aic(4): Remove ISA attachment.
[dragonfly.git] / sys / config / LINT64
CommitLineData
745b8439
SW
1#
2# X86_64_LINT -- config file for checking all the sources, tries to pull in
3# as much of the source tree as it can.
4#
5# $FreeBSD: src/sys/i386/conf/LINT,v 1.749.2.144 2003/06/04 17:56:59 sam Exp $
6#
7# See the kernconf(5) manual page for more information on the format of
8# this file.
9#
10# NB: You probably don't want to try running a kernel built from this
11# file. Instead, you should start from X86_64_GENERIC, and add options
12# from this file as required.
13#
14
15# These directives are mandatory. The machine directive specifies the
16# platform and the machine_arch directive specifies the cpu architecture.
17#
18platform pc64
19machine x86_64
20machine_arch x86_64
21
22#
23# This is the ``identification'' of the kernel. Usually this should
24# be the same as the name of your kernel.
25#
26ident X86_64_LINT
27
28#
29# The `maxusers' parameter controls the static sizing of a number of
30# internal system tables by a formula defined in subr_param.c. Setting
31# maxusers to 0 will cause the system to auto-size based on physical
32# memory.
33#
34maxusers 10
35
36#
37# The `makeoptions' parameter allows variables to be passed to the
38# generated Makefile in the build area.
39#
40# CONF_CFLAGS gives some extra compiler flags that are added to ${CFLAGS}
41# after most other flags. Here we use it to inhibit use of non-optimal
42# gcc builtin functions (e.g., memcmp).
43#
44# DEBUG happens to be magic.
45# The following is equivalent to 'config -g KERNELNAME' and creates
46# 'kernel.debug' compiled with -g debugging as well as a normal
47# 'kernel'. Use 'make install.debug' to install the debug kernel
48# but that isn't normally necessary as the debug symbols are not loaded
49# by the kernel and are not useful there anyway.
50#
51# KERNEL can be overridden so that you can change the default name of your
52# kernel.
53#
54# MODULES_OVERRIDE can be used to limit modules built to a specific list.
55#
56# INSTALLSTRIPPED can be set to cause installkernel to install stripped
57# kernels and modules rather than a kernel and modules with debug symbols.
58#
59# INSTALLSTRIPPEDMODULES can be set to allow a full debug kernel to be
60# installed, but to strip the installed modules.
61#
62makeoptions CONF_CFLAGS=-fno-builtin #Don't allow use of memcmp, etc.
63#makeoptions DEBUG=-g #Build kernel with gdb(1) debug symbols
64#makeoptions KERNEL=foo #Build kernel "foo" and install "/foo"
65# Only build Linux API modules and plus those parts of the sound system I need.
66#makeoptions MODULES_OVERRIDE="linux sound/snd sound/pcm sound/driver/maestro3"
67#makeoptions INSTALLSTRIPPED=1
68#makeoptions INSTALLSTRIPPEDMODULES=1
69
70#
71# Certain applications can grow to be larger than the 128M limit
72# that DragonFly initially imposes. Below are some options to
73# allow that limit to grow to 256MB, and can be increased further
74# with changing the parameters. MAXDSIZ is the maximum that the
75# limit can be set to, and the DFLDSIZ is the default value for
76# the limit. MAXSSIZ is the maximum that the stack limit can be
77# set to. You might want to set the default lower than the max,
78# and explicitly set the maximum with a shell command for processes
79# that regularly exceed the limit like INND.
80#
81options MAXDSIZ="(256*1024*1024)"
82options MAXSSIZ="(256*1024*1024)"
83options DFLDSIZ="(256*1024*1024)"
84
85#
86# BLKDEV_IOSIZE sets the default block size used in user block
87# device I/O. Note that this value will be overridden by the label
88# when specifying a block device from a label with a non-0
89# partition blocksize. The default is PAGE_SIZE.
90#
91options BLKDEV_IOSIZE=8192
92
745b8439
SW
93# This allows you to actually store this configuration file into
94# the kernel binary itself, where it may be later read by saying:
95# strings -n 3 /kernel | sed -n 's/^___//p' > MYKERNEL
96#
97options INCLUDE_CONFIG_FILE # Include this file in kernel
98
99#
100# The root device and filesystem type can be compiled in;
101# this provides a fallback option if the root device cannot
102# be correctly guessed by the bootstrap code, or an override if
103# the RB_DFLTROOT flag (-r) is specified when booting the kernel.
104#
105options ROOTDEVNAME=\"ufs:da0s2e\"
106
745b8439
SW
107#####################################################################
108# SMP OPTIONS:
109#
e93ca50a
SW
110# SMP enables building of a Symmetric MultiProcessor Kernel. It will
111# boot on both SMP and UP boxes.
745b8439
SW
112#
113# Notes:
114#
115# An SMP kernel will ONLY run on an Intel MP spec. qualified motherboard.
116#
117# Check the 'Rogue SMP hardware' section to see if additional options
118# are required by your hardware.
119#
e93ca50a 120#options SMP # Symmetric MultiProcessor Kernel
745b8439 121
745b8439
SW
122#####################################################################
123# CPU OPTIONS
124
125cpu HAMMER_CPU
126
127#
128# Options for CPU features.
129#
745b8439
SW
130# CPU_DISABLE_SSE disables SSE/MMX2 instructions support.
131#
dbe005bb
SW
132# CPU_ENABLE_EST enables support for Enhanced SpeedStep technology
133# found in Pentium(tm) M processors.
134#
745b8439 135#options CPU_DISABLE_SSE
dbe005bb 136options CPU_ENABLE_EST
ebea24c3 137
745b8439
SW
138#####################################################################
139# COMPATIBILITY OPTIONS
140
141#
142# Implement system calls compatible with 4.3BSD and older versions of
143# FreeBSD. You probably do NOT want to remove this as much current code
144# still relies on the 4.3 emulation.
145#
146options COMPAT_43
147
efba76b4
SW
148# Enable NDIS binary driver support
149options NDISAPI
150device ndis
151
745b8439
SW
152#
153# These three options provide support for System V Interface
154# Definition-style interprocess communication, in the form of shared
155# memory, semaphores, and message queues, respectively.
156#
157# System V shared memory and tunable parameters
158options SYSVSHM # include support for shared memory
745b8439
SW
159options SHMMIN=2 # min shared memory segment size (bytes)
160options SHMMNI=33 # max number of shared memory identifiers
161options SHMSEG=9 # max shared memory segments per process
162
163# System V semaphores and tunable parameters
164options SYSVSEM # include support for semaphores
165options SEMMAP=31 # amount of entries in semaphore map
166options SEMMNI=11 # number of semaphore identifiers in the system
167options SEMMNS=61 # number of semaphores in the system
168options SEMMNU=31 # number of undo structures in the system
169options SEMMSL=61 # max number of semaphores per id
170options SEMOPM=101 # max number of operations per semop call
171options SEMUME=11 # max number of undo entries per process
172
173# System V message queues and tunable parameters
174options SYSVMSG # include support for message queues
175options MSGMNB=2049 # max characters per message queue
176options MSGMNI=41 # max number of message queue identifiers
177options MSGSEG=2049 # max number of message segments in the system
178options MSGSSZ=16 # size of a message segment MUST be power of 2
179options MSGTQL=41 # max amount of messages in the system
180
745b8439
SW
181#####################################################################
182# DEBUGGING OPTIONS
183
184#
185# Enable the kernel debugger.
186#
187options DDB
188
189#
190# Print a stack trace on kernel panic.
191#
192options DDB_TRACE
193
194#
195# Don't drop into DDB for a panic. Intended for unattended operation
196# where you may want to drop to DDB from the console, but still want
197# the machine to recover from a panic
198#
199options DDB_UNATTENDED
200
201#
202# If using GDB remote mode to debug the kernel, there's a non-standard
203# extension to the remote protocol that can be used to use the serial
204# port as both the debugging port and the system console. It's non-
205# standard and you're on your own if you enable it. See also the
206# "remotechat" variables in the DragonFly specific version of gdb.
207#
208options GDB_REMOTE_CHAT
209
210#
211# KTRACE enables the system-call tracing facility ktrace(2).
212#
213options KTRACE #kernel tracing
214
215#
216# The INVARIANTS option is used in a number of source files to enable
217# extra sanity checking of internal structures. This support is not
218# enabled by default because of the extra time it would take to check
219# for these conditions, which can only occur as a result of
220# programming errors.
221#
222options INVARIANTS
223
224#
225# The DIAGNOSTIC option is used to enable extra debugging information
226# from some parts of the kernel. As this makes everything more noisy,
227# it is disabled by default.
228#
229options DIAGNOSTIC
230
231#
232# PERFMON causes the driver for Pentium/Pentium Pro performance counters
233# to be compiled. See perfmon(4) for more information.
234#
235options PERFMON
236
237
238#
239# This option let some drivers co-exist that can't co-exist in a running
240# system. This is used to be able to compile all kernel code in one go for
241# quality assurance purposes (like this file, which the option takes it name
242# from.)
243#
244options COMPILING_LINT
245
246
247# XXX - this doesn't belong here.
248# Allow ordinary users to take the console - this is useful for X.
249options UCONSOLE
250
745b8439
SW
251#####################################################################
252# NETWORKING OPTIONS
253
254#
255# Protocol families:
256# Only the INET (Internet) family is officially supported in DragonFly.
257# Source code for the NS (Xerox Network Service) is provided for amusement
258# value.
259#
260options INET #Internet communications protocols
261options INET6 #IPv6 communications protocols
262options IPSEC #IP security
263options IPSEC_ESP #IP security (crypto; define w/ IPSEC)
264options IPSEC_DEBUG #debug for IP security
265#
266# Set IPSEC_FILTERGIF to force packets coming through a gif tunnel
d912a10e 267# to be processed by any configured packet filtering (ipfw).
745b8439
SW
268# The default is that packets coming from a tunnel are _not_ processed;
269# they are assumed trusted.
270#
271# Note that enabling this can be problematic as there are no mechanisms
272# in place for distinguishing packets coming out of a tunnel (e.g. no
273# encX devices as found on openbsd).
274#
275#options IPSEC_FILTERGIF #filter ipsec packets from a tunnel
276
277#
278# Experimental IPsec implementation that uses the kernel crypto
279# framework. This cannot be configured together with IPSEC and
280# (currently) supports only IPv4. To use this you must also
281# configure the crypto device (see below). Note that with this
282# you get all the IPsec protocols (e.g. there is no FAST_IPSEC_ESP).
283# IPSEC_DEBUG is used, as above, to configure debugging support
284# within the IPsec protocols.
285#
286#options FAST_IPSEC #new IPsec
287
288options IPX #IPX/SPX communications protocols
289options IPXIP #IPX in IP encapsulation (not available)
290options IPTUNNEL #IP in IPX encapsulation (not available)
291
292options NCP #NetWare Core protocol
293
294options MPLS #Multi-Protocol Label Switching
295
7902ca8c
SW
296#
297# SMB/CIFS requester
298# NETSMB enables support for SMB protocol, it requires LIBMCHAIN and LIBICONV
299# options.
300# NETSMBCRYPTO enables support for encrypted passwords.
301options NETSMB #SMB/CIFS requester
302options NETSMBCRYPTO #encrypted password support for SMB
303
745b8439
SW
304# mchain library. It can be either loaded as KLD or compiled into kernel
305options LIBMCHAIN #mbuf management library
306
307# netgraph(4). Enable the base netgraph code with the NETGRAPH option.
308# Individual node types can be enabled with the corresponding option
309# listed below; however, this is not strictly necessary as netgraph
310# will automatically load the corresponding KLD module if the node type
311# is not already compiled into the kernel. Each type below has a
312# corresponding man page, e.g., ng_async(4).
313options NETGRAPH #netgraph(4) system
314options NETGRAPH_ASYNC
315options NETGRAPH_BPF
316options NETGRAPH_BRIDGE
317options NETGRAPH_CISCO
318options NETGRAPH_ECHO
319options NETGRAPH_EIFACE
320options NETGRAPH_ETHER
321options NETGRAPH_FRAME_RELAY
322options NETGRAPH_HOLE
323options NETGRAPH_IFACE
324options NETGRAPH_KSOCKET
325options NETGRAPH_L2TP
326options NETGRAPH_LMI
327# MPPC compression requires proprietary files (not included)
328#options NETGRAPH_MPPC_COMPRESSION
329options NETGRAPH_MPPC_ENCRYPTION
330options NETGRAPH_ONE2MANY
331options NETGRAPH_PPP
332options NETGRAPH_PPPOE
333options NETGRAPH_PPTPGRE
334options NETGRAPH_RFC1490
335options NETGRAPH_SOCKET
336options NETGRAPH_TEE
337options NETGRAPH_TTY
338options NETGRAPH_UI
339options NETGRAPH_VJC
340
341device mn # Munich32x/Falc54 Nx64kbit/sec cards.
342
343#
344# Network interfaces:
345# The `loop' pseudo-device is MANDATORY when networking is enabled.
346# The `ether' pseudo-device provides generic code to handle
347# Ethernets; it is MANDATORY when a Ethernet device driver is
348# configured.
349# The `sppp' pseudo-device serves a similar role for certain types
350# of synchronous PPP links (like `ar').
351# The `sl' pseudo-device implements the Serial Line IP (SLIP) service.
352# The `ppp' pseudo-device implements the Point-to-Point Protocol.
353# The `bpf' pseudo-device enables the Berkeley Packet Filter. Be
354# aware of the legal and administrative consequences of enabling this
355# option. The number of devices determines the maximum number of
356# simultaneous BPF clients programs runnable.
357# The `disc' pseudo-device implements a minimal network interface,
358# which throws away all packets sent and never receives any. It is
359# included for testing purposes. This shows up as the 'ds' interface.
360# The `tun' pseudo-device implements (user-)ppp and nos-tun
361# The `gif' pseudo-device implements IPv6 over IP4 tunneling,
362# IPv4 over IPv6 tunneling, IPv4 over IPv4 tunneling and
363# IPv6 over IPv6 tunneling.
364# The `gre' device implements two types of IP4 over IP4 tunneling:
365# GRE and MOBILE, as specified in the RFC1701 and RFC2004.
366# The `faith' pseudo-device captures packets sent to it and diverts them
367# to the IPv4/IPv6 translation daemon.
368# The `stf' device implements 6to4 encapsulation.
369# The `ef' pseudo-device provides support for multiple ethernet frame types
370# specified via ETHER_* options. See ef(4) for details.
371#
372# The PPP_BSDCOMP option enables support for compress(1) style entire
373# packet compression, the PPP_DEFLATE is for zlib/gzip style compression.
374# PPP_FILTER enables code for filtering the ppp data stream and selecting
375# events for resetting the demand dial activity timer - requires bpf.
376# See pppd(8) for more details.
377#
378pseudo-device ether #Generic Ethernet
379pseudo-device vlan 1 #VLAN support
380pseudo-device bridge #Bridging support
381pseudo-device sppp #Generic Synchronous PPP
382pseudo-device loop #Network loopback device
383pseudo-device bpf #Berkeley packet filter
384pseudo-device disc #Discard device (ds0, ds1, etc)
385pseudo-device tun #Tunnel driver (ppp(8), nos-tun(8))
386pseudo-device sl 2 #Serial Line IP
387pseudo-device gre #IP over IP tunneling
388pseudo-device ppp 2 #Point-to-point protocol
389options PPP_BSDCOMP #PPP BSD-compress support
390options PPP_DEFLATE #PPP zlib/deflate/gzip support
391options PPP_FILTER #enable bpf filtering (needs bpf)
392
393pseudo-device ef # Multiple ethernet frames support
394options ETHER_II # enable Ethernet_II frame
395options ETHER_8023 # enable Ethernet_802.3 (Novell) frame
396options ETHER_8022 # enable Ethernet_802.2 frame
397options ETHER_SNAP # enable Ethernet_802.2/SNAP frame
398
399# for IPv6
400pseudo-device gif #IPv6 and IPv4 tunneling
401pseudo-device faith 1 #for IPv6 and IPv4 translation
402pseudo-device stf #6to4 IPv6 over IPv4 encapsulation
403
404#
405# Internet family options:
406#
407# MROUTING enables the kernel multicast packet forwarder, which works
408# with mrouted(8).
409#
410# PIM enables Protocol Independent Multicast in the kernel.
411# Requires MROUTING enabled.
412#
413# IPFIREWALL enables support for IP firewall construction, in
414# conjunction with the `ipfw' program. IPFIREWALL_VERBOSE sends
415# logged packets to the system logger. IPFIREWALL_VERBOSE_LIMIT
416# limits the number of times a matching entry can be logged.
417#
418# WARNING: IPFIREWALL defaults to a policy of "deny ip from any to any"
419# and if you do not add other rules during startup to allow access,
420# YOU WILL LOCK YOURSELF OUT. It is suggested that you set firewall_type=open
421# in /etc/rc.conf when first enabling this feature, then refining the
422# firewall rules in /etc/rc.firewall after you've tested that the new kernel
423# feature works properly.
424#
425# IPFIREWALL_DEFAULT_TO_ACCEPT causes the default rule (at boot) to
426# allow everything. Use with care, if a cracker can crash your
427# firewall machine, they can get to your protected machines. However,
428# if you are using it as an as-needed filter for specific problems as
429# they arise, then this may be for you. Changing the default to 'allow'
430# means that you won't get stuck if the kernel and /sbin/ipfw binary get
431# out of sync.
432#
433# IPDIVERT enables the divert IP sockets, used by ``ipfw divert''
434#
435# IPSTEALTH enables code to support stealth forwarding (i.e., forwarding
436# packets without touching the ttl). This can be useful to hide firewalls
437# from traceroute and similar tools.
438#
439# TCPDEBUG is undocumented.
440#
441options MROUTING # Multicast routing
442options PIM # Protocol Independent Multicast
443options IPFIREWALL #firewall
444options IPFIREWALL_DEBUG #debug prints
445options IPFIREWALL_VERBOSE #enable logging to syslogd(8)
745b8439
SW
446options IPFIREWALL_VERBOSE_LIMIT=100 #limit verbosity
447options IPFIREWALL_DEFAULT_TO_ACCEPT #allow everything by default
448options IPV6FIREWALL #firewall for IPv6
449options IPV6FIREWALL_VERBOSE
450options IPV6FIREWALL_VERBOSE_LIMIT=100
451options IPV6FIREWALL_DEFAULT_TO_ACCEPT
452options IPDIVERT #divert sockets
745b8439
SW
453options IPSTEALTH #support for stealth forwarding
454options TCPDEBUG
455
456device pf
457device pflog
458
459#CARP
460pseudo-device carp
461options CARP
462
463# The MBUF_STRESS_TEST option enables options which create
464# various random failures / extreme cases related to mbuf
465# functions. See the mbuf(9) manpage for a list of available
466# test cases.
467options MBUF_STRESS_TEST
468
469# Statically link in accept filters
470options ACCEPT_FILTER_DATA
471options ACCEPT_FILTER_HTTP
472
473# TCP_SIGNATURE adds support for RFC 2385 (TCP-MD5) digests. These are
474# carried in TCP option 19. This option is commonly used to protect
475# TCP sessions (e.g. BGP) where IPSEC is not available nor desirable.
0defa1cf
SZ
476# This is enabled on a per-socket basis using the TCP_SIGNATURE_ENABLE
477# socket option.
745b8439
SW
478# This requires the use of 'device crypto', 'options IPSEC'
479# or 'device cryptodev'.
480options TCP_SIGNATURE #include support for RFC 2385
481
482#
483# TCP_DROP_SYNFIN adds support for ignoring TCP packets with SYN+FIN. This
484# prevents nmap et al. from identifying the TCP/IP stack, but breaks support
485# for RFC1644 extensions and is not recommended for web servers.
486#
487options TCP_DROP_SYNFIN #drop TCP packets with SYN+FIN
488
489# ICMP_BANDLIM enables icmp error response bandwidth limiting. You
490# typically want this option as it will help protect the machine from
491# D.O.S. packet attacks.
492#
493options ICMP_BANDLIM
494
495# DUMMYNET enables the "dummynet" bandwidth limiter. You need
496# IPFIREWALL as well. See the dummynet(4) and ipfw(8) manpages for more info.
497#
498options DUMMYNET
499options DUMMYNET_DEBUG
500
501#
502# ATM (HARP version) options
503#
504# ATM_CORE includes the base ATM functionality code. This must be included
505# for ATM support.
506#
507# ATM_IP includes support for running IP over ATM.
508#
509# At least one (and usually only one) of the following signalling managers
510# must be included (note that all signalling managers include PVC support):
511# ATM_SIGPVC includes support for the PVC-only signalling manager `sigpvc'.
512# ATM_SPANS includes support for the `spans' signalling manager, which runs
513# the FORE Systems's proprietary SPANS signalling protocol.
514# ATM_UNI includes support for the `uni30' and `uni31' signalling managers,
515# which run the ATM Forum UNI 3.x signalling protocols.
516#
517# The `hea' driver provides support for the Efficient Networks, Inc.
518# ENI-155p ATM PCI Adapter.
519#
520# The `hfa' driver provides support for the FORE Systems, Inc.
521# PCA-200E ATM PCI Adapter.
522#
523#options ATM_CORE #core ATM protocol family
524#options ATM_IP #IP over ATM support
525#options ATM_SIGPVC #SIGPVC signalling manager
526#options ATM_SPANS #SPANS signalling manager
527#options ATM_UNI #UNI signalling manager
528#device hea #Efficient ENI-155p ATM PCI
529#device hfa #FORE PCA-200E ATM PCI
530
531# DEVICE_POLLING adds support for mixed interrupt-polling handling
532# of network device drivers, which has significant benefits in terms
533# of robustness to overloads and responsivity, as well as permitting
534# accurate scheduling of the CPU time between kernel network processing
535# and other activities. The drawback is a moderate (up to 1/pollhz seconds)
536# potential increase in response times. See polling(4) for further details.
537#
538options DEVICE_POLLING
539
540# IFPOLL_ENABLE adds hardware queues' based polling
541options IFPOLL_ENABLE
542
745b8439
SW
543#####################################################################
544# FILESYSTEM OPTIONS
545
546#
547# Only the root, /usr, and /tmp filesystems need be statically
548# compiled; everything else will be automatically loaded at mount
549# time. (Exception: the UFS family --- FFS, and MFS ---
550# cannot currently be demand-loaded.) Some people still prefer
551# to statically compile other filesystems as well.
552#
553# NB: The PORTAL and UNION filesystems are known to be
554# buggy, and WILL panic your system if you attempt to do anything with
555# them. They are included here as an incentive for some enterprising
556# soul to sit down and fix them.
557#
558
559# One of these is mandatory:
560options FFS #Fast filesystem
561options MFS #Memory filesystem
562options NFS #Network filesystem
563
564# The rest are optional:
565#options NFS_NOSERVER #Disable the NFS-server code.
566options CD9660 #ISO 9660 filesystem
567options FDESC #File descriptor filesystem
8124268f 568options HAMMER #HAMMER filesystem
745b8439
SW
569options HPFS #OS/2 File system
570options MSDOSFS #MS DOS filesystem
571options NTFS #NT filesystem
572options NULLFS #NULL filesystem
573options NWFS #NetWare filesystem
574options PORTAL #Portal filesystem
575options PROCFS #Process filesystem
ab5617b3 576options PUFFS #Userspace file systems (e.g. ntfs-3g & sshfs)
7902ca8c 577options SMBFS #SMB/CIFS filesystem
745b8439 578options TMPFS #Temporary filesystem
8124268f 579options UDF #UDF filesystem
745b8439
SW
580
581# YYY-DR Till we rework the VOP methods for this filesystem
582#options UNION #Union filesystem
583# The xFS_ROOT options REQUIRE the associated ``options xFS''
584options FFS_ROOT #FFS usable as root device
585options NFS_ROOT #NFS usable as root device
586
587# Soft updates is technique for improving UFS filesystem speed and
588# making abrupt shutdown less risky.
589options SOFTUPDATES
590
591# Directory hashing improves the speed of operations on very large
592# directories at the expense of some memory.
593options UFS_DIRHASH
594
595# Make space in the kernel for a root filesystem on a md device.
596# Define to the number of kilobytes to reserve for the filesystem.
597options MD_ROOT_SIZE=10
598
599# Make the md device a potential root device, either with preloaded
600# images of type mfs_root or md_root.
601options MD_ROOT
602
603# Specify double the default maximum size for malloc(9)-backed md devices.
604options MD_NSECT=40000
605
606# Allow this many swap-devices.
607#
608# In order to manage swap, the system must reserve bitmap space that
609# scales with the largest mounted swap device multiplied by NSWAPDEV,
610# regardless of whether other swap devices exist or not. So it
611# is not a good idea to make this value too large.
612options NSWAPDEV=5
613
614# Disk quotas are supported when this option is enabled.
615options QUOTA #enable disk quotas
616
617# If you are running a machine just as a fileserver for PC and MAC
d22a69a4 618# users, e.g. using SAMBA, you may consider setting this option
745b8439
SW
619# and keeping all those users' directories on a filesystem that is
620# mounted with the suiddir option. This gives new files the same
621# ownership as the directory (similar to group). It's a security hole
622# if you let these users run programs, so confine it to file-servers
623# (but it'll save you lots of headaches in those cases). Root owned
624# directories are exempt and X bits are cleared. The suid bit must be
625# set on the directory as well; see chmod(1) PC owners can't see/set
626# ownerships so they keep getting their toes trodden on. This saves
627# you all the support calls as the filesystem it's used on will act as
628# they expect: "It's my dir so it must be my file".
629#
630options SUIDDIR
631
632# NFS options:
633options NFS_MINATTRTIMO=3 # VREG attrib cache timeout in sec
634options NFS_MAXATTRTIMO=60
635options NFS_MINDIRATTRTIMO=30 # VDIR attrib cache timeout in sec
636options NFS_MAXDIRATTRTIMO=60
637options NFS_GATHERDELAY=10 # Default write gather delay (msec)
638options NFS_UIDHASHSIZ=29 # Tune the size of nfssvc_sock with this
639options NFS_WDELAYHASHSIZ=16 # and with this
640options NFS_MUIDHASHSIZ=63 # Tune the size of nfsmount with this
641options NFS_DEBUG # Enable NFS Debugging
642
643# MSDOSFS options:
644options MSDOSFS_DEBUG # Enable MSDOSFS Debugging
645
646#
647# Add support for the EXT2FS filesystem of Linux fame. Be a bit
648# careful with this - the ext2fs code has a tendency to lag behind
649# changes and not be exercised very much, so mounting read/write could
650# be dangerous (and even mounting read only could result in panics.)
651#
652options EXT2FS
653
654# Optional character code conversion support with LIBICONV.
655# Each option requires their base file system and LIBICONV.
656options CD9660_ICONV
657options MSDOSFS_ICONV
658options NTFS_ICONV
659
745b8439
SW
660#####################################################################
661# POSIX P1003.1B
662
663# Real time extensions added in the 1993 Posix
664# P1003_1B: Infrastructure
665# _KPOSIX_PRIORITY_SCHEDULING: Build in _POSIX_PRIORITY_SCHEDULING
666# _KPOSIX_VERSION: Version kernel is built for
667
668options P1003_1B
669options _KPOSIX_PRIORITY_SCHEDULING
670options _KPOSIX_VERSION=199309L
671
745b8439
SW
672#####################################################################
673# CLOCK OPTIONS
674
675# The granularity of operation is controlled by the kernel option HZ whose
676# default value (100) means a granularity of 10ms (1s/HZ).
677# Consider, however, that reducing the granularity too much might
678# cause excessive overhead in clock interrupt processing,
679# potentially causing ticks to be missed and thus actually reducing
680# the accuracy of operation.
681
682options HZ=100
683
684# The following options are used for debugging clock behavior only, and
685# should not be used for production systems.
686#
687# CLK_CALIBRATION_LOOP will run the clock calibration loop at startup
688# until the user presses a key.
689
690#options CLK_CALIBRATION_LOOP
691
692# The following two options measure the frequency of the corresponding
693# clock relative to the RTC (onboard mc146818a).
694
695#options CLK_USE_I8254_CALIBRATION
696#options CLK_USE_TSC_CALIBRATION
697
745b8439
SW
698#####################################################################
699# SCSI DEVICES
700
701# SCSI DEVICE CONFIGURATION
702
703# The SCSI subsystem consists of the `base' SCSI code, a number of
704# high-level SCSI device `type' drivers, and the low-level host-adapter
705# device drivers. The host adapters are listed in the ISA and PCI
706# device configuration sections below.
707#
708# Beginning with FreeBSD 2.0.5 you can wire down your SCSI devices so
709# that a given bus, target, and LUN always come on line as the same
710# device unit. In earlier versions the unit numbers were assigned
711# in the order that the devices were probed on the SCSI bus. This
712# means that if you removed a disk drive, you may have had to rewrite
713# your /etc/fstab file, and also that you had to be careful when adding
714# a new disk as it may have been probed earlier and moved your device
715# configuration around.
716
717# This old behavior is maintained as the default behavior. The unit
718# assignment begins with the first non-wired down unit for a device
719# type. For example, if you wire a disk as "da3" then the first
720# non-wired disk will be assigned da4.
721
722# The syntax for wiring down devices is:
723
724# device scbus0 at ahc0 # Single bus device
725# device scbus1 at ahc1 bus 0 # Single bus device
726# device scbus3 at ahc2 bus 0 # Twin bus device
727# device scbus2 at ahc2 bus 1 # Twin bus device
728# device da0 at scbus0 target 0 unit 0
729# device da1 at scbus3 target 1
730# device da2 at scbus2 target 3
731# device sa1 at scbus1 target 6
732# device cd
733
734# "units" (SCSI logical unit number) that are not specified are
735# treated as if specified as LUN 0.
736
737# All SCSI devices allocate as many units as are required.
738
739# The "unknown" device (uk? in pre-2.0.5) is now part of the base SCSI
740# configuration and doesn't have to be explicitly configured.
741
742device scbus #base SCSI code
743device ch #SCSI media changers
744device da #SCSI direct access devices (aka disks)
745device sa #SCSI tapes
746device cd #SCSI CD-ROMs
747device pass #CAM passthrough driver
748device sg #Passthrough device (linux scsi generic)
749device pt #SCSI processor type
750device ses #SCSI SES/SAF-TE driver
751
752# Options for device mapper
753device dm
754device dm_target_crypt
755device dm_target_linear
756device dm_target_striped
757
758# Options for iSCSI
759device iscsi_initiator
760options ISCSI_INITIATOR_DEBUG=8
761
762# CAM OPTIONS:
763# debugging options:
764# -- NOTE -- If you specify one of the bus/target/lun options, you must
765# specify them all!
766# CAMDEBUG: When defined enables debugging macros
767# CAM_DEBUG_BUS: Debug the given bus. Use -1 to debug all busses.
768# CAM_DEBUG_TARGET: Debug the given target. Use -1 to debug all targets.
769# CAM_DEBUG_LUN: Debug the given lun. Use -1 to debug all luns.
770# CAM_DEBUG_FLAGS: OR together CAM_DEBUG_INFO, CAM_DEBUG_TRACE,
771# CAM_DEBUG_SUBTRACE, and CAM_DEBUG_CDB
772#
773# CAM_MAX_HIGHPOWER: Maximum number of concurrent high power (start unit) cmds
774# SCSI_NO_SENSE_STRINGS: When defined disables sense descriptions
775# SCSI_NO_OP_STRINGS: When defined disables opcode descriptions
776# SCSI_DELAY: The number of MILLISECONDS to freeze the SIM (scsi adapter)
777# queue after a bus reset, and the number of milliseconds to
778# freeze the device queue after a bus device reset. This
779# can be changed at boot and runtime with the
780# kern.cam.scsi_delay tunable/sysctl.
781options CAMDEBUG
782options CAM_DEBUG_BUS=-1
783options CAM_DEBUG_TARGET=-1
784options CAM_DEBUG_LUN=-1
785options CAM_DEBUG_FLAGS="CAM_DEBUG_INFO|CAM_DEBUG_TRACE|CAM_DEBUG_CDB"
786options CAM_MAX_HIGHPOWER=4
787options SCSI_NO_SENSE_STRINGS
788options SCSI_NO_OP_STRINGS
789options SCSI_DELAY=8000 # Be pessimistic about Joe SCSI device
790
791# Options for the CAM CDROM driver:
792# CHANGER_MIN_BUSY_SECONDS: Guaranteed minimum time quantum for a changer LUN
793# CHANGER_MAX_BUSY_SECONDS: Maximum time quantum per changer LUN, only
794# enforced if there is I/O waiting for another LUN
795# The compiled in defaults for these variables are 2 and 10 seconds,
796# respectively.
797#
798# These can also be changed on the fly with the following sysctl variables:
799# kern.cam.cd.changer.min_busy_seconds
800# kern.cam.cd.changer.max_busy_seconds
801#
802options CHANGER_MIN_BUSY_SECONDS=2
803options CHANGER_MAX_BUSY_SECONDS=10
804
805# Options for the CAM sequential access driver:
806# SA_IO_TIMEOUT: Timeout for read/write/wfm operations, in minutes
807# SA_SPACE_TIMEOUT: Timeout for space operations, in minutes
808# SA_REWIND_TIMEOUT: Timeout for rewind operations, in minutes
809# SA_ERASE_TIMEOUT: Timeout for erase operations, in minutes
810# SA_1FM_AT_EOD: Default to model which only has a default one filemark at EOT.
811options SA_IO_TIMEOUT="(4)"
812options SA_SPACE_TIMEOUT="(60)"
813options SA_REWIND_TIMEOUT="(2*60)"
814options SA_ERASE_TIMEOUT="(4*60)"
815options SA_1FM_AT_EOD
816
817# Optional timeout for the CAM processor target (pt) device
818# This is specified in seconds. The default is 60 seconds.
819options SCSI_PT_DEFAULT_TIMEOUT="60"
820
821# Optional enable of doing SES passthrough on other devices (e.g., disks)
822#
823# Normally disabled because a lot of newer SCSI disks report themselves
824# as having SES capabilities, but this can then clot up attempts to build
825# build a topology with the SES device that's on the box these drives
826# are in....
827options SES_ENABLE_PASSTHROUGH
828
745b8439
SW
829#####################################################################
830# MISCELLANEOUS DEVICES AND OPTIONS
831
832# The `pty' device usually turns out to be ``effectively mandatory'',
833# as it is required for `telnetd', `rlogind', `screen', `emacs', and
834# `xterm', among others.
835
836pseudo-device pty #Pseudo ttys
837pseudo-device gzip #Exec gzipped a.out's
838pseudo-device vn #Vnode driver (turns a file into a device)
839pseudo-device md #Memory/malloc disk
ab5617b3 840pseudo-device putter #for puffs and pud
745b8439
SW
841pseudo-device snp #Snoop device - to look at pty/vty/etc..
842pseudo-device ccd 4 #Concatenated disk driver
843
844# Configuring Vinum into the kernel is not necessary, since the kld
845# module gets started automatically when vinum(8) starts. This
846# device is also untested. Use at your own risk.
847#
848# The option VINUMDEBUG must match the value set in CFLAGS
849# in src/sbin/vinum/Makefile. Failure to do so will result in
850# the following message from vinum(8):
851#
852# Can't get vinum config: Invalid argument
853#
854# see vinum(4) for more reasons not to use these options.
10de45eb 855pseudo-device vinum #Vinum concat/mirror/raid driver
745b8439
SW
856#options VINUMDEBUG #enable Vinum debugging hooks
857
858# Kernel side iconv library
859options LIBICONV
860
861# Size of the kernel message buffer. Should be N * pagesize.
862options MSGBUF_SIZE=40960
863
745b8439
SW
864#####################################################################
865# HARDWARE DEVICE CONFIGURATION
866
867# ISA devices:
868
869#
870# Mandatory ISA devices: isa
871#
872device isa
873
874#
875# Options for `isa':
876#
877# AUTO_EOI_1 enables the `automatic EOI' feature for the master 8259A
878# interrupt controller. This saves about 0.7-1.25 usec for each interrupt.
879# This option breaks suspend/resume on some portables.
880#
881# AUTO_EOI_2 enables the `automatic EOI' feature for the slave 8259A
882# interrupt controller. This saves about 0.7-1.25 usec for each interrupt.
883# Automatic EOI is documented not to work for for the slave with the
884# original i8259A, but it works for some clones and some integrated
885# versions.
886#
887# MAXMEM specifies the amount of RAM on the machine; if this is not
888# specified, DragonFly will first read the amount of memory from the CMOS
889# RAM, so the amount of memory will initially be limited to 64MB or 16MB
890# depending on the BIOS. If the BIOS reports 64MB, a memory probe will
891# then attempt to detect the installed amount of RAM. If this probe
892# fails to detect >64MB RAM you will have to use the MAXMEM option.
893# The amount is in kilobytes, so for a machine with 128MB of RAM, it would
894# be 131072 (128 * 1024).
895#
896# BROKEN_KEYBOARD_RESET disables the use of the keyboard controller to
897# reset the CPU for reboot. This is needed on some systems with broken
898# keyboard controllers.
899
900options AUTO_EOI_1
901#options AUTO_EOI_2
902options MAXMEM="(128*1024)"
903#options BROKEN_KEYBOARD_RESET
904
905# Enable support for the kernel PLL to use an external PPS signal,
906# under supervision of [x]ntpd(8)
907# More info in ntpd documentation: http://www.eecis.udel.edu/~ntp
908
909options PPS_SYNC
910
911# The keyboard controller; it controls the keyboard and the PS/2 mouse.
912device atkbdc0 at isa? port IO_KBD
913
914# The AT keyboard
915device atkbd0 at atkbdc? irq 1
916
917# Options for atkbd:
918options ATKBD_DFLT_KEYMAP # specify the built-in keymap
919makeoptions ATKBD_DFLT_KEYMAP="jp.106"
920
921# These options are valid for other keyboard drivers as well.
922options KBD_DISABLE_KEYMAP_LOAD # refuse to load a keymap
923options KBD_INSTALL_CDEV # install a CDEV entry in /dev
924
925# `flags' for atkbd:
926# 0x01 Force detection of keyboard, else we always assume a keyboard
927# 0x02 Don't reset keyboard, useful for some newer ThinkPads
928# 0x03 Force detection and avoid reset, might help with certain
929# dockingstations
930# 0x04 Old-style (XT) keyboard support, useful for older ThinkPads
931
932# PS/2 mouse
933device psm0 at atkbdc? irq 12
934
935# Options for psm:
936options PSM_HOOKRESUME #hook the system resume event, useful
937 #for some laptops
938options PSM_RESETAFTERSUSPEND #reset the device at the resume event
939
940device kbdmux # keyboard multiplexer
941
942# The video card driver.
943device vga0 at isa?
944
945# Options for vga:
946# Try the following option if the mouse pointer is not drawn correctly
947# or font does not seem to be loaded properly. May cause flicker on
948# some systems.
949options VGA_ALT_SEQACCESS
950
951options VGA_DEBUG=2 # enable VGA debug output
952
953# If you experience problems switching back to 80x25 (or a derived mode),
954# the following option might help.
955#options VGA_KEEP_POWERON_MODE # use power-on settings for 80x25
956
957# If you can dispense with some vga driver features, you may want to
958# use the following options to save some memory.
959#options VGA_NO_FONT_LOADING # don't save/load font
960#options VGA_NO_MODE_CHANGE # don't change video modes
961
962# The following option probably won't work with the LCD displays.
963options VGA_WIDTH90 # support 90 column modes
964
965# Splash screen at start up! Screen savers require this too.
966pseudo-device splash
967
968# The syscons console driver (sco color console compatible).
969device sc0 at isa?
970options MAXCONS=16 # number of virtual consoles
971options SC_ALT_MOUSE_IMAGE # simplified mouse cursor in text mode
972options SC_DEBUG_LEVEL=5 # enable debug output
973options SC_DFLT_FONT # compile font in
974makeoptions SC_DFLT_FONT=cp850
975options SC_DISABLE_DDBKEY # disable `debug' key
976options SC_DISABLE_REBOOT # disable reboot key sequence
977options SC_HISTORY_SIZE=200 # number of history buffer lines
978options SC_MOUSE_CHAR=0x3 # char code for text mode mouse cursor
979options SC_PIXEL_MODE # add support for the raster text mode
980
981# The following options will let you change the default colors of syscons.
982options SC_NORM_ATTR="(FG_GREEN|BG_BLACK)"
983options SC_NORM_REV_ATTR="(FG_YELLOW|BG_GREEN)"
984options SC_KERNEL_CONS_ATTR="(FG_RED|BG_BLACK)"
985options SC_KERNEL_CONS_REV_ATTR="(FG_BLACK|BG_RED)"
986
987# If you have a two button mouse, you may want to add the following option
988# to use the right button of the mouse to paste text.
989options SC_TWOBUTTON_MOUSE
990
991# You can selectively disable features in syscons.
992#options SC_NO_CUTPASTE
993#options SC_NO_FONT_LOADING
994#options SC_NO_HISTORY
995#options SC_NO_SYSMOUSE
996
997#
c67c071b 998# SCSI host adapters: `bt'
745b8439
SW
999#
1000# adv: All Narrow SCSI bus AdvanSys controllers.
1001# adw: Second Generation AdvanSys controllers including the ADV940UW.
745b8439 1002# ahc: Adaptec 274x/284x/294x
c67c071b 1003# aic: Adaptec 1460
745b8439
SW
1004# bt: Most Buslogic controllers
1005# ncv: NCR 53C500 based SCSI host adapters.
1006# nsp: Workbit Ninja SCSI-3 based PC Card SCSI host adapters.
1007# stg: TMC 18C30, 18C50 based ISA/PC Card SCSI host adapters.
1008#
1009# Note that the order is important in order for Buslogic cards to be
1010# probed correctly.
1011#
1012
1013device bt0 at isa? port IO_BT0
1014device adv0 at isa?
1015device adw
c67c071b 1016device aic
745b8439
SW
1017device ncv
1018device nsp
1019device stg0 at isa? port 0x140 irq 11
1020
1021#
1022# Adaptec FSA RAID controllers, including integrated DELL controller,
1023# the Dell PERC 2/QC and the HP NetRAID-4M
1024#
1025device aac
1026options AAC_DEBUG
1027device aacp # SCSI Passthrough interface (optional, CAM required)
1028
1029#
1030# Compaq Smart RAID, Mylex DAC960 and AMI MegaRAID controllers. Only
1031# one entry is needed; the code will find and configure all supported
1032# controllers.
1033#
1034device ida # Compaq Smart RAID
1035device mlx # Mylex DAC960
1036device amr # AMI MegaRAID
1037device amrp # SCSI Passthrough interface (optional, CAM req.)
1038device mfi # LSI MegaRAID SAS
1039device mfip # LSI MegaRAID SAS passthrough, requires CAM
1040options MFI_DEBUG
1041
1042#
1043# Areca RAID (CAM is required).
1044#
1045device arcmsr # Areca SATA II RAID
1046
1047#
1048# Highpoint RocketRAID 182x.
1049device hptmv
1050
1051#
1052# Highpoint RocketRaid 3xxx series SATA RAID
1053device hptiop
1054
1055#
1056# 3ware ATA RAID
1057#
1058device twe # 3ware ATA RAID
1059device twa # 3ware 9000 series PATA/SATA RAID
1060options TWA_DEBUG=10 # enable debug messages
1061device tws # 3ware 9750 series SATA/SAS RAID
1062
1063#
1064# Promise Supertrack SX6000
1065#
1066#device pst
1067
1068#
1069# IBM ServeRAID
1070#
1071device ips
1072
745b8439
SW
1073# AHCI driver, this will override NATA for AHCI devices,
1074# both drivers may be included.
1075#
1076device ahci
1077
1078# SiI3124/3132 driver
1079#
1080device sili
1081
df75ede4
SW
1082# The 'NATA' driver supports all ATA and ATAPI devices.
1083# You only need one "device nata" for it to find all
1084# PCI ATA/ATAPI devices on modern machines.
1085#
745b8439
SW
1086device nata
1087device natadisk # ATA disk drives
1088device natapicd # ATAPI CD/DVD drives
1089device natapifd # ATAPI floppy drives
1090device natapist # ATAPI tape drives
1091device natapicam # ATAPI CAM layer emulation
1092device nataraid # support for ATA software RAID controllers
1093device natausb # ATA-over-USB support
1094
df75ede4 1095# The following options are valid for the NATA driver:
745b8439
SW
1096#
1097# ATA_STATIC_ID: controller numbering is static (like the old driver)
1098# else the device numbers are dynamically allocated.
1099options ATA_STATIC_ID
1100
745b8439 1101# For older non-PCI systems, these are the lines to use:
df75ede4
SW
1102#
1103#device nata0 at isa? port IO_WD1 irq 14
1104#device nata1 at isa? port IO_WD2 irq 15
745b8439
SW
1105
1106#
1107# Standard floppy disk controllers: `fdc' and `fd'
1108#
1109#device fdc0 at isa? port IO_FD1 irq 6 drq 2
1110#
1111# FDC_DEBUG enables floppy debugging. Since the debug output is huge, you
1112# gotta turn it actually on by setting the variable fd_debug with DDB,
1113# however.
1114#options FDC_DEBUG
1115
1116#device fd0 at fdc0 drive 0
1117#device fd1 at fdc0 drive 1
1118
745b8439
SW
1119#
1120# sio: serial ports (see sio(4))
1121
1122device sio0 at isa? port IO_COM1 flags 0x10 irq 4
1123
1124#
1125# `flags' for serial drivers that support consoles (only for sio now):
1126# 0x10 enable console support for this unit. The other console flags
1127# are ignored unless this is set. Enabling console support does
1128# not make the unit the preferred console - boot with -h or set
1129# the 0x20 flag for that. Currently, at most one unit can have
1130# console support; the first one (in config file order) with
1131# this flag set is preferred. Setting this flag for sio0 gives
1132# the old behaviour.
1133# 0x20 force this unit to be the console (unless there is another
1134# higher priority console). This replaces the COMCONSOLE option.
1135# 0x40 reserve this unit for low level console operations. Do not
1136# access the device in any normal way.
1137# 0x80 use this port for serial line gdb support in ddb.
1138#
1139# PnP `flags' (set via userconfig using pnp x flags y)
1140# 0x1 disable probing of this device. Used to prevent your modem
1141# from being attached as a PnP modem.
1142#
1143
1144# Options for serial drivers that support consoles (only for sio now):
1145options BREAK_TO_DEBUGGER #a BREAK on a comconsole goes to
1146 #DDB, if available.
1147options CONSPEED=115200 # speed for serial console
1148 # (default 9600)
1149
1150# Solaris implements a new BREAK which is initiated by a character
1151# sequence CR ~ ^b which is similar to a familiar pattern used on
1152# Sun servers by the Remote Console.
1153options ALT_BREAK_TO_DEBUGGER
1154
1155# Options for sio:
1156options COM_ESP #code for Hayes ESP
1157options COM_MULTIPORT #code for some cards with shared IRQs
1158
1159# Other flags for sio that aren't documented in the man page.
1160# 0x20000 enable hardware RTS/CTS and larger FIFOs. Only works for
1161# ST16650A-compatible UARTs.
1162
3323f1c7
SW
1163# PCI Universal Communications driver
1164# Supports various single and multi port PCI serial cards. Maybe later
1165# also the parallel ports on combination serial/parallel cards. New cards
1166# can be added in src/sys/dev/misc/puc/pucdata.c.
1167device puc
1168
745b8439 1169#
ad9f8794 1170# Network interfaces: `ed', `ep', `is', `lnc'
745b8439
SW
1171#
1172# cs: IBM Etherjet and other Crystal Semi CS89x0-based adapters
1173# ed: Western Digital and SMC 80xx; Novell NE1000 and NE2000; 3Com 3C503
1174# ep: 3Com 3C509
1175# ex: Intel EtherExpress Pro/10 and other i82595-based adapters
1176# fe: Fujitsu MB86960A/MB86965A Ethernet
745b8439
SW
1177# lnc: Lance/PCnet cards (Isolan, Novell NE2100, NE32-VL, AMD Am7990 & Am79C960)
1178# sbsh: Granch SBNI16 SHDSL modem PCI adapters
1179# wi: Lucent WaveLAN/IEEE 802.11 PCMCIA adapters. Note: this supports both
1180# the PCMCIA and ISA cards: the ISA card is really a PCMCIA to ISA
1181# bridge with a PCMCIA adapter plugged into it.
1182# an: Aironet 4500/4800 802.11 wireless adapters. Supports the PCMCIA,
1183# PCI and ISA varieties.
1184# xe: Xircom/Intel EtherExpress Pro100/16 PC Card ethernet controller.
1185#
1186device cs0 at isa? port 0x300
1187device ed0 at isa? port 0x280 irq 5 iomem 0xd8000
1188device ep
1189device ex
745b8439
SW
1190device lnc0 at isa? port 0x280 irq 10 drq 0
1191device sln
1192device sn0 at isa? port 0x300 irq 10
1193
1194# Wlan support is mandatory for some wireless LAN devices.
1195options IEEE80211_DEBUG #enable debugging msgs
1196options IEEE80211_AMPDU_AGE #age frames in AMPDU reorder q's
1197options IEEE80211_SUPPORT_MESH #enable 802.11s D3.0 support
1198options IEEE80211_SUPPORT_TDMA #enable TDMA support
1199device wlan # 802.11 support
1200device wlan_acl # 802.11 MAC-based access control for AP
1201device wlan_ccmp # 802.11 CCMP support
1202device wlan_tkip # 802.11 TKIP support
1203device wlan_wep # 802.11 WEP support
1204device wlan_xauth # 802.11 WPA or 802.1x authentication for AP
1205device wlan_amrr # 802.11 AMRR TX rate control algorithm
1206device an # Aironet Communications 4500/4800
1207device ath # Atheros AR521x
1208options AH_SUPPORT_AR5416
1209device ath_hal # Atheros Hardware Access Layer
1210#device ath_rate_amrr # Atheros AMRR TX rate control algorithm
1211#device ath_rate_onoe # Atheros Onoe TX rate control algorithm
1212device ath_rate_sample # Atheros Sample TX rate control algorithm
1213options ATH_DEBUG # turn on debugging output (see hw.ath.debug)
1214options ATH_DIAGAPI # diagnostic interface to the HAL
1215options ATH_RXBUF=80 # number of RX buffers to allocate
1216options ATH_TXBUF=400 # number of TX buffers to allocate
1217#device iwl # Intel PRO/Wireless 2100
1218device iwi # Intel PRO/Wireless 2200BG/2915ABG
1219device iwn # Intel WiFi Link 4965/1000/5000/5150/5300/6000/6050
1220device wi # WaveLAN/IEEE, PRISM-II, Spectrum24 802.11DS
1221#device rtw # RealTek 8180
1222#device acx # TI ACX100/ACX111.
1223device xe # Xircom PCMCIA
1224device ral # Ralink Technology 802.11 wireless NIC
1225device wpi
1226
1227# IEEE 802.11 adapter firmware modules
1228
1229# iwifw: Intel PRO/Wireless 2200BG/2225BG/2915ABG firmware
1230# iwnfw: Intel WiFi Link 4965/1000/5000/5150/5300/6000/6050
1231# ralfw: Ralink Technology RT25xx and RT26xx firmware
1232# wpifw: Intel 3945ABG Wireless LAN Controller firmware
1233
1234device iwifw
1235device iwnfw
1236device ralfw
1237device wpifw
1238
1239# Bluetooth Protocols
1240device bluetooth
1241
1242#
1243# ATM related options
1244#
1245# The `en' device provides support for Efficient Networks (ENI)
1246# ENI-155 PCI midway cards, and the Adaptec 155Mbps PCI ATM cards (ANA-59x0).
1247#
1248# atm pseudo-device provides generic atm functions and is required for
1249# atm devices.
1250# NATM enables the netnatm protocol family that can be used to
1251# bypass TCP/IP.
1252#
1253# the current driver supports only PVC operations (no atm-arp, no multicast).
1254# for more details, please read the original documents at
1255# http://www.ccrc.wustl.edu/pub/chuck/tech/bsdatm/bsdatm.html
1256#
1257pseudo-device atm
1258device en
1259options NATM #native ATM
1260
1261# Sound drivers
1262#
1263# The flags of the device tells the device a bit more info about the
1264# device that normally is obtained through the PnP interface.
1265# bit 2..0 secondary DMA channel;
1266# bit 4 set if the board uses two dma channels;
1267# bit 15..8 board type, overrides autodetection; leave it
1268# zero if don't know what to put in (and you don't,
1269# since this is unsupported at the moment...).
1270#
1271# This driver will use the new PnP code if it's available. You might
1272# need PNPBIOS for ISA devices.
1273#
1274# If you have a GUS-MAX card and want to use the CS4231 codec on the
1275# card the drqs for the gus max must be 8 bit (1, 2, or 3).
1276#
1277# If you would like to use the full duplex option on the gus, then define
1278# flags to be the ``read dma channel''.
1279#
1280
1281# Basic sound card support:
1282device pcm
1283# For PnP/PCI sound cards:
1284device "snd_ad1816"
1285device "snd_als4000"
1286device "snd_atiixp"
1287device "snd_cmi"
1288device "snd_cs4281"
1289device "snd_csa"
1290device "snd_ds1"
1291device "snd_emu10k1"
1292device "snd_es137x"
1293device "snd_ess"
1294device "snd_fm801"
b9ad643d 1295device "snd_gusc"
745b8439
SW
1296device "snd_hda"
1297device "snd_ich"
1298device "snd_maestro"
1299device "snd_maestro3"
1300device "snd_mss"
1301device "snd_neomagic"
1302device "snd_sb16"
1303device "snd_sb8"
1304device "snd_sbc"
1305device "snd_solo"
1306device "snd_t4dwave"
1307device "snd_via8233"
1308device "snd_via82c686"
1309device "snd_vibes"
1310# For non-pnp sound cards:
1311device pcm0 at isa? irq 10 drq 1 flags 0x0
1312# USB
1313device "snd_uaudio"
1314
1315#
1316# Miscellaneous hardware:
1317#
1318# bktr: Brooktree bt848/848a/849a/878/879 video capture and TV Tuner board
e147701e 1319# ecc: ECC memory controller
745b8439 1320# joy: joystick
d912a10e 1321# nrp: Comtrol Rocketport(ISA) - single card
745b8439
SW
1322# si: Specialix SI/XIO 4-32 port terminal multiplexor
1323# nmdm: nullmodem terminal driver (see nmdm(4))
1324
1325# Notes on the Comtrol Rocketport driver:
1326#
d912a10e 1327# The exact values used for nrp0 depend on how many boards you have
745b8439
SW
1328# in the system. The manufacturer's sample configs are listed as:
1329#
1330# Comtrol Rocketport ISA single card
d912a10e 1331# device nrp0 at isa? port 0x280
745b8439
SW
1332#
1333# If instead you have two ISA cards, one installed at 0x100 and the
1334# second installed at 0x180, then you should add the following to
1335# your kernel configuration file:
1336#
d912a10e
SW
1337# device nrp0 at isa? port 0x100
1338# device nrp1 at isa? port 0x180
745b8439
SW
1339#
1340# For 4 ISA cards, it might be something like this:
1341#
d912a10e
SW
1342# device nrp0 at isa? port 0x180
1343# device nrp1 at isa? port 0x100
1344# device nrp2 at isa? port 0x340
1345# device nrp3 at isa? port 0x240
745b8439
SW
1346#
1347# And for PCI cards, you only need say:
1348#
d912a10e 1349# device nrp
745b8439
SW
1350
1351# Notes on the Specialix SI/XIO driver:
1352# **This is NOT a Specialix supported Driver!**
1353# The host card is memory, not IO mapped.
1354# The Rev 1 host cards use a 64K chunk, on a 32K boundary.
1355# The Rev 2 host cards use a 32K chunk, on a 32K boundary.
1356# The cards can use an IRQ of 11, 12 or 15.
1357
e147701e 1358device ecc
745b8439
SW
1359device joy0 at isa? port IO_GAME
1360device nrp
745b8439
SW
1361device si0 at isa? iomem 0xd0000 irq 12
1362# nullmodem terminal driver
1363device nmdm
1364
1365# The `ahc' device provides support for the Adaptec 274X and 284X
1366# adapters.
1367device ahc
1368
1369# The aic7xxx driver will attempt to use memory mapped I/O for all PCI
1370# controllers that have it configured only if this option is set. Unfortunately,
1371# this doesn't work on some motherboards, which prevents it from being the
1372# default.
1373options AHC_ALLOW_MEMIO
1374
1375# The adw driver will attempt to use memory mapped I/O for all PCI
1376# controllers that have it configured only if this option is set.
1377options ADW_ALLOW_MEMIO
1378
1379#
1380# PCI devices & PCI options:
1381#
1382# The main PCI bus device is `pci'. It provides auto-detection and
1383# configuration support for all devices on the PCI bus, using either
1384# configuration mode defined in the PCI specification.
1385
1386device pci
1387
1388# PCI options
1389#
745b8439
SW
1390options COMPAT_OLDPCI #FreeBSD 2.2 and 3.x compatibility shims
1391
1392# AGP GART support
1393#
1394device agp
1395
1396
1397# The `ahc' device provides support for the Adaptec 29/3940(U)(W)
1398# and motherboard based AIC7870/AIC7880 adapters.
1399options AHC_DEBUG
1400options AHC_DEBUG_OPTS=0xffffffff
1401options AHC_REG_PRETTY_PRINT
1402options AHC_TMODE_ENABLE
1403#
1404# The 'ahd' device provides support for the Adaptec 79xx Ultra320
1405# SCSI adapters. Options are documented in the ahd(4) manpage:
1406options AHD_DEBUG
1407options AHD_DEBUG_OPTS=0xffffffff
1408options AHD_REG_PRETTY_PRINT
1409#options AHD_TMODE_ENABLE=0xff
1410#
1411# The `amd' device provides support for the AMD 53C974 SCSI host
1412# adapter chip as found on devices such as the Tekram DC-390(T).
1413#
1414# The `bge' device provides support for gigabit ethernet adapters
1415# based on the Broadcom BCM570x family of controllers, including the
1416# 3Com 3c996-T, the Netgear GA302T, the SysKonnect SK-9D21 and SK-9D41,
1417# and the embedded gigE NICs on Dell PowerEdge 2550 servers.
1418#
1419# The `ncr' device provides support for the NCR 53C810 and 53C825
1420# self-contained SCSI host adapters.
1421#
1422# The `isp' device provides support for the Qlogic ISP 1020, 1040
1423# nd 1040B PCI SCSI host adapters, ISP 1240 Dual Ultra SCSI,
1424# ISP 1080 and 1280 (Dual) Ultra2, ISP 12160 Ultra3 SCSI, as well as
1425# the Qlogic ISP 2100 and ISP 2200 Fibre Channel Host Adapters.
1426#
1427# The `dc' device provides support for PCI fast ethernet adapters
1428# based on the DEC/Intel 21143 and various workalikes including:
1429# the ADMtek AL981 Comet and AN985 Centaur, the ASIX Electronics
1430# AX88140A and AX88141, the Davicom DM9100 and DM9102, the Lite-On
1431# 82c168 and 82c169 PNIC, the Lite-On/Macronix LC82C115 PNIC II
1432# and the Macronix 98713/98713A/98715/98715A/98725 PMAC. This driver
1433# replaces the old al, ax, dm, pn and mx drivers. List of brands:
1434# Digital DE500-BA, Kingston KNE100TX, D-Link DFE-570TX, SOHOware SFA110,
1435# SVEC PN102-TX, CNet Pro110B, 120A, and 120B, Compex RL100-TX,
1436# LinkSys LNE100TX, LNE100TX V2.0, Jaton XpressNet, Alfa Inc GFC2204,
1437# KNE110TX.
1438#
1439# The `de' device provides support for the Digital Equipment DC21040
1440# self-contained Ethernet adapter.
1441#
1442# The `em' device provides support for the Intel Pro/1000 Family of Gigabit
1443# adapters (82542, 82543, 82544, 82540).
1444#
1445# The `et' device provides support for the Agere ET1310 10/100/1000 PCIe
1446# adapters.
1447#
1448# The `fxp' device provides support for the Intel EtherExpress Pro/100B
1449# PCI Fast Ethernet adapters.
1450#
1451# The 'lge' device provides support for PCI gigabit ethernet adapters
1452# based on the Level 1 LXT1001 NetCellerator chipset. This includes the
1453# D-Link DGE-500SX, SMC TigerCard 1000 (SMC9462SX), and some Addtron cards.
1454#
1455# The 'my' device provides support for the Myson MTD80X and MTD89X PCI
1456# Fast Ethernet adapters.
1457#
1458# The 'nge' device provides support for PCI gigabit ethernet adapters
1459# based on the National Semiconductor DP83820 and DP83821 chipset. This
1460# includes the SMC EZ Card 1000 (SMC9462TX), D-Link DGE-500T, Asante
1461# FriendlyNet GigaNIX 1000TA and 1000TPC, the Addtron AEG320T, the
1462# LinkSys EG1032 and EG1064, the Surecom EP-320G-TX and the Netgear GA622T.
1463#
1464# The 'pcn' device provides support for PCI fast ethernet adapters based
1465# on the AMD Am79c97x chipsets, including the PCnet/FAST, PCnet/FAST+,
1466# PCnet/PRO and PCnet/Home. These were previously handled by the lnc
1467# driver (and still will be if you leave this driver out of the kernel).
1468#
1469# Te 're' device provides support for PCI GigaBit ethernet adapters based
1470# on the RealTek 8169 chipset. It also supports the 8139C+ and is the
1471# preferred driver for that chip.
1472#
1473# The 'rl' device provides support for PCI fast ethernet adapters based
1474# on the RealTek 8129/8139 chipset. Note that the RealTek driver defaults
1475# to using programmed I/O to do register accesses because memory mapped
1476# mode seems to cause severe lockups on SMP hardware. This driver also
1477# supports the Accton EN1207D `Cheetah' adapter, which uses a chip called
1478# the MPX 5030/5038, which is either a RealTek in disguise or a RealTek
1479# workalike. Note that the D-Link DFE-530TX+ uses the RealTek chipset
1480# and is supported by this driver, not the 'vr' driver.
1481#
1482# The 'sf' device provides support for Adaptec Duralink PCI fast
1483# ethernet adapters based on the Adaptec AIC-6915 "starfire" controller.
1484# This includes dual and quad port cards, as well as one 100baseFX card.
1485# Most of these are 64-bit PCI devices, except for one single port
1486# card which is 32-bit.
1487#
1488# The 'ste' device provides support for adapters based on the Sundance
1489# Technologies ST201 PCI fast ethernet controller. This includes the
1490# D-Link DFE-550TX.
1491#
1492# The 'sis' device provides support for adapters based on the Silicon
1493# Integrated Systems SiS 900 and SiS 7016 PCI fast ethernet controller
1494# chips.
1495#
1496# The 'sk' device provides support for the SysKonnect SK-984x series
1497# PCI gigabit ethernet NICs. This includes the SK-9841 and SK-9842
1498# single port cards (single mode and multimode fiber) and the
1499# SK-9843 and SK-9844 dual port cards (also single mode and multimode).
1500# The driver will autodetect the number of ports on the card and
1501# attach each one as a separate network interface.
1502#
1503# The 'ti' device provides support for PCI gigabit ethernet NICs based
1504# on the Alteon Networks Tigon 1 and Tigon 2 chipsets. This includes the
1505# Alteon AceNIC, the 3Com 3c985, the Netgear GA620 and various others.
1506# Note that you will probably want to bump up NMBCLUSTERS a lot to use
1507# this driver.
1508#
1509# The 'tl' device provides support for the Texas Instruments TNETE100
1510# series 'ThunderLAN' cards and integrated ethernet controllers. This
1511# includes several Compaq Netelligent 10/100 cards and the built-in
1512# ethernet controllers in several Compaq Prosignia, Proliant and
1513# Deskpro systems. It also supports several Olicom 10Mbps and 10/100
1514# boards.
1515#
1516# The `tx' device provides support for the SMC 9432 TX, BTX and FTX cards.
1517#
1518# The `txp' device provides support for the 3Com 3cR990 "Typhoon"
1519# 10/100 adapters.
1520#
1521# The `vr' device provides support for various fast ethernet adapters
1522# based on the VIA Technologies VT3043 `Rhine I' and VT86C100A `Rhine II'
1523# chips, including the D-Link DFE530TX (see 'rl' for DFE530TX+), the Hawking
1524# Technologies PN102TX, and the AOpen/Acer ALN-320.
1525#
1526# The `vx' device provides support for the 3Com 3C590 and 3C595
1527# early support
1528#
1529# The `wb' device provides support for various fast ethernet adapters
1530# based on the Winbond W89C840F chip. Note: this is not the same as
1531# the Winbond W89C940F, which is an NE2000 clone.
1532#
1533# The `xl' device provides support for the 3Com 3c900, 3c905 and
1534# 3c905B (Fast) Etherlink XL cards and integrated controllers. This
1535# includes the integrated 3c905B-TX chips in certain Dell Optiplex and
1536# Dell Precision desktop machines and the integrated 3c905-TX chips
1537# in Dell Latitude laptop docking stations.
1538#
1539# The 'bktr' device is a PCI video capture device using the Brooktree
1540# bt848/bt848a/bt849a/bt878/bt879 chipset. When used with a TV Tuner it forms a
1541# TV card, eg Miro PC/TV, Hauppauge WinCast/TV WinTV, VideoLogic Captivator,
1542# Intel Smart Video III, AverMedia, IMS Turbo, FlyVideo.
1543#
1544# options OVERRIDE_CARD=xxx
1545# options OVERRIDE_TUNER=xxx
1546# options OVERRIDE_MSP=1
1547# options OVERRIDE_DBX=1
1548# These options can be used to override the auto detection
1549# The current values for xxx are found in src/sys/dev/video/bktr/bktr_card.h
1550# Using sysctl(8) run-time overrides on a per-card basis can be made
1551#
1552# options BKTR_SYSTEM_DEFAULT=BROOKTREE_PAL
1553# or
1554# options BKTR_SYSTEM_DEFAULT=BROOKTREE_NTSC
1555# Specifes the default video capture mode.
1556# This is required for Dual Crystal (28&35Mhz) boards where PAL is used
1557# to prevent hangs during initialisation. eg VideoLogic Captivator PCI.
1558#
1559# options BKTR_USE_PLL
1560# PAL or SECAM users who have a 28Mhz crystal (and no 35Mhz crystal)
1561# must enable PLL mode with this option. eg some new Bt878 cards.
1562#
1563# options BKTR_GPIO_ACCESS
1564# This enable IOCTLs which give user level access to the GPIO port.
1565#
1566# options BKTR_NO_MSP_RESET
1567# Prevents the MSP34xx reset. Good if you initialise the MSP in another OS first
1568#
1569# options BKTR_430_FX_MODE
1570# Switch Bt878/879 cards into Intel 430FX chipset compatibility mode.
1571#
1572# options BKTR_SIS_VIA_MODE
1573# Switch Bt878/879 cards into SIS/VIA chipset compatibility mode which is
1574# needed for some old SiS and VIA chipset motherboards.
1575# This also allows Bt878/879 chips to work on old OPTi (<1997) chipset
1576# motherboards and motherboards with bad or incomplete PCI 2.1 support.
1577# As a rough guess, old = before 1998
1578#
1579# options BKTR_NEW_MSP34XX_DRIVER
1580# Use new, more complete initialization scheme for the msp34* soundchip.
1581# Should fix stereo autodetection if the old driver does only output
1582# mono sound.
1583#
1584# options BKTR_OVERRIDE_CARD=xxx
1585# options BKTR_OVERRIDE_DBX=xxx
1586# options BKTR_OVERRIDE_MSP=xxx
1587# options BKTR_OVERRIDE_TUNER=xxx
1588# These options can be used to select a specific device, regardless of
1589# the autodetection and i2c device checks (see comments in bktr_card.c).
1590#
1591device ahc # AHA2940 and onboard AIC7xxx devices
1592device ahd # AIC79xx devices
1593device amd # AMD 53C974 (Tekram DC-390(T))
1594device isp # Qlogic family
1595device ispfw # Firmware for QLogic HBAs
1596device mpt # LSI '909 FC adapters
1597device mps # LSI-Logic MPT-Fusion 2
1598device ncr # NCR/Symbios Logic
1599device sym # NCR/Symbios Logic (newer chipsets)
1600device trm # Tekram DC395U/UW/F and DC315U
1601#
1602# Options for ISP
1603#
1604# ISP_TARGET_MODE - enable target mode operation
1605#options ISP_TARGET_MODE=1
1606
47a69c3f 1607# Options used in dev/disk/sym/ (Symbios SCSI driver).
745b8439
SW
1608#options SYM_SETUP_LP_PROBE_MAP #-Low Priority Probe Map (bits)
1609 # Allows the ncr to take precedence
1610 # 1 (1<<0) -> 810a, 860
1611 # 2 (1<<1) -> 825a, 875, 885, 895
1612 # 4 (1<<2) -> 895a, 896, 1510d
1613#options SYM_SETUP_SCSI_DIFF #-HVD support for 825a, 875, 885
1614 # disabled:0 (default), enabled:1
1615#options SYM_SETUP_PCI_PARITY #-PCI parity checking
1616 # disabled:0, enabled:1 (default)
1617#options SYM_SETUP_MAX_LUN #-Number of LUNs supported
1618 # default:8, range:[1..64]
1619
1620
1621# MII bus support is required for some PCI 10/100 ethernet NICs,
1622# namely those which use MII-compliant transceivers or implement
1623# transceiver control interfaces that operate like an MII. Adding
1624# "device miibus0" to the kernel config pulls in support for
1625# the generic miibus API and all of the PHY drivers, including a
1626# generic one for PHYs that aren't specifically handled by an
1627# individual driver.
1628device miibus
1629
1630# PCI Ethernet NICs that use the common MII bus controller code.
1631device ae # Attansic/Atheros L2 Fast Ethernet
1632device alc # Atheros AR8131/AR8132
1633device ale # Atheros AR8121/AR8113/AR8114
1634device age # Attansic/Atheros L1 Gigabit Ethernet
1635device bce # Broadcom NetXtreme II Gigabit Ethernet
1636device bfe # Broadcom BCM440x 10/100 Ethernet
1637device dc # DEC/Intel 21143 and various workalikes
1638device fxp # Intel EtherExpress PRO/100B (82557, 82558)
1639device my # Myson Fast Ethernet (MTD80X, MTD89X)
1640device pcn # AMD Am79C97x PCI 10/100 NICs
1641device re # RealTek 8139C+/8169
1642device rl # RealTek 8129/8139
1643device sbsh # Granch SBNI16 SHDSL modem
1644device sf # Adaptec AIC-6915 (``Starfire'')
1645device sis # Silicon Integrated Systems SiS 900/SiS 7016
1646device ste # Sundance ST201 (D-Link DFE-550TX)
1647device tl # Texas Instruments ThunderLAN
1648device tx # SMC EtherPower II (83c17x ``EPIC'')
1649device vge # VIA 612x GigE
1650device vr # VIA Rhine, Rhine II
1651device wb # Winbond W89C840F
1652device xl # 3Com 3c90x (``Boomerang'', ``Cyclone'')
1653
1654# PCI Ethernet NICs.
1655device de # DEC/Intel DC21x4x (``Tulip'')
1656device txp # 3Com 3cR990 (``Typhoon'')
1657device vx # 3Com 3c590, 3c595 (``Vortex'')
1658
1659# Gigabit Ethernet NICs.
1660device bge # Broadcom BCM570x (``Tigon III'')
1661device em # Intel Pro/1000 (8254x,8257x)
1662 # Requires ig_hal
1663device emx # Intel Pro/1000 (8257{1,2,3,4})
1664 # Requires ig_hal
1665device ig_hal # Intel Pro/1000 hardware abstraction layer
1666device et # Agere ET1310 10/100/1000 Ethernet
1667device lge # Level 1 LXT1001 (``Mercury'')
1668device mxge # Myricom Myri-10G 10GbE NIC
1669device nfe # nVidia nForce2/3 MCP04/51/55 CK804
1670device nge # NatSemi DP83820 and DP83821
1671device sk # SysKonnect GEnesis, LinkSys EG1023, D-Link
1672device ti # Alteon (``Tigon I'', ``Tigon II'')
1673device stge # Sundance/Tamarack TC9021 Gigabit Ethernet
1674device msk # Marvell/SysKonnect Yukon II Gigabit Ethernet
1675device jme # JMicron Gigabit/Fast Ethernet
1676
1677# Brooktree driver has been ported to the new I2C framework. Thus,
1678# you'll need to have the following 3 lines in the kernel config.
1679# device smbus
1680# device iicbus
1681# device iicbb
1682# The iic and smb devices are only needed if you want to control other
1683# I2C slaves connected to the external connector of some cards.
1684#
1685device bktr
1686options BKTR_NEW_MSP34XX_DRIVER
1687
1688# WinTV PVR-250/350 driver
1689device cxm
1690
1691#
1692# PCCARD/PCMCIA
1693#
1694# pccard: pccard slots
1695# cardbus/cbb: cardbus bridge
1696device pccard
1697device cardbus
1698device cbb
1699
1700# For older notebooks that signal a powerfail condition (external
1701# power supply dropped, or battery state low) by issuing an NMI:
1702
1703options POWERFAIL_NMI # make it beep instead of panicing
1704
1705#
1706# MMC/SD
1707#
1708# mmc MMC/SD bus
1709# mmcsd MMC/SD memory card
1710# sdhci Generic PCI SD Host Controller
1711#
1712device mmc
1713device mmcsd
1714device sdhci
1715
1716#
1717# SMB bus
1718#
1719# System Management Bus support is provided by the 'smbus' device.
1720# Access to the SMBus device is via the 'smb' device (/dev/smb*),
1721# which is a child of the 'smbus' device.
1722#
1723# Supported devices:
1724# smb standard io through /dev/smb*
1725#
1726# Supported SMB interfaces:
1727# iicsmb I2C to SMB bridge with any iicbus interface
1728# bktr brooktree848 I2C hardware interface
1729# intpm Intel PIIX4 (82371AB, 82443MX) Power Management Unit
1730# alpm Acer Aladdin-IV/V/Pro2 Power Management Unit
1731# ichsmb Intel ICH SMBus controller chips (82801AA, 82801AB, 82801BA)
1732# viapm VIA VT82C586B,596,686A and VT8233 SMBus controllers
1733# amdpm AMD 756 Power Management Unit
1734# amdsmb AMD 8111 SMBus 2.0 Controller
1735#
1736device smbus # Bus support, required for smb below.
1737
1738device intpm
1739device alpm
1740device ichsmb
1741device viapm
1742device amdpm
1743device amdsmb
1744
1745device smb
1746
1747#
1748# I2C Bus
1749#
1750# Philips i2c bus support is provided by the `iicbus' device.
1751#
1752# Supported devices:
1753# ic i2c network interface
1754# iic i2c standard io
1755# iicsmb i2c to smb bridge. Allow i2c i/o with smb commands.
1756#
1757# Supported interfaces:
1758# pcf Philips PCF8584 ISA-bus controller
1759# bktr brooktree848 I2C software interface
1760#
1761# Other:
1762# iicbb generic I2C bit-banging code (needed by lpbb, bktr)
1763#
1764device iicbus # Bus support, required for ic/iic/iicsmb below.
1765device iicbb
1766
1767device ic
1768device iic
1769device iicsmb # smb over i2c bridge
1770
1771device pcf0 at isa? port 0x320 irq 5
1772
1773# Intel Core and newer CPUs on-die digital thermal sensor support
1774device coretemp
1775
1776# AMD Family 0Fh, 10h and 11h temperature sensors
1777device kate
1778device km
1779
1780# ThinkPad Active Protection System accelerometer
1781device aps0 at isa? port 0x1600
1782
1783# HW monitoring devices lm(4), it(4) and nsclpcsio.
1784device lm0 at isa? port 0x290
1785device it0 at isa? port 0x290
1786device it1 at isa? port 0xc00
1787device it2 at isa? port 0xd00
1788device it3 at isa? port 0x228
1789device nsclpcsio0 at isa? port 0x2e
1790device nsclpcsio1 at isa? port 0x4e
1791device wbsio0 at isa? port 0x2e
1792device wbsio1 at isa? port 0x4e
1793device lm#3 at wbsio?
1794device uguru0 at isa? port 0xe0 # ABIT uGuru
1795
745b8439
SW
1796# Parallel-Port Bus
1797#
1798# Parallel port bus support is provided by the `ppbus' device.
1799# Multiple devices may be attached to the parallel port, devices
1800# are automatically probed and attached when found.
1801#
1802# Supported devices:
1803# vpo Iomega Zip Drive
1804# Requires SCSI disk support ('scbus' and 'da'); the best
1805# performance is achieved with ports in EPP 1.9 mode.
1806# lpt Parallel Printer
1807# plip Parallel network interface
1808# ppi General-purpose I/O ("Geek Port") + IEEE1284 I/O
1809# pps Pulse per second Timing Interface
1810# lpbb Philips official parallel port I2C bit-banging interface
1811#
1812# Supported interfaces:
1813# ppc ISA-bus parallel port interfaces.
1814#
1815
1816options PPC_PROBE_CHIPSET # Enable chipset specific detection
1817 # (see flags in ppc(4))
1818options DEBUG_1284 # IEEE1284 signaling protocol debug
1819options PERIPH_1284 # Makes your computer act as a IEEE1284
1820 # compliant peripheral
1821options DONTPROBE_1284 # Avoid boot detection of PnP parallel devices
1822options VP0_DEBUG # ZIP/ZIP+ debug
1823options LPT_DEBUG # Printer driver debug
1824options PPC_DEBUG=2 # Parallel chipset level debug
1825options PLIP_DEBUG # Parallel network IP interface debug
1826options PCFCLOCK_VERBOSE # Verbose pcfclock driver
1827options PCFCLOCK_MAX_RETRIES=5 # Maximum read tries (default 10)
1828
1829device ppc0 at isa? irq 7
1830device ppbus
1831device vpo
1832device lpt
1833device plip
1834device ppi
1835device pps
1836device lpbb
1837device pcfclock
1838
1839# Kernel BOOTP support
1840
1841options BOOTP # Use BOOTP to obtain IP address/hostname
1842options BOOTP_NFSROOT # NFS mount root filesystem using BOOTP info
1843options BOOTP_NFSV3 # Use NFS v3 to NFS mount root
1844options BOOTP_COMPAT # Workaround for broken bootp daemons.
1845options BOOTP_WIRED_TO=fxp0 # Use interface fxp0 for BOOTP
1846
1847#
1848# Add tie-ins for a hardware watchdog. This only enable the hooks;
1849# the user must still supply the actual driver.
1850#
1851options HW_WDOG
1852
1853#
1854# Set the number of PV entries per process. Increasing this can
1855# stop panics related to heavy use of shared memory. However, that can
1856# (combined with large amounts of physical memory) cause panics at
1857# boot time due the kernel running out of VM space.
1858#
1859# If you're tweaking this, you might also want to increase the sysctls
1860# "vm.v_free_min", "vm.v_free_reserved", and "vm.v_free_target".
1861#
1862# The value below is the one more than the default.
1863#
1864options PMAP_SHPGPERPROC=201
1865
1866#
1867# Disable swapping. This option removes all code which actually performs
1868# swapping, so it's not possible to turn it back on at run-time.
1869#
1870# This is sometimes usable for systems which don't have any swap space
1871# (see also sysctls "vm.defer_swapspace_pageouts" and
1872# "vm.disable_swapspace_pageouts")
1873#
1874#options NO_SWAPPING
1875
1876# Set the size of the buffer cache KVM reservation, in buffers. This is
1877# scaled by approximately 16384 bytes. The system will auto-size the buffer
1878# cache if this option is not specified.
1879#
1880options NBUF=512
1881
1882# Set the size of the mbuf KVM reservation, in clusters. This is scaled
1883# by approximately 2048 bytes. The system will auto-size the mbuf area
1884# to (512 + maxusers*16) if this option is not specified.
1885# maxusers is in turn computed at boot time depending on available memory
1886# or set to the value specified by "options MAXUSERS=x" (x=0 means
1887# autoscaling).
1888# So, to take advantage of autoscaling, you have to remove both
1889# NMBCLUSTERS and MAXUSERS (and NMBUFS) from your kernel config.
1890#
1891options NMBCLUSTERS=1024
1892
1893# Set the number of mbufs available in the system. Each mbuf
1894# consumes 256 bytes. The system will autosize this (to 4 times
1895# the number of NMBCLUSTERS, depending on other constraints)
1896# if this option is not specified.
1897#
1898options NMBUFS=4096
1899
1900# Tune the buffer cache maximum KVA reservation, in bytes. The maximum is
1901# usually capped at 200 MB, effecting machines with > 1GB of ram. Note
1902# that the buffer cache only really governs write buffering and disk block
1903# translations. The VM page cache is our primary disk cache and is not
1904# effected by the size of the buffer cache.
1905#
1906options VM_BCACHE_SIZE_MAX="(100*1024*1024)"
1907
1908# Tune the swap zone KVA reservation, in bytes. The default is typically
1909# 70 MB, giving the system the ability to manage a maximum of 28GB worth
1910# of swapped out data.
1911#
1912options VM_SWZONE_SIZE_MAX="(50*1024*1024)"
1913
1914#
1915# Enable extra debugging code for locks. This stores the filename and
1916# line of whatever acquired the lock in the lock itself, and change a
1917# number of function calls to pass around the relevant data. This is
1918# not at all useful unless you are debugging lock code. Also note
1919# that it is likely to break e.g. fstat(1) unless you recompile your
1920# userland with -DDEBUG_LOCKS as well.
1921#
9ec899f4
SW
1922# DEBUG_LOCKS_LATENCY adds a sysctl to add a forced latency loop
1923# (count to N) in front of any spinlock or gettoken.
1924#
745b8439 1925options DEBUG_LOCKS
9ec899f4 1926options DEBUG_LOCKS_LATENCY
745b8439
SW
1927
1928# Set the amount of time (in seconds) the system will wait before
1929# rebooting automatically when a kernel panic occurs. If set to (-1),
1930# the system will wait indefinitely until a key is pressed on the
1931# console.
1932options PANIC_REBOOT_WAIT_TIME=16
1933
1934# Attempt to bypass the buffer cache and put data directly into the
1935# userland buffer for read operation when O_DIRECT flag is set on the
1936# file. Both offset and length of the read operation must be
1937# multiples of the physical media sector size.
1938#
1939options DIRECTIO
1940
1941# Specify a lower limit for the number of swap I/O buffers. They are
1942# (among other things) used when bypassing the buffer cache due to
1943# DIRECTIO kernel option enabled and O_DIRECT flag set on file.
1944#
1945#options NSWBUF_MIN=120
1946
1947# The 'asr' driver provides support for current DPT/Adaptec SCSI RAID
1948# controllers (SmartRAID V and VI and later).
1949# These controllers require the CAM infrastructure.
1950#
1951device asr
1952
1953# The 'dpt' driver provides support for DPT controllers (http://www.dpt.com/).
1954# These have hardware RAID-{0,1,5} support, and do multi-initiator I/O.
1955# The DPT controllers are commonly re-licensed under other brand-names -
1956# some controllers by Olivetti, Dec, HP, AT&T, SNI, AST, Alphatronic, NEC and
1957# Compaq are actually DPT controllers.
1958#
1959# See src/sys/dev/raid/dpt for debugging and other subtle options.
1960# DPT_MEASURE_PERFORMANCE Enables a set of (semi)invasive metrics. Various
1961# instruments are enabled. The tools in
1962# /usr/sbin/dpt_* assume these to be enabled.
1963# DPT_HANDLE_TIMEOUTS Normally device timeouts are handled by the DPT.
1964# If you ant the driver to handle timeouts, enable
1965# this option. If your system is very busy, this
1966# option will create more trouble than solve.
1967# DPT_TIMEOUT_FACTOR Used to compute the excessive amount of time to
1968# wait when timing out with the above option.
47a69c3f 1969# DPT_DEBUG_xxxx These are controllable from sys/dev/raid/dpt/dpt.h
745b8439
SW
1970# DPT_LOST_IRQ When enabled, will try, once per second, to catch
1971# any interrupt that got lost. Seems to help in some
1972# DPT-firmware/Motherboard combinations. Minimal
1973# cost, great benefit.
1974# DPT_RESET_HBA Make "reset" actually reset the controller
1975# instead of fudging it. Only enable this if you
1976# are 100% certain you need it.
1977
1978device dpt
1979
1980# DPT options
1981#!CAM# options DPT_MEASURE_PERFORMANCE
1982#!CAM# options DPT_HANDLE_TIMEOUTS
1983options DPT_TIMEOUT_FACTOR=4
1984options DPT_LOST_IRQ
1985options DPT_RESET_HBA
1986
1987#
1988# Compaq "CISS" RAID controllers (SmartRAID 5* series)
1989# These controllers have a SCSI-like interface, and require the
1990# CAM infrastructure.
1991#
1992device ciss
1993
1994#
1995# Intel Integrated RAID controllers.
1996# This driver is supported and maintained by
1997# "Leubner, Achim" <Achim_Leubner@adaptec.com>.
1998#
1999device iir
2000
2001#
2002# Mylex AcceleRAID and eXtremeRAID controllers with v6 and later
2003# firmware. These controllers have a SCSI-like interface, and require
2004# the CAM infrastructure.
2005#
2006device mly
2007
2008# USB support
2009# UHCI controller
2010device uhci
2011# OHCI controller
2012device ohci
2013# EHCI controller
2014device ehci
2015# General USB code (mandatory for USB)
2016device usb
2017#
2018# USB Bluetooth
2019device ubt
2020# Fm Radio
2021device ufm
2022# Generic USB device driver
2023device ugen
2024# Human Interface Device (anything with buttons and dials)
2025device uhid
2026# USB keyboard
2027device ukbd
2028# USB printer
2029device ulpt
2030# USB Iomega Zip 100 Drive (Requires scbus and da)
2031device umass
2032# USB modem support
2033device umodem
2034# USB mouse
2035device ums
2036# USB Rio (MP3 Player)
2037device urio
2038# USB scanners
2039device uscanner
2040# USB com devices
2041device moscom
2042device uark
2043device ubsa
2044device uchcom
2045device ucom
2046device uftdi
2047device ugensa
2048device umct
2049device uplcom
2050device uslcom
2051device uticom
2052device uvisor
2053device uvscom
2054
2055#
2056# ADMtek USB ethernet. Supports the LinkSys USB100TX,
2057# the Billionton USB100, the Melco LU-ATX, the D-Link DSB-650TX
2058# and the SMC 2202USB. Also works with the ADMtek AN986 Pegasus
2059# eval board.
2060device aue
2061#
2062# ASIX Electronics AX88172 USB 2.0 ethernet driver. Used in the
2063# LinkSys USB200M and various other adapters.
2064device axe
2065#
2066# CATC USB-EL1201A USB ethernet. Supports the CATC Netmate
2067# and Netmate II, and the Belkin F5U111.
2068device cue
2069#
2070# Kawasaki LSI ethernet. Supports the LinkSys USB10T,
2071# Entrega USB-NET-E45, Peracom Ethernet Adapter, the
2072# 3Com 3c19250, the ADS Technologies USB-10BT, the ATen UC10T,
2073# the Netgear EA101, the D-Link DSB-650, the SMC 2102USB
2074# and 2104USB, and the Corega USB-T.
2075device kue
2076#
a700a71b
SW
2077# USB CDC ethernet. Supports the LG P-500 smartphone.
2078device lgue
2079#
745b8439
SW
2080# RealTek 8150 based USB ethernet device:
2081# Melco LUA-KTX
2082# GREEN HOUSE GH-USB100B
2083# Billionton ThumbLAN USBKR2-100B
2084device rue
2085
2086# USB wireless NICs, requires wlan_amrr
2087#
2088# Ralink Technology RT2501USB/RT2601USB
2089#device rum
2090#
2091# Ralink Technology RT2500USB
2092#device ural
2093
2094# debugging options for the USB subsystem
2095#
2096options USB_DEBUG
2097
2098# options for ukbd:
2099options UKBD_DFLT_KEYMAP # specify the built-in keymap
2100makeoptions UKBD_DFLT_KEYMAP=it.iso
2101
2102# Firewire support
2103device firewire # Firewire bus code
2104device sbp # SCSI over Firewire (Requires scbus and da)
2105device fwe # Ethernet over Firewire (non-standard!)
2106
2107# dcons support (Dumb Console Device)
2108device dcons # dumb console driver
2109device dcons_crom # FireWire attachment
2110options DCONS_BUF_SIZE=16384 # buffer size
2111options DCONS_POLL_HZ=100 # polling rate
2112options DCONS_FORCE_CONSOLE=1 # force to be the primary console
2113options DCONS_FORCE_GDB=1 # force to be the gdb device
2114
2115#####################################################################
2116# crypto subsystem
2117#
2118# This is a port of the openbsd crypto framework. Include this when
2119# configuring IPsec and when you have a h/w crypto device to accelerate
2120# user applications that link to openssl.
2121#
2122# Drivers are ports from openbsd with some simple enhancements that have
2123# been fed back to openbsd (and hopefully will be included).
2124
2125pseudo-device crypto # core crypto support
2126pseudo-device cryptodev # /dev/crypto for access to h/w
2127
2128device rndtest # FIPS 140-2 entropy tester
2129
2130device hifn # Hifn 7951, 7781, etc.
2131options HIFN_DEBUG # enable debugging support: hw.hifn.debug
2132#options HIFN_NO_RNG # for devices without RNG
2133options HIFN_RNDTEST # enable rndtest support
2134
25638cf4
SW
2135device safe # SafeNet 1141
2136options SAFE_DEBUG # enable debugging support: hw.safe.debug
8690ff8f 2137#options SAFE_NO_RNG # for devices without RNG
25638cf4
SW
2138options SAFE_RNDTEST # enable rndtest support
2139
745b8439
SW
2140device ubsec # Broadcom 5501, 5601, 58xx
2141options UBSEC_DEBUG # enable debugging support: hw.ubsec.debug
2142#options UBSEC_NO_RNG # for devices without RNG
2143options UBSEC_RNDTEST # enable rndtest support
2144
2145device aesni # hardware crypto/RNG for AES-NI
2146device padlock # hardware crypto/RNG for VIA C3/C7/Eden
c5761ad0 2147device rdrand # hardware RNG for RdRand
745b8439
SW
2148
2149#
2150# ACPI support using the Intel ACPI Component Architecture reference
2151# implementation.
2152#
2153# ACPI_DEBUG enables the use of the debug.acpi.level and debug.acpi.layer
2154# kernel environment variables to select initial debugging levels for the
2155# Intel ACPICA code.
2156#
2157# Note that building ACPI into the kernel is deprecated; the module is
2158# normally loaded automatically by the loader.
2159
2160device acpi
2161options ACPI_DEBUG
2162
554257bc
SW
2163# ACPI WMI Mapping driver
2164device acpi_wmi
2165
745b8439
SW
2166# ACPI Asus Extras (LCD backlight/brightness, video output, etc.)
2167device acpi_asus
2168
2169# ACPI Fujitsu Extras (Buttons)
2170device acpi_fujitsu
2171
2172# ACPI extras driver for HP laptops
554257bc 2173device acpi_hp
745b8439
SW
2174
2175# ACPI Panasonic Extras (LCD backlight/brightness, video output, etc.)
2176device acpi_panasonic
2177
2178# ACPI Sony extra (LCD brightness)
2179device acpi_sony
2180
2181# ACPI extras driver for ThinkPad laptops
2182device acpi_thinkpad
2183
2184# ACPI Toshiba Extras (LCD backlight/brightness, video output, etc.)
2185device acpi_toshiba
2186
2187# ACPI Video Extensions (LCD backlight/brightness, video output, etc.)
2188device acpi_video
2189
2190device aibs # ASUSTeK AI Booster (ACPI ASOC ATK0110)
2191
2192# DRM options:
2193# drm: General DRM code
2194# i915drm: Intel i830, i845, i915, i945, i965, G33/35
2195# mach64drm: ATI Mach64 cards - Rage and 3D Rage series
2196# mgadrm: AGP Matrox G200, G400, G450, G550
2197# r128drm: ATI Rage 128 cards
2198# radeondrm: ATI Radeon cards
2199# savagedrm: Savage cards
2200# sisdrm: Sis cards
2201# tdfxdrm: 3dfx Voodoo 3/4/5 and Banshee
2202#
2203# DRM_DEBUG: include debug printfs, very slow
2204#
2205# DRM requires AGP in the kernel.
2206
2207device drm
2208device "i915drm"
2209device "mach64drm"
2210device mgadrm
2211device "r128drm"
2212device radeondrm
2213device savagedrm
2214device sisdrm
2215device tdfxdrm
2216
2217options DRM_DEBUG
2218options DRM_LINUX
2219
2220#
2221# Misc devices
2222#
2223device cmx # Omnikey CardMan 4040 smartcard reader
2224device gpio # Enable support for the gpio framework
ea2c6782 2225device tbridge # regression testing
745b8439
SW
2226
2227#
2228# Embedded system options:
2229#
2230# An embedded system might want to run something other than init.
2231options INIT_PATH="/sbin/init:/sbin/oinit"
2232
2233# Debug options
2234options BUS_DEBUG # enable newbus debugging
2235options RSS_DEBUG # enable RSS (Receive Side Scaling) debugging
2236
2237# Record the program counter of the code interrupted by the statistics
2238# clock interrupt. Use pctrack(8) to dump this information.
2239options DEBUG_PCTRACK
2240
2241# More undocumented options for linting.
2242# Note that documenting these are not considered an affront.
2243
2244#options ACPI_NO_SEMAPHORES
2245options AHC_DUMP_EEPROM
2246#options BKTR_ALLOC_PAGES=xxx
2247options CAM_DEBUG_DELAY
2248options CLUSTERDEBUG
2249#options COMPAT_LINUX
2250options COMPAT_SUNOS
2251options DEBUG
2252options DEBUG_CRIT_SECTIONS
2253options DEBUG_INTERRUPTS
2254#options DISABLE_PSE
2255options BCE_DEBUG
745b8439
SW
2256options EMX_RSS_DEBUG
2257options JME_RSS_DEBUG
2258#options ED_NO_MIIBUS
2259options ENABLE_ALART
2260options FB_DEBUG=2
2261options FB_INSTALL_CDEV
745b8439
SW
2262options I586_PMC_GUPROF=0x70000
2263#options IEEE80211_DEBUG_REFCNT
2264options IEEE80211_SUPPORT_SUPERG
2265options KBDIO_DEBUG=10
2266options KBD_MAXRETRY=4
2267options KBD_MAXWAIT=6
2268options KBD_RESETDELAY=201
2269#options KERN_TIMESTAMP
2270options KEY
2271#options LINPROCFS
2272options LOCKF_DEBUG
745b8439
SW
2273#options MAXFILES=xxx
2274options MBUF_DEBUG
745b8439
SW
2275options PANIC_DEBUG
2276options PMAP_DEBUG
2277options PSM_DEBUG=4
2278options SCSI_NCR_DEBUG
2279options SCSI_NCR_MAX_SYNC=10000
2280options SCSI_NCR_MAX_WIDE=1
2281options SCSI_NCR_MYADDR=7
2282options SHOW_BUSYBUFS # List buffers that prevent root unmount
2283options SI_DEBUG
603198e6 2284options SLAB_DEBUG
745b8439
SW
2285options SLIP_IFF_OPTS
2286options SOCKBUF_DEBUG
2287options TDMA_BINTVAL_DEFAULT=5
2288options TDMA_SLOTCNT_DEFAULT=2
2289options TDMA_SLOTLEN_DEFAULT=10*1000
2290options TDMA_TXRATE_11A_DEFAULT=2*24
2291options TDMA_TXRATE_11B_DEFAULT=2*11
2292options TDMA_TXRATE_11G_DEFAULT=2*24
2293options TDMA_TXRATE_11NA_DEFAULT="(4|IEEE80211_RATE_MCS)"
2294options TDMA_TXRATE_11NG_DEFAULT="(4|IEEE80211_RATE_MCS)"
2295options TDMA_TXRATE_HALF_DEFAULT=2*12
2296options TDMA_TXRATE_QUARTER_DEFAULT=2*6
2297options TDMA_TXRATE_TURBO_DEFAULT=2*24
2298#options TIMER_FREQ="((14318182+6)/12)"
2299options VFS_BIO_DEBUG
603198e6 2300options VM_PAGE_DEBUG
745b8439
SW
2301options XBONEHACK
2302
2303options KTR
243308a2
SW
2304options KTR_ALL
2305options KTR_ENTRIES=1024
2306options KTR_VERBOSE=1
745b8439 2307#options KTR_CTXSW
243308a2 2308#options KTR_DMCRYPT
d912a10e 2309#options KTR_DSCHED_BFQ
745b8439
SW
2310#options KTR_ETHERNET
2311#options KTR_HAMMER
243308a2 2312#options KTR_IFQ
745b8439
SW
2313#options KTR_IF_BGE
2314#options KTR_IF_EM
2315#options KTR_IF_EMX
2316#options KTR_IF_START
745b8439
SW
2317#options KTR_IPIQ
2318#options KTR_KERNENTRY
2319#options KTR_MEMORY
2320#options KTR_POLLING
2321#options KTR_SERIALIZER
2322#options KTR_SPIN_CONTENTION
2323#options KTR_TESTLOG
2324#options KTR_TOKENS
95a12b8b 2325#options KTR_TSLEEP
745b8439 2326#options KTR_USB_MEMORY
745b8439
SW
2327
2328# ALTQ
2329options ALTQ #alternate queueing
2330options ALTQ_CBQ #class based queueing
2331options ALTQ_RED #random early detection
2332options ALTQ_RIO #triple red for diffserv (needs RED)
2333options ALTQ_HFSC #hierarchical fair service curve
2334options ALTQ_PRIQ #priority queue
2335options ALTQ_FAIRQ #fair queue
2336#options ALTQ_NOPCC #don't use processor cycle counter
2337options ALTQ_DEBUG #for debugging
2338# you might want to set kernel timer to 1kHz if you use CBQ,
2339# especially with 100baseT
2340#options HZ=1000
2341
2342# SCTP
2343options SCTP
2344options SCTP_DEBUG
2345options SCTP_USE_ADLER32
2346options SCTP_HIGH_SPEED
2347options SCTP_STAT_LOGGING
2348options SCTP_CWND_LOGGING
2349options SCTP_BLK_LOGGING
2350options SCTP_STR_LOGGING
2351options SCTP_FR_LOGGING
2352options SCTP_MAP_LOGGING
2353
2354# DSCHED stuff
b3fc94f8
SW
2355options DSCHED_AS
2356options DSCHED_BFQ
745b8439
SW
2357options DSCHED_FQ
2358
2359# WATCHDOG
2360options WATCHDOG_ENABLE # Enable watchdog support framework
2361options WDOG_DISABLE_ON_PANIC # Automatically disable watchdogs on panic
2362
2363# LED
2364options ERROR_LED_ON_PANIC # If an error led is present, light it up on panic