kernel - Bring in evdev from FreeBSD

[dragonfly.git] / sys / config / LINT64

#
# X86_64_LINT -- config file for checking all the sources, tries to pull in
#	as much of the source tree as it can.
#
# $FreeBSD: src/sys/i386/conf/LINT,v 1.749.2.144 2003/06/04 17:56:59 sam Exp $
#
# See the kernconf(5) manual page for more information on the format of
# this file.
#
# NB: You probably don't want to try running a kernel built from this
# file.  Instead, you should start from X86_64_GENERIC, and add options
# from this file as required.
#

# These directives are mandatory.  The machine directive specifies the
# platform and the machine_arch directive specifies the cpu architecture.
#
platform	pc64
machine		x86_64
machine_arch	x86_64

#
# This is the ``identification'' of the kernel.  Usually this should
# be the same as the name of your kernel.
#
ident		X86_64_LINT

#
# The `maxusers' parameter controls the static sizing of a number of
# internal system tables by a formula defined in subr_param.c.  Setting
# maxusers to 0 will cause the system to auto-size based on physical
# memory.
#
maxusers	10

#
# The `makeoptions' parameter allows variables to be passed to the
# generated Makefile in the build area.
#
# CONF_CFLAGS gives some extra compiler flags that are added to ${CFLAGS}
# after most other flags.  Here we use it to inhibit use of non-optimal
# gcc builtin functions (e.g., memcmp).
#
# DEBUG happens to be magic.
# The following is equivalent to 'config -g KERNELNAME' and creates
# 'kernel.debug' compiled with -g debugging as well as a normal
# 'kernel'.  Use 'make install.debug' to install the debug kernel
# but that isn't normally necessary as the debug symbols are not loaded
# by the kernel and are not useful there anyway.
#
# KERNEL can be overridden so that you can change the default name of your
# kernel.
#
# MODULES_OVERRIDE can be used to limit modules built to a specific list.
#
# INSTALLSTRIPPED can be set to cause installkernel to install stripped
# kernels and modules rather than a kernel and modules with debug symbols.
#
# INSTALLSTRIPPEDMODULES can be set to allow a full debug kernel to be
# installed, but to strip the installed modules.
#
makeoptions	CONF_CFLAGS=-fno-builtin  #Don't allow use of memcmp, etc.
#makeoptions	DEBUG=-g		#Build kernel with gdb(1) debug symbols
#makeoptions	KERNEL=foo		#Build kernel "foo" and install "/foo"
# Only build those parts of the sound system I need.
#makeoptions	MODULES_OVERRIDE="sound/snd sound/pcm"
#makeoptions	INSTALLSTRIPPED=1
#makeoptions	INSTALLSTRIPPEDMODULES=1

#
# Certain applications can grow to be larger than the 128M limit
# that DragonFly initially imposes.  Below are some options to
# allow that limit to grow to 256MB, and can be increased further
# with changing the parameters.  MAXDSIZ is the maximum that the
# limit can be set to, and the DFLDSIZ is the default value for
# the limit.  MAXSSIZ is the maximum that the stack limit can be
# set to.  You might want to set the default lower than the max,
# and explicitly set the maximum with a shell command for processes
# that regularly exceed the limit like INND.
#
options 	MAXDSIZ="(256*1024*1024)"
options 	MAXSSIZ="(256*1024*1024)"
options 	DFLDSIZ="(256*1024*1024)"

#
# BLKDEV_IOSIZE sets the default block size used in user block
# device I/O.  Note that this value will be overridden by the label
# when specifying a block device from a label with a non-0
# partition blocksize.  The default is PAGE_SIZE.
#
options 	BLKDEV_IOSIZE=8192

# This allows you to actually store this configuration file into
# the kernel binary itself, where it may be later read by saying:
#    strings -n 3 /kernel | sed -n 's/^___//p' > MYKERNEL
#
options 	INCLUDE_CONFIG_FILE     # Include this file in kernel

#
# The root device and filesystem type can be compiled in;
# this provides a fallback option if the root device cannot
# be correctly guessed by the bootstrap code, or an override if
# the RB_DFLTROOT flag (-r) is specified when booting the kernel.
#
options 	ROOTDEVNAME=\"ufs:da0s2e\"

#####################################################################
# CPU OPTIONS

cpu		HAMMER_CPU

#
# Options for CPU features.
#
# CPU_DISABLE_AVX disables AVX instruction set.
#
options 	CPU_DISABLE_AVX

#####################################################################
# COMPATIBILITY OPTIONS

# Enable NDIS binary driver support
options 	NDISAPI
device		ndis

#
# These three options provide support for System V Interface
# Definition-style interprocess communication, in the form of shared
# memory, semaphores, and message queues, respectively.
#
# System V shared memory and tunable parameters
options 	SHMMIN=2	# min shared memory segment size (bytes)
options 	SHMMNI=33	# max number of shared memory identifiers
options 	SHMSEG=9	# max shared memory segments per process

# System V semaphores and tunable parameters
options 	SEMMAP=31	# amount of entries in semaphore map
options 	SEMMNI=11	# number of semaphore identifiers in the system
options 	SEMMNS=61	# number of semaphores in the system
options 	SEMMNU=31	# number of undo structures in the system
options 	SEMMSL=61	# max number of semaphores per id
options 	SEMOPM=101	# max number of operations per semop call
options 	SEMUME=11	# max number of undo entries per process

# System V message queues and tunable parameters
options 	MSGMNB=2049	# max characters per message queue
options 	MSGMNI=41	# max number of message queue identifiers
options 	MSGSEG=2049	# max number of message segments in the system
options 	MSGSSZ=16	# size of a message segment MUST be power of 2
options 	MSGTQL=41	# max amount of messages in the system

#####################################################################
# DEBUGGING OPTIONS

#
# Enable the kernel debugger.
#
options 	DDB

#
# Print a stack trace on kernel panic.
#
options 	DDB_TRACE

#
# Don't drop into DDB for a panic. Intended for unattended operation
# where you may want to drop to DDB from the console, but still want
# the machine to recover from a panic
#
options 	DDB_UNATTENDED

#
# If using GDB remote mode to debug the kernel, there's a non-standard
# extension to the remote protocol that can be used to use the serial
# port as both the debugging port and the system console.  It's non-
# standard and you're on your own if you enable it.  See also the
# "remotechat" variables in the DragonFly specific version of gdb.
#
options 	GDB_REMOTE_CHAT

#
# KTRACE enables the system-call tracing facility ktrace(2).
#
options 	KTRACE			#kernel tracing

#
# The INVARIANTS option is used in a number of source files to enable
# extra sanity checking of internal structures.  This support is not
# enabled by default because of the extra time it would take to check
# for these conditions, which can only occur as a result of
# programming errors.
#
options 	INVARIANTS

#
# The DIAGNOSTIC option is used to enable extra debugging information
# from some parts of the kernel.  As this makes everything more noisy,
# it is disabled by default.
#
options 	DIAGNOSTIC

#
# This option let some drivers co-exist that can't co-exist in a running
# system.  This is used to be able to compile all kernel code in one go for
# quality assurance purposes (like this file, which the option takes it name
# from.)
#
options 	COMPILING_LINT


# XXX - this doesn't belong here.
# Allow ordinary users to take the console - this is useful for X.
options 	UCONSOLE

#####################################################################
# NETWORKING OPTIONS

#
# Protocol families:
#  Only the INET (Internet) family is officially supported in DragonFly.
#  Source code for the NS (Xerox Network Service) is provided for amusement
#  value.
#
options 	INET			#Internet communications protocols
options 	INET6			#IPv6 communications protocols
options 	IPSEC			#IP security
options 	IPSEC_ESP		#IP security (crypto; define w/ IPSEC)
options 	IPSEC_DEBUG		#debug for IP security
#
# Set IPSEC_FILTERGIF to force packets coming through a gif tunnel
# to be processed by any configured packet filtering (ipfw).
# The default is that packets coming from a tunnel are _not_ processed;
# they are assumed trusted.
#
# Note that enabling this can be problematic as there are no mechanisms
# in place for distinguishing packets coming out of a tunnel (e.g. no
# encX devices as found on openbsd).
#
#options 	IPSEC_FILTERGIF		#filter ipsec packets from a tunnel

#
# Experimental IPsec implementation that uses the kernel crypto
# framework.  This cannot be configured together with IPSEC and
# (currently) supports only IPv4.  To use this you must also
# configure the crypto device (see below).  Note that with this
# you get all the IPsec protocols (e.g. there is no FAST_IPSEC_ESP).
# IPSEC_DEBUG is used, as above, to configure debugging support
# within the IPsec protocols.
#
#options 	FAST_IPSEC		#new IPsec

options 	MPLS			#Multi-Protocol Label Switching

#
# SMB/CIFS requester
# NETSMB enables support for SMB protocol, it requires LIBMCHAIN and LIBICONV
# options.
options 	NETSMB			#SMB/CIFS requester

# mchain library. It can be either loaded as KLD or compiled into kernel
options 	LIBMCHAIN		#mbuf management library

# netgraph(4). Enable the base netgraph code with the NETGRAPH option.
# Individual node types can be enabled with the corresponding option
# listed below; however, this is not strictly necessary as netgraph
# will automatically load the corresponding KLD module if the node type
# is not already compiled into the kernel. Each type below has a
# corresponding man page, e.g., ng_async(4).
options 	NETGRAPH		#netgraph(4) system
options 	NETGRAPH_ASYNC
options 	NETGRAPH_BPF
options 	NETGRAPH_BRIDGE
options 	NETGRAPH_CISCO
options 	NETGRAPH_ECHO
options		NETGRAPH_EIFACE
options 	NETGRAPH_ETHER
options		NETGRAPH_FEC
options 	NETGRAPH_FRAME_RELAY
options 	NETGRAPH_HOLE
options 	NETGRAPH_IFACE
options 	NETGRAPH_KSOCKET
options 	NETGRAPH_L2TP
options 	NETGRAPH_LMI
# MPPC compression requires proprietary files (not included)
#options 	NETGRAPH_MPPC_COMPRESSION
options 	NETGRAPH_MPPC_ENCRYPTION
options 	NETGRAPH_ONE2MANY
options 	NETGRAPH_PPP
options 	NETGRAPH_PPPOE
options 	NETGRAPH_PPTPGRE
options 	NETGRAPH_RFC1490
options 	NETGRAPH_SOCKET
options 	NETGRAPH_TEE
options 	NETGRAPH_TTY
options 	NETGRAPH_UI
options 	NETGRAPH_VJC

device		mn	# Munich32x/Falc54 Nx64kbit/sec cards.

#
# Network interfaces:
#  The `loop' pseudo-device is MANDATORY when networking is enabled.
#  The `ether' pseudo-device provides generic code to handle
#  Ethernets; it is MANDATORY when a Ethernet device driver is
#  configured.
#  The `sppp' pseudo-device serves a similar role for certain types
#  of synchronous PPP links.
#  The `sl' pseudo-device implements the Serial Line IP (SLIP) service.
#  The `bpf' pseudo-device enables the Berkeley Packet Filter.  Be
#  aware of the legal and administrative consequences of enabling this
#  option.  The number of devices determines the maximum number of
#  simultaneous BPF clients programs runnable.
#  The `disc' pseudo-device implements a minimal network interface,
#  which throws away all packets sent and never receives any.  It is
#  included for testing purposes.  This shows up as the 'ds' interface.
#  The `tun' pseudo-device implements (user-)ppp and nos-tun
#  The `gif' pseudo-device implements IPv6 over IP4 tunneling,
#  IPv4 over IPv6 tunneling, IPv4 over IPv4 tunneling and
#  IPv6 over IPv6 tunneling.
#  The `gre' device implements two types of IP4 over IP4 tunneling:
#  GRE and MOBILE, as specified in the RFC1701 and RFC2004.
#  The `stf' device implements 6to4 encapsulation.
#  The `ef' pseudo-device provides support for multiple ethernet frame types
#  specified via ETHER_* options. See ef(4) for details.
#
pseudo-device	ether			#Generic Ethernet
pseudo-device	vlan	1		#VLAN support
pseudo-device	bridge			#Bridging support
pseudo-device	sppp			#Generic Synchronous PPP
pseudo-device	loop			#Network loopback device
pseudo-device	bpf			#Berkeley packet filter
pseudo-device	disc			#Discard device (ds0, ds1, etc)
pseudo-device	tap			#Ethernet tunnel network interface
pseudo-device	tun			#Tunnel driver (ppp(8), nos-tun(8))
pseudo-device	sl	2		#Serial Line IP
pseudo-device	gre			#IP over IP tunneling

# for IPv6
pseudo-device	gif			#IPv6 and IPv4 tunneling
pseudo-device	stf			#6to4 IPv6 over IPv4 encapsulation

#
# Internet family options:
#
# MROUTING enables the kernel multicast packet forwarder, which works
# with mrouted(8).
#
# PIM enables Protocol Independent Multicast in the kernel.
# Requires MROUTING enabled.
#
# IPFIREWALL enables support for IP firewall construction, in
# conjunction with the `ipfw' program.  IPFIREWALL_VERBOSE sends
# logged packets to the system logger.  IPFIREWALL_VERBOSE_LIMIT
# limits the number of times a matching entry can be logged.
#
# WARNING:  IPFIREWALL defaults to a policy of "deny ip from any to any"
# and if you do not add other rules during startup to allow access,
# YOU WILL LOCK YOURSELF OUT.  It is suggested that you set firewall_type=open
# in /etc/rc.conf when first enabling this feature, then refining the
# firewall rules in /etc/rc.firewall after you've tested that the new kernel
# feature works properly.
#
# IPFIREWALL3 is based on a newer version of FreeBSD's ipfw2, along with
# some enhancements. See ipfw3(4).
#
# IPFIREWALL_DEFAULT_TO_ACCEPT causes the default rule (at boot) to
# allow everything.  Use with care, if a cracker can crash your
# firewall machine, they can get to your protected machines.  However,
# if you are using it as an as-needed filter for specific problems as
# they arise, then this may be for you.  Changing the default to 'allow'
# means that you won't get stuck if the kernel and /sbin/ipfw binary get
# out of sync.
#
# IPDIVERT enables the divert IP sockets, used by ``ipfw divert''
#
# IPSTEALTH enables code to support stealth forwarding (i.e., forwarding
# packets without touching the ttl).  This can be useful to hide firewalls
# from traceroute and similar tools.
#
# TCPDEBUG is undocumented.
#
# ICMPPRINTFS enables ICMP to do extra debug prints.
#
options 	MROUTING		# Multicast routing
options 	PIM			# Protocol Independent Multicast
options 	IPFIREWALL		#firewall
options		IPFIREWALL_DEBUG	#debug prints
options 	IPFIREWALL_VERBOSE	#enable logging to syslogd(8)
options 	IPFIREWALL_VERBOSE_LIMIT=100	#limit verbosity
options 	IPFIREWALL_DEFAULT_TO_ACCEPT	#allow everything by default
options 	IPV6FIREWALL		#firewall for IPv6
options 	IPV6FIREWALL_VERBOSE
options 	IPV6FIREWALL_VERBOSE_LIMIT=100
options 	IPV6FIREWALL_DEFAULT_TO_ACCEPT
options 	IPDIVERT		#divert sockets
options 	IPSTEALTH		#support for stealth forwarding
options 	TCPDEBUG
options		ICMPPRINTFS

options		IPFIREWALL3

device		pf
device		pflog

#CARP
pseudo-device carp
options CARP

# The MBUF_STRESS_TEST option enables options which create
# various random failures / extreme cases related to mbuf
# functions.  See the mbuf(9) manpage for a list of available
# test cases.
options         MBUF_STRESS_TEST

# Statically link in accept filters
options                ACCEPT_FILTER_DATA
options                ACCEPT_FILTER_HTTP

# TCP_SIGNATURE adds support for RFC 2385 (TCP-MD5) digests. These are
# carried in TCP option 19. This option is commonly used to protect
# TCP sessions (e.g. BGP) where IPSEC is not available nor desirable.
# This is enabled on a per-socket basis using the TCP_SIGNATURE_ENABLE
# socket option.
# This requires the use of 'device crypto', 'options IPSEC'
# or 'device cryptodev'.
options   TCP_SIGNATURE   #include support for RFC 2385

#
# TCP_DROP_SYNFIN adds support for ignoring TCP packets with SYN+FIN. This
# prevents nmap et al. from identifying the TCP/IP stack, but breaks support
# for RFC1644 extensions and is not recommended for web servers.
#
options 	TCP_DROP_SYNFIN		#drop TCP packets with SYN+FIN

# ICMP_BANDLIM enables icmp error response bandwidth limiting.   You
# typically want this option as it will help protect the machine from
# D.O.S. packet attacks.
#
options 	ICMP_BANDLIM

# DUMMYNET enables the "dummynet" bandwidth limiter. You need
# IPFIREWALL as well. See the dummynet(4) and ipfw(8) manpages for more info.
#
options 	DUMMYNET
options		DUMMYNET_DEBUG

# IFPOLL_ENABLE adds support for mixed interrupt-polling handling
# of network device drivers, which has significant benefits in terms
# of robustness to overloads and responsivity, as well as permitting
# accurate scheduling of the CPU time between kernel network processing
# and other activities. The drawback is a moderate (up to 1/pollhz seconds)
# potential increase in response times. See polling(4) for further details.
#
# IFPOLL_ENABLE adds hardware queues' based polling
options		IFPOLL_ENABLE

#####################################################################
# FILESYSTEM OPTIONS

#
# Only the root, /usr, and /tmp filesystems need be statically
# compiled; everything else will be automatically loaded at mount
# time.  (Exception: the UFS family --- FFS, and MFS ---
# cannot currently be demand-loaded.)  Some people still prefer
# to statically compile other filesystems as well.
#

# One of these is mandatory:
options 	FFS			#Fast filesystem
options 	MFS			#Memory filesystem
options 	NFS			#Network filesystem

# The rest are optional:
#options 	NFS_NOSERVER		#Disable the NFS-server code.
options 	AUTOFS			#Automounter filesystem
options 	CD9660			#ISO 9660 filesystem
options		HAMMER			#HAMMER filesystem
options		HAMMER2			#HAMMER2 filesystem
options 	HPFS			#OS/2 File system
options 	MSDOSFS			#MS DOS filesystem
options 	NTFS			#NT filesystem
options 	NULLFS			#NULL filesystem
options 	PROCFS			#Process filesystem
options		PUFFS			#Userspace file systems (e.g. ntfs-3g & sshfs)
options 	SMBFS			#SMB/CIFS filesystem
options 	TMPFS			#Temporary filesystem
options		UDF			#UDF filesystem

# The xFS_ROOT options REQUIRE the associated ``options xFS''
options 	NFS_ROOT		#NFS usable as root device

# Soft updates is technique for improving UFS filesystem speed and
# making abrupt shutdown less risky.
options 	SOFTUPDATES

# Directory hashing improves the speed of operations on very large
# directories at the expense of some memory.
options 	UFS_DIRHASH

# Make space in the kernel for a root filesystem on a md device.
# Define to the number of kilobytes to reserve for the filesystem.
options 	MD_ROOT_SIZE=10

# Make the md device a potential root device, either with preloaded
# images of type mfs_root or md_root.
options 	MD_ROOT

# Specify double the default maximum size for malloc(9)-backed md devices.
options 	MD_NSECT=40000

# Allow this many swap-devices.
#
# In order to manage swap, the system must reserve bitmap space that
# scales with the largest mounted swap device multiplied by NSWAPDEV,
# regardless of whether other swap devices exist or not.  So it
# is not a good idea to make this value too large.
options 	NSWAPDEV=5

# Disk quotas are supported when this option is enabled.
options 	QUOTA			#enable disk quotas

# If you are running a machine just as a fileserver for PC and MAC
# users, e.g. using SAMBA, you may consider setting this option
# and keeping all those users' directories on a filesystem that is
# mounted with the suiddir option. This gives new files the same
# ownership as the directory (similar to group). It's a security hole
# if you let these users run programs, so confine it to file-servers
# (but it'll save you lots of headaches in those cases). Root owned
# directories are exempt and X bits are cleared. The suid bit must be
# set on the directory as well; see chmod(1) PC owners can't see/set
# ownerships so they keep getting their toes trodden on. This saves
# you all the support calls as the filesystem it's used on will act as
# they expect: "It's my dir so it must be my file".
#
options 	SUIDDIR

# NFS options:
options 	NFS_MINATTRTIMO=3	# VREG attrib cache timeout in sec
options 	NFS_MAXATTRTIMO=60
options 	NFS_MINDIRATTRTIMO=30	# VDIR attrib cache timeout in sec
options 	NFS_MAXDIRATTRTIMO=60
options 	NFS_GATHERDELAY=10	# Default write gather delay (msec)
options 	NFS_UIDHASHSIZ=29	# Tune the size of nfssvc_sock with this
options 	NFS_WDELAYHASHSIZ=16	# and with this
options 	NFS_MUIDHASHSIZ=63	# Tune the size of nfsmount with this
options 	NFS_DEBUG		# Enable NFS Debugging

# NTFS options:
options		NTFS_DEBUG

# MSDOSFS options:
options		MSDOSFS_DEBUG		# Enable MSDOSFS Debugging

#
# Add support for the EXT2FS filesystem of Linux fame.  Be a bit
# careful with this - the ext2fs code has a tendency to lag behind
# changes and not be exercised very much, so mounting read/write could
# be dangerous (and even mounting read only could result in panics.)
#
options 	EXT2FS

# Optional character code conversion support with LIBICONV.
# Each option requires their base file system and LIBICONV.
options 	CD9660_ICONV
options 	MSDOSFS_ICONV
options 	NTFS_ICONV

#####################################################################
# POSIX P1003.1B

# Real time extensions added in the 1993 Posix
# _KPOSIX_PRIORITY_SCHEDULING: Build in _POSIX_PRIORITY_SCHEDULING

options 	_KPOSIX_PRIORITY_SCHEDULING

#####################################################################
# CLOCK OPTIONS

# The granularity of operation is controlled by the kernel option HZ whose
# default value (100) means a granularity of 10ms (1s/HZ).
# Consider, however, that reducing the granularity too much might
# cause excessive overhead in clock interrupt processing,
# potentially causing ticks to be missed and thus actually reducing
# the accuracy of operation.

options 	HZ=100

#####################################################################
# SCSI DEVICES

# SCSI DEVICE CONFIGURATION

# The SCSI subsystem consists of the `base' SCSI code, a number of
# high-level SCSI device `type' drivers, and the low-level host-adapter
# device drivers.  The host adapters are listed in the ISA and PCI
# device configuration sections below.
#
# Beginning with FreeBSD 2.0.5 you can wire down your SCSI devices so
# that a given bus, target, and LUN always come on line as the same
# device unit.  In earlier versions the unit numbers were assigned
# in the order that the devices were probed on the SCSI bus.  This
# means that if you removed a disk drive, you may have had to rewrite
# your /etc/fstab file, and also that you had to be careful when adding
# a new disk as it may have been probed earlier and moved your device
# configuration around.

# This old behavior is maintained as the default behavior.  The unit
# assignment begins with the first non-wired down unit for a device
# type.  For example, if you wire a disk as "da3" then the first
# non-wired disk will be assigned da4.

# The syntax for wiring down devices is:

# device	scbus0 at ahc0		# Single bus device
# device	scbus1 at ahc1 bus 0	# Single bus device
# device	scbus3 at ahc2 bus 0	# Twin bus device
# device	scbus2 at ahc2 bus 1	# Twin bus device
# device 	da0 at scbus0 target 0 unit 0
# device	da1 at scbus3 target 1
# device	da2 at scbus2 target 3
# device	sa1 at scbus1 target 6
# device	cd

# "units" (SCSI logical unit number) that are not specified are
# treated as if specified as LUN 0.

# All SCSI devices allocate as many units as are required.

# The "unknown" device (uk? in pre-2.0.5) is now part of the base SCSI
# configuration and doesn't have to be explicitly configured.

device		scbus			#base SCSI code
device		ch			#SCSI media changers
device		da			#SCSI direct access devices (aka disks)
device		sa			#SCSI tapes
device		cd			#SCSI CD-ROMs
device		pass			#CAM passthrough driver
device		sg			#Passthrough device (linux scsi generic)
device		pt			#SCSI processor type
device		ses			#SCSI SES/SAF-TE driver
device		targ			#SCSI Target Mode Code
device		targbh			#SCSI Target Mode Blackhole Device

# Options for device mapper
device		dm
device		dm_target_crypt
device		dm_target_linear
device		dm_target_striped
device		dm_target_delay
device		dm_target_flakey

# Options for iSCSI
device	        iscsi_initiator
options		ISCSI_INITIATOR_DEBUG=8

# CAM OPTIONS:
# debugging options:
# -- NOTE --  If you specify one of the bus/target/lun options, you must
#             specify them all!
# CAMDEBUG: When defined enables debugging macros
# CAM_DEBUG_BUS:  Debug the given bus.  Use -1 to debug all busses.
# CAM_DEBUG_TARGET:  Debug the given target.  Use -1 to debug all targets.
# CAM_DEBUG_LUN:  Debug the given lun.  Use -1 to debug all luns.
# CAM_DEBUG_FLAGS:  OR together CAM_DEBUG_INFO, CAM_DEBUG_TRACE,
#                   CAM_DEBUG_SUBTRACE, and CAM_DEBUG_CDB
#
# CAM_MAX_HIGHPOWER: Maximum number of concurrent high power (start unit) cmds
# SCSI_NO_SENSE_STRINGS: When defined disables sense descriptions
# SCSI_NO_OP_STRINGS: When defined disables opcode descriptions
# SCSI_DELAY: The number of MILLISECONDS to freeze the SIM (scsi adapter)
#             queue after a bus reset, and the number of milliseconds to
#             freeze the device queue after a bus device reset.  This
#             can be changed at boot and runtime with the
#             kern.cam.scsi_delay tunable/sysctl.
options 	CAMDEBUG
options 	CAM_DEBUG_BUS=-1
options 	CAM_DEBUG_TARGET=-1
options 	CAM_DEBUG_LUN=-1
options 	CAM_DEBUG_FLAGS="CAM_DEBUG_INFO|CAM_DEBUG_TRACE|CAM_DEBUG_CDB"
options 	CAM_MAX_HIGHPOWER=4
options 	SCSI_NO_SENSE_STRINGS
options 	SCSI_NO_OP_STRINGS
options 	SCSI_DELAY=8000	# Be pessimistic about Joe SCSI device

# Options for the CAM CDROM driver:
# CHANGER_MIN_BUSY_SECONDS: Guaranteed minimum time quantum for a changer LUN
# CHANGER_MAX_BUSY_SECONDS: Maximum time quantum per changer LUN, only
#                           enforced if there is I/O waiting for another LUN
# The compiled in defaults for these variables are 2 and 10 seconds,
# respectively.
#
# These can also be changed on the fly with the following sysctl variables:
# kern.cam.cd.changer.min_busy_seconds
# kern.cam.cd.changer.max_busy_seconds
#
options 	CHANGER_MIN_BUSY_SECONDS=2
options 	CHANGER_MAX_BUSY_SECONDS=10

# Options for the CAM sequential access driver:
# SA_IO_TIMEOUT: Timeout for read/write/wfm  operations, in minutes
# SA_SPACE_TIMEOUT: Timeout for space operations, in minutes
# SA_REWIND_TIMEOUT: Timeout for rewind operations, in minutes
# SA_ERASE_TIMEOUT: Timeout for erase operations, in minutes
# SA_1FM_AT_EOD: Default to model which only has a default one filemark at EOT.
options 	SA_IO_TIMEOUT="(4)"
options 	SA_SPACE_TIMEOUT="(60)"
options 	SA_REWIND_TIMEOUT="(2*60)"
options 	SA_ERASE_TIMEOUT="(4*60)"
options 	SA_1FM_AT_EOD

# Optional timeout for the CAM processor target (pt) device
# This is specified in seconds.  The default is 60 seconds.
options 	SCSI_PT_DEFAULT_TIMEOUT="60"

# Optional enable of doing SES passthrough on other devices (e.g., disks)
#
# Normally disabled because a lot of newer SCSI disks report themselves
# as having SES capabilities, but this can then clot up attempts to build
# build a topology with the SES device that's on the box these drives
# are in....
options 	SES_ENABLE_PASSTHROUGH

#####################################################################
# MISCELLANEOUS DEVICES AND OPTIONS

# The `pty' device usually turns out to be ``effectively mandatory'',
# as it is required for `telnetd', `rlogind', `screen', `emacs', and
# `xterm', among others.

pseudo-device	pty		# Pseudo ttys
pseudo-device	gzip		# Exec gzipped a.out's
pseudo-device	md		# Memory/malloc disk
pseudo-device	vn		# File image "disks"
pseudo-device	putter		# for puffs and pud
pseudo-device	snp		# Snoop device - to look at pty/vty/etc..
pseudo-device	ccd	4	# Concatenated disk driver

# Configuring Vinum into the kernel is not necessary, since the kld
# module gets started automatically when vinum(8) starts.  This
# device is also untested.  Use at your own risk.
#
# The option VINUMDEBUG must match the value set in CFLAGS
# in src/sbin/vinum/Makefile.  Failure to do so will result in
# the following message from vinum(8):
#
# Can't get vinum config: Invalid argument
#
# see vinum(4) for more reasons not to use these options.
pseudo-device	vinum		#Vinum concat/mirror/raid driver
options 	VINUMDEBUG	#enable Vinum debugging hooks

# Kernel side iconv library
options 	LIBICONV

# Size of the kernel message buffer.  Should be N * pagesize.
options 	MSGBUF_SIZE=40960

#####################################################################
# HARDWARE DEVICE CONFIGURATION

# ISA devices:

#
# Mandatory ISA devices: isa
#
device		isa

#
# Options for `isa':
#
# AUTO_EOI_1 enables the `automatic EOI' feature for the master 8259A
# interrupt controller.  This saves about 0.7-1.25 usec for each interrupt.
# This option breaks suspend/resume on some portables.
#
# AUTO_EOI_2 enables the `automatic EOI' feature for the slave 8259A
# interrupt controller.  This saves about 0.7-1.25 usec for each interrupt.
# Automatic EOI is documented not to work for the slave with the
# original i8259A, but it works for some clones and some integrated
# versions.
#
# MAXMEM specifies the amount of RAM on the machine; if this is not
# specified, DragonFly will first read the amount of memory from the CMOS
# RAM, so the amount of memory will initially be limited to 64MB or 16MB
# depending on the BIOS.  If the BIOS reports 64MB, a memory probe will
# then attempt to detect the installed amount of RAM.  If this probe
# fails to detect >64MB RAM you will have to use the MAXMEM option.
# The amount is in kilobytes, so for a machine with 128MB of RAM, it would
# be 131072 (128 * 1024).
#
# BROKEN_KEYBOARD_RESET disables the use of the keyboard controller to
# reset the CPU for reboot.  This is needed on some systems with broken
# keyboard controllers.

options 	AUTO_EOI_1
#options 	AUTO_EOI_2
options 	MAXMEM="(128*1024)"
#options 	BROKEN_KEYBOARD_RESET

# Enable support for the kernel PLL to use an external PPS signal,
# under supervision of [x]ntpd(8)
# More info in ntpd documentation: http://www.eecis.udel.edu/~ntp

options 	PPS_SYNC

# The keyboard controller; it controls the keyboard and the PS/2 mouse.
device		atkbdc0	at isa? port IO_KBD

# The AT keyboard
device		atkbd0	at atkbdc? irq 1

# Options for atkbd:
options 	ATKBD_DFLT_KEYMAP	# specify the built-in keymap
makeoptions	ATKBD_DFLT_KEYMAP="jp.106"

# These options are valid for other keyboard drivers as well.
options 	KBD_DISABLE_KEYMAP_LOAD	# refuse to load a keymap
options 	KBD_INSTALL_CDEV	# install a CDEV entry in /dev

# `flags' for atkbd:
#       0x01    Force detection of keyboard, else we always assume a keyboard
#       0x02    Don't reset keyboard, useful for some newer ThinkPads
#	0x03	Force detection and avoid reset, might help with certain
#		dockingstations
#       0x04    Old-style (XT) keyboard support, useful for older ThinkPads

# PS/2 mouse
device		psm0	at atkbdc? irq 12

# Options for psm:
options 	PSM_HOOKRESUME		#hook the system resume event, useful
					#for some laptops
options 	PSM_RESETAFTERSUSPEND	#reset the device at the resume event

device		kbdmux			# keyboard multiplexer

# The video card driver.
device		vga0	at isa?

# Options for vga:
options		VGA_DEBUG=2		# enable VGA debug output

# If you experience problems switching back to 80x25 (or a derived mode),
# the following option might help.
#options	VGA_KEEP_POWERON_MODE	# use power-on settings for 80x25

# If you can dispense with some vga driver features, you may want to
# use the following options to save some memory.
#options 	VGA_NO_FONT_LOADING	# don't save/load font
#options 	VGA_NO_MODE_CHANGE	# don't change video modes

# The following option probably won't work with the LCD displays.
options 	VGA_WIDTH90		# support 90 column modes

# Splash screen at start up!  Screen savers require this too.
pseudo-device	splash

# The syscons console driver (sco color console compatible).
device		sc0	at isa?
options 	MAXCONS=16		# number of virtual consoles
options 	SC_ALT_MOUSE_IMAGE	# simplified mouse cursor in text mode
options 	SC_DEBUG_LEVEL=5	# enable debug output
options 	SC_DFLT_FONT		# compile font in
makeoptions	SC_DFLT_FONT=cp850
options 	SC_DISABLE_DDBKEY	# disable `debug' key
options 	SC_DISABLE_REBOOT	# disable reboot key sequence
options 	SC_HISTORY_SIZE=200	# number of history buffer lines
options 	SC_MOUSE_CHAR=0x3	# char code for text mode mouse cursor
options 	SC_PIXEL_MODE		# add support for the raster text mode

# The following options will let you change the default colors of syscons.
options 	SC_NORM_ATTR="(FG_GREEN|BG_BLACK)"
options 	SC_NORM_REV_ATTR="(FG_YELLOW|BG_GREEN)"
options 	SC_KERNEL_CONS_ATTR="(FG_RED|BG_BLACK)"
options 	SC_KERNEL_CONS_REV_ATTR="(FG_BLACK|BG_RED)"
options 	SC_BORDER_COLOR="FG_BLACK"

# If you have a two button mouse, you may want to add the following option
# to use the right button of the mouse to paste text.
options 	SC_TWOBUTTON_MOUSE

# You can selectively disable features in syscons.
#options 	SC_NO_CUTPASTE
#options 	SC_NO_FONT_LOADING
#options 	SC_NO_HISTORY
#options 	SC_NO_SYSMOUSE

#
# SCSI host adapters
#
# adv: All Narrow SCSI bus AdvanSys controllers.
# adw: Second Generation AdvanSys controllers including the ADV940UW.
# bt: Most Buslogic controllers
#
# Note that the order is important in order for Buslogic cards to be
# probed correctly.
#

device		bt
device		adv
device		adw

#
# Adaptec FSA RAID controllers, including integrated DELL controller,
# the Dell PERC 2/QC and the HP NetRAID-4M
#
device		aac
options		AAC_DEBUG
device		aacp	# SCSI Passthrough interface (optional, CAM required)

#
# Compaq Smart RAID, Mylex DAC960 and AMI MegaRAID controllers.  Only
# one entry is needed; the code will find and configure all supported
# controllers.
#
device		ida		# Compaq Smart RAID
device		mlx		# Mylex DAC960
device		amr		# AMI MegaRAID
device		amrp		# SCSI Passthrough interface (optional, CAM req.)
options		AMR_DEBUG=3
device		mfi		# LSI MegaRAID SAS
device		mfip		# LSI MegaRAID SAS passthrough, requires CAM
options 	MFI_DEBUG

#
# LSI MegaRAID 6Gb/s and 12Gb/s SAS+SATA RAID controller driver
#
device		mrsas

#
# Areca RAID (CAM is required).
#
device		arcmsr		# Areca SATA II RAID

#
# Highpoint RocketRAID 182x.
device		hptmv

#
# Highpoint RocketRAID.  Supports RR172x, RR222x, RR2240, RR232x, RR2340,
# RR2210, RR174x, RR2522, RR231x, RR230x.
device		hptrr

#
# Highpoint RocketRAID 27xx.
device		"hpt27xx"

#
# Highpoint RocketRaid 3xxx series SATA RAID
device		hptiop

#
# 3ware ATA RAID
#
device		twe		# 3ware ATA RAID
device		twa		# 3ware 9000 series PATA/SATA RAID
options 	TWA_DEBUG=10	# enable debug messages
device		tws		# 3ware 9750 series SATA/SAS RAID

#
# IBM ServeRAID
#
device	ips

# AHCI driver, this will override NATA for AHCI devices,
# both drivers may be included.
#
device		ahci

# NVME driver
#
device          nvme

# SiI3124/3132 driver
#
device		sili

# The 'NATA' driver supports all ATA and ATAPI devices.
# You only need one "device nata" for it to find all
# PCI ATA/ATAPI devices on modern machines.
#
device		nata
device		natadisk	# ATA disk drives
device		natapicd	# ATAPI CD/DVD drives
device		natapifd	# ATAPI floppy drives
device		natapist	# ATAPI tape drives
device		natapicam	# ATAPI CAM layer emulation
device		nataraid	# support for ATA software RAID controllers

# The following options are valid for the NATA driver:
#
# ATA_STATIC_ID:	controller numbering is static (like the old driver)
#			else the device numbers are dynamically allocated.
options 	ATA_STATIC_ID

# For older non-PCI systems, these are the lines to use:
#
#device		nata0	at isa? port IO_WD1 irq 14
#device		nata1	at isa? port IO_WD2 irq 15

#
# Standard floppy disk controllers: `fdc' and `fd' (see fdc(4))
#
device		fdc0	at isa? port IO_FD1 irq 6 drq 2
#
# FDC_DEBUG enables floppy debugging.  Since the debug output is huge, you
# gotta turn it actually on by setting the variable fd_debug with DDB,
# however.
options 	FDC_DEBUG

device		fd0	at fdc0 drive 0
device		fd1	at fdc0 drive 1

# LMC/SBE LMC1504 quad T1/E1 driver
#
device		musycc

#
# sio: serial ports (see sio(4))

device		sio0	at isa? port IO_COM1 flags 0x10 irq 4

#
# `flags' for serial drivers that support consoles (only for sio now):
#	0x10	enable console support for this unit.  The other console flags
#		are ignored unless this is set.  Enabling console support does
#		not make the unit the preferred console - boot with -h or set
#		the 0x20 flag for that.  Currently, at most one unit can have
#		console support; the first one (in config file order) with
#		this flag set is preferred.  Setting this flag for sio0 gives
#		the old behaviour.
#	0x20	force this unit to be the console (unless there is another
#		higher priority console).  This replaces the COMCONSOLE option.
#	0x40	reserve this unit for low level console operations.  Do not
#		access the device in any normal way.
#	0x80	use this port for serial line gdb support in ddb.
#

# Options for serial drivers that support consoles (only for sio now):
options 	BREAK_TO_DEBUGGER	#a BREAK on a comconsole goes to
					#DDB, if available.
options 	CONSPEED=115200		# speed for serial console
					# (default 9600)

# Solaris implements a new BREAK which is initiated by a character
# sequence CR ~ ^b which is similar to a familiar pattern used on
# Sun servers by the Remote Console.
options 	ALT_BREAK_TO_DEBUGGER

# Options for sio:
options 	COM_ESP			#code for Hayes ESP
options 	COM_MULTIPORT		#code for some cards with shared IRQs

# Other flags for sio that aren't documented in the man page.
#	0x20000	enable hardware RTS/CTS and larger FIFOs.  Only works for
#		ST16650A-compatible UARTs.

# PCI Universal Communications driver
# Supports various single and multi port PCI serial cards. Maybe later
# also the parallel ports on combination serial/parallel cards. New cards
# can be added in src/sys/dev/misc/puc/pucdata.c.
device		puc

#
# Network interfaces: `is', `lnc'
#
# lnc: Lance/PCnet cards (Isolan, Novell NE2100, NE32-VL, AMD Am7990 & Am79C960)
# sbsh: Granch SBNI16 SHDSL modem PCI adapters
# vmx: VMware VMXNET3 Ethernet (BSD open source)
# wi: Lucent WaveLAN/IEEE 802.11 PCMCIA adapters. Note: this supports both
#     the PCMCIA and ISA cards: the ISA card is really a PCMCIA to ISA
#     bridge with a PCMCIA adapter plugged into it.
# xe: Xircom/Intel EtherExpress Pro100/16 PC Card ethernet controller.
#
device lnc
device sln
device sn

# Wlan support is mandatory for some wireless LAN devices.
options 	IEEE80211_DEBUG		#enable debugging msgs
options 	IEEE80211_SUPPORT_MESH	#enable 802.11s D3.0 support
options 	IEEE80211_SUPPORT_TDMA	#enable TDMA support
device		wlan		# 802.11 support
device		wlan_acl	# 802.11 MAC-based access control for AP
device		wlan_ccmp	# 802.11 CCMP support
device		wlan_tkip	# 802.11 TKIP support
device		wlan_wep	# 802.11 WEP support
device		wlan_xauth	# 802.11 WPA or 802.1x authentication for AP
device		wlan_amrr	# 802.11 AMRR TX rate control algorithm
device		ath		# Atheros AR521x
options		AH_AR5416_INTERRUPT_MITIGATION
options		AH_ASSERT
options		AH_DEBUG
options		AH_INTERRUPT_DEBUGGING
options		AH_MAXCHAN=96
options		AH_NEED_DESC_SWAP
options		AH_PRIVATE_DIAG
options		AH_RXCFG_SDMAMW_4BYTES
options		AH_SUPPORT_AR5416
options		AH_SUPPORT_AR9130
options		AH_SUPPORT_AR9330
options		AH_SUPPORT_AR9340
options		AH_USE_INIPDGAIN
device		ath_hal		# Atheros Hardware Access Layer
#device		ath_rate_amrr	# Atheros AMRR TX rate control algorithm
#device		ath_rate_onoe	# Atheros Onoe TX rate control algorithm
device		ath_rate_sample	# Atheros Sample TX rate control algorithm
options		ATH_DEBUG	# turn on debugging output (see hw.ath.debug)
options		ATH_DIAGAPI	# diagnostic interface to the HAL
options		ATH_ENABLE_DFS
options		ATH_KTR_INTR_DEBUG
device		siba_bwn	# Sonic Inc. Silicon Backplane needed for bwn
options		SIBA_DEBUG	# turn on debugging output
device		bwn		# Broadcom BCM43xx NICs using v4 firmware
options		BWN_DEBUG	# turn on debugging output
options		BWN_RXRING_SLOTS=128	# number of RX slots to allocate
options		BWN_TXRING_SLOTS=128	# number of TX slots to allocate
device		iwi		# Intel PRO/Wireless 2200BG/2915ABG
device		iwm		# Intel Dual Band Wireless AC 316x/726x/826x
options		IWM_DEBUG	# turn on debugging output
device		iwn		# Intel WiFi Link 4965/1000/5000/5150/5300/6000/6050
options		IWN_DEBUG	# turn on debugging output
device		wi		# WaveLAN/IEEE, PRISM-II, Spectrum24 802.11DS
device		xe		# Xircom PCMCIA
device		ral		# Ralink Technology 802.11 wireless NIC
device		wpi
options		WPI_DEBUG	# turn on debugging output

# IEEE 802.11 adapter firmware modules

# iwifw:	Intel PRO/Wireless 2200BG/2225BG/2915ABG firmware
# iwmfw		Intel Dual Band Wireless AC 3160/3165/3168/7260/7265/8260/8265
# iwnfw:	Intel WiFi Link 4965/1000/5000/5150/5300/6000/6050
# ralfw:	Ralink Technology RT25xx and RT26xx firmware
# wpifw:	Intel 3945ABG Wireless LAN Controller firmware

device		iwifw
device		iwmfw
device		iwnfw
device		ralfw
device		wpifw

# Bluetooth Protocols
device		bluetooth

# Sound drivers
#

# Basic sound card support:
device		sound
# For PCI sound cards:
device		"snd_als4000"
device		"snd_atiixp"
device		"snd_cmi"
device		"snd_cs4281"
device		"snd_emu10k1"
device		"snd_emu10kx"
device		"snd_envy24"
device		"snd_envy24ht"
device		"snd_es137x"
device		"snd_fm801"
device		"snd_hda"
device		"snd_hdspe"
device		"snd_ich"
device		"snd_maestro"
device		"snd_neomagic"
device		"snd_solo"
device		"snd_spicds"
device		"snd_t4dwave"
device		"snd_via8233"
device		"snd_via82c686"
device		"snd_vibes"
# USB
device		"snd_uaudio"

#
# Following options are intended for debugging/testing purposes:
#
# SND_DEBUG                    Enable extra debugging code that includes
#                              sanity checking and possible increase of
#                              verbosity.
#
# SND_DIAGNOSTIC               Similar in a spirit of INVARIANTS/DIAGNOSTIC,
#                              zero tolerance against inconsistencies.
#
# SND_FEEDER_MULTIFORMAT       By default, only 16/32 bit feeders are compiled
#                              in. This options enable most feeder converters
#                              except for 8bit. WARNING: May bloat the kernel.
#
# SND_FEEDER_FULL_MULTIFORMAT  Ditto, but includes 8bit feeders as well.
#
# SND_FEEDER_RATE_HP           (feeder_rate) High precision 64bit arithmetic
#                              as much as possible (the default trying to
#                              avoid it). Possible slowdown.
#
# SND_PCM_64                   (Only applicable for i386/32bit arch)
#                              Process 32bit samples through 64bit
#                              integer/arithmetic. Slight increase of dynamic
#                              range at a cost of possible slowdown.
#
# SND_OLDSTEREO                Only 2 channels are allowed, effectively
#                              disabling multichannel processing.
#
options		SND_DEBUG
#options		SND_DIAGNOSTIC
options		SND_FEEDER_MULTIFORMAT
options		SND_FEEDER_FULL_MULTIFORMAT
options		SND_FEEDER_RATE_HP
options		SND_PCM_64
options		SND_OLDSTEREO

#
# Miscellaneous hardware:
#
# bktr: Brooktree bt848/848a/849a/878/879 video capture and TV Tuner board
# coremctl: Intel Core/E3 memory controller (required by ecc(4) and memtemp(4))
# dimm: Location inforamtion (required by ecc(4) and memtemp(4))
# ecc: ECC memory controller
# ipmi: Intelligent Platform Management Interface
# joy: joystick
# nrp: Comtrol Rocketport
# si: Specialix SI/XIO 4-32 port terminal multiplexor
# nmdm: nullmodem terminal driver (see nmdm(4))
# tpm: Trusted Platform Module

# Notes on the Specialix SI/XIO driver:
#  **This is NOT a Specialix supported Driver!**
#  The host card is memory, not IO mapped.
#  The Rev 1 host cards use a 64K chunk, on a 32K boundary.
#  The Rev 2 host cards use a 32K chunk, on a 32K boundary.
#  The cards can use an IRQ of 11, 12 or 15.

device		coremctl
device		dimm
device		ecc
device		joy0	at isa? port IO_GAME
device		nrp
device		si
# nullmodem terminal driver
device		nmdm
device		tpm
device		ipmi

# The adw driver will attempt to use memory mapped I/O for all PCI
# controllers that have it configured only if this option is set.
options 	ADW_ALLOW_MEMIO

#
# PCI devices & PCI options:
#
# The main PCI bus device is `pci'.  It provides auto-detection and
# configuration support for all devices on the PCI bus, using either
# configuration mode defined in the PCI specification.

device		pci

# AGP GART support
#
device		agp

#
# AGP debugging.
#
options                AGP_DEBUG

# The `amd' device provides support for the AMD 53C974 SCSI host
# adapter chip as found on devices such as the Tekram DC-390(T).
#
# The `bge' device provides support for gigabit ethernet adapters
# based on the Broadcom BCM570x family of controllers, including the
# 3Com 3c996-T, the Netgear GA302T, the SysKonnect SK-9D21 and SK-9D41,
# and the embedded gigE NICs on Dell PowerEdge 2550 servers.
#
# The `ncr' device provides support for the NCR 53C810 and 53C825
# self-contained SCSI host adapters.
#
# The `isp' device provides support for the Qlogic ISP 1020, 1040
# nd 1040B PCI SCSI host adapters, ISP 1240 Dual Ultra SCSI,
# ISP 1080 and 1280 (Dual) Ultra2, ISP 12160 Ultra3 SCSI, as well as
# the Qlogic ISP 2100 and ISP 2200 Fibre Channel Host Adapters.
#
# The `dc' device provides support for PCI fast ethernet adapters
# based on the DEC/Intel 21143 and various workalikes including:
# the ADMtek AL981 Comet and AN985 Centaur, the ASIX Electronics
# AX88140A and AX88141, the Davicom DM9100 and DM9102, the Lite-On
# 82c168 and 82c169 PNIC, the Lite-On/Macronix LC82C115 PNIC II
# and the Macronix 98713/98713A/98715/98715A/98725 PMAC. This driver
# replaces the old al, ax, dm, pn and mx drivers.  List of brands:
# Digital DE500-BA, Kingston KNE100TX, D-Link DFE-570TX, SOHOware SFA110,
# SVEC PN102-TX, CNet Pro110B, 120A, and 120B, Compex RL100-TX,
# LinkSys LNE100TX, LNE100TX V2.0, Jaton XpressNet, Alfa Inc GFC2204,
# KNE110TX.
#
# The `de' device provides support for the Digital Equipment DC21040
# self-contained Ethernet adapter.
#
# The `em' device provides support for the Intel Pro/1000 Family of Gigabit
# adapters (82542, 82543, 82544, 82540).
#
# The `et' device provides support for the Agere ET1310 10/100/1000 PCIe
# adapters.
#
# The `fxp' device provides support for the Intel EtherExpress Pro/100B
# PCI Fast Ethernet adapters.
#
# The 'lge' device provides support for PCI gigabit ethernet adapters
# based on the Level 1 LXT1001 NetCellerator chipset. This includes the
# D-Link DGE-500SX, SMC TigerCard 1000 (SMC9462SX), and some Addtron cards.
#
# The 'my' device provides support for the Myson MTD80X and MTD89X PCI
# Fast Ethernet adapters.
#
# The 'nge' device provides support for PCI gigabit ethernet adapters
# based on the National Semiconductor DP83820 and DP83821 chipset. This
# includes the SMC EZ Card 1000 (SMC9462TX), D-Link DGE-500T, Asante
# FriendlyNet GigaNIX 1000TA and 1000TPC, the Addtron AEG320T, the
# LinkSys EG1032 and EG1064, the Surecom EP-320G-TX and the Netgear GA622T.
#
# The 'oce' device provides support for Emulex 10 Gbit adapters
# (OneConnect Ethernet).
#
# The 'pcn' device provides support for PCI fast ethernet adapters based
# on the AMD Am79c97x chipsets, including the PCnet/FAST, PCnet/FAST+,
# PCnet/PRO and PCnet/Home. These were previously handled by the lnc
# driver (and still will be if you leave this driver out of the kernel).
#
# Te 're' device provides support for PCI GigaBit ethernet adapters based
# on the RealTek 8169 chipset. It also supports the 8139C+ and is the
# preferred driver for that chip.
#
# The 'rl' device provides support for PCI fast ethernet adapters based
# on the RealTek 8129/8139 chipset. Note that the RealTek driver defaults
# to using programmed I/O to do register accesses because memory mapped
# mode seems to cause severe lockups on SMP hardware. This driver also
# supports the Accton EN1207D `Cheetah' adapter, which uses a chip called
# the MPX 5030/5038, which is either a RealTek in disguise or a RealTek
# workalike.  Note that the D-Link DFE-530TX+ uses the RealTek chipset
# and is supported by this driver, not the 'vr' driver.
#
# The 'sf' device provides support for Adaptec Duralink PCI fast
# ethernet adapters based on the Adaptec AIC-6915 "starfire" controller.
# This includes dual and quad port cards, as well as one 100baseFX card.
# Most of these are 64-bit PCI devices, except for one single port
# card which is 32-bit.
#
# The 'ste' device provides support for adapters based on the Sundance
# Technologies ST201 PCI fast ethernet controller. This includes the
# D-Link DFE-550TX.
#
# The 'sis' device provides support for adapters based on the Silicon
# Integrated Systems SiS 900 and SiS 7016 PCI fast ethernet controller
# chips.
#
# The 'sk' device provides support for the SysKonnect SK-984x series
# PCI gigabit ethernet NICs. This includes the SK-9841 and SK-9842
# single port cards (single mode and multimode fiber) and the
# SK-9843 and SK-9844 dual port cards (also single mode and multimode).
# The driver will autodetect the number of ports on the card and
# attach each one as a separate network interface.
#
# The 'ti' device provides support for PCI gigabit ethernet NICs based
# on the Alteon Networks Tigon 1 and Tigon 2 chipsets. This includes the
# Alteon AceNIC, the 3Com 3c985, the Netgear GA620 and various others.
# Note that you will probably want to bump up NMBCLUSTERS a lot to use
# this driver.
#
# The 'tl' device provides support for the Texas Instruments TNETE100
# series 'ThunderLAN' cards and integrated ethernet controllers. This
# includes several Compaq Netelligent 10/100 cards and the built-in
# ethernet controllers in several Compaq Prosignia, Proliant and
# Deskpro systems. It also supports several Olicom 10Mbps and 10/100
# boards.
#
# The `tx' device provides support for the SMC 9432 TX, BTX and FTX cards.
#
# The `txp' device provides support for the 3Com 3cR990 "Typhoon"
# 10/100 adapters.
#
# The `vr' device provides support for various fast ethernet adapters
# based on the VIA Technologies VT3043 `Rhine I' and VT86C100A `Rhine II'
# chips, including the D-Link DFE530TX (see 'rl' for DFE530TX+), the Hawking
# Technologies PN102TX, and the AOpen/Acer ALN-320.
#
# The `wb' device provides support for various fast ethernet adapters
# based on the Winbond W89C840F chip. Note: this is not the same as
# the Winbond W89C940F, which is an NE2000 clone.
#
# The `xl' device provides support for the 3Com 3c900, 3c905 and
# 3c905B (Fast) Etherlink XL cards and integrated controllers. This
# includes the integrated 3c905B-TX chips in certain Dell Optiplex and
# Dell Precision desktop machines and the integrated 3c905-TX chips
# in Dell Latitude laptop docking stations.
#
# The 'bktr' device is a PCI video capture device using the Brooktree
# bt848/bt848a/bt849a/bt878/bt879 chipset. When used with a TV Tuner it forms a
# TV card, eg Miro PC/TV, Hauppauge WinCast/TV WinTV, VideoLogic Captivator,
# Intel Smart Video III, AverMedia, IMS Turbo, FlyVideo.
#
# options 	OVERRIDE_CARD=xxx
# options 	OVERRIDE_TUNER=xxx
# options 	OVERRIDE_MSP=1
# options 	OVERRIDE_DBX=1
# These options can be used to override the auto detection
# The current values for xxx are found in src/sys/dev/video/bktr/bktr_card.h
# Using sysctl(8) run-time overrides on a per-card basis can be made
#
# options 	BKTR_SYSTEM_DEFAULT=BROOKTREE_PAL
# or
# options 	BKTR_SYSTEM_DEFAULT=BROOKTREE_NTSC
# Specifies the default video capture mode.
# This is required for Dual Crystal (28&35Mhz) boards where PAL is used
# to prevent hangs during initialisation.  eg VideoLogic Captivator PCI.
#
# options 	BKTR_USE_PLL
# PAL or SECAM users who have a 28Mhz crystal (and no 35Mhz crystal)
# must enable PLL mode with this option. eg some new Bt878 cards.
#
# options 	BKTR_GPIO_ACCESS
# This enable IOCTLs which give user level access to the GPIO port.
#
# options 	BKTR_NO_MSP_RESET
# Prevents the MSP34xx reset. Good if you initialise the MSP in another OS first
#
# options 	BKTR_430_FX_MODE
# Switch Bt878/879 cards into Intel 430FX chipset compatibility mode.
#
# options 	BKTR_SIS_VIA_MODE
# Switch Bt878/879 cards into SIS/VIA chipset compatibility mode which is
# needed for some old SiS and VIA chipset motherboards.
# This also allows Bt878/879 chips to work on old OPTi (<1997) chipset
# motherboards and motherboards with bad or incomplete PCI 2.1 support.
# As a rough guess, old = before 1998
#
# options 	BKTR_NEW_MSP34XX_DRIVER
# Use new, more complete initialization scheme for the msp34* soundchip.
# Should fix stereo autodetection if the old driver does only output
# mono sound.
#
# options	BKTR_OVERRIDE_CARD=xxx
# options	BKTR_OVERRIDE_DBX=xxx
# options	BKTR_OVERRIDE_MSP=xxx
# options	BKTR_OVERRIDE_TUNER=xxx
# These options can be used to select a specific device, regardless of
# the autodetection and i2c device checks (see comments in bktr_card.c).
#
device		amd		# AMD 53C974 (Tekram DC-390(T))
device		isp		# Qlogic family
device		ispfw		# Firmware for QLogic HBAs
device		mpt		# LSI '909 FC adapters
device		mps		# LSI-Logic MPT-Fusion 2
device		ncr		# NCR/Symbios Logic
device		sym		# NCR/Symbios Logic (newer chipsets)
device		trm		# Tekram DC395U/UW/F and DC315U
#
# Options for ISP
#
#	ISP_TARGET_MODE		-	enable target mode operation
#options 	ISP_TARGET_MODE=1

# Options used in dev/disk/sym/ (Symbios SCSI driver).
#options 	SYM_SETUP_LP_PROBE_MAP	#-Low Priority Probe Map (bits)
					# Allows the ncr to take precedence
					# 1 (1<<0) -> 810a, 860
					# 2 (1<<1) -> 825a, 875, 885, 895
					# 4 (1<<2) -> 895a, 896, 1510d
#options 	SYM_SETUP_SCSI_DIFF	#-HVD support for 825a, 875, 885
					# disabled:0 (default), enabled:1
#options 	SYM_SETUP_PCI_PARITY	#-PCI parity checking
					# disabled:0, enabled:1 (default)
#options 	SYM_SETUP_MAX_LUN	#-Number of LUNs supported
					# default:8, range:[1..64]


# MII bus support is required for some PCI 10/100 ethernet NICs,
# namely those which use MII-compliant transceivers or implement
# transceiver control interfaces that operate like an MII. Adding
# "device miibus0" to the kernel config pulls in support for
# the generic miibus API and all of the PHY drivers, including a
# generic one for PHYs that aren't specifically handled by an
# individual driver.
device		miibus

# PCI Ethernet NICs that use the common MII bus controller code.
device		ae		# Attansic/Atheros L2 Fast Ethernet
device		alc		# Atheros AR8131/AR8132
device		ale		# Atheros AR8121/AR8113/AR8114
device		age		# Attansic/Atheros L1 Gigabit Ethernet
device		bce		# Broadcom NetXtreme II Gigabit Ethernet
device		bfe		# Broadcom BCM440x 10/100 Ethernet
device		bnx		# Broadcom NetXtreme 5718/57785 Gigabit Ethernet
device		dc		# DEC/Intel 21143 and various workalikes
device		fxp		# Intel EtherExpress PRO/100B (82557, 82558)
device		my		# Myson Fast Ethernet (MTD80X, MTD89X)
device		pcn		# AMD Am79C97x PCI 10/100 NICs
device		re		# RealTek 8139C+/8169
device		rl		# RealTek 8129/8139
device		sbsh		# Granch SBNI16 SHDSL modem
device		sf		# Adaptec AIC-6915 (``Starfire'')
device		sis		# Silicon Integrated Systems SiS 900/SiS 7016
device		ste		# Sundance ST201 (D-Link DFE-550TX)
device		tl		# Texas Instruments ThunderLAN
device		tx		# SMC EtherPower II (83c17x ``EPIC'')
device		vge		# VIA 612x GigE
device		vr		# VIA Rhine, Rhine II
device		wb		# Winbond W89C840F
device		xl		# 3Com 3c90x (``Boomerang'', ``Cyclone'')

# PCI Ethernet NICs.
device		de		# DEC/Intel DC21x4x (``Tulip'')
device		txp		# 3Com 3cR990 (``Typhoon'')

# Gigabit Ethernet NICs.
device		bge		# Broadcom BCM570x (``Tigon III'')
device		em		# Intel Pro/1000 (8254x,8257x)
				# Requires ig_hal
device		emx		# Intel Pro/1000 (8257{1,2,3,4})
				# Requires ig_hal
device		igb		# Intel Pro/1000 (82575, 82576, 82580, i350)
				# Requires ig_hal
device		ig_hal		# Intel Pro/1000 hardware abstraction layer
device		ix		# Intel PRO/10GbE PCIE Ethernet Family
device		et		# Agere ET1310 10/100/1000 Ethernet
device		lge		# Level 1 LXT1001 (``Mercury'')
device		mxge		# Myricom Myri-10G 10GbE NIC
device		mxgefw		# Firmware for Myricom Myri-10G 10GbE NIC
device		nfe		# nVidia nForce2/3 MCP04/51/55 CK804
device		nge		# NatSemi DP83820 and DP83821
device		oce		# Emulex 10 GbE (OneConnect Ethernet)
device		sk		# SysKonnect GEnesis, LinkSys EG1023, D-Link
device		ti		# Alteon (``Tigon I'', ``Tigon II'')
device		stge		# Sundance/Tamarack TC9021 Gigabit Ethernet
device		msk		# Marvell/SysKonnect Yukon II Gigabit Ethernet
device		jme		# JMicron Gigabit/Fast Ethernet

# Brooktree driver has been ported to the new I2C framework. Thus,
# you'll need to have the following 3 lines in the kernel config.
#     device smbus
#     device iicbus
#     device iicbb
# The iic and smb devices are only needed if you want to control other
# I2C slaves connected to the external connector of some cards.
#
device		bktr
options 	BKTR_NEW_MSP34XX_DRIVER

# WinTV PVR-250/350 driver
device		cxm

#
# PCCARD/PCMCIA
#
# pccard: pccard slots
# cardbus/cbb: cardbus bridge
device		pccard
device		cardbus
device		cbb

#
# MMC/SD
#
# mmc 		MMC/SD bus
# mmcsd		MMC/SD memory card
# sdhci		Generic PCI SD Host Controller
#
device		mmc
device		mmcsd
device		sdhci

#
# SMB bus
#
# System Management Bus support is provided by the 'smbus' device.
# Access to the SMBus device is via the 'smb' device (/dev/smb*),
# which is a child of the 'smbus' device.
#
# Supported devices:
# smb		standard io through /dev/smb*
#
# ACPI support:
# smbacpi	support for ACPI I2cSerialBus resources
#
# Supported SMB interfaces:
# iicsmb	I2C to SMB bridge with any iicbus interface
# bktr		brooktree848 I2C hardware interface
# intpm		Intel PIIX4 (82371AB, 82443MX) Power Management Unit
# alpm		Acer Aladdin-IV/V/Pro2 Power Management Unit
# ichiic	Intel generation 4 I2C controller
# ichsmb	Intel ICH SMBus controller chips (82801AA, 82801AB, 82801BA)
# viapm		VIA VT82C586B,596,686A and VT8233 SMBus controllers
# amdpm		AMD 756 Power Management Unit
# amdsmb	AMD 8111 SMBus 2.0 Controller
#
device		smbus		# Bus support, required for smb below.

device		intpm
device		alpm
device		ichiic
device		ichsmb
device		viapm
device		amdpm
device		amdsmb

device		smb

device		smbacpi

#
# I2C Bus
#
# Philips i2c bus support is provided by the `iicbus' device.
#
# Supported devices:
# ic	i2c network interface
# iic	i2c standard io
# iicsmb i2c to smb bridge. Allow i2c i/o with smb commands.
#
# Supported interfaces:
# pcf	Philips PCF8584 ISA-bus controller
# bktr	brooktree848 I2C software interface
#
# Other:
# iicbb	generic I2C bit-banging code (needed by lpbb, bktr)
#
device		iicbus		# Bus support, required for ic/iic/iicsmb below.
device		iicbb

device		ic
device		iic
device		iicsmb		# smb over i2c bridge

device		pcf0	at isa? port 0x320 irq 5

# Intel performance-energy bias
device		perfbias

# Intel software controlled clock modulation
device		clockmod

# Intel Sandy Bridge and newer CPUs power usage estimation
device		corepower

# Intel Core and newer CPUs on-die digital thermal sensor support
device		coretemp

# Memory thermal sensor
device		memtemp

# CPU control pseudo-device. Provides access to MSRs, CPUID info and
# microcode update feature.
device		cpuctl

# Effective CPU frequency interface via APERF/MPERF MSRs
device		aperf

# AMD Family 0Fh, 10h and 11h temperature sensors
device		kate
device		km

# ThinkPad Active Protection System accelerometer
device		aps0	at isa? port 0x1600

# HW monitoring devices lm(4), it(4) and nsclpcsio.
device		lm0	at isa? port 0x290
device		it0	at isa? port 0x290
device		it1	at isa? port 0xc00
device		it2	at isa? port 0xd00
device		it3	at isa?	port 0x228
device		nsclpcsio0 at isa? port 0x2e
device		nsclpcsio1 at isa? port 0x4e
device		wbsio0	at isa? port 0x2e
device		wbsio1	at isa? port 0x4e
device		uguru0	at isa? port 0xe0	# ABIT uGuru

# EFI Runtime Services support (not functional yet).
options 	EFIRT

# Parallel-Port Bus
#
# Parallel port bus support is provided by the `ppbus' device.
# Multiple devices may be attached to the parallel port, devices
# are automatically probed and attached when found.
#
# Supported devices:
# vpo	Iomega Zip Drive
#	Requires SCSI disk support ('scbus' and 'da'); the best
#	performance is achieved with ports in EPP 1.9 mode.
# lpt	Parallel Printer
# plip	Parallel network interface
# ppi	General-purpose I/O ("Geek Port") + IEEE1284 I/O
# pps	Pulse per second Timing Interface
# lpbb	Philips official parallel port I2C bit-banging interface
#
# Supported interfaces:
# ppc	ISA-bus parallel port interfaces.
#

options 	PPC_PROBE_CHIPSET # Enable chipset specific detection
				  # (see flags in ppc(4))
options 	DEBUG_1284	# IEEE1284 signaling protocol debug
options 	PERIPH_1284	# Makes your computer act as a IEEE1284
				# compliant peripheral
options 	DONTPROBE_1284	# Avoid boot detection of PnP parallel devices
options 	VP0_DEBUG	# ZIP/ZIP+ debug
options 	LPT_DEBUG	# Printer driver debug
options 	PPC_DEBUG=2	# Parallel chipset level debug
options 	PLIP_DEBUG	# Parallel network IP interface debug
options 	PCFCLOCK_VERBOSE         # Verbose pcfclock driver
options 	PCFCLOCK_MAX_RETRIES=5   # Maximum read tries (default 10)

device		ppc0	at isa? irq 7
device		ppbus
device		vpo
device		lpt
device		plip
device		ppi
device		pps
device		lpbb
device		pcfclock

# Kernel BOOTP support

options 	BOOTP		# Use BOOTP to obtain IP address/hostname
options 	BOOTP_NFSROOT	# NFS mount root filesystem using BOOTP info
options 	BOOTP_COMPAT	# Workaround for broken bootp daemons.
options 	BOOTP_WIRED_TO=fxp0 # Use interface fxp0 for BOOTP

#
# Set the number of PV entries per process.  Increasing this can
# stop panics related to heavy use of shared memory. However, that can
# (combined with large amounts of physical memory) cause panics at
# boot time due the kernel running out of VM space.
#
# If you're tweaking this, you might also want to increase the sysctls
# "vm.v_free_min", "vm.v_free_reserved", and "vm.v_free_target".
#
# The value below is the one more than the default.
#
options 	PMAP_SHPGPERPROC=201

#
# Disable swapping. This option removes all code which actually performs
# swapping, so it's not possible to turn it back on at run-time.
#
# This is sometimes usable for systems which don't have any swap space
# (see also sysctls "vm.defer_swapspace_pageouts" and
# "vm.disable_swapspace_pageouts")
#
#options 	NO_SWAPPING

# Set the size of the buffer cache KVM reservation, in buffers.  This is
# scaled by approximately 16384 bytes.  The system will auto-size the buffer
# cache if this option is not specified.
#
options 	NBUF=512

# Set the size of the mbuf KVM reservation, in clusters.  This is scaled
# by approximately 2048 bytes.  The system will auto-size the mbuf area
# to (512 + maxusers*16) if this option is not specified.
# maxusers is in turn computed at boot time depending on available memory
# or set to the value specified by "options MAXUSERS=x" (x=0 means
# autoscaling).
# So, to take advantage of autoscaling, you have to remove both
# NMBCLUSTERS and MAXUSERS (and NMBUFS) from your kernel config.
#
options 	NMBCLUSTERS=1024

# Set the number of mbufs available in the system. Each mbuf
# consumes 256 bytes. The system will autosize this (to 4 times
# the number of NMBCLUSTERS, depending on other constraints)
# if this option is not specified.
#
options 	NMBUFS=4096

# Tune the buffer cache maximum KVA reservation, in bytes.  The maximum is
# usually capped at 200 MB, effecting machines with > 1GB of ram.  Note
# that the buffer cache only really governs write buffering and disk block
# translations.  The VM page cache is our primary disk cache and is not
# effected by the size of the buffer cache.
#
options 	VM_BCACHE_SIZE_MAX="(100*1024*1024)"

# Tune the swap zone KVA reservation, in bytes.  The default is typically
# 70 MB, giving the system the ability to manage a maximum of 28GB worth
# of swapped out data.
#
options 	VM_SWZONE_SIZE_MAX="(50*1024*1024)"

#
# Enable extra debugging code for locks.  This stores the filename and
# line of whatever acquired the lock in the lock itself, and change a
# number of function calls to pass around the relevant data.  This is
# not at all useful unless you are debugging lock code.  Also note
# that it is likely to break e.g. fstat(1) unless you recompile your
# userland with -DDEBUG_LOCKS as well.
#
# DEBUG_LOCKS_LATENCY adds a sysctl to add a forced latency loop
# (count to N) in front of any spinlock or gettoken.
#
options 	DEBUG_LOCKS
options		DEBUG_LOCKS_LATENCY

# Set the amount of time (in seconds) the system will wait before
# rebooting automatically when a kernel panic occurs.  If set to (-1),
# the system will wait indefinitely until a key is pressed on the
# console.
options 	PANIC_REBOOT_WAIT_TIME=16

# Specify a lower limit for the number of swap I/O buffers.
#
#options		NSWBUF_MIN=120

# The 'asr' driver provides support for current DPT/Adaptec SCSI RAID
# controllers (SmartRAID V and VI and later).
# These controllers require the CAM infrastructure.
#
device		asr

# The 'dpt' driver provides support for DPT controllers (http://www.dpt.com/).
# These have hardware RAID-{0,1,5} support, and do multi-initiator I/O.
# The DPT controllers are commonly re-licensed under other brand-names -
# some controllers by Olivetti, Dec, HP, AT&T, SNI, AST, Alphatronic, NEC and
# Compaq are actually DPT controllers.
#
# See src/sys/dev/raid/dpt for debugging and other subtle options.
#   DPT_MEASURE_PERFORMANCE Enables a set of (semi)invasive metrics. Various
#                           instruments are enabled.  The tools in
#                           /usr/sbin/dpt_* assume these to be enabled.
#   DPT_HANDLE_TIMEOUTS     Normally device timeouts are handled by the DPT.
#                           If you ant the driver to handle timeouts, enable
#                           this option.  If your system is very busy, this
#                           option will create more trouble than solve.
#   DPT_TIMEOUT_FACTOR      Used to compute the excessive amount of time to
#                           wait when timing out with the above option.
#  DPT_DEBUG_xxxx           These are controllable from sys/dev/raid/dpt/dpt.h
#  DPT_LOST_IRQ             When enabled, will try, once per second, to catch
#                           any interrupt that got lost.  Seems to help in some
#                           DPT-firmware/Motherboard combinations.  Minimal
#                           cost, great benefit.
#  DPT_RESET_HBA            Make "reset" actually reset the controller
#                           instead of fudging it.  Only enable this if you
#			    are 100% certain you need it.

device		dpt

# DPT options
#!CAM# options 	DPT_MEASURE_PERFORMANCE
#!CAM# options 	DPT_HANDLE_TIMEOUTS
options 	DPT_TIMEOUT_FACTOR=4
options 	DPT_LOST_IRQ
options 	DPT_RESET_HBA

#
# Compaq "CISS" RAID controllers (SmartRAID 5* series)
# These controllers have a SCSI-like interface, and require the
# CAM infrastructure.
#
device		ciss

#
# Intel Integrated RAID controllers.
# This driver is supported and maintained by
# "Leubner, Achim" <Achim_Leubner@adaptec.com>.
#
device          iir

#
# Mylex AcceleRAID and eXtremeRAID controllers with v6 and later
# firmware.  These controllers have a SCSI-like interface, and require
# the CAM infrastructure.
#
device          mly

# USB support
#

# UHCI controller
device		uhci
# OHCI controller
device		ohci
# EHCI controller
device		ehci
# XHCI controller
device		xhci
# General USB code (mandatory for USB)
device		usb
# Human Interface Device (anything with buttons and dials)
device		uhid
# USB keyboard
device		ukbd
# USB printer
device		ulpt
# USB mass storage (Requires scbus and da)
device		umass
# USB mass storage driver for device-side mode
device		usfs
# USB modem support
device		umodem
# USB mouse
device		ums
# eGalax USB touch screen
device		uep
# Diamond Rio 500 MP3 player
device		urio
# USB com devices
device		"u3g"
device		uark
device		ubsa
device		ubser
device		uchcom
device		ucom
device		ucycom
device		ufoma
device		uftdi
device		ugensa
device		uipaq
device		umcs
device		umct
device		umoscom
device		uplcom
device		uslcom
device		uvisor
device		uvscom

#
# USB ethernet support
device		uether
#
# ADMtek USB ethernet. Supports the LinkSys USB100TX,
# the Billionton USB100, the Melco LU-ATX, the D-Link DSB-650TX
# and the SMC 2202USB. Also works with the ADMtek AN986 Pegasus
# eval board.
device		aue
#
# ASIX Electronics AX88172 USB 2.0 ethernet driver. Used in the
# LinkSys USB200M and various other adapters.
device		axe
#
# ASIX Electronics AX88178A/AX88179 USB 2.0/3.0 gigabit ethernet driver.
device		axge
#
# CATC USB-EL1201A USB ethernet. Supports the CATC Netmate
# and Netmate II, and the Belkin F5U111.
device		cue
#
# USB Apple iPhone/iPad tethered Ethernet driver
device		ipheth
#
# Kawasaki LSI ethernet. Supports the LinkSys USB10T,
# Entrega USB-NET-E45, Peracom Ethernet Adapter, the
# 3Com 3c19250, the ADS Technologies USB-10BT, the ATen UC10T,
# the Netgear EA101, the D-Link DSB-650, the SMC 2102USB
# and 2104USB, and the Corega USB-T.
device		kue
#
# Moschip MCS7730/MCS7840 USB to fast ethernet. Supports the Sitecom LN030.
device		mos
#
# Davicom DM9601E USB to fast ethernet. Supports the Corega FEther USB-TXC.
device		udav

# USB wireless NICs, requires wlan_amrr
#
# Ralink Technology RT2501USB/RT2601USB
device		rum
#
# Ralink Technology RT2700U/RT2800U/RT3000U wireless driver
device		run
device		runfw
#
# RNDIS USB ethernet driver
device		urndis
#
# Realtek RTL8188CU/RTL8192CU wireless driver
device		urtwn
device		urtwnfw
options		URTWN_WITHOUT_UCODE

# Fm Radio
#
device		ufm

# Templates for programming USB device side drivers
#
device		usb_template

# debugging options for the USB subsystem
#
options 	USB_DEBUG

# options for ukbd:
options 	UKBD_DFLT_KEYMAP	# specify the built-in keymap
makeoptions	UKBD_DFLT_KEYMAP=it.iso

# Firewire support
device		firewire	# Firewire bus code
device		sbp		# SCSI over Firewire (Requires scbus and da)
device		fwe		# Ethernet over Firewire (non-standard!)

# dcons support (Dumb Console Device)
device		dcons			# dumb console driver
device		dcons_crom		# FireWire attachment
options		DCONS_BUF_SIZE=16384	# buffer size
options		DCONS_POLL_HZ=100	# polling rate
options		DCONS_FORCE_CONSOLE=1	# force to be the primary console
options		DCONS_FORCE_GDB=1	# force to be the gdb device

#####################################################################
# crypto subsystem
#
# This is a port of the openbsd crypto framework.  Include this when
# configuring IPsec and when you have a h/w crypto device to accelerate
# user applications that link to openssl.
#
# Drivers are ports from openbsd with some simple enhancements that have
# been fed back to openbsd (and hopefully will be included).

device		crypto		# core crypto support
device		cryptodev	# /dev/crypto for access to h/w

device		rndtest		# FIPS 140-2 entropy tester

device		hifn		# Hifn 7951, 7781, etc.
options		HIFN_DEBUG	# enable debugging support: hw.hifn.debug
#options	HIFN_NO_RNG	# for devices without RNG
options		HIFN_RNDTEST	# enable rndtest support

device		safe		# SafeNet 1141
options 	SAFE_DEBUG	# enable debugging support: hw.safe.debug
#options	SAFE_NO_RNG	# for devices without RNG
options 	SAFE_RNDTEST	# enable rndtest support

device		ubsec		# Broadcom 5501, 5601, 58xx
options		UBSEC_DEBUG	# enable debugging support: hw.ubsec.debug
#options	UBSEC_NO_RNG	# for devices without RNG
options		UBSEC_RNDTEST	# enable rndtest support

device		aesni		# hardware crypto/RNG for AES-NI
device		padlock		# hardware crypto/RNG for VIA C3/C7/Eden
device		rdrand		# hardware RNG for RdRand

#
# ACPI support using the Intel ACPI Component Architecture reference
# implementation.
#
# ACPI_DEBUG enables the use of the debug.acpi.level and debug.acpi.layer
# kernel environment variables to select initial debugging levels for the
# Intel ACPICA code.
#
# Note that building ACPI into the kernel is deprecated; the module is
# normally loaded automatically by the loader.

device		acpi
options 	ACPI_DEBUG

# ACPI WMI Mapping driver
device		acpi_wmi

# ACPI Asus Extras (LCD backlight/brightness, video output, etc.)
device		acpi_asus

# ACPI Fujitsu Extras (Buttons)
device		acpi_fujitsu

# ACPI extras driver for HP laptops
device		acpi_hp

# ACPI Panasonic Extras (LCD backlight/brightness, video output, etc.)
device		acpi_panasonic

# ACPI pvpanic driver for virtual machines running in Qemu
device		acpi_pvpanic

# ACPI Sony extra (LCD brightness)
device		acpi_sony

# ACPI extras driver for ThinkPad laptops
device		acpi_thinkpad

# ACPI Toshiba Extras (LCD backlight/brightness, video output, etc.)
device		acpi_toshiba

# ACPI Video Extensions (LCD backlight/brightness, video output, etc.)
device		acpi_video

# ACPI Docking Station
device		acpi_dock

device		aibs		# ASUSTeK AI Booster (ACPI ASOC ATK0110)

# DRM options:
# drm:		General DRM code
# i915:		Intel integrated GPUs, starting from the 830M family
# radeon:	ATI/AMD Radeon cards
#
# DRM_DEBUG:	include debug printfs, very slow
#
# DRM requires AGP in the kernel.
#
# Also you'll need to have the following 3 lines in the kernel config.
#	device acpi
#	device iicbus
#	device iicbb

device		drm

# For testing and debugging.
device		"i915"
device		radeon

options 	DRM_DEBUG
options		VGA_SWITCHEROO

#
# Misc devices
#
device		cmx		# Omnikey CardMan 4040 smartcard reader
device		amdsbwd		# AMD South Bridge watchdog
device		gpio		# Enable support for the gpio framework
device		ichwd		# Intel ICH watchdog interrupt timer
device		tbridge		# regression testing

#
# Hyper-V support
#
device		vmbus

#
# Virtio support
#
device		virtio
device		virtio_blk
device		virtio_scsi
device		vtnet
device		virtio_pci

# VMware support
#
device		vmx		# VMware VMXNET3 Ethernet

#
# Gpio support for ACPI based SoC platforms
#
device		gpio_acpi
device		gpio_intel	# GPIO support for Intel SoCs

#
# Embedded system options:
#
# An embedded system might want to run something other than init.
options 	INIT_PATH="/sbin/init:/sbin/oinit"

# Debug options
options 	BUS_DEBUG       # enable newbus debugging
options		RSS_DEBUG	# enable RSS (Receive Side Scaling) debugging

# Record the program counter of the code interrupted by the statistics
# clock interrupt.  Use pctrack(8) to dump this information.
options		DEBUG_PCTRACK

# evdev interface
device		evdev		# input event device support
options		EVDEV_SUPPORT	# evdev support in legacy drivers
options		EVDEV_DEBUG	# enable event debug messages

# More undocumented options for linting.
# Note that documenting these are not considered an affront.

#options	ACPI_NO_SEMAPHORES
#options 	BKTR_ALLOC_PAGES=xxx
options 	CAM_DEBUG_DELAY
options 	CLUSTERDEBUG
options 	DEBUG
options 	DEBUG_CRIT_SECTIONS
options		BCE_RSS_DEBUG
options		BCE_TSS_DEBUG
options		BNX_RSS_DEBUG
options		BNX_TSO_DEBUG
options		BNX_TSS_DEBUG
options		EMX_RSS_DEBUG
options		EMX_TSO_DEBUG
options		EMX_TSS_DEBUG
options		JME_RSS_DEBUG
options		IGB_RSS_DEBUG
options		IGB_TSS_DEBUG
options		IGB_MSIX_DEBUG
options		IX_RSS_DEBUG
options 	ENABLE_ALART
options 	FB_DEBUG=2
options 	FB_INSTALL_CDEV
#options	IEEE80211_DEBUG_REFCNT
options		IEEE80211_SUPPORT_SUPERG
options 	KBDIO_DEBUG=10
options 	KBD_MAXRETRY=4
options 	KBD_MAXWAIT=6
options 	KBD_RESETDELAY=201
#options 	KERN_TIMESTAMP
options 	KEY
options 	LOCKF_DEBUG
#options	MAXFILES=xxx
options		MBUF_DEBUG
options		NO_LWKT_SPLIT_USERPRI
options 	PANIC_DEBUG
options 	PMAP_DEBUG
options 	PSM_DEBUG=4
options 	SCSI_NCR_DEBUG
options 	SCSI_NCR_MAX_SYNC=10000
options 	SCSI_NCR_MAX_WIDE=1
options 	SCSI_NCR_MYADDR=7
options 	SI_DEBUG
options		SLAB_DEBUG
options 	SOCKBUF_DEBUG
options		TDMA_BINTVAL_DEFAULT=5
options		TDMA_SLOTCNT_DEFAULT=2
options		TDMA_SLOTLEN_DEFAULT=10*1000
options		TDMA_TXRATE_11A_DEFAULT=2*24
options		TDMA_TXRATE_11B_DEFAULT=2*11
options		TDMA_TXRATE_11G_DEFAULT=2*24
options		TDMA_TXRATE_11NA_DEFAULT="(4|IEEE80211_RATE_MCS)"
options		TDMA_TXRATE_11NG_DEFAULT="(4|IEEE80211_RATE_MCS)"
options		TDMA_TXRATE_HALF_DEFAULT=2*12
options		TDMA_TXRATE_QUARTER_DEFAULT=2*6
options		TDMA_TXRATE_TURBO_DEFAULT=2*24
#options 	TIMER_FREQ="((14318182+6)/12)"
options 	VFS_BIO_DEBUG
options		VM_PAGE_DEBUG
options 	XBONEHACK

options	KTR
options KTR_ALL
options	KTR_ENTRIES=1024
options	KTR_VERBOSE=1
#options KTR_ACPI_EC
#options KTR_CTXSW
#options KTR_DMCRYPT
#options KTR_ETHERNET
#options KTR_HAMMER
#options KTR_IFQ
#options KTR_IF_BGE
#options KTR_IF_EM
#options KTR_IF_EMX
#options KTR_IF_POLL
#options KTR_IF_START
#options KTR_IPIQ
#options KTR_KERNENTRY
#options KTR_MEMORY
#options KTR_SERIALIZER
#options KTR_SOWAKEUP
#options KTR_SPIN_CONTENTION
#options KTR_TESTLOG
#options KTR_TOKENS
#options KTR_TSLEEP
#options KTR_UDP
#options KTR_USCHED_BSD4
#options KTR_USCHED_DFLY

# ALTQ
options 	ALTQ		#alternate queueing
options 	ALTQ_CBQ	#class based queueing
options 	ALTQ_RED	#random early detection
options 	ALTQ_RIO	#triple red for diffserv (needs RED)
options 	ALTQ_HFSC	#hierarchical fair service curve
options 	ALTQ_PRIQ	#priority queue
options 	ALTQ_FAIRQ	#fair queue
#options 	ALTQ_NOPCC	#don't use processor cycle counter
options 	ALTQ_DEBUG	#for debugging
# you might want to set kernel timer to 1kHz if you use CBQ,
# especially with 100baseT
#options 	HZ=1000

# WATCHDOG
options		WDOG_DISABLE_ON_PANIC	# Automatically disable watchdogs on panic

# LED
options		ERROR_LED_ON_PANIC	# If an error led is present, light it up on panic