2 # GENERIC_SMP -- Generic kernel configuration file for DragonFly/i386
4 # Check the LINT configuration file in sys/config, for an
5 # exhaustive list of options.
16 makeoptions DEBUG=-g #Build kernel with gdb(1) debug symbols
18 options MATH_EMULATE #Support for x87 emulation
19 options INET #InterNETworking
20 options INET6 #IPv6 communications protocols
21 options HAMMER #Hammer Filesystem
22 options NULLFS #NULL filesystem
23 options FFS #Berkeley Fast Filesystem
24 options FFS_ROOT #FFS usable as root device [keep this!]
25 options SOFTUPDATES #Enable FFS soft updates support
26 options UFS_DIRHASH #Improve performance on big directories
27 options MFS #Memory Filesystem
28 options TMPFS #Temporary Filesystem
29 options MD_ROOT #MD is a potential root device
30 options NFS #Network Filesystem
31 options NFS_ROOT #NFS usable as root device, NFS required
32 options MSDOSFS #MSDOS Filesystem
33 options CD9660 #ISO 9660 Filesystem
34 options PROCFS #Process filesystem
35 options COMPAT_43 #Compatible with BSD 4.3 [KEEP THIS!]
36 options COMPAT_DF12 #Compatible with DragonFly 1.2 and earlier
37 options SCSI_DELAY=5000 #Delay (in ms) before probing SCSI
38 options DEVICE_POLLING # Support mixed interrupt-polling
39 # handling of network device drivers
40 options UCONSOLE #Allow users to grab the console
41 options USERCONFIG #boot -c editor
42 options VISUAL_USERCONFIG #visual boot -c editor
43 options KTRACE #ktrace(1) support
44 options SYSVSHM #SYSV-style shared memory
45 options SYSVMSG #SYSV-style message queues
46 options SYSVSEM #SYSV-style semaphores
47 options P1003_1B #Posix P1003_1B real-time extensions
48 options _KPOSIX_PRIORITY_SCHEDULING
49 options ICMP_BANDLIM #Rate limit bad replies
50 options KBD_INSTALL_CDEV # install a CDEV entry in /dev
51 options AHC_REG_PRETTY_PRINT # Print register bitfields in debug
52 # output. Adds ~128k to driver.
53 options AHD_REG_PRETTY_PRINT # Print register bitfields in debug
54 # output. Adds ~215k to driver.
55 options DSCHED_FQ # Fair-queuing disk scheduler
58 options ALTQ #alternate queueing
59 options ALTQ_CBQ #class based queueing
60 options ALTQ_RED #random early detection
61 options ALTQ_RIO #triple red for diffserv (needs RED)
62 options ALTQ_HFSC #hierarchical fair service curve
63 options ALTQ_PRIQ #priority queue
64 options ALTQ_FAIRQ #fair queueing
65 #options ALTQ_NOPCC #don't use processor cycle counter
66 #options ALTQ_DEBUG #for debugging
68 # SMP boxes with severely broken BIOSes which
69 # boot fine for non-SMP builds *might* work in SMP mode
70 # if you disable APIC_IO by setting the loader tunable
71 # hw.apic_io_enable to 0.
73 options SMP # Symmetric MultiProcessor Kernel
75 # Debugging for Development
85 device fdc0 at isa? port IO_FD1 irq 6 drq 2
86 device fd0 at fdc0 drive 0
87 device fd1 at fdc0 drive 1
89 # If you have a Toshiba Libretto with its Y-E Data PCMCIA floppy,
90 # don't use the above line for fdc0 but the following one:
93 # AHCI driver, this will override NATA for AHCI devices,
94 # both drivers may be included.
102 # NEW-ATA (NATA) and ATAPI devices
105 device natadisk # ATA disk drives
106 device natapicd # ATAPI CDROM drives
107 device natapifd # ATAPI floppy drives
108 device natapist # ATAPI tape drives
109 device natapicam # Emulate ATAPI devices as SCSI
110 device nataraid # support for ATA software RAID
112 device natausb # ATA-over-USB support
113 options ATA_STATIC_ID # Static device numbering
115 # LEGACY ATA and ATAPI devices
116 #device ata0 at isa? port IO_WD1 irq 14
117 #device ata1 at isa? port IO_WD2 irq 15
119 #device atadisk # ATA disk drives
120 #device atapicd # ATAPI CDROM drives
121 #device atapifd # ATAPI floppy drives
122 #device atapist # ATAPI tape drives
123 #device atapicam # Emulate ATAPI devices as SCSI via CAM
124 #options ATA_STATIC_ID #Static device numbering
127 device ahb # EISA AHA1742 family
128 device ahc # AHA2940 and onboard AIC7xxx devices
129 device ahd # AHA39320/29320 and onboard AIC79xx devices
130 device amd # AMD 53C974 (Tekram DC-390(T))
131 device isp # Qlogic family
132 device mpt # LSI-Logic MPT/Fusion
133 device ncr # NCR/Symbios Logic
134 device sym # NCR/Symbios Logic (newer chipsets)
135 options SYM_SETUP_LP_PROBE_MAP=0x40
136 # Allow ncr to attach legacy NCR devices when
137 # both sym and ncr are configured
145 device ncv # NCR 53C500
146 device nsp # Workbit Ninja SCSI-3
147 device stg # TMC 18C30/18C50
150 device scbus # SCSI bus (required)
151 device da # Direct Access (disks)
152 device sa # Sequential Access (tape etc)
154 device pass # Passthrough device (direct SCSI access)
155 device sg # Passthrough device (linux scsi generic)
157 # RAID controllers interfaced to the SCSI subsystem
158 device asr # DPT SmartRAID V, VI and Adaptec SCSI RAID
159 device dpt # DPT Smartcache - See LINT for options!
160 device iir # Intel Integrated RAID
161 device mly # Mylex AcceleRAID/eXtremeRAID
162 device ciss # Compaq SmartRAID 5* series
165 device aac # Adaptec FSA RAID, Dell PERC2/PERC3
166 #device aacp # SCSI passthrough for aac (requires CAM)
167 device ida # Compaq Smart RAID
168 device ips # IBM ServeRAID
169 device amr # AMI MegaRAID
170 device mlx # Mylex DAC960 family
171 device twe # 3ware Escalade 7000/8000's
172 device twa # 3ware 9000 series PATA/SATA RAID
173 device pst # Promise Supertrack
176 # Areca RAID (CAM is required).
178 device arcmsr # Areca SATA II RAID
180 # atkbdc0 controls both the keyboard and the PS/2 mouse
181 device atkbdc0 at isa? port IO_KBD
182 device atkbd0 at atkbdc? irq 1 flags 0x1
183 device psm0 at atkbdc? irq 12
187 # kbdmux is the keyboard multiplexer
190 # splash screen/screen saver
193 # syscons is the default console driver, resembling an SCO console
194 device sc0 at isa? flags 0x100
195 options SC_PIXEL_MODE # add support for the raster text mode
197 device agp # support several AGP chipsets
199 # Floating point support - do not disable.
200 device npx0 at nexus? port IO_NPX irq 13
202 # Power management support (see LINT for more options)
203 device apm0 at nexus? disable flags 0x20 # Advanced Power Management
205 # HW monitoring devices
206 device aps0 at isa? port 0x1600
207 device lm0 at isa? port 0x290
208 device it0 at isa? port 0x290
209 device it1 at isa? port 0xc00
210 device it2 at isa? port 0xd00
211 device it3 at isa? port 0x228
212 device wbsio0 at isa? port 0x2e
213 device wbsio1 at isa? port 0x4e
214 device lm#3 at wbsio?
216 # PCCARD (PCMCIA) support
222 device sio0 at isa? port IO_COM1 flags 0x10 irq 4
223 device sio1 at isa? port IO_COM2 irq 3
224 device sio2 at isa? disable port IO_COM3 irq 5
225 device sio3 at isa? disable port IO_COM4 irq 9
228 device ppc0 at isa? irq 7
229 device ppbus # Parallel port bus (required)
231 device plip # TCP/IP over parallel
232 device ppi # Parallel port interface device
233 #device vpo # Requires scbus and da
236 device de # DEC/Intel DC21x4x (``Tulip'')
237 device txp # 3Com 3cR990 (``Typhoon'')
238 device vx # 3Com 3c590, 3c595 (``Vortex'')
240 device em # Intel PRO/1000 adapter Gigabit Ethernet Card (``Wiseman'')
242 device ig_hal # Intel PRO/1000 hardware abstraction layer
244 # PCI Ethernet NICs that use the common MII bus controller code.
245 # NOTE: Be sure to keep the 'device miibus' line in order to use these NICs!
246 device miibus # MII bus support
247 device ae # Attansic/Atheros L2 Fast Ethernet
248 device age # Attansic/Atheros L1 Gigabit Ethernet
249 device alc # Atheros AR8131/AR8132
250 device ale # Atheros AR8121/AR8113/AR8114
251 device bce # Broadcom NetXtreme II Gigabit Ethernet
252 device bfe # Broadcom BCM440x 10/100 Ethernet
253 device dc # DEC/Intel 21143 and various workalikes
254 device et # Agere ET1310 10/100/1000 Ethernet
255 device fxp # Intel EtherExpress PRO/100B (82557, 82558)
256 device jme # JMicron Gigabit/Fast Ethernet
257 device pcn # AMD Am79C97x PCI 10/100 NICs
258 device rl # RealTek 8129/8139
259 device re # RealTek 8139C+/8169
260 device sf # Adaptec AIC-6915 (``Starfire'')
261 device sis # Silicon Integrated Systems SiS 900/SiS 7016
262 device sk # SysKonnect GEnesis, LinkSys EG1023, D-Link
263 device ste # Sundance ST201 (D-Link DFE-550TX)
264 device tl # Texas Instruments ThunderLAN
265 device tx # SMC EtherPower II (83c170 ``EPIC'')
266 device vge # VIA 612x GigE
267 device vr # VIA Rhine, Rhine II
268 device wb # Winbond W89C840F
269 device xl # 3Com 3c90x (``Boomerang'', ``Cyclone'')
270 device bge # Broadcom BCM570x (``Tigon III'')
271 device stge # Sundance/Tamarack TC9021 Gigabit Ethernet
272 device msk # Marvell/SysKonnect Yukon II Gigabit Ethernet
273 device nfe # NVIDIA nForce MCP 10/100/Gigabit Ethernet
276 # 'device ed' requires 'device miibus'
277 device ed0 at isa? disable port 0x280 irq 10 iomem 0xd8000
280 device fe0 at isa? disable port 0x300
285 options IEEE80211_DEBUG #enable debugging msgs
286 options IEEE80211_SUPPORT_MESH #enable 802.11s D3.0 support
287 options IEEE80211_SUPPORT_TDMA #enable TDMA support
288 device wlan # 802.11 support
289 device wlan_ccmp # 802.11 CCMP support
290 device wlan_tkip # 802.11 TKIP support
291 device wlan_wep # 802.11 WEP support
292 #device wlan_amrr # AMRR
294 # All wireless NICs require wlan and wlan_amrr
295 # Aironet 4500/4800 802.11 wireless NICs. Note: the declaration below will
296 # work for PCMCIA and PCI cards, as well as ISA cards set to ISA PnP
297 # mode (the factory default). If you set the switches on your ISA
298 # card for a manually chosen I/O address and IRQ, you must specify
299 # those parameters here.
301 device ral # Ralink Technology 802.11 wireless NIC
302 #device rtw # RealTek 802.11 wireless NIC
303 # WaveLAN/IEEE 802.11 wireless NICs. Note: the WaveLAN/IEEE really
304 # exists only as a PCMCIA device, so there is no ISA attachment needed
305 # and resources will always be dynamically assigned by the pccard code.
308 # The probe order of these is presently determined by i386/isa/isa_compat.c.
309 device ie0 at isa? disable port 0x300 irq 10 iomem 0xd0000
310 #device le0 at isa? disable port 0x300 irq 5 iomem 0xd0000
311 device lnc0 at isa? disable port 0x280 irq 10 drq 0
312 device cs0 at isa? disable port 0x300
313 device sn0 at isa? disable port 0x300 irq 10
315 # Pseudo devices - the number indicates how many units to allocate.
316 pseudo-device loop # Network loopback
317 pseudo-device ether # Ethernet support
318 pseudo-device sl 1 # Kernel SLIP
319 pseudo-device ppp 1 # Kernel PPP
320 pseudo-device tun # Packet tunnel.
321 pseudo-device pty # Pseudo-ttys (telnet etc)
322 pseudo-device md # Memory "disks"
323 pseudo-device gif # IPv6 and IPv4 tunneling
324 pseudo-device faith 1 # IPv6-to-IPv4 relaying (translation)
326 # The `bpf' pseudo-device enables the Berkeley Packet Filter.
327 # Be aware of the administrative consequences of enabling this!
328 pseudo-device bpf #Berkeley packet filter
330 pseudo-device crypto # core crypto support, used by wlan
331 pseudo-device cryptodev
334 device uhci # UHCI PCI->USB interface
335 device ohci # OHCI PCI->USB interface
336 device usb # USB Bus (required)
337 device ugen # Generic
338 device uhid # "Human Interface Devices"
339 device ukbd # Keyboard
340 device ulpt # Printer
341 device umass # Disks/Mass storage - Requires scbus and da
343 device uscanner # Scanners
344 device urio # Diamond Rio MP3 Player
345 # USB Ethernet, requires mii
346 device aue # ADMtek USB ethernet
347 device axe # ASIX Electronics USB Ethernet
348 device cue # CATC USB ethernet
349 device kue # Kawasaki LSI USB ethernet
350 device rue # RealTek 8150 based USB ethernet
351 # USB wireless NICs, requires wlan, wlan_amrr
352 #device rum # Ralink Technology RT2501USB/RT2601USB
353 #device ural # Ralink Technology RT2500USB
356 device firewire # FireWire bus code
357 device sbp # SCSI over FireWire (Requires scbus and da)
358 device fwe # Ethernet over FireWire (non-standard!)