build: Add ICMPPRINTFS as global option
[dragonfly.git] / sys / config / LINT64
CommitLineData
745b8439
SW
1#
2# X86_64_LINT -- config file for checking all the sources, tries to pull in
3# as much of the source tree as it can.
4#
5# $FreeBSD: src/sys/i386/conf/LINT,v 1.749.2.144 2003/06/04 17:56:59 sam Exp $
6#
7# See the kernconf(5) manual page for more information on the format of
8# this file.
9#
10# NB: You probably don't want to try running a kernel built from this
11# file. Instead, you should start from X86_64_GENERIC, and add options
12# from this file as required.
13#
14
15# These directives are mandatory. The machine directive specifies the
16# platform and the machine_arch directive specifies the cpu architecture.
17#
18platform pc64
19machine x86_64
20machine_arch x86_64
21
22#
23# This is the ``identification'' of the kernel. Usually this should
24# be the same as the name of your kernel.
25#
26ident X86_64_LINT
27
28#
29# The `maxusers' parameter controls the static sizing of a number of
30# internal system tables by a formula defined in subr_param.c. Setting
31# maxusers to 0 will cause the system to auto-size based on physical
32# memory.
33#
34maxusers 10
35
36#
37# The `makeoptions' parameter allows variables to be passed to the
38# generated Makefile in the build area.
39#
40# CONF_CFLAGS gives some extra compiler flags that are added to ${CFLAGS}
41# after most other flags. Here we use it to inhibit use of non-optimal
42# gcc builtin functions (e.g., memcmp).
43#
44# DEBUG happens to be magic.
45# The following is equivalent to 'config -g KERNELNAME' and creates
46# 'kernel.debug' compiled with -g debugging as well as a normal
47# 'kernel'. Use 'make install.debug' to install the debug kernel
48# but that isn't normally necessary as the debug symbols are not loaded
49# by the kernel and are not useful there anyway.
50#
51# KERNEL can be overridden so that you can change the default name of your
52# kernel.
53#
54# MODULES_OVERRIDE can be used to limit modules built to a specific list.
55#
56# INSTALLSTRIPPED can be set to cause installkernel to install stripped
57# kernels and modules rather than a kernel and modules with debug symbols.
58#
59# INSTALLSTRIPPEDMODULES can be set to allow a full debug kernel to be
60# installed, but to strip the installed modules.
61#
62makeoptions CONF_CFLAGS=-fno-builtin #Don't allow use of memcmp, etc.
63#makeoptions DEBUG=-g #Build kernel with gdb(1) debug symbols
64#makeoptions KERNEL=foo #Build kernel "foo" and install "/foo"
65# Only build Linux API modules and plus those parts of the sound system I need.
66#makeoptions MODULES_OVERRIDE="linux sound/snd sound/pcm sound/driver/maestro3"
67#makeoptions INSTALLSTRIPPED=1
68#makeoptions INSTALLSTRIPPEDMODULES=1
69
70#
71# Certain applications can grow to be larger than the 128M limit
72# that DragonFly initially imposes. Below are some options to
73# allow that limit to grow to 256MB, and can be increased further
74# with changing the parameters. MAXDSIZ is the maximum that the
75# limit can be set to, and the DFLDSIZ is the default value for
76# the limit. MAXSSIZ is the maximum that the stack limit can be
77# set to. You might want to set the default lower than the max,
78# and explicitly set the maximum with a shell command for processes
79# that regularly exceed the limit like INND.
80#
81options MAXDSIZ="(256*1024*1024)"
82options MAXSSIZ="(256*1024*1024)"
83options DFLDSIZ="(256*1024*1024)"
84
85#
86# BLKDEV_IOSIZE sets the default block size used in user block
87# device I/O. Note that this value will be overridden by the label
88# when specifying a block device from a label with a non-0
89# partition blocksize. The default is PAGE_SIZE.
90#
91options BLKDEV_IOSIZE=8192
92
745b8439
SW
93# This allows you to actually store this configuration file into
94# the kernel binary itself, where it may be later read by saying:
95# strings -n 3 /kernel | sed -n 's/^___//p' > MYKERNEL
96#
97options INCLUDE_CONFIG_FILE # Include this file in kernel
98
99#
100# The root device and filesystem type can be compiled in;
101# this provides a fallback option if the root device cannot
102# be correctly guessed by the bootstrap code, or an override if
103# the RB_DFLTROOT flag (-r) is specified when booting the kernel.
104#
105options ROOTDEVNAME=\"ufs:da0s2e\"
106
745b8439
SW
107#####################################################################
108# CPU OPTIONS
109
110cpu HAMMER_CPU
111
112#
113# Options for CPU features.
114#
dbe005bb
SW
115# CPU_ENABLE_EST enables support for Enhanced SpeedStep technology
116# found in Pentium(tm) M processors.
117#
5cf56a8d
AH
118# CPU_DISABLE_AVX disables AVX instruction set.
119#
5cf56a8d 120options CPU_DISABLE_AVX
dbe005bb 121options CPU_ENABLE_EST
ebea24c3 122
745b8439
SW
123#####################################################################
124# COMPATIBILITY OPTIONS
125
126#
127# Implement system calls compatible with 4.3BSD and older versions of
128# FreeBSD. You probably do NOT want to remove this as much current code
129# still relies on the 4.3 emulation.
130#
131options COMPAT_43
132
efba76b4
SW
133# Enable NDIS binary driver support
134options NDISAPI
135device ndis
136
745b8439
SW
137#
138# These three options provide support for System V Interface
139# Definition-style interprocess communication, in the form of shared
140# memory, semaphores, and message queues, respectively.
141#
142# System V shared memory and tunable parameters
745b8439
SW
143options SHMMIN=2 # min shared memory segment size (bytes)
144options SHMMNI=33 # max number of shared memory identifiers
145options SHMSEG=9 # max shared memory segments per process
146
147# System V semaphores and tunable parameters
745b8439
SW
148options SEMMAP=31 # amount of entries in semaphore map
149options SEMMNI=11 # number of semaphore identifiers in the system
150options SEMMNS=61 # number of semaphores in the system
151options SEMMNU=31 # number of undo structures in the system
152options SEMMSL=61 # max number of semaphores per id
153options SEMOPM=101 # max number of operations per semop call
154options SEMUME=11 # max number of undo entries per process
155
156# System V message queues and tunable parameters
745b8439
SW
157options MSGMNB=2049 # max characters per message queue
158options MSGMNI=41 # max number of message queue identifiers
159options MSGSEG=2049 # max number of message segments in the system
160options MSGSSZ=16 # size of a message segment MUST be power of 2
161options MSGTQL=41 # max amount of messages in the system
162
745b8439
SW
163#####################################################################
164# DEBUGGING OPTIONS
165
166#
167# Enable the kernel debugger.
168#
169options DDB
170
171#
172# Print a stack trace on kernel panic.
173#
174options DDB_TRACE
175
176#
177# Don't drop into DDB for a panic. Intended for unattended operation
178# where you may want to drop to DDB from the console, but still want
179# the machine to recover from a panic
180#
181options DDB_UNATTENDED
182
183#
184# If using GDB remote mode to debug the kernel, there's a non-standard
185# extension to the remote protocol that can be used to use the serial
186# port as both the debugging port and the system console. It's non-
187# standard and you're on your own if you enable it. See also the
188# "remotechat" variables in the DragonFly specific version of gdb.
189#
190options GDB_REMOTE_CHAT
191
192#
193# KTRACE enables the system-call tracing facility ktrace(2).
194#
195options KTRACE #kernel tracing
196
197#
198# The INVARIANTS option is used in a number of source files to enable
199# extra sanity checking of internal structures. This support is not
200# enabled by default because of the extra time it would take to check
201# for these conditions, which can only occur as a result of
202# programming errors.
203#
204options INVARIANTS
205
206#
207# The DIAGNOSTIC option is used to enable extra debugging information
208# from some parts of the kernel. As this makes everything more noisy,
209# it is disabled by default.
210#
211options DIAGNOSTIC
212
213#
214# PERFMON causes the driver for Pentium/Pentium Pro performance counters
215# to be compiled. See perfmon(4) for more information.
216#
217options PERFMON
218
219
220#
221# This option let some drivers co-exist that can't co-exist in a running
222# system. This is used to be able to compile all kernel code in one go for
223# quality assurance purposes (like this file, which the option takes it name
224# from.)
225#
226options COMPILING_LINT
227
228
229# XXX - this doesn't belong here.
230# Allow ordinary users to take the console - this is useful for X.
231options UCONSOLE
232
745b8439
SW
233#####################################################################
234# NETWORKING OPTIONS
235
236#
237# Protocol families:
238# Only the INET (Internet) family is officially supported in DragonFly.
239# Source code for the NS (Xerox Network Service) is provided for amusement
240# value.
241#
242options INET #Internet communications protocols
243options INET6 #IPv6 communications protocols
244options IPSEC #IP security
245options IPSEC_ESP #IP security (crypto; define w/ IPSEC)
246options IPSEC_DEBUG #debug for IP security
247#
248# Set IPSEC_FILTERGIF to force packets coming through a gif tunnel
d912a10e 249# to be processed by any configured packet filtering (ipfw).
745b8439
SW
250# The default is that packets coming from a tunnel are _not_ processed;
251# they are assumed trusted.
252#
253# Note that enabling this can be problematic as there are no mechanisms
254# in place for distinguishing packets coming out of a tunnel (e.g. no
255# encX devices as found on openbsd).
256#
257#options IPSEC_FILTERGIF #filter ipsec packets from a tunnel
258
259#
260# Experimental IPsec implementation that uses the kernel crypto
261# framework. This cannot be configured together with IPSEC and
262# (currently) supports only IPv4. To use this you must also
263# configure the crypto device (see below). Note that with this
264# you get all the IPsec protocols (e.g. there is no FAST_IPSEC_ESP).
265# IPSEC_DEBUG is used, as above, to configure debugging support
266# within the IPsec protocols.
267#
268#options FAST_IPSEC #new IPsec
269
745b8439
SW
270options MPLS #Multi-Protocol Label Switching
271
7902ca8c
SW
272#
273# SMB/CIFS requester
274# NETSMB enables support for SMB protocol, it requires LIBMCHAIN and LIBICONV
275# options.
276# NETSMBCRYPTO enables support for encrypted passwords.
277options NETSMB #SMB/CIFS requester
278options NETSMBCRYPTO #encrypted password support for SMB
279
745b8439
SW
280# mchain library. It can be either loaded as KLD or compiled into kernel
281options LIBMCHAIN #mbuf management library
282
283# netgraph(4). Enable the base netgraph code with the NETGRAPH option.
284# Individual node types can be enabled with the corresponding option
285# listed below; however, this is not strictly necessary as netgraph
286# will automatically load the corresponding KLD module if the node type
287# is not already compiled into the kernel. Each type below has a
288# corresponding man page, e.g., ng_async(4).
289options NETGRAPH #netgraph(4) system
290options NETGRAPH_ASYNC
291options NETGRAPH_BPF
292options NETGRAPH_BRIDGE
293options NETGRAPH_CISCO
294options NETGRAPH_ECHO
295options NETGRAPH_EIFACE
296options NETGRAPH_ETHER
e288257e 297options NETGRAPH_FEC
745b8439
SW
298options NETGRAPH_FRAME_RELAY
299options NETGRAPH_HOLE
300options NETGRAPH_IFACE
301options NETGRAPH_KSOCKET
302options NETGRAPH_L2TP
303options NETGRAPH_LMI
304# MPPC compression requires proprietary files (not included)
305#options NETGRAPH_MPPC_COMPRESSION
306options NETGRAPH_MPPC_ENCRYPTION
307options NETGRAPH_ONE2MANY
308options NETGRAPH_PPP
309options NETGRAPH_PPPOE
310options NETGRAPH_PPTPGRE
311options NETGRAPH_RFC1490
312options NETGRAPH_SOCKET
313options NETGRAPH_TEE
314options NETGRAPH_TTY
315options NETGRAPH_UI
316options NETGRAPH_VJC
317
318device mn # Munich32x/Falc54 Nx64kbit/sec cards.
319
320#
321# Network interfaces:
322# The `loop' pseudo-device is MANDATORY when networking is enabled.
323# The `ether' pseudo-device provides generic code to handle
324# Ethernets; it is MANDATORY when a Ethernet device driver is
325# configured.
326# The `sppp' pseudo-device serves a similar role for certain types
327# of synchronous PPP links (like `ar').
328# The `sl' pseudo-device implements the Serial Line IP (SLIP) service.
329# The `ppp' pseudo-device implements the Point-to-Point Protocol.
330# The `bpf' pseudo-device enables the Berkeley Packet Filter. Be
331# aware of the legal and administrative consequences of enabling this
332# option. The number of devices determines the maximum number of
333# simultaneous BPF clients programs runnable.
334# The `disc' pseudo-device implements a minimal network interface,
335# which throws away all packets sent and never receives any. It is
336# included for testing purposes. This shows up as the 'ds' interface.
337# The `tun' pseudo-device implements (user-)ppp and nos-tun
338# The `gif' pseudo-device implements IPv6 over IP4 tunneling,
339# IPv4 over IPv6 tunneling, IPv4 over IPv4 tunneling and
340# IPv6 over IPv6 tunneling.
341# The `gre' device implements two types of IP4 over IP4 tunneling:
342# GRE and MOBILE, as specified in the RFC1701 and RFC2004.
343# The `faith' pseudo-device captures packets sent to it and diverts them
344# to the IPv4/IPv6 translation daemon.
345# The `stf' device implements 6to4 encapsulation.
346# The `ef' pseudo-device provides support for multiple ethernet frame types
347# specified via ETHER_* options. See ef(4) for details.
348#
349# The PPP_BSDCOMP option enables support for compress(1) style entire
350# packet compression, the PPP_DEFLATE is for zlib/gzip style compression.
351# PPP_FILTER enables code for filtering the ppp data stream and selecting
352# events for resetting the demand dial activity timer - requires bpf.
353# See pppd(8) for more details.
354#
355pseudo-device ether #Generic Ethernet
356pseudo-device vlan 1 #VLAN support
357pseudo-device bridge #Bridging support
358pseudo-device sppp #Generic Synchronous PPP
359pseudo-device loop #Network loopback device
360pseudo-device bpf #Berkeley packet filter
361pseudo-device disc #Discard device (ds0, ds1, etc)
ded7543c 362pseudo-device tap #Ethernet tunnel network interface
745b8439
SW
363pseudo-device tun #Tunnel driver (ppp(8), nos-tun(8))
364pseudo-device sl 2 #Serial Line IP
365pseudo-device gre #IP over IP tunneling
366pseudo-device ppp 2 #Point-to-point protocol
367options PPP_BSDCOMP #PPP BSD-compress support
368options PPP_DEFLATE #PPP zlib/deflate/gzip support
369options PPP_FILTER #enable bpf filtering (needs bpf)
370
745b8439
SW
371# for IPv6
372pseudo-device gif #IPv6 and IPv4 tunneling
373pseudo-device faith 1 #for IPv6 and IPv4 translation
374pseudo-device stf #6to4 IPv6 over IPv4 encapsulation
375
376#
377# Internet family options:
378#
379# MROUTING enables the kernel multicast packet forwarder, which works
380# with mrouted(8).
381#
382# PIM enables Protocol Independent Multicast in the kernel.
383# Requires MROUTING enabled.
384#
385# IPFIREWALL enables support for IP firewall construction, in
386# conjunction with the `ipfw' program. IPFIREWALL_VERBOSE sends
387# logged packets to the system logger. IPFIREWALL_VERBOSE_LIMIT
388# limits the number of times a matching entry can be logged.
389#
390# WARNING: IPFIREWALL defaults to a policy of "deny ip from any to any"
391# and if you do not add other rules during startup to allow access,
392# YOU WILL LOCK YOURSELF OUT. It is suggested that you set firewall_type=open
393# in /etc/rc.conf when first enabling this feature, then refining the
394# firewall rules in /etc/rc.firewall after you've tested that the new kernel
395# feature works properly.
396#
397# IPFIREWALL_DEFAULT_TO_ACCEPT causes the default rule (at boot) to
398# allow everything. Use with care, if a cracker can crash your
399# firewall machine, they can get to your protected machines. However,
400# if you are using it as an as-needed filter for specific problems as
401# they arise, then this may be for you. Changing the default to 'allow'
402# means that you won't get stuck if the kernel and /sbin/ipfw binary get
403# out of sync.
404#
405# IPDIVERT enables the divert IP sockets, used by ``ipfw divert''
406#
407# IPSTEALTH enables code to support stealth forwarding (i.e., forwarding
408# packets without touching the ttl). This can be useful to hide firewalls
409# from traceroute and similar tools.
410#
411# TCPDEBUG is undocumented.
412#
6bedbebc
SZ
413# ICMPPRINTFS enables ICMP to do extra debug prints.
414#
745b8439
SW
415options MROUTING # Multicast routing
416options PIM # Protocol Independent Multicast
417options IPFIREWALL #firewall
418options IPFIREWALL_DEBUG #debug prints
419options IPFIREWALL_VERBOSE #enable logging to syslogd(8)
745b8439
SW
420options IPFIREWALL_VERBOSE_LIMIT=100 #limit verbosity
421options IPFIREWALL_DEFAULT_TO_ACCEPT #allow everything by default
422options IPV6FIREWALL #firewall for IPv6
423options IPV6FIREWALL_VERBOSE
424options IPV6FIREWALL_VERBOSE_LIMIT=100
425options IPV6FIREWALL_DEFAULT_TO_ACCEPT
426options IPDIVERT #divert sockets
745b8439
SW
427options IPSTEALTH #support for stealth forwarding
428options TCPDEBUG
6bedbebc 429options ICMPPRINTFS
745b8439
SW
430
431device pf
432device pflog
433
434#CARP
435pseudo-device carp
436options CARP
437
438# The MBUF_STRESS_TEST option enables options which create
439# various random failures / extreme cases related to mbuf
440# functions. See the mbuf(9) manpage for a list of available
441# test cases.
442options MBUF_STRESS_TEST
443
444# Statically link in accept filters
445options ACCEPT_FILTER_DATA
446options ACCEPT_FILTER_HTTP
447
448# TCP_SIGNATURE adds support for RFC 2385 (TCP-MD5) digests. These are
449# carried in TCP option 19. This option is commonly used to protect
450# TCP sessions (e.g. BGP) where IPSEC is not available nor desirable.
0defa1cf
SZ
451# This is enabled on a per-socket basis using the TCP_SIGNATURE_ENABLE
452# socket option.
745b8439
SW
453# This requires the use of 'device crypto', 'options IPSEC'
454# or 'device cryptodev'.
455options TCP_SIGNATURE #include support for RFC 2385
456
457#
458# TCP_DROP_SYNFIN adds support for ignoring TCP packets with SYN+FIN. This
459# prevents nmap et al. from identifying the TCP/IP stack, but breaks support
460# for RFC1644 extensions and is not recommended for web servers.
461#
462options TCP_DROP_SYNFIN #drop TCP packets with SYN+FIN
463
464# ICMP_BANDLIM enables icmp error response bandwidth limiting. You
465# typically want this option as it will help protect the machine from
466# D.O.S. packet attacks.
467#
468options ICMP_BANDLIM
469
470# DUMMYNET enables the "dummynet" bandwidth limiter. You need
471# IPFIREWALL as well. See the dummynet(4) and ipfw(8) manpages for more info.
472#
473options DUMMYNET
474options DUMMYNET_DEBUG
475
239ba22e 476# IFPOLL_ENABLE adds support for mixed interrupt-polling handling
745b8439
SW
477# of network device drivers, which has significant benefits in terms
478# of robustness to overloads and responsivity, as well as permitting
479# accurate scheduling of the CPU time between kernel network processing
480# and other activities. The drawback is a moderate (up to 1/pollhz seconds)
481# potential increase in response times. See polling(4) for further details.
482#
745b8439
SW
483# IFPOLL_ENABLE adds hardware queues' based polling
484options IFPOLL_ENABLE
485
745b8439
SW
486#####################################################################
487# FILESYSTEM OPTIONS
488
489#
490# Only the root, /usr, and /tmp filesystems need be statically
491# compiled; everything else will be automatically loaded at mount
492# time. (Exception: the UFS family --- FFS, and MFS ---
493# cannot currently be demand-loaded.) Some people still prefer
494# to statically compile other filesystems as well.
495#
496# NB: The PORTAL and UNION filesystems are known to be
497# buggy, and WILL panic your system if you attempt to do anything with
498# them. They are included here as an incentive for some enterprising
499# soul to sit down and fix them.
500#
501
502# One of these is mandatory:
503options FFS #Fast filesystem
504options MFS #Memory filesystem
505options NFS #Network filesystem
506
507# The rest are optional:
508#options NFS_NOSERVER #Disable the NFS-server code.
509options CD9660 #ISO 9660 filesystem
510options FDESC #File descriptor filesystem
8124268f 511options HAMMER #HAMMER filesystem
745b8439
SW
512options HPFS #OS/2 File system
513options MSDOSFS #MS DOS filesystem
514options NTFS #NT filesystem
515options NULLFS #NULL filesystem
745b8439
SW
516options PORTAL #Portal filesystem
517options PROCFS #Process filesystem
ab5617b3 518options PUFFS #Userspace file systems (e.g. ntfs-3g & sshfs)
7902ca8c 519options SMBFS #SMB/CIFS filesystem
745b8439 520options TMPFS #Temporary filesystem
8124268f 521options UDF #UDF filesystem
745b8439
SW
522
523# YYY-DR Till we rework the VOP methods for this filesystem
524#options UNION #Union filesystem
525# The xFS_ROOT options REQUIRE the associated ``options xFS''
526options FFS_ROOT #FFS usable as root device
527options NFS_ROOT #NFS usable as root device
528
529# Soft updates is technique for improving UFS filesystem speed and
530# making abrupt shutdown less risky.
531options SOFTUPDATES
532
533# Directory hashing improves the speed of operations on very large
534# directories at the expense of some memory.
535options UFS_DIRHASH
536
537# Make space in the kernel for a root filesystem on a md device.
538# Define to the number of kilobytes to reserve for the filesystem.
539options MD_ROOT_SIZE=10
540
541# Make the md device a potential root device, either with preloaded
542# images of type mfs_root or md_root.
543options MD_ROOT
544
545# Specify double the default maximum size for malloc(9)-backed md devices.
546options MD_NSECT=40000
547
548# Allow this many swap-devices.
549#
550# In order to manage swap, the system must reserve bitmap space that
551# scales with the largest mounted swap device multiplied by NSWAPDEV,
552# regardless of whether other swap devices exist or not. So it
553# is not a good idea to make this value too large.
554options NSWAPDEV=5
555
556# Disk quotas are supported when this option is enabled.
557options QUOTA #enable disk quotas
558
559# If you are running a machine just as a fileserver for PC and MAC
d22a69a4 560# users, e.g. using SAMBA, you may consider setting this option
745b8439
SW
561# and keeping all those users' directories on a filesystem that is
562# mounted with the suiddir option. This gives new files the same
563# ownership as the directory (similar to group). It's a security hole
564# if you let these users run programs, so confine it to file-servers
565# (but it'll save you lots of headaches in those cases). Root owned
566# directories are exempt and X bits are cleared. The suid bit must be
567# set on the directory as well; see chmod(1) PC owners can't see/set
568# ownerships so they keep getting their toes trodden on. This saves
569# you all the support calls as the filesystem it's used on will act as
570# they expect: "It's my dir so it must be my file".
571#
572options SUIDDIR
573
574# NFS options:
575options NFS_MINATTRTIMO=3 # VREG attrib cache timeout in sec
576options NFS_MAXATTRTIMO=60
577options NFS_MINDIRATTRTIMO=30 # VDIR attrib cache timeout in sec
578options NFS_MAXDIRATTRTIMO=60
579options NFS_GATHERDELAY=10 # Default write gather delay (msec)
580options NFS_UIDHASHSIZ=29 # Tune the size of nfssvc_sock with this
581options NFS_WDELAYHASHSIZ=16 # and with this
582options NFS_MUIDHASHSIZ=63 # Tune the size of nfsmount with this
583options NFS_DEBUG # Enable NFS Debugging
584
1b0988d0
AHJ
585# NTFS options:
586options NTFS_DEBUG
587
745b8439
SW
588# MSDOSFS options:
589options MSDOSFS_DEBUG # Enable MSDOSFS Debugging
590
591#
592# Add support for the EXT2FS filesystem of Linux fame. Be a bit
593# careful with this - the ext2fs code has a tendency to lag behind
594# changes and not be exercised very much, so mounting read/write could
595# be dangerous (and even mounting read only could result in panics.)
596#
597options EXT2FS
598
599# Optional character code conversion support with LIBICONV.
600# Each option requires their base file system and LIBICONV.
601options CD9660_ICONV
602options MSDOSFS_ICONV
603options NTFS_ICONV
604
745b8439
SW
605#####################################################################
606# POSIX P1003.1B
607
608# Real time extensions added in the 1993 Posix
609# P1003_1B: Infrastructure
610# _KPOSIX_PRIORITY_SCHEDULING: Build in _POSIX_PRIORITY_SCHEDULING
611# _KPOSIX_VERSION: Version kernel is built for
612
613options P1003_1B
614options _KPOSIX_PRIORITY_SCHEDULING
615options _KPOSIX_VERSION=199309L
616
745b8439
SW
617#####################################################################
618# CLOCK OPTIONS
619
620# The granularity of operation is controlled by the kernel option HZ whose
621# default value (100) means a granularity of 10ms (1s/HZ).
622# Consider, however, that reducing the granularity too much might
623# cause excessive overhead in clock interrupt processing,
624# potentially causing ticks to be missed and thus actually reducing
625# the accuracy of operation.
626
627options HZ=100
628
629# The following options are used for debugging clock behavior only, and
630# should not be used for production systems.
631#
632# CLK_CALIBRATION_LOOP will run the clock calibration loop at startup
633# until the user presses a key.
634
635#options CLK_CALIBRATION_LOOP
636
637# The following two options measure the frequency of the corresponding
638# clock relative to the RTC (onboard mc146818a).
639
640#options CLK_USE_I8254_CALIBRATION
641#options CLK_USE_TSC_CALIBRATION
642
745b8439
SW
643#####################################################################
644# SCSI DEVICES
645
646# SCSI DEVICE CONFIGURATION
647
648# The SCSI subsystem consists of the `base' SCSI code, a number of
649# high-level SCSI device `type' drivers, and the low-level host-adapter
650# device drivers. The host adapters are listed in the ISA and PCI
651# device configuration sections below.
652#
653# Beginning with FreeBSD 2.0.5 you can wire down your SCSI devices so
654# that a given bus, target, and LUN always come on line as the same
655# device unit. In earlier versions the unit numbers were assigned
656# in the order that the devices were probed on the SCSI bus. This
657# means that if you removed a disk drive, you may have had to rewrite
658# your /etc/fstab file, and also that you had to be careful when adding
659# a new disk as it may have been probed earlier and moved your device
660# configuration around.
661
662# This old behavior is maintained as the default behavior. The unit
663# assignment begins with the first non-wired down unit for a device
664# type. For example, if you wire a disk as "da3" then the first
665# non-wired disk will be assigned da4.
666
667# The syntax for wiring down devices is:
668
669# device scbus0 at ahc0 # Single bus device
670# device scbus1 at ahc1 bus 0 # Single bus device
671# device scbus3 at ahc2 bus 0 # Twin bus device
672# device scbus2 at ahc2 bus 1 # Twin bus device
673# device da0 at scbus0 target 0 unit 0
674# device da1 at scbus3 target 1
675# device da2 at scbus2 target 3
676# device sa1 at scbus1 target 6
677# device cd
678
679# "units" (SCSI logical unit number) that are not specified are
680# treated as if specified as LUN 0.
681
682# All SCSI devices allocate as many units as are required.
683
684# The "unknown" device (uk? in pre-2.0.5) is now part of the base SCSI
685# configuration and doesn't have to be explicitly configured.
686
687device scbus #base SCSI code
688device ch #SCSI media changers
689device da #SCSI direct access devices (aka disks)
690device sa #SCSI tapes
691device cd #SCSI CD-ROMs
692device pass #CAM passthrough driver
693device sg #Passthrough device (linux scsi generic)
694device pt #SCSI processor type
695device ses #SCSI SES/SAF-TE driver
9c86eff7
SW
696device targ #SCSI Target Mode Code
697device targbh #SCSI Target Mode Blackhole Device
745b8439
SW
698
699# Options for device mapper
700device dm
701device dm_target_crypt
702device dm_target_linear
703device dm_target_striped
704
705# Options for iSCSI
706device iscsi_initiator
707options ISCSI_INITIATOR_DEBUG=8
708
709# CAM OPTIONS:
710# debugging options:
711# -- NOTE -- If you specify one of the bus/target/lun options, you must
712# specify them all!
713# CAMDEBUG: When defined enables debugging macros
714# CAM_DEBUG_BUS: Debug the given bus. Use -1 to debug all busses.
715# CAM_DEBUG_TARGET: Debug the given target. Use -1 to debug all targets.
716# CAM_DEBUG_LUN: Debug the given lun. Use -1 to debug all luns.
717# CAM_DEBUG_FLAGS: OR together CAM_DEBUG_INFO, CAM_DEBUG_TRACE,
718# CAM_DEBUG_SUBTRACE, and CAM_DEBUG_CDB
719#
720# CAM_MAX_HIGHPOWER: Maximum number of concurrent high power (start unit) cmds
721# SCSI_NO_SENSE_STRINGS: When defined disables sense descriptions
722# SCSI_NO_OP_STRINGS: When defined disables opcode descriptions
723# SCSI_DELAY: The number of MILLISECONDS to freeze the SIM (scsi adapter)
724# queue after a bus reset, and the number of milliseconds to
725# freeze the device queue after a bus device reset. This
726# can be changed at boot and runtime with the
727# kern.cam.scsi_delay tunable/sysctl.
728options CAMDEBUG
729options CAM_DEBUG_BUS=-1
730options CAM_DEBUG_TARGET=-1
731options CAM_DEBUG_LUN=-1
732options CAM_DEBUG_FLAGS="CAM_DEBUG_INFO|CAM_DEBUG_TRACE|CAM_DEBUG_CDB"
733options CAM_MAX_HIGHPOWER=4
734options SCSI_NO_SENSE_STRINGS
735options SCSI_NO_OP_STRINGS
736options SCSI_DELAY=8000 # Be pessimistic about Joe SCSI device
737
738# Options for the CAM CDROM driver:
739# CHANGER_MIN_BUSY_SECONDS: Guaranteed minimum time quantum for a changer LUN
740# CHANGER_MAX_BUSY_SECONDS: Maximum time quantum per changer LUN, only
741# enforced if there is I/O waiting for another LUN
742# The compiled in defaults for these variables are 2 and 10 seconds,
743# respectively.
744#
745# These can also be changed on the fly with the following sysctl variables:
746# kern.cam.cd.changer.min_busy_seconds
747# kern.cam.cd.changer.max_busy_seconds
748#
749options CHANGER_MIN_BUSY_SECONDS=2
750options CHANGER_MAX_BUSY_SECONDS=10
751
752# Options for the CAM sequential access driver:
753# SA_IO_TIMEOUT: Timeout for read/write/wfm operations, in minutes
754# SA_SPACE_TIMEOUT: Timeout for space operations, in minutes
755# SA_REWIND_TIMEOUT: Timeout for rewind operations, in minutes
756# SA_ERASE_TIMEOUT: Timeout for erase operations, in minutes
757# SA_1FM_AT_EOD: Default to model which only has a default one filemark at EOT.
758options SA_IO_TIMEOUT="(4)"
759options SA_SPACE_TIMEOUT="(60)"
760options SA_REWIND_TIMEOUT="(2*60)"
761options SA_ERASE_TIMEOUT="(4*60)"
762options SA_1FM_AT_EOD
763
764# Optional timeout for the CAM processor target (pt) device
765# This is specified in seconds. The default is 60 seconds.
766options SCSI_PT_DEFAULT_TIMEOUT="60"
767
768# Optional enable of doing SES passthrough on other devices (e.g., disks)
769#
770# Normally disabled because a lot of newer SCSI disks report themselves
771# as having SES capabilities, but this can then clot up attempts to build
772# build a topology with the SES device that's on the box these drives
773# are in....
774options SES_ENABLE_PASSTHROUGH
775
745b8439
SW
776#####################################################################
777# MISCELLANEOUS DEVICES AND OPTIONS
778
779# The `pty' device usually turns out to be ``effectively mandatory'',
780# as it is required for `telnetd', `rlogind', `screen', `emacs', and
781# `xterm', among others.
782
b8afae86
MD
783pseudo-device pty # Pseudo ttys
784pseudo-device gzip # Exec gzipped a.out's
785pseudo-device md # Memory/malloc disk
786pseudo-device vn # File image "disks"
787pseudo-device putter # for puffs and pud
788pseudo-device snp # Snoop device - to look at pty/vty/etc..
789pseudo-device ccd 4 # Concatenated disk driver
745b8439
SW
790
791# Configuring Vinum into the kernel is not necessary, since the kld
792# module gets started automatically when vinum(8) starts. This
793# device is also untested. Use at your own risk.
794#
795# The option VINUMDEBUG must match the value set in CFLAGS
796# in src/sbin/vinum/Makefile. Failure to do so will result in
797# the following message from vinum(8):
798#
799# Can't get vinum config: Invalid argument
800#
801# see vinum(4) for more reasons not to use these options.
10de45eb 802pseudo-device vinum #Vinum concat/mirror/raid driver
745b8439
SW
803#options VINUMDEBUG #enable Vinum debugging hooks
804
805# Kernel side iconv library
806options LIBICONV
807
808# Size of the kernel message buffer. Should be N * pagesize.
809options MSGBUF_SIZE=40960
810
745b8439
SW
811#####################################################################
812# HARDWARE DEVICE CONFIGURATION
813
814# ISA devices:
815
816#
817# Mandatory ISA devices: isa
818#
819device isa
820
821#
822# Options for `isa':
823#
824# AUTO_EOI_1 enables the `automatic EOI' feature for the master 8259A
825# interrupt controller. This saves about 0.7-1.25 usec for each interrupt.
826# This option breaks suspend/resume on some portables.
827#
828# AUTO_EOI_2 enables the `automatic EOI' feature for the slave 8259A
829# interrupt controller. This saves about 0.7-1.25 usec for each interrupt.
fd7bbe3b 830# Automatic EOI is documented not to work for the slave with the
745b8439
SW
831# original i8259A, but it works for some clones and some integrated
832# versions.
833#
834# MAXMEM specifies the amount of RAM on the machine; if this is not
835# specified, DragonFly will first read the amount of memory from the CMOS
836# RAM, so the amount of memory will initially be limited to 64MB or 16MB
837# depending on the BIOS. If the BIOS reports 64MB, a memory probe will
838# then attempt to detect the installed amount of RAM. If this probe
839# fails to detect >64MB RAM you will have to use the MAXMEM option.
840# The amount is in kilobytes, so for a machine with 128MB of RAM, it would
841# be 131072 (128 * 1024).
842#
843# BROKEN_KEYBOARD_RESET disables the use of the keyboard controller to
844# reset the CPU for reboot. This is needed on some systems with broken
845# keyboard controllers.
846
847options AUTO_EOI_1
848#options AUTO_EOI_2
849options MAXMEM="(128*1024)"
850#options BROKEN_KEYBOARD_RESET
851
852# Enable support for the kernel PLL to use an external PPS signal,
853# under supervision of [x]ntpd(8)
854# More info in ntpd documentation: http://www.eecis.udel.edu/~ntp
855
856options PPS_SYNC
857
858# The keyboard controller; it controls the keyboard and the PS/2 mouse.
859device atkbdc0 at isa? port IO_KBD
860
861# The AT keyboard
862device atkbd0 at atkbdc? irq 1
863
864# Options for atkbd:
865options ATKBD_DFLT_KEYMAP # specify the built-in keymap
866makeoptions ATKBD_DFLT_KEYMAP="jp.106"
867
868# These options are valid for other keyboard drivers as well.
869options KBD_DISABLE_KEYMAP_LOAD # refuse to load a keymap
870options KBD_INSTALL_CDEV # install a CDEV entry in /dev
871
872# `flags' for atkbd:
873# 0x01 Force detection of keyboard, else we always assume a keyboard
874# 0x02 Don't reset keyboard, useful for some newer ThinkPads
875# 0x03 Force detection and avoid reset, might help with certain
876# dockingstations
877# 0x04 Old-style (XT) keyboard support, useful for older ThinkPads
878
879# PS/2 mouse
880device psm0 at atkbdc? irq 12
881
882# Options for psm:
883options PSM_HOOKRESUME #hook the system resume event, useful
884 #for some laptops
885options PSM_RESETAFTERSUSPEND #reset the device at the resume event
886
887device kbdmux # keyboard multiplexer
888
889# The video card driver.
890device vga0 at isa?
891
892# Options for vga:
745b8439
SW
893options VGA_DEBUG=2 # enable VGA debug output
894
895# If you experience problems switching back to 80x25 (or a derived mode),
896# the following option might help.
897#options VGA_KEEP_POWERON_MODE # use power-on settings for 80x25
898
899# If you can dispense with some vga driver features, you may want to
900# use the following options to save some memory.
901#options VGA_NO_FONT_LOADING # don't save/load font
902#options VGA_NO_MODE_CHANGE # don't change video modes
903
904# The following option probably won't work with the LCD displays.
905options VGA_WIDTH90 # support 90 column modes
906
907# Splash screen at start up! Screen savers require this too.
908pseudo-device splash
909
910# The syscons console driver (sco color console compatible).
911device sc0 at isa?
912options MAXCONS=16 # number of virtual consoles
913options SC_ALT_MOUSE_IMAGE # simplified mouse cursor in text mode
914options SC_DEBUG_LEVEL=5 # enable debug output
915options SC_DFLT_FONT # compile font in
916makeoptions SC_DFLT_FONT=cp850
917options SC_DISABLE_DDBKEY # disable `debug' key
918options SC_DISABLE_REBOOT # disable reboot key sequence
919options SC_HISTORY_SIZE=200 # number of history buffer lines
920options SC_MOUSE_CHAR=0x3 # char code for text mode mouse cursor
921options SC_PIXEL_MODE # add support for the raster text mode
922
923# The following options will let you change the default colors of syscons.
924options SC_NORM_ATTR="(FG_GREEN|BG_BLACK)"
925options SC_NORM_REV_ATTR="(FG_YELLOW|BG_GREEN)"
926options SC_KERNEL_CONS_ATTR="(FG_RED|BG_BLACK)"
927options SC_KERNEL_CONS_REV_ATTR="(FG_BLACK|BG_RED)"
928
929# If you have a two button mouse, you may want to add the following option
930# to use the right button of the mouse to paste text.
931options SC_TWOBUTTON_MOUSE
932
933# You can selectively disable features in syscons.
934#options SC_NO_CUTPASTE
935#options SC_NO_FONT_LOADING
936#options SC_NO_HISTORY
937#options SC_NO_SYSMOUSE
938
939#
17f3d27a 940# SCSI host adapters
745b8439
SW
941#
942# adv: All Narrow SCSI bus AdvanSys controllers.
943# adw: Second Generation AdvanSys controllers including the ADV940UW.
745b8439 944# ahc: Adaptec 274x/284x/294x
c67c071b 945# aic: Adaptec 1460
745b8439
SW
946# bt: Most Buslogic controllers
947# ncv: NCR 53C500 based SCSI host adapters.
948# nsp: Workbit Ninja SCSI-3 based PC Card SCSI host adapters.
af2ba4f0 949# stg: TMC 18C30, 18C50 based PC Card SCSI host adapters.
745b8439
SW
950#
951# Note that the order is important in order for Buslogic cards to be
952# probed correctly.
953#
954
17f3d27a 955device bt
e19e3c77 956device adv
745b8439 957device adw
c67c071b 958device aic
745b8439
SW
959device ncv
960device nsp
af2ba4f0 961device stg
745b8439
SW
962
963#
964# Adaptec FSA RAID controllers, including integrated DELL controller,
965# the Dell PERC 2/QC and the HP NetRAID-4M
966#
967device aac
968options AAC_DEBUG
969device aacp # SCSI Passthrough interface (optional, CAM required)
970
971#
972# Compaq Smart RAID, Mylex DAC960 and AMI MegaRAID controllers. Only
973# one entry is needed; the code will find and configure all supported
974# controllers.
975#
976device ida # Compaq Smart RAID
977device mlx # Mylex DAC960
978device amr # AMI MegaRAID
979device amrp # SCSI Passthrough interface (optional, CAM req.)
2063b358 980options AMR_DEBUG=3
745b8439
SW
981device mfi # LSI MegaRAID SAS
982device mfip # LSI MegaRAID SAS passthrough, requires CAM
983options MFI_DEBUG
984
6d743f04
SW
985#
986# LSI MegaRAID 6Gb/s and 12Gb/s SAS+SATA RAID controller driver
987#
988device mrsas
989
745b8439
SW
990#
991# Areca RAID (CAM is required).
992#
993device arcmsr # Areca SATA II RAID
994
995#
996# Highpoint RocketRAID 182x.
997device hptmv
998
0e32bd08
SW
999#
1000# Highpoint RocketRAID. Supports RR172x, RR222x, RR2240, RR232x, RR2340,
1001# RR2210, RR174x, RR2522, RR231x, RR230x.
1002device hptrr
1003
0f74dae5
SW
1004#
1005# Highpoint RocketRAID 27xx.
1006device "hpt27xx"
1007
745b8439
SW
1008#
1009# Highpoint RocketRaid 3xxx series SATA RAID
1010device hptiop
1011
1012#
1013# 3ware ATA RAID
1014#
1015device twe # 3ware ATA RAID
1016device twa # 3ware 9000 series PATA/SATA RAID
1017options TWA_DEBUG=10 # enable debug messages
1018device tws # 3ware 9750 series SATA/SAS RAID
1019
745b8439
SW
1020#
1021# IBM ServeRAID
1022#
1023device ips
1024
745b8439
SW
1025# AHCI driver, this will override NATA for AHCI devices,
1026# both drivers may be included.
1027#
1028device ahci
1029
1030# SiI3124/3132 driver
1031#
1032device sili
1033
df75ede4
SW
1034# The 'NATA' driver supports all ATA and ATAPI devices.
1035# You only need one "device nata" for it to find all
1036# PCI ATA/ATAPI devices on modern machines.
1037#
745b8439
SW
1038device nata
1039device natadisk # ATA disk drives
1040device natapicd # ATAPI CD/DVD drives
1041device natapifd # ATAPI floppy drives
1042device natapist # ATAPI tape drives
1043device natapicam # ATAPI CAM layer emulation
1044device nataraid # support for ATA software RAID controllers
745b8439 1045
df75ede4 1046# The following options are valid for the NATA driver:
745b8439
SW
1047#
1048# ATA_STATIC_ID: controller numbering is static (like the old driver)
1049# else the device numbers are dynamically allocated.
1050options ATA_STATIC_ID
1051
745b8439 1052# For older non-PCI systems, these are the lines to use:
df75ede4
SW
1053#
1054#device nata0 at isa? port IO_WD1 irq 14
1055#device nata1 at isa? port IO_WD2 irq 15
745b8439
SW
1056
1057#
1058# Standard floppy disk controllers: `fdc' and `fd'
1059#
1060#device fdc0 at isa? port IO_FD1 irq 6 drq 2
1061#
1062# FDC_DEBUG enables floppy debugging. Since the debug output is huge, you
1063# gotta turn it actually on by setting the variable fd_debug with DDB,
1064# however.
1065#options FDC_DEBUG
1066
1067#device fd0 at fdc0 drive 0
1068#device fd1 at fdc0 drive 1
1069
745b8439
SW
1070#
1071# sio: serial ports (see sio(4))
1072
1073device sio0 at isa? port IO_COM1 flags 0x10 irq 4
1074
1075#
1076# `flags' for serial drivers that support consoles (only for sio now):
1077# 0x10 enable console support for this unit. The other console flags
1078# are ignored unless this is set. Enabling console support does
1079# not make the unit the preferred console - boot with -h or set
1080# the 0x20 flag for that. Currently, at most one unit can have
1081# console support; the first one (in config file order) with
1082# this flag set is preferred. Setting this flag for sio0 gives
1083# the old behaviour.
1084# 0x20 force this unit to be the console (unless there is another
1085# higher priority console). This replaces the COMCONSOLE option.
1086# 0x40 reserve this unit for low level console operations. Do not
1087# access the device in any normal way.
1088# 0x80 use this port for serial line gdb support in ddb.
1089#
1090# PnP `flags' (set via userconfig using pnp x flags y)
1091# 0x1 disable probing of this device. Used to prevent your modem
1092# from being attached as a PnP modem.
1093#
1094
1095# Options for serial drivers that support consoles (only for sio now):
1096options BREAK_TO_DEBUGGER #a BREAK on a comconsole goes to
1097 #DDB, if available.
1098options CONSPEED=115200 # speed for serial console
1099 # (default 9600)
1100
1101# Solaris implements a new BREAK which is initiated by a character
1102# sequence CR ~ ^b which is similar to a familiar pattern used on
1103# Sun servers by the Remote Console.
1104options ALT_BREAK_TO_DEBUGGER
1105
1106# Options for sio:
1107options COM_ESP #code for Hayes ESP
1108options COM_MULTIPORT #code for some cards with shared IRQs
1109
1110# Other flags for sio that aren't documented in the man page.
1111# 0x20000 enable hardware RTS/CTS and larger FIFOs. Only works for
1112# ST16650A-compatible UARTs.
1113
3323f1c7
SW
1114# PCI Universal Communications driver
1115# Supports various single and multi port PCI serial cards. Maybe later
1116# also the parallel ports on combination serial/parallel cards. New cards
1117# can be added in src/sys/dev/misc/puc/pucdata.c.
1118device puc
1119
745b8439 1120#
ad9f8794 1121# Network interfaces: `ed', `ep', `is', `lnc'
745b8439
SW
1122#
1123# cs: IBM Etherjet and other Crystal Semi CS89x0-based adapters
745b8439
SW
1124# ep: 3Com 3C509
1125# ex: Intel EtherExpress Pro/10 and other i82595-based adapters
745b8439
SW
1126# lnc: Lance/PCnet cards (Isolan, Novell NE2100, NE32-VL, AMD Am7990 & Am79C960)
1127# sbsh: Granch SBNI16 SHDSL modem PCI adapters
1128# wi: Lucent WaveLAN/IEEE 802.11 PCMCIA adapters. Note: this supports both
1129# the PCMCIA and ISA cards: the ISA card is really a PCMCIA to ISA
1130# bridge with a PCMCIA adapter plugged into it.
1131# an: Aironet 4500/4800 802.11 wireless adapters. Supports the PCMCIA,
1132# PCI and ISA varieties.
1133# xe: Xircom/Intel EtherExpress Pro100/16 PC Card ethernet controller.
1134#
e19e3c77 1135device cs
745b8439
SW
1136device ep
1137device ex
e19e3c77 1138device lnc
745b8439 1139device sln
e19e3c77 1140device sn
745b8439
SW
1141
1142# Wlan support is mandatory for some wireless LAN devices.
1143options IEEE80211_DEBUG #enable debugging msgs
1144options IEEE80211_AMPDU_AGE #age frames in AMPDU reorder q's
1145options IEEE80211_SUPPORT_MESH #enable 802.11s D3.0 support
1146options IEEE80211_SUPPORT_TDMA #enable TDMA support
1147device wlan # 802.11 support
1148device wlan_acl # 802.11 MAC-based access control for AP
1149device wlan_ccmp # 802.11 CCMP support
1150device wlan_tkip # 802.11 TKIP support
1151device wlan_wep # 802.11 WEP support
1152device wlan_xauth # 802.11 WPA or 802.1x authentication for AP
1153device wlan_amrr # 802.11 AMRR TX rate control algorithm
1154device an # Aironet Communications 4500/4800
1155device ath # Atheros AR521x
50a82a17
SW
1156options AH_AR5416_INTERRUPT_MITIGATION
1157options AH_ASSERT
1158options AH_DEBUG
1159options AH_INTERRUPT_DEBUGGING
1160options AH_MAXCHAN=96
1161options AH_NEED_DESC_SWAP
1162options AH_PRIVATE_DIAG
1163options AH_REGOPS_FUNC
1164options AH_RXCFG_SDMAMW_4BYTES
1165options AH_SUPPORT_AR5416
1166options AH_SUPPORT_AR9130
1167options AH_SUPPORT_AR9330
1168options AH_SUPPORT_AR9340
1169options AH_USE_INIPDGAIN
745b8439
SW
1170device ath_hal # Atheros Hardware Access Layer
1171#device ath_rate_amrr # Atheros AMRR TX rate control algorithm
1172#device ath_rate_onoe # Atheros Onoe TX rate control algorithm
1173device ath_rate_sample # Atheros Sample TX rate control algorithm
1174options ATH_DEBUG # turn on debugging output (see hw.ath.debug)
1175options ATH_DIAGAPI # diagnostic interface to the HAL
50a82a17
SW
1176options ATH_ENABLE_DFS
1177options ATH_KTR_INTR_DEBUG
745b8439
SW
1178options ATH_RXBUF=80 # number of RX buffers to allocate
1179options ATH_TXBUF=400 # number of TX buffers to allocate
a0ab8429
IV
1180device siba_bwn # Sonic Inc. Silicon Backplane needed for bwn
1181options SIBA_DEBUG # turn on debugging output
1182device bwn # Broadcom BCM43xx NICs using v4 firmware
1183options BWN_DEBUG # turn on debugging output
1184options BWN_RXRING_SLOTS=128 # number of RX slots to allocate
1185options BWN_TXRING_SLOTS=128 # number of TX slots to allocate
745b8439
SW
1186#device iwl # Intel PRO/Wireless 2100
1187device iwi # Intel PRO/Wireless 2200BG/2915ABG
1188device iwn # Intel WiFi Link 4965/1000/5000/5150/5300/6000/6050
459cf836 1189options IWN_DEBUG # turn on debugging output
745b8439
SW
1190device wi # WaveLAN/IEEE, PRISM-II, Spectrum24 802.11DS
1191#device rtw # RealTek 8180
1192#device acx # TI ACX100/ACX111.
1193device xe # Xircom PCMCIA
1194device ral # Ralink Technology 802.11 wireless NIC
1195device wpi
1196
1197# IEEE 802.11 adapter firmware modules
1198
1199# iwifw: Intel PRO/Wireless 2200BG/2225BG/2915ABG firmware
1200# iwnfw: Intel WiFi Link 4965/1000/5000/5150/5300/6000/6050
1201# ralfw: Ralink Technology RT25xx and RT26xx firmware
1202# wpifw: Intel 3945ABG Wireless LAN Controller firmware
1203
1204device iwifw
1205device iwnfw
1206device ralfw
1207device wpifw
1208
1209# Bluetooth Protocols
1210device bluetooth
1211
745b8439
SW
1212# Sound drivers
1213#
745b8439
SW
1214
1215# Basic sound card support:
1216device pcm
43f215d7 1217# For PCI sound cards:
745b8439
SW
1218device "snd_als4000"
1219device "snd_atiixp"
1220device "snd_cmi"
1221device "snd_cs4281"
1222device "snd_csa"
1223device "snd_ds1"
1224device "snd_emu10k1"
3c0a9cdf
SW
1225device "snd_envy24"
1226device "snd_envy24ht"
745b8439 1227device "snd_es137x"
745b8439
SW
1228device "snd_fm801"
1229device "snd_hda"
1230device "snd_ich"
1231device "snd_maestro"
1232device "snd_maestro3"
745b8439 1233device "snd_neomagic"
745b8439 1234device "snd_solo"
3c0a9cdf 1235device "snd_spicds"
745b8439 1236device "snd_t4dwave"
0acb08af 1237device "snd_uaudio"
745b8439
SW
1238device "snd_via8233"
1239device "snd_via82c686"
1240device "snd_vibes"
745b8439
SW
1241
1242#
1243# Miscellaneous hardware:
1244#
1245# bktr: Brooktree bt848/848a/849a/878/879 video capture and TV Tuner board
e147701e 1246# ecc: ECC memory controller
745b8439 1247# joy: joystick
e4c2ac86 1248# nrp: Comtrol Rocketport
745b8439
SW
1249# si: Specialix SI/XIO 4-32 port terminal multiplexor
1250# nmdm: nullmodem terminal driver (see nmdm(4))
f1e3af6c 1251# tpm: Trusted Platform Module
745b8439 1252
745b8439
SW
1253# Notes on the Specialix SI/XIO driver:
1254# **This is NOT a Specialix supported Driver!**
1255# The host card is memory, not IO mapped.
1256# The Rev 1 host cards use a 64K chunk, on a 32K boundary.
1257# The Rev 2 host cards use a 32K chunk, on a 32K boundary.
1258# The cards can use an IRQ of 11, 12 or 15.
1259
e147701e 1260device ecc
745b8439
SW
1261device joy0 at isa? port IO_GAME
1262device nrp
e19e3c77 1263device si
745b8439
SW
1264# nullmodem terminal driver
1265device nmdm
f1e3af6c 1266device tpm
745b8439
SW
1267
1268# The `ahc' device provides support for the Adaptec 274X and 284X
1269# adapters.
1270device ahc
1271
1272# The aic7xxx driver will attempt to use memory mapped I/O for all PCI
1273# controllers that have it configured only if this option is set. Unfortunately,
1274# this doesn't work on some motherboards, which prevents it from being the
1275# default.
1276options AHC_ALLOW_MEMIO
1277
1278# The adw driver will attempt to use memory mapped I/O for all PCI
1279# controllers that have it configured only if this option is set.
1280options ADW_ALLOW_MEMIO
1281
1282#
1283# PCI devices & PCI options:
1284#
1285# The main PCI bus device is `pci'. It provides auto-detection and
1286# configuration support for all devices on the PCI bus, using either
1287# configuration mode defined in the PCI specification.
1288
1289device pci
1290
1291# PCI options
1292#
745b8439
SW
1293options COMPAT_OLDPCI #FreeBSD 2.2 and 3.x compatibility shims
1294
1295# AGP GART support
1296#
1297device agp
1298
7f9ec87c
FT
1299#
1300# AGP debugging.
1301#
1302options AGP_DEBUG
745b8439
SW
1303
1304# The `ahc' device provides support for the Adaptec 29/3940(U)(W)
1305# and motherboard based AIC7870/AIC7880 adapters.
1306options AHC_DEBUG
1307options AHC_DEBUG_OPTS=0xffffffff
1308options AHC_REG_PRETTY_PRINT
1309options AHC_TMODE_ENABLE
1310#
1311# The 'ahd' device provides support for the Adaptec 79xx Ultra320
1312# SCSI adapters. Options are documented in the ahd(4) manpage:
1313options AHD_DEBUG
1314options AHD_DEBUG_OPTS=0xffffffff
1315options AHD_REG_PRETTY_PRINT
1316#options AHD_TMODE_ENABLE=0xff
1317#
1318# The `amd' device provides support for the AMD 53C974 SCSI host
1319# adapter chip as found on devices such as the Tekram DC-390(T).
1320#
1321# The `bge' device provides support for gigabit ethernet adapters
1322# based on the Broadcom BCM570x family of controllers, including the
1323# 3Com 3c996-T, the Netgear GA302T, the SysKonnect SK-9D21 and SK-9D41,
1324# and the embedded gigE NICs on Dell PowerEdge 2550 servers.
1325#
1326# The `ncr' device provides support for the NCR 53C810 and 53C825
1327# self-contained SCSI host adapters.
1328#
1329# The `isp' device provides support for the Qlogic ISP 1020, 1040
1330# nd 1040B PCI SCSI host adapters, ISP 1240 Dual Ultra SCSI,
1331# ISP 1080 and 1280 (Dual) Ultra2, ISP 12160 Ultra3 SCSI, as well as
1332# the Qlogic ISP 2100 and ISP 2200 Fibre Channel Host Adapters.
1333#
1334# The `dc' device provides support for PCI fast ethernet adapters
1335# based on the DEC/Intel 21143 and various workalikes including:
1336# the ADMtek AL981 Comet and AN985 Centaur, the ASIX Electronics
1337# AX88140A and AX88141, the Davicom DM9100 and DM9102, the Lite-On
1338# 82c168 and 82c169 PNIC, the Lite-On/Macronix LC82C115 PNIC II
1339# and the Macronix 98713/98713A/98715/98715A/98725 PMAC. This driver
1340# replaces the old al, ax, dm, pn and mx drivers. List of brands:
1341# Digital DE500-BA, Kingston KNE100TX, D-Link DFE-570TX, SOHOware SFA110,
1342# SVEC PN102-TX, CNet Pro110B, 120A, and 120B, Compex RL100-TX,
1343# LinkSys LNE100TX, LNE100TX V2.0, Jaton XpressNet, Alfa Inc GFC2204,
1344# KNE110TX.
1345#
1346# The `de' device provides support for the Digital Equipment DC21040
1347# self-contained Ethernet adapter.
1348#
1349# The `em' device provides support for the Intel Pro/1000 Family of Gigabit
1350# adapters (82542, 82543, 82544, 82540).
1351#
1352# The `et' device provides support for the Agere ET1310 10/100/1000 PCIe
1353# adapters.
1354#
1355# The `fxp' device provides support for the Intel EtherExpress Pro/100B
1356# PCI Fast Ethernet adapters.
1357#
1358# The 'lge' device provides support for PCI gigabit ethernet adapters
1359# based on the Level 1 LXT1001 NetCellerator chipset. This includes the
1360# D-Link DGE-500SX, SMC TigerCard 1000 (SMC9462SX), and some Addtron cards.
1361#
1362# The 'my' device provides support for the Myson MTD80X and MTD89X PCI
1363# Fast Ethernet adapters.
1364#
1365# The 'nge' device provides support for PCI gigabit ethernet adapters
1366# based on the National Semiconductor DP83820 and DP83821 chipset. This
1367# includes the SMC EZ Card 1000 (SMC9462TX), D-Link DGE-500T, Asante
1368# FriendlyNet GigaNIX 1000TA and 1000TPC, the Addtron AEG320T, the
1369# LinkSys EG1032 and EG1064, the Surecom EP-320G-TX and the Netgear GA622T.
1370#
229aec1c
SW
1371# The 'oce' device provides support for Emulex 10 Gbit adapters
1372# (OneConnect Ethernet).
1373#
745b8439
SW
1374# The 'pcn' device provides support for PCI fast ethernet adapters based
1375# on the AMD Am79c97x chipsets, including the PCnet/FAST, PCnet/FAST+,
1376# PCnet/PRO and PCnet/Home. These were previously handled by the lnc
1377# driver (and still will be if you leave this driver out of the kernel).
1378#
1379# Te 're' device provides support for PCI GigaBit ethernet adapters based
1380# on the RealTek 8169 chipset. It also supports the 8139C+ and is the
1381# preferred driver for that chip.
1382#
1383# The 'rl' device provides support for PCI fast ethernet adapters based
1384# on the RealTek 8129/8139 chipset. Note that the RealTek driver defaults
1385# to using programmed I/O to do register accesses because memory mapped
1386# mode seems to cause severe lockups on SMP hardware. This driver also
1387# supports the Accton EN1207D `Cheetah' adapter, which uses a chip called
1388# the MPX 5030/5038, which is either a RealTek in disguise or a RealTek
1389# workalike. Note that the D-Link DFE-530TX+ uses the RealTek chipset
1390# and is supported by this driver, not the 'vr' driver.
1391#
1392# The 'sf' device provides support for Adaptec Duralink PCI fast
1393# ethernet adapters based on the Adaptec AIC-6915 "starfire" controller.
1394# This includes dual and quad port cards, as well as one 100baseFX card.
1395# Most of these are 64-bit PCI devices, except for one single port
1396# card which is 32-bit.
1397#
1398# The 'ste' device provides support for adapters based on the Sundance
1399# Technologies ST201 PCI fast ethernet controller. This includes the
1400# D-Link DFE-550TX.
1401#
1402# The 'sis' device provides support for adapters based on the Silicon
1403# Integrated Systems SiS 900 and SiS 7016 PCI fast ethernet controller
1404# chips.
1405#
1406# The 'sk' device provides support for the SysKonnect SK-984x series
1407# PCI gigabit ethernet NICs. This includes the SK-9841 and SK-9842
1408# single port cards (single mode and multimode fiber) and the
1409# SK-9843 and SK-9844 dual port cards (also single mode and multimode).
1410# The driver will autodetect the number of ports on the card and
1411# attach each one as a separate network interface.
1412#
1413# The 'ti' device provides support for PCI gigabit ethernet NICs based
1414# on the Alteon Networks Tigon 1 and Tigon 2 chipsets. This includes the
1415# Alteon AceNIC, the 3Com 3c985, the Netgear GA620 and various others.
1416# Note that you will probably want to bump up NMBCLUSTERS a lot to use
1417# this driver.
1418#
1419# The 'tl' device provides support for the Texas Instruments TNETE100
1420# series 'ThunderLAN' cards and integrated ethernet controllers. This
1421# includes several Compaq Netelligent 10/100 cards and the built-in
1422# ethernet controllers in several Compaq Prosignia, Proliant and
1423# Deskpro systems. It also supports several Olicom 10Mbps and 10/100
1424# boards.
1425#
1426# The `tx' device provides support for the SMC 9432 TX, BTX and FTX cards.
1427#
1428# The `txp' device provides support for the 3Com 3cR990 "Typhoon"
1429# 10/100 adapters.
1430#
1431# The `vr' device provides support for various fast ethernet adapters
1432# based on the VIA Technologies VT3043 `Rhine I' and VT86C100A `Rhine II'
1433# chips, including the D-Link DFE530TX (see 'rl' for DFE530TX+), the Hawking
1434# Technologies PN102TX, and the AOpen/Acer ALN-320.
1435#
1436# The `vx' device provides support for the 3Com 3C590 and 3C595
1437# early support
1438#
1439# The `wb' device provides support for various fast ethernet adapters
1440# based on the Winbond W89C840F chip. Note: this is not the same as
1441# the Winbond W89C940F, which is an NE2000 clone.
1442#
1443# The `xl' device provides support for the 3Com 3c900, 3c905 and
1444# 3c905B (Fast) Etherlink XL cards and integrated controllers. This
1445# includes the integrated 3c905B-TX chips in certain Dell Optiplex and
1446# Dell Precision desktop machines and the integrated 3c905-TX chips
1447# in Dell Latitude laptop docking stations.
1448#
1449# The 'bktr' device is a PCI video capture device using the Brooktree
1450# bt848/bt848a/bt849a/bt878/bt879 chipset. When used with a TV Tuner it forms a
1451# TV card, eg Miro PC/TV, Hauppauge WinCast/TV WinTV, VideoLogic Captivator,
1452# Intel Smart Video III, AverMedia, IMS Turbo, FlyVideo.
1453#
1454# options OVERRIDE_CARD=xxx
1455# options OVERRIDE_TUNER=xxx
1456# options OVERRIDE_MSP=1
1457# options OVERRIDE_DBX=1
1458# These options can be used to override the auto detection
1459# The current values for xxx are found in src/sys/dev/video/bktr/bktr_card.h
1460# Using sysctl(8) run-time overrides on a per-card basis can be made
1461#
1462# options BKTR_SYSTEM_DEFAULT=BROOKTREE_PAL
1463# or
1464# options BKTR_SYSTEM_DEFAULT=BROOKTREE_NTSC
8d67cbb3 1465# Specifies the default video capture mode.
745b8439
SW
1466# This is required for Dual Crystal (28&35Mhz) boards where PAL is used
1467# to prevent hangs during initialisation. eg VideoLogic Captivator PCI.
1468#
1469# options BKTR_USE_PLL
1470# PAL or SECAM users who have a 28Mhz crystal (and no 35Mhz crystal)
1471# must enable PLL mode with this option. eg some new Bt878 cards.
1472#
1473# options BKTR_GPIO_ACCESS
1474# This enable IOCTLs which give user level access to the GPIO port.
1475#
1476# options BKTR_NO_MSP_RESET
1477# Prevents the MSP34xx reset. Good if you initialise the MSP in another OS first
1478#
1479# options BKTR_430_FX_MODE
1480# Switch Bt878/879 cards into Intel 430FX chipset compatibility mode.
1481#
1482# options BKTR_SIS_VIA_MODE
1483# Switch Bt878/879 cards into SIS/VIA chipset compatibility mode which is
1484# needed for some old SiS and VIA chipset motherboards.
1485# This also allows Bt878/879 chips to work on old OPTi (<1997) chipset
1486# motherboards and motherboards with bad or incomplete PCI 2.1 support.
1487# As a rough guess, old = before 1998
1488#
1489# options BKTR_NEW_MSP34XX_DRIVER
1490# Use new, more complete initialization scheme for the msp34* soundchip.
1491# Should fix stereo autodetection if the old driver does only output
1492# mono sound.
1493#
1494# options BKTR_OVERRIDE_CARD=xxx
1495# options BKTR_OVERRIDE_DBX=xxx
1496# options BKTR_OVERRIDE_MSP=xxx
1497# options BKTR_OVERRIDE_TUNER=xxx
1498# These options can be used to select a specific device, regardless of
1499# the autodetection and i2c device checks (see comments in bktr_card.c).
1500#
1501device ahc # AHA2940 and onboard AIC7xxx devices
1502device ahd # AIC79xx devices
1503device amd # AMD 53C974 (Tekram DC-390(T))
1504device isp # Qlogic family
1505device ispfw # Firmware for QLogic HBAs
1506device mpt # LSI '909 FC adapters
1507device mps # LSI-Logic MPT-Fusion 2
1508device ncr # NCR/Symbios Logic
1509device sym # NCR/Symbios Logic (newer chipsets)
1510device trm # Tekram DC395U/UW/F and DC315U
1511#
1512# Options for ISP
1513#
1514# ISP_TARGET_MODE - enable target mode operation
1515#options ISP_TARGET_MODE=1
1516
47a69c3f 1517# Options used in dev/disk/sym/ (Symbios SCSI driver).
745b8439
SW
1518#options SYM_SETUP_LP_PROBE_MAP #-Low Priority Probe Map (bits)
1519 # Allows the ncr to take precedence
1520 # 1 (1<<0) -> 810a, 860
1521 # 2 (1<<1) -> 825a, 875, 885, 895
1522 # 4 (1<<2) -> 895a, 896, 1510d
1523#options SYM_SETUP_SCSI_DIFF #-HVD support for 825a, 875, 885
1524 # disabled:0 (default), enabled:1
1525#options SYM_SETUP_PCI_PARITY #-PCI parity checking
1526 # disabled:0, enabled:1 (default)
1527#options SYM_SETUP_MAX_LUN #-Number of LUNs supported
1528 # default:8, range:[1..64]
1529
1530
1531# MII bus support is required for some PCI 10/100 ethernet NICs,
1532# namely those which use MII-compliant transceivers or implement
1533# transceiver control interfaces that operate like an MII. Adding
1534# "device miibus0" to the kernel config pulls in support for
1535# the generic miibus API and all of the PHY drivers, including a
1536# generic one for PHYs that aren't specifically handled by an
1537# individual driver.
1538device miibus
1539
1540# PCI Ethernet NICs that use the common MII bus controller code.
1541device ae # Attansic/Atheros L2 Fast Ethernet
1542device alc # Atheros AR8131/AR8132
1543device ale # Atheros AR8121/AR8113/AR8114
1544device age # Attansic/Atheros L1 Gigabit Ethernet
1545device bce # Broadcom NetXtreme II Gigabit Ethernet
1546device bfe # Broadcom BCM440x 10/100 Ethernet
6c8d8ecc 1547device bnx # Broadcom NetXtreme 5718/57785 Gigabit Ethernet
745b8439
SW
1548device dc # DEC/Intel 21143 and various workalikes
1549device fxp # Intel EtherExpress PRO/100B (82557, 82558)
1550device my # Myson Fast Ethernet (MTD80X, MTD89X)
1551device pcn # AMD Am79C97x PCI 10/100 NICs
1552device re # RealTek 8139C+/8169
1553device rl # RealTek 8129/8139
1554device sbsh # Granch SBNI16 SHDSL modem
1555device sf # Adaptec AIC-6915 (``Starfire'')
1556device sis # Silicon Integrated Systems SiS 900/SiS 7016
1557device ste # Sundance ST201 (D-Link DFE-550TX)
1558device tl # Texas Instruments ThunderLAN
1559device tx # SMC EtherPower II (83c17x ``EPIC'')
1560device vge # VIA 612x GigE
1561device vr # VIA Rhine, Rhine II
1562device wb # Winbond W89C840F
1563device xl # 3Com 3c90x (``Boomerang'', ``Cyclone'')
1564
1565# PCI Ethernet NICs.
1566device de # DEC/Intel DC21x4x (``Tulip'')
1567device txp # 3Com 3cR990 (``Typhoon'')
1568device vx # 3Com 3c590, 3c595 (``Vortex'')
1569
1570# Gigabit Ethernet NICs.
1571device bge # Broadcom BCM570x (``Tigon III'')
1572device em # Intel Pro/1000 (8254x,8257x)
1573 # Requires ig_hal
1574device emx # Intel Pro/1000 (8257{1,2,3,4})
1575 # Requires ig_hal
1f7e3916
SZ
1576device igb # Intel Pro/1000 (82575, 82576, 82580, i350)
1577 # Requires ig_hal
745b8439 1578device ig_hal # Intel Pro/1000 hardware abstraction layer
79251f5e 1579device ix # Intel PRO/10GbE PCIE Ethernet Family
745b8439
SW
1580device et # Agere ET1310 10/100/1000 Ethernet
1581device lge # Level 1 LXT1001 (``Mercury'')
1582device mxge # Myricom Myri-10G 10GbE NIC
1583device nfe # nVidia nForce2/3 MCP04/51/55 CK804
1584device nge # NatSemi DP83820 and DP83821
229aec1c 1585device oce # Emulex 10 GbE (OneConnect Ethernet)
745b8439
SW
1586device sk # SysKonnect GEnesis, LinkSys EG1023, D-Link
1587device ti # Alteon (``Tigon I'', ``Tigon II'')
1588device stge # Sundance/Tamarack TC9021 Gigabit Ethernet
1589device msk # Marvell/SysKonnect Yukon II Gigabit Ethernet
1590device jme # JMicron Gigabit/Fast Ethernet
1591
1592# Brooktree driver has been ported to the new I2C framework. Thus,
1593# you'll need to have the following 3 lines in the kernel config.
1594# device smbus
1595# device iicbus
1596# device iicbb
1597# The iic and smb devices are only needed if you want to control other
1598# I2C slaves connected to the external connector of some cards.
1599#
1600device bktr
1601options BKTR_NEW_MSP34XX_DRIVER
1602
1603# WinTV PVR-250/350 driver
1604device cxm
1605
1606#
1607# PCCARD/PCMCIA
1608#
1609# pccard: pccard slots
1610# cardbus/cbb: cardbus bridge
1611device pccard
1612device cardbus
1613device cbb
1614
1615# For older notebooks that signal a powerfail condition (external
1616# power supply dropped, or battery state low) by issuing an NMI:
1617
1618options POWERFAIL_NMI # make it beep instead of panicing
1619
1620#
1621# MMC/SD
1622#
1623# mmc MMC/SD bus
1624# mmcsd MMC/SD memory card
1625# sdhci Generic PCI SD Host Controller
1626#
1627device mmc
1628device mmcsd
1629device sdhci
1630
1631#
1632# SMB bus
1633#
1634# System Management Bus support is provided by the 'smbus' device.
1635# Access to the SMBus device is via the 'smb' device (/dev/smb*),
1636# which is a child of the 'smbus' device.
1637#
1638# Supported devices:
1639# smb standard io through /dev/smb*
1640#
1641# Supported SMB interfaces:
1642# iicsmb I2C to SMB bridge with any iicbus interface
1643# bktr brooktree848 I2C hardware interface
1644# intpm Intel PIIX4 (82371AB, 82443MX) Power Management Unit
1645# alpm Acer Aladdin-IV/V/Pro2 Power Management Unit
8ceadc27 1646# ichiic Intel generation 4 I2C controller
745b8439
SW
1647# ichsmb Intel ICH SMBus controller chips (82801AA, 82801AB, 82801BA)
1648# viapm VIA VT82C586B,596,686A and VT8233 SMBus controllers
1649# amdpm AMD 756 Power Management Unit
1650# amdsmb AMD 8111 SMBus 2.0 Controller
1651#
1652device smbus # Bus support, required for smb below.
1653
1654device intpm
1655device alpm
8ceadc27 1656device ichiic
745b8439
SW
1657device ichsmb
1658device viapm
1659device amdpm
1660device amdsmb
1661
1662device smb
1663
1664#
1665# I2C Bus
1666#
1667# Philips i2c bus support is provided by the `iicbus' device.
1668#
1669# Supported devices:
1670# ic i2c network interface
1671# iic i2c standard io
1672# iicsmb i2c to smb bridge. Allow i2c i/o with smb commands.
1673#
1674# Supported interfaces:
1675# pcf Philips PCF8584 ISA-bus controller
1676# bktr brooktree848 I2C software interface
1677#
1678# Other:
1679# iicbb generic I2C bit-banging code (needed by lpbb, bktr)
1680#
1681device iicbus # Bus support, required for ic/iic/iicsmb below.
1682device iicbb
1683
1684device ic
1685device iic
1686device iicsmb # smb over i2c bridge
1687
1688device pcf0 at isa? port 0x320 irq 5
1689
73e10c03
SZ
1690# Intel performance-energy bias
1691device perfbias
1692
e76f5e73
SZ
1693# Intel software controlled clock modulation
1694device clockmod
1695
745b8439
SW
1696# Intel Core and newer CPUs on-die digital thermal sensor support
1697device coretemp
1698
1699# AMD Family 0Fh, 10h and 11h temperature sensors
1700device kate
1701device km
1702
1703# ThinkPad Active Protection System accelerometer
1704device aps0 at isa? port 0x1600
1705
1706# HW monitoring devices lm(4), it(4) and nsclpcsio.
1707device lm0 at isa? port 0x290
1708device it0 at isa? port 0x290
1709device it1 at isa? port 0xc00
1710device it2 at isa? port 0xd00
1711device it3 at isa? port 0x228
1712device nsclpcsio0 at isa? port 0x2e
1713device nsclpcsio1 at isa? port 0x4e
1714device wbsio0 at isa? port 0x2e
1715device wbsio1 at isa? port 0x4e
1716device lm#3 at wbsio?
1717device uguru0 at isa? port 0xe0 # ABIT uGuru
1718
745b8439
SW
1719# Parallel-Port Bus
1720#
1721# Parallel port bus support is provided by the `ppbus' device.
1722# Multiple devices may be attached to the parallel port, devices
1723# are automatically probed and attached when found.
1724#
1725# Supported devices:
1726# vpo Iomega Zip Drive
1727# Requires SCSI disk support ('scbus' and 'da'); the best
1728# performance is achieved with ports in EPP 1.9 mode.
1729# lpt Parallel Printer
1730# plip Parallel network interface
1731# ppi General-purpose I/O ("Geek Port") + IEEE1284 I/O
1732# pps Pulse per second Timing Interface
1733# lpbb Philips official parallel port I2C bit-banging interface
1734#
1735# Supported interfaces:
1736# ppc ISA-bus parallel port interfaces.
1737#
1738
1739options PPC_PROBE_CHIPSET # Enable chipset specific detection
1740 # (see flags in ppc(4))
1741options DEBUG_1284 # IEEE1284 signaling protocol debug
1742options PERIPH_1284 # Makes your computer act as a IEEE1284
1743 # compliant peripheral
1744options DONTPROBE_1284 # Avoid boot detection of PnP parallel devices
1745options VP0_DEBUG # ZIP/ZIP+ debug
1746options LPT_DEBUG # Printer driver debug
1747options PPC_DEBUG=2 # Parallel chipset level debug
1748options PLIP_DEBUG # Parallel network IP interface debug
1749options PCFCLOCK_VERBOSE # Verbose pcfclock driver
1750options PCFCLOCK_MAX_RETRIES=5 # Maximum read tries (default 10)
1751
1752device ppc0 at isa? irq 7
1753device ppbus
1754device vpo
1755device lpt
1756device plip
1757device ppi
1758device pps
1759device lpbb
1760device pcfclock
1761
1762# Kernel BOOTP support
1763
1764options BOOTP # Use BOOTP to obtain IP address/hostname
1765options BOOTP_NFSROOT # NFS mount root filesystem using BOOTP info
1766options BOOTP_NFSV3 # Use NFS v3 to NFS mount root
1767options BOOTP_COMPAT # Workaround for broken bootp daemons.
1768options BOOTP_WIRED_TO=fxp0 # Use interface fxp0 for BOOTP
1769
745b8439
SW
1770#
1771# Set the number of PV entries per process. Increasing this can
1772# stop panics related to heavy use of shared memory. However, that can
1773# (combined with large amounts of physical memory) cause panics at
1774# boot time due the kernel running out of VM space.
1775#
1776# If you're tweaking this, you might also want to increase the sysctls
1777# "vm.v_free_min", "vm.v_free_reserved", and "vm.v_free_target".
1778#
1779# The value below is the one more than the default.
1780#
1781options PMAP_SHPGPERPROC=201
1782
1783#
1784# Disable swapping. This option removes all code which actually performs
1785# swapping, so it's not possible to turn it back on at run-time.
1786#
1787# This is sometimes usable for systems which don't have any swap space
1788# (see also sysctls "vm.defer_swapspace_pageouts" and
1789# "vm.disable_swapspace_pageouts")
1790#
1791#options NO_SWAPPING
1792
1793# Set the size of the buffer cache KVM reservation, in buffers. This is
1794# scaled by approximately 16384 bytes. The system will auto-size the buffer
1795# cache if this option is not specified.
1796#
1797options NBUF=512
1798
1799# Set the size of the mbuf KVM reservation, in clusters. This is scaled
1800# by approximately 2048 bytes. The system will auto-size the mbuf area
1801# to (512 + maxusers*16) if this option is not specified.
1802# maxusers is in turn computed at boot time depending on available memory
1803# or set to the value specified by "options MAXUSERS=x" (x=0 means
1804# autoscaling).
1805# So, to take advantage of autoscaling, you have to remove both
1806# NMBCLUSTERS and MAXUSERS (and NMBUFS) from your kernel config.
1807#
1808options NMBCLUSTERS=1024
1809
1810# Set the number of mbufs available in the system. Each mbuf
1811# consumes 256 bytes. The system will autosize this (to 4 times
1812# the number of NMBCLUSTERS, depending on other constraints)
1813# if this option is not specified.
1814#
1815options NMBUFS=4096
1816
1817# Tune the buffer cache maximum KVA reservation, in bytes. The maximum is
1818# usually capped at 200 MB, effecting machines with > 1GB of ram. Note
1819# that the buffer cache only really governs write buffering and disk block
1820# translations. The VM page cache is our primary disk cache and is not
1821# effected by the size of the buffer cache.
1822#
1823options VM_BCACHE_SIZE_MAX="(100*1024*1024)"
1824
1825# Tune the swap zone KVA reservation, in bytes. The default is typically
1826# 70 MB, giving the system the ability to manage a maximum of 28GB worth
1827# of swapped out data.
1828#
1829options VM_SWZONE_SIZE_MAX="(50*1024*1024)"
1830
1831#
1832# Enable extra debugging code for locks. This stores the filename and
1833# line of whatever acquired the lock in the lock itself, and change a
1834# number of function calls to pass around the relevant data. This is
1835# not at all useful unless you are debugging lock code. Also note
1836# that it is likely to break e.g. fstat(1) unless you recompile your
1837# userland with -DDEBUG_LOCKS as well.
1838#
9ec899f4
SW
1839# DEBUG_LOCKS_LATENCY adds a sysctl to add a forced latency loop
1840# (count to N) in front of any spinlock or gettoken.
1841#
745b8439 1842options DEBUG_LOCKS
9ec899f4 1843options DEBUG_LOCKS_LATENCY
745b8439
SW
1844
1845# Set the amount of time (in seconds) the system will wait before
1846# rebooting automatically when a kernel panic occurs. If set to (-1),
1847# the system will wait indefinitely until a key is pressed on the
1848# console.
1849options PANIC_REBOOT_WAIT_TIME=16
1850
1851# Attempt to bypass the buffer cache and put data directly into the
1852# userland buffer for read operation when O_DIRECT flag is set on the
1853# file. Both offset and length of the read operation must be
1854# multiples of the physical media sector size.
1855#
1856options DIRECTIO
1857
1858# Specify a lower limit for the number of swap I/O buffers. They are
1859# (among other things) used when bypassing the buffer cache due to
1860# DIRECTIO kernel option enabled and O_DIRECT flag set on file.
1861#
1862#options NSWBUF_MIN=120
1863
1864# The 'asr' driver provides support for current DPT/Adaptec SCSI RAID
1865# controllers (SmartRAID V and VI and later).
1866# These controllers require the CAM infrastructure.
1867#
1868device asr
1869
1870# The 'dpt' driver provides support for DPT controllers (http://www.dpt.com/).
1871# These have hardware RAID-{0,1,5} support, and do multi-initiator I/O.
1872# The DPT controllers are commonly re-licensed under other brand-names -
1873# some controllers by Olivetti, Dec, HP, AT&T, SNI, AST, Alphatronic, NEC and
1874# Compaq are actually DPT controllers.
1875#
1876# See src/sys/dev/raid/dpt for debugging and other subtle options.
1877# DPT_MEASURE_PERFORMANCE Enables a set of (semi)invasive metrics. Various
1878# instruments are enabled. The tools in
1879# /usr/sbin/dpt_* assume these to be enabled.
1880# DPT_HANDLE_TIMEOUTS Normally device timeouts are handled by the DPT.
1881# If you ant the driver to handle timeouts, enable
1882# this option. If your system is very busy, this
1883# option will create more trouble than solve.
1884# DPT_TIMEOUT_FACTOR Used to compute the excessive amount of time to
1885# wait when timing out with the above option.
47a69c3f 1886# DPT_DEBUG_xxxx These are controllable from sys/dev/raid/dpt/dpt.h
745b8439
SW
1887# DPT_LOST_IRQ When enabled, will try, once per second, to catch
1888# any interrupt that got lost. Seems to help in some
1889# DPT-firmware/Motherboard combinations. Minimal
1890# cost, great benefit.
1891# DPT_RESET_HBA Make "reset" actually reset the controller
1892# instead of fudging it. Only enable this if you
1893# are 100% certain you need it.
1894
1895device dpt
1896
1897# DPT options
1898#!CAM# options DPT_MEASURE_PERFORMANCE
1899#!CAM# options DPT_HANDLE_TIMEOUTS
1900options DPT_TIMEOUT_FACTOR=4
1901options DPT_LOST_IRQ
1902options DPT_RESET_HBA
1903
1904#
1905# Compaq "CISS" RAID controllers (SmartRAID 5* series)
1906# These controllers have a SCSI-like interface, and require the
1907# CAM infrastructure.
1908#
1909device ciss
1910
1911#
1912# Intel Integrated RAID controllers.
1913# This driver is supported and maintained by
1914# "Leubner, Achim" <Achim_Leubner@adaptec.com>.
1915#
1916device iir
1917
1918#
1919# Mylex AcceleRAID and eXtremeRAID controllers with v6 and later
1920# firmware. These controllers have a SCSI-like interface, and require
1921# the CAM infrastructure.
1922#
1923device mly
1924
1925# USB support
886e1e50 1926#
886e1e50 1927
745b8439
SW
1928# UHCI controller
1929device uhci
1930# OHCI controller
1931device ohci
1932# EHCI controller
b4ea5ff5
SW
1933device ehci
1934# XHCI controller
1935device xhci
745b8439
SW
1936# General USB code (mandatory for USB)
1937device usb
745b8439
SW
1938# Human Interface Device (anything with buttons and dials)
1939device uhid
1940# USB keyboard
1941device ukbd
1942# USB printer
1943device ulpt
0e20af68 1944# USB mass storage (Requires scbus and da)
745b8439 1945device umass
b4ea5ff5
SW
1946# USB mass storage driver for device-side mode
1947device usfs
745b8439
SW
1948# USB modem support
1949device umodem
1950# USB mouse
1951device ums
b4ea5ff5
SW
1952# eGalax USB touch screen
1953device uep
745b8439 1954# USB com devices
b4ea5ff5 1955device "u3g"
745b8439
SW
1956device uark
1957device ubsa
b4ea5ff5 1958device ubser
745b8439
SW
1959device uchcom
1960device ucom
b4ea5ff5
SW
1961device ucycom
1962device ufoma
745b8439
SW
1963device uftdi
1964device ugensa
b4ea5ff5
SW
1965device uipaq
1966device umcs
745b8439 1967device umct
b4ea5ff5 1968device umoscom
745b8439
SW
1969device uplcom
1970device uslcom
745b8439
SW
1971device uvisor
1972device uvscom
1973
b4ea5ff5
SW
1974#
1975# USB ethernet support
1976device uether
745b8439 1977#
79be21c5
SW
1978# ADMtek USB ethernet. Supports the LinkSys USB100TX,
1979# the Billionton USB100, the Melco LU-ATX, the D-Link DSB-650TX
1980# and the SMC 2202USB. Also works with the ADMtek AN986 Pegasus
1981# eval board.
1982device aue
1983#
745b8439
SW
1984# ASIX Electronics AX88172 USB 2.0 ethernet driver. Used in the
1985# LinkSys USB200M and various other adapters.
1986device axe
b4ea5ff5 1987#
3d2b9530
SW
1988# ASIX Electronics AX88178A/AX88179 USB 2.0/3.0 gigabit ethernet driver.
1989device axge
1990#
79be21c5
SW
1991# CATC USB-EL1201A USB ethernet. Supports the CATC Netmate
1992# and Netmate II, and the Belkin F5U111.
1993device cue
1994#
1995# USB Apple iPhone/iPad tethered Ethernet driver
1996device ipheth
1997#
1998# Kawasaki LSI ethernet. Supports the LinkSys USB10T,
1999# Entrega USB-NET-E45, Peracom Ethernet Adapter, the
2000# 3Com 3c19250, the ADS Technologies USB-10BT, the ATen UC10T,
2001# the Netgear EA101, the D-Link DSB-650, the SMC 2102USB
2002# and 2104USB, and the Corega USB-T.
2003device kue
2004#
f8577199
SW
2005# Moschip MCS7730/MCS7840 USB to fast ethernet. Supports the Sitecom LN030.
2006device mos
2007#
b4ea5ff5
SW
2008# Davicom DM9601E USB to fast ethernet. Supports the Corega FEther USB-TXC.
2009device udav
745b8439
SW
2010
2011# USB wireless NICs, requires wlan_amrr
2012#
2013# Ralink Technology RT2501USB/RT2601USB
f794c13f 2014device rum
790340ea 2015#
10f2cea7
SW
2016# Ralink Technology RT2700U/RT2800U/RT3000U wireless driver
2017device run
2018device runfw
745b8439 2019#
e4ca69a1
SW
2020# RNDIS USB ethernet driver
2021device urndis
2022#
790340ea
SW
2023# Realtek RTL8188CU/RTL8192CU wireless driver
2024device urtwn
2025device urtwnfw
745b8439 2026
4596d2c5
SW
2027# Fm Radio
2028#
2029device ufm
2030
a7ceaa31
SW
2031# Templates for programming USB device side drivers
2032#
2033device usb_template
2034
745b8439
SW
2035# debugging options for the USB subsystem
2036#
2037options USB_DEBUG
2038
2039# options for ukbd:
2040options UKBD_DFLT_KEYMAP # specify the built-in keymap
2041makeoptions UKBD_DFLT_KEYMAP=it.iso
2042
2043# Firewire support
2044device firewire # Firewire bus code
2045device sbp # SCSI over Firewire (Requires scbus and da)
2046device fwe # Ethernet over Firewire (non-standard!)
2047
2048# dcons support (Dumb Console Device)
2049device dcons # dumb console driver
2050device dcons_crom # FireWire attachment
2051options DCONS_BUF_SIZE=16384 # buffer size
2052options DCONS_POLL_HZ=100 # polling rate
2053options DCONS_FORCE_CONSOLE=1 # force to be the primary console
2054options DCONS_FORCE_GDB=1 # force to be the gdb device
2055
2056#####################################################################
2057# crypto subsystem
2058#
2059# This is a port of the openbsd crypto framework. Include this when
2060# configuring IPsec and when you have a h/w crypto device to accelerate
2061# user applications that link to openssl.
2062#
2063# Drivers are ports from openbsd with some simple enhancements that have
2064# been fed back to openbsd (and hopefully will be included).
2065
2066pseudo-device crypto # core crypto support
2067pseudo-device cryptodev # /dev/crypto for access to h/w
2068
2069device rndtest # FIPS 140-2 entropy tester
2070
2071device hifn # Hifn 7951, 7781, etc.
2072options HIFN_DEBUG # enable debugging support: hw.hifn.debug
2073#options HIFN_NO_RNG # for devices without RNG
2074options HIFN_RNDTEST # enable rndtest support
2075
25638cf4
SW
2076device safe # SafeNet 1141
2077options SAFE_DEBUG # enable debugging support: hw.safe.debug
8690ff8f 2078#options SAFE_NO_RNG # for devices without RNG
25638cf4
SW
2079options SAFE_RNDTEST # enable rndtest support
2080
745b8439
SW
2081device ubsec # Broadcom 5501, 5601, 58xx
2082options UBSEC_DEBUG # enable debugging support: hw.ubsec.debug
2083#options UBSEC_NO_RNG # for devices without RNG
2084options UBSEC_RNDTEST # enable rndtest support
2085
2086device aesni # hardware crypto/RNG for AES-NI
2087device padlock # hardware crypto/RNG for VIA C3/C7/Eden
c5761ad0 2088device rdrand # hardware RNG for RdRand
745b8439
SW
2089
2090#
2091# ACPI support using the Intel ACPI Component Architecture reference
2092# implementation.
2093#
2094# ACPI_DEBUG enables the use of the debug.acpi.level and debug.acpi.layer
2095# kernel environment variables to select initial debugging levels for the
2096# Intel ACPICA code.
2097#
2098# Note that building ACPI into the kernel is deprecated; the module is
2099# normally loaded automatically by the loader.
2100
2101device acpi
2102options ACPI_DEBUG
2103
554257bc
SW
2104# ACPI WMI Mapping driver
2105device acpi_wmi
2106
745b8439
SW
2107# ACPI Asus Extras (LCD backlight/brightness, video output, etc.)
2108device acpi_asus
2109
2110# ACPI Fujitsu Extras (Buttons)
2111device acpi_fujitsu
2112
2113# ACPI extras driver for HP laptops
554257bc 2114device acpi_hp
745b8439
SW
2115
2116# ACPI Panasonic Extras (LCD backlight/brightness, video output, etc.)
2117device acpi_panasonic
2118
2119# ACPI Sony extra (LCD brightness)
2120device acpi_sony
2121
2122# ACPI extras driver for ThinkPad laptops
2123device acpi_thinkpad
2124
2125# ACPI Toshiba Extras (LCD backlight/brightness, video output, etc.)
2126device acpi_toshiba
2127
2128# ACPI Video Extensions (LCD backlight/brightness, video output, etc.)
2129device acpi_video
2130
90980aa5
SW
2131# ACPI Docking Station
2132device acpi_dock
2133
745b8439
SW
2134device aibs # ASUSTeK AI Booster (ACPI ASOC ATK0110)
2135
2136# DRM options:
2137# drm: General DRM code
86689d3d 2138# i915kmsdrm: Intel integrated GPUs, starting from the 830M family
f3d5536d 2139# radeonkmsdrm: ATI Radeon cards
745b8439
SW
2140#
2141# DRM_DEBUG: include debug printfs, very slow
2142#
2143# DRM requires AGP in the kernel.
2144
2145device drm
86689d3d 2146#device "i915kmsdrm" # breaks VGA console, disabled by default
f3d5536d 2147#device radeonkmsdrm # breaks VGA console, disabled by default
745b8439
SW
2148
2149options DRM_DEBUG
2150options DRM_LINUX
2151
2152#
2153# Misc devices
2154#
2155device cmx # Omnikey CardMan 4040 smartcard reader
21e876fb 2156device amdsbwd # AMD South Bridge watchdog
745b8439 2157device gpio # Enable support for the gpio framework
ace1ab86 2158device ichwd # Intel ICH watchdog interrupt timer
ea2c6782 2159device tbridge # regression testing
745b8439 2160
c3a6e36f
SW
2161#
2162# Virtio support
2163#
2164device virtio
2165device virtio_blk
faa875a4 2166device vtnet
c3a6e36f
SW
2167device virtio_pci
2168
745b8439
SW
2169#
2170# Embedded system options:
2171#
2172# An embedded system might want to run something other than init.
2173options INIT_PATH="/sbin/init:/sbin/oinit"
2174
2175# Debug options
2176options BUS_DEBUG # enable newbus debugging
2177options RSS_DEBUG # enable RSS (Receive Side Scaling) debugging
2178
2179# Record the program counter of the code interrupted by the statistics
2180# clock interrupt. Use pctrack(8) to dump this information.
2181options DEBUG_PCTRACK
2182
2183# More undocumented options for linting.
2184# Note that documenting these are not considered an affront.
2185
2186#options ACPI_NO_SEMAPHORES
2187options AHC_DUMP_EEPROM
2188#options BKTR_ALLOC_PAGES=xxx
2189options CAM_DEBUG_DELAY
2190options CLUSTERDEBUG
2191#options COMPAT_LINUX
745b8439
SW
2192options DEBUG
2193options DEBUG_CRIT_SECTIONS
2194options DEBUG_INTERRUPTS
2195#options DISABLE_PSE
b42386ee
SZ
2196options BCE_RSS_DEBUG
2197options BCE_TSS_DEBUG
695a8586 2198options BNX_RSS_DEBUG
69647051 2199options BNX_TSO_DEBUG
695a8586 2200options BNX_TSS_DEBUG
745b8439 2201options EMX_RSS_DEBUG
0c0e1638 2202options EMX_TSO_DEBUG
d84018e9 2203options EMX_TSS_DEBUG
745b8439 2204options JME_RSS_DEBUG
8d6600da 2205options IGB_RSS_DEBUG
4e19e38a 2206options IGB_TSS_DEBUG
9c0ecdcc 2207options IGB_MSIX_DEBUG
0e5f28e9 2208options IX_RSS_DEBUG
745b8439
SW
2209#options ED_NO_MIIBUS
2210options ENABLE_ALART
2211options FB_DEBUG=2
2212options FB_INSTALL_CDEV
745b8439
SW
2213options I586_PMC_GUPROF=0x70000
2214#options IEEE80211_DEBUG_REFCNT
2215options IEEE80211_SUPPORT_SUPERG
2216options KBDIO_DEBUG=10
2217options KBD_MAXRETRY=4
2218options KBD_MAXWAIT=6
2219options KBD_RESETDELAY=201
2220#options KERN_TIMESTAMP
2221options KEY
2222#options LINPROCFS
2223options LOCKF_DEBUG
745b8439
SW
2224#options MAXFILES=xxx
2225options MBUF_DEBUG
ad67a470 2226options NO_LWKT_SPLIT_USERPRI
745b8439
SW
2227options PANIC_DEBUG
2228options PMAP_DEBUG
2229options PSM_DEBUG=4
2230options SCSI_NCR_DEBUG
2231options SCSI_NCR_MAX_SYNC=10000
2232options SCSI_NCR_MAX_WIDE=1
2233options SCSI_NCR_MYADDR=7
2234options SHOW_BUSYBUFS # List buffers that prevent root unmount
2235options SI_DEBUG
603198e6 2236options SLAB_DEBUG
745b8439
SW
2237options SLIP_IFF_OPTS
2238options SOCKBUF_DEBUG
2239options TDMA_BINTVAL_DEFAULT=5
2240options TDMA_SLOTCNT_DEFAULT=2
2241options TDMA_SLOTLEN_DEFAULT=10*1000
2242options TDMA_TXRATE_11A_DEFAULT=2*24
2243options TDMA_TXRATE_11B_DEFAULT=2*11
2244options TDMA_TXRATE_11G_DEFAULT=2*24
2245options TDMA_TXRATE_11NA_DEFAULT="(4|IEEE80211_RATE_MCS)"
2246options TDMA_TXRATE_11NG_DEFAULT="(4|IEEE80211_RATE_MCS)"
2247options TDMA_TXRATE_HALF_DEFAULT=2*12
2248options TDMA_TXRATE_QUARTER_DEFAULT=2*6
2249options TDMA_TXRATE_TURBO_DEFAULT=2*24
2250#options TIMER_FREQ="((14318182+6)/12)"
2251options VFS_BIO_DEBUG
603198e6 2252options VM_PAGE_DEBUG
745b8439
SW
2253options XBONEHACK
2254
2255options KTR
243308a2
SW
2256options KTR_ALL
2257options KTR_ENTRIES=1024
2258options KTR_VERBOSE=1
6836e2b4 2259#options KTR_ACPI_EC
745b8439 2260#options KTR_CTXSW
243308a2 2261#options KTR_DMCRYPT
d912a10e 2262#options KTR_DSCHED_BFQ
745b8439
SW
2263#options KTR_ETHERNET
2264#options KTR_HAMMER
243308a2 2265#options KTR_IFQ
745b8439
SW
2266#options KTR_IF_BGE
2267#options KTR_IF_EM
2268#options KTR_IF_EMX
0e108e8b 2269#options KTR_IF_POLL
745b8439 2270#options KTR_IF_START
745b8439
SW
2271#options KTR_IPIQ
2272#options KTR_KERNENTRY
2273#options KTR_MEMORY
745b8439
SW
2274#options KTR_SERIALIZER
2275#options KTR_SPIN_CONTENTION
2276#options KTR_TESTLOG
2277#options KTR_TOKENS
95a12b8b 2278#options KTR_TSLEEP
6d688f9b 2279#options KTR_UDP
745b8439 2280#options KTR_USB_MEMORY
d6d39bc7 2281#options KTR_USCHED_BSD4
d84d3f48 2282#options KTR_USCHED_DFLY
745b8439
SW
2283
2284# ALTQ
2285options ALTQ #alternate queueing
2286options ALTQ_CBQ #class based queueing
2287options ALTQ_RED #random early detection
2288options ALTQ_RIO #triple red for diffserv (needs RED)
2289options ALTQ_HFSC #hierarchical fair service curve
2290options ALTQ_PRIQ #priority queue
2291options ALTQ_FAIRQ #fair queue
2292#options ALTQ_NOPCC #don't use processor cycle counter
2293options ALTQ_DEBUG #for debugging
2294# you might want to set kernel timer to 1kHz if you use CBQ,
2295# especially with 100baseT
2296#options HZ=1000
2297
2298# SCTP
2299options SCTP
2300options SCTP_DEBUG
2301options SCTP_USE_ADLER32
2302options SCTP_HIGH_SPEED
2303options SCTP_STAT_LOGGING
2304options SCTP_CWND_LOGGING
2305options SCTP_BLK_LOGGING
2306options SCTP_STR_LOGGING
2307options SCTP_FR_LOGGING
2308options SCTP_MAP_LOGGING
2309
2310# DSCHED stuff
b3fc94f8
SW
2311options DSCHED_AS
2312options DSCHED_BFQ
745b8439
SW
2313options DSCHED_FQ
2314
2315# WATCHDOG
745b8439
SW
2316options WDOG_DISABLE_ON_PANIC # Automatically disable watchdogs on panic
2317
2318# LED
2319options ERROR_LED_ON_PANIC # If an error led is present, light it up on panic