2 * Copyright (c) 2014 The DragonFly Project. All rights reserved.
4 * This code is derived from software contributed to The DragonFly Project
5 * by Matthew Dillon <dillon@backplane.com>
7 * Redistribution and use in source and binary forms, with or without
8 * modification, are permitted provided that the following conditions
11 * 1. Redistributions of source code must retain the above copyright
12 * notice, this list of conditions and the following disclaimer.
13 * 2. Redistributions in binary form must reproduce the above copyright
14 * notice, this list of conditions and the following disclaimer in
15 * the documentation and/or other materials provided with the
17 * 3. Neither the name of The DragonFly Project nor the names of its
18 * contributors may be used to endorse or promote products derived
19 * from this software without specific, prior written permission.
21 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
22 * ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
23 * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
24 * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
25 * COPYRIGHT HOLDERS OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
26 * INCIDENTAL, SPECIAL, EXEMPLARY OR CONSEQUENTIAL DAMAGES (INCLUDING,
27 * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
28 * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
29 * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
30 * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT
31 * OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
35 * Intel 4th generation mobile cpus integrated I2C device.
37 * Datasheet reference: Section 22.
39 * http://www.intel.com/content/www/us/en/processors/core/4th-gen-core-family-mobile-i-o-datasheet.html?wapkw=datasheets+4th+generation
41 * This is a from-scratch driver under the BSD license using the Intel data
42 * sheet and the linux driver for reference. All code is freshly written
43 * without referencing the linux driver code. However, during testing
44 * I am also using the linux driver code as a reference to help resolve any
45 * issues that come. These will be specifically documented in the code.
47 * Please see protocol notes in section 5.21. This controller is an I2C
48 * master only and cannot act as a slave. The IO voltage should be set by
49 * the BIOS. Standard (100Kb/s) and Fast (400Kb/s) and fast mode plus
50 * (1MB/s) is supported. High speed mode (3.4 MB/s) is NOT supported.
53 #ifndef _BUS_SMBUS_INTELGEN4_IG4_REG_H_
54 #define _BUS_SMBUS_INTELGEN4_IG4_REG_H_
57 * 22.2 MMIO registers can be accessed through BAR0 in PCI mode or through
58 * BAR1 when in ACPI mode.
60 * Register width is 32-bits
62 * 22.2 Default Values on device reset are 0 except as specified here:
64 * SS_SCL_HCNT 0x00000264
65 * SS_SCL_LCNT 0x000002C2
66 * FS_SCL_HCNT 0x0000006E
67 * FS_SCL_LCNT 0x000000CF
68 * INTR_MASK 0x000008FF
71 * SDA_SETUP 0x00000064
72 * COMP_PARAM1 0x00FFFF6E
76 #define IG4_REG_CTL 0x0000 /* RW Control Register */
77 #define IG4_REG_TAR_ADD 0x0004 /* RW Target Address */
78 #define IG4_REG_DATA_CMD 0x0010 /* RW Data Buffer and Command */
79 #define IG4_REG_SS_SCL_HCNT 0x0014 /* RW Std Speed clock High Count */
80 #define IG4_REG_SS_SCL_LCNT 0x0018 /* RW Std Speed clock Low Count */
81 #define IG4_REG_FS_SCL_HCNT 0x001C /* RW Fast Speed clock High Count */
82 #define IG4_REG_FS_SCL_LCNT 0x0020 /* RW Fast Speed clock Low Count */
83 #define IG4_REG_INTR_STAT 0x002C /* RO Interrupt Status */
84 #define IG4_REG_INTR_MASK 0x0030 /* RW Interrupt Mask */
85 #define IG4_REG_RAW_INTR_STAT 0x0034 /* RO Raw Interrupt Status */
86 #define IG4_REG_RX_TL 0x0038 /* RW Receive FIFO Threshold */
87 #define IG4_REG_TX_TL 0x003C /* RW Transmit FIFO Threshold */
88 #define IG4_REG_CLR_INTR 0x0040 /* RO Clear Interrupt */
89 #define IG4_REG_CLR_RX_UNDER 0x0044 /* RO Clear RX_Under Interrupt */
90 #define IG4_REG_CLR_RX_OVER 0x0048 /* RO Clear RX_Over Interrupt */
91 #define IG4_REG_CLR_TX_OVER 0x004C /* RO Clear TX_Over Interrupt */
92 #define IG4_REG_CLR_TX_ABORT 0x0054 /* RO Clear TX_Abort Interrupt */
93 #define IG4_REG_CLR_ACTIVITY 0x005C /* RO Clear Activity Interrupt */
94 #define IG4_REG_CLR_STOP_DET 0x0060 /* RO Clear STOP Detection Int */
95 #define IG4_REG_CLR_START_DET 0x0064 /* RO Clear START Detection Int */
96 #define IG4_REG_CLR_GEN_CALL 0x0068 /* RO Clear General Call Interrupt */
97 #define IG4_REG_I2C_EN 0x006C /* RW I2C Enable */
98 #define IG4_REG_I2C_STA 0x0070 /* RO I2C Status */
99 #define IG4_REG_TXFLR 0x0074 /* RO Transmit FIFO Level */
100 #define IG4_REG_RXFLR 0x0078 /* RO Receive FIFO Level */
101 #define IG4_REG_SDA_HOLD 0x007C /* RW SDA Hold Time Length */
102 #define IG4_REG_TX_ABRT_SOURCE 0x0080 /* RO Transmit Abort Source */
103 #define IG4_REG_SLV_DATA_NACK 0x0084 /* RW General Slave Data NACK */
104 #define IG4_REG_DMA_CTRL 0x0088 /* RW DMA Control */
105 #define IG4_REG_DMA_TDLR 0x008C /* RW DMA Transmit Data Level */
106 #define IG4_REG_DMA_RDLR 0x0090 /* RW DMA Receive Data Level */
107 #define IG4_REG_SDA_SETUP 0x0094 /* RW SDA Setup */
108 #define IG4_REG_ENABLE_STATUS 0x009C /* RO Enable Status */
109 #define IG4_REG_COMP_PARAM1 0x00F4 /* RO Component Parameter */
110 #define IG4_REG_COMP_VER 0x00F8 /* RO Component Version */
111 #define IG4_REG_COMP_TYPE 0x00FC /* RO Probe width/endian? (linux) */
112 #define IG4_REG_CLK_PARMS 0x0800 /* RW Clock Parameters */
113 #define IG4_REG_RESETS 0x0804 /* RW Reset Register */
114 #define IG4_REG_GENERAL 0x0808 /* RW General Register */
115 #define IG4_REG_SW_LTR_VALUE 0x0810 /* RW SW LTR Value */
116 #define IG4_REG_AUTO_LTR_VALUE 0x0814 /* RW Auto LTR Value */
119 * CTL - Control Register 22.2.1
120 * Default Value: 0x0000007F.
122 * RESTARTEN - RW Restart Enable
123 * 10BIT - RW Controller operates in 10-bit mode, else 7-bit
125 * NOTE: When restart is disabled the controller is incapable of
126 * performing the following functions:
128 * Sending a START Byte
129 * Performing any high-speed mode op
130 * Performing direction changes in combined format mode
131 * Performing a read operation with a 10-bit address
133 * Attempting to perform the above operations will result in the
134 * TX_ABORT bit being set in RAW_INTR_STAT.
136 #define IG4_CTL_SLAVE_DISABLE 0x0040 /* snarfed from linux */
137 #define IG4_CTL_RESTARTEN 0x0020 /* Allow Restart when master */
138 #define IG4_CTL_10BIT 0x0010 /* ctlr accepts 10-bit addresses */
139 #define IG4_CTL_SPEED_FAST 0x0004 /* snarfed from linux */
140 #define IG4_CTL_SPEED_STD 0x0002 /* snarfed from linux */
141 #define IG4_CTL_MASTER 0x0001 /* snarfed from linux */
144 * TAR_ADD - Target Address Register 22.2.2
145 * Default Value: 0x00000055F
147 * 10BIT - RW controller starts its transfers in 10-bit
148 * address mode, else 7-bit.
150 * SPECIAL - RW Indicates whether software performs a General Call
151 * or START BYTE command.
153 * 0 Ignore GC_OR_START and use TAR address.
155 * 1 Perform special I2C Command based on GC_OR_START.
157 * GC_OR_START - RW (only if SPECIAL is set)
159 * 0 General Call Address. After issuing a General Call,
160 * only writes may be performed. Attempting to issue
161 * a read command results in IX_ABRT in RAW_INTR_STAT.
162 * The controller remains in General Call mode until
163 * bit 11 (SPECIAL) is cleared.
168 * IC_TAR - RW when transmitting a general call, these bits are
169 * ignored. To generate a START BYTE, the address
170 * needs to be written into these bits once.
172 * This register should only be updated when the IIC is disabled (I2C_ENABLE=0)
174 #define IG4_TAR_10BIT 0x1000 /* start xfer in 10-bit mode */
175 #define IG4_TAR_SPECIAL 0x0800 /* Perform special command */
176 #define IG4_TAR_GC_OR_START 0x0400 /* General Call or Start */
177 #define IG4_TAR_ADDR_MASK 0x03FF /* Target address */
180 * TAR_DATA_CMD - Data Buffer and Command Register 22.2.3
182 * RESTART - RW This bit controls whether a forced RESTART is
183 * issued before the byte is sent or received.
185 * 0 If not set a RESTART is only issued if the tranfer
186 * direction is changing from the previous command.
188 * 1 A RESTART is issued before the byte is sent or
189 * received, regardless of whether or not the transfer
190 * direction is changing from the previous command.
192 * STOP - RW This bit controls whether a STOP is issued after
193 * the byte is sent or received.
195 * 0 STOP is not issued after this byte, regardless
196 * of whether or not the Tx FIFO is empty.
198 * 1 STOP is issued after this byte, regardless of
199 * whether or not the Tx FIFO is empty. If the
200 * Tx FIFO is not empty the master immediately tries
201 * to start a new transfer by issuing a START and
202 * arbitrating for the bus.
204 * i.e. the STOP is issued along with this byte,
205 * within the write stream.
207 * COMMAND - RW Control whether a read or write is performed.
213 * DATA (7:0) - RW Contains the data to be transmitted or received
216 * NOTE: Writing to this register causes a START + slave + RW to be
217 * issued if the direction has changed or the last data byte was
220 * NOTE: We control termination? so this register must be written
221 * for each byte we wish to receive. We can then drain the
225 #define IG4_DATA_RESTART 0x0400 /* Force RESTART */
226 #define IG4_DATA_STOP 0x0200 /* Force STOP[+START] */
227 #define IG4_DATA_COMMAND_RD 0x0100 /* bus direction 0=write 1=read */
228 #define IG4_DATA_MASK 0x00FF
231 * SS_SCL_HCNT - Standard Speed Clock High Count Register 22.2.4
232 * SS_SCL_LCNT - Standard Speed Clock Low Count Register 22.2.5
233 * FS_SCL_HCNT - Fast Speed Clock High Count Register 22.2.6
234 * FS_SCL_LCNT - Fast Speed Clock Low Count Register 22.2.7
236 * COUNT (15:0) - Set the period count to a value between 6 and
239 #define IG4_SCL_CLOCK_MASK 0xFFFFU /* count bits in register */
242 * INTR_STAT - (RO) Interrupt Status Register 22.2.8
243 * INTR_MASK - (RW) Interrupt Mask Register 22.2.9
244 * RAW_INTR_STAT- (RO) Raw Interrupt Status Register 22.2.10
246 * GEN_CALL Set only when a general call (broadcast) address
247 * is received and acknowleged, stays set until
248 * cleared by reading CLR_GEN_CALL.
250 * START_DET Set when a START or RESTART condition has occurred
253 * STOP_DET Set when a STOP condition has occurred on the
256 * ACTIVITY Set by any activity on the interface. Cleared
257 * by reading CLR_ACTIVITY or CLR_INTR.
259 * TX_ABRT Indicates the controller as a transmitter is
260 * unable to complete the intended action. When set,
261 * the controller will hold the TX FIFO in a reset
262 * state (flushed) until CLR_TX_ABORT is read to
263 * clear the condition. Once cleared, the TX FIFO
264 * will be available again.
266 * TX_EMPTY Indicates that the transmitter is at or below
267 * the specified TX_TL threshold. Automatically
268 * cleared by HW when the buffer level goes above
271 * TX_OVER Indicates that the processer attempted to write
272 * to the TX FIFO while the TX FIFO was full. Cleared
273 * by reading CLR_TX_OVER.
275 * RX_FULL Indicates that the receive FIFO has reached or
276 * exceeded the specified RX_TL threshold. Cleared
277 * by HW when the cpu drains the FIFO to below the
280 * RX_OVER Indicates that the receive FIFO was unable to
281 * accept new data and data was lost. Cleared by
282 * reading CLR_RX_OVER.
284 * RX_UNDER Indicates that the cpu attempted to read data
285 * from the receive buffer while the RX FIFO was
286 * empty. Cleared by reading CLR_RX_UNDER.
288 * NOTES ON RAW_INTR_STAT:
290 * This register can be used to monitor the GEN_CALL, START_DET,
291 * STOP_DET, ACTIVITY, TX_ABRT, TX_EMPTY, TX_OVER, RX_FULL, RX_OVER,
292 * and RX_UNDER bits. The documentation is a bit unclear but presumably
293 * this is the unlatched version.
295 * Code should test FIFO conditions using the I2C_STA (status) register,
296 * not the interrupt status registers.
299 #define IG4_INTR_GEN_CALL 0x0800
300 #define IG4_INTR_START_DET 0x0400
301 #define IG4_INTR_STOP_DET 0x0200
302 #define IG4_INTR_ACTIVITY 0x0100
303 #define IG4_INTR_TX_ABRT 0x0040
304 #define IG4_INTR_TX_EMPTY 0x0010
305 #define IG4_INTR_TX_OVER 0x0008
306 #define IG4_INTR_RX_FULL 0x0004
307 #define IG4_INTR_RX_OVER 0x0002
308 #define IG4_INTR_RX_UNDER 0x0001
311 * RX_TL - (RW) Receive FIFO Threshold Register 22.2.11
312 * TX_TL - (RW) Transmit FIFO Threshold Register 22.2.12
314 * Specify the receive and transmit FIFO threshold register. The
315 * FIFOs have 16 elements. The valid range is 0-15. Setting a
316 * value greater than 15 causes the actual value to be the maximum
319 * Generally speaking since everything is messaged, we can use a
320 * mid-level setting for both parameters and (e.g.) fully drain the
321 * receive FIFO on the STOP_DET condition to handle loose ends.
323 #define IG4_FIFO_MASK 0x00FF
324 #define IG4_FIFO_LIMIT 16
327 * CLR_INTR - (RO) Clear Interrupt Register 22.2.13
328 * CLR_RX_UNDER - (RO) Clear Interrupt Register (specific) 22.2.14
329 * CLR_RX_OVER - (RO) Clear Interrupt Register (specific) 22.2.15
330 * CLR_TX_OVER - (RO) Clear Interrupt Register (specific) 22.2.16
331 * CLR_TX_ABORT - (RO) Clear Interrupt Register (specific) 22.2.17
332 * CLR_ACTIVITY - (RO) Clear Interrupt Register (specific) 22.2.18
333 * CLR_STOP_DET - (RO) Clear Interrupt Register (specific) 22.2.19
334 * CLR_START_DET- (RO) Clear Interrupt Register (specific) 22.2.20
335 * CLR_GEN_CALL - (RO) Clear Interrupt Register (specific) 22.2.21
337 * CLR_* specific operations clear the appropriate bit in the
338 * RAW_INTR_STAT register. Intel does not really document whether
339 * these operations clear the normal interrupt status register.
341 * CLR_INTR clears bits in the normal interrupt status register and
342 * presumably also the raw(?) register? Intel is again unclear.
344 * NOTE: CLR_INTR only clears software-clearable interrupts. Hardware
345 * clearable interrupts are controlled entirely by the hardware.
346 * CLR_INTR also clears the TX_ABRT_SOURCE register.
348 * NOTE: CLR_TX_ABORT also clears the TX_ABRT_SOURCE register and releases
349 * the TX FIFO from its flushed/reset state, allowing more writes
352 * NOTE: CLR_ACTIVITY has no effect if the I2C bus is still active.
353 * Intel documents that the bit is automatically cleared when
354 * there is no further activity on the bus.
356 #define IG4_CLR_BIT 0x0001 /* Reflects source */
359 * I2C_EN - (RW) I2C Enable Register 22.2.22
361 * ABORT Software can abort an I2C transfer by setting this
362 * bit. Hardware will clear the bit once the STOP has
363 * been detected. This bit can only be set while the
364 * I2C interface is enabled.
366 * I2C_ENABLE Enable the controller, else disable it.
367 * (Use I2C_ENABLE_STATUS to poll enable status
368 * & wait for changes)
370 #define IG4_I2C_ABORT 0x0002
371 #define IG4_I2C_ENABLE 0x0001
374 * I2C_STA - (RO) I2C Status Register 22.2.23
376 #define IG4_STATUS_ACTIVITY 0x0020 /* Controller is active */
377 #define IG4_STATUS_RX_FULL 0x0010 /* RX FIFO completely full */
378 #define IG4_STATUS_RX_NOTEMPTY 0x0008 /* RX FIFO not empty */
379 #define IG4_STATUS_TX_EMPTY 0x0004 /* TX FIFO completely empty */
380 #define IG4_STATUS_TX_NOTFULL 0x0002 /* TX FIFO not full */
381 #define IG4_STATUS_I2C_ACTIVE 0x0001 /* I2C bus is active */
384 * TXFLR - (RO) Transmit FIFO Level Register 22.2.24
385 * RXFLR - (RO) Receive FIFO Level Register 22.2.25
387 * Read the number of entries currently in the Transmit or Receive
388 * FIFOs. Note that for some reason the mask is 9 bits instead of
389 * the 8 bits the fill level controls.
391 #define IG4_FIFOLVL_MASK 0x001F
394 * SDA_HOLD - (RW) SDA Hold Time Length Register 22.2.26
396 * Set the SDA hold time length register in I2C clocks.
398 #define IG4_SDA_HOLD_MASK 0x00FF
401 * TX_ABRT_SOURCE- (RO) Transmit Abort Source Register 22.2.27
403 * Indicates the cause of a transmit abort. This can indicate a
404 * software programming error or a device expected address width
405 * mismatch or other issues. The NORESTART conditions and GENCALL_NOACK
406 * can only occur if a programming error was made in the driver software.
408 * In particular, it should be possible to detect whether any devices
409 * are on the bus by observing the GENCALL_READ status, and it might
410 * be possible to detect ADDR7 vs ADDR10 mismatches.
412 #define IG4_ABRTSRC_TRANSFER 0x00010000 /* Abort initiated by user */
413 #define IG4_ABRTSRC_ARBLOST 0x00001000 /* Arbitration lost */
414 #define IG4_ABRTSRC_NORESTART_10 0x00000400 /* RESTART disabled */
415 #define IG4_ABRTSRC_NORESTART_START 0x00000200 /* RESTART disabled */
416 #define IG4_ABRTSRC_ACKED_START 0x00000080 /* Improper acked START */
417 #define IG4_ABRTSRC_GENCALL_NOACK 0x00000020 /* Improper GENCALL */
418 #define IG4_ABRTSRC_GENCALL_READ 0x00000010 /* Nobody acked GENCALL */
419 #define IG4_ABRTSRC_TXNOACK_DATA 0x00000008 /* data phase no ACK */
420 #define IG4_ABRTSRC_TXNOACK_ADDR10_2 0x00000004 /* addr10/1 phase no ACK */
421 #define IG4_ABRTSRC_TXNOACK_ADDR10_1 0x00000002 /* addr10/2 phase no ACK */
422 #define IG4_ABRTSRC_TXNOACK_ADDR7 0x00000001 /* addr7 phase no ACK */
425 * SLV_DATA_NACK - (RW) Generate Slave DATA NACK Register 22.2.28
427 * When the controller is a receiver a NACK can be generated on
430 * NACK_GENERATE Set to 0 for normal NACK/ACK generation.
431 * Set to 1 to generate a NACK after next data
435 #define IG4_NACK_GENERATE 0x0001
438 * DMA_CTRL - (RW) DMA Control Register 22.2.29
440 * Enables DMA on the transmit and/or receive DMA channel.
442 #define IG4_TX_DMA_ENABLE 0x0002
443 #define IG4_RX_DMA_ENABLE 0x0001
446 * DMA_TDLR - (RW) DMA Transmit Data Level Register 22.2.30
447 * DMA_RDLR - (RW) DMA Receive Data Level Register 22.2.31
449 * Similar to RX_TL and TX_TL but controls when a DMA burst occurs
450 * to empty or fill the FIFOs. Use the same IG4_FIFO_MASK and
451 * IG4_FIFO_LIMIT defines for RX_RL and TX_TL.
456 * SDA_SETUP - (RW) SDA Setup Time Length Register 22.2.32
458 * Set the SDA setup time length register in I2C clocks.
459 * The register must be programmed with a value >=2.
460 * (Defaults to 0x64).
462 #define IG4_SDA_SETUP_MASK 0x00FF
465 * ACK_GEN_CALL - (RW) ACK General Call Register 22.2.33
467 * Control whether the controller responds with a ACK or NACK when
468 * it receives an I2C General Call address.
470 * If set to 0 a NACK is generated and a General Call interrupt is
471 * NOT generated. Otherwise an ACK + interrupt is generated.
473 #define IG4_ACKGC_ACK 0x0001
476 * ENABLE_STATUS - (RO) Enable Status Registger 22.2.34
478 * DATA_LOST - Indicates that a slave receiver operation has
479 * been aborted with at least one data byte received
480 * from a transfer due to the I2C controller being
481 * disabled (IG4_I2C_ENABLE -> 0)
483 * ENABLED - Intel documentation is lacking but I assume this
484 * is a reflection of the IG4_I2C_ENABLE bit in the
488 #define IG4_ENASTAT_DATA_LOST 0x0004
489 #define IG4_ENASTAT_ENABLED 0x0001
492 * COMP_PARAM1 - (RO) Component Parameter Register 22.2.35
493 * Default Value 0x00FFFF6E
495 * VALID - Intel documentation is unclear but I believe this
496 * must be read as a 1 to indicate that the rest of
497 * the bits in the register are valid.
499 * HASDMA - Indicates that the chip is DMA-capable. Presumably
500 * in certain virtualization cases the chip might be
501 * set to not be DMA-capable.
503 * INTR_IO - Indicates that all interrupts are combined to
504 * generate one interrupt. If not set, interrupts
505 * are individual (more virtualization stuff?)
507 * HCCNT_RO - Indicates that the clock timing registers are
508 * RW. If not set, the registers are RO.
509 * (more virtualization stuff).
511 * MAXSPEED - Indicates the maximum speed supported.
513 * DATAW - Indicates the internal bus width in bits.
515 #define IG4_PARAM1_TXFIFO_DEPTH(v) (((v) >> 16) & 0xFF)
516 #define IG4_PARAM1_RXFIFO_DEPTH(v) (((v) >> 8) & 0xFF)
517 #define IG4_PARAM1_CONFIG_VALID 0x00000080
518 #define IG4_PARAM1_CONFIG_HASDMA 0x00000040
519 #define IG4_PARAM1_CONFIG_INTR_IO 0x00000020
520 #define IG4_PARAM1_CONFIG_HCCNT_RO 0x00000010
521 #define IG4_PARAM1_CONFIG_MAXSPEED_MASK 0x0000000C
522 #define IG4_PARAM1_CONFIG_DATAW_MASK 0x00000003
524 #define IG4_CONFIG_MAXSPEED_RESERVED00 0x00000000
525 #define IG4_CONFIG_MAXSPEED_STANDARD 0x00000004
526 #define IG4_CONFIG_MAXSPEED_FAST 0x00000008
527 #define IG4_CONFIG_MAXSPEED_HIGH 0x0000000C
529 #define IG4_CONFIG_DATAW_8 0x00000000
530 #define IG4_CONFIG_DATAW_16 0x00000001
531 #define IG4_CONFIG_DATAW_32 0x00000002
532 #define IG4_CONFIG_DATAW_RESERVED11 0x00000003
535 * COMP_VER - (RO) Component Version Register 22.2.36
536 * Default Value 0x3131352A
538 * Contains the chip version number. All 32 bits.
540 #define IG4_COMP_VER 0x3131352A
543 * COMP_TYPE - (RO) (linux) Endian and bus width probe
545 * Read32 from this register and test against IG4_COMP_TYPE
546 * to determine the bus width. e.g. 01404457 = endian-reversed,
547 * and 00000140 or 00004457 means internal 16-bit bus (?).
549 * This register is not in the intel documentation, I pulled it
550 * from the linux driver i2c-designware-core.c.
552 #define IG4_COMP_TYPE 0x44570140
555 * RESETS - (RW) Resets Register 22.2.37
557 * Used to reset the I2C host controller by SW. There is no timing
558 * requirement, software can assert and de-assert in back-to-back
561 * 00 I2C host controller is NOT in reset.
564 * 11 I2C host controller is in reset.
566 #define IG4_RESETS_ASSERT 0x0003
567 #define IG4_RESETS_DEASSERT 0x0000
570 * GENERAL - (RW) General Reigster 22.2.38
572 * IOVOLT 0=1.8V 1=3.3V
576 * In Auto mode the BIOS will write to the host controller's
577 * AUTO LTR Value register (offset 0x0814) with the active
578 * state LTR value, and will write to the SW LTR Value register
579 * (offset 0x0810) with the idle state LTR value.
581 * In SW mode the SW will write to the host controller SW LTR
582 * value (offset 0x0810). It is the SW responsibility to update
583 * the LTR with the appropriate value.
585 #define IG4_GENERAL_IOVOLT3_3 0x0008
586 #define IG4_GENERAL_SWMODE 0x0004
589 * SW_LTR_VALUE - (RW) SW LTR Value Register 22.2.39
590 * AUTO_LTR_VALUE - (RW) SW LTR Value Register 22.2.40
592 * Default value is 0x00000800 which means the best possible
593 * service/response time.
595 * It isn't quite clear how the snooping works. There are two scale
596 * bits for both sets but two of the four codes are reserved. The
597 * *SNOOP_VALUE() is specified as a 10-bit latency value. If 0, it
598 * indicates that the device cannot tolerate any delay and needs the
599 * best possible service/response time.
601 * I think this is for snooping (testing) the I2C bus. The lowest
602 * delay (0) probably runs the controller polling at a high, power hungry
605 #define IG4_SWLTR_NSNOOP_REQ 0x80000000 /* (ro) */
606 #define IG4_SWLTR_NSNOOP_SCALE_MASK 0x1C000000 /* (ro) */
607 #define IG4_SWLTR_NSNOOP_SCALE_1US 0x08000000 /* (ro) */
608 #define IG4_SWLTR_NSNOOP_SCALE_32US 0x0C000000 /* (ro) */
609 #define IG4_SWLTR_NSNOOP_VALUE_DECODE(v) (((v) >> 16) & 0x3F)
610 #define IG4_SWLTR_NSNOOP_VALUE_ENCODE(v) (((v) & 0x3F) << 16)
612 #define IG4_SWLTR_SNOOP_REQ 0x00008000 /* (rw) */
613 #define IG4_SWLTR_SNOOP_SCALE_MASK 0x00001C00 /* (rw) */
614 #define IG4_SWLTR_SNOOP_SCALE_1US 0x00000800 /* (rw) */
615 #define IG4_SWLTR_SNOOP_SCALE_32US 0x00000C00 /* (rw) */
616 #define IG4_SWLTR_SNOOP_VALUE_DECODE(v) ((v) & 0x3F)
617 #define IG4_SWLTR_SNOOP_VALUE_ENCODE(v) ((v) & 0x3F)