2 # LINT -- config file for checking all the sources, tries to pull in
3 # as much of the source tree as it can.
5 # $FreeBSD: src/sys/i386/conf/LINT,v 1.749.2.144 2003/06/04 17:56:59 sam Exp $
6 # $DragonFly: src/sys/i386/conf/Attic/LINT,v 1.64 2005/10/18 15:31:10 sephe Exp $
8 # NB: You probably don't want to try running a kernel built from this
9 # file. Instead, you should start from GENERIC, and add options from
10 # this file as required.
14 # This directive is mandatory; it defines the architecture to be
15 # configured for; in this case, the 386 family based IBM-PC and
21 # This is the ``identification'' of the kernel. Usually this should
22 # be the same as the name of your kernel.
27 # The `maxusers' parameter controls the static sizing of a number of
28 # internal system tables by a formula defined in subr_param.c. Setting
29 # maxusers to 0 will cause the system to auto-size based on physical
35 # The `makeoptions' parameter allows variables to be passed to the
36 # generated Makefile in the build area.
38 # CONF_CFLAGS gives some extra compiler flags that are added to ${CFLAGS}
39 # after most other flags. Here we use it to inhibit use of non-optimal
40 # gcc builtin functions (e.g., memcmp).
42 # DEBUG happens to be magic.
43 # The following is equivalent to 'config -g KERNELNAME' and creates
44 # 'kernel.debug' compiled with -g debugging as well as a normal
45 # 'kernel'. Use 'make install.debug' to install the debug kernel
46 # but that isn't normally necessary as the debug symbols are not loaded
47 # by the kernel and are not useful there anyway.
49 # KERNEL can be overridden so that you can change the default name of your
52 # MODULES_OVERRIDE can be used to limit modules built to a specific list.
54 # INSTALLSTRIPPED can be set to cause installkernel to install stripped
55 # kernels and modules rather than a kernel and modules with debug symbols.
57 # INSTALLSTRIPPEDMODULES can be set to allow a full debug kernel to be
58 # installed, but to strip the installed modules.
60 makeoptions CONF_CFLAGS=-fno-builtin #Don't allow use of memcmp, etc.
61 #makeoptions DEBUG=-g #Build kernel with gdb(1) debug symbols
62 #makeoptions KERNEL=foo #Build kernel "foo" and install "/foo"
63 # Only build Linux API modules and plus those parts of the sound system I need.
64 #makeoptions MODULES_OVERRIDE="linux sound/snd sound/pcm sound/driver/maestro3"
65 #makeoptions INSTALLSTRIPPED=1
66 #makeoptions INSTALLSTRIPPEDMODULES=1
69 # Certain applications can grow to be larger than the 128M limit
70 # that FreeBSD initially imposes. Below are some options to
71 # allow that limit to grow to 256MB, and can be increased further
72 # with changing the parameters. MAXDSIZ is the maximum that the
73 # limit can be set to, and the DFLDSIZ is the default value for
74 # the limit. MAXSSIZ is the maximum that the stack limit can be
75 # set to. You might want to set the default lower than the max,
76 # and explicitly set the maximum with a shell command for processes
77 # that regularly exceed the limit like INND.
79 options MAXDSIZ="(256*1024*1024)"
80 options MAXSSIZ="(256*1024*1024)"
81 options DFLDSIZ="(256*1024*1024)"
84 # BLKDEV_IOSIZE sets the default block size used in user block
85 # device I/O. Note that this value will be overriden by the label
86 # when specifying a block device from a label with a non-0
87 # partition blocksize. The default is PAGE_SIZE.
89 options BLKDEV_IOSIZE=8192
91 # Options for the VM subsystem.
92 options PQ_CACHESIZE=512 # color for 512k/16k cache
94 # This allows you to actually store this configuration file into
95 # the kernel binary itself, where it may be later read by saying:
96 # strings -n 3 /kernel | sed -n 's/^___//p' > MYKERNEL
98 options INCLUDE_CONFIG_FILE # Include this file in kernel
101 # The root device and filesystem type can be compiled in;
102 # this provides a fallback option if the root device cannot
103 # be correctly guessed by the bootstrap code, or an override if
104 # the RB_DFLTROOT flag (-r) is specified when booting the kernel.
106 options ROOTDEVNAME=\"ufs:da0s2e\"
109 #####################################################################
112 # SMP enables building of a Symmetric MultiProcessor Kernel.
113 # APIC_IO enables the use of the IO APIC for Symmetric I/O.
117 # An SMP kernel will ONLY run on an Intel MP spec. qualified motherboard.
119 # Be sure to disable 'cpu I386_CPU' && 'cpu I486_CPU' for SMP kernels.
121 # Check the 'Rogue SMP hardware' section to see if additional options
122 # are required by your hardware.
126 options SMP # Symmetric MultiProcessor Kernel
127 options APIC_IO # Symmetric (APIC) I/O
130 # Rogue SMP hardware:
135 # The MP tables of most of the current generation MP motherboards
136 # do NOT properly support bridged PCI cards. To use one of these
137 # cards you should refer to ???
140 #####################################################################
144 # You must specify at least one CPU (the one you intend to run on);
145 # deleting the specification for CPUs you don't need to use may make
146 # parts of the system run faster. This is especially true removing
151 cpu I586_CPU # aka Pentium(tm)
152 cpu I686_CPU # aka Pentium Pro(tm)
155 # Options for CPU features.
157 # CPU_ATHLON_SSE_HACK tries to enable SSE instructions when the BIOS has
158 # forgotten to enable them.
160 # CPU_BLUELIGHTNING_FPU_OP_CACHE enables FPU operand cache on IBM
161 # BlueLightning CPU. It works only with Cyrix FPU, and this option
162 # should not be used with Intel FPU.
164 # CPU_BLUELIGHTNING_3X enables triple-clock mode on IBM Blue Lightning
165 # CPU if CPU supports it. The default is double-clock mode on
166 # BlueLightning CPU box.
168 # CPU_BTB_EN enables branch target buffer on Cyrix 5x86 (NOTE 1).
170 # CPU_DIRECT_MAPPED_CACHE sets L1 cache of Cyrix 486DLC CPU in direct
171 # mapped mode. Default is 2-way set associative mode.
173 # CPU_CYRIX_NO_LOCK enables weak locking for the entire address space
174 # of Cyrix 6x86 and 6x86MX CPUs by setting the NO_LOCK bit of CCR1.
175 # Otherwise, the NO_LOCK bit of CCR1 is cleared. (NOTE 3)
177 # CPU_DISABLE_5X86_LSSER disables load store serialize (i.e. enables
178 # reorder). This option should not be used if you use memory mapped
181 # CPU_DISABLE_SSE disables SSE/MMX2 instructions support.
183 # CPU_ENABLE_TCC enables Thermal Control Circuitry (TCC) found in some
184 # Pentium(tm) 4 and (possibly) later CPUs. When enabled and detected,
185 # TCC supports restricting power consumption using the hw.p4tcc.*
186 # sysctls. This operates independently of SpeedStep and is useful on
187 # systems where other mechanisms such as apm(4) or acpi(4) don't work.
189 # CPU_FASTER_5X86_FPU enables faster FPU exception handler.
191 # CPU_I486_ON_386 enables CPU cache on i486 based CPU upgrade products
194 # CPU_IORT defines I/O clock delay time (NOTE 1). Default values of
195 # I/O clock delay time on Cyrix 5x86 and 6x86 are 0 and 7,respectively
198 # CPU_L2_LATENCY specifed the L2 cache latency value. This option is used
199 # only when CPU_PPRO2CELERON is defined and Mendocino Celeron is detected.
200 # The default value is 5.
202 # CPU_ELAN enables support for AMDs ElanSC520 CPU.
204 # CPU_LOOP_EN prevents flushing the prefetch buffer if the destination
205 # of a jump is already present in the prefetch buffer on Cyrix 5x86(NOTE
208 # CPU_PPRO2CELERON enables L2 cache of Mendocino Celeron CPUs. This option
209 # is useful when you use Socket 8 to Socket 370 converter, because most Pentium
210 # Pro BIOSs do not enable L2 cache of Mendocino Celeron CPUs.
212 # CPU_RSTK_EN enables return stack on Cyrix 5x86 (NOTE 1).
214 # CPU_SUSP_HLT enables suspend on HALT. If this option is set, CPU
215 # enters suspend mode following execution of HALT instruction.
217 # CPU_WT_ALLOC enables write allocation on Cyrix 6x86/6x86MX and AMD
220 # CYRIX_CACHE_WORKS enables CPU cache on Cyrix 486 CPUs with cache
221 # flush at hold state.
223 # CYRIX_CACHE_REALLY_WORKS enables (1) CPU cache on Cyrix 486 CPUs
224 # without cache flush at hold state, and (2) write-back CPU cache on
225 # Cyrix 6x86 whose revision < 2.7 (NOTE 2).
227 # NO_F00F_HACK disables the hack that prevents Pentiums (and ONLY
228 # Pentiums) from locking up when a LOCK CMPXCHG8B instruction is
229 # executed. This option is only needed if I586_CPU is also defined,
230 # and should be included for any non-Pentium CPU that defines it.
232 # NO_MEMORY_HOLE is an optimisation for systems with AMD K6 processors
233 # which indicates that the 15-16MB range is *definitely* not being
234 # occupied by an ISA memory hole.
236 # NOTE 1: The options, CPU_BTB_EN, CPU_LOOP_EN, CPU_IORT,
237 # CPU_LOOP_EN and CPU_RSTK_EN should not be used because of CPU bugs.
238 # These options may crash your system.
240 # NOTE 2: If CYRIX_CACHE_REALLY_WORKS is not set, CPU cache is enabled
241 # in write-through mode when revision < 2.7. If revision of Cyrix
242 # 6x86 >= 2.7, CPU cache is always enabled in write-back mode.
244 # NOTE 3: This option may cause failures for software that requires
245 # locked cycles in order to operate correctly.
247 options CPU_ATHLON_SSE_HACK
248 options CPU_BLUELIGHTNING_FPU_OP_CACHE
249 options CPU_BLUELIGHTNING_3X
251 options CPU_DIRECT_MAPPED_CACHE
252 options CPU_DISABLE_5X86_LSSER
254 options CPU_ENABLE_TCC
255 options CPU_DISABLE_SSE
256 options CPU_FASTER_5X86_FPU
257 options CPU_I486_ON_386
259 options CPU_L2_LATENCY=5
261 options CPU_PPRO2CELERON
265 options CYRIX_CACHE_WORKS
266 options CYRIX_CACHE_REALLY_WORKS
267 #options NO_F00F_HACK
270 # A math emulator is mandatory if you wish to run on hardware which
271 # does not have a floating-point processor.
272 options MATH_EMULATE #Support for x87 emulation
274 #####################################################################
275 # COMPATIBILITY OPTIONS
278 # Implement system calls compatible with 4.3BSD and older versions of
279 # FreeBSD. You probably do NOT want to remove this as much current code
280 # still relies on the 4.3 emulation.
285 # Implement system calls compatible with DragonFly 1.2 and older.
287 options COMPAT_DF12 #Compatible with DragonFly 1.2 and earlier
290 # These three options provide support for System V Interface
291 # Definition-style interprocess communication, in the form of shared
292 # memory, semaphores, and message queues, respectively.
294 # System V shared memory and tunable parameters
295 options SYSVSHM # include support for shared memory
296 options SHMMAXPGS=1025 # max amount of shared memory pages (4k on i386)
297 options SHMALL=1025 # max amount of shared memory (bytes)
298 options SHMMAX="(SHMMAXPGS*PAGE_SIZE+1)"
299 # max shared memory segment size (bytes)
300 options SHMMIN=2 # min shared memory segment size (bytes)
301 options SHMMNI=33 # max number of shared memory identifiers
302 options SHMSEG=9 # max shared memory segments per process
304 # System V semaphores and tunable parameters
305 options SYSVSEM # include support for semaphores
306 options SEMMAP=31 # amount of entries in semaphore map
307 options SEMMNI=11 # number of semaphore identifiers in the system
308 options SEMMNS=61 # number of semaphores in the system
309 options SEMMNU=31 # number of undo structures in the system
310 options SEMMSL=61 # max number of semaphores per id
311 options SEMOPM=101 # max number of operations per semop call
312 options SEMUME=11 # max number of undo entries per process
314 # System V message queues and tunable parameters
315 options SYSVMSG # include support for message queues
316 options MSGMNB=2049 # max characters per message queue
317 options MSGMNI=41 # max number of message queue identifiers
318 options MSGSEG=2049 # max number of message segments in the system
319 options MSGSSZ=16 # size of a message segment MUST be power of 2
320 options MSGTQL=41 # max amount of messages in the system
323 #####################################################################
327 # Enable the kernel debugger.
332 # Don't drop into DDB for a panic. Intended for unattended operation
333 # where you may want to drop to DDB from the console, but still want
334 # the machine to recover from a panic
336 options DDB_UNATTENDED
339 # If using GDB remote mode to debug the kernel, there's a non-standard
340 # extension to the remote protocol that can be used to use the serial
341 # port as both the debugging port and the system console. It's non-
342 # standard and you're on your own if you enable it. See also the
343 # "remotechat" variables in the FreeBSD specific version of gdb.
345 options GDB_REMOTE_CHAT
348 # KTRACE enables the system-call tracing facility ktrace(2).
350 options KTRACE #kernel tracing
353 # The INVARIANTS option is used in a number of source files to enable
354 # extra sanity checking of internal structures. This support is not
355 # enabled by default because of the extra time it would take to check
356 # for these conditions, which can only occur as a result of
357 # programming errors.
362 # The INVARIANT_SUPPORT option makes us compile in support for
363 # verifying some of the internal structures. It is a prerequisite for
364 # 'INVARIANTS', as enabling 'INVARIANTS' will make these functions be
365 # called. The intent is that you can set 'INVARIANTS' for single
366 # source files (by changing the source file or specifying it on the
367 # command line) if you have 'INVARIANT_SUPPORT' enabled.
369 options INVARIANT_SUPPORT
372 # The DIAGNOSTIC option is used to enable extra debugging information
373 # from some parts of the kernel. As this makes everything more noisy,
374 # it is disabled by default.
379 # PERFMON causes the driver for Pentium/Pentium Pro performance counters
380 # to be compiled. See perfmon(4) for more information.
386 # This option let some drivers co-exist that can't co-exist in a running
387 # system. This is used to be able to compile all kernel code in one go for
388 # quality assurance purposes (like this file, which the option takes it name
391 options COMPILING_LINT
394 # XXX - this doesn't belong here.
395 # Allow ordinary users to take the console - this is useful for X.
398 # XXX - this doesn't belong here either
399 options USERCONFIG #boot -c editor
400 options INTRO_USERCONFIG #imply -c and show intro screen
401 options VISUAL_USERCONFIG #visual boot -c editor
404 #####################################################################
409 # Only the INET (Internet) family is officially supported in FreeBSD.
410 # Source code for the NS (Xerox Network Service) is provided for amusement
413 options INET #Internet communications protocols
414 options INET6 #IPv6 communications protocols
415 options IPSEC #IP security
416 options IPSEC_ESP #IP security (crypto; define w/ IPSEC)
417 options IPSEC_DEBUG #debug for IP security
419 # Set IPSEC_FILTERGIF to force packets coming through a gif tunnel
420 # to be processed by any configured packet filtering (ipfw, ipf).
421 # The default is that packets coming from a tunnel are _not_ processed;
422 # they are assumed trusted.
424 # Note that enabling this can be problematic as there are no mechanisms
425 # in place for distinguishing packets coming out of a tunnel (e.g. no
426 # encX devices as found on openbsd).
428 #options IPSEC_FILTERGIF #filter ipsec packets from a tunnel
431 # Experimental IPsec implementation that uses the kernel crypto
432 # framework. This cannot be configured together with IPSEC and
433 # (currently) supports only IPv4. To use this you must also
434 # configure the crypto device (see below). Note that with this
435 # you get all the IPsec protocols (e.g. there is no FAST_IPSEC_ESP).
436 # IPSEC_DEBUG is used, as above, to configure debugging support
437 # within the IPsec protocols.
439 #options FAST_IPSEC #new IPsec
441 options IPX #IPX/SPX communications protocols
442 options IPXIP #IPX in IP encapsulation (not available)
443 options IPTUNNEL #IP in IPX encapsulation (not available)
445 options NCP #NetWare Core protocol
447 options NETATALK #Appletalk communications protocols
449 # These are currently broken but are shipped due to interest.
450 #options NS #Xerox NS protocols
451 #options NSIP #XNS over IP
455 # NETSMB enables support for SMB protocol, it requires LIBMCHAIN and LIBICONV
457 # NETSMBCRYPTO enables support for encrypted passwords.
458 options NETSMB #SMB/CIFS requester
459 options NETSMBCRYPTO #encrypted password support for SMB
461 # mchain library. It can be either loaded as KLD or compiled into kernel
462 options LIBMCHAIN #mbuf management library
464 # netgraph(4). Enable the base netgraph code with the NETGRAPH option.
465 # Individual node types can be enabled with the corresponding option
466 # listed below; however, this is not strictly necessary as netgraph
467 # will automatically load the corresponding KLD module if the node type
468 # is not already compiled into the kernel. Each type below has a
469 # corresponding man page, e.g., ng_async(8).
470 options NETGRAPH #netgraph(4) system
471 options NETGRAPH_ASYNC
473 options NETGRAPH_CISCO
474 options NETGRAPH_ECHO
475 options NETGRAPH_ETHER
476 options NETGRAPH_FRAME_RELAY
477 options NETGRAPH_HOLE
478 options NETGRAPH_IFACE
479 options NETGRAPH_KSOCKET
480 options NETGRAPH_L2TP
482 # MPPC compression requires proprietary files (not included)
483 #options NETGRAPH_MPPC_COMPRESSION
484 options NETGRAPH_MPPC_ENCRYPTION
485 options NETGRAPH_ONE2MANY
487 options NETGRAPH_PPPOE
488 options NETGRAPH_PPTPGRE
489 options NETGRAPH_RFC1490
490 options NETGRAPH_SOCKET
496 device mn # Munich32x/Falc54 Nx64kbit/sec cards.
499 # Network interfaces:
500 # The `loop' pseudo-device is MANDATORY when networking is enabled.
501 # The `ether' pseudo-device provides generic code to handle
502 # Ethernets; it is MANDATORY when a Ethernet device driver is
503 # configured or token-ring is enabled.
504 # The 'fddi' pseudo-device provides generic code to support FDDI.
505 # The `arcnet' pseudo-device provides generic code to support Arcnet.
506 # The `sppp' pseudo-device serves a similar role for certain types
507 # of synchronous PPP links (like `cx', `ar').
508 # The `sl' pseudo-device implements the Serial Line IP (SLIP) service.
509 # The `ppp' pseudo-device implements the Point-to-Point Protocol.
510 # The `bpf' pseudo-device enables the Berkeley Packet Filter. Be
511 # aware of the legal and administrative consequences of enabling this
512 # option. The number of devices determines the maximum number of
513 # simultaneous BPF clients programs runnable.
514 # The `disc' pseudo-device implements a minimal network interface,
515 # which throws away all packets sent and never receives any. It is
516 # included for testing purposes. This shows up as the 'ds' interface.
517 # The `tun' pseudo-device implements (user-)ppp and nos-tun
518 # The `gif' pseudo-device implements IPv6 over IP4 tunneling,
519 # IPv4 over IPv6 tunneling, IPv4 over IPv4 tunneling and
520 # IPv6 over IPv6 tunneling.
521 # The `gre' device implements two types of IP4 over IP4 tunneling:
522 # GRE and MOBILE, as specified in the RFC1701 and RFC2004.
523 # The `faith' pseudo-device captures packets sent to it and diverts them
524 # to the IPv4/IPv6 translation daemon.
525 # The `stf' device implements 6to4 encapsulation.
526 # The `ef' pseudo-device provides support for multiple ethernet frame types
527 # specified via ETHER_* options. See ef(4) for details.
529 # The PPP_BSDCOMP option enables support for compress(1) style entire
530 # packet compression, the PPP_DEFLATE is for zlib/gzip style compression.
531 # PPP_FILTER enables code for filtering the ppp data stream and selecting
532 # events for resetting the demand dial activity timer - requires bpf.
533 # See pppd(8) for more details.
535 pseudo-device ether #Generic Ethernet
536 pseudo-device vlan 1 #VLAN support
537 pseudo-device token #Generic TokenRing
538 pseudo-device fddi #Generic FDDI
539 pseudo-device arcnet #Generic Arcnet
540 pseudo-device sppp #Generic Synchronous PPP
541 pseudo-device loop #Network loopback device
542 pseudo-device bpf #Berkeley packet filter
543 pseudo-device disc #Discard device (ds0, ds1, etc)
544 pseudo-device tun #Tunnel driver (ppp(8), nos-tun(8))
545 pseudo-device sl 2 #Serial Line IP
546 pseudo-device gre #IP over IP tunneling
547 pseudo-device ppp 2 #Point-to-point protocol
548 options PPP_BSDCOMP #PPP BSD-compress support
549 options PPP_DEFLATE #PPP zlib/deflate/gzip support
550 options PPP_FILTER #enable bpf filtering (needs bpf)
552 pseudo-device ef # Multiple ethernet frames support
553 options ETHER_II # enable Ethernet_II frame
554 options ETHER_8023 # enable Ethernet_802.3 (Novell) frame
555 options ETHER_8022 # enable Ethernet_802.2 frame
556 options ETHER_SNAP # enable Ethernet_802.2/SNAP frame
559 pseudo-device gif #IPv6 and IPv4 tunneling
560 pseudo-device faith 1 #for IPv6 and IPv4 translation
561 pseudo-device stf #6to4 IPv6 over IPv4 encapsulation
564 # Internet family options:
566 # MROUTING enables the kernel multicast packet forwarder, which works
569 # PIM enables Protocol Independent Multicast in the kernel.
570 # Requires MROUTING enabled.
572 # IPFIREWALL enables support for IP firewall construction, in
573 # conjunction with the `ipfw' program. IPFIREWALL_VERBOSE sends
574 # logged packets to the system logger. IPFIREWALL_VERBOSE_LIMIT
575 # limits the number of times a matching entry can be logged.
577 # WARNING: IPFIREWALL defaults to a policy of "deny ip from any to any"
578 # and if you do not add other rules during startup to allow access,
579 # YOU WILL LOCK YOURSELF OUT. It is suggested that you set firewall_type=open
580 # in /etc/rc.conf when first enabling this feature, then refining the
581 # firewall rules in /etc/rc.firewall after you've tested that the new kernel
582 # feature works properly.
584 # IPFIREWALL_DEFAULT_TO_ACCEPT causes the default rule (at boot) to
585 # allow everything. Use with care, if a cracker can crash your
586 # firewall machine, they can get to your protected machines. However,
587 # if you are using it as an as-needed filter for specific problems as
588 # they arise, then this may be for you. Changing the default to 'allow'
589 # means that you won't get stuck if the kernel and /sbin/ipfw binary get
592 # IPDIVERT enables the divert IP sockets, used by ``ipfw divert''
594 # IPSTEALTH enables code to support stealth forwarding (i.e., forwarding
595 # packets without touching the ttl). This can be useful to hide firewalls
596 # from traceroute and similar tools.
598 # TCPDEBUG is undocumented.
600 options MROUTING # Multicast routing
601 options PIM # Protocol Independent Multicast
602 options IPFIREWALL #firewall
603 options IPFIREWALL_VERBOSE #enable logging to syslogd(8)
604 options IPFIREWALL_FORWARD #enable transparent proxy support
605 options IPFIREWALL_VERBOSE_LIMIT=100 #limit verbosity
606 options IPFIREWALL_DEFAULT_TO_ACCEPT #allow everything by default
607 options IPV6FIREWALL #firewall for IPv6
608 options IPV6FIREWALL_VERBOSE
609 options IPV6FIREWALL_VERBOSE_LIMIT=100
610 options IPV6FIREWALL_DEFAULT_TO_ACCEPT
611 options IPDIVERT #divert sockets
612 options IPFILTER #ipfilter support
613 options IPFILTER_LOG #ipfilter logging
614 options IPFILTER_DEFAULT_BLOCK #block all packets by default
615 options IPSTEALTH #support for stealth forwarding
617 options NS # NETNS support
623 # The MBUF_STRESS_TEST option enables options which create
624 # various random failures / extreme cases related to mbuf
625 # functions. See the mbuf(9) manpage for a list of available
627 options MBUF_STRESS_TEST
629 # Statically link in accept filters
630 options ACCEPT_FILTER_DATA
631 options ACCEPT_FILTER_HTTP
634 # TCP_DROP_SYNFIN adds support for ignoring TCP packets with SYN+FIN. This
635 # prevents nmap et al. from identifying the TCP/IP stack, but breaks support
636 # for RFC1644 extensions and is not recommended for web servers.
638 options TCP_DROP_SYNFIN #drop TCP packets with SYN+FIN
640 # ICMP_BANDLIM enables icmp error response bandwidth limiting. You
641 # typically want this option as it will help protect the machine from
642 # D.O.S. packet attacks.
646 # DUMMYNET enables the "dummynet" bandwidth limiter. You need
647 # IPFIREWALL as well. See the dummynet(4) and ipfw(8) manpages for more info.
648 # When you run DUMMYNET it is advisable to also have "options HZ=1000"
649 # to achieve a smoother scheduling of the traffic.
651 # BRIDGE enables bridging between ethernet cards -- see bridge(4).
652 # You can use IPFIREWALL and DUMMYNET together with bridging.
658 # ATM (HARP version) options
660 # ATM_CORE includes the base ATM functionality code. This must be included
663 # ATM_IP includes support for running IP over ATM.
665 # At least one (and usually only one) of the following signalling managers
666 # must be included (note that all signalling managers include PVC support):
667 # ATM_SIGPVC includes support for the PVC-only signalling manager `sigpvc'.
668 # ATM_SPANS includes support for the `spans' signalling manager, which runs
669 # the FORE Systems's proprietary SPANS signalling protocol.
670 # ATM_UNI includes support for the `uni30' and `uni31' signalling managers,
671 # which run the ATM Forum UNI 3.x signalling protocols.
673 # The `hea' driver provides support for the Efficient Networks, Inc.
674 # ENI-155p ATM PCI Adapter.
676 # The `hfa' driver provides support for the FORE Systems, Inc.
677 # PCA-200E ATM PCI Adapter.
679 options ATM_CORE #core ATM protocol family
680 options ATM_IP #IP over ATM support
681 options ATM_SIGPVC #SIGPVC signalling manager
682 options ATM_SPANS #SPANS signalling manager
683 options ATM_UNI #UNI signalling manager
684 device hea #Efficient ENI-155p ATM PCI
685 device hfa #FORE PCA-200E ATM PCI
687 # DEVICE_POLLING adds support for mixed interrupt-polling handling
688 # of network device drivers, which has significant benefits in terms
689 # of robustness to overloads and responsivity, as well as permitting
690 # accurate scheduling of the CPU time between kernel network processing
691 # and other activities. The drawback is a moderate (up to 1/HZ seconds)
692 # potential increase in response times.
694 # Additionally, you can enable/disable polling at runtime with the
695 # sysctl variable kern.polling.enable (defaults off), set polling
696 # frequency with the sysctl variable kern.polling.pollhz (default 2000,
697 # range 1..30000) and select the CPU fraction reserved to userland with
698 # the sysctl variable kern.polling.user_frac (default 50, range 0..100).
700 # It is strongly recommended to set the sysctl variable kern.polling.pollhz
701 # to 1000 or 2000 as to achieve smoother behaviour.
703 # Only the "dc" "em" "fwe" "fxp" "nge" "nv" "re" "rl" "sis" "vr" and "wi"
704 # devices support this mode of operation at the time of this writing.
706 options DEVICE_POLLING
709 #####################################################################
713 # Only the root, /usr, and /tmp filesystems need be statically
714 # compiled; everything else will be automatically loaded at mount
715 # time. (Exception: the UFS family---FFS, and MFS --- cannot
716 # currently be demand-loaded.) Some people still prefer to statically
717 # compile other filesystems as well.
719 # NB: The NULL, PORTAL, UMAP and UNION filesystems are known to be
720 # buggy, and WILL panic your system if you attempt to do anything with
721 # them. They are included here as an incentive for some enterprising
722 # soul to sit down and fix them.
725 # One of these is mandatory:
726 options FFS #Fast filesystem
727 options MFS #Memory filesystem
728 options NFS #Network filesystem
730 # The rest are optional:
731 #options NFS_NOSERVER #Disable the NFS-server code.
732 options CD9660 #ISO 9660 filesystem
733 options FDESC #File descriptor filesystem
734 options KERNFS #Kernel filesystem
735 options MSDOSFS #MS DOS filesystem
736 options NTFS #NT filesystem
737 # YYY-DR Till we rework the VOP methods for this filesystem
738 #options NULLFS #NULL filesystem
739 options NWFS #NetWare filesystem
740 options PORTAL #Portal filesystem
741 options PROCFS #Process filesystem
742 options SMBFS #SMB/CIFS filesystem
743 options UDF #UDF filesystem
744 # YYY-DR Till we rework the VOP methods for this filesystem
745 #options UMAPFS #UID map filesystem
746 #options UNION #Union filesystem
747 # The xFS_ROOT options REQUIRE the associated ``options xFS''
748 options CD9660_ROOT #CD-ROM usable as root device
749 options FFS_ROOT #FFS usable as root device
750 options NFS_ROOT #NFS usable as root device
752 # Soft updates is technique for improving filesystem speed and
753 # making abrupt shutdown less risky.
756 # Directory hashing improves the speed of operations on very large
757 # directories at the expense of some memory.
760 # Make space in the kernel for a root filesystem on a md device.
761 # Define to the number of kilobytes to reserve for the filesystem.
762 options MD_ROOT_SIZE=10
764 # Make the md device a potential root device, either with preloaded
765 # images of type mfs_root or md_root.
768 # Specify double the default maximum size for malloc(9)-backed md devices.
769 options MD_NSECT=40000
771 # Allow this many swap-devices.
773 # In order to manage swap, the system must reserve bitmap space that
774 # scales with the largest mounted swap device multiplied by NSWAPDEV,
775 # irregardless of whether other swap devices exist or not. So it
776 # is not a good idea to make this value too large.
779 # Disk quotas are supported when this option is enabled.
780 options QUOTA #enable disk quotas
782 # If you are running a machine just as a fileserver for PC and MAC
783 # users, using SAMBA or Netatalk, you may consider setting this option
784 # and keeping all those users' directories on a filesystem that is
785 # mounted with the suiddir option. This gives new files the same
786 # ownership as the directory (similar to group). It's a security hole
787 # if you let these users run programs, so confine it to file-servers
788 # (but it'll save you lots of headaches in those cases). Root owned
789 # directories are exempt and X bits are cleared. The suid bit must be
790 # set on the directory as well; see chmod(1) PC owners can't see/set
791 # ownerships so they keep getting their toes trodden on. This saves
792 # you all the support calls as the filesystem it's used on will act as
793 # they expect: "It's my dir so it must be my file".
798 options NFS_MINATTRTIMO=3 # VREG attrib cache timeout in sec
799 options NFS_MAXATTRTIMO=60
800 options NFS_MINDIRATTRTIMO=30 # VDIR attrib cache timeout in sec
801 options NFS_MAXDIRATTRTIMO=60
802 options NFS_GATHERDELAY=10 # Default write gather delay (msec)
803 options NFS_UIDHASHSIZ=29 # Tune the size of nfssvc_sock with this
804 options NFS_WDELAYHASHSIZ=16 # and with this
805 options NFS_MUIDHASHSIZ=63 # Tune the size of nfsmount with this
806 options NFS_DEBUG # Enable NFS Debugging
809 # YYY-DR Till we rework the VOP methods for this filesystem
810 #options CODA #CODA filesystem.
811 #pseudo-device vcoda 4 #coda minicache <-> venus comm.
814 # Add support for the EXT2FS filesystem of Linux fame. Be a bit
815 # careful with this - the ext2fs code has a tendency to lag behind
816 # changes and not be exercised very much, so mounting read/write could
817 # be dangerous (and even mounting read only could result in panics.)
821 # Use real implementations of the aio_* system calls. There are numerous
822 # stability and security issues in the current aio code that make it
823 # unsuitable for inclusion on machines with untrusted local users.
827 #####################################################################
830 # Real time extensions added in the 1993 Posix
831 # P1003_1B: Infrastructure
832 # _KPOSIX_PRIORITY_SCHEDULING: Build in _POSIX_PRIORITY_SCHEDULING
833 # _KPOSIX_VERSION: Version kernel is built for
836 options _KPOSIX_PRIORITY_SCHEDULING
837 options _KPOSIX_VERSION=199309L
840 #####################################################################
843 # The granularity of operation is controlled by the kernel option HZ whose
844 # default value (100) means a granularity of 10ms (1s/HZ).
845 # Some subsystems, such as DUMMYNET or DEVICE_POLLING, might benefit from
846 # a smaller granularity such as 1ms or less.
847 # Consider, however, that reducing the granularity too much might
848 # cause excessive overhead in clock interrupt processing,
849 # potentially causing ticks to be missed and thus actually reducing
850 # the accuracy of operation.
854 # The following options are used for debugging clock behavior only, and
855 # should not be used for production systems.
857 # CLK_CALIBRATION_LOOP will run the clock calibration loop at startup
858 # until the user presses a key.
860 options CLK_CALIBRATION_LOOP
862 # The following two options measure the frequency of the corresponding
863 # clock relative to the RTC (onboard mc146818a).
865 options CLK_USE_I8254_CALIBRATION
866 options CLK_USE_TSC_CALIBRATION
869 #####################################################################
872 # SCSI DEVICE CONFIGURATION
874 # The SCSI subsystem consists of the `base' SCSI code, a number of
875 # high-level SCSI device `type' drivers, and the low-level host-adapter
876 # device drivers. The host adapters are listed in the ISA and PCI
877 # device configuration sections below.
879 # Beginning with FreeBSD 2.0.5 you can wire down your SCSI devices so
880 # that a given bus, target, and LUN always come on line as the same
881 # device unit. In earlier versions the unit numbers were assigned
882 # in the order that the devices were probed on the SCSI bus. This
883 # means that if you removed a disk drive, you may have had to rewrite
884 # your /etc/fstab file, and also that you had to be careful when adding
885 # a new disk as it may have been probed earlier and moved your device
886 # configuration around.
888 # This old behavior is maintained as the default behavior. The unit
889 # assignment begins with the first non-wired down unit for a device
890 # type. For example, if you wire a disk as "da3" then the first
891 # non-wired disk will be assigned da4.
893 # The syntax for wiring down devices is:
895 # device scbus0 at ahc0 # Single bus device
896 # device scbus1 at ahc1 bus 0 # Single bus device
897 # device scbus3 at ahc2 bus 0 # Twin bus device
898 # device scbus2 at ahc2 bus 1 # Twin bus device
899 # device da0 at scbus0 target 0 unit 0
900 # device da1 at scbus3 target 1
901 # device da2 at scbus2 target 3
902 # device sa1 at scbus1 target 6
905 # "units" (SCSI logical unit number) that are not specified are
906 # treated as if specified as LUN 0.
908 # All SCSI devices allocate as many units as are required.
910 # The "unknown" device (uk? in pre-2.0.5) is now part of the base SCSI
911 # configuration and doesn't have to be explicitly configured.
913 device scbus #base SCSI code
914 device ch #SCSI media changers
915 device da #SCSI direct access devices (aka disks)
916 device sa #SCSI tapes
917 device cd #SCSI CD-ROMs
918 device pass #CAM passthrough driver
919 device pt #SCSI processor type
920 device ses #SCSI SES/SAF-TE driver
924 # -- NOTE -- If you specify one of the bus/target/lun options, you must
926 # CAMDEBUG: When defined enables debugging macros
927 # CAM_DEBUG_BUS: Debug the given bus. Use -1 to debug all busses.
928 # CAM_DEBUG_TARGET: Debug the given target. Use -1 to debug all targets.
929 # CAM_DEBUG_LUN: Debug the given lun. Use -1 to debug all luns.
930 # CAM_DEBUG_FLAGS: OR together CAM_DEBUG_INFO, CAM_DEBUG_TRACE,
931 # CAM_DEBUG_SUBTRACE, and CAM_DEBUG_CDB
933 # CAM_MAX_HIGHPOWER: Maximum number of concurrent high power (start unit) cmds
934 # SCSI_NO_SENSE_STRINGS: When defined disables sense descriptions
935 # SCSI_NO_OP_STRINGS: When defined disables opcode descriptions
936 # SCSI_DELAY: The number of MILLISECONDS to freeze the SIM (scsi adapter)
937 # queue after a bus reset, and the number of milliseconds to
938 # freeze the device queue after a bus device reset.
940 options CAM_DEBUG_BUS=-1
941 options CAM_DEBUG_TARGET=-1
942 options CAM_DEBUG_LUN=-1
943 options CAM_DEBUG_FLAGS="CAM_DEBUG_INFO|CAM_DEBUG_TRACE|CAM_DEBUG_CDB"
944 options CAM_MAX_HIGHPOWER=4
945 options SCSI_NO_SENSE_STRINGS
946 options SCSI_NO_OP_STRINGS
947 options SCSI_DELAY=8000 # Be pessimistic about Joe SCSI device
949 # Options for the CAM CDROM driver:
950 # CHANGER_MIN_BUSY_SECONDS: Guaranteed minimum time quantum for a changer LUN
951 # CHANGER_MAX_BUSY_SECONDS: Maximum time quantum per changer LUN, only
952 # enforced if there is I/O waiting for another LUN
953 # The compiled in defaults for these variables are 2 and 10 seconds,
956 # These can also be changed on the fly with the following sysctl variables:
957 # kern.cam.cd.changer.min_busy_seconds
958 # kern.cam.cd.changer.max_busy_seconds
960 options CHANGER_MIN_BUSY_SECONDS=2
961 options CHANGER_MAX_BUSY_SECONDS=10
963 # Options for the CAM sequential access driver:
964 # SA_IO_TIMEOUT: Timeout for read/write/wfm operations, in minutes
965 # SA_SPACE_TIMEOUT: Timeout for space operations, in minutes
966 # SA_REWIND_TIMEOUT: Timeout for rewind operations, in minutes
967 # SA_ERASE_TIMEOUT: Timeout for erase operations, in minutes
968 # SA_1FM_AT_EOD: Default to model which only has a default one filemark at EOT.
969 options SA_IO_TIMEOUT="(4)"
970 options SA_SPACE_TIMEOUT="(60)"
971 options SA_REWIND_TIMEOUT="(2*60)"
972 options SA_ERASE_TIMEOUT="(4*60)"
973 options SA_1FM_AT_EOD
975 # Optional timeout for the CAM processor target (pt) device
976 # This is specified in seconds. The default is 60 seconds.
977 options SCSI_PT_DEFAULT_TIMEOUT="60"
979 # Optional enable of doing SES passthrough on other devices (e.g., disks)
981 # Normally disabled because a lot of newer SCSI disks report themselves
982 # as having SES capabilities, but this can then clot up attempts to build
983 # build a topology with the SES device that's on the box these drives
985 options SES_ENABLE_PASSTHROUGH
988 #####################################################################
989 # MISCELLANEOUS DEVICES AND OPTIONS
991 # The `pty' device usually turns out to be ``effectively mandatory'',
992 # as it is required for `telnetd', `rlogind', `screen', `emacs', and
993 # `xterm', among others.
995 pseudo-device pty #Pseudo ttys
996 pseudo-device gzip #Exec gzipped a.out's
997 pseudo-device vn #Vnode driver (turns a file into a device)
998 pseudo-device md #Memory/malloc disk
999 pseudo-device snp #Snoop device - to look at pty/vty/etc..
1000 pseudo-device ccd 4 #Concatenated disk driver
1002 # Configuring Vinum into the kernel is not necessary, since the kld
1003 # module gets started automatically when vinum(8) starts. This
1004 # device is also untested. Use at your own risk.
1006 # The option VINUMDEBUG must match the value set in CFLAGS
1007 # in src/sbin/vinum/Makefile. Failure to do so will result in
1008 # the following message from vinum(8):
1010 # Can't get vinum config: Invalid argument
1012 # see vinum(4) for more reasons not to use these options.
1013 pseudo-device vinum #Vinum concat/mirror/raid driver
1014 options VINUMDEBUG #enable Vinum debugging hooks
1016 # Kernel side iconv library
1019 # Size of the kernel message buffer. Should be N * pagesize.
1020 options MSGBUF_SIZE=40960
1023 #####################################################################
1024 # HARDWARE DEVICE CONFIGURATION
1026 # ISA and EISA devices:
1027 # EISA support is available for some device, so they can be auto-probed.
1030 # Mandatory ISA devices: isa, npx
1034 # ISA-PnP BIOS support
1038 # Options for `isa':
1040 # AUTO_EOI_1 enables the `automatic EOI' feature for the master 8259A
1041 # interrupt controller. This saves about 0.7-1.25 usec for each interrupt.
1042 # This option breaks suspend/resume on some portables.
1044 # AUTO_EOI_2 enables the `automatic EOI' feature for the slave 8259A
1045 # interrupt controller. This saves about 0.7-1.25 usec for each interrupt.
1046 # Automatic EOI is documented not to work for for the slave with the
1047 # original i8259A, but it works for some clones and some integrated
1050 # MAXMEM specifies the amount of RAM on the machine; if this is not
1051 # specified, FreeBSD will first read the amount of memory from the CMOS
1052 # RAM, so the amount of memory will initially be limited to 64MB or 16MB
1053 # depending on the BIOS. If the BIOS reports 64MB, a memory probe will
1054 # then attempt to detect the installed amount of RAM. If this probe
1055 # fails to detect >64MB RAM you will have to use the MAXMEM option.
1056 # The amount is in kilobytes, so for a machine with 128MB of RAM, it would
1057 # be 131072 (128 * 1024).
1059 # BROKEN_KEYBOARD_RESET disables the use of the keyboard controller to
1060 # reset the CPU for reboot. This is needed on some systems with broken
1061 # keyboard controllers.
1063 # PAS_JOYSTICK_ENABLE enables the gameport on the ProAudio Spectrum
1065 options COMPAT_OLDISA #FreeBSD 2.2 and 3.x compatibility shims
1068 options MAXMEM="(128*1024)"
1069 #options BROKEN_KEYBOARD_RESET
1070 #options PAS_JOYSTICK_ENABLE
1072 # Enable support for the kernel PLL to use an external PPS signal,
1073 # under supervision of [x]ntpd(8)
1074 # More info in ntpd documentation: http://www.eecis.udel.edu/~ntp
1078 # If you see the "calcru: negative time of %ld usec for pid %d (%s)\n"
1079 # message you probably have some broken sw/hw which disables interrupts
1080 # for too long. You can make the system more resistant to this by
1081 # choosing a high value for NTIMECOUNTER. The default is 5, there
1082 # is no upper limit but more than a couple of hundred are not productive.
1083 # A better strategy may be to sysctl -w kern.timecounter.method=1
1085 options NTIMECOUNTER=20
1087 # The keyboard controller; it controls the keyboard and the PS/2 mouse.
1088 device atkbdc0 at isa? port IO_KBD
1091 device atkbd0 at atkbdc? irq 1
1093 # Options for atkbd:
1094 options ATKBD_DFLT_KEYMAP # specify the built-in keymap
1095 makeoptions ATKBD_DFLT_KEYMAP="jp.106"
1097 # These options are valid for other keyboard drivers as well.
1098 options KBD_DISABLE_KEYMAP_LOAD # refuse to load a keymap
1099 options KBD_INSTALL_CDEV # install a CDEV entry in /dev
1101 # `flags' for atkbd:
1102 # 0x01 Force detection of keyboard, else we always assume a keyboard
1103 # 0x02 Don't reset keyboard, useful for some newer ThinkPads
1104 # 0x03 Force detection and avoid reset, might help with certain
1106 # 0x04 Old-style (XT) keyboard support, useful for older ThinkPads
1109 device psm0 at atkbdc? irq 12
1112 options PSM_HOOKRESUME #hook the system resume event, useful
1114 options PSM_RESETAFTERSUSPEND #reset the device at the resume event
1116 # The video card driver.
1120 # Try the following option if the mouse pointer is not drawn correctly
1121 # or font does not seem to be loaded properly. May cause flicker on
1123 options VGA_ALT_SEQACCESS
1125 # If you can dispense with some vga driver features, you may want to
1126 # use the following options to save some memory.
1127 options VGA_NO_FONT_LOADING # don't save/load font
1128 options VGA_NO_MODE_CHANGE # don't change video modes
1130 # Older video cards may require this option for proper operation.
1131 options VGA_SLOW_IOACCESS # do byte-wide i/o's to TS and GDC regs
1133 # The following option probably won't work with the LCD displays.
1134 options VGA_WIDTH90 # support 90 column modes
1136 # To include support for VESA video modes
1139 # Splash screen at start up! Screen savers require this too.
1140 pseudo-device splash
1142 # The syscons console driver (sco color console compatible).
1144 options MAXCONS=16 # number of virtual consoles
1145 options SC_ALT_MOUSE_IMAGE # simplified mouse cursor in text mode
1146 options SC_DFLT_FONT # compile font in
1147 makeoptions SC_DFLT_FONT=cp850
1148 options SC_DISABLE_DDBKEY # disable `debug' key
1149 options SC_DISABLE_REBOOT # disable reboot key sequence
1150 options SC_HISTORY_SIZE=200 # number of history buffer lines
1151 options SC_MOUSE_CHAR=0x3 # char code for text mode mouse cursor
1152 options SC_PIXEL_MODE # add support for the raster text mode
1154 # The following options will let you change the default colors of syscons.
1155 options SC_NORM_ATTR="(FG_GREEN|BG_BLACK)"
1156 options SC_NORM_REV_ATTR="(FG_YELLOW|BG_GREEN)"
1157 options SC_KERNEL_CONS_ATTR="(FG_RED|BG_BLACK)"
1158 options SC_KERNEL_CONS_REV_ATTR="(FG_BLACK|BG_RED)"
1160 # If you have a two button mouse, you may want to add the following option
1161 # to use the right button of the mouse to paste text.
1162 options SC_TWOBUTTON_MOUSE
1164 # You can selectively disable features in syscons.
1165 options SC_NO_CUTPASTE
1166 options SC_NO_FONT_LOADING
1167 options SC_NO_HISTORY
1168 options SC_NO_SYSMOUSE
1171 # The Numeric Processing eXtension driver. In addition to this, you
1172 # may configure a math emulator (see above). If your machine has a
1173 # hardware FPU and the kernel configuration includes the npx device
1174 # *and* a math emulator compiled into the kernel, the hardware FPU
1175 # will be used, unless it is found to be broken or unless "flags" to
1176 # npx0 includes "0x08", which requests preference for the emulator.
1177 device npx0 at nexus? port IO_NPX flags 0x0 irq 13
1181 # 0x01 don't use the npx registers to optimize bcopy.
1182 # 0x02 don't use the npx registers to optimize bzero.
1183 # 0x04 don't use the npx registers to optimize copyin or copyout.
1184 # 0x08 use emulator even if hardware FPU is available.
1185 # The npx registers are normally used to optimize copying and zeroing when
1186 # all of the following conditions are satisfied:
1187 # I586_CPU is an option
1188 # the cpu is an i586 (perhaps not a Pentium)
1189 # the probe for npx0 succeeds
1190 # INT 16 exception handling works.
1191 # Then copying and zeroing using the npx registers is normally 30-100% faster.
1192 # The flags can be used to control cases where it doesn't work or is slower.
1193 # Setting them at boot time using userconfig works right (the optimizations
1194 # are not used until later in the bootstrap when npx0 is attached).
1195 # Flag 0x08 automatically disables the i586 optimized routines.
1199 # Optional ISA and EISA devices:
1203 # SCSI host adapters: `aha', `aic', `bt'
1205 # adv: All Narrow SCSI bus AdvanSys controllers.
1206 # adw: Second Generation AdvanSys controllers including the ADV940UW.
1208 # ahc: Adaptec 274x/284x/294x
1210 # bt: Most Buslogic controllers
1211 # ncv: NCR 53C500 based SCSI host adapters.
1212 # nsp: Workbit Ninja SCSI-3 based PC Card SCSI host adapters.
1213 # stg: TMC 18C30, 18C50 based ISA/PC Card SCSI host adapters.
1215 # Note that the order is important in order for Buslogic cards to be
1219 device bt0 at isa? port IO_BT0
1226 device stg0 at isa? port 0x140 irq 11
1229 # Adaptec FSA RAID controllers, including integrated DELL controller,
1230 # the Dell PERC 2/QC and the HP NetRAID-4M
1233 device aacp # SCSI Passthrough interface (optional, CAM required)
1236 # Compaq Smart RAID, Mylex DAC960 and AMI MegaRAID controllers. Only
1237 # one entry is needed; the code will find and configure all supported
1240 device ida # Compaq Smart RAID
1241 device mlx # Mylex DAC960
1242 device amr # AMI MegaRAID
1247 device twe # 3ware ATA RAID
1248 device twa # 3ware SATA RAID
1251 # Promise Supertrack SX6000
1261 # The 'ATA' driver supports all ATA and ATAPI devices.
1262 # You only need one "device ata" for it to find all
1263 # PCI ATA/ATAPI devices on modern machines.
1265 device atadisk # ATA disk drives
1266 device atapicd # ATAPI CDROM drives
1267 device atapifd # ATAPI floppy drives
1268 device atapist # ATAPI tape drives
1269 device atapicam # emulate ATAPI devices as SCSI ditto via CAM
1270 # needs CAM to be present (scbus & pass)
1272 #The following options are valid on the ATA driver:
1274 # ATA_STATIC_ID: controller numbering is static (like the old driver)
1275 # else the device numbers are dynamically allocated.
1276 options ATA_STATIC_ID
1279 # For older non-PCI systems, these are the lines to use:
1280 #device ata0 at isa? port IO_WD1 irq 14
1281 #device ata1 at isa? port IO_WD2 irq 15
1284 # Standard floppy disk controllers: `fdc' and `fd'
1286 device fdc0 at isa? port IO_FD1 irq 6 drq 2
1288 # FDC_DEBUG enables floppy debugging. Since the debug output is huge, you
1289 # gotta turn it actually on by setting the variable fd_debug with DDB,
1293 device fd0 at fdc0 drive 0
1294 device fd1 at fdc0 drive 1
1296 # M-systems DiskOnchip products see src/sys/contrib/dev/fla/README
1300 # Other standard PC hardware: `mse', `sio', etc.
1302 # mse: Logitech and ATI InPort bus mouse ports
1303 # sio: serial ports (see sio(4))
1305 device mse0 at isa? port 0x23c irq 5
1307 device sio0 at isa? port IO_COM1 flags 0x10 irq 4
1310 # `flags' for serial drivers that support consoles (only for sio now):
1311 # 0x10 enable console support for this unit. The other console flags
1312 # are ignored unless this is set. Enabling console support does
1313 # not make the unit the preferred console - boot with -h or set
1314 # the 0x20 flag for that. Currently, at most one unit can have
1315 # console support; the first one (in config file order) with
1316 # this flag set is preferred. Setting this flag for sio0 gives
1317 # the old behaviour.
1318 # 0x20 force this unit to be the console (unless there is another
1319 # higher priority console). This replaces the COMCONSOLE option.
1320 # 0x40 reserve this unit for low level console operations. Do not
1321 # access the device in any normal way.
1322 # 0x80 use this port for serial line gdb support in ddb.
1324 # PnP `flags' (set via userconfig using pnp x flags y)
1325 # 0x1 disable probing of this device. Used to prevent your modem
1326 # from being attached as a PnP modem.
1329 # Options for serial drivers that support consoles (only for sio now):
1330 options BREAK_TO_DEBUGGER #a BREAK on a comconsole goes to
1332 options CONSPEED=115200 # speed for serial console
1335 # Solaris implements a new BREAK which is initiated by a character
1336 # sequence CR ~ ^b which is similar to a familiar pattern used on
1337 # Sun servers by the Remote Console.
1338 options ALT_BREAK_TO_DEBUGGER
1341 options COM_ESP #code for Hayes ESP
1342 options COM_MULTIPORT #code for some cards with shared IRQs
1344 # Other flags for sio that aren't documented in the man page.
1345 # 0x20000 enable hardware RTS/CTS and larger FIFOs. Only works for
1346 # ST16650A-compatible UARTs.
1348 # PCI Universal Communications driver
1349 # Supports various single and multi port PCI serial cards. Maybe later
1350 # also the parallel ports on combination serial/parallel cards. New cards
1351 # can be added in src/sys/dev/puc/pucdata.c.
1353 # If the PUC_FASTINTR option is used the driver will try to use fast
1354 # interrupts. The card must then be the only user of that interrupt.
1355 # Interrupts cannot be shared when using PUC_FASTINTR.
1357 options PUC_FASTINTR
1360 # Network interfaces: `cx', `ed', `el', `ep', `ie', `is', `le', `lnc'
1362 # ar: Arnet SYNC/570i hdlc sync 2/4 port V.35/X.21 serial driver (requires sppp)
1363 # cm: Arcnet SMC COM90c26 / SMC COM90c56
1364 # (and SMC COM90c66 in '56 compatibility mode) adapters.
1365 # cs: IBM Etherjet and other Crystal Semi CS89x0-based adapters
1366 # cx: Cronyx/Sigma multiport sync/async (with Cisco or PPP framing)
1367 # ed: Western Digital and SMC 80xx; Novell NE1000 and NE2000; 3Com 3C503
1368 # el: 3Com 3C501 (slow!)
1370 # ex: Intel EtherExpress Pro/10 and other i82595-based adapters
1371 # fe: Fujitsu MB86960A/MB86965A Ethernet
1372 # ie: AT&T StarLAN 10 and EN100; 3Com 3C507; unknown NI5210; Intel EtherExpress
1373 # le: Digital Equipment EtherWorks 2 and EtherWorks 3 (DEPCA, DE100,
1374 # DE101, DE200, DE201, DE202, DE203, DE204, DE205, DE422)
1375 # lnc: Lance/PCnet cards (Isolan, Novell NE2100, NE32-VL, AMD Am7990 & Am79C960)
1376 # rdp: RealTek RTL 8002-based pocket ethernet adapters
1377 # sbni: Granch SBNI12-xx adapters
1378 # sbsh: Granch SBNI16 SHDSL modem PCI adapters
1379 # sr: RISCom/N2 hdlc sync 1/2 port V.35/X.21 serial driver (requires sppp)
1380 # wl: Lucent Wavelan (ISA card only).
1381 # awi: IEEE 802.11b PRISM I cards.
1382 # wi: Lucent WaveLAN/IEEE 802.11 PCMCIA adapters. Note: this supports both
1383 # the PCMCIA and ISA cards: the ISA card is really a PCMCIA to ISA
1384 # bridge with a PCMCIA adapter plugged into it.
1385 # an: Aironet 4500/4800 802.11 wireless adapters. Supports the PCMCIA,
1386 # PCI and ISA varieties.
1387 # xe: Xircom/Intel EtherExpress Pro100/16 PC Card ethernet controller.
1388 # ray: Raytheon Raylink 802.11 wireless NICs, OEM as Webgear Aviator 2.4GHz
1389 # oltr: Olicom ISA token-ring adapters OC-3115, OC-3117, OC-3118 and OC-3133
1390 # (no options needed)
1392 device ar0 at isa? port 0x300 irq 10 iomem 0xd0000
1393 device cm0 at isa? port 0x2e0 irq 9 iomem 0xdc000
1394 device cs0 at isa? port 0x300
1395 device cx0 at isa? port 0x240 irq 15 drq 7
1396 device ed0 at isa? port 0x280 irq 5 iomem 0xd8000
1397 device el0 at isa? port 0x300 irq 9
1400 device fe0 at isa? port 0x300
1401 device ie0 at isa? port 0x300 irq 5 iomem 0xd0000
1402 device ie1 at isa? port 0x360 irq 7 iomem 0xd0000
1403 device le0 at isa? port 0x300 irq 5 iomem 0xd0000
1404 device lnc0 at isa? port 0x280 irq 10 drq 0
1405 device rdp0 at isa? port 0x378 irq 7 flags 2
1406 device sbni0 at isa? port 0x210 irq 5 flags 0xefdead
1407 device sr0 at isa? port 0x300 irq 5 iomem 0xd0000
1408 device sn0 at isa? port 0x300 irq 10
1410 # Wlan support is mandatory for some wireless LAN devices.
1411 device wlan # Wireless LAN support
1412 options WLCACHE # enables the signal-strength cache
1413 options WLDEBUG # enables verbose debugging output
1414 device awi # AMD PCnetMobile
1415 device an # Aironet Communications 4500/4800
1416 device ipw # Intel PRO/Wireless 2100
1417 device iwi # Intel PRO/Wireless 2200BG/2915ABG
1418 device wi # WaveLAN/IEEE, PRISM-II, Spectrum24 802.11DS
1419 device wl0 at isa? port 0x300 # T1 speed ISA/radio lan
1420 device xe # Xircom PCMCIA
1421 device ray # Raytheon Raylink/Webgear Aviator
1423 device oltr0 at isa?
1426 # ATM related options
1428 # The `en' device provides support for Efficient Networks (ENI)
1429 # ENI-155 PCI midway cards, and the Adaptec 155Mbps PCI ATM cards (ANA-59x0).
1431 # atm pseudo-device provides generic atm functions and is required for
1433 # NATM enables the netnatm protocol family that can be used to
1436 # the current driver supports only PVC operations (no atm-arp, no multicast).
1437 # for more details, please read the original documents at
1438 # http://www.ccrc.wustl.edu/pub/chuck/tech/bsdatm/bsdatm.html
1442 options NATM #native ATM
1446 # The flags of the device tells the device a bit more info about the
1447 # device that normally is obtained through the PnP interface.
1448 # bit 2..0 secondary DMA channel;
1449 # bit 4 set if the board uses two dma channels;
1450 # bit 15..8 board type, overrides autodetection; leave it
1451 # zero if don't know what to put in (and you don't,
1452 # since this is unsupported at the moment...).
1454 # This driver will use the new PnP code if it's available. You might
1455 # need PNPBIOS for ISA devices.
1457 # If you have a GUS-MAX card and want to use the CS4231 codec on the
1458 # card the drqs for the gus max must be 8 bit (1, 2, or 3).
1460 # If you would like to use the full duplex option on the gus, then define
1461 # flags to be the ``read dma channel''.
1464 # Basic PCM support, needed for all sound card:
1466 # For PnP/PCI sound cards:
1468 # For non-pnp sound cards:
1469 device snd0 at isa? irq 10 drq 1 flags 0x0
1472 # Miscellaneous hardware:
1474 # mcd: Mitsumi CD-ROM using proprietary (non-ATAPI) interface
1475 # scd: Sony CD-ROM using proprietary (non-ATAPI) interface
1476 # wt: Wangtek and Archive QIC-02/QIC-36 tape drives
1477 # ctx: Cortex-I frame grabber
1478 # apm: Laptop Advanced Power Management (experimental)
1479 # spigot: The Creative Labs Video Spigot video-acquisition board
1480 # meteor: Matrox Meteor video capture board
1481 # bktr: Brooktree bt848/848a/849a/878/879 video capture and TV Tuner board
1482 # cy: Cyclades serial driver
1483 # dgb: Digiboard PC/Xi and PC/Xe series driver (ALPHA QUALITY!)
1484 # dgm: Digiboard PC/Xem driver
1485 # gp: National Instruments AT-GPIB and AT-GPIB/TNT board
1486 # asc: GI1904-based hand scanners, e.g. the Trust Amiscan Grey
1487 # gsc: Genius GS-4500 hand scanner.
1489 # labpc: National Instrument's Lab-PC and Lab-PC+
1490 # rc: RISCom/8 multiport card
1491 # rp: Comtrol Rocketport(ISA) - single card
1492 # tw: TW-523 power line interface for use with X-10 home control products
1493 # si: Specialix SI/XIO 4-32 port terminal multiplexor
1494 # spic: Sony Programmable I/O controller (VAIO notebooks)
1495 # stl: Stallion EasyIO and EasyConnection 8/32 (ISA and PCI), EasyConnection 8/64 PCI
1496 # stli: Stallion EasyConnection 8/64 ISA/EISA, ONboard, Brumby (intelligent)
1497 # nmdm: nullmodem terminal driver (see nmdm(4))
1500 # The flags takes the following meaning for apm0:
1501 # 0x0020 Statclock is broken.
1502 # If apm is omitted, some systems require sysctl -w kern.timecounter.method=1
1503 # for correct timekeeping.
1505 # Notes on the spigot:
1506 # The video spigot is at 0xad6. This port address can not be changed.
1507 # The irq values may only be 10, 11, or 15
1508 # I/O memory is an 8kb region. Possible values are:
1509 # 0a0000, 0a2000, ..., 0fffff, f00000, f02000, ..., ffffff
1510 # The start address must be on an even boundary.
1511 # Add the following option if you want to allow non-root users to be able
1512 # to access the spigot. This option is not secure because it allows users
1513 # direct access to the I/O page.
1514 # options SPIGOT_UNSECURE
1516 # Notes on the Comtrol Rocketport driver:
1518 # The exact values used for rp0 depend on how many boards you have
1519 # in the system. The manufacturer's sample configs are listed as:
1521 # Comtrol Rocketport ISA single card
1522 # device rp0 at isa? port 0x280
1524 # If instead you have two ISA cards, one installed at 0x100 and the
1525 # second installed at 0x180, then you should add the following to
1526 # your kernel configuration file:
1528 # device rp0 at isa? port 0x100
1529 # device rp1 at isa? port 0x180
1531 # For 4 ISA cards, it might be something like this:
1533 # device rp0 at isa? port 0x180
1534 # device rp1 at isa? port 0x100
1535 # device rp2 at isa? port 0x340
1536 # device rp3 at isa? port 0x240
1538 # And for PCI cards, you only need say:
1542 # Notes on the Digiboard driver:
1544 # The following flag values have special meanings:
1545 # 0x01 - alternate layout of pins (dgb & dgm)
1546 # 0x02 - use the windowed PC/Xe in 64K mode (dgb only)
1548 # Notes on the Specialix SI/XIO driver:
1549 # **This is NOT a Specialix supported Driver!**
1550 # The host card is memory, not IO mapped.
1551 # The Rev 1 host cards use a 64K chunk, on a 32K boundary.
1552 # The Rev 2 host cards use a 32K chunk, on a 32K boundary.
1553 # The cards can use an IRQ of 11, 12 or 15.
1555 # Notes on the Stallion stl and stli drivers:
1556 # See src/i386/isa/README.stl for complete instructions.
1557 # This is version 2.0.0, unsupported by Stallion.
1558 # The stl driver has a secondary IO port hard coded at 0x280. You need
1559 # to change src/i386/isa/stallion.c if you reconfigure this on the boards.
1560 # The "flags" and "iosiz" settings on the stli driver depend on the board:
1561 # EasyConnection 8/64 ISA: flags 23 iosiz 0x1000
1562 # EasyConnection 8/64 EISA: flags 24 iosiz 0x10000
1563 # ONboard ISA: flags 4 iosiz 0x10000
1564 # ONboard EISA: flags 7 iosiz 0x10000
1565 # Brumby: flags 2 iosiz 0x4000
1566 # Stallion: flags 1 iosiz 0x10000
1567 # For the PCI cards, "device stl" will suffice.
1569 device mcd0 at isa? port 0x300 irq 10
1570 # for the Sony CDU31/33A CDROM
1571 device scd0 at isa? port 0x230
1572 # for the SoundBlaster 16 multicd - up to 4 devices
1573 device wt0 at isa? port 0x300 irq 5 drq 1
1574 device ctx0 at isa? port 0x230 iomem 0xd0000
1575 device spigot0 at isa? port 0xad6 irq 15 iomem 0xee000
1577 device gp0 at isa? port 0x2c0
1578 device gsc0 at isa? port IO_GSC1 drq 3
1579 device joy0 at isa? port IO_GAME
1580 device cy0 at isa? irq 10 iomem 0xd4000 iosiz 0x2000
1581 options CY_PCI_FASTINTR # Use with cy_pci unless irq is shared
1582 #device dgb0 at isa? port 0x220 iomem 0xfc000
1583 #options NDGBPORTS=16 # Defaults to 16*NDGB
1584 device dgm0 at isa? port 0x104 iomem 0xd0000
1585 device labpc0 at isa? port 0x260 irq 5
1586 device rc0 at isa? port 0x220 irq 12
1588 #device rp0 at isa? port 0x280
1589 # the port and irq for tw0 are fictitious
1590 device tw0 at isa? port 0x380 irq 11
1591 device si0 at isa? iomem 0xd0000 irq 12
1592 device asc0 at isa? port IO_ASC1 drq 3 irq 10
1593 device spic0 at isa? irq 0 port 0x10a0
1594 device stl0 at isa? port 0x2a0 irq 10
1595 device stli0 at isa? port 0x2a0 iomem 0xcc000 flags 23 iosiz 0x1000
1596 # HOT1 Xilinx 6200 card (http://www.vcc.com/)
1598 # nullmodem terminal driver
1604 # The EISA bus device is `eisa'. It provides auto-detection and
1605 # configuration support for all devices on the EISA bus.
1607 # The `ahb' device provides support for the Adaptec 174X adapter.
1609 # The `ahc' device provides support for the Adaptec 274X and 284X
1610 # adapters. The 284X, although a VLB card, responds to EISA probes.
1612 # fea: DEC DEFEA EISA FDDI adapter
1619 # The aic7xxx driver will attempt to use memory mapped I/O for all PCI
1620 # controllers that have it configured only if this option is set. Unfortunately,
1621 # this doesn't work on some motherboards, which prevents it from being the
1623 options AHC_ALLOW_MEMIO
1625 # The adw driver will attempt to use memory mapped I/O for all PCI
1626 # controllers that have it configured only if this option is set.
1627 options ADW_ALLOW_MEMIO
1629 # By default, only 10 EISA slots are probed, since the slot numbers
1630 # above clash with the configuration address space of the PCI subsystem,
1631 # and the EISA probe is not very smart about this. This is sufficient
1632 # for most machines, but in particular the HP NetServer LC series comes
1633 # with an onboard AIC7770 dual-channel SCSI controller on EISA slot #11,
1634 # thus you need to bump this figure to 12 for them.
1635 options EISA_SLOTS=12
1638 # PCI devices & PCI options:
1640 # The main PCI bus device is `pci'. It provides auto-detection and
1641 # configuration support for all devices on the PCI bus, using either
1642 # configuration mode defined in the PCI specification.
1648 #Enable pci resources left off by a "lazy" BIOS.
1650 #WARNING! PCI_ENABLE_IO_MODES IS A VERY DANGEROUS OPTION AND MANY
1651 #SYSTEMS WILL EXPERIENCE INSTABILITY WITH IT ON. USE ONLY AS A LAST
1654 options PCI_ENABLE_IO_MODES
1655 #options PCI_QUIET #quiets PCI code on chipset settings
1656 options COMPAT_OLDPCI #FreeBSD 2.2 and 3.x compatibility shims
1663 # The `ahc' device provides support for the Adaptec 29/3940(U)(W)
1664 # and motherboard based AIC7870/AIC7880 adapters.
1666 # The 'ahd' device provides support for the Adaptec 79xx Ultra320
1667 # SCSI adapters. Options are documented in the ahd(4) manpage:
1669 options AHD_DEBUG_OPTS=0xffffffff
1670 options AHD_REG_PRETTY_PRINT
1671 #options AHD_TMODE_ENABLE=0xff
1673 # The `amd' device provides support for the AMD 53C974 SCSI host
1674 # adapter chip as found on devices such as the Tekram DC-390(T).
1676 # The `bge' device provides support for gigabit ethernet adapters
1677 # based on the Broadcom BCM570x familiy of controllers, including the
1678 # 3Com 3c996-T, the Netgear GA302T, the SysKonnect SK-9D21 and SK-9D41,
1679 # and the embedded gigE NICs on Dell PowerEdge 2550 servers.
1681 # options BGE_FAKE_AUTONEG is needed for some IBM blade servers with the
1682 # DNL switch module. Auto negotiation is broken those configurations.
1684 # The `ncr' device provides support for the NCR 53C810 and 53C825
1685 # self-contained SCSI host adapters.
1687 # The `isp' device provides support for the Qlogic ISP 1020, 1040
1688 # nd 1040B PCI SCSI host adapters, ISP 1240 Dual Ultra SCSI,
1689 # ISP 1080 and 1280 (Dual) Ultra2, ISP 12160 Ultra3 SCSI, as well as
1690 # the Qlogic ISP 2100 and ISP 2200 Fibre Channel Host Adapters.
1692 # The `dc' device provides support for PCI fast ethernet adapters
1693 # based on the DEC/Intel 21143 and various workalikes including:
1694 # the ADMtek AL981 Comet and AN985 Centaur, the ASIX Electronics
1695 # AX88140A and AX88141, the Davicom DM9100 and DM9102, the Lite-On
1696 # 82c168 and 82c169 PNIC, the Lite-On/Macronix LC82C115 PNIC II
1697 # and the Macronix 98713/98713A/98715/98715A/98725 PMAC. This driver
1698 # replaces the old al, ax, dm, pn and mx drivers. List of brands:
1699 # Digital DE500-BA, Kingston KNE100TX, D-Link DFE-570TX, SOHOware SFA110,
1700 # SVEC PN102-TX, CNet Pro110B, 120A, and 120B, Compex RL100-TX,
1701 # LinkSys LNE100TX, LNE100TX V2.0, Jaton XpressNet, Alfa Inc GFC2204,
1704 # The `de' device provides support for the Digital Equipment DC21040
1705 # self-contained Ethernet adapter.
1707 # The `em' device provides support for the Intel Pro/1000 Family of Gigabit
1708 # adapters (82542, 82543, 82544, 82540).
1710 # The `fxp' device provides support for the Intel EtherExpress Pro/100B
1711 # PCI Fast Ethernet adapters.
1713 # The `gx' device provides support for the Intel Pro/1000 Gigabit Ethernet
1714 # PCI adapters (82542, 82543-F, 82543-T).
1716 # The 'lge' device provides support for PCI gigabit ethernet adapters
1717 # based on the Level 1 LXT1001 NetCellerator chipset. This includes the
1718 # D-Link DGE-500SX, SMC TigerCard 1000 (SMC9462SX), and some Addtron cards.
1720 # The 'my' device provides support for the Myson MTD80X and MTD89X PCI
1721 # Fast Ethernet adapters.
1723 # The 'nge' device provides support for PCI gigabit ethernet adapters
1724 # based on the National Semiconductor DP83820 and DP83821 chipset. This
1725 # includes the SMC EZ Card 1000 (SMC9462TX), D-Link DGE-500T, Asante
1726 # FriendlyNet GigaNIX 1000TA and 1000TPC, the Addtron AEG320T, the
1727 # LinkSys EG1032 and EG1064, the Surecom EP-320G-TX and the Netgear GA622T.
1729 # The 'pcn' device provides support for PCI fast ethernet adapters based
1730 # on the AMD Am79c97x chipsets, including the PCnet/FAST, PCnet/FAST+,
1731 # PCnet/PRO and PCnet/Home. These were previously handled by the lnc
1732 # driver (and still will be if you leave this driver out of the kernel).
1734 # Te 're' device provides support for PCI GigaBit ethernet adapters based
1735 # on the RealTek 8169 chipset. It also supports the 8139C+ and is the
1736 # prefered driver for that chip.
1738 # The 'rl' device provides support for PCI fast ethernet adapters based
1739 # on the RealTek 8129/8139 chipset. Note that the RealTek driver defaults
1740 # to using programmed I/O to do register accesses because memory mapped
1741 # mode seems to cause severe lockups on SMP hardware. This driver also
1742 # supports the Accton EN1207D `Cheetah' adapter, which uses a chip called
1743 # the MPX 5030/5038, which is either a RealTek in disguise or a RealTek
1744 # workalike. Note that the D-Link DFE-530TX+ uses the RealTek chipset
1745 # and is supported by this driver, not the 'vr' driver.
1747 # The 'sf' device provides support for Adaptec Duralink PCI fast
1748 # ethernet adapters based on the Adaptec AIC-6915 "starfire" controller.
1749 # This includes dual and quad port cards, as well as one 100baseFX card.
1750 # Most of these are 64-bit PCI devices, except for one single port
1751 # card which is 32-bit.
1753 # The 'ste' device provides support for adapters based on the Sundance
1754 # Technologies ST201 PCI fast ethernet controller. This includes the
1757 # The 'sis' device provides support for adapters based on the Silicon
1758 # Integrated Systems SiS 900 and SiS 7016 PCI fast ethernet controller
1761 # The 'sk' device provides support for the SysKonnect SK-984x series
1762 # PCI gigabit ethernet NICs. This includes the SK-9841 and SK-9842
1763 # single port cards (single mode and multimode fiber) and the
1764 # SK-9843 and SK-9844 dual port cards (also single mode and multimode).
1765 # The driver will autodetect the number of ports on the card and
1766 # attach each one as a separate network interface.
1768 # The 'ti' device provides support for PCI gigabit ethernet NICs based
1769 # on the Alteon Networks Tigon 1 and Tigon 2 chipsets. This includes the
1770 # Alteon AceNIC, the 3Com 3c985, the Netgear GA620 and various others.
1771 # Note that you will probably want to bump up NMBCLUSTERS a lot to use
1774 # The 'tl' device provides support for the Texas Instruments TNETE100
1775 # series 'ThunderLAN' cards and integrated ethernet controllers. This
1776 # includes several Compaq Netelligent 10/100 cards and the built-in
1777 # ethernet controllers in several Compaq Prosignia, Proliant and
1778 # Deskpro systems. It also supports several Olicom 10Mbps and 10/100
1781 # The `tx' device provides support for the SMC 9432 TX, BTX and FTX cards.
1783 # The `txp' device provides support for the 3Com 3cR990 "Typhoon"
1786 # The `vr' device provides support for various fast ethernet adapters
1787 # based on the VIA Technologies VT3043 `Rhine I' and VT86C100A `Rhine II'
1788 # chips, including the D-Link DFE530TX (see 'rl' for DFE530TX+), the Hawking
1789 # Technologies PN102TX, and the AOpen/Acer ALN-320.
1791 # The `vx' device provides support for the 3Com 3C590 and 3C595
1794 # The `wb' device provides support for various fast ethernet adapters
1795 # based on the Winbond W89C840F chip. Note: this is not the same as
1796 # the Winbond W89C940F, which is an NE2000 clone.
1798 # The `xl' device provides support for the 3Com 3c900, 3c905 and
1799 # 3c905B (Fast) Etherlink XL cards and integrated controllers. This
1800 # includes the integrated 3c905B-TX chips in certain Dell Optiplex and
1801 # Dell Precision desktop machines and the integrated 3c905-TX chips
1802 # in Dell Latitude laptop docking stations.
1804 # The `fpa' device provides support for the Digital DEFPA PCI FDDI
1805 # adapter. pseudo-device fddi is also needed.
1807 # The `meteor' device is a PCI video capture board. It can also have the
1808 # following options:
1809 # options METEOR_ALLOC_PAGES=xxx preallocate kernel pages for data entry
1810 # figure (ROWS*COLUMN*BYTES_PER_PIXEL*FRAME+PAGE_SIZE-1)/PAGE_SIZE
1811 # options METEOR_DEALLOC_PAGES remove all allocated pages on close(2)
1812 # options METEOR_DEALLOC_ABOVE=xxx remove all allocated pages above the
1813 # specified amount. If this value is below the allocated amount no action
1815 # options METEOR_SYSTEM_DEFAULT={METEOR_PAL|METEOR_NTSC|METEOR_SECAM}, used
1816 # for initialization of fps routine when a signal is not present.
1818 # The 'bktr' device is a PCI video capture device using the Brooktree
1819 # bt848/bt848a/bt849a/bt878/bt879 chipset. When used with a TV Tuner it forms a
1820 # TV card, eg Miro PC/TV, Hauppauge WinCast/TV WinTV, VideoLogic Captivator,
1821 # Intel Smart Video III, AverMedia, IMS Turbo, FlyVideo.
1823 # options OVERRIDE_CARD=xxx
1824 # options OVERRIDE_TUNER=xxx
1825 # options OVERRIDE_MSP=1
1826 # options OVERRIDE_DBX=1
1827 # These options can be used to override the auto detection
1828 # The current values for xxx are found in src/sys/dev/bktr/bktr_card.h
1829 # Using sysctl(8) run-time overrides on a per-card basis can be made
1831 # options BROOKTREE_SYSTEM_DEFAULT=BROOKTREE_PAL
1833 # options BROOKTREE_SYSTEM_DEFAULT=BROOKTREE_NTSC
1834 # Specifes the default video capture mode.
1835 # This is required for Dual Crystal (28&35Mhz) boards where PAL is used
1836 # to prevent hangs during initialisation. eg VideoLogic Captivator PCI.
1838 # options BKTR_USE_PLL
1839 # PAL or SECAM users who have a 28Mhz crystal (and no 35Mhz crystal)
1840 # must enable PLL mode with this option. eg some new Bt878 cards.
1842 # options BKTR_GPIO_ACCESS
1843 # This enable IOCTLs which give user level access to the GPIO port.
1845 # options BKTR_NO_MSP_RESET
1846 # Prevents the MSP34xx reset. Good if you initialise the MSP in another OS first
1848 # options BKTR_430_FX_MODE
1849 # Switch Bt878/879 cards into Intel 430FX chipset compatibility mode.
1851 # options BKTR_SIS_VIA_MODE
1852 # Switch Bt878/879 cards into SIS/VIA chipset compatibility mode which is
1853 # needed for some old SiS and VIA chipset motherboards.
1854 # This also allows Bt878/879 chips to work on old OPTi (<1997) chipset
1855 # motherboards and motherboards with bad or incomplete PCI 2.1 support.
1856 # As a rough guess, old = before 1998
1858 # options BKTR_NEW_MSP34XX_DRIVER
1859 # Use new, more complete initialization scheme for the msp34* soundchip.
1860 # Should fix stereo autodetection if the old driver does only output
1864 # The oltr driver supports the following Olicom PCI token-ring adapters
1865 # OC-3136, OC-3137, OC-3139, OC-3140, OC-3141, OC-3540, OC-3250
1867 device ahc # AHA2940 and onboard AIC7xxx devices
1868 device ahd # AIC79xx devices
1869 device amd # AMD 53C974 (Tekram DC-390(T))
1870 device isp # Qlogic family
1871 device ispfw # Firmware for QLogic HBAs
1872 device mpt # LSI '909 FC adapters
1873 device ncr # NCR/Symbios Logic
1874 device sym # NCR/Symbios Logic (newer chipsets)
1875 device trm # Tekram DC395U/UW/F and DC315U
1879 # ISP_TARGET_MODE - enable target mode operation
1880 #options ISP_TARGET_MODE=1
1882 # Options used in dev/sym/ (Symbios SCSI driver).
1883 #options SYM_SETUP_LP_PROBE_MAP #-Low Priority Probe Map (bits)
1884 # Allows the ncr to take precedence
1885 # 1 (1<<0) -> 810a, 860
1886 # 2 (1<<1) -> 825a, 875, 885, 895
1887 # 4 (1<<2) -> 895a, 896, 1510d
1888 #options SYM_SETUP_SCSI_DIFF #-HVD support for 825a, 875, 885
1889 # disabled:0 (default), enabled:1
1890 #options SYM_SETUP_PCI_PARITY #-PCI parity checking
1891 # disabled:0, enabled:1 (default)
1892 #options SYM_SETUP_MAX_LUN #-Number of LUNs supported
1893 # default:8, range:[1..64]
1896 # MII bus support is required for some PCI 10/100 ethernet NICs,
1897 # namely those which use MII-compliant transceivers or implement
1898 # tranceiver control interfaces that operate like an MII. Adding
1899 # "device miibus0" to the kernel config pulls in support for
1900 # the generic miibus API and all of the PHY drivers, including a
1901 # generic one for PHYs that aren't specifically handled by an
1902 # individual driver.
1905 # PCI Ethernet NICs that use the common MII bus controller code.
1906 device bfe # Broadcom BCM440x 10/100 Ethernet
1907 device dc # DEC/Intel 21143 and various workalikes
1908 device fxp # Intel EtherExpress PRO/100B (82557, 82558)
1909 device my # Myson Fast Ethernet (MTD80X, MTD89X)
1910 device pcn # AMD Am79C97x PCI 10/100 NICs
1911 device re # RealTek 8139C+/8169
1912 device rl # RealTek 8129/8139
1913 device sbsh # Granch SBNI16 SHDSL modem
1914 device sf # Adaptec AIC-6915 (``Starfire'')
1915 device sis # Silicon Integrated Systems SiS 900/SiS 7016
1916 device ste # Sundance ST201 (D-Link DFE-550TX)
1917 device tl # Texas Instruments ThunderLAN
1918 device tx # SMC EtherPower II (83c17x ``EPIC'')
1919 device vr # VIA Rhine, Rhine II
1920 device wb # Winbond W89C840F
1921 device xl # 3Com 3c90x (``Boomerang'', ``Cyclone'')
1923 # PCI Ethernet NICs.
1924 device de # DEC/Intel DC21x4x (``Tulip'')
1925 device txp # 3Com 3cR990 (``Typhoon'')
1926 device vx # 3Com 3c590, 3c595 (``Vortex'')
1928 # Gigabit Ethernet NICs.
1929 device bge # Broadcom BCM570x (``Tigon III'')
1930 device em # Intel Pro/1000 (82542,82543,82544,82540)
1931 device gx # Intel Pro/1000 (82542, 82543)
1932 device lge # Level 1 LXT1001 (``Mercury'')
1933 device nge # NatSemi DP83820 and DP83821
1934 device sk # SysKonnect GEnesis, LinkSys EG1023, D-Link
1935 device ti # Alteon (``Tigon I'', ``Tigon II'')
1940 #The oltr driver in the ISA section will also find PCI cards.
1944 # Brooktree driver has been ported to the new I2C framework. Thus,
1945 # you'll need to have the following 3 lines in the kernel config.
1949 # The iic and smb devices are only needed if you want to control other
1950 # I2C slaves connected to the external connector of some cards.
1953 options BKTR_NEW_MSP34XX_DRIVER
1958 # pccard: pccard slots
1959 # cardbus/cbb: cardbus bridge
1965 # Laptop/Notebook options:
1968 # apm under `Miscellaneous hardware'
1971 # For older notebooks that signal a powerfail condition (external
1972 # power supply dropped, or battery state low) by issuing an NMI:
1974 options POWERFAIL_NMI # make it beep instead of panicing
1979 # System Management Bus support is provided by the 'smbus' device.
1980 # Access to the SMBus device is via the 'smb' device (/dev/smb*),
1981 # which is a child of the 'smbus' device.
1983 # Supported devices:
1984 # smb standard io through /dev/smb*
1986 # Supported SMB interfaces:
1987 # iicsmb I2C to SMB bridge with any iicbus interface
1988 # bktr brooktree848 I2C hardware interface
1989 # intpm Intel PIIX4 (82371AB, 82443MX) Power Management Unit
1990 # alpm Acer Aladdin-IV/V/Pro2 Power Management Unit
1991 # ichsmb Intel ICH SMBus controller chips (82801AA, 82801AB, 82801BA)
1992 # viapm VIA VT82C586B,596,686A and VT8233 SMBus controllers
1993 # amdpm AMD 756 Power Management Unit
1995 device smbus # Bus support, required for smb below.
2008 # Philips i2c bus support is provided by the `iicbus' device.
2010 # Supported devices:
2011 # ic i2c network interface
2012 # iic i2c standard io
2013 # iicsmb i2c to smb bridge. Allow i2c i/o with smb commands.
2015 # Supported interfaces:
2016 # pcf Philips PCF8584 ISA-bus controller
2017 # bktr brooktree848 I2C software interface
2020 # iicbb generic I2C bit-banging code (needed by lpbb, bktr)
2022 device iicbus # Bus support, required for ic/iic/iicsmb below.
2027 device iicsmb # smb over i2c bridge
2029 device pcf0 at isa? port 0x320 irq 5
2031 #---------------------------------------------------------------------------
2034 # See /usr/share/examples/isdn/ROADMAP for an introduction to isdn4bsd.
2036 # i4b passive ISDN cards support contains the following hardware drivers:
2038 # isic - Siemens/Infineon ISDN ISAC/HSCX/IPAC chipset driver
2039 # iwic - Winbond W6692 PCI bus ISDN S/T interface controller
2040 # ifpi - AVM Fritz!Card PCI driver
2041 # ifpi2 - AVM Fritz!Card PCI driver Version 2
2042 # ihfc - Cologne Chip HFC ISA/ISA-PnP chipset driver
2043 # ifpnp - AVM Fritz!Card PnP driver
2044 # itjc - Siemens ISAC / TJNet Tiger300/320 chipset
2046 # i4b active ISDN cards support contains the following hardware drivers:
2048 # iavc - AVM B1 PCI, AVM B1 ISA, AVM T1
2050 # Note that the ``options'' (if given) and ``device'' lines must BOTH
2051 # be uncommented to enable support for a given card !
2053 # In addition to a hardware driver (and probably an option) the mandatory
2054 # ISDN protocol stack devices and the mandatory support device must be
2055 # enabled as well as one or more devices from the optional devices section.
2057 #---------------------------------------------------------------------------
2058 # isic driver (Siemens/Infineon chipsets)
2059 #---------------------------------------------------------------------------
2061 # ISA bus non-PnP Cards:
2062 # ----------------------
2064 # Teles S0/8 or Niccy 1008
2066 device isic0 at isa? iomem 0xd0000 irq 5 flags 1
2068 # Teles S0/16 or Creatix ISDN-S0 or Niccy 1016
2070 #device isic0 at isa? port 0xd80 iomem 0xd0000 irq 5 flags 2
2074 #device isic0 at isa? port 0xd80 irq 5 flags 3
2076 # AVM A1 or AVM Fritz!Card
2078 #device isic0 at isa? port 0x340 irq 5 flags 4
2080 # USRobotics Sportster ISDN TA intern
2082 #device isic0 at isa? port 0x268 irq 5 flags 7
2084 # ITK ix1 Micro ( < V.3, non-PnP version )
2086 #device isic0 at isa? port 0x398 irq 10 flags 18
2090 #device isic0 at isa? port 0x360 irq 10 flags 20
2092 # ISA bus PnP Cards:
2093 # ------------------
2096 options TEL_S0_16_3_P
2099 # Creatix ISDN-S0 P&P
2103 # Dr. Neuhaus Niccy Go@
2107 # Sedlbauer Win Speed
2115 # ELSA QuickStep 1000pro ISA
2119 # ITK ix1 Micro ( V.3, PnP version )
2123 # Siemens I-Surf 2.0
2124 options SIEMENS_ISURF2
2127 # Asuscom ISDNlink 128K ISAC
2128 options ASUSCOM_IPAC
2131 # Eicon Diehl DIVA 2.0 and 2.02
2138 # ELSA MicroLink ISDN/PCI (same as ELSA QuickStep 1000pro PCI)
2142 #---------------------------------------------------------------------------
2143 # ifpnp driver for AVM Fritz!Card ISA PnP
2144 #---------------------------------------------------------------------------
2146 # AVM Fritz!Card ISA PnP
2149 #---------------------------------------------------------------------------
2150 # ihfc driver for Cologne Chip ISA chipsets (experimental!)
2151 #---------------------------------------------------------------------------
2153 # Teles 16.3c ISA PnP
2154 # AcerISDN P10 ISA PnP
2155 # TELEINT ISDN SPEED No.1
2158 #---------------------------------------------------------------------------
2159 # ifpi driver for AVM Fritz!Card PCI 1.0 (2.0 unsupported!)
2160 #---------------------------------------------------------------------------
2162 # AVM Fritz!Card PCI 1.0
2165 #---------------------------------------------------------------------------
2166 # ifpi2 driver for AVM Fritz!Card PCI 2.0
2167 #---------------------------------------------------------------------------
2169 # AVM Fritz!Card PCI 2.0
2172 #---------------------------------------------------------------------------
2173 # iwic driver for Winbond W6692 chipset
2174 #---------------------------------------------------------------------------
2176 # ASUSCOM P-IN100-ST-D (and other Winbond W6692 based cards)
2179 #---------------------------------------------------------------------------
2180 # itjc driver for Simens ISAC / TJNet Tiger300/320 chipset
2181 #---------------------------------------------------------------------------
2183 # Traverse Technologies NETjet-S
2187 #---------------------------------------------------------------------------
2188 # iavc driver (AVM active cards, needs i4bcapi driver!)
2189 #---------------------------------------------------------------------------
2191 pseudo-device "i4bcapi" 2
2196 # AVM B1 ISA bus (PnP mode not supported!)
2197 #device iavc0 at isa? port 0x150 irq 5
2200 # ISDN Protocol Stack (mandatory)
2201 # -------------------------------
2203 # Q.921 / layer 2 - i4b passive cards D channel handling
2204 pseudo-device "i4bq921"
2206 # Q.931 / layer 3 - i4b passive cards D channel handling
2207 pseudo-device "i4bq931"
2209 # layer 4 - i4b common passive and active card handling
2215 # userland driver to do ISDN tracing (for passive cards only)
2216 pseudo-device "i4btrc" 4
2218 # userland driver to control the whole thing (mandatory)
2219 pseudo-device "i4bctl"
2221 # userland driver for access to raw B channel
2222 pseudo-device "i4brbch" 4
2224 # userland driver for telephony
2225 pseudo-device "i4btel" 2
2227 # network driver for IP over raw HDLC ISDN
2228 pseudo-device "i4bipr" 4
2229 # enable VJ header compression detection for ipr i/f
2231 # enable logging of the first n IP packets to isdnd (n=32 here)
2234 # network driver for sync PPP over ISDN - requires sppp
2235 pseudo-device "i4bisppp" 4
2240 # Parallel port bus support is provided by the `ppbus' device.
2241 # Multiple devices may be attached to the parallel port, devices
2242 # are automatically probed and attached when found.
2244 # Supported devices:
2245 # vpo Iomega Zip Drive
2246 # Requires SCSI disk support ('scbus' and 'da'); the best
2247 # performance is achieved with ports in EPP 1.9 mode.
2248 # lpt Parallel Printer
2249 # plip Parallel network interface
2250 # ppi General-purpose I/O ("Geek Port") + IEEE1284 I/O
2251 # pps Pulse per second Timing Interface
2252 # lpbb Philips official parallel port I2C bit-banging interface
2254 # Supported interfaces:
2255 # ppc ISA-bus parallel port interfaces.
2258 options PPC_PROBE_CHIPSET # Enable chipset specific detection
2259 # (see flags in ppc(4))
2260 options DEBUG_1284 # IEEE1284 signaling protocol debug
2261 options PERIPH_1284 # Makes your computer act as a IEEE1284
2262 # compliant peripheral
2263 options DONTPROBE_1284 # Avoid boot detection of PnP parallel devices
2264 options VP0_DEBUG # ZIP/ZIP+ debug
2265 options LPT_DEBUG # Printer driver debug
2266 options PPC_DEBUG # Parallel chipset level debug
2267 options PLIP_DEBUG # Parallel network IP interface debug
2268 options PCFCLOCK_VERBOSE # Verbose pcfclock driver
2269 options PCFCLOCK_MAX_RETRIES=5 # Maximum read tries (default 10)
2271 device ppc0 at isa? irq 7
2281 # Kernel BOOTP support
2283 options BOOTP # Use BOOTP to obtain IP address/hostname
2284 options BOOTP_NFSROOT # NFS mount root filesystem using BOOTP info
2285 options BOOTP_NFSV3 # Use NFS v3 to NFS mount root
2286 options BOOTP_COMPAT # Workaround for broken bootp daemons.
2287 options BOOTP_WIRED_TO=fxp0 # Use interface fxp0 for BOOTP
2290 # Add tie-ins for a hardware watchdog. This only enable the hooks;
2291 # the user must still supply the actual driver.
2296 # Set the number of PV entries per process. Increasing this can
2297 # stop panics related to heavy use of shared memory. However, that can
2298 # (combined with large amounts of physical memory) cause panics at
2299 # boot time due the kernel running out of VM space.
2301 # If you're tweaking this, you might also want to increase the sysctls
2302 # "vm.v_free_min", "vm.v_free_reserved", and "vm.v_free_target".
2304 # The value below is the one more than the default.
2306 options PMAP_SHPGPERPROC=201
2309 # Change the size of the kernel virtual address space. Due to
2310 # constraints in loader(8) on i386, this must be a multiple of 4.
2311 # 256 = 1 GB of kernel address space. Increasing this also causes
2312 # a reduction of the address space in user processes. 512 splits
2313 # the 4GB cpu address space in half (2GB user, 2GB kernel).
2315 options KVA_PAGES=260
2318 # Disable swapping. This option removes all code which actually performs
2319 # swapping, so it's not possible to turn it back on at run-time.
2321 # This is sometimes usable for systems which don't have any swap space
2322 # (see also sysctls "vm.defer_swapspace_pageouts" and
2323 # "vm.disable_swapspace_pageouts")
2325 #options NO_SWAPPING
2327 # Set the number of sf_bufs to allocate. sf_bufs are virtual buffers
2328 # for sendfile(2) that are used to map file VM pages, and normally
2329 # default to a quantity that is roughly 16*MAXUSERS+512. You would
2330 # typically want about 4 of these for each simultaneous file send.
2332 options NSFBUFS=1024
2334 # Set the size of the buffer cache KVM reservation, in buffers. This is
2335 # scaled by approximately 16384 bytes. The system will auto-size the buffer
2336 # cache if this option is not specified.
2340 # Set the size of the mbuf KVM reservation, in clusters. This is scaled
2341 # by approximately 2048 bytes. The system will auto-size the mbuf area
2342 # to (512 + maxusers*16) if this option is not specified.
2343 # maxusers is in turn computed at boot time depending on available memory
2344 # or set to the value specified by "options MAXUSERS=x" (x=0 means
2346 # So, to take advantage of autoscaling, you have to remove both
2347 # NMBCLUSTERS and MAXUSERS (and NMBUFS) from your kernel config.
2349 options NMBCLUSTERS=1024
2351 # Set the number of mbufs available in the system. Each mbuf
2352 # consumes 256 bytes. The system will autosize this (to 4 times
2353 # the number of NMBCLUSTERS, depending on other constraints)
2354 # if this option is not specified.
2358 # Tune the kernel malloc area parameters. VM_KMEM_SIZE represents the
2359 # minimum, in bytes, and is typically (12*1024*1024) (12MB).
2360 # VM_KMEM_SIZE_MAX represents the maximum, typically 200 megabytes.
2361 # VM_KMEM_SIZE_SCALE can be set to adjust the auto-tuning factor, which
2362 # typically defaults to 4 (kernel malloc area size is physical memory
2363 # divided by the scale factor).
2365 options VM_KMEM_SIZE="(10*1024*1024)"
2366 options VM_KMEM_SIZE_MAX="(100*1024*1024)"
2367 options VM_KMEM_SIZE_SCALE="4"
2369 # Tune the buffer cache maximum KVA reservation, in bytes. The maximum is
2370 # usually capped at 200 MB, effecting machines with > 1GB of ram. Note
2371 # that the buffer cache only really governs write buffering and disk block
2372 # translations. The VM page cache is our primary disk cache and is not
2373 # effected by the size of the buffer cache.
2375 options VM_BCACHE_SIZE_MAX="(100*1024*1024)"
2377 # Tune the swap zone KVA reservation, in bytes. The default is typically
2378 # 70 MB, giving the system the ability to manage a maximum of 28GB worth
2379 # of swapped out data.
2381 options VM_SWZONE_SIZE_MAX="(50*1024*1024)"
2384 # Enable extra debugging code for locks. This stores the filename and
2385 # line of whatever acquired the lock in the lock itself, and change a
2386 # number of function calls to pass around the relevant data. This is
2387 # not at all useful unless you are debugging lock code. Also note
2388 # that it is likely to break e.g. fstat(1) unless you recompile your
2389 # userland with -DDEBUG_LOCKS as well.
2393 # Set the amount of time (in seconds) the system will wait before
2394 # rebooting automatically when a kernel panic occurs. If set to (-1),
2395 # the system will wait indefinitely until a key is pressed on the
2397 options PANIC_REBOOT_WAIT_TIME=16
2399 # Attempt to bypass the buffer cache and put data directly into the
2400 # userland buffer for read operation when O_DIRECT flag is set on the
2401 # file. Both offset and length of the read operation must be
2402 # multiples of the physical media sector size.
2406 # Specify a lower limit for the number of swap I/O buffers. They are
2407 # (among other things) used when bypassing the buffer cache due to
2408 # DIRECTIO kernel option enabled and O_DIRECT flag set on file.
2410 #options NSWBUF_MIN=120
2413 # SysVR4 ABI emulation
2415 # The svr4 ABI emulator can be statically compiled into the kernel or loaded as
2417 # The STREAMS network emulation code can also be compiled statically or as a
2418 # module. If loaded as a module, it must be loaded before the svr4 module
2419 # (the /usr/sbin/svr4 script does this for you). If compiling statically,
2420 # the `streams' pseudo-device must be configured into any kernel which also
2421 # specifies COMPAT_SVR4. It is possible to have a statically-configured
2422 # STREAMS device and a dynamically loadable svr4 emulator; the /usr/sbin/svr4
2423 # script understands that it doesn't need to load the `streams' module under
2424 # those circumstances.
2425 # Caveat: At this time, `options KTRACE' is required for the svr4 emulator
2426 # (whether static or dynamic).
2428 options COMPAT_SVR4 # build emulator statically
2429 options DEBUG_SVR4 # enable verbose debugging
2430 pseudo-device streams # STREAMS network driver (required for svr4).
2432 # The 'asr' driver provides support for current DPT/Adaptec SCSI RAID
2433 # controllers (SmartRAID V and VI and later).
2434 # These controllers require the CAM infrastructure.
2438 # The 'dpt' driver provides support for DPT controllers (http://www.dpt.com/).
2439 # These have hardware RAID-{0,1,5} support, and do multi-initiator I/O.
2440 # The DPT controllers are commonly re-licensed under other brand-names -
2441 # some controllers by Olivetti, Dec, HP, AT&T, SNI, AST, Alphatronic, NEC and
2442 # Compaq are actually DPT controllers.
2444 # See src/sys/dev/dpt for debugging and other subtle options.
2445 # DPT_MEASURE_PERFORMANCE Enables a set of (semi)invasive metrics. Various
2446 # instruments are enabled. The tools in
2447 # /usr/sbin/dpt_* assume these to be enabled.
2448 # DPT_HANDLE_TIMEOUTS Normally device timeouts are handled by the DPT.
2449 # If you ant the driver to handle timeouts, enable
2450 # this option. If your system is very busy, this
2451 # option will create more trouble than solve.
2452 # DPT_TIMEOUT_FACTOR Used to compute the excessive amount of time to
2453 # wait when timing out with the above option.
2454 # DPT_DEBUG_xxxx These are controllable from sys/dev/dpt/dpt.h
2455 # DPT_LOST_IRQ When enabled, will try, once per second, to catch
2456 # any interrupt that got lost. Seems to help in some
2457 # DPT-firmware/Motherboard combinations. Minimal
2458 # cost, great benefit.
2459 # DPT_RESET_HBA Make "reset" actually reset the controller
2460 # instead of fudging it. Only enable this if you
2461 # are 100% certain you need it.
2466 #!CAM# options DPT_MEASURE_PERFORMANCE
2467 #!CAM# options DPT_HANDLE_TIMEOUTS
2468 options DPT_TIMEOUT_FACTOR=4
2469 options DPT_LOST_IRQ
2470 options DPT_RESET_HBA
2471 options DPT_ALLOW_MEMIO
2474 # Compaq "CISS" RAID controllers (SmartRAID 5* series)
2475 # These controllers have a SCSI-like interface, and require the
2476 # CAM infrastructure.
2481 # Intel Integrated RAID controllers.
2482 # This driver was developed and is maintained by Intel. Contacts
2483 # at Intel for this driver are
2484 # "Kannanthanam, Boji T" <boji.t.kannanthanam@intel.com> and
2485 # "Leubner, Achim" <achim.leubner@intel.com>.
2490 # Mylex AcceleRAID and eXtremeRAID controllers with v6 and later
2491 # firmware. These controllers have a SCSI-like interface, and require
2492 # the CAM infrastructure.
2503 # General USB code (mandatory for USB)
2508 # Generic USB device driver
2510 # Human Interface Device (anything with buttons and dials)
2516 # USB Iomega Zip 100 Drive (Requires scbus and da)
2522 # USB Rio (MP3 Player)
2534 # ADMtek USB ethernet. Supports the LinkSys USB100TX,
2535 # the Billionton USB100, the Melco LU-ATX, the D-Link DSB-650TX
2536 # and the SMC 2202USB. Also works with the ADMtek AN986 Pegasus
2540 # ASIX Electronics AX88172 USB 2.0 ethernet driver. Used in the
2541 # LinkSys USB200M and various other adapters.
2544 # CATC USB-EL1201A USB ethernet. Supports the CATC Netmate
2545 # and Netmate II, and the Belkin F5U111.
2548 # Kawasaki LSI ethernet. Supports the LinkSys USB10T,
2549 # Entrega USB-NET-E45, Peracom Ethernet Adapter, the
2550 # 3Com 3c19250, the ADS Technologies USB-10BT, the ATen UC10T,
2551 # the Netgear EA101, the D-Link DSB-650, the SMC 2102USB
2552 # and 2104USB, and the Corega USB-T.
2555 # RealTek 8150 based USB ethernet device:
2557 # GREEN HOUSE GH-USB100B
2558 # Billionton ThumbLAN USBKR2-100B
2561 # debugging options for the USB subsystem
2566 options UKBD_DFLT_KEYMAP # specify the built-in keymap
2567 makeoptions UKBD_DFLT_KEYMAP=it.iso
2570 device firewire # Firewire bus code
2571 device sbp # SCSI over Firewire (Requires scbus and da)
2572 device fwe # Ethernet over Firewire (non-standard!)
2574 # dcons support (Dumb Console Device)
2575 device dcons # dumb console driver
2576 device dcons_crom # FireWire attachment
2577 options DCONS_BUF_SIZE=16384 # buffer size
2578 options DCONS_POLL_HZ=100 # polling rate
2579 options DCONS_FORCE_CONSOLE=1 # force to be the primary console
2580 options DCONS_FORCE_GDB=1 # force to be the gdb device
2582 #####################################################################
2585 # This is a port of the openbsd crypto framework. Include this when
2586 # configuring IPsec and when you have a h/w crypto device to accelerate
2587 # user applications that link to openssl.
2589 # Drivers are ports from openbsd with some simple enhancements that have
2590 # been fed back to openbsd (and hopefully will be included).
2592 pseudo-device crypto # core crypto support
2593 pseudo-device cryptodev # /dev/crypto for access to h/w
2595 device rndtest # FIPS 140-2 entropy tester
2597 device hifn # Hifn 7951, 7781, etc.
2598 options HIFN_DEBUG # enable debugging support: hw.hifn.debug
2599 options HIFN_RNDTEST # enable rndtest support
2601 device ubsec # Broadcom 5501, 5601, 58xx
2602 options UBSEC_DEBUG # enable debugging support: hw.ubsec.debug
2603 options UBSEC_RNDTEST # enable rndtest support
2605 device acpi # basic ACPI support
2608 # mgadrm: AGP Matrox G200, G400, G450, G550
2609 # tdfxdrm: 3dfx Voodoo 3/4/5 and Banshee
2610 # r128drm: ATI Rage 128
2611 # radeondrm: ATI Radeon up to 9000/9100
2612 # DRM_DEBUG: include debug printfs, very slow
2614 # mga requires AGP in the kernel, and it is recommended
2615 # for AGP r128 and radeon cards.
2625 # Embedded system options:
2627 # An embedded system might want to run something other than init.
2628 options INIT_PATH="/sbin/init:/stand/sysinstall"
2631 options BUS_DEBUG # enable newbus debugging
2632 options DEBUG_VFS_LOCKS # enable vfs lock debugging
2633 options NPX_DEBUG # enable npx debugging (FPU/math emu)
2635 # More undocumented options for linting.
2636 # Note that documenting these are not considered an affront.
2638 options AHC_DUMP_EEPROM
2639 options AHC_TMODE_ENABLE
2640 options CAM_DEBUG_DELAY
2641 options CLUSTERDEBUG
2642 options COMPAT_LINUX
2643 options CPU_UPGRADE_HW_CACHE
2646 #options DISABLE_PSE
2647 options ENABLE_ALART
2649 options FB_INSTALL_CDEV
2650 options FE_8BIT_SUPPORT
2651 options I4B_SMP_WORKAROUND
2652 options I586_PMC_GUPROF=0x70000
2654 options KBDIO_DEBUG=2
2655 options KBD_MAXRETRY=4
2656 options KBD_MAXWAIT=6
2657 options KBD_RESETDELAY=201
2661 options NETATALKDEBUG
2662 #options OLTR_NO_BULLSEYE_MAC
2663 #options OLTR_NO_HAWKEYE_MAC
2664 #options OLTR_NO_TMS_MAC
2666 options SCSI_NCR_DEBUG
2667 options SCSI_NCR_MAX_SYNC=10000
2668 options SCSI_NCR_MAX_WIDE=1
2669 options SCSI_NCR_MYADDR=7
2670 options SC_DEBUG_LEVEL
2671 options SC_RENDER_DEBUG
2672 options SHOW_BUSYBUFS # List buffers that prevent root unmount
2673 options SIMPLELOCK_DEBUG
2675 options SLIP_IFF_OPTS
2677 options TIMER_FREQ="((14318182+6)/12)"
2678 options VFS_BIO_DEBUG
2683 options KTR_ENTRIES=1024
2684 options KTR_VERBOSE=1
2687 options ALTQ #alternate queueing
2688 options ALTQ_CBQ #class based queueing
2689 options ALTQ_RED #random early detection
2690 options ALTQ_RIO #triple red for diffserv (needs RED)
2691 options ALTQ_HFSC #hierarchical fair service curve
2692 options ALTQ_PRIQ #priority queue
2693 #options ALTQ_NOPCC #don't use processor cycle counter
2694 options ALTQ_DEBUG #for debugging
2695 # you might want to set kernel timer to 1kHz if you use CBQ,
2696 # especially with 100baseT
projects / dragonfly.git / blob