2 * Copyright (c) 2002-2009 Sam Leffler, Errno Consulting
5 * Redistribution and use in source and binary forms, with or without
6 * modification, are permitted provided that the following conditions
8 * 1. Redistributions of source code must retain the above copyright
9 * notice, this list of conditions and the following disclaimer,
10 * without modification.
11 * 2. Redistributions in binary form must reproduce at minimum a disclaimer
12 * similar to the "NO WARRANTY" disclaimer below ("Disclaimer") and any
13 * redistribution must be conditioned upon including a substantially
14 * similar Disclaimer requirement for further binary redistribution.
17 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
18 * ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
19 * LIMITED TO, THE IMPLIED WARRANTIES OF NONINFRINGEMENT, MERCHANTIBILITY
20 * AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL
21 * THE COPYRIGHT HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY,
22 * OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
23 * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
24 * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER
25 * IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
26 * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
27 * THE POSSIBILITY OF SUCH DAMAGES.
29 * $FreeBSD: head/sys/dev/ath/if_ath.c 203751 2010-02-10 11:12:39Z rpaulo $");
33 * Driver for the Atheros Wireless LAN controller.
35 * This software is derived from work of Atsushi Onoe; his contribution
36 * is greatly appreciated.
43 #include <sys/param.h>
44 #include <sys/systm.h>
45 #include <sys/sysctl.h>
47 #include <sys/malloc.h>
49 #include <sys/mutex.h>
50 #include <sys/kernel.h>
51 #include <sys/socket.h>
52 #include <sys/sockio.h>
53 #include <sys/errno.h>
54 #include <sys/callout.h>
56 #include <sys/endian.h>
57 #include <sys/kthread.h>
58 #include <sys/taskqueue.h>
62 #include <net/if_dl.h>
63 #include <net/if_media.h>
64 #include <net/if_types.h>
65 #include <net/if_arp.h>
66 #include <net/if_llc.h>
67 #include <net/ifq_var.h>
69 #include <netproto/802_11/ieee80211_var.h>
70 #include <netproto/802_11/ieee80211_regdomain.h>
71 #ifdef IEEE80211_SUPPORT_SUPERG
72 #include <netproto/802_11/ieee80211_superg.h>
74 #ifdef IEEE80211_SUPPORT_TDMA
75 #include <netproto/802_11/ieee80211_tdma.h>
81 #include <netinet/in.h>
82 #include <netinet/if_ether.h>
85 #include <dev/netif/ath/ath/if_athvar.h>
86 #include <dev/netif/ath/hal/ath_hal/ah_devid.h> /* XXX for softled */
89 #include <dev/netif/ath_tx99/ath_tx99.h>
93 * ATH_BCBUF determines the number of vap's that can transmit
94 * beacons and also (currently) the number of vap's that can
95 * have unique mac addresses/bssid. When staggering beacons
96 * 4 is probably a good max as otherwise the beacons become
97 * very closely spaced and there is limited time for cab q traffic
98 * to go out. You can burst beacons instead but that is not good
99 * for stations in power save and at some point you really want
100 * another radio (and channel).
102 * The limit on the number of mac addresses is tied to our use of
103 * the U/L bit and tracking addresses in a byte; it would be
104 * worthwhile to allow more for applications like proxy sta.
106 CTASSERT(ATH_BCBUF <= 8);
108 /* unaligned little endian access */
109 #define LE_READ_2(p) \
111 ((((u_int8_t *)(p))[0] ) | (((u_int8_t *)(p))[1] << 8)))
112 #define LE_READ_4(p) \
114 ((((u_int8_t *)(p))[0] ) | (((u_int8_t *)(p))[1] << 8) | \
115 (((u_int8_t *)(p))[2] << 16) | (((u_int8_t *)(p))[3] << 24)))
117 static struct ieee80211vap *ath_vap_create(struct ieee80211com *,
118 const char name[IFNAMSIZ], int unit, int opmode,
119 int flags, const uint8_t bssid[IEEE80211_ADDR_LEN],
120 const uint8_t mac[IEEE80211_ADDR_LEN]);
121 static void ath_vap_delete(struct ieee80211vap *);
122 static void ath_init(void *);
123 static void ath_stop_locked(struct ifnet *);
124 static void ath_stop(struct ifnet *);
125 static void ath_start(struct ifnet *);
126 static int ath_reset(struct ifnet *);
127 static int ath_reset_vap(struct ieee80211vap *, u_long);
128 static int ath_media_change(struct ifnet *);
129 static void ath_watchdog_callout(void *);
130 static int ath_ioctl(struct ifnet *, u_long, caddr_t, struct ucred *);
131 static void ath_fatal_proc(void *, int);
132 static void ath_bmiss_vap(struct ieee80211vap *);
133 static void ath_bmiss_task(void *, int);
134 static int ath_keyset(struct ath_softc *, const struct ieee80211_key *,
135 struct ieee80211_node *);
136 static int ath_key_alloc(struct ieee80211vap *,
137 struct ieee80211_key *,
138 ieee80211_keyix *, ieee80211_keyix *);
139 static int ath_key_delete(struct ieee80211vap *,
140 const struct ieee80211_key *);
141 static int ath_key_set(struct ieee80211vap *, const struct ieee80211_key *,
142 const u_int8_t mac[IEEE80211_ADDR_LEN]);
143 static void ath_key_update_begin(struct ieee80211vap *);
144 static void ath_key_update_end(struct ieee80211vap *);
145 static void ath_update_mcast(struct ifnet *);
146 static void ath_update_promisc(struct ifnet *);
147 static void ath_mode_init(struct ath_softc *);
148 static void ath_setslottime(struct ath_softc *);
149 static void ath_updateslot(struct ifnet *);
150 static int ath_beaconq_setup(struct ath_hal *);
151 static int ath_beacon_alloc(struct ath_softc *, struct ieee80211_node *);
152 static void ath_beacon_update(struct ieee80211vap *, int item);
153 static void ath_beacon_setup(struct ath_softc *, struct ath_buf *);
154 static void ath_beacon_proc(void *, int);
155 static struct ath_buf *ath_beacon_generate(struct ath_softc *,
156 struct ieee80211vap *);
157 static void ath_bstuck_task(void *, int);
158 static void ath_beacon_return(struct ath_softc *, struct ath_buf *);
159 static void ath_beacon_free(struct ath_softc *);
160 static void ath_beacon_config(struct ath_softc *, struct ieee80211vap *);
161 static void ath_descdma_cleanup(struct ath_softc *sc,
162 struct ath_descdma *, ath_bufhead *);
163 static int ath_desc_alloc(struct ath_softc *);
164 static void ath_desc_free(struct ath_softc *);
165 static struct ieee80211_node *ath_node_alloc(struct ieee80211vap *,
166 const uint8_t [IEEE80211_ADDR_LEN]);
167 static void ath_node_free(struct ieee80211_node *);
168 static void ath_node_getsignal(const struct ieee80211_node *,
170 static int ath_rxbuf_init(struct ath_softc *, struct ath_buf *);
171 static void ath_recv_mgmt(struct ieee80211_node *ni, struct mbuf *m,
172 int subtype, int rssi, int nf);
173 static void ath_setdefantenna(struct ath_softc *, u_int);
174 static void ath_rx_task(void *, int);
175 static void ath_txq_init(struct ath_softc *sc, struct ath_txq *, int);
176 static struct ath_txq *ath_txq_setup(struct ath_softc*, int qtype, int subtype);
177 static int ath_tx_setup(struct ath_softc *, int, int);
178 static int ath_wme_update(struct ieee80211com *);
179 static void ath_tx_cleanupq(struct ath_softc *, struct ath_txq *);
180 static void ath_tx_cleanup(struct ath_softc *);
181 static void ath_freetx(struct mbuf *);
182 static int ath_tx_start(struct ath_softc *, struct ieee80211_node *,
183 struct ath_buf *, struct mbuf *);
184 static void ath_tx_task_q0(void *, int);
185 static void ath_tx_task_q0123(void *, int);
186 static void ath_tx_task(void *, int);
187 static void ath_tx_draintxq(struct ath_softc *, struct ath_txq *);
188 static int ath_chan_set(struct ath_softc *, struct ieee80211_channel *);
189 static void ath_draintxq(struct ath_softc *);
190 static void ath_stoprecv(struct ath_softc *);
191 static int ath_startrecv(struct ath_softc *);
192 static void ath_chan_change(struct ath_softc *, struct ieee80211_channel *);
193 static void ath_scan_start(struct ieee80211com *);
194 static void ath_scan_end(struct ieee80211com *);
195 static void ath_set_channel(struct ieee80211com *);
196 static void ath_calibrate_callout(void *);
197 static int ath_newstate(struct ieee80211vap *, enum ieee80211_state, int);
198 static void ath_setup_stationkey(struct ieee80211_node *);
199 static void ath_newassoc(struct ieee80211_node *, int);
200 static int ath_setregdomain(struct ieee80211com *,
201 struct ieee80211_regdomain *, int,
202 struct ieee80211_channel []);
203 static void ath_getradiocaps(struct ieee80211com *, int, int *,
204 struct ieee80211_channel []);
205 static int ath_getchannels(struct ath_softc *);
206 static void ath_led_event(struct ath_softc *, int);
208 static int ath_rate_setup(struct ath_softc *, u_int mode);
209 static void ath_setcurmode(struct ath_softc *, enum ieee80211_phymode);
211 static void ath_sysctlattach(struct ath_softc *);
212 static int ath_raw_xmit(struct ieee80211_node *,
213 struct mbuf *, const struct ieee80211_bpf_params *);
214 static void ath_announce(struct ath_softc *);
215 static void ath_sysctl_stats_attach(struct ath_softc *sc);
217 #ifdef IEEE80211_SUPPORT_TDMA
218 static void ath_tdma_settimers(struct ath_softc *sc, u_int32_t nexttbtt,
220 static void ath_tdma_bintvalsetup(struct ath_softc *sc,
221 const struct ieee80211_tdma_state *tdma);
222 static void ath_tdma_config(struct ath_softc *sc, struct ieee80211vap *vap);
223 static void ath_tdma_update(struct ieee80211_node *ni,
224 const struct ieee80211_tdma_param *tdma, int);
225 static void ath_tdma_beacon_send(struct ath_softc *sc,
226 struct ieee80211vap *vap);
229 ath_hal_setcca(struct ath_hal *ah, int ena)
232 * NB: fill me in; this is not provided by default because disabling
233 * CCA in most locales violates regulatory.
238 ath_hal_getcca(struct ath_hal *ah)
241 if (ath_hal_getcapability(ah, HAL_CAP_DIAG, 0, &diag) != HAL_OK)
243 return ((diag & 0x500000) == 0);
246 #define TDMA_EP_MULTIPLIER (1<<10) /* pow2 to optimize out * and / */
247 #define TDMA_LPF_LEN 6
248 #define TDMA_DUMMY_MARKER 0x127
249 #define TDMA_EP_MUL(x, mul) ((x) * (mul))
250 #define TDMA_IN(x) (TDMA_EP_MUL((x), TDMA_EP_MULTIPLIER))
251 #define TDMA_LPF(x, y, len) \
252 ((x != TDMA_DUMMY_MARKER) ? (((x) * ((len)-1) + (y)) / (len)) : (y))
253 #define TDMA_SAMPLE(x, y) do { \
254 x = TDMA_LPF((x), TDMA_IN(y), TDMA_LPF_LEN); \
256 #define TDMA_EP_RND(x,mul) \
257 ((((x)%(mul)) >= ((mul)/2)) ? ((x) + ((mul) - 1)) / (mul) : (x)/(mul))
258 #define TDMA_AVG(x) TDMA_EP_RND(x, TDMA_EP_MULTIPLIER)
259 #endif /* IEEE80211_SUPPORT_TDMA */
261 SYSCTL_DECL(_hw_ath);
263 /* XXX validate sysctl values */
264 static int ath_longcalinterval = 30; /* long cals every 30 secs */
265 SYSCTL_INT(_hw_ath, OID_AUTO, longcal, CTLFLAG_RW, &ath_longcalinterval,
266 0, "long chip calibration interval (secs)");
267 static int ath_shortcalinterval = 100; /* short cals every 100 ms */
268 SYSCTL_INT(_hw_ath, OID_AUTO, shortcal, CTLFLAG_RW, &ath_shortcalinterval,
269 0, "short chip calibration interval (msecs)");
270 static int ath_resetcalinterval = 20*60; /* reset cal state 20 mins */
271 SYSCTL_INT(_hw_ath, OID_AUTO, resetcal, CTLFLAG_RW, &ath_resetcalinterval,
272 0, "reset chip calibration results (secs)");
274 static int ath_rxbuf = ATH_RXBUF; /* # rx buffers to allocate */
275 SYSCTL_INT(_hw_ath, OID_AUTO, rxbuf, CTLFLAG_RW, &ath_rxbuf,
276 0, "rx buffers allocated");
277 TUNABLE_INT("hw.ath.rxbuf", &ath_rxbuf);
278 static int ath_txbuf = ATH_TXBUF; /* # tx buffers to allocate */
279 SYSCTL_INT(_hw_ath, OID_AUTO, txbuf, CTLFLAG_RW, &ath_txbuf,
280 0, "tx buffers allocated");
281 TUNABLE_INT("hw.ath.txbuf", &ath_txbuf);
283 static int ath_bstuck_threshold = 4; /* max missed beacons */
284 SYSCTL_INT(_hw_ath, OID_AUTO, bstuck, CTLFLAG_RW, &ath_bstuck_threshold,
285 0, "max missed beacon xmits before chip reset");
289 ATH_DEBUG_XMIT = 0x00000001, /* basic xmit operation */
290 ATH_DEBUG_XMIT_DESC = 0x00000002, /* xmit descriptors */
291 ATH_DEBUG_RECV = 0x00000004, /* basic recv operation */
292 ATH_DEBUG_RECV_DESC = 0x00000008, /* recv descriptors */
293 ATH_DEBUG_RATE = 0x00000010, /* rate control */
294 ATH_DEBUG_RESET = 0x00000020, /* reset processing */
295 ATH_DEBUG_MODE = 0x00000040, /* mode init/setup */
296 ATH_DEBUG_BEACON = 0x00000080, /* beacon handling */
297 ATH_DEBUG_WATCHDOG = 0x00000100, /* watchdog timeout */
298 ATH_DEBUG_INTR = 0x00001000, /* ISR */
299 ATH_DEBUG_TX_PROC = 0x00002000, /* tx ISR proc */
300 ATH_DEBUG_RX_PROC = 0x00004000, /* rx ISR proc */
301 ATH_DEBUG_BEACON_PROC = 0x00008000, /* beacon ISR proc */
302 ATH_DEBUG_CALIBRATE = 0x00010000, /* periodic calibration */
303 ATH_DEBUG_KEYCACHE = 0x00020000, /* key cache management */
304 ATH_DEBUG_STATE = 0x00040000, /* 802.11 state transitions */
305 ATH_DEBUG_NODE = 0x00080000, /* node management */
306 ATH_DEBUG_LED = 0x00100000, /* led management */
307 ATH_DEBUG_FF = 0x00200000, /* fast frames */
308 ATH_DEBUG_DFS = 0x00400000, /* DFS processing */
309 ATH_DEBUG_TDMA = 0x00800000, /* TDMA processing */
310 ATH_DEBUG_TDMA_TIMER = 0x01000000, /* TDMA timer processing */
311 ATH_DEBUG_REGDOMAIN = 0x02000000, /* regulatory processing */
312 ATH_DEBUG_FATAL = 0x80000000, /* fatal errors */
313 ATH_DEBUG_ANY = 0xffffffff
315 static int ath_debug = 0;
316 SYSCTL_INT(_hw_ath, OID_AUTO, debug, CTLFLAG_RW, &ath_debug,
317 0, "control debugging printfs");
318 TUNABLE_INT("hw.ath.debug", &ath_debug);
320 #define IFF_DUMPPKTS(sc, m) \
321 ((sc->sc_debug & (m)) || \
322 (sc->sc_ifp->if_flags & (IFF_DEBUG|IFF_LINK2)) == (IFF_DEBUG|IFF_LINK2))
323 #define DPRINTF(sc, m, fmt, ...) do { \
324 if (sc->sc_debug & (m)) \
325 kprintf(fmt, __VA_ARGS__); \
327 #define KEYPRINTF(sc, ix, hk, mac) do { \
328 if (sc->sc_debug & ATH_DEBUG_KEYCACHE) \
329 ath_keyprint(sc, __func__, ix, hk, mac); \
331 static void ath_printrxbuf(struct ath_softc *, const struct ath_buf *bf,
333 static void ath_printtxbuf(struct ath_softc *, const struct ath_buf *bf,
334 u_int qnum, u_int ix, int done);
336 #define IFF_DUMPPKTS(sc, m) \
337 ((sc->sc_ifp->if_flags & (IFF_DEBUG|IFF_LINK2)) == (IFF_DEBUG|IFF_LINK2))
338 #define DPRINTF(sc, m, fmt, ...) do { \
341 #define KEYPRINTF(sc, k, ix, mac) do { \
346 MALLOC_DEFINE(M_ATHDEV, "athdev", "ath driver dma buffers");
349 ath_attach(u_int16_t devid, struct ath_softc *sc)
352 struct ieee80211com *ic;
353 struct ath_hal *ah = NULL;
357 uint8_t macaddr[IEEE80211_ADDR_LEN];
359 DPRINTF(sc, ATH_DEBUG_ANY, "%s: devid 0x%x\n", __func__, devid);
361 ifp = sc->sc_ifp = if_alloc(IFT_IEEE80211);
363 device_printf(sc->sc_dev, "can not if_alloc()\n");
369 /* set these up early for if_printf use */
370 if_initname(ifp, device_get_name(sc->sc_dev),
371 device_get_unit(sc->sc_dev));
373 /* prepare sysctl tree for use in sub modules */
374 sysctl_ctx_init(&sc->sc_sysctl_ctx);
375 sc->sc_sysctl_tree = SYSCTL_ADD_NODE(&sc->sc_sysctl_ctx,
376 SYSCTL_STATIC_CHILDREN(_hw),
378 device_get_nameunit(sc->sc_dev),
381 ah = ath_hal_attach(devid, sc, sc->sc_st, sc->sc_sh, &status);
383 if_printf(ifp, "unable to attach hardware; HAL status %u\n",
389 sc->sc_invalid = 0; /* ready to go, enable interrupt handling */
391 sc->sc_debug = ath_debug;
395 * Check if the MAC has multi-rate retry support.
396 * We do this by trying to setup a fake extended
397 * descriptor. MAC's that don't have support will
398 * return false w/o doing anything. MAC's that do
399 * support it will return true w/o doing anything.
401 sc->sc_mrretry = ath_hal_setupxtxdesc(ah, NULL, 0,0, 0,0, 0,0);
404 * Check if the device has hardware counters for PHY
405 * errors. If so we need to enable the MIB interrupt
406 * so we can act on stat triggers.
408 if (ath_hal_hwphycounters(ah))
412 * Get the hardware key cache size.
414 sc->sc_keymax = ath_hal_keycachesize(ah);
415 if (sc->sc_keymax > ATH_KEYMAX) {
416 if_printf(ifp, "Warning, using only %u of %u key cache slots\n",
417 ATH_KEYMAX, sc->sc_keymax);
418 sc->sc_keymax = ATH_KEYMAX;
421 * Reset the key cache since some parts do not
422 * reset the contents on initial power up.
424 for (i = 0; i < sc->sc_keymax; i++)
425 ath_hal_keyreset(ah, i);
428 * Collect the default channel list.
430 error = ath_getchannels(sc);
435 * Setup rate tables for all potential media types.
437 ath_rate_setup(sc, IEEE80211_MODE_11A);
438 ath_rate_setup(sc, IEEE80211_MODE_11B);
439 ath_rate_setup(sc, IEEE80211_MODE_11G);
440 ath_rate_setup(sc, IEEE80211_MODE_TURBO_A);
441 ath_rate_setup(sc, IEEE80211_MODE_TURBO_G);
442 ath_rate_setup(sc, IEEE80211_MODE_STURBO_A);
443 ath_rate_setup(sc, IEEE80211_MODE_11NA);
444 ath_rate_setup(sc, IEEE80211_MODE_11NG);
445 ath_rate_setup(sc, IEEE80211_MODE_HALF);
446 ath_rate_setup(sc, IEEE80211_MODE_QUARTER);
448 /* NB: setup here so ath_rate_update is happy */
449 ath_setcurmode(sc, IEEE80211_MODE_11A);
452 * Allocate tx+rx descriptors and populate the lists.
454 wlan_assert_serialized();
455 wlan_serialize_exit();
456 error = ath_desc_alloc(sc);
457 wlan_serialize_enter();
459 if_printf(ifp, "failed to allocate descriptors: %d\n", error);
462 callout_init(&sc->sc_cal_ch);
463 callout_init(&sc->sc_wd_ch);
465 sc->sc_tq = taskqueue_create("ath_taskq", M_INTWAIT,
466 taskqueue_thread_enqueue, &sc->sc_tq);
467 taskqueue_start_threads(&sc->sc_tq, 1, TDPRI_KERN_DAEMON, -1,
468 "%s taskq", ifp->if_xname);
470 TASK_INIT(&sc->sc_rxtask, 0, ath_rx_task, sc);
471 TASK_INIT(&sc->sc_bmisstask, 0, ath_bmiss_task, sc);
472 TASK_INIT(&sc->sc_bstucktask,0, ath_bstuck_task, sc);
475 * Allocate hardware transmit queues: one queue for
476 * beacon frames and one data queue for each QoS
477 * priority. Note that the hal handles reseting
478 * these queues at the needed time.
482 sc->sc_bhalq = ath_beaconq_setup(ah);
483 if (sc->sc_bhalq == (u_int) -1) {
484 if_printf(ifp, "unable to setup a beacon xmit queue!\n");
488 sc->sc_cabq = ath_txq_setup(sc, HAL_TX_QUEUE_CAB, 0);
489 if (sc->sc_cabq == NULL) {
490 if_printf(ifp, "unable to setup CAB xmit queue!\n");
494 /* NB: insure BK queue is the lowest priority h/w queue */
495 if (!ath_tx_setup(sc, WME_AC_BK, HAL_WME_AC_BK)) {
496 if_printf(ifp, "unable to setup xmit queue for %s traffic!\n",
497 ieee80211_wme_acnames[WME_AC_BK]);
501 if (!ath_tx_setup(sc, WME_AC_BE, HAL_WME_AC_BE) ||
502 !ath_tx_setup(sc, WME_AC_VI, HAL_WME_AC_VI) ||
503 !ath_tx_setup(sc, WME_AC_VO, HAL_WME_AC_VO)) {
505 * Not enough hardware tx queues to properly do WME;
506 * just punt and assign them all to the same h/w queue.
507 * We could do a better job of this if, for example,
508 * we allocate queues when we switch from station to
511 if (sc->sc_ac2q[WME_AC_VI] != NULL)
512 ath_tx_cleanupq(sc, sc->sc_ac2q[WME_AC_VI]);
513 if (sc->sc_ac2q[WME_AC_BE] != NULL)
514 ath_tx_cleanupq(sc, sc->sc_ac2q[WME_AC_BE]);
515 sc->sc_ac2q[WME_AC_BE] = sc->sc_ac2q[WME_AC_BK];
516 sc->sc_ac2q[WME_AC_VI] = sc->sc_ac2q[WME_AC_BK];
517 sc->sc_ac2q[WME_AC_VO] = sc->sc_ac2q[WME_AC_BK];
521 * Special case certain configurations. Note the
522 * CAB queue is handled by these specially so don't
523 * include them when checking the txq setup mask.
525 switch (sc->sc_txqsetup &~ (1<<sc->sc_cabq->axq_qnum)) {
527 TASK_INIT(&sc->sc_txtask, 0, ath_tx_task_q0, sc);
530 TASK_INIT(&sc->sc_txtask, 0, ath_tx_task_q0123, sc);
533 TASK_INIT(&sc->sc_txtask, 0, ath_tx_task, sc);
538 * Setup rate control. Some rate control modules
539 * call back to change the anntena state so expose
540 * the necessary entry points.
541 * XXX maybe belongs in struct ath_ratectrl?
543 sc->sc_setdefantenna = ath_setdefantenna;
544 sc->sc_rc = ath_rate_attach(sc);
545 if (sc->sc_rc == NULL) {
552 sc->sc_ledon = 0; /* low true */
553 sc->sc_ledidle = (2700*hz)/1000; /* 2.7sec */
554 callout_init_mp(&sc->sc_ledtimer);
556 * Auto-enable soft led processing for IBM cards and for
557 * 5211 minipci cards. Users can also manually enable/disable
558 * support with a sysctl.
560 sc->sc_softled = (devid == AR5212_DEVID_IBM || devid == AR5211_DEVID);
561 if (sc->sc_softled) {
562 ath_hal_gpioCfgOutput(ah, sc->sc_ledpin,
563 HAL_GPIO_MUX_MAC_NETWORK_LED);
564 ath_hal_gpioset(ah, sc->sc_ledpin, !sc->sc_ledon);
568 ifp->if_flags = IFF_SIMPLEX | IFF_BROADCAST | IFF_MULTICAST;
569 ifp->if_start = ath_start;
570 ifp->if_ioctl = ath_ioctl;
571 ifp->if_init = ath_init;
572 ifq_set_maxlen(&ifp->if_snd, IFQ_MAXLEN);
573 ifq_set_ready(&ifp->if_snd);
576 /* XXX not right but it's not used anywhere important */
577 ic->ic_phytype = IEEE80211_T_OFDM;
578 ic->ic_opmode = IEEE80211_M_STA;
580 IEEE80211_C_STA /* station mode */
581 | IEEE80211_C_IBSS /* ibss, nee adhoc, mode */
582 | IEEE80211_C_HOSTAP /* hostap mode */
583 | IEEE80211_C_MONITOR /* monitor mode */
584 | IEEE80211_C_AHDEMO /* adhoc demo mode */
585 | IEEE80211_C_WDS /* 4-address traffic works */
586 | IEEE80211_C_MBSS /* mesh point link mode */
587 | IEEE80211_C_SHPREAMBLE /* short preamble supported */
588 | IEEE80211_C_SHSLOT /* short slot time supported */
589 | IEEE80211_C_WPA /* capable of WPA1+WPA2 */
590 | IEEE80211_C_BGSCAN /* capable of bg scanning */
591 | IEEE80211_C_TXFRAG /* handle tx frags */
594 * Query the hal to figure out h/w crypto support.
596 if (ath_hal_ciphersupported(ah, HAL_CIPHER_WEP))
597 ic->ic_cryptocaps |= IEEE80211_CRYPTO_WEP;
598 if (ath_hal_ciphersupported(ah, HAL_CIPHER_AES_OCB))
599 ic->ic_cryptocaps |= IEEE80211_CRYPTO_AES_OCB;
600 if (ath_hal_ciphersupported(ah, HAL_CIPHER_AES_CCM))
601 ic->ic_cryptocaps |= IEEE80211_CRYPTO_AES_CCM;
602 if (ath_hal_ciphersupported(ah, HAL_CIPHER_CKIP))
603 ic->ic_cryptocaps |= IEEE80211_CRYPTO_CKIP;
604 if (ath_hal_ciphersupported(ah, HAL_CIPHER_TKIP)) {
605 ic->ic_cryptocaps |= IEEE80211_CRYPTO_TKIP;
607 * Check if h/w does the MIC and/or whether the
608 * separate key cache entries are required to
609 * handle both tx+rx MIC keys.
611 if (ath_hal_ciphersupported(ah, HAL_CIPHER_MIC))
612 ic->ic_cryptocaps |= IEEE80211_CRYPTO_TKIPMIC;
614 * If the h/w supports storing tx+rx MIC keys
615 * in one cache slot automatically enable use.
617 if (ath_hal_hastkipsplit(ah) ||
618 !ath_hal_settkipsplit(ah, AH_FALSE))
621 * If the h/w can do TKIP MIC together with WME then
622 * we use it; otherwise we force the MIC to be done
623 * in software by the net80211 layer.
625 if (ath_hal_haswmetkipmic(ah))
626 sc->sc_wmetkipmic = 1;
628 sc->sc_hasclrkey = ath_hal_ciphersupported(ah, HAL_CIPHER_CLR);
630 * Check for multicast key search support.
632 if (ath_hal_hasmcastkeysearch(sc->sc_ah) &&
633 !ath_hal_getmcastkeysearch(sc->sc_ah)) {
634 ath_hal_setmcastkeysearch(sc->sc_ah, 1);
636 sc->sc_mcastkey = ath_hal_getmcastkeysearch(ah);
638 * Mark key cache slots associated with global keys
639 * as in use. If we knew TKIP was not to be used we
640 * could leave the +32, +64, and +32+64 slots free.
642 for (i = 0; i < IEEE80211_WEP_NKID; i++) {
643 setbit(sc->sc_keymap, i);
644 setbit(sc->sc_keymap, i+64);
645 if (sc->sc_splitmic) {
646 setbit(sc->sc_keymap, i+32);
647 setbit(sc->sc_keymap, i+32+64);
651 * TPC support can be done either with a global cap or
652 * per-packet support. The latter is not available on
653 * all parts. We're a bit pedantic here as all parts
654 * support a global cap.
656 if (ath_hal_hastpc(ah) || ath_hal_hastxpowlimit(ah))
657 ic->ic_caps |= IEEE80211_C_TXPMGT;
660 * Mark WME capability only if we have sufficient
661 * hardware queues to do proper priority scheduling.
663 if (sc->sc_ac2q[WME_AC_BE] != sc->sc_ac2q[WME_AC_BK])
664 ic->ic_caps |= IEEE80211_C_WME;
666 * Check for misc other capabilities.
668 if (ath_hal_hasbursting(ah))
669 ic->ic_caps |= IEEE80211_C_BURST;
670 sc->sc_hasbmask = ath_hal_hasbssidmask(ah);
671 sc->sc_hasbmatch = ath_hal_hasbssidmatch(ah);
672 sc->sc_hastsfadd = ath_hal_hastsfadjust(ah);
673 if (ath_hal_hasfastframes(ah))
674 ic->ic_caps |= IEEE80211_C_FF;
675 wmodes = ath_hal_getwirelessmodes(ah);
676 if (wmodes & (HAL_MODE_108G|HAL_MODE_TURBO))
677 ic->ic_caps |= IEEE80211_C_TURBOP;
678 #ifdef IEEE80211_SUPPORT_TDMA
679 if (ath_hal_macversion(ah) > 0x78) {
680 ic->ic_caps |= IEEE80211_C_TDMA; /* capable of TDMA */
681 ic->ic_tdma_update = ath_tdma_update;
685 * Indicate we need the 802.11 header padded to a
686 * 32-bit boundary for 4-address and QoS frames.
688 ic->ic_flags |= IEEE80211_F_DATAPAD;
691 * Query the hal about antenna support.
693 sc->sc_defant = ath_hal_getdefantenna(ah);
696 * Not all chips have the VEOL support we want to
697 * use with IBSS beacons; check here for it.
699 sc->sc_hasveol = ath_hal_hasveol(ah);
701 /* get mac address from hardware */
702 ath_hal_getmac(ah, macaddr);
704 ath_hal_getbssidmask(ah, sc->sc_hwbssidmask);
706 /* NB: used to size node table key mapping array */
707 ic->ic_max_keyix = sc->sc_keymax;
708 /* call MI attach routine. */
709 ieee80211_ifattach(ic, macaddr);
710 ic->ic_setregdomain = ath_setregdomain;
711 ic->ic_getradiocaps = ath_getradiocaps;
712 sc->sc_opmode = HAL_M_STA;
714 /* override default methods */
715 ic->ic_newassoc = ath_newassoc;
716 ic->ic_updateslot = ath_updateslot;
717 ic->ic_wme.wme_update = ath_wme_update;
718 ic->ic_vap_create = ath_vap_create;
719 ic->ic_vap_delete = ath_vap_delete;
720 ic->ic_raw_xmit = ath_raw_xmit;
721 ic->ic_update_mcast = ath_update_mcast;
722 ic->ic_update_promisc = ath_update_promisc;
723 ic->ic_node_alloc = ath_node_alloc;
724 sc->sc_node_free = ic->ic_node_free;
725 ic->ic_node_free = ath_node_free;
726 ic->ic_node_getsignal = ath_node_getsignal;
727 ic->ic_scan_start = ath_scan_start;
728 ic->ic_scan_end = ath_scan_end;
729 ic->ic_set_channel = ath_set_channel;
731 ieee80211_radiotap_attach(ic,
732 &sc->sc_tx_th.wt_ihdr, sizeof(sc->sc_tx_th),
733 ATH_TX_RADIOTAP_PRESENT,
734 &sc->sc_rx_th.wr_ihdr, sizeof(sc->sc_rx_th),
735 ATH_RX_RADIOTAP_PRESENT);
738 * Setup dynamic sysctl's now that country code and
739 * regdomain are available from the hal.
741 ath_sysctlattach(sc);
742 ath_sysctl_stats_attach(sc);
745 ieee80211_announce(ic);
761 ath_detach(struct ath_softc *sc)
763 struct ifnet *ifp = sc->sc_ifp;
765 DPRINTF(sc, ATH_DEBUG_ANY, "%s: if_flags %x\n",
766 __func__, ifp->if_flags);
769 * NB: the order of these is important:
770 * o stop the chip so no more interrupts will fire
771 * o call the 802.11 layer before detaching the hal to
772 * insure callbacks into the driver to delete global
773 * key cache entries can be handled
774 * o free the taskqueue which drains any pending tasks
775 * o reclaim the tx queue data structures after calling
776 * the 802.11 layer as we'll get called back to reclaim
777 * node state and potentially want to use them
778 * o to cleanup the tx queues the hal is called, so detach
780 * Other than that, it's straightforward...
783 ieee80211_ifdetach(ifp->if_l2com);
784 taskqueue_free(sc->sc_tq);
786 if (sc->sc_tx99 != NULL)
787 sc->sc_tx99->detach(sc->sc_tx99);
789 ath_rate_detach(sc->sc_rc);
792 ath_hal_detach(sc->sc_ah); /* NB: sets chip in full sleep */
793 if (sc->sc_sysctl_tree) {
794 sysctl_ctx_free(&sc->sc_sysctl_ctx);
795 sc->sc_sysctl_tree = NULL;
803 * MAC address handling for multiple BSS on the same radio.
804 * The first vap uses the MAC address from the EEPROM. For
805 * subsequent vap's we set the U/L bit (bit 1) in the MAC
806 * address and use the next six bits as an index.
809 assign_address(struct ath_softc *sc, uint8_t mac[IEEE80211_ADDR_LEN], int clone)
813 if (clone && sc->sc_hasbmask) {
814 /* NB: we only do this if h/w supports multiple bssid */
815 for (i = 0; i < 8; i++)
816 if ((sc->sc_bssidmask & (1<<i)) == 0)
819 mac[0] |= (i << 2)|0x2;
822 sc->sc_bssidmask |= 1<<i;
823 sc->sc_hwbssidmask[0] &= ~mac[0];
829 reclaim_address(struct ath_softc *sc, const uint8_t mac[IEEE80211_ADDR_LEN])
834 if (i != 0 || --sc->sc_nbssid0 == 0) {
835 sc->sc_bssidmask &= ~(1<<i);
836 /* recalculate bssid mask from remaining addresses */
838 for (i = 1; i < 8; i++)
839 if (sc->sc_bssidmask & (1<<i))
840 mask &= ~((i<<2)|0x2);
841 sc->sc_hwbssidmask[0] |= mask;
846 * Assign a beacon xmit slot. We try to space out
847 * assignments so when beacons are staggered the
848 * traffic coming out of the cab q has maximal time
849 * to go out before the next beacon is scheduled.
852 assign_bslot(struct ath_softc *sc)
857 for (slot = 0; slot < ATH_BCBUF; slot++)
858 if (sc->sc_bslot[slot] == NULL) {
859 if (sc->sc_bslot[(slot+1)%ATH_BCBUF] == NULL &&
860 sc->sc_bslot[(slot-1)%ATH_BCBUF] == NULL)
863 /* NB: keep looking for a double slot */
868 static struct ieee80211vap *
869 ath_vap_create(struct ieee80211com *ic,
870 const char name[IFNAMSIZ], int unit, int opmode, int flags,
871 const uint8_t bssid[IEEE80211_ADDR_LEN],
872 const uint8_t mac0[IEEE80211_ADDR_LEN])
874 struct ath_softc *sc = ic->ic_ifp->if_softc;
876 struct ieee80211vap *vap;
877 uint8_t mac[IEEE80211_ADDR_LEN];
878 int ic_opmode, needbeacon, error;
880 avp = (struct ath_vap *) kmalloc(sizeof(struct ath_vap),
881 M_80211_VAP, M_WAITOK | M_ZERO);
883 IEEE80211_ADDR_COPY(mac, mac0);
885 ic_opmode = opmode; /* default to opmode of new vap */
887 case IEEE80211_M_STA:
888 if (sc->sc_nstavaps != 0) { /* XXX only 1 for now */
889 device_printf(sc->sc_dev, "only 1 sta vap supported\n");
894 * With multiple vaps we must fall back
895 * to s/w beacon miss handling.
897 flags |= IEEE80211_CLONE_NOBEACONS;
899 if (flags & IEEE80211_CLONE_NOBEACONS) {
901 * Station mode w/o beacons are implemented w/ AP mode.
903 ic_opmode = IEEE80211_M_HOSTAP;
906 case IEEE80211_M_IBSS:
907 if (sc->sc_nvaps != 0) { /* XXX only 1 for now */
908 device_printf(sc->sc_dev,
909 "only 1 ibss vap supported\n");
914 case IEEE80211_M_AHDEMO:
915 #ifdef IEEE80211_SUPPORT_TDMA
916 if (flags & IEEE80211_CLONE_TDMA) {
917 if (sc->sc_nvaps != 0) {
918 device_printf(sc->sc_dev,
919 "only 1 tdma vap supported\n");
923 flags |= IEEE80211_CLONE_NOBEACONS;
927 case IEEE80211_M_MONITOR:
928 if (sc->sc_nvaps != 0 && ic->ic_opmode != opmode) {
930 * Adopt existing mode. Adding a monitor or ahdemo
931 * vap to an existing configuration is of dubious
932 * value but should be ok.
934 /* XXX not right for monitor mode */
935 ic_opmode = ic->ic_opmode;
938 case IEEE80211_M_HOSTAP:
939 case IEEE80211_M_MBSS:
942 case IEEE80211_M_WDS:
943 if (sc->sc_nvaps != 0 && ic->ic_opmode == IEEE80211_M_STA) {
944 device_printf(sc->sc_dev,
945 "wds not supported in sta mode\n");
949 * Silently remove any request for a unique
950 * bssid; WDS vap's always share the local
953 flags &= ~IEEE80211_CLONE_BSSID;
954 if (sc->sc_nvaps == 0)
955 ic_opmode = IEEE80211_M_HOSTAP;
957 ic_opmode = ic->ic_opmode;
960 device_printf(sc->sc_dev, "unknown opmode %d\n", opmode);
964 * Check that a beacon buffer is available; the code below assumes it.
966 if (needbeacon & STAILQ_EMPTY(&sc->sc_bbuf)) {
967 device_printf(sc->sc_dev, "no beacon buffer available\n");
972 if (opmode == IEEE80211_M_HOSTAP || opmode == IEEE80211_M_MBSS) {
973 assign_address(sc, mac, flags & IEEE80211_CLONE_BSSID);
974 ath_hal_setbssidmask(sc->sc_ah, sc->sc_hwbssidmask);
978 /* XXX can't hold mutex across if_alloc */
979 error = ieee80211_vap_setup(ic, vap, name, unit, opmode, flags,
982 device_printf(sc->sc_dev, "%s: error %d creating vap\n",
987 /* h/w crypto support */
988 vap->iv_key_alloc = ath_key_alloc;
989 vap->iv_key_delete = ath_key_delete;
990 vap->iv_key_set = ath_key_set;
991 vap->iv_key_update_begin = ath_key_update_begin;
992 vap->iv_key_update_end = ath_key_update_end;
994 /* override various methods */
995 avp->av_recv_mgmt = vap->iv_recv_mgmt;
996 vap->iv_recv_mgmt = ath_recv_mgmt;
997 vap->iv_reset = ath_reset_vap;
998 vap->iv_update_beacon = ath_beacon_update;
999 avp->av_newstate = vap->iv_newstate;
1000 vap->iv_newstate = ath_newstate;
1001 avp->av_bmiss = vap->iv_bmiss;
1002 vap->iv_bmiss = ath_bmiss_vap;
1007 * Allocate beacon state and setup the q for buffered
1008 * multicast frames. We know a beacon buffer is
1009 * available because we checked above.
1011 avp->av_bcbuf = STAILQ_FIRST(&sc->sc_bbuf);
1012 STAILQ_REMOVE_HEAD(&sc->sc_bbuf, bf_list);
1013 if (opmode != IEEE80211_M_IBSS || !sc->sc_hasveol) {
1015 * Assign the vap to a beacon xmit slot. As above
1016 * this cannot fail to find a free one.
1018 avp->av_bslot = assign_bslot(sc);
1019 KASSERT(sc->sc_bslot[avp->av_bslot] == NULL,
1020 ("beacon slot %u not empty", avp->av_bslot));
1021 sc->sc_bslot[avp->av_bslot] = vap;
1024 if (sc->sc_hastsfadd && sc->sc_nbcnvaps > 0) {
1026 * Multple vaps are to transmit beacons and we
1027 * have h/w support for TSF adjusting; enable
1028 * use of staggered beacons.
1030 sc->sc_stagbeacons = 1;
1032 ath_txq_init(sc, &avp->av_mcastq, ATH_TXQ_SWQ);
1035 ic->ic_opmode = ic_opmode;
1036 if (opmode != IEEE80211_M_WDS) {
1038 if (opmode == IEEE80211_M_STA)
1040 if (opmode == IEEE80211_M_MBSS)
1043 switch (ic_opmode) {
1044 case IEEE80211_M_IBSS:
1045 sc->sc_opmode = HAL_M_IBSS;
1047 case IEEE80211_M_STA:
1048 sc->sc_opmode = HAL_M_STA;
1050 case IEEE80211_M_AHDEMO:
1051 #ifdef IEEE80211_SUPPORT_TDMA
1052 if (vap->iv_caps & IEEE80211_C_TDMA) {
1054 /* NB: disable tsf adjust */
1055 sc->sc_stagbeacons = 0;
1058 * NB: adhoc demo mode is a pseudo mode; to the hal it's
1063 case IEEE80211_M_HOSTAP:
1064 case IEEE80211_M_MBSS:
1065 sc->sc_opmode = HAL_M_HOSTAP;
1067 case IEEE80211_M_MONITOR:
1068 sc->sc_opmode = HAL_M_MONITOR;
1071 /* XXX should not happen */
1074 if (sc->sc_hastsfadd) {
1076 * Configure whether or not TSF adjust should be done.
1078 ath_hal_settsfadjust(sc->sc_ah, sc->sc_stagbeacons);
1080 if (flags & IEEE80211_CLONE_NOBEACONS) {
1082 * Enable s/w beacon miss handling.
1087 /* complete setup */
1088 ieee80211_vap_attach(vap, ath_media_change, ieee80211_media_status);
1091 reclaim_address(sc, mac);
1092 ath_hal_setbssidmask(sc->sc_ah, sc->sc_hwbssidmask);
1094 kfree(avp, M_80211_VAP);
1099 ath_vap_delete(struct ieee80211vap *vap)
1101 struct ieee80211com *ic = vap->iv_ic;
1102 struct ifnet *ifp = ic->ic_ifp;
1103 struct ath_softc *sc = ifp->if_softc;
1104 struct ath_hal *ah = sc->sc_ah;
1105 struct ath_vap *avp = ATH_VAP(vap);
1107 if (ifp->if_flags & IFF_RUNNING) {
1109 * Quiesce the hardware while we remove the vap. In
1110 * particular we need to reclaim all references to
1111 * the vap state by any frames pending on the tx queues.
1113 ath_hal_intrset(ah, 0); /* disable interrupts */
1114 ath_draintxq(sc); /* stop xmit side */
1115 ath_stoprecv(sc); /* stop recv side */
1118 ieee80211_vap_detach(vap);
1120 * Reclaim beacon state. Note this must be done before
1121 * the vap instance is reclaimed as we may have a reference
1122 * to it in the buffer for the beacon frame.
1124 if (avp->av_bcbuf != NULL) {
1125 if (avp->av_bslot != -1) {
1126 sc->sc_bslot[avp->av_bslot] = NULL;
1129 ath_beacon_return(sc, avp->av_bcbuf);
1130 avp->av_bcbuf = NULL;
1131 if (sc->sc_nbcnvaps == 0) {
1132 sc->sc_stagbeacons = 0;
1133 if (sc->sc_hastsfadd)
1134 ath_hal_settsfadjust(sc->sc_ah, 0);
1137 * Reclaim any pending mcast frames for the vap.
1139 ath_tx_draintxq(sc, &avp->av_mcastq);
1142 * Update bookkeeping.
1144 if (vap->iv_opmode == IEEE80211_M_STA) {
1146 if (sc->sc_nstavaps == 0 && sc->sc_swbmiss)
1148 } else if (vap->iv_opmode == IEEE80211_M_HOSTAP ||
1149 vap->iv_opmode == IEEE80211_M_MBSS) {
1150 reclaim_address(sc, vap->iv_myaddr);
1151 ath_hal_setbssidmask(ah, sc->sc_hwbssidmask);
1152 if (vap->iv_opmode == IEEE80211_M_MBSS)
1155 if (vap->iv_opmode != IEEE80211_M_WDS)
1157 #ifdef IEEE80211_SUPPORT_TDMA
1158 /* TDMA operation ceases when the last vap is destroyed */
1159 if (sc->sc_tdma && sc->sc_nvaps == 0) {
1164 kfree(avp, M_80211_VAP);
1166 if (ifp->if_flags & IFF_RUNNING) {
1168 * Restart rx+tx machines if still running (RUNNING will
1169 * be reset if we just destroyed the last vap).
1171 if (ath_startrecv(sc) != 0)
1172 if_printf(ifp, "%s: unable to restart recv logic\n",
1174 if (sc->sc_beacons) { /* restart beacons */
1175 #ifdef IEEE80211_SUPPORT_TDMA
1177 ath_tdma_config(sc, NULL);
1180 ath_beacon_config(sc, NULL);
1182 ath_hal_intrset(ah, sc->sc_imask);
1187 ath_suspend(struct ath_softc *sc)
1189 struct ifnet *ifp = sc->sc_ifp;
1190 struct ieee80211com *ic = ifp->if_l2com;
1192 DPRINTF(sc, ATH_DEBUG_ANY, "%s: if_flags %x\n",
1193 __func__, ifp->if_flags);
1195 sc->sc_resume_up = (ifp->if_flags & IFF_UP) != 0;
1196 if (ic->ic_opmode == IEEE80211_M_STA)
1199 ieee80211_suspend_all(ic);
1201 * NB: don't worry about putting the chip in low power
1202 * mode; pci will power off our socket on suspend and
1203 * CardBus detaches the device.
1208 * Reset the key cache since some parts do not reset the
1209 * contents on resume. First we clear all entries, then
1210 * re-load keys that the 802.11 layer assumes are setup
1214 ath_reset_keycache(struct ath_softc *sc)
1216 struct ifnet *ifp = sc->sc_ifp;
1217 struct ieee80211com *ic = ifp->if_l2com;
1218 struct ath_hal *ah = sc->sc_ah;
1221 for (i = 0; i < sc->sc_keymax; i++)
1222 ath_hal_keyreset(ah, i);
1223 ieee80211_crypto_reload_keys(ic);
1227 ath_resume(struct ath_softc *sc)
1229 struct ifnet *ifp = sc->sc_ifp;
1230 struct ieee80211com *ic = ifp->if_l2com;
1231 struct ath_hal *ah = sc->sc_ah;
1234 DPRINTF(sc, ATH_DEBUG_ANY, "%s: if_flags %x\n",
1235 __func__, ifp->if_flags);
1238 * Must reset the chip before we reload the
1239 * keycache as we were powered down on suspend.
1241 ath_hal_reset(ah, sc->sc_opmode,
1242 sc->sc_curchan != NULL ? sc->sc_curchan : ic->ic_curchan,
1244 ath_reset_keycache(sc);
1245 if (sc->sc_resume_up) {
1246 if (ic->ic_opmode == IEEE80211_M_STA) {
1249 * Program the beacon registers using the last rx'd
1250 * beacon frame and enable sync on the next beacon
1251 * we see. This should handle the case where we
1252 * wakeup and find the same AP and also the case where
1253 * we wakeup and need to roam. For the latter we
1254 * should get bmiss events that trigger a roam.
1256 ath_beacon_config(sc, NULL);
1257 sc->sc_syncbeacon = 1;
1259 ieee80211_resume_all(ic);
1261 if (sc->sc_softled) {
1262 ath_hal_gpioCfgOutput(ah, sc->sc_ledpin,
1263 HAL_GPIO_MUX_MAC_NETWORK_LED);
1264 ath_hal_gpioset(ah, sc->sc_ledpin, !sc->sc_ledon);
1269 ath_shutdown(struct ath_softc *sc)
1271 struct ifnet *ifp = sc->sc_ifp;
1273 DPRINTF(sc, ATH_DEBUG_ANY, "%s: if_flags %x\n",
1274 __func__, ifp->if_flags);
1277 /* NB: no point powering down chip as we're about to reboot */
1281 * Interrupt handler. Most of the actual processing is deferred.
1286 struct ath_softc *sc = arg;
1287 struct ifnet *ifp = sc->sc_ifp;
1288 struct ath_hal *ah = sc->sc_ah;
1292 if (sc->sc_invalid) {
1294 * The hardware is not ready/present, don't touch anything.
1295 * Note this can happen early on if the IRQ is shared.
1297 DPRINTF(sc, ATH_DEBUG_ANY, "%s: invalid; ignored\n", __func__);
1301 if (!ath_hal_intrpend(ah)) /* shared irq, not for us */
1303 if ((ifp->if_flags & IFF_UP) == 0 ||
1304 (ifp->if_flags & IFF_RUNNING) == 0) {
1307 DPRINTF(sc, ATH_DEBUG_ANY, "%s: if_flags 0x%x\n",
1308 __func__, ifp->if_flags);
1309 ath_hal_getisr(ah, &status); /* clear ISR */
1310 ath_hal_intrset(ah, 0); /* disable further intr's */
1314 * Figure out the reason(s) for the interrupt. Note
1315 * that the hal returns a pseudo-ISR that may include
1316 * bits we haven't explicitly enabled so we mask the
1317 * value to insure we only process bits we requested.
1319 ath_hal_getisr(ah, &ostatus); /* NB: clears ISR too */
1320 DPRINTF(sc, ATH_DEBUG_INTR, "%s: status 0x%x\n", __func__, ostatus);
1321 status = ostatus & sc->sc_imask; /* discard unasked for bits */
1322 if (status & HAL_INT_FATAL) {
1323 sc->sc_stats.ast_hardware++;
1324 ath_hal_intrset(ah, 0); /* disable intr's until reset */
1325 ath_fatal_proc(sc, 0);
1327 if (status & HAL_INT_SWBA) {
1329 * Software beacon alert--time to send a beacon.
1330 * Handle beacon transmission directly; deferring
1331 * this is too slow to meet timing constraints
1334 #ifdef IEEE80211_SUPPORT_TDMA
1336 if (sc->sc_tdmaswba == 0) {
1337 struct ieee80211com *ic = ifp->if_l2com;
1338 struct ieee80211vap *vap =
1339 TAILQ_FIRST(&ic->ic_vaps);
1340 ath_tdma_beacon_send(sc, vap);
1342 vap->iv_tdma->tdma_bintval;
1348 ath_beacon_proc(sc, 0);
1349 #ifdef IEEE80211_SUPPORT_SUPERG
1351 * Schedule the rx taskq in case there's no
1352 * traffic so any frames held on the staging
1353 * queue are aged and potentially flushed.
1355 taskqueue_enqueue(sc->sc_tq, &sc->sc_rxtask);
1361 * NB: The hardware should re-read the link when the RXE
1362 * bit is written, but it doesn't work at least on
1365 if (status & HAL_INT_RXEOL) {
1366 sc->sc_stats.ast_rxeol++;
1367 sc->sc_rxlink = NULL;
1370 if (status & HAL_INT_TXURN) {
1371 sc->sc_stats.ast_txurn++;
1372 /* bump tx trigger level */
1373 ath_hal_updatetxtriglevel(ah, AH_TRUE);
1376 if (status & HAL_INT_RX)
1377 taskqueue_enqueue(sc->sc_tq, &sc->sc_rxtask);
1379 if (status & HAL_INT_TX)
1380 taskqueue_enqueue(sc->sc_tq, &sc->sc_txtask);
1382 if (status & HAL_INT_BMISS) {
1383 sc->sc_stats.ast_bmiss++;
1384 taskqueue_enqueue(sc->sc_tq, &sc->sc_bmisstask);
1387 if (status & HAL_INT_MIB) {
1388 sc->sc_stats.ast_mib++;
1390 * Disable interrupts until we service the MIB
1391 * interrupt; otherwise it will continue to fire.
1393 ath_hal_intrset(ah, 0);
1395 * Let the hal handle the event. We assume it will
1396 * clear whatever condition caused the interrupt.
1398 ath_hal_mibevent(ah, &sc->sc_halstats);
1399 ath_hal_intrset(ah, sc->sc_imask);
1402 if (status & HAL_INT_RXORN) {
1403 /* NB: hal marks HAL_INT_FATAL when RXORN is fatal */
1404 sc->sc_stats.ast_rxorn++;
1410 ath_fatal_proc(void *arg, int pending)
1412 struct ath_softc *sc = arg;
1413 struct ifnet *ifp = sc->sc_ifp;
1418 if_printf(ifp, "hardware error; resetting\n");
1420 * Fatal errors are unrecoverable. Typically these
1421 * are caused by DMA errors. Collect h/w state from
1422 * the hal so we can diagnose what's going on.
1424 if (ath_hal_getfatalstate(sc->sc_ah, &sp, &len)) {
1425 KASSERT(len >= 6*sizeof(u_int32_t), ("len %u bytes", len));
1427 if_printf(ifp, "0x%08x 0x%08x 0x%08x, 0x%08x 0x%08x 0x%08x\n",
1428 state[0], state[1] , state[2], state[3],
1429 state[4], state[5]);
1435 ath_bmiss_vap(struct ieee80211vap *vap)
1438 * Workaround phantom bmiss interrupts by sanity-checking
1439 * the time of our last rx'd frame. If it is within the
1440 * beacon miss interval then ignore the interrupt. If it's
1441 * truly a bmiss we'll get another interrupt soon and that'll
1442 * be dispatched up for processing. Note this applies only
1443 * for h/w beacon miss events.
1445 if ((vap->iv_flags_ext & IEEE80211_FEXT_SWBMISS) == 0) {
1446 struct ifnet *ifp = vap->iv_ic->ic_ifp;
1447 struct ath_softc *sc = ifp->if_softc;
1448 u_int64_t lastrx = sc->sc_lastrx;
1449 u_int64_t tsf = ath_hal_gettsf64(sc->sc_ah);
1450 u_int bmisstimeout =
1451 vap->iv_bmissthreshold * vap->iv_bss->ni_intval * 1024;
1453 DPRINTF(sc, ATH_DEBUG_BEACON,
1454 "%s: tsf %llu lastrx %lld (%llu) bmiss %u\n",
1455 __func__, (unsigned long long) tsf,
1456 (unsigned long long)(tsf - lastrx),
1457 (unsigned long long) lastrx, bmisstimeout);
1459 if (tsf - lastrx <= bmisstimeout) {
1460 sc->sc_stats.ast_bmiss_phantom++;
1464 ATH_VAP(vap)->av_bmiss(vap);
1468 ath_hal_gethangstate(struct ath_hal *ah, uint32_t mask, uint32_t *hangs)
1473 if (!ath_hal_getdiagstate(ah, 32, &mask, sizeof(mask), &sp, &rsize))
1475 KASSERT(rsize == sizeof(uint32_t), ("resultsize %u", rsize));
1476 *hangs = *(uint32_t *)sp;
1481 ath_bmiss_task(void *arg, int pending)
1483 struct ath_softc *sc = arg;
1484 struct ifnet *ifp = sc->sc_ifp;
1487 wlan_serialize_enter();
1488 DPRINTF(sc, ATH_DEBUG_ANY, "%s: pending %u\n", __func__, pending);
1490 if (ath_hal_gethangstate(sc->sc_ah, 0xff, &hangs) && hangs != 0) {
1491 if_printf(ifp, "bb hang detected (0x%x), reseting\n", hangs);
1494 ieee80211_beacon_miss(ifp->if_l2com);
1496 wlan_serialize_exit();
1500 * Handle TKIP MIC setup to deal hardware that doesn't do MIC
1501 * calcs together with WME. If necessary disable the crypto
1502 * hardware and mark the 802.11 state so keys will be setup
1503 * with the MIC work done in software.
1506 ath_settkipmic(struct ath_softc *sc)
1508 struct ifnet *ifp = sc->sc_ifp;
1509 struct ieee80211com *ic = ifp->if_l2com;
1511 if ((ic->ic_cryptocaps & IEEE80211_CRYPTO_TKIP) && !sc->sc_wmetkipmic) {
1512 if (ic->ic_flags & IEEE80211_F_WME) {
1513 ath_hal_settkipmic(sc->sc_ah, AH_FALSE);
1514 ic->ic_cryptocaps &= ~IEEE80211_CRYPTO_TKIPMIC;
1516 ath_hal_settkipmic(sc->sc_ah, AH_TRUE);
1517 ic->ic_cryptocaps |= IEEE80211_CRYPTO_TKIPMIC;
1525 struct ath_softc *sc = (struct ath_softc *) arg;
1526 struct ifnet *ifp = sc->sc_ifp;
1527 struct ieee80211com *ic = ifp->if_l2com;
1528 struct ath_hal *ah = sc->sc_ah;
1531 DPRINTF(sc, ATH_DEBUG_ANY, "%s: if_flags 0x%x\n",
1532 __func__, ifp->if_flags);
1535 * Stop anything previously setup. This is safe
1536 * whether this is the first time through or not.
1538 ath_stop_locked(ifp);
1541 * The basic interface to setting the hardware in a good
1542 * state is ``reset''. On return the hardware is known to
1543 * be powered up and with interrupts disabled. This must
1544 * be followed by initialization of the appropriate bits
1545 * and then setup of the interrupt mask.
1548 if (!ath_hal_reset(ah, sc->sc_opmode, ic->ic_curchan, AH_FALSE, &status)) {
1549 if_printf(ifp, "unable to reset hardware; hal status %u\n",
1553 ath_chan_change(sc, ic->ic_curchan);
1556 * Likewise this is set during reset so update
1557 * state cached in the driver.
1559 sc->sc_diversity = ath_hal_getdiversity(ah);
1560 sc->sc_lastlongcal = 0;
1561 sc->sc_resetcal = 1;
1562 sc->sc_lastcalreset = 0;
1565 * Setup the hardware after reset: the key cache
1566 * is filled as needed and the receive engine is
1567 * set going. Frame transmit is handled entirely
1568 * in the frame output path; there's nothing to do
1569 * here except setup the interrupt mask.
1571 if (ath_startrecv(sc) != 0) {
1572 if_printf(ifp, "unable to start recv logic\n");
1577 * Enable interrupts.
1579 sc->sc_imask = HAL_INT_RX | HAL_INT_TX
1580 | HAL_INT_RXEOL | HAL_INT_RXORN
1581 | HAL_INT_FATAL | HAL_INT_GLOBAL;
1583 * Enable MIB interrupts when there are hardware phy counters.
1584 * Note we only do this (at the moment) for station mode.
1586 if (sc->sc_needmib && ic->ic_opmode == IEEE80211_M_STA)
1587 sc->sc_imask |= HAL_INT_MIB;
1589 ifp->if_flags |= IFF_RUNNING;
1590 callout_reset(&sc->sc_wd_ch, hz, ath_watchdog_callout, sc);
1591 ath_hal_intrset(ah, sc->sc_imask);
1594 #ifdef ATH_TX99_DIAG
1595 if (sc->sc_tx99 != NULL)
1596 sc->sc_tx99->start(sc->sc_tx99);
1599 ieee80211_start_all(ic); /* start all vap's */
1603 ath_stop_locked(struct ifnet *ifp)
1605 struct ath_softc *sc = ifp->if_softc;
1606 struct ath_hal *ah = sc->sc_ah;
1608 DPRINTF(sc, ATH_DEBUG_ANY, "%s: invalid %u if_flags 0x%x\n",
1609 __func__, sc->sc_invalid, ifp->if_flags);
1611 if (ifp->if_flags & IFF_RUNNING) {
1613 * Shutdown the hardware and driver:
1614 * reset 802.11 state machine
1616 * disable interrupts
1617 * turn off the radio
1618 * clear transmit machinery
1619 * clear receive machinery
1620 * drain and release tx queues
1621 * reclaim beacon resources
1622 * power down hardware
1624 * Note that some of this work is not possible if the
1625 * hardware is gone (invalid).
1627 #ifdef ATH_TX99_DIAG
1628 if (sc->sc_tx99 != NULL)
1629 sc->sc_tx99->stop(sc->sc_tx99);
1631 callout_stop(&sc->sc_wd_ch);
1632 sc->sc_wd_timer = 0;
1633 ifp->if_flags &= ~IFF_RUNNING;
1634 if (!sc->sc_invalid) {
1635 if (sc->sc_softled) {
1636 callout_stop(&sc->sc_ledtimer);
1637 ath_hal_gpioset(ah, sc->sc_ledpin,
1639 sc->sc_blinking = 0;
1641 ath_hal_intrset(ah, 0);
1644 if (!sc->sc_invalid) {
1646 ath_hal_phydisable(ah);
1648 sc->sc_rxlink = NULL;
1649 ath_beacon_free(sc); /* XXX not needed */
1654 ath_stop(struct ifnet *ifp)
1656 struct ath_softc *sc __unused = ifp->if_softc;
1658 ath_stop_locked(ifp);
1662 * Reset the hardware w/o losing operational state. This is
1663 * basically a more efficient way of doing ath_stop, ath_init,
1664 * followed by state transitions to the current 802.11
1665 * operational state. Used to recover from various errors and
1666 * to reset or reload hardware state.
1669 ath_reset(struct ifnet *ifp)
1671 struct ath_softc *sc = ifp->if_softc;
1672 struct ieee80211com *ic = ifp->if_l2com;
1673 struct ath_hal *ah = sc->sc_ah;
1676 kprintf("ath_reset\n");
1677 ath_hal_intrset(ah, 0); /* disable interrupts */
1678 ath_draintxq(sc); /* stop xmit side */
1679 ath_stoprecv(sc); /* stop recv side */
1680 ath_settkipmic(sc); /* configure TKIP MIC handling */
1681 /* NB: indicate channel change so we do a full reset */
1682 if (!ath_hal_reset(ah, sc->sc_opmode, ic->ic_curchan, AH_TRUE, &status))
1683 if_printf(ifp, "%s: unable to reset hardware; hal status %u\n",
1685 sc->sc_diversity = ath_hal_getdiversity(ah);
1686 if (ath_startrecv(sc) != 0) /* restart recv */
1687 if_printf(ifp, "%s: unable to start recv logic\n", __func__);
1689 * We may be doing a reset in response to an ioctl
1690 * that changes the channel so update any state that
1691 * might change as a result.
1693 ath_chan_change(sc, ic->ic_curchan);
1694 if (sc->sc_beacons) { /* restart beacons */
1695 #ifdef IEEE80211_SUPPORT_TDMA
1697 ath_tdma_config(sc, NULL);
1700 ath_beacon_config(sc, NULL);
1702 ath_hal_intrset(ah, sc->sc_imask);
1704 ath_start(ifp); /* restart xmit */
1709 ath_reset_vap(struct ieee80211vap *vap, u_long cmd)
1711 struct ieee80211com *ic = vap->iv_ic;
1712 struct ifnet *ifp = ic->ic_ifp;
1713 struct ath_softc *sc = ifp->if_softc;
1714 struct ath_hal *ah = sc->sc_ah;
1717 case IEEE80211_IOC_TXPOWER:
1719 * If per-packet TPC is enabled, then we have nothing
1720 * to do; otherwise we need to force the global limit.
1721 * All this can happen directly; no need to reset.
1723 if (!ath_hal_gettpc(ah))
1724 ath_hal_settxpowlimit(ah, ic->ic_txpowlimit);
1727 return ath_reset(ifp);
1730 static struct ath_buf *
1731 _ath_getbuf_locked(struct ath_softc *sc)
1735 bf = STAILQ_FIRST(&sc->sc_txbuf);
1736 if (bf != NULL && (bf->bf_flags & ATH_BUF_BUSY) == 0)
1737 STAILQ_REMOVE_HEAD(&sc->sc_txbuf, bf_list);
1741 kprintf("ath: ran out of descriptors\n");
1742 DPRINTF(sc, ATH_DEBUG_XMIT, "%s: %s\n", __func__,
1743 STAILQ_FIRST(&sc->sc_txbuf) == NULL ?
1744 "out of xmit buffers" : "xmit buffer busy");
1749 static struct ath_buf *
1750 ath_getbuf(struct ath_softc *sc)
1754 bf = _ath_getbuf_locked(sc);
1756 struct ifnet *ifp = sc->sc_ifp;
1758 DPRINTF(sc, ATH_DEBUG_XMIT, "%s: stop queue\n", __func__);
1759 sc->sc_stats.ast_tx_qstop++;
1760 ifp->if_flags |= IFF_OACTIVE;
1766 * Cleanup driver resources when we run out of buffers
1767 * while processing fragments; return the tx buffers
1768 * allocated and drop node references.
1771 ath_txfrag_cleanup(struct ath_softc *sc,
1772 ath_bufhead *frags, struct ieee80211_node *ni)
1774 struct ath_buf *bf, *next;
1776 STAILQ_FOREACH_MUTABLE(bf, frags, bf_list, next) {
1777 /* NB: bf assumed clean */
1778 STAILQ_REMOVE_HEAD(frags, bf_list);
1779 STAILQ_INSERT_HEAD(&sc->sc_txbuf, bf, bf_list);
1780 ieee80211_node_decref(ni);
1785 * Setup xmit of a fragmented frame. Allocate a buffer
1786 * for each frag and bump the node reference count to
1787 * reflect the held reference to be setup by ath_tx_start.
1790 ath_txfrag_setup(struct ath_softc *sc, ath_bufhead *frags,
1791 struct mbuf *m0, struct ieee80211_node *ni)
1796 for (m = m0->m_nextpkt; m != NULL; m = m->m_nextpkt) {
1797 bf = _ath_getbuf_locked(sc);
1798 if (bf == NULL) { /* out of buffers, cleanup */
1799 ath_txfrag_cleanup(sc, frags, ni);
1802 ieee80211_node_incref(ni);
1803 STAILQ_INSERT_TAIL(frags, bf, bf_list);
1806 return !STAILQ_EMPTY(frags);
1810 ath_start(struct ifnet *ifp)
1812 struct ath_softc *sc = ifp->if_softc;
1813 struct ieee80211_node *ni;
1815 struct mbuf *m, *next;
1818 if ((ifp->if_flags & IFF_RUNNING) == 0 || sc->sc_invalid) {
1819 ifq_purge(&ifp->if_snd);
1824 * Grab a TX buffer and associated resources.
1826 bf = ath_getbuf(sc);
1830 IF_DEQUEUE(&ifp->if_snd, m);
1832 STAILQ_INSERT_HEAD(&sc->sc_txbuf, bf, bf_list);
1835 ni = (struct ieee80211_node *) m->m_pkthdr.rcvif;
1837 * Check for fragmentation. If this frame
1838 * has been broken up verify we have enough
1839 * buffers to send all the fragments so all
1842 STAILQ_INIT(&frags);
1843 if ((m->m_flags & M_FRAG) &&
1844 !ath_txfrag_setup(sc, &frags, m, ni)) {
1845 DPRINTF(sc, ATH_DEBUG_XMIT,
1846 "%s: out of txfrag buffers\n", __func__);
1847 sc->sc_stats.ast_tx_nofrag++;
1855 * Pass the frame to the h/w for transmission.
1856 * Fragmented frames have each frag chained together
1857 * with m_nextpkt. We know there are sufficient ath_buf's
1858 * to send all the frags because of work done by
1859 * ath_txfrag_setup. We leave m_nextpkt set while
1860 * calling ath_tx_start so it can use it to extend the
1861 * the tx duration to cover the subsequent frag and
1862 * so it can reclaim all the mbufs in case of an error;
1863 * ath_tx_start clears m_nextpkt once it commits to
1864 * handing the frame to the hardware.
1866 next = m->m_nextpkt;
1867 if (ath_tx_start(sc, ni, bf, m)) {
1873 STAILQ_INSERT_HEAD(&sc->sc_txbuf, bf, bf_list);
1874 ath_txfrag_cleanup(sc, &frags, ni);
1876 ieee80211_free_node(ni);
1881 * Beware of state changing between frags.
1882 * XXX check sta power-save state?
1884 if (ni->ni_vap->iv_state != IEEE80211_S_RUN) {
1885 DPRINTF(sc, ATH_DEBUG_XMIT,
1886 "%s: flush fragmented packet, state %s\n",
1888 ieee80211_state_name[ni->ni_vap->iv_state]);
1893 bf = STAILQ_FIRST(&frags);
1894 KASSERT(bf != NULL, ("no buf for txfrag"));
1895 STAILQ_REMOVE_HEAD(&frags, bf_list);
1899 sc->sc_wd_timer = 5;
1904 ath_media_change(struct ifnet *ifp)
1906 int error = ieee80211_media_change(ifp);
1907 /* NB: only the fixed rate can change and that doesn't need a reset */
1908 return (error == ENETRESET ? 0 : error);
1913 ath_keyprint(struct ath_softc *sc, const char *tag, u_int ix,
1914 const HAL_KEYVAL *hk, const u_int8_t mac[IEEE80211_ADDR_LEN])
1916 static const char *ciphers[] = {
1926 kprintf("%s: [%02u] %-7s ", tag, ix, ciphers[hk->kv_type]);
1927 for (i = 0, n = hk->kv_len; i < n; i++)
1928 kprintf("%02x", hk->kv_val[i]);
1929 kprintf(" mac %6D", mac, ":");
1930 if (hk->kv_type == HAL_CIPHER_TKIP) {
1931 kprintf(" %s ", sc->sc_splitmic ? "mic" : "rxmic");
1932 for (i = 0; i < sizeof(hk->kv_mic); i++)
1933 kprintf("%02x", hk->kv_mic[i]);
1934 if (!sc->sc_splitmic) {
1936 for (i = 0; i < sizeof(hk->kv_txmic); i++)
1937 kprintf("%02x", hk->kv_txmic[i]);
1945 * Set a TKIP key into the hardware. This handles the
1946 * potential distribution of key state to multiple key
1947 * cache slots for TKIP.
1950 ath_keyset_tkip(struct ath_softc *sc, const struct ieee80211_key *k,
1951 HAL_KEYVAL *hk, const u_int8_t mac[IEEE80211_ADDR_LEN])
1953 #define IEEE80211_KEY_XR (IEEE80211_KEY_XMIT | IEEE80211_KEY_RECV)
1954 static const u_int8_t zerobssid[IEEE80211_ADDR_LEN];
1955 struct ath_hal *ah = sc->sc_ah;
1957 KASSERT(k->wk_cipher->ic_cipher == IEEE80211_CIPHER_TKIP,
1958 ("got a non-TKIP key, cipher %u", k->wk_cipher->ic_cipher));
1959 if ((k->wk_flags & IEEE80211_KEY_XR) == IEEE80211_KEY_XR) {
1960 if (sc->sc_splitmic) {
1962 * TX key goes at first index, RX key at the rx index.
1963 * The hal handles the MIC keys at index+64.
1965 memcpy(hk->kv_mic, k->wk_txmic, sizeof(hk->kv_mic));
1966 KEYPRINTF(sc, k->wk_keyix, hk, zerobssid);
1967 if (!ath_hal_keyset(ah, k->wk_keyix, hk, zerobssid))
1970 memcpy(hk->kv_mic, k->wk_rxmic, sizeof(hk->kv_mic));
1971 KEYPRINTF(sc, k->wk_keyix+32, hk, mac);
1972 /* XXX delete tx key on failure? */
1973 return ath_hal_keyset(ah, k->wk_keyix+32, hk, mac);
1976 * Room for both TX+RX MIC keys in one key cache
1977 * slot, just set key at the first index; the hal
1978 * will handle the rest.
1980 memcpy(hk->kv_mic, k->wk_rxmic, sizeof(hk->kv_mic));
1981 memcpy(hk->kv_txmic, k->wk_txmic, sizeof(hk->kv_txmic));
1982 KEYPRINTF(sc, k->wk_keyix, hk, mac);
1983 return ath_hal_keyset(ah, k->wk_keyix, hk, mac);
1985 } else if (k->wk_flags & IEEE80211_KEY_XMIT) {
1986 if (sc->sc_splitmic) {
1988 * NB: must pass MIC key in expected location when
1989 * the keycache only holds one MIC key per entry.
1991 memcpy(hk->kv_mic, k->wk_txmic, sizeof(hk->kv_txmic));
1993 memcpy(hk->kv_txmic, k->wk_txmic, sizeof(hk->kv_txmic));
1994 KEYPRINTF(sc, k->wk_keyix, hk, mac);
1995 return ath_hal_keyset(ah, k->wk_keyix, hk, mac);
1996 } else if (k->wk_flags & IEEE80211_KEY_RECV) {
1997 memcpy(hk->kv_mic, k->wk_rxmic, sizeof(hk->kv_mic));
1998 KEYPRINTF(sc, k->wk_keyix, hk, mac);
1999 return ath_hal_keyset(ah, k->wk_keyix, hk, mac);
2002 #undef IEEE80211_KEY_XR
2006 * Set a net80211 key into the hardware. This handles the
2007 * potential distribution of key state to multiple key
2008 * cache slots for TKIP with hardware MIC support.
2011 ath_keyset(struct ath_softc *sc, const struct ieee80211_key *k,
2012 struct ieee80211_node *bss)
2014 static const u_int8_t ciphermap[] = {
2015 HAL_CIPHER_WEP, /* IEEE80211_CIPHER_WEP */
2016 HAL_CIPHER_TKIP, /* IEEE80211_CIPHER_TKIP */
2017 HAL_CIPHER_AES_OCB, /* IEEE80211_CIPHER_AES_OCB */
2018 HAL_CIPHER_AES_CCM, /* IEEE80211_CIPHER_AES_CCM */
2019 (u_int8_t) -1, /* 4 is not allocated */
2020 HAL_CIPHER_CKIP, /* IEEE80211_CIPHER_CKIP */
2021 HAL_CIPHER_CLR, /* IEEE80211_CIPHER_NONE */
2023 struct ath_hal *ah = sc->sc_ah;
2024 const struct ieee80211_cipher *cip = k->wk_cipher;
2025 u_int8_t gmac[IEEE80211_ADDR_LEN];
2026 const u_int8_t *mac;
2029 memset(&hk, 0, sizeof(hk));
2031 * Software crypto uses a "clear key" so non-crypto
2032 * state kept in the key cache are maintained and
2033 * so that rx frames have an entry to match.
2035 if ((k->wk_flags & IEEE80211_KEY_SWCRYPT) == 0) {
2036 KASSERT(cip->ic_cipher < NELEM(ciphermap),
2037 ("invalid cipher type %u", cip->ic_cipher));
2038 hk.kv_type = ciphermap[cip->ic_cipher];
2039 hk.kv_len = k->wk_keylen;
2040 memcpy(hk.kv_val, k->wk_key, k->wk_keylen);
2042 hk.kv_type = HAL_CIPHER_CLR;
2044 if ((k->wk_flags & IEEE80211_KEY_GROUP) && sc->sc_mcastkey) {
2046 * Group keys on hardware that supports multicast frame
2047 * key search use a MAC that is the sender's address with
2048 * the high bit set instead of the app-specified address.
2050 IEEE80211_ADDR_COPY(gmac, bss->ni_macaddr);
2054 mac = k->wk_macaddr;
2056 if (hk.kv_type == HAL_CIPHER_TKIP &&
2057 (k->wk_flags & IEEE80211_KEY_SWMIC) == 0) {
2058 return ath_keyset_tkip(sc, k, &hk, mac);
2060 KEYPRINTF(sc, k->wk_keyix, &hk, mac);
2061 return ath_hal_keyset(ah, k->wk_keyix, &hk, mac);
2066 * Allocate tx/rx key slots for TKIP. We allocate two slots for
2067 * each key, one for decrypt/encrypt and the other for the MIC.
2070 key_alloc_2pair(struct ath_softc *sc,
2071 ieee80211_keyix *txkeyix, ieee80211_keyix *rxkeyix)
2075 KASSERT(sc->sc_splitmic, ("key cache !split"));
2076 /* XXX could optimize */
2077 for (i = 0; i < NELEM(sc->sc_keymap)/4; i++) {
2078 u_int8_t b = sc->sc_keymap[i];
2081 * One or more slots in this byte are free.
2089 /* XXX IEEE80211_KEY_XMIT | IEEE80211_KEY_RECV */
2090 if (isset(sc->sc_keymap, keyix+32) ||
2091 isset(sc->sc_keymap, keyix+64) ||
2092 isset(sc->sc_keymap, keyix+32+64)) {
2093 /* full pair unavailable */
2095 if (keyix == (i+1)*NBBY) {
2096 /* no slots were appropriate, advance */
2101 setbit(sc->sc_keymap, keyix);
2102 setbit(sc->sc_keymap, keyix+64);
2103 setbit(sc->sc_keymap, keyix+32);
2104 setbit(sc->sc_keymap, keyix+32+64);
2105 DPRINTF(sc, ATH_DEBUG_KEYCACHE,
2106 "%s: key pair %u,%u %u,%u\n",
2107 __func__, keyix, keyix+64,
2108 keyix+32, keyix+32+64);
2110 *rxkeyix = keyix+32;
2114 DPRINTF(sc, ATH_DEBUG_KEYCACHE, "%s: out of pair space\n", __func__);
2119 * Allocate tx/rx key slots for TKIP. We allocate two slots for
2120 * each key, one for decrypt/encrypt and the other for the MIC.
2123 key_alloc_pair(struct ath_softc *sc,
2124 ieee80211_keyix *txkeyix, ieee80211_keyix *rxkeyix)
2128 KASSERT(!sc->sc_splitmic, ("key cache split"));
2129 /* XXX could optimize */
2130 for (i = 0; i < NELEM(sc->sc_keymap)/4; i++) {
2131 u_int8_t b = sc->sc_keymap[i];
2134 * One or more slots in this byte are free.
2142 if (isset(sc->sc_keymap, keyix+64)) {
2143 /* full pair unavailable */
2145 if (keyix == (i+1)*NBBY) {
2146 /* no slots were appropriate, advance */
2151 setbit(sc->sc_keymap, keyix);
2152 setbit(sc->sc_keymap, keyix+64);
2153 DPRINTF(sc, ATH_DEBUG_KEYCACHE,
2154 "%s: key pair %u,%u\n",
2155 __func__, keyix, keyix+64);
2156 *txkeyix = *rxkeyix = keyix;
2160 DPRINTF(sc, ATH_DEBUG_KEYCACHE, "%s: out of pair space\n", __func__);
2165 * Allocate a single key cache slot.
2168 key_alloc_single(struct ath_softc *sc,
2169 ieee80211_keyix *txkeyix, ieee80211_keyix *rxkeyix)
2173 /* XXX try i,i+32,i+64,i+32+64 to minimize key pair conflicts */
2174 for (i = 0; i < NELEM(sc->sc_keymap); i++) {
2175 u_int8_t b = sc->sc_keymap[i];
2178 * One or more slots are free.
2183 setbit(sc->sc_keymap, keyix);
2184 DPRINTF(sc, ATH_DEBUG_KEYCACHE, "%s: key %u\n",
2186 *txkeyix = *rxkeyix = keyix;
2190 DPRINTF(sc, ATH_DEBUG_KEYCACHE, "%s: out of space\n", __func__);
2195 * Allocate one or more key cache slots for a uniacst key. The
2196 * key itself is needed only to identify the cipher. For hardware
2197 * TKIP with split cipher+MIC keys we allocate two key cache slot
2198 * pairs so that we can setup separate TX and RX MIC keys. Note
2199 * that the MIC key for a TKIP key at slot i is assumed by the
2200 * hardware to be at slot i+64. This limits TKIP keys to the first
2204 ath_key_alloc(struct ieee80211vap *vap, struct ieee80211_key *k,
2205 ieee80211_keyix *keyix, ieee80211_keyix *rxkeyix)
2207 struct ath_softc *sc = vap->iv_ic->ic_ifp->if_softc;
2210 * Group key allocation must be handled specially for
2211 * parts that do not support multicast key cache search
2212 * functionality. For those parts the key id must match
2213 * the h/w key index so lookups find the right key. On
2214 * parts w/ the key search facility we install the sender's
2215 * mac address (with the high bit set) and let the hardware
2216 * find the key w/o using the key id. This is preferred as
2217 * it permits us to support multiple users for adhoc and/or
2218 * multi-station operation.
2220 if (k->wk_keyix != IEEE80211_KEYIX_NONE) {
2222 * Only global keys should have key index assigned.
2224 if (!(&vap->iv_nw_keys[0] <= k &&
2225 k < &vap->iv_nw_keys[IEEE80211_WEP_NKID])) {
2226 /* should not happen */
2227 DPRINTF(sc, ATH_DEBUG_KEYCACHE,
2228 "%s: bogus group key\n", __func__);
2231 if (vap->iv_opmode != IEEE80211_M_HOSTAP ||
2232 !(k->wk_flags & IEEE80211_KEY_GROUP) ||
2235 * XXX we pre-allocate the global keys so
2236 * have no way to check if they've already
2239 *keyix = *rxkeyix = k - vap->iv_nw_keys;
2243 * Group key and device supports multicast key search.
2245 k->wk_keyix = IEEE80211_KEYIX_NONE;
2249 * We allocate two pair for TKIP when using the h/w to do
2250 * the MIC. For everything else, including software crypto,
2251 * we allocate a single entry. Note that s/w crypto requires
2252 * a pass-through slot on the 5211 and 5212. The 5210 does
2253 * not support pass-through cache entries and we map all
2254 * those requests to slot 0.
2256 if (k->wk_flags & IEEE80211_KEY_SWCRYPT) {
2257 return key_alloc_single(sc, keyix, rxkeyix);
2258 } else if (k->wk_cipher->ic_cipher == IEEE80211_CIPHER_TKIP &&
2259 (k->wk_flags & IEEE80211_KEY_SWMIC) == 0) {
2260 if (sc->sc_splitmic)
2261 return key_alloc_2pair(sc, keyix, rxkeyix);
2263 return key_alloc_pair(sc, keyix, rxkeyix);
2265 return key_alloc_single(sc, keyix, rxkeyix);
2270 * Delete an entry in the key cache allocated by ath_key_alloc.
2273 ath_key_delete(struct ieee80211vap *vap, const struct ieee80211_key *k)
2275 struct ath_softc *sc = vap->iv_ic->ic_ifp->if_softc;
2276 struct ath_hal *ah = sc->sc_ah;
2277 const struct ieee80211_cipher *cip = k->wk_cipher;
2278 u_int keyix = k->wk_keyix;
2280 DPRINTF(sc, ATH_DEBUG_KEYCACHE, "%s: delete key %u\n", __func__, keyix);
2282 ath_hal_keyreset(ah, keyix);
2284 * Handle split tx/rx keying required for TKIP with h/w MIC.
2286 if (cip->ic_cipher == IEEE80211_CIPHER_TKIP &&
2287 (k->wk_flags & IEEE80211_KEY_SWMIC) == 0 && sc->sc_splitmic)
2288 ath_hal_keyreset(ah, keyix+32); /* RX key */
2289 if (keyix >= IEEE80211_WEP_NKID) {
2291 * Don't touch keymap entries for global keys so
2292 * they are never considered for dynamic allocation.
2294 clrbit(sc->sc_keymap, keyix);
2295 if (cip->ic_cipher == IEEE80211_CIPHER_TKIP &&
2296 (k->wk_flags & IEEE80211_KEY_SWMIC) == 0) {
2297 clrbit(sc->sc_keymap, keyix+64); /* TX key MIC */
2298 if (sc->sc_splitmic) {
2299 /* +32 for RX key, +32+64 for RX key MIC */
2300 clrbit(sc->sc_keymap, keyix+32);
2301 clrbit(sc->sc_keymap, keyix+32+64);
2309 * Set the key cache contents for the specified key. Key cache
2310 * slot(s) must already have been allocated by ath_key_alloc.
2313 ath_key_set(struct ieee80211vap *vap, const struct ieee80211_key *k,
2314 const u_int8_t mac[IEEE80211_ADDR_LEN])
2316 struct ath_softc *sc = vap->iv_ic->ic_ifp->if_softc;
2318 return ath_keyset(sc, k, vap->iv_bss);
2322 * Block/unblock tx+rx processing while a key change is done.
2323 * We assume the caller serializes key management operations
2324 * so we only need to worry about synchronization with other
2325 * uses that originate in the driver.
2328 ath_key_update_begin(struct ieee80211vap *vap)
2330 struct ifnet *ifp = vap->iv_ic->ic_ifp;
2331 struct ath_softc *sc = ifp->if_softc;
2333 DPRINTF(sc, ATH_DEBUG_KEYCACHE, "%s:\n", __func__);
2334 taskqueue_block(sc->sc_tq);
2338 ath_key_update_end(struct ieee80211vap *vap)
2340 struct ifnet *ifp = vap->iv_ic->ic_ifp;
2341 struct ath_softc *sc = ifp->if_softc;
2343 DPRINTF(sc, ATH_DEBUG_KEYCACHE, "%s:\n", __func__);
2344 taskqueue_unblock(sc->sc_tq);
2348 * Calculate the receive filter according to the
2349 * operating mode and state:
2351 * o always accept unicast, broadcast, and multicast traffic
2352 * o accept PHY error frames when hardware doesn't have MIB support
2353 * to count and we need them for ANI (sta mode only until recently)
2354 * and we are not scanning (ANI is disabled)
2355 * NB: older hal's add rx filter bits out of sight and we need to
2356 * blindly preserve them
2357 * o probe request frames are accepted only when operating in
2358 * hostap, adhoc, mesh, or monitor modes
2359 * o enable promiscuous mode
2360 * - when in monitor mode
2361 * - if interface marked PROMISC (assumes bridge setting is filtered)
2363 * - when operating in station mode for collecting rssi data when
2364 * the station is otherwise quiet, or
2365 * - when operating in adhoc mode so the 802.11 layer creates
2366 * node table entries for peers,
2368 * - when doing s/w beacon miss (e.g. for ap+sta)
2369 * - when operating in ap mode in 11g to detect overlapping bss that
2370 * require protection
2371 * - when operating in mesh mode to detect neighbors
2372 * o accept control frames:
2373 * - when in monitor mode
2374 * XXX BAR frames for 11n
2375 * XXX HT protection for 11n
2378 ath_calcrxfilter(struct ath_softc *sc)
2380 struct ifnet *ifp = sc->sc_ifp;
2381 struct ieee80211com *ic = ifp->if_l2com;
2384 rfilt = HAL_RX_FILTER_UCAST | HAL_RX_FILTER_BCAST | HAL_RX_FILTER_MCAST;
2385 if (!sc->sc_needmib && !sc->sc_scanning)
2386 rfilt |= HAL_RX_FILTER_PHYERR;
2387 if (ic->ic_opmode != IEEE80211_M_STA)
2388 rfilt |= HAL_RX_FILTER_PROBEREQ;
2389 /* XXX ic->ic_monvaps != 0? */
2390 if (ic->ic_opmode == IEEE80211_M_MONITOR || (ifp->if_flags & IFF_PROMISC))
2391 rfilt |= HAL_RX_FILTER_PROM;
2392 if (ic->ic_opmode == IEEE80211_M_STA ||
2393 ic->ic_opmode == IEEE80211_M_IBSS ||
2394 sc->sc_swbmiss || sc->sc_scanning)
2395 rfilt |= HAL_RX_FILTER_BEACON;
2397 * NB: We don't recalculate the rx filter when
2398 * ic_protmode changes; otherwise we could do
2399 * this only when ic_protmode != NONE.
2401 if (ic->ic_opmode == IEEE80211_M_HOSTAP &&
2402 IEEE80211_IS_CHAN_ANYG(ic->ic_curchan))
2403 rfilt |= HAL_RX_FILTER_BEACON;
2404 if (sc->sc_nmeshvaps) {
2405 rfilt |= HAL_RX_FILTER_BEACON;
2406 if (sc->sc_hasbmatch)
2407 rfilt |= HAL_RX_FILTER_BSSID;
2409 rfilt |= HAL_RX_FILTER_PROM;
2411 if (ic->ic_opmode == IEEE80211_M_MONITOR)
2412 rfilt |= HAL_RX_FILTER_CONTROL;
2413 DPRINTF(sc, ATH_DEBUG_MODE, "%s: RX filter 0x%x, %s if_flags 0x%x\n",
2414 __func__, rfilt, ieee80211_opmode_name[ic->ic_opmode], ifp->if_flags);
2419 ath_update_promisc(struct ifnet *ifp)
2421 struct ath_softc *sc = ifp->if_softc;
2424 /* configure rx filter */
2425 rfilt = ath_calcrxfilter(sc);
2426 ath_hal_setrxfilter(sc->sc_ah, rfilt);
2428 DPRINTF(sc, ATH_DEBUG_MODE, "%s: RX filter 0x%x\n", __func__, rfilt);
2432 ath_update_mcast(struct ifnet *ifp)
2434 struct ath_softc *sc = ifp->if_softc;
2437 /* calculate and install multicast filter */
2438 if ((ifp->if_flags & IFF_ALLMULTI) == 0) {
2439 struct ifmultiaddr *ifma;
2441 * Merge multicast addresses to form the hardware filter.
2443 mfilt[0] = mfilt[1] = 0;
2445 if_maddr_rlock(ifp); /* XXX need some fiddling to remove? */
2447 TAILQ_FOREACH(ifma, &ifp->if_multiaddrs, ifma_link) {
2452 /* calculate XOR of eight 6bit values */
2453 dl = LLADDR((struct sockaddr_dl *) ifma->ifma_addr);
2454 val = LE_READ_4(dl + 0);
2455 pos = (val >> 18) ^ (val >> 12) ^ (val >> 6) ^ val;
2456 val = LE_READ_4(dl + 3);
2457 pos ^= (val >> 18) ^ (val >> 12) ^ (val >> 6) ^ val;
2459 mfilt[pos / 32] |= (1 << (pos % 32));
2462 if_maddr_runlock(ifp);
2465 mfilt[0] = mfilt[1] = ~0;
2466 ath_hal_setmcastfilter(sc->sc_ah, mfilt[0], mfilt[1]);
2467 DPRINTF(sc, ATH_DEBUG_MODE, "%s: MC filter %08x:%08x\n",
2468 __func__, mfilt[0], mfilt[1]);
2472 ath_mode_init(struct ath_softc *sc)
2474 struct ifnet *ifp = sc->sc_ifp;
2475 struct ath_hal *ah = sc->sc_ah;
2478 /* configure rx filter */
2479 rfilt = ath_calcrxfilter(sc);
2480 ath_hal_setrxfilter(ah, rfilt);
2482 /* configure operational mode */
2483 ath_hal_setopmode(ah);
2485 /* handle any link-level address change */
2486 ath_hal_setmac(ah, IF_LLADDR(ifp));
2488 /* calculate and install multicast filter */
2489 ath_update_mcast(ifp);
2493 * Set the slot time based on the current setting.
2496 ath_setslottime(struct ath_softc *sc)
2498 struct ieee80211com *ic = sc->sc_ifp->if_l2com;
2499 struct ath_hal *ah = sc->sc_ah;
2502 if (IEEE80211_IS_CHAN_HALF(ic->ic_curchan))
2504 else if (IEEE80211_IS_CHAN_QUARTER(ic->ic_curchan))
2506 else if (IEEE80211_IS_CHAN_ANYG(ic->ic_curchan)) {
2507 /* honor short/long slot time only in 11g */
2508 /* XXX shouldn't honor on pure g or turbo g channel */
2509 if (ic->ic_flags & IEEE80211_F_SHSLOT)
2510 usec = HAL_SLOT_TIME_9;
2512 usec = HAL_SLOT_TIME_20;
2514 usec = HAL_SLOT_TIME_9;
2516 DPRINTF(sc, ATH_DEBUG_RESET,
2517 "%s: chan %u MHz flags 0x%x %s slot, %u usec\n",
2518 __func__, ic->ic_curchan->ic_freq, ic->ic_curchan->ic_flags,
2519 ic->ic_flags & IEEE80211_F_SHSLOT ? "short" : "long", usec);
2521 ath_hal_setslottime(ah, usec);
2522 sc->sc_updateslot = OK;
2526 * Callback from the 802.11 layer to update the
2527 * slot time based on the current setting.
2530 ath_updateslot(struct ifnet *ifp)
2532 struct ath_softc *sc = ifp->if_softc;
2533 struct ieee80211com *ic = ifp->if_l2com;
2536 * When not coordinating the BSS, change the hardware
2537 * immediately. For other operation we defer the change
2538 * until beacon updates have propagated to the stations.
2540 if (ic->ic_opmode == IEEE80211_M_HOSTAP ||
2541 ic->ic_opmode == IEEE80211_M_MBSS)
2542 sc->sc_updateslot = UPDATE;
2544 ath_setslottime(sc);
2548 * Setup a h/w transmit queue for beacons.
2551 ath_beaconq_setup(struct ath_hal *ah)
2555 memset(&qi, 0, sizeof(qi));
2556 qi.tqi_aifs = HAL_TXQ_USEDEFAULT;
2557 qi.tqi_cwmin = HAL_TXQ_USEDEFAULT;
2558 qi.tqi_cwmax = HAL_TXQ_USEDEFAULT;
2559 /* NB: for dynamic turbo, don't enable any other interrupts */
2560 qi.tqi_qflags = HAL_TXQ_TXDESCINT_ENABLE;
2561 return ath_hal_setuptxqueue(ah, HAL_TX_QUEUE_BEACON, &qi);
2565 * Setup the transmit queue parameters for the beacon queue.
2568 ath_beaconq_config(struct ath_softc *sc)
2570 #define ATH_EXPONENT_TO_VALUE(v) ((1<<(v))-1)
2571 struct ieee80211com *ic = sc->sc_ifp->if_l2com;
2572 struct ath_hal *ah = sc->sc_ah;
2575 ath_hal_gettxqueueprops(ah, sc->sc_bhalq, &qi);
2576 if (ic->ic_opmode == IEEE80211_M_HOSTAP ||
2577 ic->ic_opmode == IEEE80211_M_MBSS) {
2579 * Always burst out beacon and CAB traffic.
2581 qi.tqi_aifs = ATH_BEACON_AIFS_DEFAULT;
2582 qi.tqi_cwmin = ATH_BEACON_CWMIN_DEFAULT;
2583 qi.tqi_cwmax = ATH_BEACON_CWMAX_DEFAULT;
2585 struct wmeParams *wmep =
2586 &ic->ic_wme.wme_chanParams.cap_wmeParams[WME_AC_BE];
2588 * Adhoc mode; important thing is to use 2x cwmin.
2590 qi.tqi_aifs = wmep->wmep_aifsn;
2591 qi.tqi_cwmin = 2*ATH_EXPONENT_TO_VALUE(wmep->wmep_logcwmin);
2592 qi.tqi_cwmax = ATH_EXPONENT_TO_VALUE(wmep->wmep_logcwmax);
2595 if (!ath_hal_settxqueueprops(ah, sc->sc_bhalq, &qi)) {
2596 device_printf(sc->sc_dev, "unable to update parameters for "
2597 "beacon hardware queue!\n");
2600 ath_hal_resettxqueue(ah, sc->sc_bhalq); /* push to h/w */
2603 #undef ATH_EXPONENT_TO_VALUE
2607 * Allocate and setup an initial beacon frame.
2610 ath_beacon_alloc(struct ath_softc *sc, struct ieee80211_node *ni)
2612 struct ieee80211vap *vap = ni->ni_vap;
2613 struct ath_vap *avp = ATH_VAP(vap);
2619 if (bf->bf_m != NULL) {
2620 bus_dmamap_unload(sc->sc_dmat, bf->bf_dmamap);
2624 if (bf->bf_node != NULL) {
2625 ieee80211_free_node(bf->bf_node);
2630 * NB: the beacon data buffer must be 32-bit aligned;
2631 * we assume the mbuf routines will return us something
2632 * with this alignment (perhaps should assert).
2634 m = ieee80211_beacon_alloc(ni, &avp->av_boff);
2636 device_printf(sc->sc_dev, "%s: cannot get mbuf\n", __func__);
2637 sc->sc_stats.ast_be_nombuf++;
2640 error = bus_dmamap_load_mbuf_segment(sc->sc_dmat, bf->bf_dmamap, m,
2641 bf->bf_segs, 1, &bf->bf_nseg,
2644 device_printf(sc->sc_dev,
2645 "%s: cannot map mbuf, bus_dmamap_load_mbuf_segment returns %d\n",
2652 * Calculate a TSF adjustment factor required for staggered
2653 * beacons. Note that we assume the format of the beacon
2654 * frame leaves the tstamp field immediately following the
2657 if (sc->sc_stagbeacons && avp->av_bslot > 0) {
2659 struct ieee80211_frame *wh;
2662 * The beacon interval is in TU's; the TSF is in usecs.
2663 * We figure out how many TU's to add to align the timestamp
2664 * then convert to TSF units and handle byte swapping before
2665 * inserting it in the frame. The hardware will then add this
2666 * each time a beacon frame is sent. Note that we align vap's
2667 * 1..N and leave vap 0 untouched. This means vap 0 has a
2668 * timestamp in one beacon interval while the others get a
2669 * timstamp aligned to the next interval.
2671 tsfadjust = ni->ni_intval *
2672 (ATH_BCBUF - avp->av_bslot) / ATH_BCBUF;
2673 tsfadjust = htole64(tsfadjust << 10); /* TU -> TSF */
2675 DPRINTF(sc, ATH_DEBUG_BEACON,
2676 "%s: %s beacons bslot %d intval %u tsfadjust %llu\n",
2677 __func__, sc->sc_stagbeacons ? "stagger" : "burst",
2678 avp->av_bslot, ni->ni_intval,
2679 (long long unsigned) le64toh(tsfadjust));
2681 wh = mtod(m, struct ieee80211_frame *);
2682 memcpy(&wh[1], &tsfadjust, sizeof(tsfadjust));
2685 bf->bf_node = ieee80211_ref_node(ni);
2691 * Setup the beacon frame for transmit.
2694 ath_beacon_setup(struct ath_softc *sc, struct ath_buf *bf)
2696 #define USE_SHPREAMBLE(_ic) \
2697 (((_ic)->ic_flags & (IEEE80211_F_SHPREAMBLE | IEEE80211_F_USEBARKER))\
2698 == IEEE80211_F_SHPREAMBLE)
2699 struct ieee80211_node *ni = bf->bf_node;
2700 struct ieee80211com *ic = ni->ni_ic;
2701 struct mbuf *m = bf->bf_m;
2702 struct ath_hal *ah = sc->sc_ah;
2703 struct ath_desc *ds;
2705 const HAL_RATE_TABLE *rt;
2708 DPRINTF(sc, ATH_DEBUG_BEACON_PROC, "%s: m %p len %u\n",
2709 __func__, m, m->m_len);
2711 /* setup descriptors */
2714 flags = HAL_TXDESC_NOACK;
2715 if (ic->ic_opmode == IEEE80211_M_IBSS && sc->sc_hasveol) {
2716 ds->ds_link = bf->bf_daddr; /* self-linked */
2717 flags |= HAL_TXDESC_VEOL;
2719 * Let hardware handle antenna switching.
2721 antenna = sc->sc_txantenna;
2725 * Switch antenna every 4 beacons.
2726 * XXX assumes two antenna
2728 if (sc->sc_txantenna != 0)
2729 antenna = sc->sc_txantenna;
2730 else if (sc->sc_stagbeacons && sc->sc_nbcnvaps != 0)
2731 antenna = ((sc->sc_stats.ast_be_xmit / sc->sc_nbcnvaps) & 4 ? 2 : 1);
2733 antenna = (sc->sc_stats.ast_be_xmit & 4 ? 2 : 1);
2736 KASSERT(bf->bf_nseg == 1,
2737 ("multi-segment beacon frame; nseg %u", bf->bf_nseg));
2738 ds->ds_data = bf->bf_segs[0].ds_addr;
2740 * Calculate rate code.
2741 * XXX everything at min xmit rate
2744 rt = sc->sc_currates;
2745 rate = rt->info[rix].rateCode;
2746 if (USE_SHPREAMBLE(ic))
2747 rate |= rt->info[rix].shortPreamble;
2748 ath_hal_setuptxdesc(ah, ds
2749 , m->m_len + IEEE80211_CRC_LEN /* frame length */
2750 , sizeof(struct ieee80211_frame)/* header length */
2751 , HAL_PKT_TYPE_BEACON /* Atheros packet type */
2752 , ni->ni_txpower /* txpower XXX */
2753 , rate, 1 /* series 0 rate/tries */
2754 , HAL_TXKEYIX_INVALID /* no encryption */
2755 , antenna /* antenna mode */
2756 , flags /* no ack, veol for beacons */
2757 , 0 /* rts/cts rate */
2758 , 0 /* rts/cts duration */
2760 /* NB: beacon's BufLen must be a multiple of 4 bytes */
2761 ath_hal_filltxdesc(ah, ds
2762 , roundup(m->m_len, 4) /* buffer length */
2763 , AH_TRUE /* first segment */
2764 , AH_TRUE /* last segment */
2765 , ds /* first descriptor */
2770 #undef USE_SHPREAMBLE
2774 ath_beacon_update(struct ieee80211vap *vap, int item)
2776 struct ieee80211_beacon_offsets *bo = &ATH_VAP(vap)->av_boff;
2778 setbit(bo->bo_flags, item);
2782 * Append the contents of src to dst; both queues
2783 * are assumed to be locked.
2786 ath_txqmove(struct ath_txq *dst, struct ath_txq *src)
2788 STAILQ_CONCAT(&dst->axq_q, &src->axq_q);
2790 dst->axq_link = src->axq_link;
2791 src->axq_link = NULL;
2792 dst->axq_depth += src->axq_depth;
2797 * Transmit a beacon frame at SWBA. Dynamic updates to the
2798 * frame contents are done as needed and the slot time is
2799 * also adjusted based on current state.
2802 ath_beacon_proc(void *arg, int pending)
2804 struct ath_softc *sc = arg;
2805 struct ath_hal *ah = sc->sc_ah;
2806 struct ieee80211vap *vap;
2811 DPRINTF(sc, ATH_DEBUG_BEACON_PROC, "%s: pending %u\n",
2814 * Check if the previous beacon has gone out. If
2815 * not don't try to post another, skip this period
2816 * and wait for the next. Missed beacons indicate
2817 * a problem and should not occur. If we miss too
2818 * many consecutive beacons reset the device.
2820 if (ath_hal_numtxpending(ah, sc->sc_bhalq) != 0) {
2821 sc->sc_bmisscount++;
2822 DPRINTF(sc, ATH_DEBUG_BEACON,
2823 "%s: missed %u consecutive beacons\n",
2824 __func__, sc->sc_bmisscount);
2825 if (sc->sc_bmisscount >= ath_bstuck_threshold)
2826 taskqueue_enqueue(sc->sc_tq, &sc->sc_bstucktask);
2829 if (sc->sc_bmisscount != 0) {
2830 DPRINTF(sc, ATH_DEBUG_BEACON,
2831 "%s: resume beacon xmit after %u misses\n",
2832 __func__, sc->sc_bmisscount);
2833 sc->sc_bmisscount = 0;
2837 * Stop any current dma before messing with the beacon linkages.
2839 if (!ath_hal_stoptxdma(ah, sc->sc_bhalq)) {
2840 DPRINTF(sc, ATH_DEBUG_ANY,
2841 "%s: beacon queue %u did not stop?\n",
2842 __func__, sc->sc_bhalq);
2845 if (sc->sc_stagbeacons) { /* staggered beacons */
2846 struct ieee80211com *ic = sc->sc_ifp->if_l2com;
2849 tsftu = ath_hal_gettsf32(ah) >> 10;
2851 slot = ((tsftu % ic->ic_lintval) * ATH_BCBUF) / ic->ic_lintval;
2852 vap = sc->sc_bslot[(slot+1) % ATH_BCBUF];
2854 if (vap != NULL && vap->iv_state >= IEEE80211_S_RUN) {
2855 bf = ath_beacon_generate(sc, vap);
2857 bfaddr = bf->bf_daddr;
2859 } else { /* burst'd beacons */
2860 uint32_t *bflink = &bfaddr;
2862 for (slot = 0; slot < ATH_BCBUF; slot++) {
2863 vap = sc->sc_bslot[slot];
2864 if (vap != NULL && vap->iv_state >= IEEE80211_S_RUN) {
2865 bf = ath_beacon_generate(sc, vap);
2867 *bflink = bf->bf_daddr;
2868 bflink = &bf->bf_desc->ds_link;
2872 *bflink = 0; /* terminate list */
2876 * Handle slot time change when a non-ERP station joins/leaves
2877 * an 11g network. The 802.11 layer notifies us via callback,
2878 * we mark updateslot, then wait one beacon before effecting
2879 * the change. This gives associated stations at least one
2880 * beacon interval to note the state change.
2883 if (sc->sc_updateslot == UPDATE) {
2884 sc->sc_updateslot = COMMIT; /* commit next beacon */
2885 sc->sc_slotupdate = slot;
2886 } else if (sc->sc_updateslot == COMMIT && sc->sc_slotupdate == slot)
2887 ath_setslottime(sc); /* commit change to h/w */
2890 * Check recent per-antenna transmit statistics and flip
2891 * the default antenna if noticeably more frames went out
2892 * on the non-default antenna.
2893 * XXX assumes 2 anntenae
2895 if (!sc->sc_diversity && (!sc->sc_stagbeacons || slot == 0)) {
2896 otherant = sc->sc_defant & 1 ? 2 : 1;
2897 if (sc->sc_ant_tx[otherant] > sc->sc_ant_tx[sc->sc_defant] + 2)
2898 ath_setdefantenna(sc, otherant);
2899 sc->sc_ant_tx[1] = sc->sc_ant_tx[2] = 0;
2903 /* NB: cabq traffic should already be queued and primed */
2904 ath_hal_puttxbuf(ah, sc->sc_bhalq, bfaddr);
2905 sc->sc_stats.ast_be_xmit++;
2906 ath_hal_txstart(ah, sc->sc_bhalq);
2908 /* else no beacon will be generated */
2911 static struct ath_buf *
2912 ath_beacon_generate(struct ath_softc *sc, struct ieee80211vap *vap)
2914 struct ath_vap *avp = ATH_VAP(vap);
2915 struct ath_txq *cabq = sc->sc_cabq;
2920 KASSERT(vap->iv_state >= IEEE80211_S_RUN,
2921 ("not running, state %d", vap->iv_state));
2922 KASSERT(avp->av_bcbuf != NULL, ("no beacon buffer"));
2925 * Update dynamic beacon contents. If this returns
2926 * non-zero then we need to remap the memory because
2927 * the beacon frame changed size (probably because
2928 * of the TIM bitmap).
2932 nmcastq = avp->av_mcastq.axq_depth;
2933 if (ieee80211_beacon_update(bf->bf_node, &avp->av_boff, m, nmcastq)) {
2934 /* XXX too conservative? */
2935 bus_dmamap_unload(sc->sc_dmat, bf->bf_dmamap);
2936 error = bus_dmamap_load_mbuf_segment(sc->sc_dmat, bf->bf_dmamap, m,
2937 bf->bf_segs, 1, &bf->bf_nseg,
2940 if_printf(vap->iv_ifp,
2941 "%s: bus_dmamap_load_mbuf_segment failed, error %u\n",
2946 if ((avp->av_boff.bo_tim[4] & 1) && cabq->axq_depth) {
2947 DPRINTF(sc, ATH_DEBUG_BEACON,
2948 "%s: cabq did not drain, mcastq %u cabq %u\n",
2949 __func__, nmcastq, cabq->axq_depth);
2950 sc->sc_stats.ast_cabq_busy++;
2951 if (sc->sc_nvaps > 1 && sc->sc_stagbeacons) {
2953 * CABQ traffic from a previous vap is still pending.
2954 * We must drain the q before this beacon frame goes
2955 * out as otherwise this vap's stations will get cab
2956 * frames from a different vap.
2957 * XXX could be slow causing us to miss DBA
2959 ath_tx_draintxq(sc, cabq);
2962 ath_beacon_setup(sc, bf);
2963 bus_dmamap_sync(sc->sc_dmat, bf->bf_dmamap, BUS_DMASYNC_PREWRITE);
2966 * Enable the CAB queue before the beacon queue to
2967 * insure cab frames are triggered by this beacon.
2969 if (avp->av_boff.bo_tim[4] & 1) {
2970 struct ath_hal *ah = sc->sc_ah;
2972 /* NB: only at DTIM */
2974 struct ath_buf *bfm;
2978 * Move frames from the s/w mcast q to the h/w cab q.
2981 bfm = STAILQ_FIRST(&avp->av_mcastq.axq_q);
2982 qbusy = ath_hal_txqenabled(ah, cabq->axq_qnum);
2984 if (cabq->axq_link != NULL) {
2986 *cabq->axq_link = bfm->bf_daddr;
2987 cabq->axq_flags |= ATH_TXQ_PUTPENDING;
2990 ath_hal_puttxbuf(ah, cabq->axq_qnum,
2994 if (cabq->axq_link != NULL) {
2996 *cabq->axq_link = bfm->bf_daddr;
2998 cabq->axq_flags |= ATH_TXQ_PUTPENDING;
3000 ath_txqmove(cabq, &avp->av_mcastq);
3002 sc->sc_stats.ast_cabq_xmit += nmcastq;
3004 /* NB: gated by beacon so safe to start here */
3005 ath_hal_txstart(ah, cabq->axq_qnum);
3011 ath_beacon_start_adhoc(struct ath_softc *sc, struct ieee80211vap *vap)
3013 struct ath_vap *avp = ATH_VAP(vap);
3014 struct ath_hal *ah = sc->sc_ah;
3019 KASSERT(avp->av_bcbuf != NULL, ("no beacon buffer"));
3022 * Update dynamic beacon contents. If this returns
3023 * non-zero then we need to remap the memory because
3024 * the beacon frame changed size (probably because
3025 * of the TIM bitmap).
3029 if (ieee80211_beacon_update(bf->bf_node, &avp->av_boff, m, 0)) {
3030 /* XXX too conservative? */
3031 bus_dmamap_unload(sc->sc_dmat, bf->bf_dmamap);
3032 error = bus_dmamap_load_mbuf_segment(sc->sc_dmat, bf->bf_dmamap, m,
3033 bf->bf_segs, 1, &bf->bf_nseg,
3036 if_printf(vap->iv_ifp,
3037 "%s: bus_dmamap_load_mbuf_segment failed, error %u\n",
3042 ath_beacon_setup(sc, bf);
3043 bus_dmamap_sync(sc->sc_dmat, bf->bf_dmamap, BUS_DMASYNC_PREWRITE);
3045 /* NB: caller is known to have already stopped tx dma */
3046 ath_hal_puttxbuf(ah, sc->sc_bhalq, bf->bf_daddr);
3047 ath_hal_txstart(ah, sc->sc_bhalq);
3051 * Reset the hardware after detecting beacons have stopped.
3054 ath_bstuck_task(void *arg, int pending)
3056 struct ath_softc *sc = arg;
3057 struct ifnet *ifp = sc->sc_ifp;
3059 wlan_serialize_enter();
3060 if_printf(ifp, "stuck beacon; resetting (bmiss count %u)\n",
3062 sc->sc_stats.ast_bstuck++;
3064 wlan_serialize_exit();
3068 * Reclaim beacon resources and return buffer to the pool.
3071 ath_beacon_return(struct ath_softc *sc, struct ath_buf *bf)
3074 if (bf->bf_m != NULL) {
3075 bus_dmamap_unload(sc->sc_dmat, bf->bf_dmamap);
3079 if (bf->bf_node != NULL) {
3080 ieee80211_free_node(bf->bf_node);
3083 STAILQ_INSERT_TAIL(&sc->sc_bbuf, bf, bf_list);
3087 * Reclaim beacon resources.
3090 ath_beacon_free(struct ath_softc *sc)
3094 STAILQ_FOREACH(bf, &sc->sc_bbuf, bf_list) {
3095 if (bf->bf_m != NULL) {
3096 bus_dmamap_unload(sc->sc_dmat, bf->bf_dmamap);
3100 if (bf->bf_node != NULL) {
3101 ieee80211_free_node(bf->bf_node);
3108 * Configure the beacon and sleep timers.
3110 * When operating as an AP this resets the TSF and sets
3111 * up the hardware to notify us when we need to issue beacons.
3113 * When operating in station mode this sets up the beacon
3114 * timers according to the timestamp of the last received
3115 * beacon and the current TSF, configures PCF and DTIM
3116 * handling, programs the sleep registers so the hardware
3117 * will wakeup in time to receive beacons, and configures
3118 * the beacon miss handling so we'll receive a BMISS
3119 * interrupt when we stop seeing beacons from the AP
3120 * we've associated with.
3123 ath_beacon_config(struct ath_softc *sc, struct ieee80211vap *vap)
3125 #define TSF_TO_TU(_h,_l) \
3126 ((((u_int32_t)(_h)) << 22) | (((u_int32_t)(_l)) >> 10))
3128 struct ath_hal *ah = sc->sc_ah;
3129 struct ieee80211com *ic = sc->sc_ifp->if_l2com;
3130 struct ieee80211_node *ni;
3131 u_int32_t nexttbtt, intval, tsftu;
3135 vap = TAILQ_FIRST(&ic->ic_vaps); /* XXX */
3138 /* extract tstamp from last beacon and convert to TU */
3139 nexttbtt = TSF_TO_TU(LE_READ_4(ni->ni_tstamp.data + 4),
3140 LE_READ_4(ni->ni_tstamp.data));
3141 if (ic->ic_opmode == IEEE80211_M_HOSTAP ||
3142 ic->ic_opmode == IEEE80211_M_MBSS) {
3144 * For multi-bss ap/mesh support beacons are either staggered
3145 * evenly over N slots or burst together. For the former
3146 * arrange for the SWBA to be delivered for each slot.
3147 * Slots that are not occupied will generate nothing.
3149 /* NB: the beacon interval is kept internally in TU's */
3150 intval = ni->ni_intval & HAL_BEACON_PERIOD;
3151 if (sc->sc_stagbeacons)
3152 intval /= ATH_BCBUF;
3154 /* NB: the beacon interval is kept internally in TU's */
3155 intval = ni->ni_intval & HAL_BEACON_PERIOD;
3157 if (nexttbtt == 0) /* e.g. for ap mode */
3159 else if (intval) /* NB: can be 0 for monitor mode */
3160 nexttbtt = roundup(nexttbtt, intval);
3161 DPRINTF(sc, ATH_DEBUG_BEACON, "%s: nexttbtt %u intval %u (%u)\n",
3162 __func__, nexttbtt, intval, ni->ni_intval);
3163 if (ic->ic_opmode == IEEE80211_M_STA && !sc->sc_swbmiss) {
3164 HAL_BEACON_STATE bs;
3165 int dtimperiod, dtimcount;
3166 int cfpperiod, cfpcount;
3169 * Setup dtim and cfp parameters according to
3170 * last beacon we received (which may be none).
3172 dtimperiod = ni->ni_dtim_period;
3173 if (dtimperiod <= 0) /* NB: 0 if not known */
3175 dtimcount = ni->ni_dtim_count;
3176 if (dtimcount >= dtimperiod) /* NB: sanity check */
3177 dtimcount = 0; /* XXX? */
3178 cfpperiod = 1; /* NB: no PCF support yet */
3181 * Pull nexttbtt forward to reflect the current
3182 * TSF and calculate dtim+cfp state for the result.
3184 tsf = ath_hal_gettsf64(ah);
3185 tsftu = TSF_TO_TU(tsf>>32, tsf) + FUDGE;
3188 if (--dtimcount < 0) {
3189 dtimcount = dtimperiod - 1;
3191 cfpcount = cfpperiod - 1;
3193 } while (nexttbtt < tsftu);
3194 memset(&bs, 0, sizeof(bs));
3195 bs.bs_intval = intval;
3196 bs.bs_nexttbtt = nexttbtt;
3197 bs.bs_dtimperiod = dtimperiod*intval;
3198 bs.bs_nextdtim = bs.bs_nexttbtt + dtimcount*intval;
3199 bs.bs_cfpperiod = cfpperiod*bs.bs_dtimperiod;
3200 bs.bs_cfpnext = bs.bs_nextdtim + cfpcount*bs.bs_dtimperiod;
3201 bs.bs_cfpmaxduration = 0;
3204 * The 802.11 layer records the offset to the DTIM
3205 * bitmap while receiving beacons; use it here to
3206 * enable h/w detection of our AID being marked in
3207 * the bitmap vector (to indicate frames for us are
3208 * pending at the AP).
3209 * XXX do DTIM handling in s/w to WAR old h/w bugs
3210 * XXX enable based on h/w rev for newer chips
3212 bs.bs_timoffset = ni->ni_timoff;
3215 * Calculate the number of consecutive beacons to miss
3216 * before taking a BMISS interrupt.
3217 * Note that we clamp the result to at most 10 beacons.
3219 bs.bs_bmissthreshold = vap->iv_bmissthreshold;
3220 if (bs.bs_bmissthreshold > 10)
3221 bs.bs_bmissthreshold = 10;
3222 else if (bs.bs_bmissthreshold <= 0)
3223 bs.bs_bmissthreshold = 1;
3226 * Calculate sleep duration. The configuration is
3227 * given in ms. We insure a multiple of the beacon
3228 * period is used. Also, if the sleep duration is
3229 * greater than the DTIM period then it makes senses
3230 * to make it a multiple of that.
3232 * XXX fixed at 100ms
3234 bs.bs_sleepduration =
3235 roundup(IEEE80211_MS_TO_TU(100), bs.bs_intval);
3236 if (bs.bs_sleepduration > bs.bs_dtimperiod)
3237 bs.bs_sleepduration = roundup(bs.bs_sleepduration, bs.bs_dtimperiod);
3239 DPRINTF(sc, ATH_DEBUG_BEACON,
3240 "%s: tsf %ju tsf:tu %u intval %u nexttbtt %u dtim %u nextdtim %u bmiss %u sleep %u cfp:period %u maxdur %u next %u timoffset %u\n"
3247 , bs.bs_bmissthreshold
3248 , bs.bs_sleepduration
3250 , bs.bs_cfpmaxduration
3254 ath_hal_intrset(ah, 0);
3255 ath_hal_beacontimers(ah, &bs);
3256 sc->sc_imask |= HAL_INT_BMISS;
3257 ath_hal_intrset(ah, sc->sc_imask);
3259 ath_hal_intrset(ah, 0);
3260 if (nexttbtt == intval)
3261 intval |= HAL_BEACON_RESET_TSF;
3262 if (ic->ic_opmode == IEEE80211_M_IBSS) {
3264 * In IBSS mode enable the beacon timers but only
3265 * enable SWBA interrupts if we need to manually
3266 * prepare beacon frames. Otherwise we use a
3267 * self-linked tx descriptor and let the hardware
3270 intval |= HAL_BEACON_ENA;
3271 if (!sc->sc_hasveol)
3272 sc->sc_imask |= HAL_INT_SWBA;
3273 if ((intval & HAL_BEACON_RESET_TSF) == 0) {
3275 * Pull nexttbtt forward to reflect
3278 tsf = ath_hal_gettsf64(ah);
3279 tsftu = TSF_TO_TU(tsf>>32, tsf) + FUDGE;
3282 } while (nexttbtt < tsftu);
3284 ath_beaconq_config(sc);
3285 } else if (ic->ic_opmode == IEEE80211_M_HOSTAP ||
3286 ic->ic_opmode == IEEE80211_M_MBSS) {
3288 * In AP/mesh mode we enable the beacon timers
3289 * and SWBA interrupts to prepare beacon frames.
3291 intval |= HAL_BEACON_ENA;
3292 sc->sc_imask |= HAL_INT_SWBA; /* beacon prepare */
3293 ath_beaconq_config(sc);
3295 ath_hal_beaconinit(ah, nexttbtt, intval);
3296 sc->sc_bmisscount = 0;
3297 ath_hal_intrset(ah, sc->sc_imask);
3299 * When using a self-linked beacon descriptor in
3300 * ibss mode load it once here.
3302 if (ic->ic_opmode == IEEE80211_M_IBSS && sc->sc_hasveol)
3303 ath_beacon_start_adhoc(sc, vap);
3305 sc->sc_syncbeacon = 0;
3311 ath_load_cb(void *arg, bus_dma_segment_t *segs, int nsegs, int error)
3313 bus_addr_t *paddr = (bus_addr_t*) arg;
3314 KASSERT(error == 0, ("error %u on bus_dma callback", error));
3315 *paddr = segs->ds_addr;
3319 ath_descdma_setup(struct ath_softc *sc,
3320 struct ath_descdma *dd, ath_bufhead *head,
3321 const char *name, int nbuf, int ndesc)
3323 #define DS2PHYS(_dd, _ds) \
3324 ((_dd)->dd_desc_paddr + ((caddr_t)(_ds) - (caddr_t)(_dd)->dd_desc))
3325 struct ifnet *ifp = sc->sc_ifp;
3326 struct ath_desc *ds;
3328 int i, bsize, error;
3330 DPRINTF(sc, ATH_DEBUG_RESET, "%s: %s DMA: %u buffers %u desc/buf\n",
3331 __func__, name, nbuf, ndesc);
3334 dd->dd_desc_len = sizeof(struct ath_desc) * nbuf * ndesc;
3337 * Setup DMA descriptor area.
3339 error = bus_dma_tag_create(dd->dd_dmat, /* parent */
3340 PAGE_SIZE, 0, /* alignment, bounds */
3341 BUS_SPACE_MAXADDR_32BIT, /* lowaddr */
3342 BUS_SPACE_MAXADDR, /* highaddr */
3343 NULL, NULL, /* filter, filterarg */
3344 dd->dd_desc_len, /* maxsize */
3346 dd->dd_desc_len, /* maxsegsize */
3347 BUS_DMA_ALLOCNOW, /* flags */
3350 if_printf(ifp, "cannot allocate %s DMA tag\n", dd->dd_name);
3354 /* allocate descriptors */
3355 error = bus_dmamap_create(dd->dd_dmat, BUS_DMA_NOWAIT, &dd->dd_dmamap);
3357 if_printf(ifp, "unable to create dmamap for %s descriptors, "
3358 "error %u\n", dd->dd_name, error);
3362 error = bus_dmamem_alloc(dd->dd_dmat, (void**) &dd->dd_desc,
3363 BUS_DMA_NOWAIT | BUS_DMA_COHERENT,
3366 if_printf(ifp, "unable to alloc memory for %u %s descriptors, "
3367 "error %u\n", nbuf * ndesc, dd->dd_name, error);
3371 error = bus_dmamap_load(dd->dd_dmat, dd->dd_dmamap,
3372 dd->dd_desc, dd->dd_desc_len,
3373 ath_load_cb, &dd->dd_desc_paddr,
3376 if_printf(ifp, "unable to map %s descriptors, error %u\n",
3377 dd->dd_name, error);
3382 DPRINTF(sc, ATH_DEBUG_RESET, "%s: %s DMA map: %p (%lu) -> %p (%lu)\n",
3383 __func__, dd->dd_name, ds, (u_long) dd->dd_desc_len,
3384 (caddr_t) dd->dd_desc_paddr, /*XXX*/ (u_long) dd->dd_desc_len);
3386 /* allocate rx buffers */
3387 bsize = sizeof(struct ath_buf) * nbuf;
3388 bf = kmalloc(bsize, M_ATHDEV, M_INTWAIT | M_ZERO);
3390 if_printf(ifp, "malloc of %s buffers failed, size %u\n",
3391 dd->dd_name, bsize);
3397 for (i = 0; i < nbuf; i++, bf++, ds += ndesc) {
3399 bf->bf_daddr = DS2PHYS(dd, ds);
3400 error = bus_dmamap_create(sc->sc_dmat, BUS_DMA_NOWAIT,
3403 if_printf(ifp, "unable to create dmamap for %s "
3404 "buffer %u, error %u\n", dd->dd_name, i, error);
3405 ath_descdma_cleanup(sc, dd, head);
3408 STAILQ_INSERT_TAIL(head, bf, bf_list);
3412 bus_dmamap_unload(dd->dd_dmat, dd->dd_dmamap);
3414 bus_dmamem_free(dd->dd_dmat, dd->dd_desc, dd->dd_dmamap);
3416 bus_dmamap_destroy(dd->dd_dmat, dd->dd_dmamap);
3418 bus_dma_tag_destroy(dd->dd_dmat);
3419 memset(dd, 0, sizeof(*dd));
3425 ath_descdma_cleanup(struct ath_softc *sc,
3426 struct ath_descdma *dd, ath_bufhead *head)
3429 struct ieee80211_node *ni;
3431 bus_dmamap_unload(dd->dd_dmat, dd->dd_dmamap);
3432 bus_dmamem_free(dd->dd_dmat, dd->dd_desc, dd->dd_dmamap);
3433 bus_dmamap_destroy(dd->dd_dmat, dd->dd_dmamap);
3434 bus_dma_tag_destroy(dd->dd_dmat);
3436 STAILQ_FOREACH(bf, head, bf_list) {
3441 if (bf->bf_dmamap != NULL) {
3442 bus_dmamap_destroy(sc->sc_dmat, bf->bf_dmamap);
3443 bf->bf_dmamap = NULL;
3449 * Reclaim node reference.
3451 ieee80211_free_node(ni);
3456 kfree(dd->dd_bufptr, M_ATHDEV);
3457 memset(dd, 0, sizeof(*dd));
3461 ath_desc_alloc(struct ath_softc *sc)
3465 error = ath_descdma_setup(sc, &sc->sc_rxdma, &sc->sc_rxbuf,
3466 "rx", ath_rxbuf, 1);
3470 error = ath_descdma_setup(sc, &sc->sc_txdma, &sc->sc_txbuf,
3471 "tx", ath_txbuf, ATH_TXDESC);
3473 ath_descdma_cleanup(sc, &sc->sc_rxdma, &sc->sc_rxbuf);
3477 error = ath_descdma_setup(sc, &sc->sc_bdma, &sc->sc_bbuf,
3478 "beacon", ATH_BCBUF, 1);
3480 ath_descdma_cleanup(sc, &sc->sc_txdma, &sc->sc_txbuf);
3481 ath_descdma_cleanup(sc, &sc->sc_rxdma, &sc->sc_rxbuf);
3488 ath_desc_free(struct ath_softc *sc)
3491 if (sc->sc_bdma.dd_desc_len != 0)
3492 ath_descdma_cleanup(sc, &sc->sc_bdma, &sc->sc_bbuf);
3493 if (sc->sc_txdma.dd_desc_len != 0)
3494 ath_descdma_cleanup(sc, &sc->sc_txdma, &sc->sc_txbuf);
3495 if (sc->sc_rxdma.dd_desc_len != 0)
3496 ath_descdma_cleanup(sc, &sc->sc_rxdma, &sc->sc_rxbuf);
3499 static struct ieee80211_node *
3500 ath_node_alloc(struct ieee80211vap *vap, const uint8_t mac[IEEE80211_ADDR_LEN])
3502 struct ieee80211com *ic = vap->iv_ic;
3503 struct ath_softc *sc = ic->ic_ifp->if_softc;
3504 const size_t space = sizeof(struct ath_node) + sc->sc_rc->arc_space;
3505 struct ath_node *an;
3507 an = kmalloc(space, M_80211_NODE, M_INTWAIT|M_ZERO);
3512 ath_rate_node_init(sc, an);
3514 DPRINTF(sc, ATH_DEBUG_NODE, "%s: an %p\n", __func__, an);
3515 return &an->an_node;
3519 ath_node_free(struct ieee80211_node *ni)
3521 struct ieee80211com *ic = ni->ni_ic;
3522 struct ath_softc *sc = ic->ic_ifp->if_softc;
3524 DPRINTF(sc, ATH_DEBUG_NODE, "%s: ni %p\n", __func__, ni);
3526 ath_rate_node_cleanup(sc, ATH_NODE(ni));
3527 sc->sc_node_free(ni);
3531 ath_node_getsignal(const struct ieee80211_node *ni, int8_t *rssi, int8_t *noise)
3533 struct ieee80211com *ic = ni->ni_ic;
3534 struct ath_softc *sc = ic->ic_ifp->if_softc;
3535 struct ath_hal *ah = sc->sc_ah;
3537 *rssi = ic->ic_node_getrssi(ni);
3538 if (ni->ni_chan != IEEE80211_CHAN_ANYC)
3539 *noise = ath_hal_getchannoise(ah, ni->ni_chan);
3541 *noise = -95; /* nominally correct */
3545 ath_rxbuf_init(struct ath_softc *sc, struct ath_buf *bf)
3547 struct ath_hal *ah = sc->sc_ah;
3550 struct ath_desc *ds;
3555 * NB: by assigning a page to the rx dma buffer we
3556 * implicitly satisfy the Atheros requirement that
3557 * this buffer be cache-line-aligned and sized to be
3558 * multiple of the cache line size. Not doing this
3559 * causes weird stuff to happen (for the 5210 at least).
3561 m = m_getcl(MB_WAIT, MT_DATA, M_PKTHDR);
3563 kprintf("ath_rxbuf_init: no mbuf\n");
3564 DPRINTF(sc, ATH_DEBUG_ANY,
3565 "%s: no mbuf/cluster\n", __func__);
3566 sc->sc_stats.ast_rx_nombuf++;
3569 m->m_pkthdr.len = m->m_len = m->m_ext.ext_size;
3571 error = bus_dmamap_load_mbuf_segment(sc->sc_dmat,
3573 bf->bf_segs, 1, &bf->bf_nseg,
3576 DPRINTF(sc, ATH_DEBUG_ANY,
3577 "%s: bus_dmamap_load_mbuf_segment failed; error %d\n",
3579 sc->sc_stats.ast_rx_busdma++;
3583 KASSERT(bf->bf_nseg == 1,
3584 ("multi-segment packet; nseg %u", bf->bf_nseg));
3587 bus_dmamap_sync(sc->sc_dmat, bf->bf_dmamap, BUS_DMASYNC_PREREAD);
3590 * Setup descriptors. For receive we always terminate
3591 * the descriptor list with a self-linked entry so we'll
3592 * not get overrun under high load (as can happen with a
3593 * 5212 when ANI processing enables PHY error frames).
3595 * To insure the last descriptor is self-linked we create
3596 * each descriptor as self-linked and add it to the end. As
3597 * each additional descriptor is added the previous self-linked
3598 * entry is ``fixed'' naturally. This should be safe even
3599 * if DMA is happening. When processing RX interrupts we
3600 * never remove/process the last, self-linked, entry on the
3601 * descriptor list. This insures the hardware always has
3602 * someplace to write a new frame.
3605 ds->ds_link = bf->bf_daddr; /* link to self */
3606 ds->ds_data = bf->bf_segs[0].ds_addr;
3607 ath_hal_setuprxdesc(ah, ds
3608 , m->m_len /* buffer size */
3612 if (sc->sc_rxlink != NULL)
3613 *sc->sc_rxlink = bf->bf_daddr;
3614 sc->sc_rxlink = &ds->ds_link;
3619 * Extend 15-bit time stamp from rx descriptor to
3620 * a full 64-bit TSF using the specified TSF.
3622 static __inline u_int64_t
3623 ath_extend_tsf(u_int32_t rstamp, u_int64_t tsf)
3625 if ((tsf & 0x7fff) < rstamp)
3627 return ((tsf &~ 0x7fff) | rstamp);
3631 * Intercept management frames to collect beacon rssi data
3632 * and to do ibss merges.
3635 ath_recv_mgmt(struct ieee80211_node *ni, struct mbuf *m,
3636 int subtype, int rssi, int nf)
3638 struct ieee80211vap *vap = ni->ni_vap;
3639 struct ath_softc *sc = vap->iv_ic->ic_ifp->if_softc;
3642 * Call up first so subsequent work can use information
3643 * potentially stored in the node (e.g. for ibss merge).
3645 ATH_VAP(vap)->av_recv_mgmt(ni, m, subtype, rssi, nf);
3647 case IEEE80211_FC0_SUBTYPE_BEACON:
3648 /* update rssi statistics for use by the hal */
3649 ATH_RSSI_LPF(sc->sc_halstats.ns_avgbrssi, rssi);
3650 if (sc->sc_syncbeacon &&
3651 ni == vap->iv_bss && vap->iv_state == IEEE80211_S_RUN) {
3653 * Resync beacon timers using the tsf of the beacon
3654 * frame we just received.
3656 ath_beacon_config(sc, vap);
3659 case IEEE80211_FC0_SUBTYPE_PROBE_RESP:
3660 if (vap->iv_opmode == IEEE80211_M_IBSS &&
3661 vap->iv_state == IEEE80211_S_RUN) {
3662 uint32_t rstamp = sc->sc_lastrs->rs_tstamp;
3663 u_int64_t tsf = ath_extend_tsf(rstamp,
3664 ath_hal_gettsf64(sc->sc_ah));
3666 * Handle ibss merge as needed; check the tsf on the
3667 * frame before attempting the merge. The 802.11 spec
3668 * says the station should change it's bssid to match
3669 * the oldest station with the same ssid, where oldest
3670 * is determined by the tsf. Note that hardware
3671 * reconfiguration happens through callback to
3672 * ath_newstate as the state machine will go from
3673 * RUN -> RUN when this happens.
3675 if (le64toh(ni->ni_tstamp.tsf) >= tsf) {
3676 DPRINTF(sc, ATH_DEBUG_STATE,
3677 "ibss merge, rstamp %u tsf %ju "
3678 "tstamp %ju\n", rstamp, (uintmax_t)tsf,
3679 (uintmax_t)ni->ni_tstamp.tsf);
3680 (void) ieee80211_ibss_merge(ni);
3688 * Set the default antenna.
3691 ath_setdefantenna(struct ath_softc *sc, u_int antenna)
3693 struct ath_hal *ah = sc->sc_ah;
3695 /* XXX block beacon interrupts */
3696 ath_hal_setdefantenna(ah, antenna);
3697 if (sc->sc_defant != antenna)
3698 sc->sc_stats.ast_ant_defswitch++;
3699 sc->sc_defant = antenna;
3700 sc->sc_rxotherant = 0;
3704 ath_rx_tap(struct ifnet *ifp, struct mbuf *m,
3705 const struct ath_rx_status *rs, u_int64_t tsf, int16_t nf)
3707 #define CHAN_HT20 htole32(IEEE80211_CHAN_HT20)
3708 #define CHAN_HT40U htole32(IEEE80211_CHAN_HT40U)
3709 #define CHAN_HT40D htole32(IEEE80211_CHAN_HT40D)
3710 #define CHAN_HT (CHAN_HT20|CHAN_HT40U|CHAN_HT40D)
3711 struct ath_softc *sc = ifp->if_softc;
3712 const HAL_RATE_TABLE *rt;
3715 rt = sc->sc_currates;
3716 KASSERT(rt != NULL, ("no rate table, mode %u", sc->sc_curmode));
3717 rix = rt->rateCodeToIndex[rs->rs_rate];
3718 sc->sc_rx_th.wr_rate = sc->sc_hwmap[rix].ieeerate;
3719 sc->sc_rx_th.wr_flags = sc->sc_hwmap[rix].rxflags;
3720 #ifdef AH_SUPPORT_AR5416
3721 sc->sc_rx_th.wr_chan_flags &= ~CHAN_HT;
3722 if (sc->sc_rx_th.wr_rate & IEEE80211_RATE_MCS) { /* HT rate */
3723 struct ieee80211com *ic = ifp->if_l2com;
3725 if ((rs->rs_flags & HAL_RX_2040) == 0)
3726 sc->sc_rx_th.wr_chan_flags |= CHAN_HT20;
3727 else if (IEEE80211_IS_CHAN_HT40U(ic->ic_curchan))
3728 sc->sc_rx_th.wr_chan_flags |= CHAN_HT40U;
3730 sc->sc_rx_th.wr_chan_flags |= CHAN_HT40D;
3731 if ((rs->rs_flags & HAL_RX_GI) == 0)
3732 sc->sc_rx_th.wr_flags |= IEEE80211_RADIOTAP_F_SHORTGI;
3735 sc->sc_rx_th.wr_tsf = htole64(ath_extend_tsf(rs->rs_tstamp, tsf));
3736 if (rs->rs_status & HAL_RXERR_CRC)
3737 sc->sc_rx_th.wr_flags |= IEEE80211_RADIOTAP_F_BADFCS;
3738 /* XXX propagate other error flags from descriptor */
3739 sc->sc_rx_th.wr_antnoise = nf;
3740 sc->sc_rx_th.wr_antsignal = nf + rs->rs_rssi;
3741 sc->sc_rx_th.wr_antenna = rs->rs_antenna;
3749 ath_handle_micerror(struct ieee80211com *ic,
3750 struct ieee80211_frame *wh, int keyix)
3752 struct ieee80211_node *ni;
3754 /* XXX recheck MIC to deal w/ chips that lie */
3755 /* XXX discard MIC errors on !data frames */
3756 ni = ieee80211_find_rxnode(ic, (const struct ieee80211_frame_min *) wh);
3758 ieee80211_notify_michael_failure(ni->ni_vap, wh, keyix);
3759 ieee80211_free_node(ni);
3764 ath_rx_task(void *arg, int npending)
3766 #define PA2DESC(_sc, _pa) \
3767 ((struct ath_desc *)((caddr_t)(_sc)->sc_rxdma.dd_desc + \
3768 ((_pa) - (_sc)->sc_rxdma.dd_desc_paddr)))
3769 struct ath_softc *sc = arg;
3772 struct ieee80211com *ic;
3774 struct ath_desc *ds;
3775 struct ath_rx_status *rs;
3777 struct ieee80211_node *ni;
3778 int len, type, ngood;
3784 wlan_serialize_enter();
3789 DPRINTF(sc, ATH_DEBUG_RX_PROC, "%s: pending %u\n", __func__, npending);
3791 nf = ath_hal_getchannoise(ah, sc->sc_curchan);
3792 sc->sc_stats.ast_rx_noise = nf;
3793 tsf = ath_hal_gettsf64(ah);
3795 bf = STAILQ_FIRST(&sc->sc_rxbuf);
3796 if (bf == NULL) { /* NB: shouldn't happen */
3797 if_printf(ifp, "%s: no buffer!\n", __func__);
3801 if (m == NULL) { /* NB: shouldn't happen */
3803 * If mbuf allocation failed previously there
3804 * will be no mbuf; try again to re-populate it.
3806 /* XXX make debug msg */
3807 if_printf(ifp, "%s: no mbuf!\n", __func__);
3808 STAILQ_REMOVE_HEAD(&sc->sc_rxbuf, bf_list);
3812 if (ds->ds_link == bf->bf_daddr) {
3813 /* NB: never process the self-linked entry at the end */
3816 /* XXX sync descriptor memory */
3818 * Must provide the virtual address of the current
3819 * descriptor, the physical address, and the virtual
3820 * address of the next descriptor in the h/w chain.
3821 * This allows the HAL to look ahead to see if the
3822 * hardware is done with a descriptor by checking the
3823 * done bit in the following descriptor and the address
3824 * of the current descriptor the DMA engine is working
3825 * on. All this is necessary because of our use of
3826 * a self-linked list to avoid rx overruns.
3828 rs = &bf->bf_status.ds_rxstat;
3829 status = ath_hal_rxprocdesc(ah, ds,
3830 bf->bf_daddr, PA2DESC(sc, ds->ds_link), rs);
3832 if (sc->sc_debug & ATH_DEBUG_RECV_DESC)
3833 ath_printrxbuf(sc, bf, 0, status == HAL_OK);
3835 if (status == HAL_EINPROGRESS)
3837 STAILQ_REMOVE_HEAD(&sc->sc_rxbuf, bf_list);
3838 if (rs->rs_status != 0) {
3839 if (rs->rs_status & HAL_RXERR_CRC)
3840 sc->sc_stats.ast_rx_crcerr++;
3841 if (rs->rs_status & HAL_RXERR_FIFO)
3842 sc->sc_stats.ast_rx_fifoerr++;
3843 if (rs->rs_status & HAL_RXERR_PHY) {
3844 sc->sc_stats.ast_rx_phyerr++;
3845 phyerr = rs->rs_phyerr & 0x1f;
3846 sc->sc_stats.ast_rx_phy[phyerr]++;
3847 goto rx_error; /* NB: don't count in ierrors */
3849 if (rs->rs_status & HAL_RXERR_DECRYPT) {
3851 * Decrypt error. If the error occurred
3852 * because there was no hardware key, then
3853 * let the frame through so the upper layers
3854 * can process it. This is necessary for 5210
3855 * parts which have no way to setup a ``clear''
3858 * XXX do key cache faulting
3860 if (rs->rs_keyix == HAL_RXKEYIX_INVALID)
3862 sc->sc_stats.ast_rx_badcrypt++;
3864 if (rs->rs_status & HAL_RXERR_MIC) {
3865 sc->sc_stats.ast_rx_badmic++;
3867 * Do minimal work required to hand off
3868 * the 802.11 header for notification.
3870 /* XXX frag's and qos frames */
3871 len = rs->rs_datalen;
3872 if (len >= sizeof (struct ieee80211_frame)) {
3873 bus_dmamap_sync(sc->sc_dmat,
3875 BUS_DMASYNC_POSTREAD);
3876 ath_handle_micerror(ic,
3877 mtod(m, struct ieee80211_frame *),
3879 rs->rs_keyix-32 : rs->rs_keyix);
3885 * Cleanup any pending partial frame.
3887 if (sc->sc_rxpending != NULL) {
3888 m_freem(sc->sc_rxpending);
3889 sc->sc_rxpending = NULL;
3892 * When a tap is present pass error frames
3893 * that have been requested. By default we
3894 * pass decrypt+mic errors but others may be
3895 * interesting (e.g. crc).
3897 if (ieee80211_radiotap_active(ic) &&
3898 (rs->rs_status & sc->sc_monpass)) {
3899 bus_dmamap_sync(sc->sc_dmat, bf->bf_dmamap,
3900 BUS_DMASYNC_POSTREAD);
3901 /* NB: bpf needs the mbuf length setup */
3902 len = rs->rs_datalen;
3903 m->m_pkthdr.len = m->m_len = len;
3904 ath_rx_tap(ifp, m, rs, tsf, nf);
3905 ieee80211_radiotap_rx_all(ic, m);
3907 /* XXX pass MIC errors up for s/w reclaculation */
3912 * Sync and unmap the frame. At this point we're
3913 * committed to passing the mbuf somewhere so clear
3914 * bf_m; this means a new mbuf must be allocated
3915 * when the rx descriptor is setup again to receive
3918 bus_dmamap_sync(sc->sc_dmat, bf->bf_dmamap,
3919 BUS_DMASYNC_POSTREAD);
3920 bus_dmamap_unload(sc->sc_dmat, bf->bf_dmamap);
3923 len = rs->rs_datalen;
3928 * Frame spans multiple descriptors; save
3929 * it for the next completed descriptor, it
3930 * will be used to construct a jumbogram.
3932 if (sc->sc_rxpending != NULL) {
3933 /* NB: max frame size is currently 2 clusters */
3934 sc->sc_stats.ast_rx_toobig++;
3935 m_freem(sc->sc_rxpending);
3937 m->m_pkthdr.rcvif = ifp;
3938 m->m_pkthdr.len = len;
3939 sc->sc_rxpending = m;
3941 } else if (sc->sc_rxpending != NULL) {
3943 * This is the second part of a jumbogram,
3944 * chain it to the first mbuf, adjust the
3945 * frame length, and clear the rxpending state.
3947 sc->sc_rxpending->m_next = m;
3948 sc->sc_rxpending->m_pkthdr.len += len;
3949 m = sc->sc_rxpending;
3950 sc->sc_rxpending = NULL;
3953 * Normal single-descriptor receive; setup
3954 * the rcvif and packet length.
3956 m->m_pkthdr.rcvif = ifp;
3957 m->m_pkthdr.len = len;
3961 sc->sc_stats.ast_ant_rx[rs->rs_antenna]++;
3964 * Populate the rx status block. When there are bpf
3965 * listeners we do the additional work to provide
3966 * complete status. Otherwise we fill in only the
3967 * material required by ieee80211_input. Note that
3968 * noise setting is filled in above.
3970 if (ieee80211_radiotap_active(ic))
3971 ath_rx_tap(ifp, m, rs, tsf, nf);
3974 * From this point on we assume the frame is at least
3975 * as large as ieee80211_frame_min; verify that.
3977 if (len < IEEE80211_MIN_LEN) {
3978 if (!ieee80211_radiotap_active(ic)) {
3979 DPRINTF(sc, ATH_DEBUG_RECV,
3980 "%s: short packet %d\n", __func__, len);
3981 sc->sc_stats.ast_rx_tooshort++;
3983 /* NB: in particular this captures ack's */
3984 ieee80211_radiotap_rx_all(ic, m);
3990 if (IFF_DUMPPKTS(sc, ATH_DEBUG_RECV)) {
3991 const HAL_RATE_TABLE *rt = sc->sc_currates;
3992 uint8_t rix = rt->rateCodeToIndex[rs->rs_rate];
3994 ieee80211_dump_pkt(ic, mtod(m, caddr_t), len,
3995 sc->sc_hwmap[rix].ieeerate, rs->rs_rssi);
3998 m_adj(m, -IEEE80211_CRC_LEN);
4001 * Locate the node for sender, track state, and then
4002 * pass the (referenced) node up to the 802.11 layer
4005 ni = ieee80211_find_rxnode_withkey(ic,
4006 mtod(m, const struct ieee80211_frame_min *),
4007 rs->rs_keyix == HAL_RXKEYIX_INVALID ?
4008 IEEE80211_KEYIX_NONE : rs->rs_keyix);
4011 * Sending station is known, dispatch directly.
4014 type = ieee80211_input(ni, m, rs->rs_rssi, nf);
4015 ieee80211_free_node(ni);
4017 * Arrange to update the last rx timestamp only for
4018 * frames from our ap when operating in station mode.
4019 * This assumes the rx key is always setup when
4022 if (ic->ic_opmode == IEEE80211_M_STA &&
4023 rs->rs_keyix != HAL_RXKEYIX_INVALID)
4026 type = ieee80211_input_all(ic, m, rs->rs_rssi, nf);
4029 * Track rx rssi and do any rx antenna management.
4031 ATH_RSSI_LPF(sc->sc_halstats.ns_avgrssi, rs->rs_rssi);
4032 if (sc->sc_diversity) {
4034 * When using fast diversity, change the default rx
4035 * antenna if diversity chooses the other antenna 3
4038 if (sc->sc_defant != rs->rs_antenna) {
4039 if (++sc->sc_rxotherant >= 3)
4040 ath_setdefantenna(sc, rs->rs_antenna);
4042 sc->sc_rxotherant = 0;
4044 if (sc->sc_softled) {
4046 * Blink for any data frame. Otherwise do a
4047 * heartbeat-style blink when idle. The latter
4048 * is mainly for station mode where we depend on
4049 * periodic beacon frames to trigger the poll event.
4051 if (type == IEEE80211_FC0_TYPE_DATA) {
4052 const HAL_RATE_TABLE *rt = sc->sc_currates;
4054 rt->rateCodeToIndex[rs->rs_rate]);
4055 } else if (ticks - sc->sc_ledevent >= sc->sc_ledidle)
4056 ath_led_event(sc, 0);
4059 STAILQ_INSERT_TAIL(&sc->sc_rxbuf, bf, bf_list);
4060 } while (ath_rxbuf_init(sc, bf) == 0);
4062 /* rx signal state monitoring */
4063 ath_hal_rxmonitor(ah, &sc->sc_halstats, sc->sc_curchan);
4065 sc->sc_lastrx = tsf;
4067 if ((ifp->if_flags & IFF_OACTIVE) == 0) {
4068 #ifdef IEEE80211_SUPPORT_SUPERG
4069 ieee80211_ff_age_all(ic, 100);
4071 if (!ifq_is_empty(&ifp->if_snd))
4074 wlan_serialize_exit();
4079 ath_txq_init(struct ath_softc *sc, struct ath_txq *txq, int qnum)
4081 txq->axq_qnum = qnum;
4084 txq->axq_intrcnt = 0;
4085 txq->axq_link = NULL;
4086 STAILQ_INIT(&txq->axq_q);
4090 * Setup a h/w transmit queue.
4092 static struct ath_txq *
4093 ath_txq_setup(struct ath_softc *sc, int qtype, int subtype)
4095 struct ath_hal *ah = sc->sc_ah;
4099 memset(&qi, 0, sizeof(qi));
4100 qi.tqi_subtype = subtype;
4101 qi.tqi_aifs = HAL_TXQ_USEDEFAULT;
4102 qi.tqi_cwmin = HAL_TXQ_USEDEFAULT;
4103 qi.tqi_cwmax = HAL_TXQ_USEDEFAULT;
4105 * Enable interrupts only for EOL and DESC conditions.
4106 * We mark tx descriptors to receive a DESC interrupt
4107 * when a tx queue gets deep; otherwise waiting for the
4108 * EOL to reap descriptors. Note that this is done to
4109 * reduce interrupt load and this only defers reaping
4110 * descriptors, never transmitting frames. Aside from
4111 * reducing interrupts this also permits more concurrency.
4112 * The only potential downside is if the tx queue backs
4113 * up in which case the top half of the kernel may backup
4114 * due to a lack of tx descriptors.
4116 qi.tqi_qflags = HAL_TXQ_TXEOLINT_ENABLE | HAL_TXQ_TXDESCINT_ENABLE;
4117 qnum = ath_hal_setuptxqueue(ah, qtype, &qi);
4120 * NB: don't print a message, this happens
4121 * normally on parts with too few tx queues
4125 if (qnum >= NELEM(sc->sc_txq)) {
4126 device_printf(sc->sc_dev,
4127 "hal qnum %u out of range, max %zu!\n",
4128 qnum, NELEM(sc->sc_txq));
4129 ath_hal_releasetxqueue(ah, qnum);
4132 if (!ATH_TXQ_SETUP(sc, qnum)) {
4133 ath_txq_init(sc, &sc->sc_txq[qnum], qnum);
4134 sc->sc_txqsetup |= 1<<qnum;
4136 return &sc->sc_txq[qnum];
4140 * Setup a hardware data transmit queue for the specified
4141 * access control. The hal may not support all requested
4142 * queues in which case it will return a reference to a
4143 * previously setup queue. We record the mapping from ac's
4144 * to h/w queues for use by ath_tx_start and also track
4145 * the set of h/w queues being used to optimize work in the
4146 * transmit interrupt handler and related routines.
4149 ath_tx_setup(struct ath_softc *sc, int ac, int haltype)
4151 struct ath_txq *txq;
4153 if (ac >= NELEM(sc->sc_ac2q)) {
4154 device_printf(sc->sc_dev, "AC %u out of range, max %zu!\n",
4155 ac, NELEM(sc->sc_ac2q));
4158 txq = ath_txq_setup(sc, HAL_TX_QUEUE_DATA, haltype);
4161 sc->sc_ac2q[ac] = txq;
4168 * Update WME parameters for a transmit queue.
4171 ath_txq_update(struct ath_softc *sc, int ac)
4173 #define ATH_EXPONENT_TO_VALUE(v) ((1<<v)-1)
4174 #define ATH_TXOP_TO_US(v) (v<<5)
4175 struct ifnet *ifp = sc->sc_ifp;
4176 struct ieee80211com *ic = ifp->if_l2com;
4177 struct ath_txq *txq = sc->sc_ac2q[ac];
4178 struct wmeParams *wmep = &ic->ic_wme.wme_chanParams.cap_wmeParams[ac];
4179 struct ath_hal *ah = sc->sc_ah;
4182 ath_hal_gettxqueueprops(ah, txq->axq_qnum, &qi);
4183 #ifdef IEEE80211_SUPPORT_TDMA
4186 * AIFS is zero so there's no pre-transmit wait. The
4187 * burst time defines the slot duration and is configured
4188 * through net80211. The QCU is setup to not do post-xmit
4189 * back off, lockout all lower-priority QCU's, and fire
4190 * off the DMA beacon alert timer which is setup based
4191 * on the slot configuration.
4193 qi.tqi_qflags = HAL_TXQ_TXOKINT_ENABLE
4194 | HAL_TXQ_TXERRINT_ENABLE
4195 | HAL_TXQ_TXURNINT_ENABLE
4196 | HAL_TXQ_TXEOLINT_ENABLE
4198 | HAL_TXQ_BACKOFF_DISABLE
4199 | HAL_TXQ_ARB_LOCKOUT_GLOBAL
4203 qi.tqi_readyTime = sc->sc_tdmaslotlen;
4204 qi.tqi_burstTime = qi.tqi_readyTime;
4207 qi.tqi_qflags = HAL_TXQ_TXOKINT_ENABLE
4208 | HAL_TXQ_TXERRINT_ENABLE
4209 | HAL_TXQ_TXDESCINT_ENABLE
4210 | HAL_TXQ_TXURNINT_ENABLE
4212 qi.tqi_aifs = wmep->wmep_aifsn;
4213 qi.tqi_cwmin = ATH_EXPONENT_TO_VALUE(wmep->wmep_logcwmin);
4214 qi.tqi_cwmax = ATH_EXPONENT_TO_VALUE(wmep->wmep_logcwmax);
4215 qi.tqi_readyTime = 0;
4216 qi.tqi_burstTime = ATH_TXOP_TO_US(wmep->wmep_txopLimit);
4217 #ifdef IEEE80211_SUPPORT_TDMA
4221 DPRINTF(sc, ATH_DEBUG_RESET,
4222 "%s: Q%u qflags 0x%x aifs %u cwmin %u cwmax %u burstTime %u\n",
4223 __func__, txq->axq_qnum, qi.tqi_qflags,
4224 qi.tqi_aifs, qi.tqi_cwmin, qi.tqi_cwmax, qi.tqi_burstTime);
4226 if (!ath_hal_settxqueueprops(ah, txq->axq_qnum, &qi)) {
4227 if_printf(ifp, "unable to update hardware queue "
4228 "parameters for %s traffic!\n",
4229 ieee80211_wme_acnames[ac]);
4232 ath_hal_resettxqueue(ah, txq->axq_qnum); /* push to h/w */
4235 #undef ATH_TXOP_TO_US
4236 #undef ATH_EXPONENT_TO_VALUE
4240 * Callback from the 802.11 layer to update WME parameters.
4243 ath_wme_update(struct ieee80211com *ic)
4245 struct ath_softc *sc = ic->ic_ifp->if_softc;
4247 return !ath_txq_update(sc, WME_AC_BE) ||
4248 !ath_txq_update(sc, WME_AC_BK) ||
4249 !ath_txq_update(sc, WME_AC_VI) ||
4250 !ath_txq_update(sc, WME_AC_VO) ? EIO : 0;
4254 * Reclaim resources for a setup queue.
4257 ath_tx_cleanupq(struct ath_softc *sc, struct ath_txq *txq)
4260 ath_hal_releasetxqueue(sc->sc_ah, txq->axq_qnum);
4261 sc->sc_txqsetup &= ~(1<<txq->axq_qnum);
4265 * Reclaim all tx queue resources.
4268 ath_tx_cleanup(struct ath_softc *sc)
4272 for (i = 0; i < HAL_NUM_TX_QUEUES; i++)
4273 if (ATH_TXQ_SETUP(sc, i))
4274 ath_tx_cleanupq(sc, &sc->sc_txq[i]);
4278 * Return h/w rate index for an IEEE rate (w/o basic rate bit)
4279 * using the current rates in sc_rixmap.
4282 ath_tx_findrix(const struct ath_softc *sc, uint8_t rate)
4284 int rix = sc->sc_rixmap[rate];
4285 /* NB: return lowest rix for invalid rate */
4286 return (rix == 0xff ? 0 : rix);
4290 * Reclaim mbuf resources. For fragmented frames we
4291 * need to claim each frag chained with m_nextpkt.
4294 ath_freetx(struct mbuf *m)
4299 next = m->m_nextpkt;
4300 m->m_nextpkt = NULL;
4302 } while ((m = next) != NULL);
4306 ath_tx_dmasetup(struct ath_softc *sc, struct ath_buf *bf, struct mbuf *m0)
4312 * Load the DMA map so any coalescing is done. This
4313 * also calculates the number of descriptors we need.
4315 error = bus_dmamap_load_mbuf_defrag(sc->sc_dmat, bf->bf_dmamap, &m0,
4316 bf->bf_segs, ATH_TXDESC,
4317 &bf->bf_nseg, BUS_DMA_NOWAIT);
4319 sc->sc_stats.ast_tx_busdma++;
4325 * Discard null packets.
4327 if (bf->bf_nseg == 0) { /* null packet, discard */
4328 sc->sc_stats.ast_tx_nodata++;
4332 DPRINTF(sc, ATH_DEBUG_XMIT, "%s: m %p len %u\n",
4333 __func__, m0, m0->m_pkthdr.len);
4334 bus_dmamap_sync(sc->sc_dmat, bf->bf_dmamap, BUS_DMASYNC_PREWRITE);
4341 ath_tx_handoff(struct ath_softc *sc, struct ath_txq *txq, struct ath_buf *bf)
4343 struct ath_hal *ah = sc->sc_ah;
4344 struct ath_desc *ds, *ds0;
4348 * Fillin the remainder of the descriptor info.
4350 ds0 = ds = bf->bf_desc;
4351 for (i = 0; i < bf->bf_nseg; i++, ds++) {
4352 ds->ds_data = bf->bf_segs[i].ds_addr;
4353 if (i == bf->bf_nseg - 1)
4356 ds->ds_link = bf->bf_daddr + sizeof(*ds) * (i + 1);
4357 ath_hal_filltxdesc(ah, ds
4358 , bf->bf_segs[i].ds_len /* segment length */
4359 , i == 0 /* first segment */
4360 , i == bf->bf_nseg - 1 /* last segment */
4361 , ds0 /* first descriptor */
4363 DPRINTF(sc, ATH_DEBUG_XMIT,
4364 "%s: %d: %08x %08x %08x %08x %08x %08x\n",
4365 __func__, i, ds->ds_link, ds->ds_data,
4366 ds->ds_ctl0, ds->ds_ctl1, ds->ds_hw[0], ds->ds_hw[1]);
4369 * Insert the frame on the outbound list and pass it on
4370 * to the hardware. Multicast frames buffered for power
4371 * save stations and transmit from the CAB queue are stored
4372 * on a s/w only queue and loaded on to the CAB queue in
4373 * the SWBA handler since frames only go out on DTIM and
4374 * to avoid possible races.
4376 KASSERT((bf->bf_flags & ATH_BUF_BUSY) == 0,
4377 ("busy status 0x%x", bf->bf_flags));
4378 if (txq->axq_qnum != ATH_TXQ_SWQ) {
4379 #ifdef IEEE80211_SUPPORT_TDMA
4381 * Supporting transmit dma. If the queue is busy it is
4382 * impossible to determine if we've won the race against
4383 * the chipset checking the link field or not, so we don't
4384 * try. Instead we let the TX interrupt detect the case
4385 * and restart the transmitter.
4387 * If the queue is not busy we can start things rolling
4392 ATH_TXQ_INSERT_TAIL(txq, bf, bf_list);
4393 qbusy = ath_hal_txqenabled(ah, txq->axq_qnum);
4396 if (txq->axq_link != NULL) {
4398 * We had already started one previously but
4399 * not yet processed the TX interrupt. Don't
4400 * try to race a restart because we do not
4401 * know where it stopped, let the TX interrupt
4402 * restart us when it figures out where we
4406 *txq->axq_link = bf->bf_daddr;
4407 txq->axq_flags |= ATH_TXQ_PUTPENDING;
4410 * We are first in line, we can safely start
4414 ath_hal_puttxbuf(ah, txq->axq_qnum,
4419 * The queue is busy, go ahead and link us in but
4420 * do not try to start/restart the tx. We just
4421 * don't know whether it will pick up our link
4422 * or not and we don't want to double-xmit.
4424 if (txq->axq_link != NULL) {
4426 *txq->axq_link = bf->bf_daddr;
4428 txq->axq_flags |= ATH_TXQ_PUTPENDING;
4431 ath_hal_puttxbuf(ah, txq->axq_qnum,
4432 STAILQ_FIRST(&txq->axq_q)->bf_daddr);
4435 ATH_TXQ_INSERT_TAIL(txq, bf, bf_list);
4436 if (txq->axq_link == NULL) {
4437 ath_hal_puttxbuf(ah, txq->axq_qnum, bf->bf_daddr);
4438 DPRINTF(sc, ATH_DEBUG_XMIT,
4439 "%s: TXDP[%u] = %p (%p) depth %d\n",
4440 __func__, txq->axq_qnum,
4441 (caddr_t)bf->bf_daddr, bf->bf_desc,
4444 *txq->axq_link = bf->bf_daddr;
4445 DPRINTF(sc, ATH_DEBUG_XMIT,
4446 "%s: link[%u](%p)=%p (%p) depth %d\n", __func__,
4447 txq->axq_qnum, txq->axq_link,
4448 (caddr_t)bf->bf_daddr, bf->bf_desc, txq->axq_depth);
4450 #endif /* IEEE80211_SUPPORT_TDMA */
4451 txq->axq_link = &bf->bf_desc[bf->bf_nseg - 1].ds_link;
4452 ath_hal_txstart(ah, txq->axq_qnum);
4454 if (txq->axq_link != NULL) {
4455 struct ath_buf *last = ATH_TXQ_LAST(txq);
4456 struct ieee80211_frame *wh;
4458 /* mark previous frame */
4459 wh = mtod(last->bf_m, struct ieee80211_frame *);
4460 wh->i_fc[1] |= IEEE80211_FC1_MORE_DATA;
4461 bus_dmamap_sync(sc->sc_dmat, last->bf_dmamap,
4462 BUS_DMASYNC_PREWRITE);
4464 /* link descriptor */
4465 *txq->axq_link = bf->bf_daddr;
4467 ATH_TXQ_INSERT_TAIL(txq, bf, bf_list);
4468 txq->axq_link = &bf->bf_desc[bf->bf_nseg - 1].ds_link;
4473 ath_tx_start(struct ath_softc *sc, struct ieee80211_node *ni, struct ath_buf *bf,
4476 struct ieee80211vap *vap = ni->ni_vap;
4477 struct ath_vap *avp = ATH_VAP(vap);
4478 struct ath_hal *ah = sc->sc_ah;
4479 struct ifnet *ifp = sc->sc_ifp;
4480 struct ieee80211com *ic = ifp->if_l2com;
4481 const struct chanAccParams *cap = &ic->ic_wme.wme_chanParams;
4482 int error, iswep, ismcast, isfrag, ismrr;
4483 int keyix, hdrlen, pktlen, try0;
4484 u_int8_t rix, txrate, ctsrate;
4485 u_int8_t cix = 0xff; /* NB: silence compiler */
4486 struct ath_desc *ds;
4487 struct ath_txq *txq;
4488 struct ieee80211_frame *wh;
4489 u_int subtype, flags, ctsduration;
4491 const HAL_RATE_TABLE *rt;
4492 HAL_BOOL shortPreamble;
4493 struct ath_node *an;
4496 wh = mtod(m0, struct ieee80211_frame *);
4497 iswep = wh->i_fc[1] & IEEE80211_FC1_WEP;
4498 ismcast = IEEE80211_IS_MULTICAST(wh->i_addr1);
4499 isfrag = m0->m_flags & M_FRAG;
4500 hdrlen = ieee80211_anyhdrsize(wh);
4502 * Packet length must not include any
4503 * pad bytes; deduct them here.
4505 pktlen = m0->m_pkthdr.len - (hdrlen & 3);
4508 const struct ieee80211_cipher *cip;
4509 struct ieee80211_key *k;
4512 * Construct the 802.11 header+trailer for an encrypted
4513 * frame. The only reason this can fail is because of an
4514 * unknown or unsupported cipher/key type.
4516 k = ieee80211_crypto_encap(ni, m0);
4519 * This can happen when the key is yanked after the
4520 * frame was queued. Just discard the frame; the
4521 * 802.11 layer counts failures and provides
4522 * debugging/diagnostics.
4528 * Adjust the packet + header lengths for the crypto
4529 * additions and calculate the h/w key index. When
4530 * a s/w mic is done the frame will have had any mic
4531 * added to it prior to entry so m0->m_pkthdr.len will
4532 * account for it. Otherwise we need to add it to the
4536 hdrlen += cip->ic_header;
4537 pktlen += cip->ic_header + cip->ic_trailer;
4538 /* NB: frags always have any TKIP MIC done in s/w */
4539 if ((k->wk_flags & IEEE80211_KEY_SWMIC) == 0 && !isfrag)
4540 pktlen += cip->ic_miclen;
4541 keyix = k->wk_keyix;
4543 /* packet header may have moved, reset our local pointer */
4544 wh = mtod(m0, struct ieee80211_frame *);
4545 } else if (ni->ni_ucastkey.wk_cipher == &ieee80211_cipher_none) {
4547 * Use station key cache slot, if assigned.
4549 keyix = ni->ni_ucastkey.wk_keyix;
4550 if (keyix == IEEE80211_KEYIX_NONE)
4551 keyix = HAL_TXKEYIX_INVALID;
4553 keyix = HAL_TXKEYIX_INVALID;
4555 pktlen += IEEE80211_CRC_LEN;
4558 * Load the DMA map so any coalescing is done. This
4559 * also calculates the number of descriptors we need.
4561 error = ath_tx_dmasetup(sc, bf, m0);
4565 bf->bf_node = ni; /* NB: held reference */
4566 m0 = bf->bf_m; /* NB: may have changed */
4567 wh = mtod(m0, struct ieee80211_frame *);
4569 /* setup descriptors */
4571 rt = sc->sc_currates;
4572 KASSERT(rt != NULL, ("no rate table, mode %u", sc->sc_curmode));
4575 * NB: the 802.11 layer marks whether or not we should
4576 * use short preamble based on the current mode and
4577 * negotiated parameters.
4579 if ((ic->ic_flags & IEEE80211_F_SHPREAMBLE) &&
4580 (ni->ni_capinfo & IEEE80211_CAPINFO_SHORT_PREAMBLE)) {
4581 shortPreamble = AH_TRUE;
4582 sc->sc_stats.ast_tx_shortpre++;
4584 shortPreamble = AH_FALSE;
4588 flags = HAL_TXDESC_CLRDMASK; /* XXX needed for crypto errs */
4589 ismrr = 0; /* default no multi-rate retry*/
4590 pri = M_WME_GETAC(m0); /* honor classification */
4591 /* XXX use txparams instead of fixed values */
4593 * Calculate Atheros packet type from IEEE80211 packet header,
4594 * setup for rate calculations, and select h/w transmit queue.
4596 switch (wh->i_fc[0] & IEEE80211_FC0_TYPE_MASK) {
4597 case IEEE80211_FC0_TYPE_MGT:
4598 subtype = wh->i_fc[0] & IEEE80211_FC0_SUBTYPE_MASK;
4599 if (subtype == IEEE80211_FC0_SUBTYPE_BEACON)
4600 atype = HAL_PKT_TYPE_BEACON;
4601 else if (subtype == IEEE80211_FC0_SUBTYPE_PROBE_RESP)
4602 atype = HAL_PKT_TYPE_PROBE_RESP;
4603 else if (subtype == IEEE80211_FC0_SUBTYPE_ATIM)
4604 atype = HAL_PKT_TYPE_ATIM;
4606 atype = HAL_PKT_TYPE_NORMAL; /* XXX */
4607 rix = an->an_mgmtrix;
4608 txrate = rt->info[rix].rateCode;
4610 txrate |= rt->info[rix].shortPreamble;
4611 try0 = ATH_TXMGTTRY;
4612 flags |= HAL_TXDESC_INTREQ; /* force interrupt */
4614 case IEEE80211_FC0_TYPE_CTL:
4615 atype = HAL_PKT_TYPE_PSPOLL; /* stop setting of duration */
4616 rix = an->an_mgmtrix;
4617 txrate = rt->info[rix].rateCode;
4619 txrate |= rt->info[rix].shortPreamble;
4620 try0 = ATH_TXMGTTRY;
4621 flags |= HAL_TXDESC_INTREQ; /* force interrupt */
4623 case IEEE80211_FC0_TYPE_DATA:
4624 atype = HAL_PKT_TYPE_NORMAL; /* default */
4626 * Data frames: multicast frames go out at a fixed rate,
4627 * EAPOL frames use the mgmt frame rate; otherwise consult
4628 * the rate control module for the rate to use.
4631 rix = an->an_mcastrix;
4632 txrate = rt->info[rix].rateCode;
4634 txrate |= rt->info[rix].shortPreamble;
4636 } else if (m0->m_flags & M_EAPOL) {
4637 /* XXX? maybe always use long preamble? */
4638 rix = an->an_mgmtrix;
4639 txrate = rt->info[rix].rateCode;
4641 txrate |= rt->info[rix].shortPreamble;
4642 try0 = ATH_TXMAXTRY; /* XXX?too many? */
4644 ath_rate_findrate(sc, an, shortPreamble, pktlen,
4645 &rix, &try0, &txrate);
4646 sc->sc_txrix = rix; /* for LED blinking */
4647 sc->sc_lastdatarix = rix; /* for fast frames */
4648 if (try0 != ATH_TXMAXTRY)
4651 if (cap->cap_wmeParams[pri].wmep_noackPolicy)
4652 flags |= HAL_TXDESC_NOACK;
4655 if_printf(ifp, "bogus frame type 0x%x (%s)\n",
4656 wh->i_fc[0] & IEEE80211_FC0_TYPE_MASK, __func__);
4661 txq = sc->sc_ac2q[pri];
4664 * When servicing one or more stations in power-save mode
4665 * (or) if there is some mcast data waiting on the mcast
4666 * queue (to prevent out of order delivery) multicast
4667 * frames must be buffered until after the beacon.
4669 if (ismcast && (vap->iv_ps_sta || avp->av_mcastq.axq_depth))
4670 txq = &avp->av_mcastq;
4673 * Calculate miscellaneous flags.
4676 flags |= HAL_TXDESC_NOACK; /* no ack on broad/multicast */
4677 } else if (pktlen > vap->iv_rtsthreshold &&
4678 (ni->ni_ath_flags & IEEE80211_NODE_FF) == 0) {
4679 flags |= HAL_TXDESC_RTSENA; /* RTS based on frame length */
4680 cix = rt->info[rix].controlRate;
4681 sc->sc_stats.ast_tx_rts++;
4683 if (flags & HAL_TXDESC_NOACK) /* NB: avoid double counting */
4684 sc->sc_stats.ast_tx_noack++;
4685 #ifdef IEEE80211_SUPPORT_TDMA
4686 if (sc->sc_tdma && (flags & HAL_TXDESC_NOACK) == 0) {
4687 DPRINTF(sc, ATH_DEBUG_TDMA,
4688 "%s: discard frame, ACK required w/ TDMA\n", __func__);
4689 sc->sc_stats.ast_tdma_ack++;
4696 * If 802.11g protection is enabled, determine whether
4697 * to use RTS/CTS or just CTS. Note that this is only
4698 * done for OFDM unicast frames.
4700 if ((ic->ic_flags & IEEE80211_F_USEPROT) &&
4701 rt->info[rix].phy == IEEE80211_T_OFDM &&
4702 (flags & HAL_TXDESC_NOACK) == 0) {
4703 /* XXX fragments must use CCK rates w/ protection */
4704 if (ic->ic_protmode == IEEE80211_PROT_RTSCTS)
4705 flags |= HAL_TXDESC_RTSENA;
4706 else if (ic->ic_protmode == IEEE80211_PROT_CTSONLY)
4707 flags |= HAL_TXDESC_CTSENA;
4710 * For frags it would be desirable to use the
4711 * highest CCK rate for RTS/CTS. But stations
4712 * farther away may detect it at a lower CCK rate
4713 * so use the configured protection rate instead
4716 cix = rt->info[sc->sc_protrix].controlRate;
4718 cix = rt->info[sc->sc_protrix].controlRate;
4719 sc->sc_stats.ast_tx_protect++;
4723 * Calculate duration. This logically belongs in the 802.11
4724 * layer but it lacks sufficient information to calculate it.
4726 if ((flags & HAL_TXDESC_NOACK) == 0 &&
4727 (wh->i_fc[0] & IEEE80211_FC0_TYPE_MASK) != IEEE80211_FC0_TYPE_CTL) {
4730 dur = rt->info[rix].spAckDuration;
4732 dur = rt->info[rix].lpAckDuration;
4733 if (wh->i_fc[1] & IEEE80211_FC1_MORE_FRAG) {
4734 dur += dur; /* additional SIFS+ACK */
4735 KASSERT(m0->m_nextpkt != NULL, ("no fragment"));
4737 * Include the size of next fragment so NAV is
4738 * updated properly. The last fragment uses only
4741 dur += ath_hal_computetxtime(ah, rt,
4742 m0->m_nextpkt->m_pkthdr.len,
4743 rix, shortPreamble);
4747 * Force hardware to use computed duration for next
4748 * fragment by disabling multi-rate retry which updates
4749 * duration based on the multi-rate duration table.
4752 try0 = ATH_TXMGTTRY; /* XXX? */
4754 *(u_int16_t *)wh->i_dur = htole16(dur);
4758 * Calculate RTS/CTS rate and duration if needed.
4761 if (flags & (HAL_TXDESC_RTSENA|HAL_TXDESC_CTSENA)) {
4763 * CTS transmit rate is derived from the transmit rate
4764 * by looking in the h/w rate table. We must also factor
4765 * in whether or not a short preamble is to be used.
4767 /* NB: cix is set above where RTS/CTS is enabled */
4768 KASSERT(cix != 0xff, ("cix not setup"));
4769 ctsrate = rt->info[cix].rateCode;
4771 * Compute the transmit duration based on the frame
4772 * size and the size of an ACK frame. We call into the
4773 * HAL to do the computation since it depends on the
4774 * characteristics of the actual PHY being used.
4776 * NB: CTS is assumed the same size as an ACK so we can
4777 * use the precalculated ACK durations.
4779 if (shortPreamble) {
4780 ctsrate |= rt->info[cix].shortPreamble;
4781 if (flags & HAL_TXDESC_RTSENA) /* SIFS + CTS */
4782 ctsduration += rt->info[cix].spAckDuration;
4783 ctsduration += ath_hal_computetxtime(ah,
4784 rt, pktlen, rix, AH_TRUE);
4785 if ((flags & HAL_TXDESC_NOACK) == 0) /* SIFS + ACK */
4786 ctsduration += rt->info[rix].spAckDuration;
4788 if (flags & HAL_TXDESC_RTSENA) /* SIFS + CTS */
4789 ctsduration += rt->info[cix].lpAckDuration;
4790 ctsduration += ath_hal_computetxtime(ah,
4791 rt, pktlen, rix, AH_FALSE);
4792 if ((flags & HAL_TXDESC_NOACK) == 0) /* SIFS + ACK */
4793 ctsduration += rt->info[rix].lpAckDuration;
4796 * Must disable multi-rate retry when using RTS/CTS.
4799 try0 = ATH_TXMGTTRY; /* XXX */
4804 * At this point we are committed to sending the frame
4805 * and we don't need to look at m_nextpkt; clear it in
4806 * case this frame is part of frag chain.
4808 m0->m_nextpkt = NULL;
4810 if (IFF_DUMPPKTS(sc, ATH_DEBUG_XMIT))
4811 ieee80211_dump_pkt(ic, mtod(m0, const uint8_t *), m0->m_len,
4812 sc->sc_hwmap[rix].ieeerate, -1);
4814 if (ieee80211_radiotap_active_vap(vap)) {
4815 u_int64_t tsf = ath_hal_gettsf64(ah);
4817 sc->sc_tx_th.wt_tsf = htole64(tsf);
4818 sc->sc_tx_th.wt_flags = sc->sc_hwmap[rix].txflags;
4820 sc->sc_tx_th.wt_flags |= IEEE80211_RADIOTAP_F_WEP;
4822 sc->sc_tx_th.wt_flags |= IEEE80211_RADIOTAP_F_FRAG;
4823 sc->sc_tx_th.wt_rate = sc->sc_hwmap[rix].ieeerate;
4824 sc->sc_tx_th.wt_txpower = ni->ni_txpower;
4825 sc->sc_tx_th.wt_antenna = sc->sc_txantenna;
4827 ieee80211_radiotap_tx(vap, m0);
4831 * Determine if a tx interrupt should be generated for
4832 * this descriptor. We take a tx interrupt to reap
4833 * descriptors when the h/w hits an EOL condition or
4834 * when the descriptor is specifically marked to generate
4835 * an interrupt. We periodically mark descriptors in this
4836 * way to insure timely replenishing of the supply needed
4837 * for sending frames. Defering interrupts reduces system
4838 * load and potentially allows more concurrent work to be
4839 * done but if done to aggressively can cause senders to
4842 * NB: use >= to deal with sc_txintrperiod changing
4843 * dynamically through sysctl.
4845 if (flags & HAL_TXDESC_INTREQ) {
4846 txq->axq_intrcnt = 0;
4847 } else if (++txq->axq_intrcnt >= sc->sc_txintrperiod) {
4848 flags |= HAL_TXDESC_INTREQ;
4849 txq->axq_intrcnt = 0;
4853 * Formulate first tx descriptor with tx controls.
4855 /* XXX check return value? */
4856 ath_hal_setuptxdesc(ah, ds
4857 , pktlen /* packet length */
4858 , hdrlen /* header length */
4859 , atype /* Atheros packet type */
4860 , ni->ni_txpower /* txpower */
4861 , txrate, try0 /* series 0 rate/tries */
4862 , keyix /* key cache index */
4863 , sc->sc_txantenna /* antenna mode */
4865 , ctsrate /* rts/cts rate */
4866 , ctsduration /* rts/cts duration */
4868 bf->bf_txflags = flags;
4870 * Setup the multi-rate retry state only when we're
4871 * going to use it. This assumes ath_hal_setuptxdesc
4872 * initializes the descriptors (so we don't have to)
4873 * when the hardware supports multi-rate retry and
4877 ath_rate_setupxtxdesc(sc, an, ds, shortPreamble, rix);
4879 ath_tx_handoff(sc, txq, bf);
4884 * Process completed xmit descriptors from the specified queue.
4887 ath_tx_processq(struct ath_softc *sc, struct ath_txq *txq)
4889 struct ath_hal *ah = sc->sc_ah;
4890 struct ifnet *ifp = sc->sc_ifp;
4891 struct ieee80211com *ic = ifp->if_l2com;
4892 struct ath_buf *bf, *last;
4893 struct ath_desc *ds, *ds0;
4894 struct ath_tx_status *ts;
4895 struct ieee80211_node *ni;
4896 struct ath_node *an;
4897 int sr, lr, pri, nacked;
4900 DPRINTF(sc, ATH_DEBUG_TX_PROC, "%s: tx queue %u head %p link %p\n",
4901 __func__, txq->axq_qnum,
4902 (caddr_t)(uintptr_t) ath_hal_gettxbuf(sc->sc_ah, txq->axq_qnum),
4908 txq->axq_intrcnt = 0; /* reset periodic desc intr count */
4909 bf = STAILQ_FIRST(&txq->axq_q);
4912 ds0 = &bf->bf_desc[0];
4913 ds = &bf->bf_desc[bf->bf_nseg - 1];
4914 ts = &bf->bf_status.ds_txstat;
4915 qbusy = ath_hal_txqenabled(ah, txq->axq_qnum);
4916 status = ath_hal_txprocdesc(ah, ds, ts);
4918 if (sc->sc_debug & ATH_DEBUG_XMIT_DESC)
4919 ath_printtxbuf(sc, bf, txq->axq_qnum, 0,
4922 if (status == HAL_EINPROGRESS) {
4923 #ifdef IEEE80211_SUPPORT_TDMA
4925 * If not done and the queue is not busy then the
4926 * transmitter raced the hardware on the link field
4927 * and we have to restart it.
4931 ath_hal_puttxbuf(ah, txq->axq_qnum,
4933 ath_hal_txstart(ah, txq->axq_qnum);
4938 ATH_TXQ_REMOVE_HEAD(txq, bf_list);
4939 #ifdef IEEE80211_SUPPORT_TDMA
4940 if (txq->axq_depth > 0) {
4942 * More frames follow. Mark the buffer busy
4943 * so it's not re-used while the hardware may
4944 * still re-read the link field in the descriptor.
4946 bf->bf_flags |= ATH_BUF_BUSY;
4949 if (txq->axq_depth == 0)
4951 txq->axq_link = NULL;
4956 if (ts->ts_status == 0) {
4957 u_int8_t txant = ts->ts_antenna;
4958 sc->sc_stats.ast_ant_tx[txant]++;
4959 sc->sc_ant_tx[txant]++;
4960 if (ts->ts_finaltsi != 0)
4961 sc->sc_stats.ast_tx_altrate++;
4962 pri = M_WME_GETAC(bf->bf_m);
4963 if (pri >= WME_AC_VO)
4964 ic->ic_wme.wme_hipri_traffic++;
4965 if ((bf->bf_txflags & HAL_TXDESC_NOACK) == 0)
4966 ni->ni_inact = ni->ni_inact_reload;
4968 if (ts->ts_status & HAL_TXERR_XRETRY)
4969 sc->sc_stats.ast_tx_xretries++;
4970 if (ts->ts_status & HAL_TXERR_FIFO)
4971 sc->sc_stats.ast_tx_fifoerr++;
4972 if (ts->ts_status & HAL_TXERR_FILT)
4973 sc->sc_stats.ast_tx_filtered++;
4974 if (bf->bf_m->m_flags & M_FF)
4975 sc->sc_stats.ast_ff_txerr++;
4977 sr = ts->ts_shortretry;
4978 lr = ts->ts_longretry;
4979 sc->sc_stats.ast_tx_shortretry += sr;
4980 sc->sc_stats.ast_tx_longretry += lr;
4982 * Hand the descriptor to the rate control algorithm.
4984 if ((ts->ts_status & HAL_TXERR_FILT) == 0 &&
4985 (bf->bf_txflags & HAL_TXDESC_NOACK) == 0) {
4987 * If frame was ack'd update statistics,
4988 * including the last rx time used to
4989 * workaround phantom bmiss interrupts.
4991 if (ts->ts_status == 0) {
4993 sc->sc_stats.ast_tx_rssi = ts->ts_rssi;
4994 ATH_RSSI_LPF(sc->sc_halstats.ns_avgtxrssi,
4997 ath_rate_tx_complete(sc, an, bf);
5000 * Do any tx complete callback. Note this must
5001 * be done before releasing the node reference.
5003 if (bf->bf_m->m_flags & M_TXCB)
5004 ieee80211_process_callback(ni, bf->bf_m,
5005 (bf->bf_txflags & HAL_TXDESC_NOACK) == 0 ?
5006 ts->ts_status : HAL_TXERR_XRETRY);
5007 ieee80211_free_node(ni);
5009 bus_dmamap_sync(sc->sc_dmat, bf->bf_dmamap,
5010 BUS_DMASYNC_POSTWRITE);
5011 bus_dmamap_unload(sc->sc_dmat, bf->bf_dmamap);
5017 last = STAILQ_LAST(&sc->sc_txbuf, ath_buf, bf_list);
5019 last->bf_flags &= ~ATH_BUF_BUSY;
5020 STAILQ_INSERT_TAIL(&sc->sc_txbuf, bf, bf_list);
5022 #ifdef IEEE80211_SUPPORT_SUPERG
5024 * Flush fast-frame staging queue when traffic slows.
5026 if (txq->axq_depth <= 1)
5027 ieee80211_ff_flush(ic, txq->axq_ac);
5033 txqactive(struct ath_hal *ah, int qnum)
5035 u_int32_t txqs = 1<<qnum;
5036 ath_hal_gettxintrtxqs(ah, &txqs);
5037 return (txqs & (1<<qnum));
5041 * Deferred processing of transmit interrupt; special-cased
5042 * for a single hardware transmit queue (e.g. 5210 and 5211).
5045 ath_tx_task_q0(void *arg, int npending)
5047 struct ath_softc *sc = arg;
5048 struct ifnet *ifp = sc->sc_ifp;
5050 wlan_serialize_enter();
5051 if (txqactive(sc->sc_ah, 0) && ath_tx_processq(sc, &sc->sc_txq[0]))
5052 sc->sc_lastrx = ath_hal_gettsf64(sc->sc_ah);
5053 if (txqactive(sc->sc_ah, sc->sc_cabq->axq_qnum))
5054 ath_tx_processq(sc, sc->sc_cabq);
5055 ifp->if_flags &= ~IFF_OACTIVE;
5056 sc->sc_wd_timer = 0;
5059 ath_led_event(sc, sc->sc_txrix);
5062 wlan_serialize_exit();
5066 * Deferred processing of transmit interrupt; special-cased
5067 * for four hardware queues, 0-3 (e.g. 5212 w/ WME support).
5070 ath_tx_task_q0123(void *arg, int npending)
5072 struct ath_softc *sc = arg;
5073 struct ifnet *ifp = sc->sc_ifp;
5076 wlan_serialize_enter();
5078 * Process each active queue.
5081 if (txqactive(sc->sc_ah, 0))
5082 nacked += ath_tx_processq(sc, &sc->sc_txq[0]);
5083 if (txqactive(sc->sc_ah, 1))
5084 nacked += ath_tx_processq(sc, &sc->sc_txq[1]);
5085 if (txqactive(sc->sc_ah, 2))
5086 nacked += ath_tx_processq(sc, &sc->sc_txq[2]);
5087 if (txqactive(sc->sc_ah, 3))
5088 nacked += ath_tx_processq(sc, &sc->sc_txq[3]);
5089 if (txqactive(sc->sc_ah, sc->sc_cabq->axq_qnum))
5090 ath_tx_processq(sc, sc->sc_cabq);
5092 sc->sc_lastrx = ath_hal_gettsf64(sc->sc_ah);
5094 ifp->if_flags &= ~IFF_OACTIVE;
5095 sc->sc_wd_timer = 0;
5098 ath_led_event(sc, sc->sc_txrix);
5101 wlan_serialize_exit();
5105 * Deferred processing of transmit interrupt.
5108 ath_tx_task(void *arg, int npending)
5110 struct ath_softc *sc = arg;
5111 struct ifnet *ifp = sc->sc_ifp;
5114 wlan_serialize_enter();
5117 * Process each active queue.
5120 for (i = 0; i < HAL_NUM_TX_QUEUES; i++) {
5121 if (ATH_TXQ_SETUP(sc, i) && txqactive(sc->sc_ah, i))
5122 nacked += ath_tx_processq(sc, &sc->sc_txq[i]);
5125 sc->sc_lastrx = ath_hal_gettsf64(sc->sc_ah);
5127 ifp->if_flags &= ~IFF_OACTIVE;
5128 sc->sc_wd_timer = 0;
5131 ath_led_event(sc, sc->sc_txrix);
5134 wlan_serialize_exit();
5138 ath_tx_draintxq(struct ath_softc *sc, struct ath_txq *txq)
5141 struct ath_hal *ah = sc->sc_ah;
5143 struct ieee80211_node *ni;
5148 * NB: this assumes output has been stopped and
5149 * we do not need to block ath_tx_proc
5151 bf = STAILQ_LAST(&sc->sc_txbuf, ath_buf, bf_list);
5153 bf->bf_flags &= ~ATH_BUF_BUSY;
5154 for (ix = 0;; ix++) {
5155 bf = STAILQ_FIRST(&txq->axq_q);
5157 txq->axq_link = NULL;
5160 ATH_TXQ_REMOVE_HEAD(txq, bf_list);
5162 if (sc->sc_debug & ATH_DEBUG_RESET) {
5163 struct ieee80211com *ic = sc->sc_ifp->if_l2com;
5165 ath_printtxbuf(sc, bf, txq->axq_qnum, ix,
5166 ath_hal_txprocdesc(ah, bf->bf_desc,
5167 &bf->bf_status.ds_txstat) == HAL_OK);
5168 ieee80211_dump_pkt(ic, mtod(bf->bf_m, const uint8_t *),
5169 bf->bf_m->m_len, 0, -1);
5171 #endif /* ATH_DEBUG */
5172 bus_dmamap_unload(sc->sc_dmat, bf->bf_dmamap);
5177 * Do any callback and reclaim the node reference.
5179 if (bf->bf_m->m_flags & M_TXCB)
5180 ieee80211_process_callback(ni, bf->bf_m, -1);
5181 ieee80211_free_node(ni);
5185 bf->bf_flags &= ~ATH_BUF_BUSY;
5187 STAILQ_INSERT_TAIL(&sc->sc_txbuf, bf, bf_list);
5192 ath_tx_stopdma(struct ath_softc *sc, struct ath_txq *txq)
5194 struct ath_hal *ah = sc->sc_ah;
5196 DPRINTF(sc, ATH_DEBUG_RESET, "%s: tx queue [%u] %p, link %p\n",
5197 __func__, txq->axq_qnum,
5198 (caddr_t)(uintptr_t) ath_hal_gettxbuf(ah, txq->axq_qnum),
5200 (void) ath_hal_stoptxdma(ah, txq->axq_qnum);
5204 * Drain the transmit queues and reclaim resources.
5207 ath_draintxq(struct ath_softc *sc)
5209 struct ath_hal *ah = sc->sc_ah;
5210 struct ifnet *ifp = sc->sc_ifp;
5213 /* XXX return value */
5214 if (!sc->sc_invalid) {
5215 /* don't touch the hardware if marked invalid */
5216 DPRINTF(sc, ATH_DEBUG_RESET, "%s: tx queue [%u] %p, link %p\n",
5217 __func__, sc->sc_bhalq,
5218 (caddr_t)(uintptr_t) ath_hal_gettxbuf(ah, sc->sc_bhalq),
5220 (void) ath_hal_stoptxdma(ah, sc->sc_bhalq);
5221 for (i = 0; i < HAL_NUM_TX_QUEUES; i++)
5222 if (ATH_TXQ_SETUP(sc, i))
5223 ath_tx_stopdma(sc, &sc->sc_txq[i]);
5225 for (i = 0; i < HAL_NUM_TX_QUEUES; i++)
5226 if (ATH_TXQ_SETUP(sc, i))
5227 ath_tx_draintxq(sc, &sc->sc_txq[i]);
5229 if (sc->sc_debug & ATH_DEBUG_RESET) {
5230 struct ath_buf *bf = STAILQ_FIRST(&sc->sc_bbuf);
5231 if (bf != NULL && bf->bf_m != NULL) {
5232 ath_printtxbuf(sc, bf, sc->sc_bhalq, 0,
5233 ath_hal_txprocdesc(ah, bf->bf_desc,
5234 &bf->bf_status.ds_txstat) == HAL_OK);
5235 ieee80211_dump_pkt(ifp->if_l2com,
5236 mtod(bf->bf_m, const uint8_t *), bf->bf_m->m_len,
5240 #endif /* ATH_DEBUG */
5241 ifp->if_flags &= ~IFF_OACTIVE;
5242 sc->sc_wd_timer = 0;
5246 * Disable the receive h/w in preparation for a reset.
5249 ath_stoprecv(struct ath_softc *sc)
5251 #define PA2DESC(_sc, _pa) \
5252 ((struct ath_desc *)((caddr_t)(_sc)->sc_rxdma.dd_desc + \
5253 ((_pa) - (_sc)->sc_rxdma.dd_desc_paddr)))
5254 struct ath_hal *ah = sc->sc_ah;
5256 ath_hal_stoppcurecv(ah); /* disable PCU */
5257 ath_hal_setrxfilter(ah, 0); /* clear recv filter */
5258 ath_hal_stopdmarecv(ah); /* disable DMA engine */
5259 DELAY(3000); /* 3ms is long enough for 1 frame */
5261 if (sc->sc_debug & (ATH_DEBUG_RESET | ATH_DEBUG_FATAL)) {
5265 kprintf("%s: rx queue %p, link %p\n", __func__,
5266 (caddr_t)(uintptr_t) ath_hal_getrxbuf(ah), sc->sc_rxlink);
5268 STAILQ_FOREACH(bf, &sc->sc_rxbuf, bf_list) {
5269 struct ath_desc *ds = bf->bf_desc;
5270 struct ath_rx_status *rs = &bf->bf_status.ds_rxstat;
5271 HAL_STATUS status = ath_hal_rxprocdesc(ah, ds,
5272 bf->bf_daddr, PA2DESC(sc, ds->ds_link), rs);
5273 if (status == HAL_OK || (sc->sc_debug & ATH_DEBUG_FATAL))
5274 ath_printrxbuf(sc, bf, ix, status == HAL_OK);
5279 if (sc->sc_rxpending != NULL) {
5280 m_freem(sc->sc_rxpending);
5281 sc->sc_rxpending = NULL;
5283 sc->sc_rxlink = NULL; /* just in case */
5288 * Enable the receive h/w following a reset.
5291 ath_startrecv(struct ath_softc *sc)
5293 struct ath_hal *ah = sc->sc_ah;
5296 sc->sc_rxlink = NULL;
5297 sc->sc_rxpending = NULL;
5298 STAILQ_FOREACH(bf, &sc->sc_rxbuf, bf_list) {
5299 int error = ath_rxbuf_init(sc, bf);
5301 DPRINTF(sc, ATH_DEBUG_RECV,
5302 "%s: ath_rxbuf_init failed %d\n",
5308 bf = STAILQ_FIRST(&sc->sc_rxbuf);
5309 ath_hal_putrxbuf(ah, bf->bf_daddr);
5310 ath_hal_rxena(ah); /* enable recv descriptors */
5311 ath_mode_init(sc); /* set filters, etc. */
5312 ath_hal_startpcurecv(ah); /* re-enable PCU/DMA engine */
5317 * Update internal state after a channel change.
5320 ath_chan_change(struct ath_softc *sc, struct ieee80211_channel *chan)
5322 enum ieee80211_phymode mode;
5325 * Change channels and update the h/w rate map
5326 * if we're switching; e.g. 11a to 11b/g.
5328 mode = ieee80211_chan2mode(chan);
5329 if (mode != sc->sc_curmode)
5330 ath_setcurmode(sc, mode);
5331 sc->sc_curchan = chan;
5335 * Set/change channels. If the channel is really being changed,
5336 * it's done by reseting the chip. To accomplish this we must
5337 * first cleanup any pending DMA, then restart stuff after a la
5341 ath_chan_set(struct ath_softc *sc, struct ieee80211_channel *chan)
5343 struct ifnet *ifp = sc->sc_ifp;
5344 struct ieee80211com *ic = ifp->if_l2com;
5345 struct ath_hal *ah = sc->sc_ah;
5347 DPRINTF(sc, ATH_DEBUG_RESET, "%s: %u (%u MHz, flags 0x%x)\n",
5348 __func__, ieee80211_chan2ieee(ic, chan),
5349 chan->ic_freq, chan->ic_flags);
5350 if (chan != sc->sc_curchan) {
5353 * To switch channels clear any pending DMA operations;
5354 * wait long enough for the RX fifo to drain, reset the
5355 * hardware at the new frequency, and then re-enable
5356 * the relevant bits of the h/w.
5358 ath_hal_intrset(ah, 0); /* disable interrupts */
5359 ath_draintxq(sc); /* clear pending tx frames */
5360 ath_stoprecv(sc); /* turn off frame recv */
5361 if (!ath_hal_reset(ah, sc->sc_opmode, chan, AH_TRUE, &status)) {
5362 if_printf(ifp, "%s: unable to reset "
5363 "channel %u (%u MHz, flags 0x%x), hal status %u\n",
5364 __func__, ieee80211_chan2ieee(ic, chan),
5365 chan->ic_freq, chan->ic_flags, status);
5368 sc->sc_diversity = ath_hal_getdiversity(ah);
5371 * Re-enable rx framework.
5373 if (ath_startrecv(sc) != 0) {
5374 if_printf(ifp, "%s: unable to restart recv logic\n",
5380 * Change channels and update the h/w rate map
5381 * if we're switching; e.g. 11a to 11b/g.
5383 ath_chan_change(sc, chan);
5386 * Re-enable interrupts.
5388 ath_hal_intrset(ah, sc->sc_imask);
5394 * Periodically recalibrate the PHY to account
5395 * for temperature/environment changes.
5398 ath_calibrate_callout(void *arg)
5400 struct ath_softc *sc = arg;
5401 struct ath_hal *ah = sc->sc_ah;
5402 struct ifnet *ifp = sc->sc_ifp;
5403 struct ieee80211com *ic = ifp->if_l2com;
5404 HAL_BOOL longCal, isCalDone;
5407 wlan_serialize_enter();
5409 if (ic->ic_flags & IEEE80211_F_SCAN) /* defer, off channel */
5411 longCal = (ticks - sc->sc_lastlongcal >= ath_longcalinterval*hz);
5413 sc->sc_stats.ast_per_cal++;
5414 sc->sc_lastlongcal = ticks;
5415 if (ath_hal_getrfgain(ah) == HAL_RFGAIN_NEED_CHANGE) {
5417 * Rfgain is out of bounds, reset the chip
5418 * to load new gain values.
5420 DPRINTF(sc, ATH_DEBUG_CALIBRATE,
5421 "%s: rfgain change\n", __func__);
5422 sc->sc_stats.ast_per_rfgain++;
5426 * If this long cal is after an idle period, then
5427 * reset the data collection state so we start fresh.
5429 if (sc->sc_resetcal) {
5430 (void) ath_hal_calreset(ah, sc->sc_curchan);
5431 sc->sc_lastcalreset = ticks;
5432 sc->sc_resetcal = 0;
5435 if (ath_hal_calibrateN(ah, sc->sc_curchan, longCal, &isCalDone)) {
5438 * Calibrate noise floor data again in case of change.
5440 ath_hal_process_noisefloor(ah);
5443 DPRINTF(sc, ATH_DEBUG_ANY,
5444 "%s: calibration of channel %u failed\n",
5445 __func__, sc->sc_curchan->ic_freq);
5446 sc->sc_stats.ast_per_calfail++;
5451 * Use a shorter interval to potentially collect multiple
5452 * data samples required to complete calibration. Once
5453 * we're told the work is done we drop back to a longer
5454 * interval between requests. We're more aggressive doing
5455 * work when operating as an AP to improve operation right
5458 nextcal = (1000*ath_shortcalinterval)/hz;
5459 if (sc->sc_opmode != HAL_M_HOSTAP)
5462 nextcal = ath_longcalinterval*hz;
5463 if (sc->sc_lastcalreset == 0)
5464 sc->sc_lastcalreset = sc->sc_lastlongcal;
5465 else if (ticks - sc->sc_lastcalreset >= ath_resetcalinterval*hz)
5466 sc->sc_resetcal = 1; /* setup reset next trip */
5470 DPRINTF(sc, ATH_DEBUG_CALIBRATE, "%s: next +%u (%sisCalDone)\n",
5471 __func__, nextcal, isCalDone ? "" : "!");
5472 callout_reset(&sc->sc_cal_ch, nextcal,
5473 ath_calibrate_callout, sc);
5475 DPRINTF(sc, ATH_DEBUG_CALIBRATE, "%s: calibration disabled\n",
5477 /* NB: don't rearm timer */
5479 wlan_serialize_exit();
5483 ath_scan_start(struct ieee80211com *ic)
5485 struct ifnet *ifp = ic->ic_ifp;
5486 struct ath_softc *sc = ifp->if_softc;
5487 struct ath_hal *ah = sc->sc_ah;
5490 /* XXX calibration timer? */
5492 sc->sc_scanning = 1;
5493 sc->sc_syncbeacon = 0;
5494 rfilt = ath_calcrxfilter(sc);
5495 ath_hal_setrxfilter(ah, rfilt);
5496 ath_hal_setassocid(ah, ifp->if_broadcastaddr, 0);
5498 DPRINTF(sc, ATH_DEBUG_STATE, "%s: RX filter 0x%x bssid %6D aid 0\n",
5499 __func__, rfilt, ifp->if_broadcastaddr, ":");
5503 ath_scan_end(struct ieee80211com *ic)
5505 struct ifnet *ifp = ic->ic_ifp;
5506 struct ath_softc *sc = ifp->if_softc;
5507 struct ath_hal *ah = sc->sc_ah;
5510 sc->sc_scanning = 0;
5511 rfilt = ath_calcrxfilter(sc);
5512 ath_hal_setrxfilter(ah, rfilt);
5513 ath_hal_setassocid(ah, sc->sc_curbssid, sc->sc_curaid);
5515 ath_hal_process_noisefloor(ah);
5517 DPRINTF(sc, ATH_DEBUG_STATE, "%s: RX filter 0x%x bssid %6D aid 0x%x\n",
5518 __func__, rfilt, sc->sc_curbssid, ":",
5523 ath_set_channel(struct ieee80211com *ic)
5525 struct ifnet *ifp = ic->ic_ifp;
5526 struct ath_softc *sc = ifp->if_softc;
5528 (void) ath_chan_set(sc, ic->ic_curchan);
5530 * If we are returning to our bss channel then mark state
5531 * so the next recv'd beacon's tsf will be used to sync the
5532 * beacon timers. Note that since we only hear beacons in
5533 * sta/ibss mode this has no effect in other operating modes.
5535 if (!sc->sc_scanning && ic->ic_curchan == ic->ic_bsschan)
5536 sc->sc_syncbeacon = 1;
5540 * Walk the vap list and check if there any vap's in RUN state.
5543 ath_isanyrunningvaps(struct ieee80211vap *this)
5545 struct ieee80211com *ic = this->iv_ic;
5546 struct ieee80211vap *vap;
5548 TAILQ_FOREACH(vap, &ic->ic_vaps, iv_next) {
5549 if (vap != this && vap->iv_state >= IEEE80211_S_RUN)
5556 ath_newstate(struct ieee80211vap *vap, enum ieee80211_state nstate, int arg)
5558 struct ieee80211com *ic = vap->iv_ic;
5559 struct ath_softc *sc = ic->ic_ifp->if_softc;
5560 struct ath_vap *avp = ATH_VAP(vap);
5561 struct ath_hal *ah = sc->sc_ah;
5562 struct ieee80211_node *ni = NULL;
5563 int i, error, stamode;
5565 static const HAL_LED_STATE leds[] = {
5566 HAL_LED_INIT, /* IEEE80211_S_INIT */
5567 HAL_LED_SCAN, /* IEEE80211_S_SCAN */
5568 HAL_LED_AUTH, /* IEEE80211_S_AUTH */
5569 HAL_LED_ASSOC, /* IEEE80211_S_ASSOC */
5570 HAL_LED_RUN, /* IEEE80211_S_CAC */
5571 HAL_LED_RUN, /* IEEE80211_S_RUN */
5572 HAL_LED_RUN, /* IEEE80211_S_CSA */
5573 HAL_LED_RUN, /* IEEE80211_S_SLEEP */
5576 DPRINTF(sc, ATH_DEBUG_STATE, "%s: %s -> %s\n", __func__,
5577 ieee80211_state_name[vap->iv_state],
5578 ieee80211_state_name[nstate]);
5580 callout_stop(&sc->sc_cal_ch);
5581 ath_hal_setledstate(ah, leds[nstate]); /* set LED */
5583 if (nstate == IEEE80211_S_SCAN) {
5585 * Scanning: turn off beacon miss and don't beacon.
5586 * Mark beacon state so when we reach RUN state we'll
5587 * [re]setup beacons. Unblock the task q thread so
5588 * deferred interrupt processing is done.
5591 sc->sc_imask &~ (HAL_INT_SWBA | HAL_INT_BMISS));
5592 sc->sc_imask &= ~(HAL_INT_SWBA | HAL_INT_BMISS);
5594 taskqueue_unblock(sc->sc_tq);
5598 rfilt = ath_calcrxfilter(sc);
5599 stamode = (vap->iv_opmode == IEEE80211_M_STA ||
5600 vap->iv_opmode == IEEE80211_M_AHDEMO ||
5601 vap->iv_opmode == IEEE80211_M_IBSS);
5602 if (stamode && nstate == IEEE80211_S_RUN) {
5603 sc->sc_curaid = ni->ni_associd;
5604 IEEE80211_ADDR_COPY(sc->sc_curbssid, ni->ni_bssid);
5605 ath_hal_setassocid(ah, sc->sc_curbssid, sc->sc_curaid);
5607 DPRINTF(sc, ATH_DEBUG_STATE, "%s: RX filter 0x%x bssid %6D aid 0x%x\n",
5608 __func__, rfilt, sc->sc_curbssid, ":", sc->sc_curaid);
5609 ath_hal_setrxfilter(ah, rfilt);
5611 /* XXX is this to restore keycache on resume? */
5612 if (vap->iv_opmode != IEEE80211_M_STA &&
5613 (vap->iv_flags & IEEE80211_F_PRIVACY)) {
5614 for (i = 0; i < IEEE80211_WEP_NKID; i++)
5615 if (ath_hal_keyisvalid(ah, i))
5616 ath_hal_keysetmac(ah, i, ni->ni_bssid);
5620 * Invoke the parent method to do net80211 work.
5622 error = avp->av_newstate(vap, nstate, arg);
5626 if (nstate == IEEE80211_S_RUN) {
5627 /* NB: collect bss node again, it may have changed */
5630 DPRINTF(sc, ATH_DEBUG_STATE,
5631 "%s(RUN): iv_flags 0x%08x bintvl %d bssid %6D "
5632 "capinfo 0x%04x chan %d\n", __func__,
5633 vap->iv_flags, ni->ni_intval, ni->ni_bssid, ":",
5634 ni->ni_capinfo, ieee80211_chan2ieee(ic, ic->ic_curchan));
5636 switch (vap->iv_opmode) {
5637 #ifdef IEEE80211_SUPPORT_TDMA
5638 case IEEE80211_M_AHDEMO:
5639 if ((vap->iv_caps & IEEE80211_C_TDMA) == 0)
5643 case IEEE80211_M_HOSTAP:
5644 case IEEE80211_M_IBSS:
5645 case IEEE80211_M_MBSS:
5647 * Allocate and setup the beacon frame.
5649 * Stop any previous beacon DMA. This may be
5650 * necessary, for example, when an ibss merge
5651 * causes reconfiguration; there will be a state
5652 * transition from RUN->RUN that means we may
5653 * be called with beacon transmission active.
5655 ath_hal_stoptxdma(ah, sc->sc_bhalq);
5657 error = ath_beacon_alloc(sc, ni);
5661 * If joining an adhoc network defer beacon timer
5662 * configuration to the next beacon frame so we
5663 * have a current TSF to use. Otherwise we're
5664 * starting an ibss/bss so there's no need to delay;
5665 * if this is the first vap moving to RUN state, then
5666 * beacon state needs to be [re]configured.
5668 if (vap->iv_opmode == IEEE80211_M_IBSS &&
5669 ni->ni_tstamp.tsf != 0) {
5670 sc->sc_syncbeacon = 1;
5671 } else if (!sc->sc_beacons) {
5672 #ifdef IEEE80211_SUPPORT_TDMA
5673 if (vap->iv_caps & IEEE80211_C_TDMA)
5674 ath_tdma_config(sc, vap);
5677 ath_beacon_config(sc, vap);
5681 case IEEE80211_M_STA:
5683 * Defer beacon timer configuration to the next
5684 * beacon frame so we have a current TSF to use
5685 * (any TSF collected when scanning is likely old).
5687 sc->sc_syncbeacon = 1;
5689 case IEEE80211_M_MONITOR:
5691 * Monitor mode vaps have only INIT->RUN and RUN->RUN
5692 * transitions so we must re-enable interrupts here to
5693 * handle the case of a single monitor mode vap.
5695 ath_hal_intrset(ah, sc->sc_imask);
5697 case IEEE80211_M_WDS:
5703 * Let the hal process statistics collected during a
5704 * scan so it can provide calibrated noise floor data.
5706 ath_hal_process_noisefloor(ah);
5708 * Reset rssi stats; maybe not the best place...
5710 sc->sc_halstats.ns_avgbrssi = ATH_RSSI_DUMMY_MARKER;
5711 sc->sc_halstats.ns_avgrssi = ATH_RSSI_DUMMY_MARKER;
5712 sc->sc_halstats.ns_avgtxrssi = ATH_RSSI_DUMMY_MARKER;
5714 * Finally, start any timers and the task q thread
5715 * (in case we didn't go through SCAN state).
5717 if (ath_longcalinterval != 0) {
5718 /* start periodic recalibration timer */
5719 callout_reset(&sc->sc_cal_ch, 1,
5720 ath_calibrate_callout, sc);
5722 DPRINTF(sc, ATH_DEBUG_CALIBRATE,
5723 "%s: calibration disabled\n", __func__);
5725 taskqueue_unblock(sc->sc_tq);
5726 } else if (nstate == IEEE80211_S_INIT) {
5728 * If there are no vaps left in RUN state then
5729 * shutdown host/driver operation:
5730 * o disable interrupts
5731 * o disable the task queue thread
5732 * o mark beacon processing as stopped
5734 if (!ath_isanyrunningvaps(vap)) {
5735 sc->sc_imask &= ~(HAL_INT_SWBA | HAL_INT_BMISS);
5736 /* disable interrupts */
5737 ath_hal_intrset(ah, sc->sc_imask &~ HAL_INT_GLOBAL);
5738 taskqueue_block(sc->sc_tq);
5741 #ifdef IEEE80211_SUPPORT_TDMA
5742 ath_hal_setcca(ah, AH_TRUE);
5750 * Allocate a key cache slot to the station so we can
5751 * setup a mapping from key index to node. The key cache
5752 * slot is needed for managing antenna state and for
5753 * compression when stations do not use crypto. We do
5754 * it uniliaterally here; if crypto is employed this slot
5755 * will be reassigned.
5758 ath_setup_stationkey(struct ieee80211_node *ni)
5760 struct ieee80211vap *vap = ni->ni_vap;
5761 struct ath_softc *sc = vap->iv_ic->ic_ifp->if_softc;
5762 ieee80211_keyix keyix, rxkeyix;
5764 if (!ath_key_alloc(vap, &ni->ni_ucastkey, &keyix, &rxkeyix)) {
5766 * Key cache is full; we'll fall back to doing
5767 * the more expensive lookup in software. Note
5768 * this also means no h/w compression.
5770 /* XXX msg+statistic */
5773 ni->ni_ucastkey.wk_keyix = keyix;
5774 ni->ni_ucastkey.wk_rxkeyix = rxkeyix;
5775 /* NB: must mark device key to get called back on delete */
5776 ni->ni_ucastkey.wk_flags |= IEEE80211_KEY_DEVKEY;
5777 IEEE80211_ADDR_COPY(ni->ni_ucastkey.wk_macaddr, ni->ni_macaddr);
5778 /* NB: this will create a pass-thru key entry */
5779 ath_keyset(sc, &ni->ni_ucastkey, vap->iv_bss);
5784 * Setup driver-specific state for a newly associated node.
5785 * Note that we're called also on a re-associate, the isnew
5786 * param tells us if this is the first time or not.
5789 ath_newassoc(struct ieee80211_node *ni, int isnew)
5791 struct ath_node *an = ATH_NODE(ni);
5792 struct ieee80211vap *vap = ni->ni_vap;
5793 struct ath_softc *sc = vap->iv_ic->ic_ifp->if_softc;
5794 const struct ieee80211_txparam *tp = ni->ni_txparms;
5796 an->an_mcastrix = ath_tx_findrix(sc, tp->mcastrate);
5797 an->an_mgmtrix = ath_tx_findrix(sc, tp->mgmtrate);
5799 ath_rate_newassoc(sc, an, isnew);
5801 (vap->iv_flags & IEEE80211_F_PRIVACY) == 0 && sc->sc_hasclrkey &&
5802 ni->ni_ucastkey.wk_keyix == IEEE80211_KEYIX_NONE)
5803 ath_setup_stationkey(ni);
5807 ath_setregdomain(struct ieee80211com *ic, struct ieee80211_regdomain *reg,
5808 int nchans, struct ieee80211_channel chans[])
5810 struct ath_softc *sc = ic->ic_ifp->if_softc;
5811 struct ath_hal *ah = sc->sc_ah;
5814 DPRINTF(sc, ATH_DEBUG_REGDOMAIN,
5815 "%s: rd %u cc %u location %c%s\n",
5816 __func__, reg->regdomain, reg->country, reg->location,
5817 reg->ecm ? " ecm" : "");
5819 status = ath_hal_set_channels(ah, chans, nchans,
5820 reg->country, reg->regdomain);
5821 if (status != HAL_OK) {
5822 DPRINTF(sc, ATH_DEBUG_REGDOMAIN, "%s: failed, status %u\n",
5824 return EINVAL; /* XXX */
5830 ath_getradiocaps(struct ieee80211com *ic,
5831 int maxchans, int *nchans, struct ieee80211_channel chans[])
5833 struct ath_softc *sc = ic->ic_ifp->if_softc;
5834 struct ath_hal *ah = sc->sc_ah;
5836 DPRINTF(sc, ATH_DEBUG_REGDOMAIN, "%s: use rd %u cc %d\n",
5837 __func__, SKU_DEBUG, CTRY_DEFAULT);
5839 /* XXX check return */
5840 (void) ath_hal_getchannels(ah, chans, maxchans, nchans,
5841 HAL_MODE_ALL, CTRY_DEFAULT, SKU_DEBUG, AH_TRUE);
5846 ath_getchannels(struct ath_softc *sc)
5848 struct ifnet *ifp = sc->sc_ifp;
5849 struct ieee80211com *ic = ifp->if_l2com;
5850 struct ath_hal *ah = sc->sc_ah;
5854 * Collect channel set based on EEPROM contents.
5856 status = ath_hal_init_channels(ah, ic->ic_channels, IEEE80211_CHAN_MAX,
5857 &ic->ic_nchans, HAL_MODE_ALL, CTRY_DEFAULT, SKU_NONE, AH_TRUE);
5858 if (status != HAL_OK) {
5859 if_printf(ifp, "%s: unable to collect channel list from hal, "
5860 "status %d\n", __func__, status);
5863 (void) ath_hal_getregdomain(ah, &sc->sc_eerd);
5864 ath_hal_getcountrycode(ah, &sc->sc_eecc); /* NB: cannot fail */
5865 /* XXX map Atheros sku's to net80211 SKU's */
5866 /* XXX net80211 types too small */
5867 ic->ic_regdomain.regdomain = (uint16_t) sc->sc_eerd;
5868 ic->ic_regdomain.country = (uint16_t) sc->sc_eecc;
5869 ic->ic_regdomain.isocc[0] = ' '; /* XXX don't know */
5870 ic->ic_regdomain.isocc[1] = ' ';
5872 ic->ic_regdomain.ecm = 1;
5873 ic->ic_regdomain.location = 'I';
5875 DPRINTF(sc, ATH_DEBUG_REGDOMAIN,
5876 "%s: eeprom rd %u cc %u (mapped rd %u cc %u) location %c%s\n",
5877 __func__, sc->sc_eerd, sc->sc_eecc,
5878 ic->ic_regdomain.regdomain, ic->ic_regdomain.country,
5879 ic->ic_regdomain.location, ic->ic_regdomain.ecm ? " ecm" : "");
5884 ath_led_done_callout(void *arg)
5886 struct ath_softc *sc = arg;
5888 wlan_serialize_enter();
5889 sc->sc_blinking = 0;
5890 wlan_serialize_exit();
5894 * Turn the LED off: flip the pin and then set a timer so no
5895 * update will happen for the specified duration.
5898 ath_led_off_callout(void *arg)
5900 struct ath_softc *sc = arg;
5902 wlan_serialize_enter();
5903 ath_hal_gpioset(sc->sc_ah, sc->sc_ledpin, !sc->sc_ledon);
5904 callout_reset(&sc->sc_ledtimer, sc->sc_ledoff,
5905 ath_led_done_callout, sc);
5906 wlan_serialize_exit();
5910 * Blink the LED according to the specified on/off times.
5913 ath_led_blink(struct ath_softc *sc, int on, int off)
5915 DPRINTF(sc, ATH_DEBUG_LED, "%s: on %u off %u\n", __func__, on, off);
5916 ath_hal_gpioset(sc->sc_ah, sc->sc_ledpin, sc->sc_ledon);
5917 sc->sc_blinking = 1;
5918 sc->sc_ledoff = off;
5919 callout_reset(&sc->sc_ledtimer, on, ath_led_off_callout, sc);
5923 ath_led_event(struct ath_softc *sc, int rix)
5925 sc->sc_ledevent = ticks; /* time of last event */
5926 if (sc->sc_blinking) /* don't interrupt active blink */
5928 ath_led_blink(sc, sc->sc_hwmap[rix].ledon, sc->sc_hwmap[rix].ledoff);
5932 ath_rate_setup(struct ath_softc *sc, u_int mode)
5934 struct ath_hal *ah = sc->sc_ah;
5935 const HAL_RATE_TABLE *rt;
5938 case IEEE80211_MODE_11A:
5939 rt = ath_hal_getratetable(ah, HAL_MODE_11A);
5941 case IEEE80211_MODE_HALF:
5942 rt = ath_hal_getratetable(ah, HAL_MODE_11A_HALF_RATE);
5944 case IEEE80211_MODE_QUARTER:
5945 rt = ath_hal_getratetable(ah, HAL_MODE_11A_QUARTER_RATE);
5947 case IEEE80211_MODE_11B:
5948 rt = ath_hal_getratetable(ah, HAL_MODE_11B);
5950 case IEEE80211_MODE_11G:
5951 rt = ath_hal_getratetable(ah, HAL_MODE_11G);
5953 case IEEE80211_MODE_TURBO_A:
5954 rt = ath_hal_getratetable(ah, HAL_MODE_108A);
5956 case IEEE80211_MODE_TURBO_G:
5957 rt = ath_hal_getratetable(ah, HAL_MODE_108G);
5959 case IEEE80211_MODE_STURBO_A:
5960 rt = ath_hal_getratetable(ah, HAL_MODE_TURBO);
5962 case IEEE80211_MODE_11NA:
5963 rt = ath_hal_getratetable(ah, HAL_MODE_11NA_HT20);
5965 case IEEE80211_MODE_11NG:
5966 rt = ath_hal_getratetable(ah, HAL_MODE_11NG_HT20);
5969 DPRINTF(sc, ATH_DEBUG_ANY, "%s: invalid mode %u\n",
5973 sc->sc_rates[mode] = rt;
5974 return (rt != NULL);
5978 ath_setcurmode(struct ath_softc *sc, enum ieee80211_phymode mode)
5980 /* NB: on/off times from the Atheros NDIS driver, w/ permission */
5981 static const struct {
5982 u_int rate; /* tx/rx 802.11 rate */
5983 u_int16_t timeOn; /* LED on time (ms) */
5984 u_int16_t timeOff; /* LED off time (ms) */
6000 /* XXX half/quarter rates */
6002 const HAL_RATE_TABLE *rt;
6005 memset(sc->sc_rixmap, 0xff, sizeof(sc->sc_rixmap));
6006 rt = sc->sc_rates[mode];
6007 KASSERT(rt != NULL, ("no h/w rate set for phy mode %u", mode));
6008 for (i = 0; i < rt->rateCount; i++) {
6009 uint8_t ieeerate = rt->info[i].dot11Rate & IEEE80211_RATE_VAL;
6010 if (rt->info[i].phy != IEEE80211_T_HT)
6011 sc->sc_rixmap[ieeerate] = i;
6013 sc->sc_rixmap[ieeerate | IEEE80211_RATE_MCS] = i;
6015 memset(sc->sc_hwmap, 0, sizeof(sc->sc_hwmap));
6016 for (i = 0; i < NELEM(sc->sc_hwmap); i++) {
6017 if (i >= rt->rateCount) {
6018 sc->sc_hwmap[i].ledon = (500 * hz) / 1000;
6019 sc->sc_hwmap[i].ledoff = (130 * hz) / 1000;
6022 sc->sc_hwmap[i].ieeerate =
6023 rt->info[i].dot11Rate & IEEE80211_RATE_VAL;
6024 if (rt->info[i].phy == IEEE80211_T_HT)
6025 sc->sc_hwmap[i].ieeerate |= IEEE80211_RATE_MCS;
6026 sc->sc_hwmap[i].txflags = IEEE80211_RADIOTAP_F_DATAPAD;
6027 if (rt->info[i].shortPreamble ||
6028 rt->info[i].phy == IEEE80211_T_OFDM)
6029 sc->sc_hwmap[i].txflags |= IEEE80211_RADIOTAP_F_SHORTPRE;
6030 sc->sc_hwmap[i].rxflags = sc->sc_hwmap[i].txflags;
6031 for (j = 0; j < NELEM(blinkrates)-1; j++)
6032 if (blinkrates[j].rate == sc->sc_hwmap[i].ieeerate)
6034 /* NB: this uses the last entry if the rate isn't found */
6035 /* XXX beware of overlow */
6036 sc->sc_hwmap[i].ledon = (blinkrates[j].timeOn * hz) / 1000;
6037 sc->sc_hwmap[i].ledoff = (blinkrates[j].timeOff * hz) / 1000;
6039 sc->sc_currates = rt;
6040 sc->sc_curmode = mode;
6042 * All protection frames are transmited at 2Mb/s for
6043 * 11g, otherwise at 1Mb/s.
6045 if (mode == IEEE80211_MODE_11G)
6046 sc->sc_protrix = ath_tx_findrix(sc, 2*2);
6048 sc->sc_protrix = ath_tx_findrix(sc, 2*1);
6049 /* NB: caller is responsible for reseting rate control state */
6054 ath_printrxbuf(struct ath_softc *sc, const struct ath_buf *bf,
6057 const struct ath_rx_status *rs = &bf->bf_status.ds_rxstat;
6058 struct ath_hal *ah = sc->sc_ah;
6059 const struct ath_desc *ds;
6062 for (i = 0, ds = bf->bf_desc; i < bf->bf_nseg; i++, ds++) {
6063 kprintf("R[%2u] (DS.V:%p DS.P:%p) L:%08x D:%08x%s\n"
6064 " %08x %08x %08x %08x\n",
6065 ix, ds, (const struct ath_desc *)bf->bf_daddr + i,
6066 ds->ds_link, ds->ds_data,
6067 !done ? "" : (rs->rs_status == 0) ? " *" : " !",
6068 ds->ds_ctl0, ds->ds_ctl1,
6069 ds->ds_hw[0], ds->ds_hw[1]);
6070 if (ah->ah_magic == 0x20065416) {
6071 kprintf(" %08x %08x %08x %08x %08x %08x %08x\n",
6072 ds->ds_hw[2], ds->ds_hw[3], ds->ds_hw[4],
6073 ds->ds_hw[5], ds->ds_hw[6], ds->ds_hw[7],
6080 ath_printtxbuf(struct ath_softc *sc, const struct ath_buf *bf,
6081 u_int qnum, u_int ix, int done)
6083 const struct ath_tx_status *ts = &bf->bf_status.ds_txstat;
6084 struct ath_hal *ah = sc->sc_ah;
6085 const struct ath_desc *ds;
6088 kprintf("Q%u[%3u]", qnum, ix);
6089 for (i = 0, ds = bf->bf_desc; i < bf->bf_nseg; i++, ds++) {
6090 kprintf(" (DS.V:%p DS.P:%p) L:%08x D:%08x F:04%x%s\n"
6091 " %08x %08x %08x %08x %08x %08x\n",
6092 ds, (const struct ath_desc *)bf->bf_daddr + i,
6093 ds->ds_link, ds->ds_data, bf->bf_txflags,
6094 !done ? "" : (ts->ts_status == 0) ? " *" : " !",
6095 ds->ds_ctl0, ds->ds_ctl1,
6096 ds->ds_hw[0], ds->ds_hw[1], ds->ds_hw[2], ds->ds_hw[3]);
6097 if (ah->ah_magic == 0x20065416) {
6098 kprintf(" %08x %08x %08x %08x %08x %08x %08x %08x\n",
6099 ds->ds_hw[4], ds->ds_hw[5], ds->ds_hw[6],
6100 ds->ds_hw[7], ds->ds_hw[8], ds->ds_hw[9],
6101 ds->ds_hw[10],ds->ds_hw[11]);
6102 kprintf(" %08x %08x %08x %08x %08x %08x %08x %08x\n",
6103 ds->ds_hw[12],ds->ds_hw[13],ds->ds_hw[14],
6104 ds->ds_hw[15],ds->ds_hw[16],ds->ds_hw[17],
6105 ds->ds_hw[18], ds->ds_hw[19]);
6109 #endif /* ATH_DEBUG */
6112 ath_watchdog_callout(void *arg)
6114 struct ath_softc *sc = arg;
6116 wlan_serialize_enter();
6117 if (sc->sc_wd_timer != 0 && --sc->sc_wd_timer == 0) {
6118 struct ifnet *ifp = sc->sc_ifp;
6121 if (ath_hal_gethangstate(sc->sc_ah, 0xffff, &hangs) &&
6123 if_printf(ifp, "%s hang detected (0x%x)\n",
6124 hangs & 0xff ? "bb" : "mac", hangs);
6126 if_printf(ifp, "device timeout\n");
6129 sc->sc_stats.ast_watchdog++;
6131 callout_reset(&sc->sc_wd_ch, hz, ath_watchdog_callout, sc);
6132 wlan_serialize_exit();
6137 * Diagnostic interface to the HAL. This is used by various
6138 * tools to do things like retrieve register contents for
6139 * debugging. The mechanism is intentionally opaque so that
6140 * it can change frequently w/o concern for compatiblity.
6143 ath_ioctl_diag(struct ath_softc *sc, struct ath_diag *ad)
6145 struct ath_hal *ah = sc->sc_ah;
6146 u_int id = ad->ad_id & ATH_DIAG_ID;
6147 void *indata = NULL;
6148 void *outdata = NULL;
6149 u_int32_t insize = ad->ad_in_size;
6150 u_int32_t outsize = ad->ad_out_size;
6153 if (ad->ad_id & ATH_DIAG_IN) {
6157 indata = kmalloc(insize, M_TEMP, M_INTWAIT);
6158 if (indata == NULL) {
6162 error = copyin(ad->ad_in_data, indata, insize);
6166 if (ad->ad_id & ATH_DIAG_DYN) {
6168 * Allocate a buffer for the results (otherwise the HAL
6169 * returns a pointer to a buffer where we can read the
6170 * results). Note that we depend on the HAL leaving this
6171 * pointer for us to use below in reclaiming the buffer;
6172 * may want to be more defensive.
6174 outdata = kmalloc(outsize, M_TEMP, M_INTWAIT);
6175 if (outdata == NULL) {
6180 if (ath_hal_getdiagstate(ah, id, indata, insize, &outdata, &outsize)) {
6181 if (outsize < ad->ad_out_size)
6182 ad->ad_out_size = outsize;
6183 if (outdata != NULL)
6184 error = copyout(outdata, ad->ad_out_data,
6190 if ((ad->ad_id & ATH_DIAG_IN) && indata != NULL)
6191 kfree(indata, M_TEMP);
6192 if ((ad->ad_id & ATH_DIAG_DYN) && outdata != NULL)
6193 kfree(outdata, M_TEMP);
6196 #endif /* ATH_DIAGAPI */
6199 ath_ioctl(struct ifnet *ifp, u_long cmd, caddr_t data, struct ucred *ucred)
6201 #define IS_RUNNING(ifp) \
6202 ((ifp->if_flags & IFF_UP) && (ifp->if_flags & IFF_RUNNING))
6203 struct ath_softc *sc = ifp->if_softc;
6204 struct ieee80211com *ic = ifp->if_l2com;
6205 struct ifreq *ifr = (struct ifreq *)data;
6206 const HAL_RATE_TABLE *rt;
6211 if (IS_RUNNING(ifp)) {
6213 * To avoid rescanning another access point,
6214 * do not call ath_init() here. Instead,
6215 * only reflect promisc mode settings.
6218 } else if (ifp->if_flags & IFF_UP) {
6220 * Beware of being called during attach/detach
6221 * to reset promiscuous mode. In that case we
6222 * will still be marked UP but not RUNNING.
6223 * However trying to re-init the interface
6224 * is the wrong thing to do as we've already
6225 * torn down much of our state. There's
6226 * probably a better way to deal with this.
6228 if (!sc->sc_invalid)
6229 ath_init(sc); /* XXX lose error */
6231 ath_stop_locked(ifp);
6233 /* XXX must wakeup in places like ath_vap_delete */
6234 if (!sc->sc_invalid)
6235 ath_hal_setpower(sc->sc_ah, HAL_PM_FULL_SLEEP);
6241 error = ifmedia_ioctl(ifp, ifr, &ic->ic_media, cmd);
6244 /* NB: embed these numbers to get a consistent view */
6245 sc->sc_stats.ast_tx_packets = ifp->if_opackets;
6246 sc->sc_stats.ast_rx_packets = ifp->if_ipackets;
6247 sc->sc_stats.ast_tx_rssi = ATH_RSSI(sc->sc_halstats.ns_avgtxrssi);
6248 sc->sc_stats.ast_rx_rssi = ATH_RSSI(sc->sc_halstats.ns_avgrssi);
6249 #ifdef IEEE80211_SUPPORT_TDMA
6250 sc->sc_stats.ast_tdma_tsfadjp = TDMA_AVG(sc->sc_avgtsfdeltap);
6251 sc->sc_stats.ast_tdma_tsfadjm = TDMA_AVG(sc->sc_avgtsfdeltam);
6253 rt = sc->sc_currates;
6255 sc->sc_stats.ast_tx_rate =
6256 rt->info[sc->sc_txrix].dot11Rate &~ IEEE80211_RATE_BASIC;
6257 return copyout(&sc->sc_stats,
6258 ifr->ifr_data, sizeof (sc->sc_stats));
6260 error = priv_check(curthread, PRIV_DRIVER);
6262 memset(&sc->sc_stats, 0, sizeof(sc->sc_stats));
6266 error = ath_ioctl_diag(sc, (struct ath_diag *) ifr);
6270 error = ether_ioctl(ifp, cmd, data);
6281 ath_sysctl_slottime(SYSCTL_HANDLER_ARGS)
6283 struct ath_softc *sc = arg1;
6287 wlan_serialize_enter();
6288 slottime = ath_hal_getslottime(sc->sc_ah);
6289 error = sysctl_handle_int(oidp, &slottime, 0, req);
6290 if (error == 0 && req->newptr) {
6291 if (!ath_hal_setslottime(sc->sc_ah, slottime))
6294 wlan_serialize_exit();
6299 ath_sysctl_acktimeout(SYSCTL_HANDLER_ARGS)
6301 struct ath_softc *sc = arg1;
6305 wlan_serialize_enter();
6306 acktimeout = ath_hal_getacktimeout(sc->sc_ah);
6307 error = sysctl_handle_int(oidp, &acktimeout, 0, req);
6308 if (error == 0 && req->newptr) {
6309 if (!ath_hal_setacktimeout(sc->sc_ah, acktimeout))
6312 wlan_serialize_exit();
6317 ath_sysctl_ctstimeout(SYSCTL_HANDLER_ARGS)
6319 struct ath_softc *sc = arg1;
6323 wlan_serialize_enter();
6324 ctstimeout = ath_hal_getctstimeout(sc->sc_ah);
6325 error = sysctl_handle_int(oidp, &ctstimeout, 0, req);
6326 if (error == 0 && req->newptr) {
6327 if (!ath_hal_setctstimeout(sc->sc_ah, ctstimeout))
6330 wlan_serialize_exit();
6335 ath_sysctl_softled(SYSCTL_HANDLER_ARGS)
6337 struct ath_softc *sc = arg1;
6338 int softled = sc->sc_softled;
6341 error = sysctl_handle_int(oidp, &softled, 0, req);
6342 if (error || !req->newptr)
6344 wlan_serialize_enter();
6345 softled = (softled != 0);
6346 if (softled != sc->sc_softled) {
6348 /* NB: handle any sc_ledpin change */
6349 ath_hal_gpioCfgOutput(sc->sc_ah, sc->sc_ledpin,
6350 HAL_GPIO_MUX_MAC_NETWORK_LED);
6351 ath_hal_gpioset(sc->sc_ah, sc->sc_ledpin,
6354 sc->sc_softled = softled;
6356 wlan_serialize_exit();
6361 ath_sysctl_ledpin(SYSCTL_HANDLER_ARGS)
6363 struct ath_softc *sc = arg1;
6364 int ledpin = sc->sc_ledpin;
6367 error = sysctl_handle_int(oidp, &ledpin, 0, req);
6368 if (error || !req->newptr)
6370 wlan_serialize_enter();
6371 if (ledpin != sc->sc_ledpin) {
6372 sc->sc_ledpin = ledpin;
6373 if (sc->sc_softled) {
6374 ath_hal_gpioCfgOutput(sc->sc_ah, sc->sc_ledpin,
6375 HAL_GPIO_MUX_MAC_NETWORK_LED);
6376 ath_hal_gpioset(sc->sc_ah, sc->sc_ledpin,
6380 wlan_serialize_exit();
6385 ath_sysctl_txantenna(SYSCTL_HANDLER_ARGS)
6387 struct ath_softc *sc = arg1;
6391 wlan_serialize_enter();
6392 txantenna = ath_hal_getantennaswitch(sc->sc_ah);
6393 error = sysctl_handle_int(oidp, &txantenna, 0, req);
6395 if (!error && req->newptr) {
6396 /* XXX assumes 2 antenna ports */
6397 if (txantenna < HAL_ANT_VARIABLE ||
6398 txantenna > HAL_ANT_FIXED_B) {
6401 ath_hal_setantennaswitch(sc->sc_ah, txantenna);
6403 * NB: with the switch locked this isn't meaningful,
6404 * but set it anyway so things like radiotap get
6405 * consistent info in their data.
6407 sc->sc_txantenna = txantenna;
6410 wlan_serialize_exit();
6415 ath_sysctl_rxantenna(SYSCTL_HANDLER_ARGS)
6417 struct ath_softc *sc = arg1;
6421 wlan_serialize_enter();
6422 defantenna = ath_hal_getdefantenna(sc->sc_ah);
6423 error = sysctl_handle_int(oidp, &defantenna, 0, req);
6424 if (error == 0 && req->newptr)
6425 ath_hal_setdefantenna(sc->sc_ah, defantenna);
6426 wlan_serialize_exit();
6431 ath_sysctl_diversity(SYSCTL_HANDLER_ARGS)
6433 struct ath_softc *sc = arg1;
6437 wlan_serialize_enter();
6438 diversity = ath_hal_getdiversity(sc->sc_ah);
6439 error = sysctl_handle_int(oidp, &diversity, 0, req);
6440 if (error == 0 && req->newptr) {
6441 if (!ath_hal_setdiversity(sc->sc_ah, diversity))
6444 sc->sc_diversity = diversity;
6446 wlan_serialize_exit();
6451 ath_sysctl_diag(SYSCTL_HANDLER_ARGS)
6453 struct ath_softc *sc = arg1;
6457 wlan_serialize_enter();
6458 if (!ath_hal_getdiag(sc->sc_ah, &diag)) {
6461 error = sysctl_handle_int(oidp, &diag, 0, req);
6462 if (error == 0 && req->newptr) {
6463 if (!ath_hal_setdiag(sc->sc_ah, diag))
6467 wlan_serialize_exit();
6472 ath_sysctl_tpscale(SYSCTL_HANDLER_ARGS)
6474 struct ath_softc *sc = arg1;
6475 struct ifnet *ifp = sc->sc_ifp;
6479 wlan_serialize_enter();
6480 (void)ath_hal_gettpscale(sc->sc_ah, &scale);
6481 error = sysctl_handle_int(oidp, &scale, 0, req);
6482 if (error == 0 && req->newptr) {
6483 if (!ath_hal_settpscale(sc->sc_ah, scale))
6485 else if (ifp->if_flags & IFF_RUNNING)
6486 error = ath_reset(ifp);
6488 wlan_serialize_exit();
6493 ath_sysctl_tpc(SYSCTL_HANDLER_ARGS)
6495 struct ath_softc *sc = arg1;
6499 wlan_serialize_enter();
6500 tpc = ath_hal_gettpc(sc->sc_ah);
6501 error = sysctl_handle_int(oidp, &tpc, 0, req);
6502 if (error == 0 && req->newptr) {
6503 if (!ath_hal_settpc(sc->sc_ah, tpc))
6506 wlan_serialize_exit();
6511 ath_sysctl_rfkill(SYSCTL_HANDLER_ARGS)
6513 struct ath_softc *sc = arg1;
6519 wlan_serialize_enter();
6522 rfkill = ath_hal_getrfkill(ah);
6524 error = sysctl_handle_int(oidp, &rfkill, 0, req);
6525 if (error == 0 && req->newptr) {
6526 if (rfkill != ath_hal_getrfkill(ah)) {
6527 if (!ath_hal_setrfkill(ah, rfkill))
6529 else if (ifp->if_flags & IFF_RUNNING)
6530 error = ath_reset(ifp);
6533 wlan_serialize_exit();
6538 ath_sysctl_rfsilent(SYSCTL_HANDLER_ARGS)
6540 struct ath_softc *sc = arg1;
6544 wlan_serialize_enter();
6545 (void)ath_hal_getrfsilent(sc->sc_ah, &rfsilent);
6546 error = sysctl_handle_int(oidp, &rfsilent, 0, req);
6547 if (error == 0 && req->newptr) {
6548 if (!ath_hal_setrfsilent(sc->sc_ah, rfsilent)) {
6551 sc->sc_rfsilentpin = rfsilent & 0x1c;
6552 sc->sc_rfsilentpol = (rfsilent & 0x2) != 0;
6555 wlan_serialize_exit();
6560 ath_sysctl_tpack(SYSCTL_HANDLER_ARGS)
6562 struct ath_softc *sc = arg1;
6566 wlan_serialize_enter();
6567 (void)ath_hal_gettpack(sc->sc_ah, &tpack);
6568 error = sysctl_handle_int(oidp, &tpack, 0, req);
6569 if (error == 0 && req->newptr) {
6570 if (!ath_hal_settpack(sc->sc_ah, tpack))
6573 wlan_serialize_exit();
6578 ath_sysctl_tpcts(SYSCTL_HANDLER_ARGS)
6580 struct ath_softc *sc = arg1;
6584 wlan_serialize_enter();
6585 (void)ath_hal_gettpcts(sc->sc_ah, &tpcts);
6586 error = sysctl_handle_int(oidp, &tpcts, 0, req);
6587 if (error == 0 && req->newptr) {
6588 if (!ath_hal_settpcts(sc->sc_ah, tpcts))
6591 wlan_serialize_exit();
6596 ath_sysctl_intmit(SYSCTL_HANDLER_ARGS)
6598 struct ath_softc *sc = arg1;
6601 wlan_serialize_enter();
6602 intmit = ath_hal_getintmit(sc->sc_ah);
6603 error = sysctl_handle_int(oidp, &intmit, 0, req);
6604 if (error == 0 && req->newptr) {
6605 if (!ath_hal_setintmit(sc->sc_ah, intmit))
6608 wlan_serialize_exit();
6612 #ifdef IEEE80211_SUPPORT_TDMA
6614 ath_sysctl_setcca(SYSCTL_HANDLER_ARGS)
6616 struct ath_softc *sc = arg1;
6619 wlan_serialize_enter();
6620 setcca = sc->sc_setcca;
6621 error = sysctl_handle_int(oidp, &setcca, 0, req);
6622 if (error == 0 && req->newptr)
6623 sc->sc_setcca = (setcca != 0);
6624 wlan_serialize_exit();
6627 #endif /* IEEE80211_SUPPORT_TDMA */
6630 ath_sysctlattach(struct ath_softc *sc)
6632 struct sysctl_ctx_list *ctx;
6633 struct sysctl_oid *tree;
6634 struct ath_hal *ah = sc->sc_ah;
6636 ctx = &sc->sc_sysctl_ctx;
6637 tree = sc->sc_sysctl_tree;
6639 device_printf(sc->sc_dev, "can't add sysctl node\n");
6643 SYSCTL_ADD_INT(ctx, SYSCTL_CHILDREN(tree), OID_AUTO,
6644 "countrycode", CTLFLAG_RD, &sc->sc_eecc, 0,
6645 "EEPROM country code");
6646 SYSCTL_ADD_INT(ctx, SYSCTL_CHILDREN(tree), OID_AUTO,
6647 "regdomain", CTLFLAG_RD, &sc->sc_eerd, 0,
6648 "EEPROM regdomain code");
6650 SYSCTL_ADD_INT(ctx, SYSCTL_CHILDREN(tree), OID_AUTO,
6651 "debug", CTLFLAG_RW, &sc->sc_debug, 0,
6652 "control debugging printfs");
6654 SYSCTL_ADD_PROC(ctx, SYSCTL_CHILDREN(tree), OID_AUTO,
6655 "slottime", CTLTYPE_INT | CTLFLAG_RW, sc, 0,
6656 ath_sysctl_slottime, "I", "802.11 slot time (us)");
6657 SYSCTL_ADD_PROC(ctx, SYSCTL_CHILDREN(tree), OID_AUTO,
6658 "acktimeout", CTLTYPE_INT | CTLFLAG_RW, sc, 0,
6659 ath_sysctl_acktimeout, "I", "802.11 ACK timeout (us)");
6660 SYSCTL_ADD_PROC(ctx, SYSCTL_CHILDREN(tree), OID_AUTO,
6661 "ctstimeout", CTLTYPE_INT | CTLFLAG_RW, sc, 0,
6662 ath_sysctl_ctstimeout, "I", "802.11 CTS timeout (us)");
6663 SYSCTL_ADD_PROC(ctx, SYSCTL_CHILDREN(tree), OID_AUTO,
6664 "softled", CTLTYPE_INT | CTLFLAG_RW, sc, 0,
6665 ath_sysctl_softled, "I", "enable/disable software LED support");
6666 SYSCTL_ADD_PROC(ctx, SYSCTL_CHILDREN(tree), OID_AUTO,
6667 "ledpin", CTLTYPE_INT | CTLFLAG_RW, sc, 0,
6668 ath_sysctl_ledpin, "I", "GPIO pin connected to LED");
6669 SYSCTL_ADD_INT(ctx, SYSCTL_CHILDREN(tree), OID_AUTO,
6670 "ledon", CTLFLAG_RW, &sc->sc_ledon, 0,
6671 "setting to turn LED on");
6672 SYSCTL_ADD_INT(ctx, SYSCTL_CHILDREN(tree), OID_AUTO,
6673 "ledidle", CTLFLAG_RW, &sc->sc_ledidle, 0,
6674 "idle time for inactivity LED (ticks)");
6675 SYSCTL_ADD_PROC(ctx, SYSCTL_CHILDREN(tree), OID_AUTO,
6676 "txantenna", CTLTYPE_INT | CTLFLAG_RW, sc, 0,
6677 ath_sysctl_txantenna, "I", "antenna switch");
6678 SYSCTL_ADD_PROC(ctx, SYSCTL_CHILDREN(tree), OID_AUTO,
6679 "rxantenna", CTLTYPE_INT | CTLFLAG_RW, sc, 0,
6680 ath_sysctl_rxantenna, "I", "default/rx antenna");
6681 if (ath_hal_hasdiversity(ah))
6682 SYSCTL_ADD_PROC(ctx, SYSCTL_CHILDREN(tree), OID_AUTO,
6683 "diversity", CTLTYPE_INT | CTLFLAG_RW, sc, 0,
6684 ath_sysctl_diversity, "I", "antenna diversity");
6685 sc->sc_txintrperiod = ATH_TXINTR_PERIOD;
6686 SYSCTL_ADD_INT(ctx, SYSCTL_CHILDREN(tree), OID_AUTO,
6687 "txintrperiod", CTLFLAG_RW, &sc->sc_txintrperiod, 0,
6688 "tx descriptor batching");
6689 SYSCTL_ADD_PROC(ctx, SYSCTL_CHILDREN(tree), OID_AUTO,
6690 "diag", CTLTYPE_INT | CTLFLAG_RW, sc, 0,
6691 ath_sysctl_diag, "I", "h/w diagnostic control");
6692 SYSCTL_ADD_PROC(ctx, SYSCTL_CHILDREN(tree), OID_AUTO,
6693 "tpscale", CTLTYPE_INT | CTLFLAG_RW, sc, 0,
6694 ath_sysctl_tpscale, "I", "tx power scaling");
6695 if (ath_hal_hastpc(ah)) {
6696 SYSCTL_ADD_PROC(ctx, SYSCTL_CHILDREN(tree), OID_AUTO,
6697 "tpc", CTLTYPE_INT | CTLFLAG_RW, sc, 0,
6698 ath_sysctl_tpc, "I", "enable/disable per-packet TPC");
6699 SYSCTL_ADD_PROC(ctx, SYSCTL_CHILDREN(tree), OID_AUTO,
6700 "tpack", CTLTYPE_INT | CTLFLAG_RW, sc, 0,
6701 ath_sysctl_tpack, "I", "tx power for ack frames");
6702 SYSCTL_ADD_PROC(ctx, SYSCTL_CHILDREN(tree), OID_AUTO,
6703 "tpcts", CTLTYPE_INT | CTLFLAG_RW, sc, 0,
6704 ath_sysctl_tpcts, "I", "tx power for cts frames");
6706 if (ath_hal_hasrfsilent(ah)) {
6707 SYSCTL_ADD_PROC(ctx, SYSCTL_CHILDREN(tree), OID_AUTO,
6708 "rfsilent", CTLTYPE_INT | CTLFLAG_RW, sc, 0,
6709 ath_sysctl_rfsilent, "I", "h/w RF silent config");
6710 SYSCTL_ADD_PROC(ctx, SYSCTL_CHILDREN(tree), OID_AUTO,
6711 "rfkill", CTLTYPE_INT | CTLFLAG_RW, sc, 0,
6712 ath_sysctl_rfkill, "I", "enable/disable RF kill switch");
6714 if (ath_hal_hasintmit(ah)) {
6715 SYSCTL_ADD_PROC(ctx, SYSCTL_CHILDREN(tree), OID_AUTO,
6716 "intmit", CTLTYPE_INT | CTLFLAG_RW, sc, 0,
6717 ath_sysctl_intmit, "I", "interference mitigation");
6719 sc->sc_monpass = HAL_RXERR_DECRYPT | HAL_RXERR_MIC;
6720 SYSCTL_ADD_INT(ctx, SYSCTL_CHILDREN(tree), OID_AUTO,
6721 "monpass", CTLFLAG_RW, &sc->sc_monpass, 0,
6722 "mask of error frames to pass when monitoring");
6723 #ifdef IEEE80211_SUPPORT_TDMA
6724 if (ath_hal_macversion(ah) > 0x78) {
6725 sc->sc_tdmadbaprep = 2;
6726 SYSCTL_ADD_INT(ctx, SYSCTL_CHILDREN(tree), OID_AUTO,
6727 "dbaprep", CTLFLAG_RW, &sc->sc_tdmadbaprep, 0,
6728 "TDMA DBA preparation time");
6729 sc->sc_tdmaswbaprep = 10;
6730 SYSCTL_ADD_INT(ctx, SYSCTL_CHILDREN(tree), OID_AUTO,
6731 "swbaprep", CTLFLAG_RW, &sc->sc_tdmaswbaprep, 0,
6732 "TDMA SWBA preparation time");
6733 SYSCTL_ADD_INT(ctx, SYSCTL_CHILDREN(tree), OID_AUTO,
6734 "guardtime", CTLFLAG_RW, &sc->sc_tdmaguard, 0,
6735 "TDMA slot guard time");
6736 SYSCTL_ADD_INT(ctx, SYSCTL_CHILDREN(tree), OID_AUTO,
6737 "superframe", CTLFLAG_RD, &sc->sc_tdmabintval, 0,
6738 "TDMA calculated super frame");
6739 SYSCTL_ADD_PROC(ctx, SYSCTL_CHILDREN(tree), OID_AUTO,
6740 "setcca", CTLTYPE_INT | CTLFLAG_RW, sc, 0,
6741 ath_sysctl_setcca, "I", "enable CCA control");
6747 ath_tx_raw_start(struct ath_softc *sc, struct ieee80211_node *ni,
6748 struct ath_buf *bf, struct mbuf *m0,
6749 const struct ieee80211_bpf_params *params)
6751 struct ifnet *ifp = sc->sc_ifp;
6752 struct ieee80211com *ic = ifp->if_l2com;
6753 struct ath_hal *ah = sc->sc_ah;
6754 struct ieee80211vap *vap = ni->ni_vap;
6755 int error, ismcast, ismrr;
6756 int keyix, hdrlen, pktlen, try0, txantenna;
6757 u_int8_t rix, cix, txrate, ctsrate, rate1, rate2, rate3;
6758 struct ieee80211_frame *wh;
6759 u_int flags, ctsduration;
6761 const HAL_RATE_TABLE *rt;
6762 struct ath_desc *ds;
6765 wh = mtod(m0, struct ieee80211_frame *);
6766 ismcast = IEEE80211_IS_MULTICAST(wh->i_addr1);
6767 hdrlen = ieee80211_anyhdrsize(wh);
6769 * Packet length must not include any
6770 * pad bytes; deduct them here.
6772 /* XXX honor IEEE80211_BPF_DATAPAD */
6773 pktlen = m0->m_pkthdr.len - (hdrlen & 3) + IEEE80211_CRC_LEN;
6775 if (params->ibp_flags & IEEE80211_BPF_CRYPTO) {
6776 const struct ieee80211_cipher *cip;
6777 struct ieee80211_key *k;
6780 * Construct the 802.11 header+trailer for an encrypted
6781 * frame. The only reason this can fail is because of an
6782 * unknown or unsupported cipher/key type.
6784 k = ieee80211_crypto_encap(ni, m0);
6787 * This can happen when the key is yanked after the
6788 * frame was queued. Just discard the frame; the
6789 * 802.11 layer counts failures and provides
6790 * debugging/diagnostics.
6796 * Adjust the packet + header lengths for the crypto
6797 * additions and calculate the h/w key index. When
6798 * a s/w mic is done the frame will have had any mic
6799 * added to it prior to entry so m0->m_pkthdr.len will
6800 * account for it. Otherwise we need to add it to the
6804 hdrlen += cip->ic_header;
6805 pktlen += cip->ic_header + cip->ic_trailer;
6806 /* NB: frags always have any TKIP MIC done in s/w */
6807 if ((k->wk_flags & IEEE80211_KEY_SWMIC) == 0)
6808 pktlen += cip->ic_miclen;
6809 keyix = k->wk_keyix;
6811 /* packet header may have moved, reset our local pointer */
6812 wh = mtod(m0, struct ieee80211_frame *);
6813 } else if (ni->ni_ucastkey.wk_cipher == &ieee80211_cipher_none) {
6815 * Use station key cache slot, if assigned.
6817 keyix = ni->ni_ucastkey.wk_keyix;
6818 if (keyix == IEEE80211_KEYIX_NONE)
6819 keyix = HAL_TXKEYIX_INVALID;
6821 keyix = HAL_TXKEYIX_INVALID;
6823 error = ath_tx_dmasetup(sc, bf, m0);
6826 m0 = bf->bf_m; /* NB: may have changed */
6827 wh = mtod(m0, struct ieee80211_frame *);
6828 bf->bf_node = ni; /* NB: held reference */
6830 flags = HAL_TXDESC_CLRDMASK; /* XXX needed for crypto errs */
6831 flags |= HAL_TXDESC_INTREQ; /* force interrupt */
6832 if (params->ibp_flags & IEEE80211_BPF_RTS)
6833 flags |= HAL_TXDESC_RTSENA;
6834 else if (params->ibp_flags & IEEE80211_BPF_CTS)
6835 flags |= HAL_TXDESC_CTSENA;
6836 /* XXX leave ismcast to injector? */
6837 if ((params->ibp_flags & IEEE80211_BPF_NOACK) || ismcast)
6838 flags |= HAL_TXDESC_NOACK;
6840 rt = sc->sc_currates;
6841 KASSERT(rt != NULL, ("no rate table, mode %u", sc->sc_curmode));
6842 rix = ath_tx_findrix(sc, params->ibp_rate0);
6843 txrate = rt->info[rix].rateCode;
6844 if (params->ibp_flags & IEEE80211_BPF_SHORTPRE)
6845 txrate |= rt->info[rix].shortPreamble;
6847 try0 = params->ibp_try0;
6848 ismrr = (params->ibp_try1 != 0);
6849 txantenna = params->ibp_pri >> 2;
6850 if (txantenna == 0) /* XXX? */
6851 txantenna = sc->sc_txantenna;
6853 if (flags & (HAL_TXDESC_CTSENA | HAL_TXDESC_RTSENA)) {
6854 cix = ath_tx_findrix(sc, params->ibp_ctsrate);
6855 ctsrate = rt->info[cix].rateCode;
6856 if (params->ibp_flags & IEEE80211_BPF_SHORTPRE) {
6857 ctsrate |= rt->info[cix].shortPreamble;
6858 if (flags & HAL_TXDESC_RTSENA) /* SIFS + CTS */
6859 ctsduration += rt->info[cix].spAckDuration;
6860 ctsduration += ath_hal_computetxtime(ah,
6861 rt, pktlen, rix, AH_TRUE);
6862 if ((flags & HAL_TXDESC_NOACK) == 0) /* SIFS + ACK */
6863 ctsduration += rt->info[rix].spAckDuration;
6865 if (flags & HAL_TXDESC_RTSENA) /* SIFS + CTS */
6866 ctsduration += rt->info[cix].lpAckDuration;
6867 ctsduration += ath_hal_computetxtime(ah,
6868 rt, pktlen, rix, AH_FALSE);
6869 if ((flags & HAL_TXDESC_NOACK) == 0) /* SIFS + ACK */
6870 ctsduration += rt->info[rix].lpAckDuration;
6872 ismrr = 0; /* XXX */
6875 pri = params->ibp_pri & 3;
6877 * NB: we mark all packets as type PSPOLL so the h/w won't
6878 * set the sequence number, duration, etc.
6880 atype = HAL_PKT_TYPE_PSPOLL;
6882 if (IFF_DUMPPKTS(sc, ATH_DEBUG_XMIT))
6883 ieee80211_dump_pkt(ic, mtod(m0, caddr_t), m0->m_len,
6884 sc->sc_hwmap[rix].ieeerate, -1);
6886 if (ieee80211_radiotap_active_vap(vap)) {
6887 u_int64_t tsf = ath_hal_gettsf64(ah);
6889 sc->sc_tx_th.wt_tsf = htole64(tsf);
6890 sc->sc_tx_th.wt_flags = sc->sc_hwmap[rix].txflags;
6891 if (wh->i_fc[1] & IEEE80211_FC1_WEP)
6892 sc->sc_tx_th.wt_flags |= IEEE80211_RADIOTAP_F_WEP;
6893 if (m0->m_flags & M_FRAG)
6894 sc->sc_tx_th.wt_flags |= IEEE80211_RADIOTAP_F_FRAG;
6895 sc->sc_tx_th.wt_rate = sc->sc_hwmap[rix].ieeerate;
6896 sc->sc_tx_th.wt_txpower = ni->ni_txpower;
6897 sc->sc_tx_th.wt_antenna = sc->sc_txantenna;
6899 ieee80211_radiotap_tx(vap, m0);
6903 * Formulate first tx descriptor with tx controls.
6906 /* XXX check return value? */
6907 ath_hal_setuptxdesc(ah, ds
6908 , pktlen /* packet length */
6909 , hdrlen /* header length */
6910 , atype /* Atheros packet type */
6911 , params->ibp_power /* txpower */
6912 , txrate, try0 /* series 0 rate/tries */
6913 , keyix /* key cache index */
6914 , txantenna /* antenna mode */
6916 , ctsrate /* rts/cts rate */
6917 , ctsduration /* rts/cts duration */
6919 bf->bf_txflags = flags;
6922 rix = ath_tx_findrix(sc, params->ibp_rate1);
6923 rate1 = rt->info[rix].rateCode;
6924 if (params->ibp_flags & IEEE80211_BPF_SHORTPRE)
6925 rate1 |= rt->info[rix].shortPreamble;
6926 if (params->ibp_try2) {
6927 rix = ath_tx_findrix(sc, params->ibp_rate2);
6928 rate2 = rt->info[rix].rateCode;
6929 if (params->ibp_flags & IEEE80211_BPF_SHORTPRE)
6930 rate2 |= rt->info[rix].shortPreamble;
6933 if (params->ibp_try3) {
6934 rix = ath_tx_findrix(sc, params->ibp_rate3);
6935 rate3 = rt->info[rix].rateCode;
6936 if (params->ibp_flags & IEEE80211_BPF_SHORTPRE)
6937 rate3 |= rt->info[rix].shortPreamble;
6940 ath_hal_setupxtxdesc(ah, ds
6941 , rate1, params->ibp_try1 /* series 1 */
6942 , rate2, params->ibp_try2 /* series 2 */
6943 , rate3, params->ibp_try3 /* series 3 */
6947 /* NB: no buffered multicast in power save support */
6948 ath_tx_handoff(sc, sc->sc_ac2q[pri], bf);
6953 ath_raw_xmit(struct ieee80211_node *ni, struct mbuf *m,
6954 const struct ieee80211_bpf_params *params)
6956 struct ieee80211com *ic = ni->ni_ic;
6957 struct ifnet *ifp = ic->ic_ifp;
6958 struct ath_softc *sc = ifp->if_softc;
6962 if ((ifp->if_flags & IFF_RUNNING) == 0 || sc->sc_invalid) {
6963 DPRINTF(sc, ATH_DEBUG_XMIT, "%s: discard frame, %s", __func__,
6964 (ifp->if_flags & IFF_RUNNING) == 0 ?
6965 "!running" : "invalid");
6971 * Grab a TX buffer and associated resources.
6973 bf = ath_getbuf(sc);
6975 sc->sc_stats.ast_tx_nobuf++;
6981 if (params == NULL) {
6983 * Legacy path; interpret frame contents to decide
6984 * precisely how to send the frame.
6986 if (ath_tx_start(sc, ni, bf, m)) {
6987 error = EIO; /* XXX */
6992 * Caller supplied explicit parameters to use in
6993 * sending the frame.
6995 if (ath_tx_raw_start(sc, ni, bf, m, params)) {
6996 error = EIO; /* XXX */
7000 sc->sc_wd_timer = 5;
7002 sc->sc_stats.ast_tx_raw++;
7006 STAILQ_INSERT_HEAD(&sc->sc_txbuf, bf, bf_list);
7009 sc->sc_stats.ast_tx_raw_fail++;
7010 ieee80211_free_node(ni);
7015 * Announce various information on device/driver attach.
7018 ath_announce(struct ath_softc *sc)
7020 struct ifnet *ifp = sc->sc_ifp;
7021 struct ath_hal *ah = sc->sc_ah;
7023 if_printf(ifp, "AR%s mac %d.%d RF%s phy %d.%d\n",
7024 ath_hal_mac_name(ah), ah->ah_macVersion, ah->ah_macRev,
7025 ath_hal_rf_name(ah), ah->ah_phyRev >> 4, ah->ah_phyRev & 0xf);
7028 for (i = 0; i <= WME_AC_VO; i++) {
7029 struct ath_txq *txq = sc->sc_ac2q[i];
7030 if_printf(ifp, "Use hw queue %u for %s traffic\n",
7031 txq->axq_qnum, ieee80211_wme_acnames[i]);
7033 if_printf(ifp, "Use hw queue %u for CAB traffic\n",
7034 sc->sc_cabq->axq_qnum);
7035 if_printf(ifp, "Use hw queue %u for beacons\n", sc->sc_bhalq);
7037 if (ath_rxbuf != ATH_RXBUF)
7038 if_printf(ifp, "using %u rx buffers\n", ath_rxbuf);
7039 if (ath_txbuf != ATH_TXBUF)
7040 if_printf(ifp, "using %u tx buffers\n", ath_txbuf);
7041 if (sc->sc_mcastkey && bootverbose)
7042 if_printf(ifp, "using multicast key search\n");
7045 #ifdef IEEE80211_SUPPORT_TDMA
7046 static __inline uint32_t
7047 ath_hal_getnexttbtt(struct ath_hal *ah)
7049 #define AR_TIMER0 0x8028
7050 return OS_REG_READ(ah, AR_TIMER0);
7053 static __inline void
7054 ath_hal_adjusttsf(struct ath_hal *ah, int32_t tsfdelta)
7056 /* XXX handle wrap/overflow */
7057 OS_REG_WRITE(ah, AR_TSF_L32, OS_REG_READ(ah, AR_TSF_L32) + tsfdelta);
7061 ath_tdma_settimers(struct ath_softc *sc, u_int32_t nexttbtt, u_int32_t bintval)
7063 struct ath_hal *ah = sc->sc_ah;
7064 HAL_BEACON_TIMERS bt;
7066 bt.bt_intval = bintval | HAL_BEACON_ENA;
7067 bt.bt_nexttbtt = nexttbtt;
7068 bt.bt_nextdba = (nexttbtt<<3) - sc->sc_tdmadbaprep;
7069 bt.bt_nextswba = (nexttbtt<<3) - sc->sc_tdmaswbaprep;
7070 bt.bt_nextatim = nexttbtt+1;
7071 ath_hal_beaconsettimers(ah, &bt);
7075 * Calculate the beacon interval. This is periodic in the
7076 * superframe for the bss. We assume each station is configured
7077 * identically wrt transmit rate so the guard time we calculate
7078 * above will be the same on all stations. Note we need to
7079 * factor in the xmit time because the hardware will schedule
7080 * a frame for transmit if the start of the frame is within
7081 * the burst time. When we get hardware that properly kills
7082 * frames in the PCU we can reduce/eliminate the guard time.
7084 * Roundup to 1024 is so we have 1 TU buffer in the guard time
7085 * to deal with the granularity of the nexttbtt timer. 11n MAC's
7086 * with 1us timer granularity should allow us to reduce/eliminate
7090 ath_tdma_bintvalsetup(struct ath_softc *sc,
7091 const struct ieee80211_tdma_state *tdma)
7093 /* copy from vap state (XXX check all vaps have same value?) */
7094 sc->sc_tdmaslotlen = tdma->tdma_slotlen;
7096 sc->sc_tdmabintval = roundup((sc->sc_tdmaslotlen+sc->sc_tdmaguard) *
7097 tdma->tdma_slotcnt, 1024);
7098 sc->sc_tdmabintval >>= 10; /* TSF -> TU */
7099 if (sc->sc_tdmabintval & 1)
7100 sc->sc_tdmabintval++;
7102 if (tdma->tdma_slot == 0) {
7104 * Only slot 0 beacons; other slots respond.
7106 sc->sc_imask |= HAL_INT_SWBA;
7107 sc->sc_tdmaswba = 0; /* beacon immediately */
7109 /* XXX all vaps must be slot 0 or slot !0 */
7110 sc->sc_imask &= ~HAL_INT_SWBA;
7115 * Max 802.11 overhead. This assumes no 4-address frames and
7116 * the encapsulation done by ieee80211_encap (llc). We also
7117 * include potential crypto overhead.
7119 #define IEEE80211_MAXOVERHEAD \
7120 (sizeof(struct ieee80211_qosframe) \
7121 + sizeof(struct llc) \
7122 + IEEE80211_ADDR_LEN \
7123 + IEEE80211_WEP_IVLEN \
7124 + IEEE80211_WEP_KIDLEN \
7125 + IEEE80211_WEP_CRCLEN \
7126 + IEEE80211_WEP_MICLEN \
7127 + IEEE80211_CRC_LEN)
7130 * Setup initially for tdma operation. Start the beacon
7131 * timers and enable SWBA if we are slot 0. Otherwise
7132 * we wait for slot 0 to arrive so we can sync up before
7133 * starting to transmit.
7136 ath_tdma_config(struct ath_softc *sc, struct ieee80211vap *vap)
7138 struct ath_hal *ah = sc->sc_ah;
7139 struct ifnet *ifp = sc->sc_ifp;
7140 struct ieee80211com *ic = ifp->if_l2com;
7141 const struct ieee80211_txparam *tp;
7142 const struct ieee80211_tdma_state *tdma = NULL;
7146 vap = TAILQ_FIRST(&ic->ic_vaps); /* XXX */
7148 if_printf(ifp, "%s: no vaps?\n", __func__);
7152 tp = vap->iv_bss->ni_txparms;
7154 * Calculate the guard time for each slot. This is the
7155 * time to send a maximal-size frame according to the
7156 * fixed/lowest transmit rate. Note that the interface
7157 * mtu does not include the 802.11 overhead so we must
7158 * tack that on (ath_hal_computetxtime includes the
7159 * preamble and plcp in it's calculation).
7161 tdma = vap->iv_tdma;
7162 if (tp->ucastrate != IEEE80211_FIXED_RATE_NONE)
7163 rix = ath_tx_findrix(sc, tp->ucastrate);
7165 rix = ath_tx_findrix(sc, tp->mcastrate);
7166 /* XXX short preamble assumed */
7167 sc->sc_tdmaguard = ath_hal_computetxtime(ah, sc->sc_currates,
7168 ifp->if_mtu + IEEE80211_MAXOVERHEAD, rix, AH_TRUE);
7170 ath_hal_intrset(ah, 0);
7172 ath_beaconq_config(sc); /* setup h/w beacon q */
7174 ath_hal_setcca(ah, AH_FALSE); /* disable CCA */
7175 ath_tdma_bintvalsetup(sc, tdma); /* calculate beacon interval */
7176 ath_tdma_settimers(sc, sc->sc_tdmabintval,
7177 sc->sc_tdmabintval | HAL_BEACON_RESET_TSF);
7178 sc->sc_syncbeacon = 0;
7180 sc->sc_avgtsfdeltap = TDMA_DUMMY_MARKER;
7181 sc->sc_avgtsfdeltam = TDMA_DUMMY_MARKER;
7183 ath_hal_intrset(ah, sc->sc_imask);
7185 DPRINTF(sc, ATH_DEBUG_TDMA, "%s: slot %u len %uus cnt %u "
7186 "bsched %u guard %uus bintval %u TU dba prep %u\n", __func__,
7187 tdma->tdma_slot, tdma->tdma_slotlen, tdma->tdma_slotcnt,
7188 tdma->tdma_bintval, sc->sc_tdmaguard, sc->sc_tdmabintval,
7189 sc->sc_tdmadbaprep);
7193 * Update tdma operation. Called from the 802.11 layer
7194 * when a beacon is received from the TDMA station operating
7195 * in the slot immediately preceding us in the bss. Use
7196 * the rx timestamp for the beacon frame to update our
7197 * beacon timers so we follow their schedule. Note that
7198 * by using the rx timestamp we implicitly include the
7199 * propagation delay in our schedule.
7202 ath_tdma_update(struct ieee80211_node *ni,
7203 const struct ieee80211_tdma_param *tdma, int changed)
7205 #define TSF_TO_TU(_h,_l) \
7206 ((((u_int32_t)(_h)) << 22) | (((u_int32_t)(_l)) >> 10))
7207 #define TU_TO_TSF(_tu) (((u_int64_t)(_tu)) << 10)
7208 struct ieee80211vap *vap = ni->ni_vap;
7209 struct ieee80211com *ic = ni->ni_ic;
7210 struct ath_softc *sc = ic->ic_ifp->if_softc;
7211 struct ath_hal *ah = sc->sc_ah;
7212 const HAL_RATE_TABLE *rt = sc->sc_currates;
7213 u_int64_t tsf, rstamp, nextslot;
7214 u_int32_t txtime, nextslottu, timer0;
7215 int32_t tudelta, tsfdelta;
7216 const struct ath_rx_status *rs;
7219 sc->sc_stats.ast_tdma_update++;
7222 * Check for and adopt configuration changes.
7225 const struct ieee80211_tdma_state *ts = vap->iv_tdma;
7227 ath_tdma_bintvalsetup(sc, ts);
7228 if (changed & TDMA_UPDATE_SLOTLEN)
7231 DPRINTF(sc, ATH_DEBUG_TDMA,
7232 "%s: adopt slot %u slotcnt %u slotlen %u us "
7233 "bintval %u TU\n", __func__,
7234 ts->tdma_slot, ts->tdma_slotcnt, ts->tdma_slotlen,
7235 sc->sc_tdmabintval);
7238 ath_hal_intrset(ah, sc->sc_imask);
7239 /* NB: beacon timers programmed below */
7242 /* extend rx timestamp to 64 bits */
7244 tsf = ath_hal_gettsf64(ah);
7245 rstamp = ath_extend_tsf(rs->rs_tstamp, tsf);
7247 * The rx timestamp is set by the hardware on completing
7248 * reception (at the point where the rx descriptor is DMA'd
7249 * to the host). To find the start of our next slot we
7250 * must adjust this time by the time required to send
7251 * the packet just received.
7253 rix = rt->rateCodeToIndex[rs->rs_rate];
7254 txtime = ath_hal_computetxtime(ah, rt, rs->rs_datalen, rix,
7255 rt->info[rix].shortPreamble);
7256 /* NB: << 9 is to cvt to TU and /2 */
7257 nextslot = (rstamp - txtime) + (sc->sc_tdmabintval << 9);
7258 nextslottu = TSF_TO_TU(nextslot>>32, nextslot) & HAL_BEACON_PERIOD;
7261 * TIMER0 is the h/w's idea of NextTBTT (in TU's). Convert
7262 * to usecs and calculate the difference between what the
7263 * other station thinks and what we have programmed. This
7264 * lets us figure how to adjust our timers to match. The
7265 * adjustments are done by pulling the TSF forward and possibly
7266 * rewriting the beacon timers.
7268 timer0 = ath_hal_getnexttbtt(ah);
7269 tsfdelta = (int32_t)((nextslot % TU_TO_TSF(HAL_BEACON_PERIOD+1)) - TU_TO_TSF(timer0));
7271 DPRINTF(sc, ATH_DEBUG_TDMA_TIMER,
7272 "tsfdelta %d avg +%d/-%d\n", tsfdelta,
7273 TDMA_AVG(sc->sc_avgtsfdeltap), TDMA_AVG(sc->sc_avgtsfdeltam));
7276 TDMA_SAMPLE(sc->sc_avgtsfdeltap, 0);
7277 TDMA_SAMPLE(sc->sc_avgtsfdeltam, -tsfdelta);
7278 tsfdelta = -tsfdelta % 1024;
7280 } else if (tsfdelta > 0) {
7281 TDMA_SAMPLE(sc->sc_avgtsfdeltap, tsfdelta);
7282 TDMA_SAMPLE(sc->sc_avgtsfdeltam, 0);
7283 tsfdelta = 1024 - (tsfdelta % 1024);
7286 TDMA_SAMPLE(sc->sc_avgtsfdeltap, 0);
7287 TDMA_SAMPLE(sc->sc_avgtsfdeltam, 0);
7289 tudelta = nextslottu - timer0;
7292 * Copy sender's timetstamp into tdma ie so they can
7293 * calculate roundtrip time. We submit a beacon frame
7294 * below after any timer adjustment. The frame goes out
7295 * at the next TBTT so the sender can calculate the
7296 * roundtrip by inspecting the tdma ie in our beacon frame.
7298 * NB: This tstamp is subtlely preserved when
7299 * IEEE80211_BEACON_TDMA is marked (e.g. when the
7300 * slot position changes) because ieee80211_add_tdma
7301 * skips over the data.
7303 memcpy(ATH_VAP(vap)->av_boff.bo_tdma +
7304 __offsetof(struct ieee80211_tdma_param, tdma_tstamp),
7305 &ni->ni_tstamp.data, 8);
7307 DPRINTF(sc, ATH_DEBUG_TDMA_TIMER,
7308 "tsf %llu nextslot %llu (%d, %d) nextslottu %u timer0 %u (%d)\n",
7309 (unsigned long long) tsf, (unsigned long long) nextslot,
7310 (int)(nextslot - tsf), tsfdelta,
7311 nextslottu, timer0, tudelta);
7314 * Adjust the beacon timers only when pulling them forward
7315 * or when going back by less than the beacon interval.
7316 * Negative jumps larger than the beacon interval seem to
7317 * cause the timers to stop and generally cause instability.
7318 * This basically filters out jumps due to missed beacons.
7320 if (tudelta != 0 && (tudelta > 0 || -tudelta < sc->sc_tdmabintval)) {
7321 ath_tdma_settimers(sc, nextslottu, sc->sc_tdmabintval);
7322 sc->sc_stats.ast_tdma_timers++;
7325 ath_hal_adjusttsf(ah, tsfdelta);
7326 sc->sc_stats.ast_tdma_tsf++;
7328 ath_tdma_beacon_send(sc, vap); /* prepare response */
7334 * Transmit a beacon frame at SWBA. Dynamic updates
7335 * to the frame contents are done as needed.
7338 ath_tdma_beacon_send(struct ath_softc *sc, struct ieee80211vap *vap)
7340 struct ath_hal *ah = sc->sc_ah;
7345 * Check if the previous beacon has gone out. If
7346 * not don't try to post another, skip this period
7347 * and wait for the next. Missed beacons indicate
7348 * a problem and should not occur. If we miss too
7349 * many consecutive beacons reset the device.
7351 if (ath_hal_numtxpending(ah, sc->sc_bhalq) != 0) {
7352 sc->sc_bmisscount++;
7353 DPRINTF(sc, ATH_DEBUG_BEACON,
7354 "%s: missed %u consecutive beacons\n",
7355 __func__, sc->sc_bmisscount);
7356 if (sc->sc_bmisscount >= ath_bstuck_threshold)
7357 taskqueue_enqueue(sc->sc_tq, &sc->sc_bstucktask);
7360 if (sc->sc_bmisscount != 0) {
7361 DPRINTF(sc, ATH_DEBUG_BEACON,
7362 "%s: resume beacon xmit after %u misses\n",
7363 __func__, sc->sc_bmisscount);
7364 sc->sc_bmisscount = 0;
7368 * Check recent per-antenna transmit statistics and flip
7369 * the default antenna if noticeably more frames went out
7370 * on the non-default antenna.
7371 * XXX assumes 2 anntenae
7373 if (!sc->sc_diversity) {
7374 otherant = sc->sc_defant & 1 ? 2 : 1;
7375 if (sc->sc_ant_tx[otherant] > sc->sc_ant_tx[sc->sc_defant] + 2)
7376 ath_setdefantenna(sc, otherant);
7377 sc->sc_ant_tx[1] = sc->sc_ant_tx[2] = 0;
7381 * Stop any current dma before messing with the beacon linkages.
7383 * This should never fail since we check above that no frames
7384 * are still pending on the queue.
7386 if (!ath_hal_stoptxdma(ah, sc->sc_bhalq)) {
7387 DPRINTF(sc, ATH_DEBUG_ANY,
7388 "%s: beacon queue %u did not stop?\n",
7389 __func__, sc->sc_bhalq);
7390 /* NB: the HAL still stops DMA, so proceed */
7392 bf = ath_beacon_generate(sc, vap);
7394 ath_hal_puttxbuf(ah, sc->sc_bhalq, bf->bf_daddr);
7395 ath_hal_txstart(ah, sc->sc_bhalq);
7397 sc->sc_stats.ast_be_xmit++; /* XXX per-vap? */
7400 * Record local TSF for our last send for use
7401 * in arbitrating slot collisions.
7403 vap->iv_bss->ni_tstamp.tsf = ath_hal_gettsf64(ah);
7405 device_printf(sc->sc_dev, "tdma beacon gen failed!\n");
7408 #endif /* IEEE80211_SUPPORT_TDMA */
7411 ath_sysctl_clearstats(SYSCTL_HANDLER_ARGS)
7413 struct ath_softc *sc = arg1;
7417 error = sysctl_handle_int(oidp, &val, 0, req);
7418 if (error || !req->newptr)
7421 return 0; /* Not clearing the stats is still valid */
7422 memset(&sc->sc_stats, 0, sizeof(sc->sc_stats));
7428 ath_sysctl_stats_attach(struct ath_softc *sc)
7430 struct sysctl_oid *tree;
7431 struct sysctl_ctx_list *ctx;
7432 struct sysctl_oid_list *child;
7434 ctx = &sc->sc_sysctl_ctx;
7435 tree = sc->sc_sysctl_tree;
7436 child = SYSCTL_CHILDREN(tree);
7438 /* Create "clear" node */
7439 SYSCTL_ADD_PROC(ctx, SYSCTL_CHILDREN(tree), OID_AUTO,
7440 "clear_stats", CTLTYPE_INT | CTLFLAG_RW, sc, 0,
7441 ath_sysctl_clearstats, "I", "clear stats");
7443 /* Create stats node */
7444 tree = SYSCTL_ADD_NODE(ctx, child, OID_AUTO, "stats", CTLFLAG_RD,
7445 NULL, "Statistics");
7446 child = SYSCTL_CHILDREN(tree);
7448 /* This was generated from if_athioctl.h */
7450 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_watchdog", CTLFLAG_RD,
7451 &sc->sc_stats.ast_watchdog, 0, "device reset by watchdog");
7452 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_hardware", CTLFLAG_RD,
7453 &sc->sc_stats.ast_hardware, 0, "fatal hardware error interrupts");
7454 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_bmiss", CTLFLAG_RD,
7455 &sc->sc_stats.ast_bmiss, 0, "beacon miss interrupts");
7456 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_bmiss_phantom", CTLFLAG_RD,
7457 &sc->sc_stats.ast_bmiss_phantom, 0, "beacon miss interrupts");
7458 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_bstuck", CTLFLAG_RD,
7459 &sc->sc_stats.ast_bstuck, 0, "beacon stuck interrupts");
7460 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_rxorn", CTLFLAG_RD,
7461 &sc->sc_stats.ast_rxorn, 0, "rx overrun interrupts");
7462 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_rxeol", CTLFLAG_RD,
7463 &sc->sc_stats.ast_rxeol, 0, "rx eol interrupts");
7464 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_txurn", CTLFLAG_RD,
7465 &sc->sc_stats.ast_txurn, 0, "tx underrun interrupts");
7466 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_mib", CTLFLAG_RD,
7467 &sc->sc_stats.ast_mib, 0, "mib interrupts");
7468 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_intrcoal", CTLFLAG_RD,
7469 &sc->sc_stats.ast_intrcoal, 0, "interrupts coalesced");
7470 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_tx_packets", CTLFLAG_RD,
7471 &sc->sc_stats.ast_tx_packets, 0, "packet sent on the interface");
7472 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_tx_mgmt", CTLFLAG_RD,
7473 &sc->sc_stats.ast_tx_mgmt, 0, "management frames transmitted");
7474 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_tx_discard", CTLFLAG_RD,
7475 &sc->sc_stats.ast_tx_discard, 0, "frames discarded prior to assoc");
7476 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_tx_qstop", CTLFLAG_RD,
7477 &sc->sc_stats.ast_tx_qstop, 0, "output stopped 'cuz no buffer");
7478 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_tx_encap", CTLFLAG_RD,
7479 &sc->sc_stats.ast_tx_encap, 0, "tx encapsulation failed");
7480 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_tx_nonode", CTLFLAG_RD,
7481 &sc->sc_stats.ast_tx_nonode, 0, "tx failed 'cuz no node");
7482 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_tx_nombuf", CTLFLAG_RD,
7483 &sc->sc_stats.ast_tx_nombuf, 0, "tx failed 'cuz no mbuf");
7484 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_tx_nomcl", CTLFLAG_RD,
7485 &sc->sc_stats.ast_tx_nomcl, 0, "tx failed 'cuz no cluster");
7486 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_tx_linear", CTLFLAG_RD,
7487 &sc->sc_stats.ast_tx_linear, 0, "tx linearized to cluster");
7488 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_tx_nodata", CTLFLAG_RD,
7489 &sc->sc_stats.ast_tx_nodata, 0, "tx discarded empty frame");
7490 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_tx_busdma", CTLFLAG_RD,
7491 &sc->sc_stats.ast_tx_busdma, 0, "tx failed for dma resrcs");
7492 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_tx_xretries", CTLFLAG_RD,
7493 &sc->sc_stats.ast_tx_xretries, 0, "tx failed 'cuz too many retries");
7494 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_tx_fifoerr", CTLFLAG_RD,
7495 &sc->sc_stats.ast_tx_fifoerr, 0, "tx failed 'cuz FIFO underrun");
7496 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_tx_filtered", CTLFLAG_RD,
7497 &sc->sc_stats.ast_tx_filtered, 0, "tx failed 'cuz xmit filtered");
7498 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_tx_shortretry", CTLFLAG_RD,
7499 &sc->sc_stats.ast_tx_shortretry, 0, "tx on-chip retries (short)");
7500 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_tx_longretry", CTLFLAG_RD,
7501 &sc->sc_stats.ast_tx_longretry, 0, "tx on-chip retries (long)");
7502 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_tx_badrate", CTLFLAG_RD,
7503 &sc->sc_stats.ast_tx_badrate, 0, "tx failed 'cuz bogus xmit rate");
7504 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_tx_noack", CTLFLAG_RD,
7505 &sc->sc_stats.ast_tx_noack, 0, "tx frames with no ack marked");
7506 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_tx_rts", CTLFLAG_RD,
7507 &sc->sc_stats.ast_tx_rts, 0, "tx frames with rts enabled");
7508 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_tx_cts", CTLFLAG_RD,
7509 &sc->sc_stats.ast_tx_cts, 0, "tx frames with cts enabled");
7510 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_tx_shortpre", CTLFLAG_RD,
7511 &sc->sc_stats.ast_tx_shortpre, 0, "tx frames with short preamble");
7512 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_tx_altrate", CTLFLAG_RD,
7513 &sc->sc_stats.ast_tx_altrate, 0, "tx frames with alternate rate");
7514 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_tx_protect", CTLFLAG_RD,
7515 &sc->sc_stats.ast_tx_protect, 0, "tx frames with protection");
7516 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_tx_ctsburst", CTLFLAG_RD,
7517 &sc->sc_stats.ast_tx_ctsburst, 0, "tx frames with cts and bursting");
7518 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_tx_ctsext", CTLFLAG_RD,
7519 &sc->sc_stats.ast_tx_ctsext, 0, "tx frames with cts extension");
7520 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_rx_nombuf", CTLFLAG_RD,
7521 &sc->sc_stats.ast_rx_nombuf, 0, "rx setup failed 'cuz no mbuf");
7522 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_rx_busdma", CTLFLAG_RD,
7523 &sc->sc_stats.ast_rx_busdma, 0, "rx setup failed for dma resrcs");
7524 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_rx_orn", CTLFLAG_RD,
7525 &sc->sc_stats.ast_rx_orn, 0, "rx failed 'cuz of desc overrun");
7526 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_rx_crcerr", CTLFLAG_RD,
7527 &sc->sc_stats.ast_rx_crcerr, 0, "rx failed 'cuz of bad CRC");
7528 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_rx_fifoerr", CTLFLAG_RD,
7529 &sc->sc_stats.ast_rx_fifoerr, 0, "rx failed 'cuz of FIFO overrun");
7530 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_rx_badcrypt", CTLFLAG_RD,
7531 &sc->sc_stats.ast_rx_badcrypt, 0, "rx failed 'cuz decryption");
7532 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_rx_badmic", CTLFLAG_RD,
7533 &sc->sc_stats.ast_rx_badmic, 0, "rx failed 'cuz MIC failure");
7534 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_rx_phyerr", CTLFLAG_RD,
7535 &sc->sc_stats.ast_rx_phyerr, 0, "rx failed 'cuz of PHY err");
7536 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_rx_tooshort", CTLFLAG_RD,
7537 &sc->sc_stats.ast_rx_tooshort, 0, "rx discarded 'cuz frame too short");
7538 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_rx_toobig", CTLFLAG_RD,
7539 &sc->sc_stats.ast_rx_toobig, 0, "rx discarded 'cuz frame too large");
7540 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_rx_packets", CTLFLAG_RD,
7541 &sc->sc_stats.ast_rx_packets, 0, "packet recv on the interface");
7542 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_rx_mgt", CTLFLAG_RD,
7543 &sc->sc_stats.ast_rx_mgt, 0, "management frames received");
7544 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_rx_ctl", CTLFLAG_RD,
7545 &sc->sc_stats.ast_rx_ctl, 0, "rx discarded 'cuz ctl frame");
7546 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_be_xmit", CTLFLAG_RD,
7547 &sc->sc_stats.ast_be_xmit, 0, "beacons transmitted");
7548 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_be_nombuf", CTLFLAG_RD,
7549 &sc->sc_stats.ast_be_nombuf, 0, "beacon setup failed 'cuz no mbuf");
7550 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_per_cal", CTLFLAG_RD,
7551 &sc->sc_stats.ast_per_cal, 0, "periodic calibration calls");
7552 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_per_calfail", CTLFLAG_RD,
7553 &sc->sc_stats.ast_per_calfail, 0, "periodic calibration failed");
7554 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_per_rfgain", CTLFLAG_RD,
7555 &sc->sc_stats.ast_per_rfgain, 0, "periodic calibration rfgain reset");
7556 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_rate_calls", CTLFLAG_RD,
7557 &sc->sc_stats.ast_rate_calls, 0, "rate control checks");
7558 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_rate_raise", CTLFLAG_RD,
7559 &sc->sc_stats.ast_rate_raise, 0, "rate control raised xmit rate");
7560 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_rate_drop", CTLFLAG_RD,
7561 &sc->sc_stats.ast_rate_drop, 0, "rate control dropped xmit rate");
7562 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_ant_defswitch", CTLFLAG_RD,
7563 &sc->sc_stats.ast_ant_defswitch, 0, "rx/default antenna switches");
7564 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_ant_txswitch", CTLFLAG_RD,
7565 &sc->sc_stats.ast_ant_txswitch, 0, "tx antenna switches");
7566 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_cabq_xmit", CTLFLAG_RD,
7567 &sc->sc_stats.ast_cabq_xmit, 0, "cabq frames transmitted");
7568 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_cabq_busy", CTLFLAG_RD,
7569 &sc->sc_stats.ast_cabq_busy, 0, "cabq found busy");
7570 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_tx_raw", CTLFLAG_RD,
7571 &sc->sc_stats.ast_tx_raw, 0, "tx frames through raw api");
7572 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_ff_txok", CTLFLAG_RD,
7573 &sc->sc_stats.ast_ff_txok, 0, "fast frames tx'd successfully");
7574 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_ff_txerr", CTLFLAG_RD,
7575 &sc->sc_stats.ast_ff_txerr, 0, "fast frames tx'd w/ error");
7576 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_ff_rx", CTLFLAG_RD,
7577 &sc->sc_stats.ast_ff_rx, 0, "fast frames rx'd");
7578 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_ff_flush", CTLFLAG_RD,
7579 &sc->sc_stats.ast_ff_flush, 0, "fast frames flushed from staging q");
7580 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_tx_qfull", CTLFLAG_RD,
7581 &sc->sc_stats.ast_tx_qfull, 0, "tx dropped 'cuz of queue limit");
7582 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_tx_nobuf", CTLFLAG_RD,
7583 &sc->sc_stats.ast_tx_nobuf, 0, "tx dropped 'cuz no ath buffer");
7584 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_tdma_update", CTLFLAG_RD,
7585 &sc->sc_stats.ast_tdma_update, 0, "TDMA slot timing updates");
7586 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_tdma_timers", CTLFLAG_RD,
7587 &sc->sc_stats.ast_tdma_timers, 0, "TDMA slot update set beacon timers");
7588 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_tdma_tsf", CTLFLAG_RD,
7589 &sc->sc_stats.ast_tdma_tsf, 0, "TDMA slot update set TSF");
7590 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_tdma_ack", CTLFLAG_RD,
7591 &sc->sc_stats.ast_tdma_ack, 0, "TDMA tx failed 'cuz ACK required");
7592 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_tx_raw_fail", CTLFLAG_RD,
7593 &sc->sc_stats.ast_tx_raw_fail, 0, "raw tx failed 'cuz h/w down");
7594 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_tx_nofrag", CTLFLAG_RD,
7595 &sc->sc_stats.ast_tx_nofrag, 0, "tx dropped 'cuz no ath frag buffer");
7597 SYSCTL_ADD_UINT(ctx, child, OID_AUTO, "ast_be_missed", CTLFLAG_RD,
7598 &sc->sc_stats.ast_be_missed, 0, "number of -missed- beacons");