2 # LINT -- config file for checking all the sources, tries to pull in
3 # as much of the source tree as it can.
5 # $FreeBSD: src/sys/i386/conf/LINT,v 1.749.2.144 2003/06/04 17:56:59 sam Exp $
7 # See the kernconf(5) manual page for more information on the format of
10 # NB: You probably don't want to try running a kernel built from this
11 # file. Instead, you should start from GENERIC, and add options from
12 # this file as required.
15 # These directives are mandatory. The machine directive specifies the
16 # platform and the machine_arch directive specifies the cpu architecture.
23 # This is the ``identification'' of the kernel. Usually this should
24 # be the same as the name of your kernel.
29 # The `maxusers' parameter controls the static sizing of a number of
30 # internal system tables by a formula defined in subr_param.c. Setting
31 # maxusers to 0 will cause the system to auto-size based on physical
37 # The `makeoptions' parameter allows variables to be passed to the
38 # generated Makefile in the build area.
40 # CONF_CFLAGS gives some extra compiler flags that are added to ${CFLAGS}
41 # after most other flags. Here we use it to inhibit use of non-optimal
42 # gcc builtin functions (e.g., memcmp).
44 # DEBUG happens to be magic.
45 # The following is equivalent to 'config -g KERNELNAME' and creates
46 # 'kernel.debug' compiled with -g debugging as well as a normal
47 # 'kernel'. Use 'make install.debug' to install the debug kernel
48 # but that isn't normally necessary as the debug symbols are not loaded
49 # by the kernel and are not useful there anyway.
51 # KERNEL can be overridden so that you can change the default name of your
54 # MODULES_OVERRIDE can be used to limit modules built to a specific list.
56 # INSTALLSTRIPPED can be set to cause installkernel to install stripped
57 # kernels and modules rather than a kernel and modules with debug symbols.
59 # INSTALLSTRIPPEDMODULES can be set to allow a full debug kernel to be
60 # installed, but to strip the installed modules.
62 makeoptions CONF_CFLAGS=-fno-builtin #Don't allow use of memcmp, etc.
63 #makeoptions DEBUG=-g #Build kernel with gdb(1) debug symbols
64 #makeoptions KERNEL=foo #Build kernel "foo" and install "/foo"
65 # Only build Linux API modules and plus those parts of the sound system I need.
66 #makeoptions MODULES_OVERRIDE="linux sound/snd sound/pcm sound/driver/maestro3"
67 #makeoptions INSTALLSTRIPPED=1
68 #makeoptions INSTALLSTRIPPEDMODULES=1
71 # Certain applications can grow to be larger than the 128M limit
72 # that DragonFly initially imposes. Below are some options to
73 # allow that limit to grow to 256MB, and can be increased further
74 # with changing the parameters. MAXDSIZ is the maximum that the
75 # limit can be set to, and the DFLDSIZ is the default value for
76 # the limit. MAXSSIZ is the maximum that the stack limit can be
77 # set to. You might want to set the default lower than the max,
78 # and explicitly set the maximum with a shell command for processes
79 # that regularly exceed the limit like INND.
81 options MAXDSIZ="(256*1024*1024)"
82 options MAXSSIZ="(256*1024*1024)"
83 options DFLDSIZ="(256*1024*1024)"
86 # BLKDEV_IOSIZE sets the default block size used in user block
87 # device I/O. Note that this value will be overridden by the label
88 # when specifying a block device from a label with a non-0
89 # partition blocksize. The default is PAGE_SIZE.
91 options BLKDEV_IOSIZE=8192
93 # This allows you to actually store this configuration file into
94 # the kernel binary itself, where it may be later read by saying:
95 # strings -n 3 /kernel | sed -n 's/^___//p' > MYKERNEL
97 options INCLUDE_CONFIG_FILE # Include this file in kernel
100 # The root device and filesystem type can be compiled in;
101 # this provides a fallback option if the root device cannot
102 # be correctly guessed by the bootstrap code, or an override if
103 # the RB_DFLTROOT flag (-r) is specified when booting the kernel.
105 options ROOTDEVNAME=\"ufs:da0s2e\"
107 #####################################################################
111 # You must specify at least one CPU (the one you intend to run on);
112 # deleting the specification for CPUs you don't need to use may make
113 # parts of the system run faster.
116 cpu I586_CPU # aka Pentium(tm)
117 cpu I686_CPU # aka Pentium Pro(tm)
120 # Options for CPU features.
122 # CPU_ATHLON_SSE_HACK tries to enable SSE instructions when the BIOS has
123 # forgotten to enable them.
125 # CPU_BLUELIGHTNING_FPU_OP_CACHE enables FPU operand cache on IBM
126 # BlueLightning CPU. It works only with Cyrix FPU, and this option
127 # should not be used with Intel FPU.
129 # CPU_BLUELIGHTNING_3X enables triple-clock mode on IBM Blue Lightning
130 # CPU if CPU supports it. The default is double-clock mode on
131 # BlueLightning CPU box.
133 # CPU_DISABLE_SSE disables SSE/MMX2 instructions support.
135 # CPU_ENABLE_EST enables support for Enhanced SpeedStep technology
136 # found in Pentium(tm) M processors.
138 # CPU_ENABLE_LONGRUN enables support for Transmeta Crusoe LongRun
139 # technology which allows to restrict power consumption of the CPU by
140 # using group of hw.crusoe.* sysctls.
142 # CPU_ENABLE_TCC enables Thermal Control Circuitry (TCC) found in some
143 # Pentium(tm) 4 and (possibly) later CPUs. When enabled and detected,
144 # TCC supports restricting power consumption using the hw.p4tcc.*
145 # sysctls. This operates independently of SpeedStep and is useful on
146 # systems where other mechanisms such as apm(4) or acpi(4) don't work.
148 # CPU_HAS_SSE2 will enable the lfence and mfence instructions in
149 # cpu_lfence() and cpu_mfence(). If the CPU does not support them,
150 # it will cause a panic.
152 # CPU_I486_ON_386 enables CPU cache on i486 based CPU upgrade products
155 # CPU_L2_LATENCY specified the L2 cache latency value. This option is used
156 # only when CPU_PPRO2CELERON is defined and Mendocino Celeron is detected.
157 # The default value is 5.
159 # CPU_ELAN enables support for AMDs ElanSC520 CPU.
161 # CPU_GEODE enables support for AMD Geode LX, Geode SC1100 and AMD CS5536
163 # CPU_PPRO2CELERON enables L2 cache of Mendocino Celeron CPUs. This option
164 # is useful when you use Socket 8 to Socket 370 converter, because most Pentium
165 # Pro BIOSs do not enable L2 cache of Mendocino Celeron CPUs.
167 # CPU_WT_ALLOC enables write allocation on AMD K5/K6/K6-2 cpus.
169 # NO_F00F_HACK disables the hack that prevents Pentiums (and ONLY
170 # Pentiums) from locking up when a LOCK CMPXCHG8B instruction is
171 # executed. This option is only needed if I586_CPU is also defined,
172 # and should be included for any non-Pentium CPU that defines it.
174 # NO_MEMORY_HOLE is an optimisation for systems with AMD K6 processors
175 # which indicates that the 15-16MB range is *definitely* not being
176 # occupied by an ISA memory hole.
178 # NOTE 3: This option may cause failures for software that requires
179 # locked cycles in order to operate correctly.
181 options CPU_ATHLON_SSE_HACK
182 options CPU_BLUELIGHTNING_FPU_OP_CACHE
183 options CPU_BLUELIGHTNING_3X
184 options CPU_DISABLE_SSE
186 options CPU_ENABLE_EST
187 options CPU_ENABLE_LONGRUN
188 options CPU_ENABLE_TCC
191 options CPU_I486_ON_386
192 options CPU_L2_LATENCY=5
193 options CPU_PPRO2CELERON
195 #options NO_F00F_HACK
196 options NO_MEMORY_HOLE
199 # A math emulator is mandatory if you wish to run on hardware which
200 # does not have a floating-point processor.
201 options MATH_EMULATE #Support for x87 emulation
203 #####################################################################
204 # COMPATIBILITY OPTIONS
207 # Implement system calls compatible with 4.3BSD and older versions of
208 # FreeBSD. You probably do NOT want to remove this as much current code
209 # still relies on the 4.3 emulation.
214 # Implement system calls compatible with DragonFly 1.2 and older.
216 options COMPAT_DF12 #Compatible with DragonFly 1.2 and earlier
218 # Enable NDIS binary driver support
223 # These three options provide support for System V Interface
224 # Definition-style interprocess communication, in the form of shared
225 # memory, semaphores, and message queues, respectively.
227 # System V shared memory and tunable parameters
228 options SYSVSHM # include support for shared memory
229 options SHMMIN=2 # min shared memory segment size (bytes)
230 options SHMMNI=33 # max number of shared memory identifiers
231 options SHMSEG=9 # max shared memory segments per process
233 # System V semaphores and tunable parameters
234 options SYSVSEM # include support for semaphores
235 options SEMMAP=31 # amount of entries in semaphore map
236 options SEMMNI=11 # number of semaphore identifiers in the system
237 options SEMMNS=61 # number of semaphores in the system
238 options SEMMNU=31 # number of undo structures in the system
239 options SEMMSL=61 # max number of semaphores per id
240 options SEMOPM=101 # max number of operations per semop call
241 options SEMUME=11 # max number of undo entries per process
243 # System V message queues and tunable parameters
244 options SYSVMSG # include support for message queues
245 options MSGMNB=2049 # max characters per message queue
246 options MSGMNI=41 # max number of message queue identifiers
247 options MSGSEG=2049 # max number of message segments in the system
248 options MSGSSZ=16 # size of a message segment MUST be power of 2
249 options MSGTQL=41 # max amount of messages in the system
251 #####################################################################
255 # Enable the kernel debugger.
260 # Print a stack trace on kernel panic.
265 # Don't drop into DDB for a panic. Intended for unattended operation
266 # where you may want to drop to DDB from the console, but still want
267 # the machine to recover from a panic
269 options DDB_UNATTENDED
272 # If using GDB remote mode to debug the kernel, there's a non-standard
273 # extension to the remote protocol that can be used to use the serial
274 # port as both the debugging port and the system console. It's non-
275 # standard and you're on your own if you enable it. See also the
276 # "remotechat" variables in the DragonFly specific version of gdb.
278 options GDB_REMOTE_CHAT
281 # KTRACE enables the system-call tracing facility ktrace(2).
283 options KTRACE #kernel tracing
286 # The INVARIANTS option is used in a number of source files to enable
287 # extra sanity checking of internal structures. This support is not
288 # enabled by default because of the extra time it would take to check
289 # for these conditions, which can only occur as a result of
290 # programming errors.
295 # The DIAGNOSTIC option is used to enable extra debugging information
296 # from some parts of the kernel. As this makes everything more noisy,
297 # it is disabled by default.
302 # PERFMON causes the driver for Pentium/Pentium Pro performance counters
303 # to be compiled. See perfmon(4) for more information.
309 # This option let some drivers co-exist that can't co-exist in a running
310 # system. This is used to be able to compile all kernel code in one go for
311 # quality assurance purposes (like this file, which the option takes it name
314 options COMPILING_LINT
317 # XXX - this doesn't belong here.
318 # Allow ordinary users to take the console - this is useful for X.
321 # XXX - this doesn't belong here either
322 options USERCONFIG #boot -c editor
323 options INTRO_USERCONFIG #imply -c and show intro screen
324 options VISUAL_USERCONFIG #visual boot -c editor
326 #####################################################################
331 # Only the INET (Internet) family is officially supported in DragonFly.
332 # Source code for the NS (Xerox Network Service) is provided for amusement
335 options INET #Internet communications protocols
336 options INET6 #IPv6 communications protocols
337 options IPSEC #IP security
338 options IPSEC_ESP #IP security (crypto; define w/ IPSEC)
339 options IPSEC_DEBUG #debug for IP security
341 # Set IPSEC_FILTERGIF to force packets coming through a gif tunnel
342 # to be processed by any configured packet filtering (ipfw).
343 # The default is that packets coming from a tunnel are _not_ processed;
344 # they are assumed trusted.
346 # Note that enabling this can be problematic as there are no mechanisms
347 # in place for distinguishing packets coming out of a tunnel (e.g. no
348 # encX devices as found on openbsd).
350 #options IPSEC_FILTERGIF #filter ipsec packets from a tunnel
353 # Experimental IPsec implementation that uses the kernel crypto
354 # framework. This cannot be configured together with IPSEC and
355 # (currently) supports only IPv4. To use this you must also
356 # configure the crypto device (see below). Note that with this
357 # you get all the IPsec protocols (e.g. there is no FAST_IPSEC_ESP).
358 # IPSEC_DEBUG is used, as above, to configure debugging support
359 # within the IPsec protocols.
361 #options FAST_IPSEC #new IPsec
363 options IPX #IPX/SPX communications protocols
364 options IPXIP #IPX in IP encapsulation (not available)
365 options IPTUNNEL #IP in IPX encapsulation (not available)
367 options NCP #NetWare Core protocol
369 options MPLS #Multi-Protocol Label Switching
373 # NETSMB enables support for SMB protocol, it requires LIBMCHAIN and LIBICONV
375 # NETSMBCRYPTO enables support for encrypted passwords.
376 options NETSMB #SMB/CIFS requester
377 options NETSMBCRYPTO #encrypted password support for SMB
379 # mchain library. It can be either loaded as KLD or compiled into kernel
380 options LIBMCHAIN #mbuf management library
382 # netgraph(4). Enable the base netgraph code with the NETGRAPH option.
383 # Individual node types can be enabled with the corresponding option
384 # listed below; however, this is not strictly necessary as netgraph
385 # will automatically load the corresponding KLD module if the node type
386 # is not already compiled into the kernel. Each type below has a
387 # corresponding man page, e.g., ng_async(4).
388 options NETGRAPH #netgraph(4) system
389 options NETGRAPH_ASYNC
391 options NETGRAPH_BRIDGE
392 options NETGRAPH_CISCO
393 options NETGRAPH_ECHO
394 options NETGRAPH_EIFACE
395 options NETGRAPH_ETHER
397 options NETGRAPH_FRAME_RELAY
398 options NETGRAPH_HOLE
399 options NETGRAPH_IFACE
400 options NETGRAPH_KSOCKET
401 options NETGRAPH_L2TP
403 # MPPC compression requires proprietary files (not included)
404 #options NETGRAPH_MPPC_COMPRESSION
405 options NETGRAPH_MPPC_ENCRYPTION
406 options NETGRAPH_ONE2MANY
408 options NETGRAPH_PPPOE
409 options NETGRAPH_PPTPGRE
410 options NETGRAPH_RFC1490
411 options NETGRAPH_SOCKET
417 device mn # Munich32x/Falc54 Nx64kbit/sec cards.
420 # Network interfaces:
421 # The `loop' pseudo-device is MANDATORY when networking is enabled.
422 # The `ether' pseudo-device provides generic code to handle
423 # Ethernets; it is MANDATORY when a Ethernet device driver is
425 # The `sppp' pseudo-device serves a similar role for certain types
426 # of synchronous PPP links (like `ar').
427 # The `sl' pseudo-device implements the Serial Line IP (SLIP) service.
428 # The `ppp' pseudo-device implements the Point-to-Point Protocol.
429 # The `bpf' pseudo-device enables the Berkeley Packet Filter. Be
430 # aware of the legal and administrative consequences of enabling this
431 # option. The number of devices determines the maximum number of
432 # simultaneous BPF clients programs runnable.
433 # The `disc' pseudo-device implements a minimal network interface,
434 # which throws away all packets sent and never receives any. It is
435 # included for testing purposes. This shows up as the 'ds' interface.
436 # The `tun' pseudo-device implements (user-)ppp and nos-tun
437 # The `gif' pseudo-device implements IPv6 over IP4 tunneling,
438 # IPv4 over IPv6 tunneling, IPv4 over IPv4 tunneling and
439 # IPv6 over IPv6 tunneling.
440 # The `gre' device implements two types of IP4 over IP4 tunneling:
441 # GRE and MOBILE, as specified in the RFC1701 and RFC2004.
442 # The `faith' pseudo-device captures packets sent to it and diverts them
443 # to the IPv4/IPv6 translation daemon.
444 # The `stf' device implements 6to4 encapsulation.
445 # The `ef' pseudo-device provides support for multiple ethernet frame types
446 # specified via ETHER_* options. See ef(4) for details.
448 # The PPP_BSDCOMP option enables support for compress(1) style entire
449 # packet compression, the PPP_DEFLATE is for zlib/gzip style compression.
450 # PPP_FILTER enables code for filtering the ppp data stream and selecting
451 # events for resetting the demand dial activity timer - requires bpf.
452 # See pppd(8) for more details.
454 pseudo-device ether #Generic Ethernet
455 pseudo-device vlan 1 #VLAN support
456 pseudo-device bridge #Bridging support
457 pseudo-device sppp #Generic Synchronous PPP
458 pseudo-device loop #Network loopback device
459 pseudo-device bpf #Berkeley packet filter
460 pseudo-device disc #Discard device (ds0, ds1, etc)
461 pseudo-device tap #Ethernet tunnel network interface
462 pseudo-device tun #Tunnel driver (ppp(8), nos-tun(8))
463 pseudo-device sl 2 #Serial Line IP
464 pseudo-device gre #IP over IP tunneling
465 pseudo-device ppp 2 #Point-to-point protocol
466 options PPP_BSDCOMP #PPP BSD-compress support
467 options PPP_DEFLATE #PPP zlib/deflate/gzip support
468 options PPP_FILTER #enable bpf filtering (needs bpf)
470 pseudo-device ef # Multiple ethernet frames support
471 options ETHER_II # enable Ethernet_II frame
472 options ETHER_8023 # enable Ethernet_802.3 (Novell) frame
473 options ETHER_8022 # enable Ethernet_802.2 frame
474 options ETHER_SNAP # enable Ethernet_802.2/SNAP frame
477 pseudo-device gif #IPv6 and IPv4 tunneling
478 pseudo-device faith 1 #for IPv6 and IPv4 translation
479 pseudo-device stf #6to4 IPv6 over IPv4 encapsulation
482 # Internet family options:
484 # MROUTING enables the kernel multicast packet forwarder, which works
487 # PIM enables Protocol Independent Multicast in the kernel.
488 # Requires MROUTING enabled.
490 # IPFIREWALL enables support for IP firewall construction, in
491 # conjunction with the `ipfw' program. IPFIREWALL_VERBOSE sends
492 # logged packets to the system logger. IPFIREWALL_VERBOSE_LIMIT
493 # limits the number of times a matching entry can be logged.
495 # WARNING: IPFIREWALL defaults to a policy of "deny ip from any to any"
496 # and if you do not add other rules during startup to allow access,
497 # YOU WILL LOCK YOURSELF OUT. It is suggested that you set firewall_type=open
498 # in /etc/rc.conf when first enabling this feature, then refining the
499 # firewall rules in /etc/rc.firewall after you've tested that the new kernel
500 # feature works properly.
502 # IPFIREWALL_DEFAULT_TO_ACCEPT causes the default rule (at boot) to
503 # allow everything. Use with care, if a cracker can crash your
504 # firewall machine, they can get to your protected machines. However,
505 # if you are using it as an as-needed filter for specific problems as
506 # they arise, then this may be for you. Changing the default to 'allow'
507 # means that you won't get stuck if the kernel and /sbin/ipfw binary get
510 # IPDIVERT enables the divert IP sockets, used by ``ipfw divert''
512 # IPSTEALTH enables code to support stealth forwarding (i.e., forwarding
513 # packets without touching the ttl). This can be useful to hide firewalls
514 # from traceroute and similar tools.
516 # TCPDEBUG is undocumented.
518 options MROUTING # Multicast routing
519 options PIM # Protocol Independent Multicast
520 options IPFIREWALL #firewall
521 options IPFIREWALL_DEBUG #debug prints
522 options IPFIREWALL_VERBOSE #enable logging to syslogd(8)
523 options IPFIREWALL_VERBOSE_LIMIT=100 #limit verbosity
524 options IPFIREWALL_DEFAULT_TO_ACCEPT #allow everything by default
525 options IPV6FIREWALL #firewall for IPv6
526 options IPV6FIREWALL_VERBOSE
527 options IPV6FIREWALL_VERBOSE_LIMIT=100
528 options IPV6FIREWALL_DEFAULT_TO_ACCEPT
529 options IPDIVERT #divert sockets
530 options IPSTEALTH #support for stealth forwarding
540 # The MBUF_STRESS_TEST option enables options which create
541 # various random failures / extreme cases related to mbuf
542 # functions. See the mbuf(9) manpage for a list of available
544 options MBUF_STRESS_TEST
546 # Statically link in accept filters
547 options ACCEPT_FILTER_DATA
548 options ACCEPT_FILTER_HTTP
550 # TCP_SIGNATURE adds support for RFC 2385 (TCP-MD5) digests. These are
551 # carried in TCP option 19. This option is commonly used to protect
552 # TCP sessions (e.g. BGP) where IPSEC is not available nor desirable.
553 # This is enabled on a per-socket basis using the TCP_SIGNATURE_ENABLE
555 # This requires the use of 'device crypto', 'options IPSEC'
556 # or 'device cryptodev'.
557 options TCP_SIGNATURE #include support for RFC 2385
560 # TCP_DROP_SYNFIN adds support for ignoring TCP packets with SYN+FIN. This
561 # prevents nmap et al. from identifying the TCP/IP stack, but breaks support
562 # for RFC1644 extensions and is not recommended for web servers.
564 options TCP_DROP_SYNFIN #drop TCP packets with SYN+FIN
566 # ICMP_BANDLIM enables icmp error response bandwidth limiting. You
567 # typically want this option as it will help protect the machine from
568 # D.O.S. packet attacks.
572 # DUMMYNET enables the "dummynet" bandwidth limiter. You need
573 # IPFIREWALL as well. See the dummynet(4) and ipfw(8) manpages for more info.
576 options DUMMYNET_DEBUG
579 # ATM (HARP version) options
581 # ATM_CORE includes the base ATM functionality code. This must be included
584 # ATM_IP includes support for running IP over ATM.
586 # At least one (and usually only one) of the following signalling managers
587 # must be included (note that all signalling managers include PVC support):
588 # ATM_SIGPVC includes support for the PVC-only signalling manager `sigpvc'.
589 # ATM_SPANS includes support for the `spans' signalling manager, which runs
590 # the FORE Systems's proprietary SPANS signalling protocol.
591 # ATM_UNI includes support for the `uni30' and `uni31' signalling managers,
592 # which run the ATM Forum UNI 3.x signalling protocols.
594 # The `hea' driver provides support for the Efficient Networks, Inc.
595 # ENI-155p ATM PCI Adapter.
597 # The `hfa' driver provides support for the FORE Systems, Inc.
598 # PCA-200E ATM PCI Adapter.
600 options ATM_CORE #core ATM protocol family
601 options ATM_IP #IP over ATM support
602 options ATM_SIGPVC #SIGPVC signalling manager
603 options ATM_SPANS #SPANS signalling manager
604 options ATM_UNI #UNI signalling manager
605 device hea #Efficient ENI-155p ATM PCI
606 device hfa #FORE PCA-200E ATM PCI
608 # IFPOLL_ENABLE adds support for mixed interrupt-polling handling
609 # of network device drivers, which has significant benefits in terms
610 # of robustness to overloads and responsivity, as well as permitting
611 # accurate scheduling of the CPU time between kernel network processing
612 # and other activities. The drawback is a moderate (up to 1/pollhz seconds)
613 # potential increase in response times. See polling(4) for further details.
615 # IFPOLL_ENABLE adds hardware queues' based polling
616 options IFPOLL_ENABLE
618 #####################################################################
622 # Only the root, /usr, and /tmp filesystems need be statically
623 # compiled; everything else will be automatically loaded at mount
624 # time. (Exception: the UFS family --- FFS, and MFS ---
625 # cannot currently be demand-loaded.) Some people still prefer
626 # to statically compile other filesystems as well.
628 # NB: The PORTAL and UNION filesystems are known to be
629 # buggy, and WILL panic your system if you attempt to do anything with
630 # them. They are included here as an incentive for some enterprising
631 # soul to sit down and fix them.
634 # One of these is mandatory:
635 options FFS #Fast filesystem
636 options MFS #Memory filesystem
637 options NFS #Network filesystem
639 # The rest are optional:
640 #options NFS_NOSERVER #Disable the NFS-server code.
641 options CD9660 #ISO 9660 filesystem
642 options FDESC #File descriptor filesystem
643 options HAMMER #HAMMER filesystem
644 options HPFS #OS/2 File system
645 options MSDOSFS #MS DOS filesystem
646 options NTFS #NT filesystem
647 options NULLFS #NULL filesystem
648 options NWFS #NetWare filesystem
649 options PORTAL #Portal filesystem
650 options PROCFS #Process filesystem
651 options PUFFS #Userspace file systems (e.g. ntfs-3g & sshfs)
652 options SMBFS #SMB/CIFS filesystem
653 options TMPFS #Temporary filesystem
654 options UDF #UDF filesystem
656 # YYY-DR Till we rework the VOP methods for this filesystem
657 #options UNION #Union filesystem
658 # The xFS_ROOT options REQUIRE the associated ``options xFS''
659 options FFS_ROOT #FFS usable as root device
660 options NFS_ROOT #NFS usable as root device
662 # Soft updates is technique for improving UFS filesystem speed and
663 # making abrupt shutdown less risky.
666 # Directory hashing improves the speed of operations on very large
667 # directories at the expense of some memory.
670 # Make space in the kernel for a root filesystem on a md device.
671 # Define to the number of kilobytes to reserve for the filesystem.
672 options MD_ROOT_SIZE=10
674 # Make the md device a potential root device, either with preloaded
675 # images of type mfs_root or md_root.
678 # Specify double the default maximum size for malloc(9)-backed md devices.
679 options MD_NSECT=40000
681 # Allow this many swap-devices.
683 # In order to manage swap, the system must reserve bitmap space that
684 # scales with the largest mounted swap device multiplied by NSWAPDEV,
685 # regardless of whether other swap devices exist or not. So it
686 # is not a good idea to make this value too large.
689 # Disk quotas are supported when this option is enabled.
690 options QUOTA #enable disk quotas
692 # If you are running a machine just as a fileserver for PC and MAC
693 # users, e.g. using SAMBA, you may consider setting this option
694 # and keeping all those users' directories on a filesystem that is
695 # mounted with the suiddir option. This gives new files the same
696 # ownership as the directory (similar to group). It's a security hole
697 # if you let these users run programs, so confine it to file-servers
698 # (but it'll save you lots of headaches in those cases). Root owned
699 # directories are exempt and X bits are cleared. The suid bit must be
700 # set on the directory as well; see chmod(1) PC owners can't see/set
701 # ownerships so they keep getting their toes trodden on. This saves
702 # you all the support calls as the filesystem it's used on will act as
703 # they expect: "It's my dir so it must be my file".
708 options NFS_MINATTRTIMO=3 # VREG attrib cache timeout in sec
709 options NFS_MAXATTRTIMO=60
710 options NFS_MINDIRATTRTIMO=30 # VDIR attrib cache timeout in sec
711 options NFS_MAXDIRATTRTIMO=60
712 options NFS_GATHERDELAY=10 # Default write gather delay (msec)
713 options NFS_UIDHASHSIZ=29 # Tune the size of nfssvc_sock with this
714 options NFS_WDELAYHASHSIZ=16 # and with this
715 options NFS_MUIDHASHSIZ=63 # Tune the size of nfsmount with this
716 options NFS_DEBUG # Enable NFS Debugging
722 options MSDOSFS_DEBUG # Enable MSDOSFS Debugging
725 # Add support for the EXT2FS filesystem of Linux fame. Be a bit
726 # careful with this - the ext2fs code has a tendency to lag behind
727 # changes and not be exercised very much, so mounting read/write could
728 # be dangerous (and even mounting read only could result in panics.)
732 # Optional character code conversion support with LIBICONV.
733 # Each option requires their base file system and LIBICONV.
735 options MSDOSFS_ICONV
738 #####################################################################
741 # Real time extensions added in the 1993 Posix
742 # P1003_1B: Infrastructure
743 # _KPOSIX_PRIORITY_SCHEDULING: Build in _POSIX_PRIORITY_SCHEDULING
744 # _KPOSIX_VERSION: Version kernel is built for
747 options _KPOSIX_PRIORITY_SCHEDULING
748 options _KPOSIX_VERSION=199309L
750 #####################################################################
753 # The granularity of operation is controlled by the kernel option HZ whose
754 # default value (100) means a granularity of 10ms (1s/HZ).
755 # Consider, however, that reducing the granularity too much might
756 # cause excessive overhead in clock interrupt processing,
757 # potentially causing ticks to be missed and thus actually reducing
758 # the accuracy of operation.
762 # The following options are used for debugging clock behavior only, and
763 # should not be used for production systems.
765 # CLK_CALIBRATION_LOOP will run the clock calibration loop at startup
766 # until the user presses a key.
768 options CLK_CALIBRATION_LOOP
770 # The following two options measure the frequency of the corresponding
771 # clock relative to the RTC (onboard mc146818a).
773 options CLK_USE_I8254_CALIBRATION
774 options CLK_USE_TSC_CALIBRATION
776 #####################################################################
779 # SCSI DEVICE CONFIGURATION
781 # The SCSI subsystem consists of the `base' SCSI code, a number of
782 # high-level SCSI device `type' drivers, and the low-level host-adapter
783 # device drivers. The host adapters are listed in the ISA and PCI
784 # device configuration sections below.
786 # Beginning with FreeBSD 2.0.5 you can wire down your SCSI devices so
787 # that a given bus, target, and LUN always come on line as the same
788 # device unit. In earlier versions the unit numbers were assigned
789 # in the order that the devices were probed on the SCSI bus. This
790 # means that if you removed a disk drive, you may have had to rewrite
791 # your /etc/fstab file, and also that you had to be careful when adding
792 # a new disk as it may have been probed earlier and moved your device
793 # configuration around.
795 # This old behavior is maintained as the default behavior. The unit
796 # assignment begins with the first non-wired down unit for a device
797 # type. For example, if you wire a disk as "da3" then the first
798 # non-wired disk will be assigned da4.
800 # The syntax for wiring down devices is:
802 # device scbus0 at ahc0 # Single bus device
803 # device scbus1 at ahc1 bus 0 # Single bus device
804 # device scbus3 at ahc2 bus 0 # Twin bus device
805 # device scbus2 at ahc2 bus 1 # Twin bus device
806 # device da0 at scbus0 target 0 unit 0
807 # device da1 at scbus3 target 1
808 # device da2 at scbus2 target 3
809 # device sa1 at scbus1 target 6
812 # "units" (SCSI logical unit number) that are not specified are
813 # treated as if specified as LUN 0.
815 # All SCSI devices allocate as many units as are required.
817 # The "unknown" device (uk? in pre-2.0.5) is now part of the base SCSI
818 # configuration and doesn't have to be explicitly configured.
820 device scbus #base SCSI code
821 device ch #SCSI media changers
822 device da #SCSI direct access devices (aka disks)
823 device sa #SCSI tapes
824 device cd #SCSI CD-ROMs
825 device pass #CAM passthrough driver
826 device sg #Passthrough device (linux scsi generic)
827 device pt #SCSI processor type
828 device ses #SCSI SES/SAF-TE driver
829 device targ #SCSI Target Mode Code
830 device targbh #SCSI Target Mode Blackhole Device
832 # Options for device mapper
834 device dm_target_crypt
835 device dm_target_linear
836 device dm_target_striped
839 device iscsi_initiator
840 options ISCSI_INITIATOR_DEBUG=8
844 # -- NOTE -- If you specify one of the bus/target/lun options, you must
846 # CAMDEBUG: When defined enables debugging macros
847 # CAM_DEBUG_BUS: Debug the given bus. Use -1 to debug all busses.
848 # CAM_DEBUG_TARGET: Debug the given target. Use -1 to debug all targets.
849 # CAM_DEBUG_LUN: Debug the given lun. Use -1 to debug all luns.
850 # CAM_DEBUG_FLAGS: OR together CAM_DEBUG_INFO, CAM_DEBUG_TRACE,
851 # CAM_DEBUG_SUBTRACE, and CAM_DEBUG_CDB
853 # CAM_MAX_HIGHPOWER: Maximum number of concurrent high power (start unit) cmds
854 # SCSI_NO_SENSE_STRINGS: When defined disables sense descriptions
855 # SCSI_NO_OP_STRINGS: When defined disables opcode descriptions
856 # SCSI_DELAY: The number of MILLISECONDS to freeze the SIM (scsi adapter)
857 # queue after a bus reset, and the number of milliseconds to
858 # freeze the device queue after a bus device reset. This
859 # can be changed at boot and runtime with the
860 # kern.cam.scsi_delay tunable/sysctl.
862 options CAM_DEBUG_BUS=-1
863 options CAM_DEBUG_TARGET=-1
864 options CAM_DEBUG_LUN=-1
865 options CAM_DEBUG_FLAGS="CAM_DEBUG_INFO|CAM_DEBUG_TRACE|CAM_DEBUG_CDB"
866 options CAM_MAX_HIGHPOWER=4
867 options SCSI_NO_SENSE_STRINGS
868 options SCSI_NO_OP_STRINGS
869 options SCSI_DELAY=8000 # Be pessimistic about Joe SCSI device
871 # Options for the CAM CDROM driver:
872 # CHANGER_MIN_BUSY_SECONDS: Guaranteed minimum time quantum for a changer LUN
873 # CHANGER_MAX_BUSY_SECONDS: Maximum time quantum per changer LUN, only
874 # enforced if there is I/O waiting for another LUN
875 # The compiled in defaults for these variables are 2 and 10 seconds,
878 # These can also be changed on the fly with the following sysctl variables:
879 # kern.cam.cd.changer.min_busy_seconds
880 # kern.cam.cd.changer.max_busy_seconds
882 options CHANGER_MIN_BUSY_SECONDS=2
883 options CHANGER_MAX_BUSY_SECONDS=10
885 # Options for the CAM sequential access driver:
886 # SA_IO_TIMEOUT: Timeout for read/write/wfm operations, in minutes
887 # SA_SPACE_TIMEOUT: Timeout for space operations, in minutes
888 # SA_REWIND_TIMEOUT: Timeout for rewind operations, in minutes
889 # SA_ERASE_TIMEOUT: Timeout for erase operations, in minutes
890 # SA_1FM_AT_EOD: Default to model which only has a default one filemark at EOT.
891 options SA_IO_TIMEOUT="(4)"
892 options SA_SPACE_TIMEOUT="(60)"
893 options SA_REWIND_TIMEOUT="(2*60)"
894 options SA_ERASE_TIMEOUT="(4*60)"
895 options SA_1FM_AT_EOD
897 # Optional timeout for the CAM processor target (pt) device
898 # This is specified in seconds. The default is 60 seconds.
899 options SCSI_PT_DEFAULT_TIMEOUT="60"
901 # Optional enable of doing SES passthrough on other devices (e.g., disks)
903 # Normally disabled because a lot of newer SCSI disks report themselves
904 # as having SES capabilities, but this can then clot up attempts to build
905 # build a topology with the SES device that's on the box these drives
907 options SES_ENABLE_PASSTHROUGH
909 #####################################################################
910 # MISCELLANEOUS DEVICES AND OPTIONS
912 # The `pty' device usually turns out to be ``effectively mandatory'',
913 # as it is required for `telnetd', `rlogind', `screen', `emacs', and
914 # `xterm', among others.
916 pseudo-device pty #Pseudo ttys
917 pseudo-device gzip #Exec gzipped a.out's
918 pseudo-device vn #Vnode driver (turns a file into a device)
919 pseudo-device md #Memory/malloc disk
920 pseudo-device putter #for puffs and pud
921 pseudo-device snp #Snoop device - to look at pty/vty/etc..
922 pseudo-device ccd 4 #Concatenated disk driver
924 # Configuring Vinum into the kernel is not necessary, since the kld
925 # module gets started automatically when vinum(8) starts. This
926 # device is also untested. Use at your own risk.
928 # The option VINUMDEBUG must match the value set in CFLAGS
929 # in src/sbin/vinum/Makefile. Failure to do so will result in
930 # the following message from vinum(8):
932 # Can't get vinum config: Invalid argument
934 # see vinum(4) for more reasons not to use these options.
935 pseudo-device vinum #Vinum concat/mirror/raid driver
936 options VINUMDEBUG #enable Vinum debugging hooks
938 # Kernel side iconv library
941 # Size of the kernel message buffer. Should be N * pagesize.
942 options MSGBUF_SIZE=40960
944 #####################################################################
945 # HARDWARE DEVICE CONFIGURATION
950 # Mandatory ISA devices: isa, npx
954 # ISA-PnP BIOS support
960 # AUTO_EOI_1 enables the `automatic EOI' feature for the master 8259A
961 # interrupt controller. This saves about 0.7-1.25 usec for each interrupt.
962 # This option breaks suspend/resume on some portables.
964 # AUTO_EOI_2 enables the `automatic EOI' feature for the slave 8259A
965 # interrupt controller. This saves about 0.7-1.25 usec for each interrupt.
966 # Automatic EOI is documented not to work for the slave with the
967 # original i8259A, but it works for some clones and some integrated
970 # MAXMEM specifies the amount of RAM on the machine; if this is not
971 # specified, DragonFly will first read the amount of memory from the CMOS
972 # RAM, so the amount of memory will initially be limited to 64MB or 16MB
973 # depending on the BIOS. If the BIOS reports 64MB, a memory probe will
974 # then attempt to detect the installed amount of RAM. If this probe
975 # fails to detect >64MB RAM you will have to use the MAXMEM option.
976 # The amount is in kilobytes, so for a machine with 128MB of RAM, it would
977 # be 131072 (128 * 1024).
979 # BROKEN_KEYBOARD_RESET disables the use of the keyboard controller to
980 # reset the CPU for reboot. This is needed on some systems with broken
981 # keyboard controllers.
985 options MAXMEM="(128*1024)"
986 #options BROKEN_KEYBOARD_RESET
988 # Enable support for the kernel PLL to use an external PPS signal,
989 # under supervision of [x]ntpd(8)
990 # More info in ntpd documentation: http://www.eecis.udel.edu/~ntp
994 # The keyboard controller; it controls the keyboard and the PS/2 mouse.
995 device atkbdc0 at isa? port IO_KBD
998 device atkbd0 at atkbdc? irq 1
1000 # Options for atkbd:
1001 options ATKBD_DFLT_KEYMAP # specify the built-in keymap
1002 makeoptions ATKBD_DFLT_KEYMAP="jp.106"
1004 # These options are valid for other keyboard drivers as well.
1005 options KBD_DISABLE_KEYMAP_LOAD # refuse to load a keymap
1006 options KBD_INSTALL_CDEV # install a CDEV entry in /dev
1008 # `flags' for atkbd:
1009 # 0x01 Force detection of keyboard, else we always assume a keyboard
1010 # 0x02 Don't reset keyboard, useful for some newer ThinkPads
1011 # 0x03 Force detection and avoid reset, might help with certain
1013 # 0x04 Old-style (XT) keyboard support, useful for older ThinkPads
1016 device psm0 at atkbdc? irq 12
1019 options PSM_HOOKRESUME #hook the system resume event, useful
1021 options PSM_RESETAFTERSUSPEND #reset the device at the resume event
1023 device kbdmux # keyboard multiplexer
1025 # The video card driver.
1029 # Try the following option if the mouse pointer is not drawn correctly
1030 # or font does not seem to be loaded properly. May cause flicker on
1032 options VGA_ALT_SEQACCESS
1034 options VGA_DEBUG=2 # enable VGA debug output
1036 # If you experience problems switching back to 80x25 (or a derived mode),
1037 # the following option might help.
1038 #options VGA_KEEP_POWERON_MODE # use power-on settings for 80x25
1040 # If you can dispense with some vga driver features, you may want to
1041 # use the following options to save some memory.
1042 #options VGA_NO_FONT_LOADING # don't save/load font
1043 #options VGA_NO_MODE_CHANGE # don't change video modes
1045 # The following option probably won't work with the LCD displays.
1046 options VGA_WIDTH90 # support 90 column modes
1048 # To include support for VESA video modes
1050 options VESA_DEBUG=2 # enable VESA debug output
1052 # Splash screen at start up! Screen savers require this too.
1053 pseudo-device splash
1055 # The syscons console driver (sco color console compatible).
1057 options MAXCONS=16 # number of virtual consoles
1058 options SC_ALT_MOUSE_IMAGE # simplified mouse cursor in text mode
1059 options SC_DEBUG_LEVEL=5 # enable debug output
1060 options SC_DFLT_FONT # compile font in
1061 makeoptions SC_DFLT_FONT=cp850
1062 options SC_DISABLE_DDBKEY # disable `debug' key
1063 options SC_DISABLE_REBOOT # disable reboot key sequence
1064 options SC_HISTORY_SIZE=200 # number of history buffer lines
1065 options SC_MOUSE_CHAR=0x3 # char code for text mode mouse cursor
1066 options SC_PIXEL_MODE # add support for the raster text mode
1068 # The following options will let you change the default colors of syscons.
1069 options SC_NORM_ATTR="(FG_GREEN|BG_BLACK)"
1070 options SC_NORM_REV_ATTR="(FG_YELLOW|BG_GREEN)"
1071 options SC_KERNEL_CONS_ATTR="(FG_RED|BG_BLACK)"
1072 options SC_KERNEL_CONS_REV_ATTR="(FG_BLACK|BG_RED)"
1074 # If you have a two button mouse, you may want to add the following option
1075 # to use the right button of the mouse to paste text.
1076 options SC_TWOBUTTON_MOUSE
1078 # You can selectively disable features in syscons.
1079 #options SC_NO_CUTPASTE
1080 #options SC_NO_FONT_LOADING
1081 #options SC_NO_HISTORY
1082 #options SC_NO_SYSMOUSE
1085 # The Numeric Processing eXtension driver. In addition to this, you
1086 # may configure a math emulator (see above). If your machine has a
1087 # hardware FPU and the kernel configuration includes the npx device
1088 # *and* a math emulator compiled into the kernel, the hardware FPU
1089 # will be used, unless it is found to be broken or unless "flags" to
1090 # npx0 includes "0x08", which requests preference for the emulator.
1091 device npx0 at nexus? port IO_NPX flags 0x0 irq 13
1095 # 0x01 don't use the npx registers to optimize bcopy.
1096 # 0x02 don't use the npx registers to optimize bzero.
1097 # 0x04 don't use the npx registers to optimize copyin or copyout.
1098 # 0x08 use emulator even if hardware FPU is available.
1099 # The npx registers are normally used to optimize copying and zeroing when
1100 # all of the following conditions are satisfied:
1101 # I586_CPU is an option
1102 # the cpu is an i586 (perhaps not a Pentium)
1103 # the probe for npx0 succeeds
1104 # INT 16 exception handling works.
1105 # Then copying and zeroing using the npx registers is normally 30-100% faster.
1106 # The flags can be used to control cases where it doesn't work or is slower.
1107 # Setting them at boot time using userconfig works right (the optimizations
1108 # are not used until later in the bootstrap when npx0 is attached).
1109 # Flag 0x08 automatically disables the i586 optimized routines.
1113 # SCSI host adapters
1115 # adv: All Narrow SCSI bus AdvanSys controllers.
1116 # adw: Second Generation AdvanSys controllers including the ADV940UW.
1117 # ahc: Adaptec 274x/284x/294x
1119 # bt: Most Buslogic controllers
1120 # ncv: NCR 53C500 based SCSI host adapters.
1121 # nsp: Workbit Ninja SCSI-3 based PC Card SCSI host adapters.
1122 # stg: TMC 18C30, 18C50 based ISA/PC Card SCSI host adapters.
1124 # Note that the order is important in order for Buslogic cards to be
1134 device stg0 at isa? port 0x140 irq 11
1137 # Adaptec FSA RAID controllers, including integrated DELL controller,
1138 # the Dell PERC 2/QC and the HP NetRAID-4M
1142 device aacp # SCSI Passthrough interface (optional, CAM required)
1145 # Compaq Smart RAID, Mylex DAC960 and AMI MegaRAID controllers. Only
1146 # one entry is needed; the code will find and configure all supported
1149 device ida # Compaq Smart RAID
1150 device mlx # Mylex DAC960
1151 device amr # AMI MegaRAID
1152 device amrp # SCSI Passthrough interface (optional, CAM req.)
1154 device mfi # LSI MegaRAID SAS
1155 device mfip # LSI MegaRAID SAS passthrough, requires CAM
1159 # Areca RAID (CAM is required).
1161 device arcmsr # Areca SATA II RAID
1164 # Highpoint RocketRAID 182x.
1168 # Highpoint RocketRAID. Supports RR172x, RR222x, RR2240, RR232x, RR2340,
1169 # RR2210, RR174x, RR2522, RR231x, RR230x.
1173 # Highpoint RocketRAID 27xx.
1177 # Highpoint RocketRaid 3xxx series SATA RAID
1183 device twe # 3ware ATA RAID
1184 device twa # 3ware 9000 series PATA/SATA RAID
1185 options TWA_DEBUG=10 # enable debug messages
1186 device tws # 3ware 9750 series SATA/SAS RAID
1189 # Promise Supertrack SX6000
1198 # AHCI driver, this will override NATA for AHCI devices,
1199 # both drivers may be included.
1203 # SiI3124/3132 driver
1207 # The 'NATA' driver supports all ATA and ATAPI devices.
1208 # You only need one "device nata" for it to find all
1209 # PCI ATA/ATAPI devices on modern machines.
1212 device natadisk # ATA disk drives
1213 device natapicd # ATAPI CD/DVD drives
1214 device natapifd # ATAPI floppy drives
1215 device natapist # ATAPI tape drives
1216 device natapicam # ATAPI CAM layer emulation
1217 device nataraid # support for ATA software RAID controllers
1218 device natausb # ATA-over-USB support
1220 # The following options are valid for the NATA driver:
1222 # ATA_STATIC_ID: controller numbering is static (like the old driver)
1223 # else the device numbers are dynamically allocated.
1224 options ATA_STATIC_ID
1226 # For older non-PCI systems, these are the lines to use:
1228 #device nata0 at isa? port IO_WD1 irq 14
1229 #device nata1 at isa? port IO_WD2 irq 15
1232 # Standard floppy disk controllers: `fdc' and `fd'
1234 device fdc0 at isa? port IO_FD1 irq 6 drq 2
1236 # FDC_DEBUG enables floppy debugging. Since the debug output is huge, you
1237 # gotta turn it actually on by setting the variable fd_debug with DDB,
1241 device fd0 at fdc0 drive 0
1242 device fd1 at fdc0 drive 1
1245 # sio: serial ports (see sio(4))
1247 device sio0 at isa? port IO_COM1 flags 0x10 irq 4
1250 # `flags' for serial drivers that support consoles (only for sio now):
1251 # 0x10 enable console support for this unit. The other console flags
1252 # are ignored unless this is set. Enabling console support does
1253 # not make the unit the preferred console - boot with -h or set
1254 # the 0x20 flag for that. Currently, at most one unit can have
1255 # console support; the first one (in config file order) with
1256 # this flag set is preferred. Setting this flag for sio0 gives
1257 # the old behaviour.
1258 # 0x20 force this unit to be the console (unless there is another
1259 # higher priority console). This replaces the COMCONSOLE option.
1260 # 0x40 reserve this unit for low level console operations. Do not
1261 # access the device in any normal way.
1262 # 0x80 use this port for serial line gdb support in ddb.
1264 # PnP `flags' (set via userconfig using pnp x flags y)
1265 # 0x1 disable probing of this device. Used to prevent your modem
1266 # from being attached as a PnP modem.
1269 # Options for serial drivers that support consoles (only for sio now):
1270 options BREAK_TO_DEBUGGER #a BREAK on a comconsole goes to
1272 options CONSPEED=115200 # speed for serial console
1275 # Solaris implements a new BREAK which is initiated by a character
1276 # sequence CR ~ ^b which is similar to a familiar pattern used on
1277 # Sun servers by the Remote Console.
1278 options ALT_BREAK_TO_DEBUGGER
1281 options COM_ESP #code for Hayes ESP
1282 options COM_MULTIPORT #code for some cards with shared IRQs
1284 # Other flags for sio that aren't documented in the man page.
1285 # 0x20000 enable hardware RTS/CTS and larger FIFOs. Only works for
1286 # ST16650A-compatible UARTs.
1288 # PCI Universal Communications driver
1289 # Supports various single and multi port PCI serial cards. Maybe later
1290 # also the parallel ports on combination serial/parallel cards. New cards
1291 # can be added in src/sys/dev/misc/puc/pucdata.c.
1295 # Network interfaces: `ed', `ep', `is', `lnc'
1297 # ar: Arnet SYNC/570i hdlc sync 2/4 port V.35/X.21 serial driver (requires sppp)
1298 # cs: IBM Etherjet and other Crystal Semi CS89x0-based adapters
1299 # ed: Western Digital and SMC 80xx; Novell NE1000 and NE2000; 3Com 3C503
1301 # ex: Intel EtherExpress Pro/10 and other i82595-based adapters
1302 # fe: Fujitsu MB86960A/MB86965A Ethernet
1303 # lnc: Lance/PCnet cards (Isolan, Novell NE2100, NE32-VL, AMD Am7990 & Am79C960)
1304 # sbni: Granch SBNI12-xx adapters
1305 # sbsh: Granch SBNI16 SHDSL modem PCI adapters
1306 # sr: RISCom/N2 hdlc sync 1/2 port V.35/X.21 serial driver (requires sppp)
1307 # wi: Lucent WaveLAN/IEEE 802.11 PCMCIA adapters. Note: this supports both
1308 # the PCMCIA and ISA cards: the ISA card is really a PCMCIA to ISA
1309 # bridge with a PCMCIA adapter plugged into it.
1310 # an: Aironet 4500/4800 802.11 wireless adapters. Supports the PCMCIA,
1311 # PCI and ISA varieties.
1312 # xe: Xircom/Intel EtherExpress Pro100/16 PC Card ethernet controller.
1314 device ar0 at isa? port 0x300 irq 10 iomem 0xd0000
1315 device cs0 at isa? port 0x300
1316 device ed0 at isa? port 0x280 irq 5 iomem 0xd8000
1319 device fe0 at isa? port 0x300
1320 device lnc0 at isa? port 0x280 irq 10 drq 0
1321 device sbni0 at isa? port 0x210 irq 5 flags 0xefdead
1324 device sn0 at isa? port 0x300 irq 10
1326 # Wlan support is mandatory for some wireless LAN devices.
1327 options IEEE80211_DEBUG #enable debugging msgs
1328 options IEEE80211_AMPDU_AGE #age frames in AMPDU reorder q's
1329 options IEEE80211_SUPPORT_MESH #enable 802.11s D3.0 support
1330 options IEEE80211_SUPPORT_TDMA #enable TDMA support
1331 device wlan # 802.11 support
1332 device wlan_acl # 802.11 MAC-based access control for AP
1333 device wlan_ccmp # 802.11 CCMP support
1334 device wlan_tkip # 802.11 TKIP support
1335 device wlan_wep # 802.11 WEP support
1336 device wlan_xauth # 802.11 WPA or 802.1x authentication for AP
1337 device wlan_amrr # 802.11 AMRR TX rate control algorithm
1338 device an # Aironet Communications 4500/4800
1339 device ath # Atheros AR521x
1340 options AH_SUPPORT_AR5416
1341 device ath_hal # Atheros Hardware Access Layer
1342 #device ath_rate_amrr # Atheros AMRR TX rate control algorithm
1343 #device ath_rate_onoe # Atheros Onoe TX rate control algorithm
1344 device ath_rate_sample # Atheros Sample TX rate control algorithm
1345 options ATH_DEBUG # turn on debugging output (see hw.ath.debug)
1346 options ATH_DIAGAPI # diagnostic interface to the HAL
1347 options ATH_RXBUF=80 # number of RX buffers to allocate
1348 options ATH_TXBUF=400 # number of TX buffers to allocate
1349 #device iwl # Intel PRO/Wireless 2100
1350 device iwi # Intel PRO/Wireless 2200BG/2915ABG
1351 device iwn # Intel WiFi Link 4965/1000/5000/5150/5300/6000/6050
1352 options IWN_DEBUG # turn on debugging output
1353 device wi # WaveLAN/IEEE, PRISM-II, Spectrum24 802.11DS
1354 #device rtw # RealTek 8180
1355 #device acx # TI ACX100/ACX111.
1356 device xe # Xircom PCMCIA
1357 device ral # Ralink Technology 802.11 wireless NIC
1360 # IEEE 802.11 adapter firmware modules
1362 # iwifw: Intel PRO/Wireless 2200BG/2225BG/2915ABG firmware
1363 # iwnfw: Intel WiFi Link 4965/1000/5000/5150/5300/6000/6050
1364 # ralfw: Ralink Technology RT25xx and RT26xx firmware
1365 # wpifw: Intel 3945ABG Wireless LAN Controller firmware
1372 # Bluetooth Protocols
1376 # ATM related options
1378 # The `en' device provides support for Efficient Networks (ENI)
1379 # ENI-155 PCI midway cards, and the Adaptec 155Mbps PCI ATM cards (ANA-59x0).
1381 # atm pseudo-device provides generic atm functions and is required for
1383 # NATM enables the netnatm protocol family that can be used to
1386 # the current driver supports only PVC operations (no atm-arp, no multicast).
1387 # for more details, please read the original documents at
1388 # http://www.ccrc.wustl.edu/pub/chuck/tech/bsdatm/bsdatm.html
1392 options NATM #native ATM
1397 # Basic sound card support:
1399 # For PCI sound cards:
1400 device "snd_als4000"
1406 device "snd_emu10k1"
1408 device "snd_envy24ht"
1413 device "snd_maestro"
1414 device "snd_maestro3"
1415 device "snd_neomagic"
1418 device "snd_t4dwave"
1419 device "snd_via8233"
1420 device "snd_via82c686"
1426 # Miscellaneous hardware:
1428 # apm: Laptop Advanced Power Management (experimental)
1429 # bktr: Brooktree bt848/848a/849a/878/879 video capture and TV Tuner board
1430 # cy: Cyclades serial driver
1431 # ecc: ECC memory controller
1433 # nrp: Comtrol Rocketport
1434 # si: Specialix SI/XIO 4-32 port terminal multiplexor
1435 # spic: Sony Programmable I/O controller (VAIO notebooks)
1436 # stl: Stallion EasyIO and EasyConnection 8/32 (PCI), EasyConnection 8/64 PCI
1437 # nmdm: nullmodem terminal driver (see nmdm(4))
1438 # tpm: Trusted Platform Module
1441 # The flags takes the following meaning for apm0:
1442 # 0x0020 Statclock is broken.
1443 # If apm is omitted, some systems require sysctl -w kern.timecounter.method=1
1444 # for correct timekeeping.
1446 # Notes on the Specialix SI/XIO driver:
1447 # **This is NOT a Specialix supported Driver!**
1448 # The host card is memory, not IO mapped.
1449 # The Rev 1 host cards use a 64K chunk, on a 32K boundary.
1450 # The Rev 2 host cards use a 32K chunk, on a 32K boundary.
1451 # The cards can use an IRQ of 11, 12 or 15.
1453 # Notes on the Stallion stl driver:
1454 # This is version 2.0.0, unsupported by Stallion.
1458 device joy0 at isa? port IO_GAME
1461 device si0 at isa? iomem 0xd0000 irq 12
1462 device spic0 at isa? irq 0 port 0x10a0
1464 # nullmodem terminal driver
1468 # The `ahc' device provides support for the Adaptec 274X and 284X
1472 # The aic7xxx driver will attempt to use memory mapped I/O for all PCI
1473 # controllers that have it configured only if this option is set. Unfortunately,
1474 # this doesn't work on some motherboards, which prevents it from being the
1476 options AHC_ALLOW_MEMIO
1478 # The adw driver will attempt to use memory mapped I/O for all PCI
1479 # controllers that have it configured only if this option is set.
1480 options ADW_ALLOW_MEMIO
1483 # PCI devices & PCI options:
1485 # The main PCI bus device is `pci'. It provides auto-detection and
1486 # configuration support for all devices on the PCI bus, using either
1487 # configuration mode defined in the PCI specification.
1493 options COMPAT_OLDPCI #FreeBSD 2.2 and 3.x compatibility shims
1504 # The `ahc' device provides support for the Adaptec 29/3940(U)(W)
1505 # and motherboard based AIC7870/AIC7880 adapters.
1507 options AHC_DEBUG_OPTS=0xffffffff
1508 options AHC_REG_PRETTY_PRINT
1509 options AHC_TMODE_ENABLE
1511 # The 'ahd' device provides support for the Adaptec 79xx Ultra320
1512 # SCSI adapters. Options are documented in the ahd(4) manpage:
1514 options AHD_DEBUG_OPTS=0xffffffff
1515 options AHD_REG_PRETTY_PRINT
1516 #options AHD_TMODE_ENABLE=0xff
1518 # The `amd' device provides support for the AMD 53C974 SCSI host
1519 # adapter chip as found on devices such as the Tekram DC-390(T).
1521 # The `bge' device provides support for gigabit ethernet adapters
1522 # based on the Broadcom BCM570x family of controllers, including the
1523 # 3Com 3c996-T, the Netgear GA302T, the SysKonnect SK-9D21 and SK-9D41,
1524 # and the embedded gigE NICs on Dell PowerEdge 2550 servers.
1526 # The `ncr' device provides support for the NCR 53C810 and 53C825
1527 # self-contained SCSI host adapters.
1529 # The `isp' device provides support for the Qlogic ISP 1020, 1040
1530 # nd 1040B PCI SCSI host adapters, ISP 1240 Dual Ultra SCSI,
1531 # ISP 1080 and 1280 (Dual) Ultra2, ISP 12160 Ultra3 SCSI, as well as
1532 # the Qlogic ISP 2100 and ISP 2200 Fibre Channel Host Adapters.
1534 # The `dc' device provides support for PCI fast ethernet adapters
1535 # based on the DEC/Intel 21143 and various workalikes including:
1536 # the ADMtek AL981 Comet and AN985 Centaur, the ASIX Electronics
1537 # AX88140A and AX88141, the Davicom DM9100 and DM9102, the Lite-On
1538 # 82c168 and 82c169 PNIC, the Lite-On/Macronix LC82C115 PNIC II
1539 # and the Macronix 98713/98713A/98715/98715A/98725 PMAC. This driver
1540 # replaces the old al, ax, dm, pn and mx drivers. List of brands:
1541 # Digital DE500-BA, Kingston KNE100TX, D-Link DFE-570TX, SOHOware SFA110,
1542 # SVEC PN102-TX, CNet Pro110B, 120A, and 120B, Compex RL100-TX,
1543 # LinkSys LNE100TX, LNE100TX V2.0, Jaton XpressNet, Alfa Inc GFC2204,
1546 # The `de' device provides support for the Digital Equipment DC21040
1547 # self-contained Ethernet adapter.
1549 # The `em' device provides support for the Intel Pro/1000 Family of Gigabit
1550 # adapters (82542, 82543, 82544, 82540).
1552 # The `et' device provides support for the Agere ET1310 10/100/1000 PCIe
1555 # The `fxp' device provides support for the Intel EtherExpress Pro/100B
1556 # PCI Fast Ethernet adapters.
1558 # The 'lge' device provides support for PCI gigabit ethernet adapters
1559 # based on the Level 1 LXT1001 NetCellerator chipset. This includes the
1560 # D-Link DGE-500SX, SMC TigerCard 1000 (SMC9462SX), and some Addtron cards.
1562 # The 'my' device provides support for the Myson MTD80X and MTD89X PCI
1563 # Fast Ethernet adapters.
1565 # The 'nge' device provides support for PCI gigabit ethernet adapters
1566 # based on the National Semiconductor DP83820 and DP83821 chipset. This
1567 # includes the SMC EZ Card 1000 (SMC9462TX), D-Link DGE-500T, Asante
1568 # FriendlyNet GigaNIX 1000TA and 1000TPC, the Addtron AEG320T, the
1569 # LinkSys EG1032 and EG1064, the Surecom EP-320G-TX and the Netgear GA622T.
1571 # The 'oce' device provides support for Emulex 10 Gbit adapters
1572 # (OneConnect Ethernet).
1574 # The 'pcn' device provides support for PCI fast ethernet adapters based
1575 # on the AMD Am79c97x chipsets, including the PCnet/FAST, PCnet/FAST+,
1576 # PCnet/PRO and PCnet/Home. These were previously handled by the lnc
1577 # driver (and still will be if you leave this driver out of the kernel).
1579 # Te 're' device provides support for PCI GigaBit ethernet adapters based
1580 # on the RealTek 8169 chipset. It also supports the 8139C+ and is the
1581 # preferred driver for that chip.
1583 # The 'rl' device provides support for PCI fast ethernet adapters based
1584 # on the RealTek 8129/8139 chipset. Note that the RealTek driver defaults
1585 # to using programmed I/O to do register accesses because memory mapped
1586 # mode seems to cause severe lockups on SMP hardware. This driver also
1587 # supports the Accton EN1207D `Cheetah' adapter, which uses a chip called
1588 # the MPX 5030/5038, which is either a RealTek in disguise or a RealTek
1589 # workalike. Note that the D-Link DFE-530TX+ uses the RealTek chipset
1590 # and is supported by this driver, not the 'vr' driver.
1592 # The 'sf' device provides support for Adaptec Duralink PCI fast
1593 # ethernet adapters based on the Adaptec AIC-6915 "starfire" controller.
1594 # This includes dual and quad port cards, as well as one 100baseFX card.
1595 # Most of these are 64-bit PCI devices, except for one single port
1596 # card which is 32-bit.
1598 # The 'ste' device provides support for adapters based on the Sundance
1599 # Technologies ST201 PCI fast ethernet controller. This includes the
1602 # The 'sis' device provides support for adapters based on the Silicon
1603 # Integrated Systems SiS 900 and SiS 7016 PCI fast ethernet controller
1606 # The 'sk' device provides support for the SysKonnect SK-984x series
1607 # PCI gigabit ethernet NICs. This includes the SK-9841 and SK-9842
1608 # single port cards (single mode and multimode fiber) and the
1609 # SK-9843 and SK-9844 dual port cards (also single mode and multimode).
1610 # The driver will autodetect the number of ports on the card and
1611 # attach each one as a separate network interface.
1613 # The 'ti' device provides support for PCI gigabit ethernet NICs based
1614 # on the Alteon Networks Tigon 1 and Tigon 2 chipsets. This includes the
1615 # Alteon AceNIC, the 3Com 3c985, the Netgear GA620 and various others.
1616 # Note that you will probably want to bump up NMBCLUSTERS a lot to use
1619 # The 'tl' device provides support for the Texas Instruments TNETE100
1620 # series 'ThunderLAN' cards and integrated ethernet controllers. This
1621 # includes several Compaq Netelligent 10/100 cards and the built-in
1622 # ethernet controllers in several Compaq Prosignia, Proliant and
1623 # Deskpro systems. It also supports several Olicom 10Mbps and 10/100
1626 # The `tx' device provides support for the SMC 9432 TX, BTX and FTX cards.
1628 # The `txp' device provides support for the 3Com 3cR990 "Typhoon"
1631 # The `vr' device provides support for various fast ethernet adapters
1632 # based on the VIA Technologies VT3043 `Rhine I' and VT86C100A `Rhine II'
1633 # chips, including the D-Link DFE530TX (see 'rl' for DFE530TX+), the Hawking
1634 # Technologies PN102TX, and the AOpen/Acer ALN-320.
1636 # The `vx' device provides support for the 3Com 3C590 and 3C595
1639 # The `wb' device provides support for various fast ethernet adapters
1640 # based on the Winbond W89C840F chip. Note: this is not the same as
1641 # the Winbond W89C940F, which is an NE2000 clone.
1643 # The `xl' device provides support for the 3Com 3c900, 3c905 and
1644 # 3c905B (Fast) Etherlink XL cards and integrated controllers. This
1645 # includes the integrated 3c905B-TX chips in certain Dell Optiplex and
1646 # Dell Precision desktop machines and the integrated 3c905-TX chips
1647 # in Dell Latitude laptop docking stations.
1649 # The 'bktr' device is a PCI video capture device using the Brooktree
1650 # bt848/bt848a/bt849a/bt878/bt879 chipset. When used with a TV Tuner it forms a
1651 # TV card, eg Miro PC/TV, Hauppauge WinCast/TV WinTV, VideoLogic Captivator,
1652 # Intel Smart Video III, AverMedia, IMS Turbo, FlyVideo.
1654 # options OVERRIDE_CARD=xxx
1655 # options OVERRIDE_TUNER=xxx
1656 # options OVERRIDE_MSP=1
1657 # options OVERRIDE_DBX=1
1658 # These options can be used to override the auto detection
1659 # The current values for xxx are found in src/sys/dev/video/bktr/bktr_card.h
1660 # Using sysctl(8) run-time overrides on a per-card basis can be made
1662 # options BKTR_SYSTEM_DEFAULT=BROOKTREE_PAL
1664 # options BKTR_SYSTEM_DEFAULT=BROOKTREE_NTSC
1665 # Specifies the default video capture mode.
1666 # This is required for Dual Crystal (28&35Mhz) boards where PAL is used
1667 # to prevent hangs during initialisation. eg VideoLogic Captivator PCI.
1669 # options BKTR_USE_PLL
1670 # PAL or SECAM users who have a 28Mhz crystal (and no 35Mhz crystal)
1671 # must enable PLL mode with this option. eg some new Bt878 cards.
1673 # options BKTR_GPIO_ACCESS
1674 # This enable IOCTLs which give user level access to the GPIO port.
1676 # options BKTR_NO_MSP_RESET
1677 # Prevents the MSP34xx reset. Good if you initialise the MSP in another OS first
1679 # options BKTR_430_FX_MODE
1680 # Switch Bt878/879 cards into Intel 430FX chipset compatibility mode.
1682 # options BKTR_SIS_VIA_MODE
1683 # Switch Bt878/879 cards into SIS/VIA chipset compatibility mode which is
1684 # needed for some old SiS and VIA chipset motherboards.
1685 # This also allows Bt878/879 chips to work on old OPTi (<1997) chipset
1686 # motherboards and motherboards with bad or incomplete PCI 2.1 support.
1687 # As a rough guess, old = before 1998
1689 # options BKTR_NEW_MSP34XX_DRIVER
1690 # Use new, more complete initialization scheme for the msp34* soundchip.
1691 # Should fix stereo autodetection if the old driver does only output
1694 # options BKTR_OVERRIDE_CARD=xxx
1695 # options BKTR_OVERRIDE_DBX=xxx
1696 # options BKTR_OVERRIDE_MSP=xxx
1697 # options BKTR_OVERRIDE_TUNER=xxx
1698 # These options can be used to select a specific device, regardless of
1699 # the autodetection and i2c device checks (see comments in bktr_card.c).
1701 device ahc # AHA2940 and onboard AIC7xxx devices
1702 device ahd # AIC79xx devices
1703 device amd # AMD 53C974 (Tekram DC-390(T))
1704 device isp # Qlogic family
1705 device ispfw # Firmware for QLogic HBAs
1706 device mpt # LSI '909 FC adapters
1707 device mps # LSI-Logic MPT-Fusion 2
1708 device ncr # NCR/Symbios Logic
1709 device sym # NCR/Symbios Logic (newer chipsets)
1710 device trm # Tekram DC395U/UW/F and DC315U
1714 # ISP_TARGET_MODE - enable target mode operation
1715 #options ISP_TARGET_MODE=1
1717 # Options used in dev/disk/sym/ (Symbios SCSI driver).
1718 #options SYM_SETUP_LP_PROBE_MAP #-Low Priority Probe Map (bits)
1719 # Allows the ncr to take precedence
1720 # 1 (1<<0) -> 810a, 860
1721 # 2 (1<<1) -> 825a, 875, 885, 895
1722 # 4 (1<<2) -> 895a, 896, 1510d
1723 #options SYM_SETUP_SCSI_DIFF #-HVD support for 825a, 875, 885
1724 # disabled:0 (default), enabled:1
1725 #options SYM_SETUP_PCI_PARITY #-PCI parity checking
1726 # disabled:0, enabled:1 (default)
1727 #options SYM_SETUP_MAX_LUN #-Number of LUNs supported
1728 # default:8, range:[1..64]
1731 # MII bus support is required for some PCI 10/100 ethernet NICs,
1732 # namely those which use MII-compliant transceivers or implement
1733 # transceiver control interfaces that operate like an MII. Adding
1734 # "device miibus0" to the kernel config pulls in support for
1735 # the generic miibus API and all of the PHY drivers, including a
1736 # generic one for PHYs that aren't specifically handled by an
1737 # individual driver.
1740 # PCI Ethernet NICs that use the common MII bus controller code.
1741 device ae # Attansic/Atheros L2 Fast Ethernet
1742 device alc # Atheros AR8131/AR8132
1743 device ale # Atheros AR8121/AR8113/AR8114
1744 device age # Attansic/Atheros L1 Gigabit Ethernet
1745 device bce # Broadcom NetXtreme II Gigabit Ethernet
1746 device bfe # Broadcom BCM440x 10/100 Ethernet
1747 device bnx # Broadcom NetXtreme 5718/57785 Gigabit Ethernet
1748 device dc # DEC/Intel 21143 and various workalikes
1749 device fxp # Intel EtherExpress PRO/100B (82557, 82558)
1750 device my # Myson Fast Ethernet (MTD80X, MTD89X)
1751 device pcn # AMD Am79C97x PCI 10/100 NICs
1752 device re # RealTek 8139C+/8169
1753 device rl # RealTek 8129/8139
1754 device sbsh # Granch SBNI16 SHDSL modem
1755 device sf # Adaptec AIC-6915 (``Starfire'')
1756 device sis # Silicon Integrated Systems SiS 900/SiS 7016
1757 device ste # Sundance ST201 (D-Link DFE-550TX)
1758 device tl # Texas Instruments ThunderLAN
1759 device tx # SMC EtherPower II (83c17x ``EPIC'')
1760 device vge # VIA 612x GigE
1761 device vr # VIA Rhine, Rhine II
1762 device wb # Winbond W89C840F
1763 device xl # 3Com 3c90x (``Boomerang'', ``Cyclone'')
1765 # PCI Ethernet NICs.
1766 device de # DEC/Intel DC21x4x (``Tulip'')
1767 device txp # 3Com 3cR990 (``Typhoon'')
1768 device vx # 3Com 3c590, 3c595 (``Vortex'')
1770 # Gigabit Ethernet NICs.
1771 device bge # Broadcom BCM570x (``Tigon III'')
1772 device em # Intel Pro/1000 (8254x,8257x)
1774 device emx # Intel Pro/1000 (8257{1,2,3,4})
1776 device igb # Intel Pro/1000 (82575, 82576, 82580, i350)
1778 device ig_hal # Intel Pro/1000 hardware abstraction layer
1779 device ixgbe # Intel PRO/10GbE PCIE Ethernet Family
1780 device et # Agere ET1310 10/100/1000 Ethernet
1781 device lge # Level 1 LXT1001 (``Mercury'')
1782 device mxge # Myricom Myri-10G 10GbE NIC
1783 device nfe # nVidia nForce2/3 MCP04/51/55 CK804
1784 device nge # NatSemi DP83820 and DP83821
1785 device oce # Emulex 10 GbE (OneConnect Ethernet)
1786 device sk # SysKonnect GEnesis, LinkSys EG1023, D-Link
1787 device ti # Alteon (``Tigon I'', ``Tigon II'')
1788 device stge # Sundance/Tamarack TC9021 Gigabit Ethernet
1789 device msk # Marvell/SysKonnect Yukon II Gigabit Ethernet
1790 device jme # JMicron Gigabit/Fast Ethernet
1792 # Brooktree driver has been ported to the new I2C framework. Thus,
1793 # you'll need to have the following 3 lines in the kernel config.
1797 # The iic and smb devices are only needed if you want to control other
1798 # I2C slaves connected to the external connector of some cards.
1801 options BKTR_NEW_MSP34XX_DRIVER
1803 # WinTV PVR-250/350 driver
1809 # pccard: pccard slots
1810 # cardbus/cbb: cardbus bridge
1816 # Laptop/Notebook options:
1819 # apm under `Miscellaneous hardware'
1822 # For older notebooks that signal a powerfail condition (external
1823 # power supply dropped, or battery state low) by issuing an NMI:
1825 options POWERFAIL_NMI # make it beep instead of panicing
1831 # mmcsd MMC/SD memory card
1832 # sdhci Generic PCI SD Host Controller
1841 # System Management Bus support is provided by the 'smbus' device.
1842 # Access to the SMBus device is via the 'smb' device (/dev/smb*),
1843 # which is a child of the 'smbus' device.
1845 # Supported devices:
1846 # smb standard io through /dev/smb*
1848 # Supported SMB interfaces:
1849 # iicsmb I2C to SMB bridge with any iicbus interface
1850 # bktr brooktree848 I2C hardware interface
1851 # intpm Intel PIIX4 (82371AB, 82443MX) Power Management Unit
1852 # alpm Acer Aladdin-IV/V/Pro2 Power Management Unit
1853 # ichsmb Intel ICH SMBus controller chips (82801AA, 82801AB, 82801BA)
1854 # viapm VIA VT82C586B,596,686A and VT8233 SMBus controllers
1855 # amdpm AMD 756 Power Management Unit
1856 # amdsmb AMD 8111 SMBus 2.0 Controller
1858 device smbus # Bus support, required for smb below.
1872 # Philips i2c bus support is provided by the `iicbus' device.
1874 # Supported devices:
1875 # ic i2c network interface
1876 # iic i2c standard io
1877 # iicsmb i2c to smb bridge. Allow i2c i/o with smb commands.
1879 # Supported interfaces:
1880 # pcf Philips PCF8584 ISA-bus controller
1881 # bktr brooktree848 I2C software interface
1884 # iicbb generic I2C bit-banging code (needed by lpbb, bktr)
1886 device iicbus # Bus support, required for ic/iic/iicsmb below.
1891 device iicsmb # smb over i2c bridge
1893 device pcf0 at isa? port 0x320 irq 5
1895 # Intel Core and newer CPUs on-die digital thermal sensor support
1898 # AMD Family 0Fh, 10h and 11h temperature sensors
1902 # ThinkPad Active Protection System accelerometer
1903 device aps0 at isa? port 0x1600
1905 # HW monitoring devices lm(4), it(4) and nsclpcsio.
1906 device lm0 at isa? port 0x290
1907 device it0 at isa? port 0x290
1908 device it1 at isa? port 0xc00
1909 device it2 at isa? port 0xd00
1910 device it3 at isa? port 0x228
1911 device nsclpcsio0 at isa? port 0x2e
1912 device nsclpcsio1 at isa? port 0x4e
1913 device wbsio0 at isa? port 0x2e
1914 device wbsio1 at isa? port 0x4e
1915 device lm#3 at wbsio?
1916 device uguru0 at isa? port 0xe0 # ABIT uGuru
1920 # Parallel port bus support is provided by the `ppbus' device.
1921 # Multiple devices may be attached to the parallel port, devices
1922 # are automatically probed and attached when found.
1924 # Supported devices:
1925 # vpo Iomega Zip Drive
1926 # Requires SCSI disk support ('scbus' and 'da'); the best
1927 # performance is achieved with ports in EPP 1.9 mode.
1928 # lpt Parallel Printer
1929 # plip Parallel network interface
1930 # ppi General-purpose I/O ("Geek Port") + IEEE1284 I/O
1931 # pps Pulse per second Timing Interface
1932 # lpbb Philips official parallel port I2C bit-banging interface
1934 # Supported interfaces:
1935 # ppc ISA-bus parallel port interfaces.
1938 options PPC_PROBE_CHIPSET # Enable chipset specific detection
1939 # (see flags in ppc(4))
1940 options DEBUG_1284 # IEEE1284 signaling protocol debug
1941 options PERIPH_1284 # Makes your computer act as a IEEE1284
1942 # compliant peripheral
1943 options DONTPROBE_1284 # Avoid boot detection of PnP parallel devices
1944 options VP0_DEBUG # ZIP/ZIP+ debug
1945 options LPT_DEBUG # Printer driver debug
1946 options PPC_DEBUG=2 # Parallel chipset level debug
1947 options PLIP_DEBUG # Parallel network IP interface debug
1948 options PCFCLOCK_VERBOSE # Verbose pcfclock driver
1949 options PCFCLOCK_MAX_RETRIES=5 # Maximum read tries (default 10)
1951 device ppc0 at isa? irq 7
1961 # Kernel BOOTP support
1963 options BOOTP # Use BOOTP to obtain IP address/hostname
1964 options BOOTP_NFSROOT # NFS mount root filesystem using BOOTP info
1965 options BOOTP_NFSV3 # Use NFS v3 to NFS mount root
1966 options BOOTP_COMPAT # Workaround for broken bootp daemons.
1967 options BOOTP_WIRED_TO=fxp0 # Use interface fxp0 for BOOTP
1970 # Set the number of PV entries per process. Increasing this can
1971 # stop panics related to heavy use of shared memory. However, that can
1972 # (combined with large amounts of physical memory) cause panics at
1973 # boot time due the kernel running out of VM space.
1975 # If you're tweaking this, you might also want to increase the sysctls
1976 # "vm.v_free_min", "vm.v_free_reserved", and "vm.v_free_target".
1978 # The value below is the one more than the default.
1980 options PMAP_SHPGPERPROC=201
1983 # Change the size of the kernel virtual address space. Due to
1984 # constraints in loader(8) on i386, this must be a multiple of 4.
1985 # 256 = 1 GB of kernel address space. Increasing this also causes
1986 # a reduction of the address space in user processes. 512 splits
1987 # the 4GB cpu address space in half (2GB user, 2GB kernel).
1989 options KVA_PAGES=260
1992 # Disable swapping. This option removes all code which actually performs
1993 # swapping, so it's not possible to turn it back on at run-time.
1995 # This is sometimes usable for systems which don't have any swap space
1996 # (see also sysctls "vm.defer_swapspace_pageouts" and
1997 # "vm.disable_swapspace_pageouts")
1999 #options NO_SWAPPING
2001 # Set the size of the buffer cache KVM reservation, in buffers. This is
2002 # scaled by approximately 16384 bytes. The system will auto-size the buffer
2003 # cache if this option is not specified.
2007 # Set the size of the mbuf KVM reservation, in clusters. This is scaled
2008 # by approximately 2048 bytes. The system will auto-size the mbuf area
2009 # to (512 + maxusers*16) if this option is not specified.
2010 # maxusers is in turn computed at boot time depending on available memory
2011 # or set to the value specified by "options MAXUSERS=x" (x=0 means
2013 # So, to take advantage of autoscaling, you have to remove both
2014 # NMBCLUSTERS and MAXUSERS (and NMBUFS) from your kernel config.
2016 options NMBCLUSTERS=1024
2018 # Set the number of mbufs available in the system. Each mbuf
2019 # consumes 256 bytes. The system will autosize this (to 4 times
2020 # the number of NMBCLUSTERS, depending on other constraints)
2021 # if this option is not specified.
2025 # Tune the buffer cache maximum KVA reservation, in bytes. The maximum is
2026 # usually capped at 200 MB, effecting machines with > 1GB of ram. Note
2027 # that the buffer cache only really governs write buffering and disk block
2028 # translations. The VM page cache is our primary disk cache and is not
2029 # effected by the size of the buffer cache.
2031 options VM_BCACHE_SIZE_MAX="(100*1024*1024)"
2033 # Tune the swap zone KVA reservation, in bytes. The default is typically
2034 # 70 MB, giving the system the ability to manage a maximum of 28GB worth
2035 # of swapped out data.
2037 options VM_SWZONE_SIZE_MAX="(50*1024*1024)"
2040 # Enable extra debugging code for locks. This stores the filename and
2041 # line of whatever acquired the lock in the lock itself, and change a
2042 # number of function calls to pass around the relevant data. This is
2043 # not at all useful unless you are debugging lock code. Also note
2044 # that it is likely to break e.g. fstat(1) unless you recompile your
2045 # userland with -DDEBUG_LOCKS as well.
2047 # DEBUG_LOCKS_LATENCY adds a sysctl to add a forced latency loop
2048 # (count to N) in front of any spinlock or gettoken.
2051 options DEBUG_LOCKS_LATENCY
2053 # Set the amount of time (in seconds) the system will wait before
2054 # rebooting automatically when a kernel panic occurs. If set to (-1),
2055 # the system will wait indefinitely until a key is pressed on the
2057 options PANIC_REBOOT_WAIT_TIME=16
2059 # Attempt to bypass the buffer cache and put data directly into the
2060 # userland buffer for read operation when O_DIRECT flag is set on the
2061 # file. Both offset and length of the read operation must be
2062 # multiples of the physical media sector size.
2066 # Specify a lower limit for the number of swap I/O buffers. They are
2067 # (among other things) used when bypassing the buffer cache due to
2068 # DIRECTIO kernel option enabled and O_DIRECT flag set on file.
2070 #options NSWBUF_MIN=120
2072 # The 'asr' driver provides support for current DPT/Adaptec SCSI RAID
2073 # controllers (SmartRAID V and VI and later).
2074 # These controllers require the CAM infrastructure.
2079 # The 'dpt' driver provides support for DPT controllers (http://www.dpt.com/).
2080 # These have hardware RAID-{0,1,5} support, and do multi-initiator I/O.
2081 # The DPT controllers are commonly re-licensed under other brand-names -
2082 # some controllers by Olivetti, Dec, HP, AT&T, SNI, AST, Alphatronic, NEC and
2083 # Compaq are actually DPT controllers.
2085 # See src/sys/dev/raid/dpt for debugging and other subtle options.
2086 # DPT_MEASURE_PERFORMANCE Enables a set of (semi)invasive metrics. Various
2087 # instruments are enabled. The tools in
2088 # /usr/sbin/dpt_* assume these to be enabled.
2089 # DPT_HANDLE_TIMEOUTS Normally device timeouts are handled by the DPT.
2090 # If you ant the driver to handle timeouts, enable
2091 # this option. If your system is very busy, this
2092 # option will create more trouble than solve.
2093 # DPT_TIMEOUT_FACTOR Used to compute the excessive amount of time to
2094 # wait when timing out with the above option.
2095 # DPT_DEBUG_xxxx These are controllable from sys/dev/raid/dpt/dpt.h
2096 # DPT_LOST_IRQ When enabled, will try, once per second, to catch
2097 # any interrupt that got lost. Seems to help in some
2098 # DPT-firmware/Motherboard combinations. Minimal
2099 # cost, great benefit.
2100 # DPT_RESET_HBA Make "reset" actually reset the controller
2101 # instead of fudging it. Only enable this if you
2102 # are 100% certain you need it.
2107 #!CAM# options DPT_MEASURE_PERFORMANCE
2108 #!CAM# options DPT_HANDLE_TIMEOUTS
2109 options DPT_TIMEOUT_FACTOR=4
2110 options DPT_LOST_IRQ
2111 options DPT_RESET_HBA
2114 # Compaq "CISS" RAID controllers (SmartRAID 5* series)
2115 # These controllers have a SCSI-like interface, and require the
2116 # CAM infrastructure.
2121 # Intel Integrated RAID controllers.
2122 # This driver is supported and maintained by
2123 # "Leubner, Achim" <Achim_Leubner@adaptec.com>.
2128 # Mylex AcceleRAID and eXtremeRAID controllers with v6 and later
2129 # firmware. These controllers have a SCSI-like interface, and require
2130 # the CAM infrastructure.
2141 # General USB code (mandatory for USB)
2143 # Use this instead of usb for the new stack
2150 # Generic USB device driver
2152 # Human Interface Device (anything with buttons and dials)
2158 # USB Iomega Zip 100 Drive (Requires scbus and da)
2164 # USB Rio (MP3 Player)
2184 # ADMtek USB ethernet. Supports the LinkSys USB100TX,
2185 # the Billionton USB100, the Melco LU-ATX, the D-Link DSB-650TX
2186 # and the SMC 2202USB. Also works with the ADMtek AN986 Pegasus
2190 # ASIX Electronics AX88172 USB 2.0 ethernet driver. Used in the
2191 # LinkSys USB200M and various other adapters.
2194 # CATC USB-EL1201A USB ethernet. Supports the CATC Netmate
2195 # and Netmate II, and the Belkin F5U111.
2198 # Kawasaki LSI ethernet. Supports the LinkSys USB10T,
2199 # Entrega USB-NET-E45, Peracom Ethernet Adapter, the
2200 # 3Com 3c19250, the ADS Technologies USB-10BT, the ATen UC10T,
2201 # the Netgear EA101, the D-Link DSB-650, the SMC 2102USB
2202 # and 2104USB, and the Corega USB-T.
2205 # USB CDC ethernet. Supports the LG P-500 smartphone.
2208 # RealTek 8150 based USB ethernet device:
2210 # GREEN HOUSE GH-USB100B
2211 # Billionton ThumbLAN USBKR2-100B
2214 # USB wireless NICs, requires wlan_amrr
2216 # Ralink Technology RT2501USB/RT2601USB
2219 # Ralink Technology RT2700U/RT2800U/RT3000U wireless driver
2223 # Ralink Technology RT2500USB
2226 # Realtek RTL8188CU/RTL8192CU wireless driver
2230 # debugging options for the USB subsystem
2235 options UKBD_DFLT_KEYMAP # specify the built-in keymap
2236 makeoptions UKBD_DFLT_KEYMAP=it.iso
2239 device firewire # Firewire bus code
2240 device sbp # SCSI over Firewire (Requires scbus and da)
2241 device fwe # Ethernet over Firewire (non-standard!)
2243 # dcons support (Dumb Console Device)
2244 device dcons # dumb console driver
2245 device dcons_crom # FireWire attachment
2246 options DCONS_BUF_SIZE=16384 # buffer size
2247 options DCONS_POLL_HZ=100 # polling rate
2248 options DCONS_FORCE_CONSOLE=1 # force to be the primary console
2249 options DCONS_FORCE_GDB=1 # force to be the gdb device
2251 #####################################################################
2254 # This is a port of the openbsd crypto framework. Include this when
2255 # configuring IPsec and when you have a h/w crypto device to accelerate
2256 # user applications that link to openssl.
2258 # Drivers are ports from openbsd with some simple enhancements that have
2259 # been fed back to openbsd (and hopefully will be included).
2261 pseudo-device crypto # core crypto support
2262 pseudo-device cryptodev # /dev/crypto for access to h/w
2264 device rndtest # FIPS 140-2 entropy tester
2266 device hifn # Hifn 7951, 7781, etc.
2267 options HIFN_DEBUG # enable debugging support: hw.hifn.debug
2268 #options HIFN_NO_RNG # for devices without RNG
2269 options HIFN_RNDTEST # enable rndtest support
2271 device safe # SafeNet 1141
2272 options SAFE_DEBUG # enable debugging support: hw.safe.debug
2273 #options SAFE_NO_RNG # for devices without RNG
2274 options SAFE_RNDTEST # enable rndtest support
2276 device ubsec # Broadcom 5501, 5601, 58xx
2277 options UBSEC_DEBUG # enable debugging support: hw.ubsec.debug
2278 #options UBSEC_NO_RNG # for devices without RNG
2279 options UBSEC_RNDTEST # enable rndtest support
2281 device aesni # hardware crypto/RNG for AES-NI
2282 device glxsb # Geode LX Security Block
2283 device padlock # hardware crypto/RNG for VIA C3/C7/Eden
2284 device rdrand # hardware RNG for RdRand
2287 # ACPI support using the Intel ACPI Component Architecture reference
2290 # ACPI_DEBUG enables the use of the debug.acpi.level and debug.acpi.layer
2291 # kernel environment variables to select initial debugging levels for the
2292 # Intel ACPICA code.
2294 # Note that building ACPI into the kernel is deprecated; the module is
2295 # normally loaded automatically by the loader.
2300 # ACPI WMI Mapping driver
2303 # ACPI Asus Extras (LCD backlight/brightness, video output, etc.)
2306 # ACPI Fujitsu Extras (Buttons)
2309 # ACPI extras driver for HP laptops
2312 # ACPI Panasonic Extras (LCD backlight/brightness, video output, etc.)
2313 device acpi_panasonic
2315 # ACPI Sony extra (LCD brightness)
2318 # ACPI extras driver for ThinkPad laptops
2319 device acpi_thinkpad
2321 # ACPI Toshiba Extras (LCD backlight/brightness, video output, etc.)
2324 # ACPI Video Extensions (LCD backlight/brightness, video output, etc.)
2327 device aibs # ASUSTeK AI Booster (ACPI ASOC ATK0110)
2328 device pmtimer # adjust the system clock after resume
2331 # drm: General DRM code
2332 # i915kmsdrm: Intel integrated GPUs, starting from the 830M family
2333 # mach64drm: ATI Mach64 cards - Rage and 3D Rage series
2334 # mgadrm: AGP Matrox G200, G400, G450, G550
2335 # r128drm: ATI Rage 128 cards
2336 # radeonkmsdrm: ATI Radeon cards
2337 # savagedrm: Savage cards
2339 # tdfxdrm: 3dfx Voodoo 3/4/5 and Banshee
2341 # DRM_DEBUG: include debug printfs, very slow
2343 # DRM requires AGP in the kernel.
2346 #device "i915kmsdrm" # breaks VGA console, disabled by default
2350 #device radeonkmsdrm # breaks VGA console, disabled by default
2361 device cmx # Omnikey CardMan 4040 smartcard reader
2362 device amdsbwd # AMD South Bridge watchdog
2363 device gpio # Enable support for the gpio framework
2364 device ichwd # Intel ICH watchdog interrupt timer
2365 device tbridge # regression testing
2370 device virtio # VirtIO core
2371 device virtio_blk # VirtIO disk driver
2372 device virtio_pci # VirtIO transport over PCI bus
2375 # Embedded system options:
2377 # An embedded system might want to run something other than init.
2378 options INIT_PATH="/sbin/init:/sbin/oinit"
2381 options BUS_DEBUG # enable newbus debugging
2382 options NPX_DEBUG # enable npx debugging (FPU/math emu)
2383 options RSS_DEBUG # enable RSS (Receive Side Scaling) debugging
2385 # Record the program counter of the code interrupted by the statistics
2386 # clock interrupt. Use pctrack(8) to dump this information.
2387 options DEBUG_PCTRACK
2389 # More undocumented options for linting.
2390 # Note that documenting these are not considered an affront.
2392 #options ACPI_NO_SEMAPHORES
2393 options AHC_DUMP_EEPROM
2394 #options BKTR_ALLOC_PAGES=xxx
2395 options CAM_DEBUG_DELAY
2396 options CLUSTERDEBUG
2397 options COMPAT_LINUX
2399 options DEBUG_CRIT_SECTIONS
2400 options DEBUG_INTERRUPTS
2401 #options DISABLE_PSE
2402 options BCE_RSS_DEBUG
2403 options BCE_TSS_DEBUG
2404 options BNX_RSS_DEBUG
2405 options BNX_TSO_DEBUG
2406 options BNX_TSS_DEBUG
2407 options EMX_RSS_DEBUG
2408 options EMX_TSO_DEBUG
2409 options EMX_TSS_DEBUG
2410 options JME_RSS_DEBUG
2411 options IGB_RSS_DEBUG
2412 options IGB_TSS_DEBUG
2413 options IGB_MSIX_DEBUG
2414 #options ED_NO_MIIBUS
2415 options ENABLE_ALART
2417 options FB_INSTALL_CDEV
2418 options FE_8BIT_SUPPORT
2419 options I586_PMC_GUPROF=0x70000
2420 #options IEEE80211_DEBUG_REFCNT
2421 options IEEE80211_SUPPORT_SUPERG
2422 options KBDIO_DEBUG=10
2423 options KBD_MAXRETRY=4
2424 options KBD_MAXWAIT=6
2425 options KBD_RESETDELAY=201
2426 options KERN_TIMESTAMP
2430 #options MAXFILES=xxx
2432 options NO_LWKT_SPLIT_USERPRI
2436 options SCSI_NCR_DEBUG
2437 options SCSI_NCR_MAX_SYNC=10000
2438 options SCSI_NCR_MAX_WIDE=1
2439 options SCSI_NCR_MYADDR=7
2440 options SHOW_BUSYBUFS # List buffers that prevent root unmount
2443 options SLIP_IFF_OPTS
2444 options SOCKBUF_DEBUG
2445 options TDMA_BINTVAL_DEFAULT=5
2446 options TDMA_SLOTCNT_DEFAULT=2
2447 options TDMA_SLOTLEN_DEFAULT=10*1000
2448 options TDMA_TXRATE_11A_DEFAULT=2*24
2449 options TDMA_TXRATE_11B_DEFAULT=2*11
2450 options TDMA_TXRATE_11G_DEFAULT=2*24
2451 options TDMA_TXRATE_11NA_DEFAULT="(4|IEEE80211_RATE_MCS)"
2452 options TDMA_TXRATE_11NG_DEFAULT="(4|IEEE80211_RATE_MCS)"
2453 options TDMA_TXRATE_HALF_DEFAULT=2*12
2454 options TDMA_TXRATE_QUARTER_DEFAULT=2*6
2455 options TDMA_TXRATE_TURBO_DEFAULT=2*24
2456 options TIMER_FREQ="((14318182+6)/12)"
2457 options VFS_BIO_DEBUG
2458 options VM_PAGE_DEBUG
2463 options KTR_ENTRIES=1024
2464 options KTR_VERBOSE=1
2466 #options KTR_DMCRYPT
2467 #options KTR_DSCHED_BFQ
2468 #options KTR_ETHERNET
2474 #options KTR_IF_POLL
2475 #options KTR_IF_START
2477 #options KTR_KERNENTRY
2479 #options KTR_SERIALIZER
2480 #options KTR_SPIN_CONTENTION
2481 #options KTR_TESTLOG
2484 #options KTR_USB_MEMORY
2485 #options KTR_USCHED_BSD4
2486 #options KTR_USCHED_DFLY
2489 options ALTQ #alternate queueing
2490 options ALTQ_CBQ #class based queueing
2491 options ALTQ_RED #random early detection
2492 options ALTQ_RIO #triple red for diffserv (needs RED)
2493 options ALTQ_HFSC #hierarchical fair service curve
2494 options ALTQ_PRIQ #priority queue
2495 options ALTQ_FAIRQ #fair queue
2496 #options ALTQ_NOPCC #don't use processor cycle counter
2497 options ALTQ_DEBUG #for debugging
2498 # you might want to set kernel timer to 1kHz if you use CBQ,
2499 # especially with 100baseT
2505 options SCTP_USE_ADLER32
2506 options SCTP_HIGH_SPEED
2507 options SCTP_STAT_LOGGING
2508 options SCTP_CWND_LOGGING
2509 options SCTP_BLK_LOGGING
2510 options SCTP_STR_LOGGING
2511 options SCTP_FR_LOGGING
2512 options SCTP_MAP_LOGGING
2520 options WDOG_DISABLE_ON_PANIC # Automatically disable watchdogs on panic
2523 options ERROR_LED_ON_PANIC # If an error led is present, light it up on panic