drivers/regulator/bd718x7-regulator.c

   1 // SPDX-License-Identifier: GPL-2.0
   2 // Copyright (C) 2018 ROHM Semiconductors
   3 // bd71837-regulator.c ROHM BD71837MWV/BD71847MWV regulator driver
   4
   5 #include <linux/delay.h>
   6 #include <linux/err.h>
   7 #include <linux/interrupt.h>
   8 #include <linux/kernel.h>
   9 #include <linux/mfd/rohm-bd718x7.h>
  10 #include <linux/module.h>
  11 #include <linux/of.h>
  12 #include <linux/platform_device.h>
  13 #include <linux/regulator/driver.h>
  14 #include <linux/regulator/machine.h>
  15 #include <linux/regulator/of_regulator.h>
  16 #include <linux/slab.h>
  17
  18 /* Typical regulator startup times as per data sheet in uS */
  19 #define BD71847_BUCK1_STARTUP_TIME 144
  20 #define BD71847_BUCK2_STARTUP_TIME 162
  21 #define BD71847_BUCK3_STARTUP_TIME 162
  22 #define BD71847_BUCK4_STARTUP_TIME 240
  23 #define BD71847_BUCK5_STARTUP_TIME 270
  24 #define BD71847_BUCK6_STARTUP_TIME 200
  25 #define BD71847_LDO1_STARTUP_TIME  440
  26 #define BD71847_LDO2_STARTUP_TIME  370
  27 #define BD71847_LDO3_STARTUP_TIME  310
  28 #define BD71847_LDO4_STARTUP_TIME  400
  29 #define BD71847_LDO5_STARTUP_TIME  530
  30 #define BD71847_LDO6_STARTUP_TIME  400
  31
  32 #define BD71837_BUCK1_STARTUP_TIME 160
  33 #define BD71837_BUCK2_STARTUP_TIME 180
  34 #define BD71837_BUCK3_STARTUP_TIME 180
  35 #define BD71837_BUCK4_STARTUP_TIME 180
  36 #define BD71837_BUCK5_STARTUP_TIME 160
  37 #define BD71837_BUCK6_STARTUP_TIME 240
  38 #define BD71837_BUCK7_STARTUP_TIME 220
  39 #define BD71837_BUCK8_STARTUP_TIME 200
  40 #define BD71837_LDO1_STARTUP_TIME  440
  41 #define BD71837_LDO2_STARTUP_TIME  370
  42 #define BD71837_LDO3_STARTUP_TIME  310
  43 #define BD71837_LDO4_STARTUP_TIME  400
  44 #define BD71837_LDO5_STARTUP_TIME  310
  45 #define BD71837_LDO6_STARTUP_TIME  400
  46 #define BD71837_LDO7_STARTUP_TIME  530
  47
  48 /*
  49  * BD718(37/47/50) have two "enable control modes". ON/OFF can either be
  50  * controlled by software - or by PMIC internal HW state machine. Whether
  51  * regulator should be under SW or HW control can be defined from device-tree.
  52  * Let's provide separate ops for regulators to use depending on the "enable
  53  * control mode".
  54  */
  55 #define BD718XX_HWOPNAME(swopname) swopname##_hwcontrol
  56
  57 #define BD718XX_OPS(name, _list_voltage, _map_voltage, _set_voltage_sel, \
  58                    _get_voltage_sel, _set_voltage_time_sel, _set_ramp_delay, \
  59                    _set_uvp, _set_ovp)                          \
  60 static const struct regulator_ops name = {                      \
  61         .enable = regulator_enable_regmap,                      \
  62         .disable = regulator_disable_regmap,                    \
  63         .is_enabled = regulator_is_enabled_regmap,              \
  64         .list_voltage = (_list_voltage),                        \
  65         .map_voltage = (_map_voltage),                          \
  66         .set_voltage_sel = (_set_voltage_sel),                  \
  67         .get_voltage_sel = (_get_voltage_sel),                  \
  68         .set_voltage_time_sel = (_set_voltage_time_sel),        \
  69         .set_ramp_delay = (_set_ramp_delay),                    \
  70         .set_under_voltage_protection = (_set_uvp),             \
  71         .set_over_voltage_protection = (_set_ovp),              \
  72 };                                                              \
  73                                                                 \
  74 static const struct regulator_ops BD718XX_HWOPNAME(name) = {    \
  75         .is_enabled = always_enabled_by_hwstate,                \
  76         .list_voltage = (_list_voltage),                        \
  77         .map_voltage = (_map_voltage),                          \
  78         .set_voltage_sel = (_set_voltage_sel),                  \
  79         .get_voltage_sel = (_get_voltage_sel),                  \
  80         .set_voltage_time_sel = (_set_voltage_time_sel),        \
  81         .set_ramp_delay = (_set_ramp_delay),                    \
  82         .set_under_voltage_protection = (_set_uvp),             \
  83         .set_over_voltage_protection = (_set_ovp),              \
  84 }                                                               \
  85
  86 /*
  87  * BUCK1/2/3/4
  88  * BUCK1RAMPRATE[1:0] BUCK1 DVS ramp rate setting
  89  * 00: 10.00mV/usec 10mV 1uS
  90  * 01: 5.00mV/usec      10mV 2uS
  91  * 10: 2.50mV/usec      10mV 4uS
  92  * 11: 1.25mV/usec      10mV 8uS
  93  */
  94 static const unsigned int bd718xx_ramp_delay[] = { 10000, 5000, 2500, 1250 };
  95
  96 /* These functions are used when regulators are under HW state machine control.
  97  * We assume PMIC is in RUN state because SW running and able to query the
  98  * status. Most of the regulators have fixed ON or OFF state at RUN/IDLE so for
  99  * them we just return a constant. BD71837 BUCK3 and BUCK4 are exceptions as
 100  * they support configuring the ON/OFF state for RUN.
 101  *
 102  * Note for next hacker - these PMICs have a register where the HW state can be
 103  * read. If assuming RUN appears to be false in your use-case - you can
 104  * implement state reading (although that is not going to be atomic) before
 105  * returning the enable state.
 106  */
 107 static int always_enabled_by_hwstate(struct regulator_dev *rdev)
 108 {
 109         return 1;
 110 }
 111
 112 static int never_enabled_by_hwstate(struct regulator_dev *rdev)
 113 {
 114         return 0;
 115 }
 116
 117 static int bd71837_get_buck34_enable_hwctrl(struct regulator_dev *rdev)
 118 {
 119         int ret;
 120         unsigned int val;
 121
 122         ret = regmap_read(rdev->regmap, rdev->desc->enable_reg, &val);
 123         if (ret)
 124                 return ret;
 125
 126         return !!(BD718XX_BUCK_RUN_ON & val);
 127 }
 128
 129 static void voltage_change_done(struct regulator_dev *rdev, unsigned int sel,
 130                                 unsigned int *mask)
 131 {
 132         int ret;
 133
 134         if (*mask) {
 135                 /*
 136                  * Let's allow scheduling as we use I2C anyways. We just need to
 137                  * guarantee minimum of 1ms sleep - it shouldn't matter if we
 138                  * exceed it due to the scheduling.
 139                  */
 140                 msleep(1);
 141
 142                 ret = regmap_clear_bits(rdev->regmap, BD718XX_REG_MVRFLTMASK2,
 143                                          *mask);
 144                 if (ret)
 145                         dev_err(&rdev->dev,
 146                                 "Failed to re-enable voltage monitoring (%d)\n",
 147                                 ret);
 148         }
 149 }
 150
 151 static int voltage_change_prepare(struct regulator_dev *rdev, unsigned int sel,
 152                                   unsigned int *mask)
 153 {
 154         int ret;
 155
 156         *mask = 0;
 157         if (rdev->desc->ops->is_enabled(rdev)) {
 158                 int now, new;
 159
 160                 now = rdev->desc->ops->get_voltage_sel(rdev);
 161                 if (now < 0)
 162                         return now;
 163
 164                 now = rdev->desc->ops->list_voltage(rdev, now);
 165                 if (now < 0)
 166                         return now;
 167
 168                 new = rdev->desc->ops->list_voltage(rdev, sel);
 169                 if (new < 0)
 170                         return new;
 171
 172                 /*
 173                  * If we increase LDO voltage when LDO is enabled we need to
 174                  * disable the power-good detection until voltage has reached
 175                  * the new level. According to HW colleagues the maximum time
 176                  * it takes is 1000us. I assume that on systems with light load
 177                  * this might be less - and we could probably use DT to give
 178                  * system specific delay value if performance matters.
 179                  *
 180                  * Well, knowing we use I2C here and can add scheduling delays
 181                  * I don't think it is worth the hassle and I just add fixed
 182                  * 1ms sleep here (and allow scheduling). If this turns out to
 183                  * be a problem we can change it to delay and make the delay
 184                  * time configurable.
 185                  */
 186                 if (new > now) {
 187                         int tmp;
 188                         int prot_bit;
 189                         int ldo_offset = rdev->desc->id - BD718XX_LDO1;
 190
 191                         prot_bit = BD718XX_LDO1_VRMON80 << ldo_offset;
 192                         ret = regmap_read(rdev->regmap, BD718XX_REG_MVRFLTMASK2,
 193                                           &tmp);
 194                         if (ret) {
 195                                 dev_err(&rdev->dev,
 196                                         "Failed to read voltage monitoring state\n");
 197                                 return ret;
 198                         }
 199
 200                         if (!(tmp & prot_bit)) {
 201                                 /* We disable protection if it was enabled... */
 202                                 ret = regmap_set_bits(rdev->regmap,
 203                                                       BD718XX_REG_MVRFLTMASK2,
 204                                                       prot_bit);
 205                                 /* ...and we also want to re-enable it */
 206                                 *mask = prot_bit;
 207                         }
 208                         if (ret) {
 209                                 dev_err(&rdev->dev,
 210                                         "Failed to stop voltage monitoring\n");
 211                                 return ret;
 212                         }
 213                 }
 214         }
 215
 216         return 0;
 217 }
 218
 219 static int bd718xx_set_voltage_sel_restricted(struct regulator_dev *rdev,
 220                                                     unsigned int sel)
 221 {
 222         int ret;
 223         int mask;
 224
 225         ret = voltage_change_prepare(rdev, sel, &mask);
 226         if (ret)
 227                 return ret;
 228
 229         ret = regulator_set_voltage_sel_regmap(rdev, sel);
 230         voltage_change_done(rdev, sel, &mask);
 231
 232         return ret;
 233 }
 234
 235 static int bd718xx_set_voltage_sel_pickable_restricted(
 236                 struct regulator_dev *rdev, unsigned int sel)
 237 {
 238         int ret;
 239         int mask;
 240
 241         ret = voltage_change_prepare(rdev, sel, &mask);
 242         if (ret)
 243                 return ret;
 244
 245         ret = regulator_set_voltage_sel_pickable_regmap(rdev, sel);
 246         voltage_change_done(rdev, sel, &mask);
 247
 248         return ret;
 249 }
 250
 251 static int bd71837_set_voltage_sel_pickable_restricted(
 252                 struct regulator_dev *rdev, unsigned int sel)
 253 {
 254         if (rdev->desc->ops->is_enabled(rdev))
 255                 return -EBUSY;
 256
 257         return regulator_set_voltage_sel_pickable_regmap(rdev, sel);
 258 }
 259
 260 /*
 261  * BD71837 BUCK1/2/3/4
 262  * BD71847 BUCK1/2
 263  * 0.70 to 1.30V (10mV step)
 264  */
 265 static const struct linear_range bd718xx_dvs_buck_volts[] = {
 266         REGULATOR_LINEAR_RANGE(700000, 0x00, 0x3C, 10000),
 267         REGULATOR_LINEAR_RANGE(1300000, 0x3D, 0x3F, 0),
 268 };
 269
 270 /*
 271  * BD71837 BUCK5
 272  * 0.7V to 1.35V  (range 0)
 273  * and
 274  * 0.675 to 1.325 (range 1)
 275  */
 276 static const struct linear_range bd71837_buck5_volts[] = {
 277         /* Ranges when VOLT_SEL bit is 0 */
 278         REGULATOR_LINEAR_RANGE(700000, 0x00, 0x03, 100000),
 279         REGULATOR_LINEAR_RANGE(1050000, 0x04, 0x05, 50000),
 280         REGULATOR_LINEAR_RANGE(1200000, 0x06, 0x07, 150000),
 281         /* Ranges when VOLT_SEL bit is 1  */
 282         REGULATOR_LINEAR_RANGE(675000, 0x0, 0x3, 100000),
 283         REGULATOR_LINEAR_RANGE(1025000, 0x4, 0x5, 50000),
 284         REGULATOR_LINEAR_RANGE(1175000, 0x6, 0x7, 150000),
 285 };
 286
 287 /*
 288  * Range selector for first 3 linear ranges is 0x0
 289  * and 0x1 for last 3 ranges.
 290  */
 291 static const unsigned int bd71837_buck5_volt_range_sel[] = {
 292         0x0, 0x0, 0x0, 0x80, 0x80, 0x80
 293 };
 294
 295 /*
 296  * BD71847 BUCK3
 297  */
 298 static const struct linear_range bd71847_buck3_volts[] = {
 299         /* Ranges when VOLT_SEL bits are 00 */
 300         REGULATOR_LINEAR_RANGE(700000, 0x00, 0x03, 100000),
 301         REGULATOR_LINEAR_RANGE(1050000, 0x04, 0x05, 50000),
 302         REGULATOR_LINEAR_RANGE(1200000, 0x06, 0x07, 150000),
 303         /* Ranges when VOLT_SEL bits are 01 */
 304         REGULATOR_LINEAR_RANGE(550000, 0x0, 0x7, 50000),
 305         /* Ranges when VOLT_SEL bits are 11 */
 306         REGULATOR_LINEAR_RANGE(675000, 0x0, 0x3, 100000),
 307         REGULATOR_LINEAR_RANGE(1025000, 0x4, 0x5, 50000),
 308         REGULATOR_LINEAR_RANGE(1175000, 0x6, 0x7, 150000),
 309 };
 310
 311 static const unsigned int bd71847_buck3_volt_range_sel[] = {
 312         0x0, 0x0, 0x0, 0x40, 0x80, 0x80, 0x80
 313 };
 314
 315 static const struct linear_range bd71847_buck4_volts[] = {
 316         REGULATOR_LINEAR_RANGE(3000000, 0x00, 0x03, 100000),
 317         REGULATOR_LINEAR_RANGE(2600000, 0x00, 0x03, 100000),
 318 };
 319
 320 static const unsigned int bd71847_buck4_volt_range_sel[] = { 0x0, 0x40 };
 321
 322 /*
 323  * BUCK6
 324  * 3.0V to 3.3V (step 100mV)
 325  */
 326 static const struct linear_range bd71837_buck6_volts[] = {
 327         REGULATOR_LINEAR_RANGE(3000000, 0x00, 0x03, 100000),
 328 };
 329
 330 /*
 331  * BD71837 BUCK7
 332  * BD71847 BUCK5
 333  * 000 = 1.605V
 334  * 001 = 1.695V
 335  * 010 = 1.755V
 336  * 011 = 1.8V (Initial)
 337  * 100 = 1.845V
 338  * 101 = 1.905V
 339  * 110 = 1.95V
 340  * 111 = 1.995V
 341  */
 342 static const unsigned int bd718xx_3rd_nodvs_buck_volts[] = {
 343         1605000, 1695000, 1755000, 1800000, 1845000, 1905000, 1950000, 1995000
 344 };
 345
 346 /*
 347  * BUCK8
 348  * 0.8V to 1.40V (step 10mV)
 349  */
 350 static const struct linear_range bd718xx_4th_nodvs_buck_volts[] = {
 351         REGULATOR_LINEAR_RANGE(800000, 0x00, 0x3C, 10000),
 352 };
 353
 354 /*
 355  * LDO1
 356  * 3.0 to 3.3V (100mV step)
 357  */
 358 static const struct linear_range bd718xx_ldo1_volts[] = {
 359         REGULATOR_LINEAR_RANGE(3000000, 0x00, 0x03, 100000),
 360         REGULATOR_LINEAR_RANGE(1600000, 0x00, 0x03, 100000),
 361 };
 362
 363 static const unsigned int bd718xx_ldo1_volt_range_sel[] = { 0x0, 0x20 };
 364
 365 /*
 366  * LDO2
 367  * 0.8 or 0.9V
 368  */
 369 static const unsigned int ldo_2_volts[] = {
 370         900000, 800000
 371 };
 372
 373 /*
 374  * LDO3
 375  * 1.8 to 3.3V (100mV step)
 376  */
 377 static const struct linear_range bd718xx_ldo3_volts[] = {
 378         REGULATOR_LINEAR_RANGE(1800000, 0x00, 0x0F, 100000),
 379 };
 380
 381 /*
 382  * LDO4
 383  * 0.9 to 1.8V (100mV step)
 384  */
 385 static const struct linear_range bd718xx_ldo4_volts[] = {
 386         REGULATOR_LINEAR_RANGE(900000, 0x00, 0x09, 100000),
 387 };
 388
 389 /*
 390  * LDO5 for BD71837
 391  * 1.8 to 3.3V (100mV step)
 392  */
 393 static const struct linear_range bd71837_ldo5_volts[] = {
 394         REGULATOR_LINEAR_RANGE(1800000, 0x00, 0x0F, 100000),
 395 };
 396
 397 /*
 398  * LDO5 for BD71837
 399  * 1.8 to 3.3V (100mV step)
 400  */
 401 static const struct linear_range bd71847_ldo5_volts[] = {
 402         REGULATOR_LINEAR_RANGE(1800000, 0x00, 0x0F, 100000),
 403         REGULATOR_LINEAR_RANGE(800000, 0x00, 0x0F, 100000),
 404 };
 405
 406 static const unsigned int bd71847_ldo5_volt_range_sel[] = { 0x0, 0x20 };
 407
 408 /*
 409  * LDO6
 410  * 0.9 to 1.8V (100mV step)
 411  */
 412 static const struct linear_range bd718xx_ldo6_volts[] = {
 413         REGULATOR_LINEAR_RANGE(900000, 0x00, 0x09, 100000),
 414 };
 415
 416 /*
 417  * LDO7
 418  * 1.8 to 3.3V (100mV step)
 419  */
 420 static const struct linear_range bd71837_ldo7_volts[] = {
 421         REGULATOR_LINEAR_RANGE(1800000, 0x00, 0x0F, 100000),
 422 };
 423
 424 struct reg_init {
 425         unsigned int reg;
 426         unsigned int mask;
 427         unsigned int val;
 428 };
 429 struct bd718xx_regulator_data {
 430         struct regulator_desc desc;
 431         const struct rohm_dvs_config dvs;
 432         const struct reg_init init;
 433         const struct reg_init *additional_inits;
 434         int additional_init_amnt;
 435 };
 436
 437 static int bd718x7_xvp_sanity_check(struct regulator_dev *rdev, int lim_uV,
 438                                     int severity)
 439 {
 440         /*
 441          * BD71837/47/50 ... (ICs supported by this driver) do not provide
 442          * warnings, only protection
 443          */
 444         if (severity != REGULATOR_SEVERITY_PROT) {
 445                 dev_err(&rdev->dev,
 446                         "Unsupported Under Voltage protection level\n");
 447                 return -EINVAL;
 448         }
 449
 450         /*
 451          * And protection limit is not changeable. It can only be enabled
 452          * or disabled
 453          */
 454         if (lim_uV)
 455                 return -EINVAL;
 456
 457         return 0;
 458 }
 459
 460 static int bd718x7_set_ldo_uvp(struct regulator_dev *rdev, int lim_uV,
 461                                int severity, bool enable)
 462 {
 463         int ldo_offset = rdev->desc->id - BD718XX_LDO1;
 464         int prot_bit, ret;
 465
 466         ret = bd718x7_xvp_sanity_check(rdev, lim_uV, severity);
 467         if (ret)
 468                 return ret;
 469
 470         prot_bit = BD718XX_LDO1_VRMON80 << ldo_offset;
 471
 472         if (enable)
 473                 return regmap_clear_bits(rdev->regmap, BD718XX_REG_MVRFLTMASK2,
 474                                          prot_bit);
 475
 476         return regmap_set_bits(rdev->regmap, BD718XX_REG_MVRFLTMASK2,
 477                                prot_bit);
 478 }
 479
 480 static int bd718x7_get_buck_prot_reg(int id, int *reg)
 481 {
 482
 483         if (id > BD718XX_BUCK8) {
 484                 WARN_ON(id > BD718XX_BUCK8);
 485                 return -EINVAL;
 486         }
 487
 488         if (id > BD718XX_BUCK4)
 489                 *reg = BD718XX_REG_MVRFLTMASK0;
 490         else
 491                 *reg = BD718XX_REG_MVRFLTMASK1;
 492
 493         return 0;
 494 }
 495
 496 static int bd718x7_get_buck_ovp_info(int id, int *reg, int *bit)
 497 {
 498         int ret;
 499
 500         ret = bd718x7_get_buck_prot_reg(id, reg);
 501         if (ret)
 502                 return ret;
 503
 504         *bit = BIT((id % 4) * 2 + 1);
 505
 506         return 0;
 507 }
 508
 509 static int bd718x7_get_buck_uvp_info(int id, int *reg, int *bit)
 510 {
 511         int ret;
 512
 513         ret = bd718x7_get_buck_prot_reg(id, reg);
 514         if (ret)
 515                 return ret;
 516
 517         *bit = BIT((id % 4) * 2);
 518
 519         return 0;
 520 }
 521
 522 static int bd718x7_set_buck_uvp(struct regulator_dev *rdev, int lim_uV,
 523                                 int severity, bool enable)
 524 {
 525         int bit, reg, ret;
 526
 527         ret = bd718x7_xvp_sanity_check(rdev, lim_uV, severity);
 528         if (ret)
 529                 return ret;
 530
 531         ret = bd718x7_get_buck_uvp_info(rdev->desc->id, &reg, &bit);
 532         if (ret)
 533                 return ret;
 534
 535         if (enable)
 536                 return regmap_clear_bits(rdev->regmap, reg, bit);
 537
 538         return regmap_set_bits(rdev->regmap, reg, bit);
 539
 540 }
 541
 542 static int bd718x7_set_buck_ovp(struct regulator_dev *rdev, int lim_uV,
 543                                 int severity,
 544                                 bool enable)
 545 {
 546         int bit, reg, ret;
 547
 548         ret = bd718x7_xvp_sanity_check(rdev, lim_uV, severity);
 549         if (ret)
 550                 return ret;
 551
 552         ret = bd718x7_get_buck_ovp_info(rdev->desc->id, &reg, &bit);
 553         if (ret)
 554                 return ret;
 555
 556         if (enable)
 557                 return regmap_clear_bits(rdev->regmap, reg, bit);
 558
 559         return regmap_set_bits(rdev->regmap, reg, bit);
 560 }
 561
 562 /*
 563  * OPS common for BD71847 and BD71850
 564  */
 565 BD718XX_OPS(bd718xx_pickable_range_ldo_ops,
 566             regulator_list_voltage_pickable_linear_range, NULL,
 567             bd718xx_set_voltage_sel_pickable_restricted,
 568             regulator_get_voltage_sel_pickable_regmap, NULL, NULL,
 569             bd718x7_set_ldo_uvp, NULL);
 570
 571 /* BD71847 and BD71850 LDO 5 is by default OFF at RUN state */
 572 static const struct regulator_ops bd718xx_ldo5_ops_hwstate = {
 573         .is_enabled = never_enabled_by_hwstate,
 574         .list_voltage = regulator_list_voltage_pickable_linear_range,
 575         .set_voltage_sel = bd718xx_set_voltage_sel_pickable_restricted,
 576         .get_voltage_sel = regulator_get_voltage_sel_pickable_regmap,
 577         .set_under_voltage_protection = bd718x7_set_ldo_uvp,
 578 };
 579
 580 BD718XX_OPS(bd718xx_pickable_range_buck_ops,
 581             regulator_list_voltage_pickable_linear_range, NULL,
 582             regulator_set_voltage_sel_pickable_regmap,
 583             regulator_get_voltage_sel_pickable_regmap,
 584             regulator_set_voltage_time_sel, NULL, bd718x7_set_buck_uvp,
 585             bd718x7_set_buck_ovp);
 586
 587 BD718XX_OPS(bd718xx_ldo_regulator_ops, regulator_list_voltage_linear_range,
 588             NULL, bd718xx_set_voltage_sel_restricted,
 589             regulator_get_voltage_sel_regmap, NULL, NULL, bd718x7_set_ldo_uvp,
 590             NULL);
 591
 592 BD718XX_OPS(bd718xx_ldo_regulator_nolinear_ops, regulator_list_voltage_table,
 593             NULL, bd718xx_set_voltage_sel_restricted,
 594             regulator_get_voltage_sel_regmap, NULL, NULL, bd718x7_set_ldo_uvp,
 595             NULL);
 596
 597 BD718XX_OPS(bd718xx_buck_regulator_ops, regulator_list_voltage_linear_range,
 598             NULL, regulator_set_voltage_sel_regmap,
 599             regulator_get_voltage_sel_regmap, regulator_set_voltage_time_sel,
 600             NULL, bd718x7_set_buck_uvp, bd718x7_set_buck_ovp);
 601
 602 BD718XX_OPS(bd718xx_buck_regulator_nolinear_ops, regulator_list_voltage_table,
 603             regulator_map_voltage_ascend, regulator_set_voltage_sel_regmap,
 604             regulator_get_voltage_sel_regmap, regulator_set_voltage_time_sel,
 605             NULL, bd718x7_set_buck_uvp, bd718x7_set_buck_ovp);
 606
 607 /*
 608  * OPS for BD71837
 609  */
 610 BD718XX_OPS(bd71837_pickable_range_ldo_ops,
 611             regulator_list_voltage_pickable_linear_range, NULL,
 612             bd71837_set_voltage_sel_pickable_restricted,
 613             regulator_get_voltage_sel_pickable_regmap, NULL, NULL,
 614             bd718x7_set_ldo_uvp, NULL);
 615
 616 BD718XX_OPS(bd71837_pickable_range_buck_ops,
 617             regulator_list_voltage_pickable_linear_range, NULL,
 618             bd71837_set_voltage_sel_pickable_restricted,
 619             regulator_get_voltage_sel_pickable_regmap,
 620             regulator_set_voltage_time_sel, NULL, bd718x7_set_buck_uvp,
 621             bd718x7_set_buck_ovp);
 622
 623 BD718XX_OPS(bd71837_ldo_regulator_ops, regulator_list_voltage_linear_range,
 624             NULL, rohm_regulator_set_voltage_sel_restricted,
 625             regulator_get_voltage_sel_regmap, NULL, NULL, bd718x7_set_ldo_uvp,
 626             NULL);
 627
 628 BD718XX_OPS(bd71837_ldo_regulator_nolinear_ops, regulator_list_voltage_table,
 629             NULL, rohm_regulator_set_voltage_sel_restricted,
 630             regulator_get_voltage_sel_regmap, NULL, NULL, bd718x7_set_ldo_uvp,
 631             NULL);
 632
 633 BD718XX_OPS(bd71837_buck_regulator_ops, regulator_list_voltage_linear_range,
 634             NULL, rohm_regulator_set_voltage_sel_restricted,
 635             regulator_get_voltage_sel_regmap, regulator_set_voltage_time_sel,
 636             NULL, bd718x7_set_buck_uvp, bd718x7_set_buck_ovp);
 637
 638 BD718XX_OPS(bd71837_buck_regulator_nolinear_ops, regulator_list_voltage_table,
 639             regulator_map_voltage_ascend, rohm_regulator_set_voltage_sel_restricted,
 640             regulator_get_voltage_sel_regmap, regulator_set_voltage_time_sel,
 641             NULL, bd718x7_set_buck_uvp, bd718x7_set_buck_ovp);
 642 /*
 643  * BD71837 bucks 3 and 4 support defining their enable/disable state also
 644  * when buck enable state is under HW state machine control. In that case the
 645  * bit [2] in CTRL register is used to indicate if regulator should be ON.
 646  */
 647 static const struct regulator_ops bd71837_buck34_ops_hwctrl = {
 648         .is_enabled = bd71837_get_buck34_enable_hwctrl,
 649         .list_voltage = regulator_list_voltage_linear_range,
 650         .set_voltage_sel = regulator_set_voltage_sel_regmap,
 651         .get_voltage_sel = regulator_get_voltage_sel_regmap,
 652         .set_voltage_time_sel = regulator_set_voltage_time_sel,
 653         .set_ramp_delay = regulator_set_ramp_delay_regmap,
 654         .set_under_voltage_protection = bd718x7_set_buck_uvp,
 655         .set_over_voltage_protection = bd718x7_set_buck_ovp,
 656 };
 657
 658 /*
 659  * OPS for all of the ICs - BD718(37/47/50)
 660  */
 661 BD718XX_OPS(bd718xx_dvs_buck_regulator_ops, regulator_list_voltage_linear_range,
 662             NULL, regulator_set_voltage_sel_regmap,
 663             regulator_get_voltage_sel_regmap, regulator_set_voltage_time_sel,
 664             regulator_set_ramp_delay_regmap, bd718x7_set_buck_uvp,
 665             bd718x7_set_buck_ovp);
 666
 667
 668
 669 /*
 670  * There is a HW quirk in BD71837. The shutdown sequence timings for
 671  * bucks/LDOs which are controlled via register interface are changed.
 672  * At PMIC poweroff the voltage for BUCK6/7 is cut immediately at the
 673  * beginning of shut-down sequence. As bucks 6 and 7 are parent
 674  * supplies for LDO5 and LDO6 - this causes LDO5/6 voltage
 675  * monitoring to errorneously detect under voltage and force PMIC to
 676  * emergency state instead of poweroff. In order to avoid this we
 677  * disable voltage monitoring for LDO5 and LDO6
 678  */
 679 static const struct reg_init bd71837_ldo5_inits[] = {
 680         {
 681                 .reg = BD718XX_REG_MVRFLTMASK2,
 682                 .mask = BD718XX_LDO5_VRMON80,
 683                 .val = BD718XX_LDO5_VRMON80,
 684         },
 685 };
 686
 687 static const struct reg_init bd71837_ldo6_inits[] = {
 688         {
 689                 .reg = BD718XX_REG_MVRFLTMASK2,
 690                 .mask = BD718XX_LDO6_VRMON80,
 691                 .val = BD718XX_LDO6_VRMON80,
 692         },
 693 };
 694
 695 static int buck_set_hw_dvs_levels(struct device_node *np,
 696                             const struct regulator_desc *desc,
 697                             struct regulator_config *cfg)
 698 {
 699         struct bd718xx_regulator_data *data;
 700
 701         data = container_of(desc, struct bd718xx_regulator_data, desc);
 702
 703         return rohm_regulator_set_dvs_levels(&data->dvs, np, desc, cfg->regmap);
 704 }
 705
 706 static const struct regulator_ops *bd71847_swcontrol_ops[] = {
 707         &bd718xx_dvs_buck_regulator_ops, &bd718xx_dvs_buck_regulator_ops,
 708         &bd718xx_pickable_range_buck_ops, &bd718xx_pickable_range_buck_ops,
 709         &bd718xx_buck_regulator_nolinear_ops, &bd718xx_buck_regulator_ops,
 710         &bd718xx_pickable_range_ldo_ops, &bd718xx_ldo_regulator_nolinear_ops,
 711         &bd718xx_ldo_regulator_ops, &bd718xx_ldo_regulator_ops,
 712         &bd718xx_pickable_range_ldo_ops, &bd718xx_ldo_regulator_ops,
 713 };
 714
 715 static const struct regulator_ops *bd71847_hwcontrol_ops[] = {
 716         &BD718XX_HWOPNAME(bd718xx_dvs_buck_regulator_ops),
 717         &BD718XX_HWOPNAME(bd718xx_dvs_buck_regulator_ops),
 718         &BD718XX_HWOPNAME(bd718xx_pickable_range_buck_ops),
 719         &BD718XX_HWOPNAME(bd718xx_pickable_range_buck_ops),
 720         &BD718XX_HWOPNAME(bd718xx_buck_regulator_nolinear_ops),
 721         &BD718XX_HWOPNAME(bd718xx_buck_regulator_ops),
 722         &BD718XX_HWOPNAME(bd718xx_pickable_range_ldo_ops),
 723         &BD718XX_HWOPNAME(bd718xx_ldo_regulator_nolinear_ops),
 724         &BD718XX_HWOPNAME(bd718xx_ldo_regulator_ops),
 725         &BD718XX_HWOPNAME(bd718xx_ldo_regulator_ops),
 726         &bd718xx_ldo5_ops_hwstate,
 727         &BD718XX_HWOPNAME(bd718xx_ldo_regulator_ops),
 728 };
 729
 730 static struct bd718xx_regulator_data bd71847_regulators[] = {
 731         {
 732                 .desc = {
 733                         .name = "buck1",
 734                         .of_match = of_match_ptr("BUCK1"),
 735                         .regulators_node = of_match_ptr("regulators"),
 736                         .id = BD718XX_BUCK1,
 737                         .type = REGULATOR_VOLTAGE,
 738                         .n_voltages = BD718XX_DVS_BUCK_VOLTAGE_NUM,
 739                         .linear_ranges = bd718xx_dvs_buck_volts,
 740                         .n_linear_ranges =
 741                                 ARRAY_SIZE(bd718xx_dvs_buck_volts),
 742                         .vsel_reg = BD718XX_REG_BUCK1_VOLT_RUN,
 743                         .vsel_mask = DVS_BUCK_RUN_MASK,
 744                         .enable_reg = BD718XX_REG_BUCK1_CTRL,
 745                         .enable_mask = BD718XX_BUCK_EN,
 746                         .enable_time = BD71847_BUCK1_STARTUP_TIME,
 747                         .owner = THIS_MODULE,
 748                         .ramp_delay_table = bd718xx_ramp_delay,
 749                         .n_ramp_values = ARRAY_SIZE(bd718xx_ramp_delay),
 750                         .ramp_reg = BD718XX_REG_BUCK1_CTRL,
 751                         .ramp_mask = BUCK_RAMPRATE_MASK,
 752                         .of_parse_cb = buck_set_hw_dvs_levels,
 753                 },
 754                 .dvs = {
 755                         .level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE |
 756                                      ROHM_DVS_LEVEL_SUSPEND,
 757                         .run_reg = BD718XX_REG_BUCK1_VOLT_RUN,
 758                         .run_mask = DVS_BUCK_RUN_MASK,
 759                         .idle_reg = BD718XX_REG_BUCK1_VOLT_IDLE,
 760                         .idle_mask = DVS_BUCK_RUN_MASK,
 761                         .suspend_reg = BD718XX_REG_BUCK1_VOLT_SUSP,
 762                         .suspend_mask = DVS_BUCK_RUN_MASK,
 763                 },
 764                 .init = {
 765                         .reg = BD718XX_REG_BUCK1_CTRL,
 766                         .mask = BD718XX_BUCK_SEL,
 767                         .val = BD718XX_BUCK_SEL,
 768                 },
 769         },
 770         {
 771                 .desc = {
 772                         .name = "buck2",
 773                         .of_match = of_match_ptr("BUCK2"),
 774                         .regulators_node = of_match_ptr("regulators"),
 775                         .id = BD718XX_BUCK2,
 776                         .type = REGULATOR_VOLTAGE,
 777                         .n_voltages = BD718XX_DVS_BUCK_VOLTAGE_NUM,
 778                         .linear_ranges = bd718xx_dvs_buck_volts,
 779                         .n_linear_ranges = ARRAY_SIZE(bd718xx_dvs_buck_volts),
 780                         .vsel_reg = BD718XX_REG_BUCK2_VOLT_RUN,
 781                         .vsel_mask = DVS_BUCK_RUN_MASK,
 782                         .enable_reg = BD718XX_REG_BUCK2_CTRL,
 783                         .enable_mask = BD718XX_BUCK_EN,
 784                         .enable_time = BD71847_BUCK2_STARTUP_TIME,
 785                         .ramp_delay_table = bd718xx_ramp_delay,
 786                         .n_ramp_values = ARRAY_SIZE(bd718xx_ramp_delay),
 787                         .ramp_reg = BD718XX_REG_BUCK2_CTRL,
 788                         .ramp_mask = BUCK_RAMPRATE_MASK,
 789                         .owner = THIS_MODULE,
 790                         .of_parse_cb = buck_set_hw_dvs_levels,
 791                 },
 792                 .dvs = {
 793                         .level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE,
 794                         .run_reg = BD718XX_REG_BUCK2_VOLT_RUN,
 795                         .run_mask = DVS_BUCK_RUN_MASK,
 796                         .idle_reg = BD718XX_REG_BUCK2_VOLT_IDLE,
 797                         .idle_mask = DVS_BUCK_RUN_MASK,
 798                 },
 799                 .init = {
 800                         .reg = BD718XX_REG_BUCK2_CTRL,
 801                         .mask = BD718XX_BUCK_SEL,
 802                         .val = BD718XX_BUCK_SEL,
 803                 },
 804         },
 805         {
 806                 .desc = {
 807                         .name = "buck3",
 808                         .of_match = of_match_ptr("BUCK3"),
 809                         .regulators_node = of_match_ptr("regulators"),
 810                         .id = BD718XX_BUCK3,
 811                         .type = REGULATOR_VOLTAGE,
 812                         .n_voltages = BD71847_BUCK3_VOLTAGE_NUM,
 813                         .linear_ranges = bd71847_buck3_volts,
 814                         .n_linear_ranges =
 815                                 ARRAY_SIZE(bd71847_buck3_volts),
 816                         .vsel_reg = BD718XX_REG_1ST_NODVS_BUCK_VOLT,
 817                         .vsel_mask = BD718XX_1ST_NODVS_BUCK_MASK,
 818                         .vsel_range_reg = BD718XX_REG_1ST_NODVS_BUCK_VOLT,
 819                         .vsel_range_mask = BD71847_BUCK3_RANGE_MASK,
 820                         .linear_range_selectors = bd71847_buck3_volt_range_sel,
 821                         .enable_reg = BD718XX_REG_1ST_NODVS_BUCK_CTRL,
 822                         .enable_mask = BD718XX_BUCK_EN,
 823                         .enable_time = BD71847_BUCK3_STARTUP_TIME,
 824                         .owner = THIS_MODULE,
 825                 },
 826                 .init = {
 827                         .reg = BD718XX_REG_1ST_NODVS_BUCK_CTRL,
 828                         .mask = BD718XX_BUCK_SEL,
 829                         .val = BD718XX_BUCK_SEL,
 830                 },
 831         },
 832         {
 833                 .desc = {
 834                         .name = "buck4",
 835                         .of_match = of_match_ptr("BUCK4"),
 836                         .regulators_node = of_match_ptr("regulators"),
 837                         .id = BD718XX_BUCK4,
 838                         .type = REGULATOR_VOLTAGE,
 839                         .n_voltages = BD71847_BUCK4_VOLTAGE_NUM,
 840                         .linear_ranges = bd71847_buck4_volts,
 841                         .n_linear_ranges =
 842                                 ARRAY_SIZE(bd71847_buck4_volts),
 843                         .enable_reg = BD718XX_REG_2ND_NODVS_BUCK_CTRL,
 844                         .vsel_reg = BD718XX_REG_2ND_NODVS_BUCK_VOLT,
 845                         .vsel_mask = BD71847_BUCK4_MASK,
 846                         .vsel_range_reg = BD718XX_REG_2ND_NODVS_BUCK_VOLT,
 847                         .vsel_range_mask = BD71847_BUCK4_RANGE_MASK,
 848                         .linear_range_selectors = bd71847_buck4_volt_range_sel,
 849                         .enable_mask = BD718XX_BUCK_EN,
 850                         .enable_time = BD71847_BUCK4_STARTUP_TIME,
 851                         .owner = THIS_MODULE,
 852                 },
 853                 .init = {
 854                         .reg = BD718XX_REG_2ND_NODVS_BUCK_CTRL,
 855                         .mask = BD718XX_BUCK_SEL,
 856                         .val = BD718XX_BUCK_SEL,
 857                 },
 858         },
 859         {
 860                 .desc = {
 861                         .name = "buck5",
 862                         .of_match = of_match_ptr("BUCK5"),
 863                         .regulators_node = of_match_ptr("regulators"),
 864                         .id = BD718XX_BUCK5,
 865                         .type = REGULATOR_VOLTAGE,
 866                         .volt_table = &bd718xx_3rd_nodvs_buck_volts[0],
 867                         .n_voltages = ARRAY_SIZE(bd718xx_3rd_nodvs_buck_volts),
 868                         .vsel_reg = BD718XX_REG_3RD_NODVS_BUCK_VOLT,
 869                         .vsel_mask = BD718XX_3RD_NODVS_BUCK_MASK,
 870                         .enable_reg = BD718XX_REG_3RD_NODVS_BUCK_CTRL,
 871                         .enable_mask = BD718XX_BUCK_EN,
 872                         .enable_time = BD71847_BUCK5_STARTUP_TIME,
 873                         .owner = THIS_MODULE,
 874                 },
 875                 .init = {
 876                         .reg = BD718XX_REG_3RD_NODVS_BUCK_CTRL,
 877                         .mask = BD718XX_BUCK_SEL,
 878                         .val = BD718XX_BUCK_SEL,
 879                 },
 880         },
 881         {
 882                 .desc = {
 883                         .name = "buck6",
 884                         .of_match = of_match_ptr("BUCK6"),
 885                         .regulators_node = of_match_ptr("regulators"),
 886                         .id = BD718XX_BUCK6,
 887                         .type = REGULATOR_VOLTAGE,
 888                         .n_voltages = BD718XX_4TH_NODVS_BUCK_VOLTAGE_NUM,
 889                         .linear_ranges = bd718xx_4th_nodvs_buck_volts,
 890                         .n_linear_ranges =
 891                                 ARRAY_SIZE(bd718xx_4th_nodvs_buck_volts),
 892                         .vsel_reg = BD718XX_REG_4TH_NODVS_BUCK_VOLT,
 893                         .vsel_mask = BD718XX_4TH_NODVS_BUCK_MASK,
 894                         .enable_reg = BD718XX_REG_4TH_NODVS_BUCK_CTRL,
 895                         .enable_mask = BD718XX_BUCK_EN,
 896                         .enable_time = BD71847_BUCK6_STARTUP_TIME,
 897                         .owner = THIS_MODULE,
 898                 },
 899                 .init = {
 900                         .reg = BD718XX_REG_4TH_NODVS_BUCK_CTRL,
 901                         .mask = BD718XX_BUCK_SEL,
 902                         .val = BD718XX_BUCK_SEL,
 903                 },
 904         },
 905         {
 906                 .desc = {
 907                         .name = "ldo1",
 908                         .of_match = of_match_ptr("LDO1"),
 909                         .regulators_node = of_match_ptr("regulators"),
 910                         .id = BD718XX_LDO1,
 911                         .type = REGULATOR_VOLTAGE,
 912                         .n_voltages = BD718XX_LDO1_VOLTAGE_NUM,
 913                         .linear_ranges = bd718xx_ldo1_volts,
 914                         .n_linear_ranges = ARRAY_SIZE(bd718xx_ldo1_volts),
 915                         .vsel_reg = BD718XX_REG_LDO1_VOLT,
 916                         .vsel_mask = BD718XX_LDO1_MASK,
 917                         .vsel_range_reg = BD718XX_REG_LDO1_VOLT,
 918                         .vsel_range_mask = BD718XX_LDO1_RANGE_MASK,
 919                         .linear_range_selectors = bd718xx_ldo1_volt_range_sel,
 920                         .enable_reg = BD718XX_REG_LDO1_VOLT,
 921                         .enable_mask = BD718XX_LDO_EN,
 922                         .enable_time = BD71847_LDO1_STARTUP_TIME,
 923                         .owner = THIS_MODULE,
 924                 },
 925                 .init = {
 926                         .reg = BD718XX_REG_LDO1_VOLT,
 927                         .mask = BD718XX_LDO_SEL,
 928                         .val = BD718XX_LDO_SEL,
 929                 },
 930         },
 931         {
 932                 .desc = {
 933                         .name = "ldo2",
 934                         .of_match = of_match_ptr("LDO2"),
 935                         .regulators_node = of_match_ptr("regulators"),
 936                         .id = BD718XX_LDO2,
 937                         .type = REGULATOR_VOLTAGE,
 938                         .volt_table = &ldo_2_volts[0],
 939                         .vsel_reg = BD718XX_REG_LDO2_VOLT,
 940                         .vsel_mask = BD718XX_LDO2_MASK,
 941                         .n_voltages = ARRAY_SIZE(ldo_2_volts),
 942                         .enable_reg = BD718XX_REG_LDO2_VOLT,
 943                         .enable_mask = BD718XX_LDO_EN,
 944                         .enable_time = BD71847_LDO2_STARTUP_TIME,
 945                         .owner = THIS_MODULE,
 946                 },
 947                 .init = {
 948                         .reg = BD718XX_REG_LDO2_VOLT,
 949                         .mask = BD718XX_LDO_SEL,
 950                         .val = BD718XX_LDO_SEL,
 951                 },
 952         },
 953         {
 954                 .desc = {
 955                         .name = "ldo3",
 956                         .of_match = of_match_ptr("LDO3"),
 957                         .regulators_node = of_match_ptr("regulators"),
 958                         .id = BD718XX_LDO3,
 959                         .type = REGULATOR_VOLTAGE,
 960                         .n_voltages = BD718XX_LDO3_VOLTAGE_NUM,
 961                         .linear_ranges = bd718xx_ldo3_volts,
 962                         .n_linear_ranges = ARRAY_SIZE(bd718xx_ldo3_volts),
 963                         .vsel_reg = BD718XX_REG_LDO3_VOLT,
 964                         .vsel_mask = BD718XX_LDO3_MASK,
 965                         .enable_reg = BD718XX_REG_LDO3_VOLT,
 966                         .enable_mask = BD718XX_LDO_EN,
 967                         .enable_time = BD71847_LDO3_STARTUP_TIME,
 968                         .owner = THIS_MODULE,
 969                 },
 970                 .init = {
 971                         .reg = BD718XX_REG_LDO3_VOLT,
 972                         .mask = BD718XX_LDO_SEL,
 973                         .val = BD718XX_LDO_SEL,
 974                 },
 975         },
 976         {
 977                 .desc = {
 978                         .name = "ldo4",
 979                         .of_match = of_match_ptr("LDO4"),
 980                         .regulators_node = of_match_ptr("regulators"),
 981                         .id = BD718XX_LDO4,
 982                         .type = REGULATOR_VOLTAGE,
 983                         .n_voltages = BD718XX_LDO4_VOLTAGE_NUM,
 984                         .linear_ranges = bd718xx_ldo4_volts,
 985                         .n_linear_ranges = ARRAY_SIZE(bd718xx_ldo4_volts),
 986                         .vsel_reg = BD718XX_REG_LDO4_VOLT,
 987                         .vsel_mask = BD718XX_LDO4_MASK,
 988                         .enable_reg = BD718XX_REG_LDO4_VOLT,
 989                         .enable_mask = BD718XX_LDO_EN,
 990                         .enable_time = BD71847_LDO4_STARTUP_TIME,
 991                         .owner = THIS_MODULE,
 992                 },
 993                 .init = {
 994                         .reg = BD718XX_REG_LDO4_VOLT,
 995                         .mask = BD718XX_LDO_SEL,
 996                         .val = BD718XX_LDO_SEL,
 997                 },
 998         },
 999         {
1000                 .desc = {
1001                         .name = "ldo5",
1002                         .of_match = of_match_ptr("LDO5"),
1003                         .regulators_node = of_match_ptr("regulators"),
1004                         .id = BD718XX_LDO5,
1005                         .type = REGULATOR_VOLTAGE,
1006                         .n_voltages = BD71847_LDO5_VOLTAGE_NUM,
1007                         .linear_ranges = bd71847_ldo5_volts,
1008                         .n_linear_ranges = ARRAY_SIZE(bd71847_ldo5_volts),
1009                         .vsel_reg = BD718XX_REG_LDO5_VOLT,
1010                         .vsel_mask = BD71847_LDO5_MASK,
1011                         .vsel_range_reg = BD718XX_REG_LDO5_VOLT,
1012                         .vsel_range_mask = BD71847_LDO5_RANGE_MASK,
1013                         .linear_range_selectors = bd71847_ldo5_volt_range_sel,
1014                         .enable_reg = BD718XX_REG_LDO5_VOLT,
1015                         .enable_mask = BD718XX_LDO_EN,
1016                         .enable_time = BD71847_LDO5_STARTUP_TIME,
1017                         .owner = THIS_MODULE,
1018                 },
1019                 .init = {
1020                         .reg = BD718XX_REG_LDO5_VOLT,
1021                         .mask = BD718XX_LDO_SEL,
1022                         .val = BD718XX_LDO_SEL,
1023                 },
1024         },
1025         {
1026                 .desc = {
1027                         .name = "ldo6",
1028                         .of_match = of_match_ptr("LDO6"),
1029                         .regulators_node = of_match_ptr("regulators"),
1030                         .id = BD718XX_LDO6,
1031                         .type = REGULATOR_VOLTAGE,
1032                         .n_voltages = BD718XX_LDO6_VOLTAGE_NUM,
1033                         .linear_ranges = bd718xx_ldo6_volts,
1034                         .n_linear_ranges = ARRAY_SIZE(bd718xx_ldo6_volts),
1035                         /* LDO6 is supplied by buck5 */
1036                         .supply_name = "buck5",
1037                         .vsel_reg = BD718XX_REG_LDO6_VOLT,
1038                         .vsel_mask = BD718XX_LDO6_MASK,
1039                         .enable_reg = BD718XX_REG_LDO6_VOLT,
1040                         .enable_mask = BD718XX_LDO_EN,
1041                         .enable_time = BD71847_LDO6_STARTUP_TIME,
1042                         .owner = THIS_MODULE,
1043                 },
1044                 .init = {
1045                         .reg = BD718XX_REG_LDO6_VOLT,
1046                         .mask = BD718XX_LDO_SEL,
1047                         .val = BD718XX_LDO_SEL,
1048                 },
1049         },
1050 };
1051
1052 static const struct regulator_ops *bd71837_swcontrol_ops[] = {
1053         &bd718xx_dvs_buck_regulator_ops, &bd718xx_dvs_buck_regulator_ops,
1054         &bd718xx_dvs_buck_regulator_ops, &bd718xx_dvs_buck_regulator_ops,
1055         &bd71837_pickable_range_buck_ops, &bd71837_buck_regulator_ops,
1056         &bd71837_buck_regulator_nolinear_ops, &bd71837_buck_regulator_ops,
1057         &bd71837_pickable_range_ldo_ops, &bd71837_ldo_regulator_nolinear_ops,
1058         &bd71837_ldo_regulator_ops, &bd71837_ldo_regulator_ops,
1059         &bd71837_ldo_regulator_ops, &bd71837_ldo_regulator_ops,
1060         &bd71837_ldo_regulator_ops,
1061 };
1062
1063 static const struct regulator_ops *bd71837_hwcontrol_ops[] = {
1064         &BD718XX_HWOPNAME(bd718xx_dvs_buck_regulator_ops),
1065         &BD718XX_HWOPNAME(bd718xx_dvs_buck_regulator_ops),
1066         &bd71837_buck34_ops_hwctrl, &bd71837_buck34_ops_hwctrl,
1067         &BD718XX_HWOPNAME(bd71837_pickable_range_buck_ops),
1068         &BD718XX_HWOPNAME(bd71837_buck_regulator_ops),
1069         &BD718XX_HWOPNAME(bd71837_buck_regulator_nolinear_ops),
1070         &BD718XX_HWOPNAME(bd71837_buck_regulator_ops),
1071         &BD718XX_HWOPNAME(bd71837_pickable_range_ldo_ops),
1072         &BD718XX_HWOPNAME(bd71837_ldo_regulator_nolinear_ops),
1073         &BD718XX_HWOPNAME(bd71837_ldo_regulator_ops),
1074         &BD718XX_HWOPNAME(bd71837_ldo_regulator_ops),
1075         &BD718XX_HWOPNAME(bd71837_ldo_regulator_ops),
1076         &BD718XX_HWOPNAME(bd71837_ldo_regulator_ops),
1077         &BD718XX_HWOPNAME(bd71837_ldo_regulator_ops),
1078 };
1079
1080 static struct bd718xx_regulator_data bd71837_regulators[] = {
1081         {
1082                 .desc = {
1083                         .name = "buck1",
1084                         .of_match = of_match_ptr("BUCK1"),
1085                         .regulators_node = of_match_ptr("regulators"),
1086                         .id = BD718XX_BUCK1,
1087                         .type = REGULATOR_VOLTAGE,
1088                         .n_voltages = BD718XX_DVS_BUCK_VOLTAGE_NUM,
1089                         .linear_ranges = bd718xx_dvs_buck_volts,
1090                         .n_linear_ranges = ARRAY_SIZE(bd718xx_dvs_buck_volts),
1091                         .vsel_reg = BD718XX_REG_BUCK1_VOLT_RUN,
1092                         .vsel_mask = DVS_BUCK_RUN_MASK,
1093                         .enable_reg = BD718XX_REG_BUCK1_CTRL,
1094                         .enable_mask = BD718XX_BUCK_EN,
1095                         .enable_time = BD71837_BUCK1_STARTUP_TIME,
1096                         .ramp_delay_table = bd718xx_ramp_delay,
1097                         .n_ramp_values = ARRAY_SIZE(bd718xx_ramp_delay),
1098                         .ramp_reg = BD718XX_REG_BUCK1_CTRL,
1099                         .ramp_mask = BUCK_RAMPRATE_MASK,
1100                         .owner = THIS_MODULE,
1101                         .of_parse_cb = buck_set_hw_dvs_levels,
1102                 },
1103                 .dvs = {
1104                         .level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE |
1105                                      ROHM_DVS_LEVEL_SUSPEND,
1106                         .run_reg = BD718XX_REG_BUCK1_VOLT_RUN,
1107                         .run_mask = DVS_BUCK_RUN_MASK,
1108                         .idle_reg = BD718XX_REG_BUCK1_VOLT_IDLE,
1109                         .idle_mask = DVS_BUCK_RUN_MASK,
1110                         .suspend_reg = BD718XX_REG_BUCK1_VOLT_SUSP,
1111                         .suspend_mask = DVS_BUCK_RUN_MASK,
1112                 },
1113                 .init = {
1114                         .reg = BD718XX_REG_BUCK1_CTRL,
1115                         .mask = BD718XX_BUCK_SEL,
1116                         .val = BD718XX_BUCK_SEL,
1117                 },
1118         },
1119         {
1120                 .desc = {
1121                         .name = "buck2",
1122                         .of_match = of_match_ptr("BUCK2"),
1123                         .regulators_node = of_match_ptr("regulators"),
1124                         .id = BD718XX_BUCK2,
1125                         .type = REGULATOR_VOLTAGE,
1126                         .n_voltages = BD718XX_DVS_BUCK_VOLTAGE_NUM,
1127                         .linear_ranges = bd718xx_dvs_buck_volts,
1128                         .n_linear_ranges = ARRAY_SIZE(bd718xx_dvs_buck_volts),
1129                         .vsel_reg = BD718XX_REG_BUCK2_VOLT_RUN,
1130                         .vsel_mask = DVS_BUCK_RUN_MASK,
1131                         .enable_reg = BD718XX_REG_BUCK2_CTRL,
1132                         .enable_mask = BD718XX_BUCK_EN,
1133                         .enable_time = BD71837_BUCK2_STARTUP_TIME,
1134                         .ramp_delay_table = bd718xx_ramp_delay,
1135                         .n_ramp_values = ARRAY_SIZE(bd718xx_ramp_delay),
1136                         .ramp_reg = BD718XX_REG_BUCK2_CTRL,
1137                         .ramp_mask = BUCK_RAMPRATE_MASK,
1138                         .owner = THIS_MODULE,
1139                         .of_parse_cb = buck_set_hw_dvs_levels,
1140                 },
1141                 .dvs = {
1142                         .level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE,
1143                         .run_reg = BD718XX_REG_BUCK2_VOLT_RUN,
1144                         .run_mask = DVS_BUCK_RUN_MASK,
1145                         .idle_reg = BD718XX_REG_BUCK2_VOLT_IDLE,
1146                         .idle_mask = DVS_BUCK_RUN_MASK,
1147                 },
1148                 .init = {
1149                         .reg = BD718XX_REG_BUCK2_CTRL,
1150                         .mask = BD718XX_BUCK_SEL,
1151                         .val = BD718XX_BUCK_SEL,
1152                 },
1153         },
1154         {
1155                 .desc = {
1156                         .name = "buck3",
1157                         .of_match = of_match_ptr("BUCK3"),
1158                         .regulators_node = of_match_ptr("regulators"),
1159                         .id = BD718XX_BUCK3,
1160                         .type = REGULATOR_VOLTAGE,
1161                         .n_voltages = BD718XX_DVS_BUCK_VOLTAGE_NUM,
1162                         .linear_ranges = bd718xx_dvs_buck_volts,
1163                         .n_linear_ranges = ARRAY_SIZE(bd718xx_dvs_buck_volts),
1164                         .vsel_reg = BD71837_REG_BUCK3_VOLT_RUN,
1165                         .vsel_mask = DVS_BUCK_RUN_MASK,
1166                         .enable_reg = BD71837_REG_BUCK3_CTRL,
1167                         .enable_mask = BD718XX_BUCK_EN,
1168                         .enable_time = BD71837_BUCK3_STARTUP_TIME,
1169                         .ramp_delay_table = bd718xx_ramp_delay,
1170                         .n_ramp_values = ARRAY_SIZE(bd718xx_ramp_delay),
1171                         .ramp_reg = BD71837_REG_BUCK3_CTRL,
1172                         .ramp_mask = BUCK_RAMPRATE_MASK,
1173                         .owner = THIS_MODULE,
1174                         .of_parse_cb = buck_set_hw_dvs_levels,
1175                 },
1176                 .dvs = {
1177                         .level_map = ROHM_DVS_LEVEL_RUN,
1178                         .run_reg = BD71837_REG_BUCK3_VOLT_RUN,
1179                         .run_mask = DVS_BUCK_RUN_MASK,
1180                 },
1181                 .init = {
1182                         .reg = BD71837_REG_BUCK3_CTRL,
1183                         .mask = BD718XX_BUCK_SEL,
1184                         .val = BD718XX_BUCK_SEL,
1185                 },
1186         },
1187         {
1188                 .desc = {
1189                         .name = "buck4",
1190                         .of_match = of_match_ptr("BUCK4"),
1191                         .regulators_node = of_match_ptr("regulators"),
1192                         .id = BD718XX_BUCK4,
1193                         .type = REGULATOR_VOLTAGE,
1194                         .n_voltages = BD718XX_DVS_BUCK_VOLTAGE_NUM,
1195                         .linear_ranges = bd718xx_dvs_buck_volts,
1196                         .n_linear_ranges = ARRAY_SIZE(bd718xx_dvs_buck_volts),
1197                         .vsel_reg = BD71837_REG_BUCK4_VOLT_RUN,
1198                         .vsel_mask = DVS_BUCK_RUN_MASK,
1199                         .enable_reg = BD71837_REG_BUCK4_CTRL,
1200                         .enable_mask = BD718XX_BUCK_EN,
1201                         .enable_time = BD71837_BUCK4_STARTUP_TIME,
1202                         .ramp_delay_table = bd718xx_ramp_delay,
1203                         .n_ramp_values = ARRAY_SIZE(bd718xx_ramp_delay),
1204                         .ramp_reg = BD71837_REG_BUCK4_CTRL,
1205                         .ramp_mask = BUCK_RAMPRATE_MASK,
1206                         .owner = THIS_MODULE,
1207                         .of_parse_cb = buck_set_hw_dvs_levels,
1208                 },
1209                 .dvs = {
1210                         .level_map = ROHM_DVS_LEVEL_RUN,
1211                         .run_reg = BD71837_REG_BUCK4_VOLT_RUN,
1212                         .run_mask = DVS_BUCK_RUN_MASK,
1213                 },
1214                 .init = {
1215                         .reg = BD71837_REG_BUCK4_CTRL,
1216                         .mask = BD718XX_BUCK_SEL,
1217                         .val = BD718XX_BUCK_SEL,
1218                 },
1219         },
1220         {
1221                 .desc = {
1222                         .name = "buck5",
1223                         .of_match = of_match_ptr("BUCK5"),
1224                         .regulators_node = of_match_ptr("regulators"),
1225                         .id = BD718XX_BUCK5,
1226                         .type = REGULATOR_VOLTAGE,
1227                         .n_voltages = BD71837_BUCK5_VOLTAGE_NUM,
1228                         .linear_ranges = bd71837_buck5_volts,
1229                         .n_linear_ranges =
1230                                 ARRAY_SIZE(bd71837_buck5_volts),
1231                         .vsel_reg = BD718XX_REG_1ST_NODVS_BUCK_VOLT,
1232                         .vsel_mask = BD71837_BUCK5_MASK,
1233                         .vsel_range_reg = BD718XX_REG_1ST_NODVS_BUCK_VOLT,
1234                         .vsel_range_mask = BD71837_BUCK5_RANGE_MASK,
1235                         .linear_range_selectors = bd71837_buck5_volt_range_sel,
1236                         .enable_reg = BD718XX_REG_1ST_NODVS_BUCK_CTRL,
1237                         .enable_mask = BD718XX_BUCK_EN,
1238                         .enable_time = BD71837_BUCK5_STARTUP_TIME,
1239                         .owner = THIS_MODULE,
1240                 },
1241                 .init = {
1242                         .reg = BD718XX_REG_1ST_NODVS_BUCK_CTRL,
1243                         .mask = BD718XX_BUCK_SEL,
1244                         .val = BD718XX_BUCK_SEL,
1245                 },
1246         },
1247         {
1248                 .desc = {
1249                         .name = "buck6",
1250                         .of_match = of_match_ptr("BUCK6"),
1251                         .regulators_node = of_match_ptr("regulators"),
1252                         .id = BD718XX_BUCK6,
1253                         .type = REGULATOR_VOLTAGE,
1254                         .n_voltages = BD71837_BUCK6_VOLTAGE_NUM,
1255                         .linear_ranges = bd71837_buck6_volts,
1256                         .n_linear_ranges =
1257                                 ARRAY_SIZE(bd71837_buck6_volts),
1258                         .vsel_reg = BD718XX_REG_2ND_NODVS_BUCK_VOLT,
1259                         .vsel_mask = BD71837_BUCK6_MASK,
1260                         .enable_reg = BD718XX_REG_2ND_NODVS_BUCK_CTRL,
1261                         .enable_mask = BD718XX_BUCK_EN,
1262                         .enable_time = BD71837_BUCK6_STARTUP_TIME,
1263                         .owner = THIS_MODULE,
1264                 },
1265                 .init = {
1266                         .reg = BD718XX_REG_2ND_NODVS_BUCK_CTRL,
1267                         .mask = BD718XX_BUCK_SEL,
1268                         .val = BD718XX_BUCK_SEL,
1269                 },
1270         },
1271         {
1272                 .desc = {
1273                         .name = "buck7",
1274                         .of_match = of_match_ptr("BUCK7"),
1275                         .regulators_node = of_match_ptr("regulators"),
1276                         .id = BD718XX_BUCK7,
1277                         .type = REGULATOR_VOLTAGE,
1278                         .volt_table = &bd718xx_3rd_nodvs_buck_volts[0],
1279                         .n_voltages = ARRAY_SIZE(bd718xx_3rd_nodvs_buck_volts),
1280                         .vsel_reg = BD718XX_REG_3RD_NODVS_BUCK_VOLT,
1281                         .vsel_mask = BD718XX_3RD_NODVS_BUCK_MASK,
1282                         .enable_reg = BD718XX_REG_3RD_NODVS_BUCK_CTRL,
1283                         .enable_mask = BD718XX_BUCK_EN,
1284                         .enable_time = BD71837_BUCK7_STARTUP_TIME,
1285                         .owner = THIS_MODULE,
1286                 },
1287                 .init = {
1288                         .reg = BD718XX_REG_3RD_NODVS_BUCK_CTRL,
1289                         .mask = BD718XX_BUCK_SEL,
1290                         .val = BD718XX_BUCK_SEL,
1291                 },
1292         },
1293         {
1294                 .desc = {
1295                         .name = "buck8",
1296                         .of_match = of_match_ptr("BUCK8"),
1297                         .regulators_node = of_match_ptr("regulators"),
1298                         .id = BD718XX_BUCK8,
1299                         .type = REGULATOR_VOLTAGE,
1300                         .n_voltages = BD718XX_4TH_NODVS_BUCK_VOLTAGE_NUM,
1301                         .linear_ranges = bd718xx_4th_nodvs_buck_volts,
1302                         .n_linear_ranges =
1303                                 ARRAY_SIZE(bd718xx_4th_nodvs_buck_volts),
1304                         .vsel_reg = BD718XX_REG_4TH_NODVS_BUCK_VOLT,
1305                         .vsel_mask = BD718XX_4TH_NODVS_BUCK_MASK,
1306                         .enable_reg = BD718XX_REG_4TH_NODVS_BUCK_CTRL,
1307                         .enable_mask = BD718XX_BUCK_EN,
1308                         .enable_time = BD71837_BUCK8_STARTUP_TIME,
1309                         .owner = THIS_MODULE,
1310                 },
1311                 .init = {
1312                         .reg = BD718XX_REG_4TH_NODVS_BUCK_CTRL,
1313                         .mask = BD718XX_BUCK_SEL,
1314                         .val = BD718XX_BUCK_SEL,
1315                 },
1316         },
1317         {
1318                 .desc = {
1319                         .name = "ldo1",
1320                         .of_match = of_match_ptr("LDO1"),
1321                         .regulators_node = of_match_ptr("regulators"),
1322                         .id = BD718XX_LDO1,
1323                         .type = REGULATOR_VOLTAGE,
1324                         .n_voltages = BD718XX_LDO1_VOLTAGE_NUM,
1325                         .linear_ranges = bd718xx_ldo1_volts,
1326                         .n_linear_ranges = ARRAY_SIZE(bd718xx_ldo1_volts),
1327                         .vsel_reg = BD718XX_REG_LDO1_VOLT,
1328                         .vsel_mask = BD718XX_LDO1_MASK,
1329                         .vsel_range_reg = BD718XX_REG_LDO1_VOLT,
1330                         .vsel_range_mask = BD718XX_LDO1_RANGE_MASK,
1331                         .linear_range_selectors = bd718xx_ldo1_volt_range_sel,
1332                         .enable_reg = BD718XX_REG_LDO1_VOLT,
1333                         .enable_mask = BD718XX_LDO_EN,
1334                         .enable_time = BD71837_LDO1_STARTUP_TIME,
1335                         .owner = THIS_MODULE,
1336                 },
1337                 .init = {
1338                         .reg = BD718XX_REG_LDO1_VOLT,
1339                         .mask = BD718XX_LDO_SEL,
1340                         .val = BD718XX_LDO_SEL,
1341                 },
1342         },
1343         {
1344                 .desc = {
1345                         .name = "ldo2",
1346                         .of_match = of_match_ptr("LDO2"),
1347                         .regulators_node = of_match_ptr("regulators"),
1348                         .id = BD718XX_LDO2,
1349                         .type = REGULATOR_VOLTAGE,
1350                         .volt_table = &ldo_2_volts[0],
1351                         .vsel_reg = BD718XX_REG_LDO2_VOLT,
1352                         .vsel_mask = BD718XX_LDO2_MASK,
1353                         .n_voltages = ARRAY_SIZE(ldo_2_volts),
1354                         .enable_reg = BD718XX_REG_LDO2_VOLT,
1355                         .enable_mask = BD718XX_LDO_EN,
1356                         .enable_time = BD71837_LDO2_STARTUP_TIME,
1357                         .owner = THIS_MODULE,
1358                 },
1359                 .init = {
1360                         .reg = BD718XX_REG_LDO2_VOLT,
1361                         .mask = BD718XX_LDO_SEL,
1362                         .val = BD718XX_LDO_SEL,
1363                 },
1364         },
1365         {
1366                 .desc = {
1367                         .name = "ldo3",
1368                         .of_match = of_match_ptr("LDO3"),
1369                         .regulators_node = of_match_ptr("regulators"),
1370                         .id = BD718XX_LDO3,
1371                         .type = REGULATOR_VOLTAGE,
1372                         .n_voltages = BD718XX_LDO3_VOLTAGE_NUM,
1373                         .linear_ranges = bd718xx_ldo3_volts,
1374                         .n_linear_ranges = ARRAY_SIZE(bd718xx_ldo3_volts),
1375                         .vsel_reg = BD718XX_REG_LDO3_VOLT,
1376                         .vsel_mask = BD718XX_LDO3_MASK,
1377                         .enable_reg = BD718XX_REG_LDO3_VOLT,
1378                         .enable_mask = BD718XX_LDO_EN,
1379                         .enable_time = BD71837_LDO3_STARTUP_TIME,
1380                         .owner = THIS_MODULE,
1381                 },
1382                 .init = {
1383                         .reg = BD718XX_REG_LDO3_VOLT,
1384                         .mask = BD718XX_LDO_SEL,
1385                         .val = BD718XX_LDO_SEL,
1386                 },
1387         },
1388         {
1389                 .desc = {
1390                         .name = "ldo4",
1391                         .of_match = of_match_ptr("LDO4"),
1392                         .regulators_node = of_match_ptr("regulators"),
1393                         .id = BD718XX_LDO4,
1394                         .type = REGULATOR_VOLTAGE,
1395                         .n_voltages = BD718XX_LDO4_VOLTAGE_NUM,
1396                         .linear_ranges = bd718xx_ldo4_volts,
1397                         .n_linear_ranges = ARRAY_SIZE(bd718xx_ldo4_volts),
1398                         .vsel_reg = BD718XX_REG_LDO4_VOLT,
1399                         .vsel_mask = BD718XX_LDO4_MASK,
1400                         .enable_reg = BD718XX_REG_LDO4_VOLT,
1401                         .enable_mask = BD718XX_LDO_EN,
1402                         .enable_time = BD71837_LDO4_STARTUP_TIME,
1403                         .owner = THIS_MODULE,
1404                 },
1405                 .init = {
1406                         .reg = BD718XX_REG_LDO4_VOLT,
1407                         .mask = BD718XX_LDO_SEL,
1408                         .val = BD718XX_LDO_SEL,
1409                 },
1410         },
1411         {
1412                 .desc = {
1413                         .name = "ldo5",
1414                         .of_match = of_match_ptr("LDO5"),
1415                         .regulators_node = of_match_ptr("regulators"),
1416                         .id = BD718XX_LDO5,
1417                         .type = REGULATOR_VOLTAGE,
1418                         .n_voltages = BD71837_LDO5_VOLTAGE_NUM,
1419                         .linear_ranges = bd71837_ldo5_volts,
1420                         .n_linear_ranges = ARRAY_SIZE(bd71837_ldo5_volts),
1421                         /* LDO5 is supplied by buck6 */
1422                         .supply_name = "buck6",
1423                         .vsel_reg = BD718XX_REG_LDO5_VOLT,
1424                         .vsel_mask = BD71837_LDO5_MASK,
1425                         .enable_reg = BD718XX_REG_LDO5_VOLT,
1426                         .enable_mask = BD718XX_LDO_EN,
1427                         .enable_time = BD71837_LDO5_STARTUP_TIME,
1428                         .owner = THIS_MODULE,
1429                 },
1430                 .init = {
1431                         .reg = BD718XX_REG_LDO5_VOLT,
1432                         .mask = BD718XX_LDO_SEL,
1433                         .val = BD718XX_LDO_SEL,
1434                 },
1435                 .additional_inits = bd71837_ldo5_inits,
1436                 .additional_init_amnt = ARRAY_SIZE(bd71837_ldo5_inits),
1437         },
1438         {
1439                 .desc = {
1440                         .name = "ldo6",
1441                         .of_match = of_match_ptr("LDO6"),
1442                         .regulators_node = of_match_ptr("regulators"),
1443                         .id = BD718XX_LDO6,
1444                         .type = REGULATOR_VOLTAGE,
1445                         .n_voltages = BD718XX_LDO6_VOLTAGE_NUM,
1446                         .linear_ranges = bd718xx_ldo6_volts,
1447                         .n_linear_ranges = ARRAY_SIZE(bd718xx_ldo6_volts),
1448                         /* LDO6 is supplied by buck7 */
1449                         .supply_name = "buck7",
1450                         .vsel_reg = BD718XX_REG_LDO6_VOLT,
1451                         .vsel_mask = BD718XX_LDO6_MASK,
1452                         .enable_reg = BD718XX_REG_LDO6_VOLT,
1453                         .enable_mask = BD718XX_LDO_EN,
1454                         .enable_time = BD71837_LDO6_STARTUP_TIME,
1455                         .owner = THIS_MODULE,
1456                 },
1457                 .init = {
1458                         .reg = BD718XX_REG_LDO6_VOLT,
1459                         .mask = BD718XX_LDO_SEL,
1460                         .val = BD718XX_LDO_SEL,
1461                 },
1462                 .additional_inits = bd71837_ldo6_inits,
1463                 .additional_init_amnt = ARRAY_SIZE(bd71837_ldo6_inits),
1464         },
1465         {
1466                 .desc = {
1467                         .name = "ldo7",
1468                         .of_match = of_match_ptr("LDO7"),
1469                         .regulators_node = of_match_ptr("regulators"),
1470                         .id = BD718XX_LDO7,
1471                         .type = REGULATOR_VOLTAGE,
1472                         .n_voltages = BD71837_LDO7_VOLTAGE_NUM,
1473                         .linear_ranges = bd71837_ldo7_volts,
1474                         .n_linear_ranges = ARRAY_SIZE(bd71837_ldo7_volts),
1475                         .vsel_reg = BD71837_REG_LDO7_VOLT,
1476                         .vsel_mask = BD71837_LDO7_MASK,
1477                         .enable_reg = BD71837_REG_LDO7_VOLT,
1478                         .enable_mask = BD718XX_LDO_EN,
1479                         .enable_time = BD71837_LDO7_STARTUP_TIME,
1480                         .owner = THIS_MODULE,
1481                 },
1482                 .init = {
1483                         .reg = BD71837_REG_LDO7_VOLT,
1484                         .mask = BD718XX_LDO_SEL,
1485                         .val = BD718XX_LDO_SEL,
1486                 },
1487         },
1488 };
1489
1490 static void mark_hw_controlled(struct device *dev, struct device_node *np,
1491                                struct bd718xx_regulator_data *reg_data,
1492                                unsigned int num_reg_data, int *info)
1493 {
1494         int i;
1495
1496         for (i = 1; i <= num_reg_data; i++) {
1497                 if (!of_node_name_eq(np, reg_data[i-1].desc.of_match))
1498                         continue;
1499
1500                 *info |= 1 << (i - 1);
1501                 dev_dbg(dev, "regulator %d runlevel controlled\n", i);
1502                 return;
1503         }
1504         dev_warn(dev, "Bad regulator node\n");
1505 }
1506
1507 /*
1508  * Setups where regulator (especially the buck8) output voltage is scaled
1509  * by adding external connection where some other regulator output is connected
1510  * to feedback-pin (over suitable resistors) is getting popular amongst users
1511  * of BD71837. (This allows for example scaling down the buck8 voltages to suit
1512  * lover GPU voltages for projects where buck8 is (ab)used to supply power
1513  * for GPU. Additionally some setups do allow DVS for buck8 but as this do
1514  * produce voltage spikes the HW must be evaluated to be able to survive this
1515  * - hence I keep the DVS disabled for non DVS bucks by default. I don't want
1516  * to help you burn your proto board)
1517  *
1518  * So we allow describing this external connection from DT and scale the
1519  * voltages accordingly. This is what the connection should look like:
1520  *
1521  * |------------|
1522  * |    buck 8  |-------+----->Vout
1523  * |            |       |
1524  * |------------|       |
1525  *      | FB pin        |
1526  *      |               |
1527  *      +-------+--R2---+
1528  *              |
1529  *              R1
1530  *              |
1531  *      V FB-pull-up
1532  *
1533  *      Here the buck output is sifted according to formula:
1534  *
1535  * Vout_o = Vo - (Vpu - Vo)*R2/R1
1536  * Linear_step = step_orig*(R1+R2)/R1
1537  *
1538  * where:
1539  * Vout_o is adjusted voltage output at vsel reg value 0
1540  * Vo is original voltage output at vsel reg value 0
1541  * Vpu is the pull-up voltage V FB-pull-up in the picture
1542  * R1 and R2 are resistor values.
1543  *
1544  * As a real world example for buck8 and a specific GPU:
1545  * VLDO = 1.6V (used as FB-pull-up)
1546  * R1 = 1000ohms
1547  * R2 = 150ohms
1548  * VSEL 0x0 => 0.8V – (VLDO – 0.8) * R2 / R1 = 0.68V
1549  * Linear Step = 10mV * (R1 + R2) / R1 = 11.5mV
1550  */
1551 static int setup_feedback_loop(struct device *dev, struct device_node *np,
1552                                struct bd718xx_regulator_data *reg_data,
1553                                unsigned int num_reg_data, int fb_uv)
1554 {
1555         int i, r1, r2, ret;
1556
1557         /*
1558          * We do adjust the values in the global desc based on DT settings.
1559          * This may not be best approach as it can cause problems if more than
1560          * one PMIC is controlled from same processor. I don't see such use-case
1561          * for BD718x7 now - so we spare some bits.
1562          *
1563          * If this will point out to be a problem - then we can allocate new
1564          * bd718xx_regulator_data array at probe and just use the global
1565          * array as a template where we copy initial values. Then we can
1566          * use allocated descs for regultor registration and do IC specific
1567          * modifications to this copy while leaving other PMICs untouched. But
1568          * that means allocating new array for each PMIC - and currently I see
1569          * no need for that.
1570          */
1571
1572         for (i = 0; i < num_reg_data; i++) {
1573                 struct regulator_desc *desc = &reg_data[i].desc;
1574                 int j;
1575
1576                 if (!of_node_name_eq(np, desc->of_match))
1577                         continue;
1578
1579                 /* The feedback loop connection does not make sense for LDOs */
1580                 if (desc->id >= BD718XX_LDO1)
1581                         return -EINVAL;
1582
1583                 ret = of_property_read_u32(np, "rohm,feedback-pull-up-r1-ohms",
1584                                            &r1);
1585                 if (ret)
1586                         return ret;
1587
1588                 if (!r1)
1589                         return -EINVAL;
1590
1591                 ret = of_property_read_u32(np, "rohm,feedback-pull-up-r2-ohms",
1592                                            &r2);
1593                 if (ret)
1594                         return ret;
1595
1596                 if (desc->n_linear_ranges && desc->linear_ranges) {
1597                         struct linear_range *new;
1598
1599                         new = devm_kzalloc(dev, desc->n_linear_ranges *
1600                                            sizeof(struct linear_range),
1601                                            GFP_KERNEL);
1602                         if (!new)
1603                                 return -ENOMEM;
1604
1605                         for (j = 0; j < desc->n_linear_ranges; j++) {
1606                                 int min = desc->linear_ranges[j].min;
1607                                 int step = desc->linear_ranges[j].step;
1608
1609                                 min -= (fb_uv - min)*r2/r1;
1610                                 step = step * (r1 + r2);
1611                                 step /= r1;
1612
1613                                 new[j].min = min;
1614                                 new[j].step = step;
1615
1616                                 dev_dbg(dev, "%s: old range min %d, step %d\n",
1617                                         desc->name, desc->linear_ranges[j].min,
1618                                         desc->linear_ranges[j].step);
1619                                 dev_dbg(dev, "new range min %d, step %d\n", min,
1620                                         step);
1621                         }
1622                         desc->linear_ranges = new;
1623                 }
1624                 dev_dbg(dev, "regulator '%s' has FB pull-up configured\n",
1625                         desc->name);
1626
1627                 return 0;
1628         }
1629
1630         return -ENODEV;
1631 }
1632
1633 static int get_special_regulators(struct device *dev,
1634                                   struct bd718xx_regulator_data *reg_data,
1635                                   unsigned int num_reg_data, int *info)
1636 {
1637         int ret;
1638         struct device_node *np;
1639         struct device_node *nproot = dev->of_node;
1640         int uv;
1641
1642         *info = 0;
1643
1644         nproot = of_get_child_by_name(nproot, "regulators");
1645         if (!nproot) {
1646                 dev_err(dev, "failed to find regulators node\n");
1647                 return -ENODEV;
1648         }
1649         for_each_child_of_node(nproot, np) {
1650                 if (of_property_read_bool(np, "rohm,no-regulator-enable-control"))
1651                         mark_hw_controlled(dev, np, reg_data, num_reg_data,
1652                                            info);
1653                 ret = of_property_read_u32(np, "rohm,fb-pull-up-microvolt",
1654                                            &uv);
1655                 if (ret) {
1656                         if (ret == -EINVAL)
1657                                 continue;
1658                         else
1659                                 goto err_out;
1660                 }
1661
1662                 ret = setup_feedback_loop(dev, np, reg_data, num_reg_data, uv);
1663                 if (ret)
1664                         goto err_out;
1665         }
1666
1667         of_node_put(nproot);
1668         return 0;
1669
1670 err_out:
1671         of_node_put(np);
1672         of_node_put(nproot);
1673
1674         return ret;
1675 }
1676
1677 static int bd718xx_probe(struct platform_device *pdev)
1678 {
1679         struct regmap *regmap;
1680         struct regulator_config config = { 0 };
1681         int i, j, err, omit_enable;
1682         bool use_snvs;
1683         struct bd718xx_regulator_data *reg_data;
1684         unsigned int num_reg_data;
1685         enum rohm_chip_type chip = platform_get_device_id(pdev)->driver_data;
1686         const struct regulator_ops **swops, **hwops;
1687
1688         regmap = dev_get_regmap(pdev->dev.parent, NULL);
1689         if (!regmap) {
1690                 dev_err(&pdev->dev, "No MFD driver data\n");
1691                 return -EINVAL;
1692         }
1693
1694         switch (chip) {
1695         case ROHM_CHIP_TYPE_BD71837:
1696                 reg_data = bd71837_regulators;
1697                 num_reg_data = ARRAY_SIZE(bd71837_regulators);
1698                 swops = &bd71837_swcontrol_ops[0];
1699                 hwops = &bd71837_hwcontrol_ops[0];
1700                 break;
1701         case ROHM_CHIP_TYPE_BD71847:
1702                 reg_data = bd71847_regulators;
1703                 num_reg_data = ARRAY_SIZE(bd71847_regulators);
1704                 swops = &bd71847_swcontrol_ops[0];
1705                 hwops = &bd71847_hwcontrol_ops[0];
1706                 break;
1707         default:
1708                 dev_err(&pdev->dev, "Unsupported chip type\n");
1709                 return -EINVAL;
1710         }
1711
1712         /* Register LOCK release */
1713         err = regmap_update_bits(regmap, BD718XX_REG_REGLOCK,
1714                                  (REGLOCK_PWRSEQ | REGLOCK_VREG), 0);
1715         if (err)
1716                 return dev_err_probe(&pdev->dev, err, "Failed to unlock PMIC\n");
1717
1718         dev_dbg(&pdev->dev, "Unlocked lock register 0x%x\n",
1719                 BD718XX_REG_REGLOCK);
1720
1721         use_snvs = of_property_read_bool(pdev->dev.parent->of_node,
1722                                          "rohm,reset-snvs-powered");
1723
1724         /*
1725          * Change the next stage from poweroff to be READY instead of SNVS
1726          * for all reset types because OTP loading at READY will clear SEL
1727          * bit allowing HW defaults for power rails to be used
1728          */
1729         if (!use_snvs) {
1730                 err = regmap_update_bits(regmap, BD718XX_REG_TRANS_COND1,
1731                                          BD718XX_ON_REQ_POWEROFF_MASK |
1732                                          BD718XX_SWRESET_POWEROFF_MASK |
1733                                          BD718XX_WDOG_POWEROFF_MASK |
1734                                          BD718XX_KEY_L_POWEROFF_MASK,
1735                                          BD718XX_POWOFF_TO_RDY);
1736                 if (err)
1737                         return dev_err_probe(&pdev->dev, err,
1738                                              "Failed to change reset target\n");
1739
1740                 dev_dbg(&pdev->dev, "Changed all resets from SVNS to READY\n");
1741         }
1742
1743         config.dev = pdev->dev.parent;
1744         config.regmap = regmap;
1745         /*
1746          * There are cases when we want to leave the enable-control for
1747          * the HW state machine and use this driver only for voltage control.
1748          * One special case is when we use PMIC_STBY_REQ line from SoC to PMIC
1749          * in order to set the system to SUSPEND state.
1750          *
1751          * If regulator is taken under SW control the regulator state will not
1752          * be affected by PMIC state machine - Eg. regulator is likely to stay
1753          * on even in SUSPEND
1754          */
1755         err = get_special_regulators(pdev->dev.parent, reg_data, num_reg_data,
1756                                      &omit_enable);
1757         if (err)
1758                 return err;
1759
1760         for (i = 0; i < num_reg_data; i++) {
1761
1762                 struct regulator_desc *desc;
1763                 struct regulator_dev *rdev;
1764                 struct bd718xx_regulator_data *r;
1765                 int no_enable_control = omit_enable & (1 << i);
1766
1767                 r = &reg_data[i];
1768                 desc = &r->desc;
1769
1770                 if (no_enable_control)
1771                         desc->ops = hwops[i];
1772                 else
1773                         desc->ops = swops[i];
1774
1775                 rdev = devm_regulator_register(&pdev->dev, desc, &config);
1776                 if (IS_ERR(rdev))
1777                         return dev_err_probe(&pdev->dev, PTR_ERR(rdev),
1778                                              "failed to register %s regulator\n",
1779                                              desc->name);
1780
1781                 /*
1782                  * Regulator register gets the regulator constraints and
1783                  * applies them (set_machine_constraints). This should have
1784                  * turned the control register(s) to correct values and we
1785                  * can now switch the control from PMIC state machine to the
1786                  * register interface
1787                  *
1788                  * At poweroff transition PMIC HW disables EN bit for
1789                  * regulators but leaves SEL bit untouched. So if state
1790                  * transition from POWEROFF is done to SNVS - then all power
1791                  * rails controlled by SW (having SEL bit set) stay disabled
1792                  * as EN is cleared. This will result boot failure if any
1793                  * crucial systems are powered by these rails. We don't
1794                  * enable SW control for crucial regulators if snvs state is
1795                  * used
1796                  */
1797                 if (!no_enable_control && (!use_snvs ||
1798                     !rdev->constraints->always_on ||
1799                     !rdev->constraints->boot_on)) {
1800                         err = regmap_update_bits(regmap, r->init.reg,
1801                                                  r->init.mask, r->init.val);
1802                         if (err)
1803                                 return dev_err_probe(&pdev->dev, err,
1804                                         "Failed to take control for (%s)\n",
1805                                         desc->name);
1806                 }
1807                 for (j = 0; j < r->additional_init_amnt; j++) {
1808                         err = regmap_update_bits(regmap,
1809                                                  r->additional_inits[j].reg,
1810                                                  r->additional_inits[j].mask,
1811                                                  r->additional_inits[j].val);
1812                         if (err)
1813                                 return dev_err_probe(&pdev->dev, err,
1814                                         "Buck (%s) initialization failed\n",
1815                                         desc->name);
1816                 }
1817         }
1818
1819         return err;
1820 }
1821
1822 static const struct platform_device_id bd718x7_pmic_id[] = {
1823         { "bd71837-pmic", ROHM_CHIP_TYPE_BD71837 },
1824         { "bd71847-pmic", ROHM_CHIP_TYPE_BD71847 },
1825         { },
1826 };
1827 MODULE_DEVICE_TABLE(platform, bd718x7_pmic_id);
1828
1829 static struct platform_driver bd718xx_regulator = {
1830         .driver = {
1831                 .name = "bd718xx-pmic",
1832                 .probe_type = PROBE_PREFER_ASYNCHRONOUS,
1833         },
1834         .probe = bd718xx_probe,
1835         .id_table = bd718x7_pmic_id,
1836 };
1837
1838 module_platform_driver(bd718xx_regulator);
1839
1840 MODULE_AUTHOR("Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>");
1841 MODULE_DESCRIPTION("BD71837/BD71847 voltage regulator driver");
1842 MODULE_LICENSE("GPL");
1843 MODULE_ALIAS("platform:bd718xx-pmic");