sys/dev/disk/buslogic/btreg.h

   1 /*
   2  * Generic register and struct definitions for the BusLogic
   3  * MultiMaster SCSI host adapters.  Product specific probe and
   4  * attach routines can be found in:
   5  * sys/dev/buslogic/bt_isa.c    BT-54X, BT-445 cards
   6  * sys/dev/buslogic/bt_eisa.c   BT-74X, BT-75x cards, SDC3222F
   7  * sys/dev/buslogic/bt_pci.c    BT-946, BT-948, BT-956, BT-958 cards
   8  *
   9  * Copyright (c) 1998, 1999 Justin T. Gibbs.
  10  * All rights reserved.
  11  *
  12  * Redistribution and use in source and binary forms, with or without
  13  * modification, are permitted provided that the following conditions
  14  * are met:
  15  * 1. Redistributions of source code must retain the above copyright
  16  *    notice, this list of conditions, and the following disclaimer,
  17  *    without modification, immediately at the beginning of the file.
  18  * 2. The name of the author may not be used to endorse or promote products
  19  *    derived from this software without specific prior written permission.
  20  *
  21  * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND
  22  * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
  23  * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
  24  * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR
  25  * ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
  26  * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
  27  * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
  28  * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
  29  * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
  30  * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
  31  * SUCH DAMAGE.
  32  *
  33  * $FreeBSD: src/sys/dev/buslogic/btreg.h,v 1.10.2.2 2001/09/03 02:45:22 peter Exp $
  34  * $DragonFly: src/sys/dev/disk/buslogic/btreg.h,v 1.3 2005/06/11 09:03:48 swildner Exp $
  35  */
  36
  37 #ifndef _BTREG_H_
  38 #define _BTREG_H_
  39
  40 #include <sys/queue.h>
  41
  42 #define BT_MAXTRANSFER_SIZE      0xffffffff     /* limited by 32bit counter */
  43 #define BT_NSEG         32      /* The number of dma segments supported.
  44                                  * BT_NSEG can be maxed out at 8192 entries,
  45                                  * but the kernel will never need to transfer
  46                                  * such a large request.  To reduce the
  47                                  * driver's memory consumption, we reduce the
  48                                  * max to 32.  16 would work if all transfers
  49                                  * are paged alined since the kernel will only
  50                                  * generate at most a 64k transfer, but to
  51                                  * handle non-page aligned transfers, you need
  52                                  * 17, so we round to the next power of two
  53                                  * to make allocating SG space easy and
  54                                  * efficient.
  55                                  */
  56
  57 #define ALL_TARGETS (~0)
  58
  59 /*
  60  * Control Register pp. 1-8, 1-9 (Write Only)
  61  */
  62 #define CONTROL_REG             0x00
  63 #define         HARD_RESET      0x80    /* Hard Reset - return to POST state */
  64 #define         SOFT_RESET      0x40    /* Soft Reset - Clears Adapter state */
  65 #define         RESET_INTR      0x20    /* Reset/Ack Interrupt */
  66 #define         RESET_SBUS      0x10    /* Drive SCSI bus reset signal */
  67
  68 /*
  69  * Status Register pp. 1-9, 1-10 (Read Only)
  70  */
  71 #define STATUS_REG                      0x00
  72 #define         DIAG_ACTIVE             0x80    /* Performing Internal Diags */
  73 #define         DIAG_FAIL               0x40    /* Internal Diags failed */
  74 #define         INIT_REQUIRED           0x20    /* MBOXes need initialization */
  75 #define         HA_READY                0x10    /* HA ready for new commands */
  76 #define         CMD_REG_BUSY            0x08    /* HA busy with last cmd byte */
  77 #define         DATAIN_REG_READY        0x04    /* Data-in Byte available */
  78 #define         STATUS_REG_RSVD         0x02
  79 #define         CMD_INVALID             0x01    /* Invalid Command detected */
  80
  81 /*
  82  * Command/Parameter Register pp. 1-10, 1-11 (Write Only)
  83  */
  84 #define COMMAND_REG                     0x01
  85
  86 /*
  87  * Data in Register p. 1-11 (Read Only)
  88  */
  89 #define DATAIN_REG                      0x01
  90
  91 /*
  92  * Interrupt Status Register pp. 1-12 -> 1-14 (Read Only)
  93  */
  94 #define INTSTAT_REG                     0x02
  95 #define         INTR_PENDING            0x80    /* There is a pending INTR */
  96 #define         INTSTAT_REG_RSVD        0x70
  97 #define         SCSI_BUS_RESET          0x08    /* Bus Reset detected */
  98 #define         CMD_COMPLETE            0x04
  99 #define         OMB_READY               0x02    /* Outgoin Mailbox Ready */
 100 #define         IMB_LOADED              0x01    /* Incoming Mailbox loaded */
 101
 102 /*
 103  * Definitions for the "undocumented" geometry register
 104  */
 105 typedef enum {
 106         GEOM_NODISK,
 107         GEOM_64x32,
 108         GEOM_128x32,
 109         GEOM_255x32
 110 } disk_geom_t;
 111
 112 #define GEOMETRY_REG                    0x03
 113 #define         DISK0_GEOMETRY          0x03
 114 #define         DISK1_GEOMETRY          0x0c
 115 #define         EXTENDED_TRANSLATION    0x80
 116 #define         GEOMETRY_DISK0(g_reg) (greg & DISK0_GEOMETRY)
 117 #define         GEOMETRY_DISK1(g_reg) ((greg & DISK1_GEOMETRY) >> 2)
 118
 119 #define BT_NREGS        (4)
 120 /*
 121  * Opcodes for Adapter commands.
 122  * pp 1-18 -> 1-20
 123  */
 124 typedef enum {
 125         BOP_TEST_CMDC_INTR      = 0x00,
 126         BOP_INITIALIZE_24BMBOX  = 0x01,
 127         BOP_START_MBOX          = 0x02,
 128         BOP_EXECUTE_BIOS_CMD    = 0x03,
 129         BOP_INQUIRE_BOARD_ID    = 0x04,
 130         BOP_ENABLE_OMBR_INT     = 0x05,
 131         BOP_SET_SEL_TIMOUT      = 0x06,
 132         BOP_SET_TIME_ON_BUS     = 0x07,
 133         BOP_SET_TIME_OFF_BUS    = 0x08,
 134         BOP_SET_BUS_TRANS_RATE  = 0x09,
 135         BOP_INQUIRE_INST_LDEVS  = 0x0A,
 136         BOP_INQUIRE_CONFIG      = 0x0B,
 137         BOP_ENABLE_TARGET_MODE  = 0x0C,
 138         BOP_INQUIRE_SETUP_INFO  = 0x0D,
 139         BOP_WRITE_LRAM          = 0x1A,
 140         BOP_READ_LRAM           = 0x1B,
 141         BOP_WRITE_CHIP_FIFO     = 0x1C,
 142         BOP_READ_CHIP_FIFO      = 0x1C,
 143         BOP_ECHO_DATA_BYTE      = 0x1F,
 144         BOP_ADAPTER_DIAGNOSTICS = 0x20,
 145         BOP_SET_ADAPTER_OPTIONS = 0x21,
 146         BOP_INQUIRE_INST_HDEVS  = 0x23,
 147         BOP_INQUIRE_TARG_DEVS   = 0x24,
 148         BOP_DISABLE_HAC_INTR    = 0x25,
 149         BOP_INITIALIZE_32BMBOX  = 0x81,
 150         BOP_EXECUTE_SCSI_CMD    = 0x83,
 151         BOP_INQUIRE_FW_VER_3DIG = 0x84,
 152         BOP_INQUIRE_FW_VER_4DIG = 0x85,
 153         BOP_INQUIRE_PCI_INFO    = 0x86,
 154         BOP_INQUIRE_MODEL       = 0x8B,
 155         BOP_TARG_SYNC_INFO      = 0x8C,
 156         BOP_INQUIRE_ESETUP_INFO = 0x8D,
 157         BOP_ENABLE_STRICT_RR    = 0x8F,
 158         BOP_STORE_LRAM          = 0x90,
 159         BOP_FETCH_LRAM          = 0x91,
 160         BOP_SAVE_TO_EEPROM      = 0x92,
 161         BOP_UPLOAD_AUTO_SCSI    = 0x94,
 162         BOP_MODIFY_IO_ADDR      = 0x95,
 163         BOP_SET_CCB_FORMAT      = 0x96,
 164         BOP_FLASH_ROM_DOWNLOAD  = 0x97,
 165         BOP_FLASH_WRITE_ENABLE  = 0x98,
 166         BOP_WRITE_INQ_BUFFER    = 0x9A,
 167         BOP_READ_INQ_BUFFER     = 0x9B,
 168         BOP_FLASH_UP_DOWNLOAD   = 0xA7,
 169         BOP_READ_SCAM_DATA      = 0xA8,
 170         BOP_WRITE_SCAM_DATA     = 0xA9
 171 } bt_op_t;
 172
 173 /************** Definitions of Multi-byte commands and responses ************/
 174
 175 typedef struct {
 176         u_int8_t num_mboxes;
 177         u_int8_t base_addr[3];
 178 } init_24b_mbox_params_t;
 179
 180 typedef struct {
 181         u_int8_t board_type;
 182 #define         BOARD_TYPE_NON_MCA      0x41
 183 #define         BOARD_TYPE_MCA          0x42
 184         u_int8_t cust_features;
 185 #define         FEATURES_STANDARD       0x41
 186         u_int8_t firmware_rev_major;
 187         u_int8_t firmware_rev_minor;
 188 } board_id_data_t;
 189
 190 typedef struct {
 191         u_int8_t enable;
 192 } enable_ombr_intr_params_t;
 193
 194 typedef struct {
 195         u_int8_t enable;
 196         u_int8_t reserved;
 197         u_int8_t timeout[2];    /* timeout in milliseconds */
 198 } set_selto_parmas_t;
 199
 200 typedef struct {
 201         u_int8_t time;          /* time in milliseconds (2-15) */
 202 } set_timeon_bus_params_t;
 203
 204 typedef struct {
 205         u_int8_t time;          /* time in milliseconds (2-15) */
 206 } set_timeoff_bus_params_t;
 207
 208 typedef struct {
 209         u_int8_t rate;
 210 } set_bus_trasfer_rate_params_t;
 211
 212 typedef struct {
 213         u_int8_t targets[8];
 214 } installed_ldevs_data_t;
 215
 216 typedef struct {
 217         u_int8_t dma_chan;
 218 #define         DMA_CHAN_5      0x20
 219 #define         DMA_CHAN_6      0x40
 220 #define         DMA_CHAN_7      0x80
 221         u_int8_t irq;
 222 #define         IRQ_9           0x01
 223 #define         IRQ_10          0x02
 224 #define         IRQ_11          0x04
 225 #define         IRQ_12          0x08
 226 #define         IRQ_14          0x20
 227 #define         IRQ_15          0x40
 228         u_int8_t scsi_id;
 229 } config_data_t;
 230
 231 typedef struct {
 232         u_int8_t enable;
 233 } target_mode_params_t;
 234
 235 typedef struct {
 236         u_int8_t offset : 4,
 237                  period : 3,
 238                  sync   : 1;
 239 } targ_syncinfo_t;
 240
 241 typedef enum {
 242         HAB_ISA         = 'A',
 243         HAB_MCA         = 'B',
 244         HAB_EISA        = 'C',
 245         HAB_NUBUS       = 'D',
 246         HAB_VESA        = 'E',
 247         HAB_PCI         = 'F'
 248 } ha_type_t;
 249
 250 typedef struct {
 251         u_int8_t        initiate_sync   : 1,
 252                         parity_enable   : 1,
 253                                         : 6;
 254
 255         u_int8_t        bus_transfer_rate;
 256         u_int8_t        time_on_bus;
 257         u_int8_t        time_off_bus;
 258         u_int8_t        num_mboxes;
 259         u_int8_t        mbox_base_addr[3];
 260         targ_syncinfo_t low_syncinfo[8];        /* For fast and ultra, use 8C */
 261         u_int8_t        low_discinfo;
 262         u_int8_t        customer_sig;
 263         u_int8_t        letter_d;
 264         u_int8_t        ha_type;
 265         u_int8_t        low_wide_allowed;
 266         u_int8_t        low_wide_active;
 267         targ_syncinfo_t high_syncinfo[8];
 268         u_int8_t        high_discinfo;
 269         u_int8_t        high_wide_allowed;
 270         u_int8_t        high_wide_active;
 271 } setup_data_t;
 272
 273 typedef struct {
 274         u_int8_t phys_addr[3];
 275 } write_adapter_lram_params_t;
 276
 277 typedef struct {
 278         u_int8_t phys_addr[3];
 279 } read_adapter_lram_params_t;
 280
 281 typedef struct {
 282         u_int8_t phys_addr[3];
 283 } write_chip_fifo_params_t;
 284
 285 typedef struct {
 286         u_int8_t phys_addr[3];
 287 } read_chip_fifo_params_t;
 288
 289 typedef struct {
 290         u_int8_t length;                /* Excludes this member */
 291         u_int8_t low_disc_disable;
 292         u_int8_t low_busy_retry_disable;
 293         u_int8_t high_disc_disable;
 294         u_int8_t high_busy_retry_disable;
 295 } set_adapter_options_params_t;
 296
 297 typedef struct {
 298         u_int8_t targets[8];
 299 } installed_hdevs_data_t;
 300
 301 typedef struct {
 302         u_int8_t low_devs;
 303         u_int8_t high_devs;
 304 } target_devs_data_t;
 305
 306 typedef struct {
 307         u_int8_t enable;
 308 } enable_hac_interrupt_params_t;
 309
 310 typedef struct {
 311         u_int8_t num_boxes;
 312         u_int8_t base_addr[4];
 313 } init_32b_mbox_params_t;
 314
 315 typedef u_int8_t fw_ver_3dig_data_t;
 316
 317 typedef u_int8_t fw_ver_4dig_data_t;
 318
 319 typedef struct  {
 320         u_int8_t offset;
 321         u_int8_t response_len;
 322 } fetch_lram_params_t;
 323
 324 #define AUTO_SCSI_BYTE_OFFSET   64
 325 typedef struct {
 326         u_int8_t        factory_sig[2];
 327         u_int8_t        auto_scsi_data_size;    /* 2 -> 64 bytes */
 328         u_int8_t        model_num[6];
 329         u_int8_t        adapter_ioport;
 330         u_int8_t        floppy_enabled   :1,
 331                         floppy_secondary :1,
 332                         level_trigger    :1,
 333                                          :2,
 334                         system_ram_area  :3;
 335         u_int8_t        dma_channel      :7,
 336                         dma_autoconf     :1;
 337         u_int8_t        irq_channel      :7,
 338                         irq_autoconf     :1;
 339         u_int8_t        dma_trans_rate;
 340         u_int8_t        scsi_id;
 341         u_int8_t        low_termination  :1,
 342                         scsi_parity      :1,
 343                         high_termination :1,
 344                         req_ack_filter   :1,
 345                         fast_sync        :1,
 346                         bus_reset        :1,
 347                                          :1,
 348                         active_negation  :1;
 349         u_int8_t        bus_on_delay;
 350         u_int8_t        bus_off_delay;
 351         u_int8_t        bios_enabled     :1,
 352                         int19h_redirect  :1,
 353                         extended_trans   :1,
 354                         removable_drives :1,
 355                                          :1,
 356                         morethan2disks   :1,
 357                         interrupt_mode   :1,
 358                         floptical_support:1;
 359         u_int8_t        low_device_enabled;
 360         u_int8_t        high_device_enabled;
 361         u_int8_t        low_wide_permitted;
 362         u_int8_t        high_wide_permitted;
 363         u_int8_t        low_fast_permitted;
 364         u_int8_t        high_fast_permitted;
 365         u_int8_t        low_sync_permitted;
 366         u_int8_t        high_sync_permitted;
 367         u_int8_t        low_disc_permitted;
 368         u_int8_t        high_disc_permitted;
 369         u_int8_t        low_send_start_unit;
 370         u_int8_t        high_send_start_unit;
 371         u_int8_t        low_ignore_in_bios_scan;
 372         u_int8_t        high_ignore_in_bios_scan;
 373         u_int8_t        pci_int_pin      :2,
 374                         host_ioport      :2,
 375                         round_robin      :1,
 376                         vesa_bus_over_33 :1,
 377                         vesa_burst_write :1,
 378                         vesa_burst_read  :1;
 379         u_int8_t        low_ultra_permitted;
 380         u_int8_t        high_ultra_permitted;
 381         u_int8_t        reserved[5];
 382         u_int8_t        auto_scsi_max_lun;
 383         u_int8_t                         :1,
 384                         scam_dominant    :1,
 385                         scam_enabled     :1,
 386                         scam_level2      :1,
 387                                          :4;
 388         u_int8_t        int13_extensions :1,
 389                                          :1,
 390                         cdrom_boot       :1,
 391                                          :2,
 392                         multi_boot       :1,
 393                                          :2;
 394         u_int8_t        boot_target_id   :4,
 395                         boot_channel     :4;
 396         u_int8_t        force_dev_scan   :1,
 397                                          :7;
 398         u_int8_t        low_tagged_lun_independance;
 399         u_int8_t        high_tagged_lun_independance;
 400         u_int8_t        low_renegotiate_after_cc;
 401         u_int8_t        high_renegotiate_after_cc;
 402         u_int8_t        reserverd2[10];
 403         u_int8_t        manufacturing_diagnotic[2];
 404         u_int8_t        checksum[2];
 405 } auto_scsi_data_t;
 406
 407 struct bt_isa_port {
 408         u_int16_t addr;
 409         u_int8_t  probed;
 410         u_int8_t  bio;
 411 };
 412
 413 extern struct bt_isa_port bt_isa_ports[];
 414
 415 #define BT_NUM_ISAPORTS 6
 416
 417 typedef enum {
 418         BIO_330         = 0,
 419         BIO_334         = 1,
 420         BIO_230         = 2,
 421         BIO_234         = 3,
 422         BIO_130         = 4,
 423         BIO_134         = 5,
 424         BIO_DISABLED    = 6,
 425         BIO_DISABLED2   = 7
 426 } isa_compat_io_t;
 427
 428 typedef struct {
 429         u_int8_t io_port;
 430         u_int8_t irq_num;
 431         u_int8_t low_byte_term  :1,
 432                  high_byte_term :1,
 433                                 :2,
 434                  jp1_status     :1,
 435                  jp2_status     :1,
 436                  jp3_status     :1,
 437                                 :1;
 438         u_int8_t reserved;
 439 } pci_info_data_t;
 440
 441 typedef struct {
 442         u_int8_t ascii_model[5];        /* Fifth byte is always 0 */
 443 } ha_model_data_t;
 444
 445 typedef struct {
 446         u_int8_t sync_rate[16];         /* Sync in 10ns units */
 447 } target_sync_info_data_t;
 448
 449 typedef struct {
 450         u_int8_t  bus_type;
 451         u_int8_t  bios_addr;
 452         u_int16_t max_sg;
 453         u_int8_t  num_mboxes;
 454         u_int8_t  mbox_base[4];
 455         u_int8_t                        :2,
 456                   sync_neg10MB          :1,
 457                   floppy_disable        :1,
 458                   floppy_secondary_port :1,
 459                   burst_mode_enabled    :1,
 460                   level_trigger_ints    :1,
 461                                         :1;
 462         u_int8_t  fw_ver_bytes_2_to_4[3];
 463         u_int8_t  wide_bus              :1,
 464                   diff_bus              :1,
 465                   scam_capable          :1,
 466                   ultra_scsi            :1,
 467                   auto_term             :1,
 468                                         :3;
 469 } esetup_info_data_t;
 470
 471 typedef struct {
 472         u_int32_t len;
 473         u_int32_t addr;
 474 } bt_sg_t;
 475
 476 /********************** Mail Box definitions *******************************/
 477
 478 typedef enum {
 479         BMBO_FREE               = 0x0,  /* MBO intry is free */
 480         BMBO_START              = 0x1,  /* MBO activate entry */
 481         BMBO_ABORT              = 0x2   /* MBO abort entry */
 482 } bt_mbo_action_code_t;
 483
 484 typedef struct bt_mbox_out {
 485         u_int32_t ccb_addr;
 486         u_int8_t  reserved[3];
 487         u_int8_t  action_code;
 488 } bt_mbox_out_t;
 489
 490 typedef enum {
 491         BMBI_FREE               = 0x0,  /* MBI entry is free */
 492         BMBI_OK                 = 0x1,  /* completed without error */
 493         BMBI_ABORT              = 0x2,  /* aborted ccb */
 494         BMBI_NOT_FOUND          = 0x3,  /* Tried to abort invalid CCB */
 495         BMBI_ERROR              = 0x4   /* Completed with error */
 496 } bt_mbi_comp_code_t;
 497
 498 typedef struct bt_mbox_in {
 499         u_int32_t ccb_addr;
 500         u_int8_t  btstat;
 501         u_int8_t  sdstat;
 502         u_int8_t  reserved;
 503         u_int8_t  comp_code;
 504 } bt_mbox_in_t;
 505
 506 /***************** Compiled Probe Information *******************************/
 507 struct bt_probe_info {
 508         int     drq;
 509         int     irq;
 510 };
 511
 512 /****************** Hardware CCB definition *********************************/
 513 typedef enum {
 514         INITIATOR_CCB           = 0x00,
 515         INITIATOR_SG_CCB        = 0x02,
 516         INITIATOR_CCB_WRESID    = 0x03,
 517         INITIATOR_SG_CCB_WRESID = 0x04,
 518         INITIATOR_BUS_DEV_RESET = 0x81
 519 } bt_ccb_opcode_t;
 520
 521 typedef enum {
 522         BTSTAT_NOERROR                  = 0x00,
 523         BTSTAT_LINKED_CMD_COMPLETE      = 0x0A,
 524         BTSTAT_LINKED_CMD_FLAG_COMPLETE = 0x0B,
 525         BTSTAT_DATAUNDERUN_ERROR        = 0x0C,
 526         BTSTAT_SELTIMEOUT               = 0x11,
 527         BTSTAT_DATARUN_ERROR            = 0x12,
 528         BTSTAT_UNEXPECTED_BUSFREE       = 0x13,
 529         BTSTAT_INVALID_PHASE            = 0x14,
 530         BTSTAT_INVALID_ACTION_CODE      = 0x15,
 531         BTSTAT_INVALID_OPCODE           = 0x16,
 532         BTSTAT_LINKED_CCB_LUN_MISMATCH  = 0x17,
 533         BTSTAT_INVALID_CCB_OR_SG_PARAM  = 0x1A,
 534         BTSTAT_AUTOSENSE_FAILED         = 0x1B,
 535         BTSTAT_TAGGED_MSG_REJECTED      = 0x1C,
 536         BTSTAT_UNSUPPORTED_MSG_RECEIVED = 0x1D,
 537         BTSTAT_HARDWARE_FAILURE         = 0x20,
 538         BTSTAT_TARGET_IGNORED_ATN       = 0x21,
 539         BTSTAT_HA_SCSI_BUS_RESET        = 0x22,
 540         BTSTAT_OTHER_SCSI_BUS_RESET     = 0x23,
 541         BTSTAT_INVALID_RECONNECT        = 0x24,
 542         BTSTAT_HA_BDR                   = 0x25,
 543         BTSTAT_ABORT_QUEUE_GENERATED    = 0x26,
 544         BTSTAT_HA_SOFTWARE_ERROR        = 0x27,
 545         BTSTAT_HA_WATCHDOG_ERROR        = 0x28,
 546         BTSTAT_SCSI_PERROR_DETECTED     = 0x30
 547 } btstat_t;
 548
 549 struct bt_hccb {
 550         u_int8_t  opcode;
 551         u_int8_t                        :3,
 552                   datain                :1,
 553                   dataout               :1,
 554                   wide_tag_enable       :1,     /* Wide Lun CCB format */
 555                   wide_tag_type         :2;     /* Wide Lun CCB format */
 556         u_int8_t  cmd_len;
 557         u_int8_t  sense_len;
 558         int32_t   data_len;                     /* residuals can be negative */
 559         u_int32_t data_addr;
 560         u_int8_t  reserved[2];
 561         u_int8_t  btstat;
 562         u_int8_t  sdstat;
 563         u_int8_t  target_id;
 564         u_int8_t  target_lun    :5,
 565                   tag_enable    :1,
 566                   tag_type      :2;
 567         u_int8_t  scsi_cdb[12];
 568         u_int8_t  reserved2[6];
 569         u_int32_t sense_addr;
 570 };
 571
 572 typedef enum {
 573         BCCB_FREE               = 0x0,
 574         BCCB_ACTIVE             = 0x1,
 575         BCCB_DEVICE_RESET       = 0x2,
 576         BCCB_RELEASE_SIMQ       = 0x4
 577 } bccb_flags_t;
 578
 579 struct bt_ccb {
 580         struct  bt_hccb          hccb;
 581         SLIST_ENTRY(bt_ccb)      links;
 582         u_int32_t                flags;
 583         union ccb               *ccb;
 584         bus_dmamap_t             dmamap;
 585         bt_sg_t                 *sg_list;
 586         u_int32_t                sg_list_phys;
 587 };
 588
 589 struct sg_map_node {
 590         bus_dmamap_t             sg_dmamap;
 591         bus_addr_t               sg_physaddr;
 592         bt_sg_t*                 sg_vaddr;
 593         SLIST_ENTRY(sg_map_node) links;
 594 };
 595
 596 struct bt_softc {
 597         struct device           *dev;
 598         struct resource         *port;
 599         struct resource         *irq;
 600         struct resource         *drq;
 601         void                    *ih;
 602         bus_space_tag_t          tag;
 603         bus_space_handle_t       bsh;
 604         struct  cam_sim         *sim;
 605         struct  cam_path        *path;
 606         bt_mbox_out_t           *cur_outbox;
 607         bt_mbox_in_t            *cur_inbox;
 608         bt_mbox_out_t           *last_outbox;
 609         bt_mbox_in_t            *last_inbox;
 610         struct  bt_ccb          *bt_ccb_array;
 611         SLIST_HEAD(,bt_ccb)      free_bt_ccbs;
 612         LIST_HEAD(,ccb_hdr)      pending_ccbs;
 613         u_int                    active_ccbs;
 614         u_int32_t                bt_ccb_physbase;
 615         bt_mbox_in_t            *in_boxes;
 616         bt_mbox_out_t           *out_boxes;
 617         struct scsi_sense_data  *sense_buffers;
 618         u_int32_t                sense_buffers_physbase;
 619         struct  bt_ccb          *recovery_bccb;
 620         u_int                    num_boxes;
 621         bus_dma_tag_t            parent_dmat;   /*
 622                                                  * All dmat's derive from
 623                                                  * the dmat defined by our
 624                                                  * bus.
 625                                                  */
 626         bus_dma_tag_t            buffer_dmat;   /* dmat for buffer I/O */
 627         bus_dma_tag_t            mailbox_dmat;  /* dmat for our mailboxes */
 628         bus_dmamap_t             mailbox_dmamap;
 629         bus_dma_tag_t            ccb_dmat;      /* dmat for our ccb array */
 630         bus_dmamap_t             ccb_dmamap;
 631         bus_dma_tag_t            sg_dmat;       /* dmat for our sg segments */
 632         bus_dma_tag_t            sense_dmat;    /* dmat for our sense buffers */
 633         bus_dmamap_t             sense_dmamap;
 634         SLIST_HEAD(, sg_map_node) sg_maps;
 635         bus_addr_t               mailbox_physbase;
 636         u_int                    num_ccbs;      /* Number of CCBs malloc'd */
 637         u_int                    max_ccbs;      /* Maximum allocatable CCBs */
 638         u_int                    max_sg;
 639         u_int                    unit;
 640         u_int                    scsi_id;
 641         u_int32_t                extended_trans    :1,
 642                                  wide_bus          :1,
 643                                  diff_bus          :1,
 644                                  ultra_scsi        :1,
 645                                  extended_lun      :1,
 646                                  strict_rr         :1,
 647                                  tag_capable       :1,
 648                                  wide_lun_ccb      :1,
 649                                  resource_shortage :1,
 650                                  level_trigger_ints:1,
 651                                                    :22;
 652         u_int16_t                tags_permitted;
 653         u_int16_t                disc_permitted;
 654         u_int16_t                sync_permitted;
 655         u_int16_t                fast_permitted;
 656         u_int16_t                ultra_permitted;
 657         u_int16_t                wide_permitted;
 658         u_int8_t                 init_level;
 659         volatile u_int8_t        command_cmp;
 660         volatile u_int8_t        latched_status;
 661         u_int32_t                bios_addr;
 662         char                     firmware_ver[6];
 663         char                     model[5];
 664 };
 665
 666 extern u_long bt_unit;
 667
 668 #define BT_TEMP_UNIT 0xFF               /* Unit for probes */
 669 void                    bt_init_softc(device_t dev,
 670                                       struct resource *port,
 671                                       struct resource *irq,
 672                                       struct resource *drq);
 673 void                    bt_free_softc(device_t dev);
 674 int                     bt_port_probe(device_t dev,
 675                                       struct bt_probe_info *info);
 676 int                     bt_probe(device_t dev);
 677 int                     bt_fetch_adapter_info(device_t dev);
 678 int                     bt_init(device_t dev);
 679 int                     bt_attach(device_t dev);
 680 void                    bt_intr(void *arg);
 681 int                     bt_check_probed_iop(u_int ioport);
 682 void                    bt_mark_probed_bio(isa_compat_io_t port);
 683 void                    bt_mark_probed_iop(u_int ioport);
 684 void                    bt_find_probe_range(int ioport,
 685                                             int *port_index,
 686                                             int *max_port_index);
 687
 688 int                     bt_iop_from_bio(isa_compat_io_t bio_index);
 689
 690 #define DEFAULT_CMD_TIMEOUT 100000      /* 10 sec */
 691 int                     bt_cmd(struct bt_softc *bt, bt_op_t opcode,
 692                                u_int8_t *params, u_int param_len,
 693                                u_int8_t *reply_data, u_int reply_len,
 694                                u_int cmd_timeout);
 695
 696 #define bt_name(bt)     device_get_nameunit(bt->dev)
 697
 698 #define bt_inb(bt, port)                                \
 699         bus_space_read_1((bt)->tag, (bt)->bsh, port)
 700
 701 #define bt_outb(bt, port, value)                        \
 702         bus_space_write_1((bt)->tag, (bt)->bsh, port, value)
 703
 704 #endif  /* _BT_H_ */