2 # X86_64_LINT -- config file for checking all the sources, tries to pull in
3 # as much of the source tree as it can.
5 # $FreeBSD: src/sys/i386/conf/LINT,v 1.749.2.144 2003/06/04 17:56:59 sam Exp $
7 # See the kernconf(5) manual page for more information on the format of
10 # NB: You probably don't want to try running a kernel built from this
11 # file. Instead, you should start from X86_64_GENERIC, and add options
12 # from this file as required.
15 # These directives are mandatory. The machine directive specifies the
16 # platform and the machine_arch directive specifies the cpu architecture.
23 # This is the ``identification'' of the kernel. Usually this should
24 # be the same as the name of your kernel.
29 # The `maxusers' parameter controls the static sizing of a number of
30 # internal system tables by a formula defined in subr_param.c. Setting
31 # maxusers to 0 will cause the system to auto-size based on physical
37 # The `makeoptions' parameter allows variables to be passed to the
38 # generated Makefile in the build area.
40 # CONF_CFLAGS gives some extra compiler flags that are added to ${CFLAGS}
41 # after most other flags. Here we use it to inhibit use of non-optimal
42 # gcc builtin functions (e.g., memcmp).
44 # DEBUG happens to be magic.
45 # The following is equivalent to 'config -g KERNELNAME' and creates
46 # 'kernel.debug' compiled with -g debugging as well as a normal
47 # 'kernel'. Use 'make install.debug' to install the debug kernel
48 # but that isn't normally necessary as the debug symbols are not loaded
49 # by the kernel and are not useful there anyway.
51 # KERNEL can be overridden so that you can change the default name of your
54 # MODULES_OVERRIDE can be used to limit modules built to a specific list.
56 # INSTALLSTRIPPED can be set to cause installkernel to install stripped
57 # kernels and modules rather than a kernel and modules with debug symbols.
59 # INSTALLSTRIPPEDMODULES can be set to allow a full debug kernel to be
60 # installed, but to strip the installed modules.
62 makeoptions CONF_CFLAGS=-fno-builtin #Don't allow use of memcmp, etc.
63 #makeoptions DEBUG=-g #Build kernel with gdb(1) debug symbols
64 #makeoptions KERNEL=foo #Build kernel "foo" and install "/foo"
65 # Only build Linux API modules and plus those parts of the sound system I need.
66 #makeoptions MODULES_OVERRIDE="linux sound/snd sound/pcm sound/driver/maestro3"
67 #makeoptions INSTALLSTRIPPED=1
68 #makeoptions INSTALLSTRIPPEDMODULES=1
71 # Certain applications can grow to be larger than the 128M limit
72 # that DragonFly initially imposes. Below are some options to
73 # allow that limit to grow to 256MB, and can be increased further
74 # with changing the parameters. MAXDSIZ is the maximum that the
75 # limit can be set to, and the DFLDSIZ is the default value for
76 # the limit. MAXSSIZ is the maximum that the stack limit can be
77 # set to. You might want to set the default lower than the max,
78 # and explicitly set the maximum with a shell command for processes
79 # that regularly exceed the limit like INND.
81 options MAXDSIZ="(256*1024*1024)"
82 options MAXSSIZ="(256*1024*1024)"
83 options DFLDSIZ="(256*1024*1024)"
86 # BLKDEV_IOSIZE sets the default block size used in user block
87 # device I/O. Note that this value will be overridden by the label
88 # when specifying a block device from a label with a non-0
89 # partition blocksize. The default is PAGE_SIZE.
91 options BLKDEV_IOSIZE=8192
93 # Options for the VM subsystem.
94 options PQ_CACHESIZE=512 # color for 512k/16k cache
96 # This allows you to actually store this configuration file into
97 # the kernel binary itself, where it may be later read by saying:
98 # strings -n 3 /kernel | sed -n 's/^___//p' > MYKERNEL
100 options INCLUDE_CONFIG_FILE # Include this file in kernel
103 # The root device and filesystem type can be compiled in;
104 # this provides a fallback option if the root device cannot
105 # be correctly guessed by the bootstrap code, or an override if
106 # the RB_DFLTROOT flag (-r) is specified when booting the kernel.
108 options ROOTDEVNAME=\"ufs:da0s2e\"
111 #####################################################################
114 # SMP enables building of a Symmetric MultiProcessor Kernel. It will
115 # boot on both SMP and UP boxes.
119 # An SMP kernel will ONLY run on an Intel MP spec. qualified motherboard.
121 # Check the 'Rogue SMP hardware' section to see if additional options
122 # are required by your hardware.
124 #options SMP # Symmetric MultiProcessor Kernel
127 #####################################################################
133 # Options for CPU features.
135 # CPU_AMD64X2_INTR_SPAM tries to route HyperTransport EXTINT and NMI
136 # messages to LINT0 on the local APIC when the BIOS has forgotten to
137 # do that. If this is not done on a multi-core cpu, EXTINT and NMI
138 # get routed to the INTR/NMI pins on *BOTH* cores simultaneously, causing
139 # two INTA ack cycles one of which will almost certainly result in a
140 # spurious interrupt vector being presented. This is often visible as
141 # an unmaskable IRQ 7 which occurs for every normal interrupt that occurs
144 # CPU_DISABLE_SSE disables SSE/MMX2 instructions support.
146 # CPU_ENABLE_EST enables support for Enhanced SpeedStep technology
147 # found in Pentium(tm) M processors.
149 options CPU_AMD64X2_INTR_SPAM
150 #options CPU_DISABLE_SSE
151 options CPU_ENABLE_EST
153 #####################################################################
154 # COMPATIBILITY OPTIONS
157 # Implement system calls compatible with 4.3BSD and older versions of
158 # FreeBSD. You probably do NOT want to remove this as much current code
159 # still relies on the 4.3 emulation.
164 # These three options provide support for System V Interface
165 # Definition-style interprocess communication, in the form of shared
166 # memory, semaphores, and message queues, respectively.
168 # System V shared memory and tunable parameters
169 options SYSVSHM # include support for shared memory
170 options SHMMAXPGS=1025 # max amount of shared memory pages (4k on i386)
171 options SHMALL=1025 # max amount of shared memory (bytes)
172 options SHMMAX="(SHMMAXPGS*PAGE_SIZE+1)"
173 # max shared memory segment size (bytes)
174 options SHMMIN=2 # min shared memory segment size (bytes)
175 options SHMMNI=33 # max number of shared memory identifiers
176 options SHMSEG=9 # max shared memory segments per process
178 # System V semaphores and tunable parameters
179 options SYSVSEM # include support for semaphores
180 options SEMMAP=31 # amount of entries in semaphore map
181 options SEMMNI=11 # number of semaphore identifiers in the system
182 options SEMMNS=61 # number of semaphores in the system
183 options SEMMNU=31 # number of undo structures in the system
184 options SEMMSL=61 # max number of semaphores per id
185 options SEMOPM=101 # max number of operations per semop call
186 options SEMUME=11 # max number of undo entries per process
188 # System V message queues and tunable parameters
189 options SYSVMSG # include support for message queues
190 options MSGMNB=2049 # max characters per message queue
191 options MSGMNI=41 # max number of message queue identifiers
192 options MSGSEG=2049 # max number of message segments in the system
193 options MSGSSZ=16 # size of a message segment MUST be power of 2
194 options MSGTQL=41 # max amount of messages in the system
197 #####################################################################
201 # Enable the kernel debugger.
206 # Print a stack trace on kernel panic.
211 # Don't drop into DDB for a panic. Intended for unattended operation
212 # where you may want to drop to DDB from the console, but still want
213 # the machine to recover from a panic
215 options DDB_UNATTENDED
218 # If using GDB remote mode to debug the kernel, there's a non-standard
219 # extension to the remote protocol that can be used to use the serial
220 # port as both the debugging port and the system console. It's non-
221 # standard and you're on your own if you enable it. See also the
222 # "remotechat" variables in the DragonFly specific version of gdb.
224 options GDB_REMOTE_CHAT
227 # KTRACE enables the system-call tracing facility ktrace(2).
229 options KTRACE #kernel tracing
232 # The INVARIANTS option is used in a number of source files to enable
233 # extra sanity checking of internal structures. This support is not
234 # enabled by default because of the extra time it would take to check
235 # for these conditions, which can only occur as a result of
236 # programming errors.
241 # The DIAGNOSTIC option is used to enable extra debugging information
242 # from some parts of the kernel. As this makes everything more noisy,
243 # it is disabled by default.
248 # PERFMON causes the driver for Pentium/Pentium Pro performance counters
249 # to be compiled. See perfmon(4) for more information.
255 # This option let some drivers co-exist that can't co-exist in a running
256 # system. This is used to be able to compile all kernel code in one go for
257 # quality assurance purposes (like this file, which the option takes it name
260 options COMPILING_LINT
263 # XXX - this doesn't belong here.
264 # Allow ordinary users to take the console - this is useful for X.
268 #####################################################################
273 # Only the INET (Internet) family is officially supported in DragonFly.
274 # Source code for the NS (Xerox Network Service) is provided for amusement
277 options INET #Internet communications protocols
278 options INET6 #IPv6 communications protocols
279 options IPSEC #IP security
280 options IPSEC_ESP #IP security (crypto; define w/ IPSEC)
281 options IPSEC_DEBUG #debug for IP security
283 # Set IPSEC_FILTERGIF to force packets coming through a gif tunnel
284 # to be processed by any configured packet filtering (ipfw, ipf).
285 # The default is that packets coming from a tunnel are _not_ processed;
286 # they are assumed trusted.
288 # Note that enabling this can be problematic as there are no mechanisms
289 # in place for distinguishing packets coming out of a tunnel (e.g. no
290 # encX devices as found on openbsd).
292 #options IPSEC_FILTERGIF #filter ipsec packets from a tunnel
295 # Experimental IPsec implementation that uses the kernel crypto
296 # framework. This cannot be configured together with IPSEC and
297 # (currently) supports only IPv4. To use this you must also
298 # configure the crypto device (see below). Note that with this
299 # you get all the IPsec protocols (e.g. there is no FAST_IPSEC_ESP).
300 # IPSEC_DEBUG is used, as above, to configure debugging support
301 # within the IPsec protocols.
303 #options FAST_IPSEC #new IPsec
305 options IPX #IPX/SPX communications protocols
306 options IPXIP #IPX in IP encapsulation (not available)
307 options IPTUNNEL #IP in IPX encapsulation (not available)
309 options NCP #NetWare Core protocol
311 options MPLS #Multi-Protocol Label Switching
313 options NETATALK #Appletalk communications protocols
317 # NETSMB enables support for SMB protocol, it requires LIBMCHAIN and LIBICONV
319 # NETSMBCRYPTO enables support for encrypted passwords.
320 options NETSMB #SMB/CIFS requester
321 options NETSMBCRYPTO #encrypted password support for SMB
323 # mchain library. It can be either loaded as KLD or compiled into kernel
324 options LIBMCHAIN #mbuf management library
326 # netgraph(4). Enable the base netgraph code with the NETGRAPH option.
327 # Individual node types can be enabled with the corresponding option
328 # listed below; however, this is not strictly necessary as netgraph
329 # will automatically load the corresponding KLD module if the node type
330 # is not already compiled into the kernel. Each type below has a
331 # corresponding man page, e.g., ng_async(4).
332 options NETGRAPH #netgraph(4) system
333 options NETGRAPH_ASYNC
335 options NETGRAPH_BRIDGE
336 options NETGRAPH_CISCO
337 options NETGRAPH_ECHO
338 options NETGRAPH_EIFACE
339 options NETGRAPH_ETHER
340 options NETGRAPH_FRAME_RELAY
341 options NETGRAPH_HOLE
342 options NETGRAPH_IFACE
343 options NETGRAPH_KSOCKET
344 options NETGRAPH_L2TP
346 # MPPC compression requires proprietary files (not included)
347 #options NETGRAPH_MPPC_COMPRESSION
348 options NETGRAPH_MPPC_ENCRYPTION
349 options NETGRAPH_ONE2MANY
351 options NETGRAPH_PPPOE
352 options NETGRAPH_PPTPGRE
353 options NETGRAPH_RFC1490
354 options NETGRAPH_SOCKET
360 device mn # Munich32x/Falc54 Nx64kbit/sec cards.
363 # Network interfaces:
364 # The `loop' pseudo-device is MANDATORY when networking is enabled.
365 # The `ether' pseudo-device provides generic code to handle
366 # Ethernets; it is MANDATORY when a Ethernet device driver is
368 # The `sppp' pseudo-device serves a similar role for certain types
369 # of synchronous PPP links (like `ar').
370 # The `sl' pseudo-device implements the Serial Line IP (SLIP) service.
371 # The `ppp' pseudo-device implements the Point-to-Point Protocol.
372 # The `bpf' pseudo-device enables the Berkeley Packet Filter. Be
373 # aware of the legal and administrative consequences of enabling this
374 # option. The number of devices determines the maximum number of
375 # simultaneous BPF clients programs runnable.
376 # The `disc' pseudo-device implements a minimal network interface,
377 # which throws away all packets sent and never receives any. It is
378 # included for testing purposes. This shows up as the 'ds' interface.
379 # The `tun' pseudo-device implements (user-)ppp and nos-tun
380 # The `gif' pseudo-device implements IPv6 over IP4 tunneling,
381 # IPv4 over IPv6 tunneling, IPv4 over IPv4 tunneling and
382 # IPv6 over IPv6 tunneling.
383 # The `gre' device implements two types of IP4 over IP4 tunneling:
384 # GRE and MOBILE, as specified in the RFC1701 and RFC2004.
385 # The `faith' pseudo-device captures packets sent to it and diverts them
386 # to the IPv4/IPv6 translation daemon.
387 # The `stf' device implements 6to4 encapsulation.
388 # The `ef' pseudo-device provides support for multiple ethernet frame types
389 # specified via ETHER_* options. See ef(4) for details.
391 # The PPP_BSDCOMP option enables support for compress(1) style entire
392 # packet compression, the PPP_DEFLATE is for zlib/gzip style compression.
393 # PPP_FILTER enables code for filtering the ppp data stream and selecting
394 # events for resetting the demand dial activity timer - requires bpf.
395 # See pppd(8) for more details.
397 pseudo-device ether #Generic Ethernet
398 pseudo-device vlan 1 #VLAN support
399 pseudo-device bridge #Bridging support
400 pseudo-device sppp #Generic Synchronous PPP
401 pseudo-device loop #Network loopback device
402 pseudo-device bpf #Berkeley packet filter
403 pseudo-device disc #Discard device (ds0, ds1, etc)
404 pseudo-device tun #Tunnel driver (ppp(8), nos-tun(8))
405 pseudo-device sl 2 #Serial Line IP
406 pseudo-device gre #IP over IP tunneling
407 pseudo-device ppp 2 #Point-to-point protocol
408 options PPP_BSDCOMP #PPP BSD-compress support
409 options PPP_DEFLATE #PPP zlib/deflate/gzip support
410 options PPP_FILTER #enable bpf filtering (needs bpf)
412 pseudo-device ef # Multiple ethernet frames support
413 options ETHER_II # enable Ethernet_II frame
414 options ETHER_8023 # enable Ethernet_802.3 (Novell) frame
415 options ETHER_8022 # enable Ethernet_802.2 frame
416 options ETHER_SNAP # enable Ethernet_802.2/SNAP frame
419 pseudo-device gif #IPv6 and IPv4 tunneling
420 pseudo-device faith 1 #for IPv6 and IPv4 translation
421 pseudo-device stf #6to4 IPv6 over IPv4 encapsulation
424 # Internet family options:
426 # MROUTING enables the kernel multicast packet forwarder, which works
429 # PIM enables Protocol Independent Multicast in the kernel.
430 # Requires MROUTING enabled.
432 # IPFIREWALL enables support for IP firewall construction, in
433 # conjunction with the `ipfw' program. IPFIREWALL_VERBOSE sends
434 # logged packets to the system logger. IPFIREWALL_VERBOSE_LIMIT
435 # limits the number of times a matching entry can be logged.
437 # WARNING: IPFIREWALL defaults to a policy of "deny ip from any to any"
438 # and if you do not add other rules during startup to allow access,
439 # YOU WILL LOCK YOURSELF OUT. It is suggested that you set firewall_type=open
440 # in /etc/rc.conf when first enabling this feature, then refining the
441 # firewall rules in /etc/rc.firewall after you've tested that the new kernel
442 # feature works properly.
444 # IPFIREWALL_DEFAULT_TO_ACCEPT causes the default rule (at boot) to
445 # allow everything. Use with care, if a cracker can crash your
446 # firewall machine, they can get to your protected machines. However,
447 # if you are using it as an as-needed filter for specific problems as
448 # they arise, then this may be for you. Changing the default to 'allow'
449 # means that you won't get stuck if the kernel and /sbin/ipfw binary get
452 # IPDIVERT enables the divert IP sockets, used by ``ipfw divert''
454 # IPSTEALTH enables code to support stealth forwarding (i.e., forwarding
455 # packets without touching the ttl). This can be useful to hide firewalls
456 # from traceroute and similar tools.
458 # TCPDEBUG is undocumented.
460 options MROUTING # Multicast routing
461 options PIM # Protocol Independent Multicast
462 options IPFIREWALL #firewall
463 options IPFIREWALL_DEBUG #debug prints
464 options IPFIREWALL_VERBOSE #enable logging to syslogd(8)
465 options IPFIREWALL_FORWARD #enable transparent proxy support
466 options IPFIREWALL_VERBOSE_LIMIT=100 #limit verbosity
467 options IPFIREWALL_DEFAULT_TO_ACCEPT #allow everything by default
468 options IPV6FIREWALL #firewall for IPv6
469 options IPV6FIREWALL_VERBOSE
470 options IPV6FIREWALL_VERBOSE_LIMIT=100
471 options IPV6FIREWALL_DEFAULT_TO_ACCEPT
472 options IPDIVERT #divert sockets
473 options IPSTEALTH #support for stealth forwarding
483 # The MBUF_STRESS_TEST option enables options which create
484 # various random failures / extreme cases related to mbuf
485 # functions. See the mbuf(9) manpage for a list of available
487 options MBUF_STRESS_TEST
489 # Statically link in accept filters
490 options ACCEPT_FILTER_DATA
491 options ACCEPT_FILTER_HTTP
493 # TCP_SIGNATURE adds support for RFC 2385 (TCP-MD5) digests. These are
494 # carried in TCP option 19. This option is commonly used to protect
495 # TCP sessions (e.g. BGP) where IPSEC is not available nor desirable.
496 # This is enabled on a per-socket basis using the TCP_MD5SIG socket option.
497 # This requires the use of 'device crypto', 'options IPSEC'
498 # or 'device cryptodev'.
499 options TCP_SIGNATURE #include support for RFC 2385
502 # TCP_DROP_SYNFIN adds support for ignoring TCP packets with SYN+FIN. This
503 # prevents nmap et al. from identifying the TCP/IP stack, but breaks support
504 # for RFC1644 extensions and is not recommended for web servers.
506 options TCP_DROP_SYNFIN #drop TCP packets with SYN+FIN
508 # ICMP_BANDLIM enables icmp error response bandwidth limiting. You
509 # typically want this option as it will help protect the machine from
510 # D.O.S. packet attacks.
514 # DUMMYNET enables the "dummynet" bandwidth limiter. You need
515 # IPFIREWALL as well. See the dummynet(4) and ipfw(8) manpages for more info.
518 options DUMMYNET_DEBUG
521 # ATM (HARP version) options
523 # ATM_CORE includes the base ATM functionality code. This must be included
526 # ATM_IP includes support for running IP over ATM.
528 # At least one (and usually only one) of the following signalling managers
529 # must be included (note that all signalling managers include PVC support):
530 # ATM_SIGPVC includes support for the PVC-only signalling manager `sigpvc'.
531 # ATM_SPANS includes support for the `spans' signalling manager, which runs
532 # the FORE Systems's proprietary SPANS signalling protocol.
533 # ATM_UNI includes support for the `uni30' and `uni31' signalling managers,
534 # which run the ATM Forum UNI 3.x signalling protocols.
536 # The `hea' driver provides support for the Efficient Networks, Inc.
537 # ENI-155p ATM PCI Adapter.
539 # The `hfa' driver provides support for the FORE Systems, Inc.
540 # PCA-200E ATM PCI Adapter.
542 #options ATM_CORE #core ATM protocol family
543 #options ATM_IP #IP over ATM support
544 #options ATM_SIGPVC #SIGPVC signalling manager
545 #options ATM_SPANS #SPANS signalling manager
546 #options ATM_UNI #UNI signalling manager
547 #device hea #Efficient ENI-155p ATM PCI
548 #device hfa #FORE PCA-200E ATM PCI
550 # DEVICE_POLLING adds support for mixed interrupt-polling handling
551 # of network device drivers, which has significant benefits in terms
552 # of robustness to overloads and responsivity, as well as permitting
553 # accurate scheduling of the CPU time between kernel network processing
554 # and other activities. The drawback is a moderate (up to 1/pollhz seconds)
555 # potential increase in response times. See polling(4) for further details.
557 options DEVICE_POLLING
559 # IFPOLL_ENABLE adds hardware queues' based polling
560 options IFPOLL_ENABLE
563 #####################################################################
567 # Only the root, /usr, and /tmp filesystems need be statically
568 # compiled; everything else will be automatically loaded at mount
569 # time. (Exception: the UFS family --- FFS, and MFS ---
570 # cannot currently be demand-loaded.) Some people still prefer
571 # to statically compile other filesystems as well.
573 # NB: The PORTAL and UNION filesystems are known to be
574 # buggy, and WILL panic your system if you attempt to do anything with
575 # them. They are included here as an incentive for some enterprising
576 # soul to sit down and fix them.
579 # One of these is mandatory:
580 options FFS #Fast filesystem
581 options MFS #Memory filesystem
582 options NFS #Network filesystem
584 # The rest are optional:
585 #options NFS_NOSERVER #Disable the NFS-server code.
586 options CD9660 #ISO 9660 filesystem
587 options FDESC #File descriptor filesystem
588 options HPFS #OS/2 File system
589 options MSDOSFS #MS DOS filesystem
590 options NTFS #NT filesystem
591 options NULLFS #NULL filesystem
592 options NWFS #NetWare filesystem
593 options PORTAL #Portal filesystem
594 options PROCFS #Process filesystem
595 options SMBFS #SMB/CIFS filesystem
596 options UDF #UDF filesystem
597 options HAMMER #HAMMER filesystem
598 options TMPFS #Temporary filesystem
600 # YYY-DR Till we rework the VOP methods for this filesystem
601 #options UNION #Union filesystem
602 # The xFS_ROOT options REQUIRE the associated ``options xFS''
603 options FFS_ROOT #FFS usable as root device
604 options NFS_ROOT #NFS usable as root device
606 # Soft updates is technique for improving UFS filesystem speed and
607 # making abrupt shutdown less risky.
610 # Directory hashing improves the speed of operations on very large
611 # directories at the expense of some memory.
614 # Make space in the kernel for a root filesystem on a md device.
615 # Define to the number of kilobytes to reserve for the filesystem.
616 options MD_ROOT_SIZE=10
618 # Make the md device a potential root device, either with preloaded
619 # images of type mfs_root or md_root.
622 # Specify double the default maximum size for malloc(9)-backed md devices.
623 options MD_NSECT=40000
625 # Allow this many swap-devices.
627 # In order to manage swap, the system must reserve bitmap space that
628 # scales with the largest mounted swap device multiplied by NSWAPDEV,
629 # regardless of whether other swap devices exist or not. So it
630 # is not a good idea to make this value too large.
633 # Disk quotas are supported when this option is enabled.
634 options QUOTA #enable disk quotas
636 # If you are running a machine just as a fileserver for PC and MAC
637 # users, using SAMBA or Netatalk, you may consider setting this option
638 # and keeping all those users' directories on a filesystem that is
639 # mounted with the suiddir option. This gives new files the same
640 # ownership as the directory (similar to group). It's a security hole
641 # if you let these users run programs, so confine it to file-servers
642 # (but it'll save you lots of headaches in those cases). Root owned
643 # directories are exempt and X bits are cleared. The suid bit must be
644 # set on the directory as well; see chmod(1) PC owners can't see/set
645 # ownerships so they keep getting their toes trodden on. This saves
646 # you all the support calls as the filesystem it's used on will act as
647 # they expect: "It's my dir so it must be my file".
652 options NFS_MINATTRTIMO=3 # VREG attrib cache timeout in sec
653 options NFS_MAXATTRTIMO=60
654 options NFS_MINDIRATTRTIMO=30 # VDIR attrib cache timeout in sec
655 options NFS_MAXDIRATTRTIMO=60
656 options NFS_GATHERDELAY=10 # Default write gather delay (msec)
657 options NFS_UIDHASHSIZ=29 # Tune the size of nfssvc_sock with this
658 options NFS_WDELAYHASHSIZ=16 # and with this
659 options NFS_MUIDHASHSIZ=63 # Tune the size of nfsmount with this
660 options NFS_DEBUG # Enable NFS Debugging
663 options MSDOSFS_DEBUG # Enable MSDOSFS Debugging
666 # Add support for the EXT2FS filesystem of Linux fame. Be a bit
667 # careful with this - the ext2fs code has a tendency to lag behind
668 # changes and not be exercised very much, so mounting read/write could
669 # be dangerous (and even mounting read only could result in panics.)
673 # Optional character code conversion support with LIBICONV.
674 # Each option requires their base file system and LIBICONV.
676 options MSDOSFS_ICONV
680 #####################################################################
683 # Real time extensions added in the 1993 Posix
684 # P1003_1B: Infrastructure
685 # _KPOSIX_PRIORITY_SCHEDULING: Build in _POSIX_PRIORITY_SCHEDULING
686 # _KPOSIX_VERSION: Version kernel is built for
689 options _KPOSIX_PRIORITY_SCHEDULING
690 options _KPOSIX_VERSION=199309L
693 #####################################################################
696 # The granularity of operation is controlled by the kernel option HZ whose
697 # default value (100) means a granularity of 10ms (1s/HZ).
698 # Consider, however, that reducing the granularity too much might
699 # cause excessive overhead in clock interrupt processing,
700 # potentially causing ticks to be missed and thus actually reducing
701 # the accuracy of operation.
705 # The following options are used for debugging clock behavior only, and
706 # should not be used for production systems.
708 # CLK_CALIBRATION_LOOP will run the clock calibration loop at startup
709 # until the user presses a key.
711 #options CLK_CALIBRATION_LOOP
713 # The following two options measure the frequency of the corresponding
714 # clock relative to the RTC (onboard mc146818a).
716 #options CLK_USE_I8254_CALIBRATION
717 #options CLK_USE_TSC_CALIBRATION
720 #####################################################################
723 # SCSI DEVICE CONFIGURATION
725 # The SCSI subsystem consists of the `base' SCSI code, a number of
726 # high-level SCSI device `type' drivers, and the low-level host-adapter
727 # device drivers. The host adapters are listed in the ISA and PCI
728 # device configuration sections below.
730 # Beginning with FreeBSD 2.0.5 you can wire down your SCSI devices so
731 # that a given bus, target, and LUN always come on line as the same
732 # device unit. In earlier versions the unit numbers were assigned
733 # in the order that the devices were probed on the SCSI bus. This
734 # means that if you removed a disk drive, you may have had to rewrite
735 # your /etc/fstab file, and also that you had to be careful when adding
736 # a new disk as it may have been probed earlier and moved your device
737 # configuration around.
739 # This old behavior is maintained as the default behavior. The unit
740 # assignment begins with the first non-wired down unit for a device
741 # type. For example, if you wire a disk as "da3" then the first
742 # non-wired disk will be assigned da4.
744 # The syntax for wiring down devices is:
746 # device scbus0 at ahc0 # Single bus device
747 # device scbus1 at ahc1 bus 0 # Single bus device
748 # device scbus3 at ahc2 bus 0 # Twin bus device
749 # device scbus2 at ahc2 bus 1 # Twin bus device
750 # device da0 at scbus0 target 0 unit 0
751 # device da1 at scbus3 target 1
752 # device da2 at scbus2 target 3
753 # device sa1 at scbus1 target 6
756 # "units" (SCSI logical unit number) that are not specified are
757 # treated as if specified as LUN 0.
759 # All SCSI devices allocate as many units as are required.
761 # The "unknown" device (uk? in pre-2.0.5) is now part of the base SCSI
762 # configuration and doesn't have to be explicitly configured.
764 device scbus #base SCSI code
765 device ch #SCSI media changers
766 device da #SCSI direct access devices (aka disks)
767 device sa #SCSI tapes
768 device cd #SCSI CD-ROMs
769 device pass #CAM passthrough driver
770 device sg #Passthrough device (linux scsi generic)
771 device pt #SCSI processor type
772 device ses #SCSI SES/SAF-TE driver
774 # Options for device mapper
776 device dm_target_crypt
777 device dm_target_linear
778 device dm_target_striped
781 device iscsi_initiator
782 options ISCSI_INITIATOR_DEBUG=8
786 # -- NOTE -- If you specify one of the bus/target/lun options, you must
788 # CAMDEBUG: When defined enables debugging macros
789 # CAM_DEBUG_BUS: Debug the given bus. Use -1 to debug all busses.
790 # CAM_DEBUG_TARGET: Debug the given target. Use -1 to debug all targets.
791 # CAM_DEBUG_LUN: Debug the given lun. Use -1 to debug all luns.
792 # CAM_DEBUG_FLAGS: OR together CAM_DEBUG_INFO, CAM_DEBUG_TRACE,
793 # CAM_DEBUG_SUBTRACE, and CAM_DEBUG_CDB
795 # CAM_MAX_HIGHPOWER: Maximum number of concurrent high power (start unit) cmds
796 # SCSI_NO_SENSE_STRINGS: When defined disables sense descriptions
797 # SCSI_NO_OP_STRINGS: When defined disables opcode descriptions
798 # SCSI_DELAY: The number of MILLISECONDS to freeze the SIM (scsi adapter)
799 # queue after a bus reset, and the number of milliseconds to
800 # freeze the device queue after a bus device reset. This
801 # can be changed at boot and runtime with the
802 # kern.cam.scsi_delay tunable/sysctl.
804 options CAM_DEBUG_BUS=-1
805 options CAM_DEBUG_TARGET=-1
806 options CAM_DEBUG_LUN=-1
807 options CAM_DEBUG_FLAGS="CAM_DEBUG_INFO|CAM_DEBUG_TRACE|CAM_DEBUG_CDB"
808 options CAM_MAX_HIGHPOWER=4
809 options SCSI_NO_SENSE_STRINGS
810 options SCSI_NO_OP_STRINGS
811 options SCSI_DELAY=8000 # Be pessimistic about Joe SCSI device
813 # Options for the CAM CDROM driver:
814 # CHANGER_MIN_BUSY_SECONDS: Guaranteed minimum time quantum for a changer LUN
815 # CHANGER_MAX_BUSY_SECONDS: Maximum time quantum per changer LUN, only
816 # enforced if there is I/O waiting for another LUN
817 # The compiled in defaults for these variables are 2 and 10 seconds,
820 # These can also be changed on the fly with the following sysctl variables:
821 # kern.cam.cd.changer.min_busy_seconds
822 # kern.cam.cd.changer.max_busy_seconds
824 options CHANGER_MIN_BUSY_SECONDS=2
825 options CHANGER_MAX_BUSY_SECONDS=10
827 # Options for the CAM sequential access driver:
828 # SA_IO_TIMEOUT: Timeout for read/write/wfm operations, in minutes
829 # SA_SPACE_TIMEOUT: Timeout for space operations, in minutes
830 # SA_REWIND_TIMEOUT: Timeout for rewind operations, in minutes
831 # SA_ERASE_TIMEOUT: Timeout for erase operations, in minutes
832 # SA_1FM_AT_EOD: Default to model which only has a default one filemark at EOT.
833 options SA_IO_TIMEOUT="(4)"
834 options SA_SPACE_TIMEOUT="(60)"
835 options SA_REWIND_TIMEOUT="(2*60)"
836 options SA_ERASE_TIMEOUT="(4*60)"
837 options SA_1FM_AT_EOD
839 # Optional timeout for the CAM processor target (pt) device
840 # This is specified in seconds. The default is 60 seconds.
841 options SCSI_PT_DEFAULT_TIMEOUT="60"
843 # Optional enable of doing SES passthrough on other devices (e.g., disks)
845 # Normally disabled because a lot of newer SCSI disks report themselves
846 # as having SES capabilities, but this can then clot up attempts to build
847 # build a topology with the SES device that's on the box these drives
849 options SES_ENABLE_PASSTHROUGH
852 #####################################################################
853 # MISCELLANEOUS DEVICES AND OPTIONS
855 # The `pty' device usually turns out to be ``effectively mandatory'',
856 # as it is required for `telnetd', `rlogind', `screen', `emacs', and
857 # `xterm', among others.
859 pseudo-device pty #Pseudo ttys
860 pseudo-device gzip #Exec gzipped a.out's
861 pseudo-device vn #Vnode driver (turns a file into a device)
862 pseudo-device md #Memory/malloc disk
863 pseudo-device snp #Snoop device - to look at pty/vty/etc..
864 pseudo-device ccd 4 #Concatenated disk driver
866 # Configuring Vinum into the kernel is not necessary, since the kld
867 # module gets started automatically when vinum(8) starts. This
868 # device is also untested. Use at your own risk.
870 # The option VINUMDEBUG must match the value set in CFLAGS
871 # in src/sbin/vinum/Makefile. Failure to do so will result in
872 # the following message from vinum(8):
874 # Can't get vinum config: Invalid argument
876 # see vinum(4) for more reasons not to use these options.
877 pseudo-device vinum #Vinum concat/mirror/raid driver
878 #options VINUMDEBUG #enable Vinum debugging hooks
880 # Kernel side iconv library
883 # Size of the kernel message buffer. Should be N * pagesize.
884 options MSGBUF_SIZE=40960
887 #####################################################################
888 # HARDWARE DEVICE CONFIGURATION
893 # Mandatory ISA devices: isa
900 # AUTO_EOI_1 enables the `automatic EOI' feature for the master 8259A
901 # interrupt controller. This saves about 0.7-1.25 usec for each interrupt.
902 # This option breaks suspend/resume on some portables.
904 # AUTO_EOI_2 enables the `automatic EOI' feature for the slave 8259A
905 # interrupt controller. This saves about 0.7-1.25 usec for each interrupt.
906 # Automatic EOI is documented not to work for for the slave with the
907 # original i8259A, but it works for some clones and some integrated
910 # MAXMEM specifies the amount of RAM on the machine; if this is not
911 # specified, DragonFly will first read the amount of memory from the CMOS
912 # RAM, so the amount of memory will initially be limited to 64MB or 16MB
913 # depending on the BIOS. If the BIOS reports 64MB, a memory probe will
914 # then attempt to detect the installed amount of RAM. If this probe
915 # fails to detect >64MB RAM you will have to use the MAXMEM option.
916 # The amount is in kilobytes, so for a machine with 128MB of RAM, it would
917 # be 131072 (128 * 1024).
919 # BROKEN_KEYBOARD_RESET disables the use of the keyboard controller to
920 # reset the CPU for reboot. This is needed on some systems with broken
921 # keyboard controllers.
925 options MAXMEM="(128*1024)"
926 #options BROKEN_KEYBOARD_RESET
928 # Enable support for the kernel PLL to use an external PPS signal,
929 # under supervision of [x]ntpd(8)
930 # More info in ntpd documentation: http://www.eecis.udel.edu/~ntp
934 # The keyboard controller; it controls the keyboard and the PS/2 mouse.
935 device atkbdc0 at isa? port IO_KBD
938 device atkbd0 at atkbdc? irq 1
941 options ATKBD_DFLT_KEYMAP # specify the built-in keymap
942 makeoptions ATKBD_DFLT_KEYMAP="jp.106"
944 # These options are valid for other keyboard drivers as well.
945 options KBD_DISABLE_KEYMAP_LOAD # refuse to load a keymap
946 options KBD_INSTALL_CDEV # install a CDEV entry in /dev
949 # 0x01 Force detection of keyboard, else we always assume a keyboard
950 # 0x02 Don't reset keyboard, useful for some newer ThinkPads
951 # 0x03 Force detection and avoid reset, might help with certain
953 # 0x04 Old-style (XT) keyboard support, useful for older ThinkPads
956 device psm0 at atkbdc? irq 12
959 options PSM_HOOKRESUME #hook the system resume event, useful
961 options PSM_RESETAFTERSUSPEND #reset the device at the resume event
963 device kbdmux # keyboard multiplexer
965 # The video card driver.
969 # Try the following option if the mouse pointer is not drawn correctly
970 # or font does not seem to be loaded properly. May cause flicker on
972 options VGA_ALT_SEQACCESS
974 options VGA_DEBUG=2 # enable VGA debug output
976 # If you experience problems switching back to 80x25 (or a derived mode),
977 # the following option might help.
978 #options VGA_KEEP_POWERON_MODE # use power-on settings for 80x25
980 # If you can dispense with some vga driver features, you may want to
981 # use the following options to save some memory.
982 #options VGA_NO_FONT_LOADING # don't save/load font
983 #options VGA_NO_MODE_CHANGE # don't change video modes
985 # The following option probably won't work with the LCD displays.
986 options VGA_WIDTH90 # support 90 column modes
988 # Splash screen at start up! Screen savers require this too.
991 # The syscons console driver (sco color console compatible).
993 options MAXCONS=16 # number of virtual consoles
994 options SC_ALT_MOUSE_IMAGE # simplified mouse cursor in text mode
995 options SC_DEBUG_LEVEL=5 # enable debug output
996 options SC_DFLT_FONT # compile font in
997 makeoptions SC_DFLT_FONT=cp850
998 options SC_DISABLE_DDBKEY # disable `debug' key
999 options SC_DISABLE_REBOOT # disable reboot key sequence
1000 options SC_HISTORY_SIZE=200 # number of history buffer lines
1001 options SC_MOUSE_CHAR=0x3 # char code for text mode mouse cursor
1002 options SC_PIXEL_MODE # add support for the raster text mode
1004 # The following options will let you change the default colors of syscons.
1005 options SC_NORM_ATTR="(FG_GREEN|BG_BLACK)"
1006 options SC_NORM_REV_ATTR="(FG_YELLOW|BG_GREEN)"
1007 options SC_KERNEL_CONS_ATTR="(FG_RED|BG_BLACK)"
1008 options SC_KERNEL_CONS_REV_ATTR="(FG_BLACK|BG_RED)"
1010 # If you have a two button mouse, you may want to add the following option
1011 # to use the right button of the mouse to paste text.
1012 options SC_TWOBUTTON_MOUSE
1014 # You can selectively disable features in syscons.
1015 #options SC_NO_CUTPASTE
1016 #options SC_NO_FONT_LOADING
1017 #options SC_NO_HISTORY
1018 #options SC_NO_SYSMOUSE
1021 # Optional ISA devices:
1025 # SCSI host adapters: `aha', `aic', `bt'
1027 # adv: All Narrow SCSI bus AdvanSys controllers.
1028 # adw: Second Generation AdvanSys controllers including the ADV940UW.
1030 # ahc: Adaptec 274x/284x/294x
1032 # bt: Most Buslogic controllers
1033 # ncv: NCR 53C500 based SCSI host adapters.
1034 # nsp: Workbit Ninja SCSI-3 based PC Card SCSI host adapters.
1035 # stg: TMC 18C30, 18C50 based ISA/PC Card SCSI host adapters.
1037 # Note that the order is important in order for Buslogic cards to be
1041 device bt0 at isa? port IO_BT0
1048 device stg0 at isa? port 0x140 irq 11
1051 # Adaptec FSA RAID controllers, including integrated DELL controller,
1052 # the Dell PERC 2/QC and the HP NetRAID-4M
1056 device aacp # SCSI Passthrough interface (optional, CAM required)
1059 # Compaq Smart RAID, Mylex DAC960 and AMI MegaRAID controllers. Only
1060 # one entry is needed; the code will find and configure all supported
1063 device ida # Compaq Smart RAID
1064 device mlx # Mylex DAC960
1065 device amr # AMI MegaRAID
1066 device amrp # SCSI Passthrough interface (optional, CAM req.)
1067 device mfi # LSI MegaRAID SAS
1068 device mfip # LSI MegaRAID SAS passthrough, requires CAM
1072 # Areca RAID (CAM is required).
1074 device arcmsr # Areca SATA II RAID
1077 # Highpoint RocketRAID 182x.
1081 # Highpoint RocketRaid 3xxx series SATA RAID
1087 device twe # 3ware ATA RAID
1088 device twa # 3ware 9000 series PATA/SATA RAID
1089 options TWA_DEBUG=10 # enable debug messages
1090 device tws # 3ware 9750 series SATA/SAS RAID
1093 # Promise Supertrack SX6000
1103 # The 'ATA' driver supports all ATA and ATAPI devices.
1104 # You only need one "device ata" for it to find all
1105 # PCI ATA/ATAPI devices on modern machines.
1107 #device atadisk # ATA disk drives
1108 #device atapicd # ATAPI CDROM drives
1109 #device atapifd # ATAPI floppy drives
1110 #device atapist # ATAPI tape drives
1111 #device atapicam # emulate ATAPI devices as SCSI ditto via CAM
1112 # needs CAM to be present (scbus & pass)
1113 # AHCI driver, this will override NATA for AHCI devices,
1114 # both drivers may be included.
1118 # SiI3124/3132 driver
1122 # The 'NATA' set of drivers are set to replace the previous ATA drivers,
1123 # and this set of drivers is mutually exclusive with the old ones. This means,
1124 # you can't have both at the same time!
1126 device natadisk # ATA disk drives
1127 device natapicd # ATAPI CD/DVD drives
1128 device natapifd # ATAPI floppy drives
1129 device natapist # ATAPI tape drives
1130 device natapicam # ATAPI CAM layer emulation
1131 device nataraid # support for ATA software RAID controllers
1132 device natausb # ATA-over-USB support
1134 #The following options are valid on the ATA & NATA drivers:
1136 # ATA_STATIC_ID: controller numbering is static (like the old driver)
1137 # else the device numbers are dynamically allocated.
1138 options ATA_STATIC_ID
1141 # For older non-PCI systems, these are the lines to use:
1142 #device ata0 at isa? port IO_WD1 irq 14
1143 #device ata1 at isa? port IO_WD2 irq 15
1146 # Standard floppy disk controllers: `fdc' and `fd'
1148 #device fdc0 at isa? port IO_FD1 irq 6 drq 2
1150 # FDC_DEBUG enables floppy debugging. Since the debug output is huge, you
1151 # gotta turn it actually on by setting the variable fd_debug with DDB,
1155 #device fd0 at fdc0 drive 0
1156 #device fd1 at fdc0 drive 1
1159 # Other standard PC hardware: `sio', etc.
1161 # sio: serial ports (see sio(4))
1163 device sio0 at isa? port IO_COM1 flags 0x10 irq 4
1166 # `flags' for serial drivers that support consoles (only for sio now):
1167 # 0x10 enable console support for this unit. The other console flags
1168 # are ignored unless this is set. Enabling console support does
1169 # not make the unit the preferred console - boot with -h or set
1170 # the 0x20 flag for that. Currently, at most one unit can have
1171 # console support; the first one (in config file order) with
1172 # this flag set is preferred. Setting this flag for sio0 gives
1173 # the old behaviour.
1174 # 0x20 force this unit to be the console (unless there is another
1175 # higher priority console). This replaces the COMCONSOLE option.
1176 # 0x40 reserve this unit for low level console operations. Do not
1177 # access the device in any normal way.
1178 # 0x80 use this port for serial line gdb support in ddb.
1180 # PnP `flags' (set via userconfig using pnp x flags y)
1181 # 0x1 disable probing of this device. Used to prevent your modem
1182 # from being attached as a PnP modem.
1185 # Options for serial drivers that support consoles (only for sio now):
1186 options BREAK_TO_DEBUGGER #a BREAK on a comconsole goes to
1188 options CONSPEED=115200 # speed for serial console
1191 # Solaris implements a new BREAK which is initiated by a character
1192 # sequence CR ~ ^b which is similar to a familiar pattern used on
1193 # Sun servers by the Remote Console.
1194 options ALT_BREAK_TO_DEBUGGER
1197 options COM_ESP #code for Hayes ESP
1198 options COM_MULTIPORT #code for some cards with shared IRQs
1200 # Other flags for sio that aren't documented in the man page.
1201 # 0x20000 enable hardware RTS/CTS and larger FIFOs. Only works for
1202 # ST16650A-compatible UARTs.
1205 # Network interfaces: `ed', `ep', `ie', `is', `lnc'
1207 # cs: IBM Etherjet and other Crystal Semi CS89x0-based adapters
1208 # ed: Western Digital and SMC 80xx; Novell NE1000 and NE2000; 3Com 3C503
1210 # ex: Intel EtherExpress Pro/10 and other i82595-based adapters
1211 # fe: Fujitsu MB86960A/MB86965A Ethernet
1212 # ie: AT&T StarLAN 10 and EN100; 3Com 3C507; unknown NI5210; Intel EtherExpress
1213 # lnc: Lance/PCnet cards (Isolan, Novell NE2100, NE32-VL, AMD Am7990 & Am79C960)
1214 # sbsh: Granch SBNI16 SHDSL modem PCI adapters
1215 # wi: Lucent WaveLAN/IEEE 802.11 PCMCIA adapters. Note: this supports both
1216 # the PCMCIA and ISA cards: the ISA card is really a PCMCIA to ISA
1217 # bridge with a PCMCIA adapter plugged into it.
1218 # an: Aironet 4500/4800 802.11 wireless adapters. Supports the PCMCIA,
1219 # PCI and ISA varieties.
1220 # xe: Xircom/Intel EtherExpress Pro100/16 PC Card ethernet controller.
1222 device cs0 at isa? port 0x300
1223 device ed0 at isa? port 0x280 irq 5 iomem 0xd8000
1226 device ie0 at isa? port 0x300 irq 5 iomem 0xd0000
1227 device ie1 at isa? port 0x360 irq 7 iomem 0xd0000
1228 device lnc0 at isa? port 0x280 irq 10 drq 0
1230 device sn0 at isa? port 0x300 irq 10
1232 # Wlan support is mandatory for some wireless LAN devices.
1233 options IEEE80211_DEBUG #enable debugging msgs
1234 options IEEE80211_AMPDU_AGE #age frames in AMPDU reorder q's
1235 options IEEE80211_SUPPORT_MESH #enable 802.11s D3.0 support
1236 options IEEE80211_SUPPORT_TDMA #enable TDMA support
1237 device wlan # 802.11 support
1238 device wlan_acl # 802.11 MAC-based access control for AP
1239 device wlan_ccmp # 802.11 CCMP support
1240 device wlan_tkip # 802.11 TKIP support
1241 device wlan_wep # 802.11 WEP support
1242 device wlan_xauth # 802.11 WPA or 802.1x authentication for AP
1243 device wlan_amrr # 802.11 AMRR TX rate control algorithm
1244 device an # Aironet Communications 4500/4800
1245 device ath # Atheros AR521x
1246 options AH_SUPPORT_AR5416
1247 device ath_hal # Atheros Hardware Access Layer
1248 #device ath_rate_amrr # Atheros AMRR TX rate control algorithm
1249 #device ath_rate_onoe # Atheros Onoe TX rate control algorithm
1250 device ath_rate_sample # Atheros Sample TX rate control algorithm
1251 options ATH_DEBUG # turn on debugging output (see hw.ath.debug)
1252 options ATH_DIAGAPI # diagnostic interface to the HAL
1253 options ATH_RXBUF=80 # number of RX buffers to allocate
1254 options ATH_TXBUF=400 # number of TX buffers to allocate
1255 #device iwl # Intel PRO/Wireless 2100
1256 device iwi # Intel PRO/Wireless 2200BG/2915ABG
1257 device iwn # Intel WiFi Link 4965/1000/5000/5150/5300/6000/6050
1258 device wi # WaveLAN/IEEE, PRISM-II, Spectrum24 802.11DS
1259 #device rtw # RealTek 8180
1260 #device acx # TI ACX100/ACX111.
1261 device xe # Xircom PCMCIA
1262 device ral # Ralink Technology 802.11 wireless NIC
1265 # IEEE 802.11 adapter firmware modules
1267 # iwifw: Intel PRO/Wireless 2200BG/2225BG/2915ABG firmware
1268 # iwnfw: Intel WiFi Link 4965/1000/5000/5150/5300/6000/6050
1269 # ralfw: Ralink Technology RT25xx and RT26xx firmware
1270 # wpifw: Intel 3945ABG Wireless LAN Controller firmware
1277 # Bluetooth Protocols
1281 # ATM related options
1283 # The `en' device provides support for Efficient Networks (ENI)
1284 # ENI-155 PCI midway cards, and the Adaptec 155Mbps PCI ATM cards (ANA-59x0).
1286 # atm pseudo-device provides generic atm functions and is required for
1288 # NATM enables the netnatm protocol family that can be used to
1291 # the current driver supports only PVC operations (no atm-arp, no multicast).
1292 # for more details, please read the original documents at
1293 # http://www.ccrc.wustl.edu/pub/chuck/tech/bsdatm/bsdatm.html
1297 options NATM #native ATM
1301 # The flags of the device tells the device a bit more info about the
1302 # device that normally is obtained through the PnP interface.
1303 # bit 2..0 secondary DMA channel;
1304 # bit 4 set if the board uses two dma channels;
1305 # bit 15..8 board type, overrides autodetection; leave it
1306 # zero if don't know what to put in (and you don't,
1307 # since this is unsupported at the moment...).
1309 # This driver will use the new PnP code if it's available. You might
1310 # need PNPBIOS for ISA devices.
1312 # If you have a GUS-MAX card and want to use the CS4231 codec on the
1313 # card the drqs for the gus max must be 8 bit (1, 2, or 3).
1315 # If you would like to use the full duplex option on the gus, then define
1316 # flags to be the ``read dma channel''.
1319 # Basic sound card support:
1321 # For PnP/PCI sound cards:
1323 device "snd_als4000"
1329 device "snd_emu10k1"
1335 device "snd_maestro"
1336 device "snd_maestro3"
1338 device "snd_neomagic"
1343 device "snd_t4dwave"
1344 device "snd_via8233"
1345 device "snd_via82c686"
1347 # For non-pnp sound cards:
1348 device pcm0 at isa? irq 10 drq 1 flags 0x0
1353 # Miscellaneous hardware:
1355 # bktr: Brooktree bt848/848a/849a/878/879 video capture and TV Tuner board
1357 # rp: Comtrol Rocketport(ISA) - single card
1358 # si: Specialix SI/XIO 4-32 port terminal multiplexor
1359 # nmdm: nullmodem terminal driver (see nmdm(4))
1361 # Notes on the Comtrol Rocketport driver:
1363 # The exact values used for rp0 depend on how many boards you have
1364 # in the system. The manufacturer's sample configs are listed as:
1366 # Comtrol Rocketport ISA single card
1367 # device rp0 at isa? port 0x280
1369 # If instead you have two ISA cards, one installed at 0x100 and the
1370 # second installed at 0x180, then you should add the following to
1371 # your kernel configuration file:
1373 # device rp0 at isa? port 0x100
1374 # device rp1 at isa? port 0x180
1376 # For 4 ISA cards, it might be something like this:
1378 # device rp0 at isa? port 0x180
1379 # device rp1 at isa? port 0x100
1380 # device rp2 at isa? port 0x340
1381 # device rp3 at isa? port 0x240
1383 # And for PCI cards, you only need say:
1387 # Notes on the Specialix SI/XIO driver:
1388 # **This is NOT a Specialix supported Driver!**
1389 # The host card is memory, not IO mapped.
1390 # The Rev 1 host cards use a 64K chunk, on a 32K boundary.
1391 # The Rev 2 host cards use a 32K chunk, on a 32K boundary.
1392 # The cards can use an IRQ of 11, 12 or 15.
1394 # for the SoundBlaster 16 multicd - up to 4 devices
1395 device joy0 at isa? port IO_GAME
1397 #device rp0 at isa? port 0x280
1398 device si0 at isa? iomem 0xd0000 irq 12
1399 # nullmodem terminal driver
1402 # The `ahc' device provides support for the Adaptec 274X and 284X
1406 # The aic7xxx driver will attempt to use memory mapped I/O for all PCI
1407 # controllers that have it configured only if this option is set. Unfortunately,
1408 # this doesn't work on some motherboards, which prevents it from being the
1410 options AHC_ALLOW_MEMIO
1412 # The adw driver will attempt to use memory mapped I/O for all PCI
1413 # controllers that have it configured only if this option is set.
1414 options ADW_ALLOW_MEMIO
1417 # PCI devices & PCI options:
1419 # The main PCI bus device is `pci'. It provides auto-detection and
1420 # configuration support for all devices on the PCI bus, using either
1421 # configuration mode defined in the PCI specification.
1427 #Enable pci resources left off by a "lazy" BIOS.
1429 options COMPAT_OLDPCI #FreeBSD 2.2 and 3.x compatibility shims
1436 # The `ahc' device provides support for the Adaptec 29/3940(U)(W)
1437 # and motherboard based AIC7870/AIC7880 adapters.
1439 options AHC_DEBUG_OPTS=0xffffffff
1440 options AHC_REG_PRETTY_PRINT
1441 options AHC_TMODE_ENABLE
1443 # The 'ahd' device provides support for the Adaptec 79xx Ultra320
1444 # SCSI adapters. Options are documented in the ahd(4) manpage:
1446 options AHD_DEBUG_OPTS=0xffffffff
1447 options AHD_REG_PRETTY_PRINT
1448 #options AHD_TMODE_ENABLE=0xff
1450 # The `amd' device provides support for the AMD 53C974 SCSI host
1451 # adapter chip as found on devices such as the Tekram DC-390(T).
1453 # The `bge' device provides support for gigabit ethernet adapters
1454 # based on the Broadcom BCM570x family of controllers, including the
1455 # 3Com 3c996-T, the Netgear GA302T, the SysKonnect SK-9D21 and SK-9D41,
1456 # and the embedded gigE NICs on Dell PowerEdge 2550 servers.
1458 # The `ncr' device provides support for the NCR 53C810 and 53C825
1459 # self-contained SCSI host adapters.
1461 # The `isp' device provides support for the Qlogic ISP 1020, 1040
1462 # nd 1040B PCI SCSI host adapters, ISP 1240 Dual Ultra SCSI,
1463 # ISP 1080 and 1280 (Dual) Ultra2, ISP 12160 Ultra3 SCSI, as well as
1464 # the Qlogic ISP 2100 and ISP 2200 Fibre Channel Host Adapters.
1466 # The `dc' device provides support for PCI fast ethernet adapters
1467 # based on the DEC/Intel 21143 and various workalikes including:
1468 # the ADMtek AL981 Comet and AN985 Centaur, the ASIX Electronics
1469 # AX88140A and AX88141, the Davicom DM9100 and DM9102, the Lite-On
1470 # 82c168 and 82c169 PNIC, the Lite-On/Macronix LC82C115 PNIC II
1471 # and the Macronix 98713/98713A/98715/98715A/98725 PMAC. This driver
1472 # replaces the old al, ax, dm, pn and mx drivers. List of brands:
1473 # Digital DE500-BA, Kingston KNE100TX, D-Link DFE-570TX, SOHOware SFA110,
1474 # SVEC PN102-TX, CNet Pro110B, 120A, and 120B, Compex RL100-TX,
1475 # LinkSys LNE100TX, LNE100TX V2.0, Jaton XpressNet, Alfa Inc GFC2204,
1478 # The `de' device provides support for the Digital Equipment DC21040
1479 # self-contained Ethernet adapter.
1481 # The `em' device provides support for the Intel Pro/1000 Family of Gigabit
1482 # adapters (82542, 82543, 82544, 82540).
1484 # The `et' device provides support for the Agere ET1310 10/100/1000 PCIe
1487 # The `fxp' device provides support for the Intel EtherExpress Pro/100B
1488 # PCI Fast Ethernet adapters.
1490 # The 'lge' device provides support for PCI gigabit ethernet adapters
1491 # based on the Level 1 LXT1001 NetCellerator chipset. This includes the
1492 # D-Link DGE-500SX, SMC TigerCard 1000 (SMC9462SX), and some Addtron cards.
1494 # The 'my' device provides support for the Myson MTD80X and MTD89X PCI
1495 # Fast Ethernet adapters.
1497 # The 'nge' device provides support for PCI gigabit ethernet adapters
1498 # based on the National Semiconductor DP83820 and DP83821 chipset. This
1499 # includes the SMC EZ Card 1000 (SMC9462TX), D-Link DGE-500T, Asante
1500 # FriendlyNet GigaNIX 1000TA and 1000TPC, the Addtron AEG320T, the
1501 # LinkSys EG1032 and EG1064, the Surecom EP-320G-TX and the Netgear GA622T.
1503 # The 'pcn' device provides support for PCI fast ethernet adapters based
1504 # on the AMD Am79c97x chipsets, including the PCnet/FAST, PCnet/FAST+,
1505 # PCnet/PRO and PCnet/Home. These were previously handled by the lnc
1506 # driver (and still will be if you leave this driver out of the kernel).
1508 # Te 're' device provides support for PCI GigaBit ethernet adapters based
1509 # on the RealTek 8169 chipset. It also supports the 8139C+ and is the
1510 # preferred driver for that chip.
1512 # The 'rl' device provides support for PCI fast ethernet adapters based
1513 # on the RealTek 8129/8139 chipset. Note that the RealTek driver defaults
1514 # to using programmed I/O to do register accesses because memory mapped
1515 # mode seems to cause severe lockups on SMP hardware. This driver also
1516 # supports the Accton EN1207D `Cheetah' adapter, which uses a chip called
1517 # the MPX 5030/5038, which is either a RealTek in disguise or a RealTek
1518 # workalike. Note that the D-Link DFE-530TX+ uses the RealTek chipset
1519 # and is supported by this driver, not the 'vr' driver.
1521 # The 'sf' device provides support for Adaptec Duralink PCI fast
1522 # ethernet adapters based on the Adaptec AIC-6915 "starfire" controller.
1523 # This includes dual and quad port cards, as well as one 100baseFX card.
1524 # Most of these are 64-bit PCI devices, except for one single port
1525 # card which is 32-bit.
1527 # The 'ste' device provides support for adapters based on the Sundance
1528 # Technologies ST201 PCI fast ethernet controller. This includes the
1531 # The 'sis' device provides support for adapters based on the Silicon
1532 # Integrated Systems SiS 900 and SiS 7016 PCI fast ethernet controller
1535 # The 'sk' device provides support for the SysKonnect SK-984x series
1536 # PCI gigabit ethernet NICs. This includes the SK-9841 and SK-9842
1537 # single port cards (single mode and multimode fiber) and the
1538 # SK-9843 and SK-9844 dual port cards (also single mode and multimode).
1539 # The driver will autodetect the number of ports on the card and
1540 # attach each one as a separate network interface.
1542 # The 'ti' device provides support for PCI gigabit ethernet NICs based
1543 # on the Alteon Networks Tigon 1 and Tigon 2 chipsets. This includes the
1544 # Alteon AceNIC, the 3Com 3c985, the Netgear GA620 and various others.
1545 # Note that you will probably want to bump up NMBCLUSTERS a lot to use
1548 # The 'tl' device provides support for the Texas Instruments TNETE100
1549 # series 'ThunderLAN' cards and integrated ethernet controllers. This
1550 # includes several Compaq Netelligent 10/100 cards and the built-in
1551 # ethernet controllers in several Compaq Prosignia, Proliant and
1552 # Deskpro systems. It also supports several Olicom 10Mbps and 10/100
1555 # The `tx' device provides support for the SMC 9432 TX, BTX and FTX cards.
1557 # The `txp' device provides support for the 3Com 3cR990 "Typhoon"
1560 # The `vr' device provides support for various fast ethernet adapters
1561 # based on the VIA Technologies VT3043 `Rhine I' and VT86C100A `Rhine II'
1562 # chips, including the D-Link DFE530TX (see 'rl' for DFE530TX+), the Hawking
1563 # Technologies PN102TX, and the AOpen/Acer ALN-320.
1565 # The `vx' device provides support for the 3Com 3C590 and 3C595
1568 # The `wb' device provides support for various fast ethernet adapters
1569 # based on the Winbond W89C840F chip. Note: this is not the same as
1570 # the Winbond W89C940F, which is an NE2000 clone.
1572 # The `xl' device provides support for the 3Com 3c900, 3c905 and
1573 # 3c905B (Fast) Etherlink XL cards and integrated controllers. This
1574 # includes the integrated 3c905B-TX chips in certain Dell Optiplex and
1575 # Dell Precision desktop machines and the integrated 3c905-TX chips
1576 # in Dell Latitude laptop docking stations.
1578 # The 'bktr' device is a PCI video capture device using the Brooktree
1579 # bt848/bt848a/bt849a/bt878/bt879 chipset. When used with a TV Tuner it forms a
1580 # TV card, eg Miro PC/TV, Hauppauge WinCast/TV WinTV, VideoLogic Captivator,
1581 # Intel Smart Video III, AverMedia, IMS Turbo, FlyVideo.
1583 # options OVERRIDE_CARD=xxx
1584 # options OVERRIDE_TUNER=xxx
1585 # options OVERRIDE_MSP=1
1586 # options OVERRIDE_DBX=1
1587 # These options can be used to override the auto detection
1588 # The current values for xxx are found in src/sys/dev/video/bktr/bktr_card.h
1589 # Using sysctl(8) run-time overrides on a per-card basis can be made
1591 # options BKTR_SYSTEM_DEFAULT=BROOKTREE_PAL
1593 # options BKTR_SYSTEM_DEFAULT=BROOKTREE_NTSC
1594 # Specifes the default video capture mode.
1595 # This is required for Dual Crystal (28&35Mhz) boards where PAL is used
1596 # to prevent hangs during initialisation. eg VideoLogic Captivator PCI.
1598 # options BKTR_USE_PLL
1599 # PAL or SECAM users who have a 28Mhz crystal (and no 35Mhz crystal)
1600 # must enable PLL mode with this option. eg some new Bt878 cards.
1602 # options BKTR_GPIO_ACCESS
1603 # This enable IOCTLs which give user level access to the GPIO port.
1605 # options BKTR_NO_MSP_RESET
1606 # Prevents the MSP34xx reset. Good if you initialise the MSP in another OS first
1608 # options BKTR_430_FX_MODE
1609 # Switch Bt878/879 cards into Intel 430FX chipset compatibility mode.
1611 # options BKTR_SIS_VIA_MODE
1612 # Switch Bt878/879 cards into SIS/VIA chipset compatibility mode which is
1613 # needed for some old SiS and VIA chipset motherboards.
1614 # This also allows Bt878/879 chips to work on old OPTi (<1997) chipset
1615 # motherboards and motherboards with bad or incomplete PCI 2.1 support.
1616 # As a rough guess, old = before 1998
1618 # options BKTR_NEW_MSP34XX_DRIVER
1619 # Use new, more complete initialization scheme for the msp34* soundchip.
1620 # Should fix stereo autodetection if the old driver does only output
1623 # options BKTR_OVERRIDE_CARD=xxx
1624 # options BKTR_OVERRIDE_DBX=xxx
1625 # options BKTR_OVERRIDE_MSP=xxx
1626 # options BKTR_OVERRIDE_TUNER=xxx
1627 # These options can be used to select a specific device, regardless of
1628 # the autodetection and i2c device checks (see comments in bktr_card.c).
1630 device ahc # AHA2940 and onboard AIC7xxx devices
1631 device ahd # AIC79xx devices
1632 device amd # AMD 53C974 (Tekram DC-390(T))
1633 device isp # Qlogic family
1634 device ispfw # Firmware for QLogic HBAs
1635 device mpt # LSI '909 FC adapters
1636 device mps # LSI-Logic MPT-Fusion 2
1637 device ncr # NCR/Symbios Logic
1638 device sym # NCR/Symbios Logic (newer chipsets)
1639 device trm # Tekram DC395U/UW/F and DC315U
1643 # ISP_TARGET_MODE - enable target mode operation
1644 #options ISP_TARGET_MODE=1
1646 # Options used in dev/sym/ (Symbios SCSI driver).
1647 #options SYM_SETUP_LP_PROBE_MAP #-Low Priority Probe Map (bits)
1648 # Allows the ncr to take precedence
1649 # 1 (1<<0) -> 810a, 860
1650 # 2 (1<<1) -> 825a, 875, 885, 895
1651 # 4 (1<<2) -> 895a, 896, 1510d
1652 #options SYM_SETUP_SCSI_DIFF #-HVD support for 825a, 875, 885
1653 # disabled:0 (default), enabled:1
1654 #options SYM_SETUP_PCI_PARITY #-PCI parity checking
1655 # disabled:0, enabled:1 (default)
1656 #options SYM_SETUP_MAX_LUN #-Number of LUNs supported
1657 # default:8, range:[1..64]
1660 # MII bus support is required for some PCI 10/100 ethernet NICs,
1661 # namely those which use MII-compliant transceivers or implement
1662 # transceiver control interfaces that operate like an MII. Adding
1663 # "device miibus0" to the kernel config pulls in support for
1664 # the generic miibus API and all of the PHY drivers, including a
1665 # generic one for PHYs that aren't specifically handled by an
1666 # individual driver.
1669 # PCI Ethernet NICs that use the common MII bus controller code.
1670 device ae # Attansic/Atheros L2 Fast Ethernet
1671 device alc # Atheros AR8131/AR8132
1672 device ale # Atheros AR8121/AR8113/AR8114
1673 device age # Attansic/Atheros L1 Gigabit Ethernet
1674 device bce # Broadcom NetXtreme II Gigabit Ethernet
1675 device bfe # Broadcom BCM440x 10/100 Ethernet
1676 device dc # DEC/Intel 21143 and various workalikes
1677 device fxp # Intel EtherExpress PRO/100B (82557, 82558)
1678 device my # Myson Fast Ethernet (MTD80X, MTD89X)
1679 device pcn # AMD Am79C97x PCI 10/100 NICs
1680 device re # RealTek 8139C+/8169
1681 device rl # RealTek 8129/8139
1682 device sbsh # Granch SBNI16 SHDSL modem
1683 device sf # Adaptec AIC-6915 (``Starfire'')
1684 device sis # Silicon Integrated Systems SiS 900/SiS 7016
1685 device ste # Sundance ST201 (D-Link DFE-550TX)
1686 device tl # Texas Instruments ThunderLAN
1687 device tx # SMC EtherPower II (83c17x ``EPIC'')
1688 device vge # VIA 612x GigE
1689 device vr # VIA Rhine, Rhine II
1690 device wb # Winbond W89C840F
1691 device xl # 3Com 3c90x (``Boomerang'', ``Cyclone'')
1693 # PCI Ethernet NICs.
1694 device de # DEC/Intel DC21x4x (``Tulip'')
1695 device txp # 3Com 3cR990 (``Typhoon'')
1696 device vx # 3Com 3c590, 3c595 (``Vortex'')
1698 # Gigabit Ethernet NICs.
1699 device bge # Broadcom BCM570x (``Tigon III'')
1700 device em # Intel Pro/1000 (8254x,8257x)
1702 device emx # Intel Pro/1000 (8257{1,2,3,4})
1704 device ig_hal # Intel Pro/1000 hardware abstraction layer
1705 device et # Agere ET1310 10/100/1000 Ethernet
1706 device lge # Level 1 LXT1001 (``Mercury'')
1707 device mxge # Myricom Myri-10G 10GbE NIC
1708 device nfe # nVidia nForce2/3 MCP04/51/55 CK804
1709 device nge # NatSemi DP83820 and DP83821
1710 device sk # SysKonnect GEnesis, LinkSys EG1023, D-Link
1711 device ti # Alteon (``Tigon I'', ``Tigon II'')
1712 device stge # Sundance/Tamarack TC9021 Gigabit Ethernet
1713 device msk # Marvell/SysKonnect Yukon II Gigabit Ethernet
1714 device jme # JMicron Gigabit/Fast Ethernet
1716 # Brooktree driver has been ported to the new I2C framework. Thus,
1717 # you'll need to have the following 3 lines in the kernel config.
1721 # The iic and smb devices are only needed if you want to control other
1722 # I2C slaves connected to the external connector of some cards.
1725 options BKTR_NEW_MSP34XX_DRIVER
1727 # WinTV PVR-250/350 driver
1733 # pccard: pccard slots
1734 # cardbus/cbb: cardbus bridge
1739 # For older notebooks that signal a powerfail condition (external
1740 # power supply dropped, or battery state low) by issuing an NMI:
1742 options POWERFAIL_NMI # make it beep instead of panicing
1748 # mmcsd MMC/SD memory card
1749 # sdhci Generic PCI SD Host Controller
1758 # System Management Bus support is provided by the 'smbus' device.
1759 # Access to the SMBus device is via the 'smb' device (/dev/smb*),
1760 # which is a child of the 'smbus' device.
1762 # Supported devices:
1763 # smb standard io through /dev/smb*
1765 # Supported SMB interfaces:
1766 # iicsmb I2C to SMB bridge with any iicbus interface
1767 # bktr brooktree848 I2C hardware interface
1768 # intpm Intel PIIX4 (82371AB, 82443MX) Power Management Unit
1769 # alpm Acer Aladdin-IV/V/Pro2 Power Management Unit
1770 # ichsmb Intel ICH SMBus controller chips (82801AA, 82801AB, 82801BA)
1771 # viapm VIA VT82C586B,596,686A and VT8233 SMBus controllers
1772 # amdpm AMD 756 Power Management Unit
1773 # amdsmb AMD 8111 SMBus 2.0 Controller
1775 device smbus # Bus support, required for smb below.
1789 # Philips i2c bus support is provided by the `iicbus' device.
1791 # Supported devices:
1792 # ic i2c network interface
1793 # iic i2c standard io
1794 # iicsmb i2c to smb bridge. Allow i2c i/o with smb commands.
1796 # Supported interfaces:
1797 # pcf Philips PCF8584 ISA-bus controller
1798 # bktr brooktree848 I2C software interface
1801 # iicbb generic I2C bit-banging code (needed by lpbb, bktr)
1803 device iicbus # Bus support, required for ic/iic/iicsmb below.
1808 device iicsmb # smb over i2c bridge
1810 device pcf0 at isa? port 0x320 irq 5
1812 # Intel Core and newer CPUs on-die digital thermal sensor support
1815 # AMD Family 0Fh, 10h and 11h temperature sensors
1819 # ThinkPad Active Protection System accelerometer
1820 device aps0 at isa? port 0x1600
1822 # HW monitoring devices lm(4), it(4) and nsclpcsio.
1823 device lm0 at isa? port 0x290
1824 device it0 at isa? port 0x290
1825 device it1 at isa? port 0xc00
1826 device it2 at isa? port 0xd00
1827 device it3 at isa? port 0x228
1828 device nsclpcsio0 at isa? port 0x2e
1829 device nsclpcsio1 at isa? port 0x4e
1830 device wbsio0 at isa? port 0x2e
1831 device wbsio1 at isa? port 0x4e
1832 device lm#3 at wbsio?
1833 device uguru0 at isa? port 0xe0 # ABIT uGuru
1835 #---------------------------------------------------------------------------
1838 # See /usr/share/examples/isdn/ROADMAP for an introduction to isdn4bsd.
1840 # i4b passive ISDN cards support contains the following hardware drivers:
1842 # isic - Siemens/Infineon ISDN ISAC/HSCX/IPAC chipset driver
1843 # iwic - Winbond W6692 PCI bus ISDN S/T interface controller
1844 # ifpi - AVM Fritz!Card PCI driver
1845 # ifpi2 - AVM Fritz!Card PCI driver Version 2
1846 # ihfc - Cologne Chip HFC ISA/ISA-PnP chipset driver
1847 # ifpnp - AVM Fritz!Card PnP driver
1848 # itjc - Siemens ISAC / TJNet Tiger300/320 chipset
1850 # i4b active ISDN cards support contains the following hardware drivers:
1852 # iavc - AVM B1 PCI, AVM B1 ISA, AVM T1
1854 # Note that the ``options'' (if given) and ``device'' lines must BOTH
1855 # be uncommented to enable support for a given card !
1857 # In addition to a hardware driver (and probably an option) the mandatory
1858 # ISDN protocol stack devices and the mandatory support device must be
1859 # enabled as well as one or more devices from the optional devices section.
1861 #---------------------------------------------------------------------------
1862 # isic driver (Siemens/Infineon chipsets)
1863 #---------------------------------------------------------------------------
1865 # ISA bus non-PnP Cards:
1866 # ----------------------
1868 # Teles S0/8 or Niccy 1008
1870 #device isic0 at isa? iomem 0xd0000 irq 5 flags 1
1872 # Teles S0/16 or Creatix ISDN-S0 or Niccy 1016
1874 #device isic0 at isa? port 0xd80 iomem 0xd0000 irq 5 flags 2
1877 #options TEL_S0_16_3
1878 #device isic0 at isa? port 0xd80 irq 5 flags 3
1880 # AVM A1 or AVM Fritz!Card
1882 #device isic0 at isa? port 0x340 irq 5 flags 4
1884 # USRobotics Sportster ISDN TA intern
1886 #device isic0 at isa? port 0x268 irq 5 flags 7
1888 # ITK ix1 Micro ( < V.3, non-PnP version )
1890 #device isic0 at isa? port 0x398 irq 10 flags 18
1894 #device isic0 at isa? port 0x360 irq 10 flags 20
1896 # ISA bus PnP Cards:
1897 # ------------------
1900 #options TEL_S0_16_3_P
1903 # Creatix ISDN-S0 P&P
1907 # Dr. Neuhaus Niccy Go@
1911 # Sedlbauer Win Speed
1919 # ELSA QuickStep 1000pro ISA
1920 #options ELSA_QS1ISA
1923 # ITK ix1 Micro ( V.3, PnP version )
1927 # Siemens I-Surf 2.0
1928 #options SIEMENS_ISURF2
1931 # Asuscom ISDNlink 128K ISAC
1932 #options ASUSCOM_IPAC
1935 # Eicon Diehl DIVA 2.0 and 2.02
1939 # Compaq Microcom 610
1940 #options COMPAQ_M610
1946 # ELSA MicroLink ISDN/PCI (same as ELSA QuickStep 1000pro PCI)
1947 #options ELSA_QS1PCI
1950 #---------------------------------------------------------------------------
1951 # ifpnp driver for AVM Fritz!Card ISA PnP
1952 #---------------------------------------------------------------------------
1954 # AVM Fritz!Card ISA PnP
1957 #---------------------------------------------------------------------------
1958 # ihfc driver for Cologne Chip ISA chipsets (experimental!)
1959 #---------------------------------------------------------------------------
1961 # Teles 16.3c ISA PnP
1962 # AcerISDN P10 ISA PnP
1963 # TELEINT ISDN SPEED No.1
1966 #---------------------------------------------------------------------------
1967 # ifpi driver for AVM Fritz!Card PCI 1.0 (2.0 unsupported!)
1968 #---------------------------------------------------------------------------
1970 # AVM Fritz!Card PCI 1.0
1973 #---------------------------------------------------------------------------
1974 # ifpi2 driver for AVM Fritz!Card PCI 2.0
1975 #---------------------------------------------------------------------------
1977 # AVM Fritz!Card PCI 2.0
1980 #---------------------------------------------------------------------------
1981 # iwic driver for Winbond W6692 chipset
1982 #---------------------------------------------------------------------------
1984 # ASUSCOM P-IN100-ST-D (and other Winbond W6692 based cards)
1987 #---------------------------------------------------------------------------
1988 # itjc driver for Siemens ISAC / TJNet Tiger300/320 chipset
1989 #---------------------------------------------------------------------------
1991 # Traverse Technologies NETjet-S
1995 #---------------------------------------------------------------------------
1996 # iavc driver (AVM active cards, needs i4bcapi driver!)
1997 #---------------------------------------------------------------------------
1999 #pseudo-device "i4bcapi" 2
2004 # AVM B1 ISA bus (PnP mode not supported!)
2005 #device iavc0 at isa? port 0x150 irq 5
2008 # ISDN Protocol Stack (mandatory)
2009 # -------------------------------
2011 # Q.921 / layer 2 - i4b passive cards D channel handling
2012 #pseudo-device "i4bq921"
2014 # Q.931 / layer 3 - i4b passive cards D channel handling
2015 #pseudo-device "i4bq931"
2017 # layer 4 - i4b common passive and active card handling
2018 #pseudo-device "i4b"
2023 # userland driver to do ISDN tracing (for passive cards only)
2024 #pseudo-device "i4btrc" 4
2026 # userland driver to control the whole thing (mandatory)
2027 #pseudo-device "i4bctl"
2029 # userland driver for access to raw B channel
2030 #pseudo-device "i4brbch" 4
2032 # userland driver for telephony
2033 #pseudo-device "i4btel" 2
2035 # network driver for IP over raw HDLC ISDN
2036 #pseudo-device "i4bipr" 4
2037 # enable VJ header compression detection for ipr i/f
2039 # enable logging of the first n IP packets to isdnd (n=32 here)
2042 # network driver for sync PPP over ISDN - requires sppp
2043 #pseudo-device "i4bisppp" 4
2048 # Parallel port bus support is provided by the `ppbus' device.
2049 # Multiple devices may be attached to the parallel port, devices
2050 # are automatically probed and attached when found.
2052 # Supported devices:
2053 # vpo Iomega Zip Drive
2054 # Requires SCSI disk support ('scbus' and 'da'); the best
2055 # performance is achieved with ports in EPP 1.9 mode.
2056 # lpt Parallel Printer
2057 # plip Parallel network interface
2058 # ppi General-purpose I/O ("Geek Port") + IEEE1284 I/O
2059 # pps Pulse per second Timing Interface
2060 # lpbb Philips official parallel port I2C bit-banging interface
2062 # Supported interfaces:
2063 # ppc ISA-bus parallel port interfaces.
2066 options PPC_PROBE_CHIPSET # Enable chipset specific detection
2067 # (see flags in ppc(4))
2068 options DEBUG_1284 # IEEE1284 signaling protocol debug
2069 options PERIPH_1284 # Makes your computer act as a IEEE1284
2070 # compliant peripheral
2071 options DONTPROBE_1284 # Avoid boot detection of PnP parallel devices
2072 options VP0_DEBUG # ZIP/ZIP+ debug
2073 options LPT_DEBUG # Printer driver debug
2074 options PPC_DEBUG=2 # Parallel chipset level debug
2075 options PLIP_DEBUG # Parallel network IP interface debug
2076 options PCFCLOCK_VERBOSE # Verbose pcfclock driver
2077 options PCFCLOCK_MAX_RETRIES=5 # Maximum read tries (default 10)
2079 device ppc0 at isa? irq 7
2089 # Kernel BOOTP support
2091 options BOOTP # Use BOOTP to obtain IP address/hostname
2092 options BOOTP_NFSROOT # NFS mount root filesystem using BOOTP info
2093 options BOOTP_NFSV3 # Use NFS v3 to NFS mount root
2094 options BOOTP_COMPAT # Workaround for broken bootp daemons.
2095 options BOOTP_WIRED_TO=fxp0 # Use interface fxp0 for BOOTP
2098 # Add tie-ins for a hardware watchdog. This only enable the hooks;
2099 # the user must still supply the actual driver.
2104 # Set the number of PV entries per process. Increasing this can
2105 # stop panics related to heavy use of shared memory. However, that can
2106 # (combined with large amounts of physical memory) cause panics at
2107 # boot time due the kernel running out of VM space.
2109 # If you're tweaking this, you might also want to increase the sysctls
2110 # "vm.v_free_min", "vm.v_free_reserved", and "vm.v_free_target".
2112 # The value below is the one more than the default.
2114 options PMAP_SHPGPERPROC=201
2117 # Disable swapping. This option removes all code which actually performs
2118 # swapping, so it's not possible to turn it back on at run-time.
2120 # This is sometimes usable for systems which don't have any swap space
2121 # (see also sysctls "vm.defer_swapspace_pageouts" and
2122 # "vm.disable_swapspace_pageouts")
2124 #options NO_SWAPPING
2126 # Set the size of the buffer cache KVM reservation, in buffers. This is
2127 # scaled by approximately 16384 bytes. The system will auto-size the buffer
2128 # cache if this option is not specified.
2132 # Set the size of the mbuf KVM reservation, in clusters. This is scaled
2133 # by approximately 2048 bytes. The system will auto-size the mbuf area
2134 # to (512 + maxusers*16) if this option is not specified.
2135 # maxusers is in turn computed at boot time depending on available memory
2136 # or set to the value specified by "options MAXUSERS=x" (x=0 means
2138 # So, to take advantage of autoscaling, you have to remove both
2139 # NMBCLUSTERS and MAXUSERS (and NMBUFS) from your kernel config.
2141 options NMBCLUSTERS=1024
2143 # Set the number of mbufs available in the system. Each mbuf
2144 # consumes 256 bytes. The system will autosize this (to 4 times
2145 # the number of NMBCLUSTERS, depending on other constraints)
2146 # if this option is not specified.
2150 # Tune the buffer cache maximum KVA reservation, in bytes. The maximum is
2151 # usually capped at 200 MB, effecting machines with > 1GB of ram. Note
2152 # that the buffer cache only really governs write buffering and disk block
2153 # translations. The VM page cache is our primary disk cache and is not
2154 # effected by the size of the buffer cache.
2156 options VM_BCACHE_SIZE_MAX="(100*1024*1024)"
2158 # Tune the swap zone KVA reservation, in bytes. The default is typically
2159 # 70 MB, giving the system the ability to manage a maximum of 28GB worth
2160 # of swapped out data.
2162 options VM_SWZONE_SIZE_MAX="(50*1024*1024)"
2165 # Enable extra debugging code for locks. This stores the filename and
2166 # line of whatever acquired the lock in the lock itself, and change a
2167 # number of function calls to pass around the relevant data. This is
2168 # not at all useful unless you are debugging lock code. Also note
2169 # that it is likely to break e.g. fstat(1) unless you recompile your
2170 # userland with -DDEBUG_LOCKS as well.
2174 # Set the amount of time (in seconds) the system will wait before
2175 # rebooting automatically when a kernel panic occurs. If set to (-1),
2176 # the system will wait indefinitely until a key is pressed on the
2178 options PANIC_REBOOT_WAIT_TIME=16
2180 # Attempt to bypass the buffer cache and put data directly into the
2181 # userland buffer for read operation when O_DIRECT flag is set on the
2182 # file. Both offset and length of the read operation must be
2183 # multiples of the physical media sector size.
2187 # Specify a lower limit for the number of swap I/O buffers. They are
2188 # (among other things) used when bypassing the buffer cache due to
2189 # DIRECTIO kernel option enabled and O_DIRECT flag set on file.
2191 #options NSWBUF_MIN=120
2193 # The 'asr' driver provides support for current DPT/Adaptec SCSI RAID
2194 # controllers (SmartRAID V and VI and later).
2195 # These controllers require the CAM infrastructure.
2199 # The 'dpt' driver provides support for DPT controllers (http://www.dpt.com/).
2200 # These have hardware RAID-{0,1,5} support, and do multi-initiator I/O.
2201 # The DPT controllers are commonly re-licensed under other brand-names -
2202 # some controllers by Olivetti, Dec, HP, AT&T, SNI, AST, Alphatronic, NEC and
2203 # Compaq are actually DPT controllers.
2205 # See src/sys/dev/raid/dpt for debugging and other subtle options.
2206 # DPT_MEASURE_PERFORMANCE Enables a set of (semi)invasive metrics. Various
2207 # instruments are enabled. The tools in
2208 # /usr/sbin/dpt_* assume these to be enabled.
2209 # DPT_HANDLE_TIMEOUTS Normally device timeouts are handled by the DPT.
2210 # If you ant the driver to handle timeouts, enable
2211 # this option. If your system is very busy, this
2212 # option will create more trouble than solve.
2213 # DPT_TIMEOUT_FACTOR Used to compute the excessive amount of time to
2214 # wait when timing out with the above option.
2215 # DPT_DEBUG_xxxx These are controllable from sys/dev/dpt/raid/dpt.h
2216 # DPT_LOST_IRQ When enabled, will try, once per second, to catch
2217 # any interrupt that got lost. Seems to help in some
2218 # DPT-firmware/Motherboard combinations. Minimal
2219 # cost, great benefit.
2220 # DPT_RESET_HBA Make "reset" actually reset the controller
2221 # instead of fudging it. Only enable this if you
2222 # are 100% certain you need it.
2227 #!CAM# options DPT_MEASURE_PERFORMANCE
2228 #!CAM# options DPT_HANDLE_TIMEOUTS
2229 options DPT_TIMEOUT_FACTOR=4
2230 options DPT_LOST_IRQ
2231 options DPT_RESET_HBA
2234 # Compaq "CISS" RAID controllers (SmartRAID 5* series)
2235 # These controllers have a SCSI-like interface, and require the
2236 # CAM infrastructure.
2241 # Intel Integrated RAID controllers.
2242 # This driver is supported and maintained by
2243 # "Leubner, Achim" <Achim_Leubner@adaptec.com>.
2248 # Mylex AcceleRAID and eXtremeRAID controllers with v6 and later
2249 # firmware. These controllers have a SCSI-like interface, and require
2250 # the CAM infrastructure.
2261 # General USB code (mandatory for USB)
2268 # Generic USB device driver
2270 # Human Interface Device (anything with buttons and dials)
2276 # USB Iomega Zip 100 Drive (Requires scbus and da)
2282 # USB Rio (MP3 Player)
2302 # ADMtek USB ethernet. Supports the LinkSys USB100TX,
2303 # the Billionton USB100, the Melco LU-ATX, the D-Link DSB-650TX
2304 # and the SMC 2202USB. Also works with the ADMtek AN986 Pegasus
2308 # ASIX Electronics AX88172 USB 2.0 ethernet driver. Used in the
2309 # LinkSys USB200M and various other adapters.
2312 # CATC USB-EL1201A USB ethernet. Supports the CATC Netmate
2313 # and Netmate II, and the Belkin F5U111.
2316 # Kawasaki LSI ethernet. Supports the LinkSys USB10T,
2317 # Entrega USB-NET-E45, Peracom Ethernet Adapter, the
2318 # 3Com 3c19250, the ADS Technologies USB-10BT, the ATen UC10T,
2319 # the Netgear EA101, the D-Link DSB-650, the SMC 2102USB
2320 # and 2104USB, and the Corega USB-T.
2323 # RealTek 8150 based USB ethernet device:
2325 # GREEN HOUSE GH-USB100B
2326 # Billionton ThumbLAN USBKR2-100B
2329 # USB wireless NICs, requires wlan_amrr
2331 # Ralink Technology RT2501USB/RT2601USB
2334 # Ralink Technology RT2500USB
2337 # debugging options for the USB subsystem
2342 options UKBD_DFLT_KEYMAP # specify the built-in keymap
2343 makeoptions UKBD_DFLT_KEYMAP=it.iso
2346 device firewire # Firewire bus code
2347 device sbp # SCSI over Firewire (Requires scbus and da)
2348 device fwe # Ethernet over Firewire (non-standard!)
2350 # dcons support (Dumb Console Device)
2351 device dcons # dumb console driver
2352 device dcons_crom # FireWire attachment
2353 options DCONS_BUF_SIZE=16384 # buffer size
2354 options DCONS_POLL_HZ=100 # polling rate
2355 options DCONS_FORCE_CONSOLE=1 # force to be the primary console
2356 options DCONS_FORCE_GDB=1 # force to be the gdb device
2358 #####################################################################
2361 # This is a port of the openbsd crypto framework. Include this when
2362 # configuring IPsec and when you have a h/w crypto device to accelerate
2363 # user applications that link to openssl.
2365 # Drivers are ports from openbsd with some simple enhancements that have
2366 # been fed back to openbsd (and hopefully will be included).
2368 pseudo-device crypto # core crypto support
2369 pseudo-device cryptodev # /dev/crypto for access to h/w
2371 device rndtest # FIPS 140-2 entropy tester
2373 device hifn # Hifn 7951, 7781, etc.
2374 options HIFN_DEBUG # enable debugging support: hw.hifn.debug
2375 #options HIFN_NO_RNG # for devices without RNG
2376 options HIFN_RNDTEST # enable rndtest support
2378 device ubsec # Broadcom 5501, 5601, 58xx
2379 options UBSEC_DEBUG # enable debugging support: hw.ubsec.debug
2380 #options UBSEC_NO_RNG # for devices without RNG
2381 options UBSEC_RNDTEST # enable rndtest support
2383 device aesni # hardware crypto/RNG for AES-NI
2384 device padlock # hardware crypto/RNG for VIA C3/C7/Eden
2387 # ACPI support using the Intel ACPI Component Architecture reference
2390 # ACPI_DEBUG enables the use of the debug.acpi.level and debug.acpi.layer
2391 # kernel environment variables to select initial debugging levels for the
2392 # Intel ACPICA code.
2394 # Note that building ACPI into the kernel is deprecated; the module is
2395 # normally loaded automatically by the loader.
2400 # ACPI Asus Extras (LCD backlight/brightness, video output, etc.)
2403 # ACPI Fujitsu Extras (Buttons)
2406 # ACPI extras driver for HP laptops
2409 # ACPI Panasonic Extras (LCD backlight/brightness, video output, etc.)
2410 device acpi_panasonic
2412 # ACPI Sony extra (LCD brightness)
2415 # ACPI extras driver for ThinkPad laptops
2416 device acpi_thinkpad
2418 # ACPI Toshiba Extras (LCD backlight/brightness, video output, etc.)
2421 # ACPI Video Extensions (LCD backlight/brightness, video output, etc.)
2424 device aibs # ASUSTeK AI Booster (ACPI ASOC ATK0110)
2427 # drm: General DRM code
2428 # i915drm: Intel i830, i845, i915, i945, i965, G33/35
2429 # mach64drm: ATI Mach64 cards - Rage and 3D Rage series
2430 # mgadrm: AGP Matrox G200, G400, G450, G550
2431 # r128drm: ATI Rage 128 cards
2432 # radeondrm: ATI Radeon cards
2433 # savagedrm: Savage cards
2435 # tdfxdrm: 3dfx Voodoo 3/4/5 and Banshee
2437 # DRM_DEBUG: include debug printfs, very slow
2439 # DRM requires AGP in the kernel.
2457 device cmx # Omnikey CardMan 4040 smartcard reader
2458 device gpio # Enable support for the gpio framework
2461 # Embedded system options:
2463 # An embedded system might want to run something other than init.
2464 options INIT_PATH="/sbin/init:/sbin/oinit"
2467 options BUS_DEBUG # enable newbus debugging
2468 options RSS_DEBUG # enable RSS (Receive Side Scaling) debugging
2470 # Record the program counter of the code interrupted by the statistics
2471 # clock interrupt. Use pctrack(8) to dump this information.
2472 options DEBUG_PCTRACK
2474 # More undocumented options for linting.
2475 # Note that documenting these are not considered an affront.
2477 #options ACPI_NO_SEMAPHORES
2478 options AHC_DUMP_EEPROM
2479 #options BKTR_ALLOC_PAGES=xxx
2480 options CAM_DEBUG_DELAY
2481 options CLUSTERDEBUG
2482 #options COMPAT_LINUX
2483 options COMPAT_SUNOS
2485 options DEBUG_CRIT_SECTIONS
2486 options DEBUG_INTERRUPTS
2487 #options DISABLE_PSE
2489 options EMX_RSS_DEBUG
2490 options JME_RSS_DEBUG
2491 #options ED_NO_MIIBUS
2492 options ENABLE_ALART
2494 options FB_INSTALL_CDEV
2495 #options I4B_SMP_WORKAROUND
2496 options I586_PMC_GUPROF=0x70000
2497 #options IEEE80211_DEBUG_REFCNT
2498 options IEEE80211_SUPPORT_SUPERG
2499 options KBDIO_DEBUG=10
2500 options KBD_MAXRETRY=4
2501 options KBD_MAXWAIT=6
2502 options KBD_RESETDELAY=201
2503 #options KERN_TIMESTAMP
2508 #options MAXFILES=xxx
2510 options NETATALKDEBUG
2514 options SCSI_NCR_DEBUG
2515 options SCSI_NCR_MAX_SYNC=10000
2516 options SCSI_NCR_MAX_WIDE=1
2517 options SCSI_NCR_MYADDR=7
2518 options SHOW_BUSYBUFS # List buffers that prevent root unmount
2521 options SLIP_IFF_OPTS
2522 options SOCKBUF_DEBUG
2523 options TDMA_BINTVAL_DEFAULT=5
2524 options TDMA_SLOTCNT_DEFAULT=2
2525 options TDMA_SLOTLEN_DEFAULT=10*1000
2526 options TDMA_TXRATE_11A_DEFAULT=2*24
2527 options TDMA_TXRATE_11B_DEFAULT=2*11
2528 options TDMA_TXRATE_11G_DEFAULT=2*24
2529 options TDMA_TXRATE_11NA_DEFAULT="(4|IEEE80211_RATE_MCS)"
2530 options TDMA_TXRATE_11NG_DEFAULT="(4|IEEE80211_RATE_MCS)"
2531 options TDMA_TXRATE_HALF_DEFAULT=2*12
2532 options TDMA_TXRATE_QUARTER_DEFAULT=2*6
2533 options TDMA_TXRATE_TURBO_DEFAULT=2*24
2534 #options TIMER_FREQ="((14318182+6)/12)"
2535 options VFS_BIO_DEBUG
2536 options VM_PAGE_DEBUG
2541 #options KTR_ETHERNET
2546 #options KTR_IF_START
2549 #options KTR_KERNENTRY
2551 #options KTR_POLLING
2552 #options KTR_SERIALIZER
2553 #options KTR_SPIN_CONTENTION
2554 #options KTR_TESTLOG
2556 #options KTR_USB_MEMORY
2558 options KTR_ENTRIES=1024
2559 options KTR_VERBOSE=1
2562 options ALTQ #alternate queueing
2563 options ALTQ_CBQ #class based queueing
2564 options ALTQ_RED #random early detection
2565 options ALTQ_RIO #triple red for diffserv (needs RED)
2566 options ALTQ_HFSC #hierarchical fair service curve
2567 options ALTQ_PRIQ #priority queue
2568 options ALTQ_FAIRQ #fair queue
2569 #options ALTQ_NOPCC #don't use processor cycle counter
2570 options ALTQ_DEBUG #for debugging
2571 # you might want to set kernel timer to 1kHz if you use CBQ,
2572 # especially with 100baseT
2578 options SCTP_USE_ADLER32
2579 options SCTP_HIGH_SPEED
2580 options SCTP_STAT_LOGGING
2581 options SCTP_CWND_LOGGING
2582 options SCTP_BLK_LOGGING
2583 options SCTP_STR_LOGGING
2584 options SCTP_FR_LOGGING
2585 options SCTP_MAP_LOGGING
2591 options WATCHDOG_ENABLE # Enable watchdog support framework
2592 options WDOG_DISABLE_ON_PANIC # Automatically disable watchdogs on panic
2595 options ERROR_LED_ON_PANIC # If an error led is present, light it up on panic