Florian Fainelli [Fri, 10 Jun 2016 01:23:53 +0000 (18:23 -0700)]
net: dsa: b53: Add support for Broadcom RoboSwitch
This patch adds support for Broadcom's BCM53xx switch family, also known
as RoboSwitch. Some of these switches are ubiquituous, found in home
routers, Wi-Fi routers, DSL and cable modem gateways and other
networking related products.
This drivers adds the library driver (b53_common.c) as well as a few bus
glue drivers for MDIO, SPI, Switch Register Access Block (SRAB) and
memory-mapped I/O into a SoC's address space (Broadcom BCM63xx/33xx).
Basic operations are supported to bring the Layer 1/2 up and running,
but not much more at this point, subsequent patches add the remaining
features.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 10 Jun 2016 05:12:49 +0000 (22:12 -0700)]
Merge branch 'bcm_sf2-vlan'
Florian Fainelli says:
====================
net: dsa: bcm_sf2: add VLAN support
This is long overdue, finally add support for VLANs in the Broadcom Starfigther
2 switch driver.
There are a few things that make us differ from e.g; mv88e6xxx.c:
- we keep a software cache of which VLANs are enabled and which are not to
dramatically speed up the VLAN dump operation, we do not have any HW operation
which would only return the list of valid VLAN entries, they would have to be
all queried one by one, with 4K vlans, this takes a while
- the default behavior is equivalent to setting VLAN filtering to 1, still working
on implementing a proper port_vlan_filtering callback, but I figured the most
conservative behavior is probably okay anyway
- without enabling VLANs, the default behavior is to receive any 802.1q frames
(per the DSA documentation), however, once we start enabling VLAN support, if
an interface leaves the bridge, we still want it to receive all 802.1q frames
so we utiliez the "Join all VLAN" feature of the switch to perform that
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Fri, 10 Jun 2016 00:42:08 +0000 (17:42 -0700)]
net: dsa: bcm_sf2: Add VLAN support
Add support for configuring VLANs on the Broadcom Starfigther2 switch.
This is all done through the bridge vlan facility just like other DSA
drivers.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Fri, 10 Jun 2016 00:42:07 +0000 (17:42 -0700)]
net: dsa: bcm_sf2: Add VLAN registers definitions
Add the definitions for the VLAN registers that we are going to
manipulate in subsequent patches.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Fri, 10 Jun 2016 00:42:06 +0000 (17:42 -0700)]
net: dsa: bcm_sf2: Move setup function at the far end
Re-order the bcm_sf2_sw_setup() function so that it is at the far end of
the driver to avoid any kind of forward declarations.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Fri, 10 Jun 2016 00:42:05 +0000 (17:42 -0700)]
net: dsa: bcm_sf2: Split fast age into a helper function
Add a helper function to fast age something that is controlled by the
caller: port, VLAN. We will use this to implement a VLAN fast age
operation.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 9 Jun 2016 20:28:38 +0000 (13:28 -0700)]
Merge branch 'netdev_lockdep_set_classes'
Eric Dumazet says:
====================
net: better lockdep annotations
Introduction of qdisc->running seqcount added lockdep false positives.
While chasing the bug, it came to me that we had a lot of copies of the
same stuff in virtual drivers.
This patch series has the qdisc->running fix (considers that a trylock
is attempted in lockdep terminology), and adds a generic helper so
that we no longer have to patch many virtual drivers when a new per-device
or per-qdisc lock is added.
Thanks to David Ahern for reporting the issue and testing my patches :)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 9 Jun 2016 14:45:15 +0000 (07:45 -0700)]
net: ipvlan: call netdev_lockdep_set_classes()
In case a qdisc is used on a ipvlan device, we need to use different
lockdep classes to avoid false positives.
Use the new netdev_lockdep_set_classes() generic helper.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 9 Jun 2016 14:45:14 +0000 (07:45 -0700)]
net: macvlan: call netdev_lockdep_set_classes()
In case a qdisc is used on a macvlan device, we need to use different
lockdep classes to avoid false positives.
Use the new netdev_lockdep_set_classes() generic helper.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 9 Jun 2016 14:45:13 +0000 (07:45 -0700)]
net: vrf: call netdev_lockdep_set_classes()
In case a qdisc is used on a vrf device, we need to use different
lockdep classes to avoid false positives.
Use the new netdev_lockdep_set_classes() generic helper.
Reported-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 9 Jun 2016 14:45:12 +0000 (07:45 -0700)]
net: add netdev_lockdep_set_classes() helper
It is time to add netdev_lockdep_set_classes() helper
so that lockdep annotations per device type are easier to manage.
This removes a lot of copies and missing annotations.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 9 Jun 2016 14:45:11 +0000 (07:45 -0700)]
net: sched: fix qdisc->running lockdep annotations
1) qdisc_run_begin() is really using the equivalent of a trylock.
Instead of using write_seqcount_begin(), use a combination of
raw_write_seqcount_begin() and correct lockdep annotation.
2) sch_direct_xmit() should use regular spin_lock(root_lock)
Fixes:
f9eb8aea2a1e ("net_sched: transform qdisc running bit into a seqcount")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vitaly Kuznetsov [Thu, 9 Jun 2016 10:44:03 +0000 (12:44 +0200)]
netvsc: get rid of completion timeouts
I'm hitting 5 second timeout in rndis_filter_set_rss_param() while setting
RSS parameters for the device. When this happens we end up returning
-ETIMEDOUT from the function and rndis_filter_device_add() falls back to
setting
net_device->max_chn = 1;
net_device->num_chn = 1;
net_device->num_sc_offered = 0;
but after a moment the rndis request succeeds and subchannels start to
appear. netvsc_sc_open() does unconditional nvscdev->num_sc_offered-- and
it becomes U32_MAX-1. Consequent rndis_filter_device_remove() will hang
while waiting for all U32_MAX-1 subchannels to appear and this is not
going to happen.
The immediate issue could be solved by adding num_sc_offered > 0 check to
netvsc_sc_open() but we're getting out of sync with the host and it's not
easy to adjust things later, e.g. in this particular case we'll be creating
queues without a user request for it and races are expected. Same applies
to other parts of the driver which have the same completion timeout.
Following the trend in drivers/hv/* code I suggest we remove all these
timeouts completely. As a guest we can always trust the host we're running
on and if the host screws things up there is no easy way to recover anyway.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Acked-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simon Horman [Thu, 9 Jun 2016 09:03:34 +0000 (18:03 +0900)]
sit: remove unnecessary protocol check in ipip6_tunnel_xmit()
ipip6_tunnel_xmit() is called immediately after checking that
skb->protocol is htons(ETH_P_IPV6) so there is no need
to check it a second time.
Found by inspection.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Dinan Gunawardena <dinan.gunawardena@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 9 Jun 2016 06:58:52 +0000 (23:58 -0700)]
Merge branch 'cbq-kill-drop'
Florian Westphal says:
====================
sched, cbq: remove OVL_STRATEGY/POLICE support
iproute2 does not implement any options that result in the
TCA_CBQ_OVL_STRATEGY/TCA_CBQ_POLICE attributes being set/used.
This series removes these two attributes from cbq and makes kernel reject
them via EOPNOTSUPP in case they are present.
The two followup changes then remove several features from qdisc
infrastructure that are then no longer used/needed. These are:
- The 'drop' method provided by most qdiscs
- the 'reshape_fail' function used by some qdiscs
- the __parent member in struct Qdisc
I tested this with allmod and allyesconfig builds and also with
a brief cbq script:
tc qdisc add dev eth0 root handle 1:0 cbq bandwidth 10Mbit avpkt 1000 cell 8
tc class add dev eth0 parent 1:0 classid 1:1 est 1sec 8sec cbq bandwidth 10Mbit rate 5Mbit prio 1 allot 1514 maxburst 20 cell 8 avpkt 1000 bounded split 1:0 defmap 3f
tc class add dev eth0 parent 1:0 classid 1:2 est 1sec 8sec cbq bandwidth 10Mbit rate 5Mbit prio 1 allot 1514 maxburst 20 cell 8 avpkt 1000 bounded split 1:0 defmap 3f
tc filter add dev eth0 parent 1:0 protocol ip prio 1 u32 match ip tos 0x10 0xff classid 1:1 police rate 2Mbit burst 10K reclassify
tc filter add dev eth0 parent 1:0 protocol ip prio 1 u32 match ip tos 0x0c 0xff classid 1:2
tc filter add dev eth0 parent 1:0 protocol ip prio 2 u32 match ip tos 0x10 0xff classid 1:2
tc filter add dev eth0 parent 1:0 protocol ip prio 3 u32 match ip tos 0x0 0x0 classid 1:2
No changes since v1 except patch #5 to fix up struct Qdisc layout.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Westphal [Wed, 8 Jun 2016 22:27:43 +0000 (00:27 +0200)]
sched: place state, next_sched and gso_skb in same cacheline again
Earlier commits removed two members from struct Qdisc which places
next_sched/gso_skb into a different cacheline than ->state.
This restores the struct layout to what it was before the removal.
Move the two members, then add an annotation so they all reside in the
same cacheline.
This adds a 16 byte hole after cpu_qstats.
The hole could be closed but as it doesn't decrease total struct size just
do it this way.
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Westphal [Wed, 8 Jun 2016 22:27:42 +0000 (00:27 +0200)]
sched: remove qdisc->drop
after removal of TCA_CBQ_OVL_STRATEGY from cbq scheduler, there are no
more callers of ->drop() outside of other ->drop functions, i.e.
nothing calls them.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Westphal [Wed, 8 Jun 2016 22:27:41 +0000 (00:27 +0200)]
sched: remove qdisc_rehape_fail
After the removal of TCA_CBQ_POLICE in cbq scheduler qdisc->reshape_fail
is always NULL, i.e. qdisc_rehape_fail is now the same as qdisc_drop.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Westphal [Wed, 8 Jun 2016 22:27:40 +0000 (00:27 +0200)]
cbq: remove TCA_CBQ_POLICE support
iproute2 doesn't implement any cbq option that results in this attribute
being sent to kernel.
To make use of it, user would have to
- patch iproute2
- add a class
- attach a qdisc to the class (default pfifo doesn't work as
q->handle is 0 and cbq_set_police() is a no-op in this case)
- re-'add' the same class (tc class change ...) again
- user must also specifiy a defmap (e.g. 'split 1:0 defmap 3f'), since
this 'police' feature relies on its presence
- the added qdisc must be one of bfifo, pfifo or netem
If all of these conditions are met and _some_ leaf qdiscs, namely
p/bfifo, netem, plug or tbf would drop a packet, kernel calls back into
cbq, which will attempt to re-queue the skb into a different class
as indicated by the parents' defmap entry for TC_PRIO_BESTEFFORT.
[ i.e. we behave as if tc_classify returned TC_ACT_RECLASSIFY ].
This feature, which isn't documented or implemented in iproute2,
and isn't implemented consistently (most qdiscs like sfq, codel, etc
drop right away instead of attempting this reclassification) is the
sole reason for the reshape_fail and __parent member in Qdisc struct.
So remove TCA_CBQ_POLICE support from the kernel, reject it via EOPNOTSUPP
so userspace knows we don't support it, and then remove no-longer needed
infrastructure in followup commit.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Westphal [Wed, 8 Jun 2016 22:27:39 +0000 (00:27 +0200)]
cbq: remove TCA_CBQ_OVL_STRATEGY support
since initial revision of cbq in 2004 iproute 2 has never implemented
support for TCA_CBQ_OVL_STRATEGY, which is what needs to be set to
activate the class->drop() call (TC_CBQ_OVL_DROP strategy must be
set by userspace value must be set by userspace).
David Miller says:
It seems really safe to kill this thing off, flag an error if someone
tries to set the attribute, and therefore kill off all of the
non-default cbq_ovl_*() functions.
A followup commit can then remove all .drop qdisc methods since this
removed the only caller.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shweta Choudaha [Wed, 8 Jun 2016 19:15:43 +0000 (20:15 +0100)]
ip6gre: Allow live link address change
The ip6 GRE tap device should not be forced to down state to change
the mac address and should allow live address change for tap device
similar to ipv4 gre.
Signed-off-by: Shweta Choudaha <schoudah@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 8 Jun 2016 18:36:02 +0000 (11:36 -0700)]
Merge branch 'vrf-fib-rule-improve'
David Ahern says:
====================
net: vrf: Improve use of FIB rules
Currently, VRFs require 1 oif and 1 iif rule per address family per
VRF. As the number of VRF devices increases it brings scalability
issues with the increasing rule list. All of the VRF rules have the
same format with the exception of the specific table id to direct the
lookup. Since the table id is available from the oif or iif in the
loopup, the VRF rules can be consolidated to a single rule that pulls
the table from the VRF device.
This solution still allows a user to insert their own rules for VRFs,
including rules with additional attributes. Accordingly, it is backwards
compatible with existing setups and allows other policy routing as
desired.
Hopefully v5 is the charm; my e-waste can is getting full.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Wed, 8 Jun 2016 17:55:40 +0000 (10:55 -0700)]
net: vrf: Add l3mdev rules on first device create
Add l3mdev rule per address family when the first VRF device is
created. The rules are installed with a default preference of 1000.
Users can replace the default rule as desired.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Wed, 8 Jun 2016 17:55:39 +0000 (10:55 -0700)]
net: Add l3mdev rule
Currently, VRFs require 1 oif and 1 iif rule per address family per
VRF. As the number of VRF devices increases it brings scalability
issues with the increasing rule list. All of the VRF rules have the
same format with the exception of the specific table id to direct the
lookup. Since the table id is available from the oif or iif in the
loopup, the VRF rules can be consolidated to a single rule that pulls
the table from the VRF device.
This patch introduces a new rule attribute l3mdev. The l3mdev rule
means the table id used for the lookup is pulled from the L3 master
device (e.g., VRF) rather than being statically defined. With the
l3mdev rule all of the basic VRF FIB rules are reduced to 1 l3mdev
rule per address family (IPv4 and IPv6).
If an admin wishes to insert higher priority rules for specific VRFs
those rules will co-exist with the l3mdev rule. This capability means
current VRF scripts will co-exist with this new simpler implementation.
Currently, the rules list for both ipv4 and ipv6 look like this:
$ ip ru ls
1000: from all oif vrf1 lookup 1001
1000: from all iif vrf1 lookup 1001
1000: from all oif vrf2 lookup 1002
1000: from all iif vrf2 lookup 1002
1000: from all oif vrf3 lookup 1003
1000: from all iif vrf3 lookup 1003
1000: from all oif vrf4 lookup 1004
1000: from all iif vrf4 lookup 1004
1000: from all oif vrf5 lookup 1005
1000: from all iif vrf5 lookup 1005
1000: from all oif vrf6 lookup 1006
1000: from all iif vrf6 lookup 1006
1000: from all oif vrf7 lookup 1007
1000: from all iif vrf7 lookup 1007
1000: from all oif vrf8 lookup 1008
1000: from all iif vrf8 lookup 1008
...
32765: from all lookup local
32766: from all lookup main
32767: from all lookup default
With the l3mdev rule the list is just the following regardless of the
number of VRFs:
$ ip ru ls
1000: from all lookup [l3mdev table]
32765: from all lookup local
32766: from all lookup main
32767: from all lookup default
(Note: the above pretty print of the rule is based on an iproute2
prototype. Actual verbage may change)
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 8 Jun 2016 18:27:02 +0000 (11:27 -0700)]
Merge branch 'tipc-small-fixes'
Jon Maloy says:
====================
tipc: two small fixes
We fix a couple of rarely seen anomalies discovered during testing.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Paul Maloy [Wed, 8 Jun 2016 16:00:05 +0000 (12:00 -0400)]
tipc: change node timer unit from jiffies to ms
The node keepalive interval is recalculated at each timer expiration
to catch any changes in the link tolerance, and stored in a field in
struct tipc_node. We use jiffies as unit for the stored value.
This is suboptimal, because it makes the calculation unnecessary
complex, including two unit conversions. The conversions also lead to
a rounding error that causes the link "abort limit" to be 3 in the
normal case, instead of 4, as intended. This again leads to unnecessary
link resets when the network is pushed close to its limit, e.g., in an
environment with hundreds of nodes or namesapces.
In this commit, we do instead let the keepalive value be calculated and
stored in milliseconds, so that there is only one conversion and the
rounding error is eliminated.
We also remove a redundant "keepalive" field in struct tipc_link. This
is remnant from the previous implementation.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Paul Maloy [Wed, 8 Jun 2016 16:00:04 +0000 (12:00 -0400)]
tipc: correct error in node fsm
commit
88e8ac7000dc ("tipc: reduce transmission rate of reset messages
when link is down") revealed a flaw in the node FSM, as defined in
the log of commit
66996b6c47ed ("tipc: extend node FSM").
We see the following scenario:
1: Node B receives a RESET message from node A before its link endpoint
is fully up, i.e., the node FSM is in state SELF_UP_PEER_COMING. This
event will not change the node FSM state, but the (distinct) link FSM
will move to state RESETTING.
2: As an effect of the previous event, the local endpoint on B will
declare node A lost, and post the event SELF_DOWN to the its node
FSM. This moves the FSM state to SELF_DOWN_PEER_LEAVING, meaning
that no messages will be accepted from A until it receives another
RESET message that confirms that A's endpoint has been reset. This
is wasteful, since we know this as a fact already from the first
received RESET, but worse is that the link instance's FSM has not
wasted this information, but instead moved on to state ESTABLISHING,
meaning that it repeatedly sends out ACTIVATE messages to the reset
peer A.
3: Node A will receive one of the ACTIVATE messages, move its link FSM
to state ESTABLISHED, and start repeatedly sending out STATE messages
to node B.
4: Node B will consistently drop these messages, since it can only accept
accept a RESET according to its node FSM.
5: After four lost STATE messages node A will reset its link and start
repeatedly sending out RESET messages to B.
6: Because of the reduced send rate for RESET messages, it is very
likely that A will receive an ACTIVATE (which is sent out at a much
higher frequency) before it gets the chance to send a RESET, and A
may hence quickly move back to state ESTABLISHED and continue sending
out STATE messages, which will again be dropped by B.
7: GOTO 5.
8: After having repeated the cycle 5-7 a number of times, node A will
by chance get in between with sending a RESET, and the situation is
resolved.
Unfortunately, we have seen that it may take a substantial amount of
time before this vicious loop is broken, sometimes in the order of
minutes.
We correct this by making a small correction to the node FSM: When a
node in state SELF_UP_PEER_COMING receives a SELF_DOWN event, it now
moves directly back to state SELF_DOWN_PEER_DOWN, instead of as now
SELF_DOWN_PEER_LEAVING. This is logically consistent, since we don't
need to wait for RESET confirmation from of an endpoint that we alread
know has been reset. It also means that node B in the scenario above
will not be dropping incoming STATE messages, and the link can come up
immediately.
Finally, a symmetry comparison reveals that the FSM has a similar
error when receiving the event PEER_DOWN in state PEER_UP_SELF_COMING.
Instead of moving to PERR_DOWN_SELF_LEAVING, it should move directly
to SELF_DOWN_PEER_DOWN. Although we have never seen any negative effect
of this logical error, we choose fix this one, too.
The node FSM looks as follows after those changes:
+----------------------------------------+
| PEER_DOWN_EVT|
| |
+------------------------+----------------+ |
|SELF_DOWN_EVT | | |
| | | |
| +-----------+ +-----------+ |
| |NODE_ | |NODE_ | |
| +----------|FAILINGOVER|<---------|SYNCHING |-----------+ |
| |SELF_ +-----------+ FAILOVER_+-----------+ PEER_ | |
| |DOWN_EVT | A BEGIN_EVT A | DOWN_EVT| |
| | | | | | | |
| | | | | | | |
| | |FAILOVER_ |FAILOVER_ |SYNCH_ |SYNCH_ | |
| | |END_EVT |BEGIN_EVT |BEGIN_EVT|END_EVT | |
| | | | | | | |
| | | | | | | |
| | | +--------------+ | | |
| | +-------->| SELF_UP_ |<-------+ | |
| | +-----------------| PEER_UP |----------------+ | |
| | |SELF_DOWN_EVT +--------------+ PEER_DOWN_EVT| | |
| | | A A | | |
| | | | | | | |
| | | PEER_UP_EVT| |SELF_UP_EVT | | |
| | | | | | | |
V V V | | V V V
+------------+ +-----------+ +-----------+ +------------+
|SELF_DOWN_ | |SELF_UP_ | |PEER_UP_ | |PEER_DOWN |
|PEER_LEAVING| |PEER_COMING| |SELF_COMING| |SELF_LEAVING|
+------------+ +-----------+ +-----------+ +------------+
| | A A | |
| | | | | |
| SELF_ | |SELF_ |PEER_ |PEER_ |
| DOWN_EVT| |UP_EVT |UP_EVT |DOWN_EVT |
| | | | | |
| | | | | |
| | +--------------+ | |
|PEER_DOWN_EVT +--->| SELF_DOWN_ |<---+ SELF_DOWN_EVT|
+------------------->| PEER_DOWN |<--------------------+
+--------------+
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 8 Jun 2016 18:23:42 +0000 (11:23 -0700)]
Merge branch 'dsa-misc-improvements'
Florian Fainelli says:
====================
net: dsa: misc improvements
This patch series builds on top of Andrew's "New DSA bind, switches as devices"
patch set and does the following:
- add a few helper functions/goodies for net/dsa/dsa2.c to be as close as possible
from net/dsa/dsa.c in terms of what drivers can expect, in particular the slave
MDIO bus and the enabled_port_mask and phy_mii_mask
- fix the CPU port ethtools ops to work in a multiple tree setup since we can
no longer assume a single tree is supported
- make the bcm_sf2 driver register its own MDIO bus, yet assign it to
ds->slave_mii_bus for everything to work in net/dsa/slave.c wrt. PHY probing,
this is a tad cleaner than what we have now
Changes in v2:
Most of the previous patches have been dropped to just keep the relevant ones
now.
Changes in v3:
- split the addition of the slave MII bus as a separate patch
- properly unwind all operations at the right place and right time (ethtool ops,
slave MDIO bus
- fixed a few typos here and there
Changes in v4:
- removed superfluous dst agrument to dsa_cpu_port_ethtool_{setup,restore}
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Tue, 7 Jun 2016 23:32:43 +0000 (16:32 -0700)]
net: dsa: bcm_sf2: Register our slave MDIO bus
Register a slave MDIO bus which allows us to divert problematic
read/writes towards conflicting pseudo-PHY address (30). Do no longer
rely on DSA's slave_mii_bus, but instead provide our own implementation
which offers more flexibility as to what to do, and when to register it.
We need to register it by the time we are able to get access to our
memory mapped registers, which is not until drv->setup() time. In order
to avoid forward declarations, we need to re-order the function bodies a
bit.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Tue, 7 Jun 2016 23:32:42 +0000 (16:32 -0700)]
net: dsa: Initialize CPU port ethtool ops per tree
Now that we can properly support multiple distinct trees in the system,
using a global variable: dsa_cpu_port_ethtool_ops is getting clobbered
as soon as the second switch tree gets probed, and we don't want that.
We need to move this to be dynamically allocated, and since we can't
really be comparing addresses anymore to determine first time
initialization versus any other times, just move this to dsa.c and
dsa2.c where the remainder of the dst/ds initialization happens.
The operations teardown restores the master netdev's ethtool_ops to its
original ethtool_ops pointer (typically within the Ethernet driver)
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Tue, 7 Jun 2016 23:32:41 +0000 (16:32 -0700)]
net: dsa: Add initialization helper for CPU port ethtool_ops
Add a helper function: dsa_cpu_port_ethtool_init() which initializes a
custom ethtool_ops structure with custom DSA ethtool operations for CPU
ports. This is a preliminary change to move the initialization outside
of net/dsa/slave.c.
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Tue, 7 Jun 2016 23:32:40 +0000 (16:32 -0700)]
net: dsa: Provide a slave MII bus if needed
Mimic what net/dsa/dsa.c does and provide a slave MII bus by default
which will be created if the driver implements a phy_read method.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Tue, 7 Jun 2016 23:32:39 +0000 (16:32 -0700)]
net: dsa: Initialize ds->enabled_port_mask and ds->phys_mii_mask
Some drivers rely on these two bitmasks to contain the correct values
for them to successfully probe and initialize at drv->setup() time,
calculate correct values to put in both masks as early as possible in
dsa_get_ports_dn().
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Tue, 7 Jun 2016 23:32:38 +0000 (16:32 -0700)]
net: dsa: Provide unique DSA slave MII bus names
In case we have multiples trees and switches with the same index, we
need to add another discriminating id: the switch tree.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 8 Jun 2016 14:22:49 +0000 (07:22 -0700)]
net: sched: fix missing doc annotations
"make htmldocs" complains otherwise:
.//net/core/gen_stats.c:168: warning: No description found for parameter 'running'
.//include/linux/netdevice.h:1867: warning: No description found for parameter 'qdisc_running_key'
Fixes:
f9eb8aea2a1e ("net_sched: transform qdisc running bit into a seqcount")
Fixes:
edb09eb17ed8 ("net: sched: do not acquire qdisc spinlock in qdisc/class stats dump")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hariprasad Shenai [Wed, 8 Jun 2016 12:39:08 +0000 (18:09 +0530)]
net: Reduce queue allocation to one in kdump kernel
When in kdump kernel, reduce memory usage by only using a single Queue
Set for multiqueue devices. So make netif_get_num_default_rss_queues()
return one, when in kdump kernel.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 8 Jun 2016 18:11:00 +0000 (11:11 -0700)]
Merge branch 'qed-dcbnl'
Sudarsana Reddy Kalluru says:
====================
qed/qede support for dcbnl.
This series adds the dcbnl functionality to the driver. Patch (1) adds
the qed infrastucture for querying/configuring the dcbx parameters.
Patch (2) adds the qed infrastructure for dcbnl APIs. And patch (3)
adds the qede support for dcbnl.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Sudarsana Reddy Kalluru [Wed, 8 Jun 2016 10:22:12 +0000 (06:22 -0400)]
qede: Add dcbnl support.
This patch adds the interfaces for ieee/cee dcbnl callbacks and registers
them with the kernel.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sudarsana Reddy Kalluru [Wed, 8 Jun 2016 10:22:11 +0000 (06:22 -0400)]
qed: Add dcbnl support.
This patch adds the implementation for both cee/ieee dcbnl callbacks by
using the qed query/config APIs.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sudarsana Reddy Kalluru [Wed, 8 Jun 2016 10:22:10 +0000 (06:22 -0400)]
qed: Add support for query/config dcbx.
Query API reads the dcbx data from the device shared memory and return it
to the caller. The config API configures the user provided dcbx values on
the device, and initiates the dcbx negotiation with the peer.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andreas Ziegler [Wed, 8 Jun 2016 09:36:56 +0000 (11:36 +0200)]
fsl/qe: Do not prefix header guard with CONFIG_
The CONFIG_ prefix should only be used for options which
can be configured through Kconfig and not for guarding headers.
Signed-off-by: Andreas Ziegler <andreas.ziegler@fau.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andreas Ziegler [Wed, 8 Jun 2016 09:40:28 +0000 (11:40 +0200)]
drivers/net/fsl_ucc: Do not prefix header guard with CONFIG_
The CONFIG_ prefix should only be used for options which
can be configured through Kconfig and not for guarding headers.
Signed-off-by: Andreas Ziegler <andreas.ziegler@fau.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Tue, 7 Jun 2016 23:09:44 +0000 (16:09 -0700)]
ila: Perform only one translation in forwarding path
When setting up ILA in a router we noticed that the the encapsulation
is invoked twice: once in the route input path and again upon route
output. To resolve this we add a flag set_csum_neutral for the
ila_update_ipv6_locator. If this flag is set and the checksum
neutral bit is also set we assume that checksum-neutral translation
has already been performed and take no further action. The
flag is set only in ila_output path. The flag is not set for ila_input and
ila_xlat.
Tested:
Used 3 netns to set to emulate a router and two hosts. The router
translates SIR addresses between the two destinations in other two netns.
Verified ping and netperf are functional.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pau Espin Pedrol [Tue, 7 Jun 2016 14:30:34 +0000 (16:30 +0200)]
tcp: accept RST if SEQ matches right edge of right-most SACK block
RFC 5961 advises to only accept RST packets containing a seq number
matching the next expected seq number instead of the whole receive
window in order to avoid spoofing attacks.
However, this situation is not optimal in the case SACK is in use at the
time the RST is sent. I recently run into a scenario in which packet
losses were high while uploading data to a server, and userspace was
willing to frequently terminate connections by sending a RST. In
this case, the ACK sent on the receiver side (rcv_nxt) is frozen waiting
for a lost packet retransmission and SACK blocks are used to let the
client continue uploading data. At some point later on, the client sends
the RST (snd_nxt), which matches the next expected seq number of the
right-most SACK block on the receiver side which is going forward
receiving data.
In this scenario, as RFC 5961 defines, the RST SEQ doesn't match the
frozen main ACK at receiver side and thus gets dropped and a challenge
ACK is sent, which gets usually lost due to network conditions. The main
consequence is that the connection stays alive for a while even if it
made sense to accept the RST. This can get really bad if lots of
connections like this one are created in few seconds, allocating all the
resources of the server easily.
For security reasons, not all SACK blocks are checked (there could be a
big amount of SACK blocks => acceptable SEQ numbers). Furthermore, it
wouldn't make sense to check for RST in blocks other than the right-most
received one because the sender is not expected to be sending new data
after the RST. For simplicity, only up to the 4 most recently updated
SACK blocks (selective_acks[4] field) are compared to find the
right-most block, as usually those are the ones with bigger probability
to contain it.
This patch was tested in a 3.18 kernel and probed to improve the
situation in the scenario described above.
Signed-off-by: Pau Espin Pedrol <pau.espin@tessares.net>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Tested-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Tue, 7 Jun 2016 12:04:16 +0000 (15:04 +0300)]
qed: potential overflow in qed_cxt_src_t2_alloc()
In the current code "ent_per_page" could be more than "conn_num" making
"conn_num" negative after the subtraction. In the next iteration
through the loop then the negative is treated as a very high positive
meaning we don't put a limit on "ent_num". It could lead to memory
corruption.
Fixes:
dbb799c39717 ('qed: Initialize hardware for new protocols')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 8 Jun 2016 07:25:38 +0000 (00:25 -0700)]
Merge branch 'vrf-local'
David Ahern says:
====================
net: vrf: Add support for local traffic to local addresses
Add support for locally originated traffic to VRF-local addresses,
be it addresses on enslaved devices or addresses on the VRF device:
$ ip addr show dev red
33: red: <NOARP,MASTER,UP,LOWER_UP> mtu 65536 qdisc pfifo_fast state UP group default qlen 1000
link/ether be:00:53:b5:e4:25 brd ff:ff:ff:ff:ff:ff
inet 1.1.1.1/32 scope global red
valid_lft forever preferred_lft forever
inet6 1111:1::1/128 scope global
valid_lft forever preferred_lft forever
$ ip addr show dev eth1
3: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master red state UP group default qlen 1000
link/ether 02:e0:f9:79:34:bd brd ff:ff:ff:ff:ff:ff
inet 10.100.1.1/24 brd 10.100.1.255 scope global eth1
valid_lft forever preferred_lft forever
inet6 2100:1::1/120 scope global
valid_lft forever preferred_lft forever
inet6 fe80::e0:f9ff:fe79:34bd/64 scope link
valid_lft forever preferred_lft forever
$ ping -c1 -I red 10.100.1.1
ping: Warning: source address might be selected on device other than red.
PING 10.100.1.1 (10.100.1.1) from 10.100.1.1 red: 56(84) bytes of data.
64 bytes from 10.100.1.1: icmp_seq=1 ttl=64 time=0.057 ms
$ ping -c1 -I red 1.1.1.1
PING 1.1.1.1 (1.1.1.1) from 1.1.1.1 red: 56(84) bytes of data.
64 bytes from 1.1.1.1: icmp_seq=1 ttl=64 time=0.136 ms
--- 1.1.1.1 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.136/0.136/0.136/0.000 ms
$ ping6 -c1 -I red 2100:1::1
ping6: Warning: source address might be selected on device other than red.
PING 2100:1::1(2100:1::1) from 2100:1::1 red: 56 data bytes
64 bytes from 2100:1::1: icmp_seq=1 ttl=64 time=0.167 ms
--- 2100:1::1 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.167/0.167/0.167/0.000 ms
$ ping6 -c1 -I red 1111::1
PING 1111::1(1111::1) from 1111:1::1 red: 56 data bytes
64 bytes from 1111::1: icmp_seq=1 ttl=64 time=0.187 ms
--- 1111::1 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.187/0.187/0.187/0.000 ms
This change also enables use of loopback address on the VRF device:
$ ip addr add dev red 127.0.0.1/8
$ ping -c1 -I red 127.0.0.1
PING 127.0.0.1 (127.0.0.1) from 127.0.0.1 red: 56(84) bytes of data.
64 bytes from 127.0.0.1: icmp_seq=1 ttl=64 time=0.058 ms
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Tue, 7 Jun 2016 03:50:40 +0000 (20:50 -0700)]
net: vrf: ipv6 support for local traffic to local addresses
Add support for locally originated traffic to VRF-local IPv6 addresses.
Similar to IPv4 a local dst is set on the skb and the packet is
reinserted with a call to netif_rx. With this patch, ping, tcp and udp
packets to a local IPv6 address are successfully routed:
$ ip addr show dev eth1
4: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master red state UP group default qlen 1000
link/ether 02:e0:f9:1c:b9:74 brd ff:ff:ff:ff:ff:ff
inet 10.100.1.1/24 brd 10.100.1.255 scope global eth1
valid_lft forever preferred_lft forever
inet6 2100:1::1/120 scope global
valid_lft forever preferred_lft forever
inet6 fe80::e0:f9ff:fe1c:b974/64 scope link
valid_lft forever preferred_lft forever
$ ping6 -c1 -I red 2100:1::1
ping6: Warning: source address might be selected on device other than red.
PING 2100:1::1(2100:1::1) from 2100:1::1 red: 56 data bytes
64 bytes from 2100:1::1: icmp_seq=1 ttl=64 time=0.098 ms
ip6_input is exported so the VRF driver can use it for the dst input
function. The dst_alloc function for IPv4 defaults to setting the input and
output functions; IPv6's does not. VRF does not need to duplicate the Rx path
so just export the ipv6 input function.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Tue, 7 Jun 2016 03:50:39 +0000 (20:50 -0700)]
net: vrf: ipv4 support for local traffic to local addresses
Add support for locally originated traffic to VRF-local addresses. If
destination device for an skb is the loopback or VRF device then set
its dst to a local version of the VRF cached dst_entry and call netif_rx
to insert the packet onto the rx queue - similar to what is done for
loopback. This patch handles IPv4 support; follow on patch handles IPv6.
With this patch, ping, tcp and udp packets to a local IPv4 address are
successfully routed:
$ ip addr show dev eth1
4: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master red state UP group default qlen 1000
link/ether 02:e0:f9:1c:b9:74 brd ff:ff:ff:ff:ff:ff
inet 10.100.1.1/24 brd 10.100.1.255 scope global eth1
valid_lft forever preferred_lft forever
inet6 2100:1::1/120 scope global
valid_lft forever preferred_lft forever
inet6 fe80::e0:f9ff:fe1c:b974/64 scope link
valid_lft forever preferred_lft forever
$ ping -c1 -I red 10.100.1.1
ping: Warning: source address might be selected on device other than red.
PING 10.100.1.1 (10.100.1.1) from 10.100.1.1 red: 56(84) bytes of data.
64 bytes from 10.100.1.1: icmp_seq=1 ttl=64 time=0.057 ms
This patch also enables use of IPv4 loopback address on the VRF device:
$ ip addr add dev red 127.0.0.1/8
$ ping -c1 -I red 127.0.0.1
PING 127.0.0.1 (127.0.0.1) from 127.0.0.1 red: 56(84) bytes of data.
64 bytes from 127.0.0.1: icmp_seq=1 ttl=64 time=0.058 ms
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Tue, 7 Jun 2016 03:50:38 +0000 (20:50 -0700)]
net: vrf: Minor refactoring for local address patches
Move the stripping of the ethernet header from is_ip_tx_frame into the
ipv4 and ipv6 outbound functions and collapse vrf_send_v4_prep into
vrf_process_v4_outbound.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Mon, 6 Jun 2016 23:06:02 +0000 (16:06 -0700)]
gue: Implement direction IP encapsulation
This patch implements direct encapsulation of IPv4 and IPv6 packets
in UDP. This is done a version "1" of GUE and as explained in I-D
draft-ietf-nvo3-gue-03.
Changes here are only in the receive path, fou with IPxIPx already
supports the transmit side. Both the normal receive path and
GRO path are modified to check for GUE version and check for
IP version in the case that GUE version is "1".
Tested:
IPIP with direct GUE encap
1 TCP_STREAM
4530 Mbps
200 TCP_RR
1297625 tps
135/232/444 90/95/99% latencies
IP4IP6 with direct GUE encap
1 TCP_STREAM
4903 Mbps
200 TCP_RR
1184481 tps
149/253/473 90/95/99% latencies
IP6IP6 direct GUE encap
1 TCP_STREAM
5146 Mbps
200 TCP_RR
1202879 tps
146/251/472 90/95/99% latencies
SIT with direct GUE encap
1 TCP_STREAM
6111 Mbps
200 TCP_RR
1250337 tps
139/241/467 90/95/99% latencies
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 7 Jun 2016 23:37:14 +0000 (16:37 -0700)]
Merge branch 'net-sched-fast-stats'
Eric Dumazet says:
====================
net: sched: faster stats gathering
A while back, I sent one RFC patch using lockless stats gathering
on 64bit arches.
This patch series does it more cleanly, using a seqcount.
Since qdisc/class stats are written at dequeue() time,
we can ask the dequeue to change the seqcount, so that
stats readers can avoid taking the root qdisc lock,
and instead the typical read_seqcount_{begin|retry} guarded
loop.
This does not change fast path costs, as the seqcount
increments are not more expensive than the bit manipulation,
and allows readers to not freeze the fast path anymore.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 6 Jun 2016 16:37:16 +0000 (09:37 -0700)]
net: sched: do not acquire qdisc spinlock in qdisc/class stats dump
Large tc dumps (tc -s {qdisc|class} sh dev ethX) done by Google BwE host
agent [1] are problematic at scale :
For each qdisc/class found in the dump, we currently lock the root qdisc
spinlock in order to get stats. Sampling stats every 5 seconds from
thousands of HTB classes is a challenge when the root qdisc spinlock is
under high pressure. Not only the dumps take time, they also slow
down the fast path (queue/dequeue packets) by 10 % to 20 % in some cases.
An audit of existing qdiscs showed that sch_fq_codel is the only qdisc
that might need the qdisc lock in fq_codel_dump_stats() and
fq_codel_dump_class_stats()
In v2 of this patch, I now use the Qdisc running seqcount to provide
consistent reads of packets/bytes counters, regardless of 32/64 bit arches.
I also changed rate estimators to use the same infrastructure
so that they no longer need to lock root qdisc lock.
[1]
http://static.googleusercontent.com/media/research.google.com/en//pubs/archive/43838.pdf
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: Kevin Athey <kda@google.com>
Cc: Xiaotian Pei <xiaotian@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 6 Jun 2016 16:37:15 +0000 (09:37 -0700)]
net_sched: transform qdisc running bit into a seqcount
Instead of using a single bit (__QDISC___STATE_RUNNING)
in sch->__state, use a seqcount.
This adds lockdep support, but more importantly it will allow us
to sample qdisc/class statistics without having to grab qdisc root lock.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 7 Jun 2016 23:18:20 +0000 (16:18 -0700)]
Merge branch 'be2net-noncrit-fixes'
Sathya Perla says:
====================
be2net: patch set
Hi David, the following patch set contains three non-critical fixes that
can go into the net-next tree.
Patch 1 fixes the logic for provisioning queue pairs on VFs to take into
account the limit on number of TXQs too as in some profiles the number
of TXQs is less than that of RXQs.
Patch 2 enables WoL support from shutdown on Skyhawk.
Patch 3 enhances the logic for provisioning queue pairs on VFs on
SR-IOV over multi-partition configs. Each PF (partition) on a port has to
compute the number of RSS tables it's VFs can use.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Somnath Kotur [Mon, 6 Jun 2016 11:22:10 +0000 (07:22 -0400)]
be2net: Fix provisioning of RSS for VFs in multi-partition configurations
Currently, we do not distribute queue resources to enable RSS for VFs
in multi-channel/partition configurations.
Fix this by having each PF(SRIOV capable) calculate it's share of the
15 RSS Policy Tables available per port before provisioning resources for
all the VFs.
This proportional share calculation is done based on division of the
PF's MAX VFs with the Total MAX VFs on that port. It also needs to
learn about the no: of NIC PFs on the port and subtract that from
the 15 RSS Policy Tables on the port.
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sriharsha Basavapatna [Mon, 6 Jun 2016 11:22:09 +0000 (07:22 -0400)]
be2net: Enable Wake-On-LAN from shutdown for Skyhawk
Skyhawk does support wake-up from ACPI shutdown state - S5, provided the
platform supports it (like Auxiliary power source etc). The changes listed
below are done to fix this.
1) There's no need to defer the HW configuration of WOL to be_suspend().
Remove this in be_suspend() and move it to be_set_wol() ethtool function
so it is configured directly in the context of ethtool. This automatically
takes care of the shutdown case.
2) The driver incorrectly uses WOL_CAP field in the FW response to
get_acpi_wol_cap() command, to determine if WOL is enabled. Instead the
driver must rely on the macaddr field in the response to infer WOL state.
3) In be_get_config() during init, if we find that WOL is enabled in FW,
call pci_enable_wake() to enable pmcsr.pme_en bit. This is needed to
support persistent WOL configuration provided by the FW in some platforms.
4) Remove code in be_set_wol() that writes to PCICFG_PM_CONTROL_OFFSET
to set pme_en bit; pci_enable_wake() sets that.
Fixes:
028991e49 ("Enabling Wake-on-LAN is not supported in S5 state")
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Suresh Reddy [Mon, 6 Jun 2016 11:22:08 +0000 (07:22 -0400)]
be2net: use max-TXQs limit too while provisioning VF queue pairs
When the PF driver provisions resources for VFs, it currently only looks
at max RSS queues available to calculate the number of VF queue pairs.
This logic breaks when there are less number of TX-queues than RSS-queues.
This patch fixes this problem by using the max-TXQs available in the
PF-pool in the calculations. As a part of this change the
be_calculate_vf_qs() routine is renamed as be_calculate_vf_res() and the
code that calculates limits on other related resources is moved here to
contain all resource calculation code inside one routine.
Signed-off-by: Suresh Reddy <suresh.reddy@broadcom.com>
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Zhao Qiang [Mon, 6 Jun 2016 06:30:02 +0000 (14:30 +0800)]
drivers/net: support hdlc function for QE-UCC
The driver add hdlc support for Freescale QUICC Engine.
It support NMSI and TSA mode.
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Zhao Qiang [Mon, 6 Jun 2016 06:30:01 +0000 (14:30 +0800)]
fsl/qe: Add QE TDM lib
QE has module to support TDM, some other protocols
supported by QE are based on TDM.
add a qe-tdm lib, this lib provides functions to the protocols
using TDM to configurate QE-TDM.
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Zhao Qiang [Mon, 6 Jun 2016 06:30:00 +0000 (14:30 +0800)]
fsl/qe: Make regs resouce_size_t
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Zhao Qiang [Mon, 6 Jun 2016 06:29:59 +0000 (14:29 +0800)]
fsl/qe: setup clock source for TDM mode
Add tdm clock configuration in both qe clock system and ucc
fast controller.
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Zhao Qiang [Mon, 6 Jun 2016 06:29:58 +0000 (14:29 +0800)]
fsl/qe: add rx_sync and tx_sync for TDM mode
Rx_sync and tx_sync are used by QE-TDM mode,
add them to struct ucc_fast_info.
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jamal Hadi Salim [Sun, 5 Jun 2016 14:41:32 +0000 (10:41 -0400)]
net sched: indentation and other OCD stylistic fixes
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
David S. Miller [Tue, 7 Jun 2016 22:53:44 +0000 (15:53 -0700)]
Merge branch 'sch-action-tstamp'
Jamal Hadi Salim says:
====================
net sched action timestamp improvements
Various aggregations of duplicated code, fixes and introduction of firstused
timestamp
v2: add const for source time info per suggestion from Cong
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jamal Hadi Salim [Mon, 6 Jun 2016 10:32:55 +0000 (06:32 -0400)]
net sched actions: aggregate dumping of actions timeinfo
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jamal Hadi Salim [Mon, 6 Jun 2016 10:32:54 +0000 (06:32 -0400)]
net sched actions: introduce timestamp for firsttime use
Useful to know when the action was first used for accounting
(and debugging)
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jamal Hadi Salim [Mon, 6 Jun 2016 10:32:53 +0000 (06:32 -0400)]
net sched: actions use tcf_lastuse_update for consistency
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Amir Vadai [Sun, 5 Jun 2016 14:11:18 +0000 (17:11 +0300)]
net/sched: cls_flower: Introduce support in SKIP SW flag
In order to make a filter processed only by hardware, skip_sw flag
should be supplied. This is an addition to the already existing skip_hw
flag (filter will be processed by software only). If no flag is
specified, filter will be processed by both software and hardware.
If only hardware offloaded filters exist, fl_classify() will return
without doing anything.
A following userspace patch will be sent once kernel patch is accepted.
Example:
tc filter add dev enp0s9 protocol ip prio 20 parent ffff: \
flower \
ip_proto 6 \
indev enp0s9 \
skip_sw \
action skbedit mark 0x1234
Signed-off-by: Amir Vadai <amirva@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 7 Jun 2016 22:40:12 +0000 (15:40 -0700)]
Merge branch 'qed-iov-fw-reqs'
Yuval Mintz says:
====================
qed: IOV series - relax firmware requirements
In order for VFs to work, current implementation demands that the VF's
requried storm firmware would be exactly the version that was loaded by
the PF, which is a very harsh requirement.
This patch series is intended to relax this -
the recently submitted firmware is intended to be forward/backward
compatible in its fastpath [slowpath is configured by PF on behalf of VF],
and so VFs would only be required of having the same major faspath HSI in
order to work.
Most of the other patches in this series extend current forward
compatibilty of driver to reduce chance of breaking PF/VF compatibility
in the future. A few are unrelated IOV changes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz [Sun, 5 Jun 2016 10:11:16 +0000 (13:11 +0300)]
qed: PF to reply to unknown messages
If a future VF would send the PF an unknown message, the PF today would
not send a reply. This would have 2 bad effects:
a. VF would have to timeout on the request.
b. If VF were to send an additional message to PF, firmware would mark
it as malicious.
Instead, if there's some valid reply-address on the message - let the PF
answer and tell the VF it doesn't know the message.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz [Sun, 5 Jun 2016 10:11:15 +0000 (13:11 +0300)]
qed: PF enforce MAC limitation of VFs
The only limitation relating to MACs the PF enforce today on its VFs
is in case it has a forced-unicast MAC address for them, in which case
they can't configure other unicast addresses.
Specifically, the PF isn't enforcing the number of MAC addresse a VF can
configure regardless of the nubmer of such filters agreed upon by PF and
VF during the acquisition process.
PF's shadow-config is now extended to also contain information about its
VFs' unicast addresses configuration, allowing such enforcement.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz [Sun, 5 Jun 2016 10:11:14 +0000 (13:11 +0300)]
qed: Move doorbell calculation from VF to PF
Today, the VF is aware of its queues context-ids, and calculates the
doorbell address when opening its queues on its own.
The configuration of doorbells in HW can sometime in the future be changed
by the PF [hw has several configurable features that might affect doorbell
addresses, e.g., dpm support], this would break compatibility with older
VFs as their calculated doorbell addresses would be incorrect for such a
configuration.
In order to avoid such a backward compatibility failure, let the PF make
the calculation of the doorbell offset based on the context-id, and pass
that to the VF.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz [Sun, 5 Jun 2016 10:11:13 +0000 (13:11 +0300)]
qed: Make PF more robust against malicious VF
There are several requests the VF can make toward the PF which the driver
would pass to firmware without checking the validity first - specifically,
opening queues and updating vports. Such configurations might cause the
firmware to assert.
This adds validation of the legality of said configurations on the PF side
before passing it onward via ramrod to firmware.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz [Sun, 5 Jun 2016 10:11:12 +0000 (13:11 +0300)]
qed: PF-VF resource negotiation
One of the goals of the vf's first message to the PF [acquire]
is to learn about the number of resources available to it [macs, vlans,
etc.]. This is done via negotiation - the VF requires a set of resources,
which the PF either approves or disaproves and sends a smaller set of
resources as alternative. In this later case, the VF is then expected to
either abort the probe or re-send the acquire message with less
required resources.
While this infrastructure exists since the initial submision of qed
SRIOV support, it's in fact completely inoperational - PF isn't really
looking into the resources the VF has asked for and is never going to
reply to the VF that it lacks resources.
This patch addresses this flow, fixing it and allowing the PF and VF
to actually agree on a set of resources.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz [Sun, 5 Jun 2016 10:11:11 +0000 (13:11 +0300)]
qed: Relax VF firmware requirements
Current driver require an exact match between VF and PF storm firmware;
Any difference would fail the VF acquire message, causing the VF probe
to be aborted.
While there's still dependencies between the two, the recent FW submission
has relaxed the match requirement - instead of an exact match, there's now
a 'fastpath' HSI major/minor scheme, where VFs and PFs that match in their
major number can co-exist even if their minor is different.
In order to accomadate this change some changes in the vf-start init flow
had to be made, as the VF start ramrod now has to be sent only after PF
learns which fastpath HSI its VF is requiring.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sun, 5 Jun 2016 03:02:28 +0000 (20:02 -0700)]
net: get rid of spin_trylock() in net_tx_action()
Note: Tom Herbert posted almost same patch 3 months back, but for
different reasons.
The reasons we want to get rid of this spin_trylock() are :
1) Under high qdisc pressure, the spin_trylock() has almost no
chance to succeed.
2) We loop multiple times in softirq handler, eventually reaching
the max retry count (10), and we schedule ksoftirqd.
Since we want to adhere more strictly to ksoftirqd being waked up in
the future (https://lwn.net/Articles/687617/), better avoid spurious
wakeups.
3) calls to __netif_reschedule() dirty the cache line containing
q->next_sched, slowing down the owner of qdisc.
4) RT kernels can not use the spin_trylock() here.
With help of busylock, we get the qdisc spinlock fast enough, and
the trylock trick brings only performance penalty.
Depending on qdisc setup, I observed a gain of up to 19 % in qdisc
performance (1016600 pps instead of 853400 pps, using prio+tbf+fq_codel)
("mpstat -I SCPU 1" is much happier now)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tom Herbert <tom@herbertland.com>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Wang [Wed, 1 Jun 2016 05:56:33 +0000 (01:56 -0400)]
vhost_net: stop polling socket during rx processing
We don't stop rx polling socket during rx processing, this will lead
unnecessary wakeups from under layer net devices (E.g
sock_def_readable() form tun). Rx will be slowed down in this
way. This patch avoids this by stop polling socket during rx
processing. A small drawback is that this introduces some overheads in
light load case because of the extra start/stop polling, but single
netperf TCP_RR does not notice any change. In a super heavy load case,
e.g using pktgen to inject packet to guest, we get about ~8.8%
improvement on pps:
before: ~1240000 pkt/s
after: ~1350000 pkt/s
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bhaktipriya Shridhar [Sat, 4 Jun 2016 15:24:00 +0000 (20:54 +0530)]
net: ethernet: cavium: liquidio: request_manager: Remove create_workqueue
alloc_workqueue replaces deprecated create_workqueue().
A dedicated workqueue has been used since the workitem viz
(&db_wq->wk.work which maps to check_db_timeout) is involved
in normal device operation. WQ_MEM_RECLAIM has been set to guarantee
forward progress under memory pressure, which is a requirement here.
Since there are only a fixed number of work items, explicit concurrency
limit is unnecessary.
flush_workqueue is unnecessary since destroy_workqueue() itself calls
drain_workqueue() which flushes repeatedly till the workqueue
becomes empty.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bhaktipriya Shridhar [Sat, 4 Jun 2016 14:51:40 +0000 (20:21 +0530)]
net: ethernet: cavium: liquidio: response_manager: Remove create_workqueue
alloc_workqueue replaces deprecated create_workqueue().
A dedicated workqueue has been used since the workitem viz
(&cwq->wk.work which maps to oct_poll_req_completion) is involved
in normal device operation. WQ_MEM_RECLAIM has been set to guarantee
forward progress under memory pressure, which is a requirement here.
Since there are only a fixed number of work items, explicit concurrency
limit is unnecessary.
flush_workqueue is unnecessary since destroy_workqueue() itself calls
drain_workqueue() which flushes repeatedly till the workqueue
becomes empty. Hence the call to flush_workqueue() has been dropped.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aaron Conole [Fri, 3 Jun 2016 20:57:12 +0000 (16:57 -0400)]
virtio-net: Add initial MTU advice feature
This commit adds the feature bit and associated mtu device entry for the
virtio network device. When a virtio device comes up, it checks the
feature bit for the VIRTIO_NET_F_MTU feature. If such feature bit is
enabled, the driver will read the advised MTU and use it as the initial
value.
Signed-off-by: Aaron Conole <aconole@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 6 Jun 2016 22:58:34 +0000 (15:58 -0700)]
net: Revert vrf-local changes.
This reverts commit
2fb7ea455d57e22110c54fc2de0656b6f744263c.
It results in build errors because ip6_input is not a
symbol exported to modules.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 6 Jun 2016 22:19:07 +0000 (15:19 -0700)]
Merge branch 'vrf-local'
David Ahern says:
====================
net: vrf: Add support for local traffic to local addresses
Add support for locally originated traffic to VRF-local addresses,
be it addresses on enslaved devices or addresses on the VRF device:
$ ip addr show dev red
33: red: <NOARP,MASTER,UP,LOWER_UP> mtu 65536 qdisc pfifo_fast state UP group default qlen 1000
link/ether be:00:53:b5:e4:25 brd ff:ff:ff:ff:ff:ff
inet 1.1.1.1/32 scope global red
valid_lft forever preferred_lft forever
inet6 1111:1::1/128 scope global
valid_lft forever preferred_lft forever
$ ip addr show dev eth1
3: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master red state UP group default qlen 1000
link/ether 02:e0:f9:79:34:bd brd ff:ff:ff:ff:ff:ff
inet 10.100.1.1/24 brd 10.100.1.255 scope global eth1
valid_lft forever preferred_lft forever
inet6 2100:1::1/120 scope global
valid_lft forever preferred_lft forever
inet6 fe80::e0:f9ff:fe79:34bd/64 scope link
valid_lft forever preferred_lft forever
$ ping -c1 -I red 10.100.1.1
ping: Warning: source address might be selected on device other than red.
PING 10.100.1.1 (10.100.1.1) from 10.100.1.1 red: 56(84) bytes of data.
64 bytes from 10.100.1.1: icmp_seq=1 ttl=64 time=0.057 ms
$ ping -c1 -I red 1.1.1.1
PING 1.1.1.1 (1.1.1.1) from 1.1.1.1 red: 56(84) bytes of data.
64 bytes from 1.1.1.1: icmp_seq=1 ttl=64 time=0.136 ms
--- 1.1.1.1 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.136/0.136/0.136/0.000 ms
$ ping6 -c1 -I red 2100:1::1
ping6: Warning: source address might be selected on device other than red.
PING 2100:1::1(2100:1::1) from 2100:1::1 red: 56 data bytes
64 bytes from 2100:1::1: icmp_seq=1 ttl=64 time=0.167 ms
--- 2100:1::1 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.167/0.167/0.167/0.000 ms
$ ping6 -c1 -I red 1111::1
PING 1111::1(1111::1) from 1111:1::1 red: 56 data bytes
64 bytes from 1111::1: icmp_seq=1 ttl=64 time=0.187 ms
--- 1111::1 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.187/0.187/0.187/0.000 ms
This change also enables use of loopback address on the VRF device:
$ ip addr add dev red 127.0.0.1/8
$ ping -c1 -I red 127.0.0.1
PING 127.0.0.1 (127.0.0.1) from 127.0.0.1 red: 56(84) bytes of data.
64 bytes from 127.0.0.1: icmp_seq=1 ttl=64 time=0.058 ms
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Thu, 2 Jun 2016 20:15:12 +0000 (13:15 -0700)]
net: vrf: ipv6 support for local traffic to local addresses
Add support for locally originated traffic to VRF-local IPv6 addresses.
Similar to IPv4 a local dst is set on the skb and the packet is
reinserted with a call to netif_rx. With this patch, ping, tcp and udp
packets to a local IPv6 address are successfully routed:
$ ip addr show dev eth1
4: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master red state UP group default qlen 1000
link/ether 02:e0:f9:1c:b9:74 brd ff:ff:ff:ff:ff:ff
inet 10.100.1.1/24 brd 10.100.1.255 scope global eth1
valid_lft forever preferred_lft forever
inet6 2100:1::1/120 scope global
valid_lft forever preferred_lft forever
inet6 fe80::e0:f9ff:fe1c:b974/64 scope link
valid_lft forever preferred_lft forever
$ ping6 -c1 -I red 2100:1::1
ping6: Warning: source address might be selected on device other than red.
PING 2100:1::1(2100:1::1) from 2100:1::1 red: 56 data bytes
64 bytes from 2100:1::1: icmp_seq=1 ttl=64 time=0.098 ms
ip6_input is exported so the VRF driver can use it for the dst input
function. The dst_alloc function for IPv4 defaults to setting the input and
output functions; IPv6's does not. VRF does not need to duplicate the Rx path
so just export the ipv6 input function.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Thu, 2 Jun 2016 20:15:11 +0000 (13:15 -0700)]
net: vrf: ipv4 support for local traffic to local addresses
Add support for locally originated traffic to VRF-local addresses. If
destination device for an skb is the loopback or VRF device then set
its dst to a local version of the VRF cached dst_entry and call netif_rx
to insert the packet onto the rx queue - similar to what is done for
loopback. This patch handles IPv4 support; follow on patch handles IPv6.
With this patch, ping, tcp and udp packets to a local IPv4 address are
successfully routed:
$ ip addr show dev eth1
4: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master red state UP group default qlen 1000
link/ether 02:e0:f9:1c:b9:74 brd ff:ff:ff:ff:ff:ff
inet 10.100.1.1/24 brd 10.100.1.255 scope global eth1
valid_lft forever preferred_lft forever
inet6 2100:1::1/120 scope global
valid_lft forever preferred_lft forever
inet6 fe80::e0:f9ff:fe1c:b974/64 scope link
valid_lft forever preferred_lft forever
$ ping -c1 -I red 10.100.1.1
ping: Warning: source address might be selected on device other than red.
PING 10.100.1.1 (10.100.1.1) from 10.100.1.1 red: 56(84) bytes of data.
64 bytes from 10.100.1.1: icmp_seq=1 ttl=64 time=0.057 ms
This patch also enables use of IPv4 loopback address on the VRF device:
$ ip addr add dev red 127.0.0.1/8
$ ping -c1 -I red 127.0.0.1
PING 127.0.0.1 (127.0.0.1) from 127.0.0.1 red: 56(84) bytes of data.
64 bytes from 127.0.0.1: icmp_seq=1 ttl=64 time=0.058 ms
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Thu, 2 Jun 2016 20:15:10 +0000 (13:15 -0700)]
net: vrf: Minor refactoring for local address patches
Move the stripping of the ethernet header from is_ip_tx_frame into the
ipv4 and ipv6 outbound functions. If the packet is destined to a local
address the header is retained since the packet is sent back to netif_rx.
Collapse vrf_send_v4_prep into vrf_process_v4_outbound.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 6 Jun 2016 03:16:50 +0000 (23:16 -0400)]
Merge branch 'hv_netvsc-cleanups'
Vitaly Kuznetsov says:
====================
hv_netvsc: cleanup after untangling the pointer mess
Changes since v1:
- resend when net-next is open [David Miller]
- rebased to current net-next.
After we made traveling through our internal structures explicit it became
obvious that some functions take arguments they don't need just to do
redundant pointer travel and get to what they really need while their
callers already have the required information.
This is just a cleanup series with no functional changes intended. It
doesn't pretend to be complete, additional cleanup of other functions may
follow.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Vitaly Kuznetsov [Fri, 3 Jun 2016 15:51:02 +0000 (17:51 +0200)]
hv_netvsc: pass struct net_device to rndis_filter_set_offload_params()
The only caller rndis_filter_device_add() has 'struct net_device' pointer
already.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vitaly Kuznetsov [Fri, 3 Jun 2016 15:51:01 +0000 (17:51 +0200)]
hv_netvsc: pass struct net_device to rndis_filter_set_device_mac()
We unpack 'struct net_device' in netvsc_set_mac_addr() to get to
'struct hv_device' pointer which we use in rndis_filter_set_device_mac()
to get back to 'struct net_device'.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vitaly Kuznetsov [Fri, 3 Jun 2016 15:51:00 +0000 (17:51 +0200)]
hv_netvsc: pass struct netvsc_device to rndis_filter_{open, close}()
Both rndis_filter_open()/rndis_filter_close() use struct hv_device to
reach to struct netvsc_device only and all callers have it already.
While on it, rename net_device to nvdev in rndis_filter_open() as
net_device is misleading.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vitaly Kuznetsov [Fri, 3 Jun 2016 15:50:59 +0000 (17:50 +0200)]
hv_netvsc: introduce {net, hv}_device_to_netvsc_device() helpers
Make it easier to get 'struct netvsc_device' from 'struct net_device' and
'struct hv_device' by introducing inline helpers.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vitaly Kuznetsov [Fri, 3 Jun 2016 15:50:58 +0000 (17:50 +0200)]
hv_netvsc: remove redundant assignment in netvsc_recv_callback()
net_device_ctx is assigned in the very beginning of the function and 'net'
pointer doesn't change.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kubeček [Fri, 27 May 2016 15:53:52 +0000 (17:53 +0200)]
net: disable fragment reassembly if high_thresh is zero
Before commit
6d7b857d541e ("net: use lib/percpu_counter API for
fragmentation mem accounting"), setting the reassembly high threshold
to 0 prevented fragment reassembly as first fragment would be always
evicted before second could be added to the queue. While inefficient,
some users apparently relied on this method.
Since the commit mentioned above, a percpu counter is used for
reassembly memory accounting and high batch size avoids taking slow path
in most common scenarios. As a result, a whole full sized packet can be
reassembled without the percpu counter's main counter changing its value
so that even with high_thresh set to 0, fragmented packets can be still
reassembled and processed.
Add explicit check preventing reassembly if high threshold is zero.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 5 Jun 2016 01:32:46 +0000 (21:32 -0400)]
Merge branch 'hns-acpi'
Kejian Yan says:
====================
net: hns: add support of ACPI
This series adds HNS support of acpi. The routine will call some ACPI
helper functions, like acpi_dev_found() and acpi_evaluate_dsm(), which
are not included in other cases. In order to make system compile
successfully in other cases except ACPI, it needs to add relative stub
functions to linux/acpi.h. And we use device property functions instead
of serial helper functions to suport both DT and ACPI cases. And then
add the supports of ACPI for HNS.
change log:
v3->v4:
mii-id gets from dev-name instead of address
v2->v3:
1. add Review-by: Andy Shevchenko
2. fix the potential memory leak
v1 -> v2:
1. use acpi_dev_found() instead of acpi_match_device_ids() to check if
it is a acpi node.
2. use is_of_node() instead of IS_ENABLED() to check if it is a DT node.
3. split the patch("add support of acpi for hns-mdio") into two patches:
3.1 Move to use fwnode_handle
3.2 Add ACPI
4. add the patch which subject is dsaf misc operation method
5. fix the comments by Andy Shevchenko
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Kejian Yan [Fri, 3 Jun 2016 02:55:21 +0000 (10:55 +0800)]
net: hns: net: hns: enet adds support of acpi
Enet needs to get configration parameter by acpi. This patch
adds support of ACPI for enet. The configuration parameter will
be configed in BIOS.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kejian Yan [Fri, 3 Jun 2016 02:55:20 +0000 (10:55 +0800)]
net: hns: implement the miscellaneous operation by asl
The miscellaneous operation is implemented in BIOS, the kernel can call
_DSM method help to call the implementation in ACPI case. Here is a patch
to do that.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kejian Yan [Fri, 3 Jun 2016 02:55:19 +0000 (10:55 +0800)]
net: hns: register phy device in each mac initial sequence
In ACPI case, there is no interface to register phy device to mdio-bus.
Phy device has to be registered itself to mdio-bus, and then enet can
get the phy device's info so that it can config the phy-device to help
to trasmit and receive data.
HNS hardware topology is as below. The MDIO controller may control several
PHY-devices, and each PHY-device connects to a MAC device. PHY-devices
will register when each mac find PHY device in initial sequence.
cpu
|
|
-------------------------------------------
| | |
| | |
| dsaf |
MDIO | MDIO
| --------------------------- |
| | | | | |
| | | | | |
| MAC MAC MAC MAC |
| | | | | |
---- |-------- |-------- | | --------
|| || || ||
PHY PHY PHY PHY
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kejian Yan [Fri, 3 Jun 2016 02:55:18 +0000 (10:55 +0800)]
net: hns: dsaf adds support of acpi
Dsaf needs to get configuration parameter by ACPI, so this patch add
support of ACPI.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kejian Yan [Fri, 3 Jun 2016 02:55:17 +0000 (10:55 +0800)]
net: hns: add dsaf misc operation method
The misc operation for different hw platform may be different, if using
current implementation, it will add a new branch on each function for
every new hw platform, so we add a method for this operation.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kejian Yan [Fri, 3 Jun 2016 02:55:16 +0000 (10:55 +0800)]
net: hns: add uniform interface for phy connection
As device_node is only used by DT case, HNS needs to treat the other
cases including ACPI. It needs to use uniform ways to handle both of
DT and ACPI. This patch chooses phy_device, and of_phy_connect and
of_phy_attach are only used by DT case. It needs to use uniform interface
to handle that sequence by both DT and ACPI.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kejian Yan [Fri, 3 Jun 2016 02:55:15 +0000 (10:55 +0800)]
net: hns: enet specify a reference to dsaf by fwnode_handle
As device_node is only used by DT case, it is expected to find uniform
ways. So fwnode_handle is the suitable method.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux.git / log