2 # LINT -- config file for checking all the sources, tries to pull in
3 # as much of the source tree as it can.
5 # $FreeBSD: src/sys/i386/conf/LINT,v 1.749.2.144 2003/06/04 17:56:59 sam Exp $
6 # $DragonFly: src/sys/config/LINT,v 1.26 2004/04/16 19:49:09 drhodus Exp $
8 # NB: You probably don't want to try running a kernel built from this
9 # file. Instead, you should start from GENERIC, and add options from
10 # this file as required.
14 # This directive is mandatory; it defines the architecture to be
15 # configured for; in this case, the 386 family based IBM-PC and
21 # This is the ``identification'' of the kernel. Usually this should
22 # be the same as the name of your kernel.
27 # The `maxusers' parameter controls the static sizing of a number of
28 # internal system tables by a formula defined in subr_param.c. Setting
29 # maxusers to 0 will cause the system to auto-size based on physical
35 # The `makeoptions' parameter allows variables to be passed to the
36 # generated Makefile in the build area.
38 # CONF_CFLAGS gives some extra compiler flags that are added to ${CFLAGS}
39 # after most other flags. Here we use it to inhibit use of non-optimal
40 # gcc builtin functions (e.g., memcmp).
42 # DEBUG happens to be magic.
43 # The following is equivalent to 'config -g KERNELNAME' and creates
44 # 'kernel.debug' compiled with -g debugging as well as a normal
45 # 'kernel'. Use 'make install.debug' to install the debug kernel
46 # but that isn't normally necessary as the debug symbols are not loaded
47 # by the kernel and are not useful there anyway.
49 # KERNEL can be overridden so that you can change the default name of your
52 # MODULES_OVERRIDE can be used to limit modules built to a specific list.
54 makeoptions CONF_CFLAGS=-fno-builtin #Don't allow use of memcmp, etc.
55 #makeoptions DEBUG=-g #Build kernel with gdb(1) debug symbols
56 #makeoptions KERNEL=foo #Build kernel "foo" and install "/foo"
57 # Only build Linux API modules and plus those parts of the sound system I need.
58 #makeoptions MODULES_OVERRIDE="linux sound/snd sound/pcm sound/driver/maestro3"
61 # Certain applications can grow to be larger than the 128M limit
62 # that FreeBSD initially imposes. Below are some options to
63 # allow that limit to grow to 256MB, and can be increased further
64 # with changing the parameters. MAXDSIZ is the maximum that the
65 # limit can be set to, and the DFLDSIZ is the default value for
66 # the limit. MAXSSIZ is the maximum that the stack limit can be
67 # set to. You might want to set the default lower than the max,
68 # and explicitly set the maximum with a shell command for processes
69 # that regularly exceed the limit like INND.
71 options MAXDSIZ="(256*1024*1024)"
72 options MAXSSIZ="(256*1024*1024)"
73 options DFLDSIZ="(256*1024*1024)"
76 # BLKDEV_IOSIZE sets the default block size used in user block
77 # device I/O. Note that this value will be overriden by the label
78 # when specifying a block device from a label with a non-0
79 # partition blocksize. The default is PAGE_SIZE.
81 options BLKDEV_IOSIZE=8192
83 # Options for the VM subsystem.
84 options PQ_CACHESIZE=512 # color for 512k/16k cache
85 # Deprecated options supported for backwards compatibility.
86 #options PQ_NOOPT # No coloring
87 #options PQ_LARGECACHE # color for 512k/16k cache
88 #options PQ_HUGECACHE # color for 1024k/16k cache
89 #options PQ_MEDIUMCACHE # color for 256k/16k cache
90 #options PQ_NORMALCACHE # color for 64k/16k cache
92 # This allows you to actually store this configuration file into
93 # the kernel binary itself, where it may be later read by saying:
94 # strings -n 3 /kernel | sed -n 's/^___//p' > MYKERNEL
96 options INCLUDE_CONFIG_FILE # Include this file in kernel
99 # The root device and filesystem type can be compiled in;
100 # this provides a fallback option if the root device cannot
101 # be correctly guessed by the bootstrap code, or an override if
102 # the RB_DFLTROOT flag (-r) is specified when booting the kernel.
104 options ROOTDEVNAME=\"ufs:da0s2e\"
107 #####################################################################
110 # SMP enables building of a Symmetric MultiProcessor Kernel.
111 # APIC_IO enables the use of the IO APIC for Symmetric I/O.
115 # An SMP kernel will ONLY run on an Intel MP spec. qualified motherboard.
117 # Be sure to disable 'cpu I386_CPU' && 'cpu I486_CPU' for SMP kernels.
119 # Check the 'Rogue SMP hardware' section to see if additional options
120 # are required by your hardware.
124 options SMP # Symmetric MultiProcessor Kernel
125 options APIC_IO # Symmetric (APIC) I/O
128 # Rogue SMP hardware:
133 # The MP tables of most of the current generation MP motherboards
134 # do NOT properly support bridged PCI cards. To use one of these
135 # cards you should refer to ???
138 #####################################################################
142 # You must specify at least one CPU (the one you intend to run on);
143 # deleting the specification for CPUs you don't need to use may make
144 # parts of the system run faster. This is especially true removing
149 cpu I586_CPU # aka Pentium(tm)
150 cpu I686_CPU # aka Pentium Pro(tm)
153 # Options for CPU features.
155 # CPU_ATHLON_SSE_HACK tries to enable SSE instructions when the BIOS has
156 # forgotten to enable them.
158 # CPU_BLUELIGHTNING_FPU_OP_CACHE enables FPU operand cache on IBM
159 # BlueLightning CPU. It works only with Cyrix FPU, and this option
160 # should not be used with Intel FPU.
162 # CPU_BLUELIGHTNING_3X enables triple-clock mode on IBM Blue Lightning
163 # CPU if CPU supports it. The default is double-clock mode on
164 # BlueLightning CPU box.
166 # CPU_BTB_EN enables branch target buffer on Cyrix 5x86 (NOTE 1).
168 # CPU_DIRECT_MAPPED_CACHE sets L1 cache of Cyrix 486DLC CPU in direct
169 # mapped mode. Default is 2-way set associative mode.
171 # CPU_CYRIX_NO_LOCK enables weak locking for the entire address space
172 # of Cyrix 6x86 and 6x86MX CPUs by setting the NO_LOCK bit of CCR1.
173 # Otherwise, the NO_LOCK bit of CCR1 is cleared. (NOTE 3)
175 # CPU_DISABLE_5X86_LSSER disables load store serialize (i.e. enables
176 # reorder). This option should not be used if you use memory mapped
179 # CPU_DISABLE_SSE disables SSE/MMX2 instructions support.
181 # CPU_FASTER_5X86_FPU enables faster FPU exception handler.
183 # CPU_I486_ON_386 enables CPU cache on i486 based CPU upgrade products
186 # CPU_IORT defines I/O clock delay time (NOTE 1). Default values of
187 # I/O clock delay time on Cyrix 5x86 and 6x86 are 0 and 7,respectively
190 # CPU_L2_LATENCY specifed the L2 cache latency value. This option is used
191 # only when CPU_PPRO2CELERON is defined and Mendocino Celeron is detected.
192 # The default value is 5.
194 # CPU_ELAN enables support for AMDs ElanSC520 CPU.
196 # CPU_LOOP_EN prevents flushing the prefetch buffer if the destination
197 # of a jump is already present in the prefetch buffer on Cyrix 5x86(NOTE
200 # CPU_PPRO2CELERON enables L2 cache of Mendocino Celeron CPUs. This option
201 # is useful when you use Socket 8 to Socket 370 converter, because most Pentium
202 # Pro BIOSs do not enable L2 cache of Mendocino Celeron CPUs.
204 # CPU_RSTK_EN enables return stack on Cyrix 5x86 (NOTE 1).
206 # CPU_SUSP_HLT enables suspend on HALT. If this option is set, CPU
207 # enters suspend mode following execution of HALT instruction.
209 # CPU_WT_ALLOC enables write allocation on Cyrix 6x86/6x86MX and AMD
212 # CYRIX_CACHE_WORKS enables CPU cache on Cyrix 486 CPUs with cache
213 # flush at hold state.
215 # CYRIX_CACHE_REALLY_WORKS enables (1) CPU cache on Cyrix 486 CPUs
216 # without cache flush at hold state, and (2) write-back CPU cache on
217 # Cyrix 6x86 whose revision < 2.7 (NOTE 2).
219 # NO_F00F_HACK disables the hack that prevents Pentiums (and ONLY
220 # Pentiums) from locking up when a LOCK CMPXCHG8B instruction is
221 # executed. This option is only needed if I586_CPU is also defined,
222 # and should be included for any non-Pentium CPU that defines it.
224 # NO_MEMORY_HOLE is an optimisation for systems with AMD K6 processors
225 # which indicates that the 15-16MB range is *definitely* not being
226 # occupied by an ISA memory hole.
228 # NOTE 1: The options, CPU_BTB_EN, CPU_LOOP_EN, CPU_IORT,
229 # CPU_LOOP_EN and CPU_RSTK_EN should not be used because of CPU bugs.
230 # These options may crash your system.
232 # NOTE 2: If CYRIX_CACHE_REALLY_WORKS is not set, CPU cache is enabled
233 # in write-through mode when revision < 2.7. If revision of Cyrix
234 # 6x86 >= 2.7, CPU cache is always enabled in write-back mode.
236 # NOTE 3: This option may cause failures for software that requires
237 # locked cycles in order to operate correctly.
239 options CPU_ATHLON_SSE_HACK
240 options CPU_BLUELIGHTNING_FPU_OP_CACHE
241 options CPU_BLUELIGHTNING_3X
243 options CPU_DIRECT_MAPPED_CACHE
244 options CPU_DISABLE_5X86_LSSER
246 options CPU_DISABLE_SSE
247 options CPU_FASTER_5X86_FPU
248 options CPU_I486_ON_386
250 options CPU_L2_LATENCY=5
252 options CPU_PPRO2CELERON
256 options CYRIX_CACHE_WORKS
257 options CYRIX_CACHE_REALLY_WORKS
258 #options NO_F00F_HACK
261 # A math emulator is mandatory if you wish to run on hardware which
262 # does not have a floating-point processor. Pick either the original,
263 # bogus (but freely-distributable) math emulator, or a much more
264 # fully-featured but GPL-licensed emulator taken from Linux.
266 options MATH_EMULATE #Support for x87 emulation
267 # Don't enable both of these in a real config.
268 options GPL_MATH_EMULATE #Support for x87 emulation via
272 #####################################################################
273 # COMPATIBILITY OPTIONS
276 # Implement system calls compatible with 4.3BSD and older versions of
277 # FreeBSD. You probably do NOT want to remove this as much current code
278 # still relies on the 4.3 emulation.
283 # These three options provide support for System V Interface
284 # Definition-style interprocess communication, in the form of shared
285 # memory, semaphores, and message queues, respectively.
287 # System V shared memory and tunable parameters
288 options SYSVSHM # include support for shared memory
289 options SHMMAXPGS=1025 # max amount of shared memory pages (4k on i386)
290 options SHMALL=1025 # max amount of shared memory (bytes)
291 options SHMMAX="(SHMMAXPGS*PAGE_SIZE+1)"
292 # max shared memory segment size (bytes)
293 options SHMMIN=2 # min shared memory segment size (bytes)
294 options SHMMNI=33 # max number of shared memory identifiers
295 options SHMSEG=9 # max shared memory segments per process
297 # System V semaphores and tunable parameters
298 options SYSVSEM # include support for semaphores
299 options SEMMAP=31 # amount of entries in semaphore map
300 options SEMMNI=11 # number of semaphore identifiers in the system
301 options SEMMNS=61 # number of semaphores in the system
302 options SEMMNU=31 # number of undo structures in the system
303 options SEMMSL=61 # max number of semaphores per id
304 options SEMOPM=101 # max number of operations per semop call
305 options SEMUME=11 # max number of undo entries per process
307 # System V message queues and tunable parameters
308 options SYSVMSG # include support for message queues
309 options MSGMNB=2049 # max characters per message queue
310 options MSGMNI=41 # max number of message queue identifiers
311 options MSGSEG=2049 # max number of message segments in the system
312 options MSGSSZ=16 # size of a message segment MUST be power of 2
313 options MSGTQL=41 # max amount of messages in the system
316 #####################################################################
320 # Enable the kernel debugger.
325 # Don't drop into DDB for a panic. Intended for unattended operation
326 # where you may want to drop to DDB from the console, but still want
327 # the machine to recover from a panic
329 options DDB_UNATTENDED
332 # If using GDB remote mode to debug the kernel, there's a non-standard
333 # extension to the remote protocol that can be used to use the serial
334 # port as both the debugging port and the system console. It's non-
335 # standard and you're on your own if you enable it. See also the
336 # "remotechat" variables in the FreeBSD specific version of gdb.
338 options GDB_REMOTE_CHAT
341 # KTRACE enables the system-call tracing facility ktrace(2).
343 options KTRACE #kernel tracing
346 # The INVARIANTS option is used in a number of source files to enable
347 # extra sanity checking of internal structures. This support is not
348 # enabled by default because of the extra time it would take to check
349 # for these conditions, which can only occur as a result of
350 # programming errors.
355 # The INVARIANT_SUPPORT option makes us compile in support for
356 # verifying some of the internal structures. It is a prerequisite for
357 # 'INVARIANTS', as enabling 'INVARIANTS' will make these functions be
358 # called. The intent is that you can set 'INVARIANTS' for single
359 # source files (by changing the source file or specifying it on the
360 # command line) if you have 'INVARIANT_SUPPORT' enabled.
362 options INVARIANT_SUPPORT
365 # The DIAGNOSTIC option is used to enable extra debugging information
366 # from some parts of the kernel. As this makes everything more noisy,
367 # it is disabled by default.
372 # PERFMON causes the driver for Pentium/Pentium Pro performance counters
373 # to be compiled. See perfmon(4) for more information.
379 # This option let some drivers co-exist that can't co-exist in a running
380 # system. This is used to be able to compile all kernel code in one go for
381 # quality assurance purposes (like this file, which the option takes it name
384 options COMPILING_LINT
387 # XXX - this doesn't belong here.
388 # Allow ordinary users to take the console - this is useful for X.
391 # XXX - this doesn't belong here either
392 options USERCONFIG #boot -c editor
393 options INTRO_USERCONFIG #imply -c and show intro screen
394 options VISUAL_USERCONFIG #visual boot -c editor
397 #####################################################################
402 # Only the INET (Internet) family is officially supported in FreeBSD.
403 # Source code for the NS (Xerox Network Service) is provided for amusement
406 options INET #Internet communications protocols
407 options INET6 #IPv6 communications protocols
408 options IPSEC #IP security
409 options IPSEC_ESP #IP security (crypto; define w/ IPSEC)
410 options IPSEC_DEBUG #debug for IP security
412 # Set IPSEC_FILTERGIF to force packets coming through a gif tunnel
413 # to be processed by any configured packet filtering (ipfw, ipf).
414 # The default is that packets coming from a tunnel are _not_ processed;
415 # they are assumed trusted.
417 # Note that enabling this can be problematic as there are no mechanisms
418 # in place for distinguishing packets coming out of a tunnel (e.g. no
419 # encX devices as found on openbsd).
421 #options IPSEC_FILTERGIF #filter ipsec packets from a tunnel
424 # Experimental IPsec implementation that uses the kernel crypto
425 # framework. This cannot be configured together with IPSEC and
426 # (currently) supports only IPv4. To use this you must also
427 # configure the crypto device (see below). Note that with this
428 # you get all the IPsec protocols (e.g. there is no FAST_IPSEC_ESP).
429 # IPSEC_DEBUG is used, as above, to configure debugging support
430 # within the IPsec protocols.
432 #options FAST_IPSEC #new IPsec
434 options IPX #IPX/SPX communications protocols
435 options IPXIP #IPX in IP encapsulation (not available)
436 options IPTUNNEL #IP in IPX encapsulation (not available)
438 options NCP #NetWare Core protocol
440 options NETATALK #Appletalk communications protocols
442 # These are currently broken but are shipped due to interest.
443 #options NS #Xerox NS protocols
444 #options NSIP #XNS over IP
448 # NETSMB enables support for SMB protocol, it requires LIBMCHAIN and LIBICONV
450 # NETSMBCRYPTO enables support for encrypted passwords.
451 options NETSMB #SMB/CIFS requester
452 options NETSMBCRYPTO #encrypted password support for SMB
454 # mchain library. It can be either loaded as KLD or compiled into kernel
455 options LIBMCHAIN #mbuf management library
457 # netgraph(4). Enable the base netgraph code with the NETGRAPH option.
458 # Individual node types can be enabled with the corresponding option
459 # listed below; however, this is not strictly necessary as netgraph
460 # will automatically load the corresponding KLD module if the node type
461 # is not already compiled into the kernel. Each type below has a
462 # corresponding man page, e.g., ng_async(8).
463 options NETGRAPH #netgraph(4) system
464 options NETGRAPH_ASYNC
466 options NETGRAPH_CISCO
467 options NETGRAPH_ECHO
468 options NETGRAPH_ETHER
469 options NETGRAPH_FRAME_RELAY
470 options NETGRAPH_HOLE
471 options NETGRAPH_IFACE
472 options NETGRAPH_KSOCKET
473 options NETGRAPH_L2TP
475 # MPPC compression requires proprietary files (not included)
476 #options NETGRAPH_MPPC_COMPRESSION
477 options NETGRAPH_MPPC_ENCRYPTION
478 options NETGRAPH_ONE2MANY
480 options NETGRAPH_PPPOE
481 options NETGRAPH_PPTPGRE
482 options NETGRAPH_RFC1490
483 options NETGRAPH_SOCKET
489 device mn # Munich32x/Falc54 Nx64kbit/sec cards.
492 # Network interfaces:
493 # The `loop' pseudo-device is MANDATORY when networking is enabled.
494 # The `ether' pseudo-device provides generic code to handle
495 # Ethernets; it is MANDATORY when a Ethernet device driver is
496 # configured or token-ring is enabled.
497 # The 'fddi' pseudo-device provides generic code to support FDDI.
498 # The `arcnet' pseudo-device provides generic code to support Arcnet.
499 # The `sppp' pseudo-device serves a similar role for certain types
500 # of synchronous PPP links (like `cx', `ar').
501 # The `sl' pseudo-device implements the Serial Line IP (SLIP) service.
502 # The `ppp' pseudo-device implements the Point-to-Point Protocol.
503 # The `bpf' pseudo-device enables the Berkeley Packet Filter. Be
504 # aware of the legal and administrative consequences of enabling this
505 # option. The number of devices determines the maximum number of
506 # simultaneous BPF clients programs runnable.
507 # The `disc' pseudo-device implements a minimal network interface,
508 # which throws away all packets sent and never receives any. It is
509 # included for testing purposes. This shows up as the 'ds' interface.
510 # The `tun' pseudo-device implements (user-)ppp and nos-tun
511 # The `gif' pseudo-device implements IPv6 over IP4 tunneling,
512 # IPv4 over IPv6 tunneling, IPv4 over IPv4 tunneling and
513 # IPv6 over IPv6 tunneling.
514 # The `gre' device implements two types of IP4 over IP4 tunneling:
515 # GRE and MOBILE, as specified in the RFC1701 and RFC2004.
516 # The `faith' pseudo-device captures packets sent to it and diverts them
517 # to the IPv4/IPv6 translation daemon.
518 # The `stf' device implements 6to4 encapsulation.
519 # The `ef' pseudo-device provides support for multiple ethernet frame types
520 # specified via ETHER_* options. See ef(4) for details.
522 # The PPP_BSDCOMP option enables support for compress(1) style entire
523 # packet compression, the PPP_DEFLATE is for zlib/gzip style compression.
524 # PPP_FILTER enables code for filtering the ppp data stream and selecting
525 # events for resetting the demand dial activity timer - requires bpf.
526 # See pppd(8) for more details.
528 pseudo-device ether #Generic Ethernet
529 pseudo-device vlan 1 #VLAN support
530 pseudo-device token #Generic TokenRing
531 pseudo-device fddi #Generic FDDI
532 pseudo-device arcnet #Generic Arcnet
533 pseudo-device sppp #Generic Synchronous PPP
534 pseudo-device loop #Network loopback device
535 pseudo-device bpf #Berkeley packet filter
536 options PFIL_HOOKS #Packetfilter hooks
537 pseudo-device disc #Discard device (ds0, ds1, etc)
538 pseudo-device tun #Tunnel driver (ppp(8), nos-tun(8))
539 pseudo-device sl 2 #Serial Line IP
540 pseudo-device gre #IP over IP tunneling
541 pseudo-device ppp 2 #Point-to-point protocol
542 options PPP_BSDCOMP #PPP BSD-compress support
543 options PPP_DEFLATE #PPP zlib/deflate/gzip support
544 options PPP_FILTER #enable bpf filtering (needs bpf)
546 pseudo-device ef # Multiple ethernet frames support
547 options ETHER_II # enable Ethernet_II frame
548 options ETHER_8023 # enable Ethernet_802.3 (Novell) frame
549 options ETHER_8022 # enable Ethernet_802.2 frame
550 options ETHER_SNAP # enable Ethernet_802.2/SNAP frame
553 pseudo-device gif #IPv6 and IPv4 tunneling
554 pseudo-device faith 1 #for IPv6 and IPv4 translation
555 pseudo-device stf #6to4 IPv6 over IPv4 encapsulation
558 # Internet family options:
560 # MROUTING enables the kernel multicast packet forwarder, which works
563 # PIM enables Protocol Independent Multicast in the kernel.
564 # Requires MROUTING enabled.
566 # IPFIREWALL enables support for IP firewall construction, in
567 # conjunction with the `ipfw' program. IPFIREWALL_VERBOSE sends
568 # logged packets to the system logger. IPFIREWALL_VERBOSE_LIMIT
569 # limits the number of times a matching entry can be logged.
571 # WARNING: IPFIREWALL defaults to a policy of "deny ip from any to any"
572 # and if you do not add other rules during startup to allow access,
573 # YOU WILL LOCK YOURSELF OUT. It is suggested that you set firewall_type=open
574 # in /etc/rc.conf when first enabling this feature, then refining the
575 # firewall rules in /etc/rc.firewall after you've tested that the new kernel
576 # feature works properly.
578 # IPFIREWALL_DEFAULT_TO_ACCEPT causes the default rule (at boot) to
579 # allow everything. Use with care, if a cracker can crash your
580 # firewall machine, they can get to your protected machines. However,
581 # if you are using it as an as-needed filter for specific problems as
582 # they arise, then this may be for you. Changing the default to 'allow'
583 # means that you won't get stuck if the kernel and /sbin/ipfw binary get
586 # IPDIVERT enables the divert IP sockets, used by ``ipfw divert''
588 # IPSTEALTH enables code to support stealth forwarding (i.e., forwarding
589 # packets without touching the ttl). This can be useful to hide firewalls
590 # from traceroute and similar tools.
592 # TCPDEBUG is undocumented.
594 options MROUTING # Multicast routing
595 options PIM # Protocol Independent Multicast
596 options IPFIREWALL #firewall
597 options IPFIREWALL_VERBOSE #enable logging to syslogd(8)
598 options IPFIREWALL_FORWARD #enable transparent proxy support
599 options IPFIREWALL_VERBOSE_LIMIT=100 #limit verbosity
600 options IPFIREWALL_DEFAULT_TO_ACCEPT #allow everything by default
601 options IPV6FIREWALL #firewall for IPv6
602 options IPV6FIREWALL_VERBOSE
603 options IPV6FIREWALL_VERBOSE_LIMIT=100
604 options IPV6FIREWALL_DEFAULT_TO_ACCEPT
605 options IPDIVERT #divert sockets
606 options IPFILTER #ipfilter support
607 options IPFILTER_LOG #ipfilter logging
608 options IPFILTER_DEFAULT_BLOCK #block all packets by default
609 options IPSTEALTH #support for stealth forwarding
611 options NS # NETNS support
613 # The MBUF_STRESS_TEST option enables options which create
614 # various random failures / extreme cases related to mbuf
615 # functions. See the mbuf(9) manpage for a list of available
617 options MBUF_STRESS_TEST
619 # RANDOM_IP_ID causes the ID field in IP packets to be randomized
620 # instead of incremented by 1 with each packet generated. This
621 # option closes a minor information leak which allows remote
622 # observers to determine the rate of packet generation on the
623 # machine by watching the counter.
626 # Statically link in accept filters
627 options ACCEPT_FILTER_DATA
628 options ACCEPT_FILTER_HTTP
631 # TCP_DROP_SYNFIN adds support for ignoring TCP packets with SYN+FIN. This
632 # prevents nmap et al. from identifying the TCP/IP stack, but breaks support
633 # for RFC1644 extensions and is not recommended for web servers.
635 options TCP_DROP_SYNFIN #drop TCP packets with SYN+FIN
637 # ICMP_BANDLIM enables icmp error response bandwidth limiting. You
638 # typically want this option as it will help protect the machine from
639 # D.O.S. packet attacks.
643 # DUMMYNET enables the "dummynet" bandwidth limiter. You need
644 # IPFIREWALL as well. See the dummynet(4) and ipfw(8) manpages for more info.
645 # When you run DUMMYNET it is advisable to also have "options HZ=1000"
646 # to achieve a smoother scheduling of the traffic.
648 # BRIDGE enables bridging between ethernet cards -- see bridge(4).
649 # You can use IPFIREWALL and DUMMYNET together with bridging.
655 # ATM (HARP version) options
657 # ATM_CORE includes the base ATM functionality code. This must be included
660 # ATM_IP includes support for running IP over ATM.
662 # At least one (and usually only one) of the following signalling managers
663 # must be included (note that all signalling managers include PVC support):
664 # ATM_SIGPVC includes support for the PVC-only signalling manager `sigpvc'.
665 # ATM_SPANS includes support for the `spans' signalling manager, which runs
666 # the FORE Systems's proprietary SPANS signalling protocol.
667 # ATM_UNI includes support for the `uni30' and `uni31' signalling managers,
668 # which run the ATM Forum UNI 3.x signalling protocols.
670 # The `hea' driver provides support for the Efficient Networks, Inc.
671 # ENI-155p ATM PCI Adapter.
673 # The `hfa' driver provides support for the FORE Systems, Inc.
674 # PCA-200E ATM PCI Adapter.
676 options ATM_CORE #core ATM protocol family
677 options ATM_IP #IP over ATM support
678 options ATM_SIGPVC #SIGPVC signalling manager
679 options ATM_SPANS #SPANS signalling manager
680 options ATM_UNI #UNI signalling manager
681 device hea #Efficient ENI-155p ATM PCI
682 device hfa #FORE PCA-200E ATM PCI
684 # DEVICE_POLLING adds support for mixed interrupt-polling handling
685 # of network device drivers, which has significant benefits in terms
686 # of robustness to overloads and responsivity, as well as permitting
687 # accurate scheduling of the CPU time between kernel network processing
688 # and other activities. The drawback is a moderate (up to 1/HZ seconds)
689 # potential increase in response times.
690 # It is strongly recommended to use HZ=1000 or 2000 with DEVICE_POLLING
691 # to achieve smoother behaviour.
692 # Additionally, you can enable/disable polling at runtime with the
693 # sysctl variable kern.polling.enable (defaults off), and select
694 # the CPU fraction reserved to userland with the sysctl variable
695 # kern.polling.user_frac (default 50, range 0..100).
697 # Only the "dc" "fxp" and "sis" devices support this mode of operation at
698 # the time of this writing.
700 options DEVICE_POLLING
703 #####################################################################
707 # Only the root, /usr, and /tmp filesystems need be statically
708 # compiled; everything else will be automatically loaded at mount
709 # time. (Exception: the UFS family---FFS, and MFS --- cannot
710 # currently be demand-loaded.) Some people still prefer to statically
711 # compile other filesystems as well.
713 # NB: The NULL, PORTAL, UMAP and UNION filesystems are known to be
714 # buggy, and WILL panic your system if you attempt to do anything with
715 # them. They are included here as an incentive for some enterprising
716 # soul to sit down and fix them.
719 # One of these is mandatory:
720 options FFS #Fast filesystem
721 options MFS #Memory File System
722 options NFS #Network File System
724 # The rest are optional:
725 #options NFS_NOSERVER #Disable the NFS-server code.
726 options CD9660 #ISO 9660 filesystem
727 options FDESC #File descriptor filesystem
728 options KERNFS #Kernel filesystem
729 options MSDOSFS #MS DOS File System
730 options NTFS #NT File System
731 options NULLFS #NULL filesystem
732 options NWFS #NetWare filesystem
733 options PORTAL #Portal filesystem
734 options PROCFS #Process filesystem
735 options SMBFS #SMB/CIFS filesystem
736 options UDF #UDF filesystem
737 options UMAPFS #UID map filesystem
738 options UNION #Union filesystem
739 # The xFS_ROOT options REQUIRE the associated ``options xFS''
740 options CD9660_ROOT #CD-ROM usable as root device
741 options FFS_ROOT #FFS usable as root device
742 options NFS_ROOT #NFS usable as root device
744 # Soft updates is technique for improving file system speed and
745 # making abrupt shutdown less risky.
748 # Directory hashing improves the speed of operations on very large
749 # directories at the expense of some memory.
752 # Make space in the kernel for a root filesystem on a md device.
753 # Define to the number of kilobytes to reserve for the filesystem.
754 options MD_ROOT_SIZE=10
756 # Make the md device a potential root device, either with preloaded
757 # images of type mfs_root or md_root.
760 # Specify double the default maximum size for malloc(9)-backed md devices.
761 options MD_NSECT=40000
763 # Allow this many swap-devices.
765 # In order to manage swap, the system must reserve bitmap space that
766 # scales with the largest mounted swap device multiplied by NSWAPDEV,
767 # irregardless of whether other swap devices exist or not. So it
768 # is not a good idea to make this value too large.
771 # Disk quotas are supported when this option is enabled.
772 options QUOTA #enable disk quotas
774 # If you are running a machine just as a fileserver for PC and MAC
775 # users, using SAMBA or Netatalk, you may consider setting this option
776 # and keeping all those users' directories on a filesystem that is
777 # mounted with the suiddir option. This gives new files the same
778 # ownership as the directory (similar to group). It's a security hole
779 # if you let these users run programs, so confine it to file-servers
780 # (but it'll save you lots of headaches in those cases). Root owned
781 # directories are exempt and X bits are cleared. The suid bit must be
782 # set on the directory as well; see chmod(1) PC owners can't see/set
783 # ownerships so they keep getting their toes trodden on. This saves
784 # you all the support calls as the filesystem it's used on will act as
785 # they expect: "It's my dir so it must be my file".
790 options NFS_MINATTRTIMO=3 # VREG attrib cache timeout in sec
791 options NFS_MAXATTRTIMO=60
792 options NFS_MINDIRATTRTIMO=30 # VDIR attrib cache timeout in sec
793 options NFS_MAXDIRATTRTIMO=60
794 options NFS_GATHERDELAY=10 # Default write gather delay (msec)
795 options NFS_UIDHASHSIZ=29 # Tune the size of nfssvc_sock with this
796 options NFS_WDELAYHASHSIZ=16 # and with this
797 options NFS_MUIDHASHSIZ=63 # Tune the size of nfsmount with this
798 options NFS_DEBUG # Enable NFS Debugging
801 options CODA #CODA filesystem.
802 pseudo-device vcoda 4 #coda minicache <-> venus comm.
805 # Add support for the EXT2FS filesystem of Linux fame. Be a bit
806 # careful with this - the ext2fs code has a tendency to lag behind
807 # changes and not be exercised very much, so mounting read/write could
808 # be dangerous (and even mounting read only could result in panics.)
812 # Use real implementations of the aio_* system calls. There are numerous
813 # stability and security issues in the current aio code that make it
814 # unsuitable for inclusion on machines with untrusted local users.
818 #####################################################################
821 # Real time extensions added in the 1993 Posix
822 # P1003_1B: Infrastructure
823 # _KPOSIX_PRIORITY_SCHEDULING: Build in _POSIX_PRIORITY_SCHEDULING
824 # _KPOSIX_VERSION: Version kernel is built for
827 options _KPOSIX_PRIORITY_SCHEDULING
828 options _KPOSIX_VERSION=199309L
831 #####################################################################
834 # The granularity of operation is controlled by the kernel option HZ whose
835 # default value (100) means a granularity of 10ms (1s/HZ).
836 # Some subsystems, such as DUMMYNET or DEVICE_POLLING, might benefit from
837 # a smaller granularity such as 1ms or less.
838 # Consider, however, that reducing the granularity too much might
839 # cause excessive overhead in clock interrupt processing,
840 # potentially causing ticks to be missed and thus actually reducing
841 # the accuracy of operation.
845 # The following options are used for debugging clock behavior only, and
846 # should not be used for production systems.
848 # CLK_CALIBRATION_LOOP will run the clock calibration loop at startup
849 # until the user presses a key.
851 options CLK_CALIBRATION_LOOP
853 # The following two options measure the frequency of the corresponding
854 # clock relative to the RTC (onboard mc146818a).
856 options CLK_USE_I8254_CALIBRATION
857 options CLK_USE_TSC_CALIBRATION
860 #####################################################################
863 # SCSI DEVICE CONFIGURATION
865 # The SCSI subsystem consists of the `base' SCSI code, a number of
866 # high-level SCSI device `type' drivers, and the low-level host-adapter
867 # device drivers. The host adapters are listed in the ISA and PCI
868 # device configuration sections below.
870 # Beginning with FreeBSD 2.0.5 you can wire down your SCSI devices so
871 # that a given bus, target, and LUN always come on line as the same
872 # device unit. In earlier versions the unit numbers were assigned
873 # in the order that the devices were probed on the SCSI bus. This
874 # means that if you removed a disk drive, you may have had to rewrite
875 # your /etc/fstab file, and also that you had to be careful when adding
876 # a new disk as it may have been probed earlier and moved your device
877 # configuration around.
879 # This old behavior is maintained as the default behavior. The unit
880 # assignment begins with the first non-wired down unit for a device
881 # type. For example, if you wire a disk as "da3" then the first
882 # non-wired disk will be assigned da4.
884 # The syntax for wiring down devices is:
886 # device scbus0 at ahc0 # Single bus device
887 # device scbus1 at ahc1 bus 0 # Single bus device
888 # device scbus3 at ahc2 bus 0 # Twin bus device
889 # device scbus2 at ahc2 bus 1 # Twin bus device
890 # device da0 at scbus0 target 0 unit 0
891 # device da1 at scbus3 target 1
892 # device da2 at scbus2 target 3
893 # device sa1 at scbus1 target 6
896 # "units" (SCSI logical unit number) that are not specified are
897 # treated as if specified as LUN 0.
899 # All SCSI devices allocate as many units as are required.
901 # The "unknown" device (uk? in pre-2.0.5) is now part of the base SCSI
902 # configuration and doesn't have to be explicitly configured.
904 device scbus #base SCSI code
905 device ch #SCSI media changers
906 device da #SCSI direct access devices (aka disks)
907 device sa #SCSI tapes
908 device cd #SCSI CD-ROMs
909 device pass #CAM passthrough driver
910 device pt #SCSI processor type
911 device ses #SCSI SES/SAF-TE driver
915 # -- NOTE -- If you specify one of the bus/target/lun options, you must
917 # CAMDEBUG: When defined enables debugging macros
918 # CAM_DEBUG_BUS: Debug the given bus. Use -1 to debug all busses.
919 # CAM_DEBUG_TARGET: Debug the given target. Use -1 to debug all targets.
920 # CAM_DEBUG_LUN: Debug the given lun. Use -1 to debug all luns.
921 # CAM_DEBUG_FLAGS: OR together CAM_DEBUG_INFO, CAM_DEBUG_TRACE,
922 # CAM_DEBUG_SUBTRACE, and CAM_DEBUG_CDB
924 # CAM_MAX_HIGHPOWER: Maximum number of concurrent high power (start unit) cmds
925 # SCSI_NO_SENSE_STRINGS: When defined disables sense descriptions
926 # SCSI_NO_OP_STRINGS: When defined disables opcode descriptions
927 # SCSI_DELAY: The number of MILLISECONDS to freeze the SIM (scsi adapter)
928 # queue after a bus reset, and the number of milliseconds to
929 # freeze the device queue after a bus device reset.
931 options CAM_DEBUG_BUS=-1
932 options CAM_DEBUG_TARGET=-1
933 options CAM_DEBUG_LUN=-1
934 options CAM_DEBUG_FLAGS="CAM_DEBUG_INFO|CAM_DEBUG_TRACE|CAM_DEBUG_CDB"
935 options CAM_MAX_HIGHPOWER=4
936 options SCSI_NO_SENSE_STRINGS
937 options SCSI_NO_OP_STRINGS
938 options SCSI_DELAY=8000 # Be pessimistic about Joe SCSI device
940 # Options for the CAM CDROM driver:
941 # CHANGER_MIN_BUSY_SECONDS: Guaranteed minimum time quantum for a changer LUN
942 # CHANGER_MAX_BUSY_SECONDS: Maximum time quantum per changer LUN, only
943 # enforced if there is I/O waiting for another LUN
944 # The compiled in defaults for these variables are 2 and 10 seconds,
947 # These can also be changed on the fly with the following sysctl variables:
948 # kern.cam.cd.changer.min_busy_seconds
949 # kern.cam.cd.changer.max_busy_seconds
951 options CHANGER_MIN_BUSY_SECONDS=2
952 options CHANGER_MAX_BUSY_SECONDS=10
954 # Options for the CAM sequential access driver:
955 # SA_IO_TIMEOUT: Timeout for read/write/wfm operations, in minutes
956 # SA_SPACE_TIMEOUT: Timeout for space operations, in minutes
957 # SA_REWIND_TIMEOUT: Timeout for rewind operations, in minutes
958 # SA_ERASE_TIMEOUT: Timeout for erase operations, in minutes
959 # SA_1FM_AT_EOD: Default to model which only has a default one filemark at EOT.
960 options SA_IO_TIMEOUT="(4)"
961 options SA_SPACE_TIMEOUT="(60)"
962 options SA_REWIND_TIMEOUT="(2*60)"
963 options SA_ERASE_TIMEOUT="(4*60)"
964 options SA_1FM_AT_EOD
966 # Optional timeout for the CAM processor target (pt) device
967 # This is specified in seconds. The default is 60 seconds.
968 options SCSI_PT_DEFAULT_TIMEOUT="60"
970 # Optional enable of doing SES passthrough on other devices (e.g., disks)
972 # Normally disabled because a lot of newer SCSI disks report themselves
973 # as having SES capabilities, but this can then clot up attempts to build
974 # build a topology with the SES device that's on the box these drives
976 options SES_ENABLE_PASSTHROUGH
979 #####################################################################
980 # MISCELLANEOUS DEVICES AND OPTIONS
982 # The `pty' device usually turns out to be ``effectively mandatory'',
983 # as it is required for `telnetd', `rlogind', `screen', `emacs', and
984 # `xterm', among others.
986 pseudo-device pty #Pseudo ttys
987 pseudo-device speaker #Play IBM BASIC-style noises out your speaker
988 pseudo-device gzip #Exec gzipped a.out's
989 pseudo-device vn #Vnode driver (turns a file into a device)
990 pseudo-device md #Memory/malloc disk
991 pseudo-device snp #Snoop device - to look at pty/vty/etc..
992 pseudo-device ccd 4 #Concatenated disk driver
994 # Configuring Vinum into the kernel is not necessary, since the kld
995 # module gets started automatically when vinum(8) starts. This
996 # device is also untested. Use at your own risk.
998 # The option VINUMDEBUG must match the value set in CFLAGS
999 # in src/sbin/vinum/Makefile. Failure to do so will result in
1000 # the following message from vinum(8):
1002 # Can't get vinum config: Invalid argument
1004 # see vinum(4) for more reasons not to use these options.
1005 pseudo-device vinum #Vinum concat/mirror/raid driver
1006 options VINUMDEBUG #enable Vinum debugging hooks
1008 # Kernel side iconv library
1011 # Size of the kernel message buffer. Should be N * pagesize.
1012 options MSGBUF_SIZE=40960
1015 #####################################################################
1016 # HARDWARE DEVICE CONFIGURATION
1018 # ISA and EISA devices:
1019 # EISA support is available for some device, so they can be auto-probed.
1020 # MicroChannel (MCA) support is available for some devices.
1023 # Mandatory ISA devices: isa, npx
1028 # Options for `isa':
1030 # AUTO_EOI_1 enables the `automatic EOI' feature for the master 8259A
1031 # interrupt controller. This saves about 0.7-1.25 usec for each interrupt.
1032 # This option breaks suspend/resume on some portables.
1034 # AUTO_EOI_2 enables the `automatic EOI' feature for the slave 8259A
1035 # interrupt controller. This saves about 0.7-1.25 usec for each interrupt.
1036 # Automatic EOI is documented not to work for for the slave with the
1037 # original i8259A, but it works for some clones and some integrated
1040 # MAXMEM specifies the amount of RAM on the machine; if this is not
1041 # specified, FreeBSD will first read the amount of memory from the CMOS
1042 # RAM, so the amount of memory will initially be limited to 64MB or 16MB
1043 # depending on the BIOS. If the BIOS reports 64MB, a memory probe will
1044 # then attempt to detect the installed amount of RAM. If this probe
1045 # fails to detect >64MB RAM you will have to use the MAXMEM option.
1046 # The amount is in kilobytes, so for a machine with 128MB of RAM, it would
1047 # be 131072 (128 * 1024).
1049 # BROKEN_KEYBOARD_RESET disables the use of the keyboard controller to
1050 # reset the CPU for reboot. This is needed on some systems with broken
1051 # keyboard controllers.
1053 # PAS_JOYSTICK_ENABLE enables the gameport on the ProAudio Spectrum
1055 options COMPAT_OLDISA #FreeBSD 2.2 and 3.x compatibility shims
1058 options MAXMEM="(128*1024)"
1059 #options BROKEN_KEYBOARD_RESET
1060 #options PAS_JOYSTICK_ENABLE
1062 # Enable support for the kernel PLL to use an external PPS signal,
1063 # under supervision of [x]ntpd(8)
1064 # More info in ntpd documentation: http://www.eecis.udel.edu/~ntp
1068 # If you see the "calcru: negative time of %ld usec for pid %d (%s)\n"
1069 # message you probably have some broken sw/hw which disables interrupts
1070 # for too long. You can make the system more resistant to this by
1071 # choosing a high value for NTIMECOUNTER. The default is 5, there
1072 # is no upper limit but more than a couple of hundred are not productive.
1073 # A better strategy may be to sysctl -w kern.timecounter.method=1
1075 options NTIMECOUNTER=20
1077 # The keyboard controller; it controls the keyboard and the PS/2 mouse.
1078 device atkbdc0 at isa? port IO_KBD
1081 device atkbd0 at atkbdc? irq 1
1083 # Options for atkbd:
1084 options ATKBD_DFLT_KEYMAP # specify the built-in keymap
1085 makeoptions ATKBD_DFLT_KEYMAP="jp.106"
1087 # These options are valid for other keyboard drivers as well.
1088 options KBD_DISABLE_KEYMAP_LOAD # refuse to load a keymap
1089 options KBD_INSTALL_CDEV # install a CDEV entry in /dev
1091 # `flags' for atkbd:
1092 # 0x01 Force detection of keyboard, else we always assume a keyboard
1093 # 0x02 Don't reset keyboard, useful for some newer ThinkPads
1094 # 0x03 Force detection and avoid reset, might help with certain
1096 # 0x04 Old-style (XT) keyboard support, useful for older ThinkPads
1099 device psm0 at atkbdc? irq 12
1102 options PSM_HOOKRESUME #hook the system resume event, useful
1104 options PSM_RESETAFTERSUSPEND #reset the device at the resume event
1106 # The video card driver.
1110 # Try the following option if the mouse pointer is not drawn correctly
1111 # or font does not seem to be loaded properly. May cause flicker on
1113 options VGA_ALT_SEQACCESS
1115 # If you can dispense with some vga driver features, you may want to
1116 # use the following options to save some memory.
1117 options VGA_NO_FONT_LOADING # don't save/load font
1118 options VGA_NO_MODE_CHANGE # don't change video modes
1120 # Older video cards may require this option for proper operation.
1121 options VGA_SLOW_IOACCESS # do byte-wide i/o's to TS and GDC regs
1123 # The following option probably won't work with the LCD displays.
1124 options VGA_WIDTH90 # support 90 column modes
1126 # To include support for VESA video modes
1129 # Splash screen at start up! Screen savers require this too.
1130 pseudo-device splash
1132 # The pcvt console driver (vt220 compatible).
1134 options XSERVER # support for running an X server on vt
1135 options FAT_CURSOR # start with block cursor
1136 # This PCVT option is for keyboards such as those used on IBM ThinkPad laptops
1137 options PCVT_SCANSET=2 # IBM keyboards are non-std
1138 # Other PCVT options are documented in pcvt(4).
1139 options PCVT_24LINESDEF
1140 options PCVT_CTRL_ALT_DEL
1141 options PCVT_EMU_MOUSE
1142 options PCVT_FREEBSD=211
1143 options PCVT_META_ESC
1144 options PCVT_NSCREENS=9
1145 options PCVT_PRETTYSCRNS
1146 options PCVT_SCREENSAVER
1147 options PCVT_USEKBDSEC
1148 options PCVT_VT220KEYB
1150 # The syscons console driver (sco color console compatible).
1152 options MAXCONS=16 # number of virtual consoles
1153 options SC_ALT_MOUSE_IMAGE # simplified mouse cursor in text mode
1154 options SC_DFLT_FONT # compile font in
1155 makeoptions SC_DFLT_FONT=cp850
1156 options SC_DISABLE_DDBKEY # disable `debug' key
1157 options SC_DISABLE_REBOOT # disable reboot key sequence
1158 options SC_HISTORY_SIZE=200 # number of history buffer lines
1159 options SC_MOUSE_CHAR=0x3 # char code for text mode mouse cursor
1160 options SC_PIXEL_MODE # add support for the raster text mode
1162 # The following options will let you change the default colors of syscons.
1163 options SC_NORM_ATTR="(FG_GREEN|BG_BLACK)"
1164 options SC_NORM_REV_ATTR="(FG_YELLOW|BG_GREEN)"
1165 options SC_KERNEL_CONS_ATTR="(FG_RED|BG_BLACK)"
1166 options SC_KERNEL_CONS_REV_ATTR="(FG_BLACK|BG_RED)"
1168 # If you have a two button mouse, you may want to add the following option
1169 # to use the right button of the mouse to paste text.
1170 options SC_TWOBUTTON_MOUSE
1172 # You can selectively disable features in syscons.
1173 options SC_NO_CUTPASTE
1174 options SC_NO_FONT_LOADING
1175 options SC_NO_HISTORY
1176 options SC_NO_SYSMOUSE
1179 # The Numeric Processing eXtension driver. In addition to this, you
1180 # may configure a math emulator (see above). If your machine has a
1181 # hardware FPU and the kernel configuration includes the npx device
1182 # *and* a math emulator compiled into the kernel, the hardware FPU
1183 # will be used, unless it is found to be broken or unless "flags" to
1184 # npx0 includes "0x08", which requests preference for the emulator.
1185 device npx0 at nexus? port IO_NPX flags 0x0 irq 13
1189 # 0x01 don't use the npx registers to optimize bcopy.
1190 # 0x02 don't use the npx registers to optimize bzero.
1191 # 0x04 don't use the npx registers to optimize copyin or copyout.
1192 # 0x08 use emulator even if hardware FPU is available.
1193 # The npx registers are normally used to optimize copying and zeroing when
1194 # all of the following conditions are satisfied:
1195 # I586_CPU is an option
1196 # the cpu is an i586 (perhaps not a Pentium)
1197 # the probe for npx0 succeeds
1198 # INT 16 exception handling works.
1199 # Then copying and zeroing using the npx registers is normally 30-100% faster.
1200 # The flags can be used to control cases where it doesn't work or is slower.
1201 # Setting them at boot time using userconfig works right (the optimizations
1202 # are not used until later in the bootstrap when npx0 is attached).
1203 # Flag 0x08 automatically disables the i586 optimized routines.
1207 # Optional ISA and EISA devices:
1211 # SCSI host adapters: `aha', `aic', `bt'
1213 # adv: All Narrow SCSI bus AdvanSys controllers.
1214 # adw: Second Generation AdvanSys controllers including the ADV940UW.
1216 # ahc: Adaptec 274x/284x/294x
1218 # bt: Most Buslogic controllers
1219 # ncv: NCR 53C500 based SCSI host adapters.
1220 # nsp: Workbit Ninja SCSI-3 based PC Card SCSI host adapters.
1221 # stg: TMC 18C30, 18C50 based ISA/PC Card SCSI host adapters.
1223 # Note that the order is important in order for Buslogic cards to be
1227 device bt0 at isa? port IO_BT0
1234 device stg0 at isa? port 0x140 irq 11
1237 # Adaptec FSA RAID controllers, including integrated DELL controller,
1238 # the Dell PERC 2/QC and the HP NetRAID-4M
1241 device aacp # SCSI Passthrough interface (optional, CAM required)
1244 # Compaq Smart RAID, Mylex DAC960 and AMI MegaRAID controllers. Only
1245 # one entry is needed; the code will find and configure all supported
1248 device ida # Compaq Smart RAID
1249 device mlx # Mylex DAC960
1250 device amr # AMI MegaRAID
1255 device twe # 3ware ATA RAID
1258 # Promise Supertrack SX6000
1268 # The 'ATA' driver supports all ATA and ATAPI devices.
1269 # It can reuse the majors of wd.c for booting purposes.
1270 # You only need one "device ata" for it to find all
1271 # PCI ATA/ATAPI devices on modern machines.
1273 device atadisk # ATA disk drives
1274 device atapicd # ATAPI CDROM drives
1275 device atapifd # ATAPI floppy drives
1276 device atapist # ATAPI tape drives
1277 device atapicam # emulate ATAPI devices as SCSI ditto via CAM
1278 # needs CAM to be present (scbus & pass)
1280 #The following options are valid on the ATA driver:
1282 # ATA_STATIC_ID: controller numbering is static (like the old driver)
1283 # else the device numbers are dynamically allocated.
1284 options ATA_STATIC_ID
1287 # For older non-PCI systems, these are the lines to use:
1288 #device ata0 at isa? port IO_WD1 irq 14
1289 #device ata1 at isa? port IO_WD2 irq 15
1292 # Standard floppy disk controllers: `fdc' and `fd'
1294 device fdc0 at isa? port IO_FD1 irq 6 drq 2
1296 # FDC_DEBUG enables floppy debugging. Since the debug output is huge, you
1297 # gotta turn it actually on by setting the variable fd_debug with DDB,
1301 device fd0 at fdc0 drive 0
1302 device fd1 at fdc0 drive 1
1304 # M-systems DiskOnchip products see src/sys/contrib/dev/fla/README
1308 # Other standard PC hardware: `mse', `sio', etc.
1310 # mse: Logitech and ATI InPort bus mouse ports
1311 # sio: serial ports (see sio(4))
1313 device mse0 at isa? port 0x23c irq 5
1315 device sio0 at isa? port IO_COM1 flags 0x10 irq 4
1318 # `flags' for serial drivers that support consoles (only for sio now):
1319 # 0x10 enable console support for this unit. The other console flags
1320 # are ignored unless this is set. Enabling console support does
1321 # not make the unit the preferred console - boot with -h or set
1322 # the 0x20 flag for that. Currently, at most one unit can have
1323 # console support; the first one (in config file order) with
1324 # this flag set is preferred. Setting this flag for sio0 gives
1325 # the old behaviour.
1326 # 0x20 force this unit to be the console (unless there is another
1327 # higher priority console). This replaces the COMCONSOLE option.
1328 # 0x40 reserve this unit for low level console operations. Do not
1329 # access the device in any normal way.
1330 # 0x80 use this port for serial line gdb support in ddb.
1332 # PnP `flags' (set via userconfig using pnp x flags y)
1333 # 0x1 disable probing of this device. Used to prevent your modem
1334 # from being attached as a PnP modem.
1337 # Options for serial drivers that support consoles (only for sio now):
1338 options BREAK_TO_DEBUGGER #a BREAK on a comconsole goes to
1340 options CONSPEED=115200 # speed for serial console
1343 # Solaris implements a new BREAK which is initiated by a character
1344 # sequence CR ~ ^b which is similar to a familiar pattern used on
1345 # Sun servers by the Remote Console.
1346 options ALT_BREAK_TO_DEBUGGER
1349 options COM_ESP #code for Hayes ESP
1350 options COM_MULTIPORT #code for some cards with shared IRQs
1352 # Other flags for sio that aren't documented in the man page.
1353 # 0x20000 enable hardware RTS/CTS and larger FIFOs. Only works for
1354 # ST16650A-compatible UARTs.
1356 # PCI Universal Communications driver
1357 # Supports various single and multi port PCI serial cards. Maybe later
1358 # also the parallel ports on combination serial/parallel cards. New cards
1359 # can be added in src/sys/dev/puc/pucdata.c.
1361 # If the PUC_FASTINTR option is used the driver will try to use fast
1362 # interrupts. The card must then be the only user of that interrupt.
1363 # Interrupts cannot be shared when using PUC_FASTINTR.
1365 options PUC_FASTINTR
1368 # Network interfaces: `cx', `ed', `el', `ep', `ie', `is', `le', `lnc'
1370 # ar: Arnet SYNC/570i hdlc sync 2/4 port V.35/X.21 serial driver (requires sppp)
1371 # cm: Arcnet SMC COM90c26 / SMC COM90c56
1372 # (and SMC COM90c66 in '56 compatibility mode) adapters.
1373 # cs: IBM Etherjet and other Crystal Semi CS89x0-based adapters
1374 # cx: Cronyx/Sigma multiport sync/async (with Cisco or PPP framing)
1375 # ed: Western Digital and SMC 80xx; Novell NE1000 and NE2000; 3Com 3C503
1376 # el: 3Com 3C501 (slow!)
1378 # ex: Intel EtherExpress Pro/10 and other i82595-based adapters
1379 # fe: Fujitsu MB86960A/MB86965A Ethernet
1380 # ie: AT&T StarLAN 10 and EN100; 3Com 3C507; unknown NI5210; Intel EtherExpress
1381 # le: Digital Equipment EtherWorks 2 and EtherWorks 3 (DEPCA, DE100,
1382 # DE101, DE200, DE201, DE202, DE203, DE204, DE205, DE422)
1383 # lnc: Lance/PCnet cards (Isolan, Novell NE2100, NE32-VL, AMD Am7990 & Am79C960)
1384 # rdp: RealTek RTL 8002-based pocket ethernet adapters
1385 # sbni: Granch SBNI12-xx adapters
1386 # sbsh: Granch SBNI16 SHDSL modem PCI adapters
1387 # sr: RISCom/N2 hdlc sync 1/2 port V.35/X.21 serial driver (requires sppp)
1388 # wl: Lucent Wavelan (ISA card only).
1389 # awi: IEEE 802.11b PRISM I cards.
1390 # wi: Lucent WaveLAN/IEEE 802.11 PCMCIA adapters. Note: this supports both
1391 # the PCMCIA and ISA cards: the ISA card is really a PCMCIA to ISA
1392 # bridge with a PCMCIA adapter plugged into it.
1393 # an: Aironet 4500/4800 802.11 wireless adapters. Supports the PCMCIA,
1394 # PCI and ISA varieties.
1395 # xe: Xircom/Intel EtherExpress Pro100/16 PC Card ethernet controller.
1396 # ray: Raytheon Raylink 802.11 wireless NICs, OEM as Webgear Aviator 2.4GHz
1397 # oltr: Olicom ISA token-ring adapters OC-3115, OC-3117, OC-3118 and OC-3133
1398 # (no options needed)
1400 device ar0 at isa? port 0x300 irq 10 iomem 0xd0000
1401 device cm0 at isa? port 0x2e0 irq 9 iomem 0xdc000
1402 device cs0 at isa? port 0x300
1403 device cx0 at isa? port 0x240 irq 15 drq 7
1404 device ed0 at isa? port 0x280 irq 5 iomem 0xd8000
1405 device el0 at isa? port 0x300 irq 9
1408 device fe0 at isa? port 0x300
1409 device ie0 at isa? port 0x300 irq 5 iomem 0xd0000
1410 device ie1 at isa? port 0x360 irq 7 iomem 0xd0000
1411 device le0 at isa? port 0x300 irq 5 iomem 0xd0000
1412 device lnc0 at isa? port 0x280 irq 10 drq 0
1413 device rdp0 at isa? port 0x378 irq 7 flags 2
1414 device sbni0 at isa? port 0x210 irq 5 flags 0xefdead
1415 device sr0 at isa? port 0x300 irq 5 iomem 0xd0000
1416 device sn0 at isa? port 0x300 irq 10
1420 options WLCACHE # enables the signal-strength cache
1421 options WLDEBUG # enables verbose debugging output
1422 device wl0 at isa? port 0x300
1426 device oltr0 at isa?
1429 # ATM related options
1431 # The `en' device provides support for Efficient Networks (ENI)
1432 # ENI-155 PCI midway cards, and the Adaptec 155Mbps PCI ATM cards (ANA-59x0).
1434 # atm pseudo-device provides generic atm functions and is required for
1436 # NATM enables the netnatm protocol family that can be used to
1439 # the current driver supports only PVC operations (no atm-arp, no multicast).
1440 # for more details, please read the original documents at
1441 # http://www.ccrc.wustl.edu/pub/chuck/tech/bsdatm/bsdatm.html
1445 options NATM #native ATM
1448 # Audio drivers: `snd', `sb', `pas', `gus', `pca'
1450 # snd: Voxware sound support code
1451 # sb: SoundBlaster PCM - SoundBlaster, SB Pro, SB16, ProAudioSpectrum
1452 # sbxvi: SoundBlaster 16
1453 # sbmidi: SoundBlaster 16 MIDI interface
1454 # pas: ProAudioSpectrum PCM and MIDI
1455 # gus: Gravis Ultrasound - Ultrasound, Ultrasound 16, Ultrasound MAX
1456 # gusxvi: Gravis Ultrasound 16-bit PCM (do not use)
1457 # mss: Microsoft Sound System
1458 # css: Crystal Sound System (CSS 423x PnP)
1459 # sscape: Ensoniq Soundscape MIDI interface
1460 # sscape_mss: Ensoniq Soundscape PCM (requires sscape)
1461 # opl: Yamaha OPL-2 and OPL-3 FM - SB, SB Pro, SB 16, ProAudioSpectrum
1462 # uart: stand-alone 6850 UART for MIDI
1463 # mpu: Roland MPU-401 stand-alone card
1465 # Note: It has been reported that ISA DMA with the SoundBlaster will
1466 # lock up the machine (PR docs/5358). If this happens to you,
1467 # turning off USWC write posting in your machine's BIOS may fix
1470 # Beware! The addresses specified below are also hard-coded in
1471 # src/sys/i386/isa/sound/sound_config.h. If you change the values here, you
1472 # must also change the values in the include file.
1474 # pcm: PCM audio through various sound cards.
1476 # This has support for a large number of new audio cards, based on
1477 # CS423x, OPTi931, Yamaha OPL-SAx, and also for SB16, GusPnP.
1478 # For more information about this driver and supported cards,
1479 # see the pcm.4 man page.
1481 # The flags of the device tells the device a bit more info about the
1482 # device that normally is obtained through the PnP interface.
1483 # bit 2..0 secondary DMA channel;
1484 # bit 4 set if the board uses two dma channels;
1485 # bit 15..8 board type, overrides autodetection; leave it
1486 # zero if don't know what to put in (and you don't,
1487 # since this is unsupported at the moment...).
1489 # This driver will use the new PnP code if it's available.
1491 # pca: PCM audio through your PC speaker
1493 # If you have a GUS-MAX card and want to use the CS4231 codec on the
1494 # card the drqs for the gus max must be 8 bit (1, 2, or 3).
1496 # If you would like to use the full duplex option on the gus, then define
1497 # flags to be the ``read dma channel''.
1499 # options BROKEN_BUS_CLOCK #PAS-16 isn't working and OPTI chipset
1500 # options SYMPHONY_PAS #PAS-16 isn't working and SYMPHONY chipset
1501 # options EXCLUDE_SBPRO #PAS-16
1502 # options SBC_IRQ=5 #PAS-16. Must match irq on sb0 line.
1503 # PAS16: The order of the pas0/sb0/opl0 is important since the
1504 # sb emulation is enabled in the pas-16 attach.
1506 # To override the GUS defaults use:
1511 # The src/sys/i386/isa/sound/sound.doc has more information.
1513 # Controls all "VOXWARE" driver sound devices. See Luigi's driver
1514 # below for an alternate which may work better for some cards.
1517 #device pas0 at isa? port 0x388 irq 10 drq 6
1518 #device sb0 at isa? port 0x220 irq 5 drq 1
1519 #device sbxvi0 at isa? drq 5
1520 #device sbmidi0 at isa? port 0x330
1521 #device awe0 at isa? port 0x620
1522 #device gus0 at isa? port 0x220 irq 12 drq 1
1523 ##device gus0 at isa? port 0x220 irq 12 drq 1 flags 0x3
1524 #device mss0 at isa? port 0x530 irq 10 drq 1
1525 #device css0 at isa? port 0x534 irq 5 drq 1 flags 0x08
1526 #device sscape0 at isa? port 0x330 irq 9 drq 0
1527 #device trix0 at isa? port 0x330 irq 6 drq 0
1528 #device sscape_mss0 at isa? port 0x534 irq 5 drq 1
1529 #device opl0 at isa? port 0x388
1530 #device mpu0 at isa? port 0x330 irq 6 drq 0
1531 #device uart0 at isa? port 0x330 irq 5
1533 # The newpcm driver (use INSTEAD of snd0 and all VOXWARE drivers!).
1534 # Note that motherboard sound devices may require options PNPBIOS.
1536 # Supported cards include:
1537 # Creative SoundBlaster ISA PnP/non-PnP
1538 # Supports ESS and Avance ISA chips as well.
1539 # Gravis UltraSound ISA PnP/non-PnP
1540 # Crystal Semiconductor CS461x/428x PCI
1541 # Neomagic 256AV (ac97)
1542 # Most of the more common ISA/PnP sb/mss/ess compatible cards.
1544 # For non-pnp sound cards with no bridge drivers only:
1545 device pcm0 at isa? irq 10 drq 1 flags 0x0
1547 # For PnP/PCI sound cards
1550 # The bridge drivers for sound cards. These can be separately configured
1551 # for providing services to the likes of new-midi (not in the tree yet).
1552 # When used with 'device pcm' they also provide pcm sound services.
1554 # sbc: Creative SoundBlaster ISA PnP/non-PnP
1555 # Supports ESS and Avance ISA chips as well.
1556 # gusc: Gravis UltraSound ISA PnP/non-PnP
1557 # csa: Crystal Semiconductor CS461x/428x PCI
1559 # For non-PnP cards:
1560 device sbc0 at isa? port 0x220 irq 5 drq 1 flags 0x15
1561 device gusc0 at isa? port 0x220 irq 5 drq 1 flags 0x13
1563 # Not controlled by `snd'
1564 # XXX-Hiten The pca driver needs to readded back into LINT!
1565 # device pca0 at isa? port IO_TIMER1
1568 # Miscellaneous hardware:
1570 # mcd: Mitsumi CD-ROM using proprietary (non-ATAPI) interface
1571 # scd: Sony CD-ROM using proprietary (non-ATAPI) interface
1572 # wt: Wangtek and Archive QIC-02/QIC-36 tape drives
1573 # ctx: Cortex-I frame grabber
1574 # apm: Laptop Advanced Power Management (experimental)
1575 # spigot: The Creative Labs Video Spigot video-acquisition board
1576 # meteor: Matrox Meteor video capture board
1577 # bktr: Brooktree bt848/848a/849a/878/879 video capture and TV Tuner board
1578 # cy: Cyclades serial driver
1579 # dgb: Digiboard PC/Xi and PC/Xe series driver (ALPHA QUALITY!)
1580 # dgm: Digiboard PC/Xem driver
1581 # gp: National Instruments AT-GPIB and AT-GPIB/TNT board
1582 # asc: GI1904-based hand scanners, e.g. the Trust Amiscan Grey
1583 # gsc: Genius GS-4500 hand scanner.
1585 # labpc: National Instrument's Lab-PC and Lab-PC+
1586 # rc: RISCom/8 multiport card
1587 # rp: Comtrol Rocketport(ISA) - single card
1588 # tw: TW-523 power line interface for use with X-10 home control products
1589 # si: Specialix SI/XIO 4-32 port terminal multiplexor
1590 # spic: Sony Programmable I/O controller (VAIO notebooks)
1591 # stl: Stallion EasyIO and EasyConnection 8/32 (ISA and PCI), EasyConnection 8/64 PCI
1592 # stli: Stallion EasyConnection 8/64 ISA/EISA, ONboard, Brumby (intelligent)
1593 # nmdm: nullmodem terminal driver (see nmdm(4))
1596 # The flags takes the following meaning for apm0:
1597 # 0x0020 Statclock is broken.
1598 # If apm is omitted, some systems require sysctl -w kern.timecounter.method=1
1599 # for correct timekeeping.
1601 # Notes on the spigot:
1602 # The video spigot is at 0xad6. This port address can not be changed.
1603 # The irq values may only be 10, 11, or 15
1604 # I/O memory is an 8kb region. Possible values are:
1605 # 0a0000, 0a2000, ..., 0fffff, f00000, f02000, ..., ffffff
1606 # The start address must be on an even boundary.
1607 # Add the following option if you want to allow non-root users to be able
1608 # to access the spigot. This option is not secure because it allows users
1609 # direct access to the I/O page.
1610 # options SPIGOT_UNSECURE
1612 # Notes on the Comtrol Rocketport driver:
1614 # The exact values used for rp0 depend on how many boards you have
1615 # in the system. The manufacturer's sample configs are listed as:
1617 # Comtrol Rocketport ISA single card
1618 # device rp0 at isa? port 0x280
1620 # If instead you have two ISA cards, one installed at 0x100 and the
1621 # second installed at 0x180, then you should add the following to
1622 # your kernel configuration file:
1624 # device rp0 at isa? port 0x100
1625 # device rp1 at isa? port 0x180
1627 # For 4 ISA cards, it might be something like this:
1629 # device rp0 at isa? port 0x180
1630 # device rp1 at isa? port 0x100
1631 # device rp2 at isa? port 0x340
1632 # device rp3 at isa? port 0x240
1634 # And for PCI cards, you only need say:
1638 # Notes on the Digiboard driver:
1640 # The following flag values have special meanings:
1641 # 0x01 - alternate layout of pins (dgb & dgm)
1642 # 0x02 - use the windowed PC/Xe in 64K mode (dgb only)
1644 # Notes on the Specialix SI/XIO driver:
1645 # **This is NOT a Specialix supported Driver!**
1646 # The host card is memory, not IO mapped.
1647 # The Rev 1 host cards use a 64K chunk, on a 32K boundary.
1648 # The Rev 2 host cards use a 32K chunk, on a 32K boundary.
1649 # The cards can use an IRQ of 11, 12 or 15.
1651 # Notes on the Stallion stl and stli drivers:
1652 # See src/i386/isa/README.stl for complete instructions.
1653 # This is version 2.0.0, unsupported by Stallion.
1654 # The stl driver has a secondary IO port hard coded at 0x280. You need
1655 # to change src/i386/isa/stallion.c if you reconfigure this on the boards.
1656 # The "flags" and "iosiz" settings on the stli driver depend on the board:
1657 # EasyConnection 8/64 ISA: flags 23 iosiz 0x1000
1658 # EasyConnection 8/64 EISA: flags 24 iosiz 0x10000
1659 # EasyConnection 8/64 MCA: flags 25 iosiz 0x1000
1660 # ONboard ISA: flags 4 iosiz 0x10000
1661 # ONboard EISA: flags 7 iosiz 0x10000
1662 # ONboard MCA: flags 3 iosiz 0x10000
1663 # Brumby: flags 2 iosiz 0x4000
1664 # Stallion: flags 1 iosiz 0x10000
1665 # For the PCI cards, "device stl" will suffice.
1667 device mcd0 at isa? port 0x300 irq 10
1668 # for the Sony CDU31/33A CDROM
1669 device scd0 at isa? port 0x230
1670 # for the SoundBlaster 16 multicd - up to 4 devices
1671 device wt0 at isa? port 0x300 irq 5 drq 1
1672 device ctx0 at isa? port 0x230 iomem 0xd0000
1673 device spigot0 at isa? port 0xad6 irq 15 iomem 0xee000
1675 device gp0 at isa? port 0x2c0
1676 device gsc0 at isa? port IO_GSC1 drq 3
1677 device joy0 at isa? port IO_GAME
1678 device cy0 at isa? irq 10 iomem 0xd4000 iosiz 0x2000
1679 options CY_PCI_FASTINTR # Use with cy_pci unless irq is shared
1680 device dgb0 at isa? port 0x220 iomem 0xfc000
1681 options NDGBPORTS=16 # Defaults to 16*NDGB
1682 device dgm0 at isa? port 0x104 iomem 0xd0000
1683 device labpc0 at isa? port 0x260 irq 5
1684 device rc0 at isa? port 0x220 irq 12
1685 device rp0 at isa? port 0x280
1686 # the port and irq for tw0 are fictitious
1687 device tw0 at isa? port 0x380 irq 11
1688 device si0 at isa? iomem 0xd0000 irq 12
1689 device asc0 at isa? port IO_ASC1 drq 3 irq 10
1690 device spic0 at isa? irq 0 port 0x10a0
1691 device stl0 at isa? port 0x2a0 irq 10
1692 device stli0 at isa? port 0x2a0 iomem 0xcc000 flags 23 iosiz 0x1000
1693 # HOT1 Xilinx 6200 card (http://www.vcc.com/)
1695 # nullmodem terminal driver
1701 # The MCA bus device is `mca'. It provides auto-detection and
1702 # configuration support for all devices on the MCA bus.
1704 # The 'aha' device provides support for the Adaptec 1640
1706 # The 'bt' device provides support for various Buslogic/Bustek
1707 # and Storage Dimensions SCSI adapters.
1709 # The 'ep' device provides support for the 3Com 3C529 ethernet card.
1716 # The EISA bus device is `eisa'. It provides auto-detection and
1717 # configuration support for all devices on the EISA bus.
1719 # The `ahb' device provides support for the Adaptec 174X adapter.
1721 # The `ahc' device provides support for the Adaptec 274X and 284X
1722 # adapters. The 284X, although a VLB card, responds to EISA probes.
1724 # fea: DEC DEFEA EISA FDDI adapter
1731 # The aic7xxx driver will attempt to use memory mapped I/O for all PCI
1732 # controllers that have it configured only if this option is set. Unfortunately,
1733 # this doesn't work on some motherboards, which prevents it from being the
1735 options AHC_ALLOW_MEMIO
1737 # The adw driver will attempt to use memory mapped I/O for all PCI
1738 # controllers that have it configured only if this option is set.
1739 options ADW_ALLOW_MEMIO
1741 # By default, only 10 EISA slots are probed, since the slot numbers
1742 # above clash with the configuration address space of the PCI subsystem,
1743 # and the EISA probe is not very smart about this. This is sufficient
1744 # for most machines, but in particular the HP NetServer LC series comes
1745 # with an onboard AIC7770 dual-channel SCSI controller on EISA slot #11,
1746 # thus you need to bump this figure to 12 for them.
1747 options EISA_SLOTS=12
1750 # PCI devices & PCI options:
1752 # The main PCI bus device is `pci'. It provides auto-detection and
1753 # configuration support for all devices on the PCI bus, using either
1754 # configuration mode defined in the PCI specification.
1760 #Enable pci resources left off by a "lazy" BIOS:
1761 options PCI_ENABLE_IO_MODES
1762 #options PCI_QUIET #quiets PCI code on chipset settings
1763 options COMPAT_OLDPCI #FreeBSD 2.2 and 3.x compatibility shims
1770 # The `ahc' device provides support for the Adaptec 29/3940(U)(W)
1771 # and motherboard based AIC7870/AIC7880 adapters.
1773 # The 'ahd' device provides support for the Adaptec 79xx Ultra320
1774 # SCSI adapters. Options are documented in the ahd(4) manpage:
1776 options AHD_DEBUG_OPTS=0xffffffff
1777 options AHD_REG_PRETTY_PRINT
1778 #options AHD_TMODE_ENABLE=0xff
1780 # The `amd' device provides support for the AMD 53C974 SCSI host
1781 # adapter chip as found on devices such as the Tekram DC-390(T).
1783 # The `bge' device provides support for gigabit ethernet adapters
1784 # based on the Broadcom BCM570x familiy of controllers, including the
1785 # 3Com 3c996-T, the Netgear GA302T, the SysKonnect SK-9D21 and SK-9D41,
1786 # and the embedded gigE NICs on Dell PowerEdge 2550 servers.
1788 # The `ncr' device provides support for the NCR 53C810 and 53C825
1789 # self-contained SCSI host adapters.
1791 # The `isp' device provides support for the Qlogic ISP 1020, 1040
1792 # nd 1040B PCI SCSI host adapters, ISP 1240 Dual Ultra SCSI,
1793 # ISP 1080 and 1280 (Dual) Ultra2, ISP 12160 Ultra3 SCSI, as well as
1794 # the Qlogic ISP 2100 and ISP 2200 Fibre Channel Host Adapters.
1796 # The `dc' device provides support for PCI fast ethernet adapters
1797 # based on the DEC/Intel 21143 and various workalikes including:
1798 # the ADMtek AL981 Comet and AN985 Centaur, the ASIX Electronics
1799 # AX88140A and AX88141, the Davicom DM9100 and DM9102, the Lite-On
1800 # 82c168 and 82c169 PNIC, the Lite-On/Macronix LC82C115 PNIC II
1801 # and the Macronix 98713/98713A/98715/98715A/98725 PMAC. This driver
1802 # replaces the old al, ax, dm, pn and mx drivers. List of brands:
1803 # Digital DE500-BA, Kingston KNE100TX, D-Link DFE-570TX, SOHOware SFA110,
1804 # SVEC PN102-TX, CNet Pro110B, 120A, and 120B, Compex RL100-TX,
1805 # LinkSys LNE100TX, LNE100TX V2.0, Jaton XpressNet, Alfa Inc GFC2204,
1808 # The `de' device provides support for the Digital Equipment DC21040
1809 # self-contained Ethernet adapter.
1811 # The `em' device provides support for the Intel Pro/1000 Family of Gigabit
1812 # adapters (82542, 82543, 82544, 82540).
1814 # The `fxp' device provides support for the Intel EtherExpress Pro/100B
1815 # PCI Fast Ethernet adapters.
1817 # The `gx' device provides support for the Intel Pro/1000 Gigabit Ethernet
1818 # PCI adapters (82542, 82543-F, 82543-T).
1820 # The 'lge' device provides support for PCI gigabit ethernet adapters
1821 # based on the Level 1 LXT1001 NetCellerator chipset. This includes the
1822 # D-Link DGE-500SX, SMC TigerCard 1000 (SMC9462SX), and some Addtron cards.
1824 # The 'my' device provides support for the Myson MTD80X and MTD89X PCI
1825 # Fast Ethernet adapters.
1827 # The 'nge' device provides support for PCI gigabit ethernet adapters
1828 # based on the National Semiconductor DP83820 and DP83821 chipset. This
1829 # includes the SMC EZ Card 1000 (SMC9462TX), D-Link DGE-500T, Asante
1830 # FriendlyNet GigaNIX 1000TA and 1000TPC, the Addtron AEG320T, the
1831 # LinkSys EG1032 and EG1064, the Surecom EP-320G-TX and the Netgear GA622T.
1833 # The 'pcn' device provides support for PCI fast ethernet adapters based
1834 # on the AMD Am79c97x chipsets, including the PCnet/FAST, PCnet/FAST+,
1835 # PCnet/PRO and PCnet/Home. These were previously handled by the lnc
1836 # driver (and still will be if you leave this driver out of the kernel).
1838 # The 'rl' device provides support for PCI fast ethernet adapters based
1839 # on the RealTek 8129/8139 chipset. Note that the RealTek driver defaults
1840 # to using programmed I/O to do register accesses because memory mapped
1841 # mode seems to cause severe lockups on SMP hardware. This driver also
1842 # supports the Accton EN1207D `Cheetah' adapter, which uses a chip called
1843 # the MPX 5030/5038, which is either a RealTek in disguise or a RealTek
1844 # workalike. Note that the D-Link DFE-530TX+ uses the RealTek chipset
1845 # and is supported by this driver, not the 'vr' driver.
1847 # The 'sf' device provides support for Adaptec Duralink PCI fast
1848 # ethernet adapters based on the Adaptec AIC-6915 "starfire" controller.
1849 # This includes dual and quad port cards, as well as one 100baseFX card.
1850 # Most of these are 64-bit PCI devices, except for one single port
1851 # card which is 32-bit.
1853 # The 'ste' device provides support for adapters based on the Sundance
1854 # Technologies ST201 PCI fast ethernet controller. This includes the
1857 # The 'sis' device provides support for adapters based on the Silicon
1858 # Integrated Systems SiS 900 and SiS 7016 PCI fast ethernet controller
1861 # The 'sk' device provides support for the SysKonnect SK-984x series
1862 # PCI gigabit ethernet NICs. This includes the SK-9841 and SK-9842
1863 # single port cards (single mode and multimode fiber) and the
1864 # SK-9843 and SK-9844 dual port cards (also single mode and multimode).
1865 # The driver will autodetect the number of ports on the card and
1866 # attach each one as a separate network interface.
1868 # The 'ti' device provides support for PCI gigabit ethernet NICs based
1869 # on the Alteon Networks Tigon 1 and Tigon 2 chipsets. This includes the
1870 # Alteon AceNIC, the 3Com 3c985, the Netgear GA620 and various others.
1871 # Note that you will probably want to bump up NMBCLUSTERS a lot to use
1874 # The 'tl' device provides support for the Texas Instruments TNETE100
1875 # series 'ThunderLAN' cards and integrated ethernet controllers. This
1876 # includes several Compaq Netelligent 10/100 cards and the built-in
1877 # ethernet controllers in several Compaq Prosignia, Proliant and
1878 # Deskpro systems. It also supports several Olicom 10Mbps and 10/100
1881 # The `tx' device provides support for the SMC 9432 TX, BTX and FTX cards.
1883 # The `txp' device provides support for the 3Com 3cR990 "Typhoon"
1886 # The `vr' device provides support for various fast ethernet adapters
1887 # based on the VIA Technologies VT3043 `Rhine I' and VT86C100A `Rhine II'
1888 # chips, including the D-Link DFE530TX (see 'rl' for DFE530TX+), the Hawking
1889 # Technologies PN102TX, and the AOpen/Acer ALN-320.
1891 # The `vx' device provides support for the 3Com 3C590 and 3C595
1894 # The `wb' device provides support for various fast ethernet adapters
1895 # based on the Winbond W89C840F chip. Note: this is not the same as
1896 # the Winbond W89C940F, which is an NE2000 clone.
1898 # The `wx' device provides support for the Intel Gigabit Ethernet
1899 # PCI card (`Wiseman').
1901 # The `xl' device provides support for the 3Com 3c900, 3c905 and
1902 # 3c905B (Fast) Etherlink XL cards and integrated controllers. This
1903 # includes the integrated 3c905B-TX chips in certain Dell Optiplex and
1904 # Dell Precision desktop machines and the integrated 3c905-TX chips
1905 # in Dell Latitude laptop docking stations.
1907 # The `fpa' device provides support for the Digital DEFPA PCI FDDI
1908 # adapter. pseudo-device fddi is also needed.
1910 # The `meteor' device is a PCI video capture board. It can also have the
1911 # following options:
1912 # options METEOR_ALLOC_PAGES=xxx preallocate kernel pages for data entry
1913 # figure (ROWS*COLUMN*BYTES_PER_PIXEL*FRAME+PAGE_SIZE-1)/PAGE_SIZE
1914 # options METEOR_DEALLOC_PAGES remove all allocated pages on close(2)
1915 # options METEOR_DEALLOC_ABOVE=xxx remove all allocated pages above the
1916 # specified amount. If this value is below the allocated amount no action
1918 # options METEOR_SYSTEM_DEFAULT={METEOR_PAL|METEOR_NTSC|METEOR_SECAM}, used
1919 # for initialization of fps routine when a signal is not present.
1921 # The 'bktr' device is a PCI video capture device using the Brooktree
1922 # bt848/bt848a/bt849a/bt878/bt879 chipset. When used with a TV Tuner it forms a
1923 # TV card, eg Miro PC/TV, Hauppauge WinCast/TV WinTV, VideoLogic Captivator,
1924 # Intel Smart Video III, AverMedia, IMS Turbo, FlyVideo.
1926 # options OVERRIDE_CARD=xxx
1927 # options OVERRIDE_TUNER=xxx
1928 # options OVERRIDE_MSP=1
1929 # options OVERRIDE_DBX=1
1930 # These options can be used to override the auto detection
1931 # The current values for xxx are found in src/sys/dev/bktr/bktr_card.h
1932 # Using sysctl(8) run-time overrides on a per-card basis can be made
1934 # options BROOKTREE_SYSTEM_DEFAULT=BROOKTREE_PAL
1936 # options BROOKTREE_SYSTEM_DEFAULT=BROOKTREE_NTSC
1937 # Specifes the default video capture mode.
1938 # This is required for Dual Crystal (28&35Mhz) boards where PAL is used
1939 # to prevent hangs during initialisation. eg VideoLogic Captivator PCI.
1941 # options BKTR_USE_PLL
1942 # PAL or SECAM users who have a 28Mhz crystal (and no 35Mhz crystal)
1943 # must enable PLL mode with this option. eg some new Bt878 cards.
1945 # options BKTR_GPIO_ACCESS
1946 # This enable IOCTLs which give user level access to the GPIO port.
1948 # options BKTR_NO_MSP_RESET
1949 # Prevents the MSP34xx reset. Good if you initialise the MSP in another OS first
1951 # options BKTR_430_FX_MODE
1952 # Switch Bt878/879 cards into Intel 430FX chipset compatibility mode.
1954 # options BKTR_SIS_VIA_MODE
1955 # Switch Bt878/879 cards into SIS/VIA chipset compatibility mode which is
1956 # needed for some old SiS and VIA chipset motherboards.
1957 # This also allows Bt878/879 chips to work on old OPTi (<1997) chipset
1958 # motherboards and motherboards with bad or incomplete PCI 2.1 support.
1959 # As a rough guess, old = before 1998
1962 # The oltr driver supports the following Olicom PCI token-ring adapters
1963 # OC-3136, OC-3137, OC-3139, OC-3140, OC-3141, OC-3540, OC-3250
1965 device ahc # AHA2940 and onboard AIC7xxx devices
1966 device ahd # AIC79xx devices
1967 device amd # AMD 53C974 (Tekram DC-390(T))
1968 device isp # Qlogic family
1969 device ispfw # Firmware for QLogic HBAs
1970 device ncr # NCR/Symbios Logic
1971 device sym # NCR/Symbios Logic (newer chipsets)
1972 device trm # Tekram DC395U/UW/F and DC315U
1976 # ISP_TARGET_MODE - enable target mode operation
1977 #options ISP_TARGET_MODE=1
1979 # Options used in dev/sym/ (Symbios SCSI driver).
1980 #options SYM_SETUP_LP_PROBE_MAP #-Low Priority Probe Map (bits)
1981 # Allows the ncr to take precedence
1982 # 1 (1<<0) -> 810a, 860
1983 # 2 (1<<1) -> 825a, 875, 885, 895
1984 # 4 (1<<2) -> 895a, 896, 1510d
1985 #options SYM_SETUP_SCSI_DIFF #-HVD support for 825a, 875, 885
1986 # disabled:0 (default), enabled:1
1987 #options SYM_SETUP_PCI_PARITY #-PCI parity checking
1988 # disabled:0, enabled:1 (default)
1989 #options SYM_SETUP_MAX_LUN #-Number of LUNs supported
1990 # default:8, range:[1..64]
1993 # MII bus support is required for some PCI 10/100 ethernet NICs,
1994 # namely those which use MII-compliant transceivers or implement
1995 # tranceiver control interfaces that operate like an MII. Adding
1996 # "device miibus0" to the kernel config pulls in support for
1997 # the generic miibus API and all of the PHY drivers, including a
1998 # generic one for PHYs that aren't specifically handled by an
1999 # individual driver.
2002 # PCI Ethernet NICs that use the common MII bus controller code.
2003 device bfe # Broadcom BCM440x 10/100 Ethernet
2004 device dc # DEC/Intel 21143 and various workalikes
2005 device fxp # Intel EtherExpress PRO/100B (82557, 82558)
2006 device my # Myson Fast Ethernet (MTD80X, MTD89X)
2007 device pcn # AMD Am79C97x PCI 10/100 NICs
2008 device rl # RealTek 8129/8139
2009 device sbsh # Granch SBNI16 SHDSL modem
2010 device sf # Adaptec AIC-6915 (``Starfire'')
2011 device sis # Silicon Integrated Systems SiS 900/SiS 7016
2012 device ste # Sundance ST201 (D-Link DFE-550TX)
2013 device tl # Texas Instruments ThunderLAN
2014 device tx # SMC EtherPower II (83c17x ``EPIC'')
2015 device vr # VIA Rhine, Rhine II
2016 device wb # Winbond W89C840F
2017 device xl # 3Com 3c90x (``Boomerang'', ``Cyclone'')
2019 # PCI Ethernet NICs.
2020 device de # DEC/Intel DC21x4x (``Tulip'')
2021 device txp # 3Com 3cR990 (``Typhoon'')
2022 device vx # 3Com 3c590, 3c595 (``Vortex'')
2024 # Gigabit Ethernet NICs.
2025 device bge # Broadcom BCM570x (``Tigon III'')
2026 device em # Intel Pro/1000 (82542,82543,82544,82540)
2027 device gx # Intel Pro/1000 (82542, 82543)
2028 device lge # Level 1 LXT1001 (``Mercury'')
2029 device nge # NatSemi DP83820 and DP83821
2030 device sk # SysKonnect GEnesis
2031 device ti # Alteon (``Tigon I'', ``Tigon II'')
2037 #The oltr driver in the ISA section will also find PCI cards.
2041 # Brooktree driver has been ported to the new I2C framework. Thus,
2042 # you'll need to have the following 3 lines in the kernel config.
2046 # The iic and smb devices are only needed if you want to control other
2047 # I2C slaves connected to the external connector of some cards.
2054 # pccard: pccard slots
2055 # pcic: isa/pccard bridge (OLDCARD)
2056 # cardbus/cbb: cardbus bridge (NEWCARD)
2062 # You may need to reset all pccards after resuming
2063 options PCIC_RESUME_RESET # reset after resume
2066 # Laptop/Notebook options:
2069 # apm under `Miscellaneous hardware'
2072 # For older notebooks that signal a powerfail condition (external
2073 # power supply dropped, or battery state low) by issuing an NMI:
2075 options POWERFAIL_NMI # make it beep instead of panicing
2080 # System Management Bus support is provided by the 'smbus' device.
2081 # Access to the SMBus device is via the 'smb' device (/dev/smb*),
2082 # which is a child of the 'smbus' device.
2084 # Supported devices:
2085 # smb standard io through /dev/smb*
2087 # Supported SMB interfaces:
2088 # iicsmb I2C to SMB bridge with any iicbus interface
2089 # bktr brooktree848 I2C hardware interface
2090 # intpm Intel PIIX4 (82371AB, 82443MX) Power Management Unit
2091 # alpm Acer Aladdin-IV/V/Pro2 Power Management Unit
2092 # ichsmb Intel ICH SMBus controller chips (82801AA, 82801AB, 82801BA)
2093 # viapm VIA VT82C586B,596,686A and VT8233 SMBus controllers
2094 # amdpm AMD 756 Power Management Unit
2096 device smbus # Bus support, required for smb below.
2109 # Philips i2c bus support is provided by the `iicbus' device.
2111 # Supported devices:
2112 # ic i2c network interface
2113 # iic i2c standard io
2114 # iicsmb i2c to smb bridge. Allow i2c i/o with smb commands.
2116 # Supported interfaces:
2117 # pcf Philips PCF8584 ISA-bus controller
2118 # bktr brooktree848 I2C software interface
2121 # iicbb generic I2C bit-banging code (needed by lpbb, bktr)
2123 device iicbus # Bus support, required for ic/iic/iicsmb below.
2128 device iicsmb # smb over i2c bridge
2130 device pcf0 at isa? port 0x320 irq 5
2132 #---------------------------------------------------------------------------
2135 # See /usr/share/examples/isdn/ROADMAP for an introduction to isdn4bsd.
2137 # i4b passive ISDN cards support contains the following hardware drivers:
2139 # isic - Siemens/Infineon ISDN ISAC/HSCX/IPAC chipset driver
2140 # iwic - Winbond W6692 PCI bus ISDN S/T interface controller
2141 # ifpi - AVM Fritz!Card PCI driver
2142 # ifpi2 - AVM Fritz!Card PCI driver Version 2
2143 # ihfc - Cologne Chip HFC ISA/ISA-PnP chipset driver
2144 # ifpnp - AVM Fritz!Card PnP driver
2145 # itjc - Siemens ISAC / TJNet Tiger300/320 chipset
2147 # i4b active ISDN cards support contains the following hardware drivers:
2149 # iavc - AVM B1 PCI, AVM B1 ISA, AVM T1
2151 # Note that the ``options'' (if given) and ``device'' lines must BOTH
2152 # be uncommented to enable support for a given card !
2154 # In addition to a hardware driver (and probably an option) the mandatory
2155 # ISDN protocol stack devices and the mandatory support device must be
2156 # enabled as well as one or more devices from the optional devices section.
2158 #---------------------------------------------------------------------------
2159 # isic driver (Siemens/Infineon chipsets)
2160 #---------------------------------------------------------------------------
2162 # ISA bus non-PnP Cards:
2163 # ----------------------
2165 # Teles S0/8 or Niccy 1008
2167 device isic0 at isa? iomem 0xd0000 irq 5 flags 1
2169 # Teles S0/16 or Creatix ISDN-S0 or Niccy 1016
2171 #device isic0 at isa? port 0xd80 iomem 0xd0000 irq 5 flags 2
2175 #device isic0 at isa? port 0xd80 irq 5 flags 3
2177 # AVM A1 or AVM Fritz!Card
2179 #device isic0 at isa? port 0x340 irq 5 flags 4
2181 # USRobotics Sportster ISDN TA intern
2183 #device isic0 at isa? port 0x268 irq 5 flags 7
2185 # ITK ix1 Micro ( < V.3, non-PnP version )
2187 #device isic0 at isa? port 0x398 irq 10 flags 18
2191 #device isic0 at isa? port 0x360 irq 10 flags 20
2193 # ISA bus PnP Cards:
2194 # ------------------
2197 options TEL_S0_16_3_P
2200 # Creatix ISDN-S0 P&P
2204 # Dr. Neuhaus Niccy Go@
2208 # Sedlbauer Win Speed
2216 # ELSA QuickStep 1000pro ISA
2220 # ITK ix1 Micro ( V.3, PnP version )
2224 # Siemens I-Surf 2.0
2225 options SIEMENS_ISURF2
2228 # Asuscom ISDNlink 128K ISAC
2229 options ASUSCOM_IPAC
2232 # Eicon Diehl DIVA 2.0 and 2.02
2239 # ELSA MicroLink ISDN/PCI (same as ELSA QuickStep 1000pro PCI)
2243 #---------------------------------------------------------------------------
2244 # ifpnp driver for AVM Fritz!Card ISA PnP
2245 #---------------------------------------------------------------------------
2247 # AVM Fritz!Card ISA PnP
2250 #---------------------------------------------------------------------------
2251 # ihfc driver for Cologne Chip ISA chipsets (experimental!)
2252 #---------------------------------------------------------------------------
2254 # Teles 16.3c ISA PnP
2255 # AcerISDN P10 ISA PnP
2256 # TELEINT ISDN SPEED No.1
2259 #---------------------------------------------------------------------------
2260 # ifpi driver for AVM Fritz!Card PCI 1.0 (2.0 unsupported!)
2261 #---------------------------------------------------------------------------
2263 # AVM Fritz!Card PCI 1.0
2266 #---------------------------------------------------------------------------
2267 # ifpi2 driver for AVM Fritz!Card PCI 2.0
2268 #---------------------------------------------------------------------------
2270 # AVM Fritz!Card PCI 2.0
2273 #---------------------------------------------------------------------------
2274 # iwic driver for Winbond W6692 chipset
2275 #---------------------------------------------------------------------------
2277 # ASUSCOM P-IN100-ST-D (and other Winbond W6692 based cards)
2280 #---------------------------------------------------------------------------
2281 # itjc driver for Simens ISAC / TJNet Tiger300/320 chipset
2282 #---------------------------------------------------------------------------
2284 # Traverse Technologies NETjet-S
2288 #---------------------------------------------------------------------------
2289 # iavc driver (AVM active cards, needs i4bcapi driver!)
2290 #---------------------------------------------------------------------------
2292 pseudo-device "i4bcapi" 2
2297 # AVM B1 ISA bus (PnP mode not supported!)
2298 #device iavc0 at isa? port 0x150 irq 5
2301 # ISDN Protocol Stack (mandatory)
2302 # -------------------------------
2304 # Q.921 / layer 2 - i4b passive cards D channel handling
2305 pseudo-device "i4bq921"
2307 # Q.931 / layer 3 - i4b passive cards D channel handling
2308 pseudo-device "i4bq931"
2310 # layer 4 - i4b common passive and active card handling
2316 # userland driver to do ISDN tracing (for passive cards only)
2317 pseudo-device "i4btrc" 4
2319 # userland driver to control the whole thing (mandatory)
2320 pseudo-device "i4bctl"
2322 # userland driver for access to raw B channel
2323 pseudo-device "i4brbch" 4
2325 # userland driver for telephony
2326 pseudo-device "i4btel" 2
2328 # network driver for IP over raw HDLC ISDN
2329 pseudo-device "i4bipr" 4
2330 # enable VJ header compression detection for ipr i/f
2332 # enable logging of the first n IP packets to isdnd (n=32 here)
2335 # network driver for sync PPP over ISDN - requires sppp
2336 pseudo-device "i4bisppp" 4
2341 # Parallel port bus support is provided by the `ppbus' device.
2342 # Multiple devices may be attached to the parallel port, devices
2343 # are automatically probed and attached when found.
2345 # Supported devices:
2346 # vpo Iomega Zip Drive
2347 # Requires SCSI disk support ('scbus' and 'da'); the best
2348 # performance is achieved with ports in EPP 1.9 mode.
2349 # lpt Parallel Printer
2350 # plip Parallel network interface
2351 # ppi General-purpose I/O ("Geek Port") + IEEE1284 I/O
2352 # pps Pulse per second Timing Interface
2353 # lpbb Philips official parallel port I2C bit-banging interface
2355 # Supported interfaces:
2356 # ppc ISA-bus parallel port interfaces.
2359 options PPC_PROBE_CHIPSET # Enable chipset specific detection
2360 # (see flags in ppc(4))
2361 options DEBUG_1284 # IEEE1284 signaling protocol debug
2362 options PERIPH_1284 # Makes your computer act as a IEEE1284
2363 # compliant peripheral
2364 options DONTPROBE_1284 # Avoid boot detection of PnP parallel devices
2365 options VP0_DEBUG # ZIP/ZIP+ debug
2366 options LPT_DEBUG # Printer driver debug
2367 options PPC_DEBUG # Parallel chipset level debug
2368 options PLIP_DEBUG # Parallel network IP interface debug
2369 options PCFCLOCK_VERBOSE # Verbose pcfclock driver
2370 options PCFCLOCK_MAX_RETRIES=5 # Maximum read tries (default 10)
2372 device ppc0 at isa? irq 7
2382 # Kernel BOOTP support
2384 options BOOTP # Use BOOTP to obtain IP address/hostname
2385 options BOOTP_NFSROOT # NFS mount root filesystem using BOOTP info
2386 options BOOTP_NFSV3 # Use NFS v3 to NFS mount root
2387 options BOOTP_COMPAT # Workaround for broken bootp daemons.
2388 options BOOTP_WIRED_TO=fxp0 # Use interface fxp0 for BOOTP
2391 # Add tie-ins for a hardware watchdog. This only enable the hooks;
2392 # the user must still supply the actual driver.
2397 # Set the number of PV entries per process. Increasing this can
2398 # stop panics related to heavy use of shared memory. However, that can
2399 # (combined with large amounts of physical memory) cause panics at
2400 # boot time due the kernel running out of VM space.
2402 # If you're tweaking this, you might also want to increase the sysctls
2403 # "vm.v_free_min", "vm.v_free_reserved", and "vm.v_free_target".
2405 # The value below is the one more than the default.
2407 options PMAP_SHPGPERPROC=201
2410 # Change the size of the kernel virtual address space. Due to
2411 # constraints in loader(8) on i386, this must be a multiple of 4.
2412 # 256 = 1 GB of kernel address space. Increasing this also causes
2413 # a reduction of the address space in user processes. 512 splits
2414 # the 4GB cpu address space in half (2GB user, 2GB kernel).
2416 options KVA_PAGES=260
2419 # Disable swapping. This option removes all code which actually performs
2420 # swapping, so it's not possible to turn it back on at run-time.
2422 # This is sometimes usable for systems which don't have any swap space
2423 # (see also sysctls "vm.defer_swapspace_pageouts" and
2424 # "vm.disable_swapspace_pageouts")
2426 #options NO_SWAPPING
2428 # Set the number of sf_bufs to allocate. sf_bufs are virtual buffers
2429 # for sendfile(2) that are used to map file VM pages, and normally
2430 # default to a quantity that is roughly 16*MAXUSERS+512. You would
2431 # typically want about 4 of these for each simultaneous file send.
2433 options NSFBUFS=1024
2435 # Set the size of the buffer cache KVM reservation, in buffers. This is
2436 # scaled by approximately 16384 bytes. The system will auto-size the buffer
2437 # cache if this option is not specified.
2441 # Set the size of the mbuf KVM reservation, in clusters. This is scaled
2442 # by approximately 2048 bytes. The system will auto-size the mbuf area
2443 # to (512 + maxusers*16) if this option is not specified.
2444 # maxusers is in turn computed at boot time depending on available memory
2445 # or set to the value specified by "options MAXUSERS=x" (x=0 means
2447 # So, to take advantage of autoscaling, you have to remove both
2448 # NMBCLUSTERS and MAXUSERS (and NMBUFS) from your kernel config.
2450 options NMBCLUSTERS=1024
2452 # Set the number of mbufs available in the system. Each mbuf
2453 # consumes 256 bytes. The system will autosize this (to 4 times
2454 # the number of NMBCLUSTERS, depending on other constraints)
2455 # if this option is not specified.
2459 # Tune the kernel malloc area parameters. VM_KMEM_SIZE represents the
2460 # minimum, in bytes, and is typically (12*1024*1024) (12MB).
2461 # VM_KMEM_SIZE_MAX represents the maximum, typically 200 megabytes.
2462 # VM_KMEM_SIZE_SCALE can be set to adjust the auto-tuning factor, which
2463 # typically defaults to 4 (kernel malloc area size is physical memory
2464 # divided by the scale factor).
2466 options VM_KMEM_SIZE="(10*1024*1024)"
2467 options VM_KMEM_SIZE_MAX="(100*1024*1024)"
2468 options VM_KMEM_SIZE_SCALE="4"
2470 # Tune the buffer cache maximum KVA reservation, in bytes. The maximum is
2471 # usually capped at 200 MB, effecting machines with > 1GB of ram. Note
2472 # that the buffer cache only really governs write buffering and disk block
2473 # translations. The VM page cache is our primary disk cache and is not
2474 # effected by the size of the buffer cache.
2476 options VM_BCACHE_SIZE_MAX="(100*1024*1024)"
2478 # Tune the swap zone KVA reservation, in bytes. The default is typically
2479 # 70 MB, giving the system the ability to manage a maximum of 28GB worth
2480 # of swapped out data.
2482 options VM_SWZONE_SIZE_MAX="(50*1024*1024)"
2485 # Enable extra debugging code for locks. This stores the filename and
2486 # line of whatever acquired the lock in the lock itself, and change a
2487 # number of function calls to pass around the relevant data. This is
2488 # not at all useful unless you are debugging lock code. Also note
2489 # that it is likely to break e.g. fstat(1) unless you recompile your
2490 # userland with -DDEBUG_LOCKS as well.
2494 # Set the amount of time (in seconds) the system will wait before
2495 # rebooting automatically when a kernel panic occurs. If set to (-1),
2496 # the system will wait indefinitely until a key is pressed on the
2498 options PANIC_REBOOT_WAIT_TIME=16
2500 # Attempt to bypass the buffer cache and put data directly into the
2501 # userland buffer for read operation when O_DIRECT flag is set on the
2502 # file. Both offset and length of the read operation must be
2503 # multiples of the physical media sector size.
2507 # Specify a lower limit for the number of swap I/O buffers. They are
2508 # (among other things) used when bypassing the buffer cache due to
2509 # DIRECTIO kernel option enabled and O_DIRECT flag set on file.
2511 #options NSWBUF_MIN=120
2514 # SysVR4 ABI emulation
2516 # The svr4 ABI emulator can be statically compiled into the kernel or loaded as
2518 # The STREAMS network emulation code can also be compiled statically or as a
2519 # module. If loaded as a module, it must be loaded before the svr4 module
2520 # (the /usr/sbin/svr4 script does this for you). If compiling statically,
2521 # the `streams' pseudo-device must be configured into any kernel which also
2522 # specifies COMPAT_SVR4. It is possible to have a statically-configured
2523 # STREAMS device and a dynamically loadable svr4 emulator; the /usr/sbin/svr4
2524 # script understands that it doesn't need to load the `streams' module under
2525 # those circumstances.
2526 # Caveat: At this time, `options KTRACE' is required for the svr4 emulator
2527 # (whether static or dynamic).
2529 options COMPAT_SVR4 # build emulator statically
2530 options DEBUG_SVR4 # enable verbose debugging
2531 pseudo-device streams # STREAMS network driver (required for svr4).
2533 # The 'asr' driver provides support for current DPT/Adaptec SCSI RAID
2534 # controllers (SmartRAID V and VI and later).
2535 # These controllers require the CAM infrastructure.
2539 # The 'dpt' driver provides support for DPT controllers (http://www.dpt.com/).
2540 # These have hardware RAID-{0,1,5} support, and do multi-initiator I/O.
2541 # The DPT controllers are commonly re-licensed under other brand-names -
2542 # some controllers by Olivetti, Dec, HP, AT&T, SNI, AST, Alphatronic, NEC and
2543 # Compaq are actually DPT controllers.
2545 # See src/sys/dev/dpt for debugging and other subtle options.
2546 # DPT_MEASURE_PERFORMANCE Enables a set of (semi)invasive metrics. Various
2547 # instruments are enabled. The tools in
2548 # /usr/sbin/dpt_* assume these to be enabled.
2549 # DPT_HANDLE_TIMEOUTS Normally device timeouts are handled by the DPT.
2550 # If you ant the driver to handle timeouts, enable
2551 # this option. If your system is very busy, this
2552 # option will create more trouble than solve.
2553 # DPT_TIMEOUT_FACTOR Used to compute the excessive amount of time to
2554 # wait when timing out with the above option.
2555 # DPT_DEBUG_xxxx These are controllable from sys/dev/dpt/dpt.h
2556 # DPT_LOST_IRQ When enabled, will try, once per second, to catch
2557 # any interrupt that got lost. Seems to help in some
2558 # DPT-firmware/Motherboard combinations. Minimal
2559 # cost, great benefit.
2560 # DPT_RESET_HBA Make "reset" actually reset the controller
2561 # instead of fudging it. Only enable this if you
2562 # are 100% certain you need it.
2567 #!CAM# options DPT_MEASURE_PERFORMANCE
2568 #!CAM# options DPT_HANDLE_TIMEOUTS
2569 options DPT_TIMEOUT_FACTOR=4
2570 options DPT_LOST_IRQ
2571 options DPT_RESET_HBA
2572 options DPT_ALLOW_MEMIO
2575 # Compaq "CISS" RAID controllers (SmartRAID 5* series)
2576 # These controllers have a SCSI-like interface, and require the
2577 # CAM infrastructure.
2582 # Intel Integrated RAID controllers.
2583 # This driver was developed and is maintained by Intel. Contacts
2584 # at Intel for this driver are
2585 # "Kannanthanam, Boji T" <boji.t.kannanthanam@intel.com> and
2586 # "Leubner, Achim" <achim.leubner@intel.com>.
2591 # Mylex AcceleRAID and eXtremeRAID controllers with v6 and later
2592 # firmware. These controllers have a SCSI-like interface, and require
2593 # the CAM infrastructure.
2604 # General USB code (mandatory for USB)
2609 # Generic USB device driver
2611 # Human Interface Device (anything with buttons and dials)
2617 # USB Iomega Zip 100 Drive (Requires scbus and da)
2623 # USB Rio (MP3 Player)
2635 # ADMtek USB ethernet. Supports the LinkSys USB100TX,
2636 # the Billionton USB100, the Melco LU-ATX, the D-Link DSB-650TX
2637 # and the SMC 2202USB. Also works with the ADMtek AN986 Pegasus
2641 # CATC USB-EL1201A USB ethernet. Supports the CATC Netmate
2642 # and Netmate II, and the Belkin F5U111.
2645 # Kawasaki LSI ethernet. Supports the LinkSys USB10T,
2646 # Entrega USB-NET-E45, Peracom Ethernet Adapter, the
2647 # 3Com 3c19250, the ADS Technologies USB-10BT, the ATen UC10T,
2648 # the Netgear EA101, the D-Link DSB-650, the SMC 2102USB
2649 # and 2104USB, and the Corega USB-T.
2652 # debugging options for the USB subsystem
2657 options UKBD_DFLT_KEYMAP # specify the built-in keymap
2658 makeoptions UKBD_DFLT_KEYMAP=it.iso
2661 device firewire # Firewire bus code
2662 device sbp # SCSI over Firewire (Requires scbus and da)
2663 device fwe # Ethernet over Firewire (non-standard!)
2665 #####################################################################
2668 # This is a port of the openbsd crypto framework. Include this when
2669 # configuring IPsec and when you have a h/w crypto device to accelerate
2670 # user applications that link to openssl.
2672 # Drivers are ports from openbsd with some simple enhancements that have
2673 # been fed back to openbsd (and hopefully will be included).
2675 pseudo-device crypto # core crypto support
2676 pseudo-device cryptodev # /dev/crypto for access to h/w
2678 device rndtest # FIPS 140-2 entropy tester
2680 device hifn # Hifn 7951, 7781, etc.
2681 options HIFN_DEBUG # enable debugging support: hw.hifn.debug
2682 options HIFN_RNDTEST # enable rndtest support
2684 device ubsec # Broadcom 5501, 5601, 58xx
2685 options UBSEC_DEBUG # enable debugging support: hw.ubsec.debug
2686 options UBSEC_RNDTEST # enable rndtest support
2688 device acpica # basic ACPI support
2691 # mgadrm: AGP Matrox G200, G400, G450, G550
2692 # tdfxdrm: 3dfx Voodoo 3/4/5 and Banshee
2693 # r128drm: ATI Rage 128
2694 # radeondrm: ATI Radeon up to 9000/9100
2695 # DRM_DEBUG: include debug printfs, very slow
2697 # mga requires AGP in the kernel, and it is recommended
2698 # for AGP r128 and radeon cards.
2708 # Embedded system options:
2710 # An embedded system might want to run something other than init.
2711 options INIT_PATH="/sbin/init:/stand/sysinstall"
2714 options BUS_DEBUG # enable newbus debugging
2715 options DEBUG_VFS_LOCKS # enable vfs lock debugging
2716 options NPX_DEBUG # enable npx debugging (FPU/math emu)
2718 # More undocumented options for linting.
2719 # Note that documenting these are not considered an affront.
2721 options AHC_DUMP_EEPROM
2722 options AHC_TMODE_ENABLE
2723 options CAM_DEBUG_DELAY
2724 options CLUSTERDEBUG
2725 options COMPAT_LINUX
2726 options CPU_UPGRADE_HW_CACHE
2729 #options DISABLE_PSE
2730 options ENABLE_ALART
2731 options ENABLE_VFS_IOOPT
2733 options FB_INSTALL_CDEV
2734 options FE_8BIT_SUPPORT
2735 options I4B_SMP_WORKAROUND
2736 options I586_PMC_GUPROF=0x70000
2738 options KBDIO_DEBUG=2
2739 options KBD_MAXRETRY=4
2740 options KBD_MAXWAIT=6
2741 options KBD_RESETDELAY=201
2745 options NETATALKDEBUG
2746 #options OLTR_NO_BULLSEYE_MAC
2747 #options OLTR_NO_HAWKEYE_MAC
2748 #options OLTR_NO_TMS_MAC
2751 options SCSI_NCR_DEBUG
2752 options SCSI_NCR_MAX_SYNC=10000
2753 options SCSI_NCR_MAX_WIDE=1
2754 options SCSI_NCR_MYADDR=7
2755 options SC_DEBUG_LEVEL
2756 options SC_RENDER_DEBUG
2757 options SHOW_BUSYBUFS # List buffers that prevent root unmount
2758 options SIMPLELOCK_DEBUG
2760 options SLIP_IFF_OPTS
2762 options TIMER_FREQ="((14318182+6)/12)"
2763 options VFS_BIO_DEBUG