2 * HighPoint RR3xxx/4xxx RAID Driver for FreeBSD
3 * Copyright (C) 2007-2008 HighPoint Technologies, Inc. All Rights Reserved.
4 * Redistribution and use in source and binary forms, with or without
5 * modification, are permitted provided that the following conditions
7 * 1. Redistributions of source code must retain the above copyright
8 * notice, this list of conditions and the following disclaimer.
9 * 2. Redistributions in binary form must reproduce the above copyright
10 * notice, this list of conditions and the following disclaimer in the
11 * documentation and/or other materials provided with the distribution.
13 * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND
14 * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
15 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
16 * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE
17 * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
18 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
19 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
20 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
21 * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
22 * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
25 * $FreeBSD: src/sys/dev/hptiop/hptiop.h,v 1.5 2009/03/25 06:27:56 delphij Exp $
34 int hpt_iop_dbg_level = 0;
35 #define KdPrint(x) do { if (hpt_iop_dbg_level) kprintf x; } while (0)
40 #define HPT_SRB_MAX_REQ_SIZE 600
41 #define HPT_SRB_MAX_QUEUE_SIZE 0x100
44 #define HPT_SRB_FLAG_HIGH_MEM_ACESS 0x1
45 #define HPT_SRB_MAX_SIZE ((sizeof(struct hpt_iop_srb) + 0x1f) & ~0x1f)
47 #define offsetof(TYPE, MEM) ((size_t)&((TYPE*)0)->MEM)
51 #define MIN(a, b) ((a) < (b) ? (a) : (b))
54 #define HPT_IOCTL_MAGIC 0xA1B2C3D4
55 #define HPT_IOCTL_MAGIC32 0x1A2B3C4D
57 struct hpt_iopmu_itl {
58 u_int32_t resrved0[4];
59 u_int32_t inbound_msgaddr0;
60 u_int32_t inbound_msgaddr1;
61 u_int32_t outbound_msgaddr0;
62 u_int32_t outbound_msgaddr1;
63 u_int32_t inbound_doorbell;
64 u_int32_t inbound_intstatus;
65 u_int32_t inbound_intmask;
66 u_int32_t outbound_doorbell;
67 u_int32_t outbound_intstatus;
68 u_int32_t outbound_intmask;
69 u_int32_t reserved1[2];
70 u_int32_t inbound_queue;
71 u_int32_t outbound_queue;
74 #define IOPMU_QUEUE_EMPTY 0xffffffff
75 #define IOPMU_QUEUE_MASK_HOST_BITS 0xf0000000
76 #define IOPMU_QUEUE_ADDR_HOST_BIT 0x80000000
77 #define IOPMU_QUEUE_REQUEST_SIZE_BIT 0x40000000
78 #define IOPMU_QUEUE_REQUEST_RESULT_BIT 0x40000000
79 #define IOPMU_MAX_MEM_SUPPORT_MASK_64G 0xfffffff000000000ull
80 #define IOPMU_MAX_MEM_SUPPORT_MASK_32G 0xfffffff800000000ull
82 #define IOPMU_OUTBOUND_INT_MSG0 1
83 #define IOPMU_OUTBOUND_INT_MSG1 2
84 #define IOPMU_OUTBOUND_INT_DOORBELL 4
85 #define IOPMU_OUTBOUND_INT_POSTQUEUE 8
86 #define IOPMU_OUTBOUND_INT_PCI 0x10
88 #define IOPMU_INBOUND_INT_MSG0 1
89 #define IOPMU_INBOUND_INT_MSG1 2
90 #define IOPMU_INBOUND_INT_DOORBELL 4
91 #define IOPMU_INBOUND_INT_ERROR 8
92 #define IOPMU_INBOUND_INT_POSTQUEUE 0x10
94 #define MVIOP_QUEUE_LEN 512
96 u_int32_t inbound_head;
97 u_int32_t inbound_tail;
98 u_int32_t outbound_head;
99 u_int32_t outbound_tail;
100 u_int32_t inbound_msg;
101 u_int32_t outbound_msg;
102 u_int32_t reserve[10];
103 u_int64_t inbound_q[MVIOP_QUEUE_LEN];
104 u_int64_t outbound_q[MVIOP_QUEUE_LEN];
107 struct hpt_iopmv_regs {
108 u_int32_t reserved[0x20400 / 4];
109 u_int32_t inbound_doorbell;
110 u_int32_t inbound_intmask;
111 u_int32_t outbound_doorbell;
112 u_int32_t outbound_intmask;
115 #define MVIOP_IOCTLCFG_SIZE 0x800
116 #define MVIOP_MU_QUEUE_ADDR_HOST_MASK (~(0x1full))
117 #define MVIOP_MU_QUEUE_ADDR_HOST_BIT 4
119 #define MVIOP_MU_QUEUE_ADDR_IOP_HIGH32 0xffffffff
120 #define MVIOP_MU_QUEUE_REQUEST_RESULT_BIT 1
121 #define MVIOP_MU_QUEUE_REQUEST_RETURN_CONTEXT 2
123 #define MVIOP_MU_INBOUND_INT_MSG 1
124 #define MVIOP_MU_INBOUND_INT_POSTQUEUE 2
125 #define MVIOP_MU_OUTBOUND_INT_MSG 1
126 #define MVIOP_MU_OUTBOUND_INT_POSTQUEUE 2
128 #define MVIOP_CMD_TYPE_GET_CONFIG (1 << 5)
129 #define MVIOP_CMD_TYPE_SET_CONFIG (1 << 6)
130 #define MVIOP_CMD_TYPE_SCSI (1 << 7)
131 #define MVIOP_CMD_TYPE_IOCTL (1 << 8)
132 #define MVIOP_CMD_TYPE_BLOCK (1 << 9)
134 #define MVIOP_REQUEST_NUMBER_START_BIT 16
136 enum hpt_iopmu_message {
137 /* host-to-iop messages */
138 IOPMU_INBOUND_MSG0_NOP = 0,
139 IOPMU_INBOUND_MSG0_RESET,
140 IOPMU_INBOUND_MSG0_FLUSH,
141 IOPMU_INBOUND_MSG0_SHUTDOWN,
142 IOPMU_INBOUND_MSG0_STOP_BACKGROUND_TASK,
143 IOPMU_INBOUND_MSG0_START_BACKGROUND_TASK,
144 IOPMU_INBOUND_MSG0_MAX = 0xff,
145 /* iop-to-host messages */
146 IOPMU_OUTBOUND_MSG0_REGISTER_DEVICE_0 = 0x100,
147 IOPMU_OUTBOUND_MSG0_REGISTER_DEVICE_MAX = 0x1ff,
148 IOPMU_OUTBOUND_MSG0_UNREGISTER_DEVICE_0 = 0x200,
149 IOPMU_OUTBOUND_MSG0_UNREGISTER_DEVICE_MAX = 0x2ff,
150 IOPMU_OUTBOUND_MSG0_REVALIDATE_DEVICE_0 = 0x300,
151 IOPMU_OUTBOUND_MSG0_REVALIDATE_DEVICE_MAX = 0x3ff,
154 #define IOP_REQUEST_FLAG_SYNC_REQUEST 1
155 #define IOP_REQUEST_FLAG_BIST_REQUEST 2
156 #define IOP_REQUEST_FLAG_REMAPPED 4
157 #define IOP_REQUEST_FLAG_OUTPUT_CONTEXT 8
159 enum hpt_iop_request_type {
160 IOP_REQUEST_TYPE_GET_CONFIG = 0,
161 IOP_REQUEST_TYPE_SET_CONFIG,
162 IOP_REQUEST_TYPE_BLOCK_COMMAND,
163 IOP_REQUEST_TYPE_SCSI_COMMAND,
164 IOP_REQUEST_TYPE_IOCTL_COMMAND,
168 enum hpt_iop_result_type {
169 IOP_RESULT_PENDING = 0,
174 IOP_RESULT_INVALID_REQUEST,
175 IOP_RESULT_BAD_TARGET,
176 IOP_RESULT_CHECK_CONDITION,
179 struct hpt_iop_request_header {
184 u_int64_t context; /* host context */
187 struct hpt_iop_request_get_config {
188 struct hpt_iop_request_header header;
189 u_int32_t interface_version;
190 u_int32_t firmware_version;
191 u_int32_t max_requests;
192 u_int32_t request_size;
193 u_int32_t max_sg_count;
194 u_int32_t data_transfer_length;
195 u_int32_t alignment_mask;
196 u_int32_t max_devices;
197 u_int32_t sdram_size;
200 struct hpt_iop_request_set_config {
201 struct hpt_iop_request_header header;
204 u_int16_t max_host_request_size;
205 u_int32_t reserve[6];
210 u_int32_t eot; /* non-zero: end of table */
211 u_int64_t pci_address;
214 #define IOP_BLOCK_COMMAND_READ 1
215 #define IOP_BLOCK_COMMAND_WRITE 2
216 #define IOP_BLOCK_COMMAND_VERIFY 3
217 #define IOP_BLOCK_COMMAND_FLUSH 4
218 #define IOP_BLOCK_COMMAND_SHUTDOWN 5
219 struct hpt_iop_request_block_command {
220 struct hpt_iop_request_header header;
225 u_int16_t command; /* IOP_BLOCK_COMMAND_{READ,WRITE} */
228 struct hpt_iopsg sg_list[1];
231 struct hpt_iop_request_scsi_command {
232 struct hpt_iop_request_header header;
238 u_int32_t dataxfer_length;
239 struct hpt_iopsg sg_list[1];
242 struct hpt_iop_request_ioctl_command {
243 struct hpt_iop_request_header header;
244 u_int32_t ioctl_code;
245 u_int32_t inbuf_size;
246 u_int32_t outbuf_size;
247 u_int32_t bytes_returned;
249 /* out data should be put at buf[(inbuf_size+3)&~3] */
252 struct hpt_iop_ioctl_param {
253 u_int32_t Magic; /* used to check if it's a valid ioctl packet */
254 u_int32_t dwIoControlCode; /* operation control code */
255 unsigned long lpInBuffer; /* input data buffer */
256 u_int32_t nInBufferSize; /* size of input data buffer */
257 unsigned long lpOutBuffer; /* output data buffer */
258 u_int32_t nOutBufferSize; /* size of output data buffer */
259 unsigned long lpBytesReturned; /* count of HPT_U8s returned */
262 #define HPT_IOCTL_FLAG_OPEN 1
263 #define HPT_CTL_CODE_BSD_TO_IOP(x) ((x)-0xff00)
265 typedef struct cdev * ioctl_dev_t;
267 typedef struct thread * ioctl_thread_t;
270 struct hptiop_adapter_ops *ops;
273 struct hpt_iopmu_itl *mu;
276 struct hpt_iopmv_regs *regs;
277 struct hpt_iopmu_mv *mu;
281 struct hpt_iop_hba *next;
283 u_int32_t firmware_version;
284 u_int32_t interface_version;
285 u_int32_t max_devices;
286 u_int32_t max_requests;
287 u_int32_t max_request_size;
288 u_int32_t max_sg_count;
293 ioctl_dev_t ioctl_dev;
295 bus_dma_tag_t parent_dmat;
296 bus_dma_tag_t io_dmat;
297 bus_dma_tag_t srb_dmat;
298 bus_dma_tag_t ctlcfg_dmat;
300 bus_dmamap_t srb_dmamap;
301 bus_dmamap_t ctlcfg_dmamap;
303 struct resource *bar0_res;
304 bus_space_tag_t bar0t;
305 bus_space_handle_t bar0h;
308 struct resource *bar2_res;
309 bus_space_tag_t bar2t;
310 bus_space_handle_t bar2h;
314 u_int8_t *uncached_ptr;
316 /* for scsi request block */
317 struct hpt_iop_srb *srb_list;
319 struct resource *irq_res;
322 /* for ioctl and set/get config */
323 struct resource *ctlcfg_res;
325 u_int64_t ctlcfgcmd_phy;
326 u_int32_t config_done;
328 /* other resources */
330 struct cam_path *path;
333 #define HPT_IOCTL_FLAG_OPEN 1
335 struct hpt_iop_srb* srb[HPT_SRB_MAX_QUEUE_SIZE];
338 struct hptiop_adapter_ops {
339 int (*iop_wait_ready)(struct hpt_iop_hba *hba, u_int32_t millisec);
340 int (*internal_memalloc)(struct hpt_iop_hba *hba);
341 int (*internal_memfree)(struct hpt_iop_hba *hba);
342 int (*alloc_pci_res)(struct hpt_iop_hba *hba);
343 void (*release_pci_res)(struct hpt_iop_hba *hba);
344 void (*enable_intr)(struct hpt_iop_hba *hba);
345 void (*disable_intr)(struct hpt_iop_hba *hba);
346 int (*get_config)(struct hpt_iop_hba *hba,
347 struct hpt_iop_request_get_config *config);
348 int (*set_config)(struct hpt_iop_hba *hba,
349 struct hpt_iop_request_set_config *config);
350 int (*iop_intr)(struct hpt_iop_hba *hba);
351 void (*post_msg)(struct hpt_iop_hba *hba, u_int32_t msg);
352 void (*post_req)(struct hpt_iop_hba *hba, struct hpt_iop_srb *srb, bus_dma_segment_t *segs, int nsegs);
353 int (*do_ioctl)(struct hpt_iop_hba *hba, struct hpt_iop_ioctl_param * pParams);
357 u_int8_t req[HPT_SRB_MAX_REQ_SIZE];
358 struct hpt_iop_hba *hba;
360 struct hpt_iop_srb *next;
361 bus_dmamap_t dma_map;
367 #define hptiop_lock_adapter(hba) lockmgr(&(hba)->lock, LK_EXCLUSIVE)
368 #define hptiop_unlock_adapter(hba) lockmgr(&(hba)->lock, LK_RELEASE)
370 #define HPT_OSM_TIMEOUT (20*hz) /* timeout value for OS commands */
372 #define HPT_DO_IOCONTROL _IOW('H', 0, struct hpt_iop_ioctl_param)
373 #define HPT_SCAN_BUS _IO('H', 1)
375 static __inline int hptiop_sleep(struct hpt_iop_hba *hba, void *ident,
376 int priority, const char *wmesg, int timo)
381 retval = lksleep(ident, &hba->lock, priority, wmesg, timo);