2 # X86_64_LINT -- config file for checking all the sources, tries to pull in
3 # as much of the source tree as it can.
5 # $FreeBSD: src/sys/i386/conf/LINT,v 1.749.2.144 2003/06/04 17:56:59 sam Exp $
7 # See the kernconf(5) manual page for more information on the format of
10 # NB: You probably don't want to try running a kernel built from this
11 # file. Instead, you should start from X86_64_GENERIC, and add options
12 # from this file as required.
15 # These directives are mandatory. The machine directive specifies the
16 # platform and the machine_arch directive specifies the cpu architecture.
23 # This is the ``identification'' of the kernel. Usually this should
24 # be the same as the name of your kernel.
29 # The `maxusers' parameter controls the static sizing of a number of
30 # internal system tables by a formula defined in subr_param.c. Setting
31 # maxusers to 0 will cause the system to auto-size based on physical
37 # The `makeoptions' parameter allows variables to be passed to the
38 # generated Makefile in the build area.
40 # CONF_CFLAGS gives some extra compiler flags that are added to ${CFLAGS}
41 # after most other flags. Here we use it to inhibit use of non-optimal
42 # gcc builtin functions (e.g., memcmp).
44 # DEBUG happens to be magic.
45 # The following is equivalent to 'config -g KERNELNAME' and creates
46 # 'kernel.debug' compiled with -g debugging as well as a normal
47 # 'kernel'. Use 'make install.debug' to install the debug kernel
48 # but that isn't normally necessary as the debug symbols are not loaded
49 # by the kernel and are not useful there anyway.
51 # KERNEL can be overridden so that you can change the default name of your
54 # MODULES_OVERRIDE can be used to limit modules built to a specific list.
56 # INSTALLSTRIPPED can be set to cause installkernel to install stripped
57 # kernels and modules rather than a kernel and modules with debug symbols.
59 # INSTALLSTRIPPEDMODULES can be set to allow a full debug kernel to be
60 # installed, but to strip the installed modules.
62 makeoptions CONF_CFLAGS=-fno-builtin #Don't allow use of memcmp, etc.
63 #makeoptions DEBUG=-g #Build kernel with gdb(1) debug symbols
64 #makeoptions KERNEL=foo #Build kernel "foo" and install "/foo"
65 # Only build Linux API modules and plus those parts of the sound system I need.
66 #makeoptions MODULES_OVERRIDE="linux sound/snd sound/pcm"
67 #makeoptions INSTALLSTRIPPED=1
68 #makeoptions INSTALLSTRIPPEDMODULES=1
71 # Certain applications can grow to be larger than the 128M limit
72 # that DragonFly initially imposes. Below are some options to
73 # allow that limit to grow to 256MB, and can be increased further
74 # with changing the parameters. MAXDSIZ is the maximum that the
75 # limit can be set to, and the DFLDSIZ is the default value for
76 # the limit. MAXSSIZ is the maximum that the stack limit can be
77 # set to. You might want to set the default lower than the max,
78 # and explicitly set the maximum with a shell command for processes
79 # that regularly exceed the limit like INND.
81 options MAXDSIZ="(256*1024*1024)"
82 options MAXSSIZ="(256*1024*1024)"
83 options DFLDSIZ="(256*1024*1024)"
86 # BLKDEV_IOSIZE sets the default block size used in user block
87 # device I/O. Note that this value will be overridden by the label
88 # when specifying a block device from a label with a non-0
89 # partition blocksize. The default is PAGE_SIZE.
91 options BLKDEV_IOSIZE=8192
93 # This allows you to actually store this configuration file into
94 # the kernel binary itself, where it may be later read by saying:
95 # strings -n 3 /kernel | sed -n 's/^___//p' > MYKERNEL
97 options INCLUDE_CONFIG_FILE # Include this file in kernel
100 # The root device and filesystem type can be compiled in;
101 # this provides a fallback option if the root device cannot
102 # be correctly guessed by the bootstrap code, or an override if
103 # the RB_DFLTROOT flag (-r) is specified when booting the kernel.
105 options ROOTDEVNAME=\"ufs:da0s2e\"
107 #####################################################################
113 # Options for CPU features.
115 # CPU_DISABLE_AVX disables AVX instruction set.
117 options CPU_DISABLE_AVX
119 #####################################################################
120 # COMPATIBILITY OPTIONS
123 # Implement system calls compatible with 4.3BSD and older versions of
124 # FreeBSD. You probably do NOT want to remove this as much current code
125 # still relies on the 4.3 emulation.
129 # Enable NDIS binary driver support
134 # These three options provide support for System V Interface
135 # Definition-style interprocess communication, in the form of shared
136 # memory, semaphores, and message queues, respectively.
138 # System V shared memory and tunable parameters
139 options SHMMIN=2 # min shared memory segment size (bytes)
140 options SHMMNI=33 # max number of shared memory identifiers
141 options SHMSEG=9 # max shared memory segments per process
143 # System V semaphores and tunable parameters
144 options SEMMAP=31 # amount of entries in semaphore map
145 options SEMMNI=11 # number of semaphore identifiers in the system
146 options SEMMNS=61 # number of semaphores in the system
147 options SEMMNU=31 # number of undo structures in the system
148 options SEMMSL=61 # max number of semaphores per id
149 options SEMOPM=101 # max number of operations per semop call
150 options SEMUME=11 # max number of undo entries per process
152 # System V message queues and tunable parameters
153 options MSGMNB=2049 # max characters per message queue
154 options MSGMNI=41 # max number of message queue identifiers
155 options MSGSEG=2049 # max number of message segments in the system
156 options MSGSSZ=16 # size of a message segment MUST be power of 2
157 options MSGTQL=41 # max amount of messages in the system
159 #####################################################################
163 # Enable the kernel debugger.
168 # Print a stack trace on kernel panic.
173 # Don't drop into DDB for a panic. Intended for unattended operation
174 # where you may want to drop to DDB from the console, but still want
175 # the machine to recover from a panic
177 options DDB_UNATTENDED
180 # If using GDB remote mode to debug the kernel, there's a non-standard
181 # extension to the remote protocol that can be used to use the serial
182 # port as both the debugging port and the system console. It's non-
183 # standard and you're on your own if you enable it. See also the
184 # "remotechat" variables in the DragonFly specific version of gdb.
186 options GDB_REMOTE_CHAT
189 # KTRACE enables the system-call tracing facility ktrace(2).
191 options KTRACE #kernel tracing
194 # The INVARIANTS option is used in a number of source files to enable
195 # extra sanity checking of internal structures. This support is not
196 # enabled by default because of the extra time it would take to check
197 # for these conditions, which can only occur as a result of
198 # programming errors.
203 # The DIAGNOSTIC option is used to enable extra debugging information
204 # from some parts of the kernel. As this makes everything more noisy,
205 # it is disabled by default.
210 # PERFMON causes the driver for Pentium/Pentium Pro performance counters
211 # to be compiled. See perfmon(4) for more information.
217 # This option let some drivers co-exist that can't co-exist in a running
218 # system. This is used to be able to compile all kernel code in one go for
219 # quality assurance purposes (like this file, which the option takes it name
222 options COMPILING_LINT
225 # XXX - this doesn't belong here.
226 # Allow ordinary users to take the console - this is useful for X.
229 #####################################################################
234 # Only the INET (Internet) family is officially supported in DragonFly.
235 # Source code for the NS (Xerox Network Service) is provided for amusement
238 options INET #Internet communications protocols
239 options INET6 #IPv6 communications protocols
240 options IPSEC #IP security
241 options IPSEC_ESP #IP security (crypto; define w/ IPSEC)
242 options IPSEC_DEBUG #debug for IP security
244 # Set IPSEC_FILTERGIF to force packets coming through a gif tunnel
245 # to be processed by any configured packet filtering (ipfw).
246 # The default is that packets coming from a tunnel are _not_ processed;
247 # they are assumed trusted.
249 # Note that enabling this can be problematic as there are no mechanisms
250 # in place for distinguishing packets coming out of a tunnel (e.g. no
251 # encX devices as found on openbsd).
253 #options IPSEC_FILTERGIF #filter ipsec packets from a tunnel
256 # Experimental IPsec implementation that uses the kernel crypto
257 # framework. This cannot be configured together with IPSEC and
258 # (currently) supports only IPv4. To use this you must also
259 # configure the crypto device (see below). Note that with this
260 # you get all the IPsec protocols (e.g. there is no FAST_IPSEC_ESP).
261 # IPSEC_DEBUG is used, as above, to configure debugging support
262 # within the IPsec protocols.
264 #options FAST_IPSEC #new IPsec
266 options MPLS #Multi-Protocol Label Switching
270 # NETSMB enables support for SMB protocol, it requires LIBMCHAIN and LIBICONV
272 # NETSMBCRYPTO enables support for encrypted passwords.
273 options NETSMB #SMB/CIFS requester
274 options NETSMBCRYPTO #encrypted password support for SMB
276 # mchain library. It can be either loaded as KLD or compiled into kernel
277 options LIBMCHAIN #mbuf management library
279 # netgraph(4). Enable the base netgraph code with the NETGRAPH option.
280 # Individual node types can be enabled with the corresponding option
281 # listed below; however, this is not strictly necessary as netgraph
282 # will automatically load the corresponding KLD module if the node type
283 # is not already compiled into the kernel. Each type below has a
284 # corresponding man page, e.g., ng_async(4).
285 options NETGRAPH #netgraph(4) system
286 options NETGRAPH_ASYNC
288 options NETGRAPH_BRIDGE
289 options NETGRAPH_CISCO
290 options NETGRAPH_ECHO
291 options NETGRAPH_EIFACE
292 options NETGRAPH_ETHER
294 options NETGRAPH_FRAME_RELAY
295 options NETGRAPH_HOLE
296 options NETGRAPH_IFACE
297 options NETGRAPH_KSOCKET
298 options NETGRAPH_L2TP
300 # MPPC compression requires proprietary files (not included)
301 #options NETGRAPH_MPPC_COMPRESSION
302 options NETGRAPH_MPPC_ENCRYPTION
303 options NETGRAPH_ONE2MANY
305 options NETGRAPH_PPPOE
306 options NETGRAPH_PPTPGRE
307 options NETGRAPH_RFC1490
308 options NETGRAPH_SOCKET
314 device mn # Munich32x/Falc54 Nx64kbit/sec cards.
317 # Network interfaces:
318 # The `loop' pseudo-device is MANDATORY when networking is enabled.
319 # The `ether' pseudo-device provides generic code to handle
320 # Ethernets; it is MANDATORY when a Ethernet device driver is
322 # The `sppp' pseudo-device serves a similar role for certain types
323 # of synchronous PPP links (like `ar').
324 # The `sl' pseudo-device implements the Serial Line IP (SLIP) service.
325 # The `ppp' pseudo-device implements the Point-to-Point Protocol.
326 # The `bpf' pseudo-device enables the Berkeley Packet Filter. Be
327 # aware of the legal and administrative consequences of enabling this
328 # option. The number of devices determines the maximum number of
329 # simultaneous BPF clients programs runnable.
330 # The `disc' pseudo-device implements a minimal network interface,
331 # which throws away all packets sent and never receives any. It is
332 # included for testing purposes. This shows up as the 'ds' interface.
333 # The `tun' pseudo-device implements (user-)ppp and nos-tun
334 # The `gif' pseudo-device implements IPv6 over IP4 tunneling,
335 # IPv4 over IPv6 tunneling, IPv4 over IPv4 tunneling and
336 # IPv6 over IPv6 tunneling.
337 # The `gre' device implements two types of IP4 over IP4 tunneling:
338 # GRE and MOBILE, as specified in the RFC1701 and RFC2004.
339 # The `faith' pseudo-device captures packets sent to it and diverts them
340 # to the IPv4/IPv6 translation daemon.
341 # The `stf' device implements 6to4 encapsulation.
342 # The `ef' pseudo-device provides support for multiple ethernet frame types
343 # specified via ETHER_* options. See ef(4) for details.
345 # The PPP_BSDCOMP option enables support for compress(1) style entire
346 # packet compression, the PPP_DEFLATE is for zlib/gzip style compression.
347 # PPP_FILTER enables code for filtering the ppp data stream and selecting
348 # events for resetting the demand dial activity timer - requires bpf.
349 # See pppd(8) for more details.
351 pseudo-device ether #Generic Ethernet
352 pseudo-device vlan 1 #VLAN support
353 pseudo-device bridge #Bridging support
354 pseudo-device sppp #Generic Synchronous PPP
355 pseudo-device loop #Network loopback device
356 pseudo-device bpf #Berkeley packet filter
357 pseudo-device disc #Discard device (ds0, ds1, etc)
358 pseudo-device tap #Ethernet tunnel network interface
359 pseudo-device tun #Tunnel driver (ppp(8), nos-tun(8))
360 pseudo-device sl 2 #Serial Line IP
361 pseudo-device gre #IP over IP tunneling
362 pseudo-device ppp 2 #Point-to-point protocol
363 options PPP_BSDCOMP #PPP BSD-compress support
364 options PPP_DEFLATE #PPP zlib/deflate/gzip support
365 options PPP_FILTER #enable bpf filtering (needs bpf)
368 pseudo-device gif #IPv6 and IPv4 tunneling
369 pseudo-device faith 1 #for IPv6 and IPv4 translation
370 pseudo-device stf #6to4 IPv6 over IPv4 encapsulation
373 # Internet family options:
375 # MROUTING enables the kernel multicast packet forwarder, which works
378 # PIM enables Protocol Independent Multicast in the kernel.
379 # Requires MROUTING enabled.
381 # IPFIREWALL enables support for IP firewall construction, in
382 # conjunction with the `ipfw' program. IPFIREWALL_VERBOSE sends
383 # logged packets to the system logger. IPFIREWALL_VERBOSE_LIMIT
384 # limits the number of times a matching entry can be logged.
386 # WARNING: IPFIREWALL defaults to a policy of "deny ip from any to any"
387 # and if you do not add other rules during startup to allow access,
388 # YOU WILL LOCK YOURSELF OUT. It is suggested that you set firewall_type=open
389 # in /etc/rc.conf when first enabling this feature, then refining the
390 # firewall rules in /etc/rc.firewall after you've tested that the new kernel
391 # feature works properly.
393 # IPFIREWALL3 is based on a newer version of FreeBSD's ipfw2, along with
394 # some enhancements. See ipfw3(4).
396 # IPFIREWALL_DEFAULT_TO_ACCEPT causes the default rule (at boot) to
397 # allow everything. Use with care, if a cracker can crash your
398 # firewall machine, they can get to your protected machines. However,
399 # if you are using it as an as-needed filter for specific problems as
400 # they arise, then this may be for you. Changing the default to 'allow'
401 # means that you won't get stuck if the kernel and /sbin/ipfw binary get
404 # IPDIVERT enables the divert IP sockets, used by ``ipfw divert''
406 # IPSTEALTH enables code to support stealth forwarding (i.e., forwarding
407 # packets without touching the ttl). This can be useful to hide firewalls
408 # from traceroute and similar tools.
410 # TCPDEBUG is undocumented.
412 # ICMPPRINTFS enables ICMP to do extra debug prints.
414 options MROUTING # Multicast routing
415 options PIM # Protocol Independent Multicast
416 options IPFIREWALL #firewall
417 options IPFIREWALL_DEBUG #debug prints
418 options IPFIREWALL_VERBOSE #enable logging to syslogd(8)
419 options IPFIREWALL_VERBOSE_LIMIT=100 #limit verbosity
420 options IPFIREWALL_DEFAULT_TO_ACCEPT #allow everything by default
421 options IPV6FIREWALL #firewall for IPv6
422 options IPV6FIREWALL_VERBOSE
423 options IPV6FIREWALL_VERBOSE_LIMIT=100
424 options IPV6FIREWALL_DEFAULT_TO_ACCEPT
425 options IPDIVERT #divert sockets
426 options IPSTEALTH #support for stealth forwarding
439 # The MBUF_STRESS_TEST option enables options which create
440 # various random failures / extreme cases related to mbuf
441 # functions. See the mbuf(9) manpage for a list of available
443 options MBUF_STRESS_TEST
445 # Statically link in accept filters
446 options ACCEPT_FILTER_DATA
447 options ACCEPT_FILTER_HTTP
449 # TCP_SIGNATURE adds support for RFC 2385 (TCP-MD5) digests. These are
450 # carried in TCP option 19. This option is commonly used to protect
451 # TCP sessions (e.g. BGP) where IPSEC is not available nor desirable.
452 # This is enabled on a per-socket basis using the TCP_SIGNATURE_ENABLE
454 # This requires the use of 'device crypto', 'options IPSEC'
455 # or 'device cryptodev'.
456 options TCP_SIGNATURE #include support for RFC 2385
459 # TCP_DROP_SYNFIN adds support for ignoring TCP packets with SYN+FIN. This
460 # prevents nmap et al. from identifying the TCP/IP stack, but breaks support
461 # for RFC1644 extensions and is not recommended for web servers.
463 options TCP_DROP_SYNFIN #drop TCP packets with SYN+FIN
465 # ICMP_BANDLIM enables icmp error response bandwidth limiting. You
466 # typically want this option as it will help protect the machine from
467 # D.O.S. packet attacks.
471 # DUMMYNET enables the "dummynet" bandwidth limiter. You need
472 # IPFIREWALL as well. See the dummynet(4) and ipfw(8) manpages for more info.
475 options DUMMYNET_DEBUG
477 # IFPOLL_ENABLE adds support for mixed interrupt-polling handling
478 # of network device drivers, which has significant benefits in terms
479 # of robustness to overloads and responsivity, as well as permitting
480 # accurate scheduling of the CPU time between kernel network processing
481 # and other activities. The drawback is a moderate (up to 1/pollhz seconds)
482 # potential increase in response times. See polling(4) for further details.
484 # IFPOLL_ENABLE adds hardware queues' based polling
485 options IFPOLL_ENABLE
487 #####################################################################
491 # Only the root, /usr, and /tmp filesystems need be statically
492 # compiled; everything else will be automatically loaded at mount
493 # time. (Exception: the UFS family --- FFS, and MFS ---
494 # cannot currently be demand-loaded.) Some people still prefer
495 # to statically compile other filesystems as well.
497 # NB: The PORTAL filesystem is known to be
498 # buggy, and WILL panic your system if you attempt to do anything with
499 # it. It is included here as an incentive for some enterprising
500 # soul to sit down and fix it.
503 # One of these is mandatory:
504 options FFS #Fast filesystem
505 options MFS #Memory filesystem
506 options NFS #Network filesystem
508 # The rest are optional:
509 #options NFS_NOSERVER #Disable the NFS-server code.
510 options AUTOFS #Automounter filesystem
511 options CD9660 #ISO 9660 filesystem
512 options HAMMER #HAMMER filesystem
513 options HPFS #OS/2 File system
514 options MSDOSFS #MS DOS filesystem
515 options NTFS #NT filesystem
516 options NULLFS #NULL filesystem
517 options PORTAL #Portal filesystem
518 options PROCFS #Process filesystem
519 options PUFFS #Userspace file systems (e.g. ntfs-3g & sshfs)
520 options SMBFS #SMB/CIFS filesystem
521 options TMPFS #Temporary filesystem
522 options UDF #UDF filesystem
524 # The xFS_ROOT options REQUIRE the associated ``options xFS''
525 options FFS_ROOT #FFS usable as root device
526 options NFS_ROOT #NFS usable as root device
528 # Soft updates is technique for improving UFS filesystem speed and
529 # making abrupt shutdown less risky.
532 # Directory hashing improves the speed of operations on very large
533 # directories at the expense of some memory.
536 # Make space in the kernel for a root filesystem on a md device.
537 # Define to the number of kilobytes to reserve for the filesystem.
538 options MD_ROOT_SIZE=10
540 # Make the md device a potential root device, either with preloaded
541 # images of type mfs_root or md_root.
544 # Specify double the default maximum size for malloc(9)-backed md devices.
545 options MD_NSECT=40000
547 # Allow this many swap-devices.
549 # In order to manage swap, the system must reserve bitmap space that
550 # scales with the largest mounted swap device multiplied by NSWAPDEV,
551 # regardless of whether other swap devices exist or not. So it
552 # is not a good idea to make this value too large.
555 # Disk quotas are supported when this option is enabled.
556 options QUOTA #enable disk quotas
558 # If you are running a machine just as a fileserver for PC and MAC
559 # users, e.g. using SAMBA, you may consider setting this option
560 # and keeping all those users' directories on a filesystem that is
561 # mounted with the suiddir option. This gives new files the same
562 # ownership as the directory (similar to group). It's a security hole
563 # if you let these users run programs, so confine it to file-servers
564 # (but it'll save you lots of headaches in those cases). Root owned
565 # directories are exempt and X bits are cleared. The suid bit must be
566 # set on the directory as well; see chmod(1) PC owners can't see/set
567 # ownerships so they keep getting their toes trodden on. This saves
568 # you all the support calls as the filesystem it's used on will act as
569 # they expect: "It's my dir so it must be my file".
574 options NFS_MINATTRTIMO=3 # VREG attrib cache timeout in sec
575 options NFS_MAXATTRTIMO=60
576 options NFS_MINDIRATTRTIMO=30 # VDIR attrib cache timeout in sec
577 options NFS_MAXDIRATTRTIMO=60
578 options NFS_GATHERDELAY=10 # Default write gather delay (msec)
579 options NFS_UIDHASHSIZ=29 # Tune the size of nfssvc_sock with this
580 options NFS_WDELAYHASHSIZ=16 # and with this
581 options NFS_MUIDHASHSIZ=63 # Tune the size of nfsmount with this
582 options NFS_DEBUG # Enable NFS Debugging
588 options MSDOSFS_DEBUG # Enable MSDOSFS Debugging
591 # Add support for the EXT2FS filesystem of Linux fame. Be a bit
592 # careful with this - the ext2fs code has a tendency to lag behind
593 # changes and not be exercised very much, so mounting read/write could
594 # be dangerous (and even mounting read only could result in panics.)
598 # Optional character code conversion support with LIBICONV.
599 # Each option requires their base file system and LIBICONV.
601 options MSDOSFS_ICONV
604 #####################################################################
607 # Real time extensions added in the 1993 Posix
608 # _KPOSIX_PRIORITY_SCHEDULING: Build in _POSIX_PRIORITY_SCHEDULING
610 options _KPOSIX_PRIORITY_SCHEDULING
612 #####################################################################
615 # The granularity of operation is controlled by the kernel option HZ whose
616 # default value (100) means a granularity of 10ms (1s/HZ).
617 # Consider, however, that reducing the granularity too much might
618 # cause excessive overhead in clock interrupt processing,
619 # potentially causing ticks to be missed and thus actually reducing
620 # the accuracy of operation.
624 # The following options are used for debugging clock behavior only, and
625 # should not be used for production systems.
627 # CLK_CALIBRATION_LOOP will run the clock calibration loop at startup
628 # until the user presses a key.
630 #options CLK_CALIBRATION_LOOP
632 # The following two options measure the frequency of the corresponding
633 # clock relative to the RTC (onboard mc146818a).
635 #options CLK_USE_I8254_CALIBRATION
636 #options CLK_USE_TSC_CALIBRATION
638 #####################################################################
641 # SCSI DEVICE CONFIGURATION
643 # The SCSI subsystem consists of the `base' SCSI code, a number of
644 # high-level SCSI device `type' drivers, and the low-level host-adapter
645 # device drivers. The host adapters are listed in the ISA and PCI
646 # device configuration sections below.
648 # Beginning with FreeBSD 2.0.5 you can wire down your SCSI devices so
649 # that a given bus, target, and LUN always come on line as the same
650 # device unit. In earlier versions the unit numbers were assigned
651 # in the order that the devices were probed on the SCSI bus. This
652 # means that if you removed a disk drive, you may have had to rewrite
653 # your /etc/fstab file, and also that you had to be careful when adding
654 # a new disk as it may have been probed earlier and moved your device
655 # configuration around.
657 # This old behavior is maintained as the default behavior. The unit
658 # assignment begins with the first non-wired down unit for a device
659 # type. For example, if you wire a disk as "da3" then the first
660 # non-wired disk will be assigned da4.
662 # The syntax for wiring down devices is:
664 # device scbus0 at ahc0 # Single bus device
665 # device scbus1 at ahc1 bus 0 # Single bus device
666 # device scbus3 at ahc2 bus 0 # Twin bus device
667 # device scbus2 at ahc2 bus 1 # Twin bus device
668 # device da0 at scbus0 target 0 unit 0
669 # device da1 at scbus3 target 1
670 # device da2 at scbus2 target 3
671 # device sa1 at scbus1 target 6
674 # "units" (SCSI logical unit number) that are not specified are
675 # treated as if specified as LUN 0.
677 # All SCSI devices allocate as many units as are required.
679 # The "unknown" device (uk? in pre-2.0.5) is now part of the base SCSI
680 # configuration and doesn't have to be explicitly configured.
682 device scbus #base SCSI code
683 device ch #SCSI media changers
684 device da #SCSI direct access devices (aka disks)
685 device sa #SCSI tapes
686 device cd #SCSI CD-ROMs
687 device pass #CAM passthrough driver
688 device sg #Passthrough device (linux scsi generic)
689 device pt #SCSI processor type
690 device ses #SCSI SES/SAF-TE driver
691 device targ #SCSI Target Mode Code
692 device targbh #SCSI Target Mode Blackhole Device
694 # Options for device mapper
696 device dm_target_crypt
697 device dm_target_linear
698 device dm_target_striped
699 device dm_target_delay
700 device dm_target_flakey
703 device iscsi_initiator
704 options ISCSI_INITIATOR_DEBUG=8
708 # -- NOTE -- If you specify one of the bus/target/lun options, you must
710 # CAMDEBUG: When defined enables debugging macros
711 # CAM_DEBUG_BUS: Debug the given bus. Use -1 to debug all busses.
712 # CAM_DEBUG_TARGET: Debug the given target. Use -1 to debug all targets.
713 # CAM_DEBUG_LUN: Debug the given lun. Use -1 to debug all luns.
714 # CAM_DEBUG_FLAGS: OR together CAM_DEBUG_INFO, CAM_DEBUG_TRACE,
715 # CAM_DEBUG_SUBTRACE, and CAM_DEBUG_CDB
717 # CAM_MAX_HIGHPOWER: Maximum number of concurrent high power (start unit) cmds
718 # SCSI_NO_SENSE_STRINGS: When defined disables sense descriptions
719 # SCSI_NO_OP_STRINGS: When defined disables opcode descriptions
720 # SCSI_DELAY: The number of MILLISECONDS to freeze the SIM (scsi adapter)
721 # queue after a bus reset, and the number of milliseconds to
722 # freeze the device queue after a bus device reset. This
723 # can be changed at boot and runtime with the
724 # kern.cam.scsi_delay tunable/sysctl.
726 options CAM_DEBUG_BUS=-1
727 options CAM_DEBUG_TARGET=-1
728 options CAM_DEBUG_LUN=-1
729 options CAM_DEBUG_FLAGS="CAM_DEBUG_INFO|CAM_DEBUG_TRACE|CAM_DEBUG_CDB"
730 options CAM_MAX_HIGHPOWER=4
731 options SCSI_NO_SENSE_STRINGS
732 options SCSI_NO_OP_STRINGS
733 options SCSI_DELAY=8000 # Be pessimistic about Joe SCSI device
735 # Options for the CAM CDROM driver:
736 # CHANGER_MIN_BUSY_SECONDS: Guaranteed minimum time quantum for a changer LUN
737 # CHANGER_MAX_BUSY_SECONDS: Maximum time quantum per changer LUN, only
738 # enforced if there is I/O waiting for another LUN
739 # The compiled in defaults for these variables are 2 and 10 seconds,
742 # These can also be changed on the fly with the following sysctl variables:
743 # kern.cam.cd.changer.min_busy_seconds
744 # kern.cam.cd.changer.max_busy_seconds
746 options CHANGER_MIN_BUSY_SECONDS=2
747 options CHANGER_MAX_BUSY_SECONDS=10
749 # Options for the CAM sequential access driver:
750 # SA_IO_TIMEOUT: Timeout for read/write/wfm operations, in minutes
751 # SA_SPACE_TIMEOUT: Timeout for space operations, in minutes
752 # SA_REWIND_TIMEOUT: Timeout for rewind operations, in minutes
753 # SA_ERASE_TIMEOUT: Timeout for erase operations, in minutes
754 # SA_1FM_AT_EOD: Default to model which only has a default one filemark at EOT.
755 options SA_IO_TIMEOUT="(4)"
756 options SA_SPACE_TIMEOUT="(60)"
757 options SA_REWIND_TIMEOUT="(2*60)"
758 options SA_ERASE_TIMEOUT="(4*60)"
759 options SA_1FM_AT_EOD
761 # Optional timeout for the CAM processor target (pt) device
762 # This is specified in seconds. The default is 60 seconds.
763 options SCSI_PT_DEFAULT_TIMEOUT="60"
765 # Optional enable of doing SES passthrough on other devices (e.g., disks)
767 # Normally disabled because a lot of newer SCSI disks report themselves
768 # as having SES capabilities, but this can then clot up attempts to build
769 # build a topology with the SES device that's on the box these drives
771 options SES_ENABLE_PASSTHROUGH
773 #####################################################################
774 # MISCELLANEOUS DEVICES AND OPTIONS
776 # The `pty' device usually turns out to be ``effectively mandatory'',
777 # as it is required for `telnetd', `rlogind', `screen', `emacs', and
778 # `xterm', among others.
780 pseudo-device pty # Pseudo ttys
781 pseudo-device gzip # Exec gzipped a.out's
782 pseudo-device md # Memory/malloc disk
783 pseudo-device vn # File image "disks"
784 pseudo-device putter # for puffs and pud
785 pseudo-device snp # Snoop device - to look at pty/vty/etc..
786 pseudo-device ccd 4 # Concatenated disk driver
788 # Configuring Vinum into the kernel is not necessary, since the kld
789 # module gets started automatically when vinum(8) starts. This
790 # device is also untested. Use at your own risk.
792 # The option VINUMDEBUG must match the value set in CFLAGS
793 # in src/sbin/vinum/Makefile. Failure to do so will result in
794 # the following message from vinum(8):
796 # Can't get vinum config: Invalid argument
798 # see vinum(4) for more reasons not to use these options.
799 pseudo-device vinum #Vinum concat/mirror/raid driver
800 options VINUMDEBUG #enable Vinum debugging hooks
802 # Kernel side iconv library
805 # Size of the kernel message buffer. Should be N * pagesize.
806 options MSGBUF_SIZE=40960
808 #####################################################################
809 # HARDWARE DEVICE CONFIGURATION
814 # Mandatory ISA devices: isa
821 # AUTO_EOI_1 enables the `automatic EOI' feature for the master 8259A
822 # interrupt controller. This saves about 0.7-1.25 usec for each interrupt.
823 # This option breaks suspend/resume on some portables.
825 # AUTO_EOI_2 enables the `automatic EOI' feature for the slave 8259A
826 # interrupt controller. This saves about 0.7-1.25 usec for each interrupt.
827 # Automatic EOI is documented not to work for the slave with the
828 # original i8259A, but it works for some clones and some integrated
831 # MAXMEM specifies the amount of RAM on the machine; if this is not
832 # specified, DragonFly will first read the amount of memory from the CMOS
833 # RAM, so the amount of memory will initially be limited to 64MB or 16MB
834 # depending on the BIOS. If the BIOS reports 64MB, a memory probe will
835 # then attempt to detect the installed amount of RAM. If this probe
836 # fails to detect >64MB RAM you will have to use the MAXMEM option.
837 # The amount is in kilobytes, so for a machine with 128MB of RAM, it would
838 # be 131072 (128 * 1024).
840 # BROKEN_KEYBOARD_RESET disables the use of the keyboard controller to
841 # reset the CPU for reboot. This is needed on some systems with broken
842 # keyboard controllers.
846 options MAXMEM="(128*1024)"
847 #options BROKEN_KEYBOARD_RESET
849 # Enable support for the kernel PLL to use an external PPS signal,
850 # under supervision of [x]ntpd(8)
851 # More info in ntpd documentation: http://www.eecis.udel.edu/~ntp
855 # The keyboard controller; it controls the keyboard and the PS/2 mouse.
856 device atkbdc0 at isa? port IO_KBD
859 device atkbd0 at atkbdc? irq 1
862 options ATKBD_DFLT_KEYMAP # specify the built-in keymap
863 makeoptions ATKBD_DFLT_KEYMAP="jp.106"
865 # These options are valid for other keyboard drivers as well.
866 options KBD_DISABLE_KEYMAP_LOAD # refuse to load a keymap
867 options KBD_INSTALL_CDEV # install a CDEV entry in /dev
870 # 0x01 Force detection of keyboard, else we always assume a keyboard
871 # 0x02 Don't reset keyboard, useful for some newer ThinkPads
872 # 0x03 Force detection and avoid reset, might help with certain
874 # 0x04 Old-style (XT) keyboard support, useful for older ThinkPads
877 device psm0 at atkbdc? irq 12
880 options PSM_HOOKRESUME #hook the system resume event, useful
882 options PSM_RESETAFTERSUSPEND #reset the device at the resume event
884 device kbdmux # keyboard multiplexer
886 # The video card driver.
890 options VGA_DEBUG=2 # enable VGA debug output
892 # If you experience problems switching back to 80x25 (or a derived mode),
893 # the following option might help.
894 #options VGA_KEEP_POWERON_MODE # use power-on settings for 80x25
896 # If you can dispense with some vga driver features, you may want to
897 # use the following options to save some memory.
898 #options VGA_NO_FONT_LOADING # don't save/load font
899 #options VGA_NO_MODE_CHANGE # don't change video modes
901 # The following option probably won't work with the LCD displays.
902 options VGA_WIDTH90 # support 90 column modes
904 # Splash screen at start up! Screen savers require this too.
907 # The syscons console driver (sco color console compatible).
909 options MAXCONS=16 # number of virtual consoles
910 options SC_ALT_MOUSE_IMAGE # simplified mouse cursor in text mode
911 options SC_DEBUG_LEVEL=5 # enable debug output
912 options SC_DFLT_FONT # compile font in
913 makeoptions SC_DFLT_FONT=cp850
914 options SC_DISABLE_DDBKEY # disable `debug' key
915 options SC_DISABLE_REBOOT # disable reboot key sequence
916 options SC_HISTORY_SIZE=200 # number of history buffer lines
917 options SC_MOUSE_CHAR=0x3 # char code for text mode mouse cursor
918 options SC_PIXEL_MODE # add support for the raster text mode
920 # The following options will let you change the default colors of syscons.
921 options SC_NORM_ATTR="(FG_GREEN|BG_BLACK)"
922 options SC_NORM_REV_ATTR="(FG_YELLOW|BG_GREEN)"
923 options SC_KERNEL_CONS_ATTR="(FG_RED|BG_BLACK)"
924 options SC_KERNEL_CONS_REV_ATTR="(FG_BLACK|BG_RED)"
926 # If you have a two button mouse, you may want to add the following option
927 # to use the right button of the mouse to paste text.
928 options SC_TWOBUTTON_MOUSE
930 # You can selectively disable features in syscons.
931 #options SC_NO_CUTPASTE
932 #options SC_NO_FONT_LOADING
933 #options SC_NO_HISTORY
934 #options SC_NO_SYSMOUSE
939 # adv: All Narrow SCSI bus AdvanSys controllers.
940 # adw: Second Generation AdvanSys controllers including the ADV940UW.
941 # ahc: Adaptec 274x/284x/294x
943 # bt: Most Buslogic controllers
944 # ncv: NCR 53C500 based SCSI host adapters.
945 # nsp: Workbit Ninja SCSI-3 based PC Card SCSI host adapters.
946 # stg: TMC 18C30, 18C50 based PC Card SCSI host adapters.
948 # Note that the order is important in order for Buslogic cards to be
961 # Adaptec FSA RAID controllers, including integrated DELL controller,
962 # the Dell PERC 2/QC and the HP NetRAID-4M
966 device aacp # SCSI Passthrough interface (optional, CAM required)
969 # Compaq Smart RAID, Mylex DAC960 and AMI MegaRAID controllers. Only
970 # one entry is needed; the code will find and configure all supported
973 device ida # Compaq Smart RAID
974 device mlx # Mylex DAC960
975 device amr # AMI MegaRAID
976 device amrp # SCSI Passthrough interface (optional, CAM req.)
978 device mfi # LSI MegaRAID SAS
979 device mfip # LSI MegaRAID SAS passthrough, requires CAM
983 # LSI MegaRAID 6Gb/s and 12Gb/s SAS+SATA RAID controller driver
988 # Areca RAID (CAM is required).
990 device arcmsr # Areca SATA II RAID
993 # Highpoint RocketRAID 182x.
997 # Highpoint RocketRAID. Supports RR172x, RR222x, RR2240, RR232x, RR2340,
998 # RR2210, RR174x, RR2522, RR231x, RR230x.
1002 # Highpoint RocketRAID 27xx.
1006 # Highpoint RocketRaid 3xxx series SATA RAID
1012 device twe # 3ware ATA RAID
1013 device twa # 3ware 9000 series PATA/SATA RAID
1014 options TWA_DEBUG=10 # enable debug messages
1015 device tws # 3ware 9750 series SATA/SAS RAID
1022 # AHCI driver, this will override NATA for AHCI devices,
1023 # both drivers may be included.
1027 # SiI3124/3132 driver
1031 # The 'NATA' driver supports all ATA and ATAPI devices.
1032 # You only need one "device nata" for it to find all
1033 # PCI ATA/ATAPI devices on modern machines.
1036 device natadisk # ATA disk drives
1037 device natapicd # ATAPI CD/DVD drives
1038 device natapifd # ATAPI floppy drives
1039 device natapist # ATAPI tape drives
1040 device natapicam # ATAPI CAM layer emulation
1041 device nataraid # support for ATA software RAID controllers
1043 # The following options are valid for the NATA driver:
1045 # ATA_STATIC_ID: controller numbering is static (like the old driver)
1046 # else the device numbers are dynamically allocated.
1047 options ATA_STATIC_ID
1049 # For older non-PCI systems, these are the lines to use:
1051 #device nata0 at isa? port IO_WD1 irq 14
1052 #device nata1 at isa? port IO_WD2 irq 15
1055 # Standard floppy disk controllers: `fdc' and `fd'
1057 #device fdc0 at isa? port IO_FD1 irq 6 drq 2
1059 # FDC_DEBUG enables floppy debugging. Since the debug output is huge, you
1060 # gotta turn it actually on by setting the variable fd_debug with DDB,
1064 #device fd0 at fdc0 drive 0
1065 #device fd1 at fdc0 drive 1
1068 # sio: serial ports (see sio(4))
1070 device sio0 at isa? port IO_COM1 flags 0x10 irq 4
1073 # `flags' for serial drivers that support consoles (only for sio now):
1074 # 0x10 enable console support for this unit. The other console flags
1075 # are ignored unless this is set. Enabling console support does
1076 # not make the unit the preferred console - boot with -h or set
1077 # the 0x20 flag for that. Currently, at most one unit can have
1078 # console support; the first one (in config file order) with
1079 # this flag set is preferred. Setting this flag for sio0 gives
1080 # the old behaviour.
1081 # 0x20 force this unit to be the console (unless there is another
1082 # higher priority console). This replaces the COMCONSOLE option.
1083 # 0x40 reserve this unit for low level console operations. Do not
1084 # access the device in any normal way.
1085 # 0x80 use this port for serial line gdb support in ddb.
1088 # Options for serial drivers that support consoles (only for sio now):
1089 options BREAK_TO_DEBUGGER #a BREAK on a comconsole goes to
1091 options CONSPEED=115200 # speed for serial console
1094 # Solaris implements a new BREAK which is initiated by a character
1095 # sequence CR ~ ^b which is similar to a familiar pattern used on
1096 # Sun servers by the Remote Console.
1097 options ALT_BREAK_TO_DEBUGGER
1100 options COM_ESP #code for Hayes ESP
1101 options COM_MULTIPORT #code for some cards with shared IRQs
1103 # Other flags for sio that aren't documented in the man page.
1104 # 0x20000 enable hardware RTS/CTS and larger FIFOs. Only works for
1105 # ST16650A-compatible UARTs.
1107 # PCI Universal Communications driver
1108 # Supports various single and multi port PCI serial cards. Maybe later
1109 # also the parallel ports on combination serial/parallel cards. New cards
1110 # can be added in src/sys/dev/misc/puc/pucdata.c.
1114 # Network interfaces: `ed', `ep', `is', `lnc'
1116 # cs: IBM Etherjet and other Crystal Semi CS89x0-based adapters
1118 # ex: Intel EtherExpress Pro/10 and other i82595-based adapters
1119 # lnc: Lance/PCnet cards (Isolan, Novell NE2100, NE32-VL, AMD Am7990 & Am79C960)
1120 # sbsh: Granch SBNI16 SHDSL modem PCI adapters
1121 # wi: Lucent WaveLAN/IEEE 802.11 PCMCIA adapters. Note: this supports both
1122 # the PCMCIA and ISA cards: the ISA card is really a PCMCIA to ISA
1123 # bridge with a PCMCIA adapter plugged into it.
1124 # xe: Xircom/Intel EtherExpress Pro100/16 PC Card ethernet controller.
1133 # Wlan support is mandatory for some wireless LAN devices.
1134 options IEEE80211_DEBUG #enable debugging msgs
1135 options IEEE80211_SUPPORT_MESH #enable 802.11s D3.0 support
1136 options IEEE80211_SUPPORT_TDMA #enable TDMA support
1137 device wlan # 802.11 support
1138 device wlan_acl # 802.11 MAC-based access control for AP
1139 device wlan_ccmp # 802.11 CCMP support
1140 device wlan_tkip # 802.11 TKIP support
1141 device wlan_wep # 802.11 WEP support
1142 device wlan_xauth # 802.11 WPA or 802.1x authentication for AP
1143 device wlan_amrr # 802.11 AMRR TX rate control algorithm
1144 device ath # Atheros AR521x
1145 options AH_AR5416_INTERRUPT_MITIGATION
1148 options AH_INTERRUPT_DEBUGGING
1149 options AH_MAXCHAN=96
1150 options AH_NEED_DESC_SWAP
1151 options AH_PRIVATE_DIAG
1152 options AH_RXCFG_SDMAMW_4BYTES
1153 options AH_SUPPORT_AR5416
1154 options AH_SUPPORT_AR9130
1155 options AH_SUPPORT_AR9330
1156 options AH_SUPPORT_AR9340
1157 options AH_USE_INIPDGAIN
1158 device ath_hal # Atheros Hardware Access Layer
1159 #device ath_rate_amrr # Atheros AMRR TX rate control algorithm
1160 #device ath_rate_onoe # Atheros Onoe TX rate control algorithm
1161 device ath_rate_sample # Atheros Sample TX rate control algorithm
1162 options ATH_DEBUG # turn on debugging output (see hw.ath.debug)
1163 options ATH_DIAGAPI # diagnostic interface to the HAL
1164 options ATH_ENABLE_DFS
1165 options ATH_KTR_INTR_DEBUG
1166 device siba_bwn # Sonic Inc. Silicon Backplane needed for bwn
1167 options SIBA_DEBUG # turn on debugging output
1168 device bwn # Broadcom BCM43xx NICs using v4 firmware
1169 options BWN_DEBUG # turn on debugging output
1170 options BWN_RXRING_SLOTS=128 # number of RX slots to allocate
1171 options BWN_TXRING_SLOTS=128 # number of TX slots to allocate
1172 device iwi # Intel PRO/Wireless 2200BG/2915ABG
1173 device iwm # Intel Dual Band Wireless AC 3160/3165/7260/7265/8260
1174 options IWM_DEBUG # turn on debugging output
1175 device iwn # Intel WiFi Link 4965/1000/5000/5150/5300/6000/6050
1176 options IWN_DEBUG # turn on debugging output
1177 device wi # WaveLAN/IEEE, PRISM-II, Spectrum24 802.11DS
1178 device xe # Xircom PCMCIA
1179 device ral # Ralink Technology 802.11 wireless NIC
1181 options WPI_DEBUG # turn on debugging output
1183 # IEEE 802.11 adapter firmware modules
1185 # iwifw: Intel PRO/Wireless 2200BG/2225BG/2915ABG firmware
1186 # iwmfw Intel Dual Band Wireless AC 3160/3165/7260/7265/8260
1187 # iwnfw: Intel WiFi Link 4965/1000/5000/5150/5300/6000/6050
1188 # ralfw: Ralink Technology RT25xx and RT26xx firmware
1189 # wpifw: Intel 3945ABG Wireless LAN Controller firmware
1197 # Bluetooth Protocols
1203 # Basic sound card support:
1205 # For PCI sound cards:
1206 device "snd_als4000"
1210 device "snd_emu10k1"
1211 device "snd_emu10kx"
1213 device "snd_envy24ht"
1219 device "snd_maestro"
1220 device "snd_neomagic"
1223 device "snd_t4dwave"
1224 device "snd_via8233"
1225 device "snd_via82c686"
1231 # Following options are intended for debugging/testing purposes:
1233 # SND_DEBUG Enable extra debugging code that includes
1234 # sanity checking and possible increase of
1237 # SND_DIAGNOSTIC Similar in a spirit of INVARIANTS/DIAGNOSTIC,
1238 # zero tolerance against inconsistencies.
1240 # SND_FEEDER_MULTIFORMAT By default, only 16/32 bit feeders are compiled
1241 # in. This options enable most feeder converters
1242 # except for 8bit. WARNING: May bloat the kernel.
1244 # SND_FEEDER_FULL_MULTIFORMAT Ditto, but includes 8bit feeders as well.
1246 # SND_FEEDER_RATE_HP (feeder_rate) High precision 64bit arithmetic
1247 # as much as possible (the default trying to
1248 # avoid it). Possible slowdown.
1250 # SND_PCM_64 (Only applicable for i386/32bit arch)
1251 # Process 32bit samples through 64bit
1252 # integer/arithmetic. Slight increase of dynamic
1253 # range at a cost of possible slowdown.
1255 # SND_OLDSTEREO Only 2 channels are allowed, effectively
1256 # disabling multichannel processing.
1259 #options SND_DIAGNOSTIC
1260 options SND_FEEDER_MULTIFORMAT
1261 options SND_FEEDER_FULL_MULTIFORMAT
1262 options SND_FEEDER_RATE_HP
1264 options SND_OLDSTEREO
1267 # Miscellaneous hardware:
1269 # bktr: Brooktree bt848/848a/849a/878/879 video capture and TV Tuner board
1270 # coremctl: Intel Core/E3 memory controller (required by ecc(4) and memtemp(4))
1271 # dimm: Location inforamtion (required by ecc(4) and memtemp(4))
1272 # ecc: ECC memory controller
1273 # ipmi: Intelligent Platform Management Interface
1275 # nrp: Comtrol Rocketport
1276 # si: Specialix SI/XIO 4-32 port terminal multiplexor
1277 # nmdm: nullmodem terminal driver (see nmdm(4))
1278 # tpm: Trusted Platform Module
1280 # Notes on the Specialix SI/XIO driver:
1281 # **This is NOT a Specialix supported Driver!**
1282 # The host card is memory, not IO mapped.
1283 # The Rev 1 host cards use a 64K chunk, on a 32K boundary.
1284 # The Rev 2 host cards use a 32K chunk, on a 32K boundary.
1285 # The cards can use an IRQ of 11, 12 or 15.
1290 device joy0 at isa? port IO_GAME
1293 # nullmodem terminal driver
1298 # The `ahc' device provides support for the Adaptec 274X and 284X
1302 # The aic7xxx driver will attempt to use memory mapped I/O for all PCI
1303 # controllers that have it configured only if this option is set. Unfortunately,
1304 # this doesn't work on some motherboards, which prevents it from being the
1306 options AHC_ALLOW_MEMIO
1308 # The adw driver will attempt to use memory mapped I/O for all PCI
1309 # controllers that have it configured only if this option is set.
1310 options ADW_ALLOW_MEMIO
1313 # PCI devices & PCI options:
1315 # The main PCI bus device is `pci'. It provides auto-detection and
1316 # configuration support for all devices on the PCI bus, using either
1317 # configuration mode defined in the PCI specification.
1330 # The `ahc' device provides support for the Adaptec 29/3940(U)(W)
1331 # and motherboard based AIC7870/AIC7880 adapters.
1333 options AHC_DEBUG_OPTS=0xffffffff
1334 options AHC_REG_PRETTY_PRINT
1335 options AHC_TMODE_ENABLE
1337 # The 'ahd' device provides support for the Adaptec 79xx Ultra320
1338 # SCSI adapters. Options are documented in the ahd(4) manpage:
1340 options AHD_DEBUG_OPTS=0xffffffff
1341 options AHD_REG_PRETTY_PRINT
1342 #options AHD_TMODE_ENABLE=0xff
1344 # The `amd' device provides support for the AMD 53C974 SCSI host
1345 # adapter chip as found on devices such as the Tekram DC-390(T).
1347 # The `bge' device provides support for gigabit ethernet adapters
1348 # based on the Broadcom BCM570x family of controllers, including the
1349 # 3Com 3c996-T, the Netgear GA302T, the SysKonnect SK-9D21 and SK-9D41,
1350 # and the embedded gigE NICs on Dell PowerEdge 2550 servers.
1352 # The `ncr' device provides support for the NCR 53C810 and 53C825
1353 # self-contained SCSI host adapters.
1355 # The `isp' device provides support for the Qlogic ISP 1020, 1040
1356 # nd 1040B PCI SCSI host adapters, ISP 1240 Dual Ultra SCSI,
1357 # ISP 1080 and 1280 (Dual) Ultra2, ISP 12160 Ultra3 SCSI, as well as
1358 # the Qlogic ISP 2100 and ISP 2200 Fibre Channel Host Adapters.
1360 # The `dc' device provides support for PCI fast ethernet adapters
1361 # based on the DEC/Intel 21143 and various workalikes including:
1362 # the ADMtek AL981 Comet and AN985 Centaur, the ASIX Electronics
1363 # AX88140A and AX88141, the Davicom DM9100 and DM9102, the Lite-On
1364 # 82c168 and 82c169 PNIC, the Lite-On/Macronix LC82C115 PNIC II
1365 # and the Macronix 98713/98713A/98715/98715A/98725 PMAC. This driver
1366 # replaces the old al, ax, dm, pn and mx drivers. List of brands:
1367 # Digital DE500-BA, Kingston KNE100TX, D-Link DFE-570TX, SOHOware SFA110,
1368 # SVEC PN102-TX, CNet Pro110B, 120A, and 120B, Compex RL100-TX,
1369 # LinkSys LNE100TX, LNE100TX V2.0, Jaton XpressNet, Alfa Inc GFC2204,
1372 # The `de' device provides support for the Digital Equipment DC21040
1373 # self-contained Ethernet adapter.
1375 # The `em' device provides support for the Intel Pro/1000 Family of Gigabit
1376 # adapters (82542, 82543, 82544, 82540).
1378 # The `et' device provides support for the Agere ET1310 10/100/1000 PCIe
1381 # The `fxp' device provides support for the Intel EtherExpress Pro/100B
1382 # PCI Fast Ethernet adapters.
1384 # The 'lge' device provides support for PCI gigabit ethernet adapters
1385 # based on the Level 1 LXT1001 NetCellerator chipset. This includes the
1386 # D-Link DGE-500SX, SMC TigerCard 1000 (SMC9462SX), and some Addtron cards.
1388 # The 'my' device provides support for the Myson MTD80X and MTD89X PCI
1389 # Fast Ethernet adapters.
1391 # The 'nge' device provides support for PCI gigabit ethernet adapters
1392 # based on the National Semiconductor DP83820 and DP83821 chipset. This
1393 # includes the SMC EZ Card 1000 (SMC9462TX), D-Link DGE-500T, Asante
1394 # FriendlyNet GigaNIX 1000TA and 1000TPC, the Addtron AEG320T, the
1395 # LinkSys EG1032 and EG1064, the Surecom EP-320G-TX and the Netgear GA622T.
1397 # The 'oce' device provides support for Emulex 10 Gbit adapters
1398 # (OneConnect Ethernet).
1400 # The 'pcn' device provides support for PCI fast ethernet adapters based
1401 # on the AMD Am79c97x chipsets, including the PCnet/FAST, PCnet/FAST+,
1402 # PCnet/PRO and PCnet/Home. These were previously handled by the lnc
1403 # driver (and still will be if you leave this driver out of the kernel).
1405 # Te 're' device provides support for PCI GigaBit ethernet adapters based
1406 # on the RealTek 8169 chipset. It also supports the 8139C+ and is the
1407 # preferred driver for that chip.
1409 # The 'rl' device provides support for PCI fast ethernet adapters based
1410 # on the RealTek 8129/8139 chipset. Note that the RealTek driver defaults
1411 # to using programmed I/O to do register accesses because memory mapped
1412 # mode seems to cause severe lockups on SMP hardware. This driver also
1413 # supports the Accton EN1207D `Cheetah' adapter, which uses a chip called
1414 # the MPX 5030/5038, which is either a RealTek in disguise or a RealTek
1415 # workalike. Note that the D-Link DFE-530TX+ uses the RealTek chipset
1416 # and is supported by this driver, not the 'vr' driver.
1418 # The 'sf' device provides support for Adaptec Duralink PCI fast
1419 # ethernet adapters based on the Adaptec AIC-6915 "starfire" controller.
1420 # This includes dual and quad port cards, as well as one 100baseFX card.
1421 # Most of these are 64-bit PCI devices, except for one single port
1422 # card which is 32-bit.
1424 # The 'ste' device provides support for adapters based on the Sundance
1425 # Technologies ST201 PCI fast ethernet controller. This includes the
1428 # The 'sis' device provides support for adapters based on the Silicon
1429 # Integrated Systems SiS 900 and SiS 7016 PCI fast ethernet controller
1432 # The 'sk' device provides support for the SysKonnect SK-984x series
1433 # PCI gigabit ethernet NICs. This includes the SK-9841 and SK-9842
1434 # single port cards (single mode and multimode fiber) and the
1435 # SK-9843 and SK-9844 dual port cards (also single mode and multimode).
1436 # The driver will autodetect the number of ports on the card and
1437 # attach each one as a separate network interface.
1439 # The 'ti' device provides support for PCI gigabit ethernet NICs based
1440 # on the Alteon Networks Tigon 1 and Tigon 2 chipsets. This includes the
1441 # Alteon AceNIC, the 3Com 3c985, the Netgear GA620 and various others.
1442 # Note that you will probably want to bump up NMBCLUSTERS a lot to use
1445 # The 'tl' device provides support for the Texas Instruments TNETE100
1446 # series 'ThunderLAN' cards and integrated ethernet controllers. This
1447 # includes several Compaq Netelligent 10/100 cards and the built-in
1448 # ethernet controllers in several Compaq Prosignia, Proliant and
1449 # Deskpro systems. It also supports several Olicom 10Mbps and 10/100
1452 # The `tx' device provides support for the SMC 9432 TX, BTX and FTX cards.
1454 # The `txp' device provides support for the 3Com 3cR990 "Typhoon"
1457 # The `vr' device provides support for various fast ethernet adapters
1458 # based on the VIA Technologies VT3043 `Rhine I' and VT86C100A `Rhine II'
1459 # chips, including the D-Link DFE530TX (see 'rl' for DFE530TX+), the Hawking
1460 # Technologies PN102TX, and the AOpen/Acer ALN-320.
1462 # The `vx' device provides support for the 3Com 3C590 and 3C595
1465 # The `wb' device provides support for various fast ethernet adapters
1466 # based on the Winbond W89C840F chip. Note: this is not the same as
1467 # the Winbond W89C940F, which is an NE2000 clone.
1469 # The `xl' device provides support for the 3Com 3c900, 3c905 and
1470 # 3c905B (Fast) Etherlink XL cards and integrated controllers. This
1471 # includes the integrated 3c905B-TX chips in certain Dell Optiplex and
1472 # Dell Precision desktop machines and the integrated 3c905-TX chips
1473 # in Dell Latitude laptop docking stations.
1475 # The 'bktr' device is a PCI video capture device using the Brooktree
1476 # bt848/bt848a/bt849a/bt878/bt879 chipset. When used with a TV Tuner it forms a
1477 # TV card, eg Miro PC/TV, Hauppauge WinCast/TV WinTV, VideoLogic Captivator,
1478 # Intel Smart Video III, AverMedia, IMS Turbo, FlyVideo.
1480 # options OVERRIDE_CARD=xxx
1481 # options OVERRIDE_TUNER=xxx
1482 # options OVERRIDE_MSP=1
1483 # options OVERRIDE_DBX=1
1484 # These options can be used to override the auto detection
1485 # The current values for xxx are found in src/sys/dev/video/bktr/bktr_card.h
1486 # Using sysctl(8) run-time overrides on a per-card basis can be made
1488 # options BKTR_SYSTEM_DEFAULT=BROOKTREE_PAL
1490 # options BKTR_SYSTEM_DEFAULT=BROOKTREE_NTSC
1491 # Specifies the default video capture mode.
1492 # This is required for Dual Crystal (28&35Mhz) boards where PAL is used
1493 # to prevent hangs during initialisation. eg VideoLogic Captivator PCI.
1495 # options BKTR_USE_PLL
1496 # PAL or SECAM users who have a 28Mhz crystal (and no 35Mhz crystal)
1497 # must enable PLL mode with this option. eg some new Bt878 cards.
1499 # options BKTR_GPIO_ACCESS
1500 # This enable IOCTLs which give user level access to the GPIO port.
1502 # options BKTR_NO_MSP_RESET
1503 # Prevents the MSP34xx reset. Good if you initialise the MSP in another OS first
1505 # options BKTR_430_FX_MODE
1506 # Switch Bt878/879 cards into Intel 430FX chipset compatibility mode.
1508 # options BKTR_SIS_VIA_MODE
1509 # Switch Bt878/879 cards into SIS/VIA chipset compatibility mode which is
1510 # needed for some old SiS and VIA chipset motherboards.
1511 # This also allows Bt878/879 chips to work on old OPTi (<1997) chipset
1512 # motherboards and motherboards with bad or incomplete PCI 2.1 support.
1513 # As a rough guess, old = before 1998
1515 # options BKTR_NEW_MSP34XX_DRIVER
1516 # Use new, more complete initialization scheme for the msp34* soundchip.
1517 # Should fix stereo autodetection if the old driver does only output
1520 # options BKTR_OVERRIDE_CARD=xxx
1521 # options BKTR_OVERRIDE_DBX=xxx
1522 # options BKTR_OVERRIDE_MSP=xxx
1523 # options BKTR_OVERRIDE_TUNER=xxx
1524 # These options can be used to select a specific device, regardless of
1525 # the autodetection and i2c device checks (see comments in bktr_card.c).
1527 device ahc # AHA2940 and onboard AIC7xxx devices
1528 device ahd # AIC79xx devices
1529 device amd # AMD 53C974 (Tekram DC-390(T))
1530 device isp # Qlogic family
1531 device ispfw # Firmware for QLogic HBAs
1532 device mpt # LSI '909 FC adapters
1533 device mps # LSI-Logic MPT-Fusion 2
1534 device ncr # NCR/Symbios Logic
1535 device sym # NCR/Symbios Logic (newer chipsets)
1536 device trm # Tekram DC395U/UW/F and DC315U
1540 # ISP_TARGET_MODE - enable target mode operation
1541 #options ISP_TARGET_MODE=1
1543 # Options used in dev/disk/sym/ (Symbios SCSI driver).
1544 #options SYM_SETUP_LP_PROBE_MAP #-Low Priority Probe Map (bits)
1545 # Allows the ncr to take precedence
1546 # 1 (1<<0) -> 810a, 860
1547 # 2 (1<<1) -> 825a, 875, 885, 895
1548 # 4 (1<<2) -> 895a, 896, 1510d
1549 #options SYM_SETUP_SCSI_DIFF #-HVD support for 825a, 875, 885
1550 # disabled:0 (default), enabled:1
1551 #options SYM_SETUP_PCI_PARITY #-PCI parity checking
1552 # disabled:0, enabled:1 (default)
1553 #options SYM_SETUP_MAX_LUN #-Number of LUNs supported
1554 # default:8, range:[1..64]
1557 # MII bus support is required for some PCI 10/100 ethernet NICs,
1558 # namely those which use MII-compliant transceivers or implement
1559 # transceiver control interfaces that operate like an MII. Adding
1560 # "device miibus0" to the kernel config pulls in support for
1561 # the generic miibus API and all of the PHY drivers, including a
1562 # generic one for PHYs that aren't specifically handled by an
1563 # individual driver.
1566 # PCI Ethernet NICs that use the common MII bus controller code.
1567 device ae # Attansic/Atheros L2 Fast Ethernet
1568 device alc # Atheros AR8131/AR8132
1569 device ale # Atheros AR8121/AR8113/AR8114
1570 device age # Attansic/Atheros L1 Gigabit Ethernet
1571 device bce # Broadcom NetXtreme II Gigabit Ethernet
1572 device bfe # Broadcom BCM440x 10/100 Ethernet
1573 device bnx # Broadcom NetXtreme 5718/57785 Gigabit Ethernet
1574 device dc # DEC/Intel 21143 and various workalikes
1575 device fxp # Intel EtherExpress PRO/100B (82557, 82558)
1576 device my # Myson Fast Ethernet (MTD80X, MTD89X)
1577 device pcn # AMD Am79C97x PCI 10/100 NICs
1578 device re # RealTek 8139C+/8169
1579 device rl # RealTek 8129/8139
1580 device sbsh # Granch SBNI16 SHDSL modem
1581 device sf # Adaptec AIC-6915 (``Starfire'')
1582 device sis # Silicon Integrated Systems SiS 900/SiS 7016
1583 device ste # Sundance ST201 (D-Link DFE-550TX)
1584 device tl # Texas Instruments ThunderLAN
1585 device tx # SMC EtherPower II (83c17x ``EPIC'')
1586 device vge # VIA 612x GigE
1587 device vr # VIA Rhine, Rhine II
1588 device wb # Winbond W89C840F
1589 device xl # 3Com 3c90x (``Boomerang'', ``Cyclone'')
1591 # PCI Ethernet NICs.
1592 device de # DEC/Intel DC21x4x (``Tulip'')
1593 device txp # 3Com 3cR990 (``Typhoon'')
1594 device vx # 3Com 3c590, 3c595 (``Vortex'')
1596 # Gigabit Ethernet NICs.
1597 device bge # Broadcom BCM570x (``Tigon III'')
1598 device em # Intel Pro/1000 (8254x,8257x)
1600 device emx # Intel Pro/1000 (8257{1,2,3,4})
1602 device igb # Intel Pro/1000 (82575, 82576, 82580, i350)
1604 device ig_hal # Intel Pro/1000 hardware abstraction layer
1605 device ix # Intel PRO/10GbE PCIE Ethernet Family
1606 device et # Agere ET1310 10/100/1000 Ethernet
1607 device lge # Level 1 LXT1001 (``Mercury'')
1608 device mxge # Myricom Myri-10G 10GbE NIC
1609 device nfe # nVidia nForce2/3 MCP04/51/55 CK804
1610 device nge # NatSemi DP83820 and DP83821
1611 device oce # Emulex 10 GbE (OneConnect Ethernet)
1612 device sk # SysKonnect GEnesis, LinkSys EG1023, D-Link
1613 device ti # Alteon (``Tigon I'', ``Tigon II'')
1614 device stge # Sundance/Tamarack TC9021 Gigabit Ethernet
1615 device msk # Marvell/SysKonnect Yukon II Gigabit Ethernet
1616 device jme # JMicron Gigabit/Fast Ethernet
1618 # Brooktree driver has been ported to the new I2C framework. Thus,
1619 # you'll need to have the following 3 lines in the kernel config.
1623 # The iic and smb devices are only needed if you want to control other
1624 # I2C slaves connected to the external connector of some cards.
1627 options BKTR_NEW_MSP34XX_DRIVER
1629 # WinTV PVR-250/350 driver
1635 # pccard: pccard slots
1636 # cardbus/cbb: cardbus bridge
1645 # mmcsd MMC/SD memory card
1646 # sdhci Generic PCI SD Host Controller
1655 # System Management Bus support is provided by the 'smbus' device.
1656 # Access to the SMBus device is via the 'smb' device (/dev/smb*),
1657 # which is a child of the 'smbus' device.
1659 # Supported devices:
1660 # smb standard io through /dev/smb*
1663 # smbacpi support for ACPI I2cSerialBus resources
1665 # Supported SMB interfaces:
1666 # iicsmb I2C to SMB bridge with any iicbus interface
1667 # bktr brooktree848 I2C hardware interface
1668 # intpm Intel PIIX4 (82371AB, 82443MX) Power Management Unit
1669 # alpm Acer Aladdin-IV/V/Pro2 Power Management Unit
1670 # ichiic Intel generation 4 I2C controller
1671 # ichsmb Intel ICH SMBus controller chips (82801AA, 82801AB, 82801BA)
1672 # viapm VIA VT82C586B,596,686A and VT8233 SMBus controllers
1673 # amdpm AMD 756 Power Management Unit
1674 # amdsmb AMD 8111 SMBus 2.0 Controller
1676 device smbus # Bus support, required for smb below.
1693 # Philips i2c bus support is provided by the `iicbus' device.
1695 # Supported devices:
1696 # ic i2c network interface
1697 # iic i2c standard io
1698 # iicsmb i2c to smb bridge. Allow i2c i/o with smb commands.
1700 # Supported interfaces:
1701 # pcf Philips PCF8584 ISA-bus controller
1702 # bktr brooktree848 I2C software interface
1705 # iicbb generic I2C bit-banging code (needed by lpbb, bktr)
1707 device iicbus # Bus support, required for ic/iic/iicsmb below.
1712 device iicsmb # smb over i2c bridge
1714 device pcf0 at isa? port 0x320 irq 5
1716 # Intel performance-energy bias
1719 # Intel software controlled clock modulation
1722 # Intel Sandy Bridge and newer CPUs power usage estimation
1725 # Intel Core and newer CPUs on-die digital thermal sensor support
1728 # Memory thermal sensor
1731 # CPU control pseudo-device. Provides access to MSRs, CPUID info and
1732 # microcode update feature.
1735 # Effective CPU frequency interface via APERF/MPERF MSRs
1738 # AMD Family 0Fh, 10h and 11h temperature sensors
1742 # ThinkPad Active Protection System accelerometer
1743 device aps0 at isa? port 0x1600
1745 # HW monitoring devices lm(4), it(4) and nsclpcsio.
1746 device lm0 at isa? port 0x290
1747 device it0 at isa? port 0x290
1748 device it1 at isa? port 0xc00
1749 device it2 at isa? port 0xd00
1750 device it3 at isa? port 0x228
1751 device nsclpcsio0 at isa? port 0x2e
1752 device nsclpcsio1 at isa? port 0x4e
1753 device wbsio0 at isa? port 0x2e
1754 device wbsio1 at isa? port 0x4e
1755 device uguru0 at isa? port 0xe0 # ABIT uGuru
1759 # Parallel port bus support is provided by the `ppbus' device.
1760 # Multiple devices may be attached to the parallel port, devices
1761 # are automatically probed and attached when found.
1763 # Supported devices:
1764 # vpo Iomega Zip Drive
1765 # Requires SCSI disk support ('scbus' and 'da'); the best
1766 # performance is achieved with ports in EPP 1.9 mode.
1767 # lpt Parallel Printer
1768 # plip Parallel network interface
1769 # ppi General-purpose I/O ("Geek Port") + IEEE1284 I/O
1770 # pps Pulse per second Timing Interface
1771 # lpbb Philips official parallel port I2C bit-banging interface
1773 # Supported interfaces:
1774 # ppc ISA-bus parallel port interfaces.
1777 options PPC_PROBE_CHIPSET # Enable chipset specific detection
1778 # (see flags in ppc(4))
1779 options DEBUG_1284 # IEEE1284 signaling protocol debug
1780 options PERIPH_1284 # Makes your computer act as a IEEE1284
1781 # compliant peripheral
1782 options DONTPROBE_1284 # Avoid boot detection of PnP parallel devices
1783 options VP0_DEBUG # ZIP/ZIP+ debug
1784 options LPT_DEBUG # Printer driver debug
1785 options PPC_DEBUG=2 # Parallel chipset level debug
1786 options PLIP_DEBUG # Parallel network IP interface debug
1787 options PCFCLOCK_VERBOSE # Verbose pcfclock driver
1788 options PCFCLOCK_MAX_RETRIES=5 # Maximum read tries (default 10)
1790 device ppc0 at isa? irq 7
1800 # Kernel BOOTP support
1802 options BOOTP # Use BOOTP to obtain IP address/hostname
1803 options BOOTP_NFSROOT # NFS mount root filesystem using BOOTP info
1804 options BOOTP_COMPAT # Workaround for broken bootp daemons.
1805 options BOOTP_WIRED_TO=fxp0 # Use interface fxp0 for BOOTP
1808 # Set the number of PV entries per process. Increasing this can
1809 # stop panics related to heavy use of shared memory. However, that can
1810 # (combined with large amounts of physical memory) cause panics at
1811 # boot time due the kernel running out of VM space.
1813 # If you're tweaking this, you might also want to increase the sysctls
1814 # "vm.v_free_min", "vm.v_free_reserved", and "vm.v_free_target".
1816 # The value below is the one more than the default.
1818 options PMAP_SHPGPERPROC=201
1821 # Disable swapping. This option removes all code which actually performs
1822 # swapping, so it's not possible to turn it back on at run-time.
1824 # This is sometimes usable for systems which don't have any swap space
1825 # (see also sysctls "vm.defer_swapspace_pageouts" and
1826 # "vm.disable_swapspace_pageouts")
1828 #options NO_SWAPPING
1830 # Set the size of the buffer cache KVM reservation, in buffers. This is
1831 # scaled by approximately 16384 bytes. The system will auto-size the buffer
1832 # cache if this option is not specified.
1836 # Set the size of the mbuf KVM reservation, in clusters. This is scaled
1837 # by approximately 2048 bytes. The system will auto-size the mbuf area
1838 # to (512 + maxusers*16) if this option is not specified.
1839 # maxusers is in turn computed at boot time depending on available memory
1840 # or set to the value specified by "options MAXUSERS=x" (x=0 means
1842 # So, to take advantage of autoscaling, you have to remove both
1843 # NMBCLUSTERS and MAXUSERS (and NMBUFS) from your kernel config.
1845 options NMBCLUSTERS=1024
1847 # Set the number of mbufs available in the system. Each mbuf
1848 # consumes 256 bytes. The system will autosize this (to 4 times
1849 # the number of NMBCLUSTERS, depending on other constraints)
1850 # if this option is not specified.
1854 # Tune the buffer cache maximum KVA reservation, in bytes. The maximum is
1855 # usually capped at 200 MB, effecting machines with > 1GB of ram. Note
1856 # that the buffer cache only really governs write buffering and disk block
1857 # translations. The VM page cache is our primary disk cache and is not
1858 # effected by the size of the buffer cache.
1860 options VM_BCACHE_SIZE_MAX="(100*1024*1024)"
1862 # Tune the swap zone KVA reservation, in bytes. The default is typically
1863 # 70 MB, giving the system the ability to manage a maximum of 28GB worth
1864 # of swapped out data.
1866 options VM_SWZONE_SIZE_MAX="(50*1024*1024)"
1869 # Enable extra debugging code for locks. This stores the filename and
1870 # line of whatever acquired the lock in the lock itself, and change a
1871 # number of function calls to pass around the relevant data. This is
1872 # not at all useful unless you are debugging lock code. Also note
1873 # that it is likely to break e.g. fstat(1) unless you recompile your
1874 # userland with -DDEBUG_LOCKS as well.
1876 # DEBUG_LOCKS_LATENCY adds a sysctl to add a forced latency loop
1877 # (count to N) in front of any spinlock or gettoken.
1880 options DEBUG_LOCKS_LATENCY
1882 # Set the amount of time (in seconds) the system will wait before
1883 # rebooting automatically when a kernel panic occurs. If set to (-1),
1884 # the system will wait indefinitely until a key is pressed on the
1886 options PANIC_REBOOT_WAIT_TIME=16
1888 # Attempt to bypass the buffer cache and put data directly into the
1889 # userland buffer for read operation when O_DIRECT flag is set on the
1890 # file. Both offset and length of the read operation must be
1891 # multiples of the physical media sector size.
1895 # Specify a lower limit for the number of swap I/O buffers. They are
1896 # (among other things) used when bypassing the buffer cache due to
1897 # DIRECTIO kernel option enabled and O_DIRECT flag set on file.
1899 #options NSWBUF_MIN=120
1901 # The 'asr' driver provides support for current DPT/Adaptec SCSI RAID
1902 # controllers (SmartRAID V and VI and later).
1903 # These controllers require the CAM infrastructure.
1907 # The 'dpt' driver provides support for DPT controllers (http://www.dpt.com/).
1908 # These have hardware RAID-{0,1,5} support, and do multi-initiator I/O.
1909 # The DPT controllers are commonly re-licensed under other brand-names -
1910 # some controllers by Olivetti, Dec, HP, AT&T, SNI, AST, Alphatronic, NEC and
1911 # Compaq are actually DPT controllers.
1913 # See src/sys/dev/raid/dpt for debugging and other subtle options.
1914 # DPT_MEASURE_PERFORMANCE Enables a set of (semi)invasive metrics. Various
1915 # instruments are enabled. The tools in
1916 # /usr/sbin/dpt_* assume these to be enabled.
1917 # DPT_HANDLE_TIMEOUTS Normally device timeouts are handled by the DPT.
1918 # If you ant the driver to handle timeouts, enable
1919 # this option. If your system is very busy, this
1920 # option will create more trouble than solve.
1921 # DPT_TIMEOUT_FACTOR Used to compute the excessive amount of time to
1922 # wait when timing out with the above option.
1923 # DPT_DEBUG_xxxx These are controllable from sys/dev/raid/dpt/dpt.h
1924 # DPT_LOST_IRQ When enabled, will try, once per second, to catch
1925 # any interrupt that got lost. Seems to help in some
1926 # DPT-firmware/Motherboard combinations. Minimal
1927 # cost, great benefit.
1928 # DPT_RESET_HBA Make "reset" actually reset the controller
1929 # instead of fudging it. Only enable this if you
1930 # are 100% certain you need it.
1935 #!CAM# options DPT_MEASURE_PERFORMANCE
1936 #!CAM# options DPT_HANDLE_TIMEOUTS
1937 options DPT_TIMEOUT_FACTOR=4
1938 options DPT_LOST_IRQ
1939 options DPT_RESET_HBA
1942 # Compaq "CISS" RAID controllers (SmartRAID 5* series)
1943 # These controllers have a SCSI-like interface, and require the
1944 # CAM infrastructure.
1949 # Intel Integrated RAID controllers.
1950 # This driver is supported and maintained by
1951 # "Leubner, Achim" <Achim_Leubner@adaptec.com>.
1956 # Mylex AcceleRAID and eXtremeRAID controllers with v6 and later
1957 # firmware. These controllers have a SCSI-like interface, and require
1958 # the CAM infrastructure.
1973 # General USB code (mandatory for USB)
1975 # Human Interface Device (anything with buttons and dials)
1981 # USB mass storage (Requires scbus and da)
1983 # USB mass storage driver for device-side mode
1989 # eGalax USB touch screen
1991 # Diamond Rio 500 MP3 player
2014 # USB ethernet support
2017 # ADMtek USB ethernet. Supports the LinkSys USB100TX,
2018 # the Billionton USB100, the Melco LU-ATX, the D-Link DSB-650TX
2019 # and the SMC 2202USB. Also works with the ADMtek AN986 Pegasus
2023 # ASIX Electronics AX88172 USB 2.0 ethernet driver. Used in the
2024 # LinkSys USB200M and various other adapters.
2027 # ASIX Electronics AX88178A/AX88179 USB 2.0/3.0 gigabit ethernet driver.
2030 # CATC USB-EL1201A USB ethernet. Supports the CATC Netmate
2031 # and Netmate II, and the Belkin F5U111.
2034 # USB Apple iPhone/iPad tethered Ethernet driver
2037 # Kawasaki LSI ethernet. Supports the LinkSys USB10T,
2038 # Entrega USB-NET-E45, Peracom Ethernet Adapter, the
2039 # 3Com 3c19250, the ADS Technologies USB-10BT, the ATen UC10T,
2040 # the Netgear EA101, the D-Link DSB-650, the SMC 2102USB
2041 # and 2104USB, and the Corega USB-T.
2044 # Moschip MCS7730/MCS7840 USB to fast ethernet. Supports the Sitecom LN030.
2047 # Davicom DM9601E USB to fast ethernet. Supports the Corega FEther USB-TXC.
2050 # USB wireless NICs, requires wlan_amrr
2052 # Ralink Technology RT2501USB/RT2601USB
2055 # Ralink Technology RT2700U/RT2800U/RT3000U wireless driver
2059 # RNDIS USB ethernet driver
2062 # Realtek RTL8188CU/RTL8192CU wireless driver
2065 options URTWN_WITHOUT_UCODE
2071 # Templates for programming USB device side drivers
2075 # debugging options for the USB subsystem
2080 options UKBD_DFLT_KEYMAP # specify the built-in keymap
2081 makeoptions UKBD_DFLT_KEYMAP=it.iso
2084 device firewire # Firewire bus code
2085 device sbp # SCSI over Firewire (Requires scbus and da)
2086 device fwe # Ethernet over Firewire (non-standard!)
2088 # dcons support (Dumb Console Device)
2089 device dcons # dumb console driver
2090 device dcons_crom # FireWire attachment
2091 options DCONS_BUF_SIZE=16384 # buffer size
2092 options DCONS_POLL_HZ=100 # polling rate
2093 options DCONS_FORCE_CONSOLE=1 # force to be the primary console
2094 options DCONS_FORCE_GDB=1 # force to be the gdb device
2096 #####################################################################
2099 # This is a port of the openbsd crypto framework. Include this when
2100 # configuring IPsec and when you have a h/w crypto device to accelerate
2101 # user applications that link to openssl.
2103 # Drivers are ports from openbsd with some simple enhancements that have
2104 # been fed back to openbsd (and hopefully will be included).
2106 device crypto # core crypto support
2107 device cryptodev # /dev/crypto for access to h/w
2109 device rndtest # FIPS 140-2 entropy tester
2111 device hifn # Hifn 7951, 7781, etc.
2112 options HIFN_DEBUG # enable debugging support: hw.hifn.debug
2113 #options HIFN_NO_RNG # for devices without RNG
2114 options HIFN_RNDTEST # enable rndtest support
2116 device safe # SafeNet 1141
2117 options SAFE_DEBUG # enable debugging support: hw.safe.debug
2118 #options SAFE_NO_RNG # for devices without RNG
2119 options SAFE_RNDTEST # enable rndtest support
2121 device ubsec # Broadcom 5501, 5601, 58xx
2122 options UBSEC_DEBUG # enable debugging support: hw.ubsec.debug
2123 #options UBSEC_NO_RNG # for devices without RNG
2124 options UBSEC_RNDTEST # enable rndtest support
2126 device aesni # hardware crypto/RNG for AES-NI
2127 device padlock # hardware crypto/RNG for VIA C3/C7/Eden
2128 device rdrand # hardware RNG for RdRand
2131 # ACPI support using the Intel ACPI Component Architecture reference
2134 # ACPI_DEBUG enables the use of the debug.acpi.level and debug.acpi.layer
2135 # kernel environment variables to select initial debugging levels for the
2136 # Intel ACPICA code.
2138 # Note that building ACPI into the kernel is deprecated; the module is
2139 # normally loaded automatically by the loader.
2144 # ACPI WMI Mapping driver
2147 # ACPI Asus Extras (LCD backlight/brightness, video output, etc.)
2150 # ACPI Fujitsu Extras (Buttons)
2153 # ACPI extras driver for HP laptops
2156 # ACPI Panasonic Extras (LCD backlight/brightness, video output, etc.)
2157 device acpi_panasonic
2159 # ACPI pvpanic driver for virtual machines running in Qemu
2162 # ACPI Sony extra (LCD brightness)
2165 # ACPI extras driver for ThinkPad laptops
2166 device acpi_thinkpad
2168 # ACPI Toshiba Extras (LCD backlight/brightness, video output, etc.)
2171 # ACPI Video Extensions (LCD backlight/brightness, video output, etc.)
2174 # ACPI Docking Station
2177 device aibs # ASUSTeK AI Booster (ACPI ASOC ATK0110)
2180 # drm: General DRM code
2181 # i915: Intel integrated GPUs, starting from the 830M family
2182 # radeon: ATI/AMD Radeon cards
2184 # DRM_DEBUG: include debug printfs, very slow
2186 # DRM requires AGP in the kernel.
2188 # Also you'll need to have the following 3 lines in the kernel config.
2195 # For testing and debugging.
2205 device cmx # Omnikey CardMan 4040 smartcard reader
2206 device amdsbwd # AMD South Bridge watchdog
2207 device gpio # Enable support for the gpio framework
2208 device ichwd # Intel ICH watchdog interrupt timer
2209 device tbridge # regression testing
2220 # Gpio support for ACPI based SoC platforms
2223 device gpio_intel # GPIO support for Intel SoCs
2226 # Embedded system options:
2228 # An embedded system might want to run something other than init.
2229 options INIT_PATH="/sbin/init:/sbin/oinit"
2232 options BUS_DEBUG # enable newbus debugging
2233 options RSS_DEBUG # enable RSS (Receive Side Scaling) debugging
2235 # Record the program counter of the code interrupted by the statistics
2236 # clock interrupt. Use pctrack(8) to dump this information.
2237 options DEBUG_PCTRACK
2239 # More undocumented options for linting.
2240 # Note that documenting these are not considered an affront.
2242 #options ACPI_NO_SEMAPHORES
2243 options AHC_DUMP_EEPROM
2244 #options BKTR_ALLOC_PAGES=xxx
2245 options CAM_DEBUG_DELAY
2246 options CLUSTERDEBUG
2247 #options COMPAT_LINUX
2249 options DEBUG_CRIT_SECTIONS
2250 #options DISABLE_PSE
2251 options BCE_RSS_DEBUG
2252 options BCE_TSS_DEBUG
2253 options BNX_RSS_DEBUG
2254 options BNX_TSO_DEBUG
2255 options BNX_TSS_DEBUG
2256 options EMX_RSS_DEBUG
2257 options EMX_TSO_DEBUG
2258 options EMX_TSS_DEBUG
2259 options JME_RSS_DEBUG
2260 options IGB_RSS_DEBUG
2261 options IGB_TSS_DEBUG
2262 options IGB_MSIX_DEBUG
2263 options IX_RSS_DEBUG
2264 options ENABLE_ALART
2266 options FB_INSTALL_CDEV
2267 options I586_PMC_GUPROF=0x70000
2268 #options IEEE80211_DEBUG_REFCNT
2269 options IEEE80211_SUPPORT_SUPERG
2270 options KBDIO_DEBUG=10
2271 options KBD_MAXRETRY=4
2272 options KBD_MAXWAIT=6
2273 options KBD_RESETDELAY=201
2274 #options KERN_TIMESTAMP
2278 #options MAXFILES=xxx
2280 options NO_LWKT_SPLIT_USERPRI
2284 options SCSI_NCR_DEBUG
2285 options SCSI_NCR_MAX_SYNC=10000
2286 options SCSI_NCR_MAX_WIDE=1
2287 options SCSI_NCR_MYADDR=7
2288 options SHOW_BUSYBUFS # List buffers that prevent root unmount
2291 options SOCKBUF_DEBUG
2292 options TDMA_BINTVAL_DEFAULT=5
2293 options TDMA_SLOTCNT_DEFAULT=2
2294 options TDMA_SLOTLEN_DEFAULT=10*1000
2295 options TDMA_TXRATE_11A_DEFAULT=2*24
2296 options TDMA_TXRATE_11B_DEFAULT=2*11
2297 options TDMA_TXRATE_11G_DEFAULT=2*24
2298 options TDMA_TXRATE_11NA_DEFAULT="(4|IEEE80211_RATE_MCS)"
2299 options TDMA_TXRATE_11NG_DEFAULT="(4|IEEE80211_RATE_MCS)"
2300 options TDMA_TXRATE_HALF_DEFAULT=2*12
2301 options TDMA_TXRATE_QUARTER_DEFAULT=2*6
2302 options TDMA_TXRATE_TURBO_DEFAULT=2*24
2303 #options TIMER_FREQ="((14318182+6)/12)"
2304 options VFS_BIO_DEBUG
2305 options VM_PAGE_DEBUG
2310 options KTR_ENTRIES=1024
2311 options KTR_VERBOSE=1
2312 #options KTR_ACPI_EC
2314 #options KTR_DMCRYPT
2315 #options KTR_ETHERNET
2321 #options KTR_IF_POLL
2322 #options KTR_IF_START
2324 #options KTR_KERNENTRY
2326 #options KTR_SERIALIZER
2327 #options KTR_SOWAKEUP
2328 #options KTR_SPIN_CONTENTION
2329 #options KTR_TESTLOG
2333 #options KTR_USCHED_BSD4
2334 #options KTR_USCHED_DFLY
2337 options ALTQ #alternate queueing
2338 options ALTQ_CBQ #class based queueing
2339 options ALTQ_RED #random early detection
2340 options ALTQ_RIO #triple red for diffserv (needs RED)
2341 options ALTQ_HFSC #hierarchical fair service curve
2342 options ALTQ_PRIQ #priority queue
2343 options ALTQ_FAIRQ #fair queue
2344 #options ALTQ_NOPCC #don't use processor cycle counter
2345 options ALTQ_DEBUG #for debugging
2346 # you might want to set kernel timer to 1kHz if you use CBQ,
2347 # especially with 100baseT
2351 options WDOG_DISABLE_ON_PANIC # Automatically disable watchdogs on panic
2354 options ERROR_LED_ON_PANIC # If an error led is present, light it up on panic
projects / dragonfly.git / blob