Remove ISDN support. Tools, kernel code, manpages, examples, everything.
[dragonfly.git] / sys / config / LINT
1 #
2 # LINT -- config file for checking all the sources, tries to pull in
3 #       as much of the source tree as it can.
4 #
5 # $FreeBSD: src/sys/i386/conf/LINT,v 1.749.2.144 2003/06/04 17:56:59 sam Exp $
6 #
7 # See the kernconf(5) manual page for more information on the format of
8 # this file.
9 #
10 # NB: You probably don't want to try running a kernel built from this
11 # file.  Instead, you should start from GENERIC, and add options from
12 # this file as required.
13 #
14
15 # These directives are mandatory.  The machine directive specifies the
16 # platform and the machine_arch directive specifies the cpu architecture.
17 #
18 platform        pc32
19 machine         i386
20 machine_arch    i386
21
22 #
23 # This is the ``identification'' of the kernel.  Usually this should
24 # be the same as the name of your kernel.
25 #
26 ident           LINT
27
28 #
29 # The `maxusers' parameter controls the static sizing of a number of
30 # internal system tables by a formula defined in subr_param.c.  Setting
31 # maxusers to 0 will cause the system to auto-size based on physical
32 # memory.
33 #
34 maxusers        10
35
36 #
37 # The `makeoptions' parameter allows variables to be passed to the
38 # generated Makefile in the build area.
39 #
40 # CONF_CFLAGS gives some extra compiler flags that are added to ${CFLAGS}
41 # after most other flags.  Here we use it to inhibit use of non-optimal
42 # gcc builtin functions (e.g., memcmp).
43 #
44 # DEBUG happens to be magic.
45 # The following is equivalent to 'config -g KERNELNAME' and creates
46 # 'kernel.debug' compiled with -g debugging as well as a normal
47 # 'kernel'.  Use 'make install.debug' to install the debug kernel
48 # but that isn't normally necessary as the debug symbols are not loaded
49 # by the kernel and are not useful there anyway.
50 #
51 # KERNEL can be overridden so that you can change the default name of your
52 # kernel.
53 #
54 # MODULES_OVERRIDE can be used to limit modules built to a specific list.
55 #
56 # INSTALLSTRIPPED can be set to cause installkernel to install stripped
57 # kernels and modules rather than a kernel and modules with debug symbols.
58 #
59 # INSTALLSTRIPPEDMODULES can be set to allow a full debug kernel to be
60 # installed, but to strip the installed modules.
61 #
62 makeoptions     CONF_CFLAGS=-fno-builtin  #Don't allow use of memcmp, etc.
63 #makeoptions    DEBUG=-g                #Build kernel with gdb(1) debug symbols
64 #makeoptions    KERNEL=foo              #Build kernel "foo" and install "/foo"
65 # Only build Linux API modules and plus those parts of the sound system I need.
66 #makeoptions    MODULES_OVERRIDE="linux sound/snd sound/pcm sound/driver/maestro3"
67 #makeoptions    INSTALLSTRIPPED=1
68 #makeoptions    INSTALLSTRIPPEDMODULES=1
69
70 #
71 # Certain applications can grow to be larger than the 128M limit
72 # that DragonFly initially imposes.  Below are some options to
73 # allow that limit to grow to 256MB, and can be increased further
74 # with changing the parameters.  MAXDSIZ is the maximum that the
75 # limit can be set to, and the DFLDSIZ is the default value for
76 # the limit.  MAXSSIZ is the maximum that the stack limit can be
77 # set to.  You might want to set the default lower than the max,
78 # and explicitly set the maximum with a shell command for processes
79 # that regularly exceed the limit like INND.
80 #
81 options         MAXDSIZ="(256*1024*1024)"
82 options         MAXSSIZ="(256*1024*1024)"
83 options         DFLDSIZ="(256*1024*1024)"
84
85 #
86 # BLKDEV_IOSIZE sets the default block size used in user block
87 # device I/O.  Note that this value will be overridden by the label
88 # when specifying a block device from a label with a non-0
89 # partition blocksize.  The default is PAGE_SIZE.
90 #
91 options         BLKDEV_IOSIZE=8192
92
93 # This allows you to actually store this configuration file into
94 # the kernel binary itself, where it may be later read by saying:
95 #    strings -n 3 /kernel | sed -n 's/^___//p' > MYKERNEL
96 #
97 options         INCLUDE_CONFIG_FILE     # Include this file in kernel
98
99 #
100 # The root device and filesystem type can be compiled in;
101 # this provides a fallback option if the root device cannot
102 # be correctly guessed by the bootstrap code, or an override if
103 # the RB_DFLTROOT flag (-r) is specified when booting the kernel.
104 #
105 options         ROOTDEVNAME=\"ufs:da0s2e\"
106
107 #####################################################################
108 # SMP OPTIONS:
109 #
110 # SMP enables building of a Symmetric MultiProcessor Kernel. It will
111 # boot on both SMP and UP boxes.
112 #
113 # Notes:
114 #
115 #  An SMP kernel will ONLY run on an Intel MP spec. qualified motherboard.
116 #
117 #  Be sure to disable 'cpu I486_CPU' for SMP kernels.
118 #
119 #  Check the 'Rogue SMP hardware' section to see if additional options
120 #   are required by your hardware.
121 #
122 #options        SMP                     # Symmetric MultiProcessor Kernel
123
124 #####################################################################
125 # CPU OPTIONS
126
127 #
128 # You must specify at least one CPU (the one you intend to run on);
129 # deleting the specification for CPUs you don't need to use may make
130 # parts of the system run faster.
131 #
132 cpu             I486_CPU
133 cpu             I586_CPU                # aka Pentium(tm)
134 cpu             I686_CPU                # aka Pentium Pro(tm)
135
136 #
137 # Options for CPU features.
138 #
139 # CPU_ATHLON_SSE_HACK tries to enable SSE instructions when the BIOS has
140 # forgotten to enable them.
141 #
142 # CPU_BLUELIGHTNING_FPU_OP_CACHE enables FPU operand cache on IBM
143 # BlueLightning CPU.  It works only with Cyrix FPU, and this option
144 # should not be used with Intel FPU.
145 #
146 # CPU_BLUELIGHTNING_3X enables triple-clock mode on IBM Blue Lightning
147 # CPU if CPU supports it. The default is double-clock mode on
148 # BlueLightning CPU box.
149 #
150 # CPU_BTB_EN enables branch target buffer on Cyrix 5x86 (NOTE 1).
151 #
152 # CPU_DIRECT_MAPPED_CACHE sets L1 cache of Cyrix 486DLC CPU in direct
153 # mapped mode.  Default is 2-way set associative mode.
154 #
155 # CPU_CYRIX_NO_LOCK enables weak locking for the entire address space
156 # of Cyrix 6x86 and 6x86MX CPUs by setting the NO_LOCK bit of CCR1.
157 # Otherwise, the NO_LOCK bit of CCR1 is cleared.  (NOTE 3)
158 #
159 # CPU_DISABLE_5X86_LSSER disables load store serialize (i.e. enables
160 # reorder).  This option should not be used if you use memory mapped
161 # I/O device(s).
162 #
163 # CPU_DISABLE_SSE disables SSE/MMX2 instructions support.
164 #
165 # CPU_ENABLE_EST enables support for Enhanced SpeedStep technology
166 # found in Pentium(tm) M processors.
167 #
168 # CPU_ENABLE_LONGRUN enables support for Transmeta Crusoe LongRun
169 # technology which allows to restrict power consumption of the CPU by
170 # using group of hw.crusoe.* sysctls.
171 #
172 # CPU_ENABLE_TCC enables Thermal Control Circuitry (TCC) found in some
173 # Pentium(tm) 4 and (possibly) later CPUs.  When enabled and detected,
174 # TCC supports restricting power consumption using the hw.p4tcc.*
175 # sysctls.  This operates independently of SpeedStep and is useful on
176 # systems where other mechanisms such as apm(4) or acpi(4) don't work.
177 #
178 # CPU_FASTER_5X86_FPU enables faster FPU exception handler.
179 #
180 # CPU_I486_ON_386 enables CPU cache on i486 based CPU upgrade products
181 # for i386 machines.
182 #
183 # CPU_IORT defines I/O clock delay time (NOTE 1).  Default values of
184 # I/O clock delay time on Cyrix 5x86 and 6x86 are 0 and 7,respectively
185 # (no clock delay).
186 #
187 # CPU_L2_LATENCY specified the L2 cache latency value.  This option is used
188 # only when CPU_PPRO2CELERON is defined and Mendocino Celeron is detected.
189 # The default value is 5.
190 #
191 # CPU_ELAN enables support for AMDs ElanSC520 CPU.
192 #
193 # CPU_GEODE enables support for AMD Geode LX, Geode SC1100 and AMD CS5536
194 #
195 # CPU_LOOP_EN prevents flushing the prefetch buffer if the destination
196 # of a jump is already present in the prefetch buffer on Cyrix 5x86(NOTE
197 # 1).
198 #
199 # CPU_PPRO2CELERON enables L2 cache of Mendocino Celeron CPUs.  This option
200 # is useful when you use Socket 8 to Socket 370 converter, because most Pentium
201 # Pro BIOSs do not enable L2 cache of Mendocino Celeron CPUs.
202 #
203 # CPU_RSTK_EN enables return stack on Cyrix 5x86 (NOTE 1).
204 #
205 # CPU_SUSP_HLT enables suspend on HALT.  If this option is set, CPU
206 # enters suspend mode following execution of HALT instruction.
207 #
208 # CPU_WT_ALLOC enables write allocation on Cyrix 6x86/6x86MX and AMD
209 # K5/K6/K6-2 cpus.
210 #
211 # CYRIX_CACHE_WORKS enables CPU cache on Cyrix 486 CPUs with cache
212 # flush at hold state.
213 #
214 # CYRIX_CACHE_REALLY_WORKS enables (1) CPU cache on Cyrix 486 CPUs
215 # without cache flush at hold state, and (2) write-back CPU cache on
216 # Cyrix 6x86 whose revision < 2.7 (NOTE 2).
217 #
218 # NO_F00F_HACK disables the hack that prevents Pentiums (and ONLY
219 # Pentiums) from locking up when a LOCK CMPXCHG8B instruction is
220 # executed.  This option is only needed if I586_CPU is also defined,
221 # and should be included for any non-Pentium CPU that defines it.
222 #
223 # NO_MEMORY_HOLE is an optimisation for systems with AMD K6 processors
224 # which indicates that the 15-16MB range is *definitely* not being
225 # occupied by an ISA memory hole.
226 #
227 # NOTE 1: The CPU_BTB_EN, CPU_IORT, CPU_LOOP_EN and CPU_RSTK_EN options
228 # should not be used because of CPU bugs. They may crash your system.
229 #
230 # NOTE 2: If CYRIX_CACHE_REALLY_WORKS is not set, CPU cache is enabled
231 # in write-through mode when revision < 2.7.  If revision of Cyrix
232 # 6x86 >= 2.7, CPU cache is always enabled in write-back mode.
233 #
234 # NOTE 3: This option may cause failures for software that requires
235 # locked cycles in order to operate correctly.
236 #
237 options         CPU_ATHLON_SSE_HACK
238 options         CPU_BLUELIGHTNING_FPU_OP_CACHE
239 options         CPU_BLUELIGHTNING_3X
240 options         CPU_BTB_EN
241 options         CPU_CYRIX_NO_LOCK
242 options         CPU_DIRECT_MAPPED_CACHE
243 options         CPU_DISABLE_5X86_LSSER
244 options         CPU_DISABLE_SSE
245 options         CPU_ELAN
246 options         CPU_ENABLE_EST
247 options         CPU_ENABLE_LONGRUN
248 options         CPU_ENABLE_TCC
249 options         CPU_FASTER_5X86_FPU
250 options         CPU_GEODE
251 options         CPU_I486_ON_386
252 options         CPU_IORT
253 options         CPU_L2_LATENCY=5
254 options         CPU_LOOP_EN
255 options         CPU_PPRO2CELERON
256 options         CPU_RSTK_EN
257 options         CPU_SUSP_HLT
258 options         CPU_WT_ALLOC
259 options         CYRIX_CACHE_WORKS
260 options         CYRIX_CACHE_REALLY_WORKS
261 #options        NO_F00F_HACK
262 options         NO_MEMORY_HOLE
263
264 #
265 # A math emulator is mandatory if you wish to run on hardware which
266 # does not have a floating-point processor.
267 options         MATH_EMULATE            #Support for x87 emulation
268
269 #####################################################################
270 # COMPATIBILITY OPTIONS
271
272 #
273 # Implement system calls compatible with 4.3BSD and older versions of
274 # FreeBSD.  You probably do NOT want to remove this as much current code
275 # still relies on the 4.3 emulation.
276 #
277 options         COMPAT_43
278
279 #
280 # Implement system calls compatible with DragonFly 1.2 and older.
281 #
282 options         COMPAT_DF12             #Compatible with DragonFly 1.2 and earlier
283
284 # Enable NDIS binary driver support
285 options         NDISAPI
286 device          ndis
287
288 #
289 # These three options provide support for System V Interface
290 # Definition-style interprocess communication, in the form of shared
291 # memory, semaphores, and message queues, respectively.
292 #
293 # System V shared memory and tunable parameters
294 options         SYSVSHM         # include support for shared memory
295 options         SHMMAXPGS=1025  # max amount of shared memory pages (4k on i386)
296 options         SHMALL=1025     # max amount of shared memory (bytes)
297 options         SHMMAX="(SHMMAXPGS*PAGE_SIZE+1)"
298                                 # max shared memory segment size (bytes)
299 options         SHMMIN=2        # min shared memory segment size (bytes)
300 options         SHMMNI=33       # max number of shared memory identifiers
301 options         SHMSEG=9        # max shared memory segments per process
302
303 # System V semaphores and tunable parameters
304 options         SYSVSEM         # include support for semaphores
305 options         SEMMAP=31       # amount of entries in semaphore map
306 options         SEMMNI=11       # number of semaphore identifiers in the system
307 options         SEMMNS=61       # number of semaphores in the system
308 options         SEMMNU=31       # number of undo structures in the system
309 options         SEMMSL=61       # max number of semaphores per id
310 options         SEMOPM=101      # max number of operations per semop call
311 options         SEMUME=11       # max number of undo entries per process
312
313 # System V message queues and tunable parameters
314 options         SYSVMSG         # include support for message queues
315 options         MSGMNB=2049     # max characters per message queue
316 options         MSGMNI=41       # max number of message queue identifiers
317 options         MSGSEG=2049     # max number of message segments in the system
318 options         MSGSSZ=16       # size of a message segment MUST be power of 2
319 options         MSGTQL=41       # max amount of messages in the system
320
321 #####################################################################
322 # DEBUGGING OPTIONS
323
324 #
325 # Enable the kernel debugger.
326 #
327 options         DDB
328
329 #
330 # Print a stack trace on kernel panic.
331 #
332 options         DDB_TRACE
333
334 #
335 # Don't drop into DDB for a panic. Intended for unattended operation
336 # where you may want to drop to DDB from the console, but still want
337 # the machine to recover from a panic
338 #
339 options         DDB_UNATTENDED
340
341 #
342 # If using GDB remote mode to debug the kernel, there's a non-standard
343 # extension to the remote protocol that can be used to use the serial
344 # port as both the debugging port and the system console.  It's non-
345 # standard and you're on your own if you enable it.  See also the
346 # "remotechat" variables in the DragonFly specific version of gdb.
347 #
348 options         GDB_REMOTE_CHAT
349
350 #
351 # KTRACE enables the system-call tracing facility ktrace(2).
352 #
353 options         KTRACE                  #kernel tracing
354
355 #
356 # The INVARIANTS option is used in a number of source files to enable
357 # extra sanity checking of internal structures.  This support is not
358 # enabled by default because of the extra time it would take to check
359 # for these conditions, which can only occur as a result of
360 # programming errors.
361 #
362 options         INVARIANTS
363
364 #
365 # The DIAGNOSTIC option is used to enable extra debugging information
366 # from some parts of the kernel.  As this makes everything more noisy,
367 # it is disabled by default.
368 #
369 options         DIAGNOSTIC
370
371 #
372 # PERFMON causes the driver for Pentium/Pentium Pro performance counters
373 # to be compiled.  See perfmon(4) for more information.
374 #
375 options         PERFMON
376
377
378 #
379 # This option let some drivers co-exist that can't co-exist in a running
380 # system.  This is used to be able to compile all kernel code in one go for
381 # quality assurance purposes (like this file, which the option takes it name
382 # from.)
383 #
384 options         COMPILING_LINT
385
386
387 # XXX - this doesn't belong here.
388 # Allow ordinary users to take the console - this is useful for X.
389 options         UCONSOLE
390
391 # XXX - this doesn't belong here either
392 options         USERCONFIG              #boot -c editor
393 options         INTRO_USERCONFIG        #imply -c and show intro screen
394 options         VISUAL_USERCONFIG       #visual boot -c editor
395
396 #####################################################################
397 # NETWORKING OPTIONS
398
399 #
400 # Protocol families:
401 #  Only the INET (Internet) family is officially supported in DragonFly.
402 #  Source code for the NS (Xerox Network Service) is provided for amusement
403 #  value.
404 #
405 options         INET                    #Internet communications protocols
406 options         INET6                   #IPv6 communications protocols
407 options         IPSEC                   #IP security
408 options         IPSEC_ESP               #IP security (crypto; define w/ IPSEC)
409 options         IPSEC_DEBUG             #debug for IP security
410 #
411 # Set IPSEC_FILTERGIF to force packets coming through a gif tunnel
412 # to be processed by any configured packet filtering (ipfw).
413 # The default is that packets coming from a tunnel are _not_ processed;
414 # they are assumed trusted.
415 #
416 # Note that enabling this can be problematic as there are no mechanisms
417 # in place for distinguishing packets coming out of a tunnel (e.g. no
418 # encX devices as found on openbsd).
419 #
420 #options        IPSEC_FILTERGIF         #filter ipsec packets from a tunnel
421
422 #
423 # Experimental IPsec implementation that uses the kernel crypto
424 # framework.  This cannot be configured together with IPSEC and
425 # (currently) supports only IPv4.  To use this you must also
426 # configure the crypto device (see below).  Note that with this
427 # you get all the IPsec protocols (e.g. there is no FAST_IPSEC_ESP).
428 # IPSEC_DEBUG is used, as above, to configure debugging support
429 # within the IPsec protocols.
430 #
431 #options        FAST_IPSEC              #new IPsec
432
433 options         IPX                     #IPX/SPX communications protocols
434 options         IPXIP                   #IPX in IP encapsulation (not available)
435 options         IPTUNNEL                #IP in IPX encapsulation (not available)
436
437 options         NCP                     #NetWare Core protocol
438
439 options         MPLS                    #Multi-Protocol Label Switching
440
441 #
442 # SMB/CIFS requester
443 # NETSMB enables support for SMB protocol, it requires LIBMCHAIN and LIBICONV
444 # options.
445 # NETSMBCRYPTO enables support for encrypted passwords.
446 options         NETSMB                  #SMB/CIFS requester
447 options         NETSMBCRYPTO            #encrypted password support for SMB
448
449 # mchain library. It can be either loaded as KLD or compiled into kernel
450 options         LIBMCHAIN               #mbuf management library
451
452 # netgraph(4). Enable the base netgraph code with the NETGRAPH option.
453 # Individual node types can be enabled with the corresponding option
454 # listed below; however, this is not strictly necessary as netgraph
455 # will automatically load the corresponding KLD module if the node type
456 # is not already compiled into the kernel. Each type below has a
457 # corresponding man page, e.g., ng_async(4).
458 options         NETGRAPH                #netgraph(4) system
459 options         NETGRAPH_ASYNC
460 options         NETGRAPH_BPF
461 options         NETGRAPH_BRIDGE
462 options         NETGRAPH_CISCO
463 options         NETGRAPH_ECHO
464 options         NETGRAPH_EIFACE
465 options         NETGRAPH_ETHER
466 options         NETGRAPH_FRAME_RELAY
467 options         NETGRAPH_HOLE
468 options         NETGRAPH_IFACE
469 options         NETGRAPH_KSOCKET
470 options         NETGRAPH_L2TP
471 options         NETGRAPH_LMI
472 # MPPC compression requires proprietary files (not included)
473 #options        NETGRAPH_MPPC_COMPRESSION
474 options         NETGRAPH_MPPC_ENCRYPTION
475 options         NETGRAPH_ONE2MANY
476 options         NETGRAPH_PPP
477 options         NETGRAPH_PPPOE
478 options         NETGRAPH_PPTPGRE
479 options         NETGRAPH_RFC1490
480 options         NETGRAPH_SOCKET
481 options         NETGRAPH_TEE
482 options         NETGRAPH_TTY
483 options         NETGRAPH_UI
484 options         NETGRAPH_VJC
485
486 device          mn      # Munich32x/Falc54 Nx64kbit/sec cards.
487
488 #
489 # Network interfaces:
490 #  The `loop' pseudo-device is MANDATORY when networking is enabled.
491 #  The `ether' pseudo-device provides generic code to handle
492 #  Ethernets; it is MANDATORY when a Ethernet device driver is
493 #  configured.
494 #  The `sppp' pseudo-device serves a similar role for certain types
495 #  of synchronous PPP links (like `ar').
496 #  The `sl' pseudo-device implements the Serial Line IP (SLIP) service.
497 #  The `ppp' pseudo-device implements the Point-to-Point Protocol.
498 #  The `bpf' pseudo-device enables the Berkeley Packet Filter.  Be
499 #  aware of the legal and administrative consequences of enabling this
500 #  option.  The number of devices determines the maximum number of
501 #  simultaneous BPF clients programs runnable.
502 #  The `disc' pseudo-device implements a minimal network interface,
503 #  which throws away all packets sent and never receives any.  It is
504 #  included for testing purposes.  This shows up as the 'ds' interface.
505 #  The `tun' pseudo-device implements (user-)ppp and nos-tun
506 #  The `gif' pseudo-device implements IPv6 over IP4 tunneling,
507 #  IPv4 over IPv6 tunneling, IPv4 over IPv4 tunneling and
508 #  IPv6 over IPv6 tunneling.
509 #  The `gre' device implements two types of IP4 over IP4 tunneling:
510 #  GRE and MOBILE, as specified in the RFC1701 and RFC2004.
511 #  The `faith' pseudo-device captures packets sent to it and diverts them
512 #  to the IPv4/IPv6 translation daemon.
513 #  The `stf' device implements 6to4 encapsulation.
514 #  The `ef' pseudo-device provides support for multiple ethernet frame types
515 #  specified via ETHER_* options. See ef(4) for details.
516 #
517 # The PPP_BSDCOMP option enables support for compress(1) style entire
518 # packet compression, the PPP_DEFLATE is for zlib/gzip style compression.
519 # PPP_FILTER enables code for filtering the ppp data stream and selecting
520 # events for resetting the demand dial activity timer - requires bpf.
521 # See pppd(8) for more details.
522 #
523 pseudo-device   ether                   #Generic Ethernet
524 pseudo-device   vlan    1               #VLAN support
525 pseudo-device   bridge                  #Bridging support
526 pseudo-device   sppp                    #Generic Synchronous PPP
527 pseudo-device   loop                    #Network loopback device
528 pseudo-device   bpf                     #Berkeley packet filter
529 pseudo-device   disc                    #Discard device (ds0, ds1, etc)
530 pseudo-device   tun                     #Tunnel driver (ppp(8), nos-tun(8))
531 pseudo-device   sl      2               #Serial Line IP
532 pseudo-device   gre                     #IP over IP tunneling
533 pseudo-device   ppp     2               #Point-to-point protocol
534 options         PPP_BSDCOMP             #PPP BSD-compress support
535 options         PPP_DEFLATE             #PPP zlib/deflate/gzip support
536 options         PPP_FILTER              #enable bpf filtering (needs bpf)
537
538 pseudo-device   ef                      # Multiple ethernet frames support
539 options         ETHER_II                # enable Ethernet_II frame
540 options         ETHER_8023              # enable Ethernet_802.3 (Novell) frame
541 options         ETHER_8022              # enable Ethernet_802.2 frame
542 options         ETHER_SNAP              # enable Ethernet_802.2/SNAP frame
543
544 # for IPv6
545 pseudo-device   gif                     #IPv6 and IPv4 tunneling
546 pseudo-device   faith   1               #for IPv6 and IPv4 translation
547 pseudo-device   stf                     #6to4 IPv6 over IPv4 encapsulation
548
549 #
550 # Internet family options:
551 #
552 # MROUTING enables the kernel multicast packet forwarder, which works
553 # with mrouted(8).
554 #
555 # PIM enables Protocol Independent Multicast in the kernel.
556 # Requires MROUTING enabled.
557 #
558 # IPFIREWALL enables support for IP firewall construction, in
559 # conjunction with the `ipfw' program.  IPFIREWALL_VERBOSE sends
560 # logged packets to the system logger.  IPFIREWALL_VERBOSE_LIMIT
561 # limits the number of times a matching entry can be logged.
562 #
563 # WARNING:  IPFIREWALL defaults to a policy of "deny ip from any to any"
564 # and if you do not add other rules during startup to allow access,
565 # YOU WILL LOCK YOURSELF OUT.  It is suggested that you set firewall_type=open
566 # in /etc/rc.conf when first enabling this feature, then refining the
567 # firewall rules in /etc/rc.firewall after you've tested that the new kernel
568 # feature works properly.
569 #
570 # IPFIREWALL_DEFAULT_TO_ACCEPT causes the default rule (at boot) to
571 # allow everything.  Use with care, if a cracker can crash your
572 # firewall machine, they can get to your protected machines.  However,
573 # if you are using it as an as-needed filter for specific problems as
574 # they arise, then this may be for you.  Changing the default to 'allow'
575 # means that you won't get stuck if the kernel and /sbin/ipfw binary get
576 # out of sync.
577 #
578 # IPDIVERT enables the divert IP sockets, used by ``ipfw divert''
579 #
580 # IPSTEALTH enables code to support stealth forwarding (i.e., forwarding
581 # packets without touching the ttl).  This can be useful to hide firewalls
582 # from traceroute and similar tools.
583 #
584 # TCPDEBUG is undocumented.
585 #
586 options         MROUTING                # Multicast routing
587 options         PIM                     # Protocol Independent Multicast
588 options         IPFIREWALL              #firewall
589 options         IPFIREWALL_DEBUG        #debug prints
590 options         IPFIREWALL_VERBOSE      #enable logging to syslogd(8)
591 options         IPFIREWALL_FORWARD      #enable transparent proxy support
592 options         IPFIREWALL_VERBOSE_LIMIT=100    #limit verbosity
593 options         IPFIREWALL_DEFAULT_TO_ACCEPT    #allow everything by default
594 options         IPV6FIREWALL            #firewall for IPv6
595 options         IPV6FIREWALL_VERBOSE
596 options         IPV6FIREWALL_VERBOSE_LIMIT=100
597 options         IPV6FIREWALL_DEFAULT_TO_ACCEPT
598 options         IPDIVERT                #divert sockets
599 options         IPSTEALTH               #support for stealth forwarding
600 options         TCPDEBUG
601
602 device          pf
603 device          pflog
604
605 #CARP
606 pseudo-device carp
607 options CARP
608
609 # The MBUF_STRESS_TEST option enables options which create
610 # various random failures / extreme cases related to mbuf
611 # functions.  See the mbuf(9) manpage for a list of available
612 # test cases.
613 options         MBUF_STRESS_TEST
614
615 # Statically link in accept filters
616 options                ACCEPT_FILTER_DATA
617 options                ACCEPT_FILTER_HTTP
618
619 # TCP_SIGNATURE adds support for RFC 2385 (TCP-MD5) digests. These are
620 # carried in TCP option 19. This option is commonly used to protect
621 # TCP sessions (e.g. BGP) where IPSEC is not available nor desirable.
622 # This is enabled on a per-socket basis using the TCP_MD5SIG socket option.
623 # This requires the use of 'device crypto', 'options IPSEC'
624 # or 'device cryptodev'.
625 options   TCP_SIGNATURE   #include support for RFC 2385
626
627 #
628 # TCP_DROP_SYNFIN adds support for ignoring TCP packets with SYN+FIN. This
629 # prevents nmap et al. from identifying the TCP/IP stack, but breaks support
630 # for RFC1644 extensions and is not recommended for web servers.
631 #
632 options         TCP_DROP_SYNFIN         #drop TCP packets with SYN+FIN
633
634 # ICMP_BANDLIM enables icmp error response bandwidth limiting.   You
635 # typically want this option as it will help protect the machine from
636 # D.O.S. packet attacks.
637 #
638 options         ICMP_BANDLIM
639
640 # DUMMYNET enables the "dummynet" bandwidth limiter. You need
641 # IPFIREWALL as well. See the dummynet(4) and ipfw(8) manpages for more info.
642 #
643 options         DUMMYNET
644 options         DUMMYNET_DEBUG
645
646 #
647 # ATM (HARP version) options
648 #
649 # ATM_CORE includes the base ATM functionality code.  This must be included
650 #       for ATM support.
651 #
652 # ATM_IP includes support for running IP over ATM.
653 #
654 # At least one (and usually only one) of the following signalling managers
655 # must be included (note that all signalling managers include PVC support):
656 # ATM_SIGPVC includes support for the PVC-only signalling manager `sigpvc'.
657 # ATM_SPANS includes support for the `spans' signalling manager, which runs
658 #       the FORE Systems's proprietary SPANS signalling protocol.
659 # ATM_UNI includes support for the `uni30' and `uni31' signalling managers,
660 #       which run the ATM Forum UNI 3.x signalling protocols.
661 #
662 # The `hea' driver provides support for the Efficient Networks, Inc.
663 # ENI-155p ATM PCI Adapter.
664 #
665 # The `hfa' driver provides support for the FORE Systems, Inc.
666 # PCA-200E ATM PCI Adapter.
667 #
668 options         ATM_CORE                #core ATM protocol family
669 options         ATM_IP                  #IP over ATM support
670 options         ATM_SIGPVC              #SIGPVC signalling manager
671 options         ATM_SPANS               #SPANS signalling manager
672 options         ATM_UNI                 #UNI signalling manager
673 device          hea                     #Efficient ENI-155p ATM PCI
674 device          hfa                     #FORE PCA-200E ATM PCI
675
676 # DEVICE_POLLING adds support for mixed interrupt-polling handling
677 # of network device drivers, which has significant benefits in terms
678 # of robustness to overloads and responsivity, as well as permitting
679 # accurate scheduling of the CPU time between kernel network processing
680 # and other activities. The drawback is a moderate (up to 1/pollhz seconds)
681 # potential increase in response times. See polling(4) for further details.
682 #
683 options         DEVICE_POLLING
684
685 # IFPOLL_ENABLE adds hardware queues' based polling
686 options         IFPOLL_ENABLE
687
688 #####################################################################
689 # FILESYSTEM OPTIONS
690
691 #
692 # Only the root, /usr, and /tmp filesystems need be statically
693 # compiled; everything else will be automatically loaded at mount
694 # time.  (Exception: the UFS family --- FFS, and MFS ---
695 # cannot currently be demand-loaded.)  Some people still prefer
696 # to statically compile other filesystems as well.
697 #
698 # NB: The PORTAL and UNION filesystems are known to be
699 # buggy, and WILL panic your system if you attempt to do anything with
700 # them.  They are included here as an incentive for some enterprising
701 # soul to sit down and fix them.
702 #
703
704 # One of these is mandatory:
705 options         FFS                     #Fast filesystem
706 options         MFS                     #Memory filesystem
707 options         NFS                     #Network filesystem
708
709 # The rest are optional:
710 #options        NFS_NOSERVER            #Disable the NFS-server code.
711 options         CD9660                  #ISO 9660 filesystem
712 options         FDESC                   #File descriptor filesystem
713 options         HAMMER                  #HAMMER filesystem
714 options         HPFS                    #OS/2 File system
715 options         MSDOSFS                 #MS DOS filesystem
716 options         NTFS                    #NT filesystem
717 options         NULLFS                  #NULL filesystem
718 options         NWFS                    #NetWare filesystem
719 options         PORTAL                  #Portal filesystem
720 options         PROCFS                  #Process filesystem
721 options         SMBFS                   #SMB/CIFS filesystem
722 options         TMPFS                   #Temporary filesystem
723 options         UDF                     #UDF filesystem
724
725 # YYY-DR Till we rework the VOP methods for this filesystem
726 #options        UNION                   #Union filesystem
727 # The xFS_ROOT options REQUIRE the associated ``options xFS''
728 options         FFS_ROOT                #FFS usable as root device
729 options         NFS_ROOT                #NFS usable as root device
730
731 # Soft updates is technique for improving UFS filesystem speed and
732 # making abrupt shutdown less risky.
733 options         SOFTUPDATES
734
735 # Directory hashing improves the speed of operations on very large
736 # directories at the expense of some memory.
737 options         UFS_DIRHASH
738
739 # Make space in the kernel for a root filesystem on a md device.
740 # Define to the number of kilobytes to reserve for the filesystem.
741 options         MD_ROOT_SIZE=10
742
743 # Make the md device a potential root device, either with preloaded
744 # images of type mfs_root or md_root.
745 options         MD_ROOT
746
747 # Specify double the default maximum size for malloc(9)-backed md devices.
748 options         MD_NSECT=40000
749
750 # Allow this many swap-devices.
751 #
752 # In order to manage swap, the system must reserve bitmap space that
753 # scales with the largest mounted swap device multiplied by NSWAPDEV,
754 # regardless of whether other swap devices exist or not.  So it
755 # is not a good idea to make this value too large.
756 options         NSWAPDEV=5
757
758 # Disk quotas are supported when this option is enabled.
759 options         QUOTA                   #enable disk quotas
760
761 # If you are running a machine just as a fileserver for PC and MAC
762 # users, e.g. using SAMBA, you may consider setting this option
763 # and keeping all those users' directories on a filesystem that is
764 # mounted with the suiddir option. This gives new files the same
765 # ownership as the directory (similar to group). It's a security hole
766 # if you let these users run programs, so confine it to file-servers
767 # (but it'll save you lots of headaches in those cases). Root owned
768 # directories are exempt and X bits are cleared. The suid bit must be
769 # set on the directory as well; see chmod(1) PC owners can't see/set
770 # ownerships so they keep getting their toes trodden on. This saves
771 # you all the support calls as the filesystem it's used on will act as
772 # they expect: "It's my dir so it must be my file".
773 #
774 options         SUIDDIR
775
776 # NFS options:
777 options         NFS_MINATTRTIMO=3       # VREG attrib cache timeout in sec
778 options         NFS_MAXATTRTIMO=60
779 options         NFS_MINDIRATTRTIMO=30   # VDIR attrib cache timeout in sec
780 options         NFS_MAXDIRATTRTIMO=60
781 options         NFS_GATHERDELAY=10      # Default write gather delay (msec)
782 options         NFS_UIDHASHSIZ=29       # Tune the size of nfssvc_sock with this
783 options         NFS_WDELAYHASHSIZ=16    # and with this
784 options         NFS_MUIDHASHSIZ=63      # Tune the size of nfsmount with this
785 options         NFS_DEBUG               # Enable NFS Debugging
786
787 # MSDOSFS options:
788 options         MSDOSFS_DEBUG           # Enable MSDOSFS Debugging
789
790 #
791 # Add support for the EXT2FS filesystem of Linux fame.  Be a bit
792 # careful with this - the ext2fs code has a tendency to lag behind
793 # changes and not be exercised very much, so mounting read/write could
794 # be dangerous (and even mounting read only could result in panics.)
795 #
796 options         EXT2FS
797
798 # Optional character code conversion support with LIBICONV.
799 # Each option requires their base file system and LIBICONV.
800 options         CD9660_ICONV
801 options         MSDOSFS_ICONV
802 options         NTFS_ICONV
803
804 #####################################################################
805 # POSIX P1003.1B
806
807 # Real time extensions added in the 1993 Posix
808 # P1003_1B: Infrastructure
809 # _KPOSIX_PRIORITY_SCHEDULING: Build in _POSIX_PRIORITY_SCHEDULING
810 # _KPOSIX_VERSION:             Version kernel is built for
811
812 options         P1003_1B
813 options         _KPOSIX_PRIORITY_SCHEDULING
814 options         _KPOSIX_VERSION=199309L
815
816 #####################################################################
817 # CLOCK OPTIONS
818
819 # The granularity of operation is controlled by the kernel option HZ whose
820 # default value (100) means a granularity of 10ms (1s/HZ).
821 # Consider, however, that reducing the granularity too much might
822 # cause excessive overhead in clock interrupt processing,
823 # potentially causing ticks to be missed and thus actually reducing
824 # the accuracy of operation.
825
826 options         HZ=100
827
828 # The following options are used for debugging clock behavior only, and
829 # should not be used for production systems.
830 #
831 # CLK_CALIBRATION_LOOP will run the clock calibration loop at startup
832 # until the user presses a key.
833
834 options         CLK_CALIBRATION_LOOP
835
836 # The following two options measure the frequency of the corresponding
837 # clock relative to the RTC (onboard mc146818a).
838
839 options         CLK_USE_I8254_CALIBRATION
840 options         CLK_USE_TSC_CALIBRATION
841
842 #####################################################################
843 # SCSI DEVICES
844
845 # SCSI DEVICE CONFIGURATION
846
847 # The SCSI subsystem consists of the `base' SCSI code, a number of
848 # high-level SCSI device `type' drivers, and the low-level host-adapter
849 # device drivers.  The host adapters are listed in the ISA and PCI
850 # device configuration sections below.
851 #
852 # Beginning with FreeBSD 2.0.5 you can wire down your SCSI devices so
853 # that a given bus, target, and LUN always come on line as the same
854 # device unit.  In earlier versions the unit numbers were assigned
855 # in the order that the devices were probed on the SCSI bus.  This
856 # means that if you removed a disk drive, you may have had to rewrite
857 # your /etc/fstab file, and also that you had to be careful when adding
858 # a new disk as it may have been probed earlier and moved your device
859 # configuration around.
860
861 # This old behavior is maintained as the default behavior.  The unit
862 # assignment begins with the first non-wired down unit for a device
863 # type.  For example, if you wire a disk as "da3" then the first
864 # non-wired disk will be assigned da4.
865
866 # The syntax for wiring down devices is:
867
868 # device        scbus0 at ahc0          # Single bus device
869 # device        scbus1 at ahc1 bus 0    # Single bus device
870 # device        scbus3 at ahc2 bus 0    # Twin bus device
871 # device        scbus2 at ahc2 bus 1    # Twin bus device
872 # device        da0 at scbus0 target 0 unit 0
873 # device        da1 at scbus3 target 1
874 # device        da2 at scbus2 target 3
875 # device        sa1 at scbus1 target 6
876 # device        cd
877
878 # "units" (SCSI logical unit number) that are not specified are
879 # treated as if specified as LUN 0.
880
881 # All SCSI devices allocate as many units as are required.
882
883 # The "unknown" device (uk? in pre-2.0.5) is now part of the base SCSI
884 # configuration and doesn't have to be explicitly configured.
885
886 device          scbus                   #base SCSI code
887 device          ch                      #SCSI media changers
888 device          da                      #SCSI direct access devices (aka disks)
889 device          sa                      #SCSI tapes
890 device          cd                      #SCSI CD-ROMs
891 device          pass                    #CAM passthrough driver
892 device          sg                      #Passthrough device (linux scsi generic)
893 device          pt                      #SCSI processor type
894 device          ses                     #SCSI SES/SAF-TE driver
895
896 # Options for device mapper
897 device          dm
898 device          dm_target_crypt
899 device          dm_target_linear
900 device          dm_target_striped
901
902 # Options for iSCSI
903 device          iscsi_initiator
904 options         ISCSI_INITIATOR_DEBUG=8
905
906 # CAM OPTIONS:
907 # debugging options:
908 # -- NOTE --  If you specify one of the bus/target/lun options, you must
909 #             specify them all!
910 # CAMDEBUG: When defined enables debugging macros
911 # CAM_DEBUG_BUS:  Debug the given bus.  Use -1 to debug all busses.
912 # CAM_DEBUG_TARGET:  Debug the given target.  Use -1 to debug all targets.
913 # CAM_DEBUG_LUN:  Debug the given lun.  Use -1 to debug all luns.
914 # CAM_DEBUG_FLAGS:  OR together CAM_DEBUG_INFO, CAM_DEBUG_TRACE,
915 #                   CAM_DEBUG_SUBTRACE, and CAM_DEBUG_CDB
916 #
917 # CAM_MAX_HIGHPOWER: Maximum number of concurrent high power (start unit) cmds
918 # SCSI_NO_SENSE_STRINGS: When defined disables sense descriptions
919 # SCSI_NO_OP_STRINGS: When defined disables opcode descriptions
920 # SCSI_DELAY: The number of MILLISECONDS to freeze the SIM (scsi adapter)
921 #             queue after a bus reset, and the number of milliseconds to
922 #             freeze the device queue after a bus device reset.  This
923 #             can be changed at boot and runtime with the
924 #             kern.cam.scsi_delay tunable/sysctl.
925 options         CAMDEBUG
926 options         CAM_DEBUG_BUS=-1
927 options         CAM_DEBUG_TARGET=-1
928 options         CAM_DEBUG_LUN=-1
929 options         CAM_DEBUG_FLAGS="CAM_DEBUG_INFO|CAM_DEBUG_TRACE|CAM_DEBUG_CDB"
930 options         CAM_MAX_HIGHPOWER=4
931 options         SCSI_NO_SENSE_STRINGS
932 options         SCSI_NO_OP_STRINGS
933 options         SCSI_DELAY=8000 # Be pessimistic about Joe SCSI device
934
935 # Options for the CAM CDROM driver:
936 # CHANGER_MIN_BUSY_SECONDS: Guaranteed minimum time quantum for a changer LUN
937 # CHANGER_MAX_BUSY_SECONDS: Maximum time quantum per changer LUN, only
938 #                           enforced if there is I/O waiting for another LUN
939 # The compiled in defaults for these variables are 2 and 10 seconds,
940 # respectively.
941 #
942 # These can also be changed on the fly with the following sysctl variables:
943 # kern.cam.cd.changer.min_busy_seconds
944 # kern.cam.cd.changer.max_busy_seconds
945 #
946 options         CHANGER_MIN_BUSY_SECONDS=2
947 options         CHANGER_MAX_BUSY_SECONDS=10
948
949 # Options for the CAM sequential access driver:
950 # SA_IO_TIMEOUT: Timeout for read/write/wfm  operations, in minutes
951 # SA_SPACE_TIMEOUT: Timeout for space operations, in minutes
952 # SA_REWIND_TIMEOUT: Timeout for rewind operations, in minutes
953 # SA_ERASE_TIMEOUT: Timeout for erase operations, in minutes
954 # SA_1FM_AT_EOD: Default to model which only has a default one filemark at EOT.
955 options         SA_IO_TIMEOUT="(4)"
956 options         SA_SPACE_TIMEOUT="(60)"
957 options         SA_REWIND_TIMEOUT="(2*60)"
958 options         SA_ERASE_TIMEOUT="(4*60)"
959 options         SA_1FM_AT_EOD
960
961 # Optional timeout for the CAM processor target (pt) device
962 # This is specified in seconds.  The default is 60 seconds.
963 options         SCSI_PT_DEFAULT_TIMEOUT="60"
964
965 # Optional enable of doing SES passthrough on other devices (e.g., disks)
966 #
967 # Normally disabled because a lot of newer SCSI disks report themselves
968 # as having SES capabilities, but this can then clot up attempts to build
969 # build a topology with the SES device that's on the box these drives
970 # are in....
971 options         SES_ENABLE_PASSTHROUGH
972
973 #####################################################################
974 # MISCELLANEOUS DEVICES AND OPTIONS
975
976 # The `pty' device usually turns out to be ``effectively mandatory'',
977 # as it is required for `telnetd', `rlogind', `screen', `emacs', and
978 # `xterm', among others.
979
980 pseudo-device   pty             #Pseudo ttys
981 pseudo-device   gzip            #Exec gzipped a.out's
982 pseudo-device   vn              #Vnode driver (turns a file into a device)
983 pseudo-device   md              #Memory/malloc disk
984 pseudo-device   snp             #Snoop device - to look at pty/vty/etc..
985 pseudo-device   ccd     4       #Concatenated disk driver
986
987 # Configuring Vinum into the kernel is not necessary, since the kld
988 # module gets started automatically when vinum(8) starts.  This
989 # device is also untested.  Use at your own risk.
990 #
991 # The option VINUMDEBUG must match the value set in CFLAGS
992 # in src/sbin/vinum/Makefile.  Failure to do so will result in
993 # the following message from vinum(8):
994 #
995 # Can't get vinum config: Invalid argument
996 #
997 # see vinum(4) for more reasons not to use these options.
998 pseudo-device   vinum           #Vinum concat/mirror/raid driver
999 options         VINUMDEBUG      #enable Vinum debugging hooks
1000
1001 # Kernel side iconv library
1002 options         LIBICONV
1003
1004 # Size of the kernel message buffer.  Should be N * pagesize.
1005 options         MSGBUF_SIZE=40960
1006
1007 #####################################################################
1008 # HARDWARE DEVICE CONFIGURATION
1009
1010 # ISA devices:
1011
1012 #
1013 # Mandatory ISA devices: isa, npx
1014 #
1015 device          isa
1016
1017 # ISA-PnP BIOS support
1018 device          pnpbios
1019
1020 #
1021 # Options for `isa':
1022 #
1023 # AUTO_EOI_1 enables the `automatic EOI' feature for the master 8259A
1024 # interrupt controller.  This saves about 0.7-1.25 usec for each interrupt.
1025 # This option breaks suspend/resume on some portables.
1026 #
1027 # AUTO_EOI_2 enables the `automatic EOI' feature for the slave 8259A
1028 # interrupt controller.  This saves about 0.7-1.25 usec for each interrupt.
1029 # Automatic EOI is documented not to work for for the slave with the
1030 # original i8259A, but it works for some clones and some integrated
1031 # versions.
1032 #
1033 # MAXMEM specifies the amount of RAM on the machine; if this is not
1034 # specified, DragonFly will first read the amount of memory from the CMOS
1035 # RAM, so the amount of memory will initially be limited to 64MB or 16MB
1036 # depending on the BIOS.  If the BIOS reports 64MB, a memory probe will
1037 # then attempt to detect the installed amount of RAM.  If this probe
1038 # fails to detect >64MB RAM you will have to use the MAXMEM option.
1039 # The amount is in kilobytes, so for a machine with 128MB of RAM, it would
1040 # be 131072 (128 * 1024).
1041 #
1042 # BROKEN_KEYBOARD_RESET disables the use of the keyboard controller to
1043 # reset the CPU for reboot.  This is needed on some systems with broken
1044 # keyboard controllers.
1045
1046 options         COMPAT_OLDISA   #FreeBSD 2.2 and 3.x compatibility shims
1047 options         AUTO_EOI_1
1048 #options        AUTO_EOI_2
1049 options         MAXMEM="(128*1024)"
1050 #options        BROKEN_KEYBOARD_RESET
1051
1052 # Enable support for the kernel PLL to use an external PPS signal,
1053 # under supervision of [x]ntpd(8)
1054 # More info in ntpd documentation: http://www.eecis.udel.edu/~ntp
1055
1056 options         PPS_SYNC
1057
1058 # The keyboard controller; it controls the keyboard and the PS/2 mouse.
1059 device          atkbdc0 at isa? port IO_KBD
1060
1061 # The AT keyboard
1062 device          atkbd0  at atkbdc? irq 1
1063
1064 # Options for atkbd:
1065 options         ATKBD_DFLT_KEYMAP       # specify the built-in keymap
1066 makeoptions     ATKBD_DFLT_KEYMAP="jp.106"
1067
1068 # These options are valid for other keyboard drivers as well.
1069 options         KBD_DISABLE_KEYMAP_LOAD # refuse to load a keymap
1070 options         KBD_INSTALL_CDEV        # install a CDEV entry in /dev
1071
1072 # `flags' for atkbd:
1073 #       0x01    Force detection of keyboard, else we always assume a keyboard
1074 #       0x02    Don't reset keyboard, useful for some newer ThinkPads
1075 #       0x03    Force detection and avoid reset, might help with certain
1076 #               dockingstations
1077 #       0x04    Old-style (XT) keyboard support, useful for older ThinkPads
1078
1079 # PS/2 mouse
1080 device          psm0    at atkbdc? irq 12
1081
1082 # Options for psm:
1083 options         PSM_HOOKRESUME          #hook the system resume event, useful
1084                                         #for some laptops
1085 options         PSM_RESETAFTERSUSPEND   #reset the device at the resume event
1086
1087 device          kbdmux                  # keyboard multiplexer
1088
1089 # The video card driver.
1090 device          vga0    at isa?
1091
1092 # Options for vga:
1093 # Try the following option if the mouse pointer is not drawn correctly
1094 # or font does not seem to be loaded properly.  May cause flicker on
1095 # some systems.
1096 options         VGA_ALT_SEQACCESS
1097
1098 options         VGA_DEBUG=2             # enable VGA debug output
1099
1100 # If you experience problems switching back to 80x25 (or a derived mode),
1101 # the following option might help.
1102 #options        VGA_KEEP_POWERON_MODE   # use power-on settings for 80x25
1103
1104 # If you can dispense with some vga driver features, you may want to
1105 # use the following options to save some memory.
1106 #options        VGA_NO_FONT_LOADING     # don't save/load font
1107 #options        VGA_NO_MODE_CHANGE      # don't change video modes
1108
1109 # The following option probably won't work with the LCD displays.
1110 options         VGA_WIDTH90             # support 90 column modes
1111
1112 # To include support for VESA video modes
1113 options         VESA
1114 options         VESA_DEBUG=2            # enable VESA debug output
1115
1116 # Splash screen at start up!  Screen savers require this too.
1117 pseudo-device   splash
1118
1119 # The syscons console driver (sco color console compatible).
1120 device          sc0     at isa?
1121 options         MAXCONS=16              # number of virtual consoles
1122 options         SC_ALT_MOUSE_IMAGE      # simplified mouse cursor in text mode
1123 options         SC_DEBUG_LEVEL=5        # enable debug output
1124 options         SC_DFLT_FONT            # compile font in
1125 makeoptions     SC_DFLT_FONT=cp850
1126 options         SC_DISABLE_DDBKEY       # disable `debug' key
1127 options         SC_DISABLE_REBOOT       # disable reboot key sequence
1128 options         SC_HISTORY_SIZE=200     # number of history buffer lines
1129 options         SC_MOUSE_CHAR=0x3       # char code for text mode mouse cursor
1130 options         SC_PIXEL_MODE           # add support for the raster text mode
1131
1132 # The following options will let you change the default colors of syscons.
1133 options         SC_NORM_ATTR="(FG_GREEN|BG_BLACK)"
1134 options         SC_NORM_REV_ATTR="(FG_YELLOW|BG_GREEN)"
1135 options         SC_KERNEL_CONS_ATTR="(FG_RED|BG_BLACK)"
1136 options         SC_KERNEL_CONS_REV_ATTR="(FG_BLACK|BG_RED)"
1137
1138 # If you have a two button mouse, you may want to add the following option
1139 # to use the right button of the mouse to paste text.
1140 options         SC_TWOBUTTON_MOUSE
1141
1142 # You can selectively disable features in syscons.
1143 #options        SC_NO_CUTPASTE
1144 #options        SC_NO_FONT_LOADING
1145 #options        SC_NO_HISTORY
1146 #options        SC_NO_SYSMOUSE
1147
1148 #
1149 # The Numeric Processing eXtension driver.  In addition to this, you
1150 # may configure a math emulator (see above).  If your machine has a
1151 # hardware FPU and the kernel configuration includes the npx device
1152 # *and* a math emulator compiled into the kernel, the hardware FPU
1153 # will be used, unless it is found to be broken or unless "flags" to
1154 # npx0 includes "0x08", which requests preference for the emulator.
1155 device          npx0    at nexus? port IO_NPX flags 0x0 irq 13
1156
1157 #
1158 # `flags' for npx0:
1159 #       0x01    don't use the npx registers to optimize bcopy.
1160 #       0x02    don't use the npx registers to optimize bzero.
1161 #       0x04    don't use the npx registers to optimize copyin or copyout.
1162 #       0x08    use emulator even if hardware FPU is available.
1163 # The npx registers are normally used to optimize copying and zeroing when
1164 # all of the following conditions are satisfied:
1165 #       I586_CPU is an option
1166 #       the cpu is an i586 (perhaps not a Pentium)
1167 #       the probe for npx0 succeeds
1168 #       INT 16 exception handling works.
1169 # Then copying and zeroing using the npx registers is normally 30-100% faster.
1170 # The flags can be used to control cases where it doesn't work or is slower.
1171 # Setting them at boot time using userconfig works right (the optimizations
1172 # are not used until later in the bootstrap when npx0 is attached).
1173 # Flag 0x08 automatically disables the i586 optimized routines.
1174 #
1175
1176 #
1177 # Optional ISA devices:
1178 #
1179
1180 #
1181 # SCSI host adapters: `aic' and `bt'
1182 #
1183 # adv: All Narrow SCSI bus AdvanSys controllers.
1184 # adw: Second Generation AdvanSys controllers including the ADV940UW.
1185 # ahc: Adaptec 274x/284x/294x
1186 # aic: Adaptec 152x
1187 # bt: Most Buslogic controllers
1188 # ncv: NCR 53C500 based SCSI host adapters.
1189 # nsp: Workbit Ninja SCSI-3 based PC Card SCSI host adapters.
1190 # stg: TMC 18C30, 18C50 based ISA/PC Card SCSI host adapters.
1191 #
1192 # Note that the order is important in order for Buslogic cards to be
1193 # probed correctly.
1194 #
1195
1196 device          bt0     at isa? port IO_BT0
1197 device          adv0    at isa?
1198 device          adw
1199 device          aic0    at isa?
1200 device          ncv
1201 device          nsp
1202 device          stg0    at isa? port 0x140 irq 11
1203
1204 #
1205 # Adaptec FSA RAID controllers, including integrated DELL controller,
1206 # the Dell PERC 2/QC and the HP NetRAID-4M
1207 #
1208 device          aac
1209 options         AAC_DEBUG
1210 device          aacp    # SCSI Passthrough interface (optional, CAM required)
1211
1212 #
1213 # Compaq Smart RAID, Mylex DAC960 and AMI MegaRAID controllers.  Only
1214 # one entry is needed; the code will find and configure all supported
1215 # controllers.
1216 #
1217 device          ida             # Compaq Smart RAID
1218 device          mlx             # Mylex DAC960
1219 device          amr             # AMI MegaRAID
1220 device          amrp            # SCSI Passthrough interface (optional, CAM req.)
1221 device          mfi             # LSI MegaRAID SAS
1222 device          mfip            # LSI MegaRAID SAS passthrough, requires CAM
1223 options         MFI_DEBUG
1224
1225 #
1226 # Areca RAID (CAM is required).
1227 #
1228 device          arcmsr          # Areca SATA II RAID
1229
1230 #
1231 # Highpoint RocketRAID 182x.
1232 device          hptmv
1233
1234 #
1235 # Highpoint RocketRaid 3xxx series SATA RAID
1236 device          hptiop
1237
1238 #
1239 # 3ware ATA RAID
1240 #
1241 device          twe             # 3ware ATA RAID
1242 device          twa             # 3ware 9000 series PATA/SATA RAID
1243 options         TWA_DEBUG=10    # enable debug messages
1244 device          tws             # 3ware 9750 series SATA/SAS RAID
1245
1246 #
1247 # Promise Supertrack SX6000
1248 #
1249 device          pst
1250
1251 #
1252 # IBM ServeRAID
1253 #
1254 device  ips
1255
1256 # AHCI driver, this will override NATA for AHCI devices,
1257 # both drivers may be included.
1258 #
1259 device          ahci
1260
1261 # SiI3124/3132 driver
1262 #
1263 device          sili
1264
1265 # The 'NATA' driver supports all ATA and ATAPI devices.
1266 # You only need one "device nata" for it to find all
1267 # PCI ATA/ATAPI devices on modern machines.
1268 #
1269 device          nata
1270 device          natadisk        # ATA disk drives
1271 device          natapicd        # ATAPI CD/DVD drives
1272 device          natapifd        # ATAPI floppy drives
1273 device          natapist        # ATAPI tape drives
1274 device          natapicam       # ATAPI CAM layer emulation
1275 device          nataraid        # support for ATA software RAID controllers
1276 device          natausb         # ATA-over-USB support
1277
1278 # The following options are valid for the NATA driver:
1279 #
1280 # ATA_STATIC_ID:        controller numbering is static (like the old driver)
1281 #                       else the device numbers are dynamically allocated.
1282 options         ATA_STATIC_ID
1283
1284 # For older non-PCI systems, these are the lines to use:
1285 #
1286 #device         nata0   at isa? port IO_WD1 irq 14
1287 #device         nata1   at isa? port IO_WD2 irq 15
1288
1289 #
1290 # Standard floppy disk controllers: `fdc' and `fd'
1291 #
1292 device          fdc0    at isa? port IO_FD1 irq 6 drq 2
1293 #
1294 # FDC_DEBUG enables floppy debugging.  Since the debug output is huge, you
1295 # gotta turn it actually on by setting the variable fd_debug with DDB,
1296 # however.
1297 options         FDC_DEBUG
1298
1299 device          fd0     at fdc0 drive 0
1300 device          fd1     at fdc0 drive 1
1301
1302 #
1303 # sio: serial ports (see sio(4))
1304
1305 device          sio0    at isa? port IO_COM1 flags 0x10 irq 4
1306
1307 #
1308 # `flags' for serial drivers that support consoles (only for sio now):
1309 #       0x10    enable console support for this unit.  The other console flags
1310 #               are ignored unless this is set.  Enabling console support does
1311 #               not make the unit the preferred console - boot with -h or set
1312 #               the 0x20 flag for that.  Currently, at most one unit can have
1313 #               console support; the first one (in config file order) with
1314 #               this flag set is preferred.  Setting this flag for sio0 gives
1315 #               the old behaviour.
1316 #       0x20    force this unit to be the console (unless there is another
1317 #               higher priority console).  This replaces the COMCONSOLE option.
1318 #       0x40    reserve this unit for low level console operations.  Do not
1319 #               access the device in any normal way.
1320 #       0x80    use this port for serial line gdb support in ddb.
1321 #
1322 # PnP `flags' (set via userconfig using pnp x flags y)
1323 #       0x1     disable probing of this device.  Used to prevent your modem
1324 #               from being attached as a PnP modem.
1325 #
1326
1327 # Options for serial drivers that support consoles (only for sio now):
1328 options         BREAK_TO_DEBUGGER       #a BREAK on a comconsole goes to
1329                                         #DDB, if available.
1330 options         CONSPEED=115200         # speed for serial console
1331                                         # (default 9600)
1332
1333 # Solaris implements a new BREAK which is initiated by a character
1334 # sequence CR ~ ^b which is similar to a familiar pattern used on
1335 # Sun servers by the Remote Console.
1336 options         ALT_BREAK_TO_DEBUGGER
1337
1338 # Options for sio:
1339 options         COM_ESP                 #code for Hayes ESP
1340 options         COM_MULTIPORT           #code for some cards with shared IRQs
1341
1342 # Other flags for sio that aren't documented in the man page.
1343 #       0x20000 enable hardware RTS/CTS and larger FIFOs.  Only works for
1344 #               ST16650A-compatible UARTs.
1345
1346 # PCI Universal Communications driver
1347 # Supports various single and multi port PCI serial cards. Maybe later
1348 # also the parallel ports on combination serial/parallel cards. New cards
1349 # can be added in src/sys/dev/misc/puc/pucdata.c.
1350 device          puc
1351
1352 #
1353 # Network interfaces: `ed', `ep', `is', `lnc'
1354 #
1355 # ar: Arnet SYNC/570i hdlc sync 2/4 port V.35/X.21 serial driver (requires sppp)
1356 # cs: IBM Etherjet and other Crystal Semi CS89x0-based adapters
1357 # ed: Western Digital and SMC 80xx; Novell NE1000 and NE2000; 3Com 3C503
1358 # ep: 3Com 3C509
1359 # ex: Intel EtherExpress Pro/10 and other i82595-based adapters
1360 # fe: Fujitsu MB86960A/MB86965A Ethernet
1361 # lnc: Lance/PCnet cards (Isolan, Novell NE2100, NE32-VL, AMD Am7990 & Am79C960)
1362 # sbni: Granch SBNI12-xx adapters
1363 # sbsh: Granch SBNI16 SHDSL modem PCI adapters
1364 # sr: RISCom/N2 hdlc sync 1/2 port V.35/X.21 serial driver (requires sppp)
1365 # wi: Lucent WaveLAN/IEEE 802.11 PCMCIA adapters. Note: this supports both
1366 #     the PCMCIA and ISA cards: the ISA card is really a PCMCIA to ISA
1367 #     bridge with a PCMCIA adapter plugged into it.
1368 # an: Aironet 4500/4800 802.11 wireless adapters. Supports the PCMCIA,
1369 #     PCI and ISA varieties.
1370 # xe: Xircom/Intel EtherExpress Pro100/16 PC Card ethernet controller.
1371 #
1372 device ar0 at isa? port 0x300 irq 10 iomem 0xd0000
1373 device cs0 at isa? port 0x300
1374 device ed0 at isa? port 0x280 irq 5 iomem 0xd8000
1375 device ep
1376 device ex
1377 device fe0 at isa? port 0x300
1378 device lnc0 at isa? port 0x280 irq 10 drq 0
1379 device sbni0 at isa? port 0x210 irq 5 flags 0xefdead
1380 device sln
1381 device sr
1382 device sn0 at isa? port 0x300 irq 10
1383
1384 # Wlan support is mandatory for some wireless LAN devices.
1385 options         IEEE80211_DEBUG         #enable debugging msgs
1386 options         IEEE80211_AMPDU_AGE     #age frames in AMPDU reorder q's
1387 options         IEEE80211_SUPPORT_MESH  #enable 802.11s D3.0 support
1388 options         IEEE80211_SUPPORT_TDMA  #enable TDMA support
1389 device          wlan            # 802.11 support
1390 device          wlan_acl        # 802.11 MAC-based access control for AP
1391 device          wlan_ccmp       # 802.11 CCMP support
1392 device          wlan_tkip       # 802.11 TKIP support
1393 device          wlan_wep        # 802.11 WEP support
1394 device          wlan_xauth      # 802.11 WPA or 802.1x authentication for AP
1395 device          wlan_amrr       # 802.11 AMRR TX rate control algorithm
1396 device          an              # Aironet Communications 4500/4800
1397 device          ath             # Atheros AR521x
1398 options         AH_SUPPORT_AR5416
1399 device          ath_hal         # Atheros Hardware Access Layer
1400 #device         ath_rate_amrr   # Atheros AMRR TX rate control algorithm
1401 #device         ath_rate_onoe   # Atheros Onoe TX rate control algorithm
1402 device          ath_rate_sample # Atheros Sample TX rate control algorithm
1403 options         ATH_DEBUG       # turn on debugging output (see hw.ath.debug)
1404 options         ATH_DIAGAPI     # diagnostic interface to the HAL
1405 options         ATH_RXBUF=80    # number of RX buffers to allocate
1406 options         ATH_TXBUF=400   # number of TX buffers to allocate
1407 #device         iwl             # Intel PRO/Wireless 2100
1408 device          iwi             # Intel PRO/Wireless 2200BG/2915ABG
1409 device          iwn             # Intel WiFi Link 4965/1000/5000/5150/5300/6000/6050
1410 device          wi              # WaveLAN/IEEE, PRISM-II, Spectrum24 802.11DS
1411 #device         rtw             # RealTek 8180
1412 #device         acx             # TI ACX100/ACX111.
1413 device          xe              # Xircom PCMCIA
1414 device          ral             # Ralink Technology 802.11 wireless NIC
1415 device          wpi
1416
1417 # IEEE 802.11 adapter firmware modules
1418
1419 # iwifw:        Intel PRO/Wireless 2200BG/2225BG/2915ABG firmware
1420 # iwnfw:        Intel WiFi Link 4965/1000/5000/5150/5300/6000/6050
1421 # ralfw:        Ralink Technology RT25xx and RT26xx firmware
1422 # wpifw:        Intel 3945ABG Wireless LAN Controller firmware
1423
1424 device          iwifw
1425 device          iwnfw
1426 device          ralfw
1427 device          wpifw
1428
1429 # Bluetooth Protocols
1430 device          bluetooth
1431
1432 #
1433 # ATM related options
1434 #
1435 # The `en' device provides support for Efficient Networks (ENI)
1436 # ENI-155 PCI midway cards, and the Adaptec 155Mbps PCI ATM cards (ANA-59x0).
1437 #
1438 # atm pseudo-device provides generic atm functions and is required for
1439 # atm devices.
1440 # NATM enables the netnatm protocol family that can be used to
1441 # bypass TCP/IP.
1442 #
1443 # the current driver supports only PVC operations (no atm-arp, no multicast).
1444 # for more details, please read the original documents at
1445 # http://www.ccrc.wustl.edu/pub/chuck/tech/bsdatm/bsdatm.html
1446 #
1447 pseudo-device   atm
1448 device          en
1449 options         NATM                    #native ATM
1450
1451 # Sound drivers
1452 #
1453 # The flags of the device tells the device a bit more info about the
1454 # device that normally is obtained through the PnP interface.
1455 #       bit  2..0   secondary DMA channel;
1456 #       bit  4      set if the board uses two dma channels;
1457 #       bit 15..8   board type, overrides autodetection; leave it
1458 #                   zero if don't know what to put in (and you don't,
1459 #                   since this is unsupported at the moment...).
1460 #
1461 # This driver will use the new PnP code if it's available. You might
1462 # need PNPBIOS for ISA devices.
1463 #
1464 # If you have a GUS-MAX card and want to use the CS4231 codec on the
1465 # card the drqs for the gus max must be 8 bit (1, 2, or 3).
1466 #
1467 # If you would like to use the full duplex option on the gus, then define
1468 # flags to be the ``read dma channel''.
1469 #
1470
1471 # Basic sound card support:
1472 device          pcm
1473 # For PnP/PCI sound cards:
1474 device          "snd_ad1816"
1475 device          "snd_als4000"
1476 device          "snd_atiixp"
1477 device          "snd_cmi"
1478 device          "snd_cs4281"
1479 device          "snd_csa"
1480 device          "snd_ds1"
1481 device          "snd_emu10k1"
1482 device          "snd_es137x"
1483 device          "snd_ess"
1484 device          "snd_fm801"
1485 device          "snd_gusc"
1486 device          "snd_hda"
1487 device          "snd_ich"
1488 device          "snd_maestro"
1489 device          "snd_maestro3"
1490 device          "snd_mss"
1491 device          "snd_neomagic"
1492 device          "snd_sb16"
1493 device          "snd_sb8"
1494 device          "snd_sbc"
1495 device          "snd_solo"
1496 device          "snd_t4dwave"
1497 device          "snd_via8233"
1498 device          "snd_via82c686"
1499 device          "snd_vibes"
1500 # For non-pnp sound cards:
1501 device          pcm0 at isa? irq 10 drq 1 flags 0x0
1502 # USB
1503 device          "snd_uaudio"
1504
1505 #
1506 # Miscellaneous hardware:
1507 #
1508 # apm: Laptop Advanced Power Management (experimental)
1509 # bktr: Brooktree bt848/848a/849a/878/879 video capture and TV Tuner board
1510 # cy: Cyclades serial driver
1511 # ecc: ECC memory controller
1512 # joy: joystick
1513 # rp: Comtrol Rocketport(ISA) - single card
1514 # si: Specialix SI/XIO 4-32 port terminal multiplexor
1515 # spic: Sony Programmable I/O controller (VAIO notebooks)
1516 # stl: Stallion EasyIO and EasyConnection 8/32 (ISA and PCI), EasyConnection 8/64 PCI
1517 # stli: Stallion EasyConnection 8/64 ISA, ONboard, Brumby (intelligent)
1518 # nmdm: nullmodem terminal driver (see nmdm(4))
1519
1520 # Notes on APM
1521 #  The flags takes the following meaning for apm0:
1522 #    0x0020  Statclock is broken.
1523 #  If apm is omitted, some systems require sysctl -w kern.timecounter.method=1
1524 #  for correct timekeeping.
1525
1526 # Notes on the Comtrol Rocketport driver:
1527 #
1528 # The exact values used for rp0 depend on how many boards you have
1529 # in the system.  The manufacturer's sample configs are listed as:
1530 #
1531 #   Comtrol Rocketport ISA single card
1532 #               device  rp0     at isa? port 0x280
1533 #
1534 #   If instead you have two ISA cards, one installed at 0x100 and the
1535 #   second installed at 0x180, then you should add the following to
1536 #   your kernel configuration file:
1537 #
1538 #               device  rp0     at isa? port 0x100
1539 #               device  rp1     at isa? port 0x180
1540 #
1541 #   For 4 ISA cards, it might be something like this:
1542 #
1543 #               device  rp0     at isa? port 0x180
1544 #               device  rp1     at isa? port 0x100
1545 #               device  rp2     at isa? port 0x340
1546 #               device  rp3     at isa? port 0x240
1547 #
1548 #   And for PCI cards, you only need say:
1549 #
1550 #               device rp
1551
1552 # Notes on the Specialix SI/XIO driver:
1553 #  **This is NOT a Specialix supported Driver!**
1554 #  The host card is memory, not IO mapped.
1555 #  The Rev 1 host cards use a 64K chunk, on a 32K boundary.
1556 #  The Rev 2 host cards use a 32K chunk, on a 32K boundary.
1557 #  The cards can use an IRQ of 11, 12 or 15.
1558
1559 # Notes on the Stallion stl and stli drivers:
1560 #  See src/sys/platform/pc32/isa/README.stl for complete instructions.
1561 #  This is version 2.0.0, unsupported by Stallion.
1562 #  The stl driver has a secondary IO port hard coded at 0x280.  You need
1563 #     to change src/sys/dev/serial/stl/stallion.c if you reconfigure this on the boards.
1564 #  The "flags" and "iosiz" settings on the stli driver depend on the board:
1565 #       EasyConnection 8/64 ISA:     flags 23         iosiz 0x1000
1566 #       ONboard ISA:                 flags 4          iosiz 0x10000
1567 #       Brumby:                      flags 2          iosiz 0x4000
1568 #       Stallion:                    flags 1          iosiz 0x10000
1569 #  For the PCI cards, "device stl" will suffice.
1570
1571 device          apm0
1572 device          ecc
1573 device          joy0    at isa? port IO_GAME
1574 device          cy0     at isa? irq 10 iomem 0xd4000 iosiz 0x2000
1575 device          nrp
1576 device          si0     at isa? iomem 0xd0000 irq 12
1577 device          spic0   at isa? irq 0 port 0x10a0
1578 device          stl0    at isa? port 0x2a0 irq 10
1579 device          stli0   at isa? port 0x2a0 iomem 0xcc000 flags 23 iosiz 0x1000
1580 # nullmodem terminal driver
1581 device          nmdm
1582
1583 # The `ahc' device provides support for the Adaptec 274X and 284X
1584 # adapters.
1585 device          ahc
1586
1587 # The aic7xxx driver will attempt to use memory mapped I/O for all PCI
1588 # controllers that have it configured only if this option is set. Unfortunately,
1589 # this doesn't work on some motherboards, which prevents it from being the
1590 # default.
1591 options         AHC_ALLOW_MEMIO
1592
1593 # The adw driver will attempt to use memory mapped I/O for all PCI
1594 # controllers that have it configured only if this option is set.
1595 options         ADW_ALLOW_MEMIO
1596
1597 #
1598 # PCI devices & PCI options:
1599 #
1600 # The main PCI bus device is `pci'.  It provides auto-detection and
1601 # configuration support for all devices on the PCI bus, using either
1602 # configuration mode defined in the PCI specification.
1603
1604 device          pci
1605
1606 # PCI options
1607 #
1608 #Enable pci resources left off by a "lazy" BIOS.
1609 #
1610 options         COMPAT_OLDPCI   #FreeBSD 2.2 and 3.x compatibility shims
1611
1612 # AGP GART support
1613 #
1614 device          agp
1615
1616
1617 # The `ahc' device provides support for the Adaptec 29/3940(U)(W)
1618 # and motherboard based AIC7870/AIC7880 adapters.
1619 options         AHC_DEBUG
1620 options         AHC_DEBUG_OPTS=0xffffffff
1621 options         AHC_REG_PRETTY_PRINT
1622 options         AHC_TMODE_ENABLE
1623 #
1624 # The 'ahd' device provides support for the Adaptec 79xx Ultra320
1625 # SCSI adapters. Options are documented in the ahd(4) manpage:
1626 options         AHD_DEBUG
1627 options         AHD_DEBUG_OPTS=0xffffffff
1628 options         AHD_REG_PRETTY_PRINT
1629 #options        AHD_TMODE_ENABLE=0xff
1630 #
1631 # The `amd' device provides support for the AMD 53C974 SCSI host
1632 # adapter chip as found on devices such as the Tekram DC-390(T).
1633 #
1634 # The `bge' device provides support for gigabit ethernet adapters
1635 # based on the Broadcom BCM570x family of controllers, including the
1636 # 3Com 3c996-T, the Netgear GA302T, the SysKonnect SK-9D21 and SK-9D41,
1637 # and the embedded gigE NICs on Dell PowerEdge 2550 servers.
1638 #
1639 # The `ncr' device provides support for the NCR 53C810 and 53C825
1640 # self-contained SCSI host adapters.
1641 #
1642 # The `isp' device provides support for the Qlogic ISP 1020, 1040
1643 # nd 1040B PCI SCSI host adapters, ISP 1240 Dual Ultra SCSI,
1644 # ISP 1080 and 1280 (Dual) Ultra2, ISP 12160 Ultra3 SCSI, as well as
1645 # the Qlogic ISP 2100 and ISP 2200 Fibre Channel Host Adapters.
1646 #
1647 # The `dc' device provides support for PCI fast ethernet adapters
1648 # based on the DEC/Intel 21143 and various workalikes including:
1649 # the ADMtek AL981 Comet and AN985 Centaur, the ASIX Electronics
1650 # AX88140A and AX88141, the Davicom DM9100 and DM9102, the Lite-On
1651 # 82c168 and 82c169 PNIC, the Lite-On/Macronix LC82C115 PNIC II
1652 # and the Macronix 98713/98713A/98715/98715A/98725 PMAC. This driver
1653 # replaces the old al, ax, dm, pn and mx drivers.  List of brands:
1654 # Digital DE500-BA, Kingston KNE100TX, D-Link DFE-570TX, SOHOware SFA110,
1655 # SVEC PN102-TX, CNet Pro110B, 120A, and 120B, Compex RL100-TX,
1656 # LinkSys LNE100TX, LNE100TX V2.0, Jaton XpressNet, Alfa Inc GFC2204,
1657 # KNE110TX.
1658 #
1659 # The `de' device provides support for the Digital Equipment DC21040
1660 # self-contained Ethernet adapter.
1661 #
1662 # The `em' device provides support for the Intel Pro/1000 Family of Gigabit
1663 # adapters (82542, 82543, 82544, 82540).
1664 #
1665 # The `et' device provides support for the Agere ET1310 10/100/1000 PCIe
1666 # adapters.
1667 #
1668 # The `fxp' device provides support for the Intel EtherExpress Pro/100B
1669 # PCI Fast Ethernet adapters.
1670 #
1671 # The 'lge' device provides support for PCI gigabit ethernet adapters
1672 # based on the Level 1 LXT1001 NetCellerator chipset. This includes the
1673 # D-Link DGE-500SX, SMC TigerCard 1000 (SMC9462SX), and some Addtron cards.
1674 #
1675 # The 'my' device provides support for the Myson MTD80X and MTD89X PCI
1676 # Fast Ethernet adapters.
1677 #
1678 # The 'nge' device provides support for PCI gigabit ethernet adapters
1679 # based on the National Semiconductor DP83820 and DP83821 chipset. This
1680 # includes the SMC EZ Card 1000 (SMC9462TX), D-Link DGE-500T, Asante
1681 # FriendlyNet GigaNIX 1000TA and 1000TPC, the Addtron AEG320T, the
1682 # LinkSys EG1032 and EG1064, the Surecom EP-320G-TX and the Netgear GA622T.
1683 #
1684 # The 'pcn' device provides support for PCI fast ethernet adapters based
1685 # on the AMD Am79c97x chipsets, including the PCnet/FAST, PCnet/FAST+,
1686 # PCnet/PRO and PCnet/Home. These were previously handled by the lnc
1687 # driver (and still will be if you leave this driver out of the kernel).
1688 #
1689 # Te 're' device provides support for PCI GigaBit ethernet adapters based
1690 # on the RealTek 8169 chipset. It also supports the 8139C+ and is the
1691 # preferred driver for that chip.
1692 #
1693 # The 'rl' device provides support for PCI fast ethernet adapters based
1694 # on the RealTek 8129/8139 chipset. Note that the RealTek driver defaults
1695 # to using programmed I/O to do register accesses because memory mapped
1696 # mode seems to cause severe lockups on SMP hardware. This driver also
1697 # supports the Accton EN1207D `Cheetah' adapter, which uses a chip called
1698 # the MPX 5030/5038, which is either a RealTek in disguise or a RealTek
1699 # workalike.  Note that the D-Link DFE-530TX+ uses the RealTek chipset
1700 # and is supported by this driver, not the 'vr' driver.
1701 #
1702 # The 'sf' device provides support for Adaptec Duralink PCI fast
1703 # ethernet adapters based on the Adaptec AIC-6915 "starfire" controller.
1704 # This includes dual and quad port cards, as well as one 100baseFX card.
1705 # Most of these are 64-bit PCI devices, except for one single port
1706 # card which is 32-bit.
1707 #
1708 # The 'ste' device provides support for adapters based on the Sundance
1709 # Technologies ST201 PCI fast ethernet controller. This includes the
1710 # D-Link DFE-550TX.
1711 #
1712 # The 'sis' device provides support for adapters based on the Silicon
1713 # Integrated Systems SiS 900 and SiS 7016 PCI fast ethernet controller
1714 # chips.
1715 #
1716 # The 'sk' device provides support for the SysKonnect SK-984x series
1717 # PCI gigabit ethernet NICs. This includes the SK-9841 and SK-9842
1718 # single port cards (single mode and multimode fiber) and the
1719 # SK-9843 and SK-9844 dual port cards (also single mode and multimode).
1720 # The driver will autodetect the number of ports on the card and
1721 # attach each one as a separate network interface.
1722 #
1723 # The 'ti' device provides support for PCI gigabit ethernet NICs based
1724 # on the Alteon Networks Tigon 1 and Tigon 2 chipsets. This includes the
1725 # Alteon AceNIC, the 3Com 3c985, the Netgear GA620 and various others.
1726 # Note that you will probably want to bump up NMBCLUSTERS a lot to use
1727 # this driver.
1728 #
1729 # The 'tl' device provides support for the Texas Instruments TNETE100
1730 # series 'ThunderLAN' cards and integrated ethernet controllers. This
1731 # includes several Compaq Netelligent 10/100 cards and the built-in
1732 # ethernet controllers in several Compaq Prosignia, Proliant and
1733 # Deskpro systems. It also supports several Olicom 10Mbps and 10/100
1734 # boards.
1735 #
1736 # The `tx' device provides support for the SMC 9432 TX, BTX and FTX cards.
1737 #
1738 # The `txp' device provides support for the 3Com 3cR990 "Typhoon"
1739 # 10/100 adapters.
1740 #
1741 # The `vr' device provides support for various fast ethernet adapters
1742 # based on the VIA Technologies VT3043 `Rhine I' and VT86C100A `Rhine II'
1743 # chips, including the D-Link DFE530TX (see 'rl' for DFE530TX+), the Hawking
1744 # Technologies PN102TX, and the AOpen/Acer ALN-320.
1745 #
1746 # The `vx' device provides support for the 3Com 3C590 and 3C595
1747 # early support
1748 #
1749 # The `wb' device provides support for various fast ethernet adapters
1750 # based on the Winbond W89C840F chip. Note: this is not the same as
1751 # the Winbond W89C940F, which is an NE2000 clone.
1752 #
1753 # The `xl' device provides support for the 3Com 3c900, 3c905 and
1754 # 3c905B (Fast) Etherlink XL cards and integrated controllers. This
1755 # includes the integrated 3c905B-TX chips in certain Dell Optiplex and
1756 # Dell Precision desktop machines and the integrated 3c905-TX chips
1757 # in Dell Latitude laptop docking stations.
1758 #
1759 # The 'bktr' device is a PCI video capture device using the Brooktree
1760 # bt848/bt848a/bt849a/bt878/bt879 chipset. When used with a TV Tuner it forms a
1761 # TV card, eg Miro PC/TV, Hauppauge WinCast/TV WinTV, VideoLogic Captivator,
1762 # Intel Smart Video III, AverMedia, IMS Turbo, FlyVideo.
1763 #
1764 # options       OVERRIDE_CARD=xxx
1765 # options       OVERRIDE_TUNER=xxx
1766 # options       OVERRIDE_MSP=1
1767 # options       OVERRIDE_DBX=1
1768 # These options can be used to override the auto detection
1769 # The current values for xxx are found in src/sys/dev/video/bktr/bktr_card.h
1770 # Using sysctl(8) run-time overrides on a per-card basis can be made
1771 #
1772 # options       BKTR_SYSTEM_DEFAULT=BROOKTREE_PAL
1773 # or
1774 # options       BKTR_SYSTEM_DEFAULT=BROOKTREE_NTSC
1775 # Specifes the default video capture mode.
1776 # This is required for Dual Crystal (28&35Mhz) boards where PAL is used
1777 # to prevent hangs during initialisation.  eg VideoLogic Captivator PCI.
1778 #
1779 # options       BKTR_USE_PLL
1780 # PAL or SECAM users who have a 28Mhz crystal (and no 35Mhz crystal)
1781 # must enable PLL mode with this option. eg some new Bt878 cards.
1782 #
1783 # options       BKTR_GPIO_ACCESS
1784 # This enable IOCTLs which give user level access to the GPIO port.
1785 #
1786 # options       BKTR_NO_MSP_RESET
1787 # Prevents the MSP34xx reset. Good if you initialise the MSP in another OS first
1788 #
1789 # options       BKTR_430_FX_MODE
1790 # Switch Bt878/879 cards into Intel 430FX chipset compatibility mode.
1791 #
1792 # options       BKTR_SIS_VIA_MODE
1793 # Switch Bt878/879 cards into SIS/VIA chipset compatibility mode which is
1794 # needed for some old SiS and VIA chipset motherboards.
1795 # This also allows Bt878/879 chips to work on old OPTi (<1997) chipset
1796 # motherboards and motherboards with bad or incomplete PCI 2.1 support.
1797 # As a rough guess, old = before 1998
1798 #
1799 # options       BKTR_NEW_MSP34XX_DRIVER
1800 # Use new, more complete initialization scheme for the msp34* soundchip.
1801 # Should fix stereo autodetection if the old driver does only output
1802 # mono sound.
1803 #
1804 # options       BKTR_OVERRIDE_CARD=xxx
1805 # options       BKTR_OVERRIDE_DBX=xxx
1806 # options       BKTR_OVERRIDE_MSP=xxx
1807 # options       BKTR_OVERRIDE_TUNER=xxx
1808 # These options can be used to select a specific device, regardless of
1809 # the autodetection and i2c device checks (see comments in bktr_card.c).
1810 #
1811 device          ahc             # AHA2940 and onboard AIC7xxx devices
1812 device          ahd             # AIC79xx devices
1813 device          amd             # AMD 53C974 (Tekram DC-390(T))
1814 device          isp             # Qlogic family
1815 device          ispfw           # Firmware for QLogic HBAs
1816 device          mpt             # LSI '909 FC adapters
1817 device          mps             # LSI-Logic MPT-Fusion 2
1818 device          ncr             # NCR/Symbios Logic
1819 device          sym             # NCR/Symbios Logic (newer chipsets)
1820 device          trm             # Tekram DC395U/UW/F and DC315U
1821 #
1822 # Options for ISP
1823 #
1824 #       ISP_TARGET_MODE         -       enable target mode operation
1825 #options        ISP_TARGET_MODE=1
1826
1827 # Options used in dev/sym/ (Symbios SCSI driver).
1828 #options        SYM_SETUP_LP_PROBE_MAP  #-Low Priority Probe Map (bits)
1829                                         # Allows the ncr to take precedence
1830                                         # 1 (1<<0) -> 810a, 860
1831                                         # 2 (1<<1) -> 825a, 875, 885, 895
1832                                         # 4 (1<<2) -> 895a, 896, 1510d
1833 #options        SYM_SETUP_SCSI_DIFF     #-HVD support for 825a, 875, 885
1834                                         # disabled:0 (default), enabled:1
1835 #options        SYM_SETUP_PCI_PARITY    #-PCI parity checking
1836                                         # disabled:0, enabled:1 (default)
1837 #options        SYM_SETUP_MAX_LUN       #-Number of LUNs supported
1838                                         # default:8, range:[1..64]
1839
1840
1841 # MII bus support is required for some PCI 10/100 ethernet NICs,
1842 # namely those which use MII-compliant transceivers or implement
1843 # transceiver control interfaces that operate like an MII. Adding
1844 # "device miibus0" to the kernel config pulls in support for
1845 # the generic miibus API and all of the PHY drivers, including a
1846 # generic one for PHYs that aren't specifically handled by an
1847 # individual driver.
1848 device          miibus
1849
1850 # PCI Ethernet NICs that use the common MII bus controller code.
1851 device          ae              # Attansic/Atheros L2 Fast Ethernet
1852 device          alc             # Atheros AR8131/AR8132
1853 device          ale             # Atheros AR8121/AR8113/AR8114
1854 device          age             # Attansic/Atheros L1 Gigabit Ethernet
1855 device          bce             # Broadcom NetXtreme II Gigabit Ethernet
1856 device          bfe             # Broadcom BCM440x 10/100 Ethernet
1857 device          dc              # DEC/Intel 21143 and various workalikes
1858 device          fxp             # Intel EtherExpress PRO/100B (82557, 82558)
1859 device          my              # Myson Fast Ethernet (MTD80X, MTD89X)
1860 device          pcn             # AMD Am79C97x PCI 10/100 NICs
1861 device          re              # RealTek 8139C+/8169
1862 device          rl              # RealTek 8129/8139
1863 device          sbsh            # Granch SBNI16 SHDSL modem
1864 device          sf              # Adaptec AIC-6915 (``Starfire'')
1865 device          sis             # Silicon Integrated Systems SiS 900/SiS 7016
1866 device          ste             # Sundance ST201 (D-Link DFE-550TX)
1867 device          tl              # Texas Instruments ThunderLAN
1868 device          tx              # SMC EtherPower II (83c17x ``EPIC'')
1869 device          vge             # VIA 612x GigE
1870 device          vr              # VIA Rhine, Rhine II
1871 device          wb              # Winbond W89C840F
1872 device          xl              # 3Com 3c90x (``Boomerang'', ``Cyclone'')
1873
1874 # PCI Ethernet NICs.
1875 device          de              # DEC/Intel DC21x4x (``Tulip'')
1876 device          txp             # 3Com 3cR990 (``Typhoon'')
1877 device          vx              # 3Com 3c590, 3c595 (``Vortex'')
1878
1879 # Gigabit Ethernet NICs.
1880 device          bge             # Broadcom BCM570x (``Tigon III'')
1881 device          em              # Intel Pro/1000 (8254x,8257x)
1882                                 # Requires ig_hal
1883 device          emx             # Intel Pro/1000 (8257{1,2,3,4})
1884                                 # Requires ig_hal
1885 device          ig_hal          # Intel Pro/1000 hardware abstraction layer
1886 device          et              # Agere ET1310 10/100/1000 Ethernet
1887 device          lge             # Level 1 LXT1001 (``Mercury'')
1888 device          mxge            # Myricom Myri-10G 10GbE NIC
1889 device          nfe             # nVidia nForce2/3 MCP04/51/55 CK804
1890 device          nge             # NatSemi DP83820 and DP83821
1891 device          sk              # SysKonnect GEnesis, LinkSys EG1023, D-Link
1892 device          ti              # Alteon (``Tigon I'', ``Tigon II'')
1893 device          stge            # Sundance/Tamarack TC9021 Gigabit Ethernet
1894 device          msk             # Marvell/SysKonnect Yukon II Gigabit Ethernet
1895 device          jme             # JMicron Gigabit/Fast Ethernet
1896
1897 # Brooktree driver has been ported to the new I2C framework. Thus,
1898 # you'll need to have the following 3 lines in the kernel config.
1899 #     device smbus
1900 #     device iicbus
1901 #     device iicbb
1902 # The iic and smb devices are only needed if you want to control other
1903 # I2C slaves connected to the external connector of some cards.
1904 #
1905 device          bktr
1906 options         BKTR_NEW_MSP34XX_DRIVER
1907
1908 # WinTV PVR-250/350 driver
1909 device          cxm
1910
1911 #
1912 # PCCARD/PCMCIA
1913 #
1914 # pccard: pccard slots
1915 # cardbus/cbb: cardbus bridge
1916 device          pccard
1917 device          cardbus
1918 device          cbb
1919
1920 #
1921 # Laptop/Notebook options:
1922 #
1923 # See also:
1924 #  apm under `Miscellaneous hardware'
1925 # above.
1926
1927 # For older notebooks that signal a powerfail condition (external
1928 # power supply dropped, or battery state low) by issuing an NMI:
1929
1930 options         POWERFAIL_NMI   # make it beep instead of panicing
1931
1932 #
1933 # MMC/SD
1934 #
1935 # mmc           MMC/SD bus
1936 # mmcsd         MMC/SD memory card
1937 # sdhci         Generic PCI SD Host Controller
1938 #
1939 device          mmc
1940 device          mmcsd
1941 device          sdhci
1942
1943 #
1944 # SMB bus
1945 #
1946 # System Management Bus support is provided by the 'smbus' device.
1947 # Access to the SMBus device is via the 'smb' device (/dev/smb*),
1948 # which is a child of the 'smbus' device.
1949 #
1950 # Supported devices:
1951 # smb           standard io through /dev/smb*
1952 #
1953 # Supported SMB interfaces:
1954 # iicsmb        I2C to SMB bridge with any iicbus interface
1955 # bktr          brooktree848 I2C hardware interface
1956 # intpm         Intel PIIX4 (82371AB, 82443MX) Power Management Unit
1957 # alpm          Acer Aladdin-IV/V/Pro2 Power Management Unit
1958 # ichsmb        Intel ICH SMBus controller chips (82801AA, 82801AB, 82801BA)
1959 # viapm         VIA VT82C586B,596,686A and VT8233 SMBus controllers
1960 # amdpm         AMD 756 Power Management Unit
1961 # amdsmb        AMD 8111 SMBus 2.0 Controller
1962 #
1963 device          smbus           # Bus support, required for smb below.
1964
1965 device          intpm
1966 device          alpm
1967 device          ichsmb
1968 device          viapm
1969 device          amdpm
1970 device          amdsmb
1971
1972 device          smb
1973
1974 #
1975 # I2C Bus
1976 #
1977 # Philips i2c bus support is provided by the `iicbus' device.
1978 #
1979 # Supported devices:
1980 # ic    i2c network interface
1981 # iic   i2c standard io
1982 # iicsmb i2c to smb bridge. Allow i2c i/o with smb commands.
1983 #
1984 # Supported interfaces:
1985 # pcf   Philips PCF8584 ISA-bus controller
1986 # bktr  brooktree848 I2C software interface
1987 #
1988 # Other:
1989 # iicbb generic I2C bit-banging code (needed by lpbb, bktr)
1990 #
1991 device          iicbus          # Bus support, required for ic/iic/iicsmb below.
1992 device          iicbb
1993
1994 device          ic
1995 device          iic
1996 device          iicsmb          # smb over i2c bridge
1997
1998 device          pcf0    at isa? port 0x320 irq 5
1999
2000 # Intel Core and newer CPUs on-die digital thermal sensor support
2001 device          coretemp
2002
2003 # AMD Family 0Fh, 10h and 11h temperature sensors
2004 device          kate
2005 device          km
2006
2007 # ThinkPad Active Protection System accelerometer
2008 device          aps0    at isa? port 0x1600
2009
2010 # HW monitoring devices lm(4), it(4) and nsclpcsio.
2011 device          lm0     at isa? port 0x290
2012 device          it0     at isa? port 0x290
2013 device          it1     at isa? port 0xc00
2014 device          it2     at isa? port 0xd00
2015 device          it3     at isa? port 0x228
2016 device          nsclpcsio0 at isa? port 0x2e
2017 device          nsclpcsio1 at isa? port 0x4e
2018 device          wbsio0  at isa? port 0x2e
2019 device          wbsio1  at isa? port 0x4e
2020 device          lm#3    at wbsio?
2021 device          uguru0  at isa? port 0xe0       # ABIT uGuru
2022
2023 # Parallel-Port Bus
2024 #
2025 # Parallel port bus support is provided by the `ppbus' device.
2026 # Multiple devices may be attached to the parallel port, devices
2027 # are automatically probed and attached when found.
2028 #
2029 # Supported devices:
2030 # vpo   Iomega Zip Drive
2031 #       Requires SCSI disk support ('scbus' and 'da'); the best
2032 #       performance is achieved with ports in EPP 1.9 mode.
2033 # lpt   Parallel Printer
2034 # plip  Parallel network interface
2035 # ppi   General-purpose I/O ("Geek Port") + IEEE1284 I/O
2036 # pps   Pulse per second Timing Interface
2037 # lpbb  Philips official parallel port I2C bit-banging interface
2038 #
2039 # Supported interfaces:
2040 # ppc   ISA-bus parallel port interfaces.
2041 #
2042
2043 options         PPC_PROBE_CHIPSET # Enable chipset specific detection
2044                                   # (see flags in ppc(4))
2045 options         DEBUG_1284      # IEEE1284 signaling protocol debug
2046 options         PERIPH_1284     # Makes your computer act as a IEEE1284
2047                                 # compliant peripheral
2048 options         DONTPROBE_1284  # Avoid boot detection of PnP parallel devices
2049 options         VP0_DEBUG       # ZIP/ZIP+ debug
2050 options         LPT_DEBUG       # Printer driver debug
2051 options         PPC_DEBUG=2     # Parallel chipset level debug
2052 options         PLIP_DEBUG      # Parallel network IP interface debug
2053 options         PCFCLOCK_VERBOSE         # Verbose pcfclock driver
2054 options         PCFCLOCK_MAX_RETRIES=5   # Maximum read tries (default 10)
2055
2056 device          ppc0    at isa? irq 7
2057 device          ppbus
2058 device          vpo
2059 device          lpt
2060 device          plip
2061 device          ppi
2062 device          pps
2063 device          lpbb
2064 device          pcfclock
2065
2066 # Kernel BOOTP support
2067
2068 options         BOOTP           # Use BOOTP to obtain IP address/hostname
2069 options         BOOTP_NFSROOT   # NFS mount root filesystem using BOOTP info
2070 options         BOOTP_NFSV3     # Use NFS v3 to NFS mount root
2071 options         BOOTP_COMPAT    # Workaround for broken bootp daemons.
2072 options         BOOTP_WIRED_TO=fxp0 # Use interface fxp0 for BOOTP
2073
2074 #
2075 # Add tie-ins for a hardware watchdog.  This only enable the hooks;
2076 # the user must still supply the actual driver.
2077 #
2078 options         HW_WDOG
2079
2080 #
2081 # Set the number of PV entries per process.  Increasing this can
2082 # stop panics related to heavy use of shared memory. However, that can
2083 # (combined with large amounts of physical memory) cause panics at
2084 # boot time due the kernel running out of VM space.
2085 #
2086 # If you're tweaking this, you might also want to increase the sysctls
2087 # "vm.v_free_min", "vm.v_free_reserved", and "vm.v_free_target".
2088 #
2089 # The value below is the one more than the default.
2090 #
2091 options         PMAP_SHPGPERPROC=201
2092
2093 #
2094 # Change the size of the kernel virtual address space.  Due to
2095 # constraints in loader(8) on i386, this must be a multiple of 4.
2096 # 256 = 1 GB of kernel address space.  Increasing this also causes
2097 # a reduction of the address space in user processes.  512 splits
2098 # the 4GB cpu address space in half (2GB user, 2GB kernel).
2099 #
2100 options         KVA_PAGES=260
2101
2102 #
2103 # Disable swapping. This option removes all code which actually performs
2104 # swapping, so it's not possible to turn it back on at run-time.
2105 #
2106 # This is sometimes usable for systems which don't have any swap space
2107 # (see also sysctls "vm.defer_swapspace_pageouts" and
2108 # "vm.disable_swapspace_pageouts")
2109 #
2110 #options        NO_SWAPPING
2111
2112 # Set the size of the buffer cache KVM reservation, in buffers.  This is
2113 # scaled by approximately 16384 bytes.  The system will auto-size the buffer
2114 # cache if this option is not specified.
2115 #
2116 options         NBUF=512
2117
2118 # Set the size of the mbuf KVM reservation, in clusters.  This is scaled
2119 # by approximately 2048 bytes.  The system will auto-size the mbuf area
2120 # to (512 + maxusers*16) if this option is not specified.
2121 # maxusers is in turn computed at boot time depending on available memory
2122 # or set to the value specified by "options MAXUSERS=x" (x=0 means
2123 # autoscaling).
2124 # So, to take advantage of autoscaling, you have to remove both
2125 # NMBCLUSTERS and MAXUSERS (and NMBUFS) from your kernel config.
2126 #
2127 options         NMBCLUSTERS=1024
2128
2129 # Set the number of mbufs available in the system. Each mbuf
2130 # consumes 256 bytes. The system will autosize this (to 4 times
2131 # the number of NMBCLUSTERS, depending on other constraints)
2132 # if this option is not specified.
2133 #
2134 options         NMBUFS=4096
2135
2136 # Tune the buffer cache maximum KVA reservation, in bytes.  The maximum is
2137 # usually capped at 200 MB, effecting machines with > 1GB of ram.  Note
2138 # that the buffer cache only really governs write buffering and disk block
2139 # translations.  The VM page cache is our primary disk cache and is not
2140 # effected by the size of the buffer cache.
2141 #
2142 options         VM_BCACHE_SIZE_MAX="(100*1024*1024)"
2143
2144 # Tune the swap zone KVA reservation, in bytes.  The default is typically
2145 # 70 MB, giving the system the ability to manage a maximum of 28GB worth
2146 # of swapped out data.
2147 #
2148 options         VM_SWZONE_SIZE_MAX="(50*1024*1024)"
2149
2150 #
2151 # Enable extra debugging code for locks.  This stores the filename and
2152 # line of whatever acquired the lock in the lock itself, and change a
2153 # number of function calls to pass around the relevant data.  This is
2154 # not at all useful unless you are debugging lock code.  Also note
2155 # that it is likely to break e.g. fstat(1) unless you recompile your
2156 # userland with -DDEBUG_LOCKS as well.
2157 #
2158 options         DEBUG_LOCKS
2159
2160 # Set the amount of time (in seconds) the system will wait before
2161 # rebooting automatically when a kernel panic occurs.  If set to (-1),
2162 # the system will wait indefinitely until a key is pressed on the
2163 # console.
2164 options         PANIC_REBOOT_WAIT_TIME=16
2165
2166 # Attempt to bypass the buffer cache and put data directly into the
2167 # userland buffer for read operation when O_DIRECT flag is set on the
2168 # file.  Both offset and length of the read operation must be
2169 # multiples of the physical media sector size.
2170 #
2171 options         DIRECTIO
2172
2173 # Specify a lower limit for the number of swap I/O buffers.  They are
2174 # (among other things) used when bypassing the buffer cache due to
2175 # DIRECTIO kernel option enabled and O_DIRECT flag set on file.
2176 #
2177 #options                NSWBUF_MIN=120
2178
2179 # The 'asr' driver provides support for current DPT/Adaptec SCSI RAID
2180 # controllers (SmartRAID V and VI and later).
2181 # These controllers require the CAM infrastructure.
2182 #
2183 device          asr
2184 options         ASR_COMPAT
2185
2186 # The 'dpt' driver provides support for DPT controllers (http://www.dpt.com/).
2187 # These have hardware RAID-{0,1,5} support, and do multi-initiator I/O.
2188 # The DPT controllers are commonly re-licensed under other brand-names -
2189 # some controllers by Olivetti, Dec, HP, AT&T, SNI, AST, Alphatronic, NEC and
2190 # Compaq are actually DPT controllers.
2191 #
2192 # See src/sys/dev/raid/dpt for debugging and other subtle options.
2193 #   DPT_MEASURE_PERFORMANCE Enables a set of (semi)invasive metrics. Various
2194 #                           instruments are enabled.  The tools in
2195 #                           /usr/sbin/dpt_* assume these to be enabled.
2196 #   DPT_HANDLE_TIMEOUTS     Normally device timeouts are handled by the DPT.
2197 #                           If you ant the driver to handle timeouts, enable
2198 #                           this option.  If your system is very busy, this
2199 #                           option will create more trouble than solve.
2200 #   DPT_TIMEOUT_FACTOR      Used to compute the excessive amount of time to
2201 #                           wait when timing out with the above option.
2202 #  DPT_DEBUG_xxxx           These are controllable from sys/dev/dpt/raid/dpt.h
2203 #  DPT_LOST_IRQ             When enabled, will try, once per second, to catch
2204 #                           any interrupt that got lost.  Seems to help in some
2205 #                           DPT-firmware/Motherboard combinations.  Minimal
2206 #                           cost, great benefit.
2207 #  DPT_RESET_HBA            Make "reset" actually reset the controller
2208 #                           instead of fudging it.  Only enable this if you
2209 #                           are 100% certain you need it.
2210
2211 device          dpt
2212
2213 # DPT options
2214 #!CAM# options  DPT_MEASURE_PERFORMANCE
2215 #!CAM# options  DPT_HANDLE_TIMEOUTS
2216 options         DPT_TIMEOUT_FACTOR=4
2217 options         DPT_LOST_IRQ
2218 options         DPT_RESET_HBA
2219
2220 #
2221 # Compaq "CISS" RAID controllers (SmartRAID 5* series)
2222 # These controllers have a SCSI-like interface, and require the
2223 # CAM infrastructure.
2224 #
2225 device          ciss
2226
2227 #
2228 # Intel Integrated RAID controllers.
2229 # This driver is supported and maintained by
2230 # "Leubner, Achim" <Achim_Leubner@adaptec.com>.
2231 #
2232 device          iir
2233
2234 #
2235 # Mylex AcceleRAID and eXtremeRAID controllers with v6 and later
2236 # firmware.  These controllers have a SCSI-like interface, and require
2237 # the CAM infrastructure.
2238 #
2239 device          mly
2240
2241 # USB support
2242 # UHCI controller
2243 device          uhci
2244 # OHCI controller
2245 device          ohci
2246 # EHCI controller
2247 device          ehci
2248 # General USB code (mandatory for USB)
2249 device          usb
2250 #
2251 # USB Bluetooth
2252 device          ubt
2253 # Fm Radio
2254 device          ufm
2255 # Generic USB device driver
2256 device          ugen
2257 # Human Interface Device (anything with buttons and dials)
2258 device          uhid
2259 # USB keyboard
2260 device          ukbd
2261 # USB printer
2262 device          ulpt
2263 # USB Iomega Zip 100 Drive (Requires scbus and da)
2264 device          umass
2265 # USB modem support
2266 device          umodem
2267 # USB mouse
2268 device          ums
2269 # USB Rio (MP3 Player)
2270 device          urio
2271 # USB scanners
2272 device          uscanner
2273 # USB com devices
2274 device          moscom
2275 device          uark
2276 device          ubsa
2277 device          uchcom
2278 device          ucom
2279 device          uftdi
2280 device          ugensa
2281 device          umct
2282 device          uplcom
2283 device          uslcom
2284 device          uticom
2285 device          uvisor
2286 device          uvscom
2287
2288 #
2289 # ADMtek USB ethernet. Supports the LinkSys USB100TX,
2290 # the Billionton USB100, the Melco LU-ATX, the D-Link DSB-650TX
2291 # and the SMC 2202USB. Also works with the ADMtek AN986 Pegasus
2292 # eval board.
2293 device          aue
2294 #
2295 # ASIX Electronics AX88172 USB 2.0 ethernet driver. Used in the
2296 # LinkSys USB200M and various other adapters.
2297 device          axe
2298 #
2299 # CATC USB-EL1201A USB ethernet. Supports the CATC Netmate
2300 # and Netmate II, and the Belkin F5U111.
2301 device          cue
2302 #
2303 # Kawasaki LSI ethernet. Supports the LinkSys USB10T,
2304 # Entrega USB-NET-E45, Peracom Ethernet Adapter, the
2305 # 3Com 3c19250, the ADS Technologies USB-10BT, the ATen UC10T,
2306 # the Netgear EA101, the D-Link DSB-650, the SMC 2102USB
2307 # and 2104USB, and the Corega USB-T.
2308 device          kue
2309 #
2310 # USB CDC ethernet. Supports the LG P-500 smartphone.
2311 device          lgue
2312 #
2313 # RealTek 8150 based USB ethernet device:
2314 #   Melco LUA-KTX
2315 #   GREEN HOUSE GH-USB100B
2316 #   Billionton ThumbLAN USBKR2-100B
2317 device          rue
2318
2319 # USB wireless NICs, requires wlan_amrr
2320 #
2321 # Ralink Technology RT2501USB/RT2601USB
2322 #device         rum
2323 #
2324 # Ralink Technology RT2500USB
2325 #device         ural
2326
2327 # debugging options for the USB subsystem
2328 #
2329 options         USB_DEBUG
2330
2331 # options for ukbd:
2332 options         UKBD_DFLT_KEYMAP        # specify the built-in keymap
2333 makeoptions     UKBD_DFLT_KEYMAP=it.iso
2334
2335 # Firewire support
2336 device          firewire        # Firewire bus code
2337 device          sbp             # SCSI over Firewire (Requires scbus and da)
2338 device          fwe             # Ethernet over Firewire (non-standard!)
2339
2340 # dcons support (Dumb Console Device)
2341 device          dcons                   # dumb console driver
2342 device          dcons_crom              # FireWire attachment
2343 options         DCONS_BUF_SIZE=16384    # buffer size
2344 options         DCONS_POLL_HZ=100       # polling rate
2345 options         DCONS_FORCE_CONSOLE=1   # force to be the primary console
2346 options         DCONS_FORCE_GDB=1       # force to be the gdb device
2347
2348 #####################################################################
2349 # crypto subsystem
2350 #
2351 # This is a port of the openbsd crypto framework.  Include this when
2352 # configuring IPsec and when you have a h/w crypto device to accelerate
2353 # user applications that link to openssl.
2354 #
2355 # Drivers are ports from openbsd with some simple enhancements that have
2356 # been fed back to openbsd (and hopefully will be included).
2357
2358 pseudo-device   crypto          # core crypto support
2359 pseudo-device   cryptodev       # /dev/crypto for access to h/w
2360
2361 device          rndtest         # FIPS 140-2 entropy tester
2362
2363 device          hifn            # Hifn 7951, 7781, etc.
2364 options         HIFN_DEBUG      # enable debugging support: hw.hifn.debug
2365 #options        HIFN_NO_RNG     # for devices without RNG
2366 options         HIFN_RNDTEST    # enable rndtest support
2367
2368 device          safe            # SafeNet 1141
2369 options         SAFE_DEBUG      # enable debugging support: hw.safe.debug
2370 #options        SAFE_NO_RNG     # for devices without RNG
2371 options         SAFE_RNDTEST    # enable rndtest support
2372
2373 device          ubsec           # Broadcom 5501, 5601, 58xx
2374 options         UBSEC_DEBUG     # enable debugging support: hw.ubsec.debug
2375 #options        UBSEC_NO_RNG    # for devices without RNG
2376 options         UBSEC_RNDTEST   # enable rndtest support
2377
2378 device          aesni           # hardware crypto/RNG for AES-NI
2379 device          glxsb           # Geode LX Security Block
2380 device          padlock         # hardware crypto/RNG for VIA C3/C7/Eden
2381
2382 #
2383 # ACPI support using the Intel ACPI Component Architecture reference
2384 # implementation.
2385 #
2386 # ACPI_DEBUG enables the use of the debug.acpi.level and debug.acpi.layer
2387 # kernel environment variables to select initial debugging levels for the
2388 # Intel ACPICA code.
2389 #
2390 # Note that building ACPI into the kernel is deprecated; the module is
2391 # normally loaded automatically by the loader.
2392
2393 device          acpi
2394 options         ACPI_DEBUG
2395
2396 # ACPI Asus Extras (LCD backlight/brightness, video output, etc.)
2397 device          acpi_asus
2398
2399 # ACPI Fujitsu Extras (Buttons)
2400 device          acpi_fujitsu
2401
2402 # ACPI extras driver for HP laptops
2403 #device         acpi_hp
2404
2405 # ACPI Panasonic Extras (LCD backlight/brightness, video output, etc.)
2406 device          acpi_panasonic
2407
2408 # ACPI Sony extra (LCD brightness)
2409 device          acpi_sony
2410
2411 # ACPI extras driver for ThinkPad laptops
2412 device          acpi_thinkpad
2413
2414 # ACPI Toshiba Extras (LCD backlight/brightness, video output, etc.)
2415 device          acpi_toshiba
2416
2417 # ACPI Video Extensions (LCD backlight/brightness, video output, etc.)
2418 device          acpi_video
2419
2420 device          aibs            # ASUSTeK AI Booster (ACPI ASOC ATK0110)
2421 device          pmtimer         # adjust the system clock after resume
2422
2423 # DRM options:
2424 # drm:          General DRM code
2425 # i915drm:      Intel i830, i845, i915, i945, i965, G33/35
2426 # mach64drm:    ATI Mach64 cards - Rage and 3D Rage series
2427 # mgadrm:       AGP Matrox G200, G400, G450, G550
2428 # r128drm:      ATI Rage 128 cards
2429 # radeondrm:    ATI Radeon cards
2430 # savagedrm:    Savage cards
2431 # sisdrm:       Sis cards
2432 # tdfxdrm:      3dfx Voodoo 3/4/5 and Banshee
2433 #
2434 # DRM_DEBUG:    include debug printfs, very slow
2435 #
2436 # DRM requires AGP in the kernel.
2437
2438 device          drm
2439 device          "i915drm"
2440 device          "mach64drm"
2441 device          mgadrm
2442 device          "r128drm"
2443 device          radeondrm
2444 device          savagedrm
2445 device          sisdrm
2446 device          tdfxdrm
2447
2448 options         DRM_DEBUG
2449 options         DRM_LINUX
2450
2451 #
2452 # Misc devices
2453 #
2454 device          cmx             # Omnikey CardMan 4040 smartcard reader
2455 device          gpio            # Enable support for the gpio framework
2456 device          tbridge         # regression testing
2457
2458 #
2459 # Embedded system options:
2460 #
2461 # An embedded system might want to run something other than init.
2462 options         INIT_PATH="/sbin/init:/sbin/oinit"
2463
2464 # Debug options
2465 options         BUS_DEBUG       # enable newbus debugging
2466 options         NPX_DEBUG       # enable npx debugging (FPU/math emu)
2467 options         RSS_DEBUG       # enable RSS (Receive Side Scaling) debugging
2468
2469 # Record the program counter of the code interrupted by the statistics
2470 # clock interrupt.  Use pctrack(8) to dump this information.
2471 options         DEBUG_PCTRACK
2472
2473 # More undocumented options for linting.
2474 # Note that documenting these are not considered an affront.
2475
2476 #options        ACPI_NO_SEMAPHORES
2477 options         AHC_DUMP_EEPROM
2478 #options        BKTR_ALLOC_PAGES=xxx
2479 options         CAM_DEBUG_DELAY
2480 options         CLUSTERDEBUG
2481 options         COMPAT_LINUX
2482 options         COMPAT_SUNOS
2483 options         DEBUG
2484 options         DEBUG_CRIT_SECTIONS
2485 options         DEBUG_INTERRUPTS
2486 #options        DISABLE_PSE
2487 options         BCE_DEBUG
2488 options         EMX_RSS_DEBUG
2489 options         JME_RSS_DEBUG
2490 #options        ED_NO_MIIBUS
2491 options         ENABLE_ALART
2492 options         FB_DEBUG=2
2493 options         FB_INSTALL_CDEV
2494 options         FE_8BIT_SUPPORT
2495 options         I586_PMC_GUPROF=0x70000
2496 #options        IEEE80211_DEBUG_REFCNT
2497 options         IEEE80211_SUPPORT_SUPERG
2498 options         KBDIO_DEBUG=10
2499 options         KBD_MAXRETRY=4
2500 options         KBD_MAXWAIT=6
2501 options         KBD_RESETDELAY=201
2502 options         KERN_TIMESTAMP
2503 options         KEY
2504 options         LINPROCFS
2505 options         LOCKF_DEBUG
2506 #options        MAXFILES=xxx
2507 options         MBUF_DEBUG
2508 options         PANIC_DEBUG
2509 options         PMAP_DEBUG
2510 options         PSM_DEBUG=4
2511 options         SCSI_NCR_DEBUG
2512 options         SCSI_NCR_MAX_SYNC=10000
2513 options         SCSI_NCR_MAX_WIDE=1
2514 options         SCSI_NCR_MYADDR=7
2515 options         SHOW_BUSYBUFS   # List buffers that prevent root unmount
2516 options         SI_DEBUG
2517 options         SLAB_DEBUG
2518 options         SLIP_IFF_OPTS
2519 options         SOCKBUF_DEBUG
2520 options         TDMA_BINTVAL_DEFAULT=5
2521 options         TDMA_SLOTCNT_DEFAULT=2
2522 options         TDMA_SLOTLEN_DEFAULT=10*1000
2523 options         TDMA_TXRATE_11A_DEFAULT=2*24
2524 options         TDMA_TXRATE_11B_DEFAULT=2*11
2525 options         TDMA_TXRATE_11G_DEFAULT=2*24
2526 options         TDMA_TXRATE_11NA_DEFAULT="(4|IEEE80211_RATE_MCS)"
2527 options         TDMA_TXRATE_11NG_DEFAULT="(4|IEEE80211_RATE_MCS)"
2528 options         TDMA_TXRATE_HALF_DEFAULT=2*12
2529 options         TDMA_TXRATE_QUARTER_DEFAULT=2*6
2530 options         TDMA_TXRATE_TURBO_DEFAULT=2*24
2531 options         TIMER_FREQ="((14318182+6)/12)"
2532 options         VFS_BIO_DEBUG
2533 options         VM_PAGE_DEBUG
2534 options         XBONEHACK
2535
2536 options KTR
2537 options KTR_ALL
2538 options KTR_ENTRIES=1024
2539 options KTR_VERBOSE=1
2540 #options KTR_CTXSW
2541 #options KTR_DMCRYPT
2542 #options KTR_DSCHED_BFQ
2543 #options KTR_ETHERNET
2544 #options KTR_HAMMER
2545 #options KTR_IFQ
2546 #options KTR_IF_BGE
2547 #options KTR_IF_EM
2548 #options KTR_IF_EMX
2549 #options KTR_IF_START
2550 #options KTR_IPIQ
2551 #options KTR_KERNENTRY
2552 #options KTR_MEMORY
2553 #options KTR_POLLING
2554 #options KTR_SERIALIZER
2555 #options KTR_SPIN_CONTENTION
2556 #options KTR_TESTLOG
2557 #options KTR_TOKENS
2558 #options KTR_TSLEEP
2559 #options KTR_USB_MEMORY
2560
2561 # ALTQ
2562 options         ALTQ            #alternate queueing
2563 options         ALTQ_CBQ        #class based queueing
2564 options         ALTQ_RED        #random early detection
2565 options         ALTQ_RIO        #triple red for diffserv (needs RED)
2566 options         ALTQ_HFSC       #hierarchical fair service curve
2567 options         ALTQ_PRIQ       #priority queue
2568 options         ALTQ_FAIRQ      #fair queue
2569 #options        ALTQ_NOPCC      #don't use processor cycle counter
2570 options         ALTQ_DEBUG      #for debugging
2571 # you might want to set kernel timer to 1kHz if you use CBQ,
2572 # especially with 100baseT
2573 #options        HZ=1000
2574
2575 # SCTP
2576 options         SCTP
2577 options         SCTP_DEBUG
2578 options         SCTP_USE_ADLER32
2579 options         SCTP_HIGH_SPEED
2580 options         SCTP_STAT_LOGGING
2581 options         SCTP_CWND_LOGGING
2582 options         SCTP_BLK_LOGGING
2583 options         SCTP_STR_LOGGING
2584 options         SCTP_FR_LOGGING
2585 options         SCTP_MAP_LOGGING
2586
2587 # DSCHED stuff
2588 options         DSCHED_FQ
2589 options         DSCHED_BFQ
2590
2591 # WATCHDOG
2592 options         WATCHDOG_ENABLE         # Enable watchdog support framework
2593 options         WDOG_DISABLE_ON_PANIC   # Automatically disable watchdogs on panic
2594
2595 # LED
2596 options         ERROR_LED_ON_PANIC      # If an error led is present, light it up on panic