2 # LINT -- config file for checking all the sources, tries to pull in
3 # as much of the source tree as it can.
5 # $FreeBSD: src/sys/i386/conf/LINT,v 1.749.2.144 2003/06/04 17:56:59 sam Exp $
7 # See the kernconf(5) manual page for more information on the format of
10 # NB: You probably don't want to try running a kernel built from this
11 # file. Instead, you should start from GENERIC, and add options from
12 # this file as required.
15 # These directives are mandatory. The machine directive specifies the
16 # platform and the machine_arch directive specifies the cpu architecture.
23 # This is the ``identification'' of the kernel. Usually this should
24 # be the same as the name of your kernel.
29 # The `maxusers' parameter controls the static sizing of a number of
30 # internal system tables by a formula defined in subr_param.c. Setting
31 # maxusers to 0 will cause the system to auto-size based on physical
37 # The `makeoptions' parameter allows variables to be passed to the
38 # generated Makefile in the build area.
40 # CONF_CFLAGS gives some extra compiler flags that are added to ${CFLAGS}
41 # after most other flags. Here we use it to inhibit use of non-optimal
42 # gcc builtin functions (e.g., memcmp).
44 # DEBUG happens to be magic.
45 # The following is equivalent to 'config -g KERNELNAME' and creates
46 # 'kernel.debug' compiled with -g debugging as well as a normal
47 # 'kernel'. Use 'make install.debug' to install the debug kernel
48 # but that isn't normally necessary as the debug symbols are not loaded
49 # by the kernel and are not useful there anyway.
51 # KERNEL can be overridden so that you can change the default name of your
54 # MODULES_OVERRIDE can be used to limit modules built to a specific list.
56 # INSTALLSTRIPPED can be set to cause installkernel to install stripped
57 # kernels and modules rather than a kernel and modules with debug symbols.
59 # INSTALLSTRIPPEDMODULES can be set to allow a full debug kernel to be
60 # installed, but to strip the installed modules.
62 makeoptions CONF_CFLAGS=-fno-builtin #Don't allow use of memcmp, etc.
63 #makeoptions DEBUG=-g #Build kernel with gdb(1) debug symbols
64 #makeoptions KERNEL=foo #Build kernel "foo" and install "/foo"
65 # Only build Linux API modules and plus those parts of the sound system I need.
66 #makeoptions MODULES_OVERRIDE="linux sound/snd sound/pcm sound/driver/maestro3"
67 #makeoptions INSTALLSTRIPPED=1
68 #makeoptions INSTALLSTRIPPEDMODULES=1
71 # Certain applications can grow to be larger than the 128M limit
72 # that DragonFly initially imposes. Below are some options to
73 # allow that limit to grow to 256MB, and can be increased further
74 # with changing the parameters. MAXDSIZ is the maximum that the
75 # limit can be set to, and the DFLDSIZ is the default value for
76 # the limit. MAXSSIZ is the maximum that the stack limit can be
77 # set to. You might want to set the default lower than the max,
78 # and explicitly set the maximum with a shell command for processes
79 # that regularly exceed the limit like INND.
81 options MAXDSIZ="(256*1024*1024)"
82 options MAXSSIZ="(256*1024*1024)"
83 options DFLDSIZ="(256*1024*1024)"
86 # BLKDEV_IOSIZE sets the default block size used in user block
87 # device I/O. Note that this value will be overridden by the label
88 # when specifying a block device from a label with a non-0
89 # partition blocksize. The default is PAGE_SIZE.
91 options BLKDEV_IOSIZE=8192
93 # This allows you to actually store this configuration file into
94 # the kernel binary itself, where it may be later read by saying:
95 # strings -n 3 /kernel | sed -n 's/^___//p' > MYKERNEL
97 options INCLUDE_CONFIG_FILE # Include this file in kernel
100 # The root device and filesystem type can be compiled in;
101 # this provides a fallback option if the root device cannot
102 # be correctly guessed by the bootstrap code, or an override if
103 # the RB_DFLTROOT flag (-r) is specified when booting the kernel.
105 options ROOTDEVNAME=\"ufs:da0s2e\"
107 #####################################################################
110 # SMP enables building of a Symmetric MultiProcessor Kernel. It will
111 # boot on both SMP and UP boxes.
115 # An SMP kernel will ONLY run on an Intel MP spec. qualified motherboard.
117 # Be sure to disable 'cpu I486_CPU' for SMP kernels.
119 # Check the 'Rogue SMP hardware' section to see if additional options
120 # are required by your hardware.
122 #options SMP # Symmetric MultiProcessor Kernel
124 #####################################################################
128 # You must specify at least one CPU (the one you intend to run on);
129 # deleting the specification for CPUs you don't need to use may make
130 # parts of the system run faster.
133 cpu I586_CPU # aka Pentium(tm)
134 cpu I686_CPU # aka Pentium Pro(tm)
137 # Options for CPU features.
139 # CPU_ATHLON_SSE_HACK tries to enable SSE instructions when the BIOS has
140 # forgotten to enable them.
142 # CPU_BLUELIGHTNING_FPU_OP_CACHE enables FPU operand cache on IBM
143 # BlueLightning CPU. It works only with Cyrix FPU, and this option
144 # should not be used with Intel FPU.
146 # CPU_BLUELIGHTNING_3X enables triple-clock mode on IBM Blue Lightning
147 # CPU if CPU supports it. The default is double-clock mode on
148 # BlueLightning CPU box.
150 # CPU_BTB_EN enables branch target buffer on Cyrix 5x86 (NOTE 1).
152 # CPU_DIRECT_MAPPED_CACHE sets L1 cache of Cyrix 486DLC CPU in direct
153 # mapped mode. Default is 2-way set associative mode.
155 # CPU_CYRIX_NO_LOCK enables weak locking for the entire address space
156 # of Cyrix 6x86 and 6x86MX CPUs by setting the NO_LOCK bit of CCR1.
157 # Otherwise, the NO_LOCK bit of CCR1 is cleared. (NOTE 3)
159 # CPU_DISABLE_5X86_LSSER disables load store serialize (i.e. enables
160 # reorder). This option should not be used if you use memory mapped
163 # CPU_DISABLE_SSE disables SSE/MMX2 instructions support.
165 # CPU_ENABLE_EST enables support for Enhanced SpeedStep technology
166 # found in Pentium(tm) M processors.
168 # CPU_ENABLE_LONGRUN enables support for Transmeta Crusoe LongRun
169 # technology which allows to restrict power consumption of the CPU by
170 # using group of hw.crusoe.* sysctls.
172 # CPU_ENABLE_TCC enables Thermal Control Circuitry (TCC) found in some
173 # Pentium(tm) 4 and (possibly) later CPUs. When enabled and detected,
174 # TCC supports restricting power consumption using the hw.p4tcc.*
175 # sysctls. This operates independently of SpeedStep and is useful on
176 # systems where other mechanisms such as apm(4) or acpi(4) don't work.
178 # CPU_FASTER_5X86_FPU enables faster FPU exception handler.
180 # CPU_HAS_SSE2 will enable the lfence and mfence instructions in
181 # cpu_lfence() and cpu_mfence(). If the CPU does not support them,
182 # it will cause a panic.
184 # CPU_I486_ON_386 enables CPU cache on i486 based CPU upgrade products
187 # CPU_IORT defines I/O clock delay time (NOTE 1). Default values of
188 # I/O clock delay time on Cyrix 5x86 and 6x86 are 0 and 7,respectively
191 # CPU_L2_LATENCY specified the L2 cache latency value. This option is used
192 # only when CPU_PPRO2CELERON is defined and Mendocino Celeron is detected.
193 # The default value is 5.
195 # CPU_ELAN enables support for AMDs ElanSC520 CPU.
197 # CPU_GEODE enables support for AMD Geode LX, Geode SC1100 and AMD CS5536
199 # CPU_LOOP_EN prevents flushing the prefetch buffer if the destination
200 # of a jump is already present in the prefetch buffer on Cyrix 5x86(NOTE
203 # CPU_PPRO2CELERON enables L2 cache of Mendocino Celeron CPUs. This option
204 # is useful when you use Socket 8 to Socket 370 converter, because most Pentium
205 # Pro BIOSs do not enable L2 cache of Mendocino Celeron CPUs.
207 # CPU_RSTK_EN enables return stack on Cyrix 5x86 (NOTE 1).
209 # CPU_SUSP_HLT enables suspend on HALT. If this option is set, CPU
210 # enters suspend mode following execution of HALT instruction.
212 # CPU_WT_ALLOC enables write allocation on Cyrix 6x86/6x86MX and AMD
215 # CYRIX_CACHE_WORKS enables CPU cache on Cyrix 486 CPUs with cache
216 # flush at hold state.
218 # CYRIX_CACHE_REALLY_WORKS enables (1) CPU cache on Cyrix 486 CPUs
219 # without cache flush at hold state, and (2) write-back CPU cache on
220 # Cyrix 6x86 whose revision < 2.7 (NOTE 2).
222 # NO_F00F_HACK disables the hack that prevents Pentiums (and ONLY
223 # Pentiums) from locking up when a LOCK CMPXCHG8B instruction is
224 # executed. This option is only needed if I586_CPU is also defined,
225 # and should be included for any non-Pentium CPU that defines it.
227 # NO_MEMORY_HOLE is an optimisation for systems with AMD K6 processors
228 # which indicates that the 15-16MB range is *definitely* not being
229 # occupied by an ISA memory hole.
231 # NOTE 1: The CPU_BTB_EN, CPU_IORT, CPU_LOOP_EN and CPU_RSTK_EN options
232 # should not be used because of CPU bugs. They may crash your system.
234 # NOTE 2: If CYRIX_CACHE_REALLY_WORKS is not set, CPU cache is enabled
235 # in write-through mode when revision < 2.7. If revision of Cyrix
236 # 6x86 >= 2.7, CPU cache is always enabled in write-back mode.
238 # NOTE 3: This option may cause failures for software that requires
239 # locked cycles in order to operate correctly.
241 options CPU_ATHLON_SSE_HACK
242 options CPU_BLUELIGHTNING_FPU_OP_CACHE
243 options CPU_BLUELIGHTNING_3X
245 options CPU_CYRIX_NO_LOCK
246 options CPU_DIRECT_MAPPED_CACHE
247 options CPU_DISABLE_5X86_LSSER
248 options CPU_DISABLE_SSE
250 options CPU_ENABLE_EST
251 options CPU_ENABLE_LONGRUN
252 options CPU_ENABLE_TCC
253 options CPU_FASTER_5X86_FPU
256 options CPU_I486_ON_386
258 options CPU_L2_LATENCY=5
260 options CPU_PPRO2CELERON
264 options CYRIX_CACHE_WORKS
265 options CYRIX_CACHE_REALLY_WORKS
266 #options NO_F00F_HACK
267 options NO_MEMORY_HOLE
270 # A math emulator is mandatory if you wish to run on hardware which
271 # does not have a floating-point processor.
272 options MATH_EMULATE #Support for x87 emulation
274 #####################################################################
275 # COMPATIBILITY OPTIONS
278 # Implement system calls compatible with 4.3BSD and older versions of
279 # FreeBSD. You probably do NOT want to remove this as much current code
280 # still relies on the 4.3 emulation.
285 # Implement system calls compatible with DragonFly 1.2 and older.
287 options COMPAT_DF12 #Compatible with DragonFly 1.2 and earlier
289 # Enable NDIS binary driver support
294 # These three options provide support for System V Interface
295 # Definition-style interprocess communication, in the form of shared
296 # memory, semaphores, and message queues, respectively.
298 # System V shared memory and tunable parameters
299 options SYSVSHM # include support for shared memory
300 options SHMMIN=2 # min shared memory segment size (bytes)
301 options SHMMNI=33 # max number of shared memory identifiers
302 options SHMSEG=9 # max shared memory segments per process
304 # System V semaphores and tunable parameters
305 options SYSVSEM # include support for semaphores
306 options SEMMAP=31 # amount of entries in semaphore map
307 options SEMMNI=11 # number of semaphore identifiers in the system
308 options SEMMNS=61 # number of semaphores in the system
309 options SEMMNU=31 # number of undo structures in the system
310 options SEMMSL=61 # max number of semaphores per id
311 options SEMOPM=101 # max number of operations per semop call
312 options SEMUME=11 # max number of undo entries per process
314 # System V message queues and tunable parameters
315 options SYSVMSG # include support for message queues
316 options MSGMNB=2049 # max characters per message queue
317 options MSGMNI=41 # max number of message queue identifiers
318 options MSGSEG=2049 # max number of message segments in the system
319 options MSGSSZ=16 # size of a message segment MUST be power of 2
320 options MSGTQL=41 # max amount of messages in the system
322 #####################################################################
326 # Enable the kernel debugger.
331 # Print a stack trace on kernel panic.
336 # Don't drop into DDB for a panic. Intended for unattended operation
337 # where you may want to drop to DDB from the console, but still want
338 # the machine to recover from a panic
340 options DDB_UNATTENDED
343 # If using GDB remote mode to debug the kernel, there's a non-standard
344 # extension to the remote protocol that can be used to use the serial
345 # port as both the debugging port and the system console. It's non-
346 # standard and you're on your own if you enable it. See also the
347 # "remotechat" variables in the DragonFly specific version of gdb.
349 options GDB_REMOTE_CHAT
352 # KTRACE enables the system-call tracing facility ktrace(2).
354 options KTRACE #kernel tracing
357 # The INVARIANTS option is used in a number of source files to enable
358 # extra sanity checking of internal structures. This support is not
359 # enabled by default because of the extra time it would take to check
360 # for these conditions, which can only occur as a result of
361 # programming errors.
366 # The DIAGNOSTIC option is used to enable extra debugging information
367 # from some parts of the kernel. As this makes everything more noisy,
368 # it is disabled by default.
373 # PERFMON causes the driver for Pentium/Pentium Pro performance counters
374 # to be compiled. See perfmon(4) for more information.
380 # This option let some drivers co-exist that can't co-exist in a running
381 # system. This is used to be able to compile all kernel code in one go for
382 # quality assurance purposes (like this file, which the option takes it name
385 options COMPILING_LINT
388 # XXX - this doesn't belong here.
389 # Allow ordinary users to take the console - this is useful for X.
392 # XXX - this doesn't belong here either
393 options USERCONFIG #boot -c editor
394 options INTRO_USERCONFIG #imply -c and show intro screen
395 options VISUAL_USERCONFIG #visual boot -c editor
397 #####################################################################
402 # Only the INET (Internet) family is officially supported in DragonFly.
403 # Source code for the NS (Xerox Network Service) is provided for amusement
406 options INET #Internet communications protocols
407 options INET6 #IPv6 communications protocols
408 options IPSEC #IP security
409 options IPSEC_ESP #IP security (crypto; define w/ IPSEC)
410 options IPSEC_DEBUG #debug for IP security
412 # Set IPSEC_FILTERGIF to force packets coming through a gif tunnel
413 # to be processed by any configured packet filtering (ipfw).
414 # The default is that packets coming from a tunnel are _not_ processed;
415 # they are assumed trusted.
417 # Note that enabling this can be problematic as there are no mechanisms
418 # in place for distinguishing packets coming out of a tunnel (e.g. no
419 # encX devices as found on openbsd).
421 #options IPSEC_FILTERGIF #filter ipsec packets from a tunnel
424 # Experimental IPsec implementation that uses the kernel crypto
425 # framework. This cannot be configured together with IPSEC and
426 # (currently) supports only IPv4. To use this you must also
427 # configure the crypto device (see below). Note that with this
428 # you get all the IPsec protocols (e.g. there is no FAST_IPSEC_ESP).
429 # IPSEC_DEBUG is used, as above, to configure debugging support
430 # within the IPsec protocols.
432 #options FAST_IPSEC #new IPsec
434 options IPX #IPX/SPX communications protocols
435 options IPXIP #IPX in IP encapsulation (not available)
436 options IPTUNNEL #IP in IPX encapsulation (not available)
438 options NCP #NetWare Core protocol
440 options MPLS #Multi-Protocol Label Switching
444 # NETSMB enables support for SMB protocol, it requires LIBMCHAIN and LIBICONV
446 # NETSMBCRYPTO enables support for encrypted passwords.
447 options NETSMB #SMB/CIFS requester
448 options NETSMBCRYPTO #encrypted password support for SMB
450 # mchain library. It can be either loaded as KLD or compiled into kernel
451 options LIBMCHAIN #mbuf management library
453 # netgraph(4). Enable the base netgraph code with the NETGRAPH option.
454 # Individual node types can be enabled with the corresponding option
455 # listed below; however, this is not strictly necessary as netgraph
456 # will automatically load the corresponding KLD module if the node type
457 # is not already compiled into the kernel. Each type below has a
458 # corresponding man page, e.g., ng_async(4).
459 options NETGRAPH #netgraph(4) system
460 options NETGRAPH_ASYNC
462 options NETGRAPH_BRIDGE
463 options NETGRAPH_CISCO
464 options NETGRAPH_ECHO
465 options NETGRAPH_EIFACE
466 options NETGRAPH_ETHER
467 options NETGRAPH_FRAME_RELAY
468 options NETGRAPH_HOLE
469 options NETGRAPH_IFACE
470 options NETGRAPH_KSOCKET
471 options NETGRAPH_L2TP
473 # MPPC compression requires proprietary files (not included)
474 #options NETGRAPH_MPPC_COMPRESSION
475 options NETGRAPH_MPPC_ENCRYPTION
476 options NETGRAPH_ONE2MANY
478 options NETGRAPH_PPPOE
479 options NETGRAPH_PPTPGRE
480 options NETGRAPH_RFC1490
481 options NETGRAPH_SOCKET
487 device mn # Munich32x/Falc54 Nx64kbit/sec cards.
490 # Network interfaces:
491 # The `loop' pseudo-device is MANDATORY when networking is enabled.
492 # The `ether' pseudo-device provides generic code to handle
493 # Ethernets; it is MANDATORY when a Ethernet device driver is
495 # The `sppp' pseudo-device serves a similar role for certain types
496 # of synchronous PPP links (like `ar').
497 # The `sl' pseudo-device implements the Serial Line IP (SLIP) service.
498 # The `ppp' pseudo-device implements the Point-to-Point Protocol.
499 # The `bpf' pseudo-device enables the Berkeley Packet Filter. Be
500 # aware of the legal and administrative consequences of enabling this
501 # option. The number of devices determines the maximum number of
502 # simultaneous BPF clients programs runnable.
503 # The `disc' pseudo-device implements a minimal network interface,
504 # which throws away all packets sent and never receives any. It is
505 # included for testing purposes. This shows up as the 'ds' interface.
506 # The `tun' pseudo-device implements (user-)ppp and nos-tun
507 # The `gif' pseudo-device implements IPv6 over IP4 tunneling,
508 # IPv4 over IPv6 tunneling, IPv4 over IPv4 tunneling and
509 # IPv6 over IPv6 tunneling.
510 # The `gre' device implements two types of IP4 over IP4 tunneling:
511 # GRE and MOBILE, as specified in the RFC1701 and RFC2004.
512 # The `faith' pseudo-device captures packets sent to it and diverts them
513 # to the IPv4/IPv6 translation daemon.
514 # The `stf' device implements 6to4 encapsulation.
515 # The `ef' pseudo-device provides support for multiple ethernet frame types
516 # specified via ETHER_* options. See ef(4) for details.
518 # The PPP_BSDCOMP option enables support for compress(1) style entire
519 # packet compression, the PPP_DEFLATE is for zlib/gzip style compression.
520 # PPP_FILTER enables code for filtering the ppp data stream and selecting
521 # events for resetting the demand dial activity timer - requires bpf.
522 # See pppd(8) for more details.
524 pseudo-device ether #Generic Ethernet
525 pseudo-device vlan 1 #VLAN support
526 pseudo-device bridge #Bridging support
527 pseudo-device sppp #Generic Synchronous PPP
528 pseudo-device loop #Network loopback device
529 pseudo-device bpf #Berkeley packet filter
530 pseudo-device disc #Discard device (ds0, ds1, etc)
531 pseudo-device tun #Tunnel driver (ppp(8), nos-tun(8))
532 pseudo-device sl 2 #Serial Line IP
533 pseudo-device gre #IP over IP tunneling
534 pseudo-device ppp 2 #Point-to-point protocol
535 options PPP_BSDCOMP #PPP BSD-compress support
536 options PPP_DEFLATE #PPP zlib/deflate/gzip support
537 options PPP_FILTER #enable bpf filtering (needs bpf)
539 pseudo-device ef # Multiple ethernet frames support
540 options ETHER_II # enable Ethernet_II frame
541 options ETHER_8023 # enable Ethernet_802.3 (Novell) frame
542 options ETHER_8022 # enable Ethernet_802.2 frame
543 options ETHER_SNAP # enable Ethernet_802.2/SNAP frame
546 pseudo-device gif #IPv6 and IPv4 tunneling
547 pseudo-device faith 1 #for IPv6 and IPv4 translation
548 pseudo-device stf #6to4 IPv6 over IPv4 encapsulation
551 # Internet family options:
553 # MROUTING enables the kernel multicast packet forwarder, which works
556 # PIM enables Protocol Independent Multicast in the kernel.
557 # Requires MROUTING enabled.
559 # IPFIREWALL enables support for IP firewall construction, in
560 # conjunction with the `ipfw' program. IPFIREWALL_VERBOSE sends
561 # logged packets to the system logger. IPFIREWALL_VERBOSE_LIMIT
562 # limits the number of times a matching entry can be logged.
564 # WARNING: IPFIREWALL defaults to a policy of "deny ip from any to any"
565 # and if you do not add other rules during startup to allow access,
566 # YOU WILL LOCK YOURSELF OUT. It is suggested that you set firewall_type=open
567 # in /etc/rc.conf when first enabling this feature, then refining the
568 # firewall rules in /etc/rc.firewall after you've tested that the new kernel
569 # feature works properly.
571 # IPFIREWALL_DEFAULT_TO_ACCEPT causes the default rule (at boot) to
572 # allow everything. Use with care, if a cracker can crash your
573 # firewall machine, they can get to your protected machines. However,
574 # if you are using it as an as-needed filter for specific problems as
575 # they arise, then this may be for you. Changing the default to 'allow'
576 # means that you won't get stuck if the kernel and /sbin/ipfw binary get
579 # IPDIVERT enables the divert IP sockets, used by ``ipfw divert''
581 # IPSTEALTH enables code to support stealth forwarding (i.e., forwarding
582 # packets without touching the ttl). This can be useful to hide firewalls
583 # from traceroute and similar tools.
585 # TCPDEBUG is undocumented.
587 options MROUTING # Multicast routing
588 options PIM # Protocol Independent Multicast
589 options IPFIREWALL #firewall
590 options IPFIREWALL_DEBUG #debug prints
591 options IPFIREWALL_VERBOSE #enable logging to syslogd(8)
592 options IPFIREWALL_VERBOSE_LIMIT=100 #limit verbosity
593 options IPFIREWALL_DEFAULT_TO_ACCEPT #allow everything by default
594 options IPV6FIREWALL #firewall for IPv6
595 options IPV6FIREWALL_VERBOSE
596 options IPV6FIREWALL_VERBOSE_LIMIT=100
597 options IPV6FIREWALL_DEFAULT_TO_ACCEPT
598 options IPDIVERT #divert sockets
599 options IPSTEALTH #support for stealth forwarding
609 # The MBUF_STRESS_TEST option enables options which create
610 # various random failures / extreme cases related to mbuf
611 # functions. See the mbuf(9) manpage for a list of available
613 options MBUF_STRESS_TEST
615 # Statically link in accept filters
616 options ACCEPT_FILTER_DATA
617 options ACCEPT_FILTER_HTTP
619 # TCP_SIGNATURE adds support for RFC 2385 (TCP-MD5) digests. These are
620 # carried in TCP option 19. This option is commonly used to protect
621 # TCP sessions (e.g. BGP) where IPSEC is not available nor desirable.
622 # This is enabled on a per-socket basis using the TCP_SIGNATURE_ENABLE
624 # This requires the use of 'device crypto', 'options IPSEC'
625 # or 'device cryptodev'.
626 options TCP_SIGNATURE #include support for RFC 2385
629 # TCP_DROP_SYNFIN adds support for ignoring TCP packets with SYN+FIN. This
630 # prevents nmap et al. from identifying the TCP/IP stack, but breaks support
631 # for RFC1644 extensions and is not recommended for web servers.
633 options TCP_DROP_SYNFIN #drop TCP packets with SYN+FIN
635 # ICMP_BANDLIM enables icmp error response bandwidth limiting. You
636 # typically want this option as it will help protect the machine from
637 # D.O.S. packet attacks.
641 # DUMMYNET enables the "dummynet" bandwidth limiter. You need
642 # IPFIREWALL as well. See the dummynet(4) and ipfw(8) manpages for more info.
645 options DUMMYNET_DEBUG
648 # ATM (HARP version) options
650 # ATM_CORE includes the base ATM functionality code. This must be included
653 # ATM_IP includes support for running IP over ATM.
655 # At least one (and usually only one) of the following signalling managers
656 # must be included (note that all signalling managers include PVC support):
657 # ATM_SIGPVC includes support for the PVC-only signalling manager `sigpvc'.
658 # ATM_SPANS includes support for the `spans' signalling manager, which runs
659 # the FORE Systems's proprietary SPANS signalling protocol.
660 # ATM_UNI includes support for the `uni30' and `uni31' signalling managers,
661 # which run the ATM Forum UNI 3.x signalling protocols.
663 # The `hea' driver provides support for the Efficient Networks, Inc.
664 # ENI-155p ATM PCI Adapter.
666 # The `hfa' driver provides support for the FORE Systems, Inc.
667 # PCA-200E ATM PCI Adapter.
669 options ATM_CORE #core ATM protocol family
670 options ATM_IP #IP over ATM support
671 options ATM_SIGPVC #SIGPVC signalling manager
672 options ATM_SPANS #SPANS signalling manager
673 options ATM_UNI #UNI signalling manager
674 device hea #Efficient ENI-155p ATM PCI
675 device hfa #FORE PCA-200E ATM PCI
677 # DEVICE_POLLING adds support for mixed interrupt-polling handling
678 # of network device drivers, which has significant benefits in terms
679 # of robustness to overloads and responsivity, as well as permitting
680 # accurate scheduling of the CPU time between kernel network processing
681 # and other activities. The drawback is a moderate (up to 1/pollhz seconds)
682 # potential increase in response times. See polling(4) for further details.
684 options DEVICE_POLLING
686 # IFPOLL_ENABLE adds hardware queues' based polling
687 options IFPOLL_ENABLE
689 #####################################################################
693 # Only the root, /usr, and /tmp filesystems need be statically
694 # compiled; everything else will be automatically loaded at mount
695 # time. (Exception: the UFS family --- FFS, and MFS ---
696 # cannot currently be demand-loaded.) Some people still prefer
697 # to statically compile other filesystems as well.
699 # NB: The PORTAL and UNION filesystems are known to be
700 # buggy, and WILL panic your system if you attempt to do anything with
701 # them. They are included here as an incentive for some enterprising
702 # soul to sit down and fix them.
705 # One of these is mandatory:
706 options FFS #Fast filesystem
707 options MFS #Memory filesystem
708 options NFS #Network filesystem
710 # The rest are optional:
711 #options NFS_NOSERVER #Disable the NFS-server code.
712 options CD9660 #ISO 9660 filesystem
713 options FDESC #File descriptor filesystem
714 options HAMMER #HAMMER filesystem
715 options HPFS #OS/2 File system
716 options MSDOSFS #MS DOS filesystem
717 options NTFS #NT filesystem
718 options NULLFS #NULL filesystem
719 options NWFS #NetWare filesystem
720 options PORTAL #Portal filesystem
721 options PROCFS #Process filesystem
722 options PUFFS #Userspace file systems (e.g. ntfs-3g & sshfs)
723 options SMBFS #SMB/CIFS filesystem
724 options TMPFS #Temporary filesystem
725 options UDF #UDF filesystem
727 # YYY-DR Till we rework the VOP methods for this filesystem
728 #options UNION #Union filesystem
729 # The xFS_ROOT options REQUIRE the associated ``options xFS''
730 options FFS_ROOT #FFS usable as root device
731 options NFS_ROOT #NFS usable as root device
733 # Soft updates is technique for improving UFS filesystem speed and
734 # making abrupt shutdown less risky.
737 # Directory hashing improves the speed of operations on very large
738 # directories at the expense of some memory.
741 # Make space in the kernel for a root filesystem on a md device.
742 # Define to the number of kilobytes to reserve for the filesystem.
743 options MD_ROOT_SIZE=10
745 # Make the md device a potential root device, either with preloaded
746 # images of type mfs_root or md_root.
749 # Specify double the default maximum size for malloc(9)-backed md devices.
750 options MD_NSECT=40000
752 # Allow this many swap-devices.
754 # In order to manage swap, the system must reserve bitmap space that
755 # scales with the largest mounted swap device multiplied by NSWAPDEV,
756 # regardless of whether other swap devices exist or not. So it
757 # is not a good idea to make this value too large.
760 # Disk quotas are supported when this option is enabled.
761 options QUOTA #enable disk quotas
763 # If you are running a machine just as a fileserver for PC and MAC
764 # users, e.g. using SAMBA, you may consider setting this option
765 # and keeping all those users' directories on a filesystem that is
766 # mounted with the suiddir option. This gives new files the same
767 # ownership as the directory (similar to group). It's a security hole
768 # if you let these users run programs, so confine it to file-servers
769 # (but it'll save you lots of headaches in those cases). Root owned
770 # directories are exempt and X bits are cleared. The suid bit must be
771 # set on the directory as well; see chmod(1) PC owners can't see/set
772 # ownerships so they keep getting their toes trodden on. This saves
773 # you all the support calls as the filesystem it's used on will act as
774 # they expect: "It's my dir so it must be my file".
779 options NFS_MINATTRTIMO=3 # VREG attrib cache timeout in sec
780 options NFS_MAXATTRTIMO=60
781 options NFS_MINDIRATTRTIMO=30 # VDIR attrib cache timeout in sec
782 options NFS_MAXDIRATTRTIMO=60
783 options NFS_GATHERDELAY=10 # Default write gather delay (msec)
784 options NFS_UIDHASHSIZ=29 # Tune the size of nfssvc_sock with this
785 options NFS_WDELAYHASHSIZ=16 # and with this
786 options NFS_MUIDHASHSIZ=63 # Tune the size of nfsmount with this
787 options NFS_DEBUG # Enable NFS Debugging
790 options MSDOSFS_DEBUG # Enable MSDOSFS Debugging
793 # Add support for the EXT2FS filesystem of Linux fame. Be a bit
794 # careful with this - the ext2fs code has a tendency to lag behind
795 # changes and not be exercised very much, so mounting read/write could
796 # be dangerous (and even mounting read only could result in panics.)
800 # Optional character code conversion support with LIBICONV.
801 # Each option requires their base file system and LIBICONV.
803 options MSDOSFS_ICONV
806 #####################################################################
809 # Real time extensions added in the 1993 Posix
810 # P1003_1B: Infrastructure
811 # _KPOSIX_PRIORITY_SCHEDULING: Build in _POSIX_PRIORITY_SCHEDULING
812 # _KPOSIX_VERSION: Version kernel is built for
815 options _KPOSIX_PRIORITY_SCHEDULING
816 options _KPOSIX_VERSION=199309L
818 #####################################################################
821 # The granularity of operation is controlled by the kernel option HZ whose
822 # default value (100) means a granularity of 10ms (1s/HZ).
823 # Consider, however, that reducing the granularity too much might
824 # cause excessive overhead in clock interrupt processing,
825 # potentially causing ticks to be missed and thus actually reducing
826 # the accuracy of operation.
830 # The following options are used for debugging clock behavior only, and
831 # should not be used for production systems.
833 # CLK_CALIBRATION_LOOP will run the clock calibration loop at startup
834 # until the user presses a key.
836 options CLK_CALIBRATION_LOOP
838 # The following two options measure the frequency of the corresponding
839 # clock relative to the RTC (onboard mc146818a).
841 options CLK_USE_I8254_CALIBRATION
842 options CLK_USE_TSC_CALIBRATION
844 #####################################################################
847 # SCSI DEVICE CONFIGURATION
849 # The SCSI subsystem consists of the `base' SCSI code, a number of
850 # high-level SCSI device `type' drivers, and the low-level host-adapter
851 # device drivers. The host adapters are listed in the ISA and PCI
852 # device configuration sections below.
854 # Beginning with FreeBSD 2.0.5 you can wire down your SCSI devices so
855 # that a given bus, target, and LUN always come on line as the same
856 # device unit. In earlier versions the unit numbers were assigned
857 # in the order that the devices were probed on the SCSI bus. This
858 # means that if you removed a disk drive, you may have had to rewrite
859 # your /etc/fstab file, and also that you had to be careful when adding
860 # a new disk as it may have been probed earlier and moved your device
861 # configuration around.
863 # This old behavior is maintained as the default behavior. The unit
864 # assignment begins with the first non-wired down unit for a device
865 # type. For example, if you wire a disk as "da3" then the first
866 # non-wired disk will be assigned da4.
868 # The syntax for wiring down devices is:
870 # device scbus0 at ahc0 # Single bus device
871 # device scbus1 at ahc1 bus 0 # Single bus device
872 # device scbus3 at ahc2 bus 0 # Twin bus device
873 # device scbus2 at ahc2 bus 1 # Twin bus device
874 # device da0 at scbus0 target 0 unit 0
875 # device da1 at scbus3 target 1
876 # device da2 at scbus2 target 3
877 # device sa1 at scbus1 target 6
880 # "units" (SCSI logical unit number) that are not specified are
881 # treated as if specified as LUN 0.
883 # All SCSI devices allocate as many units as are required.
885 # The "unknown" device (uk? in pre-2.0.5) is now part of the base SCSI
886 # configuration and doesn't have to be explicitly configured.
888 device scbus #base SCSI code
889 device ch #SCSI media changers
890 device da #SCSI direct access devices (aka disks)
891 device sa #SCSI tapes
892 device cd #SCSI CD-ROMs
893 device pass #CAM passthrough driver
894 device sg #Passthrough device (linux scsi generic)
895 device pt #SCSI processor type
896 device ses #SCSI SES/SAF-TE driver
898 # Options for device mapper
900 device dm_target_crypt
901 device dm_target_linear
902 device dm_target_striped
905 device iscsi_initiator
906 options ISCSI_INITIATOR_DEBUG=8
910 # -- NOTE -- If you specify one of the bus/target/lun options, you must
912 # CAMDEBUG: When defined enables debugging macros
913 # CAM_DEBUG_BUS: Debug the given bus. Use -1 to debug all busses.
914 # CAM_DEBUG_TARGET: Debug the given target. Use -1 to debug all targets.
915 # CAM_DEBUG_LUN: Debug the given lun. Use -1 to debug all luns.
916 # CAM_DEBUG_FLAGS: OR together CAM_DEBUG_INFO, CAM_DEBUG_TRACE,
917 # CAM_DEBUG_SUBTRACE, and CAM_DEBUG_CDB
919 # CAM_MAX_HIGHPOWER: Maximum number of concurrent high power (start unit) cmds
920 # SCSI_NO_SENSE_STRINGS: When defined disables sense descriptions
921 # SCSI_NO_OP_STRINGS: When defined disables opcode descriptions
922 # SCSI_DELAY: The number of MILLISECONDS to freeze the SIM (scsi adapter)
923 # queue after a bus reset, and the number of milliseconds to
924 # freeze the device queue after a bus device reset. This
925 # can be changed at boot and runtime with the
926 # kern.cam.scsi_delay tunable/sysctl.
928 options CAM_DEBUG_BUS=-1
929 options CAM_DEBUG_TARGET=-1
930 options CAM_DEBUG_LUN=-1
931 options CAM_DEBUG_FLAGS="CAM_DEBUG_INFO|CAM_DEBUG_TRACE|CAM_DEBUG_CDB"
932 options CAM_MAX_HIGHPOWER=4
933 options SCSI_NO_SENSE_STRINGS
934 options SCSI_NO_OP_STRINGS
935 options SCSI_DELAY=8000 # Be pessimistic about Joe SCSI device
937 # Options for the CAM CDROM driver:
938 # CHANGER_MIN_BUSY_SECONDS: Guaranteed minimum time quantum for a changer LUN
939 # CHANGER_MAX_BUSY_SECONDS: Maximum time quantum per changer LUN, only
940 # enforced if there is I/O waiting for another LUN
941 # The compiled in defaults for these variables are 2 and 10 seconds,
944 # These can also be changed on the fly with the following sysctl variables:
945 # kern.cam.cd.changer.min_busy_seconds
946 # kern.cam.cd.changer.max_busy_seconds
948 options CHANGER_MIN_BUSY_SECONDS=2
949 options CHANGER_MAX_BUSY_SECONDS=10
951 # Options for the CAM sequential access driver:
952 # SA_IO_TIMEOUT: Timeout for read/write/wfm operations, in minutes
953 # SA_SPACE_TIMEOUT: Timeout for space operations, in minutes
954 # SA_REWIND_TIMEOUT: Timeout for rewind operations, in minutes
955 # SA_ERASE_TIMEOUT: Timeout for erase operations, in minutes
956 # SA_1FM_AT_EOD: Default to model which only has a default one filemark at EOT.
957 options SA_IO_TIMEOUT="(4)"
958 options SA_SPACE_TIMEOUT="(60)"
959 options SA_REWIND_TIMEOUT="(2*60)"
960 options SA_ERASE_TIMEOUT="(4*60)"
961 options SA_1FM_AT_EOD
963 # Optional timeout for the CAM processor target (pt) device
964 # This is specified in seconds. The default is 60 seconds.
965 options SCSI_PT_DEFAULT_TIMEOUT="60"
967 # Optional enable of doing SES passthrough on other devices (e.g., disks)
969 # Normally disabled because a lot of newer SCSI disks report themselves
970 # as having SES capabilities, but this can then clot up attempts to build
971 # build a topology with the SES device that's on the box these drives
973 options SES_ENABLE_PASSTHROUGH
975 #####################################################################
976 # MISCELLANEOUS DEVICES AND OPTIONS
978 # The `pty' device usually turns out to be ``effectively mandatory'',
979 # as it is required for `telnetd', `rlogind', `screen', `emacs', and
980 # `xterm', among others.
982 pseudo-device pty #Pseudo ttys
983 pseudo-device gzip #Exec gzipped a.out's
984 pseudo-device vn #Vnode driver (turns a file into a device)
985 pseudo-device md #Memory/malloc disk
986 pseudo-device putter #for puffs and pud
987 pseudo-device snp #Snoop device - to look at pty/vty/etc..
988 pseudo-device ccd 4 #Concatenated disk driver
990 # Configuring Vinum into the kernel is not necessary, since the kld
991 # module gets started automatically when vinum(8) starts. This
992 # device is also untested. Use at your own risk.
994 # The option VINUMDEBUG must match the value set in CFLAGS
995 # in src/sbin/vinum/Makefile. Failure to do so will result in
996 # the following message from vinum(8):
998 # Can't get vinum config: Invalid argument
1000 # see vinum(4) for more reasons not to use these options.
1001 pseudo-device vinum #Vinum concat/mirror/raid driver
1002 options VINUMDEBUG #enable Vinum debugging hooks
1004 # Kernel side iconv library
1007 # Size of the kernel message buffer. Should be N * pagesize.
1008 options MSGBUF_SIZE=40960
1010 #####################################################################
1011 # HARDWARE DEVICE CONFIGURATION
1016 # Mandatory ISA devices: isa, npx
1020 # ISA-PnP BIOS support
1024 # Options for `isa':
1026 # AUTO_EOI_1 enables the `automatic EOI' feature for the master 8259A
1027 # interrupt controller. This saves about 0.7-1.25 usec for each interrupt.
1028 # This option breaks suspend/resume on some portables.
1030 # AUTO_EOI_2 enables the `automatic EOI' feature for the slave 8259A
1031 # interrupt controller. This saves about 0.7-1.25 usec for each interrupt.
1032 # Automatic EOI is documented not to work for for the slave with the
1033 # original i8259A, but it works for some clones and some integrated
1036 # MAXMEM specifies the amount of RAM on the machine; if this is not
1037 # specified, DragonFly will first read the amount of memory from the CMOS
1038 # RAM, so the amount of memory will initially be limited to 64MB or 16MB
1039 # depending on the BIOS. If the BIOS reports 64MB, a memory probe will
1040 # then attempt to detect the installed amount of RAM. If this probe
1041 # fails to detect >64MB RAM you will have to use the MAXMEM option.
1042 # The amount is in kilobytes, so for a machine with 128MB of RAM, it would
1043 # be 131072 (128 * 1024).
1045 # BROKEN_KEYBOARD_RESET disables the use of the keyboard controller to
1046 # reset the CPU for reboot. This is needed on some systems with broken
1047 # keyboard controllers.
1049 options COMPAT_OLDISA #FreeBSD 2.2 and 3.x compatibility shims
1052 options MAXMEM="(128*1024)"
1053 #options BROKEN_KEYBOARD_RESET
1055 # Enable support for the kernel PLL to use an external PPS signal,
1056 # under supervision of [x]ntpd(8)
1057 # More info in ntpd documentation: http://www.eecis.udel.edu/~ntp
1061 # The keyboard controller; it controls the keyboard and the PS/2 mouse.
1062 device atkbdc0 at isa? port IO_KBD
1065 device atkbd0 at atkbdc? irq 1
1067 # Options for atkbd:
1068 options ATKBD_DFLT_KEYMAP # specify the built-in keymap
1069 makeoptions ATKBD_DFLT_KEYMAP="jp.106"
1071 # These options are valid for other keyboard drivers as well.
1072 options KBD_DISABLE_KEYMAP_LOAD # refuse to load a keymap
1073 options KBD_INSTALL_CDEV # install a CDEV entry in /dev
1075 # `flags' for atkbd:
1076 # 0x01 Force detection of keyboard, else we always assume a keyboard
1077 # 0x02 Don't reset keyboard, useful for some newer ThinkPads
1078 # 0x03 Force detection and avoid reset, might help with certain
1080 # 0x04 Old-style (XT) keyboard support, useful for older ThinkPads
1083 device psm0 at atkbdc? irq 12
1086 options PSM_HOOKRESUME #hook the system resume event, useful
1088 options PSM_RESETAFTERSUSPEND #reset the device at the resume event
1090 device kbdmux # keyboard multiplexer
1092 # The video card driver.
1096 # Try the following option if the mouse pointer is not drawn correctly
1097 # or font does not seem to be loaded properly. May cause flicker on
1099 options VGA_ALT_SEQACCESS
1101 options VGA_DEBUG=2 # enable VGA debug output
1103 # If you experience problems switching back to 80x25 (or a derived mode),
1104 # the following option might help.
1105 #options VGA_KEEP_POWERON_MODE # use power-on settings for 80x25
1107 # If you can dispense with some vga driver features, you may want to
1108 # use the following options to save some memory.
1109 #options VGA_NO_FONT_LOADING # don't save/load font
1110 #options VGA_NO_MODE_CHANGE # don't change video modes
1112 # The following option probably won't work with the LCD displays.
1113 options VGA_WIDTH90 # support 90 column modes
1115 # To include support for VESA video modes
1117 options VESA_DEBUG=2 # enable VESA debug output
1119 # Splash screen at start up! Screen savers require this too.
1120 pseudo-device splash
1122 # The syscons console driver (sco color console compatible).
1124 options MAXCONS=16 # number of virtual consoles
1125 options SC_ALT_MOUSE_IMAGE # simplified mouse cursor in text mode
1126 options SC_DEBUG_LEVEL=5 # enable debug output
1127 options SC_DFLT_FONT # compile font in
1128 makeoptions SC_DFLT_FONT=cp850
1129 options SC_DISABLE_DDBKEY # disable `debug' key
1130 options SC_DISABLE_REBOOT # disable reboot key sequence
1131 options SC_HISTORY_SIZE=200 # number of history buffer lines
1132 options SC_MOUSE_CHAR=0x3 # char code for text mode mouse cursor
1133 options SC_PIXEL_MODE # add support for the raster text mode
1135 # The following options will let you change the default colors of syscons.
1136 options SC_NORM_ATTR="(FG_GREEN|BG_BLACK)"
1137 options SC_NORM_REV_ATTR="(FG_YELLOW|BG_GREEN)"
1138 options SC_KERNEL_CONS_ATTR="(FG_RED|BG_BLACK)"
1139 options SC_KERNEL_CONS_REV_ATTR="(FG_BLACK|BG_RED)"
1141 # If you have a two button mouse, you may want to add the following option
1142 # to use the right button of the mouse to paste text.
1143 options SC_TWOBUTTON_MOUSE
1145 # You can selectively disable features in syscons.
1146 #options SC_NO_CUTPASTE
1147 #options SC_NO_FONT_LOADING
1148 #options SC_NO_HISTORY
1149 #options SC_NO_SYSMOUSE
1152 # The Numeric Processing eXtension driver. In addition to this, you
1153 # may configure a math emulator (see above). If your machine has a
1154 # hardware FPU and the kernel configuration includes the npx device
1155 # *and* a math emulator compiled into the kernel, the hardware FPU
1156 # will be used, unless it is found to be broken or unless "flags" to
1157 # npx0 includes "0x08", which requests preference for the emulator.
1158 device npx0 at nexus? port IO_NPX flags 0x0 irq 13
1162 # 0x01 don't use the npx registers to optimize bcopy.
1163 # 0x02 don't use the npx registers to optimize bzero.
1164 # 0x04 don't use the npx registers to optimize copyin or copyout.
1165 # 0x08 use emulator even if hardware FPU is available.
1166 # The npx registers are normally used to optimize copying and zeroing when
1167 # all of the following conditions are satisfied:
1168 # I586_CPU is an option
1169 # the cpu is an i586 (perhaps not a Pentium)
1170 # the probe for npx0 succeeds
1171 # INT 16 exception handling works.
1172 # Then copying and zeroing using the npx registers is normally 30-100% faster.
1173 # The flags can be used to control cases where it doesn't work or is slower.
1174 # Setting them at boot time using userconfig works right (the optimizations
1175 # are not used until later in the bootstrap when npx0 is attached).
1176 # Flag 0x08 automatically disables the i586 optimized routines.
1180 # SCSI host adapters: `bt'
1182 # adv: All Narrow SCSI bus AdvanSys controllers.
1183 # adw: Second Generation AdvanSys controllers including the ADV940UW.
1184 # ahc: Adaptec 274x/284x/294x
1186 # bt: Most Buslogic controllers
1187 # ncv: NCR 53C500 based SCSI host adapters.
1188 # nsp: Workbit Ninja SCSI-3 based PC Card SCSI host adapters.
1189 # stg: TMC 18C30, 18C50 based ISA/PC Card SCSI host adapters.
1191 # Note that the order is important in order for Buslogic cards to be
1195 device bt0 at isa? port IO_BT0
1201 device stg0 at isa? port 0x140 irq 11
1204 # Adaptec FSA RAID controllers, including integrated DELL controller,
1205 # the Dell PERC 2/QC and the HP NetRAID-4M
1209 device aacp # SCSI Passthrough interface (optional, CAM required)
1212 # Compaq Smart RAID, Mylex DAC960 and AMI MegaRAID controllers. Only
1213 # one entry is needed; the code will find and configure all supported
1216 device ida # Compaq Smart RAID
1217 device mlx # Mylex DAC960
1218 device amr # AMI MegaRAID
1219 device amrp # SCSI Passthrough interface (optional, CAM req.)
1220 device mfi # LSI MegaRAID SAS
1221 device mfip # LSI MegaRAID SAS passthrough, requires CAM
1225 # Areca RAID (CAM is required).
1227 device arcmsr # Areca SATA II RAID
1230 # Highpoint RocketRAID 182x.
1234 # Highpoint RocketRaid 3xxx series SATA RAID
1240 device twe # 3ware ATA RAID
1241 device twa # 3ware 9000 series PATA/SATA RAID
1242 options TWA_DEBUG=10 # enable debug messages
1243 device tws # 3ware 9750 series SATA/SAS RAID
1246 # Promise Supertrack SX6000
1255 # AHCI driver, this will override NATA for AHCI devices,
1256 # both drivers may be included.
1260 # SiI3124/3132 driver
1264 # The 'NATA' driver supports all ATA and ATAPI devices.
1265 # You only need one "device nata" for it to find all
1266 # PCI ATA/ATAPI devices on modern machines.
1269 device natadisk # ATA disk drives
1270 device natapicd # ATAPI CD/DVD drives
1271 device natapifd # ATAPI floppy drives
1272 device natapist # ATAPI tape drives
1273 device natapicam # ATAPI CAM layer emulation
1274 device nataraid # support for ATA software RAID controllers
1275 device natausb # ATA-over-USB support
1277 # The following options are valid for the NATA driver:
1279 # ATA_STATIC_ID: controller numbering is static (like the old driver)
1280 # else the device numbers are dynamically allocated.
1281 options ATA_STATIC_ID
1283 # For older non-PCI systems, these are the lines to use:
1285 #device nata0 at isa? port IO_WD1 irq 14
1286 #device nata1 at isa? port IO_WD2 irq 15
1289 # Standard floppy disk controllers: `fdc' and `fd'
1291 device fdc0 at isa? port IO_FD1 irq 6 drq 2
1293 # FDC_DEBUG enables floppy debugging. Since the debug output is huge, you
1294 # gotta turn it actually on by setting the variable fd_debug with DDB,
1298 device fd0 at fdc0 drive 0
1299 device fd1 at fdc0 drive 1
1302 # sio: serial ports (see sio(4))
1304 device sio0 at isa? port IO_COM1 flags 0x10 irq 4
1307 # `flags' for serial drivers that support consoles (only for sio now):
1308 # 0x10 enable console support for this unit. The other console flags
1309 # are ignored unless this is set. Enabling console support does
1310 # not make the unit the preferred console - boot with -h or set
1311 # the 0x20 flag for that. Currently, at most one unit can have
1312 # console support; the first one (in config file order) with
1313 # this flag set is preferred. Setting this flag for sio0 gives
1314 # the old behaviour.
1315 # 0x20 force this unit to be the console (unless there is another
1316 # higher priority console). This replaces the COMCONSOLE option.
1317 # 0x40 reserve this unit for low level console operations. Do not
1318 # access the device in any normal way.
1319 # 0x80 use this port for serial line gdb support in ddb.
1321 # PnP `flags' (set via userconfig using pnp x flags y)
1322 # 0x1 disable probing of this device. Used to prevent your modem
1323 # from being attached as a PnP modem.
1326 # Options for serial drivers that support consoles (only for sio now):
1327 options BREAK_TO_DEBUGGER #a BREAK on a comconsole goes to
1329 options CONSPEED=115200 # speed for serial console
1332 # Solaris implements a new BREAK which is initiated by a character
1333 # sequence CR ~ ^b which is similar to a familiar pattern used on
1334 # Sun servers by the Remote Console.
1335 options ALT_BREAK_TO_DEBUGGER
1338 options COM_ESP #code for Hayes ESP
1339 options COM_MULTIPORT #code for some cards with shared IRQs
1341 # Other flags for sio that aren't documented in the man page.
1342 # 0x20000 enable hardware RTS/CTS and larger FIFOs. Only works for
1343 # ST16650A-compatible UARTs.
1345 # PCI Universal Communications driver
1346 # Supports various single and multi port PCI serial cards. Maybe later
1347 # also the parallel ports on combination serial/parallel cards. New cards
1348 # can be added in src/sys/dev/misc/puc/pucdata.c.
1352 # Network interfaces: `ed', `ep', `is', `lnc'
1354 # ar: Arnet SYNC/570i hdlc sync 2/4 port V.35/X.21 serial driver (requires sppp)
1355 # cs: IBM Etherjet and other Crystal Semi CS89x0-based adapters
1356 # ed: Western Digital and SMC 80xx; Novell NE1000 and NE2000; 3Com 3C503
1358 # ex: Intel EtherExpress Pro/10 and other i82595-based adapters
1359 # fe: Fujitsu MB86960A/MB86965A Ethernet
1360 # lnc: Lance/PCnet cards (Isolan, Novell NE2100, NE32-VL, AMD Am7990 & Am79C960)
1361 # sbni: Granch SBNI12-xx adapters
1362 # sbsh: Granch SBNI16 SHDSL modem PCI adapters
1363 # sr: RISCom/N2 hdlc sync 1/2 port V.35/X.21 serial driver (requires sppp)
1364 # wi: Lucent WaveLAN/IEEE 802.11 PCMCIA adapters. Note: this supports both
1365 # the PCMCIA and ISA cards: the ISA card is really a PCMCIA to ISA
1366 # bridge with a PCMCIA adapter plugged into it.
1367 # an: Aironet 4500/4800 802.11 wireless adapters. Supports the PCMCIA,
1368 # PCI and ISA varieties.
1369 # xe: Xircom/Intel EtherExpress Pro100/16 PC Card ethernet controller.
1371 device ar0 at isa? port 0x300 irq 10 iomem 0xd0000
1372 device cs0 at isa? port 0x300
1373 device ed0 at isa? port 0x280 irq 5 iomem 0xd8000
1376 device fe0 at isa? port 0x300
1377 device lnc0 at isa? port 0x280 irq 10 drq 0
1378 device sbni0 at isa? port 0x210 irq 5 flags 0xefdead
1381 device sn0 at isa? port 0x300 irq 10
1383 # Wlan support is mandatory for some wireless LAN devices.
1384 options IEEE80211_DEBUG #enable debugging msgs
1385 options IEEE80211_AMPDU_AGE #age frames in AMPDU reorder q's
1386 options IEEE80211_SUPPORT_MESH #enable 802.11s D3.0 support
1387 options IEEE80211_SUPPORT_TDMA #enable TDMA support
1388 device wlan # 802.11 support
1389 device wlan_acl # 802.11 MAC-based access control for AP
1390 device wlan_ccmp # 802.11 CCMP support
1391 device wlan_tkip # 802.11 TKIP support
1392 device wlan_wep # 802.11 WEP support
1393 device wlan_xauth # 802.11 WPA or 802.1x authentication for AP
1394 device wlan_amrr # 802.11 AMRR TX rate control algorithm
1395 device an # Aironet Communications 4500/4800
1396 device ath # Atheros AR521x
1397 options AH_SUPPORT_AR5416
1398 device ath_hal # Atheros Hardware Access Layer
1399 #device ath_rate_amrr # Atheros AMRR TX rate control algorithm
1400 #device ath_rate_onoe # Atheros Onoe TX rate control algorithm
1401 device ath_rate_sample # Atheros Sample TX rate control algorithm
1402 options ATH_DEBUG # turn on debugging output (see hw.ath.debug)
1403 options ATH_DIAGAPI # diagnostic interface to the HAL
1404 options ATH_RXBUF=80 # number of RX buffers to allocate
1405 options ATH_TXBUF=400 # number of TX buffers to allocate
1406 #device iwl # Intel PRO/Wireless 2100
1407 device iwi # Intel PRO/Wireless 2200BG/2915ABG
1408 device iwn # Intel WiFi Link 4965/1000/5000/5150/5300/6000/6050
1409 device wi # WaveLAN/IEEE, PRISM-II, Spectrum24 802.11DS
1410 #device rtw # RealTek 8180
1411 #device acx # TI ACX100/ACX111.
1412 device xe # Xircom PCMCIA
1413 device ral # Ralink Technology 802.11 wireless NIC
1416 # IEEE 802.11 adapter firmware modules
1418 # iwifw: Intel PRO/Wireless 2200BG/2225BG/2915ABG firmware
1419 # iwnfw: Intel WiFi Link 4965/1000/5000/5150/5300/6000/6050
1420 # ralfw: Ralink Technology RT25xx and RT26xx firmware
1421 # wpifw: Intel 3945ABG Wireless LAN Controller firmware
1428 # Bluetooth Protocols
1432 # ATM related options
1434 # The `en' device provides support for Efficient Networks (ENI)
1435 # ENI-155 PCI midway cards, and the Adaptec 155Mbps PCI ATM cards (ANA-59x0).
1437 # atm pseudo-device provides generic atm functions and is required for
1439 # NATM enables the netnatm protocol family that can be used to
1442 # the current driver supports only PVC operations (no atm-arp, no multicast).
1443 # for more details, please read the original documents at
1444 # http://www.ccrc.wustl.edu/pub/chuck/tech/bsdatm/bsdatm.html
1448 options NATM #native ATM
1452 # The flags of the device tells the device a bit more info about the
1453 # device that normally is obtained through the PnP interface.
1454 # bit 2..0 secondary DMA channel;
1455 # bit 4 set if the board uses two dma channels;
1456 # bit 15..8 board type, overrides autodetection; leave it
1457 # zero if don't know what to put in (and you don't,
1458 # since this is unsupported at the moment...).
1460 # This driver will use the new PnP code if it's available. You might
1461 # need PNPBIOS for ISA devices.
1463 # If you have a GUS-MAX card and want to use the CS4231 codec on the
1464 # card the drqs for the gus max must be 8 bit (1, 2, or 3).
1466 # If you would like to use the full duplex option on the gus, then define
1467 # flags to be the ``read dma channel''.
1470 # Basic sound card support:
1472 # For PnP/PCI sound cards:
1474 device "snd_als4000"
1480 device "snd_emu10k1"
1487 device "snd_maestro"
1488 device "snd_maestro3"
1490 device "snd_neomagic"
1495 device "snd_t4dwave"
1496 device "snd_via8233"
1497 device "snd_via82c686"
1499 # For non-pnp sound cards:
1500 device pcm0 at isa? irq 10 drq 1 flags 0x0
1505 # Miscellaneous hardware:
1507 # apm: Laptop Advanced Power Management (experimental)
1508 # bktr: Brooktree bt848/848a/849a/878/879 video capture and TV Tuner board
1509 # cy: Cyclades serial driver
1510 # ecc: ECC memory controller
1512 # nrp: Comtrol Rocketport(ISA) - single card
1513 # si: Specialix SI/XIO 4-32 port terminal multiplexor
1514 # spic: Sony Programmable I/O controller (VAIO notebooks)
1515 # stl: Stallion EasyIO and EasyConnection 8/32 (ISA and PCI), EasyConnection 8/64 PCI
1516 # stli: Stallion EasyConnection 8/64 ISA, ONboard, Brumby (intelligent)
1517 # nmdm: nullmodem terminal driver (see nmdm(4))
1520 # The flags takes the following meaning for apm0:
1521 # 0x0020 Statclock is broken.
1522 # If apm is omitted, some systems require sysctl -w kern.timecounter.method=1
1523 # for correct timekeeping.
1525 # Notes on the Comtrol Rocketport driver:
1527 # The exact values used for nrp0 depend on how many boards you have
1528 # in the system. The manufacturer's sample configs are listed as:
1530 # Comtrol Rocketport ISA single card
1531 # device nrp0 at isa? port 0x280
1533 # If instead you have two ISA cards, one installed at 0x100 and the
1534 # second installed at 0x180, then you should add the following to
1535 # your kernel configuration file:
1537 # device nrp0 at isa? port 0x100
1538 # device nrp1 at isa? port 0x180
1540 # For 4 ISA cards, it might be something like this:
1542 # device nrp0 at isa? port 0x180
1543 # device nrp1 at isa? port 0x100
1544 # device nrp2 at isa? port 0x340
1545 # device nrp3 at isa? port 0x240
1547 # And for PCI cards, you only need say:
1551 # Notes on the Specialix SI/XIO driver:
1552 # **This is NOT a Specialix supported Driver!**
1553 # The host card is memory, not IO mapped.
1554 # The Rev 1 host cards use a 64K chunk, on a 32K boundary.
1555 # The Rev 2 host cards use a 32K chunk, on a 32K boundary.
1556 # The cards can use an IRQ of 11, 12 or 15.
1558 # Notes on the Stallion stl and stli drivers:
1559 # See src/sys/platform/pc32/isa/README.stl for complete instructions.
1560 # This is version 2.0.0, unsupported by Stallion.
1561 # The stl driver has a secondary IO port hard coded at 0x280. You need
1562 # to change src/sys/dev/serial/stl/stallion.c if you reconfigure this on the boards.
1563 # The "flags" and "iosiz" settings on the stli driver depend on the board:
1564 # EasyConnection 8/64 ISA: flags 23 iosiz 0x1000
1565 # ONboard ISA: flags 4 iosiz 0x10000
1566 # Brumby: flags 2 iosiz 0x4000
1567 # Stallion: flags 1 iosiz 0x10000
1568 # For the PCI cards, "device stl" will suffice.
1572 device joy0 at isa? port IO_GAME
1573 device cy0 at isa? irq 10 iomem 0xd4000 iosiz 0x2000
1575 device si0 at isa? iomem 0xd0000 irq 12
1576 device spic0 at isa? irq 0 port 0x10a0
1577 device stl0 at isa? port 0x2a0 irq 10
1578 device stli0 at isa? port 0x2a0 iomem 0xcc000 flags 23 iosiz 0x1000
1579 # nullmodem terminal driver
1582 # The `ahc' device provides support for the Adaptec 274X and 284X
1586 # The aic7xxx driver will attempt to use memory mapped I/O for all PCI
1587 # controllers that have it configured only if this option is set. Unfortunately,
1588 # this doesn't work on some motherboards, which prevents it from being the
1590 options AHC_ALLOW_MEMIO
1592 # The adw driver will attempt to use memory mapped I/O for all PCI
1593 # controllers that have it configured only if this option is set.
1594 options ADW_ALLOW_MEMIO
1597 # PCI devices & PCI options:
1599 # The main PCI bus device is `pci'. It provides auto-detection and
1600 # configuration support for all devices on the PCI bus, using either
1601 # configuration mode defined in the PCI specification.
1607 options COMPAT_OLDPCI #FreeBSD 2.2 and 3.x compatibility shims
1614 # The `ahc' device provides support for the Adaptec 29/3940(U)(W)
1615 # and motherboard based AIC7870/AIC7880 adapters.
1617 options AHC_DEBUG_OPTS=0xffffffff
1618 options AHC_REG_PRETTY_PRINT
1619 options AHC_TMODE_ENABLE
1621 # The 'ahd' device provides support for the Adaptec 79xx Ultra320
1622 # SCSI adapters. Options are documented in the ahd(4) manpage:
1624 options AHD_DEBUG_OPTS=0xffffffff
1625 options AHD_REG_PRETTY_PRINT
1626 #options AHD_TMODE_ENABLE=0xff
1628 # The `amd' device provides support for the AMD 53C974 SCSI host
1629 # adapter chip as found on devices such as the Tekram DC-390(T).
1631 # The `bge' device provides support for gigabit ethernet adapters
1632 # based on the Broadcom BCM570x family of controllers, including the
1633 # 3Com 3c996-T, the Netgear GA302T, the SysKonnect SK-9D21 and SK-9D41,
1634 # and the embedded gigE NICs on Dell PowerEdge 2550 servers.
1636 # The `ncr' device provides support for the NCR 53C810 and 53C825
1637 # self-contained SCSI host adapters.
1639 # The `isp' device provides support for the Qlogic ISP 1020, 1040
1640 # nd 1040B PCI SCSI host adapters, ISP 1240 Dual Ultra SCSI,
1641 # ISP 1080 and 1280 (Dual) Ultra2, ISP 12160 Ultra3 SCSI, as well as
1642 # the Qlogic ISP 2100 and ISP 2200 Fibre Channel Host Adapters.
1644 # The `dc' device provides support for PCI fast ethernet adapters
1645 # based on the DEC/Intel 21143 and various workalikes including:
1646 # the ADMtek AL981 Comet and AN985 Centaur, the ASIX Electronics
1647 # AX88140A and AX88141, the Davicom DM9100 and DM9102, the Lite-On
1648 # 82c168 and 82c169 PNIC, the Lite-On/Macronix LC82C115 PNIC II
1649 # and the Macronix 98713/98713A/98715/98715A/98725 PMAC. This driver
1650 # replaces the old al, ax, dm, pn and mx drivers. List of brands:
1651 # Digital DE500-BA, Kingston KNE100TX, D-Link DFE-570TX, SOHOware SFA110,
1652 # SVEC PN102-TX, CNet Pro110B, 120A, and 120B, Compex RL100-TX,
1653 # LinkSys LNE100TX, LNE100TX V2.0, Jaton XpressNet, Alfa Inc GFC2204,
1656 # The `de' device provides support for the Digital Equipment DC21040
1657 # self-contained Ethernet adapter.
1659 # The `em' device provides support for the Intel Pro/1000 Family of Gigabit
1660 # adapters (82542, 82543, 82544, 82540).
1662 # The `et' device provides support for the Agere ET1310 10/100/1000 PCIe
1665 # The `fxp' device provides support for the Intel EtherExpress Pro/100B
1666 # PCI Fast Ethernet adapters.
1668 # The 'lge' device provides support for PCI gigabit ethernet adapters
1669 # based on the Level 1 LXT1001 NetCellerator chipset. This includes the
1670 # D-Link DGE-500SX, SMC TigerCard 1000 (SMC9462SX), and some Addtron cards.
1672 # The 'my' device provides support for the Myson MTD80X and MTD89X PCI
1673 # Fast Ethernet adapters.
1675 # The 'nge' device provides support for PCI gigabit ethernet adapters
1676 # based on the National Semiconductor DP83820 and DP83821 chipset. This
1677 # includes the SMC EZ Card 1000 (SMC9462TX), D-Link DGE-500T, Asante
1678 # FriendlyNet GigaNIX 1000TA and 1000TPC, the Addtron AEG320T, the
1679 # LinkSys EG1032 and EG1064, the Surecom EP-320G-TX and the Netgear GA622T.
1681 # The 'pcn' device provides support for PCI fast ethernet adapters based
1682 # on the AMD Am79c97x chipsets, including the PCnet/FAST, PCnet/FAST+,
1683 # PCnet/PRO and PCnet/Home. These were previously handled by the lnc
1684 # driver (and still will be if you leave this driver out of the kernel).
1686 # Te 're' device provides support for PCI GigaBit ethernet adapters based
1687 # on the RealTek 8169 chipset. It also supports the 8139C+ and is the
1688 # preferred driver for that chip.
1690 # The 'rl' device provides support for PCI fast ethernet adapters based
1691 # on the RealTek 8129/8139 chipset. Note that the RealTek driver defaults
1692 # to using programmed I/O to do register accesses because memory mapped
1693 # mode seems to cause severe lockups on SMP hardware. This driver also
1694 # supports the Accton EN1207D `Cheetah' adapter, which uses a chip called
1695 # the MPX 5030/5038, which is either a RealTek in disguise or a RealTek
1696 # workalike. Note that the D-Link DFE-530TX+ uses the RealTek chipset
1697 # and is supported by this driver, not the 'vr' driver.
1699 # The 'sf' device provides support for Adaptec Duralink PCI fast
1700 # ethernet adapters based on the Adaptec AIC-6915 "starfire" controller.
1701 # This includes dual and quad port cards, as well as one 100baseFX card.
1702 # Most of these are 64-bit PCI devices, except for one single port
1703 # card which is 32-bit.
1705 # The 'ste' device provides support for adapters based on the Sundance
1706 # Technologies ST201 PCI fast ethernet controller. This includes the
1709 # The 'sis' device provides support for adapters based on the Silicon
1710 # Integrated Systems SiS 900 and SiS 7016 PCI fast ethernet controller
1713 # The 'sk' device provides support for the SysKonnect SK-984x series
1714 # PCI gigabit ethernet NICs. This includes the SK-9841 and SK-9842
1715 # single port cards (single mode and multimode fiber) and the
1716 # SK-9843 and SK-9844 dual port cards (also single mode and multimode).
1717 # The driver will autodetect the number of ports on the card and
1718 # attach each one as a separate network interface.
1720 # The 'ti' device provides support for PCI gigabit ethernet NICs based
1721 # on the Alteon Networks Tigon 1 and Tigon 2 chipsets. This includes the
1722 # Alteon AceNIC, the 3Com 3c985, the Netgear GA620 and various others.
1723 # Note that you will probably want to bump up NMBCLUSTERS a lot to use
1726 # The 'tl' device provides support for the Texas Instruments TNETE100
1727 # series 'ThunderLAN' cards and integrated ethernet controllers. This
1728 # includes several Compaq Netelligent 10/100 cards and the built-in
1729 # ethernet controllers in several Compaq Prosignia, Proliant and
1730 # Deskpro systems. It also supports several Olicom 10Mbps and 10/100
1733 # The `tx' device provides support for the SMC 9432 TX, BTX and FTX cards.
1735 # The `txp' device provides support for the 3Com 3cR990 "Typhoon"
1738 # The `vr' device provides support for various fast ethernet adapters
1739 # based on the VIA Technologies VT3043 `Rhine I' and VT86C100A `Rhine II'
1740 # chips, including the D-Link DFE530TX (see 'rl' for DFE530TX+), the Hawking
1741 # Technologies PN102TX, and the AOpen/Acer ALN-320.
1743 # The `vx' device provides support for the 3Com 3C590 and 3C595
1746 # The `wb' device provides support for various fast ethernet adapters
1747 # based on the Winbond W89C840F chip. Note: this is not the same as
1748 # the Winbond W89C940F, which is an NE2000 clone.
1750 # The `xl' device provides support for the 3Com 3c900, 3c905 and
1751 # 3c905B (Fast) Etherlink XL cards and integrated controllers. This
1752 # includes the integrated 3c905B-TX chips in certain Dell Optiplex and
1753 # Dell Precision desktop machines and the integrated 3c905-TX chips
1754 # in Dell Latitude laptop docking stations.
1756 # The 'bktr' device is a PCI video capture device using the Brooktree
1757 # bt848/bt848a/bt849a/bt878/bt879 chipset. When used with a TV Tuner it forms a
1758 # TV card, eg Miro PC/TV, Hauppauge WinCast/TV WinTV, VideoLogic Captivator,
1759 # Intel Smart Video III, AverMedia, IMS Turbo, FlyVideo.
1761 # options OVERRIDE_CARD=xxx
1762 # options OVERRIDE_TUNER=xxx
1763 # options OVERRIDE_MSP=1
1764 # options OVERRIDE_DBX=1
1765 # These options can be used to override the auto detection
1766 # The current values for xxx are found in src/sys/dev/video/bktr/bktr_card.h
1767 # Using sysctl(8) run-time overrides on a per-card basis can be made
1769 # options BKTR_SYSTEM_DEFAULT=BROOKTREE_PAL
1771 # options BKTR_SYSTEM_DEFAULT=BROOKTREE_NTSC
1772 # Specifes the default video capture mode.
1773 # This is required for Dual Crystal (28&35Mhz) boards where PAL is used
1774 # to prevent hangs during initialisation. eg VideoLogic Captivator PCI.
1776 # options BKTR_USE_PLL
1777 # PAL or SECAM users who have a 28Mhz crystal (and no 35Mhz crystal)
1778 # must enable PLL mode with this option. eg some new Bt878 cards.
1780 # options BKTR_GPIO_ACCESS
1781 # This enable IOCTLs which give user level access to the GPIO port.
1783 # options BKTR_NO_MSP_RESET
1784 # Prevents the MSP34xx reset. Good if you initialise the MSP in another OS first
1786 # options BKTR_430_FX_MODE
1787 # Switch Bt878/879 cards into Intel 430FX chipset compatibility mode.
1789 # options BKTR_SIS_VIA_MODE
1790 # Switch Bt878/879 cards into SIS/VIA chipset compatibility mode which is
1791 # needed for some old SiS and VIA chipset motherboards.
1792 # This also allows Bt878/879 chips to work on old OPTi (<1997) chipset
1793 # motherboards and motherboards with bad or incomplete PCI 2.1 support.
1794 # As a rough guess, old = before 1998
1796 # options BKTR_NEW_MSP34XX_DRIVER
1797 # Use new, more complete initialization scheme for the msp34* soundchip.
1798 # Should fix stereo autodetection if the old driver does only output
1801 # options BKTR_OVERRIDE_CARD=xxx
1802 # options BKTR_OVERRIDE_DBX=xxx
1803 # options BKTR_OVERRIDE_MSP=xxx
1804 # options BKTR_OVERRIDE_TUNER=xxx
1805 # These options can be used to select a specific device, regardless of
1806 # the autodetection and i2c device checks (see comments in bktr_card.c).
1808 device ahc # AHA2940 and onboard AIC7xxx devices
1809 device ahd # AIC79xx devices
1810 device amd # AMD 53C974 (Tekram DC-390(T))
1811 device isp # Qlogic family
1812 device ispfw # Firmware for QLogic HBAs
1813 device mpt # LSI '909 FC adapters
1814 device mps # LSI-Logic MPT-Fusion 2
1815 device ncr # NCR/Symbios Logic
1816 device sym # NCR/Symbios Logic (newer chipsets)
1817 device trm # Tekram DC395U/UW/F and DC315U
1821 # ISP_TARGET_MODE - enable target mode operation
1822 #options ISP_TARGET_MODE=1
1824 # Options used in dev/disk/sym/ (Symbios SCSI driver).
1825 #options SYM_SETUP_LP_PROBE_MAP #-Low Priority Probe Map (bits)
1826 # Allows the ncr to take precedence
1827 # 1 (1<<0) -> 810a, 860
1828 # 2 (1<<1) -> 825a, 875, 885, 895
1829 # 4 (1<<2) -> 895a, 896, 1510d
1830 #options SYM_SETUP_SCSI_DIFF #-HVD support for 825a, 875, 885
1831 # disabled:0 (default), enabled:1
1832 #options SYM_SETUP_PCI_PARITY #-PCI parity checking
1833 # disabled:0, enabled:1 (default)
1834 #options SYM_SETUP_MAX_LUN #-Number of LUNs supported
1835 # default:8, range:[1..64]
1838 # MII bus support is required for some PCI 10/100 ethernet NICs,
1839 # namely those which use MII-compliant transceivers or implement
1840 # transceiver control interfaces that operate like an MII. Adding
1841 # "device miibus0" to the kernel config pulls in support for
1842 # the generic miibus API and all of the PHY drivers, including a
1843 # generic one for PHYs that aren't specifically handled by an
1844 # individual driver.
1847 # PCI Ethernet NICs that use the common MII bus controller code.
1848 device ae # Attansic/Atheros L2 Fast Ethernet
1849 device alc # Atheros AR8131/AR8132
1850 device ale # Atheros AR8121/AR8113/AR8114
1851 device age # Attansic/Atheros L1 Gigabit Ethernet
1852 device bce # Broadcom NetXtreme II Gigabit Ethernet
1853 device bfe # Broadcom BCM440x 10/100 Ethernet
1854 device dc # DEC/Intel 21143 and various workalikes
1855 device fxp # Intel EtherExpress PRO/100B (82557, 82558)
1856 device my # Myson Fast Ethernet (MTD80X, MTD89X)
1857 device pcn # AMD Am79C97x PCI 10/100 NICs
1858 device re # RealTek 8139C+/8169
1859 device rl # RealTek 8129/8139
1860 device sbsh # Granch SBNI16 SHDSL modem
1861 device sf # Adaptec AIC-6915 (``Starfire'')
1862 device sis # Silicon Integrated Systems SiS 900/SiS 7016
1863 device ste # Sundance ST201 (D-Link DFE-550TX)
1864 device tl # Texas Instruments ThunderLAN
1865 device tx # SMC EtherPower II (83c17x ``EPIC'')
1866 device vge # VIA 612x GigE
1867 device vr # VIA Rhine, Rhine II
1868 device wb # Winbond W89C840F
1869 device xl # 3Com 3c90x (``Boomerang'', ``Cyclone'')
1871 # PCI Ethernet NICs.
1872 device de # DEC/Intel DC21x4x (``Tulip'')
1873 device txp # 3Com 3cR990 (``Typhoon'')
1874 device vx # 3Com 3c590, 3c595 (``Vortex'')
1876 # Gigabit Ethernet NICs.
1877 device bge # Broadcom BCM570x (``Tigon III'')
1878 device em # Intel Pro/1000 (8254x,8257x)
1880 device emx # Intel Pro/1000 (8257{1,2,3,4})
1882 device ig_hal # Intel Pro/1000 hardware abstraction layer
1883 device et # Agere ET1310 10/100/1000 Ethernet
1884 device lge # Level 1 LXT1001 (``Mercury'')
1885 device mxge # Myricom Myri-10G 10GbE NIC
1886 device nfe # nVidia nForce2/3 MCP04/51/55 CK804
1887 device nge # NatSemi DP83820 and DP83821
1888 device sk # SysKonnect GEnesis, LinkSys EG1023, D-Link
1889 device ti # Alteon (``Tigon I'', ``Tigon II'')
1890 device stge # Sundance/Tamarack TC9021 Gigabit Ethernet
1891 device msk # Marvell/SysKonnect Yukon II Gigabit Ethernet
1892 device jme # JMicron Gigabit/Fast Ethernet
1894 # Brooktree driver has been ported to the new I2C framework. Thus,
1895 # you'll need to have the following 3 lines in the kernel config.
1899 # The iic and smb devices are only needed if you want to control other
1900 # I2C slaves connected to the external connector of some cards.
1903 options BKTR_NEW_MSP34XX_DRIVER
1905 # WinTV PVR-250/350 driver
1911 # pccard: pccard slots
1912 # cardbus/cbb: cardbus bridge
1918 # Laptop/Notebook options:
1921 # apm under `Miscellaneous hardware'
1924 # For older notebooks that signal a powerfail condition (external
1925 # power supply dropped, or battery state low) by issuing an NMI:
1927 options POWERFAIL_NMI # make it beep instead of panicing
1933 # mmcsd MMC/SD memory card
1934 # sdhci Generic PCI SD Host Controller
1943 # System Management Bus support is provided by the 'smbus' device.
1944 # Access to the SMBus device is via the 'smb' device (/dev/smb*),
1945 # which is a child of the 'smbus' device.
1947 # Supported devices:
1948 # smb standard io through /dev/smb*
1950 # Supported SMB interfaces:
1951 # iicsmb I2C to SMB bridge with any iicbus interface
1952 # bktr brooktree848 I2C hardware interface
1953 # intpm Intel PIIX4 (82371AB, 82443MX) Power Management Unit
1954 # alpm Acer Aladdin-IV/V/Pro2 Power Management Unit
1955 # ichsmb Intel ICH SMBus controller chips (82801AA, 82801AB, 82801BA)
1956 # viapm VIA VT82C586B,596,686A and VT8233 SMBus controllers
1957 # amdpm AMD 756 Power Management Unit
1958 # amdsmb AMD 8111 SMBus 2.0 Controller
1960 device smbus # Bus support, required for smb below.
1974 # Philips i2c bus support is provided by the `iicbus' device.
1976 # Supported devices:
1977 # ic i2c network interface
1978 # iic i2c standard io
1979 # iicsmb i2c to smb bridge. Allow i2c i/o with smb commands.
1981 # Supported interfaces:
1982 # pcf Philips PCF8584 ISA-bus controller
1983 # bktr brooktree848 I2C software interface
1986 # iicbb generic I2C bit-banging code (needed by lpbb, bktr)
1988 device iicbus # Bus support, required for ic/iic/iicsmb below.
1993 device iicsmb # smb over i2c bridge
1995 device pcf0 at isa? port 0x320 irq 5
1997 # Intel Core and newer CPUs on-die digital thermal sensor support
2000 # AMD Family 0Fh, 10h and 11h temperature sensors
2004 # ThinkPad Active Protection System accelerometer
2005 device aps0 at isa? port 0x1600
2007 # HW monitoring devices lm(4), it(4) and nsclpcsio.
2008 device lm0 at isa? port 0x290
2009 device it0 at isa? port 0x290
2010 device it1 at isa? port 0xc00
2011 device it2 at isa? port 0xd00
2012 device it3 at isa? port 0x228
2013 device nsclpcsio0 at isa? port 0x2e
2014 device nsclpcsio1 at isa? port 0x4e
2015 device wbsio0 at isa? port 0x2e
2016 device wbsio1 at isa? port 0x4e
2017 device lm#3 at wbsio?
2018 device uguru0 at isa? port 0xe0 # ABIT uGuru
2022 # Parallel port bus support is provided by the `ppbus' device.
2023 # Multiple devices may be attached to the parallel port, devices
2024 # are automatically probed and attached when found.
2026 # Supported devices:
2027 # vpo Iomega Zip Drive
2028 # Requires SCSI disk support ('scbus' and 'da'); the best
2029 # performance is achieved with ports in EPP 1.9 mode.
2030 # lpt Parallel Printer
2031 # plip Parallel network interface
2032 # ppi General-purpose I/O ("Geek Port") + IEEE1284 I/O
2033 # pps Pulse per second Timing Interface
2034 # lpbb Philips official parallel port I2C bit-banging interface
2036 # Supported interfaces:
2037 # ppc ISA-bus parallel port interfaces.
2040 options PPC_PROBE_CHIPSET # Enable chipset specific detection
2041 # (see flags in ppc(4))
2042 options DEBUG_1284 # IEEE1284 signaling protocol debug
2043 options PERIPH_1284 # Makes your computer act as a IEEE1284
2044 # compliant peripheral
2045 options DONTPROBE_1284 # Avoid boot detection of PnP parallel devices
2046 options VP0_DEBUG # ZIP/ZIP+ debug
2047 options LPT_DEBUG # Printer driver debug
2048 options PPC_DEBUG=2 # Parallel chipset level debug
2049 options PLIP_DEBUG # Parallel network IP interface debug
2050 options PCFCLOCK_VERBOSE # Verbose pcfclock driver
2051 options PCFCLOCK_MAX_RETRIES=5 # Maximum read tries (default 10)
2053 device ppc0 at isa? irq 7
2063 # Kernel BOOTP support
2065 options BOOTP # Use BOOTP to obtain IP address/hostname
2066 options BOOTP_NFSROOT # NFS mount root filesystem using BOOTP info
2067 options BOOTP_NFSV3 # Use NFS v3 to NFS mount root
2068 options BOOTP_COMPAT # Workaround for broken bootp daemons.
2069 options BOOTP_WIRED_TO=fxp0 # Use interface fxp0 for BOOTP
2072 # Add tie-ins for a hardware watchdog. This only enable the hooks;
2073 # the user must still supply the actual driver.
2078 # Set the number of PV entries per process. Increasing this can
2079 # stop panics related to heavy use of shared memory. However, that can
2080 # (combined with large amounts of physical memory) cause panics at
2081 # boot time due the kernel running out of VM space.
2083 # If you're tweaking this, you might also want to increase the sysctls
2084 # "vm.v_free_min", "vm.v_free_reserved", and "vm.v_free_target".
2086 # The value below is the one more than the default.
2088 options PMAP_SHPGPERPROC=201
2091 # Change the size of the kernel virtual address space. Due to
2092 # constraints in loader(8) on i386, this must be a multiple of 4.
2093 # 256 = 1 GB of kernel address space. Increasing this also causes
2094 # a reduction of the address space in user processes. 512 splits
2095 # the 4GB cpu address space in half (2GB user, 2GB kernel).
2097 options KVA_PAGES=260
2100 # Disable swapping. This option removes all code which actually performs
2101 # swapping, so it's not possible to turn it back on at run-time.
2103 # This is sometimes usable for systems which don't have any swap space
2104 # (see also sysctls "vm.defer_swapspace_pageouts" and
2105 # "vm.disable_swapspace_pageouts")
2107 #options NO_SWAPPING
2109 # Set the size of the buffer cache KVM reservation, in buffers. This is
2110 # scaled by approximately 16384 bytes. The system will auto-size the buffer
2111 # cache if this option is not specified.
2115 # Set the size of the mbuf KVM reservation, in clusters. This is scaled
2116 # by approximately 2048 bytes. The system will auto-size the mbuf area
2117 # to (512 + maxusers*16) if this option is not specified.
2118 # maxusers is in turn computed at boot time depending on available memory
2119 # or set to the value specified by "options MAXUSERS=x" (x=0 means
2121 # So, to take advantage of autoscaling, you have to remove both
2122 # NMBCLUSTERS and MAXUSERS (and NMBUFS) from your kernel config.
2124 options NMBCLUSTERS=1024
2126 # Set the number of mbufs available in the system. Each mbuf
2127 # consumes 256 bytes. The system will autosize this (to 4 times
2128 # the number of NMBCLUSTERS, depending on other constraints)
2129 # if this option is not specified.
2133 # Tune the buffer cache maximum KVA reservation, in bytes. The maximum is
2134 # usually capped at 200 MB, effecting machines with > 1GB of ram. Note
2135 # that the buffer cache only really governs write buffering and disk block
2136 # translations. The VM page cache is our primary disk cache and is not
2137 # effected by the size of the buffer cache.
2139 options VM_BCACHE_SIZE_MAX="(100*1024*1024)"
2141 # Tune the swap zone KVA reservation, in bytes. The default is typically
2142 # 70 MB, giving the system the ability to manage a maximum of 28GB worth
2143 # of swapped out data.
2145 options VM_SWZONE_SIZE_MAX="(50*1024*1024)"
2148 # Enable extra debugging code for locks. This stores the filename and
2149 # line of whatever acquired the lock in the lock itself, and change a
2150 # number of function calls to pass around the relevant data. This is
2151 # not at all useful unless you are debugging lock code. Also note
2152 # that it is likely to break e.g. fstat(1) unless you recompile your
2153 # userland with -DDEBUG_LOCKS as well.
2155 # DEBUG_LOCKS_LATENCY adds a sysctl to add a forced latency loop
2156 # (count to N) in front of any spinlock or gettoken.
2159 options DEBUG_LOCKS_LATENCY
2161 # Set the amount of time (in seconds) the system will wait before
2162 # rebooting automatically when a kernel panic occurs. If set to (-1),
2163 # the system will wait indefinitely until a key is pressed on the
2165 options PANIC_REBOOT_WAIT_TIME=16
2167 # Attempt to bypass the buffer cache and put data directly into the
2168 # userland buffer for read operation when O_DIRECT flag is set on the
2169 # file. Both offset and length of the read operation must be
2170 # multiples of the physical media sector size.
2174 # Specify a lower limit for the number of swap I/O buffers. They are
2175 # (among other things) used when bypassing the buffer cache due to
2176 # DIRECTIO kernel option enabled and O_DIRECT flag set on file.
2178 #options NSWBUF_MIN=120
2180 # The 'asr' driver provides support for current DPT/Adaptec SCSI RAID
2181 # controllers (SmartRAID V and VI and later).
2182 # These controllers require the CAM infrastructure.
2187 # The 'dpt' driver provides support for DPT controllers (http://www.dpt.com/).
2188 # These have hardware RAID-{0,1,5} support, and do multi-initiator I/O.
2189 # The DPT controllers are commonly re-licensed under other brand-names -
2190 # some controllers by Olivetti, Dec, HP, AT&T, SNI, AST, Alphatronic, NEC and
2191 # Compaq are actually DPT controllers.
2193 # See src/sys/dev/raid/dpt for debugging and other subtle options.
2194 # DPT_MEASURE_PERFORMANCE Enables a set of (semi)invasive metrics. Various
2195 # instruments are enabled. The tools in
2196 # /usr/sbin/dpt_* assume these to be enabled.
2197 # DPT_HANDLE_TIMEOUTS Normally device timeouts are handled by the DPT.
2198 # If you ant the driver to handle timeouts, enable
2199 # this option. If your system is very busy, this
2200 # option will create more trouble than solve.
2201 # DPT_TIMEOUT_FACTOR Used to compute the excessive amount of time to
2202 # wait when timing out with the above option.
2203 # DPT_DEBUG_xxxx These are controllable from sys/dev/raid/dpt/dpt.h
2204 # DPT_LOST_IRQ When enabled, will try, once per second, to catch
2205 # any interrupt that got lost. Seems to help in some
2206 # DPT-firmware/Motherboard combinations. Minimal
2207 # cost, great benefit.
2208 # DPT_RESET_HBA Make "reset" actually reset the controller
2209 # instead of fudging it. Only enable this if you
2210 # are 100% certain you need it.
2215 #!CAM# options DPT_MEASURE_PERFORMANCE
2216 #!CAM# options DPT_HANDLE_TIMEOUTS
2217 options DPT_TIMEOUT_FACTOR=4
2218 options DPT_LOST_IRQ
2219 options DPT_RESET_HBA
2222 # Compaq "CISS" RAID controllers (SmartRAID 5* series)
2223 # These controllers have a SCSI-like interface, and require the
2224 # CAM infrastructure.
2229 # Intel Integrated RAID controllers.
2230 # This driver is supported and maintained by
2231 # "Leubner, Achim" <Achim_Leubner@adaptec.com>.
2236 # Mylex AcceleRAID and eXtremeRAID controllers with v6 and later
2237 # firmware. These controllers have a SCSI-like interface, and require
2238 # the CAM infrastructure.
2249 # General USB code (mandatory for USB)
2256 # Generic USB device driver
2258 # Human Interface Device (anything with buttons and dials)
2264 # USB Iomega Zip 100 Drive (Requires scbus and da)
2270 # USB Rio (MP3 Player)
2290 # ADMtek USB ethernet. Supports the LinkSys USB100TX,
2291 # the Billionton USB100, the Melco LU-ATX, the D-Link DSB-650TX
2292 # and the SMC 2202USB. Also works with the ADMtek AN986 Pegasus
2296 # ASIX Electronics AX88172 USB 2.0 ethernet driver. Used in the
2297 # LinkSys USB200M and various other adapters.
2300 # CATC USB-EL1201A USB ethernet. Supports the CATC Netmate
2301 # and Netmate II, and the Belkin F5U111.
2304 # Kawasaki LSI ethernet. Supports the LinkSys USB10T,
2305 # Entrega USB-NET-E45, Peracom Ethernet Adapter, the
2306 # 3Com 3c19250, the ADS Technologies USB-10BT, the ATen UC10T,
2307 # the Netgear EA101, the D-Link DSB-650, the SMC 2102USB
2308 # and 2104USB, and the Corega USB-T.
2311 # USB CDC ethernet. Supports the LG P-500 smartphone.
2314 # RealTek 8150 based USB ethernet device:
2316 # GREEN HOUSE GH-USB100B
2317 # Billionton ThumbLAN USBKR2-100B
2320 # USB wireless NICs, requires wlan_amrr
2322 # Ralink Technology RT2501USB/RT2601USB
2325 # Ralink Technology RT2500USB
2328 # debugging options for the USB subsystem
2333 options UKBD_DFLT_KEYMAP # specify the built-in keymap
2334 makeoptions UKBD_DFLT_KEYMAP=it.iso
2337 device firewire # Firewire bus code
2338 device sbp # SCSI over Firewire (Requires scbus and da)
2339 device fwe # Ethernet over Firewire (non-standard!)
2341 # dcons support (Dumb Console Device)
2342 device dcons # dumb console driver
2343 device dcons_crom # FireWire attachment
2344 options DCONS_BUF_SIZE=16384 # buffer size
2345 options DCONS_POLL_HZ=100 # polling rate
2346 options DCONS_FORCE_CONSOLE=1 # force to be the primary console
2347 options DCONS_FORCE_GDB=1 # force to be the gdb device
2349 #####################################################################
2352 # This is a port of the openbsd crypto framework. Include this when
2353 # configuring IPsec and when you have a h/w crypto device to accelerate
2354 # user applications that link to openssl.
2356 # Drivers are ports from openbsd with some simple enhancements that have
2357 # been fed back to openbsd (and hopefully will be included).
2359 pseudo-device crypto # core crypto support
2360 pseudo-device cryptodev # /dev/crypto for access to h/w
2362 device rndtest # FIPS 140-2 entropy tester
2364 device hifn # Hifn 7951, 7781, etc.
2365 options HIFN_DEBUG # enable debugging support: hw.hifn.debug
2366 #options HIFN_NO_RNG # for devices without RNG
2367 options HIFN_RNDTEST # enable rndtest support
2369 device safe # SafeNet 1141
2370 options SAFE_DEBUG # enable debugging support: hw.safe.debug
2371 #options SAFE_NO_RNG # for devices without RNG
2372 options SAFE_RNDTEST # enable rndtest support
2374 device ubsec # Broadcom 5501, 5601, 58xx
2375 options UBSEC_DEBUG # enable debugging support: hw.ubsec.debug
2376 #options UBSEC_NO_RNG # for devices without RNG
2377 options UBSEC_RNDTEST # enable rndtest support
2379 device aesni # hardware crypto/RNG for AES-NI
2380 device glxsb # Geode LX Security Block
2381 device padlock # hardware crypto/RNG for VIA C3/C7/Eden
2382 device rdrand # hardware RNG for RdRand
2385 # ACPI support using the Intel ACPI Component Architecture reference
2388 # ACPI_DEBUG enables the use of the debug.acpi.level and debug.acpi.layer
2389 # kernel environment variables to select initial debugging levels for the
2390 # Intel ACPICA code.
2392 # Note that building ACPI into the kernel is deprecated; the module is
2393 # normally loaded automatically by the loader.
2398 # ACPI WMI Mapping driver
2401 # ACPI Asus Extras (LCD backlight/brightness, video output, etc.)
2404 # ACPI Fujitsu Extras (Buttons)
2407 # ACPI extras driver for HP laptops
2410 # ACPI Panasonic Extras (LCD backlight/brightness, video output, etc.)
2411 device acpi_panasonic
2413 # ACPI Sony extra (LCD brightness)
2416 # ACPI extras driver for ThinkPad laptops
2417 device acpi_thinkpad
2419 # ACPI Toshiba Extras (LCD backlight/brightness, video output, etc.)
2422 # ACPI Video Extensions (LCD backlight/brightness, video output, etc.)
2425 device aibs # ASUSTeK AI Booster (ACPI ASOC ATK0110)
2426 device pmtimer # adjust the system clock after resume
2429 # drm: General DRM code
2430 # i915drm: Intel i830, i845, i915, i945, i965, G33/35
2431 # mach64drm: ATI Mach64 cards - Rage and 3D Rage series
2432 # mgadrm: AGP Matrox G200, G400, G450, G550
2433 # r128drm: ATI Rage 128 cards
2434 # radeondrm: ATI Radeon cards
2435 # savagedrm: Savage cards
2437 # tdfxdrm: 3dfx Voodoo 3/4/5 and Banshee
2439 # DRM_DEBUG: include debug printfs, very slow
2441 # DRM requires AGP in the kernel.
2459 device cmx # Omnikey CardMan 4040 smartcard reader
2460 device gpio # Enable support for the gpio framework
2461 device tbridge # regression testing
2464 # Embedded system options:
2466 # An embedded system might want to run something other than init.
2467 options INIT_PATH="/sbin/init:/sbin/oinit"
2470 options BUS_DEBUG # enable newbus debugging
2471 options NPX_DEBUG # enable npx debugging (FPU/math emu)
2472 options RSS_DEBUG # enable RSS (Receive Side Scaling) debugging
2474 # Record the program counter of the code interrupted by the statistics
2475 # clock interrupt. Use pctrack(8) to dump this information.
2476 options DEBUG_PCTRACK
2478 # More undocumented options for linting.
2479 # Note that documenting these are not considered an affront.
2481 #options ACPI_NO_SEMAPHORES
2482 options AHC_DUMP_EEPROM
2483 #options BKTR_ALLOC_PAGES=xxx
2484 options CAM_DEBUG_DELAY
2485 options CLUSTERDEBUG
2486 options COMPAT_LINUX
2487 options COMPAT_SUNOS
2489 options DEBUG_CRIT_SECTIONS
2490 options DEBUG_INTERRUPTS
2491 #options DISABLE_PSE
2493 options EMX_RSS_DEBUG
2494 options JME_RSS_DEBUG
2495 #options ED_NO_MIIBUS
2496 options ENABLE_ALART
2498 options FB_INSTALL_CDEV
2499 options FE_8BIT_SUPPORT
2500 options I586_PMC_GUPROF=0x70000
2501 #options IEEE80211_DEBUG_REFCNT
2502 options IEEE80211_SUPPORT_SUPERG
2503 options KBDIO_DEBUG=10
2504 options KBD_MAXRETRY=4
2505 options KBD_MAXWAIT=6
2506 options KBD_RESETDELAY=201
2507 options KERN_TIMESTAMP
2511 #options MAXFILES=xxx
2516 options SCSI_NCR_DEBUG
2517 options SCSI_NCR_MAX_SYNC=10000
2518 options SCSI_NCR_MAX_WIDE=1
2519 options SCSI_NCR_MYADDR=7
2520 options SHOW_BUSYBUFS # List buffers that prevent root unmount
2523 options SLIP_IFF_OPTS
2524 options SOCKBUF_DEBUG
2525 options TDMA_BINTVAL_DEFAULT=5
2526 options TDMA_SLOTCNT_DEFAULT=2
2527 options TDMA_SLOTLEN_DEFAULT=10*1000
2528 options TDMA_TXRATE_11A_DEFAULT=2*24
2529 options TDMA_TXRATE_11B_DEFAULT=2*11
2530 options TDMA_TXRATE_11G_DEFAULT=2*24
2531 options TDMA_TXRATE_11NA_DEFAULT="(4|IEEE80211_RATE_MCS)"
2532 options TDMA_TXRATE_11NG_DEFAULT="(4|IEEE80211_RATE_MCS)"
2533 options TDMA_TXRATE_HALF_DEFAULT=2*12
2534 options TDMA_TXRATE_QUARTER_DEFAULT=2*6
2535 options TDMA_TXRATE_TURBO_DEFAULT=2*24
2536 options TIMER_FREQ="((14318182+6)/12)"
2537 options VFS_BIO_DEBUG
2538 options VM_PAGE_DEBUG
2543 options KTR_ENTRIES=1024
2544 options KTR_VERBOSE=1
2546 #options KTR_DMCRYPT
2547 #options KTR_DSCHED_BFQ
2548 #options KTR_ETHERNET
2554 #options KTR_IF_START
2556 #options KTR_KERNENTRY
2558 #options KTR_POLLING
2559 #options KTR_SERIALIZER
2560 #options KTR_SPIN_CONTENTION
2561 #options KTR_TESTLOG
2564 #options KTR_USB_MEMORY
2567 options ALTQ #alternate queueing
2568 options ALTQ_CBQ #class based queueing
2569 options ALTQ_RED #random early detection
2570 options ALTQ_RIO #triple red for diffserv (needs RED)
2571 options ALTQ_HFSC #hierarchical fair service curve
2572 options ALTQ_PRIQ #priority queue
2573 options ALTQ_FAIRQ #fair queue
2574 #options ALTQ_NOPCC #don't use processor cycle counter
2575 options ALTQ_DEBUG #for debugging
2576 # you might want to set kernel timer to 1kHz if you use CBQ,
2577 # especially with 100baseT
2583 options SCTP_USE_ADLER32
2584 options SCTP_HIGH_SPEED
2585 options SCTP_STAT_LOGGING
2586 options SCTP_CWND_LOGGING
2587 options SCTP_BLK_LOGGING
2588 options SCTP_STR_LOGGING
2589 options SCTP_FR_LOGGING
2590 options SCTP_MAP_LOGGING
2598 options WATCHDOG_ENABLE # Enable watchdog support framework
2599 options WDOG_DISABLE_ON_PANIC # Automatically disable watchdogs on panic
2602 options ERROR_LED_ON_PANIC # If an error led is present, light it up on panic