2 # LINT -- config file for checking all the sources, tries to pull in
3 # as much of the source tree as it can.
5 # $FreeBSD: src/sys/i386/conf/LINT,v 1.749.2.144 2003/06/04 17:56:59 sam Exp $
6 # $DragonFly: src/sys/config/LINT,v 1.117 2007/06/08 07:39:19 swildner Exp $
8 # NB: You probably don't want to try running a kernel built from this
9 # file. Instead, you should start from GENERIC, and add options from
10 # this file as required.
13 # These directives are mandatory. The machine directive specifies the
14 # platform and the machine_arch directive specifies the cpu architecture.
21 # This is the ``identification'' of the kernel. Usually this should
22 # be the same as the name of your kernel.
27 # The `maxusers' parameter controls the static sizing of a number of
28 # internal system tables by a formula defined in subr_param.c. Setting
29 # maxusers to 0 will cause the system to auto-size based on physical
35 # The `makeoptions' parameter allows variables to be passed to the
36 # generated Makefile in the build area.
38 # CONF_CFLAGS gives some extra compiler flags that are added to ${CFLAGS}
39 # after most other flags. Here we use it to inhibit use of non-optimal
40 # gcc builtin functions (e.g., memcmp).
42 # DEBUG happens to be magic.
43 # The following is equivalent to 'config -g KERNELNAME' and creates
44 # 'kernel.debug' compiled with -g debugging as well as a normal
45 # 'kernel'. Use 'make install.debug' to install the debug kernel
46 # but that isn't normally necessary as the debug symbols are not loaded
47 # by the kernel and are not useful there anyway.
49 # KERNEL can be overridden so that you can change the default name of your
52 # MODULES_OVERRIDE can be used to limit modules built to a specific list.
54 # INSTALLSTRIPPED can be set to cause installkernel to install stripped
55 # kernels and modules rather than a kernel and modules with debug symbols.
57 # INSTALLSTRIPPEDMODULES can be set to allow a full debug kernel to be
58 # installed, but to strip the installed modules.
60 makeoptions CONF_CFLAGS=-fno-builtin #Don't allow use of memcmp, etc.
61 #makeoptions DEBUG=-g #Build kernel with gdb(1) debug symbols
62 #makeoptions KERNEL=foo #Build kernel "foo" and install "/foo"
63 # Only build Linux API modules and plus those parts of the sound system I need.
64 #makeoptions MODULES_OVERRIDE="linux sound/snd sound/pcm sound/driver/maestro3"
65 #makeoptions INSTALLSTRIPPED=1
66 #makeoptions INSTALLSTRIPPEDMODULES=1
69 # Certain applications can grow to be larger than the 128M limit
70 # that FreeBSD initially imposes. Below are some options to
71 # allow that limit to grow to 256MB, and can be increased further
72 # with changing the parameters. MAXDSIZ is the maximum that the
73 # limit can be set to, and the DFLDSIZ is the default value for
74 # the limit. MAXSSIZ is the maximum that the stack limit can be
75 # set to. You might want to set the default lower than the max,
76 # and explicitly set the maximum with a shell command for processes
77 # that regularly exceed the limit like INND.
79 options MAXDSIZ="(256*1024*1024)"
80 options MAXSSIZ="(256*1024*1024)"
81 options DFLDSIZ="(256*1024*1024)"
84 # BLKDEV_IOSIZE sets the default block size used in user block
85 # device I/O. Note that this value will be overridden by the label
86 # when specifying a block device from a label with a non-0
87 # partition blocksize. The default is PAGE_SIZE.
89 options BLKDEV_IOSIZE=8192
91 # Options for the VM subsystem.
92 options PQ_CACHESIZE=512 # color for 512k/16k cache
94 # This allows you to actually store this configuration file into
95 # the kernel binary itself, where it may be later read by saying:
96 # strings -n 3 /kernel | sed -n 's/^___//p' > MYKERNEL
98 options INCLUDE_CONFIG_FILE # Include this file in kernel
101 # The root device and filesystem type can be compiled in;
102 # this provides a fallback option if the root device cannot
103 # be correctly guessed by the bootstrap code, or an override if
104 # the RB_DFLTROOT flag (-r) is specified when booting the kernel.
106 options ROOTDEVNAME=\"ufs:da0s2e\"
109 #####################################################################
112 # SMP enables building of a Symmetric MultiProcessor Kernel.
113 # APIC_IO enables the use of the IO APIC for Symmetric I/O.
117 # An SMP kernel will ONLY run on an Intel MP spec. qualified motherboard.
119 # Be sure to disable 'cpu I386_CPU' && 'cpu I486_CPU' for SMP kernels.
121 # Check the 'Rogue SMP hardware' section to see if additional options
122 # are required by your hardware.
126 options SMP # Symmetric MultiProcessor Kernel
127 options APIC_IO # Symmetric (APIC) I/O
130 # Rogue SMP hardware:
135 # The MP tables of most of the current generation MP motherboards
136 # do NOT properly support bridged PCI cards. To use one of these
137 # cards you should refer to ???
140 #####################################################################
144 # You must specify at least one CPU (the one you intend to run on);
145 # deleting the specification for CPUs you don't need to use may make
146 # parts of the system run faster. This is especially true removing
151 cpu I586_CPU # aka Pentium(tm)
152 cpu I686_CPU # aka Pentium Pro(tm)
155 # Options for CPU features.
157 # CPU_AMD64X2_INTR_SPAM tries to route HyperTransport EXTINT and NMI
158 # messages to LINT0 on the local APIC when the BIOS has forgotten to
159 # do that. If this is not done on a multi-core cpu, EXTINT and NMI
160 # get routed to the INTR/NMI pins on *BOTH* cores simultaneously, causing
161 # two INTA ack cycles one of which will almost certainly result in a
162 # spurious interrupt vector being presented. This is often visible as
163 # an unmaskable IRQ 7 which occurs for every normal interrupt that occurs
166 # CPU_ATHLON_SSE_HACK tries to enable SSE instructions when the BIOS has
167 # forgotten to enable them.
169 # CPU_BLUELIGHTNING_FPU_OP_CACHE enables FPU operand cache on IBM
170 # BlueLightning CPU. It works only with Cyrix FPU, and this option
171 # should not be used with Intel FPU.
173 # CPU_BLUELIGHTNING_3X enables triple-clock mode on IBM Blue Lightning
174 # CPU if CPU supports it. The default is double-clock mode on
175 # BlueLightning CPU box.
177 # CPU_BTB_EN enables branch target buffer on Cyrix 5x86 (NOTE 1).
179 # CPU_DIRECT_MAPPED_CACHE sets L1 cache of Cyrix 486DLC CPU in direct
180 # mapped mode. Default is 2-way set associative mode.
182 # CPU_CYRIX_NO_LOCK enables weak locking for the entire address space
183 # of Cyrix 6x86 and 6x86MX CPUs by setting the NO_LOCK bit of CCR1.
184 # Otherwise, the NO_LOCK bit of CCR1 is cleared. (NOTE 3)
186 # CPU_DISABLE_5X86_LSSER disables load store serialize (i.e. enables
187 # reorder). This option should not be used if you use memory mapped
190 # CPU_DISABLE_SSE disables SSE/MMX2 instructions support.
192 # CPU_ENABLE_TCC enables Thermal Control Circuitry (TCC) found in some
193 # Pentium(tm) 4 and (possibly) later CPUs. When enabled and detected,
194 # TCC supports restricting power consumption using the hw.p4tcc.*
195 # sysctls. This operates independently of SpeedStep and is useful on
196 # systems where other mechanisms such as apm(4) or acpi(4) don't work.
198 # CPU_ENABLE_EST enables support for Enhanced SpeedStep technology
199 # found in Pentium(tm) M processors.
201 # CPU_FASTER_5X86_FPU enables faster FPU exception handler.
203 # CPU_I486_ON_386 enables CPU cache on i486 based CPU upgrade products
206 # CPU_IORT defines I/O clock delay time (NOTE 1). Default values of
207 # I/O clock delay time on Cyrix 5x86 and 6x86 are 0 and 7,respectively
210 # CPU_L2_LATENCY specified the L2 cache latency value. This option is used
211 # only when CPU_PPRO2CELERON is defined and Mendocino Celeron is detected.
212 # The default value is 5.
214 # CPU_ELAN enables support for AMDs ElanSC520 CPU.
216 # CPU_LOOP_EN prevents flushing the prefetch buffer if the destination
217 # of a jump is already present in the prefetch buffer on Cyrix 5x86(NOTE
220 # CPU_PPRO2CELERON enables L2 cache of Mendocino Celeron CPUs. This option
221 # is useful when you use Socket 8 to Socket 370 converter, because most Pentium
222 # Pro BIOSs do not enable L2 cache of Mendocino Celeron CPUs.
224 # CPU_RSTK_EN enables return stack on Cyrix 5x86 (NOTE 1).
226 # CPU_SUSP_HLT enables suspend on HALT. If this option is set, CPU
227 # enters suspend mode following execution of HALT instruction.
229 # CPU_WT_ALLOC enables write allocation on Cyrix 6x86/6x86MX and AMD
232 # CYRIX_CACHE_WORKS enables CPU cache on Cyrix 486 CPUs with cache
233 # flush at hold state.
235 # CYRIX_CACHE_REALLY_WORKS enables (1) CPU cache on Cyrix 486 CPUs
236 # without cache flush at hold state, and (2) write-back CPU cache on
237 # Cyrix 6x86 whose revision < 2.7 (NOTE 2).
239 # NO_F00F_HACK disables the hack that prevents Pentiums (and ONLY
240 # Pentiums) from locking up when a LOCK CMPXCHG8B instruction is
241 # executed. This option is only needed if I586_CPU is also defined,
242 # and should be included for any non-Pentium CPU that defines it.
244 # NO_MEMORY_HOLE is an optimisation for systems with AMD K6 processors
245 # which indicates that the 15-16MB range is *definitely* not being
246 # occupied by an ISA memory hole.
248 # NOTE 1: The options, CPU_BTB_EN, CPU_LOOP_EN, CPU_IORT,
249 # CPU_LOOP_EN and CPU_RSTK_EN should not be used because of CPU bugs.
250 # These options may crash your system.
252 # NOTE 2: If CYRIX_CACHE_REALLY_WORKS is not set, CPU cache is enabled
253 # in write-through mode when revision < 2.7. If revision of Cyrix
254 # 6x86 >= 2.7, CPU cache is always enabled in write-back mode.
256 # NOTE 3: This option may cause failures for software that requires
257 # locked cycles in order to operate correctly.
259 options CPU_AMD64X2_INTR_SPAM
260 options CPU_ATHLON_SSE_HACK
261 options CPU_BLUELIGHTNING_FPU_OP_CACHE
262 options CPU_BLUELIGHTNING_3X
264 options CPU_CYRIX_NO_LOCK
265 options CPU_DIRECT_MAPPED_CACHE
266 options CPU_DISABLE_5X86_LSSER
267 options CPU_DISABLE_SSE
269 options CPU_ENABLE_EST
270 options CPU_ENABLE_TCC
271 options CPU_FASTER_5X86_FPU
272 options CPU_I486_ON_386
274 options CPU_L2_LATENCY=5
276 options CPU_PPRO2CELERON
280 options CYRIX_CACHE_WORKS
281 options CYRIX_CACHE_REALLY_WORKS
282 #options NO_F00F_HACK
283 options NO_MEMORY_HOLE
286 # A math emulator is mandatory if you wish to run on hardware which
287 # does not have a floating-point processor.
288 options MATH_EMULATE #Support for x87 emulation
290 #####################################################################
291 # COMPATIBILITY OPTIONS
294 # Implement system calls compatible with 4.3BSD and older versions of
295 # FreeBSD. You probably do NOT want to remove this as much current code
296 # still relies on the 4.3 emulation.
301 # Implement system calls compatible with DragonFly 1.2 and older.
303 options COMPAT_DF12 #Compatible with DragonFly 1.2 and earlier
306 # These three options provide support for System V Interface
307 # Definition-style interprocess communication, in the form of shared
308 # memory, semaphores, and message queues, respectively.
310 # System V shared memory and tunable parameters
311 options SYSVSHM # include support for shared memory
312 options SHMMAXPGS=1025 # max amount of shared memory pages (4k on i386)
313 options SHMALL=1025 # max amount of shared memory (bytes)
314 options SHMMAX="(SHMMAXPGS*PAGE_SIZE+1)"
315 # max shared memory segment size (bytes)
316 options SHMMIN=2 # min shared memory segment size (bytes)
317 options SHMMNI=33 # max number of shared memory identifiers
318 options SHMSEG=9 # max shared memory segments per process
320 # System V semaphores and tunable parameters
321 options SYSVSEM # include support for semaphores
322 options SEMMAP=31 # amount of entries in semaphore map
323 options SEMMNI=11 # number of semaphore identifiers in the system
324 options SEMMNS=61 # number of semaphores in the system
325 options SEMMNU=31 # number of undo structures in the system
326 options SEMMSL=61 # max number of semaphores per id
327 options SEMOPM=101 # max number of operations per semop call
328 options SEMUME=11 # max number of undo entries per process
330 # System V message queues and tunable parameters
331 options SYSVMSG # include support for message queues
332 options MSGMNB=2049 # max characters per message queue
333 options MSGMNI=41 # max number of message queue identifiers
334 options MSGSEG=2049 # max number of message segments in the system
335 options MSGSSZ=16 # size of a message segment MUST be power of 2
336 options MSGTQL=41 # max amount of messages in the system
339 #####################################################################
343 # Enable the kernel debugger.
348 # Print a stack trace on kernel panic.
353 # Don't drop into DDB for a panic. Intended for unattended operation
354 # where you may want to drop to DDB from the console, but still want
355 # the machine to recover from a panic
357 options DDB_UNATTENDED
360 # If using GDB remote mode to debug the kernel, there's a non-standard
361 # extension to the remote protocol that can be used to use the serial
362 # port as both the debugging port and the system console. It's non-
363 # standard and you're on your own if you enable it. See also the
364 # "remotechat" variables in the FreeBSD specific version of gdb.
366 options GDB_REMOTE_CHAT
369 # KTRACE enables the system-call tracing facility ktrace(2).
371 options KTRACE #kernel tracing
374 # The INVARIANTS option is used in a number of source files to enable
375 # extra sanity checking of internal structures. This support is not
376 # enabled by default because of the extra time it would take to check
377 # for these conditions, which can only occur as a result of
378 # programming errors.
383 # The DIAGNOSTIC option is used to enable extra debugging information
384 # from some parts of the kernel. As this makes everything more noisy,
385 # it is disabled by default.
390 # PERFMON causes the driver for Pentium/Pentium Pro performance counters
391 # to be compiled. See perfmon(4) for more information.
397 # This option let some drivers co-exist that can't co-exist in a running
398 # system. This is used to be able to compile all kernel code in one go for
399 # quality assurance purposes (like this file, which the option takes it name
402 options COMPILING_LINT
405 # XXX - this doesn't belong here.
406 # Allow ordinary users to take the console - this is useful for X.
409 # XXX - this doesn't belong here either
410 options USERCONFIG #boot -c editor
411 options INTRO_USERCONFIG #imply -c and show intro screen
412 options VISUAL_USERCONFIG #visual boot -c editor
415 #####################################################################
420 # Only the INET (Internet) family is officially supported in FreeBSD.
421 # Source code for the NS (Xerox Network Service) is provided for amusement
424 options INET #Internet communications protocols
425 options INET6 #IPv6 communications protocols
426 options IPSEC #IP security
427 options IPSEC_ESP #IP security (crypto; define w/ IPSEC)
428 options IPSEC_DEBUG #debug for IP security
430 # Set IPSEC_FILTERGIF to force packets coming through a gif tunnel
431 # to be processed by any configured packet filtering (ipfw, ipf).
432 # The default is that packets coming from a tunnel are _not_ processed;
433 # they are assumed trusted.
435 # Note that enabling this can be problematic as there are no mechanisms
436 # in place for distinguishing packets coming out of a tunnel (e.g. no
437 # encX devices as found on openbsd).
439 #options IPSEC_FILTERGIF #filter ipsec packets from a tunnel
442 # Experimental IPsec implementation that uses the kernel crypto
443 # framework. This cannot be configured together with IPSEC and
444 # (currently) supports only IPv4. To use this you must also
445 # configure the crypto device (see below). Note that with this
446 # you get all the IPsec protocols (e.g. there is no FAST_IPSEC_ESP).
447 # IPSEC_DEBUG is used, as above, to configure debugging support
448 # within the IPsec protocols.
450 #options FAST_IPSEC #new IPsec
452 options IPX #IPX/SPX communications protocols
453 options IPXIP #IPX in IP encapsulation (not available)
454 options IPTUNNEL #IP in IPX encapsulation (not available)
456 options NCP #NetWare Core protocol
458 options NETATALK #Appletalk communications protocols
460 # These are currently broken but are shipped due to interest.
461 #options NS #Xerox NS protocols
462 #options NSIP #XNS over IP
466 # NETSMB enables support for SMB protocol, it requires LIBMCHAIN and LIBICONV
468 # NETSMBCRYPTO enables support for encrypted passwords.
469 options NETSMB #SMB/CIFS requester
470 options NETSMBCRYPTO #encrypted password support for SMB
472 # mchain library. It can be either loaded as KLD or compiled into kernel
473 options LIBMCHAIN #mbuf management library
475 # netgraph(4). Enable the base netgraph code with the NETGRAPH option.
476 # Individual node types can be enabled with the corresponding option
477 # listed below; however, this is not strictly necessary as netgraph
478 # will automatically load the corresponding KLD module if the node type
479 # is not already compiled into the kernel. Each type below has a
480 # corresponding man page, e.g., ng_async(4).
481 options NETGRAPH #netgraph(4) system
482 options NETGRAPH_ASYNC
484 options NETGRAPH_BRIDGE
485 options NETGRAPH_CISCO
486 options NETGRAPH_ECHO
487 options NETGRAPH_ETHER
488 options NETGRAPH_FRAME_RELAY
489 options NETGRAPH_HOLE
490 options NETGRAPH_IFACE
491 options NETGRAPH_KSOCKET
492 options NETGRAPH_L2TP
494 # MPPC compression requires proprietary files (not included)
495 #options NETGRAPH_MPPC_COMPRESSION
496 options NETGRAPH_MPPC_ENCRYPTION
497 options NETGRAPH_ONE2MANY
499 options NETGRAPH_PPPOE
500 options NETGRAPH_PPTPGRE
501 options NETGRAPH_RFC1490
502 options NETGRAPH_SOCKET
508 device mn # Munich32x/Falc54 Nx64kbit/sec cards.
511 # Network interfaces:
512 # The `loop' pseudo-device is MANDATORY when networking is enabled.
513 # The `ether' pseudo-device provides generic code to handle
514 # Ethernets; it is MANDATORY when a Ethernet device driver is
515 # configured or token-ring is enabled.
516 # The 'fddi' pseudo-device provides generic code to support FDDI.
517 # The `arcnet' pseudo-device provides generic code to support Arcnet.
518 # The `sppp' pseudo-device serves a similar role for certain types
519 # of synchronous PPP links (like `cx', `ar').
520 # The `sl' pseudo-device implements the Serial Line IP (SLIP) service.
521 # The `ppp' pseudo-device implements the Point-to-Point Protocol.
522 # The `bpf' pseudo-device enables the Berkeley Packet Filter. Be
523 # aware of the legal and administrative consequences of enabling this
524 # option. The number of devices determines the maximum number of
525 # simultaneous BPF clients programs runnable.
526 # The `disc' pseudo-device implements a minimal network interface,
527 # which throws away all packets sent and never receives any. It is
528 # included for testing purposes. This shows up as the 'ds' interface.
529 # The `tun' pseudo-device implements (user-)ppp and nos-tun
530 # The `gif' pseudo-device implements IPv6 over IP4 tunneling,
531 # IPv4 over IPv6 tunneling, IPv4 over IPv4 tunneling and
532 # IPv6 over IPv6 tunneling.
533 # The `gre' device implements two types of IP4 over IP4 tunneling:
534 # GRE and MOBILE, as specified in the RFC1701 and RFC2004.
535 # The `faith' pseudo-device captures packets sent to it and diverts them
536 # to the IPv4/IPv6 translation daemon.
537 # The `stf' device implements 6to4 encapsulation.
538 # The `ef' pseudo-device provides support for multiple ethernet frame types
539 # specified via ETHER_* options. See ef(4) for details.
541 # The PPP_BSDCOMP option enables support for compress(1) style entire
542 # packet compression, the PPP_DEFLATE is for zlib/gzip style compression.
543 # PPP_FILTER enables code for filtering the ppp data stream and selecting
544 # events for resetting the demand dial activity timer - requires bpf.
545 # See pppd(8) for more details.
547 pseudo-device ether #Generic Ethernet
548 pseudo-device vlan 1 #VLAN support
549 pseudo-device bridge #Bridging support
550 pseudo-device token #Generic TokenRing
551 pseudo-device fddi #Generic FDDI
552 pseudo-device arcnet #Generic Arcnet
553 pseudo-device sppp #Generic Synchronous PPP
554 pseudo-device loop #Network loopback device
555 pseudo-device bpf #Berkeley packet filter
556 pseudo-device disc #Discard device (ds0, ds1, etc)
557 pseudo-device tun #Tunnel driver (ppp(8), nos-tun(8))
558 pseudo-device sl 2 #Serial Line IP
559 pseudo-device gre #IP over IP tunneling
560 pseudo-device ppp 2 #Point-to-point protocol
561 options PPP_BSDCOMP #PPP BSD-compress support
562 options PPP_DEFLATE #PPP zlib/deflate/gzip support
563 options PPP_FILTER #enable bpf filtering (needs bpf)
565 pseudo-device ef # Multiple ethernet frames support
566 options ETHER_II # enable Ethernet_II frame
567 options ETHER_8023 # enable Ethernet_802.3 (Novell) frame
568 options ETHER_8022 # enable Ethernet_802.2 frame
569 options ETHER_SNAP # enable Ethernet_802.2/SNAP frame
572 pseudo-device gif #IPv6 and IPv4 tunneling
573 pseudo-device faith 1 #for IPv6 and IPv4 translation
574 pseudo-device stf #6to4 IPv6 over IPv4 encapsulation
577 # Internet family options:
579 # MROUTING enables the kernel multicast packet forwarder, which works
582 # PIM enables Protocol Independent Multicast in the kernel.
583 # Requires MROUTING enabled.
585 # IPFIREWALL enables support for IP firewall construction, in
586 # conjunction with the `ipfw' program. IPFIREWALL_VERBOSE sends
587 # logged packets to the system logger. IPFIREWALL_VERBOSE_LIMIT
588 # limits the number of times a matching entry can be logged.
590 # WARNING: IPFIREWALL defaults to a policy of "deny ip from any to any"
591 # and if you do not add other rules during startup to allow access,
592 # YOU WILL LOCK YOURSELF OUT. It is suggested that you set firewall_type=open
593 # in /etc/rc.conf when first enabling this feature, then refining the
594 # firewall rules in /etc/rc.firewall after you've tested that the new kernel
595 # feature works properly.
597 # IPFIREWALL_DEFAULT_TO_ACCEPT causes the default rule (at boot) to
598 # allow everything. Use with care, if a cracker can crash your
599 # firewall machine, they can get to your protected machines. However,
600 # if you are using it as an as-needed filter for specific problems as
601 # they arise, then this may be for you. Changing the default to 'allow'
602 # means that you won't get stuck if the kernel and /sbin/ipfw binary get
605 # IPDIVERT enables the divert IP sockets, used by ``ipfw divert''
607 # IPSTEALTH enables code to support stealth forwarding (i.e., forwarding
608 # packets without touching the ttl). This can be useful to hide firewalls
609 # from traceroute and similar tools.
611 # TCPDEBUG is undocumented.
613 options MROUTING # Multicast routing
614 options PIM # Protocol Independent Multicast
615 options IPFIREWALL #firewall
616 options IPFIREWALL_VERBOSE #enable logging to syslogd(8)
617 options IPFIREWALL_FORWARD #enable transparent proxy support
618 options IPFIREWALL_VERBOSE_LIMIT=100 #limit verbosity
619 options IPFIREWALL_DEFAULT_TO_ACCEPT #allow everything by default
620 options IPV6FIREWALL #firewall for IPv6
621 options IPV6FIREWALL_VERBOSE
622 options IPV6FIREWALL_VERBOSE_LIMIT=100
623 options IPV6FIREWALL_DEFAULT_TO_ACCEPT
624 options IPDIVERT #divert sockets
625 options IPFILTER #ipfilter support
626 options IPFILTER_LOG #ipfilter logging
627 options IPFILTER_DEFAULT_BLOCK #block all packets by default
628 options IPSTEALTH #support for stealth forwarding
630 options NS # NETNS support
636 # The MBUF_STRESS_TEST option enables options which create
637 # various random failures / extreme cases related to mbuf
638 # functions. See the mbuf(9) manpage for a list of available
640 options MBUF_STRESS_TEST
642 # Statically link in accept filters
643 options ACCEPT_FILTER_DATA
644 options ACCEPT_FILTER_HTTP
647 # TCP_DROP_SYNFIN adds support for ignoring TCP packets with SYN+FIN. This
648 # prevents nmap et al. from identifying the TCP/IP stack, but breaks support
649 # for RFC1644 extensions and is not recommended for web servers.
651 options TCP_DROP_SYNFIN #drop TCP packets with SYN+FIN
653 # ICMP_BANDLIM enables icmp error response bandwidth limiting. You
654 # typically want this option as it will help protect the machine from
655 # D.O.S. packet attacks.
659 # DUMMYNET enables the "dummynet" bandwidth limiter. You need
660 # IPFIREWALL as well. See the dummynet(4) and ipfw(8) manpages for more info.
661 # When you run DUMMYNET it is advisable to also have "options HZ=1000"
662 # to achieve a smoother scheduling of the traffic.
667 # ATM (HARP version) options
669 # ATM_CORE includes the base ATM functionality code. This must be included
672 # ATM_IP includes support for running IP over ATM.
674 # At least one (and usually only one) of the following signalling managers
675 # must be included (note that all signalling managers include PVC support):
676 # ATM_SIGPVC includes support for the PVC-only signalling manager `sigpvc'.
677 # ATM_SPANS includes support for the `spans' signalling manager, which runs
678 # the FORE Systems's proprietary SPANS signalling protocol.
679 # ATM_UNI includes support for the `uni30' and `uni31' signalling managers,
680 # which run the ATM Forum UNI 3.x signalling protocols.
682 # The `hea' driver provides support for the Efficient Networks, Inc.
683 # ENI-155p ATM PCI Adapter.
685 # The `hfa' driver provides support for the FORE Systems, Inc.
686 # PCA-200E ATM PCI Adapter.
688 options ATM_CORE #core ATM protocol family
689 options ATM_IP #IP over ATM support
690 options ATM_SIGPVC #SIGPVC signalling manager
691 options ATM_SPANS #SPANS signalling manager
692 options ATM_UNI #UNI signalling manager
693 device hea #Efficient ENI-155p ATM PCI
694 device hfa #FORE PCA-200E ATM PCI
696 # DEVICE_POLLING adds support for mixed interrupt-polling handling
697 # of network device drivers, which has significant benefits in terms
698 # of robustness to overloads and responsivity, as well as permitting
699 # accurate scheduling of the CPU time between kernel network processing
700 # and other activities. The drawback is a moderate (up to 1/HZ seconds)
701 # potential increase in response times.
703 # Additionally, you can enable/disable polling at runtime with the
704 # sysctl variable kern.polling.enable (defaults off), set polling
705 # frequency with the sysctl variable kern.polling.pollhz (default 2000,
706 # range 1..30000) and select the CPU fraction reserved to userland with
707 # the sysctl variable kern.polling.user_frac (default 50, range 0..100).
709 # It is strongly recommended to set the sysctl variable kern.polling.pollhz
710 # to 1000 or 2000 as to achieve smoother behaviour.
712 # Only the following devices support this mode of operation at the time of
715 # bce, bge, dc, em, fwe, fxp, nfe, nge, nv, re, rl, sis, stge, vge, vr, wi, xl
717 options DEVICE_POLLING
720 #####################################################################
724 # Only the root, /usr, and /tmp filesystems need be statically
725 # compiled; everything else will be automatically loaded at mount
726 # time. (Exception: the UFS family---FFS, and MFS --- cannot
727 # currently be demand-loaded.) Some people still prefer to statically
728 # compile other filesystems as well.
730 # NB: The PORTAL and UNION filesystems are known to be
731 # buggy, and WILL panic your system if you attempt to do anything with
732 # them. They are included here as an incentive for some enterprising
733 # soul to sit down and fix them.
736 # One of these is mandatory:
737 options FFS #Fast filesystem
738 options MFS #Memory filesystem
739 options NFS #Network filesystem
741 # The rest are optional:
742 #options NFS_NOSERVER #Disable the NFS-server code.
743 options CD9660 #ISO 9660 filesystem
744 options FDESC #File descriptor filesystem
745 options MSDOSFS #MS DOS filesystem
746 options NTFS #NT filesystem
747 options NULLFS #NULL filesystem
748 options NWFS #NetWare filesystem
749 options PORTAL #Portal filesystem
750 options PROCFS #Process filesystem
751 options SMBFS #SMB/CIFS filesystem
752 options UDF #UDF filesystem
753 # YYY-DR Till we rework the VOP methods for this filesystem
754 #options UNION #Union filesystem
755 # The xFS_ROOT options REQUIRE the associated ``options xFS''
756 options FFS_ROOT #FFS usable as root device
757 options NFS_ROOT #NFS usable as root device
759 # Soft updates is technique for improving filesystem speed and
760 # making abrupt shutdown less risky.
763 # Directory hashing improves the speed of operations on very large
764 # directories at the expense of some memory.
767 # Make space in the kernel for a root filesystem on a md device.
768 # Define to the number of kilobytes to reserve for the filesystem.
769 options MD_ROOT_SIZE=10
771 # Make the md device a potential root device, either with preloaded
772 # images of type mfs_root or md_root.
775 # Specify double the default maximum size for malloc(9)-backed md devices.
776 options MD_NSECT=40000
778 # Allow this many swap-devices.
780 # In order to manage swap, the system must reserve bitmap space that
781 # scales with the largest mounted swap device multiplied by NSWAPDEV,
782 # irregardless of whether other swap devices exist or not. So it
783 # is not a good idea to make this value too large.
786 # Disk quotas are supported when this option is enabled.
787 options QUOTA #enable disk quotas
789 # If you are running a machine just as a fileserver for PC and MAC
790 # users, using SAMBA or Netatalk, you may consider setting this option
791 # and keeping all those users' directories on a filesystem that is
792 # mounted with the suiddir option. This gives new files the same
793 # ownership as the directory (similar to group). It's a security hole
794 # if you let these users run programs, so confine it to file-servers
795 # (but it'll save you lots of headaches in those cases). Root owned
796 # directories are exempt and X bits are cleared. The suid bit must be
797 # set on the directory as well; see chmod(1) PC owners can't see/set
798 # ownerships so they keep getting their toes trodden on. This saves
799 # you all the support calls as the filesystem it's used on will act as
800 # they expect: "It's my dir so it must be my file".
805 options NFS_MINATTRTIMO=3 # VREG attrib cache timeout in sec
806 options NFS_MAXATTRTIMO=60
807 options NFS_MINDIRATTRTIMO=30 # VDIR attrib cache timeout in sec
808 options NFS_MAXDIRATTRTIMO=60
809 options NFS_GATHERDELAY=10 # Default write gather delay (msec)
810 options NFS_UIDHASHSIZ=29 # Tune the size of nfssvc_sock with this
811 options NFS_WDELAYHASHSIZ=16 # and with this
812 options NFS_MUIDHASHSIZ=63 # Tune the size of nfsmount with this
813 options NFS_DEBUG # Enable NFS Debugging
816 # Add support for the EXT2FS filesystem of Linux fame. Be a bit
817 # careful with this - the ext2fs code has a tendency to lag behind
818 # changes and not be exercised very much, so mounting read/write could
819 # be dangerous (and even mounting read only could result in panics.)
823 # Use real implementations of the aio_* system calls. There are numerous
824 # stability and security issues in the current aio code that make it
825 # unsuitable for inclusion on machines with untrusted local users.
829 #####################################################################
832 # Real time extensions added in the 1993 Posix
833 # P1003_1B: Infrastructure
834 # _KPOSIX_PRIORITY_SCHEDULING: Build in _POSIX_PRIORITY_SCHEDULING
835 # _KPOSIX_VERSION: Version kernel is built for
838 options _KPOSIX_PRIORITY_SCHEDULING
839 options _KPOSIX_VERSION=199309L
842 #####################################################################
845 # The granularity of operation is controlled by the kernel option HZ whose
846 # default value (100) means a granularity of 10ms (1s/HZ).
847 # Some subsystems, such as DUMMYNET or DEVICE_POLLING, might benefit from
848 # a smaller granularity such as 1ms or less.
849 # Consider, however, that reducing the granularity too much might
850 # cause excessive overhead in clock interrupt processing,
851 # potentially causing ticks to be missed and thus actually reducing
852 # the accuracy of operation.
856 # The following options are used for debugging clock behavior only, and
857 # should not be used for production systems.
859 # CLK_CALIBRATION_LOOP will run the clock calibration loop at startup
860 # until the user presses a key.
862 options CLK_CALIBRATION_LOOP
864 # The following two options measure the frequency of the corresponding
865 # clock relative to the RTC (onboard mc146818a).
867 options CLK_USE_I8254_CALIBRATION
868 options CLK_USE_TSC_CALIBRATION
871 #####################################################################
874 # SCSI DEVICE CONFIGURATION
876 # The SCSI subsystem consists of the `base' SCSI code, a number of
877 # high-level SCSI device `type' drivers, and the low-level host-adapter
878 # device drivers. The host adapters are listed in the ISA and PCI
879 # device configuration sections below.
881 # Beginning with FreeBSD 2.0.5 you can wire down your SCSI devices so
882 # that a given bus, target, and LUN always come on line as the same
883 # device unit. In earlier versions the unit numbers were assigned
884 # in the order that the devices were probed on the SCSI bus. This
885 # means that if you removed a disk drive, you may have had to rewrite
886 # your /etc/fstab file, and also that you had to be careful when adding
887 # a new disk as it may have been probed earlier and moved your device
888 # configuration around.
890 # This old behavior is maintained as the default behavior. The unit
891 # assignment begins with the first non-wired down unit for a device
892 # type. For example, if you wire a disk as "da3" then the first
893 # non-wired disk will be assigned da4.
895 # The syntax for wiring down devices is:
897 # device scbus0 at ahc0 # Single bus device
898 # device scbus1 at ahc1 bus 0 # Single bus device
899 # device scbus3 at ahc2 bus 0 # Twin bus device
900 # device scbus2 at ahc2 bus 1 # Twin bus device
901 # device da0 at scbus0 target 0 unit 0
902 # device da1 at scbus3 target 1
903 # device da2 at scbus2 target 3
904 # device sa1 at scbus1 target 6
907 # "units" (SCSI logical unit number) that are not specified are
908 # treated as if specified as LUN 0.
910 # All SCSI devices allocate as many units as are required.
912 # The "unknown" device (uk? in pre-2.0.5) is now part of the base SCSI
913 # configuration and doesn't have to be explicitly configured.
915 device scbus #base SCSI code
916 device ch #SCSI media changers
917 device da #SCSI direct access devices (aka disks)
918 device sa #SCSI tapes
919 device cd #SCSI CD-ROMs
920 device pass #CAM passthrough driver
921 device pt #SCSI processor type
922 device ses #SCSI SES/SAF-TE driver
926 # -- NOTE -- If you specify one of the bus/target/lun options, you must
928 # CAMDEBUG: When defined enables debugging macros
929 # CAM_DEBUG_BUS: Debug the given bus. Use -1 to debug all busses.
930 # CAM_DEBUG_TARGET: Debug the given target. Use -1 to debug all targets.
931 # CAM_DEBUG_LUN: Debug the given lun. Use -1 to debug all luns.
932 # CAM_DEBUG_FLAGS: OR together CAM_DEBUG_INFO, CAM_DEBUG_TRACE,
933 # CAM_DEBUG_SUBTRACE, and CAM_DEBUG_CDB
935 # CAM_MAX_HIGHPOWER: Maximum number of concurrent high power (start unit) cmds
936 # SCSI_NO_SENSE_STRINGS: When defined disables sense descriptions
937 # SCSI_NO_OP_STRINGS: When defined disables opcode descriptions
938 # SCSI_DELAY: The number of MILLISECONDS to freeze the SIM (scsi adapter)
939 # queue after a bus reset, and the number of milliseconds to
940 # freeze the device queue after a bus device reset.
942 options CAM_DEBUG_BUS=-1
943 options CAM_DEBUG_TARGET=-1
944 options CAM_DEBUG_LUN=-1
945 options CAM_DEBUG_FLAGS="CAM_DEBUG_INFO|CAM_DEBUG_TRACE|CAM_DEBUG_CDB"
946 options CAM_MAX_HIGHPOWER=4
947 options SCSI_NO_SENSE_STRINGS
948 options SCSI_NO_OP_STRINGS
949 options SCSI_DELAY=8000 # Be pessimistic about Joe SCSI device
951 # Options for the CAM CDROM driver:
952 # CHANGER_MIN_BUSY_SECONDS: Guaranteed minimum time quantum for a changer LUN
953 # CHANGER_MAX_BUSY_SECONDS: Maximum time quantum per changer LUN, only
954 # enforced if there is I/O waiting for another LUN
955 # The compiled in defaults for these variables are 2 and 10 seconds,
958 # These can also be changed on the fly with the following sysctl variables:
959 # kern.cam.cd.changer.min_busy_seconds
960 # kern.cam.cd.changer.max_busy_seconds
962 options CHANGER_MIN_BUSY_SECONDS=2
963 options CHANGER_MAX_BUSY_SECONDS=10
965 # Options for the CAM sequential access driver:
966 # SA_IO_TIMEOUT: Timeout for read/write/wfm operations, in minutes
967 # SA_SPACE_TIMEOUT: Timeout for space operations, in minutes
968 # SA_REWIND_TIMEOUT: Timeout for rewind operations, in minutes
969 # SA_ERASE_TIMEOUT: Timeout for erase operations, in minutes
970 # SA_1FM_AT_EOD: Default to model which only has a default one filemark at EOT.
971 options SA_IO_TIMEOUT="(4)"
972 options SA_SPACE_TIMEOUT="(60)"
973 options SA_REWIND_TIMEOUT="(2*60)"
974 options SA_ERASE_TIMEOUT="(4*60)"
975 options SA_1FM_AT_EOD
977 # Optional timeout for the CAM processor target (pt) device
978 # This is specified in seconds. The default is 60 seconds.
979 options SCSI_PT_DEFAULT_TIMEOUT="60"
981 # Optional enable of doing SES passthrough on other devices (e.g., disks)
983 # Normally disabled because a lot of newer SCSI disks report themselves
984 # as having SES capabilities, but this can then clot up attempts to build
985 # build a topology with the SES device that's on the box these drives
987 options SES_ENABLE_PASSTHROUGH
990 #####################################################################
991 # MISCELLANEOUS DEVICES AND OPTIONS
993 # The `pty' device usually turns out to be ``effectively mandatory'',
994 # as it is required for `telnetd', `rlogind', `screen', `emacs', and
995 # `xterm', among others.
997 pseudo-device pty #Pseudo ttys
998 pseudo-device gzip #Exec gzipped a.out's
999 pseudo-device vn #Vnode driver (turns a file into a device)
1000 pseudo-device md #Memory/malloc disk
1001 pseudo-device snp #Snoop device - to look at pty/vty/etc..
1002 pseudo-device ccd 4 #Concatenated disk driver
1004 # Configuring Vinum into the kernel is not necessary, since the kld
1005 # module gets started automatically when vinum(8) starts. This
1006 # device is also untested. Use at your own risk.
1008 # The option VINUMDEBUG must match the value set in CFLAGS
1009 # in src/sbin/vinum/Makefile. Failure to do so will result in
1010 # the following message from vinum(8):
1012 # Can't get vinum config: Invalid argument
1014 # see vinum(4) for more reasons not to use these options.
1015 pseudo-device vinum #Vinum concat/mirror/raid driver
1016 options VINUMDEBUG #enable Vinum debugging hooks
1018 # Kernel side iconv library
1021 # Size of the kernel message buffer. Should be N * pagesize.
1022 options MSGBUF_SIZE=40960
1025 #####################################################################
1026 # HARDWARE DEVICE CONFIGURATION
1028 # ISA and EISA devices:
1029 # EISA support is available for some device, so they can be auto-probed.
1032 # Mandatory ISA devices: isa, npx
1036 # ISA-PnP BIOS support
1040 # Options for `isa':
1042 # AUTO_EOI_1 enables the `automatic EOI' feature for the master 8259A
1043 # interrupt controller. This saves about 0.7-1.25 usec for each interrupt.
1044 # This option breaks suspend/resume on some portables.
1046 # AUTO_EOI_2 enables the `automatic EOI' feature for the slave 8259A
1047 # interrupt controller. This saves about 0.7-1.25 usec for each interrupt.
1048 # Automatic EOI is documented not to work for for the slave with the
1049 # original i8259A, but it works for some clones and some integrated
1052 # MAXMEM specifies the amount of RAM on the machine; if this is not
1053 # specified, FreeBSD will first read the amount of memory from the CMOS
1054 # RAM, so the amount of memory will initially be limited to 64MB or 16MB
1055 # depending on the BIOS. If the BIOS reports 64MB, a memory probe will
1056 # then attempt to detect the installed amount of RAM. If this probe
1057 # fails to detect >64MB RAM you will have to use the MAXMEM option.
1058 # The amount is in kilobytes, so for a machine with 128MB of RAM, it would
1059 # be 131072 (128 * 1024).
1061 # BROKEN_KEYBOARD_RESET disables the use of the keyboard controller to
1062 # reset the CPU for reboot. This is needed on some systems with broken
1063 # keyboard controllers.
1065 # PAS_JOYSTICK_ENABLE enables the gameport on the ProAudio Spectrum
1067 options COMPAT_OLDISA #FreeBSD 2.2 and 3.x compatibility shims
1070 options MAXMEM="(128*1024)"
1071 #options BROKEN_KEYBOARD_RESET
1072 #options PAS_JOYSTICK_ENABLE
1074 # Enable support for the kernel PLL to use an external PPS signal,
1075 # under supervision of [x]ntpd(8)
1076 # More info in ntpd documentation: http://www.eecis.udel.edu/~ntp
1080 # The keyboard controller; it controls the keyboard and the PS/2 mouse.
1081 device atkbdc0 at isa? port IO_KBD
1084 device atkbd0 at atkbdc? irq 1
1086 # Options for atkbd:
1087 options ATKBD_DFLT_KEYMAP # specify the built-in keymap
1088 makeoptions ATKBD_DFLT_KEYMAP="jp.106"
1090 # These options are valid for other keyboard drivers as well.
1091 options KBD_DISABLE_KEYMAP_LOAD # refuse to load a keymap
1092 options KBD_INSTALL_CDEV # install a CDEV entry in /dev
1094 # `flags' for atkbd:
1095 # 0x01 Force detection of keyboard, else we always assume a keyboard
1096 # 0x02 Don't reset keyboard, useful for some newer ThinkPads
1097 # 0x03 Force detection and avoid reset, might help with certain
1099 # 0x04 Old-style (XT) keyboard support, useful for older ThinkPads
1102 device psm0 at atkbdc? irq 12
1105 options PSM_HOOKRESUME #hook the system resume event, useful
1107 options PSM_RESETAFTERSUSPEND #reset the device at the resume event
1109 # The video card driver.
1113 # Try the following option if the mouse pointer is not drawn correctly
1114 # or font does not seem to be loaded properly. May cause flicker on
1116 options VGA_ALT_SEQACCESS
1118 options VGA_DEBUG=2 # enable VGA debug output
1120 # If you can dispense with some vga driver features, you may want to
1121 # use the following options to save some memory.
1122 options VGA_NO_FONT_LOADING # don't save/load font
1123 options VGA_NO_MODE_CHANGE # don't change video modes
1125 # Older video cards may require this option for proper operation.
1126 options VGA_SLOW_IOACCESS # do byte-wide i/o's to TS and GDC regs
1128 # The following option probably won't work with the LCD displays.
1129 options VGA_WIDTH90 # support 90 column modes
1131 # To include support for VESA video modes
1133 options VESA_DEBUG=2 # enable VESA debug output
1135 # Splash screen at start up! Screen savers require this too.
1136 pseudo-device splash
1138 # The syscons console driver (sco color console compatible).
1140 options MAXCONS=16 # number of virtual consoles
1141 options SC_ALT_MOUSE_IMAGE # simplified mouse cursor in text mode
1142 options SC_DEBUG_LEVEL=5 # enable debug output
1143 options SC_DFLT_FONT # compile font in
1144 makeoptions SC_DFLT_FONT=cp850
1145 options SC_DISABLE_DDBKEY # disable `debug' key
1146 options SC_DISABLE_REBOOT # disable reboot key sequence
1147 options SC_HISTORY_SIZE=200 # number of history buffer lines
1148 options SC_MOUSE_CHAR=0x3 # char code for text mode mouse cursor
1149 options SC_PIXEL_MODE # add support for the raster text mode
1151 # The following options will let you change the default colors of syscons.
1152 options SC_NORM_ATTR="(FG_GREEN|BG_BLACK)"
1153 options SC_NORM_REV_ATTR="(FG_YELLOW|BG_GREEN)"
1154 options SC_KERNEL_CONS_ATTR="(FG_RED|BG_BLACK)"
1155 options SC_KERNEL_CONS_REV_ATTR="(FG_BLACK|BG_RED)"
1157 # If you have a two button mouse, you may want to add the following option
1158 # to use the right button of the mouse to paste text.
1159 options SC_TWOBUTTON_MOUSE
1161 # You can selectively disable features in syscons.
1162 options SC_NO_CUTPASTE
1163 options SC_NO_FONT_LOADING
1164 options SC_NO_HISTORY
1165 options SC_NO_SYSMOUSE
1168 # The Numeric Processing eXtension driver. In addition to this, you
1169 # may configure a math emulator (see above). If your machine has a
1170 # hardware FPU and the kernel configuration includes the npx device
1171 # *and* a math emulator compiled into the kernel, the hardware FPU
1172 # will be used, unless it is found to be broken or unless "flags" to
1173 # npx0 includes "0x08", which requests preference for the emulator.
1174 device npx0 at nexus? port IO_NPX flags 0x0 irq 13
1178 # 0x01 don't use the npx registers to optimize bcopy.
1179 # 0x02 don't use the npx registers to optimize bzero.
1180 # 0x04 don't use the npx registers to optimize copyin or copyout.
1181 # 0x08 use emulator even if hardware FPU is available.
1182 # The npx registers are normally used to optimize copying and zeroing when
1183 # all of the following conditions are satisfied:
1184 # I586_CPU is an option
1185 # the cpu is an i586 (perhaps not a Pentium)
1186 # the probe for npx0 succeeds
1187 # INT 16 exception handling works.
1188 # Then copying and zeroing using the npx registers is normally 30-100% faster.
1189 # The flags can be used to control cases where it doesn't work or is slower.
1190 # Setting them at boot time using userconfig works right (the optimizations
1191 # are not used until later in the bootstrap when npx0 is attached).
1192 # Flag 0x08 automatically disables the i586 optimized routines.
1196 # Optional ISA and EISA devices:
1200 # SCSI host adapters: `aha', `aic', `bt'
1202 # adv: All Narrow SCSI bus AdvanSys controllers.
1203 # adw: Second Generation AdvanSys controllers including the ADV940UW.
1205 # ahc: Adaptec 274x/284x/294x
1207 # bt: Most Buslogic controllers
1208 # ncv: NCR 53C500 based SCSI host adapters.
1209 # nsp: Workbit Ninja SCSI-3 based PC Card SCSI host adapters.
1210 # stg: TMC 18C30, 18C50 based ISA/PC Card SCSI host adapters.
1212 # Note that the order is important in order for Buslogic cards to be
1216 device bt0 at isa? port IO_BT0
1223 device stg0 at isa? port 0x140 irq 11
1226 # Adaptec FSA RAID controllers, including integrated DELL controller,
1227 # the Dell PERC 2/QC and the HP NetRAID-4M
1230 device aacp # SCSI Passthrough interface (optional, CAM required)
1233 # Compaq Smart RAID, Mylex DAC960 and AMI MegaRAID controllers. Only
1234 # one entry is needed; the code will find and configure all supported
1237 device ida # Compaq Smart RAID
1238 device mlx # Mylex DAC960
1239 device amr # AMI MegaRAID
1244 device twe # 3ware ATA RAID
1245 device twa # 3ware SATA RAID
1246 options TWA_DEBUG=10 # enable debug messages
1247 options TWA_FLASH_FIRMWARE
1250 # Promise Supertrack SX6000
1260 # The 'ATA' driver supports all ATA and ATAPI devices.
1261 # You only need one "device ata" for it to find all
1262 # PCI ATA/ATAPI devices on modern machines.
1264 device atadisk # ATA disk drives
1265 device atapicd # ATAPI CDROM drives
1266 device atapifd # ATAPI floppy drives
1267 device atapist # ATAPI tape drives
1268 device atapicam # emulate ATAPI devices as SCSI ditto via CAM
1269 # needs CAM to be present (scbus & pass)
1270 # The 'NATA' set of drivers are set to replace the previous ATA drivers,
1271 # and this set of drivers is mutually exclusive with the old ones. This means,
1272 # you can't have both at the same time!
1274 #device natadisk # ATA disk drives
1275 #device natapicd # ATAPI CD/DVD drives
1276 #device natapifd # ATAPI floppy drives
1277 #device natapist # ATAPI tape drives
1278 #device natapicam # ATAPI CAM layer emulation
1279 #device nataraid # support for ATA software RAID controllers
1280 #device natausb # ATA-over-USB support
1282 #The following options are valid on the ATA driver:
1284 # ATA_STATIC_ID: controller numbering is static (like the old driver)
1285 # else the device numbers are dynamically allocated.
1286 options ATA_STATIC_ID
1289 # For older non-PCI systems, these are the lines to use:
1290 #device ata0 at isa? port IO_WD1 irq 14
1291 #device ata1 at isa? port IO_WD2 irq 15
1294 # Standard floppy disk controllers: `fdc' and `fd'
1296 device fdc0 at isa? port IO_FD1 irq 6 drq 2
1298 # FDC_DEBUG enables floppy debugging. Since the debug output is huge, you
1299 # gotta turn it actually on by setting the variable fd_debug with DDB,
1303 device fd0 at fdc0 drive 0
1304 device fd1 at fdc0 drive 1
1306 # M-systems DiskOnchip products see src/sys/contrib/dev/fla/README
1310 # Other standard PC hardware: `mse', `sio', etc.
1312 # mse: Logitech and ATI InPort bus mouse ports
1313 # sio: serial ports (see sio(4))
1315 device mse0 at isa? port 0x23c irq 5
1317 device sio0 at isa? port IO_COM1 flags 0x10 irq 4
1320 # `flags' for serial drivers that support consoles (only for sio now):
1321 # 0x10 enable console support for this unit. The other console flags
1322 # are ignored unless this is set. Enabling console support does
1323 # not make the unit the preferred console - boot with -h or set
1324 # the 0x20 flag for that. Currently, at most one unit can have
1325 # console support; the first one (in config file order) with
1326 # this flag set is preferred. Setting this flag for sio0 gives
1327 # the old behaviour.
1328 # 0x20 force this unit to be the console (unless there is another
1329 # higher priority console). This replaces the COMCONSOLE option.
1330 # 0x40 reserve this unit for low level console operations. Do not
1331 # access the device in any normal way.
1332 # 0x80 use this port for serial line gdb support in ddb.
1334 # PnP `flags' (set via userconfig using pnp x flags y)
1335 # 0x1 disable probing of this device. Used to prevent your modem
1336 # from being attached as a PnP modem.
1339 # Options for serial drivers that support consoles (only for sio now):
1340 options BREAK_TO_DEBUGGER #a BREAK on a comconsole goes to
1342 options CONSPEED=115200 # speed for serial console
1345 # Solaris implements a new BREAK which is initiated by a character
1346 # sequence CR ~ ^b which is similar to a familiar pattern used on
1347 # Sun servers by the Remote Console.
1348 options ALT_BREAK_TO_DEBUGGER
1351 options COM_ESP #code for Hayes ESP
1352 options COM_MULTIPORT #code for some cards with shared IRQs
1354 # Other flags for sio that aren't documented in the man page.
1355 # 0x20000 enable hardware RTS/CTS and larger FIFOs. Only works for
1356 # ST16650A-compatible UARTs.
1358 # PCI Universal Communications driver
1359 # Supports various single and multi port PCI serial cards. Maybe later
1360 # also the parallel ports on combination serial/parallel cards. New cards
1361 # can be added in src/sys/dev/puc/pucdata.c.
1363 # If the PUC_FASTINTR option is used the driver will try to use fast
1364 # interrupts. The card must then be the only user of that interrupt.
1365 # Interrupts cannot be shared when using PUC_FASTINTR.
1367 options PUC_FASTINTR
1370 # Network interfaces: `cx', `ed', `el', `ep', `ie', `is', `le', `lnc'
1372 # ar: Arnet SYNC/570i hdlc sync 2/4 port V.35/X.21 serial driver (requires sppp)
1373 # cm: Arcnet SMC COM90c26 / SMC COM90c56
1374 # (and SMC COM90c66 in '56 compatibility mode) adapters.
1375 # cs: IBM Etherjet and other Crystal Semi CS89x0-based adapters
1376 # cx: Cronyx/Sigma multiport sync/async (with Cisco or PPP framing)
1377 # ed: Western Digital and SMC 80xx; Novell NE1000 and NE2000; 3Com 3C503
1378 # el: 3Com 3C501 (slow!)
1380 # ex: Intel EtherExpress Pro/10 and other i82595-based adapters
1381 # fe: Fujitsu MB86960A/MB86965A Ethernet
1382 # ie: AT&T StarLAN 10 and EN100; 3Com 3C507; unknown NI5210; Intel EtherExpress
1383 # le: Digital Equipment EtherWorks 2 and EtherWorks 3 (DEPCA, DE100,
1384 # DE101, DE200, DE201, DE202, DE203, DE204, DE205, DE422)
1385 # lnc: Lance/PCnet cards (Isolan, Novell NE2100, NE32-VL, AMD Am7990 & Am79C960)
1386 # rdp: RealTek RTL 8002-based pocket ethernet adapters
1387 # sbni: Granch SBNI12-xx adapters
1388 # sbsh: Granch SBNI16 SHDSL modem PCI adapters
1389 # sr: RISCom/N2 hdlc sync 1/2 port V.35/X.21 serial driver (requires sppp)
1390 # wl: Lucent Wavelan (ISA card only).
1391 # awi: IEEE 802.11b PRISM I cards.
1392 # wi: Lucent WaveLAN/IEEE 802.11 PCMCIA adapters. Note: this supports both
1393 # the PCMCIA and ISA cards: the ISA card is really a PCMCIA to ISA
1394 # bridge with a PCMCIA adapter plugged into it.
1395 # an: Aironet 4500/4800 802.11 wireless adapters. Supports the PCMCIA,
1396 # PCI and ISA varieties.
1397 # xe: Xircom/Intel EtherExpress Pro100/16 PC Card ethernet controller.
1398 # ray: Raytheon Raylink 802.11 wireless NICs, OEM as Webgear Aviator 2.4GHz
1399 # oltr: Olicom ISA token-ring adapters OC-3115, OC-3117, OC-3118 and OC-3133
1400 # (no options needed)
1402 device ar0 at isa? port 0x300 irq 10 iomem 0xd0000
1403 device cm0 at isa? port 0x2e0 irq 9 iomem 0xdc000
1404 device cs0 at isa? port 0x300
1405 device cx0 at isa? port 0x240 irq 15 drq 7
1406 device ed0 at isa? port 0x280 irq 5 iomem 0xd8000
1407 device el0 at isa? port 0x300 irq 9
1410 device fe0 at isa? port 0x300
1411 device ie0 at isa? port 0x300 irq 5 iomem 0xd0000
1412 device ie1 at isa? port 0x360 irq 7 iomem 0xd0000
1413 device le0 at isa? port 0x300 irq 5 iomem 0xd0000
1414 device lnc0 at isa? port 0x280 irq 10 drq 0
1415 device rdp0 at isa? port 0x378 irq 7 flags 2
1416 device sbni0 at isa? port 0x210 irq 5 flags 0xefdead
1417 device sr0 at isa? port 0x300 irq 5 iomem 0xd0000
1418 device sn0 at isa? port 0x300 irq 10
1420 # Wlan support is mandatory for some wireless LAN devices.
1421 device wlan # 802.11 support
1422 device wlan_acl # 802.11 MAC-based access control for AP
1423 device wlan_ccmp # 802.11 CCMP support
1424 device wlan_tkip # 802.11 TKIP support
1425 device wlan_wep # 802.11 WEP support
1426 device wlan_xauth # 802.11 WPA or 802.1x authentication for AP
1427 device wlan_ratectl_onoe # 802.11 Onoe TX rate control algorithm
1428 device wlan_ratectl_amrr # 802.11 AMRR TX rate control algorithm
1429 device wlan_ratectl_sample # 802.11 Sample TX rate control algorithm
1430 options WLCACHE # enables the signal-strength cache
1431 options WLDEBUG # enables verbose debugging output
1432 device awi # AMD PCnetMobile
1433 device an # Aironet Communications 4500/4800
1434 device ipw # Intel PRO/Wireless 2100
1435 device iwi # Intel PRO/Wireless 2200BG/2915ABG
1436 device wi # WaveLAN/IEEE, PRISM-II, Spectrum24 802.11DS
1437 device rtw # RealTek 8180
1438 # Requires wlan_ratectl_onoe and wlan_wep
1439 device acx # TI ACX100/ACX111.
1440 # Requires wlan_ratectl_amrr and
1442 device wl0 at isa? port 0x300 # T1 speed ISA/radio lan
1443 device xe # Xircom PCMCIA
1444 device ray # Raytheon Raylink/Webgear Aviator
1445 device ral # Ralink Technology 802.11 wireless NIC
1446 # Requires wlan_ratectl_onoe and
1447 # wlan_ratectl_sample
1449 device oltr0 at isa?
1452 # ATM related options
1454 # The `en' device provides support for Efficient Networks (ENI)
1455 # ENI-155 PCI midway cards, and the Adaptec 155Mbps PCI ATM cards (ANA-59x0).
1457 # atm pseudo-device provides generic atm functions and is required for
1459 # NATM enables the netnatm protocol family that can be used to
1462 # the current driver supports only PVC operations (no atm-arp, no multicast).
1463 # for more details, please read the original documents at
1464 # http://www.ccrc.wustl.edu/pub/chuck/tech/bsdatm/bsdatm.html
1468 options NATM #native ATM
1472 # The flags of the device tells the device a bit more info about the
1473 # device that normally is obtained through the PnP interface.
1474 # bit 2..0 secondary DMA channel;
1475 # bit 4 set if the board uses two dma channels;
1476 # bit 15..8 board type, overrides autodetection; leave it
1477 # zero if don't know what to put in (and you don't,
1478 # since this is unsupported at the moment...).
1480 # This driver will use the new PnP code if it's available. You might
1481 # need PNPBIOS for ISA devices.
1483 # If you have a GUS-MAX card and want to use the CS4231 codec on the
1484 # card the drqs for the gus max must be 8 bit (1, 2, or 3).
1486 # If you would like to use the full duplex option on the gus, then define
1487 # flags to be the ``read dma channel''.
1490 # Basic sound card support:
1492 # For PnP/PCI sound cards:
1494 device "snd_als4000"
1500 device "snd_emu10k1"
1506 device "snd_maestro"
1507 device "snd_maestro3"
1509 device "snd_neomagic"
1514 device "snd_t4dwave"
1515 device "snd_via8233"
1516 device "snd_via82c686"
1518 # For non-pnp sound cards:
1519 device pcm0 at isa? irq 10 drq 1 flags 0x0
1524 # Miscellaneous hardware:
1526 # wt: Wangtek and Archive QIC-02/QIC-36 tape drives
1527 # ctx: Cortex-I frame grabber
1528 # apm: Laptop Advanced Power Management (experimental)
1529 # spigot: The Creative Labs Video Spigot video-acquisition board
1530 # meteor: Matrox Meteor video capture board
1531 # bktr: Brooktree bt848/848a/849a/878/879 video capture and TV Tuner board
1532 # cy: Cyclades serial driver
1533 # dgb: Digiboard PC/Xi and PC/Xe series driver (ALPHA QUALITY!)
1534 # dgm: Digiboard PC/Xem driver
1535 # gp: National Instruments AT-GPIB and AT-GPIB/TNT board
1536 # asc: GI1904-based hand scanners, e.g. the Trust Amiscan Grey
1537 # gsc: Genius GS-4500 hand scanner.
1539 # labpc: National Instrument's Lab-PC and Lab-PC+
1540 # rc: RISCom/8 multiport card
1541 # rp: Comtrol Rocketport(ISA) - single card
1542 # tw: TW-523 power line interface for use with X-10 home control products
1543 # si: Specialix SI/XIO 4-32 port terminal multiplexor
1544 # spic: Sony Programmable I/O controller (VAIO notebooks)
1545 # stl: Stallion EasyIO and EasyConnection 8/32 (ISA and PCI), EasyConnection 8/64 PCI
1546 # stli: Stallion EasyConnection 8/64 ISA/EISA, ONboard, Brumby (intelligent)
1547 # nmdm: nullmodem terminal driver (see nmdm(4))
1550 # The flags takes the following meaning for apm0:
1551 # 0x0020 Statclock is broken.
1552 # If apm is omitted, some systems require sysctl -w kern.timecounter.method=1
1553 # for correct timekeeping.
1555 # Notes on the spigot:
1556 # The video spigot is at 0xad6. This port address can not be changed.
1557 # The irq values may only be 10, 11, or 15
1558 # I/O memory is an 8kb region. Possible values are:
1559 # 0a0000, 0a2000, ..., 0fffff, f00000, f02000, ..., ffffff
1560 # The start address must be on an even boundary.
1561 # Add the following option if you want to allow non-root users to be able
1562 # to access the spigot. This option is not secure because it allows users
1563 # direct access to the I/O page.
1564 # options SPIGOT_UNSECURE
1566 # Notes on the Comtrol Rocketport driver:
1568 # The exact values used for rp0 depend on how many boards you have
1569 # in the system. The manufacturer's sample configs are listed as:
1571 # Comtrol Rocketport ISA single card
1572 # device rp0 at isa? port 0x280
1574 # If instead you have two ISA cards, one installed at 0x100 and the
1575 # second installed at 0x180, then you should add the following to
1576 # your kernel configuration file:
1578 # device rp0 at isa? port 0x100
1579 # device rp1 at isa? port 0x180
1581 # For 4 ISA cards, it might be something like this:
1583 # device rp0 at isa? port 0x180
1584 # device rp1 at isa? port 0x100
1585 # device rp2 at isa? port 0x340
1586 # device rp3 at isa? port 0x240
1588 # And for PCI cards, you only need say:
1592 # Notes on the Digiboard driver:
1594 # The following flag values have special meanings:
1595 # 0x01 - alternate layout of pins (dgb & dgm)
1596 # 0x02 - use the windowed PC/Xe in 64K mode (dgb only)
1598 # Notes on the Specialix SI/XIO driver:
1599 # **This is NOT a Specialix supported Driver!**
1600 # The host card is memory, not IO mapped.
1601 # The Rev 1 host cards use a 64K chunk, on a 32K boundary.
1602 # The Rev 2 host cards use a 32K chunk, on a 32K boundary.
1603 # The cards can use an IRQ of 11, 12 or 15.
1605 # Notes on the Stallion stl and stli drivers:
1606 # See src/i386/isa/README.stl for complete instructions.
1607 # This is version 2.0.0, unsupported by Stallion.
1608 # The stl driver has a secondary IO port hard coded at 0x280. You need
1609 # to change src/i386/isa/stallion.c if you reconfigure this on the boards.
1610 # The "flags" and "iosiz" settings on the stli driver depend on the board:
1611 # EasyConnection 8/64 ISA: flags 23 iosiz 0x1000
1612 # EasyConnection 8/64 EISA: flags 24 iosiz 0x10000
1613 # ONboard ISA: flags 4 iosiz 0x10000
1614 # ONboard EISA: flags 7 iosiz 0x10000
1615 # Brumby: flags 2 iosiz 0x4000
1616 # Stallion: flags 1 iosiz 0x10000
1617 # For the PCI cards, "device stl" will suffice.
1619 # for the SoundBlaster 16 multicd - up to 4 devices
1620 device wt0 at isa? port 0x300 irq 5 drq 1
1621 device ctx0 at isa? port 0x230 iomem 0xd0000
1622 device spigot0 at isa? port 0xad6 irq 15 iomem 0xee000
1624 device gp0 at isa? port 0x2c0
1625 device gsc0 at isa? port IO_GSC1 drq 3
1626 device joy0 at isa? port IO_GAME
1627 device cy0 at isa? irq 10 iomem 0xd4000 iosiz 0x2000
1628 options CY_PCI_FASTINTR # Use with cy_pci unless irq is shared
1629 #device dgb0 at isa? port 0x220 iomem 0xfc000
1630 #options NDGBPORTS=16 # Defaults to 16*NDGB
1631 device dgm0 at isa? port 0x104 iomem 0xd0000
1632 device labpc0 at isa? port 0x260 irq 5
1633 device rc0 at isa? port 0x220 irq 12
1635 #device rp0 at isa? port 0x280
1636 # the port and irq for tw0 are fictitious
1637 device tw0 at isa? port 0x380 irq 11
1638 device si0 at isa? iomem 0xd0000 irq 12
1639 device asc0 at isa? port IO_ASC1 drq 3 irq 10
1640 device spic0 at isa? irq 0 port 0x10a0
1641 device stl0 at isa? port 0x2a0 irq 10
1642 device stli0 at isa? port 0x2a0 iomem 0xcc000 flags 23 iosiz 0x1000
1643 # HOT1 Xilinx 6200 card (http://www.vcc.com/)
1645 # nullmodem terminal driver
1651 # The EISA bus device is `eisa'. It provides auto-detection and
1652 # configuration support for all devices on the EISA bus.
1654 # The `ahb' device provides support for the Adaptec 174X adapter.
1656 # The `ahc' device provides support for the Adaptec 274X and 284X
1657 # adapters. The 284X, although a VLB card, responds to EISA probes.
1659 # fea: DEC DEFEA EISA FDDI adapter
1666 # The aic7xxx driver will attempt to use memory mapped I/O for all PCI
1667 # controllers that have it configured only if this option is set. Unfortunately,
1668 # this doesn't work on some motherboards, which prevents it from being the
1670 options AHC_ALLOW_MEMIO
1672 # The adw driver will attempt to use memory mapped I/O for all PCI
1673 # controllers that have it configured only if this option is set.
1674 options ADW_ALLOW_MEMIO
1676 # By default, only 10 EISA slots are probed, since the slot numbers
1677 # above clash with the configuration address space of the PCI subsystem,
1678 # and the EISA probe is not very smart about this. This is sufficient
1679 # for most machines, but in particular the HP NetServer LC series comes
1680 # with an onboard AIC7770 dual-channel SCSI controller on EISA slot #11,
1681 # thus you need to bump this figure to 12 for them.
1682 options EISA_SLOTS=12
1685 # PCI devices & PCI options:
1687 # The main PCI bus device is `pci'. It provides auto-detection and
1688 # configuration support for all devices on the PCI bus, using either
1689 # configuration mode defined in the PCI specification.
1695 #Enable pci resources left off by a "lazy" BIOS.
1697 #WARNING! PCI_ENABLE_IO_MODES IS A VERY DANGEROUS OPTION AND MANY
1698 #SYSTEMS WILL EXPERIENCE INSTABILITY WITH IT ON. USE ONLY AS A LAST
1701 options PCI_ENABLE_IO_MODES
1702 #options PCI_QUIET #quiets PCI code on chipset settings
1703 options COMPAT_OLDPCI #FreeBSD 2.2 and 3.x compatibility shims
1704 #options PCI_MAP_FIXUP #fixup lazy PCI mappings for certain devices,
1705 #e.g. ATA controllers in legacy mode. NATA
1706 #requires this, don't use it with old ATA!
1713 # The `ahc' device provides support for the Adaptec 29/3940(U)(W)
1714 # and motherboard based AIC7870/AIC7880 adapters.
1716 options AHC_DEBUG_OPTS=0xffffffff
1717 options AHC_REG_PRETTY_PRINT
1718 options AHC_TMODE_ENABLE
1720 # The 'ahd' device provides support for the Adaptec 79xx Ultra320
1721 # SCSI adapters. Options are documented in the ahd(4) manpage:
1723 options AHD_DEBUG_OPTS=0xffffffff
1724 options AHD_REG_PRETTY_PRINT
1725 #options AHD_TMODE_ENABLE=0xff
1727 # The `amd' device provides support for the AMD 53C974 SCSI host
1728 # adapter chip as found on devices such as the Tekram DC-390(T).
1730 # The `bge' device provides support for gigabit ethernet adapters
1731 # based on the Broadcom BCM570x family of controllers, including the
1732 # 3Com 3c996-T, the Netgear GA302T, the SysKonnect SK-9D21 and SK-9D41,
1733 # and the embedded gigE NICs on Dell PowerEdge 2550 servers.
1735 # The `ncr' device provides support for the NCR 53C810 and 53C825
1736 # self-contained SCSI host adapters.
1738 # The `isp' device provides support for the Qlogic ISP 1020, 1040
1739 # nd 1040B PCI SCSI host adapters, ISP 1240 Dual Ultra SCSI,
1740 # ISP 1080 and 1280 (Dual) Ultra2, ISP 12160 Ultra3 SCSI, as well as
1741 # the Qlogic ISP 2100 and ISP 2200 Fibre Channel Host Adapters.
1743 # The `dc' device provides support for PCI fast ethernet adapters
1744 # based on the DEC/Intel 21143 and various workalikes including:
1745 # the ADMtek AL981 Comet and AN985 Centaur, the ASIX Electronics
1746 # AX88140A and AX88141, the Davicom DM9100 and DM9102, the Lite-On
1747 # 82c168 and 82c169 PNIC, the Lite-On/Macronix LC82C115 PNIC II
1748 # and the Macronix 98713/98713A/98715/98715A/98725 PMAC. This driver
1749 # replaces the old al, ax, dm, pn and mx drivers. List of brands:
1750 # Digital DE500-BA, Kingston KNE100TX, D-Link DFE-570TX, SOHOware SFA110,
1751 # SVEC PN102-TX, CNet Pro110B, 120A, and 120B, Compex RL100-TX,
1752 # LinkSys LNE100TX, LNE100TX V2.0, Jaton XpressNet, Alfa Inc GFC2204,
1755 # The `de' device provides support for the Digital Equipment DC21040
1756 # self-contained Ethernet adapter.
1758 # The `em' device provides support for the Intel Pro/1000 Family of Gigabit
1759 # adapters (82542, 82543, 82544, 82540).
1761 # The `fxp' device provides support for the Intel EtherExpress Pro/100B
1762 # PCI Fast Ethernet adapters.
1764 # The `gx' device provides support for the Intel Pro/1000 Gigabit Ethernet
1765 # PCI adapters (82542, 82543-F, 82543-T).
1767 # The 'lge' device provides support for PCI gigabit ethernet adapters
1768 # based on the Level 1 LXT1001 NetCellerator chipset. This includes the
1769 # D-Link DGE-500SX, SMC TigerCard 1000 (SMC9462SX), and some Addtron cards.
1771 # The 'my' device provides support for the Myson MTD80X and MTD89X PCI
1772 # Fast Ethernet adapters.
1774 # The 'nge' device provides support for PCI gigabit ethernet adapters
1775 # based on the National Semiconductor DP83820 and DP83821 chipset. This
1776 # includes the SMC EZ Card 1000 (SMC9462TX), D-Link DGE-500T, Asante
1777 # FriendlyNet GigaNIX 1000TA and 1000TPC, the Addtron AEG320T, the
1778 # LinkSys EG1032 and EG1064, the Surecom EP-320G-TX and the Netgear GA622T.
1780 # The 'pcn' device provides support for PCI fast ethernet adapters based
1781 # on the AMD Am79c97x chipsets, including the PCnet/FAST, PCnet/FAST+,
1782 # PCnet/PRO and PCnet/Home. These were previously handled by the lnc
1783 # driver (and still will be if you leave this driver out of the kernel).
1785 # Te 're' device provides support for PCI GigaBit ethernet adapters based
1786 # on the RealTek 8169 chipset. It also supports the 8139C+ and is the
1787 # preferred driver for that chip.
1789 # The 'rl' device provides support for PCI fast ethernet adapters based
1790 # on the RealTek 8129/8139 chipset. Note that the RealTek driver defaults
1791 # to using programmed I/O to do register accesses because memory mapped
1792 # mode seems to cause severe lockups on SMP hardware. This driver also
1793 # supports the Accton EN1207D `Cheetah' adapter, which uses a chip called
1794 # the MPX 5030/5038, which is either a RealTek in disguise or a RealTek
1795 # workalike. Note that the D-Link DFE-530TX+ uses the RealTek chipset
1796 # and is supported by this driver, not the 'vr' driver.
1798 # The 'sf' device provides support for Adaptec Duralink PCI fast
1799 # ethernet adapters based on the Adaptec AIC-6915 "starfire" controller.
1800 # This includes dual and quad port cards, as well as one 100baseFX card.
1801 # Most of these are 64-bit PCI devices, except for one single port
1802 # card which is 32-bit.
1804 # The 'ste' device provides support for adapters based on the Sundance
1805 # Technologies ST201 PCI fast ethernet controller. This includes the
1808 # The 'sis' device provides support for adapters based on the Silicon
1809 # Integrated Systems SiS 900 and SiS 7016 PCI fast ethernet controller
1812 # The 'sk' device provides support for the SysKonnect SK-984x series
1813 # PCI gigabit ethernet NICs. This includes the SK-9841 and SK-9842
1814 # single port cards (single mode and multimode fiber) and the
1815 # SK-9843 and SK-9844 dual port cards (also single mode and multimode).
1816 # The driver will autodetect the number of ports on the card and
1817 # attach each one as a separate network interface.
1819 # The 'ti' device provides support for PCI gigabit ethernet NICs based
1820 # on the Alteon Networks Tigon 1 and Tigon 2 chipsets. This includes the
1821 # Alteon AceNIC, the 3Com 3c985, the Netgear GA620 and various others.
1822 # Note that you will probably want to bump up NMBCLUSTERS a lot to use
1825 # The 'tl' device provides support for the Texas Instruments TNETE100
1826 # series 'ThunderLAN' cards and integrated ethernet controllers. This
1827 # includes several Compaq Netelligent 10/100 cards and the built-in
1828 # ethernet controllers in several Compaq Prosignia, Proliant and
1829 # Deskpro systems. It also supports several Olicom 10Mbps and 10/100
1832 # The `tx' device provides support for the SMC 9432 TX, BTX and FTX cards.
1834 # The `txp' device provides support for the 3Com 3cR990 "Typhoon"
1837 # The `vr' device provides support for various fast ethernet adapters
1838 # based on the VIA Technologies VT3043 `Rhine I' and VT86C100A `Rhine II'
1839 # chips, including the D-Link DFE530TX (see 'rl' for DFE530TX+), the Hawking
1840 # Technologies PN102TX, and the AOpen/Acer ALN-320.
1842 # The `vx' device provides support for the 3Com 3C590 and 3C595
1845 # The `wb' device provides support for various fast ethernet adapters
1846 # based on the Winbond W89C840F chip. Note: this is not the same as
1847 # the Winbond W89C940F, which is an NE2000 clone.
1849 # The `xl' device provides support for the 3Com 3c900, 3c905 and
1850 # 3c905B (Fast) Etherlink XL cards and integrated controllers. This
1851 # includes the integrated 3c905B-TX chips in certain Dell Optiplex and
1852 # Dell Precision desktop machines and the integrated 3c905-TX chips
1853 # in Dell Latitude laptop docking stations.
1855 # The `fpa' device provides support for the Digital DEFPA PCI FDDI
1856 # adapter. pseudo-device fddi is also needed.
1858 # The `meteor' device is a PCI video capture board. It can also have the
1859 # following options:
1860 # options METEOR_ALLOC_PAGES=xxx preallocate kernel pages for data entry
1861 # figure (ROWS*COLUMN*BYTES_PER_PIXEL*FRAME+PAGE_SIZE-1)/PAGE_SIZE
1862 # options METEOR_DEALLOC_PAGES remove all allocated pages on close(2)
1863 # options METEOR_DEALLOC_ABOVE=xxx remove all allocated pages above the
1864 # specified amount. If this value is below the allocated amount no action
1866 # options METEOR_SYSTEM_DEFAULT={METEOR_PAL|METEOR_NTSC|METEOR_SECAM}, used
1867 # for initialization of fps routine when a signal is not present.
1869 # The 'bktr' device is a PCI video capture device using the Brooktree
1870 # bt848/bt848a/bt849a/bt878/bt879 chipset. When used with a TV Tuner it forms a
1871 # TV card, eg Miro PC/TV, Hauppauge WinCast/TV WinTV, VideoLogic Captivator,
1872 # Intel Smart Video III, AverMedia, IMS Turbo, FlyVideo.
1874 # options OVERRIDE_CARD=xxx
1875 # options OVERRIDE_TUNER=xxx
1876 # options OVERRIDE_MSP=1
1877 # options OVERRIDE_DBX=1
1878 # These options can be used to override the auto detection
1879 # The current values for xxx are found in src/sys/dev/bktr/bktr_card.h
1880 # Using sysctl(8) run-time overrides on a per-card basis can be made
1882 # options BKTR_SYSTEM_DEFAULT=BROOKTREE_PAL
1884 # options BKTR_SYSTEM_DEFAULT=BROOKTREE_NTSC
1885 # Specifes the default video capture mode.
1886 # This is required for Dual Crystal (28&35Mhz) boards where PAL is used
1887 # to prevent hangs during initialisation. eg VideoLogic Captivator PCI.
1889 # options BKTR_USE_PLL
1890 # PAL or SECAM users who have a 28Mhz crystal (and no 35Mhz crystal)
1891 # must enable PLL mode with this option. eg some new Bt878 cards.
1893 # options BKTR_GPIO_ACCESS
1894 # This enable IOCTLs which give user level access to the GPIO port.
1896 # options BKTR_NO_MSP_RESET
1897 # Prevents the MSP34xx reset. Good if you initialise the MSP in another OS first
1899 # options BKTR_430_FX_MODE
1900 # Switch Bt878/879 cards into Intel 430FX chipset compatibility mode.
1902 # options BKTR_SIS_VIA_MODE
1903 # Switch Bt878/879 cards into SIS/VIA chipset compatibility mode which is
1904 # needed for some old SiS and VIA chipset motherboards.
1905 # This also allows Bt878/879 chips to work on old OPTi (<1997) chipset
1906 # motherboards and motherboards with bad or incomplete PCI 2.1 support.
1907 # As a rough guess, old = before 1998
1909 # options BKTR_NEW_MSP34XX_DRIVER
1910 # Use new, more complete initialization scheme for the msp34* soundchip.
1911 # Should fix stereo autodetection if the old driver does only output
1914 # options BKTR_OVERRIDE_CARD=xxx
1915 # options BKTR_OVERRIDE_DBX=xxx
1916 # options BKTR_OVERRIDE_MSP=xxx
1917 # options BKTR_OVERRIDE_TUNER=xxx
1918 # These options can be used to select a specific device, regardless of
1919 # the autodetection and i2c device checks (see comments in bktr_card.c).
1922 # The oltr driver supports the following Olicom PCI token-ring adapters
1923 # OC-3136, OC-3137, OC-3139, OC-3140, OC-3141, OC-3540, OC-3250
1925 device ahc # AHA2940 and onboard AIC7xxx devices
1926 device ahd # AIC79xx devices
1927 device amd # AMD 53C974 (Tekram DC-390(T))
1928 device isp # Qlogic family
1929 device ispfw # Firmware for QLogic HBAs
1930 device mpt # LSI '909 FC adapters
1931 device ncr # NCR/Symbios Logic
1932 device sym # NCR/Symbios Logic (newer chipsets)
1933 device trm # Tekram DC395U/UW/F and DC315U
1937 # ISP_TARGET_MODE - enable target mode operation
1938 #options ISP_TARGET_MODE=1
1940 # Options used in dev/sym/ (Symbios SCSI driver).
1941 #options SYM_SETUP_LP_PROBE_MAP #-Low Priority Probe Map (bits)
1942 # Allows the ncr to take precedence
1943 # 1 (1<<0) -> 810a, 860
1944 # 2 (1<<1) -> 825a, 875, 885, 895
1945 # 4 (1<<2) -> 895a, 896, 1510d
1946 #options SYM_SETUP_SCSI_DIFF #-HVD support for 825a, 875, 885
1947 # disabled:0 (default), enabled:1
1948 #options SYM_SETUP_PCI_PARITY #-PCI parity checking
1949 # disabled:0, enabled:1 (default)
1950 #options SYM_SETUP_MAX_LUN #-Number of LUNs supported
1951 # default:8, range:[1..64]
1954 # MII bus support is required for some PCI 10/100 ethernet NICs,
1955 # namely those which use MII-compliant transceivers or implement
1956 # transceiver control interfaces that operate like an MII. Adding
1957 # "device miibus0" to the kernel config pulls in support for
1958 # the generic miibus API and all of the PHY drivers, including a
1959 # generic one for PHYs that aren't specifically handled by an
1960 # individual driver.
1963 # PCI Ethernet NICs that use the common MII bus controller code.
1964 device bce # Broadcom NetXtreme II Gigabit Ethernet
1965 device bfe # Broadcom BCM440x 10/100 Ethernet
1966 device dc # DEC/Intel 21143 and various workalikes
1967 device fxp # Intel EtherExpress PRO/100B (82557, 82558)
1968 device my # Myson Fast Ethernet (MTD80X, MTD89X)
1969 device pcn # AMD Am79C97x PCI 10/100 NICs
1970 device re # RealTek 8139C+/8169
1971 device rl # RealTek 8129/8139
1972 device sbsh # Granch SBNI16 SHDSL modem
1973 device sf # Adaptec AIC-6915 (``Starfire'')
1974 device sis # Silicon Integrated Systems SiS 900/SiS 7016
1975 device ste # Sundance ST201 (D-Link DFE-550TX)
1976 device tl # Texas Instruments ThunderLAN
1977 device tx # SMC EtherPower II (83c17x ``EPIC'')
1978 device vge # VIA 612x GigE
1979 device vr # VIA Rhine, Rhine II
1980 device wb # Winbond W89C840F
1981 device xl # 3Com 3c90x (``Boomerang'', ``Cyclone'')
1983 # PCI Ethernet NICs.
1984 device de # DEC/Intel DC21x4x (``Tulip'')
1985 device txp # 3Com 3cR990 (``Typhoon'')
1986 device vx # 3Com 3c590, 3c595 (``Vortex'')
1988 # Gigabit Ethernet NICs.
1989 device bge # Broadcom BCM570x (``Tigon III'')
1990 device em # Intel Pro/1000 (82542,82543,82544,82540)
1991 device gx # Intel Pro/1000 (82542, 82543)
1992 device lge # Level 1 LXT1001 (``Mercury'')
1993 device nfe # nVidia nForce2/3 MCP04/51/55 CK804
1994 device nge # NatSemi DP83820 and DP83821
1995 device sk # SysKonnect GEnesis, LinkSys EG1023, D-Link
1996 device ti # Alteon (``Tigon I'', ``Tigon II'')
1997 device stge # Sundance/Tamarack TC9021 Gigabit Ethernet
2002 #The oltr driver in the ISA section will also find PCI cards.
2006 # Brooktree driver has been ported to the new I2C framework. Thus,
2007 # you'll need to have the following 3 lines in the kernel config.
2011 # The iic and smb devices are only needed if you want to control other
2012 # I2C slaves connected to the external connector of some cards.
2015 options BKTR_NEW_MSP34XX_DRIVER
2020 # pccard: pccard slots
2021 # cardbus/cbb: cardbus bridge
2027 # Laptop/Notebook options:
2030 # apm under `Miscellaneous hardware'
2033 # For older notebooks that signal a powerfail condition (external
2034 # power supply dropped, or battery state low) by issuing an NMI:
2036 options POWERFAIL_NMI # make it beep instead of panicing
2041 # System Management Bus support is provided by the 'smbus' device.
2042 # Access to the SMBus device is via the 'smb' device (/dev/smb*),
2043 # which is a child of the 'smbus' device.
2045 # Supported devices:
2046 # smb standard io through /dev/smb*
2048 # Supported SMB interfaces:
2049 # iicsmb I2C to SMB bridge with any iicbus interface
2050 # bktr brooktree848 I2C hardware interface
2051 # intpm Intel PIIX4 (82371AB, 82443MX) Power Management Unit
2052 # alpm Acer Aladdin-IV/V/Pro2 Power Management Unit
2053 # ichsmb Intel ICH SMBus controller chips (82801AA, 82801AB, 82801BA)
2054 # viapm VIA VT82C586B,596,686A and VT8233 SMBus controllers
2055 # amdpm AMD 756 Power Management Unit
2057 device smbus # Bus support, required for smb below.
2070 # Philips i2c bus support is provided by the `iicbus' device.
2072 # Supported devices:
2073 # ic i2c network interface
2074 # iic i2c standard io
2075 # iicsmb i2c to smb bridge. Allow i2c i/o with smb commands.
2077 # Supported interfaces:
2078 # pcf Philips PCF8584 ISA-bus controller
2079 # bktr brooktree848 I2C software interface
2082 # iicbb generic I2C bit-banging code (needed by lpbb, bktr)
2084 device iicbus # Bus support, required for ic/iic/iicsmb below.
2089 device iicsmb # smb over i2c bridge
2091 device pcf0 at isa? port 0x320 irq 5
2093 #---------------------------------------------------------------------------
2096 # See /usr/share/examples/isdn/ROADMAP for an introduction to isdn4bsd.
2098 # i4b passive ISDN cards support contains the following hardware drivers:
2100 # isic - Siemens/Infineon ISDN ISAC/HSCX/IPAC chipset driver
2101 # iwic - Winbond W6692 PCI bus ISDN S/T interface controller
2102 # ifpi - AVM Fritz!Card PCI driver
2103 # ifpi2 - AVM Fritz!Card PCI driver Version 2
2104 # ihfc - Cologne Chip HFC ISA/ISA-PnP chipset driver
2105 # ifpnp - AVM Fritz!Card PnP driver
2106 # itjc - Siemens ISAC / TJNet Tiger300/320 chipset
2108 # i4b active ISDN cards support contains the following hardware drivers:
2110 # iavc - AVM B1 PCI, AVM B1 ISA, AVM T1
2112 # Note that the ``options'' (if given) and ``device'' lines must BOTH
2113 # be uncommented to enable support for a given card !
2115 # In addition to a hardware driver (and probably an option) the mandatory
2116 # ISDN protocol stack devices and the mandatory support device must be
2117 # enabled as well as one or more devices from the optional devices section.
2119 #---------------------------------------------------------------------------
2120 # isic driver (Siemens/Infineon chipsets)
2121 #---------------------------------------------------------------------------
2123 # ISA bus non-PnP Cards:
2124 # ----------------------
2126 # Teles S0/8 or Niccy 1008
2128 device isic0 at isa? iomem 0xd0000 irq 5 flags 1
2130 # Teles S0/16 or Creatix ISDN-S0 or Niccy 1016
2132 #device isic0 at isa? port 0xd80 iomem 0xd0000 irq 5 flags 2
2136 #device isic0 at isa? port 0xd80 irq 5 flags 3
2138 # AVM A1 or AVM Fritz!Card
2140 #device isic0 at isa? port 0x340 irq 5 flags 4
2142 # USRobotics Sportster ISDN TA intern
2144 #device isic0 at isa? port 0x268 irq 5 flags 7
2146 # ITK ix1 Micro ( < V.3, non-PnP version )
2148 #device isic0 at isa? port 0x398 irq 10 flags 18
2152 #device isic0 at isa? port 0x360 irq 10 flags 20
2154 # ISA bus PnP Cards:
2155 # ------------------
2158 options TEL_S0_16_3_P
2161 # Creatix ISDN-S0 P&P
2165 # Dr. Neuhaus Niccy Go@
2169 # Sedlbauer Win Speed
2177 # ELSA QuickStep 1000pro ISA
2181 # ITK ix1 Micro ( V.3, PnP version )
2185 # Siemens I-Surf 2.0
2186 options SIEMENS_ISURF2
2189 # Asuscom ISDNlink 128K ISAC
2190 options ASUSCOM_IPAC
2193 # Eicon Diehl DIVA 2.0 and 2.02
2197 # Compaq Microcom 610
2204 # ELSA MicroLink ISDN/PCI (same as ELSA QuickStep 1000pro PCI)
2208 #---------------------------------------------------------------------------
2209 # ifpnp driver for AVM Fritz!Card ISA PnP
2210 #---------------------------------------------------------------------------
2212 # AVM Fritz!Card ISA PnP
2215 #---------------------------------------------------------------------------
2216 # ihfc driver for Cologne Chip ISA chipsets (experimental!)
2217 #---------------------------------------------------------------------------
2219 # Teles 16.3c ISA PnP
2220 # AcerISDN P10 ISA PnP
2221 # TELEINT ISDN SPEED No.1
2224 #---------------------------------------------------------------------------
2225 # ifpi driver for AVM Fritz!Card PCI 1.0 (2.0 unsupported!)
2226 #---------------------------------------------------------------------------
2228 # AVM Fritz!Card PCI 1.0
2231 #---------------------------------------------------------------------------
2232 # ifpi2 driver for AVM Fritz!Card PCI 2.0
2233 #---------------------------------------------------------------------------
2235 # AVM Fritz!Card PCI 2.0
2238 #---------------------------------------------------------------------------
2239 # iwic driver for Winbond W6692 chipset
2240 #---------------------------------------------------------------------------
2242 # ASUSCOM P-IN100-ST-D (and other Winbond W6692 based cards)
2245 #---------------------------------------------------------------------------
2246 # itjc driver for Siemens ISAC / TJNet Tiger300/320 chipset
2247 #---------------------------------------------------------------------------
2249 # Traverse Technologies NETjet-S
2253 #---------------------------------------------------------------------------
2254 # iavc driver (AVM active cards, needs i4bcapi driver!)
2255 #---------------------------------------------------------------------------
2257 pseudo-device "i4bcapi" 2
2262 # AVM B1 ISA bus (PnP mode not supported!)
2263 #device iavc0 at isa? port 0x150 irq 5
2266 # ISDN Protocol Stack (mandatory)
2267 # -------------------------------
2269 # Q.921 / layer 2 - i4b passive cards D channel handling
2270 pseudo-device "i4bq921"
2272 # Q.931 / layer 3 - i4b passive cards D channel handling
2273 pseudo-device "i4bq931"
2275 # layer 4 - i4b common passive and active card handling
2281 # userland driver to do ISDN tracing (for passive cards only)
2282 pseudo-device "i4btrc" 4
2284 # userland driver to control the whole thing (mandatory)
2285 pseudo-device "i4bctl"
2287 # userland driver for access to raw B channel
2288 pseudo-device "i4brbch" 4
2290 # userland driver for telephony
2291 pseudo-device "i4btel" 2
2293 # network driver for IP over raw HDLC ISDN
2294 pseudo-device "i4bipr" 4
2295 # enable VJ header compression detection for ipr i/f
2297 # enable logging of the first n IP packets to isdnd (n=32 here)
2300 # network driver for sync PPP over ISDN - requires sppp
2301 pseudo-device "i4bisppp" 4
2306 # Parallel port bus support is provided by the `ppbus' device.
2307 # Multiple devices may be attached to the parallel port, devices
2308 # are automatically probed and attached when found.
2310 # Supported devices:
2311 # vpo Iomega Zip Drive
2312 # Requires SCSI disk support ('scbus' and 'da'); the best
2313 # performance is achieved with ports in EPP 1.9 mode.
2314 # lpt Parallel Printer
2315 # plip Parallel network interface
2316 # ppi General-purpose I/O ("Geek Port") + IEEE1284 I/O
2317 # pps Pulse per second Timing Interface
2318 # lpbb Philips official parallel port I2C bit-banging interface
2320 # Supported interfaces:
2321 # ppc ISA-bus parallel port interfaces.
2324 options PPC_PROBE_CHIPSET # Enable chipset specific detection
2325 # (see flags in ppc(4))
2326 options DEBUG_1284 # IEEE1284 signaling protocol debug
2327 options PERIPH_1284 # Makes your computer act as a IEEE1284
2328 # compliant peripheral
2329 options DONTPROBE_1284 # Avoid boot detection of PnP parallel devices
2330 options VP0_DEBUG # ZIP/ZIP+ debug
2331 options LPT_DEBUG # Printer driver debug
2332 options PPC_DEBUG=2 # Parallel chipset level debug
2333 options PLIP_DEBUG # Parallel network IP interface debug
2334 options PCFCLOCK_VERBOSE # Verbose pcfclock driver
2335 options PCFCLOCK_MAX_RETRIES=5 # Maximum read tries (default 10)
2337 device ppc0 at isa? irq 7
2347 # Kernel BOOTP support
2349 options BOOTP # Use BOOTP to obtain IP address/hostname
2350 options BOOTP_NFSROOT # NFS mount root filesystem using BOOTP info
2351 options BOOTP_NFSV3 # Use NFS v3 to NFS mount root
2352 options BOOTP_COMPAT # Workaround for broken bootp daemons.
2353 options BOOTP_WIRED_TO=fxp0 # Use interface fxp0 for BOOTP
2356 # Add tie-ins for a hardware watchdog. This only enable the hooks;
2357 # the user must still supply the actual driver.
2362 # Set the number of PV entries per process. Increasing this can
2363 # stop panics related to heavy use of shared memory. However, that can
2364 # (combined with large amounts of physical memory) cause panics at
2365 # boot time due the kernel running out of VM space.
2367 # If you're tweaking this, you might also want to increase the sysctls
2368 # "vm.v_free_min", "vm.v_free_reserved", and "vm.v_free_target".
2370 # The value below is the one more than the default.
2372 options PMAP_SHPGPERPROC=201
2375 # Change the size of the kernel virtual address space. Due to
2376 # constraints in loader(8) on i386, this must be a multiple of 4.
2377 # 256 = 1 GB of kernel address space. Increasing this also causes
2378 # a reduction of the address space in user processes. 512 splits
2379 # the 4GB cpu address space in half (2GB user, 2GB kernel).
2381 options KVA_PAGES=260
2384 # Disable swapping. This option removes all code which actually performs
2385 # swapping, so it's not possible to turn it back on at run-time.
2387 # This is sometimes usable for systems which don't have any swap space
2388 # (see also sysctls "vm.defer_swapspace_pageouts" and
2389 # "vm.disable_swapspace_pageouts")
2391 #options NO_SWAPPING
2393 # Set the number of sf_bufs to allocate. sf_bufs are virtual buffers
2394 # for sendfile(2) that are used to map file VM pages, and normally
2395 # default to a quantity that is roughly 16*MAXUSERS+512. You would
2396 # typically want about 4 of these for each simultaneous file send.
2398 options NSFBUFS=1024
2400 # Set the size of the buffer cache KVM reservation, in buffers. This is
2401 # scaled by approximately 16384 bytes. The system will auto-size the buffer
2402 # cache if this option is not specified.
2406 # Set the size of the mbuf KVM reservation, in clusters. This is scaled
2407 # by approximately 2048 bytes. The system will auto-size the mbuf area
2408 # to (512 + maxusers*16) if this option is not specified.
2409 # maxusers is in turn computed at boot time depending on available memory
2410 # or set to the value specified by "options MAXUSERS=x" (x=0 means
2412 # So, to take advantage of autoscaling, you have to remove both
2413 # NMBCLUSTERS and MAXUSERS (and NMBUFS) from your kernel config.
2415 options NMBCLUSTERS=1024
2417 # Set the number of mbufs available in the system. Each mbuf
2418 # consumes 256 bytes. The system will autosize this (to 4 times
2419 # the number of NMBCLUSTERS, depending on other constraints)
2420 # if this option is not specified.
2424 # Tune the buffer cache maximum KVA reservation, in bytes. The maximum is
2425 # usually capped at 200 MB, effecting machines with > 1GB of ram. Note
2426 # that the buffer cache only really governs write buffering and disk block
2427 # translations. The VM page cache is our primary disk cache and is not
2428 # effected by the size of the buffer cache.
2430 options VM_BCACHE_SIZE_MAX="(100*1024*1024)"
2432 # Tune the swap zone KVA reservation, in bytes. The default is typically
2433 # 70 MB, giving the system the ability to manage a maximum of 28GB worth
2434 # of swapped out data.
2436 options VM_SWZONE_SIZE_MAX="(50*1024*1024)"
2439 # Enable extra debugging code for locks. This stores the filename and
2440 # line of whatever acquired the lock in the lock itself, and change a
2441 # number of function calls to pass around the relevant data. This is
2442 # not at all useful unless you are debugging lock code. Also note
2443 # that it is likely to break e.g. fstat(1) unless you recompile your
2444 # userland with -DDEBUG_LOCKS as well.
2448 # Set the amount of time (in seconds) the system will wait before
2449 # rebooting automatically when a kernel panic occurs. If set to (-1),
2450 # the system will wait indefinitely until a key is pressed on the
2452 options PANIC_REBOOT_WAIT_TIME=16
2454 # Attempt to bypass the buffer cache and put data directly into the
2455 # userland buffer for read operation when O_DIRECT flag is set on the
2456 # file. Both offset and length of the read operation must be
2457 # multiples of the physical media sector size.
2461 # Specify a lower limit for the number of swap I/O buffers. They are
2462 # (among other things) used when bypassing the buffer cache due to
2463 # DIRECTIO kernel option enabled and O_DIRECT flag set on file.
2465 #options NSWBUF_MIN=120
2467 # The 'asr' driver provides support for current DPT/Adaptec SCSI RAID
2468 # controllers (SmartRAID V and VI and later).
2469 # These controllers require the CAM infrastructure.
2473 # The 'dpt' driver provides support for DPT controllers (http://www.dpt.com/).
2474 # These have hardware RAID-{0,1,5} support, and do multi-initiator I/O.
2475 # The DPT controllers are commonly re-licensed under other brand-names -
2476 # some controllers by Olivetti, Dec, HP, AT&T, SNI, AST, Alphatronic, NEC and
2477 # Compaq are actually DPT controllers.
2479 # See src/sys/dev/dpt for debugging and other subtle options.
2480 # DPT_MEASURE_PERFORMANCE Enables a set of (semi)invasive metrics. Various
2481 # instruments are enabled. The tools in
2482 # /usr/sbin/dpt_* assume these to be enabled.
2483 # DPT_HANDLE_TIMEOUTS Normally device timeouts are handled by the DPT.
2484 # If you ant the driver to handle timeouts, enable
2485 # this option. If your system is very busy, this
2486 # option will create more trouble than solve.
2487 # DPT_TIMEOUT_FACTOR Used to compute the excessive amount of time to
2488 # wait when timing out with the above option.
2489 # DPT_DEBUG_xxxx These are controllable from sys/dev/dpt/dpt.h
2490 # DPT_LOST_IRQ When enabled, will try, once per second, to catch
2491 # any interrupt that got lost. Seems to help in some
2492 # DPT-firmware/Motherboard combinations. Minimal
2493 # cost, great benefit.
2494 # DPT_RESET_HBA Make "reset" actually reset the controller
2495 # instead of fudging it. Only enable this if you
2496 # are 100% certain you need it.
2501 #!CAM# options DPT_MEASURE_PERFORMANCE
2502 #!CAM# options DPT_HANDLE_TIMEOUTS
2503 options DPT_TIMEOUT_FACTOR=4
2504 options DPT_LOST_IRQ
2505 options DPT_RESET_HBA
2508 # Compaq "CISS" RAID controllers (SmartRAID 5* series)
2509 # These controllers have a SCSI-like interface, and require the
2510 # CAM infrastructure.
2515 # Intel Integrated RAID controllers.
2516 # This driver was developed and is maintained by Intel. Contacts
2517 # at Intel for this driver are
2518 # "Kannanthanam, Boji T" <boji.t.kannanthanam@intel.com> and
2519 # "Leubner, Achim" <achim.leubner@intel.com>.
2524 # Mylex AcceleRAID and eXtremeRAID controllers with v6 and later
2525 # firmware. These controllers have a SCSI-like interface, and require
2526 # the CAM infrastructure.
2537 # General USB code (mandatory for USB)
2542 # Generic USB device driver
2544 # Human Interface Device (anything with buttons and dials)
2550 # USB Iomega Zip 100 Drive (Requires scbus and da)
2556 # USB Rio (MP3 Player)
2569 # ADMtek USB ethernet. Supports the LinkSys USB100TX,
2570 # the Billionton USB100, the Melco LU-ATX, the D-Link DSB-650TX
2571 # and the SMC 2202USB. Also works with the ADMtek AN986 Pegasus
2575 # ASIX Electronics AX88172 USB 2.0 ethernet driver. Used in the
2576 # LinkSys USB200M and various other adapters.
2579 # CATC USB-EL1201A USB ethernet. Supports the CATC Netmate
2580 # and Netmate II, and the Belkin F5U111.
2583 # Kawasaki LSI ethernet. Supports the LinkSys USB10T,
2584 # Entrega USB-NET-E45, Peracom Ethernet Adapter, the
2585 # 3Com 3c19250, the ADS Technologies USB-10BT, the ATen UC10T,
2586 # the Netgear EA101, the D-Link DSB-650, the SMC 2102USB
2587 # and 2104USB, and the Corega USB-T.
2590 # RealTek 8150 based USB ethernet device:
2592 # GREEN HOUSE GH-USB100B
2593 # Billionton ThumbLAN USBKR2-100B
2596 # USB wireless NICs, requires wlan_ratectl_onoe
2598 # Ralink Technology RT2501USB/RT2601USB
2601 # Ralink Technology RT2500USB
2604 # debugging options for the USB subsystem
2609 options UKBD_DFLT_KEYMAP # specify the built-in keymap
2610 makeoptions UKBD_DFLT_KEYMAP=it.iso
2613 device firewire # Firewire bus code
2614 device sbp # SCSI over Firewire (Requires scbus and da)
2615 device fwe # Ethernet over Firewire (non-standard!)
2617 # dcons support (Dumb Console Device)
2618 device dcons # dumb console driver
2619 device dcons_crom # FireWire attachment
2620 options DCONS_BUF_SIZE=16384 # buffer size
2621 options DCONS_POLL_HZ=100 # polling rate
2622 options DCONS_FORCE_CONSOLE=1 # force to be the primary console
2623 options DCONS_FORCE_GDB=1 # force to be the gdb device
2625 #####################################################################
2628 # This is a port of the openbsd crypto framework. Include this when
2629 # configuring IPsec and when you have a h/w crypto device to accelerate
2630 # user applications that link to openssl.
2632 # Drivers are ports from openbsd with some simple enhancements that have
2633 # been fed back to openbsd (and hopefully will be included).
2635 pseudo-device crypto # core crypto support
2636 pseudo-device cryptodev # /dev/crypto for access to h/w
2638 device rndtest # FIPS 140-2 entropy tester
2640 device hifn # Hifn 7951, 7781, etc.
2641 options HIFN_DEBUG # enable debugging support: hw.hifn.debug
2642 #options HIFN_NO_RNG # for devices without RNG
2643 options HIFN_RNDTEST # enable rndtest support
2645 device ubsec # Broadcom 5501, 5601, 58xx
2646 options UBSEC_DEBUG # enable debugging support: hw.ubsec.debug
2647 #options UBSEC_NO_RNG # for devices without RNG
2648 options UBSEC_RNDTEST # enable rndtest support
2650 device acpi # basic ACPI support
2651 device pmtimer # adjust the system clock after resume
2654 # mgadrm: AGP Matrox G200, G400, G450, G550
2655 # tdfxdrm: 3dfx Voodoo 3/4/5 and Banshee
2656 # r128drm: ATI Rage 128
2657 # radeondrm: ATI Radeon up to 9000/9100
2658 # DRM_DEBUG: include debug printfs, very slow
2660 # mga requires AGP in the kernel, and it is recommended
2661 # for AGP r128 and radeon cards.
2672 # Embedded system options:
2674 # An embedded system might want to run something other than init.
2675 options INIT_PATH="/sbin/init:/stand/sysinstall"
2678 options BUS_DEBUG # enable newbus debugging
2679 options NPX_DEBUG # enable npx debugging (FPU/math emu)
2681 # Record the program counter of the code interrupted by the statistics
2682 # clock interrupt. Use pctrack(8) to dump this information.
2683 options DEBUG_PCTRACK
2685 # More undocumented options for linting.
2686 # Note that documenting these are not considered an affront.
2689 #options ACPI_NO_SEMAPHORES
2690 options ACPI_QUIRK_VMWARE
2691 options AHC_DUMP_EEPROM
2692 #options BKTR_ALLOC_PAGES=xxx
2693 options CAM_DEBUG_DELAY
2694 options CLUSTERDEBUG
2695 options COMPAT_LINUX
2696 options COMPAT_SUNOS
2698 options DEBUG_CRIT_SECTIONS
2699 options DEBUG_INTERRUPTS
2700 options DEVICE_SYSCTLS
2701 #options DISABLE_PSE
2703 options BCE_NVRAM_WRITE_SUPPORT
2704 #options ED_NO_MIIBUS
2705 options ENABLE_ALART
2707 options FB_INSTALL_CDEV
2708 options FE_8BIT_SUPPORT
2709 options I4B_SMP_WORKAROUND
2710 options I586_PMC_GUPROF=0x70000
2712 options KBDIO_DEBUG=10
2713 options KBD_MAXRETRY=4
2714 options KBD_MAXWAIT=6
2715 options KBD_RESETDELAY=201
2716 options KERN_TIMESTAMP
2721 #options MAXFILES=xxx
2722 options METEOR_TEST_VIDEO
2723 options NETATALKDEBUG
2726 options SCSI_NCR_DEBUG
2727 options SCSI_NCR_MAX_SYNC=10000
2728 options SCSI_NCR_MAX_WIDE=1
2729 options SCSI_NCR_MYADDR=7
2730 options SHOW_BUSYBUFS # List buffers that prevent root unmount
2731 options SIMPLELOCK_DEBUG
2733 options SLIP_IFF_OPTS
2734 options SOCKBUF_DEBUG
2735 options TIMER_FREQ="((14318182+6)/12)"
2736 options VFS_BIO_DEBUG
2737 options WI_SYMBOL_FIRMWARE
2741 #options KTR_GIANT_CONTENTION
2742 #options KTR_SPIN_CONTENTION
2746 #options KTR_USB_MEMORY
2748 options KTR_ENTRIES=1024
2749 options KTR_VERBOSE=1
2752 options ALTQ #alternate queueing
2753 options ALTQ_CBQ #class based queueing
2754 options ALTQ_RED #random early detection
2755 options ALTQ_RIO #triple red for diffserv (needs RED)
2756 options ALTQ_HFSC #hierarchical fair service curve
2757 options ALTQ_PRIQ #priority queue
2758 #options ALTQ_NOPCC #don't use processor cycle counter
2759 options ALTQ_DEBUG #for debugging
2760 # you might want to set kernel timer to 1kHz if you use CBQ,
2761 # especially with 100baseT
2767 options SCTP_USE_ADLER32
2768 options SCTP_HIGH_SPEED
2769 options SCTP_STAT_LOGGING
2770 options SCTP_CWND_LOGGING
2771 options SCTP_BLK_LOGGING
2772 options SCTP_STR_LOGGING
2773 options SCTP_FR_LOGGING
2774 options SCTP_MAP_LOGGING