2 * Copyright (c) 2014 Yandex LLC.
6 * Redistribution and use in source and binary forms, with or without
7 * modification, are permitted provided that the following conditions
9 * 1. Redistributions of source code must retain the above copyright
10 * notice, this list of conditions and the following disclaimer.
11 * 2. Redistributions in binary form must reproduce the above copyright
12 * notice, this list of conditions and the following disclaimer in the
13 * documentation and/or other materials provided with the distribution.
15 * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND
16 * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
17 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
18 * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE
19 * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
20 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
21 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
22 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
23 * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
24 * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
29 * The following set of constants are from Document SFF-8436
30 * "QSFP+ 10 Gbs 4X PLUGGABLE TRANSCEIVER" revision 4.8 dated October 31, 2013
32 * This SFF standard defines the following QSFP+ memory address module:
34 * 1) 256-byte addressable block and 128-byte pages
35 * 2) Lower 128-bytes addresses always refer to the same page
36 * 3) Upper address space may refer to different pages depending on
37 * "page select" byte value.
41 * Serial address 0xA02:
44 * 0-127 Monitoring data & page select byte
48 * 128-191 Base ID Fields
50 * 223-255 Vendor Specific ID
53 * 128-255 App-specific data
56 * 128-255 User EEPROM Data
58 * Page 03 (optional for Cable Assmeblies)
60 * 225-237 Vendor Specific
61 * 238-253 Channel Controls/Monitor
64 * All these values are read across an I2C (i squared C) bus.
67 #define SFF_8436_BASE 0xA0 /* Base address for all requests */
69 /* Table 17 - Lower Memory Map */
71 SFF_8436_MID = 0, /* Copy of SFF_8436_ID field */
72 SFF_8436_STATUS = 1, /* 2-bytes status (Table 18) */
73 SFF_8436_INTR_START = 3, /* Interrupt flags (Tables 19-21) */
74 SFF_8436_INTR_END = 21,
75 SFF_8436_MODMON_START = 22, /* Module monitors (Table 22 */
76 SFF_8436_TEMP = 22, /* Internally measured module temp */
77 SFF_8436_VCC = 26, /* Internally mesasure module
79 SFF_8436_MODMON_END = 33,
80 SFF_8436_CHMON_START = 34, /* Channel monitors (Table 23) */
81 SFF_8436_RX_CH1_MSB = 34, /* Internally measured RX input power */
82 SFF_8436_RX_CH1_LSB = 35, /* for channel 1 */
83 SFF_8436_RX_CH2_MSB = 36, /* Internally measured RX input power */
84 SFF_8436_RX_CH2_LSB = 37, /* for channel 2 */
85 SFF_8436_RX_CH3_MSB = 38, /* Internally measured RX input power */
86 SFF_8436_RX_CH3_LSB = 39, /* for channel 3 */
87 SFF_8436_RX_CH4_MSB = 40, /* Internally measured RX input power */
88 SFF_8436_RX_CH4_LSB = 41, /* for channel 4 */
89 SFF_8436_TX_CH1_MSB = 42, /* Internally measured TX bias */
90 SFF_8436_TX_CH1_LSB = 43, /* for channel 1 */
91 SFF_8436_TX_CH2_MSB = 44, /* Internally measured TX bias */
92 SFF_8436_TX_CH2_LSB = 45, /* for channel 2 */
93 SFF_8436_TX_CH3_MSB = 46, /* Internally measured TX bias */
94 SFF_8436_TX_CH3_LSB = 47, /* for channel 3 */
95 SFF_8436_TX_CH4_MSB = 48, /* Internally measured TX bias */
96 SFF_8436_TX_CH4_LSB = 49, /* for channel 4 */
97 SFF_8436_CHANMON_END = 81,
98 SFF_8436_CONTROL_START = 86, /* Control (Table 24) */
99 SFF_8436_CONTROL_END = 97,
100 SFF_8436_MASKS_START = 100, /* Module/channel masks (Table 25) */
101 SFF_8436_MASKS_END = 106,
102 SFF_8436_CHPASSWORD = 119, /* Password change entry (4 bytes) */
103 SFF_8436_PASSWORD = 123, /* Password entry area (4 bytes) */
104 SFF_8436_PAGESEL = 127, /* Page select byte */
107 /* Table 18 - Status Indicators bits */
108 /* Byte 1: all bits reserved */
111 #define SFF_8436_STATUS_FLATMEM (1 << 2) /* Upper memory flat or paged
112 * 0 = paging, 1=Page 0 only */
113 #define SFF_8436_STATUS_INTL (1 << 1) /* Digital state of the intL
114 * Interrupt output pin */
115 #define SFF_8436_STATUS_NOTREADY 1 /* Module has not yet achieved
116 * power up and memory data is not
117 * ready. 0=data is ready */
119 * Upper page 0 definitions:
120 * Table 29 - Serial ID: Data fields.
122 * Note that this table is mostly the same as used in SFF-8472.
123 * The only differenee is address shift: +128 bytes.
126 SFF_8436_ID = 128, /* Module Type (defined in sff8472.h) */
127 SFF_8436_EXT_ID = 129, /* Extended transceiver type
129 SFF_8436_CONNECTOR = 130, /* Connector type (Table 32) */
130 SFF_8436_TRANS_START = 131, /* Electric or Optical Compatibility
132 SFF_8436_CODE_E1040100G = 131, /* 10/40/100G Ethernet Compliance Code */
133 SFF_8436_CODE_SONET = 132, /* SONET Compliance codes */
134 SFF_8436_CODE_SATA = 133, /* SAS/SATA compliance codes */
135 SFF_8436_CODE_E1G = 134, /* Gigabit Ethernet Compliant codes */
136 SFF_8436_CODE_FC_START = 135, /* FC link/media/speed */
137 SFF_8436_CODE_FC_END = 138,
138 SFF_8436_TRANS_END = 138,
139 SFF_8436_ENCODING = 139, /* Encoding Code for high speed
140 * serial encoding algorithm (see
142 SFF_8436_BITRATE = 140, /* Nominal signaling rate, units
144 SFF_8436_RATEID = 141, /* Extended RateSelect Compliance
146 SFF_8436_LEN_SMF_KM = 142, /* Link length supported for single
147 * mode fiber, units of km */
148 SFF_8436_LEN_OM3 = 143, /* Link length supported for 850nm
149 * 50um multimode fiber, units of 2 m */
150 SFF_8436_LEN_OM2 = 144, /* Link length supported for 50 um
151 * OM2 fiber, units of 1 m */
152 SFF_8436_LEN_OM1 = 145, /* Link length supported for 1310 nm
153 * 50um multi-mode fiber, units of 1m*/
154 SFF_8436_LEN_ASM = 144, /* Link length of passive cable assembly
155 * Length is specified as in the INF
156 * 8074, units of 1m. 0 means this is
157 * not value assembly. Value of 255
158 * means thet the Module supports length
159 * greater than 254 m. */
160 SFF_8436_DEV_TECH = 147, /* Device/transmitter technology,
162 SFF_8436_VENDOR_START = 148, /* Vendor name, 16 bytes, padded
164 SFF_8436_VENDOR_END = 163,
165 SFF_8436_EXTMODCODE = 164, /* Extended module code, Table 164 */
166 SFF_8436_VENDOR_OUI_START = 165 , /* Vendor OUI SFP vendor IEEE
168 SFF_8436_VENDOR_OUI_END = 167,
169 SFF_8436_PN_START = 168, /* Vendor PN, padded right with 0x20 */
170 SFF_8436_PN_END = 183,
171 SFF_8436_REV_START = 184, /* Vendor Revision, padded right 0x20 */
172 SFF_8436_REV_END = 185,
173 SFF_8436_WAVELEN_START = 186, /* Wavelength Laser wavelength
174 * (Passive/Active Cable
175 * Specification Compliance) */
176 SFF_8436_WAVELEN_END = 189,
177 SFF_8436_MAX_CASE_TEMP = 190, /* Allows to specify maximum temp
178 * above 70C. Maximum case temperature is
179 * an 8-bit value in Degrees C. A value
180 *of 0 implies the standard 70C rating.*/
181 SFF_8436_CC_BASE = 191, /* CC_BASE Check code for Base ID
182 * Fields (first 63 bytes) */
183 /* Extended ID fields */
184 SFF_8436_OPTIONS_START = 192, /* Options Indicates which optional
185 * transceiver signals are
186 * implemented (see Table 39) */
187 SFF_8436_OPTIONS_END = 195,
188 SFF_8436_SN_START = 196, /* Vendor SN, riwght padded with 0x20 */
189 SFF_8436_SN_END = 211,
190 SFF_8436_DATE_START = 212, /* Vendor’s manufacturing date code
192 SFF_8436_DATE_END = 219,
193 SFF_8436_DIAG_TYPE = 220, /* Diagnostic Monitoring Type
194 * Indicates which type of
195 * diagnostic monitoring is
196 * implemented (if any) in the
197 * transceiver (see Table 41) */
199 SFF_8436_ENHANCED = 221, /* Enhanced Options Indicates which
200 * optional features are implemented
201 * (if any) in the transceiver
203 SFF_8636_BITRATE = 222, /* Nominal bit rate per channel, units
205 SFF_8436_CC_EXT = 223, /* Check code for the Extended ID
206 * Fields (bytes 192-222 incl) */
207 SFF_8436_VENDOR_RSRVD_START = 224,
208 SFF_8436_VENDOR_RSRVD_END = 255,