2 # LINT -- config file for checking all the sources, tries to pull in
3 # as much of the source tree as it can.
5 # $FreeBSD: src/sys/i386/conf/LINT,v 1.749.2.144 2003/06/04 17:56:59 sam Exp $
6 # $DragonFly: src/sys/i386/conf/Attic/LINT,v 1.39 2004/09/26 01:52:48 dillon Exp $
8 # NB: You probably don't want to try running a kernel built from this
9 # file. Instead, you should start from GENERIC, and add options from
10 # this file as required.
14 # This directive is mandatory; it defines the architecture to be
15 # configured for; in this case, the 386 family based IBM-PC and
21 # This is the ``identification'' of the kernel. Usually this should
22 # be the same as the name of your kernel.
27 # The `maxusers' parameter controls the static sizing of a number of
28 # internal system tables by a formula defined in subr_param.c. Setting
29 # maxusers to 0 will cause the system to auto-size based on physical
35 # The `makeoptions' parameter allows variables to be passed to the
36 # generated Makefile in the build area.
38 # CONF_CFLAGS gives some extra compiler flags that are added to ${CFLAGS}
39 # after most other flags. Here we use it to inhibit use of non-optimal
40 # gcc builtin functions (e.g., memcmp).
42 # DEBUG happens to be magic.
43 # The following is equivalent to 'config -g KERNELNAME' and creates
44 # 'kernel.debug' compiled with -g debugging as well as a normal
45 # 'kernel'. Use 'make install.debug' to install the debug kernel
46 # but that isn't normally necessary as the debug symbols are not loaded
47 # by the kernel and are not useful there anyway.
49 # KERNEL can be overridden so that you can change the default name of your
52 # MODULES_OVERRIDE can be used to limit modules built to a specific list.
54 makeoptions CONF_CFLAGS=-fno-builtin #Don't allow use of memcmp, etc.
55 #makeoptions DEBUG=-g #Build kernel with gdb(1) debug symbols
56 #makeoptions KERNEL=foo #Build kernel "foo" and install "/foo"
57 # Only build Linux API modules and plus those parts of the sound system I need.
58 #makeoptions MODULES_OVERRIDE="linux sound/snd sound/pcm sound/driver/maestro3"
61 # Certain applications can grow to be larger than the 128M limit
62 # that FreeBSD initially imposes. Below are some options to
63 # allow that limit to grow to 256MB, and can be increased further
64 # with changing the parameters. MAXDSIZ is the maximum that the
65 # limit can be set to, and the DFLDSIZ is the default value for
66 # the limit. MAXSSIZ is the maximum that the stack limit can be
67 # set to. You might want to set the default lower than the max,
68 # and explicitly set the maximum with a shell command for processes
69 # that regularly exceed the limit like INND.
71 options MAXDSIZ="(256*1024*1024)"
72 options MAXSSIZ="(256*1024*1024)"
73 options DFLDSIZ="(256*1024*1024)"
76 # BLKDEV_IOSIZE sets the default block size used in user block
77 # device I/O. Note that this value will be overriden by the label
78 # when specifying a block device from a label with a non-0
79 # partition blocksize. The default is PAGE_SIZE.
81 options BLKDEV_IOSIZE=8192
83 # Options for the VM subsystem.
84 options PQ_CACHESIZE=512 # color for 512k/16k cache
86 # This allows you to actually store this configuration file into
87 # the kernel binary itself, where it may be later read by saying:
88 # strings -n 3 /kernel | sed -n 's/^___//p' > MYKERNEL
90 options INCLUDE_CONFIG_FILE # Include this file in kernel
93 # The root device and filesystem type can be compiled in;
94 # this provides a fallback option if the root device cannot
95 # be correctly guessed by the bootstrap code, or an override if
96 # the RB_DFLTROOT flag (-r) is specified when booting the kernel.
98 options ROOTDEVNAME=\"ufs:da0s2e\"
101 #####################################################################
104 # SMP enables building of a Symmetric MultiProcessor Kernel.
105 # APIC_IO enables the use of the IO APIC for Symmetric I/O.
109 # An SMP kernel will ONLY run on an Intel MP spec. qualified motherboard.
111 # Be sure to disable 'cpu I386_CPU' && 'cpu I486_CPU' for SMP kernels.
113 # Check the 'Rogue SMP hardware' section to see if additional options
114 # are required by your hardware.
118 options SMP # Symmetric MultiProcessor Kernel
119 options APIC_IO # Symmetric (APIC) I/O
122 # Rogue SMP hardware:
127 # The MP tables of most of the current generation MP motherboards
128 # do NOT properly support bridged PCI cards. To use one of these
129 # cards you should refer to ???
132 #####################################################################
136 # You must specify at least one CPU (the one you intend to run on);
137 # deleting the specification for CPUs you don't need to use may make
138 # parts of the system run faster. This is especially true removing
143 cpu I586_CPU # aka Pentium(tm)
144 cpu I686_CPU # aka Pentium Pro(tm)
147 # Options for CPU features.
149 # CPU_ATHLON_SSE_HACK tries to enable SSE instructions when the BIOS has
150 # forgotten to enable them.
152 # CPU_BLUELIGHTNING_FPU_OP_CACHE enables FPU operand cache on IBM
153 # BlueLightning CPU. It works only with Cyrix FPU, and this option
154 # should not be used with Intel FPU.
156 # CPU_BLUELIGHTNING_3X enables triple-clock mode on IBM Blue Lightning
157 # CPU if CPU supports it. The default is double-clock mode on
158 # BlueLightning CPU box.
160 # CPU_BTB_EN enables branch target buffer on Cyrix 5x86 (NOTE 1).
162 # CPU_DIRECT_MAPPED_CACHE sets L1 cache of Cyrix 486DLC CPU in direct
163 # mapped mode. Default is 2-way set associative mode.
165 # CPU_CYRIX_NO_LOCK enables weak locking for the entire address space
166 # of Cyrix 6x86 and 6x86MX CPUs by setting the NO_LOCK bit of CCR1.
167 # Otherwise, the NO_LOCK bit of CCR1 is cleared. (NOTE 3)
169 # CPU_DISABLE_5X86_LSSER disables load store serialize (i.e. enables
170 # reorder). This option should not be used if you use memory mapped
173 # CPU_DISABLE_SSE disables SSE/MMX2 instructions support.
175 # CPU_ENABLE_TCC enables Thermal Control Circuitry (TCC) found in some
176 # Pentium(tm) 4 and (possibly) later CPUs. When enabled and detected,
177 # TCC supports restricting power consumption using the hw.p4tcc.*
178 # sysctls. This operates independently of SpeedStep and is useful on
179 # systems where other mechanisms such as apm(4) or acpi(4) don't work.
181 # CPU_FASTER_5X86_FPU enables faster FPU exception handler.
183 # CPU_I486_ON_386 enables CPU cache on i486 based CPU upgrade products
186 # CPU_IORT defines I/O clock delay time (NOTE 1). Default values of
187 # I/O clock delay time on Cyrix 5x86 and 6x86 are 0 and 7,respectively
190 # CPU_L2_LATENCY specifed the L2 cache latency value. This option is used
191 # only when CPU_PPRO2CELERON is defined and Mendocino Celeron is detected.
192 # The default value is 5.
194 # CPU_ELAN enables support for AMDs ElanSC520 CPU.
196 # CPU_LOOP_EN prevents flushing the prefetch buffer if the destination
197 # of a jump is already present in the prefetch buffer on Cyrix 5x86(NOTE
200 # CPU_PPRO2CELERON enables L2 cache of Mendocino Celeron CPUs. This option
201 # is useful when you use Socket 8 to Socket 370 converter, because most Pentium
202 # Pro BIOSs do not enable L2 cache of Mendocino Celeron CPUs.
204 # CPU_RSTK_EN enables return stack on Cyrix 5x86 (NOTE 1).
206 # CPU_SUSP_HLT enables suspend on HALT. If this option is set, CPU
207 # enters suspend mode following execution of HALT instruction.
209 # CPU_WT_ALLOC enables write allocation on Cyrix 6x86/6x86MX and AMD
212 # CYRIX_CACHE_WORKS enables CPU cache on Cyrix 486 CPUs with cache
213 # flush at hold state.
215 # CYRIX_CACHE_REALLY_WORKS enables (1) CPU cache on Cyrix 486 CPUs
216 # without cache flush at hold state, and (2) write-back CPU cache on
217 # Cyrix 6x86 whose revision < 2.7 (NOTE 2).
219 # NO_F00F_HACK disables the hack that prevents Pentiums (and ONLY
220 # Pentiums) from locking up when a LOCK CMPXCHG8B instruction is
221 # executed. This option is only needed if I586_CPU is also defined,
222 # and should be included for any non-Pentium CPU that defines it.
224 # NO_MEMORY_HOLE is an optimisation for systems with AMD K6 processors
225 # which indicates that the 15-16MB range is *definitely* not being
226 # occupied by an ISA memory hole.
228 # NOTE 1: The options, CPU_BTB_EN, CPU_LOOP_EN, CPU_IORT,
229 # CPU_LOOP_EN and CPU_RSTK_EN should not be used because of CPU bugs.
230 # These options may crash your system.
232 # NOTE 2: If CYRIX_CACHE_REALLY_WORKS is not set, CPU cache is enabled
233 # in write-through mode when revision < 2.7. If revision of Cyrix
234 # 6x86 >= 2.7, CPU cache is always enabled in write-back mode.
236 # NOTE 3: This option may cause failures for software that requires
237 # locked cycles in order to operate correctly.
239 options CPU_ATHLON_SSE_HACK
240 options CPU_BLUELIGHTNING_FPU_OP_CACHE
241 options CPU_BLUELIGHTNING_3X
243 options CPU_DIRECT_MAPPED_CACHE
244 options CPU_DISABLE_5X86_LSSER
246 options CPU_ENABLE_TCC
247 options CPU_DISABLE_SSE
248 options CPU_FASTER_5X86_FPU
249 options CPU_I486_ON_386
251 options CPU_L2_LATENCY=5
253 options CPU_PPRO2CELERON
257 options CYRIX_CACHE_WORKS
258 options CYRIX_CACHE_REALLY_WORKS
259 #options NO_F00F_HACK
262 # A math emulator is mandatory if you wish to run on hardware which
263 # does not have a floating-point processor. Pick either the original,
264 # bogus (but freely-distributable) math emulator, or a much more
265 # fully-featured but GPL-licensed emulator taken from Linux.
267 options MATH_EMULATE #Support for x87 emulation
268 # Don't enable both of these in a real config.
269 options GPL_MATH_EMULATE #Support for x87 emulation via
273 #####################################################################
274 # COMPATIBILITY OPTIONS
277 # Implement system calls compatible with 4.3BSD and older versions of
278 # FreeBSD. You probably do NOT want to remove this as much current code
279 # still relies on the 4.3 emulation.
284 # These three options provide support for System V Interface
285 # Definition-style interprocess communication, in the form of shared
286 # memory, semaphores, and message queues, respectively.
288 # System V shared memory and tunable parameters
289 options SYSVSHM # include support for shared memory
290 options SHMMAXPGS=1025 # max amount of shared memory pages (4k on i386)
291 options SHMALL=1025 # max amount of shared memory (bytes)
292 options SHMMAX="(SHMMAXPGS*PAGE_SIZE+1)"
293 # max shared memory segment size (bytes)
294 options SHMMIN=2 # min shared memory segment size (bytes)
295 options SHMMNI=33 # max number of shared memory identifiers
296 options SHMSEG=9 # max shared memory segments per process
298 # System V semaphores and tunable parameters
299 options SYSVSEM # include support for semaphores
300 options SEMMAP=31 # amount of entries in semaphore map
301 options SEMMNI=11 # number of semaphore identifiers in the system
302 options SEMMNS=61 # number of semaphores in the system
303 options SEMMNU=31 # number of undo structures in the system
304 options SEMMSL=61 # max number of semaphores per id
305 options SEMOPM=101 # max number of operations per semop call
306 options SEMUME=11 # max number of undo entries per process
308 # System V message queues and tunable parameters
309 options SYSVMSG # include support for message queues
310 options MSGMNB=2049 # max characters per message queue
311 options MSGMNI=41 # max number of message queue identifiers
312 options MSGSEG=2049 # max number of message segments in the system
313 options MSGSSZ=16 # size of a message segment MUST be power of 2
314 options MSGTQL=41 # max amount of messages in the system
317 #####################################################################
321 # Enable the kernel debugger.
326 # Don't drop into DDB for a panic. Intended for unattended operation
327 # where you may want to drop to DDB from the console, but still want
328 # the machine to recover from a panic
330 options DDB_UNATTENDED
333 # If using GDB remote mode to debug the kernel, there's a non-standard
334 # extension to the remote protocol that can be used to use the serial
335 # port as both the debugging port and the system console. It's non-
336 # standard and you're on your own if you enable it. See also the
337 # "remotechat" variables in the FreeBSD specific version of gdb.
339 options GDB_REMOTE_CHAT
342 # KTRACE enables the system-call tracing facility ktrace(2).
344 options KTRACE #kernel tracing
347 # The INVARIANTS option is used in a number of source files to enable
348 # extra sanity checking of internal structures. This support is not
349 # enabled by default because of the extra time it would take to check
350 # for these conditions, which can only occur as a result of
351 # programming errors.
356 # The INVARIANT_SUPPORT option makes us compile in support for
357 # verifying some of the internal structures. It is a prerequisite for
358 # 'INVARIANTS', as enabling 'INVARIANTS' will make these functions be
359 # called. The intent is that you can set 'INVARIANTS' for single
360 # source files (by changing the source file or specifying it on the
361 # command line) if you have 'INVARIANT_SUPPORT' enabled.
363 options INVARIANT_SUPPORT
366 # The DIAGNOSTIC option is used to enable extra debugging information
367 # from some parts of the kernel. As this makes everything more noisy,
368 # it is disabled by default.
373 # PERFMON causes the driver for Pentium/Pentium Pro performance counters
374 # to be compiled. See perfmon(4) for more information.
380 # This option let some drivers co-exist that can't co-exist in a running
381 # system. This is used to be able to compile all kernel code in one go for
382 # quality assurance purposes (like this file, which the option takes it name
385 options COMPILING_LINT
388 # XXX - this doesn't belong here.
389 # Allow ordinary users to take the console - this is useful for X.
392 # XXX - this doesn't belong here either
393 options USERCONFIG #boot -c editor
394 options INTRO_USERCONFIG #imply -c and show intro screen
395 options VISUAL_USERCONFIG #visual boot -c editor
398 #####################################################################
403 # Only the INET (Internet) family is officially supported in FreeBSD.
404 # Source code for the NS (Xerox Network Service) is provided for amusement
407 options INET #Internet communications protocols
408 options INET6 #IPv6 communications protocols
409 options IPSEC #IP security
410 options IPSEC_ESP #IP security (crypto; define w/ IPSEC)
411 options IPSEC_DEBUG #debug for IP security
413 # Set IPSEC_FILTERGIF to force packets coming through a gif tunnel
414 # to be processed by any configured packet filtering (ipfw, ipf).
415 # The default is that packets coming from a tunnel are _not_ processed;
416 # they are assumed trusted.
418 # Note that enabling this can be problematic as there are no mechanisms
419 # in place for distinguishing packets coming out of a tunnel (e.g. no
420 # encX devices as found on openbsd).
422 #options IPSEC_FILTERGIF #filter ipsec packets from a tunnel
425 # Experimental IPsec implementation that uses the kernel crypto
426 # framework. This cannot be configured together with IPSEC and
427 # (currently) supports only IPv4. To use this you must also
428 # configure the crypto device (see below). Note that with this
429 # you get all the IPsec protocols (e.g. there is no FAST_IPSEC_ESP).
430 # IPSEC_DEBUG is used, as above, to configure debugging support
431 # within the IPsec protocols.
433 #options FAST_IPSEC #new IPsec
435 options IPX #IPX/SPX communications protocols
436 options IPXIP #IPX in IP encapsulation (not available)
437 options IPTUNNEL #IP in IPX encapsulation (not available)
439 options NCP #NetWare Core protocol
441 options NETATALK #Appletalk communications protocols
443 # These are currently broken but are shipped due to interest.
444 #options NS #Xerox NS protocols
445 #options NSIP #XNS over IP
449 # NETSMB enables support for SMB protocol, it requires LIBMCHAIN and LIBICONV
451 # NETSMBCRYPTO enables support for encrypted passwords.
452 options NETSMB #SMB/CIFS requester
453 options NETSMBCRYPTO #encrypted password support for SMB
455 # mchain library. It can be either loaded as KLD or compiled into kernel
456 options LIBMCHAIN #mbuf management library
458 # netgraph(4). Enable the base netgraph code with the NETGRAPH option.
459 # Individual node types can be enabled with the corresponding option
460 # listed below; however, this is not strictly necessary as netgraph
461 # will automatically load the corresponding KLD module if the node type
462 # is not already compiled into the kernel. Each type below has a
463 # corresponding man page, e.g., ng_async(8).
464 options NETGRAPH #netgraph(4) system
465 options NETGRAPH_ASYNC
467 options NETGRAPH_CISCO
468 options NETGRAPH_ECHO
469 options NETGRAPH_ETHER
470 options NETGRAPH_FRAME_RELAY
471 options NETGRAPH_HOLE
472 options NETGRAPH_IFACE
473 options NETGRAPH_KSOCKET
474 options NETGRAPH_L2TP
476 # MPPC compression requires proprietary files (not included)
477 #options NETGRAPH_MPPC_COMPRESSION
478 options NETGRAPH_MPPC_ENCRYPTION
479 options NETGRAPH_ONE2MANY
481 options NETGRAPH_PPPOE
482 options NETGRAPH_PPTPGRE
483 options NETGRAPH_RFC1490
484 options NETGRAPH_SOCKET
490 device mn # Munich32x/Falc54 Nx64kbit/sec cards.
493 # Network interfaces:
494 # The `loop' pseudo-device is MANDATORY when networking is enabled.
495 # The `ether' pseudo-device provides generic code to handle
496 # Ethernets; it is MANDATORY when a Ethernet device driver is
497 # configured or token-ring is enabled.
498 # The 'fddi' pseudo-device provides generic code to support FDDI.
499 # The `arcnet' pseudo-device provides generic code to support Arcnet.
500 # The `sppp' pseudo-device serves a similar role for certain types
501 # of synchronous PPP links (like `cx', `ar').
502 # The `sl' pseudo-device implements the Serial Line IP (SLIP) service.
503 # The `ppp' pseudo-device implements the Point-to-Point Protocol.
504 # The `bpf' pseudo-device enables the Berkeley Packet Filter. Be
505 # aware of the legal and administrative consequences of enabling this
506 # option. The number of devices determines the maximum number of
507 # simultaneous BPF clients programs runnable.
508 # The `disc' pseudo-device implements a minimal network interface,
509 # which throws away all packets sent and never receives any. It is
510 # included for testing purposes. This shows up as the 'ds' interface.
511 # The `tun' pseudo-device implements (user-)ppp and nos-tun
512 # The `gif' pseudo-device implements IPv6 over IP4 tunneling,
513 # IPv4 over IPv6 tunneling, IPv4 over IPv4 tunneling and
514 # IPv6 over IPv6 tunneling.
515 # The `gre' device implements two types of IP4 over IP4 tunneling:
516 # GRE and MOBILE, as specified in the RFC1701 and RFC2004.
517 # The `faith' pseudo-device captures packets sent to it and diverts them
518 # to the IPv4/IPv6 translation daemon.
519 # The `stf' device implements 6to4 encapsulation.
520 # The `ef' pseudo-device provides support for multiple ethernet frame types
521 # specified via ETHER_* options. See ef(4) for details.
523 # The PPP_BSDCOMP option enables support for compress(1) style entire
524 # packet compression, the PPP_DEFLATE is for zlib/gzip style compression.
525 # PPP_FILTER enables code for filtering the ppp data stream and selecting
526 # events for resetting the demand dial activity timer - requires bpf.
527 # See pppd(8) for more details.
529 pseudo-device ether #Generic Ethernet
530 pseudo-device vlan 1 #VLAN support
531 pseudo-device token #Generic TokenRing
532 pseudo-device fddi #Generic FDDI
533 pseudo-device arcnet #Generic Arcnet
534 pseudo-device sppp #Generic Synchronous PPP
535 pseudo-device loop #Network loopback device
536 pseudo-device bpf #Berkeley packet filter
537 pseudo-device disc #Discard device (ds0, ds1, etc)
538 pseudo-device tun #Tunnel driver (ppp(8), nos-tun(8))
539 pseudo-device sl 2 #Serial Line IP
540 pseudo-device gre #IP over IP tunneling
541 pseudo-device ppp 2 #Point-to-point protocol
542 options PPP_BSDCOMP #PPP BSD-compress support
543 options PPP_DEFLATE #PPP zlib/deflate/gzip support
544 options PPP_FILTER #enable bpf filtering (needs bpf)
546 pseudo-device ef # Multiple ethernet frames support
547 options ETHER_II # enable Ethernet_II frame
548 options ETHER_8023 # enable Ethernet_802.3 (Novell) frame
549 options ETHER_8022 # enable Ethernet_802.2 frame
550 options ETHER_SNAP # enable Ethernet_802.2/SNAP frame
553 pseudo-device gif #IPv6 and IPv4 tunneling
554 pseudo-device faith 1 #for IPv6 and IPv4 translation
555 pseudo-device stf #6to4 IPv6 over IPv4 encapsulation
558 # Internet family options:
560 # MROUTING enables the kernel multicast packet forwarder, which works
563 # PIM enables Protocol Independent Multicast in the kernel.
564 # Requires MROUTING enabled.
566 # IPFIREWALL enables support for IP firewall construction, in
567 # conjunction with the `ipfw' program. IPFIREWALL_VERBOSE sends
568 # logged packets to the system logger. IPFIREWALL_VERBOSE_LIMIT
569 # limits the number of times a matching entry can be logged.
571 # WARNING: IPFIREWALL defaults to a policy of "deny ip from any to any"
572 # and if you do not add other rules during startup to allow access,
573 # YOU WILL LOCK YOURSELF OUT. It is suggested that you set firewall_type=open
574 # in /etc/rc.conf when first enabling this feature, then refining the
575 # firewall rules in /etc/rc.firewall after you've tested that the new kernel
576 # feature works properly.
578 # IPFIREWALL_DEFAULT_TO_ACCEPT causes the default rule (at boot) to
579 # allow everything. Use with care, if a cracker can crash your
580 # firewall machine, they can get to your protected machines. However,
581 # if you are using it as an as-needed filter for specific problems as
582 # they arise, then this may be for you. Changing the default to 'allow'
583 # means that you won't get stuck if the kernel and /sbin/ipfw binary get
586 # IPDIVERT enables the divert IP sockets, used by ``ipfw divert''
588 # IPSTEALTH enables code to support stealth forwarding (i.e., forwarding
589 # packets without touching the ttl). This can be useful to hide firewalls
590 # from traceroute and similar tools.
592 # TCPDEBUG is undocumented.
594 options MROUTING # Multicast routing
595 options PIM # Protocol Independent Multicast
596 options IPFIREWALL #firewall
597 options IPFIREWALL_VERBOSE #enable logging to syslogd(8)
598 options IPFIREWALL_FORWARD #enable transparent proxy support
599 options IPFIREWALL_VERBOSE_LIMIT=100 #limit verbosity
600 options IPFIREWALL_DEFAULT_TO_ACCEPT #allow everything by default
601 options IPV6FIREWALL #firewall for IPv6
602 options IPV6FIREWALL_VERBOSE
603 options IPV6FIREWALL_VERBOSE_LIMIT=100
604 options IPV6FIREWALL_DEFAULT_TO_ACCEPT
605 options IPDIVERT #divert sockets
606 options IPFILTER #ipfilter support
607 options IPFILTER_LOG #ipfilter logging
608 options IPFILTER_DEFAULT_BLOCK #block all packets by default
609 options IPSTEALTH #support for stealth forwarding
611 options NS # NETNS support
617 # The MBUF_STRESS_TEST option enables options which create
618 # various random failures / extreme cases related to mbuf
619 # functions. See the mbuf(9) manpage for a list of available
621 options MBUF_STRESS_TEST
623 # RANDOM_IP_ID causes the ID field in IP packets to be randomized
624 # instead of incremented by 1 with each packet generated. This
625 # option closes a minor information leak which allows remote
626 # observers to determine the rate of packet generation on the
627 # machine by watching the counter.
630 # Statically link in accept filters
631 options ACCEPT_FILTER_DATA
632 options ACCEPT_FILTER_HTTP
635 # TCP_DROP_SYNFIN adds support for ignoring TCP packets with SYN+FIN. This
636 # prevents nmap et al. from identifying the TCP/IP stack, but breaks support
637 # for RFC1644 extensions and is not recommended for web servers.
639 options TCP_DROP_SYNFIN #drop TCP packets with SYN+FIN
641 # ICMP_BANDLIM enables icmp error response bandwidth limiting. You
642 # typically want this option as it will help protect the machine from
643 # D.O.S. packet attacks.
647 # DUMMYNET enables the "dummynet" bandwidth limiter. You need
648 # IPFIREWALL as well. See the dummynet(4) and ipfw(8) manpages for more info.
649 # When you run DUMMYNET it is advisable to also have "options HZ=1000"
650 # to achieve a smoother scheduling of the traffic.
652 # BRIDGE enables bridging between ethernet cards -- see bridge(4).
653 # You can use IPFIREWALL and DUMMYNET together with bridging.
659 # ATM (HARP version) options
661 # ATM_CORE includes the base ATM functionality code. This must be included
664 # ATM_IP includes support for running IP over ATM.
666 # At least one (and usually only one) of the following signalling managers
667 # must be included (note that all signalling managers include PVC support):
668 # ATM_SIGPVC includes support for the PVC-only signalling manager `sigpvc'.
669 # ATM_SPANS includes support for the `spans' signalling manager, which runs
670 # the FORE Systems's proprietary SPANS signalling protocol.
671 # ATM_UNI includes support for the `uni30' and `uni31' signalling managers,
672 # which run the ATM Forum UNI 3.x signalling protocols.
674 # The `hea' driver provides support for the Efficient Networks, Inc.
675 # ENI-155p ATM PCI Adapter.
677 # The `hfa' driver provides support for the FORE Systems, Inc.
678 # PCA-200E ATM PCI Adapter.
680 options ATM_CORE #core ATM protocol family
681 options ATM_IP #IP over ATM support
682 options ATM_SIGPVC #SIGPVC signalling manager
683 options ATM_SPANS #SPANS signalling manager
684 options ATM_UNI #UNI signalling manager
685 device hea #Efficient ENI-155p ATM PCI
686 device hfa #FORE PCA-200E ATM PCI
688 # DEVICE_POLLING adds support for mixed interrupt-polling handling
689 # of network device drivers, which has significant benefits in terms
690 # of robustness to overloads and responsivity, as well as permitting
691 # accurate scheduling of the CPU time between kernel network processing
692 # and other activities. The drawback is a moderate (up to 1/HZ seconds)
693 # potential increase in response times.
694 # It is strongly recommended to use HZ=1000 or 2000 with DEVICE_POLLING
695 # to achieve smoother behaviour.
696 # Additionally, you can enable/disable polling at runtime with the
697 # sysctl variable kern.polling.enable (defaults off), and select
698 # the CPU fraction reserved to userland with the sysctl variable
699 # kern.polling.user_frac (default 50, range 0..100).
701 # Only the "dc" "fxp" and "sis" devices support this mode of operation at
702 # the time of this writing.
704 options DEVICE_POLLING
707 #####################################################################
711 # Only the root, /usr, and /tmp filesystems need be statically
712 # compiled; everything else will be automatically loaded at mount
713 # time. (Exception: the UFS family---FFS, and MFS --- cannot
714 # currently be demand-loaded.) Some people still prefer to statically
715 # compile other filesystems as well.
717 # NB: The NULL, PORTAL, UMAP and UNION filesystems are known to be
718 # buggy, and WILL panic your system if you attempt to do anything with
719 # them. They are included here as an incentive for some enterprising
720 # soul to sit down and fix them.
723 # One of these is mandatory:
724 options FFS #Fast filesystem
725 options MFS #Memory File System
726 options NFS #Network File System
728 # The rest are optional:
729 #options NFS_NOSERVER #Disable the NFS-server code.
730 options CD9660 #ISO 9660 filesystem
731 options FDESC #File descriptor filesystem
732 options KERNFS #Kernel filesystem
733 options MSDOSFS #MS DOS File System
734 options NTFS #NT File System
735 options NULLFS #NULL filesystem
736 options NWFS #NetWare filesystem
737 options PORTAL #Portal filesystem
738 options PROCFS #Process filesystem
739 options SMBFS #SMB/CIFS filesystem
740 options UDF #UDF filesystem
741 options UMAPFS #UID map filesystem
742 options UNION #Union filesystem
743 # The xFS_ROOT options REQUIRE the associated ``options xFS''
744 options CD9660_ROOT #CD-ROM usable as root device
745 options FFS_ROOT #FFS usable as root device
746 options NFS_ROOT #NFS usable as root device
748 # Soft updates is technique for improving file system speed and
749 # making abrupt shutdown less risky.
752 # Directory hashing improves the speed of operations on very large
753 # directories at the expense of some memory.
756 # Make space in the kernel for a root filesystem on a md device.
757 # Define to the number of kilobytes to reserve for the filesystem.
758 options MD_ROOT_SIZE=10
760 # Make the md device a potential root device, either with preloaded
761 # images of type mfs_root or md_root.
764 # Specify double the default maximum size for malloc(9)-backed md devices.
765 options MD_NSECT=40000
767 # Allow this many swap-devices.
769 # In order to manage swap, the system must reserve bitmap space that
770 # scales with the largest mounted swap device multiplied by NSWAPDEV,
771 # irregardless of whether other swap devices exist or not. So it
772 # is not a good idea to make this value too large.
775 # Disk quotas are supported when this option is enabled.
776 options QUOTA #enable disk quotas
778 # If you are running a machine just as a fileserver for PC and MAC
779 # users, using SAMBA or Netatalk, you may consider setting this option
780 # and keeping all those users' directories on a filesystem that is
781 # mounted with the suiddir option. This gives new files the same
782 # ownership as the directory (similar to group). It's a security hole
783 # if you let these users run programs, so confine it to file-servers
784 # (but it'll save you lots of headaches in those cases). Root owned
785 # directories are exempt and X bits are cleared. The suid bit must be
786 # set on the directory as well; see chmod(1) PC owners can't see/set
787 # ownerships so they keep getting their toes trodden on. This saves
788 # you all the support calls as the filesystem it's used on will act as
789 # they expect: "It's my dir so it must be my file".
794 options NFS_MINATTRTIMO=3 # VREG attrib cache timeout in sec
795 options NFS_MAXATTRTIMO=60
796 options NFS_MINDIRATTRTIMO=30 # VDIR attrib cache timeout in sec
797 options NFS_MAXDIRATTRTIMO=60
798 options NFS_GATHERDELAY=10 # Default write gather delay (msec)
799 options NFS_UIDHASHSIZ=29 # Tune the size of nfssvc_sock with this
800 options NFS_WDELAYHASHSIZ=16 # and with this
801 options NFS_MUIDHASHSIZ=63 # Tune the size of nfsmount with this
802 options NFS_DEBUG # Enable NFS Debugging
805 options CODA #CODA filesystem.
806 pseudo-device vcoda 4 #coda minicache <-> venus comm.
809 # Add support for the EXT2FS filesystem of Linux fame. Be a bit
810 # careful with this - the ext2fs code has a tendency to lag behind
811 # changes and not be exercised very much, so mounting read/write could
812 # be dangerous (and even mounting read only could result in panics.)
816 # Use real implementations of the aio_* system calls. There are numerous
817 # stability and security issues in the current aio code that make it
818 # unsuitable for inclusion on machines with untrusted local users.
822 #####################################################################
825 # Real time extensions added in the 1993 Posix
826 # P1003_1B: Infrastructure
827 # _KPOSIX_PRIORITY_SCHEDULING: Build in _POSIX_PRIORITY_SCHEDULING
828 # _KPOSIX_VERSION: Version kernel is built for
831 options _KPOSIX_PRIORITY_SCHEDULING
832 options _KPOSIX_VERSION=199309L
835 #####################################################################
838 # The granularity of operation is controlled by the kernel option HZ whose
839 # default value (100) means a granularity of 10ms (1s/HZ).
840 # Some subsystems, such as DUMMYNET or DEVICE_POLLING, might benefit from
841 # a smaller granularity such as 1ms or less.
842 # Consider, however, that reducing the granularity too much might
843 # cause excessive overhead in clock interrupt processing,
844 # potentially causing ticks to be missed and thus actually reducing
845 # the accuracy of operation.
849 # The following options are used for debugging clock behavior only, and
850 # should not be used for production systems.
852 # CLK_CALIBRATION_LOOP will run the clock calibration loop at startup
853 # until the user presses a key.
855 options CLK_CALIBRATION_LOOP
857 # The following two options measure the frequency of the corresponding
858 # clock relative to the RTC (onboard mc146818a).
860 options CLK_USE_I8254_CALIBRATION
861 options CLK_USE_TSC_CALIBRATION
864 #####################################################################
867 # SCSI DEVICE CONFIGURATION
869 # The SCSI subsystem consists of the `base' SCSI code, a number of
870 # high-level SCSI device `type' drivers, and the low-level host-adapter
871 # device drivers. The host adapters are listed in the ISA and PCI
872 # device configuration sections below.
874 # Beginning with FreeBSD 2.0.5 you can wire down your SCSI devices so
875 # that a given bus, target, and LUN always come on line as the same
876 # device unit. In earlier versions the unit numbers were assigned
877 # in the order that the devices were probed on the SCSI bus. This
878 # means that if you removed a disk drive, you may have had to rewrite
879 # your /etc/fstab file, and also that you had to be careful when adding
880 # a new disk as it may have been probed earlier and moved your device
881 # configuration around.
883 # This old behavior is maintained as the default behavior. The unit
884 # assignment begins with the first non-wired down unit for a device
885 # type. For example, if you wire a disk as "da3" then the first
886 # non-wired disk will be assigned da4.
888 # The syntax for wiring down devices is:
890 # device scbus0 at ahc0 # Single bus device
891 # device scbus1 at ahc1 bus 0 # Single bus device
892 # device scbus3 at ahc2 bus 0 # Twin bus device
893 # device scbus2 at ahc2 bus 1 # Twin bus device
894 # device da0 at scbus0 target 0 unit 0
895 # device da1 at scbus3 target 1
896 # device da2 at scbus2 target 3
897 # device sa1 at scbus1 target 6
900 # "units" (SCSI logical unit number) that are not specified are
901 # treated as if specified as LUN 0.
903 # All SCSI devices allocate as many units as are required.
905 # The "unknown" device (uk? in pre-2.0.5) is now part of the base SCSI
906 # configuration and doesn't have to be explicitly configured.
908 device scbus #base SCSI code
909 device ch #SCSI media changers
910 device da #SCSI direct access devices (aka disks)
911 device sa #SCSI tapes
912 device cd #SCSI CD-ROMs
913 device pass #CAM passthrough driver
914 device pt #SCSI processor type
915 device ses #SCSI SES/SAF-TE driver
919 # -- NOTE -- If you specify one of the bus/target/lun options, you must
921 # CAMDEBUG: When defined enables debugging macros
922 # CAM_DEBUG_BUS: Debug the given bus. Use -1 to debug all busses.
923 # CAM_DEBUG_TARGET: Debug the given target. Use -1 to debug all targets.
924 # CAM_DEBUG_LUN: Debug the given lun. Use -1 to debug all luns.
925 # CAM_DEBUG_FLAGS: OR together CAM_DEBUG_INFO, CAM_DEBUG_TRACE,
926 # CAM_DEBUG_SUBTRACE, and CAM_DEBUG_CDB
928 # CAM_MAX_HIGHPOWER: Maximum number of concurrent high power (start unit) cmds
929 # SCSI_NO_SENSE_STRINGS: When defined disables sense descriptions
930 # SCSI_NO_OP_STRINGS: When defined disables opcode descriptions
931 # SCSI_DELAY: The number of MILLISECONDS to freeze the SIM (scsi adapter)
932 # queue after a bus reset, and the number of milliseconds to
933 # freeze the device queue after a bus device reset.
935 options CAM_DEBUG_BUS=-1
936 options CAM_DEBUG_TARGET=-1
937 options CAM_DEBUG_LUN=-1
938 options CAM_DEBUG_FLAGS="CAM_DEBUG_INFO|CAM_DEBUG_TRACE|CAM_DEBUG_CDB"
939 options CAM_MAX_HIGHPOWER=4
940 options SCSI_NO_SENSE_STRINGS
941 options SCSI_NO_OP_STRINGS
942 options SCSI_DELAY=8000 # Be pessimistic about Joe SCSI device
944 # Options for the CAM CDROM driver:
945 # CHANGER_MIN_BUSY_SECONDS: Guaranteed minimum time quantum for a changer LUN
946 # CHANGER_MAX_BUSY_SECONDS: Maximum time quantum per changer LUN, only
947 # enforced if there is I/O waiting for another LUN
948 # The compiled in defaults for these variables are 2 and 10 seconds,
951 # These can also be changed on the fly with the following sysctl variables:
952 # kern.cam.cd.changer.min_busy_seconds
953 # kern.cam.cd.changer.max_busy_seconds
955 options CHANGER_MIN_BUSY_SECONDS=2
956 options CHANGER_MAX_BUSY_SECONDS=10
958 # Options for the CAM sequential access driver:
959 # SA_IO_TIMEOUT: Timeout for read/write/wfm operations, in minutes
960 # SA_SPACE_TIMEOUT: Timeout for space operations, in minutes
961 # SA_REWIND_TIMEOUT: Timeout for rewind operations, in minutes
962 # SA_ERASE_TIMEOUT: Timeout for erase operations, in minutes
963 # SA_1FM_AT_EOD: Default to model which only has a default one filemark at EOT.
964 options SA_IO_TIMEOUT="(4)"
965 options SA_SPACE_TIMEOUT="(60)"
966 options SA_REWIND_TIMEOUT="(2*60)"
967 options SA_ERASE_TIMEOUT="(4*60)"
968 options SA_1FM_AT_EOD
970 # Optional timeout for the CAM processor target (pt) device
971 # This is specified in seconds. The default is 60 seconds.
972 options SCSI_PT_DEFAULT_TIMEOUT="60"
974 # Optional enable of doing SES passthrough on other devices (e.g., disks)
976 # Normally disabled because a lot of newer SCSI disks report themselves
977 # as having SES capabilities, but this can then clot up attempts to build
978 # build a topology with the SES device that's on the box these drives
980 options SES_ENABLE_PASSTHROUGH
983 #####################################################################
984 # MISCELLANEOUS DEVICES AND OPTIONS
986 # The `pty' device usually turns out to be ``effectively mandatory'',
987 # as it is required for `telnetd', `rlogind', `screen', `emacs', and
988 # `xterm', among others.
990 pseudo-device pty #Pseudo ttys
991 pseudo-device speaker #Play IBM BASIC-style noises out your speaker
992 pseudo-device gzip #Exec gzipped a.out's
993 pseudo-device vn #Vnode driver (turns a file into a device)
994 pseudo-device md #Memory/malloc disk
995 pseudo-device snp #Snoop device - to look at pty/vty/etc..
996 pseudo-device ccd 4 #Concatenated disk driver
998 # Configuring Vinum into the kernel is not necessary, since the kld
999 # module gets started automatically when vinum(8) starts. This
1000 # device is also untested. Use at your own risk.
1002 # The option VINUMDEBUG must match the value set in CFLAGS
1003 # in src/sbin/vinum/Makefile. Failure to do so will result in
1004 # the following message from vinum(8):
1006 # Can't get vinum config: Invalid argument
1008 # see vinum(4) for more reasons not to use these options.
1009 pseudo-device vinum #Vinum concat/mirror/raid driver
1010 options VINUMDEBUG #enable Vinum debugging hooks
1012 # Kernel side iconv library
1015 # Size of the kernel message buffer. Should be N * pagesize.
1016 options MSGBUF_SIZE=40960
1019 #####################################################################
1020 # HARDWARE DEVICE CONFIGURATION
1022 # ISA and EISA devices:
1023 # EISA support is available for some device, so they can be auto-probed.
1024 # MicroChannel (MCA) support is available for some devices.
1027 # Mandatory ISA devices: isa, npx
1031 # ISA-PnP BIOS support
1035 # Options for `isa':
1037 # AUTO_EOI_1 enables the `automatic EOI' feature for the master 8259A
1038 # interrupt controller. This saves about 0.7-1.25 usec for each interrupt.
1039 # This option breaks suspend/resume on some portables.
1041 # AUTO_EOI_2 enables the `automatic EOI' feature for the slave 8259A
1042 # interrupt controller. This saves about 0.7-1.25 usec for each interrupt.
1043 # Automatic EOI is documented not to work for for the slave with the
1044 # original i8259A, but it works for some clones and some integrated
1047 # MAXMEM specifies the amount of RAM on the machine; if this is not
1048 # specified, FreeBSD will first read the amount of memory from the CMOS
1049 # RAM, so the amount of memory will initially be limited to 64MB or 16MB
1050 # depending on the BIOS. If the BIOS reports 64MB, a memory probe will
1051 # then attempt to detect the installed amount of RAM. If this probe
1052 # fails to detect >64MB RAM you will have to use the MAXMEM option.
1053 # The amount is in kilobytes, so for a machine with 128MB of RAM, it would
1054 # be 131072 (128 * 1024).
1056 # BROKEN_KEYBOARD_RESET disables the use of the keyboard controller to
1057 # reset the CPU for reboot. This is needed on some systems with broken
1058 # keyboard controllers.
1060 # PAS_JOYSTICK_ENABLE enables the gameport on the ProAudio Spectrum
1062 options COMPAT_OLDISA #FreeBSD 2.2 and 3.x compatibility shims
1065 options MAXMEM="(128*1024)"
1066 #options BROKEN_KEYBOARD_RESET
1067 #options PAS_JOYSTICK_ENABLE
1069 # Enable support for the kernel PLL to use an external PPS signal,
1070 # under supervision of [x]ntpd(8)
1071 # More info in ntpd documentation: http://www.eecis.udel.edu/~ntp
1075 # If you see the "calcru: negative time of %ld usec for pid %d (%s)\n"
1076 # message you probably have some broken sw/hw which disables interrupts
1077 # for too long. You can make the system more resistant to this by
1078 # choosing a high value for NTIMECOUNTER. The default is 5, there
1079 # is no upper limit but more than a couple of hundred are not productive.
1080 # A better strategy may be to sysctl -w kern.timecounter.method=1
1082 options NTIMECOUNTER=20
1084 # The keyboard controller; it controls the keyboard and the PS/2 mouse.
1085 device atkbdc0 at isa? port IO_KBD
1088 device atkbd0 at atkbdc? irq 1
1090 # Options for atkbd:
1091 options ATKBD_DFLT_KEYMAP # specify the built-in keymap
1092 makeoptions ATKBD_DFLT_KEYMAP="jp.106"
1094 # These options are valid for other keyboard drivers as well.
1095 options KBD_DISABLE_KEYMAP_LOAD # refuse to load a keymap
1096 options KBD_INSTALL_CDEV # install a CDEV entry in /dev
1098 # `flags' for atkbd:
1099 # 0x01 Force detection of keyboard, else we always assume a keyboard
1100 # 0x02 Don't reset keyboard, useful for some newer ThinkPads
1101 # 0x03 Force detection and avoid reset, might help with certain
1103 # 0x04 Old-style (XT) keyboard support, useful for older ThinkPads
1106 device psm0 at atkbdc? irq 12
1109 options PSM_HOOKRESUME #hook the system resume event, useful
1111 options PSM_RESETAFTERSUSPEND #reset the device at the resume event
1113 # The video card driver.
1117 # Try the following option if the mouse pointer is not drawn correctly
1118 # or font does not seem to be loaded properly. May cause flicker on
1120 options VGA_ALT_SEQACCESS
1122 # If you can dispense with some vga driver features, you may want to
1123 # use the following options to save some memory.
1124 options VGA_NO_FONT_LOADING # don't save/load font
1125 options VGA_NO_MODE_CHANGE # don't change video modes
1127 # Older video cards may require this option for proper operation.
1128 options VGA_SLOW_IOACCESS # do byte-wide i/o's to TS and GDC regs
1130 # The following option probably won't work with the LCD displays.
1131 options VGA_WIDTH90 # support 90 column modes
1133 # To include support for VESA video modes
1136 # Splash screen at start up! Screen savers require this too.
1137 pseudo-device splash
1139 # The pcvt console driver (vt220 compatible).
1141 options XSERVER # support for running an X server on vt
1142 options FAT_CURSOR # start with block cursor
1143 # This PCVT option is for keyboards such as those used on IBM ThinkPad laptops
1144 options PCVT_SCANSET=2 # IBM keyboards are non-std
1145 # Other PCVT options are documented in pcvt(4).
1146 options PCVT_24LINESDEF
1147 options PCVT_CTRL_ALT_DEL
1148 options PCVT_EMU_MOUSE
1149 options PCVT_FREEBSD=211
1150 options PCVT_META_ESC
1151 options PCVT_NSCREENS=9
1152 options PCVT_PRETTYSCRNS
1153 options PCVT_SCREENSAVER
1154 options PCVT_USEKBDSEC
1155 options PCVT_VT220KEYB
1157 # The syscons console driver (sco color console compatible).
1159 options MAXCONS=16 # number of virtual consoles
1160 options SC_ALT_MOUSE_IMAGE # simplified mouse cursor in text mode
1161 options SC_DFLT_FONT # compile font in
1162 makeoptions SC_DFLT_FONT=cp850
1163 options SC_DISABLE_DDBKEY # disable `debug' key
1164 options SC_DISABLE_REBOOT # disable reboot key sequence
1165 options SC_HISTORY_SIZE=200 # number of history buffer lines
1166 options SC_MOUSE_CHAR=0x3 # char code for text mode mouse cursor
1167 options SC_PIXEL_MODE # add support for the raster text mode
1169 # The following options will let you change the default colors of syscons.
1170 options SC_NORM_ATTR="(FG_GREEN|BG_BLACK)"
1171 options SC_NORM_REV_ATTR="(FG_YELLOW|BG_GREEN)"
1172 options SC_KERNEL_CONS_ATTR="(FG_RED|BG_BLACK)"
1173 options SC_KERNEL_CONS_REV_ATTR="(FG_BLACK|BG_RED)"
1175 # If you have a two button mouse, you may want to add the following option
1176 # to use the right button of the mouse to paste text.
1177 options SC_TWOBUTTON_MOUSE
1179 # You can selectively disable features in syscons.
1180 options SC_NO_CUTPASTE
1181 options SC_NO_FONT_LOADING
1182 options SC_NO_HISTORY
1183 options SC_NO_SYSMOUSE
1186 # The Numeric Processing eXtension driver. In addition to this, you
1187 # may configure a math emulator (see above). If your machine has a
1188 # hardware FPU and the kernel configuration includes the npx device
1189 # *and* a math emulator compiled into the kernel, the hardware FPU
1190 # will be used, unless it is found to be broken or unless "flags" to
1191 # npx0 includes "0x08", which requests preference for the emulator.
1192 device npx0 at nexus? port IO_NPX flags 0x0 irq 13
1196 # 0x01 don't use the npx registers to optimize bcopy.
1197 # 0x02 don't use the npx registers to optimize bzero.
1198 # 0x04 don't use the npx registers to optimize copyin or copyout.
1199 # 0x08 use emulator even if hardware FPU is available.
1200 # The npx registers are normally used to optimize copying and zeroing when
1201 # all of the following conditions are satisfied:
1202 # I586_CPU is an option
1203 # the cpu is an i586 (perhaps not a Pentium)
1204 # the probe for npx0 succeeds
1205 # INT 16 exception handling works.
1206 # Then copying and zeroing using the npx registers is normally 30-100% faster.
1207 # The flags can be used to control cases where it doesn't work or is slower.
1208 # Setting them at boot time using userconfig works right (the optimizations
1209 # are not used until later in the bootstrap when npx0 is attached).
1210 # Flag 0x08 automatically disables the i586 optimized routines.
1214 # Optional ISA and EISA devices:
1218 # SCSI host adapters: `aha', `aic', `bt'
1220 # adv: All Narrow SCSI bus AdvanSys controllers.
1221 # adw: Second Generation AdvanSys controllers including the ADV940UW.
1223 # ahc: Adaptec 274x/284x/294x
1225 # bt: Most Buslogic controllers
1226 # ncv: NCR 53C500 based SCSI host adapters.
1227 # nsp: Workbit Ninja SCSI-3 based PC Card SCSI host adapters.
1228 # stg: TMC 18C30, 18C50 based ISA/PC Card SCSI host adapters.
1230 # Note that the order is important in order for Buslogic cards to be
1234 device bt0 at isa? port IO_BT0
1241 device stg0 at isa? port 0x140 irq 11
1244 # Adaptec FSA RAID controllers, including integrated DELL controller,
1245 # the Dell PERC 2/QC and the HP NetRAID-4M
1248 device aacp # SCSI Passthrough interface (optional, CAM required)
1251 # Compaq Smart RAID, Mylex DAC960 and AMI MegaRAID controllers. Only
1252 # one entry is needed; the code will find and configure all supported
1255 device ida # Compaq Smart RAID
1256 device mlx # Mylex DAC960
1257 device amr # AMI MegaRAID
1262 device twe # 3ware ATA RAID
1263 device twa # 3ware SATA RAID
1266 # Promise Supertrack SX6000
1276 # The 'ATA' driver supports all ATA and ATAPI devices.
1277 # It can reuse the majors of wd.c for booting purposes.
1278 # You only need one "device ata" for it to find all
1279 # PCI ATA/ATAPI devices on modern machines.
1281 device atadisk # ATA disk drives
1282 device atapicd # ATAPI CDROM drives
1283 device atapifd # ATAPI floppy drives
1284 device atapist # ATAPI tape drives
1285 device atapicam # emulate ATAPI devices as SCSI ditto via CAM
1286 # needs CAM to be present (scbus & pass)
1288 #The following options are valid on the ATA driver:
1290 # ATA_STATIC_ID: controller numbering is static (like the old driver)
1291 # else the device numbers are dynamically allocated.
1292 options ATA_STATIC_ID
1295 # For older non-PCI systems, these are the lines to use:
1296 #device ata0 at isa? port IO_WD1 irq 14
1297 #device ata1 at isa? port IO_WD2 irq 15
1300 # Standard floppy disk controllers: `fdc' and `fd'
1302 device fdc0 at isa? port IO_FD1 irq 6 drq 2
1304 # FDC_DEBUG enables floppy debugging. Since the debug output is huge, you
1305 # gotta turn it actually on by setting the variable fd_debug with DDB,
1309 device fd0 at fdc0 drive 0
1310 device fd1 at fdc0 drive 1
1312 # M-systems DiskOnchip products see src/sys/contrib/dev/fla/README
1316 # Other standard PC hardware: `mse', `sio', etc.
1318 # mse: Logitech and ATI InPort bus mouse ports
1319 # sio: serial ports (see sio(4))
1321 device mse0 at isa? port 0x23c irq 5
1323 device sio0 at isa? port IO_COM1 flags 0x10 irq 4
1326 # `flags' for serial drivers that support consoles (only for sio now):
1327 # 0x10 enable console support for this unit. The other console flags
1328 # are ignored unless this is set. Enabling console support does
1329 # not make the unit the preferred console - boot with -h or set
1330 # the 0x20 flag for that. Currently, at most one unit can have
1331 # console support; the first one (in config file order) with
1332 # this flag set is preferred. Setting this flag for sio0 gives
1333 # the old behaviour.
1334 # 0x20 force this unit to be the console (unless there is another
1335 # higher priority console). This replaces the COMCONSOLE option.
1336 # 0x40 reserve this unit for low level console operations. Do not
1337 # access the device in any normal way.
1338 # 0x80 use this port for serial line gdb support in ddb.
1340 # PnP `flags' (set via userconfig using pnp x flags y)
1341 # 0x1 disable probing of this device. Used to prevent your modem
1342 # from being attached as a PnP modem.
1345 # Options for serial drivers that support consoles (only for sio now):
1346 options BREAK_TO_DEBUGGER #a BREAK on a comconsole goes to
1348 options CONSPEED=115200 # speed for serial console
1351 # Solaris implements a new BREAK which is initiated by a character
1352 # sequence CR ~ ^b which is similar to a familiar pattern used on
1353 # Sun servers by the Remote Console.
1354 options ALT_BREAK_TO_DEBUGGER
1357 options COM_ESP #code for Hayes ESP
1358 options COM_MULTIPORT #code for some cards with shared IRQs
1360 # Other flags for sio that aren't documented in the man page.
1361 # 0x20000 enable hardware RTS/CTS and larger FIFOs. Only works for
1362 # ST16650A-compatible UARTs.
1364 # PCI Universal Communications driver
1365 # Supports various single and multi port PCI serial cards. Maybe later
1366 # also the parallel ports on combination serial/parallel cards. New cards
1367 # can be added in src/sys/dev/puc/pucdata.c.
1369 # If the PUC_FASTINTR option is used the driver will try to use fast
1370 # interrupts. The card must then be the only user of that interrupt.
1371 # Interrupts cannot be shared when using PUC_FASTINTR.
1373 options PUC_FASTINTR
1376 # Network interfaces: `cx', `ed', `el', `ep', `ie', `is', `le', `lnc'
1378 # ar: Arnet SYNC/570i hdlc sync 2/4 port V.35/X.21 serial driver (requires sppp)
1379 # cm: Arcnet SMC COM90c26 / SMC COM90c56
1380 # (and SMC COM90c66 in '56 compatibility mode) adapters.
1381 # cs: IBM Etherjet and other Crystal Semi CS89x0-based adapters
1382 # cx: Cronyx/Sigma multiport sync/async (with Cisco or PPP framing)
1383 # ed: Western Digital and SMC 80xx; Novell NE1000 and NE2000; 3Com 3C503
1384 # el: 3Com 3C501 (slow!)
1386 # ex: Intel EtherExpress Pro/10 and other i82595-based adapters
1387 # fe: Fujitsu MB86960A/MB86965A Ethernet
1388 # ie: AT&T StarLAN 10 and EN100; 3Com 3C507; unknown NI5210; Intel EtherExpress
1389 # le: Digital Equipment EtherWorks 2 and EtherWorks 3 (DEPCA, DE100,
1390 # DE101, DE200, DE201, DE202, DE203, DE204, DE205, DE422)
1391 # lnc: Lance/PCnet cards (Isolan, Novell NE2100, NE32-VL, AMD Am7990 & Am79C960)
1392 # rdp: RealTek RTL 8002-based pocket ethernet adapters
1393 # sbni: Granch SBNI12-xx adapters
1394 # sbsh: Granch SBNI16 SHDSL modem PCI adapters
1395 # sr: RISCom/N2 hdlc sync 1/2 port V.35/X.21 serial driver (requires sppp)
1396 # wl: Lucent Wavelan (ISA card only).
1397 # awi: IEEE 802.11b PRISM I cards.
1398 # wi: Lucent WaveLAN/IEEE 802.11 PCMCIA adapters. Note: this supports both
1399 # the PCMCIA and ISA cards: the ISA card is really a PCMCIA to ISA
1400 # bridge with a PCMCIA adapter plugged into it.
1401 # an: Aironet 4500/4800 802.11 wireless adapters. Supports the PCMCIA,
1402 # PCI and ISA varieties.
1403 # xe: Xircom/Intel EtherExpress Pro100/16 PC Card ethernet controller.
1404 # ray: Raytheon Raylink 802.11 wireless NICs, OEM as Webgear Aviator 2.4GHz
1405 # oltr: Olicom ISA token-ring adapters OC-3115, OC-3117, OC-3118 and OC-3133
1406 # (no options needed)
1408 device ar0 at isa? port 0x300 irq 10 iomem 0xd0000
1409 device cm0 at isa? port 0x2e0 irq 9 iomem 0xdc000
1410 device cs0 at isa? port 0x300
1411 device cx0 at isa? port 0x240 irq 15 drq 7
1412 device ed0 at isa? port 0x280 irq 5 iomem 0xd8000
1413 device el0 at isa? port 0x300 irq 9
1416 device fe0 at isa? port 0x300
1417 device ie0 at isa? port 0x300 irq 5 iomem 0xd0000
1418 device ie1 at isa? port 0x360 irq 7 iomem 0xd0000
1419 device le0 at isa? port 0x300 irq 5 iomem 0xd0000
1420 device lnc0 at isa? port 0x280 irq 10 drq 0
1421 device rdp0 at isa? port 0x378 irq 7 flags 2
1422 device sbni0 at isa? port 0x210 irq 5 flags 0xefdead
1423 device sr0 at isa? port 0x300 irq 5 iomem 0xd0000
1424 device sn0 at isa? port 0x300 irq 10
1429 options WLCACHE # enables the signal-strength cache
1430 options WLDEBUG # enables verbose debugging output
1431 device wl0 at isa? port 0x300
1435 device oltr0 at isa?
1438 # ATM related options
1440 # The `en' device provides support for Efficient Networks (ENI)
1441 # ENI-155 PCI midway cards, and the Adaptec 155Mbps PCI ATM cards (ANA-59x0).
1443 # atm pseudo-device provides generic atm functions and is required for
1445 # NATM enables the netnatm protocol family that can be used to
1448 # the current driver supports only PVC operations (no atm-arp, no multicast).
1449 # for more details, please read the original documents at
1450 # http://www.ccrc.wustl.edu/pub/chuck/tech/bsdatm/bsdatm.html
1454 options NATM #native ATM
1457 # Audio drivers: `snd', `sb', `pas', `gus', `pca'
1459 # snd: Voxware sound support code
1460 # sb: SoundBlaster PCM - SoundBlaster, SB Pro, SB16, ProAudioSpectrum
1461 # sbxvi: SoundBlaster 16
1462 # sbmidi: SoundBlaster 16 MIDI interface
1463 # pas: ProAudioSpectrum PCM and MIDI
1464 # gus: Gravis Ultrasound - Ultrasound, Ultrasound 16, Ultrasound MAX
1465 # gusxvi: Gravis Ultrasound 16-bit PCM (do not use)
1466 # mss: Microsoft Sound System
1467 # css: Crystal Sound System (CSS 423x PnP)
1468 # sscape: Ensoniq Soundscape MIDI interface
1469 # sscape_mss: Ensoniq Soundscape PCM (requires sscape)
1470 # opl: Yamaha OPL-2 and OPL-3 FM - SB, SB Pro, SB 16, ProAudioSpectrum
1471 # uart: stand-alone 6850 UART for MIDI
1472 # mpu: Roland MPU-401 stand-alone card
1474 # Note: It has been reported that ISA DMA with the SoundBlaster will
1475 # lock up the machine (PR docs/5358). If this happens to you,
1476 # turning off USWC write posting in your machine's BIOS may fix
1479 # Beware! The addresses specified below are also hard-coded in
1480 # src/sys/i386/isa/sound/sound_config.h. If you change the values here, you
1481 # must also change the values in the include file.
1483 # pcm: PCM audio through various sound cards.
1485 # This has support for a large number of new audio cards, based on
1486 # CS423x, OPTi931, Yamaha OPL-SAx, and also for SB16, GusPnP.
1487 # For more information about this driver and supported cards,
1488 # see the pcm.4 man page.
1490 # The flags of the device tells the device a bit more info about the
1491 # device that normally is obtained through the PnP interface.
1492 # bit 2..0 secondary DMA channel;
1493 # bit 4 set if the board uses two dma channels;
1494 # bit 15..8 board type, overrides autodetection; leave it
1495 # zero if don't know what to put in (and you don't,
1496 # since this is unsupported at the moment...).
1498 # This driver will use the new PnP code if it's available.
1500 # pca: PCM audio through your PC speaker
1502 # If you have a GUS-MAX card and want to use the CS4231 codec on the
1503 # card the drqs for the gus max must be 8 bit (1, 2, or 3).
1505 # If you would like to use the full duplex option on the gus, then define
1506 # flags to be the ``read dma channel''.
1508 # options BROKEN_BUS_CLOCK #PAS-16 isn't working and OPTI chipset
1509 # options SYMPHONY_PAS #PAS-16 isn't working and SYMPHONY chipset
1510 # options EXCLUDE_SBPRO #PAS-16
1511 # options SBC_IRQ=5 #PAS-16. Must match irq on sb0 line.
1512 # PAS16: The order of the pas0/sb0/opl0 is important since the
1513 # sb emulation is enabled in the pas-16 attach.
1515 # To override the GUS defaults use:
1520 # The src/sys/i386/isa/sound/sound.doc has more information.
1522 # Controls all "VOXWARE" driver sound devices. See Luigi's driver
1523 # below for an alternate which may work better for some cards.
1526 #device pas0 at isa? port 0x388 irq 10 drq 6
1527 #device sb0 at isa? port 0x220 irq 5 drq 1
1528 #device sbxvi0 at isa? drq 5
1529 #device sbmidi0 at isa? port 0x330
1530 #device awe0 at isa? port 0x620
1531 #device gus0 at isa? port 0x220 irq 12 drq 1
1532 ##device gus0 at isa? port 0x220 irq 12 drq 1 flags 0x3
1533 #device mss0 at isa? port 0x530 irq 10 drq 1
1534 #device css0 at isa? port 0x534 irq 5 drq 1 flags 0x08
1535 #device sscape0 at isa? port 0x330 irq 9 drq 0
1536 #device trix0 at isa? port 0x330 irq 6 drq 0
1537 #device sscape_mss0 at isa? port 0x534 irq 5 drq 1
1538 #device opl0 at isa? port 0x388
1539 #device mpu0 at isa? port 0x330 irq 6 drq 0
1540 #device uart0 at isa? port 0x330 irq 5
1542 # The newpcm driver (use INSTEAD of snd0 and all VOXWARE drivers!).
1543 # Note that motherboard sound devices may require device PNPBIOS.
1545 # Supported cards include:
1546 # Creative SoundBlaster ISA PnP/non-PnP
1547 # Supports ESS and Avance ISA chips as well.
1548 # Gravis UltraSound ISA PnP/non-PnP
1549 # Crystal Semiconductor CS461x/428x PCI
1550 # Neomagic 256AV (ac97)
1551 # Most of the more common ISA/PnP sb/mss/ess compatible cards.
1553 # For non-pnp sound cards with no bridge drivers only:
1554 device pcm0 at isa? irq 10 drq 1 flags 0x0
1556 # For PnP/PCI sound cards
1559 # The bridge drivers for sound cards. These can be separately configured
1560 # for providing services to the likes of new-midi (not in the tree yet).
1561 # When used with 'device pcm' they also provide pcm sound services.
1563 # sbc: Creative SoundBlaster ISA PnP/non-PnP
1564 # Supports ESS and Avance ISA chips as well.
1565 # gusc: Gravis UltraSound ISA PnP/non-PnP
1566 # csa: Crystal Semiconductor CS461x/428x PCI
1568 # For non-PnP cards:
1569 device sbc0 at isa? port 0x220 irq 5 drq 1 flags 0x15
1570 device gusc0 at isa? port 0x220 irq 5 drq 1 flags 0x13
1572 # Not controlled by `snd'
1573 # XXX-Hiten The pca driver needs to readded back into LINT!
1574 # device pca0 at isa? port IO_TIMER1
1577 # Miscellaneous hardware:
1579 # mcd: Mitsumi CD-ROM using proprietary (non-ATAPI) interface
1580 # scd: Sony CD-ROM using proprietary (non-ATAPI) interface
1581 # wt: Wangtek and Archive QIC-02/QIC-36 tape drives
1582 # ctx: Cortex-I frame grabber
1583 # apm: Laptop Advanced Power Management (experimental)
1584 # spigot: The Creative Labs Video Spigot video-acquisition board
1585 # meteor: Matrox Meteor video capture board
1586 # bktr: Brooktree bt848/848a/849a/878/879 video capture and TV Tuner board
1587 # cy: Cyclades serial driver
1588 # dgb: Digiboard PC/Xi and PC/Xe series driver (ALPHA QUALITY!)
1589 # dgm: Digiboard PC/Xem driver
1590 # gp: National Instruments AT-GPIB and AT-GPIB/TNT board
1591 # asc: GI1904-based hand scanners, e.g. the Trust Amiscan Grey
1592 # gsc: Genius GS-4500 hand scanner.
1594 # labpc: National Instrument's Lab-PC and Lab-PC+
1595 # rc: RISCom/8 multiport card
1596 # rp: Comtrol Rocketport(ISA) - single card
1597 # tw: TW-523 power line interface for use with X-10 home control products
1598 # si: Specialix SI/XIO 4-32 port terminal multiplexor
1599 # spic: Sony Programmable I/O controller (VAIO notebooks)
1600 # stl: Stallion EasyIO and EasyConnection 8/32 (ISA and PCI), EasyConnection 8/64 PCI
1601 # stli: Stallion EasyConnection 8/64 ISA/EISA, ONboard, Brumby (intelligent)
1602 # nmdm: nullmodem terminal driver (see nmdm(4))
1605 # The flags takes the following meaning for apm0:
1606 # 0x0020 Statclock is broken.
1607 # If apm is omitted, some systems require sysctl -w kern.timecounter.method=1
1608 # for correct timekeeping.
1610 # Notes on the spigot:
1611 # The video spigot is at 0xad6. This port address can not be changed.
1612 # The irq values may only be 10, 11, or 15
1613 # I/O memory is an 8kb region. Possible values are:
1614 # 0a0000, 0a2000, ..., 0fffff, f00000, f02000, ..., ffffff
1615 # The start address must be on an even boundary.
1616 # Add the following option if you want to allow non-root users to be able
1617 # to access the spigot. This option is not secure because it allows users
1618 # direct access to the I/O page.
1619 # options SPIGOT_UNSECURE
1621 # Notes on the Comtrol Rocketport driver:
1623 # The exact values used for rp0 depend on how many boards you have
1624 # in the system. The manufacturer's sample configs are listed as:
1626 # Comtrol Rocketport ISA single card
1627 # device rp0 at isa? port 0x280
1629 # If instead you have two ISA cards, one installed at 0x100 and the
1630 # second installed at 0x180, then you should add the following to
1631 # your kernel configuration file:
1633 # device rp0 at isa? port 0x100
1634 # device rp1 at isa? port 0x180
1636 # For 4 ISA cards, it might be something like this:
1638 # device rp0 at isa? port 0x180
1639 # device rp1 at isa? port 0x100
1640 # device rp2 at isa? port 0x340
1641 # device rp3 at isa? port 0x240
1643 # And for PCI cards, you only need say:
1647 # Notes on the Digiboard driver:
1649 # The following flag values have special meanings:
1650 # 0x01 - alternate layout of pins (dgb & dgm)
1651 # 0x02 - use the windowed PC/Xe in 64K mode (dgb only)
1653 # Notes on the Specialix SI/XIO driver:
1654 # **This is NOT a Specialix supported Driver!**
1655 # The host card is memory, not IO mapped.
1656 # The Rev 1 host cards use a 64K chunk, on a 32K boundary.
1657 # The Rev 2 host cards use a 32K chunk, on a 32K boundary.
1658 # The cards can use an IRQ of 11, 12 or 15.
1660 # Notes on the Stallion stl and stli drivers:
1661 # See src/i386/isa/README.stl for complete instructions.
1662 # This is version 2.0.0, unsupported by Stallion.
1663 # The stl driver has a secondary IO port hard coded at 0x280. You need
1664 # to change src/i386/isa/stallion.c if you reconfigure this on the boards.
1665 # The "flags" and "iosiz" settings on the stli driver depend on the board:
1666 # EasyConnection 8/64 ISA: flags 23 iosiz 0x1000
1667 # EasyConnection 8/64 EISA: flags 24 iosiz 0x10000
1668 # EasyConnection 8/64 MCA: flags 25 iosiz 0x1000
1669 # ONboard ISA: flags 4 iosiz 0x10000
1670 # ONboard EISA: flags 7 iosiz 0x10000
1671 # ONboard MCA: flags 3 iosiz 0x10000
1672 # Brumby: flags 2 iosiz 0x4000
1673 # Stallion: flags 1 iosiz 0x10000
1674 # For the PCI cards, "device stl" will suffice.
1676 device mcd0 at isa? port 0x300 irq 10
1677 # for the Sony CDU31/33A CDROM
1678 device scd0 at isa? port 0x230
1679 # for the SoundBlaster 16 multicd - up to 4 devices
1680 device wt0 at isa? port 0x300 irq 5 drq 1
1681 device ctx0 at isa? port 0x230 iomem 0xd0000
1682 device spigot0 at isa? port 0xad6 irq 15 iomem 0xee000
1684 device gp0 at isa? port 0x2c0
1685 device gsc0 at isa? port IO_GSC1 drq 3
1686 device joy0 at isa? port IO_GAME
1687 device cy0 at isa? irq 10 iomem 0xd4000 iosiz 0x2000
1688 options CY_PCI_FASTINTR # Use with cy_pci unless irq is shared
1689 device dgb0 at isa? port 0x220 iomem 0xfc000
1690 options NDGBPORTS=16 # Defaults to 16*NDGB
1691 device dgm0 at isa? port 0x104 iomem 0xd0000
1692 device labpc0 at isa? port 0x260 irq 5
1693 device rc0 at isa? port 0x220 irq 12
1694 device rp0 at isa? port 0x280
1695 # the port and irq for tw0 are fictitious
1696 device tw0 at isa? port 0x380 irq 11
1697 device si0 at isa? iomem 0xd0000 irq 12
1698 device asc0 at isa? port IO_ASC1 drq 3 irq 10
1699 device spic0 at isa? irq 0 port 0x10a0
1700 device stl0 at isa? port 0x2a0 irq 10
1701 device stli0 at isa? port 0x2a0 iomem 0xcc000 flags 23 iosiz 0x1000
1702 # HOT1 Xilinx 6200 card (http://www.vcc.com/)
1704 # nullmodem terminal driver
1710 # The MCA bus device is `mca'. It provides auto-detection and
1711 # configuration support for all devices on the MCA bus.
1713 # The 'aha' device provides support for the Adaptec 1640
1715 # The 'bt' device provides support for various Buslogic/Bustek
1716 # and Storage Dimensions SCSI adapters.
1718 # The 'ep' device provides support for the 3Com 3C529 ethernet card.
1725 # The EISA bus device is `eisa'. It provides auto-detection and
1726 # configuration support for all devices on the EISA bus.
1728 # The `ahb' device provides support for the Adaptec 174X adapter.
1730 # The `ahc' device provides support for the Adaptec 274X and 284X
1731 # adapters. The 284X, although a VLB card, responds to EISA probes.
1733 # fea: DEC DEFEA EISA FDDI adapter
1740 # The aic7xxx driver will attempt to use memory mapped I/O for all PCI
1741 # controllers that have it configured only if this option is set. Unfortunately,
1742 # this doesn't work on some motherboards, which prevents it from being the
1744 options AHC_ALLOW_MEMIO
1746 # The adw driver will attempt to use memory mapped I/O for all PCI
1747 # controllers that have it configured only if this option is set.
1748 options ADW_ALLOW_MEMIO
1750 # By default, only 10 EISA slots are probed, since the slot numbers
1751 # above clash with the configuration address space of the PCI subsystem,
1752 # and the EISA probe is not very smart about this. This is sufficient
1753 # for most machines, but in particular the HP NetServer LC series comes
1754 # with an onboard AIC7770 dual-channel SCSI controller on EISA slot #11,
1755 # thus you need to bump this figure to 12 for them.
1756 options EISA_SLOTS=12
1759 # PCI devices & PCI options:
1761 # The main PCI bus device is `pci'. It provides auto-detection and
1762 # configuration support for all devices on the PCI bus, using either
1763 # configuration mode defined in the PCI specification.
1769 #Enable pci resources left off by a "lazy" BIOS.
1771 #WARNING! PCI_ENABLE_IO_MODES IS A VERY DANGEROUS OPTION AND MANY
1772 #SYSTEMS WILL EXPERIENCE INSTABILITY WITH IT ON. USE ONLY AS A LAST
1775 options PCI_ENABLE_IO_MODES
1776 #options PCI_QUIET #quiets PCI code on chipset settings
1777 options COMPAT_OLDPCI #FreeBSD 2.2 and 3.x compatibility shims
1784 # The `ahc' device provides support for the Adaptec 29/3940(U)(W)
1785 # and motherboard based AIC7870/AIC7880 adapters.
1787 # The 'ahd' device provides support for the Adaptec 79xx Ultra320
1788 # SCSI adapters. Options are documented in the ahd(4) manpage:
1790 options AHD_DEBUG_OPTS=0xffffffff
1791 options AHD_REG_PRETTY_PRINT
1792 #options AHD_TMODE_ENABLE=0xff
1794 # The `amd' device provides support for the AMD 53C974 SCSI host
1795 # adapter chip as found on devices such as the Tekram DC-390(T).
1797 # The `bge' device provides support for gigabit ethernet adapters
1798 # based on the Broadcom BCM570x familiy of controllers, including the
1799 # 3Com 3c996-T, the Netgear GA302T, the SysKonnect SK-9D21 and SK-9D41,
1800 # and the embedded gigE NICs on Dell PowerEdge 2550 servers.
1802 # The `ncr' device provides support for the NCR 53C810 and 53C825
1803 # self-contained SCSI host adapters.
1805 # The `isp' device provides support for the Qlogic ISP 1020, 1040
1806 # nd 1040B PCI SCSI host adapters, ISP 1240 Dual Ultra SCSI,
1807 # ISP 1080 and 1280 (Dual) Ultra2, ISP 12160 Ultra3 SCSI, as well as
1808 # the Qlogic ISP 2100 and ISP 2200 Fibre Channel Host Adapters.
1810 # The `dc' device provides support for PCI fast ethernet adapters
1811 # based on the DEC/Intel 21143 and various workalikes including:
1812 # the ADMtek AL981 Comet and AN985 Centaur, the ASIX Electronics
1813 # AX88140A and AX88141, the Davicom DM9100 and DM9102, the Lite-On
1814 # 82c168 and 82c169 PNIC, the Lite-On/Macronix LC82C115 PNIC II
1815 # and the Macronix 98713/98713A/98715/98715A/98725 PMAC. This driver
1816 # replaces the old al, ax, dm, pn and mx drivers. List of brands:
1817 # Digital DE500-BA, Kingston KNE100TX, D-Link DFE-570TX, SOHOware SFA110,
1818 # SVEC PN102-TX, CNet Pro110B, 120A, and 120B, Compex RL100-TX,
1819 # LinkSys LNE100TX, LNE100TX V2.0, Jaton XpressNet, Alfa Inc GFC2204,
1822 # The `de' device provides support for the Digital Equipment DC21040
1823 # self-contained Ethernet adapter.
1825 # The `em' device provides support for the Intel Pro/1000 Family of Gigabit
1826 # adapters (82542, 82543, 82544, 82540).
1828 # The `fxp' device provides support for the Intel EtherExpress Pro/100B
1829 # PCI Fast Ethernet adapters.
1831 # The `gx' device provides support for the Intel Pro/1000 Gigabit Ethernet
1832 # PCI adapters (82542, 82543-F, 82543-T).
1834 # The 'lge' device provides support for PCI gigabit ethernet adapters
1835 # based on the Level 1 LXT1001 NetCellerator chipset. This includes the
1836 # D-Link DGE-500SX, SMC TigerCard 1000 (SMC9462SX), and some Addtron cards.
1838 # The 'my' device provides support for the Myson MTD80X and MTD89X PCI
1839 # Fast Ethernet adapters.
1841 # The 'nge' device provides support for PCI gigabit ethernet adapters
1842 # based on the National Semiconductor DP83820 and DP83821 chipset. This
1843 # includes the SMC EZ Card 1000 (SMC9462TX), D-Link DGE-500T, Asante
1844 # FriendlyNet GigaNIX 1000TA and 1000TPC, the Addtron AEG320T, the
1845 # LinkSys EG1032 and EG1064, the Surecom EP-320G-TX and the Netgear GA622T.
1847 # The 'pcn' device provides support for PCI fast ethernet adapters based
1848 # on the AMD Am79c97x chipsets, including the PCnet/FAST, PCnet/FAST+,
1849 # PCnet/PRO and PCnet/Home. These were previously handled by the lnc
1850 # driver (and still will be if you leave this driver out of the kernel).
1852 # Te 're' device provides support for PCI GigaBit ethernet adapters based
1853 # on the RealTek 8169 chipset. It also supports the 8139C+ and is the
1854 # prefered driver for that chip.
1856 # The 'rl' device provides support for PCI fast ethernet adapters based
1857 # on the RealTek 8129/8139 chipset. Note that the RealTek driver defaults
1858 # to using programmed I/O to do register accesses because memory mapped
1859 # mode seems to cause severe lockups on SMP hardware. This driver also
1860 # supports the Accton EN1207D `Cheetah' adapter, which uses a chip called
1861 # the MPX 5030/5038, which is either a RealTek in disguise or a RealTek
1862 # workalike. Note that the D-Link DFE-530TX+ uses the RealTek chipset
1863 # and is supported by this driver, not the 'vr' driver.
1865 # The 'sf' device provides support for Adaptec Duralink PCI fast
1866 # ethernet adapters based on the Adaptec AIC-6915 "starfire" controller.
1867 # This includes dual and quad port cards, as well as one 100baseFX card.
1868 # Most of these are 64-bit PCI devices, except for one single port
1869 # card which is 32-bit.
1871 # The 'ste' device provides support for adapters based on the Sundance
1872 # Technologies ST201 PCI fast ethernet controller. This includes the
1875 # The 'sis' device provides support for adapters based on the Silicon
1876 # Integrated Systems SiS 900 and SiS 7016 PCI fast ethernet controller
1879 # The 'sk' device provides support for the SysKonnect SK-984x series
1880 # PCI gigabit ethernet NICs. This includes the SK-9841 and SK-9842
1881 # single port cards (single mode and multimode fiber) and the
1882 # SK-9843 and SK-9844 dual port cards (also single mode and multimode).
1883 # The driver will autodetect the number of ports on the card and
1884 # attach each one as a separate network interface.
1886 # The 'ti' device provides support for PCI gigabit ethernet NICs based
1887 # on the Alteon Networks Tigon 1 and Tigon 2 chipsets. This includes the
1888 # Alteon AceNIC, the 3Com 3c985, the Netgear GA620 and various others.
1889 # Note that you will probably want to bump up NMBCLUSTERS a lot to use
1892 # The 'tl' device provides support for the Texas Instruments TNETE100
1893 # series 'ThunderLAN' cards and integrated ethernet controllers. This
1894 # includes several Compaq Netelligent 10/100 cards and the built-in
1895 # ethernet controllers in several Compaq Prosignia, Proliant and
1896 # Deskpro systems. It also supports several Olicom 10Mbps and 10/100
1899 # The `tx' device provides support for the SMC 9432 TX, BTX and FTX cards.
1901 # The `txp' device provides support for the 3Com 3cR990 "Typhoon"
1904 # The `vr' device provides support for various fast ethernet adapters
1905 # based on the VIA Technologies VT3043 `Rhine I' and VT86C100A `Rhine II'
1906 # chips, including the D-Link DFE530TX (see 'rl' for DFE530TX+), the Hawking
1907 # Technologies PN102TX, and the AOpen/Acer ALN-320.
1909 # The `vx' device provides support for the 3Com 3C590 and 3C595
1912 # The `wb' device provides support for various fast ethernet adapters
1913 # based on the Winbond W89C840F chip. Note: this is not the same as
1914 # the Winbond W89C940F, which is an NE2000 clone.
1916 # The `wx' device provides support for the Intel Gigabit Ethernet
1917 # PCI card (`Wiseman').
1919 # The `xl' device provides support for the 3Com 3c900, 3c905 and
1920 # 3c905B (Fast) Etherlink XL cards and integrated controllers. This
1921 # includes the integrated 3c905B-TX chips in certain Dell Optiplex and
1922 # Dell Precision desktop machines and the integrated 3c905-TX chips
1923 # in Dell Latitude laptop docking stations.
1925 # The `fpa' device provides support for the Digital DEFPA PCI FDDI
1926 # adapter. pseudo-device fddi is also needed.
1928 # The `meteor' device is a PCI video capture board. It can also have the
1929 # following options:
1930 # options METEOR_ALLOC_PAGES=xxx preallocate kernel pages for data entry
1931 # figure (ROWS*COLUMN*BYTES_PER_PIXEL*FRAME+PAGE_SIZE-1)/PAGE_SIZE
1932 # options METEOR_DEALLOC_PAGES remove all allocated pages on close(2)
1933 # options METEOR_DEALLOC_ABOVE=xxx remove all allocated pages above the
1934 # specified amount. If this value is below the allocated amount no action
1936 # options METEOR_SYSTEM_DEFAULT={METEOR_PAL|METEOR_NTSC|METEOR_SECAM}, used
1937 # for initialization of fps routine when a signal is not present.
1939 # The 'bktr' device is a PCI video capture device using the Brooktree
1940 # bt848/bt848a/bt849a/bt878/bt879 chipset. When used with a TV Tuner it forms a
1941 # TV card, eg Miro PC/TV, Hauppauge WinCast/TV WinTV, VideoLogic Captivator,
1942 # Intel Smart Video III, AverMedia, IMS Turbo, FlyVideo.
1944 # options OVERRIDE_CARD=xxx
1945 # options OVERRIDE_TUNER=xxx
1946 # options OVERRIDE_MSP=1
1947 # options OVERRIDE_DBX=1
1948 # These options can be used to override the auto detection
1949 # The current values for xxx are found in src/sys/dev/bktr/bktr_card.h
1950 # Using sysctl(8) run-time overrides on a per-card basis can be made
1952 # options BROOKTREE_SYSTEM_DEFAULT=BROOKTREE_PAL
1954 # options BROOKTREE_SYSTEM_DEFAULT=BROOKTREE_NTSC
1955 # Specifes the default video capture mode.
1956 # This is required for Dual Crystal (28&35Mhz) boards where PAL is used
1957 # to prevent hangs during initialisation. eg VideoLogic Captivator PCI.
1959 # options BKTR_USE_PLL
1960 # PAL or SECAM users who have a 28Mhz crystal (and no 35Mhz crystal)
1961 # must enable PLL mode with this option. eg some new Bt878 cards.
1963 # options BKTR_GPIO_ACCESS
1964 # This enable IOCTLs which give user level access to the GPIO port.
1966 # options BKTR_NO_MSP_RESET
1967 # Prevents the MSP34xx reset. Good if you initialise the MSP in another OS first
1969 # options BKTR_430_FX_MODE
1970 # Switch Bt878/879 cards into Intel 430FX chipset compatibility mode.
1972 # options BKTR_SIS_VIA_MODE
1973 # Switch Bt878/879 cards into SIS/VIA chipset compatibility mode which is
1974 # needed for some old SiS and VIA chipset motherboards.
1975 # This also allows Bt878/879 chips to work on old OPTi (<1997) chipset
1976 # motherboards and motherboards with bad or incomplete PCI 2.1 support.
1977 # As a rough guess, old = before 1998
1979 # options BKTR_NEW_MSP34XX_DRIVER
1980 # Use new, more complete initialization scheme for the msp34* soundchip.
1981 # Should fix stereo autodetection if the old driver does only output
1985 # The oltr driver supports the following Olicom PCI token-ring adapters
1986 # OC-3136, OC-3137, OC-3139, OC-3140, OC-3141, OC-3540, OC-3250
1988 device ahc # AHA2940 and onboard AIC7xxx devices
1989 device ahd # AIC79xx devices
1990 device amd # AMD 53C974 (Tekram DC-390(T))
1991 device isp # Qlogic family
1992 device ispfw # Firmware for QLogic HBAs
1993 device ncr # NCR/Symbios Logic
1994 device sym # NCR/Symbios Logic (newer chipsets)
1995 device trm # Tekram DC395U/UW/F and DC315U
1999 # ISP_TARGET_MODE - enable target mode operation
2000 #options ISP_TARGET_MODE=1
2002 # Options used in dev/sym/ (Symbios SCSI driver).
2003 #options SYM_SETUP_LP_PROBE_MAP #-Low Priority Probe Map (bits)
2004 # Allows the ncr to take precedence
2005 # 1 (1<<0) -> 810a, 860
2006 # 2 (1<<1) -> 825a, 875, 885, 895
2007 # 4 (1<<2) -> 895a, 896, 1510d
2008 #options SYM_SETUP_SCSI_DIFF #-HVD support for 825a, 875, 885
2009 # disabled:0 (default), enabled:1
2010 #options SYM_SETUP_PCI_PARITY #-PCI parity checking
2011 # disabled:0, enabled:1 (default)
2012 #options SYM_SETUP_MAX_LUN #-Number of LUNs supported
2013 # default:8, range:[1..64]
2016 # MII bus support is required for some PCI 10/100 ethernet NICs,
2017 # namely those which use MII-compliant transceivers or implement
2018 # tranceiver control interfaces that operate like an MII. Adding
2019 # "device miibus0" to the kernel config pulls in support for
2020 # the generic miibus API and all of the PHY drivers, including a
2021 # generic one for PHYs that aren't specifically handled by an
2022 # individual driver.
2025 # PCI Ethernet NICs that use the common MII bus controller code.
2026 device bfe # Broadcom BCM440x 10/100 Ethernet
2027 device dc # DEC/Intel 21143 and various workalikes
2028 device fxp # Intel EtherExpress PRO/100B (82557, 82558)
2029 device my # Myson Fast Ethernet (MTD80X, MTD89X)
2030 device pcn # AMD Am79C97x PCI 10/100 NICs
2031 device re # RealTek 8139C+/8169
2032 device rl # RealTek 8129/8139
2033 device sbsh # Granch SBNI16 SHDSL modem
2034 device sf # Adaptec AIC-6915 (``Starfire'')
2035 device sis # Silicon Integrated Systems SiS 900/SiS 7016
2036 device ste # Sundance ST201 (D-Link DFE-550TX)
2037 device tl # Texas Instruments ThunderLAN
2038 device tx # SMC EtherPower II (83c17x ``EPIC'')
2039 device vr # VIA Rhine, Rhine II
2040 device wb # Winbond W89C840F
2041 device xl # 3Com 3c90x (``Boomerang'', ``Cyclone'')
2043 # PCI Ethernet NICs.
2044 device de # DEC/Intel DC21x4x (``Tulip'')
2045 device txp # 3Com 3cR990 (``Typhoon'')
2046 device vx # 3Com 3c590, 3c595 (``Vortex'')
2048 # Gigabit Ethernet NICs.
2049 device bge # Broadcom BCM570x (``Tigon III'')
2050 device em # Intel Pro/1000 (82542,82543,82544,82540)
2051 device gx # Intel Pro/1000 (82542, 82543)
2052 device lge # Level 1 LXT1001 (``Mercury'')
2053 device nge # NatSemi DP83820 and DP83821
2054 device sk # SysKonnect GEnesis, LinkSys EG1023, D-Link
2055 device ti # Alteon (``Tigon I'', ``Tigon II'')
2061 #The oltr driver in the ISA section will also find PCI cards.
2065 # Brooktree driver has been ported to the new I2C framework. Thus,
2066 # you'll need to have the following 3 lines in the kernel config.
2070 # The iic and smb devices are only needed if you want to control other
2071 # I2C slaves connected to the external connector of some cards.
2074 options BKTR_NEW_MSP34XX_DRIVER
2079 # pccard: pccard slots
2080 # pcic: isa/pccard bridge (OLDCARD)
2081 # cardbus/cbb: cardbus bridge (NEWCARD)
2087 # You may need to reset all pccards after resuming
2088 options PCIC_RESUME_RESET # reset after resume
2091 # Laptop/Notebook options:
2094 # apm under `Miscellaneous hardware'
2097 # For older notebooks that signal a powerfail condition (external
2098 # power supply dropped, or battery state low) by issuing an NMI:
2100 options POWERFAIL_NMI # make it beep instead of panicing
2105 # System Management Bus support is provided by the 'smbus' device.
2106 # Access to the SMBus device is via the 'smb' device (/dev/smb*),
2107 # which is a child of the 'smbus' device.
2109 # Supported devices:
2110 # smb standard io through /dev/smb*
2112 # Supported SMB interfaces:
2113 # iicsmb I2C to SMB bridge with any iicbus interface
2114 # bktr brooktree848 I2C hardware interface
2115 # intpm Intel PIIX4 (82371AB, 82443MX) Power Management Unit
2116 # alpm Acer Aladdin-IV/V/Pro2 Power Management Unit
2117 # ichsmb Intel ICH SMBus controller chips (82801AA, 82801AB, 82801BA)
2118 # viapm VIA VT82C586B,596,686A and VT8233 SMBus controllers
2119 # amdpm AMD 756 Power Management Unit
2121 device smbus # Bus support, required for smb below.
2134 # Philips i2c bus support is provided by the `iicbus' device.
2136 # Supported devices:
2137 # ic i2c network interface
2138 # iic i2c standard io
2139 # iicsmb i2c to smb bridge. Allow i2c i/o with smb commands.
2141 # Supported interfaces:
2142 # pcf Philips PCF8584 ISA-bus controller
2143 # bktr brooktree848 I2C software interface
2146 # iicbb generic I2C bit-banging code (needed by lpbb, bktr)
2148 device iicbus # Bus support, required for ic/iic/iicsmb below.
2153 device iicsmb # smb over i2c bridge
2155 device pcf0 at isa? port 0x320 irq 5
2157 #---------------------------------------------------------------------------
2160 # See /usr/share/examples/isdn/ROADMAP for an introduction to isdn4bsd.
2162 # i4b passive ISDN cards support contains the following hardware drivers:
2164 # isic - Siemens/Infineon ISDN ISAC/HSCX/IPAC chipset driver
2165 # iwic - Winbond W6692 PCI bus ISDN S/T interface controller
2166 # ifpi - AVM Fritz!Card PCI driver
2167 # ifpi2 - AVM Fritz!Card PCI driver Version 2
2168 # ihfc - Cologne Chip HFC ISA/ISA-PnP chipset driver
2169 # ifpnp - AVM Fritz!Card PnP driver
2170 # itjc - Siemens ISAC / TJNet Tiger300/320 chipset
2172 # i4b active ISDN cards support contains the following hardware drivers:
2174 # iavc - AVM B1 PCI, AVM B1 ISA, AVM T1
2176 # Note that the ``options'' (if given) and ``device'' lines must BOTH
2177 # be uncommented to enable support for a given card !
2179 # In addition to a hardware driver (and probably an option) the mandatory
2180 # ISDN protocol stack devices and the mandatory support device must be
2181 # enabled as well as one or more devices from the optional devices section.
2183 #---------------------------------------------------------------------------
2184 # isic driver (Siemens/Infineon chipsets)
2185 #---------------------------------------------------------------------------
2187 # ISA bus non-PnP Cards:
2188 # ----------------------
2190 # Teles S0/8 or Niccy 1008
2192 device isic0 at isa? iomem 0xd0000 irq 5 flags 1
2194 # Teles S0/16 or Creatix ISDN-S0 or Niccy 1016
2196 #device isic0 at isa? port 0xd80 iomem 0xd0000 irq 5 flags 2
2200 #device isic0 at isa? port 0xd80 irq 5 flags 3
2202 # AVM A1 or AVM Fritz!Card
2204 #device isic0 at isa? port 0x340 irq 5 flags 4
2206 # USRobotics Sportster ISDN TA intern
2208 #device isic0 at isa? port 0x268 irq 5 flags 7
2210 # ITK ix1 Micro ( < V.3, non-PnP version )
2212 #device isic0 at isa? port 0x398 irq 10 flags 18
2216 #device isic0 at isa? port 0x360 irq 10 flags 20
2218 # ISA bus PnP Cards:
2219 # ------------------
2222 options TEL_S0_16_3_P
2225 # Creatix ISDN-S0 P&P
2229 # Dr. Neuhaus Niccy Go@
2233 # Sedlbauer Win Speed
2241 # ELSA QuickStep 1000pro ISA
2245 # ITK ix1 Micro ( V.3, PnP version )
2249 # Siemens I-Surf 2.0
2250 options SIEMENS_ISURF2
2253 # Asuscom ISDNlink 128K ISAC
2254 options ASUSCOM_IPAC
2257 # Eicon Diehl DIVA 2.0 and 2.02
2264 # ELSA MicroLink ISDN/PCI (same as ELSA QuickStep 1000pro PCI)
2268 #---------------------------------------------------------------------------
2269 # ifpnp driver for AVM Fritz!Card ISA PnP
2270 #---------------------------------------------------------------------------
2272 # AVM Fritz!Card ISA PnP
2275 #---------------------------------------------------------------------------
2276 # ihfc driver for Cologne Chip ISA chipsets (experimental!)
2277 #---------------------------------------------------------------------------
2279 # Teles 16.3c ISA PnP
2280 # AcerISDN P10 ISA PnP
2281 # TELEINT ISDN SPEED No.1
2284 #---------------------------------------------------------------------------
2285 # ifpi driver for AVM Fritz!Card PCI 1.0 (2.0 unsupported!)
2286 #---------------------------------------------------------------------------
2288 # AVM Fritz!Card PCI 1.0
2291 #---------------------------------------------------------------------------
2292 # ifpi2 driver for AVM Fritz!Card PCI 2.0
2293 #---------------------------------------------------------------------------
2295 # AVM Fritz!Card PCI 2.0
2298 #---------------------------------------------------------------------------
2299 # iwic driver for Winbond W6692 chipset
2300 #---------------------------------------------------------------------------
2302 # ASUSCOM P-IN100-ST-D (and other Winbond W6692 based cards)
2305 #---------------------------------------------------------------------------
2306 # itjc driver for Simens ISAC / TJNet Tiger300/320 chipset
2307 #---------------------------------------------------------------------------
2309 # Traverse Technologies NETjet-S
2313 #---------------------------------------------------------------------------
2314 # iavc driver (AVM active cards, needs i4bcapi driver!)
2315 #---------------------------------------------------------------------------
2317 pseudo-device "i4bcapi" 2
2322 # AVM B1 ISA bus (PnP mode not supported!)
2323 #device iavc0 at isa? port 0x150 irq 5
2326 # ISDN Protocol Stack (mandatory)
2327 # -------------------------------
2329 # Q.921 / layer 2 - i4b passive cards D channel handling
2330 pseudo-device "i4bq921"
2332 # Q.931 / layer 3 - i4b passive cards D channel handling
2333 pseudo-device "i4bq931"
2335 # layer 4 - i4b common passive and active card handling
2341 # userland driver to do ISDN tracing (for passive cards only)
2342 pseudo-device "i4btrc" 4
2344 # userland driver to control the whole thing (mandatory)
2345 pseudo-device "i4bctl"
2347 # userland driver for access to raw B channel
2348 pseudo-device "i4brbch" 4
2350 # userland driver for telephony
2351 pseudo-device "i4btel" 2
2353 # network driver for IP over raw HDLC ISDN
2354 pseudo-device "i4bipr" 4
2355 # enable VJ header compression detection for ipr i/f
2357 # enable logging of the first n IP packets to isdnd (n=32 here)
2360 # network driver for sync PPP over ISDN - requires sppp
2361 pseudo-device "i4bisppp" 4
2366 # Parallel port bus support is provided by the `ppbus' device.
2367 # Multiple devices may be attached to the parallel port, devices
2368 # are automatically probed and attached when found.
2370 # Supported devices:
2371 # vpo Iomega Zip Drive
2372 # Requires SCSI disk support ('scbus' and 'da'); the best
2373 # performance is achieved with ports in EPP 1.9 mode.
2374 # lpt Parallel Printer
2375 # plip Parallel network interface
2376 # ppi General-purpose I/O ("Geek Port") + IEEE1284 I/O
2377 # pps Pulse per second Timing Interface
2378 # lpbb Philips official parallel port I2C bit-banging interface
2380 # Supported interfaces:
2381 # ppc ISA-bus parallel port interfaces.
2384 options PPC_PROBE_CHIPSET # Enable chipset specific detection
2385 # (see flags in ppc(4))
2386 options DEBUG_1284 # IEEE1284 signaling protocol debug
2387 options PERIPH_1284 # Makes your computer act as a IEEE1284
2388 # compliant peripheral
2389 options DONTPROBE_1284 # Avoid boot detection of PnP parallel devices
2390 options VP0_DEBUG # ZIP/ZIP+ debug
2391 options LPT_DEBUG # Printer driver debug
2392 options PPC_DEBUG # Parallel chipset level debug
2393 options PLIP_DEBUG # Parallel network IP interface debug
2394 options PCFCLOCK_VERBOSE # Verbose pcfclock driver
2395 options PCFCLOCK_MAX_RETRIES=5 # Maximum read tries (default 10)
2397 device ppc0 at isa? irq 7
2407 # Kernel BOOTP support
2409 options BOOTP # Use BOOTP to obtain IP address/hostname
2410 options BOOTP_NFSROOT # NFS mount root filesystem using BOOTP info
2411 options BOOTP_NFSV3 # Use NFS v3 to NFS mount root
2412 options BOOTP_COMPAT # Workaround for broken bootp daemons.
2413 options BOOTP_WIRED_TO=fxp0 # Use interface fxp0 for BOOTP
2416 # Add tie-ins for a hardware watchdog. This only enable the hooks;
2417 # the user must still supply the actual driver.
2422 # Set the number of PV entries per process. Increasing this can
2423 # stop panics related to heavy use of shared memory. However, that can
2424 # (combined with large amounts of physical memory) cause panics at
2425 # boot time due the kernel running out of VM space.
2427 # If you're tweaking this, you might also want to increase the sysctls
2428 # "vm.v_free_min", "vm.v_free_reserved", and "vm.v_free_target".
2430 # The value below is the one more than the default.
2432 options PMAP_SHPGPERPROC=201
2435 # Change the size of the kernel virtual address space. Due to
2436 # constraints in loader(8) on i386, this must be a multiple of 4.
2437 # 256 = 1 GB of kernel address space. Increasing this also causes
2438 # a reduction of the address space in user processes. 512 splits
2439 # the 4GB cpu address space in half (2GB user, 2GB kernel).
2441 options KVA_PAGES=260
2444 # Disable swapping. This option removes all code which actually performs
2445 # swapping, so it's not possible to turn it back on at run-time.
2447 # This is sometimes usable for systems which don't have any swap space
2448 # (see also sysctls "vm.defer_swapspace_pageouts" and
2449 # "vm.disable_swapspace_pageouts")
2451 #options NO_SWAPPING
2453 # Set the number of sf_bufs to allocate. sf_bufs are virtual buffers
2454 # for sendfile(2) that are used to map file VM pages, and normally
2455 # default to a quantity that is roughly 16*MAXUSERS+512. You would
2456 # typically want about 4 of these for each simultaneous file send.
2458 options NSFBUFS=1024
2460 # Set the size of the buffer cache KVM reservation, in buffers. This is
2461 # scaled by approximately 16384 bytes. The system will auto-size the buffer
2462 # cache if this option is not specified.
2466 # Set the size of the mbuf KVM reservation, in clusters. This is scaled
2467 # by approximately 2048 bytes. The system will auto-size the mbuf area
2468 # to (512 + maxusers*16) if this option is not specified.
2469 # maxusers is in turn computed at boot time depending on available memory
2470 # or set to the value specified by "options MAXUSERS=x" (x=0 means
2472 # So, to take advantage of autoscaling, you have to remove both
2473 # NMBCLUSTERS and MAXUSERS (and NMBUFS) from your kernel config.
2475 options NMBCLUSTERS=1024
2477 # Set the number of mbufs available in the system. Each mbuf
2478 # consumes 256 bytes. The system will autosize this (to 4 times
2479 # the number of NMBCLUSTERS, depending on other constraints)
2480 # if this option is not specified.
2484 # Tune the kernel malloc area parameters. VM_KMEM_SIZE represents the
2485 # minimum, in bytes, and is typically (12*1024*1024) (12MB).
2486 # VM_KMEM_SIZE_MAX represents the maximum, typically 200 megabytes.
2487 # VM_KMEM_SIZE_SCALE can be set to adjust the auto-tuning factor, which
2488 # typically defaults to 4 (kernel malloc area size is physical memory
2489 # divided by the scale factor).
2491 options VM_KMEM_SIZE="(10*1024*1024)"
2492 options VM_KMEM_SIZE_MAX="(100*1024*1024)"
2493 options VM_KMEM_SIZE_SCALE="4"
2495 # Tune the buffer cache maximum KVA reservation, in bytes. The maximum is
2496 # usually capped at 200 MB, effecting machines with > 1GB of ram. Note
2497 # that the buffer cache only really governs write buffering and disk block
2498 # translations. The VM page cache is our primary disk cache and is not
2499 # effected by the size of the buffer cache.
2501 options VM_BCACHE_SIZE_MAX="(100*1024*1024)"
2503 # Tune the swap zone KVA reservation, in bytes. The default is typically
2504 # 70 MB, giving the system the ability to manage a maximum of 28GB worth
2505 # of swapped out data.
2507 options VM_SWZONE_SIZE_MAX="(50*1024*1024)"
2510 # Enable extra debugging code for locks. This stores the filename and
2511 # line of whatever acquired the lock in the lock itself, and change a
2512 # number of function calls to pass around the relevant data. This is
2513 # not at all useful unless you are debugging lock code. Also note
2514 # that it is likely to break e.g. fstat(1) unless you recompile your
2515 # userland with -DDEBUG_LOCKS as well.
2519 # Set the amount of time (in seconds) the system will wait before
2520 # rebooting automatically when a kernel panic occurs. If set to (-1),
2521 # the system will wait indefinitely until a key is pressed on the
2523 options PANIC_REBOOT_WAIT_TIME=16
2525 # Attempt to bypass the buffer cache and put data directly into the
2526 # userland buffer for read operation when O_DIRECT flag is set on the
2527 # file. Both offset and length of the read operation must be
2528 # multiples of the physical media sector size.
2532 # Specify a lower limit for the number of swap I/O buffers. They are
2533 # (among other things) used when bypassing the buffer cache due to
2534 # DIRECTIO kernel option enabled and O_DIRECT flag set on file.
2536 #options NSWBUF_MIN=120
2539 # SysVR4 ABI emulation
2541 # The svr4 ABI emulator can be statically compiled into the kernel or loaded as
2543 # The STREAMS network emulation code can also be compiled statically or as a
2544 # module. If loaded as a module, it must be loaded before the svr4 module
2545 # (the /usr/sbin/svr4 script does this for you). If compiling statically,
2546 # the `streams' pseudo-device must be configured into any kernel which also
2547 # specifies COMPAT_SVR4. It is possible to have a statically-configured
2548 # STREAMS device and a dynamically loadable svr4 emulator; the /usr/sbin/svr4
2549 # script understands that it doesn't need to load the `streams' module under
2550 # those circumstances.
2551 # Caveat: At this time, `options KTRACE' is required for the svr4 emulator
2552 # (whether static or dynamic).
2554 options COMPAT_SVR4 # build emulator statically
2555 options DEBUG_SVR4 # enable verbose debugging
2556 pseudo-device streams # STREAMS network driver (required for svr4).
2558 # The 'asr' driver provides support for current DPT/Adaptec SCSI RAID
2559 # controllers (SmartRAID V and VI and later).
2560 # These controllers require the CAM infrastructure.
2564 # The 'dpt' driver provides support for DPT controllers (http://www.dpt.com/).
2565 # These have hardware RAID-{0,1,5} support, and do multi-initiator I/O.
2566 # The DPT controllers are commonly re-licensed under other brand-names -
2567 # some controllers by Olivetti, Dec, HP, AT&T, SNI, AST, Alphatronic, NEC and
2568 # Compaq are actually DPT controllers.
2570 # See src/sys/dev/dpt for debugging and other subtle options.
2571 # DPT_MEASURE_PERFORMANCE Enables a set of (semi)invasive metrics. Various
2572 # instruments are enabled. The tools in
2573 # /usr/sbin/dpt_* assume these to be enabled.
2574 # DPT_HANDLE_TIMEOUTS Normally device timeouts are handled by the DPT.
2575 # If you ant the driver to handle timeouts, enable
2576 # this option. If your system is very busy, this
2577 # option will create more trouble than solve.
2578 # DPT_TIMEOUT_FACTOR Used to compute the excessive amount of time to
2579 # wait when timing out with the above option.
2580 # DPT_DEBUG_xxxx These are controllable from sys/dev/dpt/dpt.h
2581 # DPT_LOST_IRQ When enabled, will try, once per second, to catch
2582 # any interrupt that got lost. Seems to help in some
2583 # DPT-firmware/Motherboard combinations. Minimal
2584 # cost, great benefit.
2585 # DPT_RESET_HBA Make "reset" actually reset the controller
2586 # instead of fudging it. Only enable this if you
2587 # are 100% certain you need it.
2592 #!CAM# options DPT_MEASURE_PERFORMANCE
2593 #!CAM# options DPT_HANDLE_TIMEOUTS
2594 options DPT_TIMEOUT_FACTOR=4
2595 options DPT_LOST_IRQ
2596 options DPT_RESET_HBA
2597 options DPT_ALLOW_MEMIO
2600 # Compaq "CISS" RAID controllers (SmartRAID 5* series)
2601 # These controllers have a SCSI-like interface, and require the
2602 # CAM infrastructure.
2607 # Intel Integrated RAID controllers.
2608 # This driver was developed and is maintained by Intel. Contacts
2609 # at Intel for this driver are
2610 # "Kannanthanam, Boji T" <boji.t.kannanthanam@intel.com> and
2611 # "Leubner, Achim" <achim.leubner@intel.com>.
2616 # Mylex AcceleRAID and eXtremeRAID controllers with v6 and later
2617 # firmware. These controllers have a SCSI-like interface, and require
2618 # the CAM infrastructure.
2629 # General USB code (mandatory for USB)
2634 # Generic USB device driver
2636 # Human Interface Device (anything with buttons and dials)
2642 # USB Iomega Zip 100 Drive (Requires scbus and da)
2648 # USB Rio (MP3 Player)
2660 # ADMtek USB ethernet. Supports the LinkSys USB100TX,
2661 # the Billionton USB100, the Melco LU-ATX, the D-Link DSB-650TX
2662 # and the SMC 2202USB. Also works with the ADMtek AN986 Pegasus
2666 # CATC USB-EL1201A USB ethernet. Supports the CATC Netmate
2667 # and Netmate II, and the Belkin F5U111.
2670 # Kawasaki LSI ethernet. Supports the LinkSys USB10T,
2671 # Entrega USB-NET-E45, Peracom Ethernet Adapter, the
2672 # 3Com 3c19250, the ADS Technologies USB-10BT, the ATen UC10T,
2673 # the Netgear EA101, the D-Link DSB-650, the SMC 2102USB
2674 # and 2104USB, and the Corega USB-T.
2677 # debugging options for the USB subsystem
2682 options UKBD_DFLT_KEYMAP # specify the built-in keymap
2683 makeoptions UKBD_DFLT_KEYMAP=it.iso
2686 device firewire # Firewire bus code
2687 device sbp # SCSI over Firewire (Requires scbus and da)
2688 device fwe # Ethernet over Firewire (non-standard!)
2690 # dcons support (Dumb Console Device)
2691 device dcons # dumb console driver
2692 device dcons_crom # FireWire attachment
2693 options DCONS_BUF_SIZE=16384 # buffer size
2694 options DCONS_POLL_HZ=100 # polling rate
2695 options DCONS_FORCE_CONSOLE=1 # force to be the primary console
2696 options DCONS_FORCE_GDB=1 # force to be the gdb device
2698 #####################################################################
2701 # This is a port of the openbsd crypto framework. Include this when
2702 # configuring IPsec and when you have a h/w crypto device to accelerate
2703 # user applications that link to openssl.
2705 # Drivers are ports from openbsd with some simple enhancements that have
2706 # been fed back to openbsd (and hopefully will be included).
2708 pseudo-device crypto # core crypto support
2709 pseudo-device cryptodev # /dev/crypto for access to h/w
2711 device rndtest # FIPS 140-2 entropy tester
2713 device hifn # Hifn 7951, 7781, etc.
2714 options HIFN_DEBUG # enable debugging support: hw.hifn.debug
2715 options HIFN_RNDTEST # enable rndtest support
2717 device ubsec # Broadcom 5501, 5601, 58xx
2718 options UBSEC_DEBUG # enable debugging support: hw.ubsec.debug
2719 options UBSEC_RNDTEST # enable rndtest support
2721 device acpica # basic ACPI support
2724 # mgadrm: AGP Matrox G200, G400, G450, G550
2725 # tdfxdrm: 3dfx Voodoo 3/4/5 and Banshee
2726 # r128drm: ATI Rage 128
2727 # radeondrm: ATI Radeon up to 9000/9100
2728 # DRM_DEBUG: include debug printfs, very slow
2730 # mga requires AGP in the kernel, and it is recommended
2731 # for AGP r128 and radeon cards.
2741 # Embedded system options:
2743 # An embedded system might want to run something other than init.
2744 options INIT_PATH="/sbin/init:/stand/sysinstall"
2747 options BUS_DEBUG # enable newbus debugging
2748 options DEBUG_VFS_LOCKS # enable vfs lock debugging
2749 options NPX_DEBUG # enable npx debugging (FPU/math emu)
2751 # More undocumented options for linting.
2752 # Note that documenting these are not considered an affront.
2754 options AHC_DUMP_EEPROM
2755 options AHC_TMODE_ENABLE
2756 options CAM_DEBUG_DELAY
2757 options CLUSTERDEBUG
2758 options COMPAT_LINUX
2759 options CPU_UPGRADE_HW_CACHE
2762 #options DISABLE_PSE
2763 options ENABLE_ALART
2764 options ENABLE_VFS_IOOPT
2766 options FB_INSTALL_CDEV
2767 options FE_8BIT_SUPPORT
2768 options I4B_SMP_WORKAROUND
2769 options I586_PMC_GUPROF=0x70000
2771 options KBDIO_DEBUG=2
2772 options KBD_MAXRETRY=4
2773 options KBD_MAXWAIT=6
2774 options KBD_RESETDELAY=201
2778 options NETATALKDEBUG
2779 #options OLTR_NO_BULLSEYE_MAC
2780 #options OLTR_NO_HAWKEYE_MAC
2781 #options OLTR_NO_TMS_MAC
2783 options SCSI_NCR_DEBUG
2784 options SCSI_NCR_MAX_SYNC=10000
2785 options SCSI_NCR_MAX_WIDE=1
2786 options SCSI_NCR_MYADDR=7
2787 options SC_DEBUG_LEVEL
2788 options SC_RENDER_DEBUG
2789 options SHOW_BUSYBUFS # List buffers that prevent root unmount
2790 options SIMPLELOCK_DEBUG
2792 options SLIP_IFF_OPTS
2794 options TIMER_FREQ="((14318182+6)/12)"
2795 options VFS_BIO_DEBUG
2800 options KTR_CPUMASK=1
2801 options KTR_COMPILE=(KTR_ALL) # Every trace class, see sys/ktr.h for
2802 # the different class numbers
2803 options KTR_ENTRIES=1024
2804 options KTR_VERBOSE=1
projects / dragonfly.git / blob