksum_generic(struct e1000_hw *hw); +s32 e1000_write_nvm_eewr(struct e1000_hw *hw, u16 offset, + u16 words, u16 *data); +s32 e1000_write_nvm_microwire(struct e1000_hw *hw, u16 offset, + u16 words, u16 *data); +s32 e1000_write_nvm_spi(struct e1000_hw *hw, u16 offset, u16 words, + u16 *data); +s32 e1000_update_nvm_checksum_generic(struct e1000_hw *hw); +void e1000_stop_nvm(struct e1000_hw *hw); +void e1000_release_nvm_generic(struct e1000_hw *hw); +void e1000_reload_nvm_generic(struct e1000_hw *hw); + +#define E1000_STM_OPCODE 0xDB00 + +#endif diff --git a/sys/dev/netif/ig_hal/e1000_osdep.c b/sys/dev/netif/ig_hal/e1000_osdep.c new file mode 100644 index 0000000000..fad6a109f0 --- /dev/null +++ b/sys/dev/netif/ig_hal/e1000_osdep.c @@ -0,0 +1,87 @@ +/****************************************************************************** + + Copyright (c) 2001-2008, Intel Corporation + All rights reserved. + + Redistribution and use in source and binary forms, with or without + modification, are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, + this list of conditions and the following disclaimer. + + 2. Redistributions in binary form must reproduce the above copyright + notice, this list of conditions and the following disclaimer in the + documentation and/or other materials provided with the distribution. + + 3. Neither the name of the Intel Corporation nor the names of its + contributors may be used to endorse or promote products derived from + this software without specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE + ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE + LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR + CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF + SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS + INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN + CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) + ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + POSSIBILITY OF SUCH DAMAGE. + +******************************************************************************/ + +#include "e1000_api.h" + +/* + * NOTE: the following routines using the e1000 + * naming style are provided to the shared + * code but are OS specific + */ + +void +e1000_write_pci_cfg(struct e1000_hw *hw, uint32_t reg, uint16_t *value) +{ + pci_write_config(((struct e1000_osdep *)hw->back)->dev, reg, *value, 2); +} + +void +e1000_read_pci_cfg(struct e1000_hw *hw, uint32_t reg, uint16_t *value) +{ + *value = pci_read_config(((struct e1000_osdep *)hw->back)->dev, reg, 2); +} + +void +e1000_pci_set_mwi(struct e1000_hw *hw) +{ + pci_write_config(((struct e1000_osdep *)hw->back)->dev, PCIR_COMMAND, + (hw->bus.pci_cmd_word | CMD_MEM_WRT_INVALIDATE), 2); +} + +void +e1000_pci_clear_mwi(struct e1000_hw *hw) +{ + pci_write_config(((struct e1000_osdep *)hw->back)->dev, PCIR_COMMAND, + (hw->bus.pci_cmd_word & ~CMD_MEM_WRT_INVALIDATE), 2); +} + +/* + * Read the PCI Express capabilities + */ +int32_t +e1000_read_pcie_cap_reg(struct e1000_hw *hw, uint32_t reg, uint16_t *value) +{ + device_t dev = ((struct e1000_osdep *)hw->back)->dev; + uint8_t pcie_ptr; + + pcie_ptr = pci_get_pciecap_ptr(dev); + if (pcie_ptr == 0) + return E1000_NOT_IMPLEMENTED; + + *value = pci_read_config(dev, pcie_ptr + reg, 2); + return E1000_SUCCESS; +} + +/* Module glue */ +static moduledata_t ig_hal_mod = { "ig_hal" }; +DECLARE_MODULE(ig_hal, ig_hal_mod, SI_SUB_DRIVERS, SI_ORDER_MIDDLE); diff --git a/sys/dev/netif/ig_hal/e1000_osdep.h b/sys/dev/netif/ig_hal/e1000_osdep.h new file mode 100644 index 0000000000..c76ea28ba1 --- /dev/null +++ b/sys/dev/netif/ig_hal/e1000_osdep.h @@ -0,0 +1,167 @@ +/****************************************************************************** + + Copyright (c) 2001-2008, Intel Corporation + All rights reserved. + + Redistribution and use in source and binary forms, with or without + modification, are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, + this list of conditions and the following disclaimer. + + 2. Redistributions in binary form must reproduce the above copyright + notice, this list of conditions and the following disclaimer in the + documentation and/or other materials provided with the distribution. + + 3. Neither the name of the Intel Corporation nor the names of its + contributors may be used to endorse or promote products derived from + this software without specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE + ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE + LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR + CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF + SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS + INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN + CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) + ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + POSSIBILITY OF SUCH DAMAGE. + +******************************************************************************/ + +#ifndef _DRAGONFLY_OS_H_ +#define _DRAGONFLY_OS_H_ + +#include +#include +#include +#include + +#include +#include + +#define usec_delay(x) DELAY(x) +#define msec_delay(x) DELAY(1000*(x)) +/* TODO: Should we be paranoid about delaying in interrupt context? */ +#define msec_delay_irq(x) DELAY(1000*(x)) + +#define DEBUGFUNC(F) DEBUGOUT(F) +#define DEBUGOUT(S) +#define DEBUGOUT1(S,A) +#define DEBUGOUT2(S,A,B) +#define DEBUGOUT3(S,A,B,C) +#define DEBUGOUT7(S,A,B,C,D,E,F,G) + +#define CMD_MEM_WRT_INVALIDATE 0x0010 /* BIT_4 */ +#define PCI_COMMAND_REGISTER PCIR_COMMAND + +/* + * These typedefs are necessary due to the new + * shared code, they are native to Linux. + */ +typedef uint64_t u64; +typedef uint32_t u32; +typedef uint16_t u16; +typedef uint8_t u8; +typedef int64_t s64; +typedef int32_t s32; +typedef int16_t s16; +typedef int8_t s8; +typedef boolean_t bool; + +#define __le16 u16 +#define __le32 u32 +#define __le64 u64 + +struct e1000_osdep { + bus_space_tag_t mem_bus_space_tag; + bus_space_handle_t mem_bus_space_handle; + bus_space_tag_t io_bus_space_tag; + bus_space_handle_t io_bus_space_handle; + bus_space_tag_t flash_bus_space_tag; + bus_space_handle_t flash_bus_space_handle; + device_t dev; +}; + +#define E1000_REGISTER(hw, reg) (((hw)->mac.type >= e1000_82543) \ + ? reg : e1000_translate_register_82542(reg)) + +#define E1000_WRITE_FLUSH(a) E1000_READ_REG(a, E1000_STATUS) + +/* Read from an absolute offset in the adapter's memory space */ +#define E1000_READ_OFFSET(hw, offset) \ + bus_space_read_4(((struct e1000_osdep *)(hw)->back)->mem_bus_space_tag, \ + ((struct e1000_osdep *)(hw)->back)->mem_bus_space_handle, offset) + +/* Write to an absolute offset in the adapter's memory space */ +#define E1000_WRITE_OFFSET(hw, offset, value) \ + bus_space_write_4(((struct e1000_osdep *)(hw)->back)->mem_bus_space_tag, \ + ((struct e1000_osdep *)(hw)->back)->mem_bus_space_handle, offset, value) + +/* Register READ/WRITE macros */ + +#define E1000_READ_REG(hw, reg) \ + bus_space_read_4(((struct e1000_osdep *)(hw)->back)->mem_bus_space_tag, \ + ((struct e1000_osdep *)(hw)->back)->mem_bus_space_handle, \ + E1000_REGISTER(hw, reg)) + +#define E1000_WRITE_REG(hw, reg, value) \ + bus_space_write_4(((struct e1000_osdep *)(hw)->back)->mem_bus_space_tag, \ + ((struct e1000_osdep *)(hw)->back)->mem_bus_space_handle, \ + E1000_REGISTER(hw, reg), value) + +#define E1000_READ_REG_ARRAY(hw, reg, index) \ + bus_space_read_4(((struct e1000_osdep *)(hw)->back)->mem_bus_space_tag, \ + ((struct e1000_osdep *)(hw)->back)->mem_bus_space_handle, \ + E1000_REGISTER(hw, reg) + ((index)<< 2)) + +#define E1000_WRITE_REG_ARRAY(hw, reg, index, value) \ + bus_space_write_4(((struct e1000_osdep *)(hw)->back)->mem_bus_space_tag, \ + ((struct e1000_osdep *)(hw)->back)->mem_bus_space_handle, \ + E1000_REGISTER(hw, reg) + ((index)<< 2), value) + +#define E1000_READ_REG_ARRAY_DWORD E1000_READ_REG_ARRAY +#define E1000_WRITE_REG_ARRAY_DWORD E1000_WRITE_REG_ARRAY + +#define E1000_READ_REG_ARRAY_BYTE(hw, reg, index) \ + bus_space_read_1(((struct e1000_osdep *)(hw)->back)->mem_bus_space_tag, \ + ((struct e1000_osdep *)(hw)->back)->mem_bus_space_handle, \ + E1000_REGISTER(hw, reg) + index) + +#define E1000_WRITE_REG_ARRAY_BYTE(hw, reg, index, value) \ + bus_space_write_1(((struct e1000_osdep *)(hw)->back)->mem_bus_space_tag, \ + ((struct e1000_osdep *)(hw)->back)->mem_bus_space_handle, \ + E1000_REGISTER(hw, reg) + index, value) + +#define E1000_WRITE_REG_ARRAY_WORD(hw, reg, index, value) \ + bus_space_write_2(((struct e1000_osdep *)(hw)->back)->mem_bus_space_tag, \ + ((struct e1000_osdep *)(hw)->back)->mem_bus_space_handle, \ + E1000_REGISTER(hw, reg) + (index << 1), value) + +#define E1000_WRITE_REG_IO(hw, reg, value) do {\ + bus_space_write_4(((struct e1000_osdep *)(hw)->back)->io_bus_space_tag, \ + ((struct e1000_osdep *)(hw)->back)->io_bus_space_handle, \ + (hw)->io_base, reg); \ + bus_space_write_4(((struct e1000_osdep *)(hw)->back)->io_bus_space_tag, \ + ((struct e1000_osdep *)(hw)->back)->io_bus_space_handle, \ + (hw)->io_base + 4, value); } while (0) + +#define E1000_READ_FLASH_REG(hw, reg) \ + bus_space_read_4(((struct e1000_osdep *)(hw)->back)->flash_bus_space_tag, \ + ((struct e1000_osdep *)(hw)->back)->flash_bus_space_handle, reg) + +#define E1000_READ_FLASH_REG16(hw, reg) \ + bus_space_read_2(((struct e1000_osdep *)(hw)->back)->flash_bus_space_tag, \ + ((struct e1000_osdep *)(hw)->back)->flash_bus_space_handle, reg) + +#define E1000_WRITE_FLASH_REG(hw, reg, value) \ + bus_space_write_4(((struct e1000_osdep *)(hw)->back)->flash_bus_space_tag, \ + ((struct e1000_osdep *)(hw)->back)->flash_bus_space_handle, reg, value) + +#define E1000_WRITE_FLASH_REG16(hw, reg, value) \ + bus_space_write_2(((struct e1000_osdep *)(hw)->back)->flash_bus_space_tag, \ + ((struct e1000_osdep *)(hw)->back)->flash_bus_space_handle, reg, value) + +#endif /* _DRAGONFLY_OS_H_ */ diff --git a/sys/dev/netif/ig_hal/e1000_phy.c b/sys/dev/netif/ig_hal/e1000_phy.c new file mode 100644 index 0000000000..2e4d0462eb --- /dev/null +++ b/sys/dev/netif/ig_hal/e1000_phy.c @@ -0,0 +1,2554 @@ +/****************************************************************************** + + Copyright (c) 2001-2008, Intel Corporation + All rights reserved. + + Redistribution and use in source and binary forms, with or without + modification, are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, + this list of conditions and the following disclaimer. + + 2. Redistributions in binary form must reproduce the above copyright + notice, this list of conditions and the following disclaimer in the + documentation and/or other materials provided with the distribution. + + 3. Neither the name of the Intel Corporation nor the names of its + contributors may be used to endorse or promote products derived from + this software without specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE + ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE + LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR + CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF + SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS + INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN + CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) + ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + POSSIBILITY OF SUCH DAMAGE. + +******************************************************************************/ +/*$FreeBSD$*/ + +#include "e1000_api.h" + +static u32 e1000_get_phy_addr_for_bm_page(u32 page, u32 reg); +static s32 e1000_access_phy_wakeup_reg_bm(struct e1000_hw *hw, u32 offset, + u16 *data, bool read); +/* Cable length tables */ +static const u16 e1000_m88_cable_length_table[] = + { 0, 50, 80, 110, 140, 140, E1000_CABLE_LENGTH_UNDEFINED }; +#define M88E1000_CABLE_LENGTH_TABLE_SIZE \ + (sizeof(e1000_m88_cable_length_table) / \ + sizeof(e1000_m88_cable_length_table[0])) + +static const u16 e1000_igp_2_cable_length_table[] = + { 0, 0, 0, 0, 0, 0, 0, 0, 3, 5, 8, 11, 13, 16, 18, 21, + 0, 0, 0, 3, 6, 10, 13, 16, 19, 23, 26, 29, 32, 35, 38, 41, + 6, 10, 14, 18, 22, 26, 30, 33, 37, 41, 44, 48, 51, 54, 58, 61, + 21, 26, 31, 35, 40, 44, 49, 53, 57, 61, 65, 68, 72, 75, 79, 82, + 40, 45, 51, 56, 61, 66, 70, 75, 79, 83, 87, 91, 94, 98, 101, 104, + 60, 66, 72, 77, 82, 87, 92, 96, 100, 104, 108, 111, 114, 117, 119, 121, + 83, 89, 95, 100, 105, 109, 113, 116, 119, 122, 124, + 104, 109, 114, 118, 121, 124}; +#define IGP02E1000_CABLE_LENGTH_TABLE_SIZE \ + (sizeof(e1000_igp_2_cable_length_table) / \ + sizeof(e1000_igp_2_cable_length_table[0])) + +/** + * e1000_init_phy_ops_generic - Initialize PHY function pointers + * @hw: pointer to the HW structure + * + * Setups up the function pointers to no-op functions + **/ +void e1000_init_phy_ops_generic(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + DEBUGFUNC("e1000_init_phy_ops_generic"); + + /* Initialize function pointers */ + phy->ops.init_params = e1000_null_ops_generic; + phy->ops.acquire = e1000_null_ops_generic; + phy->ops.check_polarity = e1000_null_ops_generic; + phy->ops.check_reset_block = e1000_null_ops_generic; + phy->ops.commit = e1000_null_ops_generic; + phy->ops.force_speed_duplex = e1000_null_ops_generic; + phy->ops.get_cfg_done = e1000_null_ops_generic; + phy->ops.get_cable_length = e1000_null_ops_generic; + phy->ops.get_info = e1000_null_ops_generic; + phy->ops.read_reg = e1000_null_read_reg; + phy->ops.release = e1000_null_phy_generic; + phy->ops.reset = e1000_null_ops_generic; + phy->ops.set_d0_lplu_state = e1000_null_lplu_state; + phy->ops.set_d3_lplu_state = e1000_null_lplu_state; + phy->ops.write_reg = e1000_null_write_reg; + phy->ops.power_up = e1000_null_phy_generic; + phy->ops.power_down = e1000_null_phy_generic; + phy->ops.cfg_on_link_up = e1000_null_ops_generic; +} + +/** + * e1000_null_read_reg - No-op function, return 0 + * @hw: pointer to the HW structure + **/ +s32 e1000_null_read_reg(struct e1000_hw *hw, u32 offset, u16 *data) +{ + DEBUGFUNC("e1000_null_read_reg"); + return E1000_SUCCESS; +} + +/** + * e1000_null_phy_generic - No-op function, return void + * @hw: pointer to the HW structure + **/ +void e1000_null_phy_generic(struct e1000_hw *hw) +{ + DEBUGFUNC("e1000_null_phy_generic"); + return; +} + +/** + * e1000_null_lplu_state - No-op function, return 0 + * @hw: pointer to the HW structure + **/ +s32 e1000_null_lplu_state(struct e1000_hw *hw, bool active) +{ + DEBUGFUNC("e1000_null_lplu_state"); + return E1000_SUCCESS; +} + +/** + * e1000_null_write_reg - No-op function, return 0 + * @hw: pointer to the HW structure + **/ +s32 e1000_null_write_reg(struct e1000_hw *hw, u32 offset, u16 data) +{ + DEBUGFUNC("e1000_null_write_reg"); + return E1000_SUCCESS; +} + +/** + * e1000_check_reset_block_generic - Check if PHY reset is blocked + * @hw: pointer to the HW structure + * + * Read the PHY management control register and check whether a PHY reset + * is blocked. If a reset is not blocked return E1000_SUCCESS, otherwise + * return E1000_BLK_PHY_RESET (12). + **/ +s32 e1000_check_reset_block_generic(struct e1000_hw *hw) +{ + u32 manc; + + DEBUGFUNC("e1000_check_reset_block"); + + manc = E1000_READ_REG(hw, E1000_MANC); + + return (manc & E1000_MANC_BLK_PHY_RST_ON_IDE) ? + E1000_BLK_PHY_RESET : E1000_SUCCESS; +} + +/** + * e1000_get_phy_id - Retrieve the PHY ID and revision + * @hw: pointer to the HW structure + * + * Reads the PHY registers and stores the PHY ID and possibly the PHY + * revision in the hardware structure. + **/ +s32 e1000_get_phy_id(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val = E1000_SUCCESS; + u16 phy_id; + + DEBUGFUNC("e1000_get_phy_id"); + + if (!(phy->ops.read_reg)) + goto out; + + ret_val = phy->ops.read_reg(hw, PHY_ID1, &phy_id); + if (ret_val) + goto out; + + phy->id = (u32)(phy_id << 16); + usec_delay(20); + ret_val = phy->ops.read_reg(hw, PHY_ID2, &phy_id); + if (ret_val) + goto out; + + phy->id |= (u32)(phy_id & PHY_REVISION_MASK); + phy->revision = (u32)(phy_id & ~PHY_REVISION_MASK); + +out: + return ret_val; +} + +/** + * e1000_phy_reset_dsp_generic - Reset PHY DSP + * @hw: pointer to the HW structure + * + * Reset the digital signal processor. + **/ +s32 e1000_phy_reset_dsp_generic(struct e1000_hw *hw) +{ + s32 ret_val = E1000_SUCCESS; + + DEBUGFUNC("e1000_phy_reset_dsp_generic"); + + if (!(hw->phy.ops.write_reg)) + goto out; + + ret_val = hw->phy.ops.write_reg(hw, M88E1000_PHY_GEN_CONTROL, 0xC1); + if (ret_val) + goto out; + + ret_val = hw->phy.ops.write_reg(hw, M88E1000_PHY_GEN_CONTROL, 0); + +out: + return ret_val; +} + +/** + * e1000_read_phy_reg_mdic - Read MDI control register + * @hw: pointer to the HW structure + * @offset: register offset to be read + * @data: pointer to the read data + * + * Reads the MDI control register in the PHY at offset and stores the + * information read to data. + **/ +s32 e1000_read_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 *data) +{ + struct e1000_phy_info *phy = &hw->phy; + u32 i, mdic = 0; + s32 ret_val = E1000_SUCCESS; + + DEBUGFUNC("e1000_read_phy_reg_mdic"); + + /* + * Set up Op-code, Phy Address, and register offset in the MDI + * Control register. The MAC will take care of interfacing with the + * PHY to retrieve the desired data. + */ + mdic = ((offset << E1000_MDIC_REG_SHIFT) | + (phy->addr << E1000_MDIC_PHY_SHIFT) | + (E1000_MDIC_OP_READ)); + + E1000_WRITE_REG(hw, E1000_MDIC, mdic); + + /* + * Poll the ready bit to see if the MDI read completed + * Increasing the time out as testing showed failures with + * the lower time out + */ + for (i = 0; i < (E1000_GEN_POLL_TIMEOUT * 3); i++) { + usec_delay(50); + mdic = E1000_READ_REG(hw, E1000_MDIC); + if (mdic & E1000_MDIC_READY) + break; + } + if (!(mdic & E1000_MDIC_READY)) { + DEBUGOUT("MDI Read did not complete\n"); + ret_val = -E1000_ERR_PHY; + goto out; + } + if (mdic & E1000_MDIC_ERROR) { + DEBUGOUT("MDI Error\n"); + ret_val = -E1000_ERR_PHY; + goto out; + } + *data = (u16) mdic; + +out: + return ret_val; +} + +/** + * e1000_write_phy_reg_mdic - Write MDI control register + * @hw: pointer to the HW structure + * @offset: register offset to write to + * @data: data to write to register at offset + * + * Writes data to MDI control register in the PHY at offset. + **/ +s32 e1000_write_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 data) +{ + struct e1000_phy_info *phy = &hw->phy; + u32 i, mdic = 0; + s32 ret_val = E1000_SUCCESS; + + DEBUGFUNC("e1000_write_phy_reg_mdic"); + + /* + * Set up Op-code, Phy Address, and register offset in the MDI + * Control register. The MAC will take care of interfacing with the + * PHY to retrieve the desired data. + */ + mdic = (((u32)data) | + (offset << E1000_MDIC_REG_SHIFT) | + (phy->addr << E1000_MDIC_PHY_SHIFT) | + (E1000_MDIC_OP_WRITE)); + + E1000_WRITE_REG(hw, E1000_MDIC, mdic); + + /* + * Poll the ready bit to see if the MDI read completed + * Increasing the time out as testing showed failures with + * the lower time out + */ + for (i = 0; i < (E1000_GEN_POLL_TIMEOUT * 3); i++) { + usec_delay(50); + mdic = E1000_READ_REG(hw, E1000_MDIC); + if (mdic & E1000_MDIC_READY) + break; + } + if (!(mdic & E1000_MDIC_READY)) { + DEBUGOUT("MDI Write did not complete\n"); + ret_val = -E1000_ERR_PHY; + goto out; + } + if (mdic & E1000_MDIC_ERROR) { + DEBUGOUT("MDI Error\n"); + ret_val = -E1000_ERR_PHY; + goto out; + } + +out: + return ret_val; +} + +/** + * e1000_read_phy_reg_m88 - Read m88 PHY register + * @hw: pointer to the HW structure + * @offset: register offset to be read + * @data: pointer to the read data + * + * Acquires semaphore, if necessary, then reads the PHY register at offset + * and storing the retrieved information in data. Release any acquired + * semaphores before exiting. + **/ +s32 e1000_read_phy_reg_m88(struct e1000_hw *hw, u32 offset, u16 *data) +{ + s32 ret_val = E1000_SUCCESS; + + DEBUGFUNC("e1000_read_phy_reg_m88"); + + if (!(hw->phy.ops.acquire)) + goto out; + + ret_val = hw->phy.ops.acquire(hw); + if (ret_val) + goto out; + + ret_val = e1000_read_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & offset, + data); + + hw->phy.ops.release(hw); + +out: + return ret_val; +} + +/** + * e1000_write_phy_reg_m88 - Write m88 PHY register + * @hw: pointer to the HW structure + * @offset: register offset to write to + * @data: data to write at register offset + * + * Acquires semaphore, if necessary, then writes the data to PHY register + * at the offset. Release any acquired semaphores before exiting. + **/ +s32 e1000_write_phy_reg_m88(struct e1000_hw *hw, u32 offset, u16 data) +{ + s32 ret_val = E1000_SUCCESS; + + DEBUGFUNC("e1000_write_phy_reg_m88"); + + if (!(hw->phy.ops.acquire)) + goto out; + + ret_val = hw->phy.ops.acquire(hw); + if (ret_val) + goto out; + + ret_val = e1000_write_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & offset, + data); + + hw->phy.ops.release(hw); + +out: + return ret_val; +} + +/** + * e1000_read_phy_reg_igp - Read igp PHY register + * @hw: pointer to the HW structure + * @offset: register offset to be read + * @data: pointer to the read data + * + * Acquires semaphore, if necessary, then reads the PHY register at offset + * and storing the retrieved information in data. Release any acquired + * semaphores before exiting. + **/ +s32 e1000_read_phy_reg_igp(struct e1000_hw *hw, u32 offset, u16 *data) +{ + s32 ret_val = E1000_SUCCESS; + + DEBUGFUNC("e1000_read_phy_reg_igp"); + + if (!(hw->phy.ops.acquire)) + goto out; + + ret_val = hw->phy.ops.acquire(hw); + if (ret_val) + goto out; + + if (offset > MAX_PHY_MULTI_PAGE_REG) { + ret_val = e1000_write_phy_reg_mdic(hw, + IGP01E1000_PHY_PAGE_SELECT, + (u16)offset); + if (ret_val) { + hw->phy.ops.release(hw); + goto out; + } + } + + ret_val = e1000_read_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & offset, + data); + + hw->phy.ops.release(hw); + +out: + return ret_val; +} + +/** + * e1000_write_phy_reg_igp - Write igp PHY register + * @hw: pointer to the HW structure + * @offset: register offset to write to + * @data: data to write at register offset + * + * Acquires semaphore, if necessary, then writes the data to PHY register + * at the offset. Release any acquired semaphores before exiting. + **/ +s32 e1000_write_phy_reg_igp(struct e1000_hw *hw, u32 offset, u16 data) +{ + s32 ret_val = E1000_SUCCESS; + + DEBUGFUNC("e1000_write_phy_reg_igp"); + + if (!(hw->phy.ops.acquire)) + goto out; + + ret_val = hw->phy.ops.acquire(hw); + if (ret_val) + goto out; + + if (offset > MAX_PHY_MULTI_PAGE_REG) { + ret_val = e1000_write_phy_reg_mdic(hw, + IGP01E1000_PHY_PAGE_SELECT, + (u16)offset); + if (ret_val) { + hw->phy.ops.release(hw); + goto out; + } + } + + ret_val = e1000_write_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & offset, + data); + + hw->phy.ops.release(hw); + +out: + return ret_val; +} + +/** + * e1000_read_kmrn_reg_generic - Read kumeran register + * @hw: pointer to the HW structure + * @offset: register offset to be read + * @data: pointer to the read data + * + * Acquires semaphore, if necessary. Then reads the PHY register at offset + * using the kumeran interface. The information retrieved is stored in data. + * Release any acquired semaphores before exiting. + **/ +s32 e1000_read_kmrn_reg_generic(struct e1000_hw *hw, u32 offset, u16 *data) +{ + u32 kmrnctrlsta; + s32 ret_val = E1000_SUCCESS; + + DEBUGFUNC("e1000_read_kmrn_reg_generic"); + + if (!(hw->phy.ops.acquire)) + goto out; + + ret_val = hw->phy.ops.acquire(hw); + if (ret_val) + goto out; + + kmrnctrlsta = ((offset << E1000_KMRNCTRLSTA_OFFSET_SHIFT) & + E1000_KMRNCTRLSTA_OFFSET) | E1000_KMRNCTRLSTA_REN; + E1000_WRITE_REG(hw, E1000_KMRNCTRLSTA, kmrnctrlsta); + + usec_delay(2); + + kmrnctrlsta = E1000_READ_REG(hw, E1000_KMRNCTRLSTA); + *data = (u16)kmrnctrlsta; + + hw->phy.ops.release(hw); + +out: + return ret_val; +} + +/** + * e1000_write_kmrn_reg_generic - Write kumeran register + * @hw: pointer to the HW structure + * @offset: register offset to write to + * @data: data to write at register offset + * + * Acquires semaphore, if necessary. Then write the data to PHY register + * at the offset using the kumeran interface. Release any acquired semaphores + * before exiting. + **/ +s32 e1000_write_kmrn_reg_generic(struct e1000_hw *hw, u32 offset, u16 data) +{ + u32 kmrnctrlsta; + s32 ret_val = E1000_SUCCESS; + + DEBUGFUNC("e1000_write_kmrn_reg_generic"); + + if (!(hw->phy.ops.acquire)) + goto out; + + ret_val = hw->phy.ops.acquire(hw); + if (ret_val) + goto out; + + kmrnctrlsta = ((offset << E1000_KMRNCTRLSTA_OFFSET_SHIFT) & + E1000_KMRNCTRLSTA_OFFSET) | data; + E1000_WRITE_REG(hw, E1000_KMRNCTRLSTA, kmrnctrlsta); + + usec_delay(2); + hw->phy.ops.release(hw); + +out: + return ret_val; +} + +/** + * e1000_copper_link_setup_m88 - Setup m88 PHY's for copper link + * @hw: pointer to the HW structure + * + * Sets up MDI/MDI-X and polarity for m88 PHY's. If necessary, transmit clock + * and downshift values are set also. + **/ +s32 e1000_copper_link_setup_m88(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val; + u16 phy_data; + + DEBUGFUNC("e1000_copper_link_setup_m88"); + + if (phy->reset_disable) { + ret_val = E1000_SUCCESS; + goto out; + } + + /* Enable CRS on TX. This must be set for half-duplex operation. */ + ret_val = phy->ops.read_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data); + if (ret_val) + goto out; + + /* For newer PHYs this bit is downshift enable */ + if (phy->type == e1000_phy_m88) + phy_data |= M88E1000_PSCR_ASSERT_CRS_ON_TX; + + /* + * Options: + * MDI/MDI-X = 0 (default) + * 0 - Auto for all speeds + * 1 - MDI mode + * 2 - MDI-X mode + * 3 - Auto for 1000Base-T only (MDI-X for 10/100Base-T modes) + */ + phy_data &= ~M88E1000_PSCR_AUTO_X_MODE; + + switch (phy->mdix) { + case 1: + phy_data |= M88E1000_PSCR_MDI_MANUAL_MODE; + break; + case 2: + phy_data |= M88E1000_PSCR_MDIX_MANUAL_MODE; + break; + case 3: + phy_data |= M88E1000_PSCR_AUTO_X_1000T; + break; + case 0: + default: + phy_data |= M88E1000_PSCR_AUTO_X_MODE; + break; + } + + /* + * Options: + * disable_polarity_correction = 0 (default) + * Automatic Correction for Reversed Cable Polarity + * 0 - Disabled + * 1 - Enabled + */ + phy_data &= ~M88E1000_PSCR_POLARITY_REVERSAL; + if (phy->disable_polarity_correction == 1) + phy_data |= M88E1000_PSCR_POLARITY_REVERSAL; + + /* Enable downshift on BM (disabled by default) */ + if (phy->type == e1000_phy_bm) + phy_data |= BME1000_PSCR_ENABLE_DOWNSHIFT; + + ret_val = phy->ops.write_reg(hw, M88E1000_PHY_SPEC_CTRL, phy_data); + if (ret_val) + goto out; + + if ((phy->type == e1000_phy_m88) && + (phy->revision < E1000_REVISION_4) && + (phy->id != BME1000_E_PHY_ID_R2)) { + /* + * Force TX_CLK in the Extended PHY Specific Control Register + * to 25MHz clock. + */ + ret_val = phy->ops.read_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL, + &phy_data); + if (ret_val) + goto out; + + phy_data |= M88E1000_EPSCR_TX_CLK_25; + + if ((phy->revision == E1000_REVISION_2) && + (phy->id == M88E1111_I_PHY_ID)) { + /* 82573L PHY - set the downshift counter to 5x. */ + phy_data &= ~M88EC018_EPSCR_DOWNSHIFT_COUNTER_MASK; + phy_data |= M88EC018_EPSCR_DOWNSHIFT_COUNTER_5X; + } else { + /* Configure Master and Slave downshift values */ + phy_data &= ~(M88E1000_EPSCR_MASTER_DOWNSHIFT_MASK | + M88E1000_EPSCR_SLAVE_DOWNSHIFT_MASK); + phy_data |= (M88E1000_EPSCR_MASTER_DOWNSHIFT_1X | + M88E1000_EPSCR_SLAVE_DOWNSHIFT_1X); + } + ret_val = phy->ops.write_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL, + phy_data); + if (ret_val) + goto out; + } + + if ((phy->type == e1000_phy_bm) && (phy->id == BME1000_E_PHY_ID_R2)) { + /* Set PHY page 0, register 29 to 0x0003 */ + ret_val = phy->ops.write_reg(hw, 29, 0x0003); + if (ret_val) + goto out; + + /* Set PHY page 0, register 30 to 0x0000 */ + ret_val = phy->ops.write_reg(hw, 30, 0x0000); + if (ret_val) + goto out; + } + + /* Commit the changes. */ + ret_val = phy->ops.commit(hw); + if (ret_val) { + DEBUGOUT("Error committing the PHY changes\n"); + goto out; + } + +out: + return ret_val; +} + +/** + * e1000_copper_link_setup_igp - Setup igp PHY's for copper link + * @hw: pointer to the HW structure + * + * Sets up LPLU, MDI/MDI-X, polarity, Smartspeed and Master/Slave config for + * igp PHY's. + **/ +s32 e1000_copper_link_setup_igp(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val; + u16 data; + + DEBUGFUNC("e1000_copper_link_setup_igp"); + + if (phy->reset_disable) { + ret_val = E1000_SUCCESS; + goto out; + } + + ret_val = hw->phy.ops.reset(hw); + if (ret_val) { + DEBUGOUT("Error resetting the PHY.\n"); + goto out; + } + + /* + * Wait 100ms for MAC to configure PHY from NVM settings, to avoid + * timeout issues when LFS is enabled. + */ + msec_delay(100); + + /* + * The NVM settings will configure LPLU in D3 for + * non-IGP1 PHYs. + */ + if (phy->type == e1000_phy_igp) { + /* disable lplu d3 during driver init */ + ret_val = hw->phy.ops.set_d3_lplu_state(hw, FALSE); + if (ret_val) { + DEBUGOUT("Error Disabling LPLU D3\n"); + goto out; + } + } + + /* disable lplu d0 during driver init */ + if (hw->phy.ops.set_d0_lplu_state) { + ret_val = hw->phy.ops.set_d0_lplu_state(hw, FALSE); + if (ret_val) { + DEBUGOUT("Error Disabling LPLU D0\n"); + goto out; + } + } + /* Configure mdi-mdix settings */ + ret_val = phy->ops.read_reg(hw, IGP01E1000_PHY_PORT_CTRL, &data); + if (ret_val) + goto out; + + data &= ~IGP01E1000_PSCR_AUTO_MDIX; + + switch (phy->mdix) { + case 1: + data &= ~IGP01E1000_PSCR_FORCE_MDI_MDIX; + break; + case 2: + data |= IGP01E1000_PSCR_FORCE_MDI_MDIX; + break; + case 0: + default: + data |= IGP01E1000_PSCR_AUTO_MDIX; + break; + } + ret_val = phy->ops.write_reg(hw, IGP01E1000_PHY_PORT_CTRL, data); + if (ret_val) + goto out; + + /* set auto-master slave resolution settings */ + if (hw->mac.autoneg) { + /* + * when autonegotiation advertisement is only 1000Mbps then we + * should disable SmartSpeed and enable Auto MasterSlave + * resolution as hardware default. + */ + if (phy->autoneg_advertised == ADVERTISE_1000_FULL) { + /* Disable SmartSpeed */ + ret_val = phy->ops.read_reg(hw, + IGP01E1000_PHY_PORT_CONFIG, + &data); + if (ret_val) + goto out; + + data &= ~IGP01E1000_PSCFR_SMART_SPEED; + ret_val = phy->ops.write_reg(hw, + IGP01E1000_PHY_PORT_CONFIG, + data); + if (ret_val) + goto out; + + /* Set auto Master/Slave resolution process */ + ret_val = phy->ops.read_reg(hw, PHY_1000T_CTRL, &data); + if (ret_val) + goto out; + + data &= ~CR_1000T_MS_ENABLE; + ret_val = phy->ops.write_reg(hw, PHY_1000T_CTRL, data); + if (ret_val) + goto out; + } + + ret_val = phy->ops.read_reg(hw, PHY_1000T_CTRL, &data); + if (ret_val) + goto out; + + /* load defaults for future use */ + phy->original_ms_type = (data & CR_1000T_MS_ENABLE) ? + ((data & CR_1000T_MS_VALUE) ? + e1000_ms_force_master : + e1000_ms_force_slave) : + e1000_ms_auto; + + switch (phy->ms_type) { + case e1000_ms_force_master: + data |= (CR_1000T_MS_ENABLE | CR_1000T_MS_VALUE); + break; + case e1000_ms_force_slave: + data |= CR_1000T_MS_ENABLE; + data &= ~(CR_1000T_MS_VALUE); + break; + case e1000_ms_auto: + data &= ~CR_1000T_MS_ENABLE; + default: + break; + } + ret_val = phy->ops.write_reg(hw, PHY_1000T_CTRL, data); + if (ret_val) + goto out; + } + +out: + return ret_val; +} + +/** + * e1000_copper_link_autoneg - Setup/Enable autoneg for copper link + * @hw: pointer to the HW structure + * + * Performs initial bounds checking on autoneg advertisement parameter, then + * configure to advertise the full capability. Setup the PHY to autoneg + * and restart the negotiation process between the link partner. If + * autoneg_wait_to_complete, then wait for autoneg to complete before exiting. + **/ +s32 e1000_copper_link_autoneg(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val; + u16 phy_ctrl; + + DEBUGFUNC("e1000_copper_link_autoneg"); + + /* + * Perform some bounds checking on the autoneg advertisement + * parameter. + */ + phy->autoneg_advertised &= phy->autoneg_mask; + + /* + * If autoneg_advertised is zero, we assume it was not defaulted + * by the calling code so we set to advertise full capability. + */ + if (phy->autoneg_advertised == 0) + phy->autoneg_advertised = phy->autoneg_mask; + + DEBUGOUT("Reconfiguring auto-neg advertisement params\n"); + ret_val = e1000_phy_setup_autoneg(hw); + if (ret_val) { + DEBUGOUT("Error Setting up Auto-Negotiation\n"); + goto out; + } + DEBUGOUT("Restarting Auto-Neg\n"); + + /* + * Restart auto-negotiation by setting the Auto Neg Enable bit and + * the Auto Neg Restart bit in the PHY control register. + */ + ret_val = phy->ops.read_reg(hw, PHY_CONTROL, &phy_ctrl); + if (ret_val) + goto out; + + phy_ctrl |= (MII_CR_AUTO_NEG_EN | MII_CR_RESTART_AUTO_NEG); + ret_val = phy->ops.write_reg(hw, PHY_CONTROL, phy_ctrl); + if (ret_val) + goto out; + + /* + * Does the user want to wait for Auto-Neg to complete here, or + * check at a later time (for example, callback routine). + */ + if (phy->autoneg_wait_to_complete) { + ret_val = hw->mac.ops.wait_autoneg(hw); + if (ret_val) { + DEBUGOUT("Error while waiting for " + "autoneg to complete\n"); + goto out; + } + } + + hw->mac.get_link_status = TRUE; + +out: + return ret_val; +} + +/** + * e1000_phy_setup_autoneg - Configure PHY for auto-negotiation + * @hw: pointer to the HW structure + * + * Reads the MII auto-neg advertisement register and/or the 1000T control + * register and if the PHY is already setup for auto-negotiation, then + * return successful. Otherwise, setup advertisement and flow control to + * the appropriate values for the wanted auto-negotiation. + **/ +s32 e1000_phy_setup_autoneg(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val; + u16 mii_autoneg_adv_reg; + u16 mii_1000t_ctrl_reg = 0; + + DEBUGFUNC("e1000_phy_setup_autoneg"); + + phy->autoneg_advertised &= phy->autoneg_mask; + + /* Read the MII Auto-Neg Advertisement Register (Address 4). */ + ret_val = phy->ops.read_reg(hw, PHY_AUTONEG_ADV, &mii_autoneg_adv_reg); + if (ret_val) + goto out; + + if (phy->autoneg_mask & ADVERTISE_1000_FULL) { + /* Read the MII 1000Base-T Control Register (Address 9). */ + ret_val = phy->ops.read_reg(hw, PHY_1000T_CTRL, + &mii_1000t_ctrl_reg); + if (ret_val) + goto out; + } + + /* + * Need to parse both autoneg_advertised and fc and set up + * the appropriate PHY registers. First we will parse for + * autoneg_advertised software override. Since we can advertise + * a plethora of combinations, we need to check each bit + * individually. + */ + + /* + * First we clear all the 10/100 mb speed bits in the Auto-Neg + * Advertisement Register (Address 4) and the 1000 mb speed bits in + * the 1000Base-T Control Register (Address 9). + */ + mii_autoneg_adv_reg &= ~(NWAY_AR_100TX_FD_CAPS | + NWAY_AR_100TX_HD_CAPS | + NWAY_AR_10T_FD_CAPS | + NWAY_AR_10T_HD_CAPS); + mii_1000t_ctrl_reg &= ~(CR_1000T_HD_CAPS | CR_1000T_FD_CAPS); + + DEBUGOUT1("autoneg_advertised %x\n", phy->autoneg_advertised); + + /* Do we want to advertise 10 Mb Half Duplex? */ + if (phy->autoneg_advertised & ADVERTISE_10_HALF) { + DEBUGOUT("Advertise 10mb Half duplex\n"); + mii_autoneg_adv_reg |= NWAY_AR_10T_HD_CAPS; + } + + /* Do we want to advertise 10 Mb Full Duplex? */ + if (phy->autoneg_advertised & ADVERTISE_10_FULL) { + DEBUGOUT("Advertise 10mb Full duplex\n"); + mii_autoneg_adv_reg |= NWAY_AR_10T_FD_CAPS; + } + + /* Do we want to advertise 100 Mb Half Duplex? */ + if (phy->autoneg_advertised & ADVERTISE_100_HALF) { + DEBUGOUT("Advertise 100mb Half duplex\n"); + mii_autoneg_adv_reg |= NWAY_AR_100TX_HD_CAPS; + } + + /* Do we want to advertise 100 Mb Full Duplex? */ + if (phy->autoneg_advertised & ADVERTISE_100_FULL) { + DEBUGOUT("Advertise 100mb Full duplex\n"); + mii_autoneg_adv_reg |= NWAY_AR_100TX_FD_CAPS; + } + + /* We do not allow the Phy to advertise 1000 Mb Half Duplex */ + if (phy->autoneg_advertised & ADVERTISE_1000_HALF) + DEBUGOUT("Advertise 1000mb Half duplex request denied!\n"); + + /* Do we want to advertise 1000 Mb Full Duplex? */ + if (phy->autoneg_advertised & ADVERTISE_1000_FULL) { + DEBUGOUT("Advertise 1000mb Full duplex\n"); + mii_1000t_ctrl_reg |= CR_1000T_FD_CAPS; + } + + /* + * Check for a software override of the flow control settings, and + * setup the PHY advertisement registers accordingly. If + * auto-negotiation is enabled, then software will have to set the + * "PAUSE" bits to the correct value in the Auto-Negotiation + * Advertisement Register (PHY_AUTONEG_ADV) and re-start auto- + * negotiation. + * + * The possible values of the "fc" parameter are: + * 0: Flow control is completely disabled + * 1: Rx flow control is enabled (we can receive pause frames + * but not send pause frames). + * 2: Tx flow control is enabled (we can send pause frames + * but we do not support receiving pause frames). + * 3: Both Rx and Tx flow control (symmetric) are enabled. + * other: No software override. The flow control configuration + * in the EEPROM is used. + */ + switch (hw->fc.current_mode) { + case e1000_fc_none: + /* + * Flow control (Rx & Tx) is completely disabled by a + * software over-ride. + */ + mii_autoneg_adv_reg &= ~(NWAY_AR_ASM_DIR | NWAY_AR_PAUSE); + break; + case e1000_fc_rx_pause: + /* + * Rx Flow control is enabled, and Tx Flow control is + * disabled, by a software over-ride. + * + * Since there really isn't a way to advertise that we are + * capable of Rx Pause ONLY, we will advertise that we + * support both symmetric and asymmetric Rx PAUSE. Later + * (in e1000_config_fc_after_link_up) we will disable the + * hw's ability to send PAUSE frames. + */ + mii_autoneg_adv_reg |= (NWAY_AR_ASM_DIR | NWAY_AR_PAUSE); + break; + case e1000_fc_tx_pause: + /* + * Tx Flow control is enabled, and Rx Flow control is + * disabled, by a software over-ride. + */ + mii_autoneg_adv_reg |= NWAY_AR_ASM_DIR; + mii_autoneg_adv_reg &= ~NWAY_AR_PAUSE; + break; + case e1000_fc_full: + /* + * Flow control (both Rx and Tx) is enabled by a software + * over-ride. + */ + mii_autoneg_adv_reg |= (NWAY_AR_ASM_DIR | NWAY_AR_PAUSE); + break; + default: + DEBUGOUT("Flow control param set incorrectly\n"); + ret_val = -E1000_ERR_CONFIG; + goto out; + } + + ret_val = phy->ops.write_reg(hw, PHY_AUTONEG_ADV, mii_autoneg_adv_reg); + if (ret_val) + goto out; + + DEBUGOUT1("Auto-Neg Advertising %x\n", mii_autoneg_adv_reg); + + if (phy->autoneg_mask & ADVERTISE_1000_FULL) { + ret_val = phy->ops.write_reg(hw, + PHY_1000T_CTRL, + mii_1000t_ctrl_reg); + if (ret_val) + goto out; + } + +out: + return ret_val; +} + +/** + * e1000_setup_copper_link_generic - Configure copper link settings + * @hw: pointer to the HW structure + * + * Calls the appropriate function to configure the link for auto-neg or forced + * speed and duplex. Then we check for link, once link is established calls + * to configure collision distance and flow control are called. If link is + * not established, we return -E1000_ERR_PHY (-2). + **/ +s32 e1000_setup_copper_link_generic(struct e1000_hw *hw) +{ + s32 ret_val; + bool link; + + DEBUGFUNC("e1000_setup_copper_link_generic"); + + if (hw->mac.autoneg) { + /* + * Setup autoneg and flow control advertisement and perform + * autonegotiation. + */ + ret_val = e1000_copper_link_autoneg(hw); + if (ret_val) + goto out; + } else { + /* + * PHY will be set to 10H, 10F, 100H or 100F + * depending on user settings. + */ + DEBUGOUT("Forcing Speed and Duplex\n"); + ret_val = hw->phy.ops.force_speed_duplex(hw); + if (ret_val) { + DEBUGOUT("Error Forcing Speed and Duplex\n"); + goto out; + } + } + + /* + * Check link status. Wait up to 100 microseconds for link to become + * valid. + */ + ret_val = e1000_phy_has_link_generic(hw, + COPPER_LINK_UP_LIMIT, + 10, + &link); + if (ret_val) + goto out; + + if (link) { + DEBUGOUT("Valid link established!!!\n"); + e1000_config_collision_dist_generic(hw); + ret_val = e1000_config_fc_after_link_up_generic(hw); + } else { + DEBUGOUT("Unable to establish link!!!\n"); + } + +out: + return ret_val; +} + +/** + * e1000_phy_force_speed_duplex_igp - Force speed/duplex for igp PHY + * @hw: pointer to the HW structure + * + * Calls the PHY setup function to force speed and duplex. Clears the + * auto-crossover to force MDI manually. Waits for link and returns + * successful if link up is successful, else -E1000_ERR_PHY (-2). + **/ +s32 e1000_phy_force_speed_duplex_igp(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val; + u16 phy_data; + bool link; + + DEBUGFUNC("e1000_phy_force_speed_duplex_igp"); + + ret_val = phy->ops.read_reg(hw, PHY_CONTROL, &phy_data); + if (ret_val) + goto out; + + e1000_phy_force_speed_duplex_setup(hw, &phy_data); + + ret_val = phy->ops.write_reg(hw, PHY_CONTROL, phy_data); + if (ret_val) + goto out; + + /* + * Clear Auto-Crossover to force MDI manually. IGP requires MDI + * forced whenever speed and duplex are forced. + */ + ret_val = phy->ops.read_reg(hw, IGP01E1000_PHY_PORT_CTRL, &phy_data); + if (ret_val) + goto out; + + phy_data &= ~IGP01E1000_PSCR_AUTO_MDIX; + phy_data &= ~IGP01E1000_PSCR_FORCE_MDI_MDIX; + + ret_val = phy->ops.write_reg(hw, IGP01E1000_PHY_PORT_CTRL, phy_data); + if (ret_val) + goto out; + + DEBUGOUT1("IGP PSCR: %X\n", phy_data); + + usec_delay(1); + + if (phy->autoneg_wait_to_complete) { + DEBUGOUT("Waiting for forced speed/duplex link on IGP phy.\n"); + + ret_val = e1000_phy_has_link_generic(hw, + PHY_FORCE_LIMIT, + 100000, + &link); + if (ret_val) + goto out; + + if (!link) + DEBUGOUT("Link taking longer than expected.\n"); + + /* Try once more */ + ret_val = e1000_phy_has_link_generic(hw, + PHY_FORCE_LIMIT, + 100000, + &link); + if (ret_val) + goto out; + } + +out: + return ret_val; +} + +/** + * e1000_phy_force_speed_duplex_m88 - Force speed/duplex for m88 PHY + * @hw: pointer to the HW structure + * + * Calls the PHY setup function to force speed and duplex. Clears the + * auto-crossover to force MDI manually. Resets the PHY to commit the + * changes. If time expires while waiting for link up, we reset the DSP. + * After reset, TX_CLK and CRS on Tx must be set. Return successful upon + * successful completion, else return corresponding error code. + **/ +s32 e1000_phy_force_speed_duplex_m88(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val; + u16 phy_data; + bool link; + + DEBUGFUNC("e1000_phy_force_speed_duplex_m88"); + + /* + * Clear Auto-Crossover to force MDI manually. M88E1000 requires MDI + * forced whenever speed and duplex are forced. + */ + ret_val = phy->ops.read_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data); + if (ret_val) + goto out; + + phy_data &= ~M88E1000_PSCR_AUTO_X_MODE; + ret_val = phy->ops.write_reg(hw, M88E1000_PHY_SPEC_CTRL, phy_data); + if (ret_val) + goto out; + + DEBUGOUT1("M88E1000 PSCR: %X\n", phy_data); + + ret_val = phy->ops.read_reg(hw, PHY_CONTROL, &phy_data); + if (ret_val) + goto out; + + e1000_phy_force_speed_duplex_setup(hw, &phy_data); + + ret_val = phy->ops.write_reg(hw, PHY_CONTROL, phy_data); + if (ret_val) + goto out; + + /* Reset the phy to commit changes. */ + ret_val = hw->phy.ops.commit(hw); + if (ret_val) + goto out; + + if (phy->autoneg_wait_to_complete) { + DEBUGOUT("Waiting for forced speed/duplex link on M88 phy.\n"); + + ret_val = e1000_phy_has_link_generic(hw, PHY_FORCE_LIMIT, + 100000, &link); + if (ret_val) + goto out; + + if (!link) { + /* + * We didn't get link. + * Reset the DSP and cross our fingers. + */ + ret_val = phy->ops.write_reg(hw, + M88E1000_PHY_PAGE_SELECT, + 0x001d); + if (ret_val) + goto out; + ret_val = e1000_phy_reset_dsp_generic(hw); + if (ret_val) + goto out; + } + + /* Try once more */ + ret_val = e1000_phy_has_link_generic(hw, PHY_FORCE_LIMIT, + 100000, &link); + if (ret_val) + goto out; + } + + ret_val = phy->ops.read_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL, &phy_data); + if (ret_val) + goto out; + + /* + * Resetting the phy means we need to re-force TX_CLK in the + * Extended PHY Specific Control Register to 25MHz clock from + * the reset value of 2.5MHz. + */ + phy_data |= M88E1000_EPSCR_TX_CLK_25; + ret_val = phy->ops.write_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL, phy_data); + if (ret_val) + goto out; + + /* + * In addition, we must re-enable CRS on Tx for both half and full + * duplex. + */ + ret_val = phy->ops.read_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data); + if (ret_val) + goto out; + + phy_data |= M88E1000_PSCR_ASSERT_CRS_ON_TX; + ret_val = phy->ops.write_reg(hw, M88E1000_PHY_SPEC_CTRL, phy_data); + +out: + return ret_val; +} + +/** + * e1000_phy_force_speed_duplex_setup - Configure forced PHY speed/duplex + * @hw: pointer to the HW structure + * @phy_ctrl: pointer to current value of PHY_CONTROL + * + * Forces speed and duplex on the PHY by doing the following: disable flow + * control, force speed/duplex on the MAC, disable auto speed detection, + * disable auto-negotiation, configure duplex, configure speed, configure + * the collision distance, write configuration to CTRL register. The + * caller must write to the PHY_CONTROL register for these settings to + * take affect. + **/ +void e1000_phy_force_speed_duplex_setup(struct e1000_hw *hw, u16 *phy_ctrl) +{ + struct e1000_mac_info *mac = &hw->mac; + u32 ctrl; + + DEBUGFUNC("e1000_phy_force_speed_duplex_setup"); + + /* Turn off flow control when forcing speed/duplex */ + hw->fc.current_mode = e1000_fc_none; + + /* Force speed/duplex on the mac */ + ctrl = E1000_READ_REG(hw, E1000_CTRL); + ctrl |= (E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX); + ctrl &= ~E1000_CTRL_SPD_SEL; + + /* Disable Auto Speed Detection */ + ctrl &= ~E1000_CTRL_ASDE; + + /* Disable autoneg on the phy */ + *phy_ctrl &= ~MII_CR_AUTO_NEG_EN; + + /* Forcing Full or Half Duplex? */ + if (mac->forced_speed_duplex & E1000_ALL_HALF_DUPLEX) { + ctrl &= ~E1000_CTRL_FD; + *phy_ctrl &= ~MII_CR_FULL_DUPLEX; + DEBUGOUT("Half Duplex\n"); + } else { + ctrl |= E1000_CTRL_FD; + *phy_ctrl |= MII_CR_FULL_DUPLEX; + DEBUGOUT("Full Duplex\n"); + } + + /* Forcing 10mb or 100mb? */ + if (mac->forced_speed_duplex & E1000_ALL_100_SPEED) { + ctrl |= E1000_CTRL_SPD_100; + *phy_ctrl |= MII_CR_SPEED_100; + *phy_ctrl &= ~(MII_CR_SPEED_1000 | MII_CR_SPEED_10); + DEBUGOUT("Forcing 100mb\n"); + } else { + ctrl &= ~(E1000_CTRL_SPD_1000 | E1000_CTRL_SPD_100); + *phy_ctrl |= MII_CR_SPEED_10; + *phy_ctrl &= ~(MII_CR_SPEED_1000 | MII_CR_SPEED_100); + DEBUGOUT("Forcing 10mb\n"); + } + + e1000_config_collision_dist_generic(hw); + + E1000_WRITE_REG(hw, E1000_CTRL, ctrl); +} + +/** + * e1000_set_d3_lplu_state_generic - Sets low power link up state for D3 + * @hw: pointer to the HW structure + * @active: boolean used to enable/disable lplu + * + * Success returns 0, Failure returns 1 + * + * The low power link up (lplu) state is set to the power management level D3 + * and SmartSpeed is disabled when active is TRUE, else clear lplu for D3 + * and enable Smartspeed. LPLU and Smartspeed are mutually exclusive. LPLU + * is used during Dx states where the power conservation is most important. + * During driver activity, SmartSpeed should be enabled so performance is + * maintained. + **/ +s32 e1000_set_d3_lplu_state_generic(struct e1000_hw *hw, bool active) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val = E1000_SUCCESS; + u16 data; + + DEBUGFUNC("e1000_set_d3_lplu_state_generic"); + + if (!(hw->phy.ops.read_reg)) + goto out; + + ret_val = phy->ops.read_reg(hw, IGP02E1000_PHY_POWER_MGMT, &data); + if (ret_val) + goto out; + + if (!active) { + data &= ~IGP02E1000_PM_D3_LPLU; + ret_val = phy->ops.write_reg(hw, IGP02E1000_PHY_POWER_MGMT, + data); + if (ret_val) + goto out; + /* + * LPLU and SmartSpeed are mutually exclusive. LPLU is used + * during Dx states where the power conservation is most + * important. During driver activity we should enable + * SmartSpeed, so performance is maintained. + */ + if (phy->smart_speed == e1000_smart_speed_on) { + ret_val = phy->ops.read_reg(hw, + IGP01E1000_PHY_PORT_CONFIG, + &data); + if (ret_val) + goto out; + + data |= IGP01E1000_PSCFR_SMART_SPEED; + ret_val = phy->ops.write_reg(hw, + IGP01E1000_PHY_PORT_CONFIG, + data); + if (ret_val) + goto out; + } else if (phy->smart_speed == e1000_smart_speed_off) { + ret_val = phy->ops.read_reg(hw, + IGP01E1000_PHY_PORT_CONFIG, + &data); + if (ret_val) + goto out; + + data &= ~IGP01E1000_PSCFR_SMART_SPEED; + ret_val = phy->ops.write_reg(hw, + IGP01E1000_PHY_PORT_CONFIG, + data); + if (ret_val) + goto out; + } + } else if ((phy->autoneg_advertised == E1000_ALL_SPEED_DUPLEX) || + (phy->autoneg_advertised == E1000_ALL_NOT_GIG) || + (phy->autoneg_advertised == E1000_ALL_10_SPEED)) { + data |= IGP02E1000_PM_D3_LPLU; + ret_val = phy->ops.write_reg(hw, IGP02E1000_PHY_POWER_MGMT, + data); + if (ret_val) + goto out; + + /* When LPLU is enabled, we should disable SmartSpeed */ + ret_val = phy->ops.read_reg(hw, IGP01E1000_PHY_PORT_CONFIG, + &data); + if (ret_val) + goto out; + + data &= ~IGP01E1000_PSCFR_SMART_SPEED; + ret_val = phy->ops.write_reg(hw, IGP01E1000_PHY_PORT_CONFIG, + data); + } + +out: + return ret_val; +} + +/** + * e1000_check_downshift_generic - Checks whether a downshift in speed occurred + * @hw: pointer to the HW structure + * + * Success returns 0, Failure returns 1 + * + * A downshift is detected by querying the PHY link health. + **/ +s32 e1000_check_downshift_generic(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val; + u16 phy_data, offset, mask; + + DEBUGFUNC("e1000_check_downshift_generic"); + + switch (phy->type) { + case e1000_phy_m88: + case e1000_phy_gg82563: + case e1000_phy_bm: + offset = M88E1000_PHY_SPEC_STATUS; + mask = M88E1000_PSSR_DOWNSHIFT; + break; + case e1000_phy_igp_2: + case e1000_phy_igp: + case e1000_phy_igp_3: + offset = IGP01E1000_PHY_LINK_HEALTH; + mask = IGP01E1000_PLHR_SS_DOWNGRADE; + break; + default: + /* speed downshift not supported */ + phy->speed_downgraded = FALSE; + ret_val = E1000_SUCCESS; + goto out; + } + + ret_val = phy->ops.read_reg(hw, offset, &phy_data); + + if (!ret_val) + phy->speed_downgraded = (phy_data & mask) ? TRUE : FALSE; + +out: + return ret_val; +} + +/** + * e1000_check_polarity_m88 - Checks the polarity. + * @hw: pointer to the HW structure + * + * Success returns 0, Failure returns -E1000_ERR_PHY (-2) + * + * Polarity is determined based on the PHY specific status register. + **/ +s32 e1000_check_polarity_m88(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val; + u16 data; + + DEBUGFUNC("e1000_check_polarity_m88"); + + ret_val = phy->ops.read_reg(hw, M88E1000_PHY_SPEC_STATUS, &data); + + if (!ret_val) + phy->cable_polarity = (data & M88E1000_PSSR_REV_POLARITY) + ? e1000_rev_polarity_reversed + : e1000_rev_polarity_normal; + + return ret_val; +} + +/** + * e1000_check_polarity_igp - Checks the polarity. + * @hw: pointer to the HW structure + * + * Success returns 0, Failure returns -E1000_ERR_PHY (-2) + * + * Polarity is determined based on the PHY port status register, and the + * current speed (since there is no polarity at 100Mbps). + **/ +s32 e1000_check_polarity_igp(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val; + u16 data, offset, mask; + + DEBUGFUNC("e1000_check_polarity_igp"); + + /* + * Polarity is determined based on the speed of + * our connection. + */ + ret_val = phy->ops.read_reg(hw, IGP01E1000_PHY_PORT_STATUS, &data); + if (ret_val) + goto out; + + if ((data & IGP01E1000_PSSR_SPEED_MASK) == + IGP01E1000_PSSR_SPEED_1000MBPS) { + offset = IGP01E1000_PHY_PCS_INIT_REG; + mask = IGP01E1000_PHY_POLARITY_MASK; + } else { + /* + * This really only applies to 10Mbps since + * there is no polarity for 100Mbps (always 0). + */ + offset = IGP01E1000_PHY_PORT_STATUS; + mask = IGP01E1000_PSSR_POLARITY_REVERSED; + } + + ret_val = phy->ops.read_reg(hw, offset, &data); + + if (!ret_val) + phy->cable_polarity = (data & mask) + ? e1000_rev_polarity_reversed + : e1000_rev_polarity_normal; + +out: + return ret_val; +} + +/** + * e1000_wait_autoneg_generic - Wait for auto-neg completion + * @hw: pointer to the HW structure + * + * Waits for auto-negotiation to complete or for the auto-negotiation time + * limit to expire, which ever happens first. + **/ +s32 e1000_wait_autoneg_generic(struct e1000_hw *hw) +{ + s32 ret_val = E1000_SUCCESS; + u16 i, phy_status; + + DEBUGFUNC("e1000_wait_autoneg_generic"); + + if (!(hw->phy.ops.read_reg)) + return E1000_SUCCESS; + + /* Break after autoneg completes or PHY_AUTO_NEG_LIMIT expires. */ + for (i = PHY_AUTO_NEG_LIMIT; i > 0; i--) { + ret_val = hw->phy.ops.read_reg(hw, PHY_STATUS, &phy_status); + if (ret_val) + break; + ret_val = hw->phy.ops.read_reg(hw, PHY_STATUS, &phy_status); + if (ret_val) + break; + if (phy_status & MII_SR_AUTONEG_COMPLETE) + break; + msec_delay(100); + } + + /* + * PHY_AUTO_NEG_TIME expiration doesn't guarantee auto-negotiation + * has completed. + */ + return ret_val; +} + +/** + * e1000_phy_has_link_generic - Polls PHY for link + * @hw: pointer to the HW structure + * @iterations: number of times to poll for link + * @usec_interval: delay between polling attempts + * @success: pointer to whether polling was successful or not + * + * Polls the PHY status register for link, 'iterations' number of times. + **/ +s32 e1000_phy_has_link_generic(struct e1000_hw *hw, u32 iterations, + u32 usec_interval, bool *success) +{ + s32 ret_val = E1000_SUCCESS; + u16 i, phy_status; + + DEBUGFUNC("e1000_phy_has_link_generic"); + + if (!(hw->phy.ops.read_reg)) + return E1000_SUCCESS; + + for (i = 0; i < iterations; i++) { + /* + * Some PHYs require the PHY_STATUS register to be read + * twice due to the link bit being sticky. No harm doing + * it across the board. + */ + ret_val = hw->phy.ops.read_reg(hw, PHY_STATUS, &phy_status); + if (ret_val) + break; + ret_val = hw->phy.ops.read_reg(hw, PHY_STATUS, &phy_status); + if (ret_val) + break; + if (phy_status & MII_SR_LINK_STATUS) + break; + if (usec_interval >= 1000) + msec_delay_irq(usec_interval/1000); + else + usec_delay(usec_interval); + } + + *success = (i < iterations) ? TRUE : FALSE; + + return ret_val; +} + +/** + * e1000_get_cable_length_m88 - Determine cable length for m88 PHY + * @hw: pointer to the HW structure + * + * Reads the PHY specific status register to retrieve the cable length + * information. The cable length is determined by averaging the minimum and + * maximum values to get the "average" cable length. The m88 PHY has four + * possible cable length values, which are: + * Register Value Cable Length + * 0 < 50 meters + * 1 50 - 80 meters + * 2 80 - 110 meters + * 3 110 - 140 meters + * 4 > 140 meters + **/ +s32 e1000_get_cable_length_m88(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val; + u16 phy_data, index; + + DEBUGFUNC("e1000_get_cable_length_m88"); + + ret_val = phy->ops.read_reg(hw, M88E1000_PHY_SPEC_STATUS, &phy_data); + if (ret_val) + goto out; + + index = (phy_data & M88E1000_PSSR_CABLE_LENGTH) >> + M88E1000_PSSR_CABLE_LENGTH_SHIFT; + if (index < M88E1000_CABLE_LENGTH_TABLE_SIZE + 1) { + phy->min_cable_length = e1000_m88_cable_length_table[index]; + phy->max_cable_length = e1000_m88_cable_length_table[index+1]; + + phy->cable_length = (phy->min_cable_length + + phy->max_cable_length) / 2; + } else { + ret_val = E1000_ERR_PHY; + } + +out: + return ret_val; +} + +/** + * e1000_get_cable_length_igp_2 - Determine cable length for igp2 PHY + * @hw: pointer to the HW structure + * + * The automatic gain control (agc) normalizes the amplitude of the + * received signal, adjusting for the attenuation produced by the + * cable. By reading the AGC registers, which represent the + * combination of coarse and fine gain value, the value can be put + * into a lookup table to obtain the approximate cable length + * for each channel. + **/ +s32 e1000_get_cable_length_igp_2(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val = E1000_SUCCESS; + u16 phy_data, i, agc_value = 0; + u16 cur_agc_index, max_agc_index = 0; + u16 min_agc_index = IGP02E1000_CABLE_LENGTH_TABLE_SIZE - 1; + u16 agc_reg_array[IGP02E1000_PHY_CHANNEL_NUM] = + {IGP02E1000_PHY_AGC_A, + IGP02E1000_PHY_AGC_B, + IGP02E1000_PHY_AGC_C, + IGP02E1000_PHY_AGC_D}; + + DEBUGFUNC("e1000_get_cable_length_igp_2"); + + /* Read the AGC registers for all channels */ + for (i = 0; i < IGP02E1000_PHY_CHANNEL_NUM; i++) { + ret_val = phy->ops.read_reg(hw, agc_reg_array[i], &phy_data); + if (ret_val) + goto out; + + /* + * Getting bits 15:9, which represent the combination of + * coarse and fine gain values. The result is a number + * that can be put into the lookup table to obtain the + * approximate cable length. + */ + cur_agc_index = (phy_data >> IGP02E1000_AGC_LENGTH_SHIFT) & + IGP02E1000_AGC_LENGTH_MASK; + + /* Array index bound check. */ + if ((cur_agc_index >= IGP02E1000_CABLE_LENGTH_TABLE_SIZE) || + (cur_agc_index == 0)) { + ret_val = -E1000_ERR_PHY; + goto out; + } + + /* Remove min & max AGC values from calculation. */ + if (e1000_igp_2_cable_length_table[min_agc_index] > + e1000_igp_2_cable_length_table[cur_agc_index]) + min_agc_index = cur_agc_index; + if (e1000_igp_2_cable_length_table[max_agc_index] < + e1000_igp_2_cable_length_table[cur_agc_index]) + max_agc_index = cur_agc_index; + + agc_value += e1000_igp_2_cable_length_table[cur_agc_index]; + } + + agc_value -= (e1000_igp_2_cable_length_table[min_agc_index] + + e1000_igp_2_cable_length_table[max_agc_index]); + agc_value /= (IGP02E1000_PHY_CHANNEL_NUM - 2); + + /* Calculate cable length with the error range of +/- 10 meters. */ + phy->min_cable_length = ((agc_value - IGP02E1000_AGC_RANGE) > 0) ? + (agc_value - IGP02E1000_AGC_RANGE) : 0; + phy->max_cable_length = agc_value + IGP02E1000_AGC_RANGE; + + phy->cable_length = (phy->min_cable_length + phy->max_cable_length) / 2; + +out: + return ret_val; +} + +/** + * e1000_get_phy_info_m88 - Retrieve PHY information + * @hw: pointer to the HW structure + * + * Valid for only copper links. Read the PHY status register (sticky read) + * to verify that link is up. Read the PHY special control register to + * determine the polarity and 10base-T extended distance. Read the PHY + * special status register to determine MDI/MDIx and current speed. If + * speed is 1000, then determine cable length, local and remote receiver. + **/ +s32 e1000_get_phy_info_m88(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val; + u16 phy_data; + bool link; + + DEBUGFUNC("e1000_get_phy_info_m88"); + + if (hw->phy.media_type != e1000_media_type_copper) { + DEBUGOUT("Phy info is only valid for copper media\n"); + ret_val = -E1000_ERR_CONFIG; + goto out; + } + + ret_val = e1000_phy_has_link_generic(hw, 1, 0, &link); + if (ret_val) + goto out; + + if (!link) { + DEBUGOUT("Phy info is only valid if link is up\n"); + ret_val = -E1000_ERR_CONFIG; + goto out; + } + + ret_val = phy->ops.read_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data); + if (ret_val) + goto out; + + phy->polarity_correction = (phy_data & M88E1000_PSCR_POLARITY_REVERSAL) + ? TRUE : FALSE; + + ret_val = e1000_check_polarity_m88(hw); + if (ret_val) + goto out; + + ret_val = phy->ops.read_reg(hw, M88E1000_PHY_SPEC_STATUS, &phy_data); + if (ret_val) + goto out; + + phy->is_mdix = (phy_data & M88E1000_PSSR_MDIX) ? TRUE : FALSE; + + if ((phy_data & M88E1000_PSSR_SPEED) == M88E1000_PSSR_1000MBS) { + ret_val = hw->phy.ops.get_cable_length(hw); + if (ret_val) + goto out; + + ret_val = phy->ops.read_reg(hw, PHY_1000T_STATUS, &phy_data); + if (ret_val) + goto out; + + phy->local_rx = (phy_data & SR_1000T_LOCAL_RX_STATUS) + ? e1000_1000t_rx_status_ok + : e1000_1000t_rx_status_not_ok; + + phy->remote_rx = (phy_data & SR_1000T_REMOTE_RX_STATUS) + ? e1000_1000t_rx_status_ok + : e1000_1000t_rx_status_not_ok; + } else { + /* Set values to "undefined" */ + phy->cable_length = E1000_CABLE_LENGTH_UNDEFINED; + phy->local_rx = e1000_1000t_rx_status_undefined; + phy->remote_rx = e1000_1000t_rx_status_undefined; + } + +out: + return ret_val; +} + +/** + * e1000_get_phy_info_igp - Retrieve igp PHY information + * @hw: pointer to the HW structure + * + * Read PHY status to determine if link is up. If link is up, then + * set/determine 10base-T extended distance and polarity correction. Read + * PHY port status to determine MDI/MDIx and speed. Based on the speed, + * determine on the cable length, local and remote receiver. + **/ +s32 e1000_get_phy_info_igp(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val; + u16 data; + bool link; + + DEBUGFUNC("e1000_get_phy_info_igp"); + + ret_val = e1000_phy_has_link_generic(hw, 1, 0, &link); + if (ret_val) + goto out; + + if (!link) { + DEBUGOUT("Phy info is only valid if link is up\n"); + ret_val = -E1000_ERR_CONFIG; + goto out; + } + + phy->polarity_correction = TRUE; + + ret_val = e1000_check_polarity_igp(hw); + if (ret_val) + goto out; + + ret_val = phy->ops.read_reg(hw, IGP01E1000_PHY_PORT_STATUS, &data); + if (ret_val) + goto out; + + phy->is_mdix = (data & IGP01E1000_PSSR_MDIX) ? TRUE : FALSE; + + if ((data & IGP01E1000_PSSR_SPEED_MASK) == + IGP01E1000_PSSR_SPEED_1000MBPS) { + ret_val = hw->phy.ops.get_cable_length(hw); + if (ret_val) + goto out; + + ret_val = phy->ops.read_reg(hw, PHY_1000T_STATUS, &data); + if (ret_val) + goto out; + + phy->local_rx = (data & SR_1000T_LOCAL_RX_STATUS) + ? e1000_1000t_rx_status_ok + : e1000_1000t_rx_status_not_ok; + + phy->remote_rx = (data & SR_1000T_REMOTE_RX_STATUS) + ? e1000_1000t_rx_status_ok + : e1000_1000t_rx_status_not_ok; + } else { + phy->cable_length = E1000_CABLE_LENGTH_UNDEFINED; + phy->local_rx = e1000_1000t_rx_status_undefined; + phy->remote_rx = e1000_1000t_rx_status_undefined; + } + +out: + return ret_val; +} + +/** + * e1000_phy_sw_reset_generic - PHY software reset + * @hw: pointer to the HW structure + * + * Does a software reset of the PHY by reading the PHY control register and + * setting/write the control register reset bit to the PHY. + **/ +s32 e1000_phy_sw_reset_generic(struct e1000_hw *hw) +{ + s32 ret_val = E1000_SUCCESS; + u16 phy_ctrl; + + DEBUGFUNC("e1000_phy_sw_reset_generic"); + + if (!(hw->phy.ops.read_reg)) + goto out; + + ret_val = hw->phy.ops.read_reg(hw, PHY_CONTROL, &phy_ctrl); + if (ret_val) + goto out; + + phy_ctrl |= MII_CR_RESET; + ret_val = hw->phy.ops.write_reg(hw, PHY_CONTROL, phy_ctrl); + if (ret_val) + goto out; + + usec_delay(1); + +out: + return ret_val; +} + +/** + * e1000_phy_hw_reset_generic - PHY hardware reset + * @hw: pointer to the HW structure + * + * Verify the reset block is not blocking us from resetting. Acquire + * semaphore (if necessary) and read/set/write the device control reset + * bit in the PHY. Wait the appropriate delay time for the device to + * reset and release the semaphore (if necessary). + **/ +s32 e1000_phy_hw_reset_generic(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val = E1000_SUCCESS; + u32 ctrl; + + DEBUGFUNC("e1000_phy_hw_reset_generic"); + + ret_val = phy->ops.check_reset_block(hw); + if (ret_val) { + ret_val = E1000_SUCCESS; + goto out; + } + + ret_val = phy->ops.acquire(hw); + if (ret_val) + goto out; + + ctrl = E1000_READ_REG(hw, E1000_CTRL); + E1000_WRITE_REG(hw, E1000_CTRL, ctrl | E1000_CTRL_PHY_RST); + E1000_WRITE_FLUSH(hw); + + usec_delay(phy->reset_delay_us); + + E1000_WRITE_REG(hw, E1000_CTRL, ctrl); + E1000_WRITE_FLUSH(hw); + + usec_delay(150); + + phy->ops.release(hw); + + ret_val = phy->ops.get_cfg_done(hw); + +out: + return ret_val; +} + +/** + * e1000_get_cfg_done_generic - Generic configuration done + * @hw: pointer to the HW structure + * + * Generic function to wait 10 milli-seconds for configuration to complete + * and return success. + **/ +s32 e1000_get_cfg_done_generic(struct e1000_hw *hw) +{ + DEBUGFUNC("e1000_get_cfg_done_generic"); + + msec_delay_irq(10); + + return E1000_SUCCESS; +} + +/** + * e1000_phy_init_script_igp3 - Inits the IGP3 PHY + * @hw: pointer to the HW structure + * + * Initializes a Intel Gigabit PHY3 when an EEPROM is not present. + **/ +s32 e1000_phy_init_script_igp3(struct e1000_hw *hw) +{ + DEBUGOUT("Running IGP 3 PHY init script\n"); + + /* PHY init IGP 3 */ + /* Enable rise/fall, 10-mode work in class-A */ + hw->phy.ops.write_reg(hw, 0x2F5B, 0x9018); + /* Remove all caps from Replica path filter */ + hw->phy.ops.write_reg(hw, 0x2F52, 0x0000); + /* Bias trimming for ADC, AFE and Driver (Default) */ + hw->phy.ops.write_reg(hw, 0x2FB1, 0x8B24); + /* Increase Hybrid poly bias */ + hw->phy.ops.write_reg(hw, 0x2FB2, 0xF8F0); + /* Add 4% to Tx amplitude in Gig mode */ + hw->phy.ops.write_reg(hw, 0x2010, 0x10B0); + /* Disable trimming (TTT) */ + hw->phy.ops.write_reg(hw, 0x2011, 0x0000); + /* Poly DC correction to 94.6% + 2% for all channels */ + hw->phy.ops.write_reg(hw, 0x20DD, 0x249A); + /* ABS DC correction to 95.9% */ + hw->phy.ops.write_reg(hw, 0x20DE, 0x00D3); + /* BG temp curve trim */ + hw->phy.ops.write_reg(hw, 0x28B4, 0x04CE); + /* Increasing ADC OPAMP stage 1 currents to max */ + hw->phy.ops.write_reg(hw, 0x2F70, 0x29E4); + /* Force 1000 ( required for enabling PHY regs configuration) */ + hw->phy.ops.write_reg(hw, 0x0000, 0x0140); + /* Set upd_freq to 6 */ + hw->phy.ops.write_reg(hw, 0x1F30, 0x1606); + /* Disable NPDFE */ + hw->phy.ops.write_reg(hw, 0x1F31, 0xB814); + /* Disable adaptive fixed FFE (Default) */ + hw->phy.ops.write_reg(hw, 0x1F35, 0x002A); + /* Enable FFE hysteresis */ + hw->phy.ops.write_reg(hw, 0x1F3E, 0x0067); + /* Fixed FFE for short cable lengths */ + hw->phy.ops.write_reg(hw, 0x1F54, 0x0065); + /* Fixed FFE for medium cable lengths */ + hw->phy.ops.write_reg(hw, 0x1F55, 0x002A); + /* Fixed FFE for long cable lengths */ + hw->phy.ops.write_reg(hw, 0x1F56, 0x002A); + /* Enable Adaptive Clip Threshold */ + hw->phy.ops.write_reg(hw, 0x1F72, 0x3FB0); + /* AHT reset limit to 1 */ + hw->phy.ops.write_reg(hw, 0x1F76, 0xC0FF); + /* Set AHT master delay to 127 msec */ + hw->phy.ops.write_reg(hw, 0x1F77, 0x1DEC); + /* Set scan bits for AHT */ + hw->phy.ops.write_reg(hw, 0x1F78, 0xF9EF); + /* Set AHT Preset bits */ + hw->phy.ops.write_reg(hw, 0x1F79, 0x0210); + /* Change integ_factor of channel A to 3 */ + hw->phy.ops.write_reg(hw, 0x1895, 0x0003); + /* Change prop_factor of channels BCD to 8 */ + hw->phy.ops.write_reg(hw, 0x1796, 0x0008); + /* Change cg_icount + enable integbp for channels BCD */ + hw->phy.ops.write_reg(hw, 0x1798, 0xD008); + /* + * Change cg_icount + enable integbp + change prop_factor_master + * to 8 for channel A + */ + hw->phy.ops.write_reg(hw, 0x1898, 0xD918); + /* Disable AHT in Slave mode on channel A */ + hw->phy.ops.write_reg(hw, 0x187A, 0x0800); + /* + * Enable LPLU and disable AN to 1000 in non-D0a states, + * Enable SPD+B2B + */ + hw->phy.ops.write_reg(hw, 0x0019, 0x008D); + /* Enable restart AN on an1000_dis change */ + hw->phy.ops.write_reg(hw, 0x001B, 0x2080); + /* Enable wh_fifo read clock in 10/100 modes */ + hw->phy.ops.write_reg(hw, 0x0014, 0x0045); + /* Restart AN, Speed selection is 1000 */ + hw->phy.ops.write_reg(hw, 0x0000, 0x1340); + + return E1000_SUCCESS; +} + +/** + * e1000_get_phy_type_from_id - Get PHY type from id + * @phy_id: phy_id read from the phy + * + * Returns the phy type from the id. + **/ +enum e1000_phy_type e1000_get_phy_type_from_id(u32 phy_id) +{ + enum e1000_phy_type phy_type = e1000_phy_unknown; + + switch (phy_id) { + case M88E1000_I_PHY_ID: + case M88E1000_E_PHY_ID: + case M88E1111_I_PHY_ID: + case M88E1011_I_PHY_ID: + phy_type = e1000_phy_m88; + break; + case IGP01E1000_I_PHY_ID: /* IGP 1 & 2 share this */ + phy_type = e1000_phy_igp_2; + break; + case GG82563_E_PHY_ID: + phy_type = e1000_phy_gg82563; + break; + case IGP03E1000_E_PHY_ID: + phy_type = e1000_phy_igp_3; + break; + case IFE_E_PHY_ID: + case IFE_PLUS_E_PHY_ID: + case IFE_C_E_PHY_ID: + phy_type = e1000_phy_ife; + break; + case BME1000_E_PHY_ID: + case BME1000_E_PHY_ID_R2: + phy_type = e1000_phy_bm; + break; + default: + phy_type = e1000_phy_unknown; + break; + } + return phy_type; +} + +/** + * e1000_determine_phy_address - Determines PHY address. + * @hw: pointer to the HW structure + * + * This uses a trial and error method to loop through possible PHY + * addresses. It tests each by reading the PHY ID registers and + * checking for a match. + **/ +s32 e1000_determine_phy_address(struct e1000_hw *hw) +{ + s32 ret_val = -E1000_ERR_PHY_TYPE; + u32 phy_addr = 0; + u32 i; + enum e1000_phy_type phy_type = e1000_phy_unknown; + + for (phy_addr = 0; phy_addr < E1000_MAX_PHY_ADDR; phy_addr++) { + hw->phy.addr = phy_addr; + i = 0; + + do { + e1000_get_phy_id(hw); + phy_type = e1000_get_phy_type_from_id(hw->phy.id); + + /* + * If phy_type is valid, break - we found our + * PHY address + */ + if (phy_type != e1000_phy_unknown) { + ret_val = E1000_SUCCESS; + goto out; + } + msec_delay(1); + i++; + } while (i < 10); + } + +out: + return ret_val; +} + +/** + * e1000_get_phy_addr_for_bm_page - Retrieve PHY page address + * @page: page to access + * + * Returns the phy address for the page requested. + **/ +static u32 e1000_get_phy_addr_for_bm_page(u32 page, u32 reg) +{ + u32 phy_addr = 2; + + if ((page >= 768) || (page == 0 && reg == 25) || (reg == 31)) + phy_addr = 1; + + return phy_addr; +} + +/** + * e1000_write_phy_reg_bm - Write BM PHY register + * @hw: pointer to the HW structure + * @offset: register offset to write to + * @data: data to write at register offset + * + * Acquires semaphore, if necessary, then writes the data to PHY register + * at the offset. Release any acquired semaphores before exiting. + **/ +s32 e1000_write_phy_reg_bm(struct e1000_hw *hw, u32 offset, u16 data) +{ + s32 ret_val; + u32 page_select = 0; + u32 page = offset >> IGP_PAGE_SHIFT; + u32 page_shift = 0; + + DEBUGFUNC("e1000_write_phy_reg_bm"); + + /* Page 800 works differently than the rest so it has its own func */ + if (page == BM_WUC_PAGE) { + ret_val = e1000_access_phy_wakeup_reg_bm(hw, offset, &data, + FALSE); + goto out; + } + + ret_val = hw->phy.ops.acquire(hw); + if (ret_val) + goto out; + + hw->phy.addr = e1000_get_phy_addr_for_bm_page(page, offset); + + if (offset > MAX_PHY_MULTI_PAGE_REG) { + /* + * Page select is register 31 for phy address 1 and 22 for + * phy address 2 and 3. Page select is shifted only for + * phy address 1. + */ + if (hw->phy.addr == 1) { + page_shift = IGP_PAGE_SHIFT; + page_select = IGP01E1000_PHY_PAGE_SELECT; + } else { + page_shift = 0; + page_select = BM_PHY_PAGE_SELECT; + } + + /* Page is shifted left, PHY expects (page x 32) */ + ret_val = e1000_write_phy_reg_mdic(hw, page_select, + (page << page_shift)); + if (ret_val) { + hw->phy.ops.release(hw); + goto out; + } + } + + ret_val = e1000_write_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & offset, + data); + + hw->phy.ops.release(hw); + +out: + return ret_val; +} + +/** + * e1000_read_phy_reg_bm - Read BM PHY register + * @hw: pointer to the HW structure + * @offset: register offset to be read + * @data: pointer to the read data + * + * Acquires semaphore, if necessary, then reads the PHY register at offset + * and storing the retrieved information in data. Release any acquired + * semaphores before exiting. + **/ +s32 e1000_read_phy_reg_bm(struct e1000_hw *hw, u32 offset, u16 *data) +{ + s32 ret_val; + u32 page_select = 0; + u32 page = offset >> IGP_PAGE_SHIFT; + u32 page_shift = 0; + + DEBUGFUNC("e1000_read_phy_reg_bm"); + + /* Page 800 works differently than the rest so it has its own func */ + if (page == BM_WUC_PAGE) { + ret_val = e1000_access_phy_wakeup_reg_bm(hw, offset, data, + TRUE); + goto out; + } + + ret_val = hw->phy.ops.acquire(hw); + if (ret_val) + goto out; + + hw->phy.addr = e1000_get_phy_addr_for_bm_page(page, offset); + + if (offset > MAX_PHY_MULTI_PAGE_REG) { + /* + * Page select is register 31 for phy address 1 and 22 for + * phy address 2 and 3. Page select is shifted only for + * phy address 1. + */ + if (hw->phy.addr == 1) { + page_shift = IGP_PAGE_SHIFT; + page_select = IGP01E1000_PHY_PAGE_SELECT; + } else { + page_shift = 0; + page_select = BM_PHY_PAGE_SELECT; + } + + /* Page is shifted left, PHY expects (page x 32) */ + ret_val = e1000_write_phy_reg_mdic(hw, page_select, + (page << page_shift)); + if (ret_val) { + hw->phy.ops.release(hw); + goto out; + } + } + + ret_val = e1000_read_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & offset, + data); + hw->phy.ops.release(hw); + +out: + return ret_val; +} + +/** + * e1000_read_phy_reg_bm2 - Read BM PHY register + * @hw: pointer to the HW structure + * @offset: register offset to be read + * @data: pointer to the read data + * + * Acquires semaphore, if necessary, then reads the PHY register at offset + * and storing the retrieved information in data. Release any acquired + * semaphores before exiting. + **/ +s32 e1000_read_phy_reg_bm2(struct e1000_hw *hw, u32 offset, u16 *data) +{ + s32 ret_val; + u16 page = (u16)(offset >> IGP_PAGE_SHIFT); + + DEBUGFUNC("e1000_write_phy_reg_bm2"); + + /* Page 800 works differently than the rest so it has its own func */ + if (page == BM_WUC_PAGE) { + ret_val = e1000_access_phy_wakeup_reg_bm(hw, offset, data, + TRUE); + goto out; + } + + ret_val = hw->phy.ops.acquire(hw); + if (ret_val) + goto out; + + hw->phy.addr = 1; + + if (offset > MAX_PHY_MULTI_PAGE_REG) { + + /* Page is shifted left, PHY expects (page x 32) */ + ret_val = e1000_write_phy_reg_mdic(hw, BM_PHY_PAGE_SELECT, + page); + + if (ret_val) { + hw->phy.ops.release(hw); + goto out; + } + } + + ret_val = e1000_read_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & offset, + data); + hw->phy.ops.release(hw); + +out: + return ret_val; +} + +/** + * e1000_write_phy_reg_bm2 - Write BM PHY register + * @hw: pointer to the HW structure + * @offset: register offset to write to + * @data: data to write at register offset + * + * Acquires semaphore, if necessary, then writes the data to PHY register + * at the offset. Release any acquired semaphores before exiting. + **/ +s32 e1000_write_phy_reg_bm2(struct e1000_hw *hw, u32 offset, u16 data) +{ + s32 ret_val; + u16 page = (u16)(offset >> IGP_PAGE_SHIFT); + + DEBUGFUNC("e1000_write_phy_reg_bm2"); + + /* Page 800 works differently than the rest so it has its own func */ + if (page == BM_WUC_PAGE) { + ret_val = e1000_access_phy_wakeup_reg_bm(hw, offset, &data, + FALSE); + goto out; + } + + ret_val = hw->phy.ops.acquire(hw); + if (ret_val) + goto out; + + hw->phy.addr = 1; + + if (offset > MAX_PHY_MULTI_PAGE_REG) { + /* Page is shifted left, PHY expects (page x 32) */ + ret_val = e1000_write_phy_reg_mdic(hw, BM_PHY_PAGE_SELECT, + page); + + if (ret_val) { + hw->phy.ops.release(hw); + goto out; + } + } + + ret_val = e1000_write_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & offset, + data); + + hw->phy.ops.release(hw); + +out: + return ret_val; +} + +/** + * e1000_access_phy_wakeup_reg_bm - Read BM PHY wakeup register + * @hw: pointer to the HW structure + * @offset: register offset to be read or written + * @data: pointer to the data to read or write + * @read: determines if operation is read or write + * + * Acquires semaphore, if necessary, then reads the PHY register at offset + * and storing the retrieved information in data. Release any acquired + * semaphores before exiting. Note that procedure to read the wakeup + * registers are different. It works as such: + * 1) Set page 769, register 17, bit 2 = 1 + * 2) Set page to 800 for host (801 if we were manageability) + * 3) Write the address using the address opcode (0x11) + * 4) Read or write the data using the data opcode (0x12) + * 5) Restore 769_17.2 to its original value + **/ +static s32 e1000_access_phy_wakeup_reg_bm(struct e1000_hw *hw, u32 offset, + u16 *data, bool read) +{ + s32 ret_val; + u16 reg = ((u16)offset); + u16 phy_reg = 0; + u8 phy_acquired = 1; + + DEBUGFUNC("e1000_read_phy_wakeup_reg_bm"); + + ret_val = hw->phy.ops.acquire(hw); + if (ret_val) { + DEBUGOUT("Could not acquire PHY\n"); + phy_acquired = 0; + goto out; + } + + /* All operations in this function are phy address 1 */ + hw->phy.addr = 1; + + /* Set page 769 */ + e1000_write_phy_reg_mdic(hw, IGP01E1000_PHY_PAGE_SELECT, + (BM_WUC_ENABLE_PAGE << IGP_PAGE_SHIFT)); + + ret_val = e1000_read_phy_reg_mdic(hw, BM_WUC_ENABLE_REG, &phy_reg); + if (ret_val) { + DEBUGOUT("Could not read PHY page 769\n"); + goto out; + } + + /* First clear bit 4 to avoid a power state change */ + phy_reg &= ~(BM_WUC_HOST_WU_BIT); + ret_val = e1000_write_phy_reg_mdic(hw, BM_WUC_ENABLE_REG, phy_reg); + if (ret_val) { + DEBUGOUT("Could not clear PHY page 769 bit 4\n"); + goto out; + } + + /* Write bit 2 = 1, and clear bit 4 to 769_17 */ + ret_val = e1000_write_phy_reg_mdic(hw, BM_WUC_ENABLE_REG, + phy_reg | BM_WUC_ENABLE_BIT); + if (ret_val) { + DEBUGOUT("Could not write PHY page 769 bit 2\n"); + goto out; + } + + /* Select page 800 */ + ret_val = e1000_write_phy_reg_mdic(hw, + IGP01E1000_PHY_PAGE_SELECT, + (BM_WUC_PAGE << IGP_PAGE_SHIFT)); + + /* Write the page 800 offset value using opcode 0x11 */ + ret_val = e1000_write_phy_reg_mdic(hw, BM_WUC_ADDRESS_OPCODE, reg); + if (ret_val) { + DEBUGOUT("Could not write address opcode to page 800\n"); + goto out; + } + + if (read) { + /* Read the page 800 value using opcode 0x12 */ + ret_val = e1000_read_phy_reg_mdic(hw, BM_WUC_DATA_OPCODE, + data); + } else { + /* Read the page 800 value using opcode 0x12 */ + ret_val = e1000_write_phy_reg_mdic(hw, BM_WUC_DATA_OPCODE, + *data); + } + + if (ret_val) { + DEBUGOUT("Could not read data value from page 800\n"); + goto out; + } + + /* + * Restore 769_17.2 to its original value + * Set page 769 + */ + e1000_write_phy_reg_mdic(hw, IGP01E1000_PHY_PAGE_SELECT, + (BM_WUC_ENABLE_PAGE << IGP_PAGE_SHIFT)); + + /* Clear 769_17.2 */ + ret_val = e1000_write_phy_reg_mdic(hw, BM_WUC_ENABLE_REG, phy_reg); + if (ret_val) { + DEBUGOUT("Could not clear PHY page 769 bit 2\n"); + goto out; + } + +out: + if (phy_acquired == 1) + hw->phy.ops.release(hw); + return ret_val; +} + +/** + * e1000_power_up_phy_copper - Restore copper link in case of PHY power down + * @hw: pointer to the HW structure + * + * In the case of a PHY power down to save power, or to turn off link during a + * driver unload, or wake on lan is not enabled, restore the link to previous + * settings. + **/ +void e1000_power_up_phy_copper(struct e1000_hw *hw) +{ + u16 mii_reg = 0; + + /* The PHY will retain its settings across a power down/up cycle */ + hw->phy.ops.read_reg(hw, PHY_CONTROL, &mii_reg); + mii_reg &= ~MII_CR_POWER_DOWN; + hw->phy.ops.write_reg(hw, PHY_CONTROL, mii_reg); +} + +/** + * e1000_power_down_phy_copper - Restore copper link in case of PHY power down + * @hw: pointer to the HW structure + * + * In the case of a PHY power down to save power, or to turn off link during a + * driver unload, or wake on lan is not enabled, restore the link to previous + * settings. + **/ +void e1000_power_down_phy_copper(struct e1000_hw *hw) +{ + u16 mii_reg = 0; + + /* The PHY will retain its settings across a power down/up cycle */ + hw->phy.ops.read_reg(hw, PHY_CONTROL, &mii_reg); + mii_reg |= MII_CR_POWER_DOWN; + hw->phy.ops.write_reg(hw, PHY_CONTROL, mii_reg); + msec_delay(1); +} diff --git a/sys/dev/netif/ig_hal/e1000_phy.h b/sys/dev/netif/ig_hal/e1000_phy.h new file mode 100644 index 0000000000..06bcaf02be --- /dev/null +++ b/sys/dev/netif/ig_hal/e1000_phy.h @@ -0,0 +1,185 @@ +/***************************************************************************** + + Copyright (c) 2001-2008, Intel Corporation + All rights reserved. + + Redistribution and use in source and binary forms, with or without + modification, are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, + this list of conditions and the following disclaimer. + + 2. Redistributions in binary form must reproduce the above copyright + notice, this list of conditions and the following disclaimer in the + documentation and/or other materials provided with the distribution. + + 3. Neither the name of the Intel Corporation nor the names of its + contributors may be used to endorse or promote products derived from + this software without specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE + ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE + LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR + CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF + SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS + INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN + CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) + ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + POSSIBILITY OF SUCH DAMAGE. + +******************************************************************************/ +/*$FreeBSD$*/ + +#ifndef _E1000_PHY_H_ +#define _E1000_PHY_H_ + +void e1000_init_phy_ops_generic(struct e1000_hw *hw); +s32 e1000_null_read_reg(struct e1000_hw *hw, u32 offset, u16 *data); +void e1000_null_phy_generic(struct e1000_hw *hw); +s32 e1000_null_lplu_state(struct e1000_hw *hw, bool active); +s32 e1000_null_write_reg(struct e1000_hw *hw, u32 offset, u16 data); +s32 e1000_check_downshift_generic(struct e1000_hw *hw); +s32 e1000_check_polarity_m88(struct e1000_hw *hw); +s32 e1000_check_polarity_igp(struct e1000_hw *hw); +s32 e1000_check_reset_block_generic(struct e1000_hw *hw); +s32 e1000_copper_link_autoneg(struct e1000_hw *hw); +s32 e1000_copper_link_setup_igp(struct e1000_hw *hw); +s32 e1000_copper_link_setup_m88(struct e1000_hw *hw); +s32 e1000_phy_force_speed_duplex_igp(struct e1000_hw *hw); +s32 e1000_phy_force_speed_duplex_m88(struct e1000_hw *hw); +s32 e1000_get_cable_length_m88(struct e1000_hw *hw); +s32 e1000_get_cable_length_igp_2(struct e1000_hw *hw); +s32 e1000_get_cfg_done_generic(struct e1000_hw *hw); +s32 e1000_get_phy_id(struct e1000_hw *hw); +s32 e1000_get_phy_info_igp(struct e1000_hw *hw); +s32 e1000_get_phy_info_m88(struct e1000_hw *hw); +s32 e1000_phy_sw_reset_generic(struct e1000_hw *hw); +void e1000_phy_force_speed_duplex_setup(struct e1000_hw *hw, u16 *phy_ctrl); +s32 e1000_phy_hw_reset_generic(struct e1000_hw *hw); +s32 e1000_phy_reset_dsp_generic(struct e1000_hw *hw); +s32 e1000_phy_setup_autoneg(struct e1000_hw *hw); +s32 e1000_read_kmrn_reg_generic(struct e1000_hw *hw, u32 offset, u16 *data); +s32 e1000_read_phy_reg_igp(struct e1000_hw *hw, u32 offset, u16 *data); +s32 e1000_read_phy_reg_m88(struct e1000_hw *hw, u32 offset, u16 *data); +s32 e1000_set_d3_lplu_state_generic(struct e1000_hw *hw, bool active); +s32 e1000_setup_copper_link_generic(struct e1000_hw *hw); +s32 e1000_wait_autoneg_generic(struct e1000_hw *hw); +s32 e1000_write_kmrn_reg_generic(struct e1000_hw *hw, u32 offset, u16 data); +s32 e1000_write_phy_reg_igp(struct e1000_hw *hw, u32 offset, u16 data); +s32 e1000_write_phy_reg_m88(struct e1000_hw *hw, u32 offset, u16 data); +s32 e1000_phy_reset_dsp(struct e1000_hw *hw); +s32 e1000_phy_has_link_generic(struct e1000_hw *hw, u32 iterations, + u32 usec_interval, bool *success); +s32 e1000_phy_init_script_igp3(struct e1000_hw *hw); +enum e1000_phy_type e1000_get_phy_type_from_id(u32 phy_id); +s32 e1000_determine_phy_address(struct e1000_hw *hw); +s32 e1000_write_phy_reg_bm(struct e1000_hw *hw, u32 offset, u16 data); +s32 e1000_read_phy_reg_bm(struct e1000_hw *hw, u32 offset, u16 *data); +s32 e1000_read_phy_reg_bm2(struct e1000_hw *hw, u32 offset, u16 *data); +s32 e1000_write_phy_reg_bm2(struct e1000_hw *hw, u32 offset, u16 data); +void e1000_power_up_phy_copper(struct e1000_hw *hw); +void e1000_power_down_phy_copper(struct e1000_hw *hw); +s32 e1000_read_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 *data); +s32 e1000_write_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 data); + +#define E1000_MAX_PHY_ADDR 4 + +/* IGP01E1000 Specific Registers */ +#define IGP01E1000_PHY_PORT_CONFIG 0x10 /* Port Config */ +#define IGP01E1000_PHY_PORT_STATUS 0x11 /* Status */ +#define IGP01E1000_PHY_PORT_CTRL 0x12 /* Control */ +#define IGP01E1000_PHY_LINK_HEALTH 0x13 /* PHY Link Health */ +#define IGP01E1000_GMII_FIFO 0x14 /* GMII FIFO */ +#define IGP01E1000_PHY_CHANNEL_QUALITY 0x15 /* PHY Channel Quality */ +#define IGP02E1000_PHY_POWER_MGMT 0x19 /* Power Management */ +#define IGP01E1000_PHY_PAGE_SELECT 0x1F /* Page Select */ +#define BM_PHY_PAGE_SELECT 22 /* Page Select for BM */ +#define IGP_PAGE_SHIFT 5 +#define PHY_REG_MASK 0x1F + +#define BM_WUC_PAGE 800 +#define BM_WUC_ADDRESS_OPCODE 0x11 +#define BM_WUC_DATA_OPCODE 0x12 +#define BM_WUC_ENABLE_PAGE 769 +#define BM_WUC_ENABLE_REG 17 +#define BM_WUC_ENABLE_BIT (1 << 2) +#define BM_WUC_HOST_WU_BIT (1 << 4) + +/* BM PHY Copper Specific Control 1 */ +#define BM_CS_CTRL1 16 +#define BM_CS_CTRL1_ENERGY_DETECT 0x0300 /* Enable Energy Detect */ + +/* BM PHY Copper Specific States */ +#define BM_CS_STATUS 17 +#define BM_CS_STATUS_ENERGY_DETECT 0x0010 /* Energy Detect Status */ + +#define IGP01E1000_PHY_PCS_INIT_REG 0x00B4 +#define IGP01E1000_PHY_POLARITY_MASK 0x0078 + +#define IGP01E1000_PSCR_AUTO_MDIX 0x1000 +#define IGP01E1000_PSCR_FORCE_MDI_MDIX 0x2000 /* 0=MDI, 1=MDIX */ + +#define IGP01E1000_PSCFR_SMART_SPEED 0x0080 + +/* Enable flexible speed on link-up */ +#define IGP01E1000_GMII_FLEX_SPD 0x0010 +#define IGP01E1000_GMII_SPD 0x0020 /* Enable SPD */ + +#define IGP02E1000_PM_SPD 0x0001 /* Smart Power Down */ +#define IGP02E1000_PM_D0_LPLU 0x0002 /* For D0a states */ +#define IGP02E1000_PM_D3_LPLU 0x0004 /* For all other states */ + +#define IGP01E1000_PLHR_SS_DOWNGRADE 0x8000 + +#define IGP01E1000_PSSR_POLARITY_REVERSED 0x0002 +#define IGP01E1000_PSSR_MDIX 0x0008 +#define IGP01E1000_PSSR_SPEED_MASK 0xC000 +#define IGP01E1000_PSSR_SPEED_1000MBPS 0xC000 + +#define IGP02E1000_PHY_CHANNEL_NUM 4 +#define IGP02E1000_PHY_AGC_A 0x11B1 +#define IGP02E1000_PHY_AGC_B 0x12B1 +#define IGP02E1000_PHY_AGC_C 0x14B1 +#define IGP02E1000_PHY_AGC_D 0x18B1 + +#define IGP02E1000_AGC_LENGTH_SHIFT 9 /* Course - 15:13, Fine - 12:9 */ +#define IGP02E1000_AGC_LENGTH_MASK 0x7F +#define IGP02E1000_AGC_RANGE 15 + +#define IGP03E1000_PHY_MISC_CTRL 0x1B +#define IGP03E1000_PHY_MISC_DUPLEX_MANUAL_SET 0x1000 /* Manually Set Duplex */ + +#define E1000_CABLE_LENGTH_UNDEFINED 0xFF + +#define E1000_KMRNCTRLSTA_OFFSET 0x001F0000 +#define E1000_KMRNCTRLSTA_OFFSET_SHIFT 16 +#define E1000_KMRNCTRLSTA_REN 0x00200000 +#define E1000_KMRNCTRLSTA_DIAG_OFFSET 0x3 /* Kumeran Diagnostic */ +#define E1000_KMRNCTRLSTA_DIAG_NELPBK 0x1000 /* Nearend Loopback mode */ + +#define IFE_PHY_EXTENDED_STATUS_CONTROL 0x10 +#define IFE_PHY_SPECIAL_CONTROL 0x11 /* 100BaseTx PHY Special Control */ +#define IFE_PHY_SPECIAL_CONTROL_LED 0x1B /* PHY Special and LED Control */ +#define IFE_PHY_MDIX_CONTROL 0x1C /* MDI/MDI-X Control */ + +/* IFE PHY Extended Status Control */ +#define IFE_PESC_POLARITY_REVERSED 0x0100 + +/* IFE PHY Special Control */ +#define IFE_PSC_AUTO_POLARITY_DISABLE 0x0010 +#define IFE_PSC_FORCE_POLARITY 0x0020 +#define IFE_PSC_DISABLE_DYNAMIC_POWER_DOWN 0x0100 + +/* IFE PHY Special Control and LED Control */ +#define IFE_PSCL_PROBE_MODE 0x0020 +#define IFE_PSCL_PROBE_LEDS_OFF 0x0006 /* Force LEDs 0 and 2 off */ +#define IFE_PSCL_PROBE_LEDS_ON 0x0007 /* Force LEDs 0 and 2 on */ + +/* IFE PHY MDIX Control */ +#define IFE_PMC_MDIX_STATUS 0x0020 /* 1=MDI-X, 0=MDI */ +#define IFE_PMC_FORCE_MDIX 0x0040 /* 1=force MDI-X, 0=force MDI */ +#define IFE_PMC_AUTO_MDIX 0x0080 /* 1=enable auto MDI/MDI-X, 0=disable */ + +#endif diff --git a/sys/dev/netif/ig_hal/e1000_regs.h b/sys/dev/netif/ig_hal/e1000_regs.h new file mode 100644 index 0000000000..1dbd56bb5d --- /dev/null +++ b/sys/dev/netif/ig_hal/e1000_regs.h @@ -0,0 +1,498 @@ +/****************************************************************************** + + Copyright (c) 2001-2008, Intel Corporation + All rights reserved. + + Redistribution and use in source and binary forms, with or without + modification, are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, + this list of conditions and the following disclaimer. + + 2. Redistributions in binary form must reproduce the above copyright + notice, this list of conditions and the following disclaimer in the + documentation and/or other materials provided with the distribution. + + 3. Neither the name of the Intel Corporation nor the names of its + contributors may be used to endorse or promote products derived from + this software without specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE + ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE + LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR + CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF + SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS + INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN + CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) + ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + POSSIBILITY OF SUCH DAMAGE. + +******************************************************************************/ +/*$FreeBSD$*/ + +#ifndef _E1000_REGS_H_ +#define _E1000_REGS_H_ + +#define E1000_CTRL 0x00000 /* Device Control - RW */ +#define E1000_CTRL_DUP 0x00004 /* Device Control Duplicate (Shadow) - RW */ +#define E1000_STATUS 0x00008 /* Device Status - RO */ +#define E1000_EECD 0x00010 /* EEPROM/Flash Control - RW */ +#define E1000_EERD 0x00014 /* EEPROM Read - RW */ +#define E1000_CTRL_EXT 0x00018 /* Extended Device Control - RW */ +#define E1000_FLA 0x0001C /* Flash Access - RW */ +#define E1000_MDIC 0x00020 /* MDI Control - RW */ +#define E1000_SCTL 0x00024 /* SerDes Control - RW */ +#define E1000_FCAL 0x00028 /* Flow Control Address Low - RW */ +#define E1000_FCAH 0x0002C /* Flow Control Address High -RW */ +#define E1000_FEXT 0x0002C /* Future Extended - RW */ +#define E1000_FEXTNVM 0x00028 /* Future Extended NVM - RW */ +#define E1000_FCT 0x00030 /* Flow Control Type - RW */ +#define E1000_CONNSW 0x00034 /* Copper/Fiber switch control - RW */ +#define E1000_VET 0x00038 /* VLAN Ether Type - RW */ +#define E1000_ICR 0x000C0 /* Interrupt Cause Read - R/clr */ +#define E1000_ITR 0x000C4 /* Interrupt Throttling Rate - RW */ +#define E1000_ICS 0x000C8 /* Interrupt Cause Set - WO */ +#define E1000_IMS 0x000D0 /* Interrupt Mask Set - RW */ +#define E1000_IMC 0x000D8 /* Interrupt Mask Clear - WO */ +#define E1000_IAM 0x000E0 /* Interrupt Acknowledge Auto Mask */ +#define E1000_IVAR 0x000E4 /* Interrupt Vector Allocation Register - RW */ +#define E1000_RCTL 0x00100 /* Rx Control - RW */ +#define E1000_FCTTV 0x00170 /* Flow Control Transmit Timer Value - RW */ +#define E1000_TXCW 0x00178 /* Tx Configuration Word - RW */ +#define E1000_RXCW 0x00180 /* Rx Configuration Word - RO */ +#define E1000_EICR 0x01580 /* Ext. Interrupt Cause Read - R/clr */ +#define E1000_EITR(_n) (0x01680 + (0x4 * (_n))) +#define E1000_EICS 0x01520 /* Ext. Interrupt Cause Set - W0 */ +#define E1000_EIMS 0x01524 /* Ext. Interrupt Mask Set/Read - RW */ +#define E1000_EIMC 0x01528 /* Ext. Interrupt Mask Clear - WO */ +#define E1000_EIAC 0x0152C /* Ext. Interrupt Auto Clear - RW */ +#define E1000_EIAM 0x01530 /* Ext. Interrupt Ack Auto Clear Mask - RW */ +#define E1000_GPIE 0x01514 /* General Purpose Interrupt Enable - RW */ +#define E1000_IVAR0 0x01700 /* Interrupt Vector Allocation (array) - RW */ +#define E1000_IVAR_MISC 0x01740 /* IVAR for "other" causes - RW */ +#define E1000_TCTL 0x00400 /* Tx Control - RW */ +#define E1000_TCTL_EXT 0x00404 /* Extended Tx Control - RW */ +#define E1000_TIPG 0x00410 /* Tx Inter-packet gap -RW */ +#define E1000_TBT 0x00448 /* Tx Burst Timer - RW */ +#define E1000_AIT 0x00458 /* Adaptive Interframe Spacing Throttle - RW */ +#define E1000_LEDCTL 0x00E00 /* LED Control - RW */ +#define E1000_EXTCNF_CTRL 0x00F00 /* Extended Configuration Control */ +#define E1000_EXTCNF_SIZE 0x00F08 /* Extended Configuration Size */ +#define E1000_PHY_CTRL 0x00F10 /* PHY Control Register in CSR */ +#define E1000_PBA 0x01000 /* Packet Buffer Allocation - RW */ +#define E1000_PBS 0x01008 /* Packet Buffer Size */ +#define E1000_EEMNGCTL 0x01010 /* MNG EEprom Control */ +#define E1000_EEARBC 0x01024 /* EEPROM Auto Read Bus Control */ +#define E1000_FLASHT 0x01028 /* FLASH Timer Register */ +#define E1000_EEWR 0x0102C /* EEPROM Write Register - RW */ +#define E1000_FLSWCTL 0x01030 /* FLASH control register */ +#define E1000_FLSWDATA 0x01034 /* FLASH data register */ +#define E1000_FLSWCNT 0x01038 /* FLASH Access Counter */ +#define E1000_FLOP 0x0103C /* FLASH Opcode Register */ +#define E1000_I2CCMD 0x01028 /* SFPI2C Command Register - RW */ +#define E1000_I2CPARAMS 0x0102C /* SFPI2C Parameters Register - RW */ +#define E1000_WDSTP 0x01040 /* Watchdog Setup - RW */ +#define E1000_SWDSTS 0x01044 /* SW Device Status - RW */ +#define E1000_FRTIMER 0x01048 /* Free Running Timer - RW */ +#define E1000_TCPTIMER 0x0104C /* TCP Timer - RW */ +#define E1000_VPDDIAG 0x01060 /* VPD Diagnostic - RO */ +#define E1000_ICR_V2 0x01500 /* Interrupt Cause - new location - RC */ +#define E1000_ICS_V2 0x01504 /* Interrupt Cause Set - new location - WO */ +#define E1000_IMS_V2 0x01508 /* Interrupt Mask Set/Read - new location - RW */ +#define E1000_IMC_V2 0x0150C /* Interrupt Mask Clear - new location - WO */ +#define E1000_IAM_V2 0x01510 /* Interrupt Ack Auto Mask - new location - RW */ +#define E1000_ERT 0x02008 /* Early Rx Threshold - RW */ +#define E1000_FCRTL 0x02160 /* Flow Control Receive Threshold Low - RW */ +#define E1000_FCRTH 0x02168 /* Flow Control Receive Threshold High - RW */ +#define E1000_PSRCTL 0x02170 /* Packet Split Receive Control - RW */ +#define E1000_RDFPCQ(_n) (0x02430 + (0x4 * (_n))) +#define E1000_PBRTH 0x02458 /* PB Rx Arbitration Threshold - RW */ +#define E1000_FCRTV 0x02460 /* Flow Control Refresh Timer Value - RW */ +/* Split and Replication Rx Control - RW */ +#define E1000_RDPUMB 0x025CC /* DMA Rx Descriptor uC Mailbox - RW */ +#define E1000_RDPUAD 0x025D0 /* DMA Rx Descriptor uC Addr Command - RW */ +#define E1000_RDPUWD 0x025D4 /* DMA Rx Descriptor uC Data Write - RW */ +#define E1000_RDPURD 0x025D8 /* DMA Rx Descriptor uC Data Read - RW */ +#define E1000_RDPUCTL 0x025DC /* DMA Rx Descriptor uC Control - RW */ +#define E1000_PBDIAG 0x02458 /* Packet Buffer Diagnostic - RW */ +#define E1000_RXPBS 0x02404 /* Rx Packet Buffer Size - RW */ +#define E1000_RXCTL(_n) (0x0C014 + (0x40 * (_n))) +#define E1000_RQDPC(_n) (0x0C030 + (0x40 * (_n))) +#define E1000_TXCTL(_n) (0x0E014 + (0x40 * (_n))) +#define E1000_RXCTL(_n) (0x0C014 + (0x40 * (_n))) +#define E1000_RQDPC(_n) (0x0C030 + (0x40 * (_n))) +#define E1000_RDTR 0x02820 /* Rx Delay Timer - RW */ +#define E1000_RADV 0x0282C /* Rx Interrupt Absolute Delay Timer - RW */ +/* + * Convenience macros + * + * Note: "_n" is the queue number of the register to be written to. + * + * Example usage: + * E1000_RDBAL_REG(current_rx_queue) + */ +#define E1000_RDBAL(_n) ((_n) < 4 ? (0x02800 + ((_n) * 0x100)) : \ + (0x0C000 + ((_n) * 0x40))) +#define E1000_RDBAH(_n) ((_n) < 4 ? (0x02804 + ((_n) * 0x100)) : \ + (0x0C004 + ((_n) * 0x40))) +#define E1000_RDLEN(_n) ((_n) < 4 ? (0x02808 + ((_n) * 0x100)) : \ + (0x0C008 + ((_n) * 0x40))) +#define E1000_SRRCTL(_n) ((_n) < 4 ? (0x0280C + ((_n) * 0x100)) : \ + (0x0C00C + ((_n) * 0x40))) +#define E1000_RDH(_n) ((_n) < 4 ? (0x02810 + ((_n) * 0x100)) : \ + (0x0C010 + ((_n) * 0x40))) +#define E1000_RDT(_n) ((_n) < 4 ? (0x02818 + ((_n) * 0x100)) : \ + (0x0C018 + ((_n) * 0x40))) +#define E1000_RXDCTL(_n) ((_n) < 4 ? (0x02828 + ((_n) * 0x100)) : \ + (0x0C028 + ((_n) * 0x40))) +#define E1000_TDBAL(_n) ((_n) < 4 ? (0x03800 + ((_n) * 0x100)) : \ + (0x0E000 + ((_n) * 0x40))) +#define E1000_TDBAH(_n) ((_n) < 4 ? (0x03804 + ((_n) * 0x100)) : \ + (0x0E004 + ((_n) * 0x40))) +#define E1000_TDLEN(_n) ((_n) < 4 ? (0x03808 + ((_n) * 0x100)) : \ + (0x0E008 + ((_n) * 0x40))) +#define E1000_TDH(_n) ((_n) < 4 ? (0x03810 + ((_n) * 0x100)) : \ + (0x0E010 + ((_n) * 0x40))) +#define E1000_TDT(_n) ((_n) < 4 ? (0x03818 + ((_n) * 0x100)) : \ + (0x0E018 + ((_n) * 0x40))) +#define E1000_TXDCTL(_n) ((_n) < 4 ? (0x03828 + ((_n) * 0x100)) : \ + (0x0E028 + ((_n) * 0x40))) +#define E1000_TARC(_n) (0x03840 + (_n << 8)) +#define E1000_DCA_TXCTRL(_n) (0x03814 + (_n << 8)) +#define E1000_DCA_RXCTRL(_n) (0x02814 + (_n << 8)) +#define E1000_TDWBAL(_n) ((_n) < 4 ? (0x03838 + ((_n) * 0x100)) : \ + (0x0E038 + ((_n) * 0x40))) +#define E1000_TDWBAH(_n) ((_n) < 4 ? (0x0383C + ((_n) * 0x100)) : \ + (0x0E03C + ((_n) * 0x40))) +#define E1000_RSRPD 0x02C00 /* Rx Small Packet Detect - RW */ +#define E1000_RAID 0x02C08 /* Receive Ack Interrupt Delay - RW */ +#define E1000_TXDMAC 0x03000 /* Tx DMA Control - RW */ +#define E1000_KABGTXD 0x03004 /* AFE Band Gap Transmit Ref Data */ +#define E1000_PSRTYPE(_i) (0x05480 + ((_i) * 4)) +#define E1000_RAL(_i) (((_i) <= 15) ? (0x05400 + ((_i) * 8)) : \ + (0x054E0 + ((_i - 16) * 8))) +#define E1000_RAH(_i) (((_i) <= 15) ? (0x05404 + ((_i) * 8)) : \ + (0x054E4 + ((_i - 16) * 8))) +#define E1000_IP4AT_REG(_i) (0x05840 + ((_i) * 8)) +#define E1000_IP6AT_REG(_i) (0x05880 + ((_i) * 4)) +#define E1000_WUPM_REG(_i) (0x05A00 + ((_i) * 4)) +#define E1000_FFMT_REG(_i) (0x09000 + ((_i) * 8)) +#define E1000_FFVT_REG(_i) (0x09800 + ((_i) * 8)) +#define E1000_FFLT_REG(_i) (0x05F00 + ((_i) * 8)) +#define E1000_PBSLAC 0x03100 /* Packet Buffer Slave Access Control */ +#define E1000_PBSLAD(_n) (0x03110 + (0x4 * (_n))) /* Packet Buffer DWORD (_n) */ +#define E1000_TXPBS 0x03404 /* Tx Packet Buffer Size - RW */ +#define E1000_TDFH 0x03410 /* Tx Data FIFO Head - RW */ +#define E1000_TDFT 0x03418 /* Tx Data FIFO Tail - RW */ +#define E1000_TDFHS 0x03420 /* Tx Data FIFO Head Saved - RW */ +#define E1000_TDFTS 0x03428 /* Tx Data FIFO Tail Saved - RW */ +#define E1000_TDFPC 0x03430 /* Tx Data FIFO Packet Count - RW */ +#define E1000_TDPUMB 0x0357C /* DMA Tx Descriptor uC Mail Box - RW */ +#define E1000_TDPUAD 0x03580 /* DMA Tx Descriptor uC Addr Command - RW */ +#define E1000_TDPUWD 0x03584 /* DMA Tx Descriptor uC Data Write - RW */ +#define E1000_TDPURD 0x03588 /* DMA Tx Descriptor uC Data Read - RW */ +#define E1000_TDPUCTL 0x0358C /* DMA Tx Descriptor uC Control - RW */ +#define E1000_DTXCTL 0x03590 /* DMA Tx Control - RW */ +#define E1000_DTXTCPFLGL 0x0359C /* DMA Tx Control flag low - RW */ +#define E1000_DTXTCPFLGH 0x035A0 /* DMA Tx Control flag high - RW */ +#define E1000_DTXMXSZRQ 0x03540 /* DMA Tx Max Total Allow Size Requests - RW */ +#define E1000_TIDV 0x03820 /* Tx Interrupt Delay Value - RW */ +#define E1000_TADV 0x0382C /* Tx Interrupt Absolute Delay Val - RW */ +#define E1000_TSPMT 0x03830 /* TCP Segmentation PAD & Min Threshold - RW */ +#define E1000_CRCERRS 0x04000 /* CRC Error Count - R/clr */ +#define E1000_ALGNERRC 0x04004 /* Alignment Error Count - R/clr */ +#define E1000_SYMERRS 0x04008 /* Symbol Error Count - R/clr */ +#define E1000_RXERRC 0x0400C /* Receive Error Count - R/clr */ +#define E1000_MPC 0x04010 /* Missed Packet Count - R/clr */ +#define E1000_SCC 0x04014 /* Single Collision Count - R/clr */ +#define E1000_ECOL 0x04018 /* Excessive Collision Count - R/clr */ +#define E1000_MCC 0x0401C /* Multiple Collision Count - R/clr */ +#define E1000_LATECOL 0x04020 /* Late Collision Count - R/clr */ +#define E1000_COLC 0x04028 /* Collision Count - R/clr */ +#define E1000_DC 0x04030 /* Defer Count - R/clr */ +#define E1000_TNCRS 0x04034 /* Tx-No CRS - R/clr */ +#define E1000_SEC 0x04038 /* Sequence Error Count - R/clr */ +#define E1000_CEXTERR 0x0403C /* Carrier Extension Error Count - R/clr */ +#define E1000_RLEC 0x04040 /* Receive Length Error Count - R/clr */ +#define E1000_XONRXC 0x04048 /* XON Rx Count - R/clr */ +#define E1000_XONTXC 0x0404C /* XON Tx Count - R/clr */ +#define E1000_XOFFRXC 0x04050 /* XOFF Rx Count - R/clr */ +#define E1000_XOFFTXC 0x04054 /* XOFF Tx Count - R/clr */ +#define E1000_FCRUC 0x04058 /* Flow Control Rx Unsupported Count- R/clr */ +#define E1000_PRC64 0x0405C /* Packets Rx (64 bytes) - R/clr */ +#define E1000_PRC127 0x04060 /* Packets Rx (65-127 bytes) - R/clr */ +#define E1000_PRC255 0x04064 /* Packets Rx (128-255 bytes) - R/clr */ +#define E1000_PRC511 0x04068 /* Packets Rx (255-511 bytes) - R/clr */ +#define E1000_PRC1023 0x0406C /* Packets Rx (512-1023 bytes) - R/clr */ +#define E1000_PRC1522 0x04070 /* Packets Rx (1024-1522 bytes) - R/clr */ +#define E1000_GPRC 0x04074 /* Good Packets Rx Count - R/clr */ +#define E1000_BPRC 0x04078 /* Broadcast Packets Rx Count - R/clr */ +#define E1000_MPRC 0x0407C /* Multicast Packets Rx Count - R/clr */ +#define E1000_GPTC 0x04080 /* Good Packets Tx Count - R/clr */ +#define E1000_GORCL 0x04088 /* Good Octets Rx Count Low - R/clr */ +#define E1000_GORCH 0x0408C /* Good Octets Rx Count High - R/clr */ +#define E1000_GOTCL 0x04090 /* Good Octets Tx Count Low - R/clr */ +#define E1000_GOTCH 0x04094 /* Good Octets Tx Count High - R/clr */ +#define E1000_RNBC 0x040A0 /* Rx No Buffers Count - R/clr */ +#define E1000_RUC 0x040A4 /* Rx Undersize Count - R/clr */ +#define E1000_RFC 0x040A8 /* Rx Fragment Count - R/clr */ +#define E1000_ROC 0x040AC /* Rx Oversize Count - R/clr */ +#define E1000_RJC 0x040B0 /* Rx Jabber Count - R/clr */ +#define E1000_MGTPRC 0x040B4 /* Management Packets Rx Count - R/clr */ +#define E1000_MGTPDC 0x040B8 /* Management Packets Dropped Count - R/clr */ +#define E1000_MGTPTC 0x040BC /* Management Packets Tx Count - R/clr */ +#define E1000_TORL 0x040C0 /* Total Octets Rx Low - R/clr */ +#define E1000_TORH 0x040C4 /* Total Octets Rx High - R/clr */ +#define E1000_TOTL 0x040C8 /* Total Octets Tx Low - R/clr */ +#define E1000_TOTH 0x040CC /* Total Octets Tx High - R/clr */ +#define E1000_TPR 0x040D0 /* Total Packets Rx - R/clr */ +#define E1000_TPT 0x040D4 /* Total Packets Tx - R/clr */ +#define E1000_PTC64 0x040D8 /* Packets Tx (64 bytes) - R/clr */ +#define E1000_PTC127 0x040DC /* Packets Tx (65-127 bytes) - R/clr */ +#define E1000_PTC255 0x040E0 /* Packets Tx (128-255 bytes) - R/clr */ +#define E1000_PTC511 0x040E4 /* Packets Tx (256-511 bytes) - R/clr */ +#define E1000_PTC1023 0x040E8 /* Packets Tx (512-1023 bytes) - R/clr */ +#define E1000_PTC1522 0x040EC /* Packets Tx (1024-1522 Bytes) - R/clr */ +#define E1000_MPTC 0x040F0 /* Multicast Packets Tx Count - R/clr */ +#define E1000_BPTC 0x040F4 /* Broadcast Packets Tx Count - R/clr */ +#define E1000_TSCTC 0x040F8 /* TCP Segmentation Context Tx - R/clr */ +#define E1000_TSCTFC 0x040FC /* TCP Segmentation Context Tx Fail - R/clr */ +#define E1000_IAC 0x04100 /* Interrupt Assertion Count */ +#define E1000_ICRXPTC 0x04104 /* Interrupt Cause Rx Pkt Timer Expire Count */ +#define E1000_ICRXATC 0x04108 /* Interrupt Cause Rx Abs Timer Expire Count */ +#define E1000_ICTXPTC 0x0410C /* Interrupt Cause Tx Pkt Timer Expire Count */ +#define E1000_ICTXATC 0x04110 /* Interrupt Cause Tx Abs Timer Expire Count */ +#define E1000_ICTXQEC 0x04118 /* Interrupt Cause Tx Queue Empty Count */ +#define E1000_ICTXQMTC 0x0411C /* Interrupt Cause Tx Queue Min Thresh Count */ +#define E1000_ICRXDMTC 0x04120 /* Interrupt Cause Rx Desc Min Thresh Count */ +#define E1000_ICRXOC 0x04124 /* Interrupt Cause Receiver Overrun Count */ + +#define E1000_VFGPRC 0x00F10 +#define E1000_VFGORC 0x00F18 +#define E1000_VFMPRC 0x00F3C +#define E1000_VFGPTC 0x00F14 +#define E1000_VFGOTC 0x00F34 +#define E1000_VFGOTLBC 0x00F50 +#define E1000_VFGPTLBC 0x00F44 +#define E1000_VFGORLBC 0x00F48 +#define E1000_VFGPRLBC 0x00F40 +#define E1000_LSECTXUT 0x04300 /* LinkSec Tx Untagged Packet Count - OutPktsUntagged */ +#define E1000_LSECTXPKTE 0x04304 /* LinkSec Encrypted Tx Packets Count - OutPktsEncrypted */ +#define E1000_LSECTXPKTP 0x04308 /* LinkSec Protected Tx Packet Count - OutPktsProtected */ +#define E1000_LSECTXOCTE 0x0430C /* LinkSec Encrypted Tx Octets Count - OutOctetsEncrypted */ +#define E1000_LSECTXOCTP 0x04310 /* LinkSec Protected Tx Octets Count - OutOctetsProtected */ +#define E1000_LSECRXUT 0x04314 /* LinkSec Untagged non-Strict Rx Packet Count - InPktsUntagged/InPktsNoTag */ +#define E1000_LSECRXOCTD 0x0431C /* LinkSec Rx Octets Decrypted Count - InOctetsDecrypted */ +#define E1000_LSECRXOCTV 0x04320 /* LinkSec Rx Octets Validated - InOctetsValidated */ +#define E1000_LSECRXBAD 0x04324 /* LinkSec Rx Bad Tag - InPktsBadTag */ +#define E1000_LSECRXNOSCI 0x04328 /* LinkSec Rx Packet No SCI Count - InPktsNoSci */ +#define E1000_LSECRXUNSCI 0x0432C /* LinkSec Rx Packet Unknown SCI Count - InPktsUnknownSci */ +#define E1000_LSECRXUNCH 0x04330 /* LinkSec Rx Unchecked Packets Count - InPktsUnchecked */ +#define E1000_LSECRXDELAY 0x04340 /* LinkSec Rx Delayed Packet Count - InPktsDelayed */ +#define E1000_LSECRXLATE 0x04350 /* LinkSec Rx Late Packets Count - InPktsLate */ +#define E1000_LSECRXOK(_n) (0x04360 + (0x04 * (_n))) /* LinkSec Rx Packet OK Count - InPktsOk */ +#define E1000_LSECRXINV(_n) (0x04380 + (0x04 * (_n))) /* LinkSec Rx Invalid Count - InPktsInvalid */ +#define E1000_LSECRXNV(_n) (0x043A0 + (0x04 * (_n))) /* LinkSec Rx Not Valid Count - InPktsNotValid */ +#define E1000_LSECRXUNSA 0x043C0 /* LinkSec Rx Unused SA Count - InPktsUnusedSa */ +#define E1000_LSECRXNUSA 0x043D0 /* LinkSec Rx Not Using SA Count - InPktsNotUsingSa */ +#define E1000_LSECTXCAP 0x0B000 /* LinkSec Tx Capabilities Register - RO */ +#define E1000_LSECRXCAP 0x0B300 /* LinkSec Rx Capabilities Register - RO */ +#define E1000_LSECTXCTRL 0x0B004 /* LinkSec Tx Control - RW */ +#define E1000_LSECRXCTRL 0x0B304 /* LinkSec Rx Control - RW */ +#define E1000_LSECTXSCL 0x0B008 /* LinkSec Tx SCI Low - RW */ +#define E1000_LSECTXSCH 0x0B00C /* LinkSec Tx SCI High - RW */ +#define E1000_LSECTXSA 0x0B010 /* LinkSec Tx SA0 - RW */ +#define E1000_LSECTXPN0 0x0B018 /* LinkSec Tx SA PN 0 - RW */ +#define E1000_LSECTXPN1 0x0B01C /* LinkSec Tx SA PN 1 - RW */ +#define E1000_LSECRXSCL 0x0B3D0 /* LinkSec Rx SCI Low - RW */ +#define E1000_LSECRXSCH 0x0B3E0 /* LinkSec Rx SCI High - RW */ +#define E1000_LSECTXKEY0(_n) (0x0B020 + (0x04 * (_n))) /* LinkSec Tx 128-bit Key 0 - WO */ +#define E1000_LSECTXKEY1(_n) (0x0B030 + (0x04 * (_n))) /* LinkSec Tx 128-bit Key 1 - WO */ +#define E1000_LSECRXSA(_n) (0x0B310 + (0x04 * (_n))) /* LinkSec Rx SAs - RW */ +#define E1000_LSECRXPN(_n) (0x0B330 + (0x04 * (_n))) /* LinkSec Rx SAs - RW */ +/* + * LinkSec Rx Keys - where _n is the SA no. and _m the 4 dwords of the 128 bit + * key - RW. + */ +#define E1000_LSECRXKEY(_n, _m) (0x0B350 + (0x10 * (_n)) + (0x04 * (_m))) + +#define E1000_SSVPC 0x041A0 /* Switch Security Violation Packet Count */ +#define E1000_IPSCTRL 0xB430 /* IpSec Control Register */ +#define E1000_IPSRXCMD 0x0B408 /* IPSec Rx Command Register - RW */ +#define E1000_IPSRXIDX 0x0B400 /* IPSec Rx Index - RW */ +#define E1000_IPSRXIPADDR(_n) (0x0B420+ (0x04 * (_n))) /* IPSec Rx IPv4/v6 Address - RW */ +#define E1000_IPSRXKEY(_n) (0x0B410 + (0x04 * (_n))) /* IPSec Rx 128-bit Key - RW */ +#define E1000_IPSRXSALT 0x0B404 /* IPSec Rx Salt - RW */ +#define E1000_IPSRXSPI 0x0B40C /* IPSec Rx SPI - RW */ +#define E1000_IPSTXKEY(_n) (0x0B460 + (0x04 * (_n))) /* IPSec Tx 128-bit Key - RW */ +#define E1000_IPSTXSALT 0x0B454 /* IPSec Tx Salt - RW */ +#define E1000_IPSTXIDX 0x0B450 /* IPSec Tx SA IDX - RW */ +#define E1000_PCS_CFG0 0x04200 /* PCS Configuration 0 - RW */ +#define E1000_PCS_LCTL 0x04208 /* PCS Link Control - RW */ +#define E1000_PCS_LSTAT 0x0420C /* PCS Link Status - RO */ +#define E1000_CBTMPC 0x0402C /* Circuit Breaker Tx Packet Count */ +#define E1000_HTDPMC 0x0403C /* Host Transmit Discarded Packets */ +#define E1000_CBRDPC 0x04044 /* Circuit Breaker Rx Dropped Count */ +#define E1000_CBRMPC 0x040FC /* Circuit Breaker Rx Packet Count */ +#define E1000_RPTHC 0x04104 /* Rx Packets To Host */ +#define E1000_HGPTC 0x04118 /* Host Good Packets Tx Count */ +#define E1000_HTCBDPC 0x04124 /* Host Tx Circuit Breaker Dropped Count */ +#define E1000_HGORCL 0x04128 /* Host Good Octets Received Count Low */ +#define E1000_HGORCH 0x0412C /* Host Good Octets Received Count High */ +#define E1000_HGOTCL 0x04130 /* Host Good Octets Transmit Count Low */ +#define E1000_HGOTCH 0x04134 /* Host Good Octets Transmit Count High */ +#define E1000_LENERRS 0x04138 /* Length Errors Count */ +#define E1000_SCVPC 0x04228 /* SerDes/SGMII Code Violation Pkt Count */ +#define E1000_HRMPC 0x0A018 /* Header Redirection Missed Packet Count */ +#define E1000_PCS_ANADV 0x04218 /* AN advertisement - RW */ +#define E1000_PCS_LPAB 0x0421C /* Link Partner Ability - RW */ +#define E1000_PCS_NPTX 0x04220 /* AN Next Page Transmit - RW */ +#define E1000_PCS_LPABNP 0x04224 /* Link Partner Ability Next Page - RW */ +#define E1000_1GSTAT_RCV 0x04228 /* 1GSTAT Code Violation Packet Count - RW */ +#define E1000_RXCSUM 0x05000 /* Rx Checksum Control - RW */ +#define E1000_RLPML 0x05004 /* Rx Long Packet Max Length */ +#define E1000_RFCTL 0x05008 /* Receive Filter Control*/ +#define E1000_MTA 0x05200 /* Multicast Table Array - RW Array */ +#define E1000_RA 0x05400 /* Receive Address - RW Array */ +#define E1000_RA2 0x054E0 /* 2nd half of receive address array - RW Array */ +#define E1000_VFTA 0x05600 /* VLAN Filter Table Array - RW Array */ +#define E1000_VT_CTL 0x0581C /* VMDq Control - RW */ +#define E1000_VFQA0 0x0B000 /* VLAN Filter Queue Array 0 - RW Array */ +#define E1000_VFQA1 0x0B200 /* VLAN Filter Queue Array 1 - RW Array */ +#define E1000_WUC 0x05800 /* Wakeup Control - RW */ +#define E1000_WUFC 0x05808 /* Wakeup Filter Control - RW */ +#define E1000_WUS 0x05810 /* Wakeup Status - RO */ +#define E1000_MANC 0x05820 /* Management Control - RW */ +#define E1000_IPAV 0x05838 /* IP Address Valid - RW */ +#define E1000_IP4AT 0x05840 /* IPv4 Address Table - RW Array */ +#define E1000_IP6AT 0x05880 /* IPv6 Address Table - RW Array */ +#define E1000_WUPL 0x05900 /* Wakeup Packet Length - RW */ +#define E1000_WUPM 0x05A00 /* Wakeup Packet Memory - RO A */ +#define E1000_PBACL 0x05B68 /* MSIx PBA Clear - Read/Write 1's to clear */ +#define E1000_FFLT 0x05F00 /* Flexible Filter Length Table - RW Array */ +#define E1000_HOST_IF 0x08800 /* Host Interface */ +#define E1000_FFMT 0x09000 /* Flexible Filter Mask Table - RW Array */ +#define E1000_FFVT 0x09800 /* Flexible Filter Value Table - RW Array */ +#define E1000_FHFT(_n) (0x09000 + (_n * 0x100)) /* Flexible Host Filter Table */ +#define E1000_FHFT_EXT(_n) (0x09A00 + (_n * 0x100)) /* Ext Flexible Host Filter Table */ + + +#define E1000_KMRNCTRLSTA 0x00034 /* MAC-PHY interface - RW */ +#define E1000_MDPHYA 0x0003C /* PHY address - RW */ +#define E1000_MANC2H 0x05860 /* Management Control To Host - RW */ +#define E1000_SW_FW_SYNC 0x05B5C /* Software-Firmware Synchronization - RW */ +#define E1000_CCMCTL 0x05B48 /* CCM Control Register */ +#define E1000_GIOCTL 0x05B44 /* GIO Analog Control Register */ +#define E1000_SCCTL 0x05B4C /* PCIc PLL Configuration Register */ +#define E1000_GCR 0x05B00 /* PCI-Ex Control */ +#define E1000_GSCL_1 0x05B10 /* PCI-Ex Statistic Control #1 */ +#define E1000_GSCL_2 0x05B14 /* PCI-Ex Statistic Control #2 */ +#define E1000_GSCL_3 0x05B18 /* PCI-Ex Statistic Control #3 */ +#define E1000_GSCL_4 0x05B1C /* PCI-Ex Statistic Control #4 */ +#define E1000_FACTPS 0x05B30 /* Function Active and Power State to MNG */ +#define E1000_SWSM 0x05B50 /* SW Semaphore */ +#define E1000_FWSM 0x05B54 /* FW Semaphore */ +#define E1000_DCA_ID 0x05B70 /* DCA Requester ID Information - RO */ +#define E1000_DCA_CTRL 0x05B74 /* DCA Control - RW */ +#define E1000_FFLT_DBG 0x05F04 /* Debug Register */ +#define E1000_HICR 0x08F00 /* Host Interface Control */ + +/* RSS registers */ +#define E1000_CPUVEC 0x02C10 /* CPU Vector Register - RW */ +#define E1000_MRQC 0x05818 /* Multiple Receive Control - RW */ +#define E1000_IMIR(_i) (0x05A80 + ((_i) * 4)) /* Immediate Interrupt */ +#define E1000_IMIREXT(_i) (0x05AA0 + ((_i) * 4)) /* Immediate Interrupt Ext*/ +#define E1000_IMIRVP 0x05AC0 /* Immediate Interrupt Rx VLAN Priority - RW */ +#define E1000_MSIXBM(_i) (0x01600 + ((_i) * 4)) /* MSI-X Allocation Register + * (_i) - RW */ +#define E1000_MSIXTADD(_i) (0x0C000 + ((_i) * 0x10)) /* MSI-X Table entry addr + * low reg - RW */ +#define E1000_MSIXTUADD(_i) (0x0C004 + ((_i) * 0x10)) /* MSI-X Table entry addr + * upper reg - RW */ +#define E1000_MSIXTMSG(_i) (0x0C008 + ((_i) * 0x10)) /* MSI-X Table entry + * message reg - RW */ +#define E1000_MSIXVCTRL(_i) (0x0C00C + ((_i) * 0x10)) /* MSI-X Table entry + * vector ctrl reg - RW */ +#define E1000_MSIXPBA 0x0E000 /* MSI-X Pending bit array */ +#define E1000_RETA(_i) (0x05C00 + ((_i) * 4)) /* Redirection Table - RW */ +#define E1000_RSSRK(_i) (0x05C80 + ((_i) * 4)) /* RSS Random Key - RW */ +#define E1000_RSSIM 0x05864 /* RSS Interrupt Mask */ +#define E1000_RSSIR 0x05868 /* RSS Interrupt Request */ +/* VT Registers */ +#define E1000_SWPBS 0x03004 /* Switch Packet Buffer Size - RW */ +#define E1000_MBVFICR 0x00C80 /* Mailbox VF Cause - RWC */ +#define E1000_MBVFIMR 0x00C84 /* Mailbox VF int Mask - RW */ +#define E1000_VFLRE 0x00C88 /* VF Register Events - RWC */ +#define E1000_VFRE 0x00C8C /* VF Receive Enables */ +#define E1000_VFTE 0x00C90 /* VF Transmit Enables */ +#define E1000_QDE 0x02408 /* Queue Drop Enable - RW */ +#define E1000_DTXSWC 0x03500 /* DMA Tx Switch Control - RW */ +#define E1000_VLVF 0x05D00 /* VLAN Virtual Machine Filter - RW */ +#define E1000_RPLOLR 0x05AF0 /* Replication Offload - RW */ +#define E1000_UTA 0x0A000 /* Unicast Table Array - RW */ +#define E1000_IOVTCL 0x05BBC /* IOV Control Register */ +#define E1000_VMRCTL 0X05D80 /* Virtual Mirror Rule Control */ +/* These act per VF so an array friendly macro is used */ +#define E1000_V2PMAILBOX(_n) (0x00C40 + (4 * (_n))) +#define E1000_P2VMAILBOX(_n) (0x00C00 + (4 * (_n))) +#define E1000_VMBMEM(_n) (0x00800 + (64 * (_n))) +#define E1000_VFVMBMEM(_n) (0x00800 + (_n)) +#define E1000_VMOLR(_n) (0x05AD0 + (4 * (_n))) +/* Time Sync */ +#define E1000_TSYNCRXCTL 0x0B620 /* Rx Time Sync Control register - RW */ +#define E1000_TSYNCTXCTL 0x0B614 /* Tx Time Sync Control register - RW */ +#define E1000_TSYNCRXCFG 0x05F50 /* Time Sync Rx Configuration - RW */ +#define E1000_RXSTMPL 0x0B624 /* Rx timestamp Low - RO */ +#define E1000_RXSTMPH 0x0B628 /* Rx timestamp High - RO */ +#define E1000_RXSATRL 0x0B62C /* Rx timestamp attribute low - RO */ +#define E1000_RXSATRH 0x0B630 /* Rx timestamp attribute high - RO */ +#define E1000_TXSTMPL 0x0B618 /* Tx timestamp value Low - RO */ +#define E1000_TXSTMPH 0x0B61C /* Tx timestamp value High - RO */ +#define E1000_SYSTIML 0x0B600 /* System time register Low - RO */ +#define E1000_SYSTIMH 0x0B604 /* System time register High - RO */ +#define E1000_TIMINCA 0x0B608 /* Increment attributes register - RW */ +#define E1000_RXMTRL 0x0B634 /* Time sync Rx EtherType and Msg Type - RW */ +#define E1000_RXUDP 0x0B638 /* Time Sync Rx UDP Port - RW */ + +/* Filtering Registers */ +#define E1000_SAQF(_n) (0x05980 + (4 * (_n))) /* Source Address Queue Fltr */ +#define E1000_DAQF(_n) (0x059A0 + (4 * (_n))) /* Dest Address Queue Fltr */ +#define E1000_SPQF(_n) (0x059C0 + (4 * (_n))) /* Source Port Queue Fltr */ +#define E1000_FTQF(_n) (0x059E0 + (4 * (_n))) /* 5-tuple Queue Fltr */ +#define E1000_SYNQF(_n) (0x055FC + (4 * (_n))) /* SYN Packet Queue Fltr */ +#define E1000_ETQF(_n) (0x05CB0 + (4 * (_n))) /* EType Queue Fltr */ + +#define E1000_RTTDCS 0x3600 /* Reedtown Tx Desc plane control and status */ +#define E1000_RTTPCS 0x3474 /* Reedtown Tx Packet Plane control and status */ +#define E1000_RTRPCS 0x2474 /* Rx packet plane control and status */ +#define E1000_RTRUP2TC 0x05AC4 /* Rx User Priority to Traffic Class */ +#define E1000_RTTUP2TC 0x0418 /* Transmit User Priority to Traffic Class */ +#define E1000_RTTDTCRC(_n) (0x3610 + ((_n) * 4)) /* Tx Desc plane TC Rate-scheduler config */ +#define E1000_RTTPTCRC(_n) (0x3480 + ((_n) * 4)) /* Tx Packet plane TC Rate-Scheduler Config */ +#define E1000_RTRPTCRC(_n) (0x2480 + ((_n) * 4)) /* Rx Packet plane TC Rate-Scheduler Config */ +#define E1000_RTTDTCRS(_n) (0x3630 + ((_n) * 4)) /* Tx Desc Plane TC Rate-Scheduler Status */ +#define E1000_RTTDTCRM(_n) (0x3650 + ((_n) * 4)) /* Tx Desc Plane TC Rate-Scheduler MMW */ +#define E1000_RTTPTCRS(_n) (0x34A0 + ((_n) * 4)) /* Tx Packet plane TC Rate-Scheduler Status */ +#define E1000_RTTPTCRM(_n) (0x34C0 + ((_n) * 4)) /* Tx Packet plane TC Rate-scheduler MMW */ +#define E1000_RTRPTCRS(_n) (0x24A0 + ((_n) * 4)) /* Rx Packet plane TC Rate-Scheduler Status */ +#define E1000_RTRPTCRM(_n) (0x24C0 + ((_n) * 4)) /* Rx Packet plane TC Rate-Scheduler MMW */ +#define E1000_RTTDVMRM(_n) (0x3670 + ((_n) * 4)) /* Tx Desc plane VM Rate-Scheduler MMW*/ +#define E1000_RTTBCNRM(_n) (0x3690 + ((_n) * 4)) /* Tx BCN Rate-Scheduler MMW */ +#define E1000_RTTDQSEL 0x3604 /* Tx Desc Plane Queue Select */ +#define E1000_RTTDVMRC 0x3608 /* Tx Desc Plane VM Rate-Scheduler Config */ +#define E1000_RTTDVMRS 0x360C /* Tx Desc Plane VM Rate-Scheduler Status */ +#define E1000_RTTBCNRC 0x36B0 /* Tx BCN Rate-Scheduler Config */ +#define E1000_RTTBCNRS 0x36B4 /* Tx BCN Rate-Scheduler Status */ +#define E1000_RTTBCNCR 0xB200 /* Tx BCN Control Register */ +#define E1000_RTTBCNTG 0x35A4 /* Tx BCN Tagging */ +#define E1000_RTTBCNCP 0xB208 /* Tx BCN Congestion point */ +#define E1000_RTRBCNCR 0xB20C /* Rx BCN Control Register */ +#define E1000_RTTBCNRD 0x36B8 /* Tx BCN Rate Drift */ +#define E1000_PFCTOP 0x1080 /* Priority Flow Control Type and Opcode */ +#define E1000_RTTBCNIDX 0xB204 /* Tx BCN Congestion Point */ +#define E1000_RTTBCNACH 0x0B214 /* Tx BCN Control High */ +#define E1000_RTTBCNACL 0x0B210 /* Tx BCN Control Low */ + +#endif